* [PATCH] enable built-in networking for Sequoia defconfig
@ 2008-01-04 23:26 Hollis Blanchard
2008-01-08 16:09 ` Josh Boyer
0 siblings, 1 reply; 8+ messages in thread
From: Hollis Blanchard @ 2008-01-04 23:26 UTC (permalink / raw)
To: Josh Boyer; +Cc: linuxppc-dev
Enable EMAC driver for Sequoia (and while we're in there, disable
Macintosh drivers for Sequoia and Bamboo).
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
diff --git a/arch/powerpc/configs/bamboo_defconfig b/arch/powerpc/configs/bamboo_defconfig
--- a/arch/powerpc/configs/bamboo_defconfig
+++ b/arch/powerpc/configs/bamboo_defconfig
@@ -372,9 +372,7 @@ CONFIG_MISC_DEVICES=y
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
-CONFIG_MACINTOSH_DRIVERS=y
-# CONFIG_MAC_EMUMOUSEBTN is not set
-# CONFIG_WINDFARM is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
CONFIG_NETDEVICES=y
# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
diff --git a/arch/powerpc/configs/sequoia_defconfig b/arch/powerpc/configs/sequoia_defconfig
--- a/arch/powerpc/configs/sequoia_defconfig
+++ b/arch/powerpc/configs/sequoia_defconfig
@@ -446,9 +446,7 @@ CONFIG_MISC_DEVICES=y
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
-CONFIG_MACINTOSH_DRIVERS=y
-# CONFIG_MAC_EMUMOUSEBTN is not set
-# CONFIG_WINDFARM is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
CONFIG_NETDEVICES=y
# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
@@ -459,10 +457,28 @@ CONFIG_NETDEVICES=y
# CONFIG_VETH is not set
# CONFIG_IP1000 is not set
# CONFIG_ARCNET is not set
-# CONFIG_NET_ETHERNET is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+# CONFIG_MII is not set
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+CONFIG_IBM_NEW_EMAC=y
+CONFIG_IBM_NEW_EMAC_RXB=128
+CONFIG_IBM_NEW_EMAC_TXB=64
+CONFIG_IBM_NEW_EMAC_POLL_WEIGHT=32
+CONFIG_IBM_NEW_EMAC_RX_COPY_THRESHOLD=256
+CONFIG_IBM_NEW_EMAC_RX_SKB_HEADROOM=0
+# CONFIG_IBM_NEW_EMAC_DEBUG is not set
CONFIG_IBM_NEW_EMAC_ZMII=y
CONFIG_IBM_NEW_EMAC_RGMII=y
+# CONFIG_IBM_NEW_EMAC_TAH is not set
CONFIG_IBM_NEW_EMAC_EMAC4=y
+# CONFIG_NET_PCI is not set
+# CONFIG_B44 is not set
CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH] enable built-in networking for Sequoia defconfig
2008-01-04 23:26 [PATCH] enable built-in networking for Sequoia defconfig Hollis Blanchard
@ 2008-01-08 16:09 ` Josh Boyer
2008-01-09 11:16 ` Matthias Fuchs
0 siblings, 1 reply; 8+ messages in thread
From: Josh Boyer @ 2008-01-08 16:09 UTC (permalink / raw)
To: Hollis Blanchard; +Cc: linuxppc-dev
On Fri, 04 Jan 2008 17:26:54 -0600
Hollis Blanchard <hollisb@us.ibm.com> wrote:
> Enable EMAC driver for Sequoia (and while we're in there, disable
> Macintosh drivers for Sequoia and Bamboo).
>
> Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
applied, thanks.
josh
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH] enable built-in networking for Sequoia defconfig
2008-01-08 16:09 ` Josh Boyer
@ 2008-01-09 11:16 ` Matthias Fuchs
2008-01-09 12:07 ` Josh Boyer
0 siblings, 1 reply; 8+ messages in thread
From: Matthias Fuchs @ 2008-01-09 11:16 UTC (permalink / raw)
To: linuxppc-dev
Josh,
Where did you apply this patch to? Couldn't find it in your for-2.6.25 branch.
BTW, is it normal to edit the defconfig file by hand?
I cannot get CONFIG_IBM_NEW_EMAC enabled through Kconfig. Am I missing something:
a) Patch to enable IBM_NEW_EMAC via Kconfig is welcome
b) Matthias only knows only half the truth.
Matthias
On Tuesday 08 January 2008 17:09, Josh Boyer wrote:
> On Fri, 04 Jan 2008 17:26:54 -0600
> Hollis Blanchard <hollisb@us.ibm.com> wrote:
>
> > Enable EMAC driver for Sequoia (and while we're in there, disable
> > Macintosh drivers for Sequoia and Bamboo).
