From: Eliav Farber <farbere@amazon.com>
To: <linux@armlinux.org.uk>, <catalin.marinas@arm.com>,
<will@kernel.org>, <mpe@ellerman.id.au>, <npiggin@gmail.com>,
<christophe.leroy@csgroup.eu>, <naveen@kernel.org>,
<maddy@linux.ibm.com>, <paul.walmsley@sifive.com>,
<palmer@dabbelt.com>, <aou@eecs.berkeley.edu>,
<tglx@linutronix.de>, <ebiederm@xmission.com>,
<akpm@linux-foundation.org>, <bhe@redhat.com>,
<farbere@amazon.com>, <hbathini@linux.ibm.com>,
<sourabhjain@linux.ibm.com>, <adityag@linux.ibm.com>,
<songshuaishuai@tinylab.org>, <takakura@valinux.co.jp>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <linuxppc-dev@lists.ozlabs.org>,
<linux-riscv@lists.infradead.org>, <kexec@lists.infradead.org>
Cc: <jonnyc@amazon.com>
Subject: [PATCH v3 2/2] kexec: Prevent redundant IRQ masking by checking state before shutdown
Date: Thu, 28 Nov 2024 20:10:27 +0000 [thread overview]
Message-ID: <20241128201027.10396-3-farbere@amazon.com> (raw)
In-Reply-To: <20241128201027.10396-1-farbere@amazon.com>
During machine kexec, the function machine_kexec_mask_interrupts() is
responsible for disabling or masking all interrupts. While the irq_disable
hook ensures that an already-disabled IRQ is not disabled again, the
current implementation unconditionally invokes the irq_mask() function for
every interrupt descriptor, even when the interrupt is already masked.
A specific issue was observed in the crash kernel flow after unbinding a
device (prior to kexec) that used a GPIO as an IRQ source. The warning was
triggered by the gpiochip_disable_irq() function, which attempted to clear
the FLAG_IRQ_IS_ENABLED flag when FLAG_USED_AS_IRQ was not set:
```
void gpiochip_disable_irq(struct gpio_chip *gc, unsigned int offset)
{
struct gpio_desc *desc = gpiochip_get_desc(gc, offset);
if (!IS_ERR(desc) &&
!WARN_ON(!test_bit(FLAG_USED_AS_IRQ, &desc->flags)))
clear_bit(FLAG_IRQ_IS_ENABLED, &desc->flags);
}
```
This issue surfaced after commit a8173820f441 ("gpio: gpiolib: Allow GPIO
IRQs to lazy disable") introduced lazy disablement for GPIO IRQs. It
replaced disable/enable hooks with mask/unmask hooks. Unlike the disable
hook, the mask hook doesn't handle already-masked IRQs.
When a GPIO-IRQ driver is unbound, the IRQ is released, triggering
__irq_disable() and irq_state_set_masked(). A subsequent call to
machine_kexec_mask_interrupts() re-invokes chip->irq_mask(). This results
in a call chain, including gpiochip_irq_mask() and gpiochip_disable_irq().
Since FLAG_USED_AS_IRQ was cleared earlier, a warning occurs.
This patch addresses the issue by:
- Replacing the calls to irq_mask() and irq_disable() hooks with a
simplified call to irq_shutdown().
- Checking if the interrupt is started (irqd_is_started) before calling
the shutdown.
As part of this change, the irq_shutdown() declaration was moved from
kernel/irq/internals.h to include/linux/irq.h to make it accessible
outside the kernel/irq/ directory, as the former can only be included
within that directory.
Signed-off-by: Eliav Farber <farbere@amazon.com>
---
V2 -> V3:
- Check if IRQ is started using irqd_is_started().
