linuxppc-dev.lists.ozlabs.org archive mirror
 help / color / mirror / Atom feed
From: Erhard Furtner <erhard_f@mailbox.org>
To: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: "linuxppc-dev@lists.ozlabs.org" <linuxppc-dev@lists.ozlabs.org>
Subject: Re: KASAN debug kernel fails to boot at early stage when CONFIG_SMP=y is set (kernel 6.5-rc5, PowerMac G4 3,6)
Date: Fri, 18 Aug 2023 18:23:16 +0200	[thread overview]
Message-ID: <20230818182316.79303545@yea> (raw)
In-Reply-To: <fcdf2bf7-0834-b27f-4d24-28e05815ee6f@csgroup.eu>

[-- Attachment #1: Type: text/plain, Size: 1251 bytes --]

On Fri, 18 Aug 2023 15:47:38 +0000
Christophe Leroy <christophe.leroy@csgroup.eu> wrote:

> I'm wondering if the problem is just linked to the kernel being built 
> with CONFIG_SMP or if it is the actual startup of a secondary CPU that 
> cause the freeze.
> 
> Please leave the btext_unmap() in place because I think it is important 
> to keep it, and start the kernel with the following parameter:
> 
> nr_cpus=1

With btext_unmap() back and place and nr_cpus=1 set the freeze still happens after the 1st btext_unmap:129 on cold boots:

[    0.000000] printk: bootconsole [udbg0] enabled
[    0.000000] Total memory = 2048MB; using 4096kB for hash table
[    0.000000] mapin_ram:125
[    0.000000] mmu_mapin_ram:169 0 30000000 1400000 2000000
[    0.000000] __mmu_mapin_ram:146 0 1400000
[    0.000000] __mmu_mapin_ram:155 1400000
[    0.000000] __mmu_mapin_ram:146 1400000 30000000
[    0.000000] __mmu_mapin_ram:155 20000000
[    0.000000] __mapin_ram_chunk:107 20000000 30000000
[    0.000000] __mapin_ram_chunk:117
[    0.000000] mapin_ram:134
[    0.000000] kasan_mmu_init:129
[    0.000000] kasan_mmu_init:132 0
[    0.000000] kasan_mmu_init:137
[    0.000000] btext_unmap:129

Attached is warm boot dmesg with nr_cpus=1 set.

Regards,
Erhard

[-- Attachment #2: dmesg_65-rc6_g4_05 --]
[-- Type: application/octet-stream, Size: 49884 bytes --]

[    0.000000] printk: bootconsole [udbg0] enabled
[    0.000000] Total memory = 2048MB; using 4096kB for hash table
[    0.000000] mapin_ram:125
[    0.000000] mmu_mapin_ram:169 0 30000000 1400000 2000000
[    0.000000] __mmu_mapin_ram:146 0 1400000
[    0.000000] __mmu_mapin_ram:155 1400000
[    0.000000] __mmu_mapin_ram:146 1400000 30000000
[    0.000000] __mmu_mapin_ram:155 20000000
[    0.000000] __mapin_ram_chunk:107 20000000 30000000
[    0.000000] __mapin_ram_chunk:117
[    0.000000] mapin_ram:134
[    0.000000] kasan_mmu_init:129
[    0.000000] kasan_mmu_init:132 0
[    0.000000] kasan_mmu_init:137
[    0.000000] btext_unmap:129
[    0.000000] btext_unmap:131
[    0.000000] Linux version 6.5.0-rc6-PMacG4-dirty (root@T1000) (gcc (Gentoo 12.3.1_p20230526 p2) 12.3.1 20230526, GNU ld (Gentoo 2.40 p7) 2.40.0) #8 SMP Fri Aug 18 18:00:44 CEST 2023
[    0.000000] KASAN init done
[    0.000000] ioremap() called early from pmac_feature_init+0x17c/0xe98. Use early_ioremap() instead
[    0.000000] Found UniNorth memory controller & host bridge @ 0xf8000000 revision: 0x24
[    0.000000] Mapped at 0xf53bf000
[    0.000000] ioremap() called early from probe_one_macio+0x1f8/0x400. Use early_ioremap() instead
[    0.000000] Found a Keylargo mac-io controller, rev: 3, mapped at 0x(ptrval)
[    0.000000] PowerMac motherboard: PowerMac G4 Windtunnel
[    0.000000] ioremap() called early from btext_map+0x64/0xdc. Use early_ioremap() instead
[    0.000000] Hardware name: PowerMac3,6 7455 0x80010303 PowerMac
[    0.000000] CPU maps initialized for 1 thread per core
[    0.000000]  (thread shift is 0)
[    0.000000] -----------------------------------------------------
[    0.000000] phys_mem_size     = 0x80000000
[    0.000000] dcache_bsize      = 0x20
[    0.000000] icache_bsize      = 0x20
[    0.000000] cpu_features      = 0x000000002514600a
[    0.000000]   possible        = 0x00000000277de00a
[    0.000000]   always          = 0x0000000001000000
[    0.000000] cpu_user_features = 0x9c000001 0x00000000
[    0.000000] mmu_features      = 0x00010001
[    0.000000] Hash_size         = 0x400000
[    0.000000] Hash_mask         = 0xffff
[    0.000000] -----------------------------------------------------
[    0.000000] ioremap() called early from pmac_setup_arch+0x1ac/0x448. Use early_ioremap() instead
[    0.000000] ioremap() called early from find_via_pmu+0x2a8/0x434. Use early_ioremap() instead
[    0.000000] ioremap() called early from find_via_pmu+0x2e4/0x434. Use early_ioremap() instead
[    0.000000] via-pmu: Server Mode is disabled
[    0.000000] PMU driver v2 initialized for Core99, firmware: 0c
[    0.000000] ioremap() called early from pmac_nvram_init+0x208/0x7c4. Use early_ioremap() instead
[    0.000000] nvram: Checking bank 0...
