* [PATCH 1/4] Emerson KSI8560 base support
2008-03-04 16:23 [PATCH 0/4] Add Emerson KSI8560 board support Alexandr Smirnov
@ 2008-03-04 16:33 ` Alexandr Smirnov
2008-03-04 16:34 ` [PATCH 2/4] Emerson KSI8560 bootwrapper Alexandr Smirnov
` (4 subsequent siblings)
5 siblings, 0 replies; 17+ messages in thread
From: Alexandr Smirnov @ 2008-03-04 16:33 UTC (permalink / raw)
To: linuxppc-dev
The KSI8560 is a single compact, mid-, or full-size Advanced Mezzanine Card
(AdvancedMC™) based on the Freescale™ Semiconductor MPC8560 PowerQUICC III™
microprocessor. This product will serve in data and signaling applications such
as signaling gateways (SGW) and softswitch signaling interface cards.
The board has altera maxii CPLD, that is used to obtain and manage board
configuration. Also there are two SCC UART serial consoles and FCC ethernet,
that is routed to the front panel, while other ethernet controlers (TSEC's) are
routed to the backplane.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
arch/powerpc/platforms/85xx/Kconfig | 7
arch/powerpc/platforms/85xx/Makefile | 1
arch/powerpc/platforms/85xx/ksi8560.c | 257 ++++++++++++++++++++++++++++++++++
3 files changed, 265 insertions(+)
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index 7e76ddb..28bc6e5 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -46,6 +46,13 @@ config MPC85xx_DS
help
This option enables support for the MPC85xx DS (MPC8544 DS) board
+config KSI8560
+ bool "Emerson KSI8560"
+ select PPC_CPM_NEW_BINDING
+ select DEFAULT_UIMAGE
+ help
+ This option enables support for the Emerson KSI8560 board
+
config STX_GP3
bool "Silicon Turnkey Express GP3"
help
diff --git a/arch/powerpc/platforms/85xx/Makefile b/arch/powerpc/platforms/85xx/Makefile
index cb7af4e..6cea185 100644
--- a/arch/powerpc/platforms/85xx/Makefile
+++ b/arch/powerpc/platforms/85xx/Makefile
@@ -10,3 +10,4 @@ obj-$(CONFIG_STX_GP3) += stx_gp3.o
obj-$(CONFIG_TQM85xx) += tqm85xx.o
obj-$(CONFIG_SBC8560) += sbc8560.o
obj-$(CONFIG_SBC8548) += sbc8548.o
+obj-$(CONFIG_KSI8560) += ksi8560.o
diff --git a/arch/powerpc/platforms/85xx/ksi8560.c b/arch/powerpc/platforms/85xx/ksi8560.c
new file mode 100644
index 0000000..b3b8194
--- /dev/null
+++ b/arch/powerpc/platforms/85xx/ksi8560.c
@@ -0,0 +1,257 @@
+/*
+ * Board setup routines for the Emerson KSI8560
+ *
+ * Author: Alexandr Smirnov <asmirnov@ru.mvista.com>
+ *
+ * Based on mpc85xx_ads.c maintained by Kumar Gala
+ *
+ * 2008 (c) MontaVista, Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ *
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/kdev_t.h>
+#include <linux/delay.h>
+#include <linux/seq_file.h>
+#include <linux/of_platform.h>
+
+#include <asm/system.h>
+#include <asm/time.h>
+#include <asm/machdep.h>
+#include <asm/pci-bridge.h>
+#include <asm/mpic.h>
+#include <mm/mmu_decl.h>
+#include <asm/udbg.h>
+#include <asm/prom.h>
+
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+
+#include <asm/cpm2.h>
+#include <sysdev/cpm2_pic.h>
+
+
+#define KSI8560_CPLD_HVR 0x04 /* Hardware Version Register */
+#define KSI8560_CPLD_PVR 0x08 /* PLD Version Register */
+#define KSI8560_CPLD_RCR1 0x30 /* Reset Command Register 1 */
+
+#define KSI8560_CPLD_RCR1_CPUHR 0x80 /* CPU Hard Reset */
+
+static void __iomem *cpld_base = NULL;
+
+static void machine_restart(char *cmd)
+{
+ if (cpld_base)
+ out_8(cpld_base + KSI8560_CPLD_RCR1, KSI8560_CPLD_RCR1_CPUHR);
+ else
+ printk(KERN_ERR "Can't find CPLD base, hang forever\n");
+
+ for (;;);
+}
+
+static void cpm2_cascade(unsigned int irq, struct irq_desc *desc)
+{
+ int cascade_irq;
+
+ while ((cascade_irq = cpm2_get_irq()) >= 0)
+ generic_handle_irq(cascade_irq);
+
+ desc->chip->eoi(irq);
+}
+
+static void __init ksi8560_pic_init(void)
+{
+ struct mpic *mpic;
+ struct resource r;
+ struct device_node *np;
+#ifdef CONFIG_CPM2
+ int irq;
+#endif
+
+ np = of_find_node_by_type(NULL, "open-pic");
+
+ if (np == NULL) {
+ printk(KERN_ERR "Could not find open-pic node\n");
+ return;
+ }
+
+ if (of_address_to_resource(np, 0, &r)) {
+ printk(KERN_ERR "Could not map mpic register space\n");
+ of_node_put(np);
+ return;
+ }
+
+ mpic = mpic_alloc(np, r.start,
+ MPIC_PRIMARY | MPIC_WANTS_RESET | MPIC_BIG_ENDIAN,
+ 0, 256, " OpenPIC ");
+ BUG_ON(mpic == NULL);
+ of_node_put(np);
+
+ mpic_init(mpic);
+
+#ifdef CONFIG_CPM2
+ /* Setup CPM2 PIC */
+ np = of_find_compatible_node(NULL, NULL, "fsl,cpm2-pic");
+ if (np == NULL) {
+ printk(KERN_ERR "PIC init: can not find fsl,cpm2-pic node\n");
+ return;
+ }
+ irq = irq_of_parse_and_map(np, 0);
+
+ cpm2_pic_init(np);
+ of_node_put(np);
+ set_irq_chained_handler(irq, cpm2_cascade);
+
+ setup_irq(0, NULL);
+#endif
+}
+
+#ifdef CONFIG_CPM2
+/*
+ * Setup I/O ports
+ */
+struct cpm_pin {
+ int port, pin, flags;
+};
+
+static struct cpm_pin __initdata ksi8560_pins[] = {
+ /* SCC1 */
+ {3, 29, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {3, 30, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {3, 31, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+
+ /* SCC2 */
+ {3, 26, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {3, 27, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {3, 28, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+
+ /* FCC1 */
+ {0, 14, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 15, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 16, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 17, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 18, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 19, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 20, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 21, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 26, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {0, 27, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {0, 28, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {0, 29, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {0, 30, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {0, 31, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {2, 23, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, /* CLK9 */
