linuxppc-dev.lists.ozlabs.org archive mirror
 help / color / mirror / Atom feed
From: Erhard Furtner <erhard_f@mailbox.org>
To: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: "linuxppc-dev@lists.ozlabs.org" <linuxppc-dev@lists.ozlabs.org>
Subject: Re: KASAN debug kernel fails to boot at early stage when CONFIG_SMP=y is set (kernel 6.5-rc5, PowerMac G4 3,6)
Date: Sun, 13 Aug 2023 21:38:55 +0200	[thread overview]
Message-ID: <20230813213855.794b3c8f@yea> (raw)
In-Reply-To: <f8f09049-3568-621d-88ce-1b61fe8b63fe@csgroup.eu>

[-- Attachment #1: Type: text/plain, Size: 1462 bytes --]

On Fri, 11 Aug 2023 06:45:14 +0000
Christophe Leroy <christophe.leroy@csgroup.eu> wrote:

> Le 11/08/2023 à 01:48, Erhard Furtner a écrit :
> > I wanted to fire up my PowerMac G4 MDD (Dual CPU) with a KASAN debug build of kernel 6.5-rc5 for testing purposes. But the kernel fails to boot at a very early stage. I only get a white screen reading
> > "done
> > found display: /pci@f0000000/ATY,AlteracParent@10/ATY,Alterac_B@1, opening..."  
> 
> Can you try with CONFIG_PPC_EARLY_DEBUG and see if you get more 
> information on the screen ?

With CONFIG_PPC_EARLY_DEBUG set booting continues and I get two more lines on a white screen:

[    0.000000] printk: bootconsole [udbg0] enabled
[    0.000000] Total memory = 2048MB; using 4096kB for hash table

Afterwards the G4 freezes.

By chane I found out another interesting thing: This only happens on cold boots.

If I boot the G4 up with another kernel first and boot the SMP KASAN kernel afterwards it just boots up fine too! On further reboots the SMP KASAN kernel keeps booting up normally. Until I turn the machine off - and next time I turn it on the same SMP KASAN kernel fails booting again as described. Strange...

This behaviour however is reproducible. Tried that procedure 15-20 times just to be sure. Hope you can make something out of it.

Attached is a dmesg of a successful SMP KASAM kernel boot attempt when a working kernel was booted first.

Regards,
Erhard F.

[-- Attachment #2: dmesg_65-rc5_g4_04 --]
[-- Type: application/octet-stream, Size: 50246 bytes --]