[    0.000000] nvram: gen0=3202, gen1=3203
[    0.000000] nvram: Active bank is: 1
[    0.000000] nvram: OF partition at 0x410
[    0.000000] nvram: XP partition at 0x1020
[    0.000000] nvram: NR partition at 0x1120
[    0.000000] Top of RAM: 0x80000000, Total RAM: 0x80000000
[    0.000000] Memory hole size: 0MB
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x000000002fffffff]
[    0.000000]   Normal   empty
[    0.000000]   HighMem  [mem 0x0000000030000000-0x000000007fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000007fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[    0.000000] percpu: Embedded 14 pages/cpu s24608 r8192 d24544 u57344
[    0.000000] pcpu-alloc: s24608 r8192 d24544 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Kernel command line: ro root=/dev/sda5 nr_cpus=1 zswap.max_pool_percent=16 slub_debug=FZP page_poison=1 netconsole=6666@192.168.178.8/eth0,6666@192.168.178.3/70:85:C2:30:EC:01 init=/usr/lib/systemd/systemd 
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 522560
[    0.000000] mem auto-init: stack:all(pattern), heap alloc:off, heap free:off
[    0.000000] stackdepot: allocating hash table via alloc_large_system_hash
[    0.000000] stackdepot hash table entries: 1048576 (order: 10, 4194304 bytes, linear)
[    0.000000] Kernel virtual memory layout:
[    0.000000]   * 0xf6000000..0xfec00000  : kasan shadow mem
[    0.000000]   * 0xf5bbf000..0xf5fff000  : fixmap
[    0.000000]   * 0xf5400000..0xf5800000  : highmem PTEs
[    0.000000]   * 0xf5115000..0xf5400000  : early ioremap
[    0.000000]   * 0xf1000000..0xf5110000  : vmalloc & ioremap
[    0.000000]   * 0xb0000000..0xc0000000  : modules
[    0.000000] Memory: 1946640K/2097152K available (16020K kernel code, 1964K rwdata, 4460K rodata, 1344K init, 402K bss, 150512K reserved, 0K cma-reserved, 1212416K highmem)
[    0.000000] **********************************************************
[    0.000000] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
[    0.000000] **                                                      **
[    0.000000] ** This system shows unhashed kernel memory addresses   **
[    0.000000] ** via the console, logs, and other interfaces. This    **
[    0.000000] ** might reduce the security of your system.            **
[    0.000000] **                                                      **
[    0.000000] ** If you see this message and you are not debugging    **
[    0.000000] ** the kernel, report this immediately to your system   **
[    0.000000] ** administrator!                                       **
[    0.000000] **                                                      **
[    0.000000] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
[    0.000000] **********************************************************
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS: 512, nr_irqs: 512, preallocated irqs: 16
[    0.000000] mpic: Resetting
[    0.000000] mpic: Setting up MPIC " MPIC 1   " version 1.2 at 80040000, max 1 CPUs
[    0.000000] mpic: ISU size: 64, shift: 6, mask: 3f
[    0.000000] mpic: Initializing for 64 sources
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] time_init: decrementer frequency = 41.658676 MHz
[    0.000000] time_init: processor frequency   = 1416.666661 MHz
[    0.000008] clocksource: timebase: mask: 0xffffffffffffffff max_cycles: 0x99b9699db, max_idle_ns: 440795204297 ns
[    0.000563] clocksource: timebase mult[18012db2] shift[24] registered
[    0.001064] clockevent: decrementer mult[aaa249b] shift[32] cpu[0]
[    0.003737] Console: colour dummy device 80x25
[    0.004209] printk: console [tty0] enabled
[    0.004724] printk: bootconsole [udbg0] disabled
[    0.005912] pid_max: default: 32768 minimum: 301
[    0.011691] LSM: initializing lsm=capability,yama
[    0.011784] Yama: becoming mindful.
[    0.013668] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.013858] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.029185] PowerMac SMP probe found 2 cpus
[    0.029975] KeyWest i2c @0xf8001003 irq 42 /uni-n@f8000000/i2c@f8001000
[    0.030139]  channel 0 bus <multibus>
[    0.030252]  channel 1 bus <multibus>
[    0.030551] KeyWest i2c @0x80018000 irq 26 /pci@f2000000/mac-io@17/i2c@18000
[    0.030703]  channel 0 bus <multibus>
[    0.030839] PMU i2c /pci@f2000000/mac-io@17/via-pmu@16000/pmu-i2c
[    0.030980]  channel 1 bus <multibus>
[    0.031088]  channel 2 bus <multibus>
[    0.031159] pmf: no parser for command 17 !
[    0.031319] Processor timebase sync using GPIO 0x73
[    0.031355] mpic: requesting IPIs...
[    0.032105] CPU0: L2CR is 80000000
[    0.032142] CPU0: L3CR is 9c030000
[    0.038315] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[    0.039615] MPC7450 family performance monitor hardware support registered
[    0.040547] rcu: Hierarchical SRCU implementation.
[    0.040595] rcu: 	Max phase no-delay instances is 1000.
[    0.042888] smp: Bringing up secondary CPUs ...
[    0.042975] smp: Brought up 1 node, 1 CPU
[    0.047984] devtmpfs: initialized
[    0.051344] Duplicate name in PowerPC,G4@0, renamed to "l2-cache#1"
[    0.052055] Duplicate name in l2-cache#1, renamed to "l2-cache#1"
[    0.054383] Duplicate name in PowerPC,G4@1, renamed to "l2-cache#1"
[    0.054916] Duplicate name in l2-cache#1, renamed to "l2-cache#1"
[    0.080628] Duplicate name in gpio@50, renamed to "gpio5@6f#1"
[    0.081029] Duplicate name in gpio@50, renamed to "gpio6@70#1"
[    0.082046] Duplicate name in gpio@50, renamed to "gpio11@75#1"
[    0.082466] Duplicate name in gpio@50, renamed to "extint-gpio15@67#1"
[    0.120485] Found UniNorth PCI host bridge at 0x00000000f0000000. Firmware bus number: 0->0
[    0.120594] PCI host bridge /pci@f0000000  ranges:
[    0.120692]  MEM 0x00000000f1000000..0x00000000f1ffffff -> 0x00000000f1000000 
[    0.120769]   IO 0x00000000f0000000..0x00000000f07fffff -> 0x0000000000000000
[    0.140115]  MEM 0x0000000090000000..0x00000000afffffff -> 0x0000000090000000 
[    0.140429] Found UniNorth PCI host bridge at 0x00000000f2000000. Firmware bus number: 0->0
[    0.140491] PCI host bridge /pci@f2000000 (primary) ranges:
[    0.140585]  MEM 0x00000000f3000000..0x00000000f3ffffff -> 0x00000000f3000000 
[    0.140662]   IO 0x00000000f2000000..0x00000000f27fffff -> 0x0000000000000000
[    0.160050]  MEM 0x0000000080000000..0x000000008fffffff -> 0x0000000080000000 
[    0.160457] Found UniNorth PCI host bridge at 0x00000000f4000000. Firmware bus number: 0->0
[    0.160519] PCI host bridge /pci@f4000000  ranges:
[    0.160612]  MEM 0x00000000f5000000..0x00000000f5ffffff -> 0x00000000f5000000 
[    0.160675]   IO 0x00000000f4000000..0x00000000f47fffff -> 0x0000000000000000
[    0.180316] Found NEC PD720100A USB2 chip with disabled EHCI, fixing up...
