From: Anton Vorontsov <avorontsov@ru.mvista.com>
To: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev@ozlabs.org, Paul Mackerras <paulus@samba.org>,
Tony Li <tony.li@freescale.com>
Subject: [PATCH 4/4] powerpc/83xx: Add PCI-E support for all MPC83xx boards with PCI-E
Date: Mon, 29 Dec 2008 19:40:40 +0300 [thread overview]
Message-ID: <20081229164040.GD8215@oksana.dev.rtsoft.ru> (raw)
This patch adds pcie nodes to the appropriate dts files, plus adds
some probing code for the boards.
Note that the nodes are disabled by default (via status property),
since old (community) U-Boots don't configure PCI-E controllers.
Also, remove of_device_is_avaliable() check from the mpc837x_mds.c
board file, as mpc83xx_add_bridge() has the same check now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
arch/powerpc/boot/dts/mpc8315erdb.dts | 42 +++++++++++++++++++++++++++++
arch/powerpc/boot/dts/mpc8377_mds.dts | 42 +++++++++++++++++++++++++++++
arch/powerpc/boot/dts/mpc8377_rdb.dts | 42 +++++++++++++++++++++++++++++
arch/powerpc/boot/dts/mpc8378_mds.dts | 42 +++++++++++++++++++++++++++++
arch/powerpc/boot/dts/mpc8378_rdb.dts | 42 +++++++++++++++++++++++++++++
arch/powerpc/platforms/83xx/mpc831x_rdb.c | 2 +
arch/powerpc/platforms/83xx/mpc837x_mds.c | 10 ++-----
arch/powerpc/platforms/83xx/mpc837x_rdb.c | 2 +
8 files changed, 217 insertions(+), 7 deletions(-)
diff --git a/arch/powerpc/boot/dts/mpc8315erdb.dts b/arch/powerpc/boot/dts/mpc8315erdb.dts
index d3d3097..5997325 100644
--- a/arch/powerpc/boot/dts/mpc8315erdb.dts
+++ b/arch/powerpc/boot/dts/mpc8315erdb.dts
@@ -22,6 +22,8 @@
serial0 = &serial0;
serial1 = &serial1;
pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
};
cpus {
@@ -330,4 +332,44 @@
compatible = "fsl,mpc8349-pci";
device_type = "pci";
};
+
+ pci1: pcie@e0009000 {
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pcie";
+ compatible = "fsl,mpc8315-pcie", "fsl,mpc8314-pcie";
+ reg = <0xe0009000 0x00001000 0xb0000000 0x01000000>;
+ ranges = <0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xb1000000 0 0x00800000>;
+ bus-range = <0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <0 0 0 1 &ipic 1 8
+ 0 0 0 2 &ipic 1 8
+ 0 0 0 3 &ipic 1 8
+ 0 0 0 4 &ipic 1 8>;
+ clock-frequency = <0>;
+ /* cleared by u-boot */
+ status = "not configured";
+ };
+
+ pci2: pcie@e000a000 {
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pcie";
+ compatible = "fsl,mpc8315-pcie", "fsl,mpc8314-pcie";
+ reg = <0xe000a000 0x00001000 0xd0000000 0x01000000>;
+ ranges = <0x02000000 0 0xc0000000 0xc0000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xd1000000 0 0x00800000>;
+ bus-range = <0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <0 0 0 1 &ipic 2 8
+ 0 0 0 2 &ipic 2 8
+ 0 0 0 3 &ipic 2 8
+ 0 0 0 4 &ipic 2 8>;
+ clock-frequency = <0>;
+ /* cleared by u-boot */
+ status = "not configured";
+ };
};
diff --git a/arch/powerpc/boot/dts/mpc8377_mds.dts b/arch/powerpc/boot/dts/mpc8377_mds.dts
