Re: KASAN debug kernel fails to boot at early stage when CONFIG_SMP=y is set (kernel 6.5-rc5, PowerMac G4 3,6)

[Erhard Furtner <erhard_f@mailbox.org>]

[-- Attachment #1: Type: text/plain, Size: 2041 bytes --]

On Fri, 18 Aug 2023 09:13:21 +1000
Michael Ellerman <mpe@ellerman.id.au> wrote:

> Try just removing the call to btext_unmap() entirely and see how far it goes?
> 
> cheers

Ok, I commented out btext_unmap() in MMU_init() and the freeze just happens before the "Linux version 6.5.0-rc6-PMacG4-dirty [...]"-line:

[    0.000000] printk: bootconsole [udbg0] enabled
[    0.000000] Total memory = 2048MB; using 4096kB for hash table
[    0.000000] mapin_ram:125
[    0.000000] mmu_mapin_ram:169 0 30000000 1400000 2000000
[    0.000000] __mmu_mapin_ram:146 0 1400000
[    0.000000] __mmu_mapin_ram:155 1400000
[    0.000000] __mmu_mapin_ram:146 1400000 30000000
[    0.000000] __mmu_mapin_ram:155 20000000
[    0.000000] __mapin_ram_chunk:107 20000000 30000000
[    0.000000] __mapin_ram_chunk:117
[    0.000000] mapin_ram:134
[    0.000000] kasan_mmu_init:129
[    0.000000] kasan_mmu_init:132 0
[    0.000000] kasan_mmu_init:137
[    0.000000] setup_kuap:23
[    0.000000] setup_kuap:25
[    0.000000] setup_kuap:30
[    0.000000] setup_kuap:35
[    0.000000] Activating Kernel Userspace Access Protection
[    0.000000] setup_kuap:40
[    0.000000] Activating Kernel Userspace Execution Prevention

I also tried a kernel without KUAP/KUEP getting this:

[    0.000000] printk: bootconsole [udbg0] enabled
[    0.000000] Total memory = 2048MB; using 4096kB for hash table
[    0.000000] mapin_ram:125
[    0.000000] mmu_mapin_ram:169 0 30000000 1400000 2000000
[    0.000000] __mmu_mapin_ram:146 0 1400000
[    0.000000] __mmu_mapin_ram:155 1400000
[    0.000000] __mmu_mapin_ram:146 1400000 30000000
[    0.000000] __mmu_mapin_ram:155 20000000
[    0.000000] __mapin_ram_chunk:107 20000000 30000000
[    0.000000] __mapin_ram_chunk:117
[    0.000000] mapin_ram:134
[    0.000000] kasan_mmu_init:129
[    0.000000] kasan_mmu_init:132 0
[    0.000000] kasan_mmu_init:137

Here too the freeze just happens before the line "Linux version 6.5.0-rc6-PMacG4-dirty [...]" in dmesg.

Attached is (warm boot) dmesg without KUAP/KUEP.

Regards,
Erhard

[-- Attachment #2: dmesg_65-rc6_g4_04 --]
[-- Type: application/octet-stream, Size: 50751 bytes --]

[    0.000000] printk: bootconsole [udbg0] enabled
[    0.000000] Total memory = 2048MB; using 4096kB for hash table
[    0.000000] mapin_ram:125
[    0.000000] mmu_mapin_ram:169 0 30000000 1400000 2000000
[    0.000000] __mmu_mapin_ram:146 0 1400000
[    0.000000] __mmu_mapin_ram:155 1400000
[    0.000000] __mmu_mapin_ram:146 1400000 30000000
[    0.000000] __mmu_mapin_ram:155 20000000
[    0.000000] __mapin_ram_chunk:107 20000000 30000000
[    0.000000] __mapin_ram_chunk:117
[    0.000000] mapin_ram:134
[    0.000000] kasan_mmu_init:129
[    0.000000] kasan_mmu_init:132 0
[    0.000000] kasan_mmu_init:137
[    0.000000] Linux version 6.5.0-rc6-PMacG4-dirty (root@T1000) (gcc (Gentoo 12.3.1_p20230526 p2) 12.3.1 20230526, GNU ld (Gentoo 2.40 p7) 2.40.0) #7 SMP Fri Aug 18 11:00:54 CEST 2023
[    0.000000] KASAN init done
[    0.000000] ioremap() called early from pmac_feature_init+0x17c/0xe9c. Use early_ioremap() instead
[    0.000000] Found UniNorth memory controller & host bridge @ 0xf8000000 revision: 0x24
[    0.000000] Mapped at 0xf53bf000
[    0.000000] ioremap() called early from probe_one_macio+0x1f8/0x3f8. Use early_ioremap() instead
[    0.000000] Found a Keylargo mac-io controller, rev: 3, mapped at 0x(ptrval)
[    0.000000] PowerMac motherboard: PowerMac G4 Windtunnel
[    0.000000] ioremap() called early from btext_map+0x64/0xdc. Use early_ioremap() instead
[    0.000000] Hardware name: PowerMac3,6 7455 0x80010303 PowerMac
[    0.000000] CPU maps initialized for 1 thread per core
[    0.000000]  (thread shift is 0)
[    0.000000] -----------------------------------------------------
[    0.000000] phys_mem_size     = 0x80000000
[    0.000000] dcache_bsize      = 0x20
[    0.000000] icache_bsize      = 0x20
[    0.000000] cpu_features      = 0x000000002514600a
[    0.000000]   possible        = 0x00000000277de00a
[    0.000000]   always          = 0x0000000001000000
[    0.000000] cpu_user_features = 0x9c000001 0x00000000
[    0.000000] mmu_features      = 0x00010001
[    0.000000] Hash_size         = 0x400000
[    0.000000] Hash_mask         = 0xffff
[    0.000000] -----------------------------------------------------
[    0.000000] ioremap() called early from pmac_setup_arch+0x1ac/0x448. Use early_ioremap() instead
[    0.000000] ioremap() called early from find_via_pmu+0x2a8/0x430. Use early_ioremap() instead
[    0.000000] ioremap() called early from find_via_pmu+0x2e4/0x430. Use early_ioremap() instead
[    0.000000] via-pmu: Server Mode is disabled
[    0.000000] PMU driver v2 initialized for Core99, firmware: 0c
[    0.000000] ioremap() called early from pmac_nvram_init+0x208/0x7c4. Use early_ioremap() instead
[    0.000000] nvram: Checking bank 0...
