[PATCH 1/3][For 4.19/4.14] spi: spi-fsl-spi: automatically adapt bits-per-word in cpu mode

[PATCH 1/3][For 4.19/4.14] spi: spi-fsl-spi: automatically adapt bits-per-word in cpu mode

[Christophe Leroy]

From: Rasmus Villemoes <rasmus.villemoes@prevas.dk>

(cherry picked from upstream af0e6242909c3c4297392ca3e94eff1b4db71a97)

Taking one interrupt for every byte is rather slow. Since the
controller is perfectly capable of transmitting 32 bits at a time,
change t->bits_per-word to 32 when the length is divisible by 4 and
large enough that the reduced number of interrupts easily compensates
for the one or two extra fsl_spi_setup_transfer() calls this causes.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
---
 drivers/spi/spi-fsl-spi.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/drivers/spi/spi-fsl-spi.c b/drivers/spi/spi-fsl-spi.c
index 479d10dc6cb8..946b417f2d1c 100644
--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -357,12 +357,28 @@ static int fsl_spi_bufs(struct spi_device *spi, struct spi_transfer *t,
 static int fsl_spi_do_one_msg(struct spi_master *master,
 			      struct spi_message *m)
 {
+	struct mpc8xxx_spi *mpc8xxx_spi = spi_master_get_devdata(master);
 	struct spi_device *spi = m->spi;
 	struct spi_transfer *t, *first;
 	unsigned int cs_change;
 	const int nsecs = 50;
 	int status;
 
+	/*
+	 * In CPU mode, optimize large byte transfers to use larger
+	 * bits_per_word values to reduce number of interrupts taken.
+	 */
+	if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
+		list_for_each_entry(t, &m->transfers, transfer_list) {
+			if (t->len < 256 || t->bits_per_word != 8)
+				continue;
+			if ((t->len & 3) == 0)
+				t->bits_per_word = 32;
+			else if ((t->len & 1) == 0)
+				t->bits_per_word = 16;
+		}
+	}
+
 	/* Don't allow changes if CS is active */
 	first = list_first_entry(&m->transfers, struct spi_transfer,
 			transfer_list);
-- 
2.40.1

[PATCH 2/3][For 4.19/4.14] spi: fsl-spi: Re-organise transfer bits_per_word adaptation

[Christophe Leroy]

(backported from upstream 8a5299a1278eadf1e08a598a5345c376206f171e)

For different reasons, fsl-spi driver performs bits_per_word
modifications for different reasons:
- On CPU mode, to minimise amount of interrupts
- On CPM/QE mode to work around controller byte order

For CPU mode that's done in fsl_spi_prepare_message() while
for CPM mode that's done in fsl_spi_setup_transfer().

Reunify all of it in fsl_spi_prepare_message(), and catch
impossible cases early through master's bits_per_word_mask
instead of returning EINVAL later.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/0ce96fe96e8b07cba0613e4097cfd94d09b8919a.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 drivers/spi/spi-fsl-spi.c | 50 ++++++++++++++++++---------------------
 1 file changed, 23 insertions(+), 27 deletions(-)

diff --git a/drivers/spi/spi-fsl-spi.c b/drivers/spi/spi-fsl-spi.c
index 946b417f2d1c..e08a11070c5c 100644
--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -201,26 +201,6 @@ static int mspi_apply_cpu_mode_quirks(struct spi_mpc8xxx_cs *cs,
 	return bits_per_word;
 }
 
-static int mspi_apply_qe_mode_quirks(struct spi_mpc8xxx_cs *cs,
-				struct spi_device *spi,
-				int bits_per_word)
-{
-	/* CPM/QE uses Little Endian for words > 8
-	 * so transform 16 and 32 bits words into 8 bits
-	 * Unfortnatly that doesn't work for LSB so
-	 * reject these for now */
-	/* Note: 32 bits word, LSB works iff
-	 * tfcr/rfcr is set to CPMFCR_GBL */
-	if (spi->mode & SPI_LSB_FIRST &&
-	    bits_per_word > 8)
-		return -EINVAL;
-	if (bits_per_word <= 8)
-		return bits_per_word;
-	if (bits_per_word == 16 || bits_per_word == 32)
-		return 8; /* pretend its 8 bits */
-	return -EINVAL;
-}
-
 static int fsl_spi_setup_transfer(struct spi_device *spi,
 					struct spi_transfer *t)
 {
@@ -248,9 +228,6 @@ static int fsl_spi_setup_transfer(struct spi_device *spi,
 		bits_per_word = mspi_apply_cpu_mode_quirks(cs, spi,
 							   mpc8xxx_spi,
 							   bits_per_word);
-	else
-		bits_per_word = mspi_apply_qe_mode_quirks(cs, spi,
-							  bits_per_word);
 
 	if (bits_per_word < 0)
 		return bits_per_word;
@@ -368,14 +345,27 @@ static int fsl_spi_do_one_msg(struct spi_master *master,
 	 * In CPU mode, optimize large byte transfers to use larger
 	 * bits_per_word values to reduce number of interrupts taken.
 	 */
-	if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
-		list_for_each_entry(t, &m->transfers, transfer_list) {
+	list_for_each_entry(t, &m->transfers, transfer_list) {
+		if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
 			if (t->len < 256 || t->bits_per_word != 8)
 				continue;
 			if ((t->len & 3) == 0)
 				t->bits_per_word = 32;
 			else if ((t->len & 1) == 0)
 				t->bits_per_word = 16;
+		} else {
+			/*
+			 * CPM/QE uses Little Endian for words > 8
+			 * so transform 16 and 32 bits words into 8 bits
+			 * Unfortnatly that doesn't work for LSB so
+			 * reject these for now
+			 * Note: 32 bits word, LSB works iff
+			 * tfcr/rfcr is set to CPMFCR_GBL
+			 */
+			if (m->spi->mode & SPI_LSB_FIRST && t->bits_per_word > 8)
+				return -EINVAL;
+			if (t->bits_per_word == 16 || t->bits_per_word == 32)
+				t->bits_per_word = 8; /* pretend its 8 bits */
 		}
 	}
 
@@ -658,8 +648,14 @@ static struct spi_master * fsl_spi_probe(struct device *dev,
 	if (mpc8xxx_spi->type == TYPE_GRLIB)
 		fsl_spi_grlib_probe(dev);
 
-	master->bits_per_word_mask =
-		(SPI_BPW_RANGE_MASK(4, 16) | SPI_BPW_MASK(32)) &
+	if (mpc8xxx_spi->flags & SPI_CPM_MODE)
+		master->bits_per_word_mask =
+			(SPI_BPW_RANGE_MASK(4, 8) | SPI_BPW_MASK(16) | SPI_BPW_MASK(32));
+	else
+		master->bits_per_word_mask =
+			(SPI_BPW_RANGE_MASK(4, 16) | SPI_BPW_MASK(32));
+
+	master->bits_per_word_mask &=
 		SPI_BPW_RANGE_MASK(1, mpc8xxx_spi->max_bits_per_word);
 
 	if (mpc8xxx_spi->flags & SPI_QE_CPU_MODE)
-- 
2.40.1

[PATCH 3/3][For 4.19/4.14] spi: fsl-cpm: Use 16 bit mode for large transfers with even size

[Christophe Leroy]

(cherry picked from upstream fc96ec826bced75cc6b9c07a4ac44bbf651337ab)

On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped as seen in a previous commit.

So, for large tranfers with an even size, allocate a temporary tx
buffer and byte-swap data before and after transfer.

This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.

For the time being, only do it on CPM1 as there must be a
trade-off between the CPM load reduction and the CPU load required
to byte swap the data.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f2e981f20f92dd28983c3949702a09248c23845c.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 drivers/spi/spi-fsl-cpm.c | 23 +++++++++++++++++++++++
 drivers/spi/spi-fsl-spi.c |  3 +++
 2 files changed, 26 insertions(+)

diff --git a/drivers/spi/spi-fsl-cpm.c b/drivers/spi/spi-fsl-cpm.c
index 8f7b26ec181e..0485593dc2f5 100644
--- a/drivers/spi/spi-fsl-cpm.c
+++ b/drivers/spi/spi-fsl-cpm.c
@@ -25,6 +25,7 @@
 #include <linux/spi/spi.h>
 #include <linux/types.h>
 #include <linux/platform_device.h>
+#include <linux/byteorder/generic.h>
 
 #include "spi-fsl-cpm.h"
 #include "spi-fsl-lib.h"
@@ -124,6 +125,21 @@ int fsl_spi_cpm_bufs(struct mpc8xxx_spi *mspi,
 		mspi->rx_dma = mspi->dma_dummy_rx;
 		mspi->map_rx_dma = 0;
 	}
+	if (t->bits_per_word == 16 && t->tx_buf) {
+		const u16 *src = t->tx_buf;
+		u16 *dst;
+		int i;
+
+		dst = kmalloc(t->len, GFP_KERNEL);
+		if (!dst)
+			return -ENOMEM;
+
+		for (i = 0; i < t->len >> 1; i++)
+			dst[i] = cpu_to_le16p(src + i);
+
+		mspi->tx = dst;
+		mspi->map_tx_dma = 1;
+	}
 
 	if (mspi->map_tx_dma) {
 		void *nonconst_tx = (void *)mspi->tx; /* shut up gcc */
@@ -177,6 +193,13 @@ void fsl_spi_cpm_bufs_complete(struct mpc8xxx_spi *mspi)
 	if (mspi->map_rx_dma)
 		dma_unmap_single(dev, mspi->rx_dma, t->len, DMA_FROM_DEVICE);
 	mspi->xfer_in_progress = NULL;
+
+	if (t->bits_per_word == 16 && t->rx_buf) {
+		int i;
+
+		for (i = 0; i < t->len; i += 2)
+			le16_to_cpus(t->rx_buf + i);
+	}
 }
 EXPORT_SYMBOL_GPL(fsl_spi_cpm_bufs_complete);
 
diff --git a/drivers/spi/spi-fsl-spi.c b/drivers/spi/spi-fsl-spi.c
index e08a11070c5c..5e49fed487f8 100644
--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -366,6 +366,9 @@ static int fsl_spi_do_one_msg(struct spi_master *master,
 				return -EINVAL;
 			if (t->bits_per_word == 16 || t->bits_per_word == 32)
 				t->bits_per_word = 8; /* pretend its 8 bits */
+			if (t->bits_per_word == 8 && t->len >= 256 &&
+			    (mpc8xxx_spi->flags & SPI_CPM1))
+				t->bits_per_word = 16;
 		}
 	}
 
-- 
2.40.1

[PATCH 1/2][For 5.15/5.10/5.4] spi: fsl-spi: Re-organise transfer bits_per_word adaptation

[Christophe Leroy]

(backported from upstream 8a5299a1278eadf1e08a598a5345c376206f171e)

For different reasons, fsl-spi driver performs bits_per_word
modifications for different reasons:
- On CPU mode, to minimise amount of interrupts
- On CPM/QE mode to work around controller byte order

For CPU mode that's done in fsl_spi_prepare_message() while
for CPM mode that's done in fsl_spi_setup_transfer().

