From: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To: jeff@garzik.org, davem@davemloft.net
Cc: bunk@kernel.org, e1000-devel@lists.sourceforge.net,
tiwai@suse.de, netdev@vger.kernel.org,
maciej.sosnowski@intel.com, linux-kernel@vger.kernel.org,
linuxppc-dev@ozlabs.org, brice@myri.com,
dan.j.williams@intel.com, sam@ravnborg.org,
akpm@linux-foundation.org,
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Subject: [PATCH] igb: add IGB_DCA instead of selecting INTEL_IOATDMA
Date: Fri, 17 Oct 2008 11:08:31 -0700 [thread overview]
Message-ID: <20081017180831.15639.50705.stgit@gitlost.lost> (raw)
Add a bool IGB_DCA defined to y if IGB and DCA are enabled, but IGB isn't y while DCA=m. And thus remove the need to select INTEL_IOATDMA when IGB is enabled, so that non-x86 architectures can build the igb driver.
Based on work/patch from Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/Kconfig | 5 +++++
drivers/net/igb/igb_main.c | 32 ++++++++++++++++----------------
2 files changed, 21 insertions(+), 16 deletions(-)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index ad301ac..588ef13 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -2003,6 +2003,11 @@ config IGB_LRO
If in doubt, say N.
+config IGB_DCA
+ bool "Enable DCA"
+ default y
+ depends on IGB && DCA && !(IGB=y && DCA=m)
+
source "drivers/net/ixp2000/Kconfig"
config MYRI_SBUS
diff --git a/drivers/net/igb/igb_main.c b/drivers/net/igb/igb_main.c
index 53cbeae..2bd3629 100644
--- a/drivers/net/igb/igb_main.c
+++ b/drivers/net/igb/igb_main.c
@@ -41,7 +41,7 @@
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/if_ether.h>
-#ifdef CONFIG_DCA
+#ifdef CONFIG_IGB_DCA
#include <linux/dca.h>
#endif
#include "igb.h"
@@ -106,11 +106,11 @@ static irqreturn_t igb_msix_other(int irq, void *);
static irqreturn_t igb_msix_rx(int irq, void *);
static irqreturn_t igb_msix_tx(int irq, void *);
static int igb_clean_rx_ring_msix(struct napi_struct *, int);
-#ifdef CONFIG_DCA
+#ifdef CONFIG_IGB_DCA
static void igb_update_rx_dca(struct igb_ring *);
static void igb_update_tx_dca(struct igb_ring *);
static void igb_setup_dca(struct igb_adapter *);
-#endif /* CONFIG_DCA */
+#endif /* CONFIG_IGB_DCA */
static bool igb_clean_tx_irq(struct igb_ring *);
static int igb_poll(struct napi_struct *, int);
static bool igb_clean_rx_irq_adv(struct igb_ring *, int *, int);
@@ -131,7 +131,7 @@ static int igb_suspend(struct pci_dev *, pm_message_t);
static int igb_resume(struct pci_dev *);
#endif
static void igb_shutdown(struct pci_dev *);
-#ifdef CONFIG_DCA
+#ifdef CONFIG_IGB_DCA
static int igb_notify_dca(struct notifier_block *, unsigned long, void *);
static struct notifier_block dca_notifier = {
.notifier_call = igb_notify_dca,
@@ -207,7 +207,7 @@ static int __init igb_init_module(void)
global_quad_port_a = 0;
ret = pci_register_driver(&igb_driver);
-#ifdef CONFIG_DCA
+#ifdef CONFIG_IGB_DCA
dca_register_notify(&dca_notifier);
#endif
return ret;
@@ -223,7 +223,7 @@ module_init(igb_init_module);
**/
static void __exit igb_exit_module(void)
{
-#ifdef CONFIG_DCA
+#ifdef CONFIG_IGB_DCA
dca_unregister_notify(&dca_notifier);
#endif
pci_unregister_driver(&igb_driver);
@@ -1260,7 +1260,7 @@ static int __devinit igb_probe(struct pci_dev *pdev,
if (err)
goto err_register;
