[PATCH] powerpc: add FHCI USB, FSL MCU, FSL UPM and GPIO LEDs bindings

[PATCH] powerpc: add FHCI USB, FSL MCU, FSL UPM and GPIO LEDs bindings

[Anton Vorontsov]

This patch adds few bindings for the new drivers to be submitted through
the appropriate maintainers.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---

Segher, thanks for the comments on the previous version. Do you see any
issues with this one or anything I could improve further?

And if there are no issues... Kumar, could you apply this for powerpc-next?

Thanks.

 Documentation/powerpc/booting-without-of.txt |  111 ++++++++++++++++++++++++++
 1 files changed, 111 insertions(+), 0 deletions(-)

diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index b68684d..a7ea549 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -62,6 +62,10 @@ Table of Contents
       s) Freescale on board FPGA
       t) Freescael MSI interrupt controller
       u) Freescale General-purpose Timers Module
+      v) Freescale QUICC Engine USB Controller
+      w) Freescale MCU with MPC8349E-mITX compatible firmware
+      x) Freescale Localbus UPM programmed to work with NAND flash
+      y) LEDs on GPIOs
 
   VII - Marvell Discovery mv64[345]6x System Controller chips
     1) The /system-controller node
@@ -2967,6 +2971,113 @@ platforms are moved over to use the flattened-device-tree model.
 	clock-frequency = <0>;
     };
 
+    v) Freescale QUICC Engine USB Controller
+
+    Required properties:
+      - compatible : should be "fsl,<chip>-qe-usb", "fsl,mpc8323-qe-usb";
+      - reg : the first two cells should contain usb registers location and
+        length, the next two two cells should contain PRAM location and
+        length.
+      - interrupts : should contain USB interrupt.
+      - interrupt-parent : interrupt source phandle.
+      - fsl,fullspeed-clock : specifies the full speed USB clock source:
+        "none": clock source is disabled
+        "brg1" through "brg16": clock source is BRG1-BRG16, respectively
+        "clk1" through "clk24": clock source is CLK1-CLK24, respectively
+      - fsl,lowspeed-clock : specifies the low speed USB clock source:
+        "none": clock source is disabled
+        "brg1" through "brg16": clock source is BRG1-BRG16, respectively
+        "clk1" through "clk24": clock source is CLK1-CLK24, respectively
+      - hub-power-budget : optional, USB power budget for the root hub, in mA.
+      - gpios : should specify GPIOs in this order: USBOE, USBTP, USBTN, USBRP,
+        USBRN, SPEED (optional), and POWER (optional).
+
+    Example:
+
+	usb@6c0 {
+		compatible = "fsl,mpc8360-qe-usb", "fsl,mpc8323-qe-usb";
+		reg = <0x6c0 0x40 0x8b00 0x100>;
+		interrupts = <11>;
+		interrupt-parent = <&qeic>;
+		fsl,fullspeed-clock = "clk21";
+		gpios = <&qe_pio_b  2 0 /* USBOE */
+			 &qe_pio_b  3 0 /* USBTP */
+			 &qe_pio_b  8 0 /* USBTN */
+			 &qe_pio_b  9 0 /* USBRP */
+			 &qe_pio_b 11 0 /* USBRN */
+			 &qe_pio_e 20 0 /* SPEED */
+			 &qe_pio_e 21 0 /* POWER */>;
+	};
+
+    w) Freescale MCU with MPC8349E-mITX compatible firmware
+
+    Required properties:
+      - compatible : "fsl,<mcu-chip>-<board>", "fsl,mcu-mpc8349emitx";
+      - reg : should specify I2C address (0x0a).
+      - #gpio-cells : should be 2.
+      - gpio-controller : should be present;
+
+    Example:
+
+	mcu_pio: mcu@0a {
+		#gpio-cells = <2>;
+		compatible = "fsl,mc9s08qg8-mpc8349emitx",
+			     "fsl,mcu-mpc8349emitx";
+		reg = <0x0a>;
+		gpio-controller;
+	};
+
+    x) Freescale Localbus UPM programmed to work with NAND flash
+
+      Required properties:
+      - compatible : "fsl,upm-nand".
+      - reg : should specify localbus chip select and size used for the chip.
+      - fsl,upm-addr-offset : UPM pattern offset for the address latch.
+      - fsl,upm-cmd-offset : UPM pattern offset for the command latch.
+      - gpios : may specify optional GPIO connected to the Ready-Not-Busy pin.
+
+      Example:
+
+	upm@1,0 {
+		compatible = "fsl,upm-nand";
+		reg = <1 0 1>;
+		fsl,upm-addr-offset = <16>;
+		fsl,upm-cmd-offset = <8>;
+		gpios = <&qe_pio_e 18 0>;
+
+		flash {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "...";
+
+			partition@0 {
+				...
+			};
+		};
+	};
+
+    y) LEDs on GPIOs
+
+    Required properties:
+      - compatible : should be "gpio-led".
+      - label : (optional) the label for this LED. If omitted, the label is
+        taken from the node name (excluding the unit address).
+      - gpios : should specify LED GPIO.
+
+    Example:
+
+	led@0 {
+		compatible = "gpio-led";
+		label = "hdd";
+		gpios = <&mcu_pio 0 1>;
+	};
+
+	led@1 {
+		compatible = "gpio-led";
+		label = "pwr";
+		gpios = <&mcu_pio 1 0>;
+	};
+
 VII - Marvell Discovery mv64[345]6x System Controller chips
 ===========================================================
 
