From: Erhard Furtner <erhard_f@mailbox.org>
To: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: "linuxppc-dev@lists.ozlabs.org" <linuxppc-dev@lists.ozlabs.org>
Subject: Re: KASAN debug kernel fails to boot at early stage when CONFIG_SMP=y is set (kernel 6.5-rc5, PowerMac G4 3,6)
Date: Tue, 15 Aug 2023 22:01:56 +0200 [thread overview]
Message-ID: <20230815220156.5c234b52@yea> (raw)
In-Reply-To: <6d710a2b-5cac-9f0a-cd30-0ad18172932b@csgroup.eu>
[-- Attachment #1: Type: text/plain, Size: 1091 bytes --]
On Tue, 15 Aug 2023 17:25:13 +0000
Christophe Leroy <christophe.leroy@csgroup.eu> wrote:
> I just sent a patch with additional pr_info() in order to help locate
> the issue, please provide output with that patch.
>
> Thanks
> Christophe
Thanks for your efforts Christophe! With the patch applied I get this output + a blank black line:
[ 0.000000] printk: bootconsole [udbg0] enabled
[ 0.000000] Total memory = 2048MB; using 4096kB for hash table
[ 0.000000] mapin_ram:125
[ 0.000000] mmu_mapin_ram:169 0 30000000 1400000 2000000
[ 0.000000] __mmu_mapin_ram:146 0 1400000
[ 0.000000] __mmu_mapin_ram:155 1400000
[ 0.000000] __mmu_mapin_ram:146 1400000 30000000
[ 0.000000] __mmu_mapin_ram:155 20000000
[ 0.000000] __mapin_ram_chunk:107 20000000 30000000
[ 0.000000] __mapin_ram_chunk:117
[ 0.000000] mapin_ram:134
[ 0.000000] btext_unmap:129
Afterwards the freeze. On a warm boot after booting another kernel the output continues with "[ 0.000000] btext_unmap:131" instead of the black line. Full dmesg of a warm boot attached.
Regards,
Erhard
[-- Attachment #2: dmesg_65-rc6_g4_01 --]
[-- Type: application/octet-stream, Size: 51082 bytes --]
[ 0.000000] printk: bootconsole [udbg0] enabled
[ 0.000000] Total memory = 2048MB; using 4096kB for hash table
[ 0.000000] mapin_ram:125
[ 0.000000] mmu_mapin_ram:169 0 30000000 1400000 2000000
[ 0.000000] __mmu_mapin_ram:146 0 1400000
[ 0.000000] __mmu_mapin_ram:155 1400000
[ 0.000000] __mmu_mapin_ram:146 1400000 30000000
[ 0.000000] __mmu_mapin_ram:155 20000000
[ 0.000000] __mapin_ram_chunk:107 20000000 30000000
[ 0.000000] __mapin_ram_chunk:117
[ 0.000000] mapin_ram:134
[ 0.000000] btext_unmap:129
[ 0.000000] btext_unmap:131
[ 0.000000] kasan_mmu_init:129
[ 0.000000] kasan_mmu_init:132 0
[ 0.000000] kasan_mmu_init:137
[ 0.000000] setup_kuap:23
[ 0.000000] setup_kuap:25
[ 0.000000] setup_kuap:30
[ 0.000000] setup_kuap:35
[ 0.000000] Activating Kernel Userspace Access Protection
[ 0.000000] setup_kuap:40
[ 0.000000] Activating Kernel Userspace Execution Prevention
[ 0.000000] Linux version 6.5.0-rc6-PMacG4-dirty (root@T1000) (gcc (Gentoo 12.3.1_p20230526 p2) 12.3.1 20230526, GNU ld (Gentoo 2.40 p7) 2.40.0) #4 SMP Tue Aug 15 21:44:33 CEST 2023
[ 0.000000] KASAN init done
[ 0.000000] ioremap() called early from pmac_feature_init+0x17c/0xe9c. Use early_ioremap() instead
[ 0.000000] Found UniNorth memory controller & host bridge @ 0xf8000000 revision: 0x24
[ 0.000000] Mapped at 0xf53bf000
[ 0.000000] ioremap() called early from probe_one_macio+0x1f8/0x400. Use early_ioremap() instead
[ 0.000000] Found a Keylargo mac-io controller, rev: 3, mapped at 0x(ptrval)
[ 0.000000] PowerMac motherboard: PowerMac G4 Windtunnel
[ 0.000000] ioremap() called early from btext_map+0x64/0xdc. Use early_ioremap() instead
[ 0.000000] Hardware name: PowerMac3,6 7455 0x80010303 PowerMac
[ 0.000000] CPU maps initialized for 1 thread per core
[ 0.000000] (thread shift is 0)
[ 0.000000] -----------------------------------------------------
[ 0.000000] phys_mem_size = 0x80000000
[ 0.000000] dcache_bsize = 0x20
[ 0.000000] icache_bsize = 0x20
[ 0.000000] cpu_features = 0x000000002514600a
[ 0.000000] possible = 0x00000000277de00a
[ 0.000000] always = 0x0000000001000000
[ 0.000000] cpu_user_features = 0x9c000001 0x00000000
[ 0.000000] mmu_features = 0x00010001
[ 0.000000] Hash_size = 0x400000
[ 0.000000] Hash_mask = 0xffff
[ 0.000000] -----------------------------------------------------
[ 0.000000] ioremap() called early from pmac_setup_arch+0x1ac/0x448. Use early_ioremap() instead
[ 0.000000] ioremap() called early from find_via_pmu+0x2a8/0x434. Use early_ioremap() instead
[ 0.000000] ioremap() called early from find_via_pmu+0x2e4/0x434. Use early_ioremap() instead
[ 0.000000] via-pmu: Server Mode is disabled
[ 0.000000] PMU driver v2 initialized for Core99, firmware: 0c
[ 0.000000] ioremap() called early from pmac_nvram_init+0x208/0x7c4. Use early_ioremap() instead
[ 0.000000] nvram: Checking bank 0...
[ 0.000000] nvram: gen0=3192, gen1=3193
[ 0.000000] nvram: Active bank is: 1
[ 0.000000] nvram: OF partition at 0x410
[ 0.000000] nvram: XP partition at 0x1020
[ 0.000000] nvram: NR partition at 0x1120
[ 0.000000] Top of RAM: 0x80000000, Total RAM: 0x80000000
[ 0.000000] Memory hole size: 0MB
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000] Normal empty
[ 0.000000] HighMem [mem 0x0000000030000000-0x000000007fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] percpu: Embedded 14 pages/cpu s24672 r8192 d24480 u57344
[ 0.000000] pcpu-alloc: s24672 r8192 d24480 u57344 alloc=14*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Kernel command line: ro root=/dev/sda5 zswap.max_pool_percent=16 slub_debug=FZP page_poison=1 netconsole=6666@192.168.178.8/eth0,6666@192.168.178.3/70:85:C2:30:EC:01 init=/usr/lib/systemd/systemd
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560
[ 0.000000] mem auto-init: stack:all(pattern), heap alloc:off, heap free:off
[ 0.000000] stackdepot: allocating hash table via alloc_large_system_hash
[ 0.000000] stackdepot hash table entries: 1048576 (order: 10, 4194304 bytes, linear)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xf6000000..0xfec00000 : kasan shadow mem
[ 0.000000] * 0xf5bbf000..0xf5fff000 : fixmap
[ 0.000000] * 0xf5400000..0xf5800000 : highmem PTEs
[ 0.000000] * 0xf5115000..0xf5400000 : early ioremap
[ 0.000000] * 0xf1000000..0xf5110000 : vmalloc & ioremap
[ 0.000000] * 0xb0000000..0xc0000000 : modules
[ 0.000000] Memory: 1946552K/2097152K available (16068K kernel code, 1964K rwdata, 4412K rodata, 1344K init, 402K bss, 150600K reserved, 0K cma-reserved, 1212416K highmem)
[ 0.000000] **********************************************************
[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.000000] ** **
[ 0.000000] ** This system shows unhashed kernel memory addresses **
[ 0.000000] ** via the console, logs, and other interfaces. This **
[ 0.000000] ** might reduce the security of your system. **
[ 0.000000] ** **
[ 0.000000] ** If you see this message and you are not debugging **
[ 0.000000] ** the kernel, report this immediately to your system **
[ 0.000000] ** administrator! **
[ 0.000000] ** **
[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.000000] **********************************************************
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[ 0.000000] NR_IRQS: 512, nr_irqs: 512, preallocated irqs: 16
[ 0.000000] mpic: Resetting
[ 0.000000] mpic: Setting up MPIC " MPIC 1 " version 1.2 at 80040000, max 2 CPUs
[ 0.000000] mpic: ISU size: 64, shift: 6, mask: 3f
[ 0.000000] mpic: Initializing for 64 sources
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] time_init: decrementer frequency = 41.658676 MHz
[ 0.000000] time_init: processor frequency = 1416.666661 MHz
[ 0.000010] clocksource: timebase: mask: 0xffffffffffffffff max_cycles: 0x99b9699db, max_idle_ns: 440795204297 ns
[ 0.000565] clocksource: timebase mult[18012db2] shift[24] registered
[ 0.001067] clockevent: decrementer mult[aaa249b] shift[32] cpu[0]
[ 0.003968] Console: colour dummy device 80x25
[ 0.004500] printk: console [tty0] enabled
[ 0.004961] printk: bootconsole [udbg0] disabled
[ 0.006157] pid_max: default: 32768 minimum: 301
[ 0.012492] LSM: initializing lsm=capability,yama
[ 0.012588] Yama: becoming mindful.