[    0.000000] nvram: gen0=3200, gen1=3201
[    0.000000] nvram: Active bank is: 1
[    0.000000] nvram: OF partition at 0x410
[    0.000000] nvram: XP partition at 0x1020
[    0.000000] nvram: NR partition at 0x1120
[    0.000000] Top of RAM: 0x80000000, Total RAM: 0x80000000
[    0.000000] Memory hole size: 0MB
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x000000002fffffff]
[    0.000000]   Normal   empty
[    0.000000]   HighMem  [mem 0x0000000030000000-0x000000007fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000007fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[    0.000000] percpu: Embedded 14 pages/cpu s24608 r8192 d24544 u57344
[    0.000000] pcpu-alloc: s24608 r8192 d24544 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Kernel command line: ro root=/dev/sda5 zswap.max_pool_percent=16 slub_debug=FZP page_poison=1 netconsole=6666@192.168.178.8/eth0,6666@192.168.178.3/70:85:C2:30:EC:01 init=/usr/lib/systemd/systemd 
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 522560
[    0.000000] mem auto-init: stack:all(pattern), heap alloc:off, heap free:off
[    0.000000] stackdepot: allocating hash table via alloc_large_system_hash
[    0.000000] stackdepot hash table entries: 1048576 (order: 10, 4194304 bytes, linear)
[    0.000000] Kernel virtual memory layout:
[    0.000000]   * 0xf6000000..0xfec00000  : kasan shadow mem
[    0.000000]   * 0xf5bbf000..0xf5fff000  : fixmap
[    0.000000]   * 0xf5400000..0xf5800000  : highmem PTEs
[    0.000000]   * 0xf5115000..0xf5400000  : early ioremap
[    0.000000]   * 0xf1000000..0xf5110000  : vmalloc & ioremap
[    0.000000]   * 0xb0000000..0xc0000000  : modules
[    0.000000] Memory: 1946552K/2097152K available (16020K kernel code, 1964K rwdata, 4460K rodata, 1344K init, 402K bss, 150600K reserved, 0K cma-reserved, 1212416K highmem)
[    0.000000] **********************************************************
[    0.000000] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
[    0.000000] **                                                      **
[    0.000000] ** This system shows unhashed kernel memory addresses   **
[    0.000000] ** via the console, logs, and other interfaces. This    **
[    0.000000] ** might reduce the security of your system.            **
[    0.000000] **                                                      **
[    0.000000] ** If you see this message and you are not debugging    **
[    0.000000] ** the kernel, report this immediately to your system   **
[    0.000000] ** administrator!                                       **
[    0.000000] **                                                      **
[    0.000000] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
[    0.000000] **********************************************************
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    0.000000] NR_IRQS: 512, nr_irqs: 512, preallocated irqs: 16
[    0.000000] mpic: Resetting
[    0.000000] mpic: Setting up MPIC " MPIC 1   " version 1.2 at 80040000, max 2 CPUs
[    0.000000] mpic: ISU size: 64, shift: 6, mask: 3f
[    0.000000] mpic: Initializing for 64 sources
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] time_init: decrementer frequency = 41.658676 MHz
[    0.000000] time_init: processor frequency   = 1416.666661 MHz
[    0.000009] clocksource: timebase: mask: 0xffffffffffffffff max_cycles: 0x99b9699db, max_idle_ns: 440795204297 ns
[    0.000563] clocksource: timebase mult[18012db2] shift[24] registered
[    0.001063] clockevent: decrementer mult[aaa249b] shift[32] cpu[0]
[    0.003853] Console: colour dummy device 80x25
[    0.004327] printk: console [tty0] enabled
[    0.004842] printk: bootconsole [udbg0] disabled
[    0.006004] pid_max: default: 32768 minimum: 301
[    0.012202] LSM: initializing lsm=capability,yama
[    0.012296] Yama: becoming mindful.
[    0.014232] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.014419] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.029435] PowerMac SMP probe found 2 cpus
[    0.030204] KeyWest i2c @0xf8001003 irq 42 /uni-n@f8000000/i2c@f8001000
[    0.030370]  channel 0 bus <multibus>
[    0.030480]  channel 1 bus <multibus>
[    0.030838] KeyWest i2c @0x80018000 irq 26 /pci@f2000000/mac-io@17/i2c@18000
[    0.030989]  channel 0 bus <multibus>
[    0.031126] PMU i2c /pci@f2000000/mac-io@17/via-pmu@16000/pmu-i2c
[    0.031265]  channel 1 bus <multibus>
[    0.031372]  channel 2 bus <multibus>
[    0.031443] pmf: no parser for command 17 !
[    0.031602] Processor timebase sync using GPIO 0x73
[    0.031638] mpic: requesting IPIs...
[    0.032050] CPU0: L2CR is 80000000
[    0.032084] CPU0: L3CR is 9c030000
[    0.038044] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1.
[    0.039347] MPC7450 family performance monitor hardware support registered
[    0.040280] rcu: Hierarchical SRCU implementation.
[    0.040329] rcu: 	Max phase no-delay instances is 1000.
[    0.043228] smp: Bringing up secondary CPUs ...
[84919679.159678] CPU1: L2CR was 0
[84919679.159763] CPU1: L2CR set to 80000000
[84919679.159776] CPU1: L3CR was 0
[84919679.159926] CPU1: L3CR set to 9c030000
[    0.049914] smp: Brought up 1 node, 2 CPUs
[    0.055674] devtmpfs: initialized
[    0.059277] Duplicate name in PowerPC,G4@0, renamed to "l2-cache#1"
[    0.059821] Duplicate name in l2-cache#1, renamed to "l2-cache#1"
[    0.062151] Duplicate name in PowerPC,G4@1, renamed to "l2-cache#1"
[    0.062726] Duplicate name in l2-cache#1, renamed to "l2-cache#1"
[    0.088705] Duplicate name in gpio@50, renamed to "gpio5@6f#1"
[    0.089135] Duplicate name in gpio@50, renamed to "gpio6@70#1"
[    0.090033] Duplicate name in gpio@50, renamed to "gpio11@75#1"
[    0.090554] Duplicate name in gpio@50, renamed to "extint-gpio15@67#1"
[    0.127856] Found UniNorth PCI host bridge at 0x00000000f0000000. Firmware bus number: 0->0
[    0.127966] PCI host bridge /pci@f0000000  ranges:
[    0.128066]  MEM 0x00000000f1000000..0x00000000f1ffffff -> 0x00000000f1000000 
[    0.128144]   IO 0x00000000f0000000..0x00000000f07fffff -> 0x0000000000000000
[    0.147499]  MEM 0x0000000090000000..0x00000000afffffff -> 0x0000000090000000 
[    0.147891] Found UniNorth PCI host bridge at 0x00000000f2000000. Firmware bus number: 0->0
[    0.147953] PCI host bridge /pci@f2000000 (primary) ranges:
[    0.148049]  MEM 0x00000000f3000000..0x00000000f3ffffff -> 0x00000000f3000000 
[    0.148125]   IO 0x00000000f2000000..0x00000000f27fffff -> 0x0000000000000000
[    0.167612]  MEM 0x0000000080000000..0x000000008fffffff -> 0x0000000080000000 
[    0.168556] Found UniNorth PCI host bridge at 0x00000000f4000000. Firmware bus number: 0->0
[    0.168628] PCI host bridge /pci@f4000000  ranges:
[    0.168723]  MEM 0x00000000f5000000..0x00000000f5ffffff -> 0x00000000f5000000 
[    0.168787]   IO 0x00000000f4000000..0x00000000f47fffff -> 0x0000000000000000
[    0.188694] Found NEC PD720100A USB2 chip with disabled EHCI, fixing up...