Reunify all of it in fsl_spi_prepare_message(), and catch
impossible cases early through master's bits_per_word_mask
instead of returning EINVAL later.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/0ce96fe96e8b07cba0613e4097cfd94d09b8919a.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 drivers/spi/spi-fsl-spi.c | 50 ++++++++++++++++++---------------------
 1 file changed, 23 insertions(+), 27 deletions(-)

diff --git a/drivers/spi/spi-fsl-spi.c b/drivers/spi/spi-fsl-spi.c
index 1bad0ceac81b..f1d4aa310233 100644
--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -203,26 +203,6 @@ static int mspi_apply_cpu_mode_quirks(struct spi_mpc8xxx_cs *cs,
 	return bits_per_word;
 }
 
-static int mspi_apply_qe_mode_quirks(struct spi_mpc8xxx_cs *cs,
-				struct spi_device *spi,
-				int bits_per_word)
-{
-	/* CPM/QE uses Little Endian for words > 8
-	 * so transform 16 and 32 bits words into 8 bits
-	 * Unfortnatly that doesn't work for LSB so
-	 * reject these for now */
-	/* Note: 32 bits word, LSB works iff
-	 * tfcr/rfcr is set to CPMFCR_GBL */
-	if (spi->mode & SPI_LSB_FIRST &&
-	    bits_per_word > 8)
-		return -EINVAL;
-	if (bits_per_word <= 8)
-		return bits_per_word;
-	if (bits_per_word == 16 || bits_per_word == 32)
-		return 8; /* pretend its 8 bits */
-	return -EINVAL;
-}
-
 static int fsl_spi_setup_transfer(struct spi_device *spi,
 					struct spi_transfer *t)
 {
@@ -250,9 +230,6 @@ static int fsl_spi_setup_transfer(struct spi_device *spi,
 		bits_per_word = mspi_apply_cpu_mode_quirks(cs, spi,
 							   mpc8xxx_spi,
 							   bits_per_word);
-	else
-		bits_per_word = mspi_apply_qe_mode_quirks(cs, spi,
-							  bits_per_word);
 
 	if (bits_per_word < 0)
 		return bits_per_word;
@@ -370,14 +347,27 @@ static int fsl_spi_do_one_msg(struct spi_master *master,
 	 * In CPU mode, optimize large byte transfers to use larger
 	 * bits_per_word values to reduce number of interrupts taken.
 	 */
-	if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
-		list_for_each_entry(t, &m->transfers, transfer_list) {
+	list_for_each_entry(t, &m->transfers, transfer_list) {
+		if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
 			if (t->len < 256 || t->bits_per_word != 8)
 				continue;
 			if ((t->len & 3) == 0)
 				t->bits_per_word = 32;
 			else if ((t->len & 1) == 0)
 				t->bits_per_word = 16;
+		} else {
+			/*
+			 * CPM/QE uses Little Endian for words > 8
+			 * so transform 16 and 32 bits words into 8 bits
+			 * Unfortnatly that doesn't work for LSB so
+			 * reject these for now
+			 * Note: 32 bits word, LSB works iff
+			 * tfcr/rfcr is set to CPMFCR_GBL
+			 */
+			if (m->spi->mode & SPI_LSB_FIRST && t->bits_per_word > 8)
+				return -EINVAL;
+			if (t->bits_per_word == 16 || t->bits_per_word == 32)
+				t->bits_per_word = 8; /* pretend its 8 bits */
 		}
 	}
 
@@ -635,8 +625,14 @@ static struct spi_master *fsl_spi_probe(struct device *dev,
 	if (mpc8xxx_spi->type == TYPE_GRLIB)
 		fsl_spi_grlib_probe(dev);
 
-	master->bits_per_word_mask =
-		(SPI_BPW_RANGE_MASK(4, 16) | SPI_BPW_MASK(32)) &
+	if (mpc8xxx_spi->flags & SPI_CPM_MODE)
+		master->bits_per_word_mask =
+			(SPI_BPW_RANGE_MASK(4, 8) | SPI_BPW_MASK(16) | SPI_BPW_MASK(32));
+	else
+		master->bits_per_word_mask =
+			(SPI_BPW_RANGE_MASK(4, 16) | SPI_BPW_MASK(32));
+
+	master->bits_per_word_mask &=
 		SPI_BPW_RANGE_MASK(1, mpc8xxx_spi->max_bits_per_word);
 
 	if (mpc8xxx_spi->flags & SPI_QE_CPU_MODE)
-- 
2.40.1

[PATCH 2/2][For 5.15/5.10/5.4] spi: fsl-cpm: Use 16 bit mode for large transfers with even size

[Christophe Leroy]

(cherry picked from upstream fc96ec826bced75cc6b9c07a4ac44bbf651337ab)

On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped as seen in a previous commit.

So, for large tranfers with an even size, allocate a temporary tx
buffer and byte-swap data before and after transfer.

This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.

For the time being, only do it on CPM1 as there must be a
trade-off between the CPM load reduction and the CPU load required
to byte swap the data.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f2e981f20f92dd28983c3949702a09248c23845c.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 drivers/spi/spi-fsl-cpm.c | 23 +++++++++++++++++++++++
 drivers/spi/spi-fsl-spi.c |  3 +++
 2 files changed, 26 insertions(+)

diff --git a/drivers/spi/spi-fsl-cpm.c b/drivers/spi/spi-fsl-cpm.c
index ee905880769e..7832ce330b29 100644
--- a/drivers/spi/spi-fsl-cpm.c
+++ b/drivers/spi/spi-fsl-cpm.c
@@ -21,6 +21,7 @@
 #include <linux/spi/spi.h>
 #include <linux/types.h>
 #include <linux/platform_device.h>
+#include <linux/byteorder/generic.h>
 
 #include "spi-fsl-cpm.h"
 #include "spi-fsl-lib.h"
@@ -120,6 +121,21 @@ int fsl_spi_cpm_bufs(struct mpc8xxx_spi *mspi,
 		mspi->rx_dma = mspi->dma_dummy_rx;
 		mspi->map_rx_dma = 0;
 	}
+	if (t->bits_per_word == 16 && t->tx_buf) {
+		const u16 *src = t->tx_buf;
+		u16 *dst;
+		int i;
+
+		dst = kmalloc(t->len, GFP_KERNEL);
+		if (!dst)
+			return -ENOMEM;
+
+		for (i = 0; i < t->len >> 1; i++)
+			dst[i] = cpu_to_le16p(src + i);
+
+		mspi->tx = dst;
+		mspi->map_tx_dma = 1;
+	}
 
 	if (mspi->map_tx_dma) {
 		void *nonconst_tx = (void *)mspi->tx; /* shut up gcc */
@@ -173,6 +189,13 @@ void fsl_spi_cpm_bufs_complete(struct mpc8xxx_spi *mspi)
 	if (mspi->map_rx_dma)
 		dma_unmap_single(dev, mspi->rx_dma, t->len, DMA_FROM_DEVICE);
 	mspi->xfer_in_progress = NULL;
+
+	if (t->bits_per_word == 16 && t->rx_buf) {
+		int i;
+
+		for (i = 0; i < t->len; i += 2)
+			le16_to_cpus(t->rx_buf + i);
+	}
 }
 EXPORT_SYMBOL_GPL(fsl_spi_cpm_bufs_complete);
 
diff --git a/drivers/spi/spi-fsl-spi.c b/drivers/spi/spi-fsl-spi.c
index f1d4aa310233..63302e21e574 100644
--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -368,6 +368,9 @@ static int fsl_spi_do_one_msg(struct spi_master *master,
 				return -EINVAL;
 			if (t->bits_per_word == 16 || t->bits_per_word == 32)
 				t->bits_per_word = 8; /* pretend its 8 bits */
+			if (t->bits_per_word == 8 && t->len >= 256 &&
+			    (mpc8xxx_spi->flags & SPI_CPM1))
+				t->bits_per_word = 16;
 		}
 	}
 
-- 
2.40.1

Patch "Subject:[For 4.19/4.14] spi: fsl-cpm: Use 16 bit mode for large transfers with even size" has been added to the 4.14-stable tree

[gregkh]

This is a note to let you know that I've just added the patch titled

    Subject:[For 4.19/4.14] spi: fsl-cpm: Use 16 bit mode for large transfers with even size

to the 4.14-stable tree which can be found at:
    http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     spi-fsl-cpm-use-16-bit-mode-for-large-transfers-with-even-size.patch
and it can be found in the queue-4.14 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@vger.kernel.org> know about it.