[ 0.014609] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.014806] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.030819] PowerMac SMP probe found 2 cpus
[ 0.031667] KeyWest i2c @0xf8001003 irq 42 /uni-n@f8000000/i2c@f8001000
[ 0.031841] channel 0 bus <multibus>
[ 0.031958] channel 1 bus <multibus>
[ 0.032333] KeyWest i2c @0x80018000 irq 26 /pci@f2000000/mac-io@17/i2c@18000
[ 0.032491] channel 0 bus <multibus>
[ 0.032631] PMU i2c /pci@f2000000/mac-io@17/via-pmu@16000/pmu-i2c
[ 0.032780] channel 1 bus <multibus>
[ 0.032893] channel 2 bus <multibus>
[ 0.032966] pmf: no parser for command 17 !
[ 0.033132] Processor timebase sync using GPIO 0x73
[ 0.033168] mpic: requesting IPIs...
[ 0.033540] CPU0: L2CR is 80000000
[ 0.033572] CPU0: L3CR is 9c030000
[ 0.039870] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1.
[ 0.041184] MPC7450 family performance monitor hardware support registered
[ 0.042195] rcu: Hierarchical SRCU implementation.
[ 0.042246] rcu: Max phase no-delay instances is 1000.
[ 0.045277] smp: Bringing up secondary CPUs ...
[84919679.112252] setup_kuap:23
[84919679.112337] setup_kuap:25
[84919679.112370] setup_kuap:30
[84919679.112414] CPU1: L2CR was 0
[84919679.112460] CPU1: L2CR set to 80000000
[84919679.112472] CPU1: L3CR was 0
[84919679.112622] CPU1: L3CR set to 9c030000
[ 0.052117] smp: Brought up 1 node, 2 CPUs
[ 0.058144] devtmpfs: initialized
[ 0.062059] Duplicate name in PowerPC,G4@0, renamed to "l2-cache#1"
[ 0.062637] Duplicate name in l2-cache#1, renamed to "l2-cache#1"
[ 0.065135] Duplicate name in PowerPC,G4@1, renamed to "l2-cache#1"
[ 0.065702] Duplicate name in l2-cache#1, renamed to "l2-cache#1"
[ 0.093318] Duplicate name in gpio@50, renamed to "gpio5@6f#1"
[ 0.093746] Duplicate name in gpio@50, renamed to "gpio6@70#1"
[ 0.094693] Duplicate name in gpio@50, renamed to "gpio11@75#1"
[ 0.095269] Duplicate name in gpio@50, renamed to "extint-gpio15@67#1"
[ 0.134341] Found UniNorth PCI host bridge at 0x00000000f0000000. Firmware bus number: 0->0
[ 0.134451] PCI host bridge /pci@f0000000 ranges:
[ 0.134554] MEM 0x00000000f1000000..0x00000000f1ffffff -> 0x00000000f1000000
[ 0.134632] IO 0x00000000f0000000..0x00000000f07fffff -> 0x0000000000000000
[ 0.155099] MEM 0x0000000090000000..0x00000000afffffff -> 0x0000000090000000
[ 0.155506] Found UniNorth PCI host bridge at 0x00000000f2000000. Firmware bus number: 0->0
[ 0.155568] PCI host bridge /pci@f2000000 (primary) ranges:
[ 0.155666] MEM 0x00000000f3000000..0x00000000f3ffffff -> 0x00000000f3000000
[ 0.155801] IO 0x00000000f2000000..0x00000000f27fffff -> 0x0000000000000000
[ 0.176330] MEM 0x0000000080000000..0x000000008fffffff -> 0x0000000080000000
[ 0.177310] Found UniNorth PCI host bridge at 0x00000000f4000000. Firmware bus number: 0->0
[ 0.177378] PCI host bridge /pci@f4000000 ranges:
[ 0.177476] MEM 0x00000000f5000000..0x00000000f5ffffff -> 0x00000000f5000000
[ 0.177541] IO 0x00000000f4000000..0x00000000f47fffff -> 0x0000000000000000
[ 0.198412] Found NEC PD720100A USB2 chip with disabled EHCI, fixing up...
