LinuxPPC-Dev Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Sebastian Siewior <bigeasy@linutronix.de>
To: Greg Kroah-Hartman <gregkh@suse.de>
Cc: linuxppc-dev@ozlabs.org, Thomas Gleixner <tglx@linutronix.de>,
	linux-usb@vger.kernel.org
Subject: [PATCH / RFC 2/2] ISP1760: bus glue code
Date: Tue, 01 Apr 2008 21:52:11 +0200	[thread overview]
Message-ID: <20080401195342.059470799@linutronix.de> (raw)
In-Reply-To: 20080401195158.657955430@linutronix.de

This patch contains the entry for the build system and glue code for the
platform bus. Currently OpenFirmware and PCI is supported.

Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -95,6 +95,32 @@ config USB_ISP116X_HCD
 	  To compile this driver as a module, choose M here: the
 	  module will be called isp116x-hcd.
 
+config USB_ISP1760_HCD
+	tristate "ISP 1760 HCD support"
+	depends on USB && EXPERIMENTAL
+	---help---
+	  The ISP1760 chip is a USB 2.0 host controller.
+
+	  This driver does not support isochronous transfers or OTG.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called isp1760-hcd.
+
+config USB_ISP1760_PCI
+	bool "Support for the PCI bus"
+	depends on USB_ISP1760_HCD && PCI
+	---help---
+	  Enables support for the device present on the PCI bus.
+	  This should only be required if you happen to have the eval kit from
+	  NXP and you are going to test it.
+
+config USB_ISP1760_OF
+	bool "Support for the OF platform bus"
+	depends on USB_ISP1760_HCD && OF
+	---help---
+	  Enables support for the device present on the PowerPC
+	  OpenFirmware platform bus.
+
 config USB_OHCI_HCD
 	tristate "OHCI HCD support"
 	depends on USB && USB_ARCH_HAS_OHCI
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -6,6 +6,8 @@ ifeq ($(CONFIG_USB_DEBUG),y)
 	EXTRA_CFLAGS		+= -DDEBUG
 endif
 
+isp1760-objs := isp1760-hcd.o isp1760-if.o
+
 obj-$(CONFIG_PCI)		+= pci-quirks.o
 