[    0.000000] printk: bootconsole [udbg0] enabled
[    0.000000] Total memory = 2048MB; using 4096kB for hash table
[    0.000000] Activating Kernel Userspace Access Protection
[    0.000000] Activating Kernel Userspace Execution Prevention
[    0.000000] Linux version 6.5.0-rc5-PMacG4 (root@T1000) (gcc (Gentoo 12.3.1_p20230526 p2) 12.3.1 20230526, GNU ld (Gentoo 2.40 p7) 2.40.0) #2 SMP Sun Aug 13 10:56:19 CEST 2023
[    0.000000] KASAN init done
[    0.000000] ioremap() called early from pmac_feature_init+0x17c/0xea0. Use early_ioremap() instead
[    0.000000] Found UniNorth memory controller & host bridge @ 0xf8000000 revision: 0x24
[    0.000000] Mapped at 0xf53bf000
[    0.000000] ioremap() called early from probe_one_macio+0x1f8/0x400. Use early_ioremap() instead
[    0.000000] Found a Keylargo mac-io controller, rev: 3, mapped at 0x(ptrval)
[    0.000000] PowerMac motherboard: PowerMac G4 Windtunnel
[    0.000000] ioremap() called early from btext_map+0x64/0xdc. Use early_ioremap() instead
[    0.000000] Hardware name: PowerMac3,6 7455 0x80010303 PowerMac
[    0.000000] CPU maps initialized for 1 thread per core
[    0.000000]  (thread shift is 0)
[    0.000000] -----------------------------------------------------
[    0.000000] phys_mem_size     = 0x80000000
[    0.000000] dcache_bsize      = 0x20
[    0.000000] icache_bsize      = 0x20
[    0.000000] cpu_features      = 0x000000002514600a
[    0.000000]   possible        = 0x00000000277de00a
[    0.000000]   always          = 0x0000000001000000
[    0.000000] cpu_user_features = 0x9c000001 0x00000000
[    0.000000] mmu_features      = 0x00010001
[    0.000000] Hash_size         = 0x400000
[    0.000000] Hash_mask         = 0xffff
[    0.000000] -----------------------------------------------------
[    0.000000] ioremap() called early from pmac_setup_arch+0x1ac/0x448. Use early_ioremap() instead
[    0.000000] ioremap() called early from find_via_pmu+0x2a8/0x434. Use early_ioremap() instead
[    0.000000] ioremap() called early from find_via_pmu+0x2e4/0x434. Use early_ioremap() instead
[    0.000000] via-pmu: Server Mode is disabled
[    0.000000] PMU driver v2 initialized for Core99, firmware: 0c
[    0.000000] ioremap() called early from pmac_nvram_init+0x208/0x7c4. Use early_ioremap() instead
[    0.000000] nvram: Checking bank 0...
[    0.000000] nvram: gen0=3180, gen1=3181
[    0.000000] nvram: Active bank is: 1
[    0.000000] nvram: OF partition at 0x410
[    0.000000] nvram: XP partition at 0x1020
[    0.000000] nvram: NR partition at 0x1120
[    0.000000] Top of RAM: 0x80000000, Total RAM: 0x80000000
[    0.000000] Memory hole size: 0MB
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x000000002fffffff]
[    0.000000]   Normal   empty
[    0.000000]   HighMem  [mem 0x0000000030000000-0x000000007fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000007fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[    0.000000] percpu: Embedded 14 pages/cpu s24672 r8192 d24480 u57344
[    0.000000] pcpu-alloc: s24672 r8192 d24480 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Kernel command line: ro root=/dev/sda5 zswap.max_pool_percent=16 slub_debug=FZP page_poison=1 netconsole=6666@192.168.178.8/eth0,6666@192.168.178.3/70:85:C2:30:EC:01 init=/usr/lib/systemd/systemd 
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 522560
[    0.000000] mem auto-init: stack:all(pattern), heap alloc:off, heap free:off
[    0.000000] stackdepot: allocating hash table via alloc_large_system_hash
[    0.000000] stackdepot hash table entries: 1048576 (order: 10, 4194304 bytes, linear)
[    0.000000] Kernel virtual memory layout:
[    0.000000]   * 0xf6000000..0xfec00000  : kasan shadow mem
[    0.000000]   * 0xf5bbf000..0xf5fff000  : fixmap
[    0.000000]   * 0xf5400000..0xf5800000  : highmem PTEs
[    0.000000]   * 0xf5115000..0xf5400000  : early ioremap
[    0.000000]   * 0xf1000000..0xf5110000  : vmalloc & ioremap
[    0.000000]   * 0xb0000000..0xc0000000  : modules
[    0.000000] Memory: 1946548K/2097152K available (16068K kernel code, 1964K rwdata, 4412K rodata, 1344K init, 405K bss, 150604K reserved, 0K cma-reserved, 1212416K highmem)
[    0.000000] **********************************************************
[    0.000000] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
[    0.000000] **                                                      **
[    0.000000] ** This system shows unhashed kernel memory addresses   **
[    0.000000] ** via the console, logs, and other interfaces. This    **
[    0.000000] ** might reduce the security of your system.            **
[    0.000000] **                                                      **
[    0.000000] ** If you see this message and you are not debugging    **
[    0.000000] ** the kernel, report this immediately to your system   **
[    0.000000] ** administrator!                                       **
[    0.000000] **                                                      **
[    0.000000] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
[    0.000000] **********************************************************
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    0.000000] NR_IRQS: 512, nr_irqs: 512, preallocated irqs: 16
[    0.000000] mpic: Resetting
[    0.000000] mpic: Setting up MPIC " MPIC 1   " version 1.2 at 80040000, max 2 CPUs
[    0.000000] mpic: ISU size: 64, shift: 6, mask: 3f
[    0.000000] mpic: Initializing for 64 sources
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] time_init: decrementer frequency = 41.658765 MHz
[    0.000000] time_init: processor frequency   = 1416.666661 MHz
[    0.000009] clocksource: timebase: mask: 0xffffffffffffffff max_cycles: 0x99b97f1da, max_idle_ns: 440795202966 ns
[    0.000563] clocksource: timebase mult[18012a56] shift[24] registered
[    0.001064] clockevent: decrementer mult[aaa2619] shift[32] cpu[0]
[    0.003951] Console: colour dummy device 80x25
[    0.004485] printk: console [tty0] enabled
[    0.004945] printk: bootconsole [udbg0] disabled
[    0.006120] pid_max: default: 32768 minimum: 301
[    0.012346] LSM: initializing lsm=capability,yama
[    0.012439] Yama: becoming mindful.
[    0.014416] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.014635] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.030009] PowerMac SMP probe found 2 cpus
[    0.030789] KeyWest i2c @0xf8001003 irq 42 /uni-n@f8000000/i2c@f8001000
[    0.030955]  channel 0 bus <multibus>
[    0.031070]  channel 1 bus <multibus>
[    0.031503] KeyWest i2c @0x80018000 irq 26 /pci@f2000000/mac-io@17/i2c@18000
[    0.031661]  channel 0 bus <multibus>
[    0.031800] PMU i2c /pci@f2000000/mac-io@17/via-pmu@16000/pmu-i2c
[    0.031945]  channel 1 bus <multibus>
[    0.032056]  channel 2 bus <multibus>
[    0.032128] pmf: no parser for command 17 !
[    0.032290] Processor timebase sync using GPIO 0x73
[    0.032326] mpic: requesting IPIs...
[    0.032690] CPU0: L2CR is 80000000
[    0.032723] CPU0: L3CR is 9c030000
[    0.038904] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1.
[    0.040202] MPC7450 family performance monitor hardware support registered
[    0.041156] rcu: Hierarchical SRCU implementation.
[    0.041204] rcu: 	Max phase no-delay instances is 1000.
[    0.044155] smp: Bringing up secondary CPUs ...
[83973664.849722] CPU1: L2CR was 0
[83973664.849807] CPU1: L2CR set to 80000000
[83973664.849820] CPU1: L3CR was 0
[83973664.849970] CPU1: L3CR set to 9c030000
[    0.051016] smp: Brought up 1 node, 2 CPUs
[    0.056978] devtmpfs: initialized
[    0.060701] Duplicate name in PowerPC,G4@0, renamed to "l2-cache#1"
[    0.061258] Duplicate name in l2-cache#1, renamed to "l2-cache#1"
[    0.063688] Duplicate name in PowerPC,G4@1, renamed to "l2-cache#1"
[    0.064235] Duplicate name in l2-cache#1, renamed to "l2-cache#1"
[    0.090884] Duplicate name in gpio@50, renamed to "gpio5@6f#1"
[    0.091298] Duplicate name in gpio@50, renamed to "gpio6@70#1"
[    0.092243] Duplicate name in gpio@50, renamed to "gpio11@75#1"
[    0.092777] Duplicate name in gpio@50, renamed to "extint-gpio15@67#1"