[    0.190857] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.191224] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.193641] prandom: seed boundary self test passed
[    0.201497] prandom: 100 self tests passed
[    0.209019] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.244173] PCI: Probing PCI hardware
[    0.246922] PCI host bridge to bus 0000:00
[    0.247006] pci_bus 0000:00: root bus resource [io  0xff780000-0xfff7ffff] (bus address [0x0000-0x7fffff])
[    0.247088] pci_bus 0000:00: root bus resource [mem 0xf1000000-0xf1ffffff]
[    0.247151] pci_bus 0000:00: root bus resource [mem 0x90000000-0xafffffff]
[    0.247271] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.247326] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to ff
[    0.248990] pci 0000:00:0b.0: [106b:0034] type 00 class 0x060000
[    0.251293] pci 0000:00:10.0: [1002:4150] type 00 class 0x030000
[    0.251385] pci 0000:00:10.0: reg 0x10: [mem 0xa0000000-0xafffffff pref]
[    0.251450] pci 0000:00:10.0: reg 0x14: [io  0xff780400-0xff7804ff]
[    0.251509] pci 0000:00:10.0: reg 0x18: [mem 0x90000000-0x9000ffff]
[    0.251595] pci 0000:00:10.0: reg 0x30: [mem 0x90020000-0x9003ffff pref]
[    0.251724] pci 0000:00:10.0: supports D1 D2
[    0.255524] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.258247] OF: /pci@f2000000/mac-io@17/gpio@50/gpio5@6f: could not find phandle 1751474532
[    0.258430] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio15@67: could not find phandle 1751474532
[    0.258629] OF: /pci@f2000000/mac-io@17/gpio@50/gpio6@70: could not find phandle 1634562093
[    0.258798] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio16@68: could not find phandle 1936745825
[    0.259001] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio14@66: could not find phandle 1818848869
[    0.259195] OF: /pci@f2000000/mac-io@17/gpio@50/gpio12@76: could not find phandle 1835103092
[    0.259354] OF: /pci@f2000000/mac-io@17/gpio@50/gpio11@75: could not find phandle 1635083369
[    0.259505] OF: /pci@f2000000/mac-io@17/gpio@50/gpio5@6f: could not find phandle 1751474532
[    0.259654] OF: /pci@f2000000/mac-io@17/gpio@50/gpio6@70: could not find phandle 1634562093
[    0.259804] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio4@5c: could not find phandle 1818848869
[    0.259997] OF: /pci@f2000000/mac-io@17/gpio@50/gpio11@75: could not find phandle 1635083369
[    0.260148] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio15@67: could not find phandle 1751474532
[    0.263719] pci_bus 0001:00: Fixed dependency cycle(s) with /pci@f2000000/mac-io@17/interrupt-controller@40000
[    0.264001] PCI host bridge to bus 0001:00
[    0.264054] pci_bus 0001:00: root bus resource [io  0x0000-0x7fffff]
[    0.264117] pci_bus 0001:00: root bus resource [mem 0xf3000000-0xf3ffffff]
[    0.264205] pci_bus 0001:00: root bus resource [mem 0x80000000-0x8fffffff]
[    0.264272] pci_bus 0001:00: root bus resource [bus 00-ff]
[    0.264321] pci_bus 0001:00: busn_res: [bus 00-ff] end is updated to ff
[    0.265938] pci 0001:00:0b.0: [106b:0035] type 00 class 0x060000
[    0.268845] pci 0001:00:12.0: [1033:0035] type 00 class 0x0c0310
[    0.268935] pci 0001:00:12.0: reg 0x10: [mem 0x8008c000-0x8008cfff]
[    0.269097] pci 0001:00:12.0: supports D1 D2
[    0.269140] pci 0001:00:12.0: PME# supported from D0 D1 D2 D3hot
[    0.271282] pci 0001:00:12.1: [1033:0035] type 00 class 0x0c0310
[    0.271368] pci 0001:00:12.1: reg 0x10: [mem 0x8008b000-0x8008bfff]
[    0.271530] pci 0001:00:12.1: supports D1 D2
[    0.271572] pci 0001:00:12.1: PME# supported from D0 D1 D2 D3hot
[    0.273698] pci 0001:00:12.2: [1033:00e0] type 00 class 0x0c0320
[    0.273781] pci 0001:00:12.2: reg 0x10: [mem 0x80081000-0x800810ff]
[    0.273941] pci 0001:00:12.2: supports D1 D2
[    0.273983] pci 0001:00:12.2: PME# supported from D0 D1 D2 D3hot
[    0.275508] pci 0001:00:13.0: [1095:3112] type 00 class 0x018000
[    0.275589] pci 0001:00:13.0: reg 0x10: [io  0x0460-0x0467]
[    0.275645] pci 0001:00:13.0: reg 0x14: [io  0x0450-0x0453]
[    0.275700] pci 0001:00:13.0: reg 0x18: [io  0x0440-0x0447]
[    0.275755] pci 0001:00:13.0: reg 0x1c: [io  0x0430-0x0433]
[    0.275809] pci 0001:00:13.0: reg 0x20: [io  0x0420-0x042f]
[    0.275864] pci 0001:00:13.0: reg 0x24: [mem 0x80082000-0x800821ff]
[    0.275922] pci 0001:00:13.0: reg 0x30: [mem 0x80100000-0x8017ffff pref]
[    0.276039] pci 0001:00:13.0: supports D1 D2
[    0.278351] pci 0001:00:15.0: [9710:9865] type 00 class 0x070002
[    0.278440] pci 0001:00:15.0: reg 0x10: [io  0x0410-0x0417]
[    0.278499] pci 0001:00:15.0: reg 0x14: [mem 0x8008a000-0x8008afff]
[    0.278571] pci 0001:00:15.0: reg 0x20: [mem 0x80089000-0x80089fff]
[    0.278706] pci 0001:00:15.0: supports D1 D2
[    0.278748] pci 0001:00:15.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.280272] pci 0001:00:15.1: [9710:9865] type 00 class 0x070002
[    0.280353] pci 0001:00:15.1: reg 0x10: [io  0x0400-0x0407]
[    0.280410] pci 0001:00:15.1: reg 0x14: [mem 0x80088000-0x80088fff]
[    0.280482] pci 0001:00:15.1: reg 0x20: [mem 0x80087000-0x80087fff]
[    0.280615] pci 0001:00:15.1: supports D1 D2
[    0.280656] pci 0001:00:15.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.283437] pci 0001:00:15.2: [ffff:9865] type 00 class 0x070103
[    0.283524] pci 0001:00:15.2: reg 0x10: [io  0x0000-0x0007]
[    0.283581] pci 0001:00:15.2: reg 0x14: [io  0x0000-0x0007]
[    0.283637] pci 0001:00:15.2: reg 0x18: [mem 0x00000000-0x00000fff]
[    0.283701] pci 0001:00:15.2: reg 0x20: [mem 0x00000000-0x00000fff]
[    0.283834] pci 0001:00:15.2: supports D1 D2
[    0.283876] pci 0001:00:15.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.285354] pci 0001:00:16.0: [14e4:4320] type 00 class 0x028000
