[PATCH 0/4] Fix RTC for MPC8572DS and support RTC on MPC8610HPCD

[PATCH 0/4] Fix RTC for MPC8572DS and support RTC on MPC8610HPCD

[Anton Vorontsov]

Hello Kumar,

The previous series scattered a bit, so I gathered it again.

I've found MPC8572DS board to test RTC quirk changes that I've made
for MPC8610HPCD, and it appears that without the change RTC does not
work on MPC8572DS, too.

So, the first patch actually fixes it for MPC8572DS, and also makes
RTC work on MPC8610HPCD. I still can't test the patch on MPC8641HPCD
and MPC8544DS (no boards handy), but I don't believe that the change
could break these boards.

I also dropped MACH_PCI_FIXUP_*() approach, and did just machine_is()s
inside the fixups. I think this looks better... as far as possible for
the board specific fixups. :-)

-- 
Anton Vorontsov
email: cbouatmailru@gmail.com
irc://irc.freenode.net/bd2

[PATCH 1/4] powerpc: fsl_uli1575: fix RTC quirk to work on MPC8572DS and MPC8610HPCD

[Anton Vorontsov]

This patch fixes RTC on MPC8572DS boards: dummy read helps only when
reading at the end of the bridge's memory (i.e. outside of behind the
bridge devices' assigned regions).

With this change the quirk also makes RTC work on MPC8610HPCD, so it's
unlikely that this will break MPC8641HPCN or MPC8544DS boards.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
 arch/powerpc/platforms/fsl_uli1575.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/arch/powerpc/platforms/fsl_uli1575.c b/arch/powerpc/platforms/fsl_uli1575.c
index afc9141..756561c 100644
--- a/arch/powerpc/platforms/fsl_uli1575.c
+++ b/arch/powerpc/platforms/fsl_uli1575.c
@@ -221,7 +221,7 @@ static void __devinit quirk_final_uli5249(struct pci_dev *dev)
 	for (i = 0; i < PCI_BUS_NUM_RESOURCES; i++) {
 		if ((bus->resource[i]) &&
 			(bus->resource[i]->flags & IORESOURCE_MEM)) {
-			dummy = ioremap(bus->resource[i]->start, 0x4);
+			dummy = ioremap(bus->resource[i]->end - 3, 0x4);
 			if (dummy) {
 				in_8(dummy);
 				iounmap(dummy);
-- 
1.5.5.4

Re: [PATCH 1/4] powerpc: fsl_uli1575: fix RTC quirk to work on MPC8572DS and MPC8610HPCD

[Kumar Gala]

On Jun 11, 2008, at 6:04 PM, Anton Vorontsov wrote:

> This patch fixes RTC on MPC8572DS boards: dummy read helps only when
> reading at the end of the bridge's memory (i.e. outside of behind the
> bridge devices' assigned regions).
>
> With this change the quirk also makes RTC work on MPC8610HPCD, so it's
> unlikely that this will break MPC8641HPCN or MPC8544DS boards.
>
> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
> ---
> arch/powerpc/platforms/fsl_uli1575.c |    2 +-
> 1 files changed, 1 insertions(+), 1 deletions(-)

applied.

- k

[PATCH 2/4] powerpc/85xx/86xx: some refactoring for fsl_uli1575 code

[Anton Vorontsov]

- Get rid of uses_fsl_uli_m1575, it does not scale for all cases.
  Instead, let's explicitly use machine_is() for each fixup.
- Factor out MPC8610HPCD quirks to fsl_uli1575, and protect them with
  machine_is(). One step closer to multiplatform kernels.
- Actually use fsl_uli1575 on MPC8610HPCD, so RTC quirk will be applied.
- RTC quirk applies to all boards though, so no machine_is() checks.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
 arch/powerpc/platforms/85xx/mpc85xx_ds.c   |    2 -
 arch/powerpc/platforms/86xx/Kconfig        |    1 +
 arch/powerpc/platforms/86xx/mpc8610_hpcd.c |   87 ---------------------
 arch/powerpc/platforms/86xx/mpc86xx_hpcn.c |    2 -
 arch/powerpc/platforms/fsl_uli1575.c       |  115 ++++++++++++++++++++++++++--
 5 files changed, 108 insertions(+), 99 deletions(-)

diff --git a/arch/powerpc/platforms/85xx/mpc85xx_ds.c b/arch/powerpc/platforms/85xx/mpc85xx_ds.c
index b010dc9..f21e7a6 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_ds.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_ds.c
@@ -115,7 +115,6 @@ void __init mpc85xx_ds_pic_init(void)
 
