* linux 2.6 hangs at __delay function on Viretx 4 board @ 2008-05-14 3:29 swamydp 2008-05-14 15:01 ` John Linn 2008-06-19 16:33 ` swamydp 0 siblings, 2 replies; 14+ messages in thread From: swamydp @ 2008-05-14 3:29 UTC (permalink / raw) To: linuxppc-embedded I am trying to boot linux 2.6 on HITECH virtex 4(fx60) board. Linux hangs at address 0xc00045ec which is in the __udelay function. I am using EDK 9.2i and gcc version 4.0.2 for compiling the kernel. The following is the boot message from the bootloader. loaded at: 00400000 0054E19C board data at: 0054C120 0054C19C relocated to: 00404064 004040E0 zimage at: 00404E55 0054B5B4 avail ram: 0054F000 02000000 Linux/PPC load: console=ttyS0,9600 console=tty0 root=/dev/sda2 Uncompressing Linux...done. Now booting the kernel Any help is greatly appreciated. I have run out of ideas to fix this. Thanks swamy -- View this message in context: http://www.nabble.com/linux-2.6-hangs-at-__delay-function-on-Viretx-4-board-tp17222725p17222725.html Sent from the linuxppc-embedded mailing list archive at Nabble.com. ^ permalink raw reply [flat|nested] 14+ messages in thread
* RE: linux 2.6 hangs at __delay function on Viretx 4 board 2008-05-14 3:29 linux 2.6 hangs at __delay function on Viretx 4 board swamydp @ 2008-05-14 15:01 ` John Linn 2008-05-16 14:56 ` swamydp 2008-06-19 16:33 ` swamydp 1 sibling, 1 reply; 14+ messages in thread From: John Linn @ 2008-05-14 15:01 UTC (permalink / raw) To: swamydp, linuxppc-embedded Hi Swamy, I have seen this sometime before I think, but don't remember why. I see that udelay depends on loops_per_jiffy, have you looked to see what value it is? Maybe it's garbage and some large value? Have you tried dumping the __log_buf to understand how far it got thru booting the kernel before it got hung? I assume you must be using xmd to load the image, you can also use it to dump the buffer. On another processor I have seen it get hung in the calibrate_delay call from the kernel if the interrupts or timer aren't working, but haven't ever seen that on the Powerpc. Thanks, John -----Original Message----- From: linuxppc-embedded-bounces+john.linn=3Dxilinx.com@ozlabs.org [mailto:linuxppc-embedded-bounces+john.linn=3Dxilinx.com@ozlabs.org] On Behalf Of swamydp Sent: Tuesday, May 13, 2008 9:29 PM To: linuxppc-embedded@ozlabs.org Subject: linux 2.6 hangs at __delay function on Viretx 4 board I am trying to boot linux 2.6 on HITECH virtex 4(fx60) board. Linux hangs at address 0xc00045ec which is in the __udelay function. I am using EDK 9.2i and gcc version 4.0.2 for compiling the kernel. The following is the boot message from the bootloader.=20 loaded at: 00400000 0054E19C board data at: 0054C120 0054C19C relocated to: 00404064 004040E0 zimage at: 00404E55 0054B5B4 avail ram: 0054F000 02000000 Linux/PPC load: console=3DttyS0,9600 console=3Dtty0 root=3D/dev/sda2 Uncompressing Linux...done. Now booting the kernel Any help is greatly appreciated. I have run out of ideas to fix this. Thanks swamy --=20 View this message in context: http://www.nabble.com/linux-2.6-hangs-at-__delay-function-on-Viretx-4-bo ard-tp17222725p17222725.html Sent from the linuxppc-embedded mailing list archive at Nabble.com. _______________________________________________ Linuxppc-embedded mailing list Linuxppc-embedded@ozlabs.org https://ozlabs.org/mailman/listinfo/linuxppc-embedded ^ permalink raw reply [flat|nested] 14+ messages in thread
* RE: linux 2.6 hangs at __delay function on Viretx 4 board 2008-05-14 15:01 ` John Linn @ 2008-05-16 14:56 ` swamydp 2008-05-16 16:28 ` John Linn 0 siblings, 1 reply; 14+ messages in thread From: swamydp @ 2008-05-16 14:56 UTC (permalink / raw) To: linuxppc-embedded John Thanks for your suggestions. I looked up the virtual address for __log_buf in System.map and subtracted 0xc0000000 to get the physical address. I then reset the processor from XMD and dump contents of the physical address of __log_buf using 'mrd' command from XMD. All I see is bunch of zeros in those locations. I am debugging but do not have much clue. Swamy John Linn wrote: > > Hi Swamy, > > I have seen this sometime before I think, but don't remember why. > > I see that udelay depends on loops_per_jiffy, have you looked to see > what value it is? Maybe it's garbage and some large value? > > Have you tried dumping the __log_buf to understand how far it got thru > booting the kernel before it got hung? > > I assume you must be using xmd