[    0.130854] Found UniNorth PCI host bridge at 0x00000000f0000000. Firmware bus number: 0->0
[    0.130966] PCI host bridge /pci@f0000000  ranges:
[    0.131066]  MEM 0x00000000f1000000..0x00000000f1ffffff -> 0x00000000f1000000 
[    0.131143]   IO 0x00000000f0000000..0x00000000f07fffff -> 0x0000000000000000
[    0.151524]  MEM 0x0000000090000000..0x00000000afffffff -> 0x0000000090000000 
[    0.151920] Found UniNorth PCI host bridge at 0x00000000f2000000. Firmware bus number: 0->0
[    0.151982] PCI host bridge /pci@f2000000 (primary) ranges:
[    0.152078]  MEM 0x00000000f3000000..0x00000000f3ffffff -> 0x00000000f3000000 
[    0.152155]   IO 0x00000000f2000000..0x00000000f27fffff -> 0x0000000000000000
[    0.172658]  MEM 0x0000000080000000..0x000000008fffffff -> 0x0000000080000000 
[    0.173635] Found UniNorth PCI host bridge at 0x00000000f4000000. Firmware bus number: 0->0
[    0.173703] PCI host bridge /pci@f4000000  ranges:
[    0.173798]  MEM 0x00000000f5000000..0x00000000f5ffffff -> 0x00000000f5000000 
[    0.173862]   IO 0x00000000f4000000..0x00000000f47fffff -> 0x0000000000000000
[    0.194642] Found NEC PD720100A USB2 chip with disabled EHCI, fixing up...
[    0.196885] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.197265] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.199706] prandom: seed boundary self test passed
[    0.207507] prandom: 100 self tests passed
[    0.215336] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.251978] PCI: Probing PCI hardware
[    0.254858] PCI host bridge to bus 0000:00
[    0.254941] pci_bus 0000:00: root bus resource [io  0xff780000-0xfff7ffff] (bus address [0x0000-0x7fffff])
[    0.255025] pci_bus 0000:00: root bus resource [mem 0xf1000000-0xf1ffffff]
[    0.255088] pci_bus 0000:00: root bus resource [mem 0x90000000-0xafffffff]
[    0.255157] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.255209] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to ff
[    0.256925] pci 0000:00:0b.0: [106b:0034] type 00 class 0x060000
[    0.259239] pci 0000:00:10.0: [1002:4150] type 00 class 0x030000
[    0.259329] pci 0000:00:10.0: reg 0x10: [mem 0xa0000000-0xafffffff pref]
[    0.259394] pci 0000:00:10.0: reg 0x14: [io  0xff780400-0xff7804ff]
[    0.259454] pci 0000:00:10.0: reg 0x18: [mem 0x90000000-0x9000ffff]
[    0.259539] pci 0000:00:10.0: reg 0x30: [mem 0x90020000-0x9003ffff pref]
[    0.259665] pci 0000:00:10.0: supports D1 D2
[    0.263579] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.266221] OF: /pci@f2000000/mac-io@17/gpio@50/gpio5@6f: could not find phandle 1751474532
[    0.266402] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio15@67: could not find phandle 1751474532
[    0.266597] OF: /pci@f2000000/mac-io@17/gpio@50/gpio6@70: could not find phandle 1634562093
[    0.266763] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio16@68: could not find phandle 1936745825
[    0.267082] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio14@66: could not find phandle 1818848869
[    0.267282] OF: /pci@f2000000/mac-io@17/gpio@50/gpio12@76: could not find phandle 1835103092
[    0.267439] OF: /pci@f2000000/mac-io@17/gpio@50/gpio11@75: could not find phandle 1635083369
[    0.267586] OF: /pci@f2000000/mac-io@17/gpio@50/gpio5@6f: could not find phandle 1751474532
[    0.267734] OF: /pci@f2000000/mac-io@17/gpio@50/gpio6@70: could not find phandle 1634562093
[    0.267881] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio4@5c: could not find phandle 1818848869
[    0.268070] OF: /pci@f2000000/mac-io@17/gpio@50/gpio11@75: could not find phandle 1635083369
[    0.268219] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio15@67: could not find phandle 1751474532
[    0.271622] pci_bus 0001:00: Fixed dependency cycle(s) with /pci@f2000000/mac-io@17/interrupt-controller@40000
[    0.271905] PCI host bridge to bus 0001:00
[    0.271960] pci_bus 0001:00: root bus resource [io  0x0000-0x7fffff]
[    0.272023] pci_bus 0001:00: root bus resource [mem 0xf3000000-0xf3ffffff]
[    0.272086] pci_bus 0001:00: root bus resource [mem 0x80000000-0x8fffffff]
[    0.272152] pci_bus 0001:00: root bus resource [bus 00-ff]
[    0.272202] pci_bus 0001:00: busn_res: [bus 00-ff] end is updated to ff
[    0.273862] pci 0001:00:0b.0: [106b:0035] type 00 class 0x060000
[    0.276754] pci 0001:00:12.0: [1033:0035] type 00 class 0x0c0310
[    0.276842] pci 0001:00:12.0: reg 0x10: [mem 0x8008c000-0x8008cfff]
[    0.277065] pci 0001:00:12.0: supports D1 D2
[    0.277112] pci 0001:00:12.0: PME# supported from D0 D1 D2 D3hot
[    0.279335] pci 0001:00:12.1: [1033:0035] type 00 class 0x0c0310
[    0.279422] pci 0001:00:12.1: reg 0x10: [mem 0x8008b000-0x8008bfff]
[    0.279583] pci 0001:00:12.1: supports D1 D2
[    0.279624] pci 0001:00:12.1: PME# supported from D0 D1 D2 D3hot
[    0.281901] pci 0001:00:12.2: [1033:00e0] type 00 class 0x0c0320
[    0.281986] pci 0001:00:12.2: reg 0x10: [mem 0x80081000-0x800810ff]
[    0.282146] pci 0001:00:12.2: supports D1 D2
[    0.282188] pci 0001:00:12.2: PME# supported from D0 D1 D2 D3hot
[    0.283762] pci 0001:00:13.0: [1095:3112] type 00 class 0x018000
[    0.283842] pci 0001:00:13.0: reg 0x10: [io  0x0460-0x0467]
[    0.283898] pci 0001:00:13.0: reg 0x14: [io  0x0450-0x0453]
[    0.283953] pci 0001:00:13.0: reg 0x18: [io  0x0440-0x0447]
[    0.284007] pci 0001:00:13.0: reg 0x1c: [io  0x0430-0x0433]
[    0.284061] pci 0001:00:13.0: reg 0x20: [io  0x0420-0x042f]
[    0.284116] pci 0001:00:13.0: reg 0x24: [mem 0x80082000-0x800821ff]
[    0.284173] pci 0001:00:13.0: reg 0x30: [mem 0x80100000-0x8017ffff pref]
[    0.284291] pci 0001:00:13.0: supports D1 D2
[    0.286575] pci 0001:00:15.0: [9710:9865] type 00 class 0x070002
[    0.286660] pci 0001:00:15.0: reg 0x10: [io  0x0410-0x0417]
[    0.286718] pci 0001:00:15.0: reg 0x14: [mem 0x8008a000-0x8008afff]
[    0.286790] pci 0001:00:15.0: reg 0x20: [mem 0x80089000-0x80089fff]
[    0.286924] pci 0001:00:15.0: supports D1 D2
[    0.286966] pci 0001:00:15.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.288641] pci 0001:00:15.1: [9710:9865] type 00 class 0x070002
[    0.288726] pci 0001:00:15.1: reg 0x10: [io  0x0400-0x0407]
[    0.288784] pci 0001:00:15.1: reg 0x14: [mem 0x80088000-0x80088fff]
[    0.288856] pci 0001:00:15.1: reg 0x20: [mem 0x80087000-0x80087fff]
[    0.288988] pci 0001:00:15.1: supports D1 D2
[    0.289030] pci 0001:00:15.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.291912] pci 0001:00:15.2: [ffff:9865] type 00 class 0x070103
[    0.292001] pci 0001:00:15.2: reg 0x10: [io  0x0000-0x0007]
[    0.292058] pci 0001:00:15.2: reg 0x14: [io  0x0000-0x0007]
[    0.292113] pci 0001:00:15.2: reg 0x18: [mem 0x00000000-0x00000fff]
[    0.292177] pci 0001:00:15.2: reg 0x20: [mem 0x00000000-0x00000fff]
[    0.292310] pci 0001:00:15.2: supports D1 D2
[    0.292352] pci 0001:00:15.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.293880] pci 0001:00:16.0: [14e4:4320] type 00 class 0x028000
[    0.293960] pci 0001:00:16.0: reg 0x10: [mem 0x8008e000-0x8008ffff]
[    0.294116] pci 0001:00:16.0: supports D1 D2
[    0.294158] pci 0001:00:16.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.296270] pci 0001:00:17.0: [106b:0022] type 00 class 0xff0000
[    0.296354] pci 0001:00:17.0: reg 0x10: [mem 0x80000000-0x8007ffff]
[    0.298233] pci 0001:00:18.0: [106b:0019] type 00 class 0x0c0310
[    0.298317] pci 0001:00:18.0: reg 0x10: [mem 0x80086000-0x80086fff]
[    0.300550] pci 0001:00:19.0: [106b:0019] type 00 class 0x0c0310
[    0.300633] pci 0001:00:19.0: reg 0x10: [mem 0x80085000-0x80085fff]
[    0.302908] pci 0001:00:1b.0: [1033:0035] type 00 class 0x0c0310
[    0.302994] pci 0001:00:1b.0: reg 0x10: [mem 0x80084000-0x80084fff]
[    0.303155] pci 0001:00:1b.0: supports D1 D2
[    0.303197] pci 0001:00:1b.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.305499] pci 0001:00:1b.1: [1033:0035] type 00 class 0x0c0310
[    0.305584] pci 0001:00:1b.1: reg 0x10: [mem 0x80083000-0x80083fff]
[    0.305745] pci 0001:00:1b.1: supports D1 D2
[    0.305787] pci 0001:00:1b.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.307464] pci 0001:00:1b.2: [1033:00e0] type 00 class 0x0c0320