+ {2, 22, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, /* CLK10 */
+
+};
+
+static void __init init_ioports(void)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(ksi8560_pins); i++) {
+ struct cpm_pin *pin = &ksi8560_pins[i];
+ cpm2_set_pin(pin->port, pin->pin, pin->flags);
+ }
+
+ cpm2_clk_setup(CPM_CLK_SCC1, CPM_BRG1, CPM_CLK_RX);
+ cpm2_clk_setup(CPM_CLK_SCC1, CPM_BRG1, CPM_CLK_TX);
+ cpm2_clk_setup(CPM_CLK_SCC2, CPM_BRG2, CPM_CLK_RX);
+ cpm2_clk_setup(CPM_CLK_SCC2, CPM_BRG2, CPM_CLK_TX);
+ cpm2_clk_setup(CPM_CLK_FCC1, CPM_CLK9, CPM_CLK_RX);
+ cpm2_clk_setup(CPM_CLK_FCC1, CPM_CLK10, CPM_CLK_TX);
+}
+#endif
+
+/*
+ * Setup the architecture
+ */
+static void __init ksi8560_setup_arch(void)
+{
+ struct device_node *cpld;
+
+ cpld = of_find_compatible_node(NULL, NULL, "altera,maxii");
+ if (cpld)
+ cpld_base = of_iomap(cpld, 0);
+ else
+ printk(KERN_ERR "Can't find CPLD in device tree\n");
+
+ if (ppc_md.progress)
+ ppc_md.progress("ksi8560_setup_arch()", 0);
+
+#ifdef CONFIG_CPM2
+ cpm2_reset();
+ init_ioports();
+#endif
+}
+
+static void ksi8560_show_cpuinfo(struct seq_file *m)
+{
+ uint pvid, svid, phid1;
+ uint memsize = total_memory;
+
+ pvid = mfspr(SPRN_PVR);
+ svid = mfspr(SPRN_SVR);
+
+ seq_printf(m, "Vendor\t\t: Emerson Network Power\n");
+ seq_printf(m, "Board\t\t: KSI8560\n");
+
+ if (cpld_base) {
+ seq_printf(m, "Hardware rev\t: %d\n",
+ in_8(cpld_base + KSI8560_CPLD_HVR));
+ seq_printf(m, "CPLD rev\t: %d\n",
+ in_8(cpld_base + KSI8560_CPLD_PVR));
+ } else
+ seq_printf(m, "Unknown Hardware and CPLD revs\n");
+
+ seq_printf(m, "PVR\t\t: 0x%x\n", pvid);
+ seq_printf(m, "SVR\t\t: 0x%x\n", svid);
+
+ /* Display cpu Pll setting */
+ phid1 = mfspr(SPRN_HID1);
+ seq_printf(m, "PLL setting\t: 0x%x\n", ((phid1 >> 24) & 0x3f));
+
+ /* Display the amount of memory */
+ seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
+}
+
+static struct of_device_id __initdata of_bus_ids[] = {
+ { .type = "soc", },
+ { .name = "cpm", },
+ { .name = "localbus", },
+ {},
+};
+
+static int __init declare_of_platform_devices(void)
+{
+ of_platform_bus_probe(NULL, of_bus_ids, NULL);
+
+ return 0;
+}
+machine_device_initcall(ksi8560, declare_of_platform_devices);
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init ksi8560_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+
+ return of_flat_dt_is_compatible(root, "emerson,KSI8560");
+}
+
+define_machine(ksi8560) {
+ .name = "KSI8560",
+ .probe = ksi8560_probe,
+ .setup_arch = ksi8560_setup_arch,
+ .init_IRQ = ksi8560_pic_init,
+ .show_cpuinfo = ksi8560_show_cpuinfo,
+ .get_irq = mpic_get_irq,
+ .restart = machine_restart,
+ .calibrate_decr = generic_calibrate_decr,
+};
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH 2/4] Emerson KSI8560 bootwrapper
2008-03-04 16:23 [PATCH 0/4] Add Emerson KSI8560 board support Alexandr Smirnov
2008-03-04 16:33 ` [PATCH 1/4] Emerson KSI8560 base support Alexandr Smirnov
@ 2008-03-04 16:34 ` Alexandr Smirnov
2008-03-07 15:09 ` Kumar Gala
2008-03-04 16:35 ` [PATCH 3/4] Emerson KSI8560 device tree Alexandr Smirnov
` (3 subsequent siblings)
5 siblings, 1 reply; 17+ messages in thread
From: Alexandr Smirnov @ 2008-03-04 16:34 UTC (permalink / raw)
To: linuxppc-dev
Add boot wrapper for Emerson KSI8560 board.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
arch/powerpc/boot/Makefile | 1 +
arch/powerpc/boot/wrapper | 2 +-
2 files changed, 2 insertions(+), 1 deletion(-)
diff --git a/arch/powerpc/boot/Makefile b/arch/powerpc/boot/Makefile
index e3993a6..f43dd6e 100644
--- a/arch/powerpc/boot/Makefile
+++ b/arch/powerpc/boot/Makefile
@@ -255,6 +255,7 @@ image-$(CONFIG_TQM8555) += cuImage.tqm8555
image-$(CONFIG_TQM8560) += cuImage.tqm8560
image-$(CONFIG_SBC8548) += cuImage.tqm8548
image-$(CONFIG_SBC8560) += cuImage.tqm8560
+image-$(CONFIG_KSI8560) += cuImage.ksi8560
# Board ports in arch/powerpc/platform/embedded6xx/Kconfig
image-$(CONFIG_STORCENTER) += cuImage.storcenter
diff --git a/arch/powerpc/boot/wrapper b/arch/powerpc/boot/wrapper
index c317815..6655a90 100755
--- a/arch/powerpc/boot/wrapper
+++ b/arch/powerpc/boot/wrapper
@@ -174,7 +174,7 @@ cuboot*)
*-mpc83*)
platformo=$object/cuboot-83xx.o
;;
- *-tqm8541|*-mpc8560*|*-tqm8560|*-tqm8555*)
+ *-tqm8541|*-mpc8560*|*-tqm8560|*-tqm8555*|*-ksi8560*)
platformo=$object/cuboot-85xx-cpm2.o
;;
*-mpc85*)
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH 3/4] Emerson KSI8560 device tree
2008-03-04 16:23 [PATCH 0/4] Add Emerson KSI8560 board support Alexandr Smirnov
2008-03-04 16:33 ` [PATCH 1/4] Emerson KSI8560 base support Alexandr Smirnov
2008-03-04 16:34 ` [PATCH 2/4] Emerson KSI8560 bootwrapper Alexandr Smirnov
@ 2008-03-04 16:35 ` Alexandr Smirnov
2008-03-04 23:29 ` David Gibson
2008-03-04 16:36 ` [PATCH 4/4] Emerson KSI8560 default config Alexandr Smirnov
` (2 subsequent siblings)
5 siblings, 1 reply; 17+ messages in thread
From: Alexandr Smirnov @ 2008-03-04 16:35 UTC (permalink / raw)
To: linuxppc-dev
Add device tree file for Emerson KSI8560 board.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
arch/powerpc/boot/dts/ksi8560.dts | 267 ++++++++++++++++++++++++++++++++++++++
1 file changed, 267 insertions(+)
diff --git a/arch/powerpc/boot/dts/ksi8560.dts b/arch/powerpc/boot/dts/ksi8560.dts
new file mode 100644
index 0000000..3956432
--- /dev/null
+++ b/arch/powerpc/boot/dts/ksi8560.dts
@@ -0,0 +1,267 @@
+/*
+ * Device Tree Source for Emerson KSI8560
+ *
+ * Author: Alexandr Smirnov <asmirnov@ru.mvista.com>