[ 0.200576] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.200957] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.203545] prandom: seed boundary self test passed
[ 0.211726] prandom: 100 self tests passed
[ 0.219595] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.256623] PCI: Probing PCI hardware
[ 0.259492] PCI host bridge to bus 0000:00
[ 0.259574] pci_bus 0000:00: root bus resource [io 0xff780000-0xfff7ffff] (bus address [0x0000-0x7fffff])
[ 0.259658] pci_bus 0000:00: root bus resource [mem 0xf1000000-0xf1ffffff]
[ 0.259723] pci_bus 0000:00: root bus resource [mem 0x90000000-0xafffffff]
[ 0.259897] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.259954] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to ff
[ 0.261692] pci 0000:00:0b.0: [106b:0034] type 00 class 0x060000
[ 0.264079] pci 0000:00:10.0: [1002:4150] type 00 class 0x030000
[ 0.264171] pci 0000:00:10.0: reg 0x10: [mem 0xa0000000-0xafffffff pref]
[ 0.264237] pci 0000:00:10.0: reg 0x14: [io 0xff780400-0xff7804ff]
[ 0.264299] pci 0000:00:10.0: reg 0x18: [mem 0x90000000-0x9000ffff]
[ 0.264386] pci 0000:00:10.0: reg 0x30: [mem 0x90020000-0x9003ffff pref]
[ 0.264515] pci 0000:00:10.0: supports D1 D2
[ 0.268442] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.271184] OF: /pci@f2000000/mac-io@17/gpio@50/gpio5@6f: could not find phandle 1751474532
[ 0.271366] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio15@67: could not find phandle 1751474532
[ 0.271564] OF: /pci@f2000000/mac-io@17/gpio@50/gpio6@70: could not find phandle 1634562093
[ 0.271733] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio16@68: could not find phandle 1936745825
[ 0.271934] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio14@66: could not find phandle 1818848869
[ 0.272189] OF: /pci@f2000000/mac-io@17/gpio@50/gpio12@76: could not find phandle 1835103092
[ 0.272356] OF: /pci@f2000000/mac-io@17/gpio@50/gpio11@75: could not find phandle 1635083369
[ 0.272508] OF: /pci@f2000000/mac-io@17/gpio@50/gpio5@6f: could not find phandle 1751474532
[ 0.272658] OF: /pci@f2000000/mac-io@17/gpio@50/gpio6@70: could not find phandle 1634562093
[ 0.272808] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio4@5c: could not find phandle 1818848869
[ 0.273002] OF: /pci@f2000000/mac-io@17/gpio@50/gpio11@75: could not find phandle 1635083369
[ 0.273153] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio15@67: could not find phandle 1751474532
[ 0.276618] pci_bus 0001:00: Fixed dependency cycle(s) with /pci@f2000000/mac-io@17/interrupt-controller@40000
[ 0.276907] PCI host bridge to bus 0001:00
[ 0.276962] pci_bus 0001:00: root bus resource [io 0x0000-0x7fffff]
[ 0.277027] pci_bus 0001:00: root bus resource [mem 0xf3000000-0xf3ffffff]
[ 0.277091] pci_bus 0001:00: root bus resource [mem 0x80000000-0x8fffffff]
[ 0.277158] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.277209] pci_bus 0001:00: busn_res: [bus 00-ff] end is updated to ff
[ 0.278900] pci 0001:00:0b.0: [106b:0035] type 00 class 0x060000
[ 0.281835] pci 0001:00:12.0: [1033:0035] type 00 class 0x0c0310
[ 0.281923] pci 0001:00:12.0: reg 0x10: [mem 0x8008c000-0x8008cfff]
[ 0.282088] pci 0001:00:12.0: supports D1 D2
[ 0.282189] pci 0001:00:12.0: PME# supported from D0 D1 D2 D3hot
[ 0.284411] pci 0001:00:12.1: [1033:0035] type 00 class 0x0c0310
[ 0.284498] pci 0001:00:12.1: reg 0x10: [mem 0x8008b000-0x8008bfff]
[ 0.284662] pci 0001:00:12.1: supports D1 D2
[ 0.284705] pci 0001:00:12.1: PME# supported from D0 D1 D2 D3hot
[ 0.286973] pci 0001:00:12.2: [1033:00e0] type 00 class 0x0c0320
[ 0.287058] pci 0001:00:12.2: reg 0x10: [mem 0x80081000-0x800810ff]
[ 0.287220] pci 0001:00:12.2: supports D1 D2
[ 0.287263] pci 0001:00:12.2: PME# supported from D0 D1 D2 D3hot
[ 0.288823] pci 0001:00:13.0: [1095:3112] type 00 class 0x018000
[ 0.288930] pci 0001:00:13.0: reg 0x10: [io 0x0460-0x0467]
[ 0.288988] pci 0001:00:13.0: reg 0x14: [io 0x0450-0x0453]
[ 0.289044] pci 0001:00:13.0: reg 0x18: [io 0x0440-0x0447]
[ 0.289100] pci 0001:00:13.0: reg 0x1c: [io 0x0430-0x0433]
[ 0.289155] pci 0001:00:13.0: reg 0x20: [io 0x0420-0x042f]
[ 0.289211] pci 0001:00:13.0: reg 0x24: [mem 0x80082000-0x800821ff]
[ 0.289270] pci 0001:00:13.0: reg 0x30: [mem 0x80100000-0x8017ffff pref]
[ 0.289390] pci 0001:00:13.0: supports D1 D2
[ 0.291705] pci 0001:00:15.0: [9710:9865] type 00 class 0x070002
[ 0.291792] pci 0001:00:15.0: reg 0x10: [io 0x0410-0x0417]
[ 0.291851] pci 0001:00:15.0: reg 0x14: [mem 0x8008a000-0x8008afff]
[ 0.291924] pci 0001:00:15.0: reg 0x20: [mem 0x80089000-0x80089fff]
[ 0.292061] pci 0001:00:15.0: supports D1 D2
[ 0.292103] pci 0001:00:15.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.293729] pci 0001:00:15.1: [9710:9865] type 00 class 0x070002
[ 0.293812] pci 0001:00:15.1: reg 0x10: [io 0x0400-0x0407]
[ 0.293871] pci 0001:00:15.1: reg 0x14: [mem 0x80088000-0x80088fff]
[ 0.293944] pci 0001:00:15.1: reg 0x20: [mem 0x80087000-0x80087fff]
[ 0.294078] pci 0001:00:15.1: supports D1 D2
[ 0.294121] pci 0001:00:15.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.297000] pci 0001:00:15.2: [ffff:9865] type 00 class 0x070103
[ 0.297087] pci 0001:00:15.2: reg 0x10: [io 0x0000-0x0007]
[ 0.297145] pci 0001:00:15.2: reg 0x14: [io 0x0000-0x0007]
[ 0.297201] pci 0001:00:15.2: reg 0x18: [mem 0x00000000-0x00000fff]
[ 0.297266] pci 0001:00:15.2: reg 0x20: [mem 0x00000000-0x00000fff]
[ 0.297402] pci 0001:00:15.2: supports D1 D2
[ 0.297445] pci 0001:00:15.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.298994] pci 0001:00:16.0: [14e4:4320] type 00 class 0x028000
[ 0.299075] pci 0001:00:16.0: reg 0x10: [mem 0x8008e000-0x8008ffff]
[ 0.299235] pci 0001:00:16.0: supports D1 D2
[ 0.299277] pci 0001:00:16.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.301407] pci 0001:00:17.0: [106b:0022] type 00 class 0xff0000
[ 0.301491] pci 0001:00:17.0: reg 0x10: [mem 0x80000000-0x8007ffff]
[ 0.303389] pci 0001:00:18.0: [106b:0019] type 00 class 0x0c0310
[ 0.303473] pci 0001:00:18.0: reg 0x10: [mem 0x80086000-0x80086fff]
[ 0.305605] pci 0001:00:19.0: [106b:0019] type 00 class 0x0c0310
[ 0.305718] pci 0001:00:19.0: reg 0x10: [mem 0x80085000-0x80085fff]
[ 0.308114] pci 0001:00:1b.0: [1033:0035] type 00 class 0x0c0310
[ 0.308201] pci 0001:00:1b.0: reg 0x10: [mem 0x80084000-0x80084fff]
[ 0.308365] pci 0001:00:1b.0: supports D1 D2
[ 0.308409] pci 0001:00:1b.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.310734] pci 0001:00:1b.1: [1033:0035] type 00 class 0x0c0310
[ 0.310820] pci 0001:00:1b.1: reg 0x10: [mem 0x80083000-0x80083fff]
[ 0.310983] pci 0001:00:1b.1: supports D1 D2
[ 0.311026] pci 0001:00:1b.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.312725] pci 0001:00:1b.2: [1033:00e0] type 00 class 0x0c0320
[ 0.312807] pci 0001:00:1b.2: reg 0x10: [mem 0x80080000-0x800800ff]
[ 0.312967] pci 0001:00:1b.2: supports D1 D2
[ 0.313009] pci 0001:00:1b.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.315439] pci_bus 0001:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.321091] PCI host bridge to bus 0002:00
[ 0.321171] pci_bus 0002:00: root bus resource [io 0x880000-0x107ffff] (bus address [0x0000-0x7fffff])
[ 0.321249] pci_bus 0002:00: root bus resource [mem 0xf5000000-0xf5ffffff]