[    0.307545] pci 0001:00:1b.2: reg 0x10: [mem 0x80080000-0x800800ff]
[    0.307703] pci 0001:00:1b.2: supports D1 D2
[    0.307746] pci 0001:00:1b.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.310140] pci_bus 0001:00: busn_res: [bus 00-ff] end is updated to 00
[    0.315797] PCI host bridge to bus 0002:00
[    0.315878] pci_bus 0002:00: root bus resource [io  0x880000-0x107ffff] (bus address [0x0000-0x7fffff])
[    0.315955] pci_bus 0002:00: root bus resource [mem 0xf5000000-0xf5ffffff]
[    0.316021] pci_bus 0002:00: root bus resource [bus 00-ff]
[    0.316071] pci_bus 0002:00: busn_res: [bus 00-ff] end is updated to ff
[    0.317732] pci 0002:00:0b.0: [106b:0036] type 00 class 0x060000
[    0.320007] pci 0002:00:0d.0: [106b:0033] type 00 class 0xff0000
[    0.320089] pci 0002:00:0d.0: reg 0x10: [mem 0xf5004000-0xf5007fff]
[    0.322362] pci 0002:00:0e.0: [106b:0031] type 00 class 0x0c0010
[    0.322446] pci 0002:00:0e.0: reg 0x10: [mem 0xf5000000-0xf5000fff]
[    0.322599] pci 0002:00:0e.0: supports D1 D2
[    0.322641] pci 0002:00:0e.0: PME# supported from D0 D1 D2 D3hot
[    0.324813] pci 0002:00:0f.0: [106b:0032] type 00 class 0x020000
[    0.324896] pci 0002:00:0f.0: reg 0x10: [mem 0xf5200000-0xf53fffff]
[    0.324998] pci 0002:00:0f.0: reg 0x30: [mem 0xf5100000-0xf51fffff pref]
[    0.328339] pci_bus 0002:00: busn_res: [bus 00-ff] end is updated to 00
[    0.329852] PCI 0000:00 Cannot reserve Legacy IO [io  0xff780000-0xff780fff]
[    0.329933] PCI 0001:00 Cannot reserve Legacy IO [io  0x0000-0x0fff]
[    0.330011] pci_bus 0000:00: resource 4 [io  0xff780000-0xfff7ffff]
[    0.330064] pci_bus 0000:00: resource 5 [mem 0xf1000000-0xf1ffffff]
[    0.330113] pci_bus 0000:00: resource 6 [mem 0x90000000-0xafffffff]
[    0.330231] pci 0001:00:15.2: BAR 2: assigned [mem 0xf3000000-0xf3000fff]
[    0.330295] pci 0001:00:15.2: BAR 4: assigned [mem 0xf3001000-0xf3001fff]
[    0.330356] pci 0001:00:15.2: BAR 0: assigned [io  0x1000-0x1007]
[    0.330413] pci 0001:00:15.2: BAR 1: assigned [io  0x1008-0x100f]
[    0.330490] pci_bus 0001:00: resource 4 [io  0x0000-0x7fffff]
[    0.330538] pci_bus 0001:00: resource 5 [mem 0xf3000000-0xf3ffffff]
[    0.330587] pci_bus 0001:00: resource 6 [mem 0x80000000-0x8fffffff]
[    0.330642] pci_bus 0002:00: resource 4 [io  0x880000-0x107ffff]
[    0.330690] pci_bus 0002:00: resource 5 [mem 0xf5000000-0xf5ffffff]
[    0.407978] raid6: altivecx8 gen()   551 MB/s
[    0.464843] raid6: altivecx4 gen()   535 MB/s
[    0.521736] raid6: altivecx2 gen()   476 MB/s
[    0.578586] raid6: altivecx1 gen()   385 MB/s
[    0.635454] raid6: int32x8  gen()   140 MB/s
[    0.692319] raid6: int32x4  gen()   134 MB/s
[    0.749206] raid6: int32x2  gen()   117 MB/s
[    0.806068] raid6: int32x1  gen()    94 MB/s
[    0.806106] raid6: using algorithm altivecx8 gen() 551 MB/s
[    0.806143] raid6: using intx1 recovery algorithm
[    0.819558] SCSI subsystem initialized
[    0.822959] libata version 3.00 loaded.
[    0.825121] usbcore: registered new interface driver usbfs
[    0.825681] usbcore: registered new interface driver hub
[    0.827042] usbcore: registered new device driver usb
[    0.844523] pci 0000:00:10.0: vgaarb: setting as boot VGA device
[    0.844606] pci 0000:00:10.0: vgaarb: bridge control possible
[    0.844649] pci 0000:00:10.0: vgaarb: VGA device added: decodes=io+mem,owns=mem,locks=none
[    0.844764] vgaarb: loaded
[    0.846311] clocksource: Switched to clocksource timebase
[    0.980338] NET: Registered PF_INET protocol family
[    0.983477] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.993218] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 10240 bytes, linear)
[    0.997881] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.999688] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    1.009250] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear)
[    1.011623] TCP: Hash tables configured (established 8192 bind 8192)
[    1.014929] UDP hash table entries: 512 (order: 2, 24576 bytes, linear)
[    1.015770] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes, linear)
[    1.017911] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    1.019516] pci 0001:00:12.0: enabling device (0000 -> 0002)
[    1.019846] pci 0001:00:12.1: enabling device (0000 -> 0002)
[    1.019990] pci 0001:00:12.2: enabling device (0004 -> 0006)
[    1.020263] Apple USB OHCI 0001:00:18.0 disabled by firmware
[    1.020308] pci 0001:00:18.0: Can't enable PCI device, BIOS handoff failed.
[    1.020378] Apple USB OHCI 0001:00:19.0 disabled by firmware
[    1.020417] pci 0001:00:19.0: Can't enable PCI device, BIOS handoff failed.
[    1.020496] pci 0001:00:1b.0: enabling device (0000 -> 0002)
[    1.020623] pci 0001:00:1b.1: enabling device (0000 -> 0002)
[    1.020823] pci 0001:00:1b.2: enabling device (0004 -> 0006)
[    1.021019] pci 0002:00:0f.0: CLS mismatch (32 != 1020), using 32 bytes
[    1.028670] Thermal assist unit not available
[    1.043106] Initialise system trusted keyrings
[    1.045126] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[    1.073240] fuse: init (API version 7.38)
[    1.076129] 9p: Installing v9fs 9p2000 file system support
[    1.078364] NET: Registered PF_ALG protocol family
[    1.078717] xor: measuring software checksum speed
[    1.156549]    8regs           :   126 MB/sec
[    1.234996]    8regs_prefetch  :   125 MB/sec
[    1.314093]    32regs          :   124 MB/sec
[    1.394324]    32regs_prefetch :   122 MB/sec
[    1.414167]    altivec         :   496 MB/sec
[    1.414205] xor: using function: altivec (496 MB/sec)
[    1.414352] Key type asymmetric registered
[    1.414396] Asymmetric key parser 'x509' registered
[    1.443821] bounce: pool size: 64 pages
[    1.445733] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.445803] io scheduler kyber registered
[    1.446444] io scheduler bfq registered
[    1.477722] MacIO PCI driver attached to Keylargo chipset
[    1.501607] 0.00013020:ch-a: ttyS0 at MMIO 0x80013020 (irq = 22, base_baud = 230400) is a Z85c30 ESCC - Serial port
[    1.511249] 0.00013000:ch-b: ttyS1 at MMIO 0x80013000 (irq = 23, base_baud = 230400) is a Z85c30 ESCC - Serial port
[    1.533326] sata_sil 0001:00:13.0: version 2.4
[    1.534186] sata_sil 0001:00:13.0: enabling device (0004 -> 0007)
[    1.546626] scsi host0: sata_sil
[    1.554535] scsi host1: sata_sil
[    1.557347] ata1: SATA max UDMA/100 mmio m512@0x80082000 tf 0x80082080 irq 53
[    1.557413] ata2: SATA max UDMA/100 mmio m512@0x80082000 tf 0x800820c0 irq 53
[    1.560006] pata-pci-macio 0002:00:0d.0: enabling device (0004 -> 0006)
[    1.576396] pata-pci-macio 0002:00:0d.0: Activating pata-macio chipset UniNorth ATA-6, Apple bus ID 3
[    1.586098] scsi host2: pata_macio
[    1.589267] ata3: PATA max UDMA/100 irq 39
[    1.869744] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[    1.870657] ata1.00: ATA-9: SanDisk SSD PLUS 240GB, UF4500RL, max UDMA/133
[    1.870718] ata1.00: 468877312 sectors, multi 1: LBA48 NCQ (depth 0/32)
[    1.872251] ata1.00: Features: Dev-Sleep
[    1.896726] ata1.00: configured for UDMA/100
[    1.898287] scsi 0:0:0:0: Direct-Access     ATA      SanDisk SSD PLUS 00RL PQ: 0 ANSI: 5
[    1.910083] sd 0:0:0:0: [sda] 468877312 512-byte logical blocks: (240 GB/224 GiB)
[    1.910369] sd 0:0:0:0: [sda] Write Protect is off
[    1.910446] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.910812] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.911498] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[    1.922464]  sda: [mac] sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8
[    1.937625] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.336351] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[    2.376558] ata2.00: ATA-9: WDC WD5000LPLX-60ZNTT1, 02.01A02, max UDMA/133
[    2.376620] ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[    2.379290] ata2.00: configured for UDMA/100
[    2.380451] scsi 1:0:0:0: Direct-Access     ATA      WDC WD5000LPLX-6 1A02 PQ: 0 ANSI: 5
