From: Marian Balakowicz <m8@semihalf.com>
To: linuxppc-dev@ozlabs.org
Subject: [PATCH v2] [POWERPC] Update TQM5200, CM5200 and Motion-PRO .dts files
Date: Thu, 17 Jan 2008 19:07:21 +0100 [thread overview]
Message-ID: <20080117180708.17979.9172.stgit@hekate.izotz.org> (raw)
Updates include:
- set soc mnode compatible property to "fsl,mpc5200-immr"
- update i2c device tree nodes
- add mdio node
- add lpb bus node and flash device (without partitions defined)
- add second mscan node for Motio-PRO
- add rtc i2c nodes
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
---
This patch was applied and tested against:
git://git.secretlab.ca/git/linux-2.6-mpc52xx.git#for-2.6.25
arch/powerpc/boot/dts/cm5200.dts | 40 +++++++++++++++++++++++++++--
arch/powerpc/boot/dts/motionpro.dts | 49 ++++++++++++++++++++++++++++++++---
arch/powerpc/boot/dts/tqm5200.dts | 45 +++++++++++++++++++++++++++++++-
3 files changed, 126 insertions(+), 8 deletions(-)
diff --git a/arch/powerpc/boot/dts/cm5200.dts b/arch/powerpc/boot/dts/cm5200.dts
index 9295083..ff01478 100644
--- a/arch/powerpc/boot/dts/cm5200.dts
+++ b/arch/powerpc/boot/dts/cm5200.dts
@@ -46,7 +46,7 @@
soc5200@f0000000 {
model = "fsl,mpc5200b";
- compatible = "fsl,mpc5200b";
+ compatible = "fsl,mpc5200-immr";
revision = ""; // from bootloader
device_type = "soc";
ranges = <0 f0000000 0000c000>;
@@ -214,13 +214,31 @@
ethernet@3000 {
device_type = "network";
compatible = "mpc5200b-fec","mpc5200-fec";
- reg = <3000 800>;
+ reg = <3000 400>;
local-mac-address = [ 00 00 00 00 00 00 ]; /* Filled in by U-Boot */
interrupts = <2 5 0>;
interrupt-parent = <&mpc5200_pic>;
+ phy-handle = <&phy0>;
+ };
+
+ mdio@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ device_type = "mdio";
+ compatible = "mpc5200b-fec-phy";
+ reg = <3000 400>; // fec range, since we need to setup fec interrupts
+ interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
+ interrupt-parent = <&mpc5200_pic>;
+
+ phy0:ethernet-phy@0 {
+ device_type = "ethernet-phy";
+ reg = <0>;
+ };
};
i2c@3d40 {
+ #address-cells = <1>;
+ #size-cells = <0>;
compatible = "mpc5200b-i2c","mpc5200-i2c","fsl-i2c";
reg = <3d40 40>;
interrupts = <2 10 0>;
@@ -233,4 +251,22 @@
reg = <8000 4000>;
};
};
+
+ lpb {
+ model = "fsl,lpb";
+ compatible = "fsl,lpb";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 fc000000 2000000>;
+
+ // 16-bit flash device at LocalPlus Bus CS0
+ flash@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 2000000>;
+ bank-width = <2>;
+ device-width = <2>;
+ #size-cells = <1>;
+ #address-cells = <1>;
+ };
+ };
};
diff --git a/arch/powerpc/boot/dts/motionpro.dts b/arch/powerpc/boot/dts/motionpro.dts
index d8c316a..1a046aa 100644
--- a/arch/powerpc/boot/dts/motionpro.dts
+++ b/arch/powerpc/boot/dts/motionpro.dts
@@ -46,7 +46,7 @@
soc5200@f0000000 {
model = "fsl,mpc5200b";
- compatible = "fsl,mpc5200b";
+ compatible = "fsl,mpc5200-immr";
revision = ""; // from bootloader
device_type = "soc";
ranges = <0 f0000000 0000c000>;
@@ -134,6 +134,13 @@
interrupt-parent = <&mpc5200_pic>;
};
+ mscan@900 {
+ compatible = "mpc5200b-mscan\0mpc5200-mscan";
+ interrupts = <2 11 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ reg = <900 80>;
+ };
+
mscan@980 {
compatible = "mpc5200b-mscan","mpc5200-mscan";
interrupts = <2 12 0>;
@@ -155,7 +162,6 @@
interrupt-parent = <&mpc5200_pic>;
};
-
spi@f00 {
compatible = "mpc5200b-spi","mpc5200-spi";
reg = <f00 20>;
@@ -216,10 +222,26 @@
ethernet@3000 {
device_type = "network";