[    0.182323] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.182553] futex hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.184979] prandom: seed boundary self test passed
[    0.192779] prandom: 100 self tests passed
[    0.200394] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.230124] PCI: Probing PCI hardware
[    0.232744] PCI host bridge to bus 0000:00
[    0.232824] pci_bus 0000:00: root bus resource [io  0xff780000-0xfff7ffff] (bus address [0x0000-0x7fffff])
[    0.232906] pci_bus 0000:00: root bus resource [mem 0xf1000000-0xf1ffffff]
[    0.232969] pci_bus 0000:00: root bus resource [mem 0x90000000-0xafffffff]
[    0.233037] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.233088] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to ff
[    0.234781] pci 0000:00:0b.0: [106b:0034] type 00 class 0x060000
[    0.237043] pci 0000:00:10.0: [1002:4150] type 00 class 0x030000
[    0.237132] pci 0000:00:10.0: reg 0x10: [mem 0xa0000000-0xafffffff pref]
[    0.237233] pci 0000:00:10.0: reg 0x14: [io  0xff780400-0xff7804ff]
[    0.237296] pci 0000:00:10.0: reg 0x18: [mem 0x90000000-0x9000ffff]
[    0.237380] pci 0000:00:10.0: reg 0x30: [mem 0x90020000-0x9003ffff pref]
[    0.237506] pci 0000:00:10.0: supports D1 D2
[    0.241372] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.243920] OF: /pci@f2000000/mac-io@17/gpio@50/gpio5@6f: could not find phandle 1751474532
[    0.244167] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio15@67: could not find phandle 1751474532
[    0.244422] OF: /pci@f2000000/mac-io@17/gpio@50/gpio6@70: could not find phandle 1634562093
[    0.244595] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio16@68: could not find phandle 1936745825
[    0.244907] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio14@66: could not find phandle 1818848869
[    0.245106] OF: /pci@f2000000/mac-io@17/gpio@50/gpio12@76: could not find phandle 1835103092
[    0.245266] OF: /pci@f2000000/mac-io@17/gpio@50/gpio11@75: could not find phandle 1635083369
[    0.245415] OF: /pci@f2000000/mac-io@17/gpio@50/gpio5@6f: could not find phandle 1751474532
[    0.245565] OF: /pci@f2000000/mac-io@17/gpio@50/gpio6@70: could not find phandle 1634562093
[    0.245714] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio4@5c: could not find phandle 1818848869
[    0.245907] OF: /pci@f2000000/mac-io@17/gpio@50/gpio11@75: could not find phandle 1635083369
[    0.246058] OF: /pci@f2000000/mac-io@17/gpio@50/extint-gpio15@67: could not find phandle 1751474532
[    0.249689] pci_bus 0001:00: Fixed dependency cycle(s) with /pci@f2000000/mac-io@17/interrupt-controller@40000
[    0.249971] PCI host bridge to bus 0001:00
[    0.250024] pci_bus 0001:00: root bus resource [io  0x0000-0x7fffff]
[    0.250087] pci_bus 0001:00: root bus resource [mem 0xf3000000-0xf3ffffff]
[    0.250149] pci_bus 0001:00: root bus resource [mem 0x80000000-0x8fffffff]
[    0.250214] pci_bus 0001:00: root bus resource [bus 00-ff]
[    0.250264] pci_bus 0001:00: busn_res: [bus 00-ff] end is updated to ff
[    0.251928] pci 0001:00:0b.0: [106b:0035] type 00 class 0x060000
[    0.254776] pci 0001:00:12.0: [1033:0035] type 00 class 0x0c0310
[    0.254863] pci 0001:00:12.0: reg 0x10: [mem 0x8008c000-0x8008cfff]
[    0.255021] pci 0001:00:12.0: supports D1 D2
[    0.255063] pci 0001:00:12.0: PME# supported from D0 D1 D2 D3hot
[    0.257262] pci 0001:00:12.1: [1033:0035] type 00 class 0x0c0310
[    0.257345] pci 0001:00:12.1: reg 0x10: [mem 0x8008b000-0x8008bfff]
[    0.257502] pci 0001:00:12.1: supports D1 D2
[    0.257578] pci 0001:00:12.1: PME# supported from D0 D1 D2 D3hot
[    0.259610] pci 0001:00:12.2: [1033:00e0] type 00 class 0x0c0320
[    0.259693] pci 0001:00:12.2: reg 0x10: [mem 0x80081000-0x800810ff]
[    0.259849] pci 0001:00:12.2: supports D1 D2
[    0.259890] pci 0001:00:12.2: PME# supported from D0 D1 D2 D3hot
[    0.261501] pci 0001:00:13.0: [1095:3112] type 00 class 0x018000
[    0.261580] pci 0001:00:13.0: reg 0x10: [io  0x0460-0x0467]
[    0.261637] pci 0001:00:13.0: reg 0x14: [io  0x0450-0x0453]
[    0.261691] pci 0001:00:13.0: reg 0x18: [io  0x0440-0x0447]
[    0.261745] pci 0001:00:13.0: reg 0x1c: [io  0x0430-0x0433]
[    0.261799] pci 0001:00:13.0: reg 0x20: [io  0x0420-0x042f]
[    0.261853] pci 0001:00:13.0: reg 0x24: [mem 0x80082000-0x800821ff]
[    0.261911] pci 0001:00:13.0: reg 0x30: [mem 0x80100000-0x8017ffff pref]
[    0.262027] pci 0001:00:13.0: supports D1 D2
[    0.264253] pci 0001:00:15.0: [9710:9865] type 00 class 0x070002
[    0.264338] pci 0001:00:15.0: reg 0x10: [io  0x0410-0x0417]
[    0.264396] pci 0001:00:15.0: reg 0x14: [mem 0x8008a000-0x8008afff]
[    0.264502] pci 0001:00:15.0: reg 0x20: [mem 0x80089000-0x80089fff]
[    0.264639] pci 0001:00:15.0: supports D1 D2
[    0.264681] pci 0001:00:15.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.266283] pci 0001:00:15.1: [9710:9865] type 00 class 0x070002
[    0.266364] pci 0001:00:15.1: reg 0x10: [io  0x0400-0x0407]
[    0.266421] pci 0001:00:15.1: reg 0x14: [mem 0x80088000-0x80088fff]
[    0.266493] pci 0001:00:15.1: reg 0x20: [mem 0x80087000-0x80087fff]
[    0.266622] pci 0001:00:15.1: supports D1 D2
[    0.266663] pci 0001:00:15.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.269345] pci 0001:00:15.2: [ffff:9865] type 00 class 0x070103
[    0.269430] pci 0001:00:15.2: reg 0x10: [io  0x0000-0x0007]
[    0.269487] pci 0001:00:15.2: reg 0x14: [io  0x0000-0x0007]
[    0.269542] pci 0001:00:15.2: reg 0x18: [mem 0x00000000-0x00000fff]
[    0.269605] pci 0001:00:15.2: reg 0x20: [mem 0x00000000-0x00000fff]
[    0.269736] pci 0001:00:15.2: supports D1 D2
[    0.269778] pci 0001:00:15.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.271329] pci 0001:00:16.0: [14e4:4320] type 00 class 0x028000
[    0.271410] pci 0001:00:16.0: reg 0x10: [mem 0x8008e000-0x8008ffff]
[    0.271564] pci 0001:00:16.0: supports D1 D2
[    0.271605] pci 0001:00:16.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.273805] pci 0001:00:17.0: [106b:0022] type 00 class 0xff0000
[    0.273888] pci 0001:00:17.0: reg 0x10: [mem 0x80000000-0x8007ffff]
[    0.275717] pci 0001:00:18.0: [106b:0019] type 00 class 0x0c0310
[    0.275800] pci 0001:00:18.0: reg 0x10: [mem 0x80086000-0x80086fff]
[    0.278009] pci 0001:00:19.0: [106b:0019] type 00 class 0x0c0310
[    0.278092] pci 0001:00:19.0: reg 0x10: [mem 0x80085000-0x80085fff]
[    0.280285] pci 0001:00:1b.0: [1033:0035] type 00 class 0x0c0310
[    0.280371] pci 0001:00:1b.0: reg 0x10: [mem 0x80084000-0x80084fff]
[    0.280529] pci 0001:00:1b.0: supports D1 D2
[    0.280572] pci 0001:00:1b.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.282690] pci 0001:00:1b.1: [1033:0035] type 00 class 0x0c0310
[    0.282774] pci 0001:00:1b.1: reg 0x10: [mem 0x80083000-0x80083fff]
[    0.282931] pci 0001:00:1b.1: supports D1 D2
[    0.282973] pci 0001:00:1b.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.284464] pci 0001:00:1b.2: [1033:00e0] type 00 class 0x0c0320
[    0.284543] pci 0001:00:1b.2: reg 0x10: [mem 0x80080000-0x800800ff]
[    0.284730] pci 0001:00:1b.2: supports D1 D2
[    0.284773] pci 0001:00:1b.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.287096] pci_bus 0001:00: busn_res: [bus 00-ff] end is updated to 00