-#ifdef CONFIG_DCA
+#ifdef CONFIG_IGB_DCA
if ((adapter->flags & IGB_FLAG_HAS_DCA) &&
(dca_add_requester(&pdev->dev) == 0)) {
adapter->flags |= IGB_FLAG_DCA_ENABLED;
@@ -1334,7 +1334,7 @@ static void __devexit igb_remove(struct pci_dev *pdev)
{
struct net_device *netdev = pci_get_drvdata(pdev);
struct igb_adapter *adapter = netdev_priv(netdev);
-#ifdef CONFIG_DCA
+#ifdef CONFIG_IGB_DCA
struct e1000_hw *hw = &adapter->hw;
#endif
@@ -1346,7 +1346,7 @@ static void __devexit igb_remove(struct pci_dev *pdev)
flush_scheduled_work();
-#ifdef CONFIG_DCA
+#ifdef CONFIG_IGB_DCA
if (adapter->flags & IGB_FLAG_DCA_ENABLED) {
dev_info(&pdev->dev, "DCA disabled\n");
dca_remove_requester(&pdev->dev);
@@ -3294,7 +3294,7 @@ static irqreturn_t igb_msix_tx(int irq, void *data)
struct igb_adapter *adapter = tx_ring->adapter;
struct e1000_hw *hw = &adapter->hw;
-#ifdef CONFIG_DCA
+#ifdef CONFIG_IGB_DCA
if (adapter->flags & IGB_FLAG_DCA_ENABLED)
igb_update_tx_dca(tx_ring);
#endif
@@ -3346,14 +3346,14 @@ static irqreturn_t igb_msix_rx(int irq, void *data)
if (netif_rx_schedule_prep(adapter->netdev, &rx_ring->napi))
__netif_rx_schedule(adapter->netdev, &rx_ring->napi);
-#ifdef CONFIG_DCA
+#ifdef CONFIG_IGB_DCA
if (adapter->flags & IGB_FLAG_DCA_ENABLED)
igb_update_rx_dca(rx_ring);
#endif
return IRQ_HANDLED;
}
-#ifdef CONFIG_DCA
+#ifdef CONFIG_IGB_DCA
static void igb_update_rx_dca(struct igb_ring *rx_ring)
{
u32 dca_rxctrl;
@@ -3473,7 +3473,7 @@ static int igb_notify_dca(struct notifier_block *nb, unsigned long event,
return ret_val ? NOTIFY_BAD : NOTIFY_DONE;
}
-#endif /* CONFIG_DCA */
+#endif /* CONFIG_IGB_DCA */
/**
* igb_intr_msi - Interrupt Handler
@@ -3552,13 +3552,13 @@ static int igb_poll(struct napi_struct *napi, int budget)
int tx_clean_complete, work_done = 0;
/* this poll routine only supports one tx and one rx queue */
-#ifdef CONFIG_DCA
+#ifdef CONFIG_IGB_DCA
if (adapter->flags & IGB_FLAG_DCA_ENABLED)
igb_update_tx_dca(&adapter->tx_ring[0]);
#endif
tx_clean_complete = igb_clean_tx_irq(&adapter->tx_ring[0]);
-#ifdef CONFIG_DCA
+#ifdef CONFIG_IGB_DCA
if (adapter->flags & IGB_FLAG_DCA_ENABLED)
igb_update_rx_dca(&adapter->rx_ring[0]);
#endif
@@ -3586,7 +3586,7 @@ static int igb_clean_rx_ring_msix(struct napi_struct *napi, int budget)
struct net_device *netdev = adapter->netdev;
int work_done = 0;
-#ifdef CONFIG_DCA
+#ifdef CONFIG_IGB_DCA
if (adapter->flags & IGB_FLAG_DCA_ENABLED)
igb_update_rx_dca(rx_ring);
#endif
next reply other threads:[~2008-10-17 18:14 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-10-17 18:08 Jeff Kirsher [this message]
2008-10-21 6:11 ` [PATCH] igb: add IGB_DCA instead of selecting INTEL_IOATDMA Jeff Garzik
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20081017180831.15639.50705.stgit@gitlost.lost \
--to=jeffrey.t.kirsher@intel.com \
--cc=akpm@linux-foundation.org \
--cc=brice@myri.com \
--cc=bunk@kernel.org \
--cc=dan.j.williams@intel.com \
--cc=davem@davemloft.net \
--cc=e1000-devel@lists.sourceforge.net \
--cc=jeff@garzik.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linuxppc-dev@ozlabs.org \
--cc=maciej.sosnowski@intel.com \
--cc=netdev@vger.kernel.org \
--cc=sam@ravnborg.org \
--cc=tiwai@suse.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).