[    2.389422] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[    2.389531] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[    2.389834] sd 1:0:0:0: [sdb] Write Protect is off
[    2.389912] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    2.390462] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.390977] sd 1:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes
[    2.423820]  sdb: [mac] sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8
[    2.438853] sd 1:0:0:0: [sdb] Attached SCSI disk
[    2.623019] pata-macio 0.0001f000:ata-4: Activating pata-macio chipset KeyLargo ATA-4, Apple bus ID 2
[    2.633905] scsi host3: pata_macio
[    2.636692] ata4: PATA max UDMA/66 irq 19
[    2.795731] ata4.00: CFA: DeLOCK 54143 512MB, 100511E, max UDMA/66
[    2.795806] ata4.00: 1009008 sectors, multi 1: LBA 
[    2.800505] scsi 3:0:0:0: Direct-Access     ATA      DeLOCK 54143 512 11E  PQ: 0 ANSI: 5
[    2.809061] sd 3:0:0:0: [sdc] 1009008 512-byte logical blocks: (517 MB/493 MiB)
[    2.809532] sd 3:0:0:0: [sdc] Write Protect is off
[    2.809652] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[    2.810043] sd 3:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    2.810562] sd 3:0:0:0: [sdc] Preferred minimum I/O size 512 bytes
[    2.821207]  sdc: [mac] sdc1 sdc2 sdc3 sdc4 sdc5 sdc6
[    2.834850] sd 3:0:0:0: [sdc] Attached SCSI disk
[    3.663043] pata-macio 0.00020000:ata-3: Activating pata-macio chipset KeyLargo ATA-3, Apple bus ID 0
[    3.673068] scsi host4: pata_macio
[    3.675771] ata5: PATA max MWDMA2 irq 20
[    3.677845] tun: Universal TUN/TAP device driver, 1.6
[    3.681139] sungem.c:v1.0 David S. Miller <davem@redhat.com>
[    3.693839] gem 0002:00:0f.0 eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0a:95:9c:76:3a
[    3.698326] ehci-pci 0001:00:12.2: EHCI Host Controller
[    3.698536] ehci-pci 0001:00:12.2: new USB bus registered, assigned bus number 1
[    3.700480] ehci-pci 0001:00:12.2: irq 52, io mem 0x80081000
[    3.705746] rtc-generic rtc-generic: registered as rtc0
[    3.708396] PowerMac i2c bus pmu 2 registered
[    3.710461] PowerMac i2c bus pmu 1 registered
[    3.713089] ehci-pci 0001:00:12.2: USB 2.0 started, EHCI 1.00
[    3.715017] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[    3.715094] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.715147] usb usb1: Product: EHCI Host Controller
[    3.715187] usb usb1: Manufacturer: Linux 6.5.0-rc5-PMacG4 ehci_hcd
[    3.715231] usb usb1: SerialNumber: 0001:00:12.2
[    3.719159] PowerMac i2c bus mac-io 0 registered
[    3.720124] hub 1-0:1.0: USB hub found
[    3.720320] i2c i2c-2: No i2c address for /pci@f2000000/mac-io@17/i2c@18000/i2c-modem
[    3.720416] hub 1-0:1.0: 5 ports detected
[    3.722255] PowerMac i2c bus uni-n 1 registered
[    3.722338] i2c i2c-3: i2c-powermac: modalias failure on /uni-n@f8000000/i2c@f8001000/cereal@1c0
[    3.724765] PowerMac i2c bus uni-n 0 registered
[    3.729485] ehci-pci 0001:00:1b.2: EHCI Host Controller
[    3.729716] ehci-pci 0001:00:1b.2: new USB bus registered, assigned bus number 2
[    3.730612] ehci-pci 0001:00:1b.2: irq 63, io mem 0x80080000
[    3.733413] hid: raw HID events driver (C) Jiri Kosina
[    3.736785] usbcore: registered new interface driver usbhid
[    3.736843] usbhid: USB HID core driver
[    3.743027] ehci-pci 0001:00:1b.2: USB 2.0 started, EHCI 1.00
[    3.743279] NET: Registered PF_INET6 protocol family
[    3.745008] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[    3.745093] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.745146] usb usb2: Product: EHCI Host Controller
[    3.745187] usb usb2: Manufacturer: Linux 6.5.0-rc5-PMacG4 ehci_hcd
[    3.745230] usb usb2: SerialNumber: 0001:00:1b.2
[    3.750859] hub 2-0:1.0: USB hub found
[    3.751151] hub 2-0:1.0: 5 ports detected
[    3.757357] Segment Routing with IPv6
[    3.758020] In-situ OAM (IOAM) with IPv6
[    3.758553] NET: Registered PF_PACKET protocol family
[    3.758639] NET: Registered PF_KEY protocol family
[    3.760672] 9pnet: Installing 9P2000 support
[    3.764067] drmem: No dynamic reconfiguration memory found
[    3.832304] ata5.00: ATAPI: _NEC DVD_RW ND-3520A, 1.04, max UDMA/33
[    3.841161] scsi 4:0:0:0: CD-ROM            _NEC     DVD_RW ND-3520A  1.04 PQ: 0 ANSI: 5
[    3.933847] Loading compiled-in X.509 certificates
[    3.978173] usb 1-3: new high-speed USB device number 2 using ehci-pci
[    3.984465] sr 4:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[    3.984578] cdrom: Uniform CD-ROM driver Revision: 3.20
[    4.014561] sr 4:0:0:0: Attached scsi CD-ROM sr0
[    4.029466] zswap: loaded using pool zstd/z3fold
[    4.130073] usb 1-3: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=32.98
[    4.130187] usb 1-3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    4.130236] usb 1-3: Product: USB2.0 Hub
[    4.134972] hub 1-3:1.0: USB hub found
[    4.135634] hub 1-3:1.0: 4 ports detected
[    4.158873] debug_vm_pgtable: [debug_vm_pgtable         ]: Validating architecture page table helpers
[    4.273749] Btrfs loaded, zoned=no, fsverity=no
[    4.433066] usb 1-3.1: new low-speed USB device number 3 using ehci-pci
[    4.569422] usb 1-3.1: New USB device found, idVendor=04d9, idProduct=0006, bcdDevice= 1.40
[    4.569505] usb 1-3.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.569558] usb 1-3.1: Product: RPI Wired Keyboard 5
[    4.569599] usb 1-3.1: Manufacturer:  
[    4.607593] input:   RPI Wired Keyboard 5 as /devices/pci0001:00/0001:00:12.2/usb1/1-3/1-3.1/1-3.1:1.0/0003:04D9:0006.0001/input/input0
[    4.683327] hid-generic 0003:04D9:0006.0001: input,hidraw0: USB HID v1.11 Keyboard [  RPI Wired Keyboard 5] on usb-0001:00:12.2-3.1/input0
[    4.715682] input:   RPI Wired Keyboard 5 as /devices/pci0001:00/0001:00:12.2/usb1/1-3/1-3.1/1-3.1:1.1/0003:04D9:0006.0002/input/input1
[    4.777645] hid-generic 0003:04D9:0006.0002: input,hidraw1: USB HID v1.11 Device [  RPI Wired Keyboard 5] on usb-0001:00:12.2-3.1/input1
[    4.866911] usb 1-3.4: new low-speed USB device number 4 using ehci-pci
[    4.975544] usb 1-3.4: New USB device found, idVendor=275d, idProduct=0ba6, bcdDevice= 1.00
[    4.975623] usb 1-3.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    4.975676] usb 1-3.4: Product: USB OPTICAL MOUSE 
[    4.998822] input: USB OPTICAL MOUSE  as /devices/pci0001:00/0001:00:12.2/usb1/1-3/1-3.4/1-3.4:1.0/0003:275D:0BA6.0003/input/input2
[    5.010038] hid-generic 0003:275D:0BA6.0003: input,hidraw2: USB HID v1.11 Mouse [USB OPTICAL MOUSE ] on usb-0001:00:12.2-3.4/input0
[   10.209880] input: PMU as /devices/virtual/input/input3
[   10.212078] netpoll: netconsole: local port 6666
[   10.212131] netpoll: netconsole: local IPv4 address 192.168.178.8
[   10.212178] netpoll: netconsole: interface 'eth0'
[   10.212212] netpoll: netconsole: remote port 6666
[   10.212245] netpoll: netconsole: remote IPv4 address 192.168.178.3
[   10.212286] netpoll: netconsole: remote ethernet address 70:85:c2:30:ec:01
[   10.212337] netpoll: netconsole: device eth0 not up yet, forcing it
[   10.320067] sungem_phy: PHY ID: 2060e1, addr: 0
[   10.320379] gem 0002:00:0f.0 eth0: Found BCM5421 PHY
[   13.983328] gem 0002:00:0f.0 eth0: Link is up at 1000 Mbps, full-duplex
[   13.983532] gem 0002:00:0f.0 eth0: Pause is enabled (rxfifo: 10240 off: 7168 on: 5632)
[   13.994699] printk: console [netcon0] enabled
[   14.036498] netconsole: network logging started
[   14.239403] EXT4-fs (sda5): mounted filesystem 28419c7c-4bc4-4922-bdc8-6d8515c62385 ro with ordered data mode. Quota mode: disabled.
[   14.239990] VFS: Mounted root (ext4 filesystem) readonly on device 8:5.
[   14.244715] devtmpfs: mounted
[   14.249518] Freeing unused kernel image (initmem) memory: 1344K
[   14.276783] Checked W+X mappings: passed, no W+X pages found
[   14.276983] rodata_test: all tests were successful
[   14.277099] kallsyms_selftest: start
[   14.277149] Run /usr/lib/systemd/systemd as init process
[   14.277335]   with arguments:
[   14.277413]     /usr/lib/systemd/systemd
[   14.277491]   with environment:
[   14.277590]     HOME=/
[   14.277689]     TERM=linux