-- 
1.5.5.4

Re: [PATCH] powerpc: add FHCI USB, FSL MCU, FSL UPM and GPIO LEDs bindings

[Kumar Gala]

On Jul 3, 2008, at 12:48 PM, Anton Vorontsov wrote:

> This patch adds few bindings for the new drivers to be submitted  
> through
> the appropriate maintainers.
>
> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
> ---
>
> Segher, thanks for the comments on the previous version. Do you see  
> any
> issues with this one or anything I could improve further?
>
> And if there are no issues... Kumar, could you apply this for  
> powerpc-next?
>
> Thanks.
>
> Documentation/powerpc/booting-without-of.txt |  111 +++++++++++++++++ 
> +++++++++
> 1 files changed, 111 insertions(+), 0 deletions(-)
>
> diff --git a/Documentation/powerpc/booting-without-of.txt b/ 
> Documentation/powerpc/booting-without-of.txt
> index b68684d..a7ea549 100644
> --- a/Documentation/powerpc/booting-without-of.txt
> +++ b/Documentation/powerpc/booting-without-of.txt
> @@ -62,6 +62,10 @@ Table of Contents
>       s) Freescale on board FPGA
>       t) Freescael MSI interrupt controller
>       u) Freescale General-purpose Timers Module
> +      v) Freescale QUICC Engine USB Controller
> +      w) Freescale MCU with MPC8349E-mITX compatible firmware

MCU doesn't mean much to me.  Its good to expand out the acronym at  
least once.

- k

Re: [PATCH] powerpc: add FHCI USB, FSL MCU, FSL UPM and GPIO LEDs bindings

[Anton Vorontsov]

On Thu, Jul 03, 2008 at 12:50:01PM -0500, Kumar Gala wrote:
>
> On Jul 3, 2008, at 12:48 PM, Anton Vorontsov wrote:
>
>> This patch adds few bindings for the new drivers to be submitted  
>> through
>> the appropriate maintainers.
>>
>> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
>> ---
>>
>> Segher, thanks for the comments on the previous version. Do you see  
>> any
>> issues with this one or anything I could improve further?
>>
>> And if there are no issues... Kumar, could you apply this for  
>> powerpc-next?
>>
>> Thanks.
>>
>> Documentation/powerpc/booting-without-of.txt |  111 +++++++++++++++++ 
>> +++++++++
>> 1 files changed, 111 insertions(+), 0 deletions(-)
>>
>> diff --git a/Documentation/powerpc/booting-without-of.txt b/ 
>> Documentation/powerpc/booting-without-of.txt
>> index b68684d..a7ea549 100644
>> --- a/Documentation/powerpc/booting-without-of.txt
>> +++ b/Documentation/powerpc/booting-without-of.txt
>> @@ -62,6 +62,10 @@ Table of Contents
>>       s) Freescale on board FPGA
>>       t) Freescael MSI interrupt controller
>>       u) Freescale General-purpose Timers Module
>> +      v) Freescale QUICC Engine USB Controller
>> +      w) Freescale MCU with MPC8349E-mITX compatible firmware
>
> MCU doesn't mean much to me.  Its good to expand out the acronym at  
> least once.

MCU stands for MicroController Unit, and even expanded this doesn't
mean much to anybody. :-) Freescale documentation names it as boards'
"MCU Subsystem", that is, the chip provides fan control, GPIOs,
software halt, etc. Basically, it is boards' power management companion
chip. I don't know how to name it more correctly, so I adhered to
documentation's naming (they simply call it MCU).