 #ifdef CONFIG_PCI
 static int primary_phb_addr;
-extern int uses_fsl_uli_m1575;
 extern int uli_exclude_device(struct pci_controller *hose,
 				u_char bus, u_char devfn);
 
@@ -161,7 +160,6 @@ static void __init mpc85xx_ds_setup_arch(void)
 		}
 	}
 
-	uses_fsl_uli_m1575 = 1;
 	ppc_md.pci_exclude_device = mpc85xx_exclude_device;
 #endif
 
diff --git a/arch/powerpc/platforms/86xx/Kconfig b/arch/powerpc/platforms/86xx/Kconfig
index 053f49a..39c02af 100644
--- a/arch/powerpc/platforms/86xx/Kconfig
+++ b/arch/powerpc/platforms/86xx/Kconfig
@@ -21,6 +21,7 @@ config SBC8641D
 config MPC8610_HPCD
 	bool "Freescale MPC8610 HPCD"
 	select DEFAULT_UIMAGE
+	select FSL_ULI1575
 	help
 	  This option enables support for the MPC8610 HPCD board.
 
diff --git a/arch/powerpc/platforms/86xx/mpc8610_hpcd.c b/arch/powerpc/platforms/86xx/mpc8610_hpcd.c
index eb16208..539a6ad 100644
--- a/arch/powerpc/platforms/86xx/mpc8610_hpcd.c
+++ b/arch/powerpc/platforms/86xx/mpc8610_hpcd.c
@@ -78,93 +78,6 @@ static void __init mpc86xx_hpcd_init_irq(void)
 	mpic_init(mpic1);
 }
 
-#ifdef CONFIG_PCI
-static void __devinit quirk_uli1575(struct pci_dev *dev)
-{
-	u32 temp32;
-
-	/* Disable INTx */
-	pci_read_config_dword(dev, 0x48, &temp32);
-	pci_write_config_dword(dev, 0x48, (temp32 | 1<<26));
-
-	/* Enable sideband interrupt */
-	pci_read_config_dword(dev, 0x90, &temp32);
-	pci_write_config_dword(dev, 0x90, (temp32 | 1<<22));
-}
-
-static void __devinit quirk_uli5288(struct pci_dev *dev)
-{
-	unsigned char c;
-	unsigned short temp;
-
-	/* Interrupt Disable, Needed when SATA disabled */
-	pci_read_config_word(dev, PCI_COMMAND, &temp);
-	temp |= 1<<10;
-	pci_write_config_word(dev, PCI_COMMAND, temp);
-
-	pci_read_config_byte(dev, 0x83, &c);
-	c |= 0x80;
-	pci_write_config_byte(dev, 0x83, c);
-
-	pci_write_config_byte(dev, PCI_CLASS_PROG, 0x01);
-	pci_write_config_byte(dev, PCI_CLASS_DEVICE, 0x06);
-
-	pci_read_config_byte(dev, 0x83, &c);
-	c &= 0x7f;
-	pci_write_config_byte(dev, 0x83, c);
-}
-
-/*
- * Since 8259PIC was disabled on the board, the IDE device can not
- * use the legacy IRQ, we need to let the IDE device work under
- * native mode and use the interrupt line like other PCI devices.
- * IRQ14 is a sideband interrupt from IDE device to CPU and we use this
- * as the interrupt for IDE device.
- */
-static void __devinit quirk_uli5229(struct pci_dev *dev)
-{
-	unsigned char c;
-
-	pci_read_config_byte(dev, 0x4b, &c);
-	c |= 0x10;
-	pci_write_config_byte(dev, 0x4b, c);
-}
-
-/*
- * SATA interrupt pin bug fix
- * There's a chip bug for 5288, The interrupt pin should be 2,
- * not the read only value 1, So it use INTB#, not INTA# which
- * actually used by the IDE device 5229.
- * As of this bug, during the PCI initialization, 5288 read the
- * irq of IDE device from the device tree, this function fix this
- * bug by re-assigning a correct irq to 5288.
- *
- */
-static void __devinit final_uli5288(struct pci_dev *dev)
-{
-	struct pci_controller *hose = pci_bus_to_host(dev->bus);
-	struct device_node *hosenode = hose ? hose->dn : NULL;
-	struct of_irq oirq;
-	int virq, pin = 2;
-	u32 laddr[3];
-
-	if (!hosenode)
-		return;
-
-	laddr[0] = (hose->first_busno << 16) | (PCI_DEVFN(31, 0) << 8);
-	laddr[1] = laddr[2] = 0;
-	of_irq_map_raw(hosenode, &pin, 1, laddr, &oirq);
-	virq = irq_create_of_mapping(oirq.controller, oirq.specifier,
-				     oirq.size);
-	dev->irq = virq;
-}
-
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x1575, quirk_uli1575);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5288, quirk_uli5288);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5229, quirk_uli5229);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, 0x5288, final_uli5288);
-#endif /* CONFIG_PCI */
-
 #if defined(CONFIG_FB_FSL_DIU) || defined(CONFIG_FB_FSL_DIU_MODULE)
 