From christophe.leroy@csgroup.eu Mon May 15 15:07:58 2023
From: Christophe Leroy <christophe.leroy@csgroup.eu>
Date: Mon, 15 May 2023 16:07:15 +0200
Subject:[For 4.19/4.14] spi: fsl-cpm: Use 16 bit mode for large transfers with even size
To: gregkh@linuxfoundation.org, stable@vger.kernel.org
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>, linux-kernel@vger.kernel.org, linuxppc-dev@lists.ozlabs.org, Mark Brown <broonie@kernel.org>
Message-ID: <9363da33f54e9862b4b59c0ed97924ca7265f7a4.1684158520.git.christophe.leroy@csgroup.eu>

From: Christophe Leroy <christophe.leroy@csgroup.eu>

(cherry picked from upstream fc96ec826bced75cc6b9c07a4ac44bbf651337ab)

On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped as seen in a previous commit.

So, for large tranfers with an even size, allocate a temporary tx
buffer and byte-swap data before and after transfer.

This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.

For the time being, only do it on CPM1 as there must be a
trade-off between the CPM load reduction and the CPU load required
to byte swap the data.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f2e981f20f92dd28983c3949702a09248c23845c.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/spi/spi-fsl-cpm.c |   23 +++++++++++++++++++++++
 drivers/spi/spi-fsl-spi.c |    3 +++
 2 files changed, 26 insertions(+)

--- a/drivers/spi/spi-fsl-cpm.c
+++ b/drivers/spi/spi-fsl-cpm.c
@@ -25,6 +25,7 @@
 #include <linux/spi/spi.h>
 #include <linux/types.h>
 #include <linux/platform_device.h>
+#include <linux/byteorder/generic.h>
 
 #include "spi-fsl-cpm.h"
 #include "spi-fsl-lib.h"
@@ -124,6 +125,21 @@ int fsl_spi_cpm_bufs(struct mpc8xxx_spi
 		mspi->rx_dma = mspi->dma_dummy_rx;
 		mspi->map_rx_dma = 0;
 	}
+	if (t->bits_per_word == 16 && t->tx_buf) {
+		const u16 *src = t->tx_buf;
+		u16 *dst;
+		int i;
+
+		dst = kmalloc(t->len, GFP_KERNEL);
+		if (!dst)
+			return -ENOMEM;
+
+		for (i = 0; i < t->len >> 1; i++)
+			dst[i] = cpu_to_le16p(src + i);
+
+		mspi->tx = dst;
+		mspi->map_tx_dma = 1;
+	}
 
 	if (mspi->map_tx_dma) {
 		void *nonconst_tx = (void *)mspi->tx; /* shut up gcc */
@@ -177,6 +193,13 @@ void fsl_spi_cpm_bufs_complete(struct mp
 	if (mspi->map_rx_dma)
 		dma_unmap_single(dev, mspi->rx_dma, t->len, DMA_FROM_DEVICE);
 	mspi->xfer_in_progress = NULL;
+
+	if (t->bits_per_word == 16 && t->rx_buf) {
+		int i;
+
+		for (i = 0; i < t->len; i += 2)
+			le16_to_cpus(t->rx_buf + i);
+	}
 }
 EXPORT_SYMBOL_GPL(fsl_spi_cpm_bufs_complete);
 
--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -366,6 +366,9 @@ static int fsl_spi_do_one_msg(struct spi
 				return -EINVAL;
 			if (t->bits_per_word == 16 || t->bits_per_word == 32)
 				t->bits_per_word = 8; /* pretend its 8 bits */
+			if (t->bits_per_word == 8 && t->len >= 256 &&
+			    (mpc8xxx_spi->flags & SPI_CPM1))
+				t->bits_per_word = 16;
 		}
 	}
 


Patches currently in stable-queue which might be from christophe.leroy@csgroup.eu are

queue-4.14/spi-fsl-cpm-use-16-bit-mode-for-large-transfers-with-even-size.patch
queue-4.14/spi-fsl-spi-re-organise-transfer-bits_per_word-adaptation.patch
queue-4.14/spi-spi-fsl-spi-automatically-adapt-bits-per-word-in-cpu-mode.patch

Patch "Subject:[For 4.19/4.14] spi: fsl-spi: Re-organise transfer bits_per_word adaptation" has been added to the 4.14-stable tree

[gregkh]

This is a note to let you know that I've just added the patch titled

    Subject:[For 4.19/4.14] spi: fsl-spi: Re-organise transfer bits_per_word adaptation

to the 4.14-stable tree which can be found at:
    http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     spi-fsl-spi-re-organise-transfer-bits_per_word-adaptation.patch
and it can be found in the queue-4.14 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@vger.kernel.org> know about it.


From christophe.leroy@csgroup.eu Mon May 15 15:08:01 2023
From: Christophe Leroy <christophe.leroy@csgroup.eu>
Date: Mon, 15 May 2023 16:07:14 +0200
Subject:[For 4.19/4.14] spi: fsl-spi: Re-organise transfer bits_per_word adaptation
To: gregkh@linuxfoundation.org, stable@vger.kernel.org
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>, linux-kernel@vger.kernel.org, linuxppc-dev@lists.ozlabs.org, Mark Brown <broonie@kernel.org>
Message-ID: <e105f49ce5da21b48dc0450f5fb3644571ee9c1a.1684158520.git.christophe.leroy@csgroup.eu>

From: Christophe Leroy <christophe.leroy@csgroup.eu>

(backported from upstream 8a5299a1278eadf1e08a598a5345c376206f171e)

For different reasons, fsl-spi driver performs bits_per_word
modifications for different reasons:
- On CPU mode, to minimise amount of interrupts
- On CPM/QE mode to work around controller byte order

For CPU mode that's done in fsl_spi_prepare_message() while
for CPM mode that's done in fsl_spi_setup_transfer().

Reunify all of it in fsl_spi_prepare_message(), and catch
impossible cases early through master's bits_per_word_mask
instead of returning EINVAL later.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/0ce96fe96e8b07cba0613e4097cfd94d09b8919a.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/spi/spi-fsl-spi.c |   50 +++++++++++++++++++++-------------------------
 1 file changed, 23 insertions(+), 27 deletions(-)

--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -201,26 +201,6 @@ static int mspi_apply_cpu_mode_quirks(st
 	return bits_per_word;
 }
 
-static int mspi_apply_qe_mode_quirks(struct spi_mpc8xxx_cs *cs,
-				struct spi_device *spi,
-				int bits_per_word)
-{
-	/* CPM/QE uses Little Endian for words > 8
-	 * so transform 16 and 32 bits words into 8 bits
-	 * Unfortnatly that doesn't work for LSB so
-	 * reject these for now */
-	/* Note: 32 bits word, LSB works iff
-	 * tfcr/rfcr is set to CPMFCR_GBL */
-	if (spi->mode & SPI_LSB_FIRST &&
-	    bits_per_word > 8)
-		return -EINVAL;
-	if (bits_per_word <= 8)
-		return bits_per_word;
-	if (bits_per_word == 16 || bits_per_word == 32)
-		return 8; /* pretend its 8 bits */
-	return -EINVAL;
-}
-
 static int fsl_spi_setup_transfer(struct spi_device *spi,
 					struct spi_transfer *t)
 {
@@ -248,9 +228,6 @@ static int fsl_spi_setup_transfer(struct
 		bits_per_word = mspi_apply_cpu_mode_quirks(cs, spi,
 							   mpc8xxx_spi,
 							   bits_per_word);
-	else
-		bits_per_word = mspi_apply_qe_mode_quirks(cs, spi,
-							  bits_per_word);
 
 	if (bits_per_word < 0)
 		return bits_per_word;
@@ -368,14 +345,27 @@ static int fsl_spi_do_one_msg(struct spi
 	 * In CPU mode, optimize large byte transfers to use larger
 	 * bits_per_word values to reduce number of interrupts taken.
 	 */
-	if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
-		list_for_each_entry(t, &m->transfers, transfer_list) {
+	list_for_each_entry(t, &m->transfers, transfer_list) {
+		if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
 			if (t->len < 256 || t->bits_per_word != 8)
 				continue;
 			if ((t->len & 3) == 0)
 				t->bits_per_word = 32;
 			else if ((t->len & 1) == 0)
 				t->bits_per_word = 16;
+		} else {
+			/*
+			 * CPM/QE uses Little Endian for words > 8
+			 * so transform 16 and 32 bits words into 8 bits
+			 * Unfortnatly that doesn't work for LSB so
+			 * reject these for now
+			 * Note: 32 bits word, LSB works iff
+			 * tfcr/rfcr is set to CPMFCR_GBL
+			 */
+			if (m->spi->mode & SPI_LSB_FIRST && t->bits_per_word > 8)
+				return -EINVAL;
+			if (t->bits_per_word == 16 || t->bits_per_word == 32)
+				t->bits_per_word = 8; /* pretend its 8 bits */
 		}
 	}
 
@@ -658,8 +648,14 @@ static struct spi_master * fsl_spi_probe
 	if (mpc8xxx_spi->type == TYPE_GRLIB)
 		fsl_spi_grlib_probe(dev);
 
-	master->bits_per_word_mask =
-		(SPI_BPW_RANGE_MASK(4, 16) | SPI_BPW_MASK(32)) &
+	if (mpc8xxx_spi->flags & SPI_CPM_MODE)
+		master->bits_per_word_mask =
+			(SPI_BPW_RANGE_MASK(4, 8) | SPI_BPW_MASK(16) | SPI_BPW_MASK(32));
+	else
+		master->bits_per_word_mask =
+			(SPI_BPW_RANGE_MASK(4, 16) | SPI_BPW_MASK(32));
+
+	master->bits_per_word_mask &=
 		SPI_BPW_RANGE_MASK(1, mpc8xxx_spi->max_bits_per_word);
 
 	if (mpc8xxx_spi->flags & SPI_QE_CPU_MODE)


Patches currently in stable-queue which might be from christophe.leroy@csgroup.eu are

queue-4.14/spi-fsl-cpm-use-16-bit-mode-for-large-transfers-with-even-size.patch
queue-4.14/spi-fsl-spi-re-organise-transfer-bits_per_word-adaptation.patch
queue-4.14/spi-spi-fsl-spi-automatically-adapt-bits-per-word-in-cpu-mode.patch

Patch "Subject:[For 4.19/4.14] spi: spi-fsl-spi: automatically adapt bits-per-word in cpu mode" has been added to the 4.14-stable tree

[gregkh]

This is a note to let you know that I've just added the patch titled

    Subject:[For 4.19/4.14] spi: spi-fsl-spi: automatically adapt bits-per-word in cpu mode

to the 4.14-stable tree which can be found at:
    http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     spi-spi-fsl-spi-automatically-adapt-bits-per-word-in-cpu-mode.patch
and it can be found in the queue-4.14 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@vger.kernel.org> know about it.