[ 0.321317] pci_bus 0002:00: root bus resource [bus 00-ff]
[ 0.321368] pci_bus 0002:00: busn_res: [bus 00-ff] end is updated to ff
[ 0.323054] pci 0002:00:0b.0: [106b:0036] type 00 class 0x060000
[ 0.325345] pci 0002:00:0d.0: [106b:0033] type 00 class 0xff0000
[ 0.325429] pci 0002:00:0d.0: reg 0x10: [mem 0xf5004000-0xf5007fff]
[ 0.327656] pci 0002:00:0e.0: [106b:0031] type 00 class 0x0c0010
[ 0.327739] pci 0002:00:0e.0: reg 0x10: [mem 0xf5000000-0xf5000fff]
[ 0.327896] pci 0002:00:0e.0: supports D1 D2
[ 0.327939] pci 0002:00:0e.0: PME# supported from D0 D1 D2 D3hot
[ 0.330121] pci 0002:00:0f.0: [106b:0032] type 00 class 0x020000
[ 0.330205] pci 0002:00:0f.0: reg 0x10: [mem 0xf5200000-0xf53fffff]
[ 0.330310] pci 0002:00:0f.0: reg 0x30: [mem 0xf5100000-0xf51fffff pref]
[ 0.333709] pci_bus 0002:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.335261] PCI 0000:00 Cannot reserve Legacy IO [io 0xff780000-0xff780fff]
[ 0.335345] PCI 0001:00 Cannot reserve Legacy IO [io 0x0000-0x0fff]
[ 0.335424] pci_bus 0000:00: resource 4 [io 0xff780000-0xfff7ffff]
[ 0.335478] pci_bus 0000:00: resource 5 [mem 0xf1000000-0xf1ffffff]
[ 0.335529] pci_bus 0000:00: resource 6 [mem 0x90000000-0xafffffff]
[ 0.335648] pci 0001:00:15.2: BAR 2: assigned [mem 0xf3000000-0xf3000fff]
[ 0.335714] pci 0001:00:15.2: BAR 4: assigned [mem 0xf3001000-0xf3001fff]
[ 0.335775] pci 0001:00:15.2: BAR 0: assigned [io 0x1000-0x1007]
[ 0.335834] pci 0001:00:15.2: BAR 1: assigned [io 0x1008-0x100f]
[ 0.335913] pci_bus 0001:00: resource 4 [io 0x0000-0x7fffff]
[ 0.335962] pci_bus 0001:00: resource 5 [mem 0xf3000000-0xf3ffffff]
[ 0.336012] pci_bus 0001:00: resource 6 [mem 0x80000000-0x8fffffff]
[ 0.336068] pci_bus 0002:00: resource 4 [io 0x880000-0x107ffff]
[ 0.336117] pci_bus 0002:00: resource 5 [mem 0xf5000000-0xf5ffffff]
[ 0.414065] raid6: altivecx8 gen() 554 MB/s
[ 0.470929] raid6: altivecx4 gen() 533 MB/s
[ 0.527770] raid6: altivecx2 gen() 474 MB/s
[ 0.584620] raid6: altivecx1 gen() 376 MB/s
[ 0.641552] raid6: int32x8 gen() 136 MB/s
[ 0.698281] raid6: int32x4 gen() 130 MB/s
[ 0.755234] raid6: int32x2 gen() 113 MB/s
[ 0.811970] raid6: int32x1 gen() 89 MB/s
[ 0.812008] raid6: using algorithm altivecx8 gen() 554 MB/s
[ 0.812047] raid6: using intx1 recovery algorithm
[ 0.825596] SCSI subsystem initialized
[ 0.828967] libata version 3.00 loaded.
[ 0.831100] usbcore: registered new interface driver usbfs
[ 0.831705] usbcore: registered new interface driver hub
[ 0.833036] usbcore: registered new device driver usb
[ 0.850708] pci 0000:00:10.0: vgaarb: setting as boot VGA device
[ 0.850791] pci 0000:00:10.0: vgaarb: bridge control possible
[ 0.850834] pci 0000:00:10.0: vgaarb: VGA device added: decodes=io+mem,owns=mem,locks=none
[ 0.850951] vgaarb: loaded
[ 0.852521] clocksource: Switched to clocksource timebase
[ 0.987824] NET: Registered PF_INET protocol family
[ 0.990977] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.999756] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 10240 bytes, linear)
[ 1.004428] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.006717] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 1.016369] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear)
[ 1.018699] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.022106] UDP hash table entries: 512 (order: 2, 24576 bytes, linear)
[ 1.022985] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes, linear)
[ 1.025172] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.026806] pci 0001:00:12.0: enabling device (0000 -> 0002)
[ 1.027079] pci 0001:00:12.1: enabling device (0000 -> 0002)
[ 1.027220] pci 0001:00:12.2: enabling device (0004 -> 0006)
[ 1.027499] Apple USB OHCI 0001:00:18.0 disabled by firmware
[ 1.027545] pci 0001:00:18.0: Can't enable PCI device, BIOS handoff failed.
[ 1.027617] Apple USB OHCI 0001:00:19.0 disabled by firmware
[ 1.027657] pci 0001:00:19.0: Can't enable PCI device, BIOS handoff failed.
[ 1.027738] pci 0001:00:1b.0: enabling device (0000 -> 0002)
[ 1.027868] pci 0001:00:1b.1: enabling device (0000 -> 0002)
[ 1.028066] pci 0001:00:1b.2: enabling device (0004 -> 0006)
[ 1.028267] pci 0002:00:0f.0: CLS mismatch (32 != 1020), using 32 bytes
[ 1.029626] Thermal assist unit not available
[ 1.044490] Initialise system trusted keyrings
[ 1.046212] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[ 1.074671] fuse: init (API version 7.38)
[ 1.077669] 9p: Installing v9fs 9p2000 file system support
[ 1.079960] NET: Registered PF_ALG protocol family
[ 1.080318] xor: measuring software checksum speed
[ 1.162937] 8regs : 119 MB/sec
[ 1.244849] 8regs_prefetch : 120 MB/sec
[ 1.326136] 32regs : 121 MB/sec
[ 1.408590] 32regs_prefetch : 119 MB/sec
[ 1.427805] altivec : 513 MB/sec
[ 1.427845] xor: using function: altivec (513 MB/sec)
[ 1.427961] Key type asymmetric registered
[ 1.428004] Asymmetric key parser 'x509' registered
[ 1.456947] bounce: pool size: 64 pages
[ 1.458884] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.458955] io scheduler kyber registered
[ 1.459627] io scheduler bfq registered
[ 1.491400] MacIO PCI driver attached to Keylargo chipset
[ 1.515720] 0.00013020:ch-a: ttyS0 at MMIO 0x80013020 (irq = 22, base_baud = 230400) is a Z85c30 ESCC - Serial port
[ 1.525568] 0.00013000:ch-b: ttyS1 at MMIO 0x80013000 (irq = 23, base_baud = 230400) is a Z85c30 ESCC - Serial port
[ 1.547235] sata_sil 0001:00:13.0: version 2.4
[ 1.548198] sata_sil 0001:00:13.0: enabling device (0004 -> 0007)
[ 1.560829] scsi host0: sata_sil
[ 1.568835] scsi host1: sata_sil
[ 1.571813] ata1: SATA max UDMA/100 mmio m512@0x80082000 tf 0x80082080 irq 53
[ 1.571881] ata2: SATA max UDMA/100 mmio m512@0x80082000 tf 0x800820c0 irq 53
[ 1.574656] pata-pci-macio 0002:00:0d.0: enabling device (0004 -> 0006)
[ 1.589230] pata-pci-macio 0002:00:0d.0: Activating pata-macio chipset UniNorth ATA-6, Apple bus ID 3
[ 1.599220] scsi host2: pata_macio
[ 1.602337] ata3: PATA max UDMA/100 irq 39
[ 1.885950] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1.888934] ata1.00: ATA-9: SanDisk SSD PLUS 240GB, UF4500RL, max UDMA/133
[ 1.888999] ata1.00: 468877312 sectors, multi 1: LBA48 NCQ (depth 0/32)
[ 1.890446] ata1.00: Features: Dev-Sleep
[ 1.914162] ata1.00: configured for UDMA/100
[ 1.915740] scsi 0:0:0:0: Direct-Access ATA SanDisk SSD PLUS 00RL PQ: 0 ANSI: 5
[ 1.926890] sd 0:0:0:0: [sda] 468877312 512-byte logical blocks: (240 GB/224 GiB)
[ 1.927180] sd 0:0:0:0: [sda] Write Protect is off
[ 1.927255] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.927775] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.928484] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[ 1.939700] sda: [mac] sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8
[ 1.955139] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.352605] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2.355136] ata2.00: ATA-9: WDC WD5000LPLX-60ZNTT1, 02.01A02, max UDMA/133
[ 2.355195] ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 2.357867] ata2.00: configured for UDMA/100
[ 2.359013] scsi 1:0:0:0: Direct-Access ATA WDC WD5000LPLX-6 1A02 PQ: 0 ANSI: 5
