From: "Isaac Gomez Morales" <isaac.gomez.morales@gmail.com>
To: linuxppc-embedded@ozlabs.org
Subject: MPC8572: Graphic Card problem
Date: Fri, 7 Nov 2008 13:57:38 +0200 [thread overview]
Message-ID: <38a5a2d10811070357x684dcdefg1a43e0891f12ce29@mail.gmail.com> (raw)
[-- Attachment #