to load the image, you can also use it to > dump the buffer. > > On another processor I have seen it get hung in the calibrate_delay call > from the kernel if the interrupts or timer aren't working, but haven't > ever seen that on the Powerpc. > > Thanks, > John > > > -----Original Message----- > From: linuxppc-embedded-bounces+john.linn=xilinx.com@ozlabs.org > [mailto:linuxppc-embedded-bounces+john.linn=xilinx.com@ozlabs.org] On > Behalf Of swamydp > Sent: Tuesday, May 13, 2008 9:29 PM > To: linuxppc-embedded@ozlabs.org > Subject: linux 2.6 hangs at __delay function on Viretx 4 board > > > > I am trying to boot linux 2.6 on HITECH virtex 4(fx60) board. Linux > hangs at > address 0xc00045ec which is in the __udelay function. I am using EDK > 9.2i > and gcc version 4.0.2 for compiling the kernel. The following is the > boot > message from the bootloader. > > loaded at: 00400000 0054E19C > board data at: 0054C120 0054C19C > relocated to: 00404064 004040E0 > zimage at: 00404E55 0054B5B4 > avail ram: 0054F000 02000000 > > Linux/PPC load: console=ttyS0,9600 console=tty0 root=/dev/sda2 > Uncompressing Linux...done. > Now booting the kernel > > Any help is greatly appreciated. I have run out of ideas to fix this. > > Thanks > swamy > > -- > View this message in context: > http://www.nabble.com/linux-2.6-hangs-at-__delay-function-on-Viretx-4-bo > ard-tp17222725p17222725.html > Sent from the linuxppc-embedded mailing list archive at Nabble.com. > > _______________________________________________ > Linuxppc-embedded mailing list > Linuxppc-embedded@ozlabs.org > https://ozlabs.org/mailman/listinfo/linuxppc-embedded > > > _______________________________________________ > Linuxppc-embedded mailing list > Linuxppc-embedded@ozlabs.org > https://ozlabs.org/mailman/listinfo/linuxppc-embedded > > -- View this message in context: http://www.nabble.com/linux-2.6-hangs-at-__delay-function-on-Viretx-4-board-tp17222725p17276753.html Sent from the linuxppc-embedded mailing list archive at Nabble.com. ^ permalink raw reply [flat|nested] 14+ messages in thread
* RE: linux 2.6 hangs at __delay function on Viretx 4 board 2008-05-16 14:56 ` swamydp @ 2008-05-16 16:28 ` John Linn 2008-05-25 5:35 ` swamydp 0 siblings, 1 reply; 14+ messages in thread From: John Linn @ 2008-05-16 16:28 UTC (permalink / raw) To: swamydp, linuxppc-embedded Swamy, Looks like the kernel is probably not running at all yet, may stuck in early initialization. 1. Has the kernel ever ran on this board or is this development to get it running? I have ran into issues with the memory being setup incorrectly (the end address/how much memory) and seen something similar to this. I would review the bootstrap loader output carefully to ensure the memory is setup correctly. 2. Not sure on the tools you are using to build it. You mention the EDK, but you must not be using it's compiler as it's not configured in the EDK to build Linux. = I use the ELDK 4.1 right now as we are still figuring out our tool situation. = 3. Without a good JTAG emulator, bring up can be painful in my experience. The EDK GDB/XMD is not fully MMU aware, so once the MMU is one it won't allow you to debug. If you have access to an MMU aware debugger that could help. I have used BDI 2000 for these type of problems and it helped. 4. In the absense of an MMU debugger, using the UART to slam bytes out of the serial port can help. The UART lite is easier for that as there's no setup required. The kernel can map an MMU TLB so that the UART is usable early, make sure that is setup in the early startup. Then I just use *(char *)<The UART xmt reg address> =3D <data byte> in the code to see what it's doing. 5. I would probably see where the udelay is called early in the kernel startup and why. I sometimes hack on it, comment stuff out, to get past it and figure out more data. Not always a good path, but can help. Good luck, John -----Original Message----- From: linuxppc-embedded-bounces+john.linn=3Dxilinx.com@ozlabs.org [mailto:linuxppc-embedded-bounces+john.linn=3Dxilinx.com@ozlabs.org] On Behalf Of swamydp Sent: Friday, May 16, 2008 8:57 AM To: linuxppc-embedded@ozlabs.org Subject: RE: linux 2.6 hangs at __delay function on Viretx 4 board John Thanks for your suggestions. I looked up the virtual address for __log_buf in System.map and subtracted 0xc0000000 to get the physical address. I then reset the processor from XMD and dump contents of the physical address of __log_buf using 'mrd' command from XMD. All I see is bunch of zeros in those locations. I am debugging but do not have much clue. Swamy John Linn wrote: > = > Hi Swamy, > = > I have seen this sometime before I think, but don't remember why. > = > I see that udelay depends on loops_per_jiffy, have you looked to see > what value it is? Maybe it's garbage and some large value? > = > Have you tried dumping the __log_buf to understand how far it got thru > booting the kernel before it got hung? > = > I assume you must be using xmd to load the image, you can also use it to > dump the buffer. > = > On another processor I have seen it get hung in the calibrate_delay call > from the kernel if the interrupts or timer aren't working, but haven't > ever seen that on the Powerpc. > = > Thanks, > John > = > = > -----Original Message----- > From: linuxppc-embedded-bounces+john.linn=3Dxilinx.com@ozlabs.org > [mailto:linuxppc-embedded-bounces+john.linn=3Dxilinx.com@ozlabs.org] On > Behalf Of swamydp > Sent: Tuesday, May 13, 2008 9:29 PM > To: linuxppc-embedded@ozlabs.org > Subject: linux 2.6 hangs at __delay function on Viretx 4 board > = > = > = > I am trying to boot linux 2.6 on HITECH virtex 4(fx60) board. Linux > hangs at > address 0xc00045ec which is in the __udelay function. I am using EDK > 9.2i > and gcc version 4.0.2 for compiling the kernel. The following is the > boot > message from the bootloader. = > = > loaded at: 00400000 0054E19C > board data at: 0054C120 0054C19C > relocated to: 00404064 004040E0 > zimage at: 00404E55 0054B5B4 > avail ram: 0054F000 02000000 > = > Linux/PPC load: console=3DttyS0,9600 console=3Dtty0 root=3D/dev/sda2 > Uncompressing Linux...done. > Now booting the kernel > = > Any help is greatly appreciated. I have run out of ideas to fix this. > = > Thanks > swamy > = > -- = > View this message in context: > http://www.nabble.com/linux-2.6-hangs-at-__delay-function-on-Viretx-4-bo > ard-tp17222725p17222725.html > Sent from the linuxppc-embedded mailing list archive at Nabble.com. > = > _______________________________________________ > Linuxppc-embedded mailing list > Linuxppc-embedded@ozlabs.org > https://ozlabs.org/mailman/listinfo/linuxppc-embedded > = > = > _______________________________________________ > Linuxppc-embedded mailing list > Linuxppc-embedded@ozlabs.org > https://ozlabs.org/mailman/listinfo/linuxppc-embedded > = > = -- = View this message in context: http://www.nabble.com/linux-2.6-hangs-at-__delay-function-on-Viretx-4-bo ard-tp17222725p17276753.html Sent from the linuxppc-embedded mailing list archive at Nabble.com. _______________________________________________ Linuxppc-embedded mailing list Linuxppc-embedded@ozlabs.org https://ozlabs.org/mailman/listinfo/linuxppc-embedded This email and any attachments are intended for the sole use of the named r= ecipient(s) and contain(s) confidential information that may be proprietary= , privileged or copyrighted under applicable law. If you are not the intend= ed recipient, do not read, copy, or forward this email message or any attac= hments. Delete this email message and any attachments immediately. ^ permalink raw reply [flat|nested] 14+ messages in thread
* RE: linux 2.6 hangs at __delay function on Viretx 4 board 2008-05-16 16:28 ` John Linn @ 2008-05-25 5:35 ` swamydp 2008-05-27 4:11 ` swamydp 0 siblings, 1 reply; 14+ messages in thread From: swamydp @ 2008-05-25 5:35 UTC (permalink / raw) To: linuxppc-embedded Hi John Sorry for getting back late. I have been debugging further using the UART to send output directly to serial post. Now I see that just after entering start_kernel, a ITLB miss exception occurs and linux hangs at that point. Looks like the kernel is probably not running at all yet, may stuck in early initialization. >> Yes 1. Has the kernel ever ran on this board or is this development to get it running? >> No. This is a new board and I am trying to build a simple EDK system with >> only PPC, UART, PIC as the devices. 2. Not sure on the tools you are using to build it. You mention the EDK, but you must not be using it's compiler as it's not configured in the EDK to build Linux. >> EDK 9.2 version, XMD for debug. Kernel 2.6 version is built in linux >> machine and zImage.elf is downloaded to the board. Thanks for the UART suggestion, works well. Any suggestions as to what might be wrong in start_kernel function ? I will continue debugging meanwhile. Thanks swamy -- View this message in context: http://www.nabble.com/linux-2.6-hangs-at-__delay-function-on-Viretx-4-board-tp17222725p17454696.html Sent from the linuxppc-embedded mailing list archive at Nabble.com. ^ permalink raw reply [flat|nested] 14+ messages in thread