[ 2.367637] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[ 2.367747] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 2.368000] sd 1:0:0:0: [sdb] Write Protect is off
[ 2.368075] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2.368631] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.369183] sd 1:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes
[ 2.642556] pata-macio 0.0001f000:ata-4: Activating pata-macio chipset KeyLargo ATA-4, Apple bus ID 2
[ 2.653583] scsi host3: pata_macio
[ 2.656504] ata4: PATA max UDMA/66 irq 19
[ 2.815276] ata4.00: CFA: DeLOCK 54143 512MB, 100511E, max UDMA/66
[ 2.815364] ata4.00: 1009008 sectors, multi 1: LBA
[ 3.117614] sdb: [mac] sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8
[ 3.132957] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 3.135142] scsi 3:0:0:0: Direct-Access ATA DeLOCK 54143 512 11E PQ: 0 ANSI: 5
[ 3.144089] sd 3:0:0:0: [sdc] 1009008 512-byte logical blocks: (517 MB/493 MiB)
[ 3.144565] sd 3:0:0:0: [sdc] Write Protect is off
[ 3.144640] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 3.145026] sd 3:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 3.145540] sd 3:0:0:0: [sdc] Preferred minimum I/O size 512 bytes
[ 3.156345] sdc: [mac] sdc1 sdc2 sdc3 sdc4 sdc5 sdc6
[ 3.169932] sd 3:0:0:0: [sdc] Attached SCSI disk
[ 3.682552] pata-macio 0.00020000:ata-3: Activating pata-macio chipset KeyLargo ATA-3, Apple bus ID 0
[ 3.692783] scsi host4: pata_macio
[ 3.695543] ata5: PATA max MWDMA2 irq 20
[ 3.697420] tun: Universal TUN/TAP device driver, 1.6
[ 3.700775] sungem.c:v1.0 David S. Miller <davem@redhat.com>
[ 3.714005] gem 0002:00:0f.0 eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0a:95:9c:76:3a
[ 3.718696] ehci-pci 0001:00:12.2: EHCI Host Controller
[ 3.718893] ehci-pci 0001:00:12.2: new USB bus registered, assigned bus number 1
[ 3.720942] ehci-pci 0001:00:12.2: irq 52, io mem 0x80081000
[ 3.726334] rtc-generic rtc-generic: registered as rtc0
[ 3.728949] PowerMac i2c bus pmu 2 registered
[ 3.731063] PowerMac i2c bus pmu 1 registered
[ 3.732916] ehci-pci 0001:00:12.2: USB 2.0 started, EHCI 1.00
[ 3.734866] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[ 3.734942] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.734996] usb usb1: Product: EHCI Host Controller
[ 3.735037] usb usb1: Manufacturer: Linux 6.5.0-rc6-PMacG4-dirty ehci_hcd
[ 3.735083] usb usb1: SerialNumber: 0001:00:12.2
[ 3.739388] PowerMac i2c bus mac-io 0 registered
[ 3.740202] hub 1-0:1.0: USB hub found
[ 3.740505] hub 1-0:1.0: 5 ports detected
[ 3.741013] i2c i2c-2: No i2c address for /pci@f2000000/mac-io@17/i2c@18000/i2c-modem
[ 3.743193] PowerMac i2c bus uni-n 1 registered
[ 3.743269] i2c i2c-3: i2c-powermac: modalias failure on /uni-n@f8000000/i2c@f8001000/cereal@1c0
[ 3.745210] PowerMac i2c bus uni-n 0 registered
[ 3.749993] ehci-pci 0001:00:1b.2: EHCI Host Controller
[ 3.750167] ehci-pci 0001:00:1b.2: new USB bus registered, assigned bus number 2
[ 3.751074] ehci-pci 0001:00:1b.2: irq 63, io mem 0x80080000
[ 3.754287] hid: raw HID events driver (C) Jiri Kosina
[ 3.757688] usbcore: registered new interface driver usbhid
[ 3.757748] usbhid: USB HID core driver
[ 3.762692] ehci-pci 0001:00:1b.2: USB 2.0 started, EHCI 1.00
[ 3.765134] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[ 3.765212] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.765266] usb usb2: Product: EHCI Host Controller
[ 3.765308] usb usb2: Manufacturer: Linux 6.5.0-rc6-PMacG4-dirty ehci_hcd
[ 3.765354] usb usb2: SerialNumber: 0001:00:1b.2
[ 3.770858] hub 2-0:1.0: USB hub found
[ 3.771144] hub 2-0:1.0: 5 ports detected
[ 3.775606] NET: Registered PF_INET6 protocol family
[ 3.788894] Segment Routing with IPv6
[ 3.789603] In-situ OAM (IOAM) with IPv6
[ 3.790140] NET: Registered PF_PACKET protocol family
[ 3.790228] NET: Registered PF_KEY protocol family
[ 3.792178] 9pnet: Installing 9P2000 support
[ 3.795687] drmem: No dynamic reconfiguration memory found
[ 3.855138] ata5.00: ATAPI: _NEC DVD_RW ND-3520A, 1.04, max UDMA/33
[ 3.863213] scsi 4:0:0:0: CD-ROM _NEC DVD_RW ND-3520A 1.04 PQ: 0 ANSI: 5
[ 3.964853] Loading compiled-in X.509 certificates
[ 3.998229] sr 4:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 3.998364] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 3.999290] usb 1-5: new high-speed USB device number 2 using ehci-pci
[ 4.067710] sr 4:0:0:0: Attached scsi CD-ROM sr0
[ 4.088580] zswap: loaded using pool zstd/z3fold
[ 4.149495] usb 1-5: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=32.98
[ 4.149601] usb 1-5: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 4.149651] usb 1-5: Product: USB2.0 Hub
[ 4.154577] hub 1-5:1.0: USB hub found
[ 4.155240] hub 1-5:1.0: 4 ports detected
[ 4.223260] debug_vm_pgtable: [debug_vm_pgtable ]: Validating architecture page table helpers
[ 4.338577] Btrfs loaded, zoned=no, fsverity=no
[ 4.502555] usb 1-5.1: new low-speed USB device number 3 using ehci-pci
[ 4.635910] usb 1-5.1: New USB device found, idVendor=04d9, idProduct=0006, bcdDevice= 1.40
[ 4.635994] usb 1-5.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.636049] usb 1-5.1: Product: RPI Wired Keyboard 5
[ 4.636090] usb 1-5.1: Manufacturer:
[ 4.673879] input: RPI Wired Keyboard 5 as /devices/pci0001:00/0001:00:12.2/usb1/1-5/1-5.1/1-5.1:1.0/0003:04D9:0006.0001/input/input0
[ 4.752958] hid-generic 0003:04D9:0006.0001: input,hidraw0: USB HID v1.11 Keyboard [ RPI Wired Keyboard 5] on usb-0001:00:12.2-5.1/input0
[ 4.782410] input: RPI Wired Keyboard 5 as /devices/pci0001:00/0001:00:12.2/usb1/1-5/1-5.1/1-5.1:1.1/0003:04D9:0006.0002/input/input1
[ 4.853391] hid-generic 0003:04D9:0006.0002: input,hidraw1: USB HID v1.11 Device [ RPI Wired Keyboard 5] on usb-0001:00:12.2-5.1/input1
[ 4.939377] usb 1-5.4: new low-speed USB device number 4 using ehci-pci
[ 5.049116] usb 1-5.4: New USB device found, idVendor=275d, idProduct=0ba6, bcdDevice= 1.00
[ 5.049215] usb 1-5.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 5.049270] usb 1-5.4: Product: USB OPTICAL MOUSE
[ 5.072278] input: USB OPTICAL MOUSE as /devices/pci0001:00/0001:00:12.2/usb1/1-5/1-5.4/1-5.4:1.0/0003:275D:0BA6.0003/input/input2
[ 5.083036] hid-generic 0003:275D:0BA6.0003: input,hidraw2: USB HID v1.11 Mouse [USB OPTICAL MOUSE ] on usb-0001:00:12.2-5.4/input0
[ 10.320546] input: PMU as /devices/virtual/input/input3
[ 10.322814] netpoll: netconsole: local port 6666
[ 10.322870] netpoll: netconsole: local IPv4 address 192.168.178.8
[ 10.322919] netpoll: netconsole: interface 'eth0'
[ 10.322954] netpoll: netconsole: remote port 6666
[ 10.322988] netpoll: netconsole: remote IPv4 address 192.168.178.3
[ 10.323029] netpoll: netconsole: remote ethernet address 70:85:c2:30:ec:01
[ 10.323082] netpoll: netconsole: device eth0 not up yet, forcing it
[ 10.429594] sungem_phy: PHY ID: 2060e1, addr: 0
[ 10.429903] gem 0002:00:0f.0 eth0: Found BCM5421 PHY
[ 14.109537] gem 0002:00:0f.0 eth0: Link is up at 1000 Mbps, full-duplex
[ 14.109740] gem 0002:00:0f.0 eth0: Pause is enabled (rxfifo: 10240 off: 7168 on: 5632)
[ 14.121017] printk: console [netcon0] enabled
[ 14.165250] netconsole: network logging started
[ 14.371907] EXT4-fs (sda5): mounted filesystem 28419c7c-4bc4-4922-bdc8-6d8515c62385 ro with ordered data mode. Quota mode: disabled.