From christophe.leroy@csgroup.eu Mon May 15 15:08:06 2023
From: Christophe Leroy <christophe.leroy@csgroup.eu>
Date: Mon, 15 May 2023 16:07:13 +0200
Subject:[For 4.19/4.14] spi: spi-fsl-spi: automatically adapt bits-per-word in cpu mode
To: gregkh@linuxfoundation.org, stable@vger.kernel.org
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>, linux-kernel@vger.kernel.org, linuxppc-dev@lists.ozlabs.org, Rasmus Villemoes <rasmus.villemoes@prevas.dk>, Mark Brown <broonie@kernel.org>
Message-ID: <674d9af640acf4aa04abd642cc81de926d3271ed.1684158520.git.christophe.leroy@csgroup.eu>

From: Rasmus Villemoes <rasmus.villemoes@prevas.dk>

(cherry picked from upstream af0e6242909c3c4297392ca3e94eff1b4db71a97)

Taking one interrupt for every byte is rather slow. Since the
controller is perfectly capable of transmitting 32 bits at a time,
change t->bits_per-word to 32 when the length is divisible by 4 and
large enough that the reduced number of interrupts easily compensates
for the one or two extra fsl_spi_setup_transfer() calls this causes.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/spi/spi-fsl-spi.c |   16 ++++++++++++++++
 1 file changed, 16 insertions(+)

--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -357,12 +357,28 @@ static int fsl_spi_bufs(struct spi_devic
 static int fsl_spi_do_one_msg(struct spi_master *master,
 			      struct spi_message *m)
 {
+	struct mpc8xxx_spi *mpc8xxx_spi = spi_master_get_devdata(master);
 	struct spi_device *spi = m->spi;
 	struct spi_transfer *t, *first;
 	unsigned int cs_change;
 	const int nsecs = 50;
 	int status;
 
+	/*
+	 * In CPU mode, optimize large byte transfers to use larger
+	 * bits_per_word values to reduce number of interrupts taken.
+	 */
+	if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
+		list_for_each_entry(t, &m->transfers, transfer_list) {
+			if (t->len < 256 || t->bits_per_word != 8)
+				continue;
+			if ((t->len & 3) == 0)
+				t->bits_per_word = 32;
+			else if ((t->len & 1) == 0)
+				t->bits_per_word = 16;
+		}
+	}
+
 	/* Don't allow changes if CS is active */
 	first = list_first_entry(&m->transfers, struct spi_transfer,
 			transfer_list);


Patches currently in stable-queue which might be from christophe.leroy@csgroup.eu are

queue-4.14/spi-fsl-cpm-use-16-bit-mode-for-large-transfers-with-even-size.patch
queue-4.14/spi-fsl-spi-re-organise-transfer-bits_per_word-adaptation.patch
queue-4.14/spi-spi-fsl-spi-automatically-adapt-bits-per-word-in-cpu-mode.patch

Patch "Subject:[For 4.19/4.14] spi: fsl-cpm: Use 16 bit mode for large transfers with even size" has been added to the 4.19-stable tree

[gregkh]

This is a note to let you know that I've just added the patch titled

    Subject:[For 4.19/4.14] spi: fsl-cpm: Use 16 bit mode for large transfers with even size

to the 4.19-stable tree which can be found at:
    http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     spi-fsl-cpm-use-16-bit-mode-for-large-transfers-with-even-size.patch
and it can be found in the queue-4.19 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@vger.kernel.org> know about it.


From christophe.leroy@csgroup.eu Mon May 15 15:07:58 2023
From: Christophe Leroy <christophe.leroy@csgroup.eu>
Date: Mon, 15 May 2023 16:07:15 +0200
Subject:[For 4.19/4.14] spi: fsl-cpm: Use 16 bit mode for large transfers with even size
To: gregkh@linuxfoundation.org, stable@vger.kernel.org
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>, linux-kernel@vger.kernel.org, linuxppc-dev@lists.ozlabs.org, Mark Brown <broonie@kernel.org>
Message-ID: <9363da33f54e9862b4b59c0ed97924ca7265f7a4.1684158520.git.christophe.leroy@csgroup.eu>

From: Christophe Leroy <christophe.leroy@csgroup.eu>

(cherry picked from upstream fc96ec826bced75cc6b9c07a4ac44bbf651337ab)

On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped as seen in a previous commit.

So, for large tranfers with an even size, allocate a temporary tx
buffer and byte-swap data before and after transfer.

This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.

For the time being, only do it on CPM1 as there must be a
trade-off between the CPM load reduction and the CPU load required
to byte swap the data.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f2e981f20f92dd28983c3949702a09248c23845c.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/spi/spi-fsl-cpm.c |   23 +++++++++++++++++++++++
 drivers/spi/spi-fsl-spi.c |    3 +++
 2 files changed, 26 insertions(+)

--- a/drivers/spi/spi-fsl-cpm.c
+++ b/drivers/spi/spi-fsl-cpm.c
@@ -25,6 +25,7 @@
 #include <linux/spi/spi.h>
 #include <linux/types.h>
 #include <linux/platform_device.h>
+#include <linux/byteorder/generic.h>
 
 #include "spi-fsl-cpm.h"
 #include "spi-fsl-lib.h"
@@ -124,6 +125,21 @@ int fsl_spi_cpm_bufs(struct mpc8xxx_spi
 		mspi->rx_dma = mspi->dma_dummy_rx;
 		mspi->map_rx_dma = 0;
 	}
+	if (t->bits_per_word == 16 && t->tx_buf) {
+		const u16 *src = t->tx_buf;
+		u16 *dst;
+		int i;
+
+		dst = kmalloc(t->len, GFP_KERNEL);
+		if (!dst)
+			return -ENOMEM;
+
+		for (i = 0; i < t->len >> 1; i++)
+			dst[i] = cpu_to_le16p(src + i);
+
+		mspi->tx = dst;
+		mspi->map_tx_dma = 1;
+	}
 
 	if (mspi->map_tx_dma) {
 		void *nonconst_tx = (void *)mspi->tx; /* shut up gcc */
@@ -177,6 +193,13 @@ void fsl_spi_cpm_bufs_complete(struct mp
 	if (mspi->map_rx_dma)
 		dma_unmap_single(dev, mspi->rx_dma, t->len, DMA_FROM_DEVICE);
 	mspi->xfer_in_progress = NULL;
+
+	if (t->bits_per_word == 16 && t->rx_buf) {
+		int i;
+
+		for (i = 0; i < t->len; i += 2)
+			le16_to_cpus(t->rx_buf + i);
+	}
 }
 EXPORT_SYMBOL_GPL(fsl_spi_cpm_bufs_complete);
 
--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -366,6 +366,9 @@ static int fsl_spi_do_one_msg(struct spi
 				return -EINVAL;
 			if (t->bits_per_word == 16 || t->bits_per_word == 32)
 				t->bits_per_word = 8; /* pretend its 8 bits */
+			if (t->bits_per_word == 8 && t->len >= 256 &&
+			    (mpc8xxx_spi->flags & SPI_CPM1))
+				t->bits_per_word = 16;
 		}
 	}
 


Patches currently in stable-queue which might be from christophe.leroy@csgroup.eu are

queue-4.19/spi-fsl-cpm-use-16-bit-mode-for-large-transfers-with-even-size.patch
queue-4.19/spi-fsl-spi-re-organise-transfer-bits_per_word-adaptation.patch
queue-4.19/spi-spi-fsl-spi-automatically-adapt-bits-per-word-in-cpu-mode.patch

Patch "Subject:[For 4.19/4.14] spi: fsl-spi: Re-organise transfer bits_per_word adaptation" has been added to the 4.19-stable tree

[gregkh]

This is a note to let you know that I've just added the patch titled

    Subject:[For 4.19/4.14] spi: fsl-spi: Re-organise transfer bits_per_word adaptation

to the 4.19-stable tree which can be found at:
    http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     spi-fsl-spi-re-organise-transfer-bits_per_word-adaptation.patch
and it can be found in the queue-4.19 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@vger.kernel.org> know about it.


From christophe.leroy@csgroup.eu Mon May 15 15:08:01 2023
From: Christophe Leroy <christophe.leroy@csgroup.eu>
Date: Mon, 15 May 2023 16:07:14 +0200
Subject:[For 4.19/4.14] spi: fsl-spi: Re-organise transfer bits_per_word adaptation
To: gregkh@linuxfoundation.org, stable@vger.kernel.org
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>, linux-kernel@vger.kernel.org, linuxppc-dev@lists.ozlabs.org, Mark Brown <broonie@kernel.org>
Message-ID: <e105f49ce5da21b48dc0450f5fb3644571ee9c1a.1684158520.git.christophe.leroy@csgroup.eu>

From: Christophe Leroy <christophe.leroy@csgroup.eu>

(backported from upstream 8a5299a1278eadf1e08a598a5345c376206f171e)

For different reasons, fsl-spi driver performs bits_per_word
modifications for different reasons:
- On CPU mode, to minimise amount of interrupts
- On CPM/QE mode to work around controller byte order

For CPU mode that's done in fsl_spi_prepare_message() while
for CPM mode that's done in fsl_spi_setup_transfer().

