* Re: Setting some clocks back to DUMMY fixes spdif output on imx6q wandboard rev B1 [not found] <20160828160055.GA2122@begut> @ 2016-08-29 19:28 ` Nicolin Chen 2016-08-29 19:54 ` Xavi Drudis Ferran 0 siblings, 1 reply; 12+ messages in thread From: Nicolin Chen @ 2016-08-29 19:28 UTC (permalink / raw) To: Xavi Drudis Ferran, fabio.estevam Cc: Timur Tabi, Xiubo Li, Shengjiu Wang, alsa-devel, linuxppc-dev Added Fabio as I can't test S/PDIF on my board. On Sun, Aug 28, 2016 at 06:00:55PM +0200, Xavi Drudis Ferran wrote: > I was using linux-libre-3.19 (implies no working sdma) with a > wandboard quad (Freescale imx6q). Spidf output worked fine. > > When I upgraded to linux-libre-4.7 spdif output was supressed without > any error (precisely, with the same errors about sdma that 3.19 gave). > > I saw someone else reporting the same elsewhere with linux-4.4 > https://forum.digikey.com/thread/34240 > (but I don't have a login there) > > This patch fixes it for me and sound works again on spdif. > > But I don't know if it can break (or fix?) something for some other > boards or kernels or cases... I hardly know what I'm doing. > The commits that might have caused the problem for me might be > > commit 833f2cbf7091099baee28136dc68678e974c0ac5 > Author: Shengjiu Wang <shengjiu.wang@freescale.com> > Date: Sat Oct 10 18:15:07 2015 +0800 > > ARM: dts: imx6: change the core clock of spdif > > The correct core clock of spdif is SPDIF_GCLK, which is added to > clock tree. So the dts also need to be updated. > > Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com> > Signed-off-by: Shawn Guo <shawnguo@kernel.org> > > (the commit changed more clocks than SPDIF_GCLK) Yes, it seems that it also tried to correct the clock sources as those were not available when adding the S/PDIF support at the first place. > The issue is fixed for me with this patch but I'm not sure what's the > best way to help fix any issue someone else may have or what other > info or test you might need. Any guidance welcome. > --- linux-4.7-no-spdif-out/arch/arm/boot/dts/imx6qdl.dtsi 2016-07-25 00:19:43.000000000 +0200 > +++ linux-4.7/arch/arm/boot/dts/imx6qdl.dtsi 2016-08-28 17:59:14.276774409 +0200 > @@ -240,9 +240,9 @@ > <&sdma 15 18 0>; > dma-names = "rx", "tx"; > clocks = <&clks IMX6QDL_CLK_SPDIF_GCLK>, <&clks IMX6QDL_CLK_OSC>, > - <&clks IMX6QDL_CLK_SPDIF>, <&clks IMX6QDL_CLK_ASRC>, > - <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_ESAI_EXTAL>, > - <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_MLB>, > + <&clks IMX6QDL_CLK_SPDIF>, <&clks IMX6QDL_CLK_DUMMY>, > + <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>, > + <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>, > <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_SPBA>; > clock-names = "core", "rxtx0", > "rxtx1", "rxtx2", This looks like that you merely revert the SPDIF_GCLK. Would you please do a little debug using "#define DEBUG 1" and check printk from fsl_spdif_probe_txclk() to see the difference between before and after Shengjiu's commit? ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Setting some clocks back to DUMMY fixes spdif output on imx6q wandboard rev B1 2016-08-29 19:28 ` Setting some clocks back to DUMMY fixes spdif output on imx6q wandboard rev B1 Nicolin Chen @ 2016-08-29 19:54 ` Xavi Drudis Ferran 2016-08-30 11:14 ` Xavi Drudis Ferran 0 siblings, 1 reply; 12+ messages in thread From: Xavi Drudis Ferran @ 2016-08-29 19:54 UTC (permalink / raw) To: Nicolin Chen Cc: Xavi Drudis Ferran, fabio.estevam, Timur Tabi, Xiubo Li, Shengjiu Wang, alsa-devel, linuxppc-dev El Mon, Aug 29, 2016 at 12:28:21PM -0700, Nicolin Chen deia: > > Yes, it seems that it also tried to correct the clock sources > as those were not available when adding the S/PDIF support at > the first place. > I wonder if maybe they need to be defined, assigned or somehow listed elsewhere and they are not for wandboard quad (but are for other boards)? > > The issue is fixed for me with this patch but I'm not sure what's the > > best way to help fix any issue someone else may have or what other > > info or test you might need. Any guidance welcome. > > > --- linux-4.7-no-spdif-out/arch/arm/boot/dts/imx6qdl.dtsi 2016-07-25 00:19:43.000000000 +0200 > > +++ linux-4.7/arch/arm/boot/dts/imx6qdl.dtsi 2016-08-28 17:59:14.276774409 +0200 > > @@ -240,9 +240,9 @@ > > <&sdma 15 18 0>; > > dma-names = "rx", "tx"; > > clocks = <&clks IMX6QDL_CLK_SPDIF_GCLK>, <&clks IMX6QDL_CLK_OSC>, > > - <&clks IMX6QDL_CLK_SPDIF>, <&clks IMX6QDL_CLK_ASRC>, > > - <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_ESAI_EXTAL>, > > - <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_MLB>, > > + <&clks IMX6QDL_CLK_SPDIF>, <&clks IMX6QDL_CLK_DUMMY>, > > + <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>, > > + <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>, > > <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_SPBA>; > > clock-names = "core", "rxtx0", > > "rxtx1", "rxtx2", > > This looks like that you merely revert the SPDIF_GCLK. I revert only some clocks, yes. I left SPDIF_GCLK and CLK_SBPA intact. So it is a partial revert of the commit. > Would you > please do a little debug using "#define DEBUG 1" and check printk > from fsl_spdif_probe_txclk() to see the difference between before > and after Shengjiu's commit? Yes, but I'm compiling the kernel in the wandboard, so it'll take me some time. Thank you. ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Setting some clocks back to DUMMY fixes spdif output on imx6q wandboard rev B1 2016-08-29 19:54 ` Xavi Drudis Ferran @ 2016-08-30 11:14 ` Xavi Drudis Ferran 2016-08-31 4:21 ` Nicolin Chen 0 siblings, 1 reply; 12+ messages in thread From: Xavi Drudis Ferran @ 2016-08-30 11:14 UTC (permalink / raw) To: Nicolin Chen Cc: Xavi Drudis Ferran, fabio.estevam, Timur Tabi, Xiubo Li, Shengjiu Wang, alsa-devel, linuxppc-dev El Mon, Aug 29, 2016 at 09:54:28PM +0200, Xavi Drudis Ferran deia: > El Mon, Aug 29, 2016 at 12:28:21PM -0700, Nicolin Chen deia: > > Would you > > please do a little debug using "#define DEBUG 1" and check printk > > from fsl_spdif_probe_txclk() to see the difference between before > > and after Shengjiu's commit? > > Yes, but I'm compiling the kernel in the wandboard, so it'll take me some time. > Now. Sorry for the delay. I did a mistake and had to do it twice. I added a couple of sanity check messages: "enter fsl_spdif_probe" "enter fsl_spdif_probe_txclk" linux-libre-4.7 without my patch, i.e. clocks defined like this : arch/arm/boot/dts/imx6qdl.dtsi: aips-bus@02000000 { /* AIPS1 */ [...] spba-bus@02000000 { [...] spdif: spdif@02004000 { clocks = <&clks IMX6QDL_CLK_SPDIF_GCLK>, <&clks IMX6QDL_CLK_OSC>, <&clks IMX6QDL_CLK_SPDIF>, <&clks IMX6QDL_CLK_ASRC>, <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_ESAI_EXTAL>, <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_MLB>, <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_SPBA>; clock-names = "core", "rxtx0", "rxtx1", "rxtx2", "rxtx3", "rxtx4", "rxtx5", "rxtx6", "rxtx7", "spba"; [...] The messages at boot: [ 8.803603] 20ec000.sdma: Missing Free firmware (non-Free firmware loading is disabled) [ 8.813737] imx-sdma 20ec000.sdma: failed to get firmware from device tree [ 8.870764] imx-sdma 20ec000.sdma: Direct firmware load for /*(DEBLOBBED)*/ failed with error -2 [...] [ 9.083301] fsl-asrc 2034000.asrc: driver registered [ 9.087050] sgtl5000 1-000a: sgtl5000 revision 0x11 [ 9.107141] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe [ 9.144839] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 9.225228] fsl-spdif-dai 2004000.spdif: use rxtx5 as tx clock source for 32000Hz sample rate [ 9.234058] fsl-spdif-dai 2004000.spdif: use txclk df 16 for 32000Hz sample rate [ 9.235565] imx-spdif sound-spdif: ASoC: CPU DAI (null) not registered [ 9.236007] imx-spdif sound-spdif: snd_soc_register_card failed: -517 [...] [ 9.262713] fsl-spdif-dai 2004000.spdif: use sysclk df 2 for 32000Hz sample rate [ 9.269349] fsl-spdif-dai 2004000.spdif: the best rate for 32000Hz sample rate is 32226Hz [ 9.276431] fsl-asoc-card sound: ASoC: CPU DAI (null) not registered [ 9.276438] fsl-asoc-card sound: snd_soc_register_card failed (-517) [ 9.289559] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 9.306991] imx-sgtl5000 sound: ASoC: CPU DAI (null) not registered [ 9.346253] imx-sgtl5000 sound: snd_soc_register_card failed (-517) [ 9.376398] fsl-spdif-dai 2004000.spdif: use rxtx6 as tx clock source for 44100Hz sample rate [ 9.376404] fsl-spdif-dai 2004000.spdif: use txclk df 94 for 44100Hz sample rate [ 9.376409] fsl-spdif-dai 2004000.spdif: the best rate for 44100Hz sample rate is 43882Hz [ 9.376415] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 9.403159] fsl-spdif-dai 2004000.spdif: use rxtx6 as tx clock source for 48000Hz sample rate [ 9.403165] fsl-spdif-dai 2004000.spdif: use txclk df 86 for 48000Hz sample rate [ 9.403170] fsl-spdif-dai 2004000.spdif: the best rate for 48000Hz sample rate is 47965Hz [ 9.403174] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 9.424007] fsl-spdif-dai 2004000.spdif: use rxtx6 as tx clock source for 96000Hz sample rate [ 9.424013] fsl-spdif-dai 2004000.spdif: use txclk df 43 for 96000Hz sample rate [ 9.424021] fsl-spdif-dai 2004000.spdif: the best rate for 96000Hz sample rate is 95930Hz [ 9.424025] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 9.450424] fsl-spdif-dai 2004000.spdif: use rxtx6 as tx clock source for 192000Hz sample rate [ 9.481561] fsl-spdif-dai 2004000.spdif: use txclk df 21 for 192000Hz sample rate [ 9.488400] fsl-spdif-dai 2004000.spdif: the best rate for 192000Hz sample rate is 196428Hz [ 9.536785] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW [ 9.582106] imx-spdif sound-spdif: snd-soc-dummy-dai <-> 2004000.spdif mapping ok [ 9.612159] fsl-asoc-card sound: ASoC: CPU DAI (null) not registered [ 9.621942] fsl-asoc-card sound: snd_soc_register_card failed (-517) [ 9.638227] imx-sgtl5000 sound: ASoC: CPU DAI (null) not registered [ 9.647247] imx-sgtl5000 sound: snd_soc_register_card failed (-517) [ 9.682092] sgtl5000 1-000a: Using internal LDO instead of VDDD [ 9.776989] fsl-asoc-card sound: sgtl5000 <-> 2028000.ssi mapping ok [...] [ 70.407805] fsl-spdif-dai 2004000.spdif: expected clock rate = 265305600 [ 70.407829] fsl-spdif-dai 2004000.spdif: actual clock rate = 264000000 [ 70.407857] fsl-spdif-dai 2004000.spdif: set sample rate to 43882Hz for 44100Hz playback [ 70.407867] fsl-spdif-dai 2004000.spdif: STCSCH: 0x304000 [ 70.407875] fsl-spdif-dai 2004000.spdif: STCSCL: 0x000000 [ 70.469948] fsl-spdif-dai 2004000.spdif: expected clock rate = 265305600 [ 70.469965] fsl-spdif-dai 2004000.spdif: actual clock rate = 264000000 [ 70.469977] fsl-spdif-dai 2004000.spdif: set sample rate to 43882Hz for 44100Hz playback [ 70.469999] fsl-spdif-dai 2004000.spdif: STCSCH: 0x304000 [ 70.470014] fsl-spdif-dai 2004000.spdif: STCSCL: 0x000000 [...] Then when I try to play sound through spdif: [ 140.176536] fsl-spdif-dai 2004000.spdif: expected clock rate = 265305600 [ 140.176555] fsl-spdif-dai 2004000.spdif: actual clock rate = 264000000 [ 140.176566] fsl-spdif-dai 2004000.spdif: set sample rate to 43882Hz for 44100Hz playback [ 140.176579] fsl-spdif-dai 2004000.spdif: STCSCH: 0x304000 [ 140.176587] fsl-spdif-dai 2004000.spdif: STCSCL: 0x000000 linux-libre-4.7 with my patch, i.e. clocks defined like this : arch/arm/boot/dts/imx6qdl.dtsi: aips-bus@02000000 { /* AIPS1 */ [...] spba-bus@02000000 { [...] spdif: spdif@02004000 { clocks = <&clks IMX6QDL_CLK_SPDIF_GCLK>, <&clks IMX6QDL_CLK_OSC>, <&clks IMX6QDL_CLK_SPDIF>, <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_SPBA>; clock-names = "core", "rxtx0", "rxtx1", "rxtx2", "rxtx3", "rxtx4", "rxtx5", "rxtx6", "rxtx7", "spba"; [...] The messages at boot: [...] [ 6.655532] imx-spdif sound-spdif: ASoC: CPU DAI (null) not registered [ 6.655545] imx-spdif sound-spdif: snd_soc_register_card failed: -517 [ 6.656895] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe [ 6.657567] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 6.660895] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 32000Hz sample rate [ 6.660902] fsl-spdif-dai 2004000.spdif: use txclk df 4 for 32000Hz sample rate [ 6.660907] fsl-spdif-dai 2004000.spdif: the best rate for 32000Hz sample rate is 31719Hz [ 6.660911] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 6.662922] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 44100Hz sample rate [ 6.662927] fsl-spdif-dai 2004000.spdif: use txclk df 9 for 44100Hz sample rate [ 6.662932] fsl-spdif-dai 2004000.spdif: the best rate for 44100Hz sample rate is 43859Hz [ 6.662936] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 6.663205] fsl-asoc-card sound: ASoC: CPU DAI (null) not registered [ 6.663213] fsl-asoc-card sound: snd_soc_register_card failed (-517) [ 6.676779] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 48000Hz sample rate [ 6.676785] fsl-spdif-dai 2004000.spdif: use txclk df 5 for 48000Hz sample rate [ 6.676790] fsl-spdif-dai 2004000.spdif: the best rate for 48000Hz sample rate is 47368Hz [ 6.676795] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 6.687008] imx-sgtl5000 sound: ASoC: CPU DAI (null) not registered [ 6.687016] imx-sgtl5000 sound: snd_soc_register_card failed (-517) [ 6.704876] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 96000Hz sample rate [ 6.704882] fsl-spdif-dai 2004000.spdif: use txclk df 3 for 96000Hz sample rate [ 6.704888] fsl-spdif-dai 2004000.spdif: the best rate for 96000Hz sample rate is 94736Hz [ 6.704892] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 6.723554] fsl-spdif-dai 2004000.spdif: use rxtx0 as tx clock source for 192000Hz sample rate [ 6.723561] fsl-spdif-dai 2004000.spdif: use txclk df 2 for 192000Hz sample rate [ 6.723567] fsl-spdif-dai 2004000.spdif: the best rate for 192000Hz sample rate is 187500Hz [ 6.723679] fsl-spdif-dai 2004000.spdif: imx_pcm_dma_init failed: -517 [ 7.626351] fsl-asrc 2034000.asrc: driver registered [ 7.642378] imx-spdif sound-spdif: ASoC: CPU DAI (null) not registered [ 7.650279] imx-spdif sound-spdif: snd_soc_register_card failed: -517 [ 7.667765] fsl-asoc-card sound: ASoC: CPU DAI (null) not registered [ 7.676924] fsl-asoc-card sound: snd_soc_register_card failed (-517) [ 7.696535] imx-sgtl5000 sound: ASoC: CPU DAI (null) not registered [ 7.704977] imx-sgtl5000 sound: snd_soc_register_card failed (-517) [ 7.718722] sgtl5000 1-000a: sgtl5000 revision 0x11 [...] [ 7.725855] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW [ 7.728561] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe [ 7.738178] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.740172] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 32000Hz sample rate [ 7.740177] fsl-spdif-dai 2004000.spdif: use txclk df 4 for 32000Hz sample rate [ 7.740183] fsl-spdif-dai 2004000.spdif: the best rate for 32000Hz sample rate is 31719Hz [ 7.740187] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.760659] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 44100Hz sample rate [ 7.760665] fsl-spdif-dai 2004000.spdif: use txclk df 9 for 44100Hz sample rate [ 7.760672] fsl-spdif-dai 2004000.spdif: the best rate for 44100Hz sample rate is 43859Hz [ 7.760676] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.765495] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 48000Hz sample rate [ 7.765501] fsl-spdif-dai 2004000.spdif: use txclk df 5 for 48000Hz sample rate [ 7.765506] fsl-spdif-dai 2004000.spdif: the best rate for 48000Hz sample rate is 47368Hz [ 7.765510] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.774373] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 96000Hz sample rate [ 7.774378] fsl-spdif-dai 2004000.spdif: use txclk df 3 for 96000Hz sample rate [ 7.774384] fsl-spdif-dai 2004000.spdif: the best rate for 96000Hz sample rate is 94736Hz [ 7.774388] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.778530] fsl-spdif-dai 2004000.spdif: use rxtx0 as tx clock source for 192000Hz sample rate [ 7.778536] fsl-spdif-dai 2004000.spdif: use txclk df 2 for 192000Hz sample rate [ 7.778541] fsl-spdif-dai 2004000.spdif: the best rate for 192000Hz sample rate is 187500Hz [ 7.783897] fsl-spdif-dai 2004000.spdif: imx_pcm_dma_init failed: -517 [ 7.828163] imx-spdif sound-spdif: ASoC: CPU DAI (null) not registered [ 7.828174] imx-spdif sound-spdif: snd_soc_register_card failed: -517 [ 7.828703] fsl-asoc-card sound: ASoC: CPU DAI (null) not registered [ 7.828712] fsl-asoc-card sound: snd_soc_register_card failed (-517) [ 7.828825] imx-sgtl5000 sound: ASoC: CPU DAI (null) not registered [ 7.828832] imx-sgtl5000 sound: snd_soc_register_card failed (-517) [ 7.829908] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW [ 7.834312] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe [ 7.837686] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.842472] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 32000Hz sample rate [ 7.842478] fsl-spdif-dai 2004000.spdif: use txclk df 4 for 32000Hz sample rate [ 7.842485] fsl-spdif-dai 2004000.spdif: the best rate for 32000Hz sample rate is 31719Hz [ 7.842490] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.844695] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 44100Hz sample rate [ 7.844700] fsl-spdif-dai 2004000.spdif: use txclk df 9 for 44100Hz sample rate [ 7.844705] fsl-spdif-dai 2004000.spdif: the best rate for 44100Hz sample rate is 43859Hz [ 7.844708] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.848458] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 48000Hz sample rate [ 7.848464] fsl-spdif-dai 2004000.spdif: use txclk df 5 for 48000Hz sample rate [ 7.848470] fsl-spdif-dai 2004000.spdif: the best rate for 48000Hz sample rate is 47368Hz [ 7.848474] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.858907] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 96000Hz sample rate [ 7.858912] fsl-spdif-dai 2004000.spdif: use txclk df 3 for 96000Hz sample rate [ 7.858917] fsl-spdif-dai 2004000.spdif: the best rate for 96000Hz sample rate is 94736Hz [ 7.858921] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.868189] fsl-spdif-dai 2004000.spdif: use rxtx0 as tx clock source for 192000Hz sample rate [ 7.868195] fsl-spdif-dai 2004000.spdif: use txclk df 2 for 192000Hz sample rate [ 7.868200] fsl-spdif-dai 2004000.spdif: the best rate for 192000Hz sample rate is 187500Hz [ 7.868555] fsl-spdif-dai 2004000.spdif: imx_pcm_dma_init failed: -517 [ 8.094960] imx-spdif sound-spdif: ASoC: CPU DAI (null) not registered [ 8.094994] imx-spdif sound-spdif: snd_soc_register_card failed: -517 [ 8.095669] fsl-asoc-card sound: ASoC: CPU DAI (null) not registered [ 8.095808] fsl-asoc-card sound: snd_soc_register_card failed (-517) [ 8.098338] imx-sgtl5000 sound: ASoC: CPU DAI (null) not registered [ 8.098347] imx-sgtl5000 sound: snd_soc_register_card failed (-517) [ 8.099067] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW [ 8.109691] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe [ 8.113038] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 8.117534] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 32000Hz sample rate [ 8.117539] fsl-spdif-dai 2004000.spdif: use txclk df 4 for 32000Hz sample rate [ 8.117544] fsl-spdif-dai 2004000.spdif: the best rate for 32000Hz sample rate is 31719Hz [ 8.117548] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 8.120341] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 44100Hz sample rate [ 8.120347] fsl-spdif-dai 2004000.spdif: use txclk df 9 for 44100Hz sample rate [ 8.120352] fsl-spdif-dai 2004000.spdif: the best rate for 44100Hz sample rate is 43859Hz [ 8.120356] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 8.134938] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 48000Hz sample rate [ 8.134944] fsl-spdif-dai 2004000.spdif: use txclk df 5 for 48000Hz sample rate [ 8.134949] fsl-spdif-dai 2004000.spdif: the best rate for 48000Hz sample rate is 47368Hz [ 8.134953] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 8.139127] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 96000Hz sample rate [ 8.139133] fsl-spdif-dai 2004000.spdif: use txclk df 3 for 96000Hz sample rate [ 8.139139] fsl-spdif-dai 2004000.spdif: the best rate for 96000Hz sample rate is 94736Hz [ 8.139143] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 8.147727] fsl-spdif-dai 2004000.spdif: use rxtx0 as tx clock source for 192000Hz sample rate [ 8.147734] fsl-spdif-dai 2004000.spdif: use txclk df 2 for 192000Hz sample rate [ 8.147740] fsl-spdif-dai 2004000.spdif: the best rate for 192000Hz sample rate is 187500Hz [ 8.147822] fsl-spdif-dai 2004000.spdif: imx_pcm_dma_init failed: -517 [...] [ 8.831797] 20ec000.sdma: Missing Free firmware (non-Free firmware loading is disabled) [ 8.880684] imx-sdma 20ec000.sdma: failed to get firmware from device tree [ 8.910258] imx-sdma 20ec000.sdma: Direct firmware load for /*(DEBLOBBED)*/ failed with error -2 [ 9.073968] imx-spdif sound-spdif: ASoC: CPU DAI (null) not registered [ 9.081645] imx-spdif sound-spdif: snd_soc_register_card failed: -517 [ 9.095074] fsl-asoc-card sound: ASoC: CPU DAI (null) not registered [ 9.110834] fsl-asoc-card sound: snd_soc_register_card failed (-517) [ 9.121216] imx-sgtl5000 sound: ASoC: CPU DAI (null) not registered [ 9.130267] imx-sgtl5000 sound: snd_soc_register_card failed (-517) [ 9.153016] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW [ 9.165177] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe [ 9.195832] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 9.211198] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 32000Hz sample rate [ 9.217917] fsl-spdif-dai 2004000.spdif: use txclk df 4 for 32000Hz sample rate [ 9.224900] fsl-spdif-dai 2004000.spdif: the best rate for 32000Hz sample rate is 31719Hz [ 9.231164] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 9.241790] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 44100Hz sample rate [ 9.248073] fsl-spdif-dai 2004000.spdif: use txclk df 9 for 44100Hz sample rate [ 9.254457] fsl-spdif-dai 2004000.spdif: the best rate for 44100Hz sample rate is 43859Hz [ 9.260822] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 9.279536] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 48000Hz sample rate [ 9.285950] fsl-spdif-dai 2004000.spdif: use txclk df 5 for 48000Hz sample rate [ 9.292236] fsl-spdif-dai 2004000.spdif: the best rate for 48000Hz sample rate is 47368Hz [ 9.298648] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 9.313550] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 96000Hz sample rate [...] [ 9.328117] fsl-spdif-dai 2004000.spdif: use txclk df 3 for 96000Hz sample rate [ 9.334526] fsl-spdif-dai 2004000.spdif: the best rate for 96000Hz sample rate is 94736Hz [ 9.340888] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 9.351639] fsl-spdif-dai 2004000.spdif: use rxtx0 as tx clock source for 192000Hz sample rate [ 9.358052] fsl-spdif-dai 2004000.spdif: use txclk df 2 for 192000Hz sample rate [ 9.364471] fsl-spdif-dai 2004000.spdif: the best rate for 192000Hz sample rate is 187500Hz [ 9.417677] imx-spdif sound-spdif: snd-soc-dummy-dai <-> 2004000.spdif mapping ok [ 9.461316] sgtl5000 1-000a: Using internal LDO instead of VDDD [ 9.592189] fsl-asoc-card sound: sgtl5000 <-> 2028000.ssi mapping ok [...] [ 69.198853] fsl-spdif-dai 2004000.spdif: expected clock rate = 25401600 [ 69.198874] fsl-spdif-dai 2004000.spdif: actual clock rate = 25263158 [ 69.198892] fsl-spdif-dai 2004000.spdif: set sample rate to 43859Hz for 44100Hz playback [ 69.198902] fsl-spdif-dai 2004000.spdif: STCSCH: 0x304000 [ 69.198910] fsl-spdif-dai 2004000.spdif: STCSCL: 0x000000 [ 69.349763] fsl-spdif-dai 2004000.spdif: expected clock rate = 25401600 [ 69.349776] fsl-spdif-dai 2004000.spdif: actual clock rate = 25263158 [ 69.349793] fsl-spdif-dai 2004000.spdif: set sample rate to 43859Hz for 44100Hz playback [ 69.349812] fsl-spdif-dai 2004000.spdif: STCSCH: 0x304000 [ 69.349820] fsl-spdif-dai 2004000.spdif: STCSCL: 0x000000 [...] Then when I try (successfully) to play sound through spdif: [ 113.186850] fsl-spdif-dai 2004000.spdif: expected clock rate = 25401600 [ 113.186863] fsl-spdif-dai 2004000.spdif: actual clock rate = 25263158 [ 113.186872] fsl-spdif-dai 2004000.spdif: set sample rate to 43859Hz for 44100Hz playback [ 113.186882] fsl-spdif-dai 2004000.spdif: STCSCH: 0x304000 [ 113.186889] fsl-spdif-dai 2004000.spdif: STCSCL: 0x000000 Does it mean that a 43859Hz clock is close enough to theoretical 44100Hz but 43882Hz is not ? The clock that doesn't work seems closer to the desired value. I don't understand. Maybe there's something wrong with rxtx6 (IMX6QDL_CLK_MLB). This clock does not seem to be used elsewhere (I mean in files, it's used in any board that includes imx6qdl.dtsi) include/dt-bindings/clock/imx6qdl-clock.h: #define IMX6QDL_CLK_MLB 139 Might it have to do with the fact I'm using (still trying in fact) to use etnaviv ? drivers/clk/imx/clk-imx6q.c: if (clk_on_imx6dl()) /* * The multiplexer and divider of the imx6q clock gpu2d get * redefined/reused as mlb_sys_sel and mlb_sys_clk_podf on imx6dl. */ clk[IMX6QDL_CLK_MLB] = imx_clk_gate2("mlb", "gpu2d_core_podf", base + 0x74, 18); else clk[IMX6QDL_CLK_MLB] = imx_clk_gate2("mlb", "axi", base + 0x74, 18); But I'm on a imx6q not imx6dl . It seems I've found a similar case, just more ancient. I've tried the patch in the last message there instead of the one I sent, and it works for me (gives me sound on the spdif output) but I still don't understand. https://community.nxp.com/thread/387131 The patch is --- linux-4.7-no-spdif-out/arch/arm/boot/dts/imx6qdl.dtsi 2016-07-25 00:19:43.000000000 +0200 +++ linux-4.7/arch/arm/boot/dts/imx6qdl.dtsi 2016-08-30 12:51:37.369431791 +0200 @@ -242,7 +242,7 @@ clocks = <&clks IMX6QDL_CLK_SPDIF_GCLK>, <&clks IMX6QDL_CLK_OSC>, <&clks IMX6QDL_CLK_SPDIF>, <&clks IMX6QDL_CLK_ASRC>, <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_ESAI_EXTAL>, - <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_MLB>, + <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_SPBA>; clock-names = "core", "rxtx0", "rxtx1", "rxtx2", And the dmesg is: [...] [ 6.757672] fsl-asoc-card sound: ASoC: CPU DAI (null) not registered [ 6.757680] fsl-asoc-card sound: snd_soc_register_card failed (-517) [ 6.767863] imx-sgtl5000 sound: ASoC: CPU DAI (null) not registered [ 6.767874] imx-sgtl5000 sound: snd_soc_register_card failed (-517) [ 6.771927] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW [ 6.782230] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe [ 6.795682] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 6.851089] fsl-spdif-dai 2004000.spdif: use rxtx5 as tx clock source for 32000Hz sample rate [ 6.857631] fsl-spdif-dai 2004000.spdif: use txclk df 16 for 32000Hz sample rate [ 6.864477] fsl-spdif-dai 2004000.spdif: use sysclk df 2 for 32000Hz sample rate [ 6.864484] fsl-spdif-dai 2004000.spdif: the best rate for 32000Hz sample rate is 32226Hz [ 6.864489] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 6.909089] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 44100Hz sample rate [ 6.909096] fsl-spdif-dai 2004000.spdif: use txclk df 9 for 44100Hz sample rate [ 6.909101] fsl-spdif-dai 2004000.spdif: the best rate for 44100Hz sample rate is 43859Hz [ 6.909105] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 6.981874] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 48000Hz sample rate [ 6.992935] fsl-spdif-dai 2004000.spdif: use txclk df 5 for 48000Hz sample rate [ 6.992943] fsl-spdif-dai 2004000.spdif: the best rate for 48000Hz sample rate is 47368Hz [ 6.992948] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 6.993678] fsl-asoc-card sound: ASoC: CPU DAI (null) not registered [ 6.993688] fsl-asoc-card sound: snd_soc_register_card failed (-517) [ 6.993809] imx-sgtl5000 sound: ASoC: CPU DAI (null) not registered [ 6.993816] imx-sgtl5000 sound: snd_soc_register_card failed (-517) [ 6.994121] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW [ 7.024546] 20ec000.sdma: Missing Free firmware (non-Free firmware loading is disabled) [ 7.024577] imx-sdma 20ec000.sdma: failed to get firmware from device tree [ 7.025416] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 96000Hz sample rate [ 7.025422] fsl-spdif-dai 2004000.spdif: use txclk df 3 for 96000Hz sample rate [ 7.025426] fsl-spdif-dai 2004000.spdif: the best rate for 96000Hz sample rate is 94736Hz [ 7.025430] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.040198] imx-sdma 20ec000.sdma: Direct firmware load for /*(DEBLOBBED)*/ failed with error -2 [ 7.052490] fsl-spdif-dai 2004000.spdif: use rxtx0 as tx clock source for 192000Hz sample rate [ 7.052497] fsl-spdif-dai 2004000.spdif: use txclk df 2 for 192000Hz sample rate [ 7.052503] fsl-spdif-dai 2004000.spdif: the best rate for 192000Hz sample rate is 187500Hz [ 7.052601] fsl-spdif-dai 2004000.spdif: imx_pcm_dma_init failed: -517 [ 7.053550] fsl-asoc-card sound: ASoC: CPU DAI (null) not registered [ 7.053560] fsl-asoc-card sound: snd_soc_register_card failed (-517) [ 7.054022] imx-sgtl5000 sound: ASoC: CPU DAI (null) not registered [ 7.054295] imx-sgtl5000 sound: snd_soc_register_card failed (-517) [ 7.056803] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW [ 7.060206] fsl-asrc 2034000.asrc: driver registered [ 7.063842] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe [ 7.064485] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.096570] fsl-spdif-dai 2004000.spdif: use rxtx5 as tx clock source for 32000Hz sample rate [ 7.096579] fsl-spdif-dai 2004000.spdif: use txclk df 16 for 32000Hz sample rate [ 7.096584] fsl-spdif-dai 2004000.spdif: use sysclk df 2 for 32000Hz sample rate [ 7.096589] fsl-spdif-dai 2004000.spdif: the best rate for 32000Hz sample rate is 32226Hz [ 7.096593] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.123283] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 44100Hz sample rate [ 7.123289] fsl-spdif-dai 2004000.spdif: use txclk df 9 for 44100Hz sample rate [ 7.123295] fsl-spdif-dai 2004000.spdif: the best rate for 44100Hz sample rate is 43859Hz [ 7.123299] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.144167] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 48000Hz sample rate [ 7.144173] fsl-spdif-dai 2004000.spdif: use txclk df 5 for 48000Hz sample rate [ 7.144180] fsl-spdif-dai 2004000.spdif: the best rate for 48000Hz sample rate is 47368Hz [ 7.144185] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.169620] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 96000Hz sample rate [ 7.169626] fsl-spdif-dai 2004000.spdif: use txclk df 3 for 96000Hz sample rate [ 7.169634] fsl-spdif-dai 2004000.spdif: the best rate for 96000Hz sample rate is 94736Hz [ 7.169637] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.190745] fsl-spdif-dai 2004000.spdif: use rxtx0 as tx clock source for 192000Hz sample rate [ 7.190753] fsl-spdif-dai 2004000.spdif: use txclk df 2 for 192000Hz sample rate [ 7.190758] fsl-spdif-dai 2004000.spdif: the best rate for 192000Hz sample rate is 187500Hz [ 7.190883] fsl-spdif-dai 2004000.spdif: imx_pcm_dma_init failed: -517 [ 7.191660] fsl-asoc-card sound: ASoC: CPU DAI (null) not registered [ 7.191671] fsl-asoc-card sound: snd_soc_register_card failed (-517) [ 7.191777] imx-sgtl5000 sound: ASoC: CPU DAI (null) not registered [ 7.191784] imx-sgtl5000 sound: snd_soc_register_card failed (-517) [ 7.192106] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW [ 7.220888] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe [ 7.221677] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.246497] fsl-spdif-dai 2004000.spdif: use rxtx5 as tx clock source for 32000Hz sample rate [ 7.246504] fsl-spdif-dai 2004000.spdif: use txclk df 16 for 32000Hz sample rate [ 7.246510] fsl-spdif-dai 2004000.spdif: use sysclk df 2 for 32000Hz sample rate [ 7.246515] fsl-spdif-dai 2004000.spdif: the best rate for 32000Hz sample rate is 32226Hz [ 7.246520] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.266974] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 44100Hz sample rate [ 7.266980] fsl-spdif-dai 2004000.spdif: use txclk df 9 for 44100Hz sample rate [ 7.266985] fsl-spdif-dai 2004000.spdif: the best rate for 44100Hz sample rate is 43859Hz [ 7.266989] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.288040] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 48000Hz sample rate [ 7.288046] fsl-spdif-dai 2004000.spdif: use txclk df 5 for 48000Hz sample rate [ 7.288051] fsl-spdif-dai 2004000.spdif: the best rate for 48000Hz sample rate is 47368Hz [ 7.288055] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.320893] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 96000Hz sample rate [ 7.320901] fsl-spdif-dai 2004000.spdif: use txclk df 3 for 96000Hz sample rate [ 7.320909] fsl-spdif-dai 2004000.spdif: the best rate for 96000Hz sample rate is 94736Hz [ 7.320915] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.342352] fsl-spdif-dai 2004000.spdif: use rxtx0 as tx clock source for 192000Hz sample rate [ 7.342363] fsl-spdif-dai 2004000.spdif: use txclk df 2 for 192000Hz sample rate [ 7.342370] fsl-spdif-dai 2004000.spdif: the best rate for 192000Hz sample rate is 187500Hz [ 7.369879] fsl-asoc-card sound: ASoC: CPU DAI (null) not registered [ 7.369889] fsl-asoc-card sound: snd_soc_register_card failed (-517) [ 7.370024] imx-sgtl5000 sound: ASoC: CPU DAI (null) not registered [ 7.370033] imx-sgtl5000 sound: snd_soc_register_card failed (-517) [ 7.391119] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW [ 7.422777] fsl-asoc-card sound: ASoC: CODEC DAI sgtl5000 not registered [ 7.422789] fsl-asoc-card sound: snd_soc_register_card failed (-517) [ 7.423120] imx-sgtl5000 sound: ASoC: CODEC DAI sgtl5000 not registered [ 7.423133] imx-sgtl5000 sound: snd_soc_register_card failed (-517) [ 7.454462] sgtl5000 1-000a: sgtl5000 revision 0x11 [...] [ 7.658346] sgtl5000 1-000a: Using internal LDO instead of VDDD [ 7.766216] fsl-asoc-card sound: sgtl5000 <-> 2028000.ssi mapping ok [...] [ 8.496784] imx-spdif sound-spdif: snd-soc-dummy-dai <-> 2004000.spdif mapping ok [...] [ 110.494306] fsl-spdif-dai 2004000.spdif: expected clock rate = 25401600 [ 110.494321] fsl-spdif-dai 2004000.spdif: actual clock rate = 25263158 [ 110.494343] fsl-spdif-dai 2004000.spdif: set sample rate to 43859Hz for 44100Hz playback [ 110.494352] fsl-spdif-dai 2004000.spdif: STCSCH: 0x304000 [ 110.494359] fsl-spdif-dai 2004000.spdif: STCSCL: 0x000000 [ 110.549945] fsl-spdif-dai 2004000.spdif: expected clock rate = 25401600 [ 110.549959] fsl-spdif-dai 2004000.spdif: actual clock rate = 25263158 [ 110.549973] fsl-spdif-dai 2004000.spdif: set sample rate to 43859Hz for 44100Hz playback [ 110.549988] fsl-spdif-dai 2004000.spdif: STCSCH: 0x304000 [ 110.549996] fsl-spdif-dai 2004000.spdif: STCSCL: 0x000000 Then, when I play music: [ 178.269300] fsl-spdif-dai 2004000.spdif: expected clock rate = 25401600 [ 178.269311] fsl-spdif-dai 2004000.spdif: actual clock rate = 25263158 [ 178.269321] fsl-spdif-dai 2004000.spdif: set sample rate to 43859Hz for 44100Hz playback [ 178.269332] fsl-spdif-dai 2004000.spdif: STCSCH: 0x304000 [ 178.269339] fsl-spdif-dai 2004000.spdif: STCSCL: 0x000000 AFAICS it just uses rxtx5 (IMX6QDL_CLK_IPG) for 32KHz and gets a little closer to that. But I haven't tried to play at 32KHz Is there anything else I can try ? Thanks. ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Setting some clocks back to DUMMY fixes spdif output on imx6q wandboard rev B1 2016-08-30 11:14 ` Xavi Drudis Ferran @ 2016-08-31 4:21 ` Nicolin Chen 2016-08-31 9:10 ` Xavi Drudis Ferran 0 siblings, 1 reply; 12+ messages in thread From: Nicolin Chen @ 2016-08-31 4:21 UTC (permalink / raw) To: Xavi Drudis Ferran Cc: fabio.estevam, Timur Tabi, Xiubo Li, Shengjiu Wang, alsa-devel, linuxppc-dev On Tue, Aug 30, 2016 at 01:14:14PM +0200, Xavi Drudis Ferran wrote: > linux-libre-4.7 without my patch, i.e. clocks defined like this : > arch/arm/boot/dts/imx6qdl.dtsi: > aips-bus@02000000 { /* AIPS1 */ > [...] > spba-bus@02000000 { > [...] > spdif: spdif@02004000 { > clocks = <&clks IMX6QDL_CLK_SPDIF_GCLK>, <&clks IMX6QDL_CLK_OSC>, > <&clks IMX6QDL_CLK_SPDIF>, <&clks IMX6QDL_CLK_ASRC>, > <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_ESAI_EXTAL>, > <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_MLB>, > <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_SPBA>; > clock-names = "core", "rxtx0", > "rxtx1", "rxtx2", > "rxtx3", "rxtx4", > "rxtx5", "rxtx6", > "rxtx7", "spba"; > [...] > [ 9.376398] fsl-spdif-dai 2004000.spdif: use rxtx6 as tx clock source for 44100Hz sample rate > [ 9.376404] fsl-spdif-dai 2004000.spdif: use txclk df 94 for 44100Hz sample rate > [ 9.376409] fsl-spdif-dai 2004000.spdif: the best rate for 44100Hz sample rate is 43882Hz Without your patch, it chose rxtx6 (MLB) as the source for 44.1KHz. > linux-libre-4.7 with my patch, i.e. clocks defined like this : > arch/arm/boot/dts/imx6qdl.dtsi: > aips-bus@02000000 { /* AIPS1 */ > [...] > spba-bus@02000000 { > [...] > spdif: spdif@02004000 { > clocks = <&clks IMX6QDL_CLK_SPDIF_GCLK>, <&clks IMX6QDL_CLK_OSC>, > <&clks IMX6QDL_CLK_SPDIF>, <&clks IMX6QDL_CLK_DUMMY>, > <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>, > <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>, > <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_SPBA>; > clock-names = "core", "rxtx0", > "rxtx1", "rxtx2", > "rxtx3", "rxtx4", > "rxtx5", "rxtx6", > "rxtx7", "spba"; > [...] > [ 6.662922] fsl-spdif-dai 2004000.spdif: use rxtx1 as tx clock source for 44100Hz sample rate > [ 6.662927] fsl-spdif-dai 2004000.spdif: use txclk df 9 for 44100Hz sample rate > [ 6.662932] fsl-spdif-dai 2004000.spdif: the best rate for 44100Hz sample rate is 43859Hz With your patch, it selects rxtx1 (the dedicated SPDIF baud clock). > Does it mean that a 43859Hz clock is close enough to theoretical 44100Hz > but 43882Hz is not ? No, the problem is not at the rate but the source -- Although the MLB clock exists in the clock tree as a better rate provider, it might not be correctly enabled or running at the rate it claims. > Maybe there's something wrong with rxtx6 (IMX6QDL_CLK_MLB). This clock Yes. > does not seem to be used elsewhere (I mean in files, it's used in any > board that includes imx6qdl.dtsi) > > > include/dt-bindings/clock/imx6qdl-clock.h: > #define IMX6QDL_CLK_MLB 139 > Might it have to do with the fact I'm using (still trying in fact) to use etnaviv ? > > drivers/clk/imx/clk-imx6q.c: > > if (clk_on_imx6dl()) > /* > * The multiplexer and divider of the imx6q clock gpu2d get > * redefined/reused as mlb_sys_sel and mlb_sys_clk_podf on imx6dl. > */ > clk[IMX6QDL_CLK_MLB] = imx_clk_gate2("mlb", "gpu2d_core_podf", base + 0x74, 18); > else > clk[IMX6QDL_CLK_MLB] = imx_clk_gate2("mlb", "axi", base + 0x74, 18); > > > But I'm on a imx6q not imx6dl . There are five MLB clocks sharing the same clock gate according to CCM chapter in the Reference Manual of imx6q. But five clocks come from three different parent clocks, and I am wondering if the MLB clock that's connected to the S/PDIF module is really derived from this AXI. Hope Fabio might be able to help on the clock tree issue here:) > --- linux-4.7-no-spdif-out/arch/arm/boot/dts/imx6qdl.dtsi 2016-07-25 00:19:43.000000000 +0200 > +++ linux-4.7/arch/arm/boot/dts/imx6qdl.dtsi 2016-08-30 12:51:37.369431791 +0200 > @@ -242,7 +242,7 @@ > clocks = <&clks IMX6QDL_CLK_SPDIF_GCLK>, <&clks IMX6QDL_CLK_OSC>, > <&clks IMX6QDL_CLK_SPDIF>, <&clks IMX6QDL_CLK_ASRC>, > <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_ESAI_EXTAL>, > - <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_MLB>, > + <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_DUMMY>, As MLB might be gated or not available at all, disabling it is a quick work around. > AFAICS it just uses rxtx5 (IMX6QDL_CLK_IPG) for 32KHz and gets a little closer to that. > But I haven't tried to play at 32KHz > > Is there anything else I can try ? Another solution for you could be to change the rates of two of those existing clocks to the perfect rates for 44.1KHz and 48KHz respectively, 22579200Hz and 24576000Hz for example. (If you only need one sample rate support, changing rxtx1 SPDIF clock only then.) ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Setting some clocks back to DUMMY fixes spdif output on imx6q wandboard rev B1 2016-08-31 4:21 ` Nicolin Chen @ 2016-08-31 9:10 ` Xavi Drudis Ferran 2016-08-31 13:11 ` [alsa-devel] " Fabio Estevam 0 siblings, 1 reply; 12+ messages in thread From: Xavi Drudis Ferran @ 2016-08-31 9:10 UTC (permalink / raw) To: Nicolin Chen Cc: Xavi Drudis Ferran, fabio.estevam, Timur Tabi, Xiubo Li, Shengjiu Wang, alsa-devel, linuxppc-dev El Tue, Aug 30, 2016 at 09:21:01PM -0700, Nicolin Chen deia: > > No, the problem is not at the rate but the source -- Although the > MLB clock exists in the clock tree as a better rate provider, it > might not be correctly enabled or running at the rate it claims. > > > There are five MLB clocks sharing the same clock gate according > to CCM chapter in the Reference Manual of imx6q. But five clocks > come from three different parent clocks, and I am wondering if > the MLB clock that's connected to the S/PDIF module is really > derived from this AXI. > > Hope Fabio might be able to help on the clock tree issue here:) > I hope too, it's a little over my head, to be euphemistic. > > Another solution for you could be to change the rates of two of > those existing clocks to the perfect rates for 44.1KHz and 48KHz > respectively, 22579200Hz and 24576000Hz for example. (If you > only need one sample rate support, changing rxtx1 SPDIF clock > only then.) Thank you very much. I'm not sure what practical problem that would solve for me, audio sounds quite right to my ears with the workaround (disabling MLB). I've looked page 121 of http://cache.freescale.com/files/32bit/doc/data_sheet/IMX6DQIEC.pdf And it seems like the the margin for the SPDIF clock would be 16 ns and I'm like 10 times out of spec. But I can't hear the problem. I may try it one day to hear how it sounds. I'll try to remember it if I ever come across some problem with my audio. For now what I'd like is to stay as close to linux-libre mainline as possible, so the quick workaround is enough for me. Now for the general case, I'm not sure what the solution should be. Page 4 of the pdf above says MLB is not present in industrial "parts", only automotive, or consumer "parts". There are several versions of IMX6Q in the market. What version must I have ? I guess consumer (with MLB) but I'm not sure... According to the wandboard-quad-rev-b1 manual its consumer, MCIMX6Q5EYM10AC, so I should have MLB, I guess. $ cat /proc/cpuinfo processor : 0 model name : ARMv7 Processor rev 10 (v7l) BogoMIPS : 7.54 Features : half thumb fastmult vfp edsp thumbee neon vfpv3 tls vfpd32 CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x2 CPU part : 0xc09 CPU revision : 10 [...] I can't tell what CPU part : 0xc09 means. In the reference manual pg 796 I see the same gate seems to affect Media Local Bus (MLB) clock and Digital Transmission Content Protection (DTCP). I don't use DTCP but I haven't done anything to disable it. http://www.nxp.com/files/32bit/doc/ref_manual/IMX6DQRM.pdf?fasp=1&WT_TYPE=Reference%20Manuals&WT_VENDOR=FREESCALE&WT_FILE_FORMAT=pdf&WT_ASSET=Documentation&fileExt=.pdf Thanks again, you've been very helpful. ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [alsa-devel] Setting some clocks back to DUMMY fixes spdif output on imx6q wandboard rev B1 2016-08-31 9:10 ` Xavi Drudis Ferran @ 2016-08-31 13:11 ` Fabio Estevam 2016-08-31 13:30 ` Fabio Estevam 2016-08-31 13:49 ` Xavi Drudis Ferran 0 siblings, 2 replies; 12+ messages in thread From: Fabio Estevam @ 2016-08-31 13:11 UTC (permalink / raw) To: Xavi Drudis Ferran Cc: Nicolin Chen, Shengjiu Wang, alsa-devel@alsa-project.org, Xiubo Li, Timur Tabi, Fabio Estevam, linuxppc-dev@lists.ozlabs.org Hi Xavi/Nicolin, On Wed, Aug 31, 2016 at 6:10 AM, Xavi Drudis Ferran <xdrudis@tinet.cat> wrote: > El Tue, Aug 30, 2016 at 09:21:01PM -0700, Nicolin Chen deia: >> >> No, the problem is not at the rate but the source -- Although the >> MLB clock exists in the clock tree as a better rate provider, it >> might not be correctly enabled or running at the rate it claims. >> > >> >> There are five MLB clocks sharing the same clock gate according >> to CCM chapter in the Reference Manual of imx6q. But five clocks >> come from three different parent clocks, and I am wondering if >> the MLB clock that's connected to the S/PDIF module is really >> derived from this AXI. >> >> Hope Fabio might be able to help on the clock tree issue here:) >> > > I hope too, it's a little over my head, to be euphemistic. > >> >> Another solution for you could be to change the rates of two of >> those existing clocks to the perfect rates for 44.1KHz and 48KHz >> respectively, 22579200Hz and 24576000Hz for example. (If you >> only need one sample rate support, changing rxtx1 SPDIF clock >> only then.) > > Thank you very much. I'm not sure what practical problem that would > solve for me, audio sounds quite right to my ears with the workaround > (disabling MLB). I've looked page 121 of > http://cache.freescale.com/files/32bit/doc/data_sheet/IMX6DQIEC.pdf > And it seems like the the margin for the SPDIF clock would be 16 ns > and I'm like 10 times out of spec. But I can't hear the problem. I > may try it one day to hear how it sounds. > > I'll try to remember it if I ever come across some problem with my audio. > For now what I'd like is to stay as close to linux-libre mainline > as possible, so the quick workaround is enough for me. > > Now for the general case, I'm not sure what the solution should be. > Page 4 of the pdf above says MLB is not present in industrial "parts", > only automotive, or consumer "parts". There are several versions of > IMX6Q in the market. What version must I have ? I guess consumer > (with MLB) but I'm not sure... According to the wandboard-quad-rev-b1 > manual its consumer, MCIMX6Q5EYM10AC, so I should have MLB, I guess. > > $ cat /proc/cpuinfo > processor : 0 > model name : ARMv7 Processor rev 10 (v7l) > BogoMIPS : 7.54 > Features : half thumb fastmult vfp edsp thumbee neon vfpv3 tls vfpd32 > CPU implementer : 0x41 > CPU architecture: 7 > CPU variant : 0x2 > CPU part : 0xc09 > CPU revision : 10 > [...] > > I can't tell what CPU part : 0xc09 means. > > In the reference manual pg 796 I see the same gate seems to affect Media > Local Bus (MLB) clock and Digital Transmission Content Protection > (DTCP). I don't use DTCP but I haven't done anything to disable it. > > http://www.nxp.com/files/32bit/doc/ref_manual/IMX6DQRM.pdf?fasp=1&WT_TYPE=Reference%20Manuals&WT_VENDOR=FREESCALE&WT_FILE_FORMAT=pdf&WT_ASSET=Documentation&fileExt=.pdf Sorry for the delay. As far as I can see, there are two current issues: 1. Regression caused by: 833f2cbf7091099bae ("ARM: dts: imx6: change the core clock of spdif"). Looks like that this commit did much more than just changing the core clock of spdif. It does not mention why MLB clock has been added. Looking at MX6Q RM I do not see the connection between MLB and SPDIF. So I agree with Xavi's suggestion of using the dummy_clk instead of mlb clock. Xavi, Care to send a formal patch with your change? 2. SPDIF clock rate not accurate. Probably using PLL4 as SPDIF source would help to get more accurate SPDIF clock rates. Could you please try the untested change? --- a/drivers/clk/imx/clk-imx6q.c +++ b/drivers/clk/imx/clk-imx6q.c @@ -623,7 +623,7 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node) pr_warn("failed to set up CLKO: %d\n", ret); /* Audio-related clocks configuration */ - clk_set_parent(clk[IMX6QDL_CLK_SPDIF_SEL], clk[IMX6QDL_CLK_PLL3_PFD3_454M]); + clk_set_parent(clk[IMX6QDL_CLK_SPDIF_SEL], clk[IMX6QDL_CLK_PLL4_AUDIO_DIV]); /* All existing boards with PCIe use LVDS1 */ if (IS_ENABLED(CONFIG_PCI_IMX6)) Regards, Fabio Estevam ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [alsa-devel] Setting some clocks back to DUMMY fixes spdif output on imx6q wandboard rev B1 2016-08-31 13:11 ` [alsa-devel] " Fabio Estevam @ 2016-08-31 13:30 ` Fabio Estevam 2016-08-31 13:47 ` Xavi Drudis Ferran 2016-08-31 13:49 ` Xavi Drudis Ferran 1 sibling, 1 reply; 12+ messages in thread From: Fabio Estevam @ 2016-08-31 13:30 UTC (permalink / raw) To: Xavi Drudis Ferran Cc: Nicolin Chen, Shengjiu Wang, alsa-devel@alsa-project.org, Xiubo Li, Timur Tabi, Fabio Estevam, linuxppc-dev@lists.ozlabs.org Xavi, On Wed, Aug 31, 2016 at 10:11 AM, Fabio Estevam <festevam@gmail.com> wrote: > Xavi, > > Care to send a formal patch with your change? If you prefer, I can send this change to the ARM kernel mailing list. Please let me know what you prefer. Thanks ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [alsa-devel] Setting some clocks back to DUMMY fixes spdif output on imx6q wandboard rev B1 2016-08-31 13:30 ` Fabio Estevam @ 2016-08-31 13:47 ` Xavi Drudis Ferran 2016-08-31 14:02 ` Fabio Estevam 0 siblings, 1 reply; 12+ messages in thread From: Xavi Drudis Ferran @ 2016-08-31 13:47 UTC (permalink / raw) To: Fabio Estevam Cc: Xavi Drudis Ferran, Nicolin Chen, Shengjiu Wang, alsa-devel@alsa-project.org, Xiubo Li, Timur Tabi, Fabio Estevam, linuxppc-dev@lists.ozlabs.org El Wed, Aug 31, 2016 at 10:30:25AM -0300, Fabio Estevam deia: > Xavi, > > On Wed, Aug 31, 2016 at 10:11 AM, Fabio Estevam <festevam@gmail.com> wrote: > > > Xavi, > > > > Care to send a formal patch with your change? > > If you prefer, I can send this change to the ARM kernel mailing list. > Whatever is easier for you. I'll have to look up the formalities for sending the patch myself (format, copyright, where to send, etc.) since I've never sent a patch for linux. I don't believe such a simple change can be copyrightable, but the original isn't mine, it's from that URL I gave, https://community.nxp.com/thread/387131 so originally from ambika@iwavesystems.com > Please let me know what you prefer. > If it's easy for you to send it yourself, I would prefer so and I'm grateful. If not, it'll be an exercise for me, no problem. ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [alsa-devel] Setting some clocks back to DUMMY fixes spdif output on imx6q wandboard rev B1 2016-08-31 13:47 ` Xavi Drudis Ferran @ 2016-08-31 14:02 ` Fabio Estevam 0 siblings, 0 replies; 12+ messages in thread From: Fabio Estevam @ 2016-08-31 14:02 UTC (permalink / raw) To: Xavi Drudis Ferran Cc: Nicolin Chen, Shengjiu Wang, alsa-devel@alsa-project.org, Xiubo Li, Timur Tabi, Fabio Estevam, linuxppc-dev@lists.ozlabs.org Hi Xavi, On Wed, Aug 31, 2016 at 10:47 AM, Xavi Drudis Ferran <xdrudis@tinet.cat> wrote: > If it's easy for you to send it yourself, I would prefer so and I'm > grateful. If not, it'll be an exercise for me, no problem. I have just submitted the patch with you on Cc. If you could reply to it with your Tested-by tag, that would be great. Thanks ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [alsa-devel] Setting some clocks back to DUMMY fixes spdif output on imx6q wandboard rev B1 2016-08-31 13:11 ` [alsa-devel] " Fabio Estevam 2016-08-31 13:30 ` Fabio Estevam @ 2016-08-31 13:49 ` Xavi Drudis Ferran 2016-08-31 17:49 ` Xavi Drudis Ferran 1 sibling, 1 reply; 12+ messages in thread From: Xavi Drudis Ferran @ 2016-08-31 13:49 UTC (permalink / raw) To: Fabio Estevam Cc: Xavi Drudis Ferran, Nicolin Chen, Shengjiu Wang, alsa-devel@alsa-project.org, Xiubo Li, Timur Tabi, Fabio Estevam, linuxppc-dev@lists.ozlabs.org El Wed, Aug 31, 2016 at 10:11:13AM -0300, Fabio Estevam deia: > 2. SPDIF clock rate not accurate. Probably using PLL4 as SPDIF source > would help to get more accurate SPDIF clock rates. > > Could you please try the untested change? > > --- a/drivers/clk/imx/clk-imx6q.c > +++ b/drivers/clk/imx/clk-imx6q.c > @@ -623,7 +623,7 @@ static void __init imx6q_clocks_init(struct > device_node *ccm_node) > pr_warn("failed to set up CLKO: %d\n", ret); > > /* Audio-related clocks configuration */ > - clk_set_parent(clk[IMX6QDL_CLK_SPDIF_SEL], > clk[IMX6QDL_CLK_PLL3_PFD3_454M]); > + clk_set_parent(clk[IMX6QDL_CLK_SPDIF_SEL], > clk[IMX6QDL_CLK_PLL4_AUDIO_DIV]); > > /* All existing boards with PCIe use LVDS1 */ > if (IS_ENABLED(CONFIG_PCI_IMX6)) > I'm going to try. I'll take a while. I'll report the result later. Thank you very much. ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [alsa-devel] Setting some clocks back to DUMMY fixes spdif output on imx6q wandboard rev B1 2016-08-31 13:49 ` Xavi Drudis Ferran @ 2016-08-31 17:49 ` Xavi Drudis Ferran 2016-08-31 18:02 ` Fabio Estevam 0 siblings, 1 reply; 12+ messages in thread From: Xavi Drudis Ferran @ 2016-08-31 17:49 UTC (permalink / raw) To: Fabio Estevam Cc: Xavi Drudis Ferran, Nicolin Chen, Shengjiu Wang, alsa-devel@alsa-project.org, Xiubo Li, Timur Tabi, Fabio Estevam, linuxppc-dev@lists.ozlabs.org El Wed, Aug 31, 2016 at 03:49:25PM +0200, Xavi Drudis Ferran deia: > El Wed, Aug 31, 2016 at 10:11:13AM -0300, Fabio Estevam deia: > > 2. SPDIF clock rate not accurate. Probably using PLL4 as SPDIF source > > would help to get more accurate SPDIF clock rates. > > > > Could you please try the untested change? > > > > --- a/drivers/clk/imx/clk-imx6q.c > > +++ b/drivers/clk/imx/clk-imx6q.c > > @@ -623,7 +623,7 @@ static void __init imx6q_clocks_init(struct > > device_node *ccm_node) > > pr_warn("failed to set up CLKO: %d\n", ret); > > > > /* Audio-related clocks configuration */ > > - clk_set_parent(clk[IMX6QDL_CLK_SPDIF_SEL], > > clk[IMX6QDL_CLK_PLL3_PFD3_454M]); > > + clk_set_parent(clk[IMX6QDL_CLK_SPDIF_SEL], > > clk[IMX6QDL_CLK_PLL4_AUDIO_DIV]); > > > > /* All existing boards with PCIe use LVDS1 */ > > if (IS_ENABLED(CONFIG_PCI_IMX6)) > > > > I'm going to try. I'll take a while. I'll report the result later. > > Thank you very much. I just tried. Spdif output still works. I can't hear any difference. I've summarised the tests in a table: Nominal Hz 32000 44100 48000 96000 192000 ns 31250 22676 20833 10417 5208 Linux-libre-4.7 (unchanged) (no spdif output) Hz 32226 43882 47965 95930 196428 ns 31031 22788 20849 10424 5091 deviation(ns) 219 -113 -15 -8 117 only core (SPDIF_GCLK), rxtx0 (CLK_OSC), rxtx1(SPDIF) & spba (spdif output) Hz 31719 43859 47368 94736 187500 ns 31527 22800 21111 10556 5333 deviation(ns) -277 -125 -278 -139 -125 without MLB (the rest unchanged) (spdif output) Hz 32226 43859 47368 94736 187500 ns 31031 22800 21111 10556 5333 deviation(ns) 219 -125 -278 -139 -125 without MLB, and PLL4 instead of PLL3 for SPDIF (spdif output) Hz 32226 44836 49107 93750 187500 ns 31031 22304 20364 10667 5333 deviation(ns) 219 372 470 -250 -125 I saw page 121 of http://cache.freescale.com/files/32bit/doc/data_sheet/IMX6DQIEC.pdf And it seems like the the margin for the SPDIF clock would be 16 ns so I've just inverted the frequencies to compare, but I'm not convinced it's relevant. Here's the extract from dmesg with your patch (and .dtsi like mainline except MLB replaced with DUMMY). [...] [ 7.517394] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 7.578089] imx_thermal 2000000.aips-bus:tempmon: Extended Commercial CPU temperature grade - max:105C critical:100C passive:95C [ 7.594443] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 7.594454] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 7.594459] etnaviv-gpu 2204000.gpu: hw init failed: -6 [ 7.653041] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe [ 7.656319] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.704159] fsl-spdif-dai 2004000.spdif: use rxtx5 as tx clock source for 32000Hz sample rate [ 7.711719] fsl-spdif-dai 2004000.spdif: use txclk df 16 for 32000Hz sample rate [ 7.718328] fsl-spdif-dai 2004000.spdif: use sysclk df 2 for 32000Hz sample rate [ 7.724762] fsl-spdif-dai 2004000.spdif: the best rate for 32000Hz sample rate is 32226Hz [ 7.732679] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.760087] fsl-spdif-dai 2004000.spdif: use rxtx5 as tx clock source for 44100Hz sample rate [ 7.766536] fsl-spdif-dai 2004000.spdif: use txclk df 1 for 44100Hz sample rate [ 7.772986] fsl-spdif-dai 2004000.spdif: use sysclk df 23 for 44100Hz sample rate [ 7.780120] fsl-spdif-dai 2004000.spdif: the best rate for 44100Hz sample rate is 44836Hz [ 7.788952] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.825238] fsl-spdif-dai 2004000.spdif: use rxtx5 as tx clock source for 48000Hz sample rate [ 7.831515] fsl-spdif-dai 2004000.spdif: use txclk df 7 for 48000Hz sample rate [ 7.837583] fsl-spdif-dai 2004000.spdif: use sysclk df 3 for 48000Hz sample rate [ 7.843718] fsl-spdif-dai 2004000.spdif: the best rate for 48000Hz sample rate is 49107Hz [ 7.849672] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.878632] fsl-spdif-dai 2004000.spdif: use rxtx0 as tx clock source for 96000Hz sample rate [ 7.884550] fsl-spdif-dai 2004000.spdif: use txclk df 4 for 96000Hz sample rate [ 7.890390] fsl-spdif-dai 2004000.spdif: the best rate for 96000Hz sample rate is 93750Hz [ 7.896253] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.921228] fsl-spdif-dai 2004000.spdif: use rxtx0 as tx clock source for 192000Hz sample rate [ 7.927034] fsl-spdif-dai 2004000.spdif: use txclk df 2 for 192000Hz sample rate [ 7.932809] fsl-spdif-dai 2004000.spdif: the best rate for 192000Hz sample rate is 187500Hz [ 7.938616] fsl-spdif-dai 2004000.spdif: imx_pcm_dma_init failed: -517 [ 7.944791] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW [ 7.954697] fsl-asrc 2034000.asrc: driver registered [ 7.961411] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe [ 7.967622] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 7.992427] fsl-spdif-dai 2004000.spdif: use rxtx5 as tx clock source for 32000Hz sample rate [ 7.998228] fsl-spdif-dai 2004000.spdif: use txclk df 16 for 32000Hz sample rate [ 8.004122] fsl-spdif-dai 2004000.spdif: use sysclk df 2 for 32000Hz sample rate [ 8.009806] fsl-spdif-dai 2004000.spdif: the best rate for 32000Hz sample rate is 32226Hz [ 8.015572] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 8.044534] fsl-spdif-dai 2004000.spdif: use rxtx5 as tx clock source for 44100Hz sample rate [ 8.050294] fsl-spdif-dai 2004000.spdif: use txclk df 1 for 44100Hz sample rate [ 8.056069] fsl-spdif-dai 2004000.spdif: use sysclk df 23 for 44100Hz sample rate [ 8.061869] fsl-spdif-dai 2004000.spdif: the best rate for 44100Hz sample rate is 44836Hz [ 8.067662] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 8.092093] fsl-spdif-dai 2004000.spdif: use rxtx5 as tx clock source for 48000Hz sample rate [ 8.097916] fsl-spdif-dai 2004000.spdif: use txclk df 7 for 48000Hz sample rate [ 8.103769] fsl-spdif-dai 2004000.spdif: use sysclk df 3 