* RE: linux 2.6 hangs at __delay function on Viretx 4 board 2008-05-25 5:35 ` swamydp @ 2008-05-27 4:11 ` swamydp 2008-05-28 14:07 ` John Linn 0 siblings, 1 reply; 14+ messages in thread From: swamydp @ 2008-05-27 4:11 UTC (permalink / raw) To: linuxppc-embedded Hi John Please ignore my previous message. The kernel boots until initializing the root files system and then hangs. Thats expected since I do not have root file system set up yet. I dumped the __log_buf and found it. I don't understand why no message is printed by printk after "Now booting". Does console init occur after root file system init ? Thanks swamy swamydp wrote: > > Hi John > > Sorry for getting back late. > > I have been debugging further using the UART to send output directly to > serial post. Now I see that just after entering start_kernel, a ITLB miss > exception occurs and linux hangs at that point. > > Looks like the kernel is probably not running at all yet, may stuck in > early initialization. > >>> Yes > > 1. Has the kernel ever ran on this board or is this development to get > it running? > >>> No. This is a new board and I am trying to build a simple EDK system >>> with only > PPC, UART, PIC as the devices. > > 2. Not sure on the tools you are using to build it. You mention the > EDK, but you must not be using it's compiler as it's not configured in > the EDK to build Linux. > >>> EDK 9.2 version, XMD for debug. Kernel 2.6 version is built in linux >>> machine and zImage.elf is downloaded > to the board. > > Thanks for the UART suggestion, works well. Any suggestions as to what > might be wrong in start_kernel function ? I will continue debugging > meanwhile. > > Thanks > swamy > > > > -- View this message in context: http://www.nabble.com/linux-2.6-hangs-at-__delay-function-on-Viretx-4-board-tp17222725p17482754.html Sent from the linuxppc-embedded mailing list archive at Nabble.com. ^ permalink raw reply [flat|nested] 14+ messages in thread
* RE: linux 2.6 hangs at __delay function on Viretx 4 board 2008-05-27 4:11 ` swamydp @ 2008-05-28 14:07 ` John Linn 2008-06-04 3:00 ` swamydp 0 siblings, 1 reply; 14+ messages in thread From: John Linn @ 2008-05-28 14:07 UTC (permalink / raw) To: swamydp, linuxppc-embedded Hi Swamy, Sorry for the long delay. Sounds like the console is not setup correctly. I notice in your command line it appears that you have 2 console statements. I have not tested this ever and I would change it to only have the console=3DttyS0,9600. I have seen other mailings, no Xilinx specific, related to this causing problems. This console setup assumes you're using the Xilinx 16550 UART. It could be an issue with the xparameters*.h file with the address of the UART. Have you compared your arch/ppc/platforms/4xx/xparameters/xparameters*.h file, whichever one it's setup to use, to the ones that we provided in the Git tree? I'm assuming you have the kernel configured correctly to use the UART16550 driver and the console is turned on, both are needed. The 16550 is 8250 compatible (mostly) and works with it's driver from Linux. CONFIG_SERIAL_8250=3Dy CONFIG_SERIAL_8250_CONSOLE=3Dy Thanks, John -----Original Message----- From: linuxppc-embedded-bounces+john.linn=3Dxilinx.com@ozlabs.org [mailto:linuxppc-embedded-bounces+john.linn=3Dxilinx.com@ozlabs.org] On Behalf Of swamydp Sent: Monday, May 26, 2008 10:12 PM To: linuxppc-embedded@ozlabs.org Subject: RE: linux 2.6 hangs at __delay function on Viretx 4 board Hi John Please ignore my previous message. The kernel boots until initializing the root files system and then hangs. Thats expected since I do not have root file system set up yet. I dumped the __log_buf and found it. = I don't understand why no message is printed by printk after "Now booting". Does console init occur after root file system init ? Thanks swamy swamydp wrote: > = > Hi John > = > Sorry for getting back late. = > = > I have been debugging further using the UART to send output directly to > serial post. Now I see that just after entering start_kernel, a ITLB miss > exception occurs and linux hangs at that point. = > = > Looks like the kernel is probably not running at all yet, may stuck in > early initialization. > = >>> Yes > = > 1. Has the kernel ever ran on this board or is this development to get > it running? > = >>> No. This is a new board and I am trying to build a simple EDK system >>> with only > PPC, UART, PIC as the devices. > = > 2. Not sure on the tools you are using to build it. You mention the > EDK, but you must not be using it's compiler as it's not configured in > the EDK to build Linux. = > = >>> EDK 9.2 version, XMD for debug. Kernel 2.6 version is built in linux >>> machine and zImage.elf is downloaded > to the board. > = > Thanks for the UART suggestion, works well. Any suggestions as to what > might be wrong in start_kernel function ? I will continue debugging > meanwhile. > = > Thanks > swamy > = > = > = > = -- = View this message in context: http://www.nabble.com/linux-2.6-hangs-at-__delay-function-on-Viretx-4-bo ard-tp17222725p17482754.html Sent from the linuxppc-embedded mailing list archive at Nabble.com. _______________________________________________ Linuxppc-embedded mailing list Linuxppc-embedded@ozlabs.org https://ozlabs.org/mailman/listinfo/linuxppc-embedded This email and any attachments are intended for the sole use of the named r= ecipient(s) and contain(s) confidential information that may be proprietary= , privileged or copyrighted under applicable law. If you are not the intend= ed recipient, do not read, copy, or forward this email message or any attac= hments. Delete this email message and any attachments immediately. ^ permalink raw reply [flat|nested] 14+ messages in thread
* RE: linux 2.6 hangs at __delay function on Viretx 4 board 2008-05-28 14:07 ` John Linn @ 2008-06-04 3:00 ` swamydp 2008-06-04 8:55 ` Peter Korsgaard 0 siblings, 1 reply; 14+ messages in thread From: swamydp @ 2008-06-04 3:00 UTC (permalink / raw) To: linuxppc-embedded Hi John I am using UARTLITE as serial console. I do not have license for UART 16550. I have enabled the drivers for uartlite in menuconfig while configuring the kernel. I have tested all combinations for the kernel command line - tty0, ttyUL0, ttyl0, ttyS0 but could not get uartlite to output kernel printk messages. Since I am using uartlite , the following settings are turned off in menuconfig CONFIG_SERIAL_8250=n CONFIG_SERIAL_8250_CONSOLE=n I have seen many posts claim that uartlite seems to work with ttyUL0 setting in the kernel command line but I am having trouble with that. Thanks swamy Hi Swamy, Sorry for the long delay. Sounds like the console is not setup correctly. I notice in your command line it appears that you have 2 console statements. I have not tested this ever and I would change it to only have the console=ttyS0,9600. I have seen other mailings, no Xilinx specific, related to this causing problems. This console setup assumes you're using the Xilinx 16550 UART. It could be an issue with the xparameters*.h file with the address of the UART. Have you compared your arch/ppc/platforms/4xx/xparameters/xparameters*.h file, whichever one it's setup to use, to the ones that we provided in the Git tree? I'm assuming you have the kernel configured correctly to use the UART16550 driver and the console is turned on, both are needed. The 16550 is 8250 compatible (mostly) and works with it's driver from Linux. CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y Thanks, John -- View this message in context: http://www.nabble.com/linux-2.6-hangs-at-__delay-function-on-Viretx-4-board-tp17222725p17638198.html Sent from the linuxppc-embedded mailing list archive at Nabble.com. ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: linux 2.6 hangs at __delay function on Viretx 4 board 2008-06-04 3:00 ` swamydp @ 2008-06-04 8:55 ` Peter Korsgaard 2008-06-04 21:22 ` John Linn 0 siblings, 1 reply; 14+ messages in thread From: Peter Korsgaard @ 2008-06-04 8:55 UTC (permalink / raw) To: swamydp; +Cc: linuxppc-embedded >>>>> "swamydp" == swamydp <swamydp@gmail.com> writes: swamydp> Hi John swamydp> I am using UARTLITE as serial console. I do not have license swamydp> for UART 16550. I have enabled the drivers for uartlite in swamydp> menuconfig while configuring the kernel. I have tested all swamydp> combinations for the kernel command line - tty0, ttyUL0, swamydp> ttyl0, ttyS0 but could not get uartlite to output kernel swamydp> printk messages. Correct syntax is console=ttyUL0 swamydp> Since I am using uartlite , the following settings are swamydp> turned off in menuconfig swamydp> CONFIG_SERIAL_8250=n swamydp> CONFIG_SERIAL_8250_CONSOLE=n Do you have console on uartlite (CONFIG_SERIAL_UARTLITE_CONSOLE) enabled? -- Bye, Peter Korsgaard ^ permalink raw reply [flat|nested] 14+ messages in thread