Reunify all of it in fsl_spi_prepare_message(), and catch
impossible cases early through master's bits_per_word_mask
instead of returning EINVAL later.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/0ce96fe96e8b07cba0613e4097cfd94d09b8919a.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/spi/spi-fsl-spi.c |   50 +++++++++++++++++++++-------------------------
 1 file changed, 23 insertions(+), 27 deletions(-)

--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -201,26 +201,6 @@ static int mspi_apply_cpu_mode_quirks(st
 	return bits_per_word;
 }
 
-static int mspi_apply_qe_mode_quirks(struct spi_mpc8xxx_cs *cs,
-				struct spi_device *spi,
-				int bits_per_word)
-{
-	/* CPM/QE uses Little Endian for words > 8
-	 * so transform 16 and 32 bits words into 8 bits
-	 * Unfortnatly that doesn't work for LSB so
-	 * reject these for now */
-	/* Note: 32 bits word, LSB works iff
-	 * tfcr/rfcr is set to CPMFCR_GBL */
-	if (spi->mode & SPI_LSB_FIRST &&
-	    bits_per_word > 8)
-		return -EINVAL;
-	if (bits_per_word <= 8)
-		return bits_per_word;
-	if (bits_per_word == 16 || bits_per_word == 32)
-		return 8; /* pretend its 8 bits */
-	return -EINVAL;
-}
-
 static int fsl_spi_setup_transfer(struct spi_device *spi,
 					struct spi_transfer *t)
 {
@@ -248,9 +228,6 @@ static int fsl_spi_setup_transfer(struct
 		bits_per_word = mspi_apply_cpu_mode_quirks(cs, spi,
 							   mpc8xxx_spi,
 							   bits_per_word);
-	else
-		bits_per_word = mspi_apply_qe_mode_quirks(cs, spi,
-							  bits_per_word);
 
 	if (bits_per_word < 0)
 		return bits_per_word;
@@ -368,14 +345,27 @@ static int fsl_spi_do_one_msg(struct spi
 	 * In CPU mode, optimize large byte transfers to use larger
 	 * bits_per_word values to reduce number of interrupts taken.
 	 */
-	if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
-		list_for_each_entry(t, &m->transfers, transfer_list) {
+	list_for_each_entry(t, &m->transfers, transfer_list) {
+		if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
 			if (t->len < 256 || t->bits_per_word != 8)
 				continue;
 			if ((t->len & 3) == 0)
 				t->bits_per_word = 32;
 			else if ((t->len & 1) == 0)
 				t->bits_per_word = 16;
+		} else {
+			/*
+			 * CPM/QE uses Little Endian for words > 8
+			 * so transform 16 and 32 bits words into 8 bits
+			 * Unfortnatly that doesn't work for LSB so
+			 * reject these for now
+			 * Note: 32 bits word, LSB works iff
+			 * tfcr/rfcr is set to CPMFCR_GBL
+			 */
+			if (m->spi->mode & SPI_LSB_FIRST && t->bits_per_word > 8)
+				return -EINVAL;
+			if (t->bits_per_word == 16 || t->bits_per_word == 32)
+				t->bits_per_word = 8; /* pretend its 8 bits */
 		}
 	}
 
@@ -658,8 +648,14 @@ static struct spi_master * fsl_spi_probe
 	if (mpc8xxx_spi->type == TYPE_GRLIB)
 		fsl_spi_grlib_probe(dev);
 
-	master->bits_per_word_mask =
-		(SPI_BPW_RANGE_MASK(4, 16) | SPI_BPW_MASK(32)) &
+	if (mpc8xxx_spi->flags & SPI_CPM_MODE)
+		master->bits_per_word_mask =
+			(SPI_BPW_RANGE_MASK(4, 8) | SPI_BPW_MASK(16) | SPI_BPW_MASK(32));
+	else
+		master->bits_per_word_mask =
+			(SPI_BPW_RANGE_MASK(4, 16) | SPI_BPW_MASK(32));
+
+	master->bits_per_word_mask &=
 		SPI_BPW_RANGE_MASK(1, mpc8xxx_spi->max_bits_per_word);
 
 	if (mpc8xxx_spi->flags & SPI_QE_CPU_MODE)


Patches currently in stable-queue which might be from christophe.leroy@csgroup.eu are

queue-4.19/spi-fsl-cpm-use-16-bit-mode-for-large-transfers-with-even-size.patch
queue-4.19/spi-fsl-spi-re-organise-transfer-bits_per_word-adaptation.patch
queue-4.19/spi-spi-fsl-spi-automatically-adapt-bits-per-word-in-cpu-mode.patch

Patch "Subject:[For 4.19/4.14] spi: spi-fsl-spi: automatically adapt bits-per-word in cpu mode" has been added to the 4.19-stable tree

[gregkh]

This is a note to let you know that I've just added the patch titled

    Subject:[For 4.19/4.14] spi: spi-fsl-spi: automatically adapt bits-per-word in cpu mode

to the 4.19-stable tree which can be found at:
    http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     spi-spi-fsl-spi-automatically-adapt-bits-per-word-in-cpu-mode.patch
and it can be found in the queue-4.19 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@vger.kernel.org> know about it.


From christophe.leroy@csgroup.eu Mon May 15 15:08:06 2023
From: Christophe Leroy <christophe.leroy@csgroup.eu>
Date: Mon, 15 May 2023 16:07:13 +0200
Subject:[For 4.19/4.14] spi: spi-fsl-spi: automatically adapt bits-per-word in cpu mode
To: gregkh@linuxfoundation.org, stable@vger.kernel.org
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>, linux-kernel@vger.kernel.org, linuxppc-dev@lists.ozlabs.org, Rasmus Villemoes <rasmus.villemoes@prevas.dk>, Mark Brown <broonie@kernel.org>
Message-ID: <674d9af640acf4aa04abd642cc81de926d3271ed.1684158520.git.christophe.leroy@csgroup.eu>

From: Rasmus Villemoes <rasmus.villemoes@prevas.dk>

(cherry picked from upstream af0e6242909c3c4297392ca3e94eff1b4db71a97)

Taking one interrupt for every byte is rather slow. Since the
controller is perfectly capable of transmitting 32 bits at a time,
change t->bits_per-word to 32 when the length is divisible by 4 and
large enough that the reduced number of interrupts easily compensates
for the one or two extra fsl_spi_setup_transfer() calls this causes.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/spi/spi-fsl-spi.c |   16 ++++++++++++++++
 1 file changed, 16 insertions(+)

--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -357,12 +357,28 @@ static int fsl_spi_bufs(struct spi_devic
 static int fsl_spi_do_one_msg(struct spi_master *master,
 			      struct spi_message *m)
 {
+	struct mpc8xxx_spi *mpc8xxx_spi = spi_master_get_devdata(master);
 	struct spi_device *spi = m->spi;
 	struct spi_transfer *t, *first;
 	unsigned int cs_change;
 	const int nsecs = 50;
 	int status;
 
+	/*
+	 * In CPU mode, optimize large byte transfers to use larger
+	 * bits_per_word values to reduce number of interrupts taken.
+	 */
+	if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
+		list_for_each_entry(t, &m->transfers, transfer_list) {
+			if (t->len < 256 || t->bits_per_word != 8)
+				continue;
+			if ((t->len & 3) == 0)
+				t->bits_per_word = 32;
+			else if ((t->len & 1) == 0)
+				t->bits_per_word = 16;
+		}
+	}
+
 	/* Don't allow changes if CS is active */
 	first = list_first_entry(&m->transfers, struct spi_transfer,
 			transfer_list);


Patches currently in stable-queue which might be from christophe.leroy@csgroup.eu are

queue-4.19/spi-fsl-cpm-use-16-bit-mode-for-large-transfers-with-even-size.patch
queue-4.19/spi-fsl-spi-re-organise-transfer-bits_per_word-adaptation.patch
queue-4.19/spi-spi-fsl-spi-automatically-adapt-bits-per-word-in-cpu-mode.patch

Patch "Subject:[For 5.15/5.10/5.4] spi: fsl-cpm: Use 16 bit mode for large transfers with even size" has been added to the 5.10-stable tree

[gregkh]

This is a note to let you know that I've just added the patch titled

    Subject:[For 5.15/5.10/5.4] spi: fsl-cpm: Use 16 bit mode for large transfers with even size

to the 5.10-stable tree which can be found at:
    http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     spi-fsl-cpm-use-16-bit-mode-for-large-transfers-with-even-size.patch
and it can be found in the queue-5.10 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@vger.kernel.org> know about it.


From christophe.leroy@csgroup.eu Mon May 15 15:07:59 2023
From: Christophe Leroy <christophe.leroy@csgroup.eu>
Date: Mon, 15 May 2023 16:07:17 +0200
Subject:[For 5.15/5.10/5.4] spi: fsl-cpm: Use 16 bit mode for large transfers with even size
To: gregkh@linuxfoundation.org, stable@vger.kernel.org
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>, linux-kernel@vger.kernel.org, linuxppc-dev@lists.ozlabs.org, Mark Brown <broonie@kernel.org>
Message-ID: <3a1b8774ad7004acb594fbf220f98488dbaa2896.1684156552.git.christophe.leroy@csgroup.eu>

From: Christophe Leroy <christophe.leroy@csgroup.eu>

(cherry picked from upstream fc96ec826bced75cc6b9c07a4ac44bbf651337ab)

On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped as seen in a previous commit.

So, for large tranfers with an even size, allocate a temporary tx
buffer and byte-swap data before and after transfer.

This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.