 static u32 get_busfreq(void)
diff --git a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
index f13704a..22ce0f3 100644
--- a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
+++ b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
@@ -107,7 +107,6 @@ mpc86xx_hpcn_init_irq(void)
 }
 
 #ifdef CONFIG_PCI
-extern int uses_fsl_uli_m1575;
 extern int uli_exclude_device(struct pci_controller *hose,
 				u_char bus, u_char devfn);
 
@@ -149,7 +148,6 @@ mpc86xx_hpcn_setup_arch(void)
 			fsl_add_bridge(np, 0);
 	}
 
-	uses_fsl_uli_m1575 = 1;
 	ppc_md.pci_exclude_device = mpc86xx_exclude_device;
 
 #endif
diff --git a/arch/powerpc/platforms/fsl_uli1575.c b/arch/powerpc/platforms/fsl_uli1575.c
index 756561c..ef74a07 100644
--- a/arch/powerpc/platforms/fsl_uli1575.c
+++ b/arch/powerpc/platforms/fsl_uli1575.c
@@ -51,15 +51,13 @@ u8 uli_pirq_to_irq[8] = {
 	ULI_8259_NONE,		/* PIRQH */
 };
 
-/* set in board code if you want this quirks to do something */
-int uses_fsl_uli_m1575;
-
 /* Bridge */
 static void __devinit early_uli5249(struct pci_dev *dev)
 {
 	unsigned char temp;
 
-	if (!uses_fsl_uli_m1575)
+	if (!machine_is(mpc86xx_hpcn) && !machine_is(mpc8544_ds) &&
+			!machine_is(mpc8572_ds))
 		return;
 
 	pci_write_config_word(dev, PCI_COMMAND, PCI_COMMAND_IO |
@@ -82,7 +80,8 @@ static void __devinit quirk_uli1575(struct pci_dev *dev)
 {
 	int i;
 
-	if (!uses_fsl_uli_m1575)
+	if (!machine_is(mpc86xx_hpcn) && !machine_is(mpc8544_ds) &&
+			!machine_is(mpc8572_ds))
 		return;
 
 	/*
@@ -150,7 +149,8 @@ static void __devinit quirk_final_uli1575(struct pci_dev *dev)
 	 * IRQ 14: Edge
 	 * IRQ 15: Edge
 	 */
-	if (!uses_fsl_uli_m1575)
+	if (!machine_is(mpc86xx_hpcn) && !machine_is(mpc8544_ds) &&
+			!machine_is(mpc8572_ds))
 		return;
 
 	outb(0xfa, 0x4d0);
@@ -176,7 +176,8 @@ static void __devinit quirk_uli5288(struct pci_dev *dev)
 	unsigned char c;
 	unsigned int d;
 