[    0.285435] pci 0001:00:16.0: reg 0x10: [mem 0x8008e000-0x8008ffff]
[    0.285591] pci 0001:00:16.0: supports D1 D2
[    0.285633] pci 0001:00:16.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.287666] pci 0001:00:17.0: [106b:0022] type 00 class 0xff0000
[    0.287785] pci 0001:00:17.0: reg 0x10: [mem 0x80000000-0x8007ffff]
[    0.289587] pci 0001:00:18.0: [106b:0019] type 00 class 0x0c0310
[    0.289669] pci 0001:00:18.0: reg 0x10: [mem 0x80086000-0x80086fff]
[    0.291832] pci 0001:00:19.0: [106b:0019] type 00 class 0x0c0310
[    0.291915] pci 0001:00:19.0: reg 0x10: [mem 0x80085000-0x80085fff]
[    0.294103] pci 0001:00:1b.0: [1033:0035] type 00 class 0x0c0310
[    0.294190] pci 0001:00:1b.0: reg 0x10: [mem 0x80084000-0x80084fff]
[    0.294351] pci 0001:00:1b.0: supports D1 D2
[    0.294393] pci 0001:00:1b.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.296609] pci 0001:00:1b.1: [1033:0035] type 00 class 0x0c0310
[    0.296694] pci 0001:00:1b.1: reg 0x10: [mem 0x80083000-0x80083fff]
[    0.296854] pci 0001:00:1b.1: supports D1 D2
[    0.296896] pci 0001:00:1b.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.298523] pci 0001:00:1b.2: [1033:00e0] type 00 class 0x0c0320
[    0.298603] pci 0001:00:1b.2: reg 0x10: [mem 0x80080000-0x800800ff]
[    0.298763] pci 0001:00:1b.2: supports D1 D2
[    0.298805] pci 0001:00:1b.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.301130] pci_bus 0001:00: busn_res: [bus 00-ff] end is updated to 00
[    0.306768] PCI host bridge to bus 0002:00
[    0.306847] pci_bus 0002:00: root bus resource [io  0x880000-0x107ffff] (bus address [0x0000-0x7fffff])
[    0.306924] pci_bus 0002:00: root bus resource [mem 0xf5000000-0xf5ffffff]
[    0.306990] pci_bus 0002:00: root bus resource [bus 00-ff]
[    0.307040] pci_bus 0002:00: busn_res: [bus 00-ff] end is updated to ff
[    0.308687] pci 0002:00:0b.0: [106b:0036] type 00 class 0x060000
[    0.310877] pci 0002:00:0d.0: [106b:0033] type 00 class 0xff0000
[    0.310961] pci 0002:00:0d.0: reg 0x10: [mem 0xf5004000-0xf5007fff]
[    0.313149] pci 0002:00:0e.0: [106b:0031] type 00 class 0x0c0010
[    0.313234] pci 0002:00:0e.0: reg 0x10: [mem 0xf5000000-0xf5000fff]
[    0.313387] pci 0002:00:0e.0: supports D1 D2
[    0.313429] pci 0002:00:0e.0: PME# supported from D0 D1 D2 D3hot
[    0.315519] pci 0002:00:0f.0: [106b:0032] type 00 class 0x020000
[    0.315602] pci 0002:00:0f.0: reg 0x10: [mem 0xf5200000-0xf53fffff]
[    0.315705] pci 0002:00:0f.0: reg 0x30: [mem 0xf5100000-0xf51fffff pref]
[    0.318996] pci_bus 0002:00: busn_res: [bus 00-ff] end is updated to 00
[    0.320483] PCI 0000:00 Cannot reserve Legacy IO [io  0xff780000-0xff780fff]
[    0.320564] PCI 0001:00 Cannot reserve Legacy IO [io  0x0000-0x0fff]
[    0.320642] pci_bus 0000:00: resource 4 [io  0xff780000-0xfff7ffff]
[    0.320695] pci_bus 0000:00: resource 5 [mem 0xf1000000-0xf1ffffff]
[    0.320744] pci_bus 0000:00: resource 6 [mem 0x90000000-0xafffffff]
[    0.320860] pci 0001:00:15.2: BAR 2: assigned [mem 0xf3000000-0xf3000fff]
[    0.320924] pci 0001:00:15.2: BAR 4: assigned [mem 0xf3001000-0xf3001fff]
[    0.320985] pci 0001:00:15.2: BAR 0: assigned [io  0x1000-0x1007]
[    0.321042] pci 0001:00:15.2: BAR 1: assigned [io  0x1008-0x100f]
[    0.321119] pci_bus 0001:00: resource 4 [io  0x0000-0x7fffff]
[    0.321167] pci_bus 0001:00: resource 5 [mem 0xf3000000-0xf3ffffff]
[    0.321216] pci_bus 0001:00: resource 6 [mem 0x80000000-0x8fffffff]
[    0.321271] pci_bus 0002:00: resource 4 [io  0x880000-0x107ffff]
[    0.321319] pci_bus 0002:00: resource 5 [mem 0xf5000000-0xf5ffffff]
[    0.398995] raid6: altivecx8 gen()   550 MB/s
[    0.455808] raid6: altivecx4 gen()   537 MB/s
[    0.512645] raid6: altivecx2 gen()   480 MB/s
[    0.569483] raid6: altivecx1 gen()   385 MB/s
[    0.626384] raid6: int32x8  gen()   140 MB/s
[    0.683232] raid6: int32x4  gen()   135 MB/s
[    0.739974] raid6: int32x2  gen()   118 MB/s
[    0.796788] raid6: int32x1  gen()    94 MB/s
[    0.796825] raid6: using algorithm altivecx8 gen() 550 MB/s
[    0.796862] raid6: using intx1 recovery algorithm
[    0.809786] SCSI subsystem initialized
[    0.812998] libata version 3.00 loaded.
[    0.815073] usbcore: registered new interface driver usbfs
[    0.815612] usbcore: registered new interface driver hub
[    0.816872] usbcore: registered new device driver usb
[    0.833638] pci 0000:00:10.0: vgaarb: setting as boot VGA device
[    0.833721] pci 0000:00:10.0: vgaarb: bridge control possible
[    0.833764] pci 0000:00:10.0: vgaarb: VGA device added: decodes=io+mem,owns=mem,locks=none
[    0.833884] vgaarb: loaded
[    0.835391] clocksource: Switched to clocksource timebase
[    0.964372] NET: Registered PF_INET protocol family
[    0.967488] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.976190] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 10240 bytes, linear)
[    0.980617] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.982800] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.991932] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear)
[    0.994271] TCP: Hash tables configured (established 8192 bind 8192)
[    0.997514] UDP hash table entries: 512 (order: 2, 24576 bytes, linear)
[    0.998304] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes, linear)
[    1.000422] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    1.001928] pci 0001:00:12.0: enabling device (0000 -> 0002)
[    1.002245] pci 0001:00:12.1: enabling device (0000 -> 0002)
[    1.002388] pci 0001:00:12.2: enabling device (0004 -> 0006)
[    1.002661] Apple USB OHCI 0001:00:18.0 disabled by firmware
[    1.002706] pci 0001:00:18.0: Can't enable PCI device, BIOS handoff failed.
[    1.002776] Apple USB OHCI 0001:00:19.0 disabled by firmware
[    1.002815] pci 0001:00:19.0: Can't enable PCI device, BIOS handoff failed.