+ *
+ * Based on mpc8560ads.dts
+ *
+ * 2008 (c) MontaVista, Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ *
+ */
+
+/dts-v1/;
+
+/ {
+ model = "KSI8560";
+ compatible = "emerson,KSI8560";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ aliases {
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,8560@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <32>;
+ i-cache-line-size = <32>;
+ d-cache-size = <0x8000>; /* L1, 32K */
+ i-cache-size = <0x8000>; /* L1, 32K */
+ timebase-frequency = <0>; /* From U-boot */
+ bus-frequency = <0>; /* From U-boot */
+ clock-frequency = <0>; /* From U-boot */
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x10000000>; /* Fixed by bootwrapper */
+ };
+
+ soc@fdf00000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ ranges = <0x00000000 0xfdf00000 0x00100000>;
+ bus-frequency = <0>; /* Fixed by bootwrapper */
+
+ memory-controller@2000 {
+ compatible = "fsl,8540-memory-controller";
+ reg = <0x2000 0x1000>;
+ interrupt-parent = <&MPIC>;
+ interrupts = <0x12 0x2>;
+ };
+
+ l2-cache-controller@20000 {
+ compatible = "fsl,8540-l2-cache-controller";
+ reg = <0x20000 0x1000>;
+ cache-line-size = <0x20>; /* 32 bytes */
+ cache-size = <0x40000>; /* L2, 256K */
+ interrupt-parent = <&MPIC>;
+ interrupts = <0x10 0x2>;
+ };
+
+ i2c@3000 {
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <0x2b 0x2>;
+ interrupt-parent = <&MPIC>;
+ dfsrr;
+ };
+
+ mdio@24520 { /* For TSECs */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+
+ PHY1: ethernet-phy@1 {
+ interrupt-parent = <&MPIC>;
+ reg = <0x1>;
+ device_type = "ethernet-phy";
+ };
+
+ PHY2: ethernet-phy@2 {
+ interrupt-parent = <&MPIC>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ enet0: ethernet@24000 {
+ linux,network-index = <0>;
+ device_type = "network";
+ model = "TSEC";
+ compatible = "gianfar";
+ reg = <0x24000 0x1000>;
+ /* Mac address filled in by bootwrapper */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>;
+ interrupt-parent = <&MPIC>;
+ phy-handle = <&PHY1>;
+ };
+
+ enet1: ethernet@25000 {
+ linux,network-index = <1>;
+ device_type = "network";
+ model = "TSEC";
+ compatible = "gianfar";
+ reg = <0x25000 0x1000>;
+ /* Mac address filled in by bootwrapper */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <0x23 0x2 0x24 0x2 0x28 0x2>;
+ interrupt-parent = <&MPIC>;
+ phy-handle = <&PHY2>;
+ };
+
+ MPIC: pic@40000 {
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ reg = <0x40000 0x40000>;
+ device_type = "open-pic";
+ };
+
+ cpm@919c0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8560-cpm", "fsl,cpm2";
+ reg = <0x919c0 0x30>;
+ ranges;
+
+ muram@80000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x80000 0x10000>;
+
+ data@0 {
+ compatible = "fsl,cpm-muram-data";
+ reg = <0x0 0x4000 0x9000 0x2000>;
+ };
+ };
+
+ brg@919f0 {
+ compatible = "fsl,mpc8560-brg",
+ "fsl,cpm2-brg",
+ "fsl,cpm-brg";
+ reg = <0x919f0 0x10 0x915f0 0x10>;
+ clock-frequency = <165000000>; /* 166MHz */
+ };
+
+ CPMPIC: pic@90c00 {
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ interrupts = <0x2e 0x2>;
+ interrupt-parent = <&MPIC>;
+ reg = <0x90c00 0x80>;
+ compatible = "fsl,mpc8560-cpm-pic", "fsl,cpm2-pic";
+ };
+
+ serial@91a00 {
+ device_type = "serial";
+ compatible = "fsl,mpc8560-scc-uart",
+ "fsl,cpm2-scc-uart";
+ reg = <0x91a00 0x20 0x88000 0x100>;
+ fsl,cpm-brg = <1>;
+ fsl,cpm-command = <0x800000>;
+ current-speed = <0x1c200>;
+ interrupts = <0x28 0x8>;
+ interrupt-parent = <&CPMPIC>;
+ };
+
+ serial@91a20 {
+ device_type = "serial";
+ compatible = "fsl,mpc8560-scc-uart",
+ "fsl,cpm2-scc-uart";
+ reg = <0x91a20 0x20 0x88100 0x100>;
+ fsl,cpm-brg = <2>;
+ fsl,cpm-command = <0x4a00000>;
+ current-speed = <0x1c200>;
+ interrupts = <0x29 0x8>;
+ interrupt-parent = <&CPMPIC>;
+ };
+
+ mdio@90d00 { /* For FCCs */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,cpm2-mdio-bitbang";
+ reg = <0x90d00 0x14>;
+ fsl,mdio-pin = <24>;
+ fsl,mdc-pin = <25>;
+
+ PHY0: ethernet-phy@0 {
+ interrupt-parent = <&MPIC>;
+ reg = <0x0>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ enet2: ethernet@91300 {
+ linux,network-index = <2>;
+ device_type = "network";
+ compatible = "fsl,mpc8560-fcc-enet",
+ "fsl,cpm2-fcc-enet";
+ reg = <0x91300 0x20 0x88400 0x100 0x91390 0x1>;
+ /* Mac address filled in by bootwrapper */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ fsl,cpm-command = <0x12000300>;
+ interrupts = <0x20 0x8>;
+ interrupt-parent = <&CPMPIC>;
+ phy-handle = <&PHY0>;
+ };
+ };
+ };
+
+ localbus@fdf05000 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8560-localbus";
+ reg = <0xfdf05000 0x68>;
+
+ ranges = <0x0 0x0 0xe0000000 0x00800000
+ 0x4 0x0 0xe8080000 0x00080000>;
+
+ flash@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec-flash";
+ reg = <0x0 0x0 0x800000>;
+ bank-width = <0x2>;
+
+ partition@0 {
+ label = "Primary Kernel";
+ reg = <0x0 0x180000>;
+ };
+ partition@180000 {
+ label = "Primary Filesystem";
+ reg = <0x180000 0x580000>;
+ };
+ partition@700000 {
+ label = "Monitor";
+ reg = <0x300000 0x100000>;
+ read-only;
+ };
+ };
+
+ cpld@4,0 {
+ compatible = "altera,maxii";
+ reg = <0x4 0x0 0x80000>;
+ };
+ };
+
+
+ chosen {
+ linux,stdout-path = "/soc/cpm/serial@91a00";
+ };
+};
^ permalink raw reply related [flat|nested] 17+ messages in thread* Re: [PATCH 3/4] Emerson KSI8560 device tree
2008-03-04 16:35 ` [PATCH 3/4] Emerson KSI8560 device tree Alexandr Smirnov
@ 2008-03-04 23:29 ` David Gibson
2008-03-05 14:45 ` Alexandr Smirnov
2008-03-05 17:31 ` Scott Wood
0 siblings, 2 replies; 17+ messages in thread
From: David Gibson @ 2008-03-04 23:29 UTC (permalink / raw)
To: Alexandr Smirnov; +Cc: linuxppc-dev
On Tue, Mar 04, 2008 at 07:35:40PM +0300, Alexandr Smirnov wrote:
> Add device tree file for Emerson KSI8560 board.