-	if (!uses_fsl_uli_m1575)
+	if (!machine_is(mpc86xx_hpcn) && !machine_is(mpc8544_ds) &&
+			!machine_is(mpc8572_ds))
 		return;
 
 	/* read/write lock */
@@ -200,7 +201,8 @@ static void __devinit quirk_uli5229(struct pci_dev *dev)
 {
 	unsigned short temp;
 
-	if (!uses_fsl_uli_m1575)
+	if (!machine_is(mpc86xx_hpcn) && !machine_is(mpc8544_ds) &&
+			!machine_is(mpc8572_ds))
 		return;
 
 	pci_write_config_word(dev, PCI_COMMAND, PCI_COMMAND_INTX_DISABLE |
@@ -238,6 +240,103 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5229, quirk_uli5229);
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, 0x5249, quirk_final_uli5249);
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, 0x1575, quirk_final_uli1575);
 
+static void __devinit hpcd_quirk_uli1575(struct pci_dev *dev)
+{
+	u32 temp32;
+
+	if (!machine_is(mpc86xx_hpcd))
+		return;
+
+	/* Disable INTx */
+	pci_read_config_dword(dev, 0x48, &temp32);
+	pci_write_config_dword(dev, 0x48, (temp32 | 1<<26));
+
+	/* Enable sideband interrupt */
+	pci_read_config_dword(dev, 0x90, &temp32);
+	pci_write_config_dword(dev, 0x90, (temp32 | 1<<22));
+}
+
+static void __devinit hpcd_quirk_uli5288(struct pci_dev *dev)
+{
+	unsigned char c;
+	unsigned short temp;
+
+	if (!machine_is(mpc86xx_hpcd))
+		return;
+
+	/* Interrupt Disable, Needed when SATA disabled */
+	pci_read_config_word(dev, PCI_COMMAND, &temp);
+	temp |= 1<<10;
+	pci_write_config_word(dev, PCI_COMMAND, temp);
+
+	pci_read_config_byte(dev, 0x83, &c);
+	c |= 0x80;
+	pci_write_config_byte(dev, 0x83, c);
+
+	pci_write_config_byte(dev, PCI_CLASS_PROG, 0x01);
+	pci_write_config_byte(dev, PCI_CLASS_DEVICE, 0x06);
+
+	pci_read_config_byte(dev, 0x83, &c);
+	c &= 0x7f;
+	pci_write_config_byte(dev, 0x83, c);
+}
+
+/*
+ * Since 8259PIC was disabled on the board, the IDE device can not
+ * use the legacy IRQ, we need to let the IDE device work under
+ * native mode and use the interrupt line like other PCI devices.
+ * IRQ14 is a sideband interrupt from IDE device to CPU and we use this
+ * as the interrupt for IDE device.
+ */
+static void __devinit hpcd_quirk_uli5229(struct pci_dev *dev)
+{
+	unsigned char c;
+
+	if (!machine_is(mpc86xx_hpcd))
+		return;
+
+	pci_read_config_byte(dev, 0x4b, &c);
+	c |= 0x10;
+	pci_write_config_byte(dev, 0x4b, c);
+}
+
+/*
+ * SATA interrupt pin bug fix
+ * There's a chip bug for 5288, The interrupt pin should be 2,
+ * not the read only value 1, So it use INTB#, not INTA# which
+ * actually used by the IDE device 5229.
+ * As of this bug, during the PCI initialization, 5288 read the
+ * irq of IDE device from the device tree, this function fix this
+ * bug by re-assigning a correct irq to 5288.
+ *
+ */
+static void __devinit hpcd_final_uli5288(struct pci_dev *dev)
+{
+	struct pci_controller *hose = pci_bus_to_host(dev->bus);
+	struct device_node *hosenode = hose ? hose->dn : NULL;
+	struct of_irq oirq;
+	int virq, pin = 2;
+	u32 laddr[3];
+
+	if (!machine_is(mpc86xx_hpcd))
+		return;
+
+	if (!hosenode)
+		return;
+
+	laddr[0] = (hose->first_busno << 16) | (PCI_DEVFN(31, 0) << 8);
+	laddr[1] = laddr[2] = 0;
+	of_irq_map_raw(hosenode, &pin, 1, laddr, &oirq);
+	virq = irq_create_of_mapping(oirq.controller, oirq.specifier,
+				     oirq.size);
+	dev->irq = virq;
+}
+
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x1575, hpcd_quirk_uli1575);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5288, hpcd_quirk_uli5288);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5229, hpcd_quirk_uli5229);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, 0x5288, hpcd_final_uli5288);
+
 int uli_exclude_device(struct pci_controller *hose,
 			u_char bus, u_char devfn)
 {
-- 
1.5.5.4

