Re: RCU lockup issues when CONFIG_SOFTLOCKUP_DETECTOR=n - any one else seeing this?

[Jonathan Cameron <Jonathan.Cameron@huawei.com>]

On Wed, 26 Jul 2017 15:23:15 +0100
Jonathan Cameron <Jonathan.Cameron@huawei.com> wrote:

> On Wed, 26 Jul 2017 07:14:17 -0700
> "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> wrote:
> 
> > On Wed, Jul 26, 2017 at 01:28:01PM +0100, Jonathan Cameron wrote:  
> > > On Wed, 26 Jul 2017 10:32:32 +0100
> > > Jonathan Cameron <Jonathan.Cameron@huawei.com> wrote:
> > >     
> > > > On Wed, 26 Jul 2017 09:16:23 +0100
> > > > Jonathan Cameron <Jonathan.Cameron@huawei.com> wrote:
> > > >     
> > > > > On Tue, 25 Jul 2017 21:12:17 -0700
> > > > > "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> wrote:
> > > > >       
> > > > > > On Tue, Jul 25, 2017 at 09:02:33PM -0700, David Miller wrote:        
> > > > > > > From: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
> > > > > > > Date: Tue, 25 Jul 2017 20:55:45 -0700
> > > > > > >           
> > > > > > > > On Tue, Jul 25, 2017 at 02:10:29PM -0700, David Miller wrote:          
> > > > > > > >> Just to report, turning softlockup back on fixes things for me on
> > > > > > > >> sparc64 too.          
> > > > > > > > 
> > > > > > > > Very good!
> > > > > > > >           
> > > > > > > >> The thing about softlockup is it runs an hrtimer, which seems to run
> > > > > > > >> about every 4 seconds.          
> > > > > > > > 
> > > > > > > > I could see where that could shake things loose, but I am surprised that
> > > > > > > > it would be needed.  I ran a short run with CONFIG_SOFTLOCKUP_DETECTOR=y
> > > > > > > > with no trouble, but I will be running a longer test later on.
> > > > > > > >           
> > > > > > > >> So I wonder if this is a NO_HZ problem.          
> > > > > > > > 
> > > > > > > > Might be.  My tests run with NO_HZ_FULL=n and NO_HZ_IDLE=y.  What are
> > > > > > > > you running?  (Again, my symptoms are slightly different, so I might
> > > > > > > > be seeing a different bug.)          
> > > > > > > 
> > > > > > > I run with NO_HZ_FULL=n and NO_HZ_IDLE=y, just like you.
> > > > > > > 
> > > > > > > To clarify, the symptoms show up with SOFTLOCKUP_DETECTOR disabled.          
> > > > > > 
> > > > > > Same here -- but my failure case happens fairly rarely, so it will take
> > > > > > some time to gain reasonable confidence that enabling SOFTLOCKUP_DETECTOR
> > > > > > had effect.
> > > > > > 
> > > > > > But you are right, might be interesting to try NO_HZ_PERIODIC=y
> > > > > > or NO_HZ_FULL=y.  So many possible tests, and so little time.  ;-)
> > > > > > 
> > > > > > 							Thanx, Paul
> > > > > >         
> > > > > I'll be the headless chicken running around and trying as many tests
> > > > > as I can fit in.  Typical time to see the failure for us is sub 10
> > > > > minutes so we'll see how far we get.
> > > > > 
> > > > > Make me a list to run if you like ;)
> > > > > 
> > > > > NO_HZ_PERIODIC=y running now.      
> > > > By which I mean CONFIG_HZ_PERIODIC=y    
> > 
> > I did get that messed up, didn't I?  Sorry for my confusion!
> >   
> > > > Anyhow, run for 40 minutes with out seeing a splat but my sanity check
> > > > on the NO_FULL_HZ=n and NO_HZ_IDLE=y this morning took 20 minutes so
> > > > I won't have much confidence until we are a few hours in on this.
> > > > 
> > > > Anyhow, certainly looking like a promising direction for investigation!
> > > >     
> > > Well it's done over 3 hours without a splat so I think it is fine with
> > > CONFIG_HZ_PERIODIC=y    
> > 
> > Thank you!
> > 
> > If you run with SOFTLOCKUP_DETECTOR=n and NO_HZ_IDLE=y, but have a normal
> > user task waking up every few seconds on each CPU, does the problem occur?
> > (The question is whether any disturbance gets things going, or whether there
> > is something special about SOFTLOCKUP_DETECTOR=y and HZ_PERIODIC=y.
> > 
> > Dave, any other ideas on what might be causing this or what might be
> > tested?
> > 
> > 							Thanx, Paul
> >   
> 
> Although it's still early days (40 mins in) it looks like the issue first
> occurred between 4.10-rc7 and 4.11-rc1 (don't ask why those particular RCs)
> 
> Bad as with current kernel on 4.11-rc1 and good on 4.10-rc7.
Didn't leave it long enough. Still bad on 4.10-rc7 just took over
an hour to occur.
> 
> Could be something different was hiding it in 4.10 though.  We have a fair
> delta from mainline back then unfortunately so bisecting will be
> 'interesting'.
> 
> I'll see if I can get the test you suggest running.
> 
> Jonathan
> _______________________________________________
> linuxarm mailing list
> linuxarm@huawei.com
> http://rnd-openeuler.huawei.com/mailman/listinfo/linuxarm