 obj-$(CONFIG_USB_EHCI_HCD)	+= ehci-hcd.o
@@ -16,4 +18,4 @@ obj-$(CONFIG_USB_SL811_HCD)	+= sl811-hcd
 obj-$(CONFIG_USB_SL811_CS)	+= sl811_cs.o
 obj-$(CONFIG_USB_U132_HCD)	+= u132-hcd.o
 obj-$(CONFIG_USB_R8A66597_HCD)	+= r8a66597-hcd.o
-
+obj-$(CONFIG_USB_ISP1760_HCD)	+= isp1760.o
--- /dev/null
+++ b/drivers/usb/host/isp1760-if.c
@@ -0,0 +1,294 @@
+/*
+ * Glue code for the ISP1760 driver and bus
+ * Currently there is support for
+ * - OpenFirmware
+ * - PCI
+ *
+ * (c) 2007 Sebastian Siewior <bigeasy@linutronix.de>
+ *
+ */
+
+#include <linux/usb.h>
+#include <linux/io.h>
+
+#include "../core/hcd.h"
+#include "isp1760-hcd.h"
+
+#ifdef CONFIG_USB_ISP1760_OF
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#endif
+
+#ifdef CONFIG_USB_ISP1760_PCI
+#include <linux/pci.h>
+#endif
+
+#ifdef CONFIG_USB_ISP1760_OF
+static int of_isp1760_probe(struct of_device *dev,
+		const struct of_device_id *match)
+{
+	struct usb_hcd *hcd;
+	struct device_node *dp = dev->node;
+	struct resource *res;
+	struct resource memory;
+	struct of_irq oirq;
+	int virq;
+	u64 res_len;
+	int ret;
+
+	ret = of_address_to_resource(dp, 0, &memory);
+	if (ret)
+		return -ENXIO;
+
+	res = request_mem_region(memory.start, memory.end - memory.start + 1,
+			dev->dev.bus_id);
+	if (!res)
+		return -EBUSY;
+
+	res_len = memory.end - memory.start + 1;
+
+	if (of_irq_map_one(dp, 0, &oirq)) {
+		ret = -ENODEV;
+		goto release_reg;
+	}
+
+	virq = irq_create_of_mapping(oirq.controller, oirq.specifier,
+			oirq.size);
+
+	hcd = isp1760_register(memory.start, res_len, virq,
+		IRQF_SHARED | IRQF_DISABLED, &dev->dev, dev->dev.bus_id);
+	if (IS_ERR(hcd)) {
+		ret = PTR_ERR(hcd);
+		goto release_reg;
+	}
+
+	dev_set_drvdata(&dev->dev, hcd);
+	return ret;
+
+release_reg:
+	release_mem_region(memory.start, memory.end - memory.start + 1);
+	return ret;
+}
+
+static int of_isp1760_remove(struct of_device *dev)
+{
+	struct usb_hcd *hcd = dev_get_drvdata(&dev->dev);
+
+	dev_set_drvdata(&dev->dev, NULL);
+
+	usb_remove_hcd(hcd);
+	iounmap(hcd->regs);
+	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+	usb_put_hcd(hcd);
+	return 0;
+}
+
+static struct of_device_id of_isp1760_match[] = {
+	{
+		.compatible = "nxp,usb-isp1760",
+	},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, of_isp1760_match);
+
+static struct of_platform_driver isp1760_of_driver = {
+	.name           = "nxp-isp1760",
+	.match_table    = of_isp1760_match,
+	.probe          = of_isp1760_probe,
+	.remove         = of_isp1760_remove,
+};
+#endif
+
+#ifdef CONFIG_USB_ISP1760_PCI
+static u32 nxp_pci_io_base;
+static u32 iolength;
+static u32 pci_mem_phy0;
+static u32 length;
+static u8 *chip_addr;
+static u8 *iobase;
+
+static int __devinit isp1761_pci_probe(struct pci_dev *dev,
+		const struct pci_device_id *id)
+{
+	u8 latency, limit;
+	__u32 reg_data;
+	int retry_count;
+	int length;
+	int status = 1;
+	struct usb_hcd *hcd;
+
+	if (usb_disabled())
+		return -ENODEV;
+
+	if (pci_enable_device(dev) < 0)
+		return -ENODEV;
+
+	if (!dev->irq)
+		return -ENODEV;
+
+	/* Grab the PLX PCI mem maped port start address we need  */
+	nxp_pci_io_base = pci_resource_start(dev, 0);
+	iolength = pci_resource_len(dev, 0);
+
+	if (!request_mem_region(nxp_pci_io_base, iolength, "ISP1761 IO MEM")) {
+		printk(KERN_ERR "request region #1\n");
+		return -EBUSY;
+	}
+
+	iobase = ioremap_nocache(nxp_pci_io_base, iolength);
+	if (!iobase) {
+		printk(KERN_ERR "ioremap #1\n");
+		release_mem_region(nxp_pci_io_base, iolength);
+		return -ENOMEM;
+	}
+	/* Grab the PLX PCI shared memory of the ISP 1761 we need  */
+	pci_mem_phy0 = pci_resource_start(dev, 3);
+	length = pci_resource_len(dev, 3);
+
+	if (length < 0xffff) {
+		printk(KERN_ERR "memory length for this resource is less than "
+				"required\n");
+		release_mem_region(nxp_pci_io_base, iolength);
+		iounmap(iobase);
+		return  -ENOMEM;
+	}
+
+	if (!request_mem_region(pci_mem_phy0, length, "ISP-PCI")) {