[   15.120401] systemd[1]: systemd 253 running in system mode (+PAM -AUDIT -SELINUX -APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID -CURL +ELFUTILS -FIDO2 +IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 +LZ4 -XZ -ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP -SYSVINIT default-hierarchy=unified)
[   15.120838] systemd[1]: Detected architecture ppc.
[   15.148550] systemd[1]: Hostname set to <T600>.
[   15.481699] memfd_create() without MFD_EXEC nor MFD_NOEXEC_SEAL, pid=1 'systemd'
[   18.124530] systemd[1]: Queued start job for default target graphical.target.
[   18.345048] systemd[1]: Created slice system-getty.slice.
[   18.361401] systemd[1]: Created slice system-modprobe.slice.
[   18.375829] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[   18.389710] systemd[1]: Created slice system-vncserver.slice.
[   18.403334] systemd[1]: Created slice user.slice.
[   18.409130] systemd[1]: Started systemd-ask-password-console.path.
[   18.414424] systemd[1]: Started systemd-ask-password-wall.path.
[   18.426596] systemd[1]: Set up automount proc-sys-fs-binfmt_misc.automount.
[   18.428408] systemd[1]: Reached target paths.target.
[   18.429697] systemd[1]: Reached target remote-fs.target.
[   18.431594] systemd[1]: Reached target slices.target.
[   18.457162] systemd[1]: Listening on systemd-coredump.socket.
[   18.466663] systemd[1]: Listening on systemd-journald-dev-log.socket.
[   18.474897] systemd[1]: Listening on systemd-journald.socket.
[   18.485886] systemd[1]: Listening on systemd-udevd-control.socket.
[   18.493976] systemd[1]: Listening on systemd-udevd-kernel.socket.
[   18.502485] systemd[1]: dev-hugepages.mount was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/mm/hugepages).
[   18.536705] systemd[1]: Mounting dev-mqueue.mount...
[   18.608886] systemd[1]: Mounting sys-kernel-debug.mount...
[   18.616610] systemd[1]: sys-kernel-tracing.mount was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/tracing).
[   18.705204] systemd[1]: Starting kmod-static-nodes.service...
[   18.875307] systemd[1]: Starting modprobe@configfs.service...
[   18.942516] systemd[1]: Starting modprobe@dm_mod.service...
[   19.047957] systemd[1]: Starting modprobe@drm.service...
[   19.127904] device-mapper: uevent: version 1.0.3
[   19.139541] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[   19.141987] systemd[1]: Starting modprobe@fuse.service...
[   19.215507] systemd[1]: Starting modprobe@loop.service...
[   19.271772] systemd[1]: Starting systemd-fsck-root.service...
[   19.480028] systemd[1]: Starting systemd-journald.service...
[   19.531564] loop: module loaded
[   19.612769] systemd[1]: Starting systemd-modules-load.service...
[   19.729038] systemd[1]: Starting systemd-udev-trigger.service...
[   20.046606] systemd-journald[106]: Collecting audit messages is disabled.
[   20.506731] systemd[1]: Mounted dev-mqueue.mount.
[   20.522564] systemd[1]: Mounted sys-kernel-debug.mount.
[   20.560225] systemd[1]: Finished kmod-static-nodes.service.
[   20.580080] systemd[1]: modprobe@configfs.service: Deactivated successfully.
[   20.589140] systemd[1]: Finished modprobe@configfs.service.
[   20.654332] systemd[1]: modprobe@dm_mod.service: Deactivated successfully.
[   20.658990] systemd[1]: Finished modprobe@dm_mod.service.
[   20.673207] systemd[1]: modprobe@drm.service: Deactivated successfully.
[   20.678336] systemd[1]: Finished modprobe@drm.service.
[   20.780497] systemd[1]: modprobe@fuse.service: Deactivated successfully.
[   20.793348] systemd[1]: Finished modprobe@fuse.service.
[   20.928175] systemd[1]: modprobe@loop.service: Deactivated successfully.
[   20.933559] systemd[1]: Finished modprobe@loop.service.
[   20.947757] systemd[1]: Finished systemd-fsck-root.service.
[   20.960051] systemd[1]: Finished systemd-modules-load.service.
[   21.197472] systemd[1]: Mounting sys-fs-fuse-connections.mount...
[   21.482474] systemd[1]: Mounting sys-kernel-config.mount...
[   21.628583] systemd[1]: Starting systemd-remount-fs.service...
[   21.683321] systemd[1]: systemd-repart.service was skipped because no trigger condition checks were met.
[   21.746142] systemd[1]: Starting systemd-sysctl.service...
[   21.949481] systemd[1]: Mounted sys-fs-fuse-connections.mount.
[   21.969580] systemd[1]: Mounted sys-kernel-config.mount.
[   22.523378] systemd[1]: Finished systemd-sysctl.service.
[   26.213920] EXT4-fs (sda5): re-mounted 28419c7c-4bc4-4922-bdc8-6d8515c62385 r/w. Quota mode: disabled.
[   26.284328] systemd[1]: Finished systemd-remount-fs.service.
[   26.288233] systemd[1]: systemd-firstboot.service was skipped because of an unmet condition check (ConditionFirstBoot=yes).
[   26.322115] systemd[1]: systemd-hwdb-update.service was skipped because of an unmet condition check (ConditionNeedsUpdate=/etc).
[   26.545743] systemd[1]: Starting systemd-random-seed.service...
[   26.557043] systemd[1]: systemd-sysusers.service was skipped because no trigger condition checks were met.
[   26.659307] systemd[1]: Starting systemd-tmpfiles-setup-dev.service...
[   27.172221] systemd[1]: Started systemd-journald.service.
[   27.636410] random: crng init done
[   27.660670] systemd-journald[106]: Received client request to flush runtime journal.
[   27.877326] systemd-journald[106]: /var/log/journal/71303955349d475c9d69360df5e2c5b5/system.journal: Monotonic clock jumped backwards relative to last journal entry, rotating.
[   27.877602] systemd-journald[106]: Rotating system journal.
[   43.112141] BTRFS: device label g4_musl devid 1 transid 64495 /dev/sda4 scanned by (udev-worker) (143)
[   43.617118] BTRFS: device label tmp devid 1 transid 40 /dev/sda6 scanned by (udev-worker) (127)
[   47.035392] gem 0002:00:0f.0 enP2p0s15: renamed from eth0 (while UP)
[   47.636141] kallsyms_selftest:  ---------------------------------------------------------
[   47.636452] kallsyms_selftest: | nr_symbols | compressed size | original size | ratio(%) |
[   47.636564] kallsyms_selftest: |---------------------------------------------------------|
[   47.636660] kallsyms_selftest: |      33861 |        364315   |       629849  |  57.84   |
[   47.636762] kallsyms_selftest:  ---------------------------------------------------------
[   48.203536] Adding 8388604k swap on /dev/sdb6.  Priority:-2 extents:1 across:8388604k FS
[   52.068658] kallsyms_selftest: kallsyms_lookup_name() looked up 33861 symbols
[   52.068880] kallsyms_selftest: The time spent on each symbol is (ns): min=6817, max=1222840, avg=98829
[   52.130101] kallsyms_selftest: kallsyms_on_each_symbol() traverse all: 61102994 ns
[   52.130459] kallsyms_selftest: kallsyms_on_each_match_symbol() traverse all: 84592 ns
[   52.130567] kallsyms_selftest: finish
[   52.687151] ohci-pci 0001:00:12.0: OHCI PCI host controller
[   52.687533] ohci-pci 0001:00:12.0: new USB bus registered, assigned bus number 3
[   52.688323] ohci-pci 0001:00:12.0: irq 52, io mem 0x8008c000
[   53.036643] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.05
[   53.036933] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   53.037082] usb usb3: Product: OHCI PCI host controller
[   53.037209] usb usb3: Manufacturer: Linux 6.5.0-rc5-PMacG4 ohci_hcd
[   53.037339] usb usb3: SerialNumber: 0001:00:12.0
[   53.095539] hub 3-0:1.0: USB hub found
[   53.103746] hub 3-0:1.0: 3 ports detected
[   53.161326] ohci-pci 0001:00:12.1: OHCI PCI host controller
[   53.161686] ohci-pci 0001:00:12.1: new USB bus registered, assigned bus number 4
[   53.183413] ohci-pci 0001:00:12.1: irq 52, io mem 0x8008b000
[   53.331120] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.05
[   53.331334] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   53.331448] usb usb4: Product: OHCI PCI host controller
[   53.331546] usb usb4: Manufacturer: Linux 6.5.0-rc5-PMacG4 ohci_hcd
[   53.331709] usb usb4: SerialNumber: 0001:00:12.1
[   53.477773] hub 4-0:1.0: USB hub found
[   53.536412] hub 4-0:1.0: 2 ports detected
[   53.569858] Apple USB OHCI 0001:00:18.0 disabled by firmware
[   53.570164] Apple USB OHCI 0001:00:19.0 disabled by firmware
[   53.570761] ohci-pci 0001:00:1b.0: OHCI PCI host controller