[ 14.372468] VFS: Mounted root (ext4 filesystem) readonly on device 8:5.
[ 14.377462] devtmpfs: mounted
[ 14.382323] Freeing unused kernel image (initmem) memory: 1344K
[ 14.416600] Checked W+X mappings: passed, no W+X pages found
[ 14.416805] rodata_test: all tests were successful
[ 14.416924] kallsyms_selftest: start
[ 14.416974] Run /usr/lib/systemd/systemd as init process
[ 14.417374] with arguments:
[ 14.417581] /usr/lib/systemd/systemd
[ 14.417685] with environment:
[ 14.417784] HOME=/
[ 14.417858] TERM=linux
[ 15.259948] systemd[1]: systemd 253 running in system mode (+PAM -AUDIT -SELINUX -APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID -CURL +ELFUTILS -FIDO2 +IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 +LZ4 -XZ -ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP -SYSVINIT default-hierarchy=unified)
[ 15.260335] systemd[1]: Detected architecture ppc.
[ 15.288120] systemd[1]: Hostname set to <T600>.
[ 15.466171] memfd_create() without MFD_EXEC nor MFD_NOEXEC_SEAL, pid=1 'systemd'
[ 18.124529] systemd[1]: Queued start job for default target graphical.target.
[ 18.348712] systemd[1]: Created slice system-getty.slice.
[ 18.365557] systemd[1]: Created slice system-modprobe.slice.
[ 18.380022] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 18.393768] systemd[1]: Created slice system-vncserver.slice.
[ 18.407854] systemd[1]: Created slice user.slice.
[ 18.413289] systemd[1]: Started systemd-ask-password-console.path.
[ 18.419364] systemd[1]: Started systemd-ask-password-wall.path.
[ 18.430895] systemd[1]: Set up automount proc-sys-fs-binfmt_misc.automount.
[ 18.433512] systemd[1]: Reached target paths.target.
[ 18.434692] systemd[1]: Reached target remote-fs.target.
[ 18.435975] systemd[1]: Reached target slices.target.
[ 18.461635] systemd[1]: Listening on systemd-coredump.socket.
[ 18.470841] systemd[1]: Listening on systemd-journald-dev-log.socket.
[ 18.479088] systemd[1]: Listening on systemd-journald.socket.
[ 18.489973] systemd[1]: Listening on systemd-udevd-control.socket.
[ 18.498405] systemd[1]: Listening on systemd-udevd-kernel.socket.
[ 18.506471] systemd[1]: dev-hugepages.mount was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/mm/hugepages).
[ 18.542192] systemd[1]: Mounting dev-mqueue.mount...
[ 18.615631] systemd[1]: Mounting sys-kernel-debug.mount...
[ 18.625908] systemd[1]: sys-kernel-tracing.mount was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/tracing).
[ 18.699088] systemd[1]: Starting kmod-static-nodes.service...
[ 18.972103] systemd[1]: Starting modprobe@configfs.service...
[ 19.045405] systemd[1]: Starting modprobe@dm_mod.service...
[ 19.141739] systemd[1]: Starting modprobe@drm.service...
[ 19.224442] device-mapper: uevent: version 1.0.3
[ 19.239789] systemd[1]: Starting modprobe@fuse.service...
[ 19.243195] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[ 19.318842] systemd[1]: Starting modprobe@loop.service...
[ 19.480979] loop: module loaded
[ 19.485689] systemd[1]: Starting systemd-fsck-root.service...
[ 19.608030] systemd[1]: Starting systemd-journald.service...
[ 19.711895] systemd[1]: Starting systemd-modules-load.service...
[ 19.921134] systemd[1]: Starting systemd-udev-trigger.service...
[ 20.215096] systemd-journald[107]: Collecting audit messages is disabled.
[ 20.298025] systemd[1]: Mounted dev-mqueue.mount.
[ 20.318721] systemd[1]: Mounted sys-kernel-debug.mount.
[ 20.355383] systemd[1]: Finished kmod-static-nodes.service.
[ 20.395787] systemd[1]: modprobe@configfs.service: Deactivated successfully.
[ 20.407734] systemd[1]: Finished modprobe@configfs.service.
[ 20.465648] systemd[1]: modprobe@dm_mod.service: Deactivated successfully.
[ 20.486306] systemd[1]: Finished modprobe@dm_mod.service.
[ 20.574492] systemd[1]: modprobe@drm.service: Deactivated successfully.
[ 20.589669] systemd[1]: Finished modprobe@drm.service.
[ 20.621201] systemd[1]: modprobe@fuse.service: Deactivated successfully.
[ 20.639477] systemd[1]: Finished modprobe@fuse.service.
[ 20.689494] systemd[1]: modprobe@loop.service: Deactivated successfully.
[ 20.701508] systemd[1]: Finished modprobe@loop.service.
[ 20.728000] systemd[1]: Finished systemd-modules-load.service.
[ 20.943570] systemd[1]: Mounting sys-fs-fuse-connections.mount...
[ 21.226765] systemd[1]: Mounting sys-kernel-config.mount...
[ 21.243527] systemd[1]: systemd-repart.service was skipped because no trigger condition checks were met.
[ 21.443122] systemd[1]: Starting systemd-sysctl.service...
[ 21.728019] systemd[1]: Finished systemd-fsck-root.service.
[ 21.757858] systemd[1]: Mounted sys-fs-fuse-connections.mount.
[ 21.775866] systemd[1]: Mounted sys-kernel-config.mount.
[ 21.904317] systemd[1]: Starting systemd-remount-fs.service...
[ 22.144178] systemd[1]: Finished systemd-sysctl.service.
[ 26.286066] EXT4-fs (sda5): re-mounted 28419c7c-4bc4-4922-bdc8-6d8515c62385 r/w. Quota mode: disabled.
[ 26.373113] systemd[1]: Finished systemd-remount-fs.service.
[ 26.375775] systemd[1]: systemd-firstboot.service was skipped because of an unmet condition check (ConditionFirstBoot=yes).
[ 26.403818] systemd[1]: systemd-hwdb-update.service was skipped because of an unmet condition check (ConditionNeedsUpdate=/etc).
[ 26.635624] systemd[1]: Starting systemd-random-seed.service...
[ 26.646292] systemd[1]: systemd-sysusers.service was skipped because no trigger condition checks were met.
[ 26.789498] systemd[1]: Starting systemd-tmpfiles-setup-dev.service...
[ 27.257751] systemd[1]: Started systemd-journald.service.