^^ I'll add some of these words to the node description though.

Thanks,

-- 
Anton Vorontsov
email: cbouatmailru@gmail.com
irc://irc.freenode.net/bd2

Re: [PATCH] powerpc: add FHCI USB, FSL MCU, FSL UPM and GPIO LEDs bindings

[Kumar Gala]

On Jul 3, 2008, at 1:24 PM, Anton Vorontsov wrote:

> On Thu, Jul 03, 2008 at 12:50:01PM -0500, Kumar Gala wrote:
>>
>> On Jul 3, 2008, at 12:48 PM, Anton Vorontsov wrote:
>>
>>> This patch adds few bindings for the new drivers to be submitted
>>> through
>>> the appropriate maintainers.
>>>
>>> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
>>> ---
>>>
>>> Segher, thanks for the comments on the previous version. Do you see
>>> any
>>> issues with this one or anything I could improve further?
>>>
>>> And if there are no issues... Kumar, could you apply this for
>>> powerpc-next?
>>>
>>> Thanks.
>>>
>>> Documentation/powerpc/booting-without-of.txt |  111 +++++++++++++++ 
>>> ++
>>> +++++++++
>>> 1 files changed, 111 insertions(+), 0 deletions(-)
>>>
>>> diff --git a/Documentation/powerpc/booting-without-of.txt b/
>>> Documentation/powerpc/booting-without-of.txt
>>> index b68684d..a7ea549 100644
>>> --- a/Documentation/powerpc/booting-without-of.txt
>>> +++ b/Documentation/powerpc/booting-without-of.txt
>>> @@ -62,6 +62,10 @@ Table of Contents
>>>      s) Freescale on board FPGA
>>>      t) Freescael MSI interrupt controller
>>>      u) Freescale General-purpose Timers Module
>>> +      v) Freescale QUICC Engine USB Controller
>>> +      w) Freescale MCU with MPC8349E-mITX compatible firmware
>>
>> MCU doesn't mean much to me.  Its good to expand out the acronym at
>> least once.
>
> MCU stands for MicroController Unit, and even expanded this doesn't
> mean much to anybody. :-) Freescale documentation names it as boards'
> "MCU Subsystem", that is, the chip provides fan control, GPIOs,
> software halt, etc. Basically, it is boards' power management  
> companion
> chip. I don't know how to name it more correctly, so I adhered to
> documentation's naming (they simply call it MCU).
>
> ^^ I'll add some of these words to the node description though.

I agree, but MicroController lets me a know a bit more than the random  
letters M-C-U.  Just one reference in the heading is sufficient.

- k

Re: [PATCH] powerpc: add FHCI USB, FSL MCU, FSL UPM and GPIO LEDs bindings

[Wolfgang Grandegger]

Hi Anton,

Anton Vorontsov wrote:
> This patch adds few bindings for the new drivers to be submitted through
> the appropriate maintainers.
> 
> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
> ---
> 
> Segher, thanks for the comments on the previous version. Do you see any
> issues with this one or anything I could improve further?
> 
> And if there are no issues... Kumar, could you apply this for powerpc-next?

As you know, I have some additions to your bindings and I posted a patch 
recently:

   http://ozlabs.org/pipermail/linuxppc-dev/2008-June/058617.html

Segher did not comment yet, maybe you would like to have a look. And do 
you have some news about the corresponding NAND support from the MTD people?

I really appreciate breaking booting-without-of.txt up. Will this happen 
already for powerpc-next (for 2.6.27)?

Thanks,

Wolfgang.

[PATCH v2] powerpc: add FHCI USB, FSL MCU, FSL UPM and GPIO LEDs bindings

[Anton Vorontsov]

This patch adds few bindings for the new drivers to be submitted through
the appropriate maintainers.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---

Updated to decrypt MCU, and to split the bindings into appropriate files.