index 0484561..61c3303 100644
--- a/arch/powerpc/boot/dts/mpc8377_mds.dts
+++ b/arch/powerpc/boot/dts/mpc8377_mds.dts
@@ -23,6 +23,8 @@
serial0 = &serial0;
serial1 = &serial1;
pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
};
cpus {
@@ -390,4 +392,44 @@
compatible = "fsl,mpc8349-pci";
device_type = "pci";
};
+
+ pci1: pcie@e0009000 {
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pcie";
+ compatible = "fsl,mpc8377-pcie", "fsl,mpc8314-pcie";
+ reg = <0xe0009000 0x00001000 0xb0000000 0x01000000>;
+ ranges = <0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xb1000000 0 0x00800000>;
+ bus-range = <0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <0 0 0 1 &ipic 1 8
+ 0 0 0 2 &ipic 1 8
+ 0 0 0 3 &ipic 1 8
+ 0 0 0 4 &ipic 1 8>;
+ clock-frequency = <0>;
+ /* cleared by u-boot */
+ status = "not configured";
+ };
+
+ pci2: pcie@e000a000 {
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pcie";
+ compatible = "fsl,mpc8377-pcie", "fsl,mpc8314-pcie";
+ reg = <0xe000a000 0x00001000 0xd0000000 0x01000000>;
+ ranges = <0x02000000 0 0xc0000000 0xc0000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xd1000000 0 0x00800000>;
+ bus-range = <0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <0 0 0 1 &ipic 2 8
+ 0 0 0 2 &ipic 2 8
+ 0 0 0 3 &ipic 2 8
+ 0 0 0 4 &ipic 2 8>;
+ clock-frequency = <0>;
+ /* cleared by u-boot */
+ status = "not configured";
+ };
};
diff --git a/arch/powerpc/boot/dts/mpc8377_rdb.dts b/arch/powerpc/boot/dts/mpc8377_rdb.dts
index 9fe8e4c..54baea7 100644
--- a/arch/powerpc/boot/dts/mpc8377_rdb.dts
+++ b/arch/powerpc/boot/dts/mpc8377_rdb.dts
@@ -22,6 +22,8 @@
serial0 = &serial0;
serial1 = &serial1;
pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
};
cpus {
@@ -331,4 +333,44 @@
compatible = "fsl,mpc8349-pci";
device_type = "pci";
};
+
+ pci1: pcie@e0009000 {
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pcie";
+ compatible = "fsl,mpc8377-pcie", "fsl,mpc8314-pcie";
+ reg = <0xe0009000 0x00001000 0xb0000000 0x01000000>;
+ ranges = <0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xb1000000 0 0x00800000>;
+ bus-range = <0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <0 0 0 1 &ipic 1 8
+ 0 0 0 2 &ipic 1 8
+ 0 0 0 3 &ipic 1 8
+ 0 0 0 4 &ipic 1 8>;
+ clock-frequency = <0>;
+ /* cleared by u-boot */
+ status = "not configured";
+ };
+
+ pci2: pcie@e000a000 {
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pcie";
+ compatible = "fsl,mpc8377-pcie", "fsl,mpc8314-pcie";
+ reg = <0xe000a000 0x00001000 0xd0000000 0x01000000>;
+ ranges = <0x02000000 0 0xc0000000 0xc0000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xd1000000 0 0x00800000>;
+ bus-range = <0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <0 0 0 1 &ipic 2 8
+ 0 0 0 2 &ipic 2 8
+ 0 0 0 3 &ipic 2 8
+ 0 0 0 4 &ipic 2 8>;
+ clock-frequency = <0>;
+ /* cleared by u-boot */
+ status = "not configured";
+ };
};
diff --git a/arch/powerpc/boot/dts/mpc8378_mds.dts b/arch/powerpc/boot/dts/mpc8378_mds.dts
index 67a08d2..cc66008 100644
--- a/arch/powerpc/boot/dts/mpc8378_mds.dts
+++ b/arch/powerpc/boot/dts/mpc8378_mds.dts
@@ -23,6 +23,8 @@
serial0 = &serial0;
serial1 = &serial1;
pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
};
cpus {
@@ -376,4 +378,44 @@
compatible = "fsl,mpc8349-pci";
device_type = "pci";
};
+
+ pci1: pcie@e0009000 {
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pcie";
+ compatible = "fsl,mpc8378-pcie", "fsl,mpc8314-pcie";
+ reg = <0xe0009000 0x00001000 0xb0000000 0x01000000>;
+ ranges = <0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xb1000000 0 0x00800000>;
+ bus-range = <0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <0 0 0 1 &ipic 1 8
+ 0 0 0 2 &ipic 1 8
+ 0 0 0 3 &ipic 1 8
+ 0 0 0 4 &ipic 1 8>;
+ clock-frequency = <0>;
+ /* cleared by u-boot */
+ status = "not configured";
+ };
+
+ pci2: pcie@e000a000 {
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pcie";
+ compatible = "fsl,mpc8378-pcie", "fsl,mpc8314-pcie";
+ reg = <0xe000a000 0x00001000 0xd0000000 0x01000000>;
+ ranges = <0x02000000 0 0xc0000000 0xc0000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xd1000000 0 0x00800000>;
+ bus-range = <0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <0 0 0 1 &ipic 2 8
+ 0 0 0 2 &ipic 2 8
+ 0 0 0 3 &ipic 2 8
+ 0 0 0 4 &ipic 2 8>;
+ clock-frequency = <0>;
+ /* cleared by u-boot */
+ status = "not configured";
+ };
};
diff --git a/arch/powerpc/boot/dts/mpc8378_rdb.dts b/arch/powerpc/boot/dts/mpc8378_rdb.dts
index 3a6d528..ab89f8f 100644
--- a/arch/powerpc/boot/dts/mpc8378_rdb.dts
+++ b/arch/powerpc/boot/dts/mpc8378_rdb.dts
@@ -22,6 +22,8 @@
serial0 = &serial0;
serial1 = &serial1;
pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
};
cpus {
@@ -317,4 +319,44 @@
compatible = "fsl,mpc8349-pci";
device_type = "pci";
};
+
+ pci1: pcie@e0009000 {
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pcie";
+ compatible = "fsl,mpc8378-pcie", "fsl,mpc8314-pcie";
+ reg = <0xe0009000 0x00001000 0xb0000000 0x01000000>;
+ ranges = <0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xb1000000 0 0x00800000>;
+ bus-range = <0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <0 0 0 1 &ipic 1 8
+ 0 0 0 2 &ipic 1 8
+ 0 0 0 3 &ipic 1 8
+ 0 0 0 4 &ipic 1 8>;
+ clock-frequency = <0>;
+ /* cleared by u-boot */
+ status = "not configured";
+ };
+
+ pci2: pcie@e000a000 {
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pcie";
+ compatible = "fsl,mpc8378-pcie", "fsl,mpc8314-pcie";
+ reg = <0xe000a000 0x00001000 0xd0000000 0x01000000>;
+ ranges = <0x02000000 0 0xc0000000 0xc0000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xd1000000 0 0x00800000>;
+ bus-range = <0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <0 0 0 1 &ipic 2 8
+ 0 0 0 2 &ipic 2 8
+ 0 0 0 3 &ipic 2 8
+ 0 0 0 4 &ipic 2 8>;
+ clock-frequency = <0>;
+ /* cleared by u-boot */
+ status = "not configured";