[    1.002894] pci 0001:00:1b.0: enabling device (0000 -> 0002)
[    1.003020] pci 0001:00:1b.1: enabling device (0000 -> 0002)
[    1.003215] pci 0001:00:1b.2: enabling device (0004 -> 0006)
[    1.003410] pci 0002:00:0f.0: CLS mismatch (32 != 1020), using 32 bytes
[    1.004677] Thermal assist unit not available
[    1.018846] Initialise system trusted keyrings
[    1.020481] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[    1.048287] fuse: init (API version 7.38)
[    1.051170] 9p: Installing v9fs 9p2000 file system support
[    1.053362] NET: Registered PF_ALG protocol family
[    1.053704] xor: measuring software checksum speed
[    1.131507]    8regs           :   126 MB/sec
[    1.209945]    8regs_prefetch  :   125 MB/sec
[    1.289038]    32regs          :   124 MB/sec
[    1.369052]    32regs_prefetch :   123 MB/sec
[    1.389003]    altivec         :   494 MB/sec
[    1.389042] xor: using function: altivec (494 MB/sec)
[    1.389155] Key type asymmetric registered
[    1.389197] Asymmetric key parser 'x509' registered
[    1.416987] bounce: pool size: 64 pages
[    1.418911] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.418984] io scheduler kyber registered
[    1.419584] io scheduler bfq registered
[    1.450236] MacIO PCI driver attached to Keylargo chipset
[    1.473353] 0.00013020:ch-a: ttyS0 at MMIO 0x80013020 (irq = 22, base_baud = 230400) is a Z85c30 ESCC - Serial port
[    1.482737] 0.00013000:ch-b: ttyS1 at MMIO 0x80013000 (irq = 23, base_baud = 230400) is a Z85c30 ESCC - Serial port
[    1.503344] sata_sil 0001:00:13.0: version 2.4
[    1.504170] sata_sil 0001:00:13.0: enabling device (0004 -> 0007)
[    1.516131] scsi host0: sata_sil
[    1.523680] scsi host1: sata_sil
[    1.526387] ata1: SATA max UDMA/100 mmio m512@0x80082000 tf 0x80082080 irq 53
[    1.526451] ata2: SATA max UDMA/100 mmio m512@0x80082000 tf 0x800820c0 irq 53
[    1.528435] pata-pci-macio 0002:00:0d.0: enabling device (0004 -> 0006)
[    1.545451] pata-pci-macio 0002:00:0d.0: Activating pata-macio chipset UniNorth ATA-6, Apple bus ID 3
[    1.554727] scsi host2: pata_macio
[    1.557742] ata3: PATA max UDMA/100 irq 39
[    1.838817] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[    1.841791] ata1.00: ATA-9: SanDisk SSD PLUS 240GB, UF4500RL, max UDMA/133
[    1.841852] ata1.00: 468877312 sectors, multi 1: LBA48 NCQ (depth 0/32)
[    1.843322] ata1.00: Features: Dev-Sleep
[    1.866995] ata1.00: configured for UDMA/100
[    1.868564] scsi 0:0:0:0: Direct-Access     ATA      SanDisk SSD PLUS 00RL PQ: 0 ANSI: 5
[    1.879832] sd 0:0:0:0: [sda] 468877312 512-byte logical blocks: (240 GB/224 GiB)
[    1.880110] sd 0:0:0:0: [sda] Write Protect is off
[    1.880184] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.880538] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.881198] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[    1.892160]  sda: [mac] sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8
[    1.906865] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.305438] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[    2.308017] ata2.00: ATA-9: WDC WD5000LPLX-60ZNTT1, 02.01A02, max UDMA/133
[    2.308079] ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[    2.310748] ata2.00: configured for UDMA/100
[    2.311876] scsi 1:0:0:0: Direct-Access     ATA      WDC WD5000LPLX-6 1A02 PQ: 0 ANSI: 5
[    2.320517] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[    2.320629] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[    2.320874] sd 1:0:0:0: [sdb] Write Protect is off
[    2.320947] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    2.321477] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.321972] sd 1:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes
[    2.595436] pata-macio 0.0001f000:ata-4: Activating pata-macio chipset KeyLargo ATA-4, Apple bus ID 2
[    2.605890] scsi host3: pata_macio
[    2.608627] ata4: PATA max UDMA/66 irq 19
[    2.768188] ata4.00: CFA: DeLOCK 54143 512MB, 100511E, max UDMA/66
[    2.768274] ata4.00: 1009008 sectors, multi 1: LBA 
[    3.073418]  sdb: [mac] sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8
[    3.088131] sd 1:0:0:0: [sdb] Attached SCSI disk
[    3.090326] scsi 3:0:0:0: Direct-Access     ATA      DeLOCK 54143 512 11E  PQ: 0 ANSI: 5
[    3.099307] sd 3:0:0:0: [sdc] 1009008 512-byte logical blocks: (517 MB/493 MiB)
[    3.099756] sd 3:0:0:0: [sdc] Write Protect is off
[    3.099830] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[    3.100205] sd 3:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    3.100705] sd 3:0:0:0: [sdc] Preferred minimum I/O size 512 bytes
[    3.110844]  sdc: [mac] sdc1 sdc2 sdc3 sdc4 sdc5 sdc6
[    3.123827] sd 3:0:0:0: [sdc] Attached SCSI disk
[    3.635428] pata-macio 0.00020000:ata-3: Activating pata-macio chipset KeyLargo ATA-3, Apple bus ID 0
[    3.645059] scsi host4: pata_macio
[    3.647746] ata5: PATA max MWDMA2 irq 20
[    3.649606] tun: Universal TUN/TAP device driver, 1.6
[    3.652817] sungem.c:v1.0 David S. Miller <davem@redhat.com>
[    3.665089] gem 0002:00:0f.0 eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0a:95:9c:76:3a
[    3.670727] ehci-pci 0001:00:12.2: EHCI Host Controller
[    3.670930] ehci-pci 0001:00:12.2: new USB bus registered, assigned bus number 1
[    3.672957] ehci-pci 0001:00:12.2: irq 52, io mem 0x80081000
[    3.675594] rtc-generic rtc-generic: registered as rtc0
[    3.678116] PowerMac i2c bus pmu 2 registered
[    3.680113] PowerMac i2c bus pmu 1 registered
[    3.684561] PowerMac i2c bus mac-io 0 registered
[    3.685458] ehci-pci 0001:00:12.2: USB 2.0 started, EHCI 1.00
[    3.686038] i2c i2c-2: No i2c address for /pci@f2000000/mac-io@17/i2c@18000/i2c-modem
[    3.687257] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[    3.687341] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.687393] usb usb1: Product: EHCI Host Controller
[    3.687434] usb usb1: Manufacturer: Linux 6.5.0-rc6-PMacG4-dirty ehci_hcd
[    3.687479] usb usb1: SerialNumber: 0001:00:12.2
[    3.688010] PowerMac i2c bus uni-n 1 registered
[    3.688096] i2c i2c-3: i2c-powermac: modalias failure on /uni-n@f8000000/i2c@f8001000/cereal@1c0
[    3.691147] PowerMac i2c bus uni-n 0 registered
[    3.692285] hub 1-0:1.0: USB hub found
[    3.692572] hub 1-0:1.0: 5 ports detected
[    3.699522] hid: raw HID events driver (C) Jiri Kosina
[    3.701102] ehci-pci 0001:00:1b.2: EHCI Host Controller
[    3.701377] ehci-pci 0001:00:1b.2: new USB bus registered, assigned bus number 2
[    3.702253] ehci-pci 0001:00:1b.2: irq 63, io mem 0x80080000
[    3.702886] usbcore: registered new interface driver usbhid
[    3.702953] usbhid: USB HID core driver
[    3.708553] NET: Registered PF_INET6 protocol family
[    3.718769] ehci-pci 0001:00:1b.2: USB 2.0 started, EHCI 1.00
[    3.719541] Segment Routing with IPv6
[    3.721327] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[    3.721337] In-situ OAM (IOAM) with IPv6
[    3.721355] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.721471] usb usb2: Product: EHCI Host Controller
[    3.721512] usb usb2: Manufacturer: Linux 6.5.0-rc6-PMacG4-dirty ehci_hcd
[    3.721557] usb usb2: SerialNumber: 0001:00:1b.2
[    3.721866] NET: Registered PF_PACKET protocol family
[    3.721962] NET: Registered PF_KEY protocol family
[    3.723965] 9pnet: Installing 9P2000 support
[    3.726774] drmem: No dynamic reconfiguration memory found
[    3.727471] hub 2-0:1.0: USB hub found
[    3.727747] hub 2-0:1.0: 5 ports detected