[    0.293314] PCI host bridge to bus 0002:00
[    0.293394] pci_bus 0002:00: root bus resource [io  0x880000-0x107ffff] (bus address [0x0000-0x7fffff])
[    0.293471] pci_bus 0002:00: root bus resource [mem 0xf5000000-0xf5ffffff]
[    0.293537] pci_bus 0002:00: root bus resource [bus 00-ff]
[    0.293587] pci_bus 0002:00: busn_res: [bus 00-ff] end is updated to ff
[    0.295303] pci 0002:00:0b.0: [106b:0036] type 00 class 0x060000
[    0.297592] pci 0002:00:0d.0: [106b:0033] type 00 class 0xff0000
[    0.297676] pci 0002:00:0d.0: reg 0x10: [mem 0xf5004000-0xf5007fff]
[    0.299864] pci 0002:00:0e.0: [106b:0031] type 00 class 0x0c0010
[    0.299947] pci 0002:00:0e.0: reg 0x10: [mem 0xf5000000-0xf5000fff]
[    0.300097] pci 0002:00:0e.0: supports D1 D2
[    0.300139] pci 0002:00:0e.0: PME# supported from D0 D1 D2 D3hot
[    0.302223] pci 0002:00:0f.0: [106b:0032] type 00 class 0x020000
[    0.302305] pci 0002:00:0f.0: reg 0x10: [mem 0xf5200000-0xf53fffff]
[    0.302407] pci 0002:00:0f.0: reg 0x30: [mem 0xf5100000-0xf51fffff pref]
[    0.305896] pci_bus 0002:00: busn_res: [bus 00-ff] end is updated to 00
[    0.307263] PCI 0000:00 Cannot reserve Legacy IO [io  0xff780000-0xff780fff]
[    0.307344] PCI 0001:00 Cannot reserve Legacy IO [io  0x0000-0x0fff]
[    0.307421] pci_bus 0000:00: resource 4 [io  0xff780000-0xfff7ffff]
[    0.307474] pci_bus 0000:00: resource 5 [mem 0xf1000000-0xf1ffffff]
[    0.307522] pci_bus 0000:00: resource 6 [mem 0x90000000-0xafffffff]
[    0.307637] pci 0001:00:15.2: BAR 2: assigned [mem 0xf3000000-0xf3000fff]
[    0.307701] pci 0001:00:15.2: BAR 4: assigned [mem 0xf3001000-0xf3001fff]
[    0.307761] pci 0001:00:15.2: BAR 0: assigned [io  0x1000-0x1007]
[    0.307819] pci 0001:00:15.2: BAR 1: assigned [io  0x1008-0x100f]
[    0.307895] pci_bus 0001:00: resource 4 [io  0x0000-0x7fffff]
[    0.307943] pci_bus 0001:00: resource 5 [mem 0xf3000000-0xf3ffffff]
[    0.307991] pci_bus 0001:00: resource 6 [mem 0x80000000-0x8fffffff]
[    0.308046] pci_bus 0002:00: resource 4 [io  0x880000-0x107ffff]
[    0.308094] pci_bus 0002:00: resource 5 [mem 0xf5000000-0xf5ffffff]
[    0.385660] raid6: altivecx8 gen()   550 MB/s
[    0.442537] raid6: altivecx4 gen()   537 MB/s
[    0.499393] raid6: altivecx2 gen()   476 MB/s
[    0.556288] raid6: altivecx1 gen()   388 MB/s
[    0.613182] raid6: int32x8  gen()   139 MB/s
[    0.670147] raid6: int32x4  gen()   134 MB/s
[    0.726899] raid6: int32x2  gen()   118 MB/s
[    0.783740] raid6: int32x1  gen()    94 MB/s
[    0.783777] raid6: using algorithm altivecx8 gen() 550 MB/s
[    0.783815] raid6: using intx1 recovery algorithm
[    0.795889] SCSI subsystem initialized
[    0.799583] libata version 3.00 loaded.
[    0.801615] usbcore: registered new interface driver usbfs
[    0.802259] usbcore: registered new interface driver hub
[    0.803329] usbcore: registered new device driver usb
[    0.820474] pci 0000:00:10.0: vgaarb: setting as boot VGA device
[    0.820554] pci 0000:00:10.0: vgaarb: bridge control possible
[    0.820596] pci 0000:00:10.0: vgaarb: VGA device added: decodes=io+mem,owns=mem,locks=none
[    0.820747] vgaarb: loaded
[    0.822262] clocksource: Switched to clocksource timebase
[    0.951397] NET: Registered PF_INET protocol family
[    0.954313] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.963957] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 10240 bytes, linear)
[    0.968369] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.970584] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.979737] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear)
[    0.982007] TCP: Hash tables configured (established 8192 bind 8192)
[    0.985032] UDP hash table entries: 512 (order: 2, 24576 bytes, linear)
[    0.985878] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes, linear)
[    0.987844] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.989418] pci 0001:00:12.0: enabling device (0000 -> 0002)
[    0.989615] pci 0001:00:12.1: enabling device (0000 -> 0002)
[    0.989749] pci 0001:00:12.2: enabling device (0004 -> 0006)
[    0.990096] Apple USB OHCI 0001:00:18.0 disabled by firmware
[    0.990143] pci 0001:00:18.0: Can't enable PCI device, BIOS handoff failed.
[    0.990212] Apple USB OHCI 0001:00:19.0 disabled by firmware
[    0.990251] pci 0001:00:19.0: Can't enable PCI device, BIOS handoff failed.
[    0.990328] pci 0001:00:1b.0: enabling device (0000 -> 0002)
[    0.990456] pci 0001:00:1b.1: enabling device (0000 -> 0002)
[    0.990578] pci 0001:00:1b.2: enabling device (0004 -> 0006)
[    0.990770] pci 0002:00:0f.0: CLS mismatch (32 != 1020), using 32 bytes
[    0.992923] Thermal assist unit not available
[    1.011479] Initialise system trusted keyrings
[    1.012804] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[    1.040347] fuse: init (API version 7.38)
[    1.043092] 9p: Installing v9fs 9p2000 file system support
[    1.044807] NET: Registered PF_ALG protocol family
[    1.045145] xor: measuring software checksum speed
[    1.122882]    8regs           :   126 MB/sec
[    1.201244]    8regs_prefetch  :   125 MB/sec
[    1.280278]    32regs          :   124 MB/sec
[    1.360192]    32regs_prefetch :   123 MB/sec
[    1.380101]    altivec         :   495 MB/sec
[    1.380139] xor: using function: altivec (495 MB/sec)
[    1.380297] Key type asymmetric registered
[    1.380342] Asymmetric key parser 'x509' registered
[    1.409659] bounce: pool size: 64 pages
[    1.410984] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.411049] io scheduler kyber registered
[    1.411647] io scheduler bfq registered
[    1.442213] MacIO PCI driver attached to Keylargo chipset
[    1.466827] 0.00013020:ch-a: ttyS0 at MMIO 0x80013020 (irq = 22, base_baud = 230400) is a Z85c30 ESCC - Serial port
[    1.475303] 0.00013000:ch-b: ttyS1 at MMIO 0x80013000 (irq = 23, base_baud = 230400) is a Z85c30 ESCC - Serial port
[    1.496206] sata_sil 0001:00:13.0: version 2.4
[    1.497033] sata_sil 0001:00:13.0: enabling device (0004 -> 0007)
[    1.510223] scsi host0: sata_sil
[    1.516842] scsi host1: sata_sil
[    1.519592] ata1: SATA max UDMA/100 mmio m512@0x80082000 tf 0x80082080 irq 53
[    1.519658] ata2: SATA max UDMA/100 mmio m512@0x80082000 tf 0x800820c0 irq 53
[    1.522304] pata-pci-macio 0002:00:0d.0: enabling device (0004 -> 0006)
[    1.538977] pata-pci-macio 0002:00:0d.0: Activating pata-macio chipset UniNorth ATA-6, Apple bus ID 3
[    1.548943] scsi host2: pata_macio
[    1.552108] ata3: PATA max UDMA/100 irq 39
[    1.832321] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[    1.835293] ata1.00: ATA-9: SanDisk SSD PLUS 240GB, UF4500RL, max UDMA/133
[    1.835354] ata1.00: 468877312 sectors, multi 1: LBA48 NCQ (depth 0/32)
[    1.836776] ata1.00: Features: Dev-Sleep
[    1.860500] ata1.00: configured for UDMA/100
[    1.861990] scsi 0:0:0:0: Direct-Access     ATA      SanDisk SSD PLUS 00RL PQ: 0 ANSI: 5
[    1.874575] sd 0:0:0:0: [sda] 468877312 512-byte logical blocks: (240 GB/224 GiB)
[    1.874911] sd 0:0:0:0: [sda] Write Protect is off