[   53.570982] ohci-pci 0001:00:1b.0: new USB bus registered, assigned bus number 5
[   53.571662] ohci-pci 0001:00:1b.0: irq 63, io mem 0x80084000
[   53.827596] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.05
[   53.827871] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   53.828017] usb usb5: Product: OHCI PCI host controller
[   53.828145] usb usb5: Manufacturer: Linux 6.5.0-rc5-PMacG4 ohci_hcd
[   53.828273] usb usb5: SerialNumber: 0001:00:1b.0
[   53.860978] hub 5-0:1.0: USB hub found
[   53.875830] hub 5-0:1.0: 3 ports detected
[   53.927687] BTRFS info (device sda6): using xxhash64 (xxhash64-generic) checksum algorithm
[   53.927967] BTRFS info (device sda6): use lzo compression, level 0
[   53.928131] BTRFS info (device sda6): using free space tree
[   54.102510] ohci-pci 0001:00:1b.1: OHCI PCI host controller
[   54.102857] ohci-pci 0001:00:1b.1: new USB bus registered, assigned bus number 6
[   54.111129] ohci-pci 0001:00:1b.1: irq 63, io mem 0x80083000
[   54.112810] BTRFS info (device sda6): enabling ssd optimizations
[   54.373705] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.05
[   54.373923] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   54.374040] usb usb6: Product: OHCI PCI host controller
[   54.374139] usb usb6: Manufacturer: Linux 6.5.0-rc5-PMacG4 ohci_hcd
[   54.374239] usb usb6: SerialNumber: 0001:00:1b.1
[   54.481742] hub 6-0:1.0: USB hub found
[   54.482227] hub 6-0:1.0: 2 ports detected
[   54.813029] EXT4-fs (sdc5): mounting ext2 file system using the ext4 subsystem
[   54.847293] EXT4-fs (sdc5): mounted filesystem e4e8af9e-0f0d-44f9-b983-71bf61d782de r/w without journal. Quota mode: disabled.
[   54.847676] ext2 filesystem being mounted at /boot supports timestamps until 2038-01-19 (0x7fffffff)
[   54.981052] b43-pci-bridge 0001:00:16.0: enabling device (0004 -> 0006)
[   54.981380] ssb: Found chip with id 0x4306, rev 0x02 and package 0x00
[   55.056814] b43-pci-bridge 0001:00:16.0: Sonics Silicon Backplane found on PCI device 0001:00:16.0
[   58.667252] firewire_ohci 0002:00:0e.0: enabling device (0000 -> 0002)
[   58.810017] firewire_ohci 0002:00:0e.0: added OHCI v1.10 device as card 0, 8 IR + 8 IT contexts, quirks 0x0
[   59.060044] [drm] radeon kernel modesetting enabled.
[   59.060648] radeon 0000:00:10.0: vgaarb: deactivate vga console
[   59.064079] radeon 0000:00:10.0: enabling device (0006 -> 0007)
[   59.068931] [drm] initializing kernel modesetting (RV350 0x1002:0x4150 0x1002:0x0002 0x00).
[   59.069164] [drm] Forcing AGP to PCI mode
[   59.070893] radeon 0000:00:10.0: Invalid PCI ROM header signature: expecting 0xaa55, got 0x0000
[   59.352404] ADM1030 fan controller [@2c]
[   59.377255] DS1775 digital thermometer [@49]
[   59.377493] Temp: 55.6 C
[   59.377513]   Hyst: 70.0 C
[   59.377633]   OS: 75.0 C
[   59.377752] 
[   59.763602] [drm] Generation 2 PCI interface, using max accessible memory
[   59.763874] radeon 0000:00:10.0: VRAM: 256M 0x00000000A0000000 - 0x00000000AFFFFFFF (256M used)
[   59.764326] radeon 0000:00:10.0: GTT: 512M 0x0000000080000000 - 0x000000009FFFFFFF
[   59.764634] [drm] Detected VRAM RAM=256M, BAR=256M
[   59.764734] [drm] RAM width 128bits DDR
[   59.780166] [drm] radeon: 256M of VRAM memory ready
[   59.780414] [drm] radeon: 512M of GTT memory ready.
[   59.780929] [drm] GART: num cpu pages 131072, num gpu pages 131072
[   60.113229] [drm] radeon: 1 quad pipes, 1 Z pipes initialized
[   60.113491] [drm] PCI GART of 512M enabled (table at 0x0000000009D00000).
[   60.113878] radeon 0000:00:10.0: WB enabled
[   60.114036] radeon 0000:00:10.0: fence driver on ring 0 use gpu addr 0x0000000080000000
[   60.137970] [drm] radeon: irq initialized.
[   60.138548] [drm] Loading R300 Microcode
[   60.579002] [drm] radeon: ring at 0x0000000080001000
[   60.579326] [drm] ring test succeeded in 1 usecs
[   60.680652] [drm] ib test succeeded in 0 usecs
[   61.083083] [drm] Radeon Display Connectors
[   61.083278] [drm] Connector 0:
[   61.083364] [drm]   DVI-I-1
[   61.083489] [drm]   HPD2
[   61.083576] [drm]   DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[   61.083677] [drm]   Encoders:
[   61.083759] [drm]     CRT1: INTERNAL_DAC1
[   61.083846] [drm]     DFP2: INTERNAL_DVO1
[   61.083987] [drm] Connector 1:
[   61.084073] [drm]   DVI-I-2
[   61.084153] [drm]   HPD1
[   61.084233] [drm]   DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[   61.084330] [drm]   Encoders:
[   61.084439] [drm]     CRT2: INTERNAL_DAC2
[   61.084525] [drm]     DFP1: INTERNAL_TMDS1
[   61.121961] [drm] Initialized radeon 2.50.0 20080528 for 0000:00:10.0 on minor 0
[   62.880807] [drm] fb mappable at 0xA0040000
[   62.881040] [drm] vram apper at 0xA0000000
[   62.881131] [drm] size 8294400
[   62.881285] [drm] fb depth is 24
[   62.881376] [drm]    pitch is 7680
[   63.159783] Console: switching to colour frame buffer device 240x67
[   63.848338] radeon 0000:00:10.0: [drm] fb0: radeondrmfb frame buffer device
[   67.493858] CPU-temp: 55.9 C
[   67.493913] , Case: 34.7 C
[   67.494419] ,  Fan: 0 (tuned -11)
[   74.316071] snd-aoa-fabric-layout: Using direct GPIOs
[   74.484924] snd-aoa-fabric-layout: can use this codec
[   74.565934] snd-aoa-codec-tas: tas found, addr 0x35 on /pci@f2000000/mac-io@17/i2c@18000/deq@6a
[   75.066404] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[   75.594139] CPU-temp: 56.1 C
[   75.594198] , Case: 34.7 C
[   75.594700] ,  Fan: 0 (tuned +0)
[   75.653538] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[   75.694369] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[   75.695612] cfg80211: failed to load regulatory.db
[   75.807277] systemd-journald[106]: /var/log/journal/71303955349d475c9d69360df5e2c5b5/user-1000.journal: Monotonic clock jumped backwards relative to last journal entry, rotating.
[   77.551538] b43legacy-phy0: Broadcom 4306 WLAN found (core revision 4)
[   77.596419] b43legacy-phy0 debug: Found PHY: Analog 1, Type 2, Revision 1
[   77.597452] b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
[   77.636464] b43legacy-phy0 debug: Radio initialized
[   77.638358] b43legacy-phy0: Loading firmware b43legacy/ucode4.fw
[   77.645456] Broadcom 43xx-legacy driver loaded [ Features: PLID ]
[   77.691775] b43legacy-phy0: Loading firmware b43legacy/pcm4.fw
[   77.765915] b43legacy-phy0: Loading firmware b43legacy/b0g0initvals2.fw
[   77.808827] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[  109.788321] EXT4-fs (sdc5): unmounting filesystem e4e8af9e-0f0d-44f9-b983-71bf61d782de.
[  111.685475] systemd-shutdown[1]: Syncing filesystems and block devices.
[  111.923236] systemd-shutdown[1]: Sending SIGTERM to remaining processes...
[  112.104740] systemd-journald[106]: Received SIGTERM from PID 1 (systemd-shutdow).
[  112.298064] systemd-shutdown[1]: Sending SIGKILL to remaining processes...
[  112.494375] systemd-shutdown[1]: Unmounting file systems.
[  112.540170] (sd-remount)[437]: Remounting '/' read-only with options ''.
[  112.601643] EXT4-fs (sda5): re-mounted 28419c7c-4bc4-4922-bdc8-6d8515c62385 ro. Quota mode: disabled.
[  112.915674] systemd-shutdown[1]: All filesystems unmounted.
[  112.948527] systemd-shutdown[1]: Deactivating swaps.
[  112.982083] systemd-shutdown[1]: All swaps deactivated.
[  113.015230] systemd-shutdown[1]: Detaching loop devices.
[  113.121619] systemd-shutdown[1]: All loop devices detached.
[  113.154169] systemd-shutdown[1]: Stopping MD devices.
[  113.231781] systemd-shutdown[1]: All MD devices stopped.
[  113.264338] systemd-shutdown[1]: Detaching DM devices.
[  113.298350] systemd-shutdown[1]: All DM devices detached.
[  113.331132] systemd-shutdown[1]: All filesystems, swaps, loop devices, MD devices and DM devices detached.
[  113.396235] systemd-shutdown[1]: Syncing filesystems and block devices.
[  113.430075] systemd-shutdown[1]: Powering off.
[  113.464089] sd 3:0:0:0: [sdc] Stopping disk
[  113.498360] sd 1:0:0:0: [sdb] Synchronizing SCSI cache
[  113.532334] sd 1:0:0:0: [sdb] Stopping disk
[  113.901349] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[  113.935089] sd 0:0:0:0: [sda] Stopping disk
[  113.979360] reboot: Power down