[    3.808022] ata5.00: ATAPI: _NEC DVD_RW ND-3520A, 1.04, max UDMA/33
[    3.816995] scsi 4:0:0:0: CD-ROM            _NEC     DVD_RW ND-3520A  1.04 PQ: 0 ANSI: 5
[    3.890035] Loading compiled-in X.509 certificates
[    3.942133] sr 4:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[    3.942270] cdrom: Uniform CD-ROM driver Revision: 3.20
[    3.952088] usb 1-3: new high-speed USB device number 2 using ehci-pci
[    3.964022] sr 4:0:0:0: Attached scsi CD-ROM sr0
[    4.002346] zswap: loaded using pool zstd/z3fold
[    4.111383] usb 1-3: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=32.98
[    4.111477] usb 1-3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    4.111525] usb 1-3: Product: USB2.0 Hub
[    4.115107] debug_vm_pgtable: [debug_vm_pgtable         ]: Validating architecture page table helpers
[    4.116296] hub 1-3:1.0: USB hub found
[    4.116867] hub 1-3:1.0: 4 ports detected
[    4.224947] Btrfs loaded, zoned=no, fsverity=no
[    4.405407] usb 1-3.1: new low-speed USB device number 3 using ehci-pci
[    4.531375] usb 1-3.1: New USB device found, idVendor=04d9, idProduct=0006, bcdDevice= 1.40
[    4.531453] usb 1-3.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.531506] usb 1-3.1: Product: RPI Wired Keyboard 5
[    4.531546] usb 1-3.1: Manufacturer:  
[    4.557612] input:   RPI Wired Keyboard 5 as /devices/pci0001:00/0001:00:12.2/usb1/1-3/1-3.1/1-3.1:1.0/0003:04D9:0006.0001/input/input0
[    4.623463] hid-generic 0003:04D9:0006.0001: input,hidraw0: USB HID v1.11 Keyboard [  RPI Wired Keyboard 5] on usb-0001:00:12.2-3.1/input0
[    4.651473] input:   RPI Wired Keyboard 5 as /devices/pci0001:00/0001:00:12.2/usb1/1-3/1-3.1/1-3.1:1.1/0003:04D9:0006.0002/input/input1
[    4.709291] hid-generic 0003:04D9:0006.0002: input,hidraw1: USB HID v1.11 Device [  RPI Wired Keyboard 5] on usb-0001:00:12.2-3.1/input1
[    4.785422] usb 1-3.4: new low-speed USB device number 4 using ehci-pci
[    4.886660] usb 1-3.4: New USB device found, idVendor=275d, idProduct=0ba6, bcdDevice= 1.00
[    4.886739] usb 1-3.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    4.886793] usb 1-3.4: Product: USB OPTICAL MOUSE 
[    4.901926] input: USB OPTICAL MOUSE  as /devices/pci0001:00/0001:00:12.2/usb1/1-3/1-3.4/1-3.4:1.0/0003:275D:0BA6.0003/input/input2
[    4.912924] hid-generic 0003:275D:0BA6.0003: input,hidraw2: USB HID v1.11 Mouse [USB OPTICAL MOUSE ] on usb-0001:00:12.2-3.4/input0
[   10.088141] input: PMU as /devices/virtual/input/input3
[   10.090384] netpoll: netconsole: local port 6666
[   10.090440] netpoll: netconsole: local IPv4 address 192.168.178.8
[   10.090488] netpoll: netconsole: interface 'eth0'
[   10.090521] netpoll: netconsole: remote port 6666
[   10.090555] netpoll: netconsole: remote IPv4 address 192.168.178.3
[   10.090595] netpoll: netconsole: remote ethernet address 70:85:c2:30:ec:01
[   10.090646] netpoll: netconsole: device eth0 not up yet, forcing it
[   10.195821] sungem_phy: PHY ID: 2060e1, addr: 0
[   10.196137] gem 0002:00:0f.0 eth0: Found BCM5421 PHY
[   13.875744] gem 0002:00:0f.0 eth0: Link is up at 1000 Mbps, full-duplex
[   13.875948] gem 0002:00:0f.0 eth0: Pause is enabled (rxfifo: 10240 off: 7168 on: 5632)
[   13.887578] printk: console [netcon0] enabled
[   13.927078] netconsole: network logging started
[   14.126229] EXT4-fs (sda5): mounted filesystem 28419c7c-4bc4-4922-bdc8-6d8515c62385 ro with ordered data mode. Quota mode: disabled.
[   14.126775] VFS: Mounted root (ext4 filesystem) readonly on device 8:5.
[   14.131169] devtmpfs: mounted
[   14.135851] Freeing unused kernel image (initmem) memory: 1344K
[   14.162875] Checked W+X mappings: passed, no W+X pages found
[   14.163028] rodata_test: all tests were successful
[   14.163164] kallsyms_selftest: start
[   14.163210] Run /usr/lib/systemd/systemd as init process
[   14.163664]   with arguments:
[   14.163768]     /usr/lib/systemd/systemd
[   14.163846]   with environment:
[   14.163917]     HOME=/
[   14.164013]     TERM=linux
[   14.983377] systemd[1]: systemd 253 running in system mode (+PAM -AUDIT -SELINUX -APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID -CURL +ELFUTILS -FIDO2 +IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 +LZ4 -XZ -ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP -SYSVINIT default-hierarchy=unified)
[   14.983810] systemd[1]: Detected architecture ppc.
[   15.010679] systemd[1]: Hostname set to <T600>.
[   15.193312] memfd_create() without MFD_EXEC nor MFD_NOEXEC_SEAL, pid=1 'systemd'
[   17.762463] systemd[1]: Queued start job for default target graphical.target.
[   17.986231] systemd[1]: Created slice system-getty.slice.
[   18.001761] systemd[1]: Created slice system-modprobe.slice.
[   18.015677] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[   18.029065] systemd[1]: Created slice system-vncserver.slice.
[   18.042292] systemd[1]: Created slice user.slice.
[   18.047951] systemd[1]: Started systemd-ask-password-console.path.
[   18.053103] systemd[1]: Started systemd-ask-password-wall.path.
[   18.064375] systemd[1]: Set up automount proc-sys-fs-binfmt_misc.automount.
[   18.066271] systemd[1]: Reached target paths.target.
[   18.067592] systemd[1]: Reached target remote-fs.target.
[   18.069496] systemd[1]: Reached target slices.target.
[   18.094441] systemd[1]: Listening on systemd-coredump.socket.
[   18.103691] systemd[1]: Listening on systemd-journald-dev-log.socket.
[   18.111411] systemd[1]: Listening on systemd-journald.socket.
[   18.121814] systemd[1]: Listening on systemd-udevd-control.socket.
[   18.129530] systemd[1]: Listening on systemd-udevd-kernel.socket.
[   18.137273] systemd[1]: dev-hugepages.mount was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/mm/hugepages).
[   18.170457] systemd[1]: Mounting dev-mqueue.mount...
[   18.240431] systemd[1]: Mounting sys-kernel-debug.mount...
[   18.249997] systemd[1]: sys-kernel-tracing.mount was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/tracing).
[   18.324425] systemd[1]: Starting kmod-static-nodes.service...
[   18.426849] systemd[1]: Starting modprobe@configfs.service...
[   18.497530] systemd[1]: Starting modprobe@dm_mod.service...
[   18.580277] systemd[1]: Starting modprobe@drm.service...
[   18.671877] systemd[1]: Starting modprobe@fuse.service...
[   18.673811] device-mapper: uevent: version 1.0.3
[   18.692600] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[   18.747328] systemd[1]: Starting modprobe@loop.service...
[   18.817468] systemd[1]: Starting systemd-fsck-root.service...
[   18.998626] systemd[1]: Starting systemd-journald.service...
[   19.017816] loop: module loaded
[   19.124742] systemd[1]: Starting systemd-modules-load.service...
[   19.266478] systemd[1]: Starting systemd-udev-trigger.service...
[   19.662289] systemd-journald[106]: Collecting audit messages is disabled.
[   19.773069] systemd[1]: Mounted dev-mqueue.mount.
[   19.789355] systemd[1]: Mounted sys-kernel-debug.mount.
[   19.811297] systemd[1]: Finished kmod-static-nodes.service.
[   19.866568] systemd[1]: modprobe@configfs.service: Deactivated successfully.
[   19.879141] systemd[1]: Finished modprobe@configfs.service.
[   19.919757] systemd[1]: modprobe@dm_mod.service: Deactivated successfully.
[   19.994150] systemd[1]: Finished modprobe@dm_mod.service.
[   20.086316] systemd[1]: modprobe@drm.service: Deactivated successfully.
[   20.091521] systemd[1]: Finished modprobe@drm.service.
[   20.262530] systemd[1]: modprobe@fuse.service: Deactivated successfully.