>
> Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
[snip]
> + enet0: ethernet@24000 {
> + linux,network-index = <0>;
We're trying to get rid of this. Since I assume you're using u-boot,
I'm not sure why you'd need it now anyway.
> + device_type = "network";
> + model = "TSEC";
> + compatible = "gianfar";
This still looks like the old binding.
[snip]
> + cpld@4,0 {
> + compatible = "altera,maxii";
I'm guessing an Altera Maxii is just the name of the FPGA chip into
which the CPLD is programmed? If so, it's not a suitable "comaptible"
value, because that needs to describe the register interface. You
probably want something like
compatible = "emerson,KSI8560-cpld";
here.
--
David Gibson | I'll have my music baroque, and my code
david AT gibson.dropbear.id.au | minimalist, thank you. NOT _the_ _other_
| _way_ _around_!
http://www.ozlabs.org/~dgibson
^ permalink raw reply [flat|nested] 17+ messages in thread* Re: [PATCH 3/4] Emerson KSI8560 device tree
2008-03-04 23:29 ` David Gibson
@ 2008-03-05 14:45 ` Alexandr Smirnov
2008-03-05 17:31 ` Scott Wood
1 sibling, 0 replies; 17+ messages in thread
From: Alexandr Smirnov @ 2008-03-05 14:45 UTC (permalink / raw)
To: David Gibson; +Cc: linuxppc-dev
Hi
David, could you please explain what do you mean by "old bindind"? I
looked through ppc_dev listing,
documentation, and how it's done for other boards, but didn't find any
difference with my code. Maybe
you're talking about future changes in ethernet driver registration?
Thanks,
Alexandr.
David Gibson wrote:
>> + device_type = "network";
>> + model = "TSEC";
>> + compatible = "gianfar";
>>
>
> This still looks like the old binding.
>
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 3/4] Emerson KSI8560 device tree
2008-03-04 23:29 ` David Gibson
2008-03-05 14:45 ` Alexandr Smirnov
@ 2008-03-05 17:31 ` Scott Wood
2008-03-06 0:16 ` David Gibson
1 sibling, 1 reply; 17+ messages in thread
From: Scott Wood @ 2008-03-05 17:31 UTC (permalink / raw)
To: Alexandr Smirnov, linuxppc-dev
On Wed, Mar 05, 2008 at 10:29:40AM +1100, David Gibson wrote:
> On Tue, Mar 04, 2008 at 07:35:40PM +0300, Alexandr Smirnov wrote:
> > + device_type = "network";
> > + model = "TSEC";
> > + compatible = "gianfar";
>
> This still looks like the old binding.
Unfortunately, only the mdio node has a new binding. The gianfar driver
itself (or rather the glue code in fsl_soc.c) still insists on the above.
-Scott
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 3/4] Emerson KSI8560 device tree
2008-03-05 17:31 ` Scott Wood
@ 2008-03-06 0:16 ` David Gibson
0 siblings, 0 replies; 17+ messages in thread
From: David Gibson @ 2008-03-06 0:16 UTC (permalink / raw)
To: Scott Wood; +Cc: linuxppc-dev
On Wed, Mar 05, 2008 at 11:31:28AM -0600, Scott Wood wrote:
> On Wed, Mar 05, 2008 at 10:29:40AM +1100, David Gibson wrote:
> > On Tue, Mar 04, 2008 at 07:35:40PM +0300, Alexandr Smirnov wrote:
> > > + device_type = "network";
> > > + model = "TSEC";
> > > + compatible = "gianfar";
> >
> > This still looks like the old binding.
>
> Unfortunately, only the mdio node has a new binding. The gianfar driver
> itself (or rather the glue code in fsl_soc.c) still insists on the above.
Oh. Yuck :(.
--
David Gibson | I'll have my music baroque, and my code
david AT gibson.dropbear.id.au | minimalist, thank you. NOT _the_ _other_
| _way_ _around_!
http://www.ozlabs.org/~dgibson
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PATCH 4/4] Emerson KSI8560 default config
2008-03-04 16:23 [PATCH 0/4] Add Emerson KSI8560 board support Alexandr Smirnov
` (2 preceding siblings ...)
2008-03-04 16:35 ` [PATCH 3/4] Emerson KSI8560 device tree Alexandr Smirnov
@ 2008-03-04 16:36 ` Alexandr Smirnov
2008-03-07 15:09 ` Kumar Gala
2008-03-06 15:14 ` [PATCH 3/4] Emerson KSI8560 device tree Alexandr Smirnov
2008-03-06 15:17 ` [PATCH 1/4] Emerson KSI8560 base support Alexandr Smirnov
5 siblings, 1 reply; 17+ messages in thread
From: Alexandr Smirnov @ 2008-03-04 16:36 UTC (permalink / raw)
To: linuxppc-dev
Add default config for Emerson KSI8560 board.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
arch/powerpc/configs/ksi8560_defconfig | 899 +++++++++++++++++++++++++++++++++
1 file changed, 899 insertions(+)
diff --git a/arch/powerpc/configs/ksi8560_defconfig b/arch/powerpc/configs/ksi8560_defconfig
new file mode 100644
index 0000000..2d0debc
--- /dev/null
+++ b/arch/powerpc/configs/ksi8560_defconfig
@@ -0,0 +1,899 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.24
+# Mon Feb 11 16:25:19 2008
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+# CONFIG_6xx is not set
+CONFIG_PPC_85xx=y
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_E500=y
+CONFIG_BOOKE=y
+CONFIG_FSL_BOOKE=y
+CONFIG_FSL_EMB_PERFMON=y
+# CONFIG_PHYS_64BIT is not set
+CONFIG_SPE=y
+# CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+CONFIG_PPC_UDBG_16550=y
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+CONFIG_DEFAULT_UIMAGE=y
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLUB_DEBUG=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_KPROBES=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+# CONFIG_MODULES is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_CLASSIC_RCU=y
+# CONFIG_PREEMPT_RCU is not set
+
+#
+# Platform support
+#
+# CONFIG_PPC_MPC512x is not set
+# CONFIG_PPC_MPC5121 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+CONFIG_MPC85xx=y
+# CONFIG_MPC8540_ADS is not set
+# CONFIG_MPC8560_ADS is not set
+# CONFIG_MPC85xx_CDS is not set
+# CONFIG_MPC85xx_MDS is not set
+# CONFIG_MPC85xx_DS is not set
+CONFIG_KSI8560=y
+# CONFIG_STX_GP3 is not set
+# CONFIG_TQM8540 is not set
+# CONFIG_TQM8541 is not set
+# CONFIG_TQM8555 is not set
+# CONFIG_TQM8560 is not set
+# CONFIG_SBC8548 is not set
+# CONFIG_SBC8560 is not set