For the time being, only do it on CPM1 as there must be a
trade-off between the CPM load reduction and the CPU load required
to byte swap the data.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f2e981f20f92dd28983c3949702a09248c23845c.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/spi/spi-fsl-cpm.c |   23 +++++++++++++++++++++++
 drivers/spi/spi-fsl-spi.c |    3 +++
 2 files changed, 26 insertions(+)

--- a/drivers/spi/spi-fsl-cpm.c
+++ b/drivers/spi/spi-fsl-cpm.c
@@ -21,6 +21,7 @@
 #include <linux/spi/spi.h>
 #include <linux/types.h>
 #include <linux/platform_device.h>
+#include <linux/byteorder/generic.h>
 
 #include "spi-fsl-cpm.h"
 #include "spi-fsl-lib.h"
@@ -120,6 +121,21 @@ int fsl_spi_cpm_bufs(struct mpc8xxx_spi
 		mspi->rx_dma = mspi->dma_dummy_rx;
 		mspi->map_rx_dma = 0;
 	}
+	if (t->bits_per_word == 16 && t->tx_buf) {
+		const u16 *src = t->tx_buf;
+		u16 *dst;
+		int i;
+
+		dst = kmalloc(t->len, GFP_KERNEL);
+		if (!dst)
+			return -ENOMEM;
+
+		for (i = 0; i < t->len >> 1; i++)
+			dst[i] = cpu_to_le16p(src + i);
+
+		mspi->tx = dst;
+		mspi->map_tx_dma = 1;
+	}
 
 	if (mspi->map_tx_dma) {
 		void *nonconst_tx = (void *)mspi->tx; /* shut up gcc */
@@ -173,6 +189,13 @@ void fsl_spi_cpm_bufs_complete(struct mp
 	if (mspi->map_rx_dma)
 		dma_unmap_single(dev, mspi->rx_dma, t->len, DMA_FROM_DEVICE);
 	mspi->xfer_in_progress = NULL;
+
+	if (t->bits_per_word == 16 && t->rx_buf) {
+		int i;
+
+		for (i = 0; i < t->len; i += 2)
+			le16_to_cpus(t->rx_buf + i);
+	}
 }
 EXPORT_SYMBOL_GPL(fsl_spi_cpm_bufs_complete);
 
--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -368,6 +368,9 @@ static int fsl_spi_do_one_msg(struct spi
 				return -EINVAL;
 			if (t->bits_per_word == 16 || t->bits_per_word == 32)
 				t->bits_per_word = 8; /* pretend its 8 bits */
+			if (t->bits_per_word == 8 && t->len >= 256 &&
+			    (mpc8xxx_spi->flags & SPI_CPM1))
+				t->bits_per_word = 16;
 		}
 	}
 


Patches currently in stable-queue which might be from christophe.leroy@csgroup.eu are

queue-5.10/spi-fsl-cpm-use-16-bit-mode-for-large-transfers-with-even-size.patch
queue-5.10/spi-fsl-spi-re-organise-transfer-bits_per_word-adaptation.patch

Patch "Subject:[For 5.15/5.10/5.4] spi: fsl-spi: Re-organise transfer bits_per_word adaptation" has been added to the 5.10-stable tree

[gregkh]

This is a note to let you know that I've just added the patch titled

    Subject:[For 5.15/5.10/5.4] spi: fsl-spi: Re-organise transfer bits_per_word adaptation

to the 5.10-stable tree which can be found at:
    http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     spi-fsl-spi-re-organise-transfer-bits_per_word-adaptation.patch
and it can be found in the queue-5.10 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@vger.kernel.org> know about it.


From christophe.leroy@csgroup.eu Mon May 15 15:08:03 2023
From: Christophe Leroy <christophe.leroy@csgroup.eu>
Date: Mon, 15 May 2023 16:07:16 +0200
Subject:[For 5.15/5.10/5.4] spi: fsl-spi: Re-organise transfer bits_per_word adaptation
To: gregkh@linuxfoundation.org, stable@vger.kernel.org
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>, linux-kernel@vger.kernel.org, linuxppc-dev@lists.ozlabs.org, Mark Brown <broonie@kernel.org>
Message-ID: <1e4bfb4850ba849c316f48a0ab0d7123da0e2f54.1684156552.git.christophe.leroy@csgroup.eu>

From: Christophe Leroy <christophe.leroy@csgroup.eu>

(backported from upstream 8a5299a1278eadf1e08a598a5345c376206f171e)

For different reasons, fsl-spi driver performs bits_per_word
modifications for different reasons:
- On CPU mode, to minimise amount of interrupts
- On CPM/QE mode to work around controller byte order

For CPU mode that's done in fsl_spi_prepare_message() while
for CPM mode that's done in fsl_spi_setup_transfer().

Reunify all of it in fsl_spi_prepare_message(), and catch
impossible cases early through master's bits_per_word_mask
instead of returning EINVAL later.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/0ce96fe96e8b07cba0613e4097cfd94d09b8919a.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/spi/spi-fsl-spi.c |   50 +++++++++++++++++++++-------------------------
 1 file changed, 23 insertions(+), 27 deletions(-)

--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -203,26 +203,6 @@ static int mspi_apply_cpu_mode_quirks(st
 	return bits_per_word;
 }
 
-static int mspi_apply_qe_mode_quirks(struct spi_mpc8xxx_cs *cs,
-				struct spi_device *spi,
-				int bits_per_word)
-{
-	/* CPM/QE uses Little Endian for words > 8
-	 * so transform 16 and 32 bits words into 8 bits
-	 * Unfortnatly that doesn't work for LSB so
-	 * reject these for now */
-	/* Note: 32 bits word, LSB works iff
-	 * tfcr/rfcr is set to CPMFCR_GBL */
-	if (spi->mode & SPI_LSB_FIRST &&
-	    bits_per_word > 8)
-		return -EINVAL;
-	if (bits_per_word <= 8)
-		return bits_per_word;
-	if (bits_per_word == 16 || bits_per_word == 32)
-		return 8; /* pretend its 8 bits */
-	return -EINVAL;
-}
-
 static int fsl_spi_setup_transfer(struct spi_device *spi,
 					struct spi_transfer *t)
 {
@@ -250,9 +230,6 @@ static int fsl_spi_setup_transfer(struct
 		bits_per_word = mspi_apply_cpu_mode_quirks(cs, spi,
 							   mpc8xxx_spi,
 							   bits_per_word);
-	else
-		bits_per_word = mspi_apply_qe_mode_quirks(cs, spi,
-							  bits_per_word);
 
 	if (bits_per_word < 0)
 		return bits_per_word;
@@ -370,14 +347,27 @@ static int fsl_spi_do_one_msg(struct spi
 	 * In CPU mode, optimize large byte transfers to use larger
 	 * bits_per_word values to reduce number of interrupts taken.
 	 */
-	if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
-		list_for_each_entry(t, &m->transfers, transfer_list) {
+	list_for_each_entry(t, &m->transfers, transfer_list) {
+		if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
 			if (t->len < 256 || t->bits_per_word != 8)
 				continue;
 			if ((t->len & 3) == 0)
 				t->bits_per_word = 32;
 			else if ((t->len & 1) == 0)
 				t->bits_per_word = 16;
+		} else {
+			/*
+			 * CPM/QE uses Little Endian for words > 8
+			 * so transform 16 and 32 bits words into 8 bits
+			 * Unfortnatly that doesn't work for LSB so
+			 * reject these for now
+			 * Note: 32 bits word, LSB works iff
+			 * tfcr/rfcr is set to CPMFCR_GBL
+			 */
+			if (m->spi->mode & SPI_LSB_FIRST && t->bits_per_word > 8)
+				return -EINVAL;
+			if (t->bits_per_word == 16 || t->bits_per_word == 32)
+				t->bits_per_word = 8; /* pretend its 8 bits */
 		}
 	}
 
@@ -635,8 +625,14 @@ static struct spi_master *fsl_spi_probe(
 	if (mpc8xxx_spi->type == TYPE_GRLIB)
 		fsl_spi_grlib_probe(dev);
 
-	master->bits_per_word_mask =
-		(SPI_BPW_RANGE_MASK(4, 16) | SPI_BPW_MASK(32)) &
+	if (mpc8xxx_spi->flags & SPI_CPM_MODE)
+		master->bits_per_word_mask =
+			(SPI_BPW_RANGE_MASK(4, 8) | SPI_BPW_MASK(16) | SPI_BPW_MASK(32));
+	else
+		master->bits_per_word_mask =
+			(SPI_BPW_RANGE_MASK(4, 16) | SPI_BPW_MASK(32));
+
+	master->bits_per_word_mask &=
 		SPI_BPW_RANGE_MASK(1, mpc8xxx_spi->max_bits_per_word);
 
 	if (mpc8xxx_spi->flags & SPI_QE_CPU_MODE)


Patches currently in stable-queue which might be from christophe.leroy@csgroup.eu are

queue-5.10/spi-fsl-cpm-use-16-bit-mode-for-large-transfers-with-even-size.patch
queue-5.10/spi-fsl-spi-re-organise-transfer-bits_per_word-adaptation.patch

Patch "Subject:[For 5.15/5.10/5.4] spi: fsl-cpm: Use 16 bit mode for large transfers with even size" has been added to the 5.15-stable tree

[gregkh]

This is a note to let you know that I've just added the patch titled

    Subject:[For 5.15/5.10/5.4] spi: fsl-cpm: Use 16 bit mode for large transfers with even size

to the 5.15-stable tree which can be found at:
    http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     spi-fsl-cpm-use-16-bit-mode-for-large-transfers-with-even-size.patch
and it can be found in the queue-5.15 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@vger.kernel.org> know about it.


From christophe.leroy@csgroup.eu Mon May 15 15:07:59 2023
From: Christophe Leroy <christophe.leroy@csgroup.eu>
Date: Mon, 15 May 2023 16:07:17 +0200
Subject:[For 5.15/5.10/5.4] spi: fsl-cpm: Use 16 bit mode for large transfers with even size
To: gregkh@linuxfoundation.org, stable@vger.kernel.org
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>, linux-kernel@vger.kernel.org, linuxppc-dev@lists.ozlabs.org, Mark Brown <broonie@kernel.org>
Message-ID: <3a1b8774ad7004acb594fbf220f98488dbaa2896.1684156552.git.christophe.leroy@csgroup.eu>

From: Christophe Leroy <christophe.leroy@csgroup.eu>

(cherry picked from upstream fc96ec826bced75cc6b9c07a4ac44bbf651337ab)

On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped as seen in a previous commit.