[   20.279339] systemd[1]: Finished modprobe@fuse.service.
[   20.375787] systemd[1]: modprobe@loop.service: Deactivated successfully.
[   20.385978] systemd[1]: Finished modprobe@loop.service.
[   20.415847] systemd[1]: Finished systemd-fsck-root.service.
[   20.437508] systemd[1]: Finished systemd-modules-load.service.
[   20.536358] systemd[1]: Mounting sys-fs-fuse-connections.mount...
[   20.773227] systemd[1]: Mounting sys-kernel-config.mount...
[   21.081206] systemd[1]: Starting systemd-remount-fs.service...
[   21.099219] systemd[1]: systemd-repart.service was skipped because no trigger condition checks were met.
[   21.258407] systemd[1]: Starting systemd-sysctl.service...
[   21.449574] systemd[1]: Mounted sys-fs-fuse-connections.mount.
[   21.473517] systemd[1]: Mounted sys-kernel-config.mount.
[   22.033775] systemd[1]: Finished systemd-sysctl.service.
[   26.175559] EXT4-fs (sda5): re-mounted 28419c7c-4bc4-4922-bdc8-6d8515c62385 r/w. Quota mode: disabled.
[   26.248271] systemd[1]: Finished systemd-remount-fs.service.
[   26.251077] systemd[1]: systemd-firstboot.service was skipped because of an unmet condition check (ConditionFirstBoot=yes).
[   26.273853] systemd[1]: systemd-hwdb-update.service was skipped because of an unmet condition check (ConditionNeedsUpdate=/etc).
[   26.411344] systemd[1]: Starting systemd-random-seed.service...
[   26.415191] systemd[1]: systemd-sysusers.service was skipped because no trigger condition checks were met.
[   26.521335] systemd[1]: Starting systemd-tmpfiles-setup-dev.service...
[   26.782194] systemd[1]: Started systemd-journald.service.
[   27.246813] systemd-journald[106]: Received client request to flush runtime journal.
[   27.422147] random: crng init done
[   27.437380] systemd-journald[106]: /var/log/journal/71303955349d475c9d69360df5e2c5b5/system.journal: Monotonic clock jumped backwards relative to last journal entry, rotating.
[   27.437614] systemd-journald[106]: Rotating system journal.
[   40.476186] gem 0002:00:0f.0 enP2p0s15: renamed from eth0 (while UP)
[   43.992434] BTRFS: device label g4_musl devid 1 transid 64495 /dev/sda4 scanned by (udev-worker) (130)
[   44.693711] BTRFS: device label tmp devid 1 transid 58 /dev/sda6 scanned by (udev-worker) (133)
[   46.807118] Adding 8388604k swap on /dev/sdb6.  Priority:-2 extents:1 across:8388604k FS
[   49.112311] EXT4-fs (sdc5): mounting ext2 file system using the ext4 subsystem
[   49.153167] EXT4-fs (sdc5): mounted filesystem e4e8af9e-0f0d-44f9-b983-71bf61d782de r/w without journal. Quota mode: disabled.
[   49.153554] ext2 filesystem being mounted at /boot supports timestamps until 2038-01-19 (0x7fffffff)
[   49.164893] kallsyms_selftest:  ---------------------------------------------------------
[   49.165294] kallsyms_selftest: | nr_symbols | compressed size | original size | ratio(%) |
[   49.165506] kallsyms_selftest: |---------------------------------------------------------|
[   49.165613] kallsyms_selftest: |      33826 |        363977   |       629231  |  57.84   |
[   49.165715] kallsyms_selftest:  ---------------------------------------------------------
[   50.821054] ohci-pci 0001:00:12.0: OHCI PCI host controller
[   50.821355] ohci-pci 0001:00:12.0: new USB bus registered, assigned bus number 3
[   50.879084] ohci-pci 0001:00:12.0: irq 52, io mem 0x8008c000
[   51.152211] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.05
[   51.152595] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   51.152767] usb usb3: Product: OHCI PCI host controller
[   51.152895] usb usb3: Manufacturer: Linux 6.5.0-rc6-PMacG4-dirty ohci_hcd
[   51.153024] usb usb3: SerialNumber: 0001:00:12.0
[   51.233906] hub 3-0:1.0: USB hub found
[   51.261806] hub 3-0:1.0: 3 ports detected
[   51.434065] ohci-pci 0001:00:12.1: OHCI PCI host controller
[   51.434354] ohci-pci 0001:00:12.1: new USB bus registered, assigned bus number 4
[   51.435010] ohci-pci 0001:00:12.1: irq 52, io mem 0x8008b000
[   52.011364] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.05
[   52.011574] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   52.011685] usb usb4: Product: OHCI PCI host controller
[   52.011781] usb usb4: Manufacturer: Linux 6.5.0-rc6-PMacG4-dirty ohci_hcd
[   52.011944] usb usb4: SerialNumber: 0001:00:12.1
[   52.136939] hub 4-0:1.0: USB hub found
[   52.138273] hub 4-0:1.0: 2 ports detected
[   52.301902] Apple USB OHCI 0001:00:18.0 disabled by firmware
[   52.302331] Apple USB OHCI 0001:00:19.0 disabled by firmware
[   52.302909] ohci-pci 0001:00:1b.0: OHCI PCI host controller
[   52.303168] ohci-pci 0001:00:1b.0: new USB bus registered, assigned bus number 5
[   52.303943] ohci-pci 0001:00:1b.0: irq 63, io mem 0x80084000
[   52.322245] BTRFS info (device sda6): using xxhash64 (xxhash64-generic) checksum algorithm
[   52.322544] BTRFS info (device sda6): use lzo compression, level 0
[   52.322685] BTRFS info (device sda6): using free space tree
[   52.565635] BTRFS info (device sda6): enabling ssd optimizations
[   52.706558] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.05
[   52.706896] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   52.707049] usb usb5: Product: OHCI PCI host controller
[   52.707149] usb usb5: Manufacturer: Linux 6.5.0-rc6-PMacG4-dirty ohci_hcd
[   52.707249] usb usb5: SerialNumber: 0001:00:1b.0
[   52.757195] hub 5-0:1.0: USB hub found
[   52.933830] hub 5-0:1.0: 3 ports detected
[   53.018146] ohci-pci 0001:00:1b.1: OHCI PCI host controller
[   53.018450] ohci-pci 0001:00:1b.1: new USB bus registered, assigned bus number 6
[   53.029575] ohci-pci 0001:00:1b.1: irq 63, io mem 0x80083000
[   53.136838] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.05
[   53.137053] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   53.137166] usb usb6: Product: OHCI PCI host controller
[   53.137326] usb usb6: Manufacturer: Linux 6.5.0-rc6-PMacG4-dirty ohci_hcd
[   53.137459] usb usb6: SerialNumber: 0001:00:1b.1
[   53.228031] hub 6-0:1.0: USB hub found
[   53.259573] hub 6-0:1.0: 2 ports detected
[   53.535846] b43-pci-bridge 0001:00:16.0: enabling device (0004 -> 0006)
[   53.561856] ssb: Found chip with id 0x4306, rev 0x02 and package 0x00
[   53.659482] b43-pci-bridge 0001:00:16.0: Sonics Silicon Backplane found on PCI device 0001:00:16.0
[   53.863329] kallsyms_selftest: kallsyms_lookup_name() looked up 33826 symbols
[   53.863535] kallsyms_selftest: The time spent on each symbol is (ns): min=5641, max=1747703, avg=98860
[   53.946316] kallsyms_selftest: kallsyms_on_each_symbol() traverse all: 82668478 ns
[   53.946595] kallsyms_selftest: kallsyms_on_each_match_symbol() traverse all: 85504 ns
[   53.946699] kallsyms_selftest: finish
[   55.880588] firewire_ohci 0002:00:0e.0: enabling device (0000 -> 0002)
[   55.958985] firewire_ohci 0002:00:0e.0: added OHCI v1.10 device as card 0, 8 IR + 8 IT contexts, quirks 0x0
[   56.003066] [drm] radeon kernel modesetting enabled.