+# CONFIG_IPIC is not set
+CONFIG_MPIC=y
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+CONFIG_CPM2=y
+CONFIG_PPC_CPM_NEW_BINDING=y
+# CONFIG_FSL_ULI1575 is not set
+CONFIG_CPM=y
+
+#
+# Kernel options
+#
+CONFIG_HIGHMEM=y
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+# CONFIG_SCHED_HRTICK is not set
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_RCU_TRACE=y
+CONFIG_BINFMT_ELF=y
+CONFIG_BINFMT_MISC=y
+CONFIG_MATH_EMULATION=y
+# CONFIG_IOMMU_HELPER is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+# CONFIG_PROC_DEVICETREE is not set
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+# CONFIG_SECCOMP is not set
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_FSL_SOC=y
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0xc0000000
+CONFIG_BOOT_LOAD=0x00800000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=32768
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_EEPROM_93CX6 is not set
+CONFIG_IDE=y
+CONFIG_IDE_MAX_HWIFS=4
+CONFIG_BLK_DEV_IDE=y
+
+#
+# Please see Documentation/ide.txt for help/info on IDE drives
+#
+# CONFIG_BLK_DEV_IDE_SATA is not set
+# CONFIG_BLK_DEV_IDEDISK is not set
+# CONFIG_IDEDISK_MULTI_MODE is not set
+# CONFIG_BLK_DEV_IDECD is not set
+# CONFIG_BLK_DEV_IDETAPE is not set
+# CONFIG_BLK_DEV_IDEFLOPPY is not set
+# CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_PROC_FS=y
+
+#
+# IDE chipset support/bugfixes
+#
+CONFIG_IDE_GENERIC=y
+# CONFIG_BLK_DEV_PLATFORM is not set
+# CONFIG_BLK_DEV_IDEDMA is not set
+CONFIG_IDE_ARCH_OBSOLETE_INIT=y
+# CONFIG_BLK_DEV_HD is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+CONFIG_MARVELL_PHY=y
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_REALTEK_PHY is not set
+# CONFIG_FIXED_PHY is not set
+CONFIG_MDIO_BITBANG=y
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_B44 is not set
+CONFIG_FS_ENET=y
+# CONFIG_FS_ENET_HAS_SCC is not set
+CONFIG_FS_ENET_HAS_FCC=y
+CONFIG_FS_ENET_MDIO_FCC=y
+CONFIG_NETDEV_1000=y
+# CONFIG_E1000E_ENABLED is not set
+CONFIG_GIANFAR=y
+CONFIG_GFAR_NAPI=y
+CONFIG_NETDEV_10000=y
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_CPM=y
+CONFIG_SERIAL_CPM_CONSOLE=y
+CONFIG_SERIAL_CPM_SCC1=y
+# CONFIG_SERIAL_CPM_SCC2 is not set
+# CONFIG_SERIAL_CPM_SCC3 is not set
+# CONFIG_SERIAL_CPM_SCC4 is not set
+# CONFIG_SERIAL_CPM_SMC1 is not set
+# CONFIG_SERIAL_CPM_SMC2 is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=y
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+# CONFIG_HIDRAW is not set
+CONFIG_USB_SUPPORT=y
+# CONFIG_USB_ARCH_HAS_HCD is not set
+# CONFIG_USB_ARCH_HAS_OHCI is not set
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+# CONFIG_USB_GADGET is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4DEV_FS is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS2_FS is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+# CONFIG_NFS_V3 is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+# CONFIG_MSDOS_PARTITION is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+# CONFIG_NLS is not set
+# CONFIG_DLM is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+CONFIG_DEBUG_FS=y
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+CONFIG_DEBUG_MUTEXES=y
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_HIGHMEM is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_KGDB_CONSOLE is not set
+# CONFIG_VIRQ_DEBUG is not set
+# CONFIG_BDI_SWITCH is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+# CONFIG_CRYPTO_SEQIV is not set
+# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_MD4 is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_WP512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_XTS is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_LZO is not set
+CONFIG_CRYPTO_HW=y
+# CONFIG_PPC_CLOCK is not set
+CONFIG_PPC_LIB_RHEAP=y
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH 3/4] Emerson KSI8560 device tree
2008-03-04 16:23 [PATCH 0/4] Add Emerson KSI8560 board support Alexandr Smirnov
` (3 preceding siblings ...)
2008-03-04 16:36 ` [PATCH 4/4] Emerson KSI8560 default config Alexandr Smirnov
@ 2008-03-06 15:14 ` Alexandr Smirnov
2008-03-07 0:29 ` David Gibson
2008-03-07 15:10 ` Kumar Gala
2008-03-06 15:17 ` [PATCH 1/4] Emerson KSI8560 base support Alexandr Smirnov
5 siblings, 2 replies; 17+ messages in thread
From: Alexandr Smirnov @ 2008-03-06 15:14 UTC (permalink / raw)
To: linuxppc-dev
Add device tree file for Emerson KSI8560 board.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
b/arch/powerpc/boot/dts/ksi8560.dts | 264 ++++++++++++++++++++++++++++++++++++
1 file changed, 264 insertions(+)
diff --git a/arch/powerpc/boot/dts/ksi8560.dts b/arch/powerpc/boot/dts/ksi8560.dts
new file mode 100644
index 0000000..78d26f4
--- /dev/null
+++ b/arch/powerpc/boot/dts/ksi8560.dts
@@ -0,0 +1,264 @@
+/*
+ * Device Tree Source for Emerson KSI8560
+ *
+ * Author: Alexandr Smirnov <asmirnov@ru.mvista.com>
+ *
+ * Based on mpc8560ads.dts
+ *
+ * 2008 (c) MontaVista, Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ *
+ */
+
+/dts-v1/;
+
+/ {
+ model = "KSI8560";
+ compatible = "emerson,KSI8560";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ aliases {
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,8560@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <32>;
+ i-cache-line-size = <32>;
+ d-cache-size = <0x8000>; /* L1, 32K */
+ i-cache-size = <0x8000>; /* L1, 32K */
+ timebase-frequency = <0>; /* From U-boot */
+ bus-frequency = <0>; /* From U-boot */
+ clock-frequency = <0>; /* From U-boot */
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x10000000>; /* Fixed by bootwrapper */
+ };
+
+ soc@fdf00000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ ranges = <0x00000000 0xfdf00000 0x00100000>;
+ bus-frequency = <0>; /* Fixed by bootwrapper */
+