[PATCH 3/4] powerpc: rtc_cmos_setup: assign interrupts only if there is i8259 PIC

[Anton Vorontsov]

i8259 PIC is disabled on MPC8610HPCD boards, thus currently rtc-cmos
driver fails to probe.

To fix the issue, we lookup the device tree for "chrp,iic" and
"pnpPNP,000" compatible devices, and if not found we do not assign RTC
IRQ and assuming that i8259 was disabled.

Though this patch fixes RTC on some boards (and surely should not break
any other), the whole approach is still broken. We can't easily fix this
though, because old device trees do not specify i8259 interrupts for the
cmos rtc node.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
 arch/powerpc/sysdev/rtc_cmos_setup.c |   23 +++++++++++++++++------
 1 files changed, 17 insertions(+), 6 deletions(-)

diff --git a/arch/powerpc/sysdev/rtc_cmos_setup.c b/arch/powerpc/sysdev/rtc_cmos_setup.c
index c09ddc0..c1879eb 100644
--- a/arch/powerpc/sysdev/rtc_cmos_setup.c
+++ b/arch/powerpc/sysdev/rtc_cmos_setup.c
@@ -21,6 +21,7 @@ static int  __init add_rtc(void)
 	struct device_node *np;
 	struct platform_device *pd;
 	struct resource res[2];
+	unsigned int num_res = 1;
 	int ret;
 
 	memset(&res, 0, sizeof(res));
@@ -41,14 +42,24 @@ static int  __init add_rtc(void)
 	if (res[0].start != RTC_PORT(0))
 		return -EINVAL;
 
-	/* Use a fixed interrupt value of 8 since on PPC if we are using this
-	 * its off an i8259 which we ensure has interrupt numbers 0..15. */
-	res[1].start = 8;
-	res[1].end = 8;
-	res[1].flags = IORESOURCE_IRQ;
+	np = of_find_compatible_node(NULL, NULL, "chrp,iic");
+	if (!np)
+		np = of_find_compatible_node(NULL, NULL, "pnpPNP,000");
+	if (np) {
+		of_node_put(np);
+		/*
+		 * Use a fixed interrupt value of 8 since on PPC if we are
+		 * using this its off an i8259 which we ensure has interrupt
+		 * numbers 0..15.
+		 */
+		res[1].start = 8;
+		res[1].end = 8;
+		res[1].flags = IORESOURCE_IRQ;
+		num_res++;
+	}
 
 	pd = platform_device_register_simple("rtc_cmos", -1,
-					     &res[0], 2);
+					     &res[0], num_res);
 
 	if (IS_ERR(pd))
 		return PTR_ERR(pd);
-- 
1.5.5.4

Re: [PATCH 3/4] powerpc: rtc_cmos_setup: assign interrupts only if there is i8259 PIC

[Kumar Gala]

On Jun 11, 2008, at 6:04 PM, Anton Vorontsov wrote:

> i8259 PIC is disabled on MPC8610HPCD boards, thus currently rtc-cmos
> driver fails to probe.
>
> To fix the issue, we lookup the device tree for "chrp,iic" and
> "pnpPNP,000" compatible devices, and if not found we do not assign RTC
> IRQ and assuming that i8259 was disabled.
>
> Though this patch fixes RTC on some boards (and surely should not  
> break
> any other), the whole approach is still broken. We can't easily fix  
> this
> though, because old device trees do not specify i8259 interrupts for  
> the
> cmos rtc node.
>
> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
> ---
> arch/powerpc/sysdev/rtc_cmos_setup.c |   23 +++++++++++++++++------
> 1 files changed, 17 insertions(+), 6 deletions(-)

applied.