So, for large tranfers with an even size, allocate a temporary tx
buffer and byte-swap data before and after transfer.

This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.

For the time being, only do it on CPM1 as there must be a
trade-off between the CPM load reduction and the CPU load required
to byte swap the data.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f2e981f20f92dd28983c3949702a09248c23845c.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/spi/spi-fsl-cpm.c |   23 +++++++++++++++++++++++
 drivers/spi/spi-fsl-spi.c |    3 +++
 2 files changed, 26 insertions(+)

--- a/drivers/spi/spi-fsl-cpm.c
+++ b/drivers/spi/spi-fsl-cpm.c
@@ -21,6 +21,7 @@
 #include <linux/spi/spi.h>
 #include <linux/types.h>
 #include <linux/platform_device.h>
+#include <linux/byteorder/generic.h>
 
 #include "spi-fsl-cpm.h"
 #include "spi-fsl-lib.h"
@@ -120,6 +121,21 @@ int fsl_spi_cpm_bufs(struct mpc8xxx_spi
 		mspi->rx_dma = mspi->dma_dummy_rx;
 		mspi->map_rx_dma = 0;
 	}
+	if (t->bits_per_word == 16 && t->tx_buf) {
+		const u16 *src = t->tx_buf;
+		u16 *dst;
+		int i;
+
+		dst = kmalloc(t->len, GFP_KERNEL);
+		if (!dst)
+			return -ENOMEM;
+
+		for (i = 0; i < t->len >> 1; i++)
+			dst[i] = cpu_to_le16p(src + i);
+
+		mspi->tx = dst;
+		mspi->map_tx_dma = 1;
+	}
 
 	if (mspi->map_tx_dma) {
 		void *nonconst_tx = (void *)mspi->tx; /* shut up gcc */
@@ -173,6 +189,13 @@ void fsl_spi_cpm_bufs_complete(struct mp
 	if (mspi->map_rx_dma)
 		dma_unmap_single(dev, mspi->rx_dma, t->len, DMA_FROM_DEVICE);
 	mspi->xfer_in_progress = NULL;
+
+	if (t->bits_per_word == 16 && t->rx_buf) {
+		int i;
+
+		for (i = 0; i < t->len; i += 2)
+			le16_to_cpus(t->rx_buf + i);
+	}
 }
 EXPORT_SYMBOL_GPL(fsl_spi_cpm_bufs_complete);
 
--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -368,6 +368,9 @@ static int fsl_spi_do_one_msg(struct spi
 				return -EINVAL;
 			if (t->bits_per_word == 16 || t->bits_per_word == 32)
 				t->bits_per_word = 8; /* pretend its 8 bits */
+			if (t->bits_per_word == 8 && t->len >= 256 &&
+			    (mpc8xxx_spi->flags & SPI_CPM1))
+				t->bits_per_word = 16;
 		}
 	}
 


Patches currently in stable-queue which might be from christophe.leroy@csgroup.eu are

queue-5.15/spi-fsl-cpm-use-16-bit-mode-for-large-transfers-with-even-size.patch
queue-5.15/spi-fsl-spi-re-organise-transfer-bits_per_word-adaptation.patch

Patch "Subject:[For 5.15/5.10/5.4] spi: fsl-spi: Re-organise transfer bits_per_word adaptation" has been added to the 5.15-stable tree

[gregkh]

This is a note to let you know that I've just added the patch titled

    Subject:[For 5.15/5.10/5.4] spi: fsl-spi: Re-organise transfer bits_per_word adaptation

to the 5.15-stable tree which can be found at:
    http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     spi-fsl-spi-re-organise-transfer-bits_per_word-adaptation.patch
and it can be found in the queue-5.15 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@vger.kernel.org> know about it.


From christophe.leroy@csgroup.eu Mon May 15 15:08:03 2023
From: Christophe Leroy <christophe.leroy@csgroup.eu>
Date: Mon, 15 May 2023 16:07:16 +0200
Subject:[For 5.15/5.10/5.4] spi: fsl-spi: Re-organise transfer bits_per_word adaptation
To: gregkh@linuxfoundation.org, stable@vger.kernel.org
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>, linux-kernel@vger.kernel.org, linuxppc-dev@lists.ozlabs.org, Mark Brown <broonie@kernel.org>
Message-ID: <1e4bfb4850ba849c316f48a0ab0d7123da0e2f54.1684156552.git.christophe.leroy@csgroup.eu>

From: Christophe Leroy <christophe.leroy@csgroup.eu>

(backported from upstream 8a5299a1278eadf1e08a598a5345c376206f171e)

For different reasons, fsl-spi driver performs bits_per_word
modifications for different reasons:
- On CPU mode, to minimise amount of interrupts
- On CPM/QE mode to work around controller byte order

For CPU mode that's done in fsl_spi_prepare_message() while
for CPM mode that's done in fsl_spi_setup_transfer().

Reunify all of it in fsl_spi_prepare_message(), and catch
impossible cases early through master's bits_per_word_mask
instead of returning EINVAL later.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/0ce96fe96e8b07cba0613e4097cfd94d09b8919a.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/spi/spi-fsl-spi.c |   50 +++++++++++++++++++++-------------------------
 1 file changed, 23 insertions(+), 27 deletions(-)

--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -203,26 +203,6 @@ static int mspi_apply_cpu_mode_quirks(st
 	return bits_per_word;
 }
 
-static int mspi_apply_qe_mode_quirks(struct spi_mpc8xxx_cs *cs,
-				struct spi_device *spi,
-				int bits_per_word)
-{
-	/* CPM/QE uses Little Endian for words > 8
-	 * so transform 16 and 32 bits words into 8 bits
-	 * Unfortnatly that doesn't work for LSB so
-	 * reject these for now */
-	/* Note: 32 bits word, LSB works iff
-	 * tfcr/rfcr is set to CPMFCR_GBL */
-	if (spi->mode & SPI_LSB_FIRST &&
-	    bits_per_word > 8)
-		return -EINVAL;
-	if (bits_per_word <= 8)
-		return bits_per_word;
-	if (bits_per_word == 16 || bits_per_word == 32)
-		return 8; /* pretend its 8 bits */
-	return -EINVAL;
-}
-
 static int fsl_spi_setup_transfer(struct spi_device *spi,
 					struct spi_transfer *t)
 {
@@ -250,9 +230,6 @@ static int fsl_spi_setup_transfer(struct
 		bits_per_word = mspi_apply_cpu_mode_quirks(cs, spi,
 							   mpc8xxx_spi,
 							   bits_per_word);
-	else
-		bits_per_word = mspi_apply_qe_mode_quirks(cs, spi,
-							  bits_per_word);
 
 	if (bits_per_word < 0)
 		return bits_per_word;
@@ -370,14 +347,27 @@ static int fsl_spi_do_one_msg(struct spi
 	 * In CPU mode, optimize large byte transfers to use larger
 	 * bits_per_word values to reduce number of interrupts taken.
 	 */
-	if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
-		list_for_each_entry(t, &m->transfers, transfer_list) {
+	list_for_each_entry(t, &m->transfers, transfer_list) {
+		if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
 			if (t->len < 256 || t->bits_per_word != 8)
 				continue;
 			if ((t->len & 3) == 0)
 				t->bits_per_word = 32;
 			else if ((t->len & 1) == 0)
 				t->bits_per_word = 16;
+		} else {
+			/*
+			 * CPM/QE uses Little Endian for words > 8
+			 * so transform 16 and 32 bits words into 8 bits
+			 * Unfortnatly that doesn't work for LSB so
+			 * reject these for now
+			 * Note: 32 bits word, LSB works iff
+			 * tfcr/rfcr is set to CPMFCR_GBL
+			 */
+			if (m->spi->mode & SPI_LSB_FIRST && t->bits_per_word > 8)
+				return -EINVAL;
+			if (t->bits_per_word == 16 || t->bits_per_word == 32)
+				t->bits_per_word = 8; /* pretend its 8 bits */
 		}
 	}
 
@@ -635,8 +625,14 @@ static struct spi_master *fsl_spi_probe(
 	if (mpc8xxx_spi->type == TYPE_GRLIB)
 		fsl_spi_grlib_probe(dev);
 
-	master->bits_per_word_mask =
-		(SPI_BPW_RANGE_MASK(4, 16) | SPI_BPW_MASK(32)) &
+	if (mpc8xxx_spi->flags & SPI_CPM_MODE)
+		master->bits_per_word_mask =
+			(SPI_BPW_RANGE_MASK(4, 8) | SPI_BPW_MASK(16) | SPI_BPW_MASK(32));
+	else
+		master->bits_per_word_mask =
+			(SPI_BPW_RANGE_MASK(4, 16) | SPI_BPW_MASK(32));
+
+	master->bits_per_word_mask &=
 		SPI_BPW_RANGE_MASK(1, mpc8xxx_spi->max_bits_per_word);
 
 	if (mpc8xxx_spi->flags & SPI_QE_CPU_MODE)


Patches currently in stable-queue which might be from christophe.leroy@csgroup.eu are

queue-5.15/spi-fsl-cpm-use-16-bit-mode-for-large-transfers-with-even-size.patch
queue-5.15/spi-fsl-spi-re-organise-transfer-bits_per_word-adaptation.patch

Patch "spi: fsl-cpm: Use 16 bit mode for large transfers with even size" has been added to the 5.4-stable tree

[gregkh]

This is a note to let you know that I've just added the patch titled

    spi: fsl-cpm: Use 16 bit mode for large transfers with even size

to the 5.4-stable tree which can be found at:
    http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     spi-fsl-cpm-use-16-bit-mode-for-large-transfers-with-even-size.patch
and it can be found in the queue-5.4 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@vger.kernel.org> know about it.