+ memory-controller@2000 {
+ compatible = "fsl,8540-memory-controller";
+ reg = <0x2000 0x1000>;
+ interrupt-parent = <&MPIC>;
+ interrupts = <0x12 0x2>;
+ };
+
+ l2-cache-controller@20000 {
+ compatible = "fsl,8540-l2-cache-controller";
+ reg = <0x20000 0x1000>;
+ cache-line-size = <0x20>; /* 32 bytes */
+ cache-size = <0x40000>; /* L2, 256K */
+ interrupt-parent = <&MPIC>;
+ interrupts = <0x10 0x2>;
+ };
+
+ i2c@3000 {
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <0x2b 0x2>;
+ interrupt-parent = <&MPIC>;
+ dfsrr;
+ };
+
+ mdio@24520 { /* For TSECs */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+
+ PHY1: ethernet-phy@1 {
+ interrupt-parent = <&MPIC>;
+ reg = <0x1>;
+ device_type = "ethernet-phy";
+ };
+
+ PHY2: ethernet-phy@2 {
+ interrupt-parent = <&MPIC>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ enet0: ethernet@24000 {
+ device_type = "network";
+ model = "TSEC";
+ compatible = "gianfar";
+ reg = <0x24000 0x1000>;
+ /* Mac address filled in by bootwrapper */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>;
+ interrupt-parent = <&MPIC>;
+ phy-handle = <&PHY1>;
+ };
+
+ enet1: ethernet@25000 {
+ device_type = "network";
+ model = "TSEC";
+ compatible = "gianfar";
+ reg = <0x25000 0x1000>;
+ /* Mac address filled in by bootwrapper */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <0x23 0x2 0x24 0x2 0x28 0x2>;
+ interrupt-parent = <&MPIC>;
+ phy-handle = <&PHY2>;
+ };
+
+ MPIC: pic@40000 {
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ reg = <0x40000 0x40000>;
+ device_type = "open-pic";
+ };
+
+ cpm@919c0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8560-cpm", "fsl,cpm2";
+ reg = <0x919c0 0x30>;
+ ranges;
+
+ muram@80000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x80000 0x10000>;
+
+ data@0 {
+ compatible = "fsl,cpm-muram-data";
+ reg = <0x0 0x4000 0x9000 0x2000>;
+ };
+ };
+
+ brg@919f0 {
+ compatible = "fsl,mpc8560-brg",
+ "fsl,cpm2-brg",
+ "fsl,cpm-brg";
+ reg = <0x919f0 0x10 0x915f0 0x10>;
+ clock-frequency = <165000000>; /* 166MHz */
+ };
+
+ CPMPIC: pic@90c00 {
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ interrupts = <0x2e 0x2>;
+ interrupt-parent = <&MPIC>;
+ reg = <0x90c00 0x80>;
+ compatible = "fsl,mpc8560-cpm-pic", "fsl,cpm2-pic";
+ };
+
+ serial@91a00 {
+ device_type = "serial";
+ compatible = "fsl,mpc8560-scc-uart",
+ "fsl,cpm2-scc-uart";
+ reg = <0x91a00 0x20 0x88000 0x100>;
+ fsl,cpm-brg = <1>;
+ fsl,cpm-command = <0x800000>;
+ current-speed = <0x1c200>;
+ interrupts = <0x28 0x8>;
+ interrupt-parent = <&CPMPIC>;
+ };
+
+ serial@91a20 {
+ device_type = "serial";
+ compatible = "fsl,mpc8560-scc-uart",
+ "fsl,cpm2-scc-uart";
+ reg = <0x91a20 0x20 0x88100 0x100>;
+ fsl,cpm-brg = <2>;
+ fsl,cpm-command = <0x4a00000>;
+ current-speed = <0x1c200>;
+ interrupts = <0x29 0x8>;
+ interrupt-parent = <&CPMPIC>;
+ };
+
+ mdio@90d00 { /* For FCCs */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,cpm2-mdio-bitbang";
+ reg = <0x90d00 0x14>;
+ fsl,mdio-pin = <24>;
+ fsl,mdc-pin = <25>;
+
+ PHY0: ethernet-phy@0 {
+ interrupt-parent = <&MPIC>;
+ reg = <0x0>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ enet2: ethernet@91300 {
+ device_type = "network";
+ compatible = "fsl,mpc8560-fcc-enet",
+ "fsl,cpm2-fcc-enet";
+ reg = <0x91300 0x20 0x88400 0x100 0x91390 0x1>;
+ /* Mac address filled in by bootwrapper */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ fsl,cpm-command = <0x12000300>;
+ interrupts = <0x20 0x8>;
+ interrupt-parent = <&CPMPIC>;
+ phy-handle = <&PHY0>;
+ };
+ };
+ };
+
+ localbus@fdf05000 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8560-localbus";
+ reg = <0xfdf05000 0x68>;
+
+ ranges = <0x0 0x0 0xe0000000 0x00800000
+ 0x4 0x0 0xe8080000 0x00080000>;
+
+ flash@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec-flash";
+ reg = <0x0 0x0 0x800000>;
+ bank-width = <0x2>;
+
+ partition@0 {
+ label = "Primary Kernel";
+ reg = <0x0 0x180000>;
+ };
+ partition@180000 {
+ label = "Primary Filesystem";
+ reg = <0x180000 0x580000>;
+ };
+ partition@700000 {
+ label = "Monitor";
+ reg = <0x300000 0x100000>;
+ read-only;
+ };
+ };
+
+ cpld@4,0 {
+ compatible = "emerson,KSI8560-cpld";
+ reg = <0x4 0x0 0x80000>;
+ };
+ };
+
+
+ chosen {
+ linux,stdout-path = "/soc/cpm/serial@91a00";
+ };
+};
^ permalink raw reply related [flat|nested] 17+ messages in thread* Re: [PATCH 3/4] Emerson KSI8560 device tree
2008-03-06 15:14 ` [PATCH 3/4] Emerson KSI8560 device tree Alexandr Smirnov
@ 2008-03-07 0:29 ` David Gibson
2008-03-07 1:57 ` Olof Johansson
2008-03-07 15:10 ` Kumar Gala
1 sibling, 1 reply; 17+ messages in thread
From: David Gibson @ 2008-03-07 0:29 UTC (permalink / raw)
To: Alexandr Smirnov; +Cc: linuxppc-dev
On Thu, Mar 06, 2008 at 06:14:51PM +0300, Alexandr Smirnov wrote:
> Add device tree file for Emerson KSI8560 board.
>
> Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
[snip]
> + soc@fdf00000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + device_type = "soc";
Since this is a new board, is it feasible to require it to have a
sufficient new u-boot version that we don't require this old
device_type entry.
--
David Gibson | I'll have my music baroque, and my code
david AT gibson.dropbear.id.au | minimalist, thank you. NOT _the_ _other_
| _way_ _around_!
http://www.ozlabs.org/~dgibson
^ permalink raw reply [flat|nested] 17+ messages in thread* Re: [PATCH 3/4] Emerson KSI8560 device tree
2008-03-07 0:29 ` David Gibson
@ 2008-03-07 1:57 ` Olof Johansson
0 siblings, 0 replies; 17+ messages in thread
From: Olof Johansson @ 2008-03-07 1:57 UTC (permalink / raw)
To: Alexandr Smirnov, linuxppc-dev
On Fri, Mar 07, 2008 at 11:29:59AM +1100, David Gibson wrote:
> On Thu, Mar 06, 2008 at 06:14:51PM +0300, Alexandr Smirnov wrote:
> > Add device tree file for Emerson KSI8560 board.