[   56.003666] radeon 0000:00:10.0: vgaarb: deactivate vga console
[   56.030014] radeon 0000:00:10.0: enabling device (0006 -> 0007)
[   56.090087] [drm] initializing kernel modesetting (RV350 0x1002:0x4150 0x1002:0x0002 0x00).
[   56.090368] [drm] Forcing AGP to PCI mode
[   56.091931] radeon 0000:00:10.0: Invalid PCI ROM header signature: expecting 0xaa55, got 0x0000
[   56.472743] firewire_core 0002:00:0e.0: created device fw0: GUID 000a95fffe9c763a, S800
[   56.612356] [drm] Generation 2 PCI interface, using max accessible memory
[   56.612578] radeon 0000:00:10.0: VRAM: 256M 0x00000000A0000000 - 0x00000000AFFFFFFF (256M used)
[   56.612777] radeon 0000:00:10.0: GTT: 512M 0x0000000080000000 - 0x000000009FFFFFFF
[   56.613067] [drm] Detected VRAM RAM=256M, BAR=256M
[   56.613167] [drm] RAM width 128bits DDR
[   56.654626] [drm] radeon: 256M of VRAM memory ready
[   56.654833] [drm] radeon: 512M of GTT memory ready.
[   56.655303] [drm] GART: num cpu pages 131072, num gpu pages 131072
[   57.059053] [drm] radeon: 1 quad pipes, 1 Z pipes initialized
[   57.059253] [drm] PCI GART of 512M enabled (table at 0x0000000009980000).
[   57.059622] radeon 0000:00:10.0: WB enabled
[   57.059745] radeon 0000:00:10.0: fence driver on ring 0 use gpu addr 0x0000000080000000
[   57.112239] [drm] radeon: irq initialized.
[   57.112926] [drm] Loading R300 Microcode
[   57.338823] ADM1030 fan controller [@2c]
[   57.385553] DS1775 digital thermometer [@49]
[   57.385736] Temp: 58.1 C
[   57.385754]   Hyst: 70.0 C
[   57.385840]   OS: 75.0 C
[   57.385925] 
[   57.591475] [drm] radeon: ring at 0x0000000080001000
[   57.591804] [drm] ring test succeeded in 0 usecs
[   57.713600] [drm] ib test succeeded in 0 usecs
[   57.882111] [drm] Radeon Display Connectors
[   57.882294] [drm] Connector 0:
[   57.882380] [drm]   DVI-I-1
[   57.882461] [drm]   HPD2
[   57.882602] [drm]   DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[   57.882735] [drm]   Encoders:
[   57.882818] [drm]     CRT1: INTERNAL_DAC1
[   57.882904] [drm]     DFP2: INTERNAL_DVO1
[   57.882991] [drm] Connector 1:
[   57.883097] [drm]   DVI-I-2
[   57.883177] [drm]   HPD1
[   57.883254] [drm]   DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[   57.883350] [drm]   Encoders:
[   57.883428] [drm]     CRT2: INTERNAL_DAC2
[   57.883542] [drm]     DFP1: INTERNAL_TMDS1
[   57.884122] [drm] Initialized radeon 2.50.0 20080528 for 0000:00:10.0 on minor 0
[   59.012872] [drm] fb mappable at 0xA0040000
[   59.013149] [drm] vram apper at 0xA0000000
[   59.013329] [drm] size 8294400
[   59.013450] [drm] fb depth is 24
[   59.013563] [drm]    pitch is 7680
[   61.752412] Console: switching to colour frame buffer device 240x67
[   62.932369] radeon 0000:00:10.0: [drm] fb0: radeondrmfb frame buffer device
[   65.581810] CPU-temp: 58.3 C
[   65.581859] , Case: 36.3 C
[   65.582427] ,  Fan: 4 (tuned -7)
[   71.723929] snd-aoa-fabric-layout: Using direct GPIOs
[   71.841944] snd-aoa-fabric-layout: can use this codec
[   71.923846] snd-aoa-codec-tas: tas found, addr 0x35 on /pci@f2000000/mac-io@17/i2c@18000/deq@6a
[   72.845148] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[   73.265942] systemd-journald[106]: /var/log/journal/71303955349d475c9d69360df5e2c5b5/user-1000.journal: Monotonic clock jumped backwards relative to last journal entry, rotating.
[   73.492752] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[   73.496007] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[   73.497514] cfg80211: failed to load regulatory.db
[   74.619985] b43legacy-phy0: Broadcom 4306 WLAN found (core revision 4)
[   74.659028] b43legacy-phy0 debug: Found PHY: Analog 1, Type 2, Revision 1
[   74.660145] b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
[   74.722421] b43legacy-phy0 debug: Radio initialized
[   74.724578] b43legacy-phy0: Loading firmware b43legacy/ucode4.fw
[   74.728404] Broadcom 43xx-legacy driver loaded [ Features: PLID ]
[   74.783776] b43legacy-phy0: Loading firmware b43legacy/pcm4.fw
[   74.814813] b43legacy-phy0: Loading firmware b43legacy/b0g0initvals2.fw
[   74.838866] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   89.878780] CPU-temp: 58.8 C
[   89.878835] , Case: 36.5 C
[   89.879001] ,  Fan: 5 (tuned +1)
[  113.651624] EXT4-fs (sdc5): unmounting filesystem e4e8af9e-0f0d-44f9-b983-71bf61d782de.
[  115.580803] systemd-shutdown[1]: Syncing filesystems and block devices.
[  115.809307] systemd-shutdown[1]: Sending SIGTERM to remaining processes...
[  116.000024] systemd-journald[106]: Received SIGTERM from PID 1 (systemd-shutdow).
[  116.113468] systemd-shutdown[1]: Sending SIGKILL to remaining processes...
[  116.305706] systemd-shutdown[1]: Unmounting file systems.
[  116.380304] (sd-remount)[444]: Remounting '/' read-only with options ''.
[  116.445288] EXT4-fs (sda5): re-mounted 28419c7c-4bc4-4922-bdc8-6d8515c62385 ro. Quota mode: disabled.
[  116.754838] systemd-shutdown[1]: All filesystems unmounted.
[  116.787462] systemd-shutdown[1]: Deactivating swaps.
[  116.820680] systemd-shutdown[1]: All swaps deactivated.
[  116.852814] systemd-shutdown[1]: Detaching loop devices.
[  116.952089] systemd-shutdown[1]: All loop devices detached.
[  116.984847] systemd-shutdown[1]: Stopping MD devices.
[  117.019184] systemd-shutdown[1]: All MD devices stopped.
[  117.051250] systemd-shutdown[1]: Detaching DM devices.
[  117.084799] systemd-shutdown[1]: All DM devices detached.
[  117.117085] systemd-shutdown[1]: All filesystems, swaps, loop devices, MD devices and DM devices detached.
[  117.181428] systemd-shutdown[1]: Syncing filesystems and block devices.
[  117.215800] systemd-shutdown[1]: Powering off.
[  117.249838] sd 3:0:0:0: [sdc] Stopping disk
[  117.283910] sd 1:0:0:0: [sdb] Synchronizing SCSI cache
[  117.317652] sd 1:0:0:0: [sdb] Stopping disk
[  117.657337] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[  117.690922] sd 0:0:0:0: [sda] Stopping disk
[  117.735448] reboot: Power down