[ 27.852570] random: crng init done
[ 28.045017] systemd-journald[107]: Received client request to flush runtime journal.
[ 28.299842] systemd-journald[107]: /var/log/journal/71303955349d475c9d69360df5e2c5b5/system.journal: Monotonic clock jumped backwards relative to last journal entry, rotating.
[ 28.300160] systemd-journald[107]: Rotating system journal.
[ 43.363371] BTRFS: device label g4_musl devid 1 transid 64495 /dev/sda4 scanned by (udev-worker) (146)
[ 43.368622] BTRFS: device label tmp devid 1 transid 50 /dev/sda6 scanned by (udev-worker) (138)
[ 45.256268] gem 0002:00:0f.0 enP2p0s15: renamed from eth0 (while UP)
[ 48.481136] kallsyms_selftest: ---------------------------------------------------------
[ 48.481337] kallsyms_selftest: | nr_symbols | compressed size | original size | ratio(%) |
[ 48.481442] kallsyms_selftest: |---------------------------------------------------------|
[ 48.481539] kallsyms_selftest: | 33861 | 364315 | 629849 | 57.84 |
[ 48.481644] kallsyms_selftest: ---------------------------------------------------------
[ 49.804677] Adding 8388604k swap on /dev/sdb6. Priority:-2 extents:1 across:8388604k FS
[ 51.978496] EXT4-fs (sdc5): mounting ext2 file system using the ext4 subsystem
[ 52.007048] EXT4-fs (sdc5): mounted filesystem e4e8af9e-0f0d-44f9-b983-71bf61d782de r/w without journal. Quota mode: disabled.
[ 52.007473] ext2 filesystem being mounted at /boot supports timestamps until 2038-01-19 (0x7fffffff)
[ 52.955624] ohci-pci 0001:00:12.0: OHCI PCI host controller
[ 53.016581] ohci-pci 0001:00:12.0: new USB bus registered, assigned bus number 3
[ 53.017865] ohci-pci 0001:00:12.0: irq 52, io mem 0x8008c000
[ 53.289723] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.05
[ 53.289993] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 53.290111] usb usb3: Product: OHCI PCI host controller
[ 53.290244] usb usb3: Manufacturer: Linux 6.5.0-rc6-PMacG4-dirty ohci_hcd
[ 53.290379] usb usb3: SerialNumber: 0001:00:12.0
[ 53.379364] hub 3-0:1.0: USB hub found
[ 53.396053] hub 3-0:1.0: 3 ports detected
[ 53.434213] ohci-pci 0001:00:12.1: OHCI PCI host controller
[ 53.434546] ohci-pci 0001:00:12.1: new USB bus registered, assigned bus number 4
[ 53.435250] ohci-pci 0001:00:12.1: irq 52, io mem 0x8008b000
[ 53.511553] kallsyms_selftest: kallsyms_lookup_name() looked up 33861 symbols
[ 53.511807] kallsyms_selftest: The time spent on each symbol is (ns): min=6745, max=1261467, avg=98935
[ 53.555928] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.05
[ 53.556204] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 53.556350] usb usb4: Product: OHCI PCI host controller
[ 53.556478] usb usb4: Manufacturer: Linux 6.5.0-rc6-PMacG4-dirty ohci_hcd
[ 53.556608] usb usb4: SerialNumber: 0001:00:12.1
[ 53.591692] kallsyms_selftest: kallsyms_on_each_symbol() traverse all: 79609211 ns
[ 53.591968] kallsyms_selftest: kallsyms_on_each_match_symbol() traverse all: 81183 ns
[ 53.592077] kallsyms_selftest: finish
[ 53.594364] hub 4-0:1.0: USB hub found
[ 53.610472] hub 4-0:1.0: 2 ports detected
[ 53.684691] Apple USB OHCI 0001:00:18.0 disabled by firmware
[ 53.684998] Apple USB OHCI 0001:00:19.0 disabled by firmware
[ 53.685526] ohci-pci 0001:00:1b.0: OHCI PCI host controller
[ 53.685888] ohci-pci 0001:00:1b.0: new USB bus registered, assigned bus number 5
[ 53.723044] ohci-pci 0001:00:1b.0: irq 63, io mem 0x80084000
[ 53.821459] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.05
[ 53.821669] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 53.821784] usb usb5: Product: OHCI PCI host controller
[ 53.821941] usb usb5: Manufacturer: Linux 6.5.0-rc6-PMacG4-dirty ohci_hcd
[ 53.822078] usb usb5: SerialNumber: 0001:00:1b.0
[ 53.851856] hub 5-0:1.0: USB hub found
[ 53.862880] hub 5-0:1.0: 3 ports detected
[ 53.889638] ohci-pci 0001:00:1b.1: OHCI PCI host controller
[ 53.889973] ohci-pci 0001:00:1b.1: new USB bus registered, assigned bus number 6
[ 53.890918] ohci-pci 0001:00:1b.1: irq 63, io mem 0x80083000
[ 54.012374] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.05
[ 54.012748] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 54.012866] usb usb6: Product: OHCI PCI host controller
[ 54.012965] usb usb6: Manufacturer: Linux 6.5.0-rc6-PMacG4-dirty ohci_hcd
[ 54.013134] usb usb6: SerialNumber: 0001:00:1b.1
[ 54.032859] hub 6-0:1.0: USB hub found
[ 54.062739] hub 6-0:1.0: 2 ports detected
[ 54.545097] BTRFS info (device sda6): using xxhash64 (xxhash64-generic) checksum algorithm
[ 54.545361] BTRFS info (device sda6): use lzo compression, level 0
[ 54.545521] BTRFS info (device sda6): using free space tree
[ 54.626386] BTRFS info (device sda6): enabling ssd optimizations
[ 55.370236] b43-pci-bridge 0001:00:16.0: enabling device (0004 -> 0006)
[ 55.370588] ssb: Found chip with id 0x4306, rev 0x02 and package 0x00
[ 55.411720] b43-pci-bridge 0001:00:16.0: Sonics Silicon Backplane found on PCI device 0001:00:16.0
[ 56.807103] firewire_ohci 0002:00:0e.0: enabling device (0000 -> 0002)
[ 56.876276] firewire_ohci 0002:00:0e.0: added OHCI v1.10 device as card 0, 8 IR + 8 IT contexts, quirks 0x0
[ 57.394974] firewire_core 0002:00:0e.0: created device fw0: GUID 000a95fffe9c763a, S800
[ 58.456135] ADM1030 fan controller [@2c]
[ 58.471323] DS1775 digital thermometer [@49]
[ 58.471538] Temp: 50.8 C
[ 58.471557] Hyst: 70.0 C
[ 58.471680] OS: 75.0 C
[ 58.472087]
[ 59.322461] [drm] radeon kernel modesetting enabled.
[ 59.370100] radeon 0000:00:10.0: vgaarb: deactivate vga console
[ 59.434319] radeon 0000:00:10.0: enabling device (0006 -> 0007)
[ 59.546842] [drm] initializing kernel modesetting (RV350 0x1002:0x4150 0x1002:0x0002 0x00).
[ 59.547082] [drm] Forcing AGP to PCI mode
[ 59.548708] radeon 0000:00:10.0: Invalid PCI ROM header signature: expecting 0xaa55, got 0x0000
[ 59.919760] [drm] Generation 2 PCI interface, using max accessible memory
[ 59.920023] radeon 0000:00:10.0: VRAM: 256M 0x00000000A0000000 - 0x00000000AFFFFFFF (256M used)
[ 59.920158] radeon 0000:00:10.0: GTT: 512M 0x0000000080000000 - 0x000000009FFFFFFF
[ 59.920471] [drm] Detected VRAM RAM=256M, BAR=256M
[ 59.920606] [drm] RAM width 128bits DDR
[ 59.959678] [drm] radeon: 256M of VRAM memory ready
[ 59.959948] [drm] radeon: 512M of GTT memory ready.
[ 59.960463] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 60.436950] [drm] radeon: 1 quad pipes, 1 Z pipes initialized
[ 60.437151] [drm] PCI GART of 512M enabled (table at 0x0000000009F80000).