> >
> > Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
>
> [snip]
> > + soc@fdf00000 {
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + device_type = "soc";
>
> Since this is a new board, is it feasible to require it to have a
> sufficient new u-boot version that we don't require this old
> device_type entry.
Here's a novel idea:
What if the device tree police spent a little more time on fixing up
existing DTS files and booting-without-of.txt, and a little less time
making it as hard as possible for people to get new board ports in?
That way, at least they would be demanding of new submissions what is
documented and already accepted.
Current booting-without-of.txt still claims that /soc should have
device_type "soc".
-Olof
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 3/4] Emerson KSI8560 device tree
2008-03-06 15:14 ` [PATCH 3/4] Emerson KSI8560 device tree Alexandr Smirnov
2008-03-07 0:29 ` David Gibson
@ 2008-03-07 15:10 ` Kumar Gala
1 sibling, 0 replies; 17+ messages in thread
From: Kumar Gala @ 2008-03-07 15:10 UTC (permalink / raw)
To: Alexandr Smirnov; +Cc: linuxppc-dev
On Mar 6, 2008, at 9:14 AM, Alexandr Smirnov wrote:
> Add device tree file for Emerson KSI8560 board.
>
> Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
>
> b/arch/powerpc/boot/dts/ksi8560.dts | 264 ++++++++++++++++++++++++++
> ++++++++++
> 1 file changed, 264 insertions(+)
Fixed up i2c to add #address-cells, #size-cells and cell-idnex
applied to powerpc-next.
- k
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PATCH 1/4] Emerson KSI8560 base support
2008-03-04 16:23 [PATCH 0/4] Add Emerson KSI8560 board support Alexandr Smirnov
` (4 preceding siblings ...)
2008-03-06 15:14 ` [PATCH 3/4] Emerson KSI8560 device tree Alexandr Smirnov
@ 2008-03-06 15:17 ` Alexandr Smirnov
2008-03-07 15:07 ` Kumar Gala
5 siblings, 1 reply; 17+ messages in thread
From: Alexandr Smirnov @ 2008-03-06 15:17 UTC (permalink / raw)
To: linuxppc-dev
The KSI8560 is a single compact, mid-, or full-size Advanced Mezzanine Card
(AdvancedMC™) based on the Freescale™ Semiconductor MPC8560 PowerQUICC III™
microprocessor. This product will serve in data and signaling applications such
as signaling gateways (SGW) and softswitch signaling interface cards.
The board has altera maxii CPLD, that is used to obtain and manage board
configuration. Also there are two SCC UART serial consoles and FCC ethernet,
that is routed to the front panel, while other ethernet controlers (TSEC's) are
routed to the backplane.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
arch/powerpc/platforms/85xx/Kconfig | 7
arch/powerpc/platforms/85xx/Makefile | 1
arch/powerpc/platforms/85xx/ksi8560.c | 257 ++++++++++++++++++++++++++++++++++
3 files changed, 265 insertions(+)
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index 7e76ddb..28bc6e5 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -46,6 +46,13 @@ config MPC85xx_DS
help
This option enables support for the MPC85xx DS (MPC8544 DS) board
+config KSI8560
+ bool "Emerson KSI8560"
+ select PPC_CPM_NEW_BINDING
+ select DEFAULT_UIMAGE
+ help
+ This option enables support for the Emerson KSI8560 board
+
config STX_GP3
bool "Silicon Turnkey Express GP3"
help
diff --git a/arch/powerpc/platforms/85xx/Makefile b/arch/powerpc/platforms/85xx/Makefile
index cb7af4e..6cea185 100644
--- a/arch/powerpc/platforms/85xx/Makefile
+++ b/arch/powerpc/platforms/85xx/Makefile
@@ -10,3 +10,4 @@ obj-$(CONFIG_STX_GP3) += stx_gp3.o
obj-$(CONFIG_TQM85xx) += tqm85xx.o
obj-$(CONFIG_SBC8560) += sbc8560.o
obj-$(CONFIG_SBC8548) += sbc8548.o
+obj-$(CONFIG_KSI8560) += ksi8560.o
diff --git a/arch/powerpc/platforms/85xx/ksi8560.c b/arch/powerpc/platforms/85xx/ksi8560.c
new file mode 100644
index 0000000..b3b8194
--- /dev/null
+++ b/arch/powerpc/platforms/85xx/ksi8560.c
@@ -0,0 +1,257 @@
+/*
+ * Board setup routines for the Emerson KSI8560
+ *
+ * Author: Alexandr Smirnov <asmirnov@ru.mvista.com>
+ *
+ * Based on mpc85xx_ads.c maintained by Kumar Gala
+ *
+ * 2008 (c) MontaVista, Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ *
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/kdev_t.h>
+#include <linux/delay.h>
+#include <linux/seq_file.h>
+#include <linux/of_platform.h>
+
+#include <asm/system.h>
+#include <asm/time.h>
+#include <asm/machdep.h>
+#include <asm/pci-bridge.h>
+#include <asm/mpic.h>
+#include <mm/mmu_decl.h>
+#include <asm/udbg.h>
+#include <asm/prom.h>
+
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+
+#include <asm/cpm2.h>
+#include <sysdev/cpm2_pic.h>
+
+
+#define KSI8560_CPLD_HVR 0x04 /* Hardware Version Register */
+#define KSI8560_CPLD_PVR 0x08 /* PLD Version Register */
+#define KSI8560_CPLD_RCR1 0x30 /* Reset Command Register 1 */
+
+#define KSI8560_CPLD_RCR1_CPUHR 0x80 /* CPU Hard Reset */
+
+static void __iomem *cpld_base = NULL;
+
+static void machine_restart(char *cmd)
+{
+ if (cpld_base)
+ out_8(cpld_base + KSI8560_CPLD_RCR1, KSI8560_CPLD_RCR1_CPUHR);
+ else
+ printk(KERN_ERR "Can't find CPLD base, hang forever\n");
+
+ for (;;);
+}
+
+static void cpm2_cascade(unsigned int irq, struct irq_desc *desc)
+{
+ int cascade_irq;
+
+ while ((cascade_irq = cpm2_get_irq()) >= 0)
+ generic_handle_irq(cascade_irq);
+
+ desc->chip->eoi(irq);
+}
+
+static void __init ksi8560_pic_init(void)
+{
+ struct mpic *mpic;
+ struct resource r;
+ struct device_node *np;
+#ifdef CONFIG_CPM2
+ int irq;
+#endif
+
+ np = of_find_node_by_type(NULL, "open-pic");
+
+ if (np == NULL) {
+ printk(KERN_ERR "Could not find open-pic node\n");
+ return;
+ }
+
+ if (of_address_to_resource(np, 0, &r)) {
+ printk(KERN_ERR "Could not map mpic register space\n");
+ of_node_put(np);
+ return;
+ }
+
+ mpic = mpic_alloc(np, r.start,
+ MPIC_PRIMARY | MPIC_WANTS_RESET | MPIC_BIG_ENDIAN,
+ 0, 256, " OpenPIC ");
+ BUG_ON(mpic == NULL);
+ of_node_put(np);
+
+ mpic_init(mpic);
+
+#ifdef CONFIG_CPM2