[    1.874985] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.875301] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.875879] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[    1.886155]  sda: [mac] sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8
[    1.900523] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.302294] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[    2.304819] ata2.00: ATA-9: WDC WD5000LPLX-60ZNTT1, 02.01A02, max UDMA/133
[    2.304878] ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[    2.307533] ata2.00: configured for UDMA/100
[    2.308553] scsi 1:0:0:0: Direct-Access     ATA      WDC WD5000LPLX-6 1A02 PQ: 0 ANSI: 5
[    2.316273] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[    2.316379] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[    2.316589] sd 1:0:0:0: [sdb] Write Protect is off
[    2.316661] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    2.317065] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.317495] sd 1:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes
[    2.595625] pata-macio 0.0001f000:ata-4: Activating pata-macio chipset KeyLargo ATA-4, Apple bus ID 2
[    2.605904] scsi host3: pata_macio
[    2.608659] ata4: PATA max UDMA/66 irq 19
[    2.768334] ata4.00: CFA: DeLOCK 54143 512MB, 100511E, max UDMA/66
[    2.768408] ata4.00: 1009008 sectors, multi 1: LBA 
[    3.022113]  sdb: [mac] sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8
[    3.035984] sd 1:0:0:0: [sdb] Attached SCSI disk
[    3.038715] scsi 3:0:0:0: Direct-Access     ATA      DeLOCK 54143 512 11E  PQ: 0 ANSI: 5
[    3.047209] sd 3:0:0:0: [sdc] 1009008 512-byte logical blocks: (517 MB/493 MiB)
[    3.047468] sd 3:0:0:0: [sdc] Write Protect is off
[    3.047540] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[    3.047845] sd 3:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    3.048357] sd 3:0:0:0: [sdc] Preferred minimum I/O size 512 bytes
[    3.060319]  sdc: [mac] sdc1 sdc2 sdc3 sdc4 sdc5 sdc6
[    3.073143] sd 3:0:0:0: [sdc] Attached SCSI disk
[    3.635624] pata-macio 0.00020000:ata-3: Activating pata-macio chipset KeyLargo ATA-3, Apple bus ID 0
[    3.644975] scsi host4: pata_macio
[    3.647907] ata5: PATA max MWDMA2 irq 20
[    3.649925] tun: Universal TUN/TAP device driver, 1.6
[    3.652765] sungem.c:v1.0 David S. Miller <davem@redhat.com>
[    3.665431] gem 0002:00:0f.0 eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0a:95:9c:76:3a
[    3.670781] ehci-pci 0001:00:12.2: EHCI Host Controller
[    3.671071] ehci-pci 0001:00:12.2: new USB bus registered, assigned bus number 1
[    3.672645] ehci-pci 0001:00:12.2: irq 52, io mem 0x80081000
[    3.677570] rtc-generic rtc-generic: registered as rtc0
[    3.680663] PowerMac i2c bus pmu 2 registered
[    3.682644] PowerMac i2c bus pmu 1 registered
[    3.685664] ehci-pci 0001:00:12.2: USB 2.0 started, EHCI 1.00
[    3.687453] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[    3.687527] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.687580] usb usb1: Product: EHCI Host Controller
[    3.687620] usb usb1: Manufacturer: Linux 6.5.0-rc6-PMacG4-dirty ehci_hcd
[    3.687664] usb usb1: SerialNumber: 0001:00:12.2
[    3.692120] PowerMac i2c bus mac-io 0 registered
[    3.693703] i2c i2c-2: No i2c address for /pci@f2000000/mac-io@17/i2c@18000/i2c-modem
[    3.696650] hub 1-0:1.0: USB hub found
[    3.696939] hub 1-0:1.0: 5 ports detected
[    3.702112] PowerMac i2c bus uni-n 1 registered
[    3.702197] i2c i2c-3: i2c-powermac: modalias failure on /uni-n@f8000000/i2c@f8001000/cereal@1c0
[    3.704197] PowerMac i2c bus uni-n 0 registered
[    3.713018] ehci-pci 0001:00:1b.2: EHCI Host Controller
[    3.713187] ehci-pci 0001:00:1b.2: new USB bus registered, assigned bus number 2
[    3.714224] ehci-pci 0001:00:1b.2: irq 63, io mem 0x80080000
[    3.717763] hid: raw HID events driver (C) Jiri Kosina
[    3.721004] usbcore: registered new interface driver usbhid
[    3.721059] usbhid: USB HID core driver
[    3.725857] ehci-pci 0001:00:1b.2: USB 2.0 started, EHCI 1.00
[    3.727146] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[    3.727218] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.727271] usb usb2: Product: EHCI Host Controller
[    3.727311] usb usb2: Manufacturer: Linux 6.5.0-rc6-PMacG4-dirty ehci_hcd
[    3.727356] usb usb2: SerialNumber: 0001:00:1b.2
[    3.733507] NET: Registered PF_INET6 protocol family
[    3.735493] hub 2-0:1.0: USB hub found
[    3.735858] hub 2-0:1.0: 5 ports detected
[    3.755095] Segment Routing with IPv6
[    3.756381] In-situ OAM (IOAM) with IPv6
[    3.756925] NET: Registered PF_PACKET protocol family
[    3.757013] NET: Registered PF_KEY protocol family
[    3.759085] 9pnet: Installing 9P2000 support
[    3.762417] drmem: No dynamic reconfiguration memory found
[    3.805114] ata5.00: ATAPI: _NEC DVD_RW ND-3520A, 1.04, max UDMA/33
[    3.816211] scsi 4:0:0:0: CD-ROM            _NEC     DVD_RW ND-3520A  1.04 PQ: 0 ANSI: 5
[    3.870920] sr 4:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[    3.871037] cdrom: Uniform CD-ROM driver Revision: 3.20
[    3.894561] sr 4:0:0:0: Attached scsi CD-ROM sr0
[    3.949149] Loading compiled-in X.509 certificates
[    3.959157] usb 1-5: new high-speed USB device number 2 using ehci-pci
[    4.088156] zswap: loaded using pool zstd/z3fold
[    4.108675] usb 1-5: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=32.98
[    4.108773] usb 1-5: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    4.108821] usb 1-5: Product: USB2.0 Hub
[    4.113724] hub 1-5:1.0: USB hub found
[    4.114813] hub 1-5:1.0: 4 ports detected
[    4.327780] debug_vm_pgtable: [debug_vm_pgtable         ]: Validating architecture page table helpers
[    4.482294] usb 1-5.1: new low-speed USB device number 3 using ehci-pci
[    4.543295] Btrfs loaded, zoned=no, fsverity=no
[    4.610051] usb 1-5.1: New USB device found, idVendor=04d9, idProduct=0006, bcdDevice= 1.40
[    4.610172] usb 1-5.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.610225] usb 1-5.1: Product: RPI Wired Keyboard 5
[    4.610266] usb 1-5.1: Manufacturer:  
[    4.655163] input:   RPI Wired Keyboard 5 as /devices/pci0001:00/0001:00:12.2/usb1/1-5/1-5.1/1-5.1:1.0/0003:04D9:0006.0001/input/input0
[    4.729865] hid-generic 0003:04D9:0006.0001: input,hidraw0: USB HID v1.11 Keyboard [  RPI Wired Keyboard 5] on usb-0001:00:12.2-5.1/input0
[    4.767714] input:   RPI Wired Keyboard 5 as /devices/pci0001:00/0001:00:12.2/usb1/1-5/1-5.1/1-5.1:1.1/0003:04D9:0006.0002/input/input1
[    4.826227] hid-generic 0003:04D9:0006.0002: input,hidraw1: USB HID v1.11 Device [  RPI Wired Keyboard 5] on usb-0001:00:12.2-5.1/input1
[    4.912305] usb 1-5.4: new low-speed USB device number 4 using ehci-pci
[    5.013309] usb 1-5.4: New USB device found, idVendor=275d, idProduct=0ba6, bcdDevice= 1.00
[    5.013386] usb 1-5.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    5.013438] usb 1-5.4: Product: USB OPTICAL MOUSE 
[    5.042405] input: USB OPTICAL MOUSE  as /devices/pci0001:00/0001:00:12.2/usb1/1-5/1-5.4/1-5.4:1.0/0003:275D:0BA6.0003/input/input2
[   20.647470] EXT4-fs (sda5): mounted filesystem 28419c7c-4bc4-4922-bdc8-6d8515c62385 ro with ordered data mode. Quota mode: disabled.