for 48000Hz sample rate [ 8.109660] fsl-spdif-dai 2004000.spdif: the best rate for 48000Hz sample rate is 49107Hz [ 8.115488] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 8.141250] fsl-spdif-dai 2004000.spdif: use rxtx0 as tx clock source for 96000Hz sample rate [ 8.147179] fsl-spdif-dai 2004000.spdif: use txclk df 4 for 96000Hz sample rate [ 8.153066] fsl-spdif-dai 2004000.spdif: the best rate for 96000Hz sample rate is 93750Hz [ 8.158900] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 8.185506] fsl-spdif-dai 2004000.spdif: use rxtx0 as tx clock source for 192000Hz sample rate [ 8.191441] fsl-spdif-dai 2004000.spdif: use txclk df 2 for 192000Hz sample rate [ 8.197297] fsl-spdif-dai 2004000.spdif: the best rate for 192000Hz sample rate is 187500Hz [ 8.203477] fsl-spdif-dai 2004000.spdif: imx_pcm_dma_init failed: -517 [ 8.210220] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW [ 8.653296] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe [ 8.678782] imx-spdif sound-spdif: ASoC: CPU DAI (null) not registered [ 8.682393] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 8.705822] imx-spdif sound-spdif: snd_soc_register_card failed: -517 [ 8.735316] fsl-spdif-dai 2004000.spdif: use rxtx5 as tx clock source for 32000Hz sample rate [ 8.741460] fsl-spdif-dai 2004000.spdif: use txclk df 16 for 32000Hz sample rate [ 8.747889] fsl-spdif-dai 2004000.spdif: use sysclk df 2 for 32000Hz sample rate [ 8.754006] fsl-spdif-dai 2004000.spdif: the best rate for 32000Hz sample rate is 32226Hz [ 8.755063] sgtl5000 1-000a: sgtl5000 revision 0x11 [...] [ 8.776463] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 8.804281] fsl-spdif-dai 2004000.spdif: use rxtx5 as tx clock source for 44100Hz sample rate [ 8.810549] fsl-spdif-dai 2004000.spdif: use txclk df 1 for 44100Hz sample rate [ 8.816670] fsl-spdif-dai 2004000.spdif: use sysclk df 23 for 44100Hz sample rate [ 8.822881] fsl-spdif-dai 2004000.spdif: the best rate for 44100Hz sample rate is 44836Hz [ 8.829149] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 8.857633] fsl-spdif-dai 2004000.spdif: use rxtx5 as tx clock source for 48000Hz sample rate [ 8.864664] fsl-spdif-dai 2004000.spdif: use txclk df 7 for 48000Hz sample rate [ 8.871299] fsl-spdif-dai 2004000.spdif: use sysclk df 3 for 48000Hz sample rate [ 8.878169] fsl-spdif-dai 2004000.spdif: the best rate for 48000Hz sample rate is 49107Hz [ 8.885341] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 8.887272] 20ec000.sdma: Missing Free firmware (non-Free firmware loading is disabled) [ 8.887325] imx-sdma 20ec000.sdma: failed to get firmware from device tree [ 8.928411] fsl-spdif-dai 2004000.spdif: use rxtx0 as tx clock source for 96000Hz sample rate [ 8.932841] imx-sdma 20ec000.sdma: Direct firmware load for /*(DEBLOBBED)*/ failed with error -2 [ 8.941518] fsl-spdif-dai 2004000.spdif: use txclk df 4 for 96000Hz sample rate [ 8.948104] fsl-spdif-dai 2004000.spdif: the best rate for 96000Hz sample rate is 93750Hz [ 8.954948] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 8.985543] fsl-spdif-dai 2004000.spdif: use rxtx0 as tx clock source for 192000Hz sample rate [ 8.992121] fsl-spdif-dai 2004000.spdif: use txclk df 2 for 192000Hz sample rate [ 8.998731] fsl-spdif-dai 2004000.spdif: the best rate for 192000Hz sample rate is 187500Hz [...] [ 9.013319] fsl-spdif-dai 2004000.spdif: imx_pcm_dma_init failed: -517 [ 9.029511] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW [ 9.052247] imx-spdif sound-spdif: ASoC: CPU DAI (null) not registered [ 9.061522] imx-spdif sound-spdif: snd_soc_register_card failed: -517 [ 9.072088] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe [ 9.087019] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 9.120952] fsl-spdif-dai 2004000.spdif: use rxtx5 as tx clock source for 32000Hz sample rate [ 9.128069] fsl-spdif-dai 2004000.spdif: use txclk df 16 for 32000Hz sample rate [ 9.135255] fsl-spdif-dai 2004000.spdif: use sysclk df 2 for 32000Hz sample rate [ 9.142316] fsl-spdif-dai 2004000.spdif: the best rate for 32000Hz sample rate is 32226Hz [ 9.149247] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 9.181927] fsl-spdif-dai 2004000.spdif: use rxtx5 as tx clock source for 44100Hz sample rate [ 9.188687] sgtl5000 1-000a: Using internal LDO instead of VDDD [ 9.196207] fsl-spdif-dai 2004000.spdif: use txclk df 1 for 44100Hz sample rate [ 9.203005] fsl-spdif-dai 2004000.spdif: use sysclk df 23 for 44100Hz sample rate [ 9.209998] fsl-spdif-dai 2004000.spdif: the best rate for 44100Hz sample rate is 44836Hz [ 9.216928] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 9.250153] fsl-spdif-dai 2004000.spdif: use rxtx5 as tx clock source for 48000Hz sample rate [ 9.256987] fsl-spdif-dai 2004000.spdif: use txclk df 7 for 48000Hz sample rate [ 9.263890] fsl-spdif-dai 2004000.spdif: use sysclk df 3 for 48000Hz sample rate [ 9.270641] fsl-spdif-dai 2004000.spdif: the best rate for 48000Hz sample rate is 49107Hz [ 9.277343] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 9.305524] fsl-spdif-dai 2004000.spdif: use rxtx0 as tx clock source for 96000Hz sample rate [ 9.312400] fsl-spdif-dai 2004000.spdif: use txclk df 4 for 96000Hz sample rate [ 9.319041] fsl-spdif-dai 2004000.spdif: the best rate for 96000Hz sample rate is 93750Hz [ 9.325799] fsl-spdif-dai 2004000.spdif: enter fsl_spdif_probe_txclk [ 9.354693] fsl-asoc-card sound: sgtl5000 <-> 2028000.ssi mapping ok [ 9.357288] fsl-spdif-dai 2004000.spdif: use rxtx0 as tx clock source for 192000Hz sample rate [ 9.357293] fsl-spdif-dai 2004000.spdif: use txclk df 2 for 192000Hz sample rate [ 9.357298] fsl-spdif-dai 2004000.spdif: the best rate for 192000Hz sample rate is 187500Hz [ 9.470268] imx-spdif sound-spdif: snd-soc-dummy-dai <-> 2004000.spdif mapping ok [...] [ 71.548012] fsl-spdif-dai 2004000.spdif: expected clock rate = 64915200 [ 71.548027] fsl-spdif-dai 2004000.spdif: actual clock rate = 66000000 [ 71.548043] fsl-spdif-dai 2004000.spdif: set sample rate to 44836Hz for 44100Hz playback [ 71.548054] fsl-spdif-dai 2004000.spdif: STCSCH: 0x304000 [ 71.548065] fsl-spdif-dai 2004000.spdif: STCSCL: 0x000000 [ 71.743796] fsl-spdif-dai 2004000.spdif: expected clock rate = 64915200 [ 71.743812] fsl-spdif-dai 2004000.spdif: actual clock rate = 66000000 [ 71.743823] fsl-spdif-dai 2004000.spdif: set sample rate to 44836Hz for 44100Hz playback [ 71.743844] fsl-spdif-dai 2004000.spdif: STCSCH: 0x304000 [ 71.743867] fsl-spdif-dai 2004000.spdif: STCSCL: 0x000000 And when playing sound (spdif output works ok) [ 128.778530] fsl-spdif-dai 2004000.spdif: expected clock rate = 64915200 [ 128.778549] fsl-spdif-dai 2004000.spdif: actual clock rate = 66000000 [ 128.778560] fsl-spdif-dai 2004000.spdif: set sample rate to 44836Hz for 44100Hz playback [ 128.778575] fsl-spdif-dai 2004000.spdif: STCSCH: 0x304000 [ 128.778583] fsl-spdif-dai 2004000.spdif: STCSCL: 0x000000 Thank you amd feel free to suggest more tests, but it is good enough as it is for me. ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [alsa-devel] Setting some clocks back to DUMMY fixes spdif output on imx6q wandboard rev B1 2016-08-31 17:49 ` Xavi Drudis Ferran @ 2016-08-31 18:02 ` Fabio Estevam 0 siblings, 0 replies; 12+ messages in thread From: Fabio Estevam @ 2016-08-31 18:02 UTC (permalink / raw) To: Xavi Drudis Ferran Cc: Nicolin Chen, Shengjiu Wang, alsa-devel@alsa-project.org, Xiubo Li, Timur Tabi, Fabio Estevam, linuxppc-dev@lists.ozlabs.org On Wed, Aug 31, 2016 at 2:49 PM, Xavi Drudis Ferran <xdrudis@tinet.cat> wrote: > Thank you amd feel free to suggest more tests, but it is good enough > as it is for me. Ok, thanks for trying. So let's keep the SPDIF parent clock as is. ^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2016-08-31 18:02 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <20160828160055.GA2122@begut>
2016-08-29 19:28 ` Setting some clocks back to DUMMY fixes spdif output on imx6q wandboard rev B1 Nicolin Chen
2016-08-29 19:54 ` Xavi Drudis Ferran
2016-08-30 11:14 ` Xavi Drudis Ferran
2016-08-31 4:21 ` Nicolin Chen
2016-08-31 9:10 ` Xavi Drudis Ferran
2016-08-31 13:11 ` [alsa-devel] " Fabio Estevam
2016-08-31 13:30 ` Fabio Estevam
2016-08-31 13:47 ` Xavi Drudis Ferran
2016-08-31 14:02 ` Fabio Estevam
2016-08-31 13:49 ` Xavi Drudis Ferran
2016-08-31 17:49 ` Xavi Drudis Ferran
2016-08-31 18:02 ` Fabio Estevam
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).