  reply	other threads:[~2023-08-13 19:40 UTC|newest]

Thread overview: 34+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-08-10 23:48 KASAN debug kernel fails to boot at early stage when CONFIG_SMP=y is set (kernel 6.5-rc5, PowerMac G4 3,6) Erhard Furtner
2023-08-11  6:45 ` Christophe Leroy
2023-08-13 19:38   ` Erhard Furtner [this message]
2023-08-14  9:40     ` Christophe Leroy
2023-08-14 17:27       ` Erhard Furtner
2023-08-15 17:21         ` [PATCH] Add pr_info() traces for investigation Christophe Leroy
2023-08-15 17:25         ` KASAN debug kernel fails to boot at early stage when CONFIG_SMP=y is set (kernel 6.5-rc5, PowerMac G4 3,6) Christophe Leroy
2023-08-15 20:01           ` Erhard Furtner
2023-08-16 15:56             ` Christophe Leroy
2023-08-17 18:32               ` Erhard Furtner
2023-08-17 23:13                 ` Michael Ellerman
2023-08-18  9:16                   ` Erhard Furtner
2023-08-18 15:47                     ` Christophe Leroy
2023-08-18 16:23                       ` Erhard Furtner
2023-08-22  7:31                         ` Christophe Leroy
2023-08-24  0:00                           ` Erhard Furtner
2023-08-24 11:36                             ` Michael Ellerman
2023-08-27 23:17                               ` Erhard Furtner
2023-08-31  5:32                                 ` Christophe Leroy
2023-08-31 22:44                                   ` Erhard Furtner
2023-09-01  7:43                                     ` Christophe Leroy
2023-09-03 21:06                                       ` Erhard Furtner
2023-09-04 14:48                                         ` Christophe Leroy
2023-09-04 14:55                                           ` Christophe Leroy
2023-09-04 21:32                                             ` Erhard Furtner
2023-09-12  0:11                                             ` Erhard Furtner
2023-09-12  7:47                                               ` Christophe Leroy
2023-09-12 15:59                                                 ` Erhard Furtner
2023-09-12 17:39                                                   ` Christophe Leroy
2023-09-12 20:09                                                     ` Erhard Furtner
2023-09-13  5:28                                                       ` Christophe Leroy
2023-09-14  4:54                                                     ` Christophe Leroy
2023-09-14 12:33                                                       ` Erhard Furtner
2024-02-28 23:55                                                       ` Erhard Furtner

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230813213855.794b3c8f@yea \
    --to=erhard_f@mailbox.org \
    --cc=christophe.leroy@csgroup.eu \
    --cc=linuxppc-dev@lists.ozlabs.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).