> >
> > Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
>
> applied, thanks.
>
> josh
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-dev
>
>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH] enable built-in networking for Sequoia defconfig
2008-01-09 11:16 ` Matthias Fuchs
@ 2008-01-09 12:07 ` Josh Boyer
2008-01-09 14:42 ` Matthias Fuchs
0 siblings, 1 reply; 8+ messages in thread
From: Josh Boyer @ 2008-01-09 12:07 UTC (permalink / raw)
To: Matthias Fuchs; +Cc: linuxppc-dev
On Wed, 9 Jan 2008 12:16:25 +0100
Matthias Fuchs <matthias.fuchs@esd-electronics.com> wrote:
> Josh,
>
> Where did you apply this patch to? Couldn't find it in your for-2.6.25 branch.
I applied it there, just haven't pushed it out yet. Will do that today.
> BTW, is it normal to edit the defconfig file by hand?
The defconfig? Not sure. What I normally do is a make foo_defconfig,
edit the .config, make oldconfig, and copy the resulting .config back
to foo_defconfig.
josh
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH] enable built-in networking for Sequoia defconfig
2008-01-09 12:07 ` Josh Boyer
@ 2008-01-09 14:42 ` Matthias Fuchs
2008-01-09 15:06 ` Stefan Roese
2008-01-09 15:21 ` Josh Boyer
0 siblings, 2 replies; 8+ messages in thread
From: Matthias Fuchs @ 2008-01-09 14:42 UTC (permalink / raw)
To: Josh Boyer; +Cc: linuxppc-dev, Hollis Blanchard
On Wednesday 09 January 2008 13:07, Josh Boyer wrote:
> On Wed, 9 Jan 2008 12:16:25 +0100
> Matthias Fuchs <matthias.fuchs@esd-electronics.com> wrote:
>
> > Josh,
> >
> > Where did you apply this patch to? Couldn't find it in your for-2.6.25 branch.
>
> I applied it there, just haven't pushed it out yet. Will do that today.
>
> > BTW, is it normal to edit the defconfig file by hand?
>
> The defconfig? Not sure. What I normally do is a make foo_defconfig,
> edit the .config, make oldconfig, and copy the resulting .config back
> to foo_defconfig.
Yes, this is what I also do.
But how did Hollis get these lines into .config or sequoia_defconfig:
+CONFIG_IBM_NEW_EMAC=y
+CONFIG_IBM_NEW_EMAC_RXB=128
+CONFIG_IBM_NEW_EMAC_TXB=64
+CONFIG_IBM_NEW_EMAC_POLL_WEIGHT=32
+CONFIG_IBM_NEW_EMAC_RX_COPY_THRESHOLD=256
+CONFIG_IBM_NEW_EMAC_RX_SKB_HEADROOM=0
I did not find any Kconfigs where these might come from.
Any hint?
Matthias
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH] enable built-in networking for Sequoia defconfig
2008-01-09 14:42 ` Matthias Fuchs
@ 2008-01-09 15:06 ` Stefan Roese
2008-01-09 15:21 ` Josh Boyer
1 sibling, 0 replies; 8+ messages in thread
From: Stefan Roese @ 2008-01-09 15:06 UTC (permalink / raw)
To: linuxppc-dev; +Cc: Hollis Blanchard
On Wednesday 09 January 2008, Matthias Fuchs wrote:
> > The defconfig? Not sure. What I normally do is a make foo_defconfig,
> > edit the .config, make oldconfig, and copy the resulting .config back
> > to foo_defconfig.
>
> Yes, this is what I also do.
>
> But how did Hollis get these lines into .config or sequoia_defconfig:
>
> +CONFIG_IBM_NEW_EMAC=3Dy
> +CONFIG_IBM_NEW_EMAC_RXB=3D128
> +CONFIG_IBM_NEW_EMAC_TXB=3D64
> +CONFIG_IBM_NEW_EMAC_POLL_WEIGHT=3D32
> +CONFIG_IBM_NEW_EMAC_RX_COPY_THRESHOLD=3D256
> +CONFIG_IBM_NEW_EMAC_RX_SKB_HEADROOM=3D0
>
> I did not find any Kconfigs where these might come from.
Take a look at drivers/net/ibm_newemac/Kconfig.