compatible = "mpc5200b-fec","mpc5200-fec";
- reg = <3000 800>;
+ reg = <3000 400>;
local-mac-address = [ 00 00 00 00 00 00 ]; /* Filled in by U-Boot */
interrupts = <2 5 0>;
interrupt-parent = <&mpc5200_pic>;
+ phy-handle = <&phy0>;
+ };
+
+ mdio@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ device_type = "mdio";
+ compatible = "mpc5200b-fec-phy";
+ reg = <3000 400>; // fec range, since we need to setup fec interrupts
+ interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
+ interrupt-parent = <&mpc5200_pic>;
+
+ phy0:ethernet-phy@0 {
+ device_type = "ethernet-phy";
+ reg = <0>;
+ };
};
ata@3a00 {
@@ -230,11 +252,19 @@
};
i2c@3d40 {
+ #address-cells = <1>;
+ #size-cells = <0>;
compatible = "mpc5200b-i2c","mpc5200-i2c","fsl-i2c";
reg = <3d40 40>;
interrupts = <2 10 0>;
interrupt-parent = <&mpc5200_pic>;
fsl5200-clocking;
+
+ rtc@68 {
+ device_type = "rtc";
+ compatible = "dallas,ds1339";
+ reg = <68>;
+ };
};
sram@8000 {
@@ -248,7 +278,8 @@
compatible = "fsl,lpb";
#address-cells = <2>;
#size-cells = <1>;
- ranges = <1 0 50000000 00010000
+ ranges = <0 0 ff000000 01000000
+ 1 0 50000000 00010000
2 0 50010000 00010000
3 0 50020000 00010000>;
@@ -279,6 +310,16 @@
compatible = "promess,pro_module_dio";
reg = <3 800 2>;
};
+
+ // 16-bit flash device at LocalPlus Bus CS0
+ flash@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 01000000>;
+ bank-width = <2>;
+ device-width = <2>;
+ #size-cells = <1>;
+ #address-cells = <1>;
+ };
};
pci@f0000d00 {
diff --git a/arch/powerpc/boot/dts/tqm5200.dts b/arch/powerpc/boot/dts/tqm5200.dts
index 5017cec..54fb2a2 100644
--- a/arch/powerpc/boot/dts/tqm5200.dts
+++ b/arch/powerpc/boot/dts/tqm5200.dts
@@ -46,7 +46,7 @@
soc5200@f0000000 {
model = "fsl,mpc5200";
- compatible = "fsl,mpc5200";
+ compatible = "fsl,mpc5200-immr";
revision = ""; // from bootloader
device_type = "soc";
ranges = <0 f0000000 0000c000>;
@@ -134,10 +134,26 @@
ethernet@3000 {
device_type = "network";
compatible = "mpc5200-fec";
- reg = <3000 800>;
+ reg = <3000 400>;
local-mac-address = [ 00 00 00 00 00 00 ]; /* Filled in by U-Boot */
interrupts = <2 5 0>;
interrupt-parent = <&mpc5200_pic>;
+ phy-handle = <&phy0>;
+ };
+
+ mdio@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ device_type = "mdio";
+ compatible = "mpc5200b-fec-phy";
+ reg = <3000 400>; // fec range, since we need to setup fec interrupts
+ interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
+ interrupt-parent = <&mpc5200_pic>;
+
+ phy0:ethernet-phy@0 {
+ device_type = "ethernet-phy";
+ reg = <0>;
+ };
};
ata@3a00 {
@@ -148,11 +164,19 @@
};
i2c@3d40 {
+ #address-cells = <1>;
+ #size-cells = <0>;
compatible = "mpc5200-i2c","fsl-i2c";
reg = <3d40 40>;
interrupts = <2 10 0>;
interrupt-parent = <&mpc5200_pic>;
fsl5200-clocking;
+
+ rtc@68 {
+ device_type = "rtc";
+ compatible = "dallas,ds1307";
+ reg = <68>;
+ };
};
sram@8000 {
@@ -161,6 +185,23 @@
};
};
+ lpb {
+ model = "fsl,lpb";
+ compatible = "fsl,lpb";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 fc000000 02000000>;
+
+ flash@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 02000000>;
+ bank-width = <4>;
+ device-width = <2>;
+ #size-cells = <1>;
+ #address-cells = <1>;
+ };
+ };
+
pci@f0000d00 {
#interrupt-cells = <1>;
#size-cells = <2>;
reply other threads:[~2008-01-17 18:06 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20080117180708.17979.9172.stgit@hekate.izotz.org \
--to=m8@semihalf.com \
--cc=linuxppc-dev@ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox