linuxppc-dev.lists.ozlabs.org archive mirror
 help / color / mirror / Atom feed
From: Anton Vorontsov <avorontsov@ru.mvista.com>
To: Pierre Ossman <drzeus-sdhci@drzeus.cx>
Cc: Ben Dooks <ben-linux@fluff.org>, Arnd Bergmann <arnd@arndb.de>,
	Liu Dave <DaveLiu@freescale.com>,
	linux-kernel@vger.kernel.org, linuxppc-dev@ozlabs.org,
	sdhci-devel@list.drzeus.cx
Subject: [PATCH 12/13] sdhci: Add quirk for controllers with max. block size up to 4096 bytes
Date: Fri, 13 Feb 2009 17:47:39 +0300	[thread overview]
Message-ID: <20090213144739.GL23889@oksana.dev.rtsoft.ru> (raw)
In-Reply-To: <20090213144630.GA13436@oksana.dev.rtsoft.ru>

FSL eSDHC controllers can support maximum block size up to 4096
bytes. The MBL (Maximum Block Length) field in the capabilities
register extended by one bit, and bits 13:15 in the block size
register reserved.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
 drivers/mmc/host/sdhci.c |   28 ++++++++++++++++++++--------
 drivers/mmc/host/sdhci.h |    2 ++
 2 files changed, 22 insertions(+), 8 deletions(-)

diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index b308dbf..b341a9a 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -682,6 +682,7 @@ static void sdhci_set_transfer_irqs(struct sdhci_host *host)
 
 static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data)
 {
+	u16 blksz;
 	u8 count;
 	u8 ctrl;
 	int ret;
@@ -831,7 +832,12 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data)
 	sdhci_set_transfer_irqs(host);
 
 	/* We do not handle DMA boundaries, so set it to max (512 KiB) */
-	sdhci_writew(host, SDHCI_MAKE_BLKSZ(7, data->blksz), SDHCI_BLOCK_SIZE);
+	if (host->quirks & SDHCI_QUIRK_MAX_BLK_SZ_4096)
+		blksz = data->blksz;
+	else
+		blksz = SDHCI_MAKE_BLKSZ(7, data->blksz);
+
+	sdhci_writew(host, blksz, SDHCI_BLOCK_SIZE);
 	sdhci_writew(host, data->blocks, SDHCI_BLOCK_COUNT);
 }
 
@@ -1840,13 +1846,19 @@ int sdhci_add_host(struct sdhci_host *host)
 	 * Maximum block size. This varies from controller to controller and
 	 * is specified in the capabilities register.
 	 */
-	mmc->max_blk_size = (caps & SDHCI_MAX_BLOCK_MASK) >> SDHCI_MAX_BLOCK_SHIFT;
-	if (mmc->max_blk_size >= 3) {
-		printk(KERN_WARNING "%s: Invalid maximum block size, "
-			"assuming 512 bytes\n", mmc_hostname(mmc));
-		mmc->max_blk_size = 512;
-	} else
-		mmc->max_blk_size = 512 << mmc->max_blk_size;
+	if (host->quirks & SDHCI_QUIRK_MAX_BLK_SZ_4096) {
+		mmc->max_blk_size = 3;
+	} else {
+		mmc->max_blk_size = (caps & SDHCI_MAX_BLOCK_MASK) >>
+				SDHCI_MAX_BLOCK_SHIFT;
+		if (mmc->max_blk_size >= 3) {
+			printk(KERN_WARNING "%s: Invalid maximum block size, "
+				"assuming 512 bytes\n", mmc_hostname(mmc));
+			mmc->max_blk_size = 0;
+		}
+	}
+
+	mmc->max_blk_size = 512 << mmc->max_blk_size;
 
 	/*
 	 * Maximum block count.
diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
index 5c5a950..c8628b4 100644
--- a/drivers/mmc/host/sdhci.h
+++ b/drivers/mmc/host/sdhci.h
@@ -231,6 +231,8 @@ struct sdhci_host {
 #define SDHCI_QUIRK_PIO_NEEDS_DELAY			(1<<20)
 /* Controller losing signal/interrupt enable states after reset */
 #define SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET		(1<<21)
+/* Controller supports nonstandard maximum block length of 4096 bytes */
+#define SDHCI_QUIRK_MAX_BLK_SZ_4096			(1<<22)
 
 	int			irq;		/* Device IRQ */
 	void __iomem *		ioaddr;		/* Mapped address */
-- 
1.5.6.5

  parent reply	other threads:[~2009-02-13 14:47 UTC|newest]

Thread overview: 29+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2009-02-13 14:46 [PATCH RFC 0/13] FSL eSDHC support Anton Vorontsov
2009-02-13 14:47 ` [PATCH 01/13] sdhci: Add quirk for controllers with no end-of-busy IRQ Anton Vorontsov
2009-02-13 14:47 ` [PATCH 02/13] sdhci: Add support for bus-specific IO memory accessors Anton Vorontsov
2009-02-13 14:47 ` [PATCH 03/13] sdhci: Split card-detection IRQs management from sdhci_init() Anton Vorontsov
2009-02-21 15:58   ` Pierre Ossman
2009-02-13 14:47 ` [PATCH 04/13] sdhci: Enable only relevant (DMA/PIO) interrupts during transfers Anton Vorontsov
2009-02-13 14:47 ` [PATCH 05/13] sdhci: Add support for card-detection polling Anton Vorontsov
2009-02-21 15:58   ` Pierre Ossman
2009-03-04 17:49     ` Anton Vorontsov
2009-03-08 14:11       ` Pierre Ossman
2009-03-16 21:05         ` Anton Vorontsov
2009-02-13 14:47 ` [PATCH 06/13] sdhci: Add support for hosts reporting inverted write-protect state Anton Vorontsov
2009-02-13 14:47 ` [PATCH 07/13] sdhci: Add support for hosts with strict 32 bit addressing Anton Vorontsov
2009-02-21 15:58   ` Pierre Ossman
2009-03-04 17:48     ` Anton Vorontsov
2009-03-08 14:17       ` Pierre Ossman
2009-02-13 14:47 ` [PATCH 08/13] sdhci: Add get_{max,timeout}_clock callbacks Anton Vorontsov
2009-02-13 14:47 ` [PATCH 09/13] sdhci: Add set_clock callback and a quirk for nonstandard clocks Anton Vorontsov
2009-02-13 14:47 ` [PATCH 10/13] sdhci: Add quirk for controllers that need small delays for PIO Anton Vorontsov
2009-02-13 14:47 ` [PATCH 11/13] sdhci: Add quirk for controllers that need IRQ re-init after reset Anton Vorontsov
2009-02-13 15:47   ` Laurent Pinchart
2009-02-13 17:30     ` Anton Vorontsov
2009-02-13 14:47 ` Anton Vorontsov [this message]
2009-02-21 15:58   ` [PATCH 12/13] sdhci: Add quirk for controllers with max. block size up to 4096 bytes Pierre Ossman
2009-03-04 17:47     ` Anton Vorontsov
2009-03-08 14:21       ` Pierre Ossman
2009-02-13 14:47 ` [PATCH 13/13] mmc: Add OpenFirmware bindings for SDHCI driver Anton Vorontsov
2009-02-17 16:31 ` [PATCH RFC 0/13] FSL eSDHC support Ben Dooks
  -- strict thread matches above, loose matches on Subject: below --
2009-02-20 17:32 [PATCH " Anton Vorontsov
2009-02-20 17:33 ` [PATCH 12/13] sdhci: Add quirk for controllers with max. block size up to 4096 bytes Anton Vorontsov

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20090213144739.GL23889@oksana.dev.rtsoft.ru \
    --to=avorontsov@ru.mvista.com \
    --cc=DaveLiu@freescale.com \
    --cc=arnd@arndb.de \
    --cc=ben-linux@fluff.org \
    --cc=drzeus-sdhci@drzeus.cx \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linuxppc-dev@ozlabs.org \
    --cc=sdhci-devel@list.drzeus.cx \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).