[ 60.437517] radeon 0000:00:10.0: WB enabled
[ 60.437640] radeon 0000:00:10.0: fence driver on ring 0 use gpu addr 0x0000000080000000
[ 60.486773] [drm] radeon: irq initialized.
[ 60.487133] [drm] Loading R300 Microcode
[ 61.239969] [drm] radeon: ring at 0x0000000080001000
[ 61.240291] [drm] ring test succeeded in 0 usecs
[ 61.392992] [drm] ib test succeeded in 0 usecs
[ 61.532465] [drm] Radeon Display Connectors
[ 61.532731] [drm] Connector 0:
[ 61.532820] [drm] DVI-I-1
[ 61.532904] [drm] HPD2
[ 61.533040] [drm] DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[ 61.533147] [drm] Encoders:
[ 61.533230] [drm] CRT1: INTERNAL_DAC1
[ 61.533320] [drm] DFP2: INTERNAL_DVO1
[ 61.533409] [drm] Connector 1:
[ 61.533490] [drm] DVI-I-2
[ 61.533570] [drm] HPD1
[ 61.533650] [drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[ 61.533748] [drm] Encoders:
[ 61.533944] [drm] CRT2: INTERNAL_DAC2
[ 61.534035] [drm] DFP1: INTERNAL_TMDS1
[ 61.534324] [drm] Initialized radeon 2.50.0 20080528 for 0000:00:10.0 on minor 0
[ 62.091328] [drm] fb mappable at 0xA0040000
[ 62.091550] [drm] vram apper at 0xA0000000
[ 62.091643] [drm] size 8294400
[ 62.091727] [drm] fb depth is 24
[ 62.091811] [drm] pitch is 7680
[ 63.404226] Console: switching to colour frame buffer device 240x67
[ 63.572055] radeon 0000:00:10.0: [drm] fb0: radeondrmfb frame buffer device
[ 66.622726] CPU-temp: 51.1 C
[ 66.622779] , Case: 31.8 C
[ 66.623346] , Fan: 0 (tuned -11)
[ 75.300412] snd-aoa-fabric-layout: Using direct GPIOs
[ 75.426605] systemd-journald[107]: /var/log/journal/71303955349d475c9d69360df5e2c5b5/user-1000.journal: Monotonic clock jumped backwards relative to last journal entry, rotating.
[ 75.486814] snd-aoa-fabric-layout: can use this codec
[ 75.580248] snd-aoa-codec-tas: tas found, addr 0x35 on /pci@f2000000/mac-io@17/i2c@18000/deq@6a
[ 75.899467] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 76.626204] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 76.653083] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 76.654372] cfg80211: failed to load regulatory.db
[ 77.894542] b43legacy-phy0: Broadcom 4306 WLAN found (core revision 4)
[ 77.932596] b43legacy-phy0 debug: Found PHY: Analog 1, Type 2, Revision 1
[ 77.933689] b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
[ 77.965956] b43legacy-phy0 debug: Radio initialized
[ 77.967813] b43legacy-phy0: Loading firmware b43legacy/ucode4.fw
[ 77.977275] Broadcom 43xx-legacy driver loaded [ Features: PLID ]
[ 77.981667] b43legacy-phy0: Loading firmware b43legacy/pcm4.fw
[ 77.994821] b43legacy-phy0: Loading firmware b43legacy/b0g0initvals2.fw
[ 78.012128] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 113.287868] EXT4-fs (sdc5): unmounting filesystem e4e8af9e-0f0d-44f9-b983-71bf61d782de.
[ 115.227116] systemd-shutdown[1]: Syncing filesystems and block devices.
[ 115.447436] systemd-shutdown[1]: Sending SIGTERM to remaining processes...
[ 115.648554] systemd-journald[107]: Received SIGTERM from PID 1 (systemd-shutdow).
[ 115.802048] systemd-shutdown[1]: Sending SIGKILL to remaining processes...
[ 116.008464] systemd-shutdown[1]: Unmounting file systems.
[ 116.056346] (sd-remount)[437]: Remounting '/' read-only with options ''.
[ 116.119203] EXT4-fs (sda5): re-mounted 28419c7c-4bc4-4922-bdc8-6d8515c62385 ro. Quota mode: disabled.
[ 116.429921] systemd-shutdown[1]: All filesystems unmounted.
[ 116.463790] systemd-shutdown[1]: Deactivating swaps.
[ 116.498214] systemd-shutdown[1]: All swaps deactivated.
[ 116.531576] systemd-shutdown[1]: Detaching loop devices.
[ 116.639432] systemd-shutdown[1]: All loop devices detached.
[ 116.672889] systemd-shutdown[1]: Stopping MD devices.
[ 116.732218] systemd-shutdown[1]: All MD devices stopped.
[ 116.765557] systemd-shutdown[1]: Detaching DM devices.
[ 116.800589] systemd-shutdown[1]: All DM devices detached.
[ 116.834117] systemd-shutdown[1]: All filesystems, swaps, loop devices, MD devices and DM devices detached.
[ 116.901505] systemd-shutdown[1]: Syncing filesystems and block devices.
[ 116.936398] systemd-shutdown[1]: Powering off.
[ 116.971615] sd 3:0:0:0: [sdc] Stopping disk
[ 117.006957] sd 1:0:0:0: [sdb] Synchronizing SCSI cache
[ 117.041914] sd 1:0:0:0: [sdb] Stopping disk
[ 117.388459] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 117.423243] sd 0:0:0:0: [sda] Stopping disk
[ 117.469423] reboot: Power down
next prev parent reply other threads:[~2023-08-15 20:03 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-08-10 23:48 KASAN debug kernel fails to boot at early stage when CONFIG_SMP=y is set (kernel 6.5-rc5, PowerMac G4 3,6) Erhard Furtner
2023-08-11 6:45 ` Christophe Leroy
2023-08-13 19:38 ` Erhard Furtner
2023-08-14 9:40 ` Christophe Leroy
2023-08-14 17:27 ` Erhard Furtner
2023-08-15 17:21 ` [PATCH] Add pr_info() traces for investigation Christophe Leroy
2023-08-15 17:25 ` KASAN debug kernel fails to boot at early stage when CONFIG_SMP=y is set (kernel 6.5-rc5, PowerMac G4 3,6) Christophe Leroy
2023-08-15 20:01 ` Erhard Furtner [this message]
2023-08-16 15:56 ` Christophe Leroy
2023-08-17 18:32 ` Erhard Furtner
2023-08-17 23:13 ` Michael Ellerman
2023-08-18 9:16 ` Erhard Furtner
2023-08-18 15:47 ` Christophe Leroy
2023-08-18 16:23 ` Erhard Furtner
2023-08-22 7:31 ` Christophe Leroy
2023-08-24 0:00 ` Erhard Furtner
2023-08-24 11:36 ` Michael Ellerman
2023-08-27 23:17 ` Erhard Furtner
2023-08-31 5:32 ` Christophe Leroy
2023-08-31 22:44 ` Erhard Furtner
2023-09-01 7:43 ` Christophe Leroy
2023-09-03 21:06 ` Erhard Furtner
2023-09-04 14:48 ` Christophe Leroy
2023-09-04 14:55 ` Christophe Leroy
2023-09-04 21:32 ` Erhard Furtner
2023-09-12 0:11 ` Erhard Furtner
2023-09-12 7:47 ` Christophe Leroy
2023-09-12 15:59 ` Erhard Furtner
2023-09-12 17:39 ` Christophe Leroy
2023-09-12 20:09 ` Erhard Furtner
2023-09-13 5:28 ` Christophe Leroy
2023-09-14 4:54 ` Christophe Leroy
2023-09-14 12:33 ` Erhard Furtner
2024-02-28 23:55 ` Erhard Furtner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230815220156.5c234b52@yea \
--to=erhard_f@mailbox.org \
--cc=christophe.leroy@csgroup.eu \
--cc=linuxppc-dev@lists.ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).