+ /* Setup CPM2 PIC */
+ np = of_find_compatible_node(NULL, NULL, "fsl,cpm2-pic");
+ if (np == NULL) {
+ printk(KERN_ERR "PIC init: can not find fsl,cpm2-pic node\n");
+ return;
+ }
+ irq = irq_of_parse_and_map(np, 0);
+
+ cpm2_pic_init(np);
+ of_node_put(np);
+ set_irq_chained_handler(irq, cpm2_cascade);
+
+ setup_irq(0, NULL);
+#endif
+}
+
+#ifdef CONFIG_CPM2
+/*
+ * Setup I/O ports
+ */
+struct cpm_pin {
+ int port, pin, flags;
+};
+
+static struct cpm_pin __initdata ksi8560_pins[] = {
+ /* SCC1 */
+ {3, 29, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {3, 30, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {3, 31, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+
+ /* SCC2 */
+ {3, 26, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {3, 27, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {3, 28, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+
+ /* FCC1 */
+ {0, 14, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 15, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 16, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 17, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 18, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 19, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 20, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 21, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 26, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {0, 27, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {0, 28, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {0, 29, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {0, 30, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {0, 31, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {2, 23, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, /* CLK9 */
+ {2, 22, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, /* CLK10 */
+
+};
+
+static void __init init_ioports(void)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(ksi8560_pins); i++) {
+ struct cpm_pin *pin = &ksi8560_pins[i];
+ cpm2_set_pin(pin->port, pin->pin, pin->flags);
+ }
+
+ cpm2_clk_setup(CPM_CLK_SCC1, CPM_BRG1, CPM_CLK_RX);
+ cpm2_clk_setup(CPM_CLK_SCC1, CPM_BRG1, CPM_CLK_TX);
+ cpm2_clk_setup(CPM_CLK_SCC2, CPM_BRG2, CPM_CLK_RX);
+ cpm2_clk_setup(CPM_CLK_SCC2, CPM_BRG2, CPM_CLK_TX);
+ cpm2_clk_setup(CPM_CLK_FCC1, CPM_CLK9, CPM_CLK_RX);
+ cpm2_clk_setup(CPM_CLK_FCC1, CPM_CLK10, CPM_CLK_TX);
+}
+#endif
+
+/*
+ * Setup the architecture
+ */
+static void __init ksi8560_setup_arch(void)
+{
+ struct device_node *cpld;
+
+ cpld = of_find_compatible_node(NULL, NULL, "emerson,KSI8560-cpld");
+ if (cpld)
+ cpld_base = of_iomap(cpld, 0);
+ else
+ printk(KERN_ERR "Can't find CPLD in device tree\n");
+
+ if (ppc_md.progress)
+ ppc_md.progress("ksi8560_setup_arch()", 0);
+
+#ifdef CONFIG_CPM2
+ cpm2_reset();
+ init_ioports();
+#endif
+}
+
+static void ksi8560_show_cpuinfo(struct seq_file *m)
+{
+ uint pvid, svid, phid1;
+ uint memsize = total_memory;
+
+ pvid = mfspr(SPRN_PVR);
+ svid = mfspr(SPRN_SVR);
+
+ seq_printf(m, "Vendor\t\t: Emerson Network Power\n");
+ seq_printf(m, "Board\t\t: KSI8560\n");
+
+ if (cpld_base) {
+ seq_printf(m, "Hardware rev\t: %d\n",
+ in_8(cpld_base + KSI8560_CPLD_HVR));
+ seq_printf(m, "CPLD rev\t: %d\n",
+ in_8(cpld_base + KSI8560_CPLD_PVR));
+ } else
+ seq_printf(m, "Unknown Hardware and CPLD revs\n");
+
+ seq_printf(m, "PVR\t\t: 0x%x\n", pvid);
+ seq_printf(m, "SVR\t\t: 0x%x\n", svid);
+
+ /* Display cpu Pll setting */
+ phid1 = mfspr(SPRN_HID1);
+ seq_printf(m, "PLL setting\t: 0x%x\n", ((phid1 >> 24) & 0x3f));
+
+ /* Display the amount of memory */
+ seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
+}
+
+static struct of_device_id __initdata of_bus_ids[] = {
+ { .type = "soc", },
+ { .name = "cpm", },
+ { .name = "localbus", },
+ {},
+};
+
+static int __init declare_of_platform_devices(void)
+{
+ of_platform_bus_probe(NULL, of_bus_ids, NULL);
+
+ return 0;
+}
+machine_device_initcall(ksi8560, declare_of_platform_devices);
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init ksi8560_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+
+ return of_flat_dt_is_compatible(root, "emerson,KSI8560");
+}
+
+define_machine(ksi8560) {
+ .name = "KSI8560",
+ .probe = ksi8560_probe,
+ .setup_arch = ksi8560_setup_arch,
+ .init_IRQ = ksi8560_pic_init,
+ .show_cpuinfo = ksi8560_show_cpuinfo,
+ .get_irq = mpic_get_irq,
+ .restart = machine_restart,
+ .calibrate_decr = generic_calibrate_decr,
+};
^ permalink raw reply related [flat|nested] 17+ messages in thread* Re: [PATCH 1/4] Emerson KSI8560 base support
2008-03-06 15:17 ` [PATCH 1/4] Emerson KSI8560 base support Alexandr Smirnov
@ 2008-03-07 15:07 ` Kumar Gala
0 siblings, 0 replies; 17+ messages in thread
From: Kumar Gala @ 2008-03-07 15:07 UTC (permalink / raw)
To: Alexandr Smirnov; +Cc: linuxppc-dev
On Mar 6, 2008, at 9:17 AM, Alexandr Smirnov wrote:
> The KSI8560 is a single compact, mid-, or full-size Advanced =20
> Mezzanine Card
> (AdvancedMC=99) based on the Freescale=99 Semiconductor MPC8560 =20
> PowerQUICC III=99
> microprocessor. This product will serve in data and signaling =20
> applications such
> as signaling gateways (SGW) and softswitch signaling interface cards.
>
> The board has altera maxii CPLD, that is used to obtain and manage =20
> board
> configuration. Also there are two SCC UART serial consoles and FCC =20
> ethernet,
> that is routed to the front panel, while other ethernet controlers =20
> (TSEC's) are
> routed to the backplane.
>
> Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
>
> arch/powerpc/platforms/85xx/Kconfig | 7
> arch/powerpc/platforms/85xx/Makefile | 1
> arch/powerpc/platforms/85xx/ksi8560.c | 257 ++++++++++++++++++++++++=20=
> ++++++++++
> 3 files changed, 265 insertions(+)
applied to powerpc-next.
- k
^ permalink raw reply [flat|nested] 17+ messages in thread