+		printk(KERN_ERR "host controller already in use\n");
+		release_mem_region(nxp_pci_io_base, iolength);
+		iounmap(iobase);
+		return -EBUSY;
+	}
+
+	/* bad pci latencies can contribute to overruns */
+	pci_read_config_byte(dev, PCI_LATENCY_TIMER, &latency);
+	if (latency) {
+		pci_read_config_byte(dev, PCI_MAX_LAT, &limit);
+		if (limit && limit < latency)
+			pci_write_config_byte(dev, PCI_LATENCY_TIMER, limit);
+	}
+
+	/* Try to check whether we can access Scratch Register of
+	 * Host Controller or not. The initial PCI access is retried until
+	 * local init for the PCI bridge is completed
+	 */
+	retry_count = 20;
+	reg_data = 0;
+	while ((reg_data != 0xFACE) && retry_count) {
+		/*by default host is in 16bit mode, so
+		 * io operations at this stage must be 16 bit
+		 * */
+		writel(0xface, chip_addr + HC_SCRATCH_REG);
+		udelay(100);
+		reg_data = readl(chip_addr + HC_SCRATCH_REG);
+		retry_count--;
+	}
+
+	/* Host Controller presence is detected by writing to scratch register
+	 * and reading back and checking the contents are same or not
+	 */
+	if (reg_data != 0xFACE) {
+		err("scratch register mismatch %x", reg_data);
+		goto clean;
+	}
+
+	pci_set_master(dev);
+
+	status = readl(iobase + 0x68);
+	status |= 0x900;
+	writel(status, iobase + 0x68);
+
+	dev->dev.dma_mask = NULL;
+	hcd = isp1760_register(pci_mem_phy0, length, dev->irq,
+		IRQF_SHARED | IRQF_DISABLED, &dev->dev, dev->dev.bus_id);
+	pci_set_drvdata(dev, hcd);
+	if (!hcd)
+		return 0;
+clean:
+	status = -ENODEV;
+	iounmap(iobase);
+	release_mem_region(pci_mem_phy0, length);
+	release_mem_region(nxp_pci_io_base, iolength);
+	return status;
+}
+static void isp1761_pci_remove(struct pci_dev *dev)
+{
+	struct usb_hcd *hcd;
+
+	hcd = pci_get_drvdata(dev);
+
+	usb_remove_hcd(hcd);
+	iounmap(hcd->regs);
+	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+	usb_put_hcd(hcd);
+
+	pci_disable_device(dev);
+
+	iounmap(iobase);
+	iounmap(chip_addr);
+
+	release_mem_region(nxp_pci_io_base, iolength);
+	release_mem_region(pci_mem_phy0, length);
+}
+
+static void ips1761_pci_shutdown(struct pci_dev *dev)
+{
+	printk(KERN_ERR "ips1761_pci_shutdown\n");
+}
+
+static const struct pci_device_id ips1760_plx [] = { {
+	/* handle any USB 2.0 EHCI controller */
+	PCI_DEVICE_CLASS(((PCI_CLASS_BRIDGE_OTHER << 8) | (0x06 << 16)), ~0),
+		.driver_data = 0,
+},
+{ /* end: all zeroes */ }
+};
+MODULE_DEVICE_TABLE(pci, ips1760_plx);
+
+static struct pci_driver isp1761_pci_driver = {
+	.name =         "isp1760",
+	.id_table =     ips1760_plx,
+	.probe =        isp1761_pci_probe,
+	.remove =       isp1761_pci_remove,
+	.shutdown =     ips1761_pci_shutdown,
+};
+#endif
+
+static int __init isp1760_init(void)
+{
+	int ret;
+
+	init_kmem_once();
+
+#ifdef CONFIG_USB_ISP1760_OF
+	ret = of_register_platform_driver(&isp1760_of_driver);
+	if (ret) {
+		deinit_kmem_cache();
+		return ret;
+	}
+#endif
+
+#ifdef CONFIG_USB_ISP1760_PCI
+	ret = pci_register_driver(&isp1761_pci_driver);
+	if (ret) {
+#ifdef CONFIG_USB_ISP1760_OF
+	    of_unregister_platform_driver(&isp1760_of_driver);
+#endif
+	    deinit_kmem_cache();
+	}
+#endif
+	return ret;
+}
+module_init(isp1760_init);
+
+static void __exit isp1760_exit(void)
+{
+#ifdef CONFIG_USB_ISP1760_OF
+	of_unregister_platform_driver(&isp1760_of_driver);
+#endif
+#ifdef CONFIG_USB_ISP1760_PCI
+	pci_unregister_driver(&isp1761_pci_driver);
+#endif
+	deinit_kmem_cache();
+}
+module_exit(isp1760_exit);

-- 

           reply	other threads:[~2008-04-01 19:52 UTC|newest]

Thread overview: expand[flat|nested]  mbox.gz  Atom feed
 [parent not found: <20080401195158.657955430@linutronix.de>]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20080401195342.059470799@linutronix.de \
    --to=bigeasy@linutronix.de \
    --cc=gregkh@suse.de \
    --cc=linux-usb@vger.kernel.org \
    --cc=linuxppc-dev@ozlabs.org \
    --cc=tglx@linutronix.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox