[PATCH 1/5] powerpc/xive: Remove incorrect debug code

[PATCH 1/5] powerpc/xive: Remove incorrect debug code

[Benjamin Herrenschmidt]

WORD2 if the TIMA isn't byte accessible and
isn't that useful to know about, take out the
pr_devel statement.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
 arch/powerpc/sysdev/xive/common.c | 5 -----
 1 file changed, 5 deletions(-)

diff --git a/arch/powerpc/sysdev/xive/common.c b/arch/powerpc/sysdev/xive/common.c
index a3b8d7d1316e..838ebdbfe4c5 100644
--- a/arch/powerpc/sysdev/xive/common.c
+++ b/arch/powerpc/sysdev/xive/common.c
@@ -1269,11 +1269,6 @@ static void xive_setup_cpu(void)
 {
 	struct xive_cpu *xc = __this_cpu_read(xive_cpu);
 
-	/* Debug: Dump the TM state */
-	pr_devel("CPU %d [HW 0x%02x] VT=%02x\n",
-	    smp_processor_id(), hard_smp_processor_id(),
-	    in_8(xive_tima + xive_tima_offset + TM_WORD2));
-
 	/* The backend might have additional things to do */
 	if (xive_ops->setup_cpu)
 		xive_ops->setup_cpu(smp_processor_id(), xc);
-- 
2.14.3

[PATCH 2/5] powerpc: Remove DEBUG define in 64-bit early setup code

[Benjamin Herrenschmidt]

This statement causes some not very useful messages to always
be printed on the serial port at boot, even on quiet boots.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
 arch/powerpc/kernel/setup_64.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/arch/powerpc/kernel/setup_64.c b/arch/powerpc/kernel/setup_64.c
index 8956a9856604..d3124c302146 100644
--- a/arch/powerpc/kernel/setup_64.c
+++ b/arch/powerpc/kernel/setup_64.c
@@ -10,8 +10,6 @@
  *      2 of the License, or (at your option) any later version.
  */
 
-#define DEBUG
-
 #include <linux/export.h>
 #include <linux/string.h>
 #include <linux/sched.h>
-- 
2.14.3

[PATCH 3/5] powerpc: Reduce log level of "OPAL detected !" message

[Benjamin Herrenschmidt]

This message isn't terribly useful.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
 arch/powerpc/platforms/powernv/opal.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/powerpc/platforms/powernv/opal.c b/arch/powerpc/platforms/powernv/opal.c
index 041ddbd1fc57..2479e3396ed8 100644
--- a/arch/powerpc/platforms/powernv/opal.c
+++ b/arch/powerpc/platforms/powernv/opal.c
@@ -127,7 +127,7 @@ int __init early_init_dt_scan_opal(unsigned long node,
 
 	if (of_flat_dt_is_compatible(node, "ibm,opal-v3")) {
 		powerpc_firmware_features |= FW_FEATURE_OPAL;
-		pr_info("OPAL detected !\n");
+		pr_debug("OPAL detected !\n");
 	} else {
 		panic("OPAL != V3 detected, no longer supported.\n");
 	}
-- 
2.14.3

[PATCH 4/5] powerpc: Remove useless EXC_COMMON_HV

[Benjamin Herrenschmidt]

The only difference between EXC_COMMON_HV and EXC_COMMON is that the
former adds "2" to the trap number which is supposed to represent the
fact that this is an "HV" interrupt which uses HSRR0/1.

However KVM is the only one who cares and it has its own separate macros.

In fact, we only have one user of EXC_COMMON_HV and it's for an
unknown interrupt case. All the other ones already using EXC_COMMON.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
 arch/powerpc/include/asm/head-64.h   | 7 +------
 arch/powerpc/kernel/exceptions-64s.S | 2 +-
 2 files changed, 2 insertions(+), 7 deletions(-)

diff --git a/arch/powerpc/include/asm/head-64.h b/arch/powerpc/include/asm/head-64.h
index fdcff76e9a25..0a663dfc28b5 100644
--- a/arch/powerpc/include/asm/head-64.h
+++ b/arch/powerpc/include/asm/head-64.h
@@ -178,7 +178,7 @@ end_##sname:
  * TRAMP_REAL_*   - real, unrelocated helpers (virt can call these)
  * TRAMP_VIRT_*   - virt, unreloc helpers (in practice, real can use)
  * TRAMP_KVM      - KVM handlers that get put into real, unrelocated
- * EXC_COMMON_*   - virt, relocated common handlers
+ * EXC_COMMON     - virt, relocated common handlers
  *
  * The EXC handlers are given a name, and branch to name_common, or the
  * appropriate KVM or masking function. Vector handler verieties are as
@@ -211,7 +211,6 @@ end_##sname:
  * EXC_COMMON_BEGIN/END - used to open-code the handler
  * EXC_COMMON
  * EXC_COMMON_ASYNC
- * EXC_COMMON_HV
  *
  * TRAMP_REAL and TRAMP_VIRT can be used with BEGIN/END. KVM
  * and OOL handlers are implemented as types of TRAMP and TRAMP_VIRT handlers.
@@ -413,10 +412,6 @@ end_##sname:
 	EXC_COMMON_BEGIN(name);						\
 	STD_EXCEPTION_COMMON_ASYNC(realvec, name, hdlr);		\
 
-#define EXC_COMMON_HV(name, realvec, hdlr)				\
-	EXC_COMMON_BEGIN(name);						\
-	STD_EXCEPTION_COMMON(realvec + 0x2, name, hdlr);		\
-
 #endif /* __ASSEMBLY__ */
 
 #endif	/* _ASM_POWERPC_HEAD_64_H */
diff --git a/arch/powerpc/kernel/exceptions-64s.S b/arch/powerpc/kernel/exceptions-64s.S
index e441b469dc8f..175891c6909c 100644
--- a/arch/powerpc/kernel/exceptions-64s.S
+++ b/arch/powerpc/kernel/exceptions-64s.S
@@ -1318,7 +1318,7 @@ END_FTR_SECTION_IFSET(CPU_FTR_CFAR)
 	b	.
 #endif
 
-EXC_COMMON_HV(denorm_common, 0x1500, unknown_exception)
+EXC_COMMON(denorm_common, 0x1500, unknown_exception)
 
 
 #ifdef CONFIG_CBE_RAS
-- 
2.14.3

[PATCH 5/5] powerpc: Use the TRAP macro whenever comparing a trap number

[Benjamin Herrenschmidt]

Trap numbers can have extra bits at the bottom that need to
be filtered out. There are a few cases where we don't do that.

It's possible that we got lucky but better safe than sorry.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
 arch/powerpc/kernel/process.c | 2 +-
 arch/powerpc/kernel/traps.c   | 2 +-
 arch/powerpc/mm/fault.c       | 2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/powerpc/kernel/process.c b/arch/powerpc/kernel/process.c
index 72be0c32e902..397d6e64e3df 100644
--- a/arch/powerpc/kernel/process.c
+++ b/arch/powerpc/kernel/process.c
@@ -1409,7 +1409,7 @@ void show_regs(struct pt_regs * regs)
 	print_msr_bits(regs->msr);
 	pr_cont("  CR: %08lx  XER: %08lx\n", regs->ccr, regs->xer);
 	trap = TRAP(regs);
-	if ((regs->trap != 0xc00) && cpu_has_feature(CPU_FTR_CFAR))
+	if ((TRAP(regs) != 0xc00) && cpu_has_feature(CPU_FTR_CFAR))
 		pr_cont("CFAR: "REG" ", regs->orig_gpr3);
 	if (trap == 0x200 || trap == 0x300 || trap == 0x600)
 #if defined(CONFIG_4xx) || defined(CONFIG_BOOKE)
diff --git a/arch/powerpc/kernel/traps.c b/arch/powerpc/kernel/traps.c
index f3eb61be0d30..d61989be28e1 100644
--- a/arch/powerpc/kernel/traps.c
+++ b/arch/powerpc/kernel/traps.c
@@ -1564,7 +1564,7 @@ void facility_unavailable_exception(struct pt_regs *regs)
 	u8 status;
 	bool hv;
 
-	hv = (regs->trap == 0xf80);
+	hv = (TRAP(regs) == 0xf80);
 	if (hv)
 		value = mfspr(SPRN_HFSCR);
 	else
diff --git a/arch/powerpc/mm/fault.c b/arch/powerpc/mm/fault.c
index 6e1e39035380..7b15fe2ac986 100644
--- a/arch/powerpc/mm/fault.c
+++ b/arch/powerpc/mm/fault.c
@@ -576,7 +576,7 @@ void bad_page_fault(struct pt_regs *regs, unsigned long address, int sig)
 
 	/* kernel has accessed a bad area */
 
-	switch (regs->trap) {
+	switch (TRAP(regs)) {
 	case 0x300:
 	case 0x380:
 		printk(KERN_ALERT "Unable to handle kernel paging request for "
-- 
2.14.3

Re: [PATCH 3/5] powerpc: Reduce log level of "OPAL detected !" message

[Stewart Smith]

Benjamin Herrenschmidt <benh@kernel.crashing.org> writes:
> This message isn't terribly useful.
>
> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>

> --- a/arch/powerpc/platforms/powernv/opal.c
> +++ b/arch/powerpc/platforms/powernv/opal.c
> @@ -127,7 +127,7 @@ int __init early_init_dt_scan_opal(unsigned long node,
>
>  	if (of_flat_dt_is_compatible(node, "ibm,opal-v3")) {
>  		powerpc_firmware_features |= FW_FEATURE_OPAL;
> -		pr_info("OPAL detected !\n");
> +		pr_debug("OPAL detected !\n");

I've been meaning to add in a thing to grab the version from the device
tree and print that too.

-- 
Stewart Smith
OPAL Architect, IBM.

Re: [1/5] powerpc/xive: Remove incorrect debug code

[Michael Ellerman]

On Fri, 2018-01-12 at 02:28:45 UTC, Benjamin Herrenschmidt wrote:
> WORD2 if the TIMA isn't byte accessible and
> isn't that useful to know about, take out the
> pr_devel statement.
> 
> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Applied to powerpc next, thanks.

https://git.kernel.org/powerpc/c/f5abe14f88e8259494d69614768789

cheers

Re: [4/5] powerpc: Remove useless EXC_COMMON_HV

[Michael Ellerman]

On Fri, 2018-01-12 at 02:28:48 UTC, Benjamin Herrenschmidt wrote:
> The only difference between EXC_COMMON_HV and EXC_COMMON is that the
> former adds "2" to the trap number which is supposed to represent the
> fact that this is an "HV" interrupt which uses HSRR0/1.
> 
> However KVM is the only one who cares and it has its own separate macros.
> 
> In fact, we only have one user of EXC_COMMON_HV and it's for an
> unknown interrupt case. All the other ones already using EXC_COMMON.
> 
> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Applied to powerpc next, thanks.

https://git.kernel.org/powerpc/c/872e2ae4bdd4c244f7617ffc08c394

cheers

Re: [5/5] powerpc: Use the TRAP macro whenever comparing a trap number

[Michael Ellerman]

On Fri, 2018-01-12 at 02:28:49 UTC, Benjamin Herrenschmidt wrote:
> Trap numbers can have extra bits at the bottom that need to
> be filtered out. There are a few cases where we don't do that.
> 
> It's possible that we got lucky but better safe than sorry.
> 
> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Applied to powerpc next, thanks.

https://git.kernel.org/powerpc/c/2271db20e4b362405bacc0e4095df4

cheers