* RE: linux 2.6 hangs at __delay function on Viretx 4 board 2008-06-04 8:55 ` Peter Korsgaard @ 2008-06-04 21:22 ` John Linn 2008-06-04 21:31 ` Peter Korsgaard 2008-06-04 21:44 ` Howard, Marc 0 siblings, 2 replies; 14+ messages in thread From: John Linn @ 2008-06-04 21:22 UTC (permalink / raw) To: Peter Korsgaard, swamydp; +Cc: linuxppc-embedded Hi Peter, Yes you need to enable UARTLITE as the console in the kernel configuration. You have the command line syntax, ttyUL0, correct. They have now changed the UART 16550 to be a free core in the EDK, not sure which version of the EDK that happened. Thanks, John -----Original Message----- From: linuxppc-embedded-bounces+john.linn=3Dxilinx.com@ozlabs.org [mailto:linuxppc-embedded-bounces+john.linn=3Dxilinx.com@ozlabs.org] On Behalf Of Peter Korsgaard Sent: Wednesday, June 04, 2008 2:56 AM To: swamydp Cc: linuxppc-embedded@ozlabs.org Subject: Re: linux 2.6 hangs at __delay function on Viretx 4 board >>>>> "swamydp" =3D=3D swamydp <swamydp@gmail.com> writes: swamydp> Hi John swamydp> I am using UARTLITE as serial console. I do not have license swamydp> for UART 16550. I have enabled the drivers for uartlite in swamydp> menuconfig while configuring the kernel. I have tested all swamydp> combinations for the kernel command line - tty0, ttyUL0, swamydp> ttyl0, ttyS0 but could not get uartlite to output kernel swamydp> printk messages. Correct syntax is console=3DttyUL0 swamydp> Since I am using uartlite , the following settings are swamydp> turned off in menuconfig swamydp> CONFIG_SERIAL_8250=3Dn swamydp> CONFIG_SERIAL_8250_CONSOLE=3Dn Do you have console on uartlite (CONFIG_SERIAL_UARTLITE_CONSOLE) enabled? -- = Bye, Peter Korsgaard _______________________________________________ Linuxppc-embedded mailing list Linuxppc-embedded@ozlabs.org https://ozlabs.org/mailman/listinfo/linuxppc-embedded This email and any attachments are intended for the sole use of the named r= ecipient(s) and contain(s) confidential information that may be proprietary= , privileged or copyrighted under applicable law. If you are not the intend= ed recipient, do not read, copy, or forward this email message or any attac= hments. Delete this email message and any attachments immediately. ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: linux 2.6 hangs at __delay function on Viretx 4 board 2008-06-04 21:22 ` John Linn @ 2008-06-04 21:31 ` Peter Korsgaard 2008-06-04 21:44 ` Howard, Marc 1 sibling, 0 replies; 14+ messages in thread From: Peter Korsgaard @ 2008-06-04 21:31 UTC (permalink / raw) To: John Linn; +Cc: swamydp, linuxppc-embedded >>>>> "John" == John Linn <John.Linn@xilinx.com> writes: John> Hi Peter, John> Yes you need to enable UARTLITE as the console in the kernel John> configuration. Yeah, I know - I wrote the driver after all ;) John> You have the command line syntax, ttyUL0, correct. John> They have now changed the UART 16550 to be a free core in the EDK, not John> sure which version of the EDK that happened. Ok. -- Bye, Peter Korsgaard ^ permalink raw reply [flat|nested] 14+ messages in thread
* RE: linux 2.6 hangs at __delay function on Viretx 4 board 2008-06-04 21:22 ` John Linn 2008-06-04 21:31 ` Peter Korsgaard @ 2008-06-04 21:44 ` Howard, Marc 2008-06-04 23:18 ` Stephen Neuendorffer 1 sibling, 1 reply; 14+ messages in thread From: Howard, Marc @ 2008-06-04 21:44 UTC (permalink / raw) To: John Linn, Peter Korsgaard, swamydp; +Cc: linuxppc-embedded Every year at the Embedded Systems Conference I would complain to the Xilinix folks about the 16550 not being free. This year I complained & they told me that even though it is listed as a purchased core when you go to "buy" it you get it for free. This was just prior to the 10.x release. Marc W Howard=20 > -----Original Message----- > From:=20 > linuxppc-embedded-bounces+marc.howard=3Dkla-tencor.com@ozlabs.or g [mailto:linuxppc-embedded-bounces+marc.howard=3Dkla-> tencor.com@ozlabs.org] On Behalf Of John Linn > Sent: Wednesday, June 04, 2008 2:23 PM > To: Peter Korsgaard; swamydp > Cc: linuxppc-embedded@ozlabs.org > Subject: RE: linux 2.6 hangs at __delay function on Viretx 4 board >=20 > Hi Peter, >=20 > Yes you need to enable UARTLITE as the console in the kernel > configuration. >=20 > You have the command line syntax, ttyUL0, correct. >=20 > They have now changed the UART 16550 to be a free core in the EDK, not > sure which version of the EDK that happened. >=20 > Thanks, > John >=20 > -----Original Message----- > From: linuxppc-embedded-bounces+john.linn=3Dxilinx.com@ozlabs.org > [mailto:linuxppc-embedded-bounces+john.linn=3Dxilinx.com@ozlabs.org] = On > Behalf Of Peter Korsgaard > Sent: Wednesday, June 04, 2008 2:56 AM > To: swamydp > Cc: linuxppc-embedded@ozlabs.org > Subject: Re: linux 2.6 hangs at __delay function on Viretx 4 board >=20 > >>>>> "swamydp" =3D=3D swamydp <swamydp@gmail.com> writes: >=20 > swamydp> Hi John >=20 > swamydp> I am using UARTLITE as serial console. I do not have license > swamydp> for UART 16550. I have enabled the drivers for uartlite in > swamydp> menuconfig while configuring the kernel. I have tested all > swamydp> combinations for the kernel command line - tty0, ttyUL0, > swamydp> ttyl0, ttyS0 but could not get uartlite to output kernel > swamydp> printk messages. >=20 > Correct syntax is console=3DttyUL0 >=20 > swamydp> Since I am using uartlite , the following settings are > swamydp> turned off in menuconfig >=20 > swamydp> CONFIG_SERIAL_8250=3Dn > swamydp> CONFIG_SERIAL_8250_CONSOLE=3Dn >=20 > Do you have console on uartlite (CONFIG_SERIAL_UARTLITE_CONSOLE) > enabled? >=20 > --=20 > Bye, Peter Korsgaard > _______________________________________________ > Linuxppc-embedded mailing list > Linuxppc-embedded@ozlabs.org > https://ozlabs.org/mailman/listinfo/linuxppc-embedded >=20 >=20 > This email and any attachments are intended for the sole use=20 > of the named recipient(s) and contain(s) confidential=20 > information that may be proprietary, privileged or=20 > copyrighted under applicable law. If you are not the intended=20 > recipient, do not read, copy, or forward this email message=20 > or any attachments. Delete this email message and any=20 > attachments immediately. >=20 >=20 > _______________________________________________ > Linuxppc-embedded mailing list > Linuxppc-embedded@ozlabs.org > https://ozlabs.org/mailman/listinfo/linuxppc-embedded >=20 ^ permalink raw reply [flat|nested] 14+ messages in thread
* RE: linux 2.6 hangs at __delay function on Viretx 4 board 2008-06-04 21:44 ` Howard, Marc @ 2008-06-04 23:18 ` Stephen Neuendorffer 0 siblings, 0 replies; 14+ messages in thread From: Stephen Neuendorffer @ 2008-06-04 23:18 UTC (permalink / raw) To: Howard, Marc, John Linn, Peter Korsgaard, swamydp; +Cc: linuxppc-embedded In 10.1, it is actually free... > -----Original Message----- > From: linuxppc-embedded-bounces+stephen=3Dneuendorffer.name@ozlabs.org [mailto:linuxppc-embedded- > bounces+stephen=3Dneuendorffer.name@ozlabs.org] On Behalf Of Howard, Marc > Sent: Wednesday, June 04, 2008 2:45 PM > To: John Linn; Peter Korsgaard; swamydp > Cc: linuxppc-embedded@ozlabs.org > Subject: RE: linux 2.6 hangs at __delay function on Viretx 4 board > = > Every year at the Embedded Systems Conference I would complain to the > Xilinix folks about the 16550 not being free. This year I complained & > they told me that even though it is listed as a purchased core when you > go to "buy" it you get it for free. This was just prior to the 10.x > release. > = > Marc W Howard > = > > -----Original Message----- > > From: > > linuxppc-embedded-bounces+marc.howard=3Dkla-tencor.com@ozlabs.or > g [mailto:linuxppc-embedded-bounces+marc.howard=3Dkla-> > tencor.com@ozlabs.org] On Behalf Of John Linn > > Sent: Wednesday, June 04, 2008 2:23 PM > > To: Peter Korsgaard; swamydp > > Cc: linuxppc-embedded@ozlabs.org > > Subject: RE: linux 2.6 hangs at __delay function on Viretx 4 board > > > > Hi Peter, > > > > Yes you need to enable UARTLITE as the console in the kernel > > configuration. > > > > You have the command line syntax, ttyUL0, correct. > > > > They have now changed the UART 16550 to be a free core in the EDK, not > > sure which version of the EDK that happened. > > > > Thanks, > > John > > > > -----Original Message----- > > From: linuxppc-embedded-bounces+john.linn=3Dxilinx.com@ozlabs.org > > [mailto:linuxppc-embedded-bounces+john.linn=3Dxilinx.com@ozlabs.org] On > > Behalf Of Peter Korsgaard > > Sent: Wednesday, June 04, 2008 2:56 AM > > To: swamydp > > Cc: linuxppc-embedded@ozlabs.org > > Subject: Re: linux 2.6 hangs at __delay function on Viretx 4 board > > > > >>>>> "swamydp" =3D=3D swamydp <swamydp@gmail.com> writes: > > > > swamydp> Hi John > > > > swamydp> I am using UARTLITE as serial console. I do not have license > > swamydp> for UART 16550. I have enabled the drivers for uartlite in > > swamydp> menuconfig while configuring the kernel. I have tested all > > swamydp> combinations for the kernel command line - tty0, ttyUL0, > > swamydp> ttyl0, ttyS0 but could not get uartlite to output kernel > > swamydp> printk messages. > > > > Correct syntax is console=3DttyUL0 > > > > swamydp> Since I am using uartlite , the following settings are > > swamydp> turned off in menuconfig > > > > swamydp> CONFIG_SERIAL_8250=3Dn > > swamydp> CONFIG_SERIAL_8250_CONSOLE=3Dn > > > > Do you have console on uartlite (CONFIG_SERIAL_UARTLITE_CONSOLE) > > enabled? > > > > -- > > Bye, Peter Korsgaard > > _______________________________________________ > > Linuxppc-embedded mailing list > > Linuxppc-embedded@ozlabs.org > > https://ozlabs.org/mailman/listinfo/linuxppc-embedded > > > > > > This email and any attachments are intended for the sole use > > of the named recipient(s) and contain(s) confidential > > information that may be proprietary, privileged or > > copyrighted under applicable law. If you are not the intended > > recipient, do not read, copy, or forward this email message > > or any attachments. Delete this email message and any > > attachments immediately. > > > > > > _______________________________________________ > > Linuxppc-embedded mailing list > > Linuxppc-embedded@ozlabs.org > > https://ozlabs.org/mailman/listinfo/linuxppc-embedded > > > _______________________________________________ > Linuxppc-embedded mailing list > Linuxppc-embedded@ozlabs.org > https://ozlabs.org/mailman/listinfo/linuxppc-embedded This email and any attachments are intended for the sole use of the named r= ecipient(s) and contain(s) confidential information that may be proprietary= , privileged or copyrighted under applicable law. If you are not the intend= ed recipient, do not read, copy, or forward this email message or any attac= hments. Delete this email message and any attachments immediately. ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: linux 2.6 hangs at __delay function on Viretx 4 board 2008-05-14 3:29 linux 2.6 hangs at __delay function on Viretx 4 board swamydp 2008-05-14 15:01 ` John Linn @ 2008-06-19 16:33 ` swamydp 1 sibling, 0 replies; 14+ messages in thread From: swamydp @ 2008-06-19 16:33 UTC (permalink / raw) To: linuxppc-embedded Hello Sorry for the late reply. I was busy with another project. I finally got linux 2.6 to boot on HITECH board. Thanks to John Linn for all the pointers to debug the code. I also got the UARTLITE as console working. I had to disable several macros in virtex_devices.c to make the kernel boot. Now I am working on using UART16550 as console which is free at Xilinx after registration. Thanks to Marc and Stephen for the info. --swamy swamydp wrote: > > > I am trying to boot linux 2.6 on HITECH virtex 4(fx60) board. Linux hangs > at address 0xc00045ec which is in the __udelay function. I am using EDK > 9.2i and gcc version 4.0.2 for compiling the kernel. The following is the > boot message from the bootloader. > > loaded at: 00400000 0054E19C > board data at: 0054C120 0054C19C > relocated to: 00404064 004040E0 > zimage at: 00404E55 0054B5B4 > avail ram: 0054F000 02000000 > > Linux/PPC load: console=ttyS0,9600 console=tty0 root=/dev/sda2 > Uncompressing Linux...done. > Now booting the kernel > > Any help is greatly appreciated. I have run out of ideas to fix this. > > Thanks > swamy > > -- View this message in context: http://www.nabble.com/linux-2.6-hangs-at-__delay-function-on-Viretx-4-board-tp17222725p18012972.html Sent from the linuxppc-embedded mailing list archive at Nabble.com. ^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2008-06-19 16:33 UTC | newest] Thread overview: 14+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2008-05-14 3:29 linux 2.6 hangs at __delay function on Viretx 4 board swamydp 2008-05-14 15:01 ` John Linn 2008-05-16 14:56 ` swamydp 2008-05-16 16:28 ` John Linn 2008-05-25 5:35 ` swamydp 2008-05-27 4:11 ` swamydp 2008-05-28 14:07 ` John Linn 2008-06-04 3:00 ` swamydp 2008-06-04 8:55 ` Peter Korsgaard 2008-06-04 21:22 ` John Linn 2008-06-04 21:31 ` Peter Korsgaard 2008-06-04 21:44 ` Howard, Marc 2008-06-04 23:18 ` Stephen Neuendorffer 2008-06-19 16:33 ` swamydp
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).