[   20.648010] VFS: Mounted root (ext4 filesystem) readonly on device 8:5.
[   20.654315] devtmpfs: mounted
[   20.658822] Freeing unused kernel image (initmem) memory: 1344K
[   20.690393] Checked W+X mappings: passed, no W+X pages found
[   20.690588] rodata_test: all tests were successful
[   20.690728] kallsyms_selftest: start
[   20.718972] Run /usr/lib/systemd/systemd as init process
[   20.719336]   with arguments:
[   20.719538]     /usr/lib/systemd/systemd
[   20.719641]   with environment:
[   20.719737]     HOME=/
[   20.719809]     TERM=linux
[   21.993799] systemd[1]: systemd 253 running in system mode (+PAM -AUDIT -SELINUX -APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID -CURL +ELFUTILS -FIDO2 +IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 +LZ4 -XZ -ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP -SYSVINIT default-hierarchy=unified)
[   21.994423] systemd[1]: Detected architecture ppc.
[   22.040493] systemd[1]: Hostname set to <T600>.
[   22.332001] memfd_create() without MFD_EXEC nor MFD_NOEXEC_SEAL, pid=1 'systemd'
[   27.511794] systemd[1]: Queued start job for default target graphical.target.
[   27.607262] systemd[1]: Created slice system-getty.slice.
[   27.640112] systemd[1]: Created slice system-modprobe.slice.
[   27.667667] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[   27.695397] systemd[1]: Created slice system-vncserver.slice.
[   27.725827] systemd[1]: Created slice user.slice.
[   27.734948] systemd[1]: Started systemd-ask-password-console.path.
[   27.746402] systemd[1]: Started systemd-ask-password-wall.path.
[   27.765904] systemd[1]: Set up automount proc-sys-fs-binfmt_misc.automount.
[   27.773002] systemd[1]: Reached target paths.target.
[   27.774230] systemd[1]: Reached target remote-fs.target.
[   27.776202] systemd[1]: Reached target slices.target.
[   27.822035] systemd[1]: Listening on systemd-coredump.socket.
[   27.842939] systemd[1]: Listening on systemd-journald-dev-log.socket.
[   27.858550] systemd[1]: Listening on systemd-journald.socket.
[   27.878442] systemd[1]: Listening on systemd-udevd-control.socket.
[   27.895933] systemd[1]: Listening on systemd-udevd-kernel.socket.
[   27.909726] systemd[1]: dev-hugepages.mount was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/mm/hugepages).
[   27.986640] systemd[1]: Mounting dev-mqueue.mount...
[   28.129937] systemd[1]: Mounting sys-kernel-debug.mount...
[   28.137561] systemd[1]: sys-kernel-tracing.mount was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/tracing).
[   28.327841] systemd[1]: Starting kmod-static-nodes.service...
[   28.451072] systemd[1]: Starting modprobe@configfs.service...
[   28.574730] systemd[1]: Starting modprobe@dm_mod.service...
[   28.733993] systemd[1]: Starting modprobe@drm.service...
[   28.898118] systemd[1]: Starting modprobe@fuse.service...
[   28.937336] device-mapper: uevent: version 1.0.3
[   28.960144] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[   29.041269] systemd[1]: Starting modprobe@loop.service...
[   29.158584] systemd[1]: Starting systemd-fsck-root.service...
[   29.521197] systemd[1]: Starting systemd-journald.service...
[   29.582003] loop: module loaded
[   29.741440] systemd[1]: Starting systemd-modules-load.service...
[   29.949378] systemd[1]: Starting systemd-udev-trigger.service...
[   30.753210] systemd[1]: Mounted dev-mqueue.mount.
[   30.905235] systemd-journald[99]: Collecting audit messages is disabled.
[   30.998686] systemd[1]: Mounted sys-kernel-debug.mount.
[   31.045911] systemd[1]: Finished kmod-static-nodes.service.
[   31.331356] systemd[1]: modprobe@configfs.service: Deactivated successfully.
[   31.360944] systemd[1]: Finished modprobe@configfs.service.
[   31.620256] systemd[1]: modprobe@dm_mod.service: Deactivated successfully.
[   31.641012] systemd[1]: Finished modprobe@dm_mod.service.
[   31.732438] systemd[1]: modprobe@drm.service: Deactivated successfully.
[   31.749522] systemd[1]: Finished modprobe@drm.service.
[   31.805895] systemd[1]: modprobe@fuse.service: Deactivated successfully.
[   31.856634] systemd[1]: Finished modprobe@fuse.service.
[   31.904118] systemd[1]: modprobe@loop.service: Deactivated successfully.
[   31.927468] systemd[1]: Finished modprobe@loop.service.
[   32.090959] systemd[1]: Finished systemd-fsck-root.service.
[   32.119397] systemd[1]: Finished systemd-modules-load.service.
[   32.566811] systemd[1]: Mounting sys-fs-fuse-connections.mount...
[   32.796752] systemd[1]: Mounting sys-kernel-config.mount...
[   33.291738] systemd[1]: Starting systemd-remount-fs.service...
[   33.322608] systemd[1]: systemd-repart.service was skipped because no trigger condition checks were met.
[   33.472155] systemd[1]: Starting systemd-sysctl.service...
[   33.859341] systemd[1]: Mounted sys-fs-fuse-connections.mount.
[   33.907274] systemd[1]: Mounted sys-kernel-config.mount.
[   34.882688] systemd[1]: Finished systemd-sysctl.service.
[   39.992443] EXT4-fs (sda5): re-mounted 28419c7c-4bc4-4922-bdc8-6d8515c62385 r/w. Quota mode: disabled.
[   40.239173] systemd[1]: Finished systemd-remount-fs.service.
[   40.243951] systemd[1]: systemd-firstboot.service was skipped because of an unmet condition check (ConditionFirstBoot=yes).
[   40.289381] systemd[1]: systemd-hwdb-update.service was skipped because of an unmet condition check (ConditionNeedsUpdate=/etc).
[   40.418494] systemd[1]: Starting systemd-random-seed.service...
[   40.435076] systemd[1]: systemd-sysusers.service was skipped because no trigger condition checks were met.
[   40.628092] systemd[1]: Starting systemd-tmpfiles-setup-dev.service...
[   41.559009] random: crng init done
[   41.652961] systemd[1]: Finished systemd-random-seed.service.
[   41.660267] systemd[1]: first-boot-complete.target was skipped because of an unmet condition check (ConditionFirstBoot=yes).
[   48.015390] systemd[1]: Started systemd-journald.service.
[   48.853077] systemd-journald[99]: Received client request to flush runtime journal.
[   49.322582] systemd-journald[99]: /var/log/journal/71303955349d475c9d69360df5e2c5b5/system.journal: Monotonic clock jumped backwards relative to last journal entry, rotating.
[   49.322884] systemd-journald[99]: Rotating system journal.