 .../powerpc/device-tree/fsl/mcu-mpc8349emitx.txt   |   17 +++++++++
 Documentation/powerpc/device-tree/fsl/qe/usb.txt   |   37 ++++++++++++++++++++
 Documentation/powerpc/device-tree/fsl/upm-nand.txt |   28 +++++++++++++++
 Documentation/powerpc/device-tree/gpio/led.txt     |   15 ++++++++
 4 files changed, 97 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/powerpc/device-tree/fsl/mcu-mpc8349emitx.txt
 create mode 100644 Documentation/powerpc/device-tree/fsl/qe/usb.txt
 create mode 100644 Documentation/powerpc/device-tree/fsl/upm-nand.txt
 create mode 100644 Documentation/powerpc/device-tree/gpio/led.txt

diff --git a/Documentation/powerpc/device-tree/fsl/mcu-mpc8349emitx.txt b/Documentation/powerpc/device-tree/fsl/mcu-mpc8349emitx.txt
new file mode 100644
index 0000000..0f76633
--- /dev/null
+++ b/Documentation/powerpc/device-tree/fsl/mcu-mpc8349emitx.txt
@@ -0,0 +1,17 @@
+Freescale MPC8349E-mITX-compatible Power Management Micro Controller Unit (MCU)
+
+Required properties:
+- compatible : "fsl,<mcu-chip>-<board>", "fsl,mcu-mpc8349emitx".
+- reg : should specify I2C address (0x0a).
+- #gpio-cells : should be 2.
+- gpio-controller : should be present.
+
+Example:
+
+mcu@0a {
+	#gpio-cells = <2>;
+	compatible = "fsl,mc9s08qg8-mpc8349emitx",
+		     "fsl,mcu-mpc8349emitx";
+	reg = <0x0a>;
+	gpio-controller;
+};
diff --git a/Documentation/powerpc/device-tree/fsl/qe/usb.txt b/Documentation/powerpc/device-tree/fsl/qe/usb.txt
new file mode 100644
index 0000000..9ccd5f3
--- /dev/null
+++ b/Documentation/powerpc/device-tree/fsl/qe/usb.txt
@@ -0,0 +1,37 @@
+Freescale QUICC Engine USB Controller
+
+Required properties:
+- compatible : should be "fsl,<chip>-qe-usb", "fsl,mpc8323-qe-usb".
+- reg : the first two cells should contain usb registers location and
+  length, the next two two cells should contain PRAM location and
+  length.
+- interrupts : should contain USB interrupt.
+- interrupt-parent : interrupt source phandle.
+- fsl,fullspeed-clock : specifies the full speed USB clock source:
+  "none": clock source is disabled
+  "brg1" through "brg16": clock source is BRG1-BRG16, respectively
+  "clk1" through "clk24": clock source is CLK1-CLK24, respectively
+- fsl,lowspeed-clock : specifies the low speed USB clock source:
+  "none": clock source is disabled
+  "brg1" through "brg16": clock source is BRG1-BRG16, respectively
+  "clk1" through "clk24": clock source is CLK1-CLK24, respectively
+- hub-power-budget : USB power budget for the root hub, in mA.
+- gpios : should specify GPIOs in this order: USBOE, USBTP, USBTN, USBRP,
+  USBRN, SPEED (optional), and POWER (optional).
+
+Example:
+
+usb@6c0 {
+	compatible = "fsl,mpc8360-qe-usb", "fsl,mpc8323-qe-usb";
+	reg = <0x6c0 0x40 0x8b00 0x100>;
+	interrupts = <11>;
+	interrupt-parent = <&qeic>;
+	fsl,fullspeed-clock = "clk21";
+	gpios = <&qe_pio_b  2 0 /* USBOE */
+		 &qe_pio_b  3 0 /* USBTP */
+		 &qe_pio_b  8 0 /* USBTN */
+		 &qe_pio_b  9 0 /* USBRP */
+		 &qe_pio_b 11 0 /* USBRN */
+		 &qe_pio_e 20 0 /* SPEED */
+		 &qe_pio_e 21 0 /* POWER */>;
+};
diff --git a/Documentation/powerpc/device-tree/fsl/upm-nand.txt b/Documentation/powerpc/device-tree/fsl/upm-nand.txt
new file mode 100644
index 0000000..84a04d5
--- /dev/null
+++ b/Documentation/powerpc/device-tree/fsl/upm-nand.txt
@@ -0,0 +1,28 @@
+Freescale Localbus UPM programmed to work with NAND flash
+
+Required properties:
+- compatible : "fsl,upm-nand".
+- reg : should specify localbus chip select and size used for the chip.
+- fsl,upm-addr-offset : UPM pattern offset for the address latch.
+- fsl,upm-cmd-offset : UPM pattern offset for the command latch.
+- gpios : may specify optional GPIO connected to the Ready-Not-Busy pin.
+
+Example:
+
+upm@1,0 {
+	compatible = "fsl,upm-nand";
+	reg = <1 0 1>;
+	fsl,upm-addr-offset = <16>;
+	fsl,upm-cmd-offset = <8>;
+	gpios = <&qe_pio_e 18 0>;
+
+	flash {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "...";
+
+		partition@0 {
+			...
+		};
+	};
+};
diff --git a/Documentation/powerpc/device-tree/gpio/led.txt b/Documentation/powerpc/device-tree/gpio/led.txt
new file mode 100644
index 0000000..ff51f4c
--- /dev/null
+++ b/Documentation/powerpc/device-tree/gpio/led.txt
@@ -0,0 +1,15 @@
+LED connected to GPIO
+
+Required properties:
+- compatible : should be "gpio-led".
+- label : (optional) the label for this LED. If omitted, the label is
+  taken from the node name (excluding the unit address).
+- gpios : should specify LED GPIO.
+
+Example:
+
+led@0 {
+	compatible = "gpio-led";
+	label = "hdd";
+	gpios = <&mcu_pio 0 1>;
+};
-- 
1.5.5.4

Re: [PATCH v2] powerpc: add FHCI USB, FSL MCU, FSL UPM and GPIO LEDs bindings

[Kumar Gala]

On Jul 4, 2008, at 11:53 AM, Anton Vorontsov wrote:

> This patch adds few bindings for the new drivers to be submitted  
> through
> the appropriate maintainers.
>
> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
> ---
>
> Updated to decrypt MCU, and to split the bindings into appropriate  
> files.
>
> .../powerpc/device-tree/fsl/mcu-mpc8349emitx.txt   |   17 +++++++++
> Documentation/powerpc/device-tree/fsl/qe/usb.txt   |   37 +++++++++++ 
> +++++++++
> Documentation/powerpc/device-tree/fsl/upm-nand.txt |   28 +++++++++++ 
> ++++
> Documentation/powerpc/device-tree/gpio/led.txt     |   15 ++++++++
> 4 files changed, 97 insertions(+), 0 deletions(-)
> create mode 100644 Documentation/powerpc/device-tree/fsl/mcu- 
> mpc8349emitx.txt
> create mode 100644 Documentation/powerpc/device-tree/fsl/qe/usb.txt
> create mode 100644 Documentation/powerpc/device-tree/fsl/upm-nand.txt
> create mode 100644 Documentation/powerpc/device-tree/gpio/led.txt

applied.

- k

Re: [PATCH v2] powerpc: add FHCI USB, FSL MCU, FSL UPM and GPIO LEDs bindings

[Anton Vorontsov]

On Tue, Jul 15, 2008 at 08:21:38AM -0500, Kumar Gala wrote:
>
> On Jul 4, 2008, at 11:53 AM, Anton Vorontsov wrote:
>
>> This patch adds few bindings for the new drivers to be submitted  
>> through
>> the appropriate maintainers.
>>
>> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
>> ---
>>
>> Updated to decrypt MCU, and to split the bindings into appropriate  
>> files.
>>
>> .../powerpc/device-tree/fsl/mcu-mpc8349emitx.txt   |   17 +++++++++
>> Documentation/powerpc/device-tree/fsl/qe/usb.txt   |   37 +++++++++++ 
>> +++++++++
>> Documentation/powerpc/device-tree/fsl/upm-nand.txt |   28 +++++++++++ 
>> ++++
>> Documentation/powerpc/device-tree/gpio/led.txt     |   15 ++++++++
>> 4 files changed, 97 insertions(+), 0 deletions(-)
>> create mode 100644 Documentation/powerpc/device-tree/fsl/mcu- 
>> mpc8349emitx.txt
>> create mode 100644 Documentation/powerpc/device-tree/fsl/qe/usb.txt
>> create mode 100644 Documentation/powerpc/device-tree/fsl/upm-nand.txt
>> create mode 100644 Documentation/powerpc/device-tree/gpio/led.txt
>
> applied.

Ugh, you fixed bindings' directory in Jochen's CPM patch, but not in
my patch:

commit 91993d56812fd09b6cccea12d3c83df623cb0ea6
Author: Anton Vorontsov <avorontsov@ru.mvista.com>
Date:   Fri Jul 4 20:53:28 2008 +0400

    powerpc: add FHCI USB, FSL MCU, FSL UPM and GPIO LEDs bindings
    
    This patch adds few bindings for the new drivers to be submitted through
    the appropriate maintainers.
    
    Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
    Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

diff --git a/Documentation/powerpc/device-tree/fsl/mcu-mpc8349emitx.txt b/Documentation/powerpc/device-tree/fsl/mcu-mpc8349emit
new file mode 100644
index 0000000..0f76633
--- /dev/null
+++ b/Documentation/powerpc/device-tree/fsl/mcu-mpc8349emitx.txt
....

-- 
Anton Vorontsov
email: cbouatmailru@gmail.com
irc://irc.freenode.net/bd2

Re: [PATCH v2] powerpc: add FHCI USB, FSL MCU, FSL UPM and GPIO LEDs bindings

[Kumar Gala]

>>
> Ugh, you fixed bindings' directory in Jochen's CPM patch, but not in
> my patch:
>
> commit 91993d56812fd09b6cccea12d3c83df623cb0ea6
> Author: Anton Vorontsov <avorontsov@ru.mvista.com>
> Date:   Fri Jul 4 20:53:28 2008 +0400
>
>    powerpc: add FHCI USB, FSL MCU, FSL UPM and GPIO LEDs bindings
>
>    This patch adds few bindings for the new drivers to be submitted  
> through
>    the appropriate maintainers.
>
>    Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
>    Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
>
> diff --git a/Documentation/powerpc/device-tree/fsl/mcu- 
> mpc8349emitx.txt b/Documentation/powerpc/device-tree/fsl/mcu- 
> mpc8349emit
> new file mode 100644
> index 0000000..0f76633
> --- /dev/null
> +++ b/Documentation/powerpc/device-tree/fsl/mcu-mpc8349emitx.txt
> ....

duh.  will fix it up.

- k

Re: [PATCH v2] powerpc: add FHCI USB, FSL MCU, FSL UPM and GPIO LEDs bindings

[Kumar Gala]

>>
> Ugh, you fixed bindings' directory in Jochen's CPM patch, but not in
> my patch:
>
> commit 91993d56812fd09b6cccea12d3c83df623cb0ea6
> Author: Anton Vorontsov <avorontsov@ru.mvista.com>
> Date:   Fri Jul 4 20:53:28 2008 +0400
>
>    powerpc: add FHCI USB, FSL MCU, FSL UPM and GPIO LEDs bindings
>
>    This patch adds few bindings for the new drivers to be submitted  
> through
>    the appropriate maintainers.
>
>    Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
>    Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
>
> diff --git a/Documentation/powerpc/device-tree/fsl/mcu- 
> mpc8349emitx.txt b/Documentation/powerpc/device-tree/fsl/mcu- 
> mpc8349emit
> new file mode 100644
> index 0000000..0f76633
> --- /dev/null
> +++ b/Documentation/powerpc/device-tree/fsl/mcu-mpc8349emitx.txt
> ....

Rebased the tree and fixed it.  Can you look over the files and make  
sure everything looks ok.  (I'm partially concerned about the QE usb  
node).

- k

Re: [PATCH v2] powerpc: add FHCI USB, FSL MCU, FSL UPM and GPIO LEDs bindings

[Anton Vorontsov]

On Tue, Jul 15, 2008 at 11:23:42AM -0500, Kumar Gala wrote:
>>>
>> Ugh, you fixed bindings' directory in Jochen's CPM patch, but not in
>> my patch:
>>
>> commit 91993d56812fd09b6cccea12d3c83df623cb0ea6
>> Author: Anton Vorontsov <avorontsov@ru.mvista.com>
>> Date:   Fri Jul 4 20:53:28 2008 +0400
>>
>>    powerpc: add FHCI USB, FSL MCU, FSL UPM and GPIO LEDs bindings
>>
>>    This patch adds few bindings for the new drivers to be submitted  
>> through
>>    the appropriate maintainers.
>>
>>    Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
>>    Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
>>
>> diff --git a/Documentation/powerpc/device-tree/fsl/mcu- 
>> mpc8349emitx.txt b/Documentation/powerpc/device-tree/fsl/mcu- 
>> mpc8349emit
>> new file mode 100644
>> index 0000000..0f76633
>> --- /dev/null
>> +++ b/Documentation/powerpc/device-tree/fsl/mcu-mpc8349emitx.txt
>> ....
>
> Rebased the tree and fixed it.  Can you look over the files and make  
> sure everything looks ok.  (I'm partially concerned about the QE usb  
> node).

Yes, everything looks fine. b-w-of specified old QE USB bindings,
and no single driver actually used them.

Thanks,

-- 
Anton Vorontsov
email: cbouatmailru@gmail.com
irc://irc.freenode.net/bd2