- k

[PATCH 4/4] powerpc/86xx: mpc8610_hpcd: add support for ULI RTC

[Anton Vorontsov]

The ULI "Super South Bridge" contains ISA bridge to the legacy
devices, such as Super IO mouse/keyboard/floppy disk controllers,
parallel port, i8259 interrupt controller and so on.

i8259 is disabled on the MPC8610HPCD, and other peripherals are not
traced out. So we use only RTC.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
 arch/powerpc/boot/dts/mpc8610_hpcd.dts      |   14 +++++++
 arch/powerpc/configs/mpc8610_hpcd_defconfig |   51 ++++++++++++++++++++++++--
 2 files changed, 61 insertions(+), 4 deletions(-)

diff --git a/arch/powerpc/boot/dts/mpc8610_hpcd.dts b/arch/powerpc/boot/dts/mpc8610_hpcd.dts
index 65a5f64..c4507cd 100644
--- a/arch/powerpc/boot/dts/mpc8610_hpcd.dts
+++ b/arch/powerpc/boot/dts/mpc8610_hpcd.dts
@@ -388,6 +388,20 @@
 					  0x01000000 0x0 0x00000000
 					  0x01000000 0x0 0x00000000
 					  0x0 0x00100000>;
+
+				isa@1e {
+					device_type = "isa";
+					#size-cells = <1>;
+					#address-cells = <2>;
+					reg = <0xf000 0 0 0 0>;
+					ranges = <1 0 0x01000000 0 0
+						  0x00001000>;
+
+					rtc@70 {
+						compatible = "pnpPNP,b00";
+						reg = <1 0x70 2>;
+					};
+				};
 			};
 		};
 	};
diff --git a/arch/powerpc/configs/mpc8610_hpcd_defconfig b/arch/powerpc/configs/mpc8610_hpcd_defconfig
index 7e5b9ce..5885597 100644
--- a/arch/powerpc/configs/mpc8610_hpcd_defconfig
+++ b/arch/powerpc/configs/mpc8610_hpcd_defconfig
@@ -813,7 +813,6 @@ CONFIG_UNIX98_PTYS=y
 # CONFIG_IPMI_HANDLER is not set
 # CONFIG_HW_RANDOM is not set
 # CONFIG_NVRAM is not set
-# CONFIG_GEN_RTC is not set
 # CONFIG_R3964 is not set
 # CONFIG_APPLICOM is not set
 # CONFIG_RAW_DRIVER is not set
@@ -1065,12 +1064,56 @@ CONFIG_USB_ARCH_HAS_EHCI=y
 # CONFIG_NEW_LEDS is not set
 # CONFIG_INFINIBAND is not set
 # CONFIG_EDAC is not set
-# CONFIG_RTC_CLASS is not set
-# CONFIG_DMADEVICES is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_S35390A is not set
 
 #
-# Userspace I/O
+# SPI RTC drivers
 #
+
+#
+# Platform RTC drivers
+#
+CONFIG_RTC_DRV_CMOS=y
+# CONFIG_RTC_DRV_DS1511 is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
+# CONFIG_DMADEVICES is not set
 # CONFIG_UIO is not set
 
 #
-- 
1.5.5.4

Re: [PATCH 4/4] powerpc/86xx: mpc8610_hpcd: add support for ULI RTC

[Kumar Gala]

On Jun 11, 2008, at 6:04 PM, Anton Vorontsov wrote:

> The ULI "Super South Bridge" contains ISA bridge to the legacy
> devices, such as Super IO mouse/keyboard/floppy disk controllers,
> parallel port, i8259 interrupt controller and so on.
>
> i8259 is disabled on the MPC8610HPCD, and other peripherals are not
> traced out. So we use only RTC.
>
> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
> ---
> arch/powerpc/boot/dts/mpc8610_hpcd.dts      |   14 +++++++
> arch/powerpc/configs/mpc8610_hpcd_defconfig |   51 ++++++++++++++++++ 
> ++++++--
> 2 files changed, 61 insertions(+), 4 deletions(-)

applied.

- k