[   80.725161] gem 0002:00:0f.0 enP2p0s15: renamed from eth0 (while UP)
[   86.270902] kallsyms_selftest:  ---------------------------------------------------------
[   86.271166] kallsyms_selftest: | nr_symbols | compressed size | original size | ratio(%) |
[   86.271271] kallsyms_selftest: |---------------------------------------------------------|
[   86.271415] kallsyms_selftest: |      33826 |        363977   |       629231  |  57.84   |
[   86.271520] kallsyms_selftest:  ---------------------------------------------------------
[   88.357357] BTRFS: device label tmp devid 1 transid 61 /dev/sda6 scanned by (udev-worker) (138)
[   88.396959] BTRFS: device label g4_musl devid 1 transid 64495 /dev/sda4 scanned by (udev-worker) (133)
[   91.266436] Adding 8388604k swap on /dev/sdb6.  Priority:-2 extents:1 across:8388604k FS
[   95.667289] kallsyms_selftest: kallsyms_lookup_name() looked up 33826 symbols
[   95.667559] kallsyms_selftest: The time spent on each symbol is (ns): min=5737, max=1420401, avg=102646
[   95.754116] kallsyms_selftest: kallsyms_on_each_symbol() traverse all: 86416365 ns
[   95.754598] kallsyms_selftest: kallsyms_on_each_match_symbol() traverse all: 85865 ns
[   95.754708] kallsyms_selftest: finish
[   99.662856] ohci-pci 0001:00:12.0: OHCI PCI host controller
[   99.663236] ohci-pci 0001:00:12.0: new USB bus registered, assigned bus number 3
[   99.664028] ohci-pci 0001:00:12.0: irq 52, io mem 0x8008c000
[  100.595894] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.05
[  100.596166] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[  100.596311] usb usb3: Product: OHCI PCI host controller
[  100.596439] usb usb3: Manufacturer: Linux 6.5.0-rc6-PMacG4-dirty ohci_hcd
[  100.596568] usb usb3: SerialNumber: 0001:00:12.0
[  100.850368] hub 3-0:1.0: USB hub found
[  100.919459] hub 3-0:1.0: 3 ports detected
[  101.080125] ohci-pci 0001:00:12.1: OHCI PCI host controller
[  101.080461] ohci-pci 0001:00:12.1: new USB bus registered, assigned bus number 4
[  101.081153] ohci-pci 0001:00:12.1: irq 52, io mem 0x8008b000
[  101.289084] EXT4-fs (sdc5): mounting ext2 file system using the ext4 subsystem
[  101.350180] EXT4-fs (sdc5): mounted filesystem e4e8af9e-0f0d-44f9-b983-71bf61d782de r/w without journal. Quota mode: disabled.
[  101.350617] ext2 filesystem being mounted at /boot supports timestamps until 2038-01-19 (0x7fffffff)
[  101.457174] BTRFS info (device sda6): using xxhash64 (xxhash64-generic) checksum algorithm
[  101.457493] BTRFS info (device sda6): use lzo compression, level 0
[  101.457635] BTRFS info (device sda6): using free space tree
[  101.596333] BTRFS info (device sda6): enabling ssd optimizations
[  101.660079] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.05
[  101.660364] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[  101.660508] usb usb4: Product: OHCI PCI host controller
[  101.660633] usb usb4: Manufacturer: Linux 6.5.0-rc6-PMacG4-dirty ohci_hcd
[  101.660761] usb usb4: SerialNumber: 0001:00:12.1
[  101.744088] hub 4-0:1.0: USB hub found
[  101.802889] hub 4-0:1.0: 2 ports detected
[  101.901616] Apple USB OHCI 0001:00:18.0 disabled by firmware
[  101.901975] Apple USB OHCI 0001:00:19.0 disabled by firmware
[  101.956705] ohci-pci 0001:00:1b.0: OHCI PCI host controller
[  101.957067] ohci-pci 0001:00:1b.0: new USB bus registered, assigned bus number 5
[  101.957839] ohci-pci 0001:00:1b.0: irq 63, io mem 0x80084000
[  102.249688] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.05
[  102.249951] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[  102.250094] usb usb5: Product: OHCI PCI host controller
[  102.250220] usb usb5: Manufacturer: Linux 6.5.0-rc6-PMacG4-dirty ohci_hcd
[  102.250349] usb usb5: SerialNumber: 0001:00:1b.0
[  102.301478] hub 5-0:1.0: USB hub found
[  102.308600] hub 5-0:1.0: 3 ports detected
[  102.447077] ohci-pci 0001:00:1b.1: OHCI PCI host controller
[  102.447427] ohci-pci 0001:00:1b.1: new USB bus registered, assigned bus number 6
[  102.448142] ohci-pci 0001:00:1b.1: irq 63, io mem 0x80083000
[  102.603645] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.05
[  102.603918] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[  102.604065] usb usb6: Product: OHCI PCI host controller
[  102.604308] usb usb6: Manufacturer: Linux 6.5.0-rc6-PMacG4-dirty ohci_hcd
[  102.604451] usb usb6: SerialNumber: 0001:00:1b.1
[  102.667009] hub 6-0:1.0: USB hub found
[  102.672376] hub 6-0:1.0: 2 ports detected
[  105.324697] b43-pci-bridge 0001:00:16.0: enabling device (0004 -> 0006)
[  105.325067] ssb: Found chip with id 0x4306, rev 0x02 and package 0x00
[  105.387827] b43-pci-bridge 0001:00:16.0: Sonics Silicon Backplane found on PCI device 0001:00:16.0
[  112.439904] firewire_ohci 0002:00:0e.0: enabling device (0000 -> 0002)
[  112.599924] firewire_ohci 0002:00:0e.0: added OHCI v1.10 device as card 0, 8 IR + 8 IT contexts, quirks 0x0
[  113.110552] firewire_core 0002:00:0e.0: created device fw0: GUID 000a95fffe9c763a, S800
[  114.925746] ADM1030 fan controller [@2c]
[  115.028355] DS1775 digital thermometer [@49]
[  115.028636] Temp: 49.3 C
[  115.028656]   Hyst: 70.0 C
[  115.028776]   OS: 75.0 C
[  115.029161] 
[  117.240188] [drm] radeon kernel modesetting enabled.
[  117.240813] radeon 0000:00:10.0: vgaarb: deactivate vga console
[  117.573136] radeon 0000:00:10.0: enabling device (0006 -> 0007)
[  117.976745] [drm] initializing kernel modesetting (RV350 0x1002:0x4150 0x1002:0x0002 0x00).
[  117.977024] [drm] Forcing AGP to PCI mode
[  117.978547] radeon 0000:00:10.0: Invalid PCI ROM header signature: expecting 0xaa55, got 0x0000
[  120.579166] [drm] Generation 2 PCI interface, using max accessible memory
[  120.579447] radeon 0000:00:10.0: VRAM: 256M 0x00000000A0000000 - 0x00000000AFFFFFFF (256M used)
[  120.579610] radeon 0000:00:10.0: GTT: 512M 0x0000000080000000 - 0x000000009FFFFFFF
[  120.579927] [drm] Detected VRAM RAM=256M, BAR=256M
[  120.580059] [drm] RAM width 128bits DDR
[  120.616411] [drm] radeon: 256M of VRAM memory ready
[  120.616666] [drm] radeon: 512M of GTT memory ready.
[  120.617171] [drm] GART: num cpu pages 131072, num gpu pages 131072
[  121.305922] [drm] radeon: 1 quad pipes, 1 Z pipes initialized
[  121.306143] [drm] PCI GART of 512M enabled (table at 0x000000000A480000).
[  121.306523] radeon 0000:00:10.0: WB enabled
[  121.306671] radeon 0000:00:10.0: fence driver on ring 0 use gpu addr 0x0000000080000000
[  121.359262] [drm] radeon: irq initialized.