Viele Gr=FC=DFe,
Stefan
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH] enable built-in networking for Sequoia defconfig
2008-01-09 14:42 ` Matthias Fuchs
2008-01-09 15:06 ` Stefan Roese
@ 2008-01-09 15:21 ` Josh Boyer
2008-01-09 15:39 ` Matthias Fuchs
1 sibling, 1 reply; 8+ messages in thread
From: Josh Boyer @ 2008-01-09 15:21 UTC (permalink / raw)
To: Matthias Fuchs; +Cc: linuxppc-dev, Hollis Blanchard
On Wed, 9 Jan 2008 15:42:38 +0100
Matthias Fuchs <matthias.fuchs@esd-electronics.com> wrote:
> On Wednesday 09 January 2008 13:07, Josh Boyer wrote:
> > On Wed, 9 Jan 2008 12:16:25 +0100
> > Matthias Fuchs <matthias.fuchs@esd-electronics.com> wrote:
> >
> > > Josh,
> > >
> > > Where did you apply this patch to? Couldn't find it in your for-2.6.25 branch.
> >
> > I applied it there, just haven't pushed it out yet. Will do that today.
> >
> > > BTW, is it normal to edit the defconfig file by hand?
> >
> > The defconfig? Not sure. What I normally do is a make foo_defconfig,
> > edit the .config, make oldconfig, and copy the resulting .config back
> > to foo_defconfig.
> Yes, this is what I also do.
>
> But how did Hollis get these lines into .config or sequoia_defconfig:
>
> +CONFIG_IBM_NEW_EMAC=y
> +CONFIG_IBM_NEW_EMAC_RXB=128
> +CONFIG_IBM_NEW_EMAC_TXB=64
> +CONFIG_IBM_NEW_EMAC_POLL_WEIGHT=32
> +CONFIG_IBM_NEW_EMAC_RX_COPY_THRESHOLD=256
> +CONFIG_IBM_NEW_EMAC_RX_SKB_HEADROOM=0
>
> I did not find any Kconfigs where these might come from.
They're in drivers/net/ibm_newemac/Kconfig.
josh
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH] enable built-in networking for Sequoia defconfig
2008-01-09 15:21 ` Josh Boyer
@ 2008-01-09 15:39 ` Matthias Fuchs
0 siblings, 0 replies; 8+ messages in thread
From: Matthias Fuchs @ 2008-01-09 15:39 UTC (permalink / raw)
To: Josh Boyer; +Cc: linuxppc-dev, Hollis Blanchard
Thanks,
Sorry, I must have been blind.
Matthias
On Wednesday 09 January 2008 16:21, Josh Boyer wrote:
> On Wed, 9 Jan 2008 15:42:38 +0100
> Matthias Fuchs <matthias.fuchs@esd-electronics.com> wrote:
>
> > On Wednesday 09 January 2008 13:07, Josh Boyer wrote:
> > > On Wed, 9 Jan 2008 12:16:25 +0100
> > > Matthias Fuchs <matthias.fuchs@esd-electronics.com> wrote:
> > >
> > > > Josh,
> > > >
> > > > Where did you apply this patch to? Couldn't find it in your for-2.6.25 branch.
> > >
> > > I applied it there, just haven't pushed it out yet. Will do that today.
> > >
> > > > BTW, is it normal to edit the defconfig file by hand?
> > >
> > > The defconfig? Not sure. What I normally do is a make foo_defconfig,
> > > edit the .config, make oldconfig, and copy the resulting .config back
> > > to foo_defconfig.
> > Yes, this is what I also do.
> >
> > But how did Hollis get these lines into .config or sequoia_defconfig:
> >
> > +CONFIG_IBM_NEW_EMAC=y
> > +CONFIG_IBM_NEW_EMAC_RXB=128
> > +CONFIG_IBM_NEW_EMAC_TXB=64
> > +CONFIG_IBM_NEW_EMAC_POLL_WEIGHT=32
> > +CONFIG_IBM_NEW_EMAC_RX_COPY_THRESHOLD=256
> > +CONFIG_IBM_NEW_EMAC_RX_SKB_HEADROOM=0
> >
> > I did not find any Kconfigs where these might come from.
>
> They're in drivers/net/ibm_newemac/Kconfig.
>
> josh
>
>
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2008-01-09 15:42 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-01-04 23:26 [PATCH] enable built-in networking for Sequoia defconfig Hollis Blanchard
2008-01-08 16:09 ` Josh Boyer
2008-01-09 11:16 ` Matthias Fuchs
2008-01-09 12:07 ` Josh Boyer
2008-01-09 14:42 ` Matthias Fuchs
2008-01-09 15:06 ` Stefan Roese
2008-01-09 15:21 ` Josh Boyer
2008-01-09 15:39 ` Matthias Fuchs
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).