From: Nicholas Piggin <npiggin@gmail.com>
To: linuxppc-dev@lists.ozlabs.org
Cc: Nicholas Piggin <npiggin@gmail.com>,
"Gautham R . Shenoy" <ego@linux.vnet.ibm.com>,
"Shreyas B . Prabhu" <shreyas@linux.vnet.ibm.com>
Subject: [PATCH 00/14 v2] idle performance improvements
Date: Mon, 12 Jun 2017 09:58:21 +1000 [thread overview]
Message-ID: <20170611235835.7400-1-npiggin@gmail.com> (raw)
I rebased this on the powerpc next tree.
A couple of things are changed since last post:
- Patch 1 now properly accounts for the fact the powernv idle
wakeups do not re-enable interrupts until the cpuidle driver
enables them. This was not quite right in the previous patch
(and prep_irq_for_idle() is not quite right for that case so
a new primitive has to be introduced).
- Patch to replace interrupts from system reset wakeup changed
rather than replaying directly, it just marks the IRQ in the
lazy pending bit and it will get replayed at the right time
when irqs are re-enabled.
Thanks,
Nick
Nicholas Piggin (14):
powerpc/64s: idle move soft interrupt mask logic into C code
powerpc/64s: idle hotplug lazy-irq simplification
powerpc/64s: idle provide a default idle for POWER9
powerpc/64s: idle process interrupts from system reset wakeup
powerpc/64s: msgclr when handling doorbell exceptions
powerpc/64s: interrupt replay balance the return branch predictor
powerpc/64s: idle branch to handler with virtual mode offset
powerpc/64s: idle avoid SRR usage in idle sleep/wake paths
powerpc/64s: idle hmi wakeup is unlikely
powerpc/64s: cpuidle set polling before enabling irqs
powerpc/64s: cpuidle read mostly for common globals
powerpc/64s: cpuidle no memory barrier after break from idle
powerpc/64: runlatch CTRL[RUN] set optimisation
powerpc/64s: idle runlatch switch is done with MSR[EE]=0
arch/powerpc/include/asm/dbell.h | 13 +++
arch/powerpc/include/asm/exception-64s.h | 17 +++-
arch/powerpc/include/asm/hw_irq.h | 5 ++
arch/powerpc/include/asm/machdep.h | 1 +
arch/powerpc/include/asm/ppc-opcode.h | 3 +
arch/powerpc/include/asm/processor.h | 10 +--
arch/powerpc/kernel/asm-offsets.c | 1 +
arch/powerpc/kernel/exceptions-64s.S | 33 ++++++--
arch/powerpc/kernel/idle_book3s.S | 135 +++++++++----------------------
arch/powerpc/kernel/irq.c | 58 ++++++++++++-
arch/powerpc/kernel/process.c | 12 +--
arch/powerpc/kvm/book3s_hv_rmhandlers.S | 8 +-
arch/powerpc/platforms/powernv/idle.c | 90 +++++++++++++++++++--
arch/powerpc/platforms/powernv/smp.c | 31 ++++---
arch/powerpc/platforms/powernv/subcore.c | 3 +-
drivers/cpuidle/cpuidle-powernv.c | 37 +++++----
drivers/cpuidle/cpuidle-pseries.c | 22 +++--
17 files changed, 309 insertions(+), 170 deletions(-)
--
2.11.0
next reply other threads:[~2017-06-12 0:00 UTC|newest]
Thread overview: 44+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-06-11 23:58 Nicholas Piggin [this message]
2017-06-11 23:58 ` [PATCH 01/14] powerpc/64s: idle move soft interrupt mask logic into C code Nicholas Piggin
2017-06-12 8:37 ` Gautham R Shenoy
2017-06-12 14:46 ` Nicholas Piggin
2017-06-13 4:28 ` Gautham R Shenoy
2017-06-11 23:58 ` [PATCH 02/14] powerpc/64s: idle hotplug lazy-irq simplification Nicholas Piggin
2017-06-11 23:58 ` [PATCH 03/14] powerpc/64s: idle provide a default idle for POWER9 Nicholas Piggin
2017-06-12 8:53 ` Gautham R Shenoy
2017-06-12 14:46 ` Nicholas Piggin
2017-06-11 23:58 ` [PATCH 04/14] powerpc/64s: idle process interrupts from system reset wakeup Nicholas Piggin
2017-06-12 9:41 ` Gautham R Shenoy
2017-06-12 14:51 ` Nicholas Piggin
2017-06-11 23:58 ` [PATCH 05/14] powerpc/64s: msgclr when handling doorbell exceptions Nicholas Piggin
2017-06-12 14:38 ` Gautham R Shenoy
2017-06-11 23:58 ` [PATCH 06/14] powerpc/64s: interrupt replay balance the return branch predictor Nicholas Piggin
2017-06-12 14:41 ` Gautham R Shenoy
2017-06-13 9:51 ` Michael Ellerman
2017-06-13 11:09 ` Nicholas Piggin
2017-06-11 23:58 ` [PATCH 07/14] powerpc/64s: idle branch to handler with virtual mode offset Nicholas Piggin
2017-06-11 23:58 ` [PATCH 08/14] powerpc/64s: idle avoid SRR usage in idle sleep/wake paths Nicholas Piggin
2017-06-13 10:25 ` Gautham R Shenoy
2017-06-13 10:45 ` Nicholas Piggin
2017-06-11 23:58 ` [PATCH 09/14] powerpc/64s: idle hmi wakeup is unlikely Nicholas Piggin
2017-06-12 15:03 ` Gautham R Shenoy
2017-06-11 23:58 ` [PATCH 10/14] powerpc/64s: cpuidle set polling before enabling irqs Nicholas Piggin
2017-06-12 15:10 ` Gautham R Shenoy
2017-06-12 15:20 ` Nicholas Piggin
2017-06-11 23:58 ` [PATCH 11/14] powerpc/64s: cpuidle read mostly for common globals Nicholas Piggin
2017-06-12 15:30 ` Gautham R Shenoy
2017-06-12 17:50 ` Vaidyanathan Srinivasan
2017-06-11 23:58 ` [PATCH 12/14] powerpc/64s: cpuidle no memory barrier after break from idle Nicholas Piggin
2017-06-12 17:48 ` Vaidyanathan Srinivasan
2017-06-13 12:47 ` Nicholas Piggin
2017-06-11 23:58 ` [PATCH 13/14] powerpc/64: runlatch CTRL[RUN] set optimisation Nicholas Piggin
2017-06-12 17:11 ` Vaidyanathan Srinivasan
2017-06-13 10:04 ` Michael Ellerman
2017-06-13 11:56 ` Nicholas Piggin
2017-06-13 13:45 ` Benjamin Herrenschmidt
2017-06-14 3:34 ` Michael Ellerman
2017-06-11 23:58 ` [PATCH 14/14] powerpc/64s: idle runlatch switch is done with MSR[EE]=0 Nicholas Piggin
2017-06-12 17:00 ` Vaidyanathan Srinivasan
-- strict thread matches above, loose matches on Subject: below --
2017-06-11 9:30 [PATCH 00/14 v2] idle performance improvements Nicholas Piggin
2017-06-12 4:25 ` Benjamin Herrenschmidt
2017-06-12 5:47 ` Nicholas Piggin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170611235835.7400-1-npiggin@gmail.com \
--to=npiggin@gmail.com \
--cc=ego@linux.vnet.ibm.com \
--cc=linuxppc-dev@lists.ozlabs.org \
--cc=shreyas@linux.vnet.ibm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).