From christophe.leroy@csgroup.eu Mon May 15 15:07:59 2023
From: Christophe Leroy <christophe.leroy@csgroup.eu>
Date: Mon, 15 May 2023 16:07:17 +0200
Subject: spi: fsl-cpm: Use 16 bit mode for large transfers with even size
To: gregkh@linuxfoundation.org, stable@vger.kernel.org
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>, linux-kernel@vger.kernel.org, linuxppc-dev@lists.ozlabs.org, Mark Brown <broonie@kernel.org>
Message-ID: <3a1b8774ad7004acb594fbf220f98488dbaa2896.1684156552.git.christophe.leroy@csgroup.eu>

From: Christophe Leroy <christophe.leroy@csgroup.eu>

(cherry picked from upstream fc96ec826bced75cc6b9c07a4ac44bbf651337ab)

On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped as seen in a previous commit.

So, for large tranfers with an even size, allocate a temporary tx
buffer and byte-swap data before and after transfer.

This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.

For the time being, only do it on CPM1 as there must be a
trade-off between the CPM load reduction and the CPU load required
to byte swap the data.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f2e981f20f92dd28983c3949702a09248c23845c.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/spi/spi-fsl-cpm.c |   23 +++++++++++++++++++++++
 drivers/spi/spi-fsl-spi.c |    3 +++
 2 files changed, 26 insertions(+)

--- a/drivers/spi/spi-fsl-cpm.c
+++ b/drivers/spi/spi-fsl-cpm.c
@@ -21,6 +21,7 @@
 #include <linux/spi/spi.h>
 #include <linux/types.h>
 #include <linux/platform_device.h>
+#include <linux/byteorder/generic.h>
 
 #include "spi-fsl-cpm.h"
 #include "spi-fsl-lib.h"
@@ -120,6 +121,21 @@ int fsl_spi_cpm_bufs(struct mpc8xxx_spi
 		mspi->rx_dma = mspi->dma_dummy_rx;
 		mspi->map_rx_dma = 0;
 	}
+	if (t->bits_per_word == 16 && t->tx_buf) {
+		const u16 *src = t->tx_buf;
+		u16 *dst;
+		int i;
+
+		dst = kmalloc(t->len, GFP_KERNEL);
+		if (!dst)
+			return -ENOMEM;
+
+		for (i = 0; i < t->len >> 1; i++)
+			dst[i] = cpu_to_le16p(src + i);
+
+		mspi->tx = dst;
+		mspi->map_tx_dma = 1;
+	}
 
 	if (mspi->map_tx_dma) {
 		void *nonconst_tx = (void *)mspi->tx; /* shut up gcc */
@@ -173,6 +189,13 @@ void fsl_spi_cpm_bufs_complete(struct mp
 	if (mspi->map_rx_dma)
 		dma_unmap_single(dev, mspi->rx_dma, t->len, DMA_FROM_DEVICE);
 	mspi->xfer_in_progress = NULL;
+
+	if (t->bits_per_word == 16 && t->rx_buf) {
+		int i;
+
+		for (i = 0; i < t->len; i += 2)
+			le16_to_cpus(t->rx_buf + i);
+	}
 }
 EXPORT_SYMBOL_GPL(fsl_spi_cpm_bufs_complete);
 
--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -369,6 +369,9 @@ static int fsl_spi_do_one_msg(struct spi
 				return -EINVAL;
 			if (t->bits_per_word == 16 || t->bits_per_word == 32)
 				t->bits_per_word = 8; /* pretend its 8 bits */
+			if (t->bits_per_word == 8 && t->len >= 256 &&
+			    (mpc8xxx_spi->flags & SPI_CPM1))
+				t->bits_per_word = 16;
 		}
 	}
 


Patches currently in stable-queue which might be from christophe.leroy@csgroup.eu are

queue-5.4/spi-fsl-cpm-use-16-bit-mode-for-large-transfers-with-even-size.patch
queue-5.4/spi-fsl-spi-re-organise-transfer-bits_per_word-adaptation.patch

Patch "spi: fsl-spi: Re-organise transfer bits_per_word adaptation" has been added to the 5.4-stable tree

[gregkh]

This is a note to let you know that I've just added the patch titled

    spi: fsl-spi: Re-organise transfer bits_per_word adaptation

to the 5.4-stable tree which can be found at:
    http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     spi-fsl-spi-re-organise-transfer-bits_per_word-adaptation.patch
and it can be found in the queue-5.4 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@vger.kernel.org> know about it.


From christophe.leroy@csgroup.eu Mon May 15 15:08:03 2023
From: Christophe Leroy <christophe.leroy@csgroup.eu>
Date: Mon, 15 May 2023 16:07:16 +0200
Subject: spi: fsl-spi: Re-organise transfer bits_per_word adaptation
To: gregkh@linuxfoundation.org, stable@vger.kernel.org
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>, linux-kernel@vger.kernel.org, linuxppc-dev@lists.ozlabs.org, Mark Brown <broonie@kernel.org>
Message-ID: <1e4bfb4850ba849c316f48a0ab0d7123da0e2f54.1684156552.git.christophe.leroy@csgroup.eu>

From: Christophe Leroy <christophe.leroy@csgroup.eu>

(backported from upstream 8a5299a1278eadf1e08a598a5345c376206f171e)

For different reasons, fsl-spi driver performs bits_per_word
modifications for different reasons:
- On CPU mode, to minimise amount of interrupts
- On CPM/QE mode to work around controller byte order

For CPU mode that's done in fsl_spi_prepare_message() while
for CPM mode that's done in fsl_spi_setup_transfer().

Reunify all of it in fsl_spi_prepare_message(), and catch
impossible cases early through master's bits_per_word_mask
instead of returning EINVAL later.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/0ce96fe96e8b07cba0613e4097cfd94d09b8919a.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/spi/spi-fsl-spi.c |   50 +++++++++++++++++++++-------------------------
 1 file changed, 23 insertions(+), 27 deletions(-)

--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -204,26 +204,6 @@ static int mspi_apply_cpu_mode_quirks(st
 	return bits_per_word;
 }
 
-static int mspi_apply_qe_mode_quirks(struct spi_mpc8xxx_cs *cs,
-				struct spi_device *spi,
-				int bits_per_word)
-{
-	/* CPM/QE uses Little Endian for words > 8
-	 * so transform 16 and 32 bits words into 8 bits
-	 * Unfortnatly that doesn't work for LSB so
-	 * reject these for now */
-	/* Note: 32 bits word, LSB works iff
-	 * tfcr/rfcr is set to CPMFCR_GBL */
-	if (spi->mode & SPI_LSB_FIRST &&
-	    bits_per_word > 8)
-		return -EINVAL;
-	if (bits_per_word <= 8)
-		return bits_per_word;
-	if (bits_per_word == 16 || bits_per_word == 32)
-		return 8; /* pretend its 8 bits */
-	return -EINVAL;
-}
-
 static int fsl_spi_setup_transfer(struct spi_device *spi,
 					struct spi_transfer *t)
 {
@@ -251,9 +231,6 @@ static int fsl_spi_setup_transfer(struct
 		bits_per_word = mspi_apply_cpu_mode_quirks(cs, spi,
 							   mpc8xxx_spi,
 							   bits_per_word);
-	else
-		bits_per_word = mspi_apply_qe_mode_quirks(cs, spi,
-							  bits_per_word);
 
 	if (bits_per_word < 0)
 		return bits_per_word;
@@ -371,14 +348,27 @@ static int fsl_spi_do_one_msg(struct spi
 	 * In CPU mode, optimize large byte transfers to use larger
 	 * bits_per_word values to reduce number of interrupts taken.
 	 */
-	if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
-		list_for_each_entry(t, &m->transfers, transfer_list) {
+	list_for_each_entry(t, &m->transfers, transfer_list) {
+		if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
 			if (t->len < 256 || t->bits_per_word != 8)
 				continue;
 			if ((t->len & 3) == 0)
 				t->bits_per_word = 32;
 			else if ((t->len & 1) == 0)
 				t->bits_per_word = 16;
+		} else {
+			/*
+			 * CPM/QE uses Little Endian for words > 8
+			 * so transform 16 and 32 bits words into 8 bits
+			 * Unfortnatly that doesn't work for LSB so
+			 * reject these for now
+			 * Note: 32 bits word, LSB works iff
+			 * tfcr/rfcr is set to CPMFCR_GBL
+			 */
+			if (m->spi->mode & SPI_LSB_FIRST && t->bits_per_word > 8)
+				return -EINVAL;
+			if (t->bits_per_word == 16 || t->bits_per_word == 32)
+				t->bits_per_word = 8; /* pretend its 8 bits */
 		}
 	}
 
@@ -637,8 +627,14 @@ static struct spi_master * fsl_spi_probe
 	if (mpc8xxx_spi->type == TYPE_GRLIB)
 		fsl_spi_grlib_probe(dev);
 
-	master->bits_per_word_mask =
-		(SPI_BPW_RANGE_MASK(4, 16) | SPI_BPW_MASK(32)) &
+	if (mpc8xxx_spi->flags & SPI_CPM_MODE)
+		master->bits_per_word_mask =
+			(SPI_BPW_RANGE_MASK(4, 8) | SPI_BPW_MASK(16) | SPI_BPW_MASK(32));
+	else
+		master->bits_per_word_mask =
+			(SPI_BPW_RANGE_MASK(4, 16) | SPI_BPW_MASK(32));
+
+	master->bits_per_word_mask &=
 		SPI_BPW_RANGE_MASK(1, mpc8xxx_spi->max_bits_per_word);
 
 	if (mpc8xxx_spi->flags & SPI_QE_CPU_MODE)


Patches currently in stable-queue which might be from christophe.leroy@csgroup.eu are

queue-5.4/spi-fsl-cpm-use-16-bit-mode-for-large-transfers-with-even-size.patch
queue-5.4/spi-fsl-spi-re-organise-transfer-bits_per_word-adaptation.patch