[  121.359622] [drm] Loading R300 Microcode
[  122.246715] [drm] radeon: ring at 0x0000000080001000
[  122.247011] [drm] ring test succeeded in 0 usecs
[  122.618767] [drm] ib test succeeded in 0 usecs
[  122.965416] [drm] Radeon Display Connectors
[  122.965687] [drm] Connector 0:
[  122.965777] [drm]   DVI-I-1
[  122.965853] [drm]   HPD2
[  122.965928] [drm]   DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[  122.966021] [drm]   Encoders:
[  122.966096] [drm]     CRT1: INTERNAL_DAC1
[  122.966178] [drm]     DFP2: INTERNAL_DVO1
[  122.966259] [drm] Connector 1:
[  122.966333] [drm]   DVI-I-2
[  122.966406] [drm]   HPD1
[  122.966491] [drm]   DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[  122.966585] [drm]   Encoders:
[  122.966662] [drm]     CRT2: INTERNAL_DAC2
[  122.966744] [drm]     DFP1: INTERNAL_TMDS1
[  123.159225] CPU-temp: 49.3 C
[  123.159280] , Case: 34.0 C
[  123.159472] ,  Fan: 0 (tuned -11)
[  123.193147] [drm] Initialized radeon 2.50.0 20080528 for 0000:00:10.0 on minor 0
[  125.770971] [drm] fb mappable at 0xA0040000
[  125.771261] [drm] vram apper at 0xA0000000
[  125.771384] [drm] size 8294400
[  125.771495] [drm] fb depth is 24
[  125.771606] [drm]    pitch is 7680
[  132.533300] Console: switching to colour frame buffer device 240x67
[  132.985943] systemd-journald[99]: /var/log/journal/71303955349d475c9d69360df5e2c5b5/user-1000.journal: Monotonic clock jumped backwards relative to last journal entry, rotating.
[  137.079409] radeon 0000:00:10.0: [drm] fb0: radeondrmfb frame buffer device
[  146.522348] snd-aoa-fabric-layout: Using direct GPIOs
[  146.720972] snd-aoa-fabric-layout: can use this codec
[  146.853256] snd-aoa-codec-tas: tas found, addr 0x35 on /pci@f2000000/mac-io@17/i2c@18000/deq@6a
[  148.170432] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[  149.206022] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[  149.208722] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[  149.210079] cfg80211: failed to load regulatory.db
[  152.876767] b43legacy-phy0: Broadcom 4306 WLAN found (core revision 4)
[  152.922379] b43legacy-phy0 debug: Found PHY: Analog 1, Type 2, Revision 1
[  152.923462] b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
[  152.952361] b43legacy-phy0 debug: Radio initialized
[  152.954449] b43legacy-phy0: Loading firmware b43legacy/ucode4.fw
[  152.963853] Broadcom 43xx-legacy driver loaded [ Features: PLID ]
[  152.968131] b43legacy-phy0: Loading firmware b43legacy/pcm4.fw
[  152.985949] b43legacy-phy0: Loading firmware b43legacy/b0g0initvals2.fw
[  153.000543] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[  182.396345] EXT4-fs (sdc5): unmounting filesystem e4e8af9e-0f0d-44f9-b983-71bf61d782de.
[  185.345390] systemd-shutdown[1]: Syncing filesystems and block devices.
[  185.581523] systemd-shutdown[1]: Sending SIGTERM to remaining processes...
[  185.730079] systemd-journald[99]: Received SIGTERM from PID 1 (systemd-shutdow).
[  185.933104] systemd-shutdown[1]: Sending SIGKILL to remaining processes...
[  186.060175] systemd-shutdown[1]: Unmounting file systems.
[  186.109987] (sd-remount)[394]: Remounting '/' read-only with options ''.
[  186.178892] EXT4-fs (sda5): re-mounted 28419c7c-4bc4-4922-bdc8-6d8515c62385 ro. Quota mode: disabled.
[  186.483481] systemd-shutdown[1]: All filesystems unmounted.
[  186.516309] systemd-shutdown[1]: Deactivating swaps.
[  186.550171] systemd-shutdown[1]: All swaps deactivated.
[  186.582799] systemd-shutdown[1]: Detaching loop devices.
[  186.689996] systemd-shutdown[1]: All loop devices detached.
[  186.722830] systemd-shutdown[1]: Stopping MD devices.
[  186.757006] systemd-shutdown[1]: All MD devices stopped.
[  186.789638] systemd-shutdown[1]: Detaching DM devices.
[  186.823697] systemd-shutdown[1]: All DM devices detached.
[  186.856452] systemd-shutdown[1]: All filesystems, swaps, loop devices, MD devices and DM devices detached.
[  186.921232] systemd-shutdown[1]: Syncing filesystems and block devices.
[  186.990432] systemd-shutdown[1]: Powering off.
[  187.025066] sd 3:0:0:0: [sdc] Stopping disk
[  187.059567] sd 1:0:0:0: [sdb] Synchronizing SCSI cache
[  187.093859] sd 1:0:0:0: [sdb] Stopping disk
[  187.421241] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[  187.455158] sd 0:0:0:0: [sda] Stopping disk
[  187.500387] reboot: Power down

  reply	other threads:[~2023-08-18 16:24 UTC|newest]

Thread overview: 34+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-08-10 23:48 KASAN debug kernel fails to boot at early stage when CONFIG_SMP=y is set (kernel 6.5-rc5, PowerMac G4 3,6) Erhard Furtner
2023-08-11  6:45 ` Christophe Leroy
2023-08-13 19:38   ` Erhard Furtner
2023-08-14  9:40     ` Christophe Leroy
2023-08-14 17:27       ` Erhard Furtner
2023-08-15 17:21         ` [PATCH] Add pr_info() traces for investigation Christophe Leroy
2023-08-15 17:25         ` KASAN debug kernel fails to boot at early stage when CONFIG_SMP=y is set (kernel 6.5-rc5, PowerMac G4 3,6) Christophe Leroy
2023-08-15 20:01           ` Erhard Furtner
2023-08-16 15:56             ` Christophe Leroy
2023-08-17 18:32               ` Erhard Furtner
2023-08-17 23:13                 ` Michael Ellerman
2023-08-18  9:16                   ` Erhard Furtner
2023-08-18 15:47                     ` Christophe Leroy
2023-08-18 16:23                       ` Erhard Furtner [this message]
2023-08-22  7:31                         ` Christophe Leroy
2023-08-24  0:00                           ` Erhard Furtner
2023-08-24 11:36                             ` Michael Ellerman
2023-08-27 23:17                               ` Erhard Furtner
2023-08-31  5:32                                 ` Christophe Leroy
2023-08-31 22:44                                   ` Erhard Furtner
2023-09-01  7:43                                     ` Christophe Leroy
2023-09-03 21:06                                       ` Erhard Furtner
2023-09-04 14:48                                         ` Christophe Leroy
2023-09-04 14:55                                           ` Christophe Leroy
2023-09-04 21:32                                             ` Erhard Furtner
2023-09-12  0:11                                             ` Erhard Furtner
2023-09-12  7:47                                               ` Christophe Leroy
2023-09-12 15:59                                                 ` Erhard Furtner
2023-09-12 17:39                                                   ` Christophe Leroy
2023-09-12 20:09                                                     ` Erhard Furtner
2023-09-13  5:28                                                       ` Christophe Leroy
2023-09-14  4:54                                                     ` Christophe Leroy
2023-09-14 12:33                                                       ` Erhard Furtner
2024-02-28 23:55                                                       ` Erhard Furtner

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230818182316.79303545@yea \
    --to=erhard_f@mailbox.org \
    --cc=christophe.leroy@csgroup.eu \
    --cc=linuxppc-dev@lists.ozlabs.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).