- Use irq_shutdown() instead of irq_disable().
include/linux/irq.h | 3 +++
kernel/irq/internals.h | 1 -
kernel/kexec_core.c | 8 ++------
3 files changed, 5 insertions(+), 7 deletions(-)
diff --git a/include/linux/irq.h b/include/linux/irq.h
index fa711f80957b..48a3df728c47 100644
--- a/include/linux/irq.h
+++ b/include/linux/irq.h
@@ -694,6 +694,9 @@ extern int irq_chip_request_resources_parent(struct irq_data *data);
extern void irq_chip_release_resources_parent(struct irq_data *data);
#endif
+/* Shut down the interrupt */
+extern void irq_shutdown(struct irq_desc *desc);
+
/* Handling of unhandled and spurious interrupts: */
extern void note_interrupt(struct irq_desc *desc, irqreturn_t action_ret);
diff --git a/kernel/irq/internals.h b/kernel/irq/internals.h
index fe0272cd84a5..1f9287b1ccb7 100644
--- a/kernel/irq/internals.h
+++ b/kernel/irq/internals.h
@@ -88,7 +88,6 @@ extern int irq_activate(struct irq_desc *desc);
extern int irq_activate_and_startup(struct irq_desc *desc, bool resend);
extern int irq_startup(struct irq_desc *desc, bool resend, bool force);
-extern void irq_shutdown(struct irq_desc *desc);
extern void irq_shutdown_and_deactivate(struct irq_desc *desc);
extern void irq_enable(struct irq_desc *desc);
extern void irq_disable(struct irq_desc *desc);
diff --git a/kernel/kexec_core.c b/kernel/kexec_core.c
index 6e1e420946e0..928b4387502b 100644
--- a/kernel/kexec_core.c
+++ b/kernel/kexec_core.c
@@ -1083,7 +1083,7 @@ void machine_kexec_mask_interrupts(void)
int check_eoi = 1;
chip = irq_desc_get_chip(desc);
- if (!chip)
+ if (!chip || !irqd_is_started(&desc->irq_data))
continue;
if (IS_ENABLED(CONFIG_ARM64)) {
@@ -1097,10 +1097,6 @@ void machine_kexec_mask_interrupts(void)
if (check_eoi && chip->irq_eoi && irqd_irq_inprogress(&desc->irq_data))
chip->irq_eoi(&desc->irq_data);
- if (chip->irq_mask)
- chip->irq_mask(&desc->irq_data);
-
- if (chip->irq_disable && !irqd_irq_disabled(&desc->irq_data))
- chip->irq_disable(&desc->irq_data);
+ irq_shutdown(desc);
}
}
--
2.40.1
next prev parent reply other threads:[~2024-11-28 20:11 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-11-28 20:10 [PATCH v3 0/2] Improve interrupt handling during machine kexec Eliav Farber
2024-11-28 20:10 ` [PATCH v3 1/2] kexec: Consolidate machine_kexec_mask_interrupts() implementation Eliav Farber
2024-11-29 2:46 ` kernel test robot
2024-11-29 4:30 ` kernel test robot
2024-11-28 20:10 ` Eliav Farber [this message]
2024-11-29 4:42 ` [PATCH v3 2/2] kexec: Prevent redundant IRQ masking by checking state before shutdown kernel test robot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20241128201027.10396-3-farbere@amazon.com \
--to=farbere@amazon.com \
--cc=adityag@linux.ibm.com \
--cc=akpm@linux-foundation.org \
--cc=aou@eecs.berkeley.edu \
--cc=bhe@redhat.com \
--cc=catalin.marinas@arm.com \
--cc=christophe.leroy@csgroup.eu \
--cc=ebiederm@xmission.com \
--cc=hbathini@linux.ibm.com \
--cc=jonnyc@amazon.com \
--cc=kexec@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=linux@armlinux.org.uk \
--cc=linuxppc-dev@lists.ozlabs.org \
--cc=maddy@linux.ibm.com \
--cc=mpe@ellerman.id.au \
--cc=naveen@kernel.org \
--cc=npiggin@gmail.com \
--cc=palmer@dabbelt.com \
--cc=paul.walmsley@sifive.com \
--cc=songshuaishuai@tinylab.org \
--cc=sourabhjain@linux.ibm.com \
--cc=takakura@valinux.co.jp \
--cc=tglx@linutronix.de \
--cc=will@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).