+ };
};
diff --git a/arch/powerpc/platforms/83xx/mpc831x_rdb.c b/arch/powerpc/platforms/83xx/mpc831x_rdb.c
index 5177bdd..821b11b 100644
--- a/arch/powerpc/platforms/83xx/mpc831x_rdb.c
+++ b/arch/powerpc/platforms/83xx/mpc831x_rdb.c
@@ -38,6 +38,8 @@ static void __init mpc831x_rdb_setup_arch(void)
#ifdef CONFIG_PCI
for_each_compatible_node(np, "pci", "fsl,mpc8349-pci")
mpc83xx_add_bridge(np);
+ for_each_compatible_node(np, "pcie", "fsl,mpc8314-pcie")
+ mpc83xx_add_bridge(np);
#endif
mpc831x_usb_cfg();
}
diff --git a/arch/powerpc/platforms/83xx/mpc837x_mds.c b/arch/powerpc/platforms/83xx/mpc837x_mds.c
index 530ef99..a8593f2 100644
--- a/arch/powerpc/platforms/83xx/mpc837x_mds.c
+++ b/arch/powerpc/platforms/83xx/mpc837x_mds.c
@@ -84,14 +84,10 @@ static void __init mpc837x_mds_setup_arch(void)
ppc_md.progress("mpc837x_mds_setup_arch()", 0);
#ifdef CONFIG_PCI
- for_each_compatible_node(np, "pci", "fsl,mpc8349-pci") {
- if (!of_device_is_available(np)) {
- pr_warning("%s: disabled by the firmware.\n",
- np->full_name);
- continue;
- }
+ for_each_compatible_node(np, "pci", "fsl,mpc8349-pci")
+ mpc83xx_add_bridge(np);
+ for_each_compatible_node(np, "pcie", "fsl,mpc8314-pcie")
mpc83xx_add_bridge(np);
- }
#endif
mpc837xmds_usb_cfg();
}
diff --git a/arch/powerpc/platforms/83xx/mpc837x_rdb.c b/arch/powerpc/platforms/83xx/mpc837x_rdb.c
index 1d09654..011b4c4 100644
--- a/arch/powerpc/platforms/83xx/mpc837x_rdb.c
+++ b/arch/powerpc/platforms/83xx/mpc837x_rdb.c
@@ -38,6 +38,8 @@ static void __init mpc837x_rdb_setup_arch(void)
#ifdef CONFIG_PCI
for_each_compatible_node(np, "pci", "fsl,mpc8349-pci")
mpc83xx_add_bridge(np);
+ for_each_compatible_node(np, "pcie", "fsl,mpc8314-pcie")
+ mpc83xx_add_bridge(np);
#endif
mpc837x_usb_cfg();
}
--
1.5.6.5
next reply other threads:[~2008-12-29 16:40 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-12-29 16:40 Anton Vorontsov [this message]
2008-12-30 17:46 ` [PATCH 4/4] powerpc/83xx: Add PCI-E support for all MPC83xx boards with PCI-E Kumar Gala
2008-12-30 20:19 ` [PATCH v2 " Anton Vorontsov
2008-12-31 16:48 ` Kumar Gala
2008-12-31 17:10 ` Wolfgang Denk
2009-01-01 14:26 ` Kumar Gala
2009-01-05 17:46 ` Scott Wood
2009-01-05 18:01 ` Anton Vorontsov
2009-01-06 12:18 ` Leon Woestenberg
2009-01-07 15:43 ` Scott Wood
2009-01-06 18:53 ` Leon Woestenberg
2009-01-06 19:27 ` Anton Vorontsov
2009-01-06 20:38 ` Kumar Gala
2009-01-06 21:15 ` Anton Vorontsov
2009-01-06 22:33 ` Leon Woestenberg
2009-01-06 23:42 ` Anton Vorontsov
2009-01-07 0:40 ` Leon Woestenberg
2008-12-31 17:41 ` Anton Vorontsov
2009-01-01 14:29 ` Kumar Gala
2009-01-05 16:37 ` Anton Vorontsov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20081229164040.GD8215@oksana.dev.rtsoft.ru \
--to=avorontsov@ru.mvista.com \
--cc=galak@kernel.crashing.org \
--cc=linuxppc-dev@ozlabs.org \
--cc=paulus@samba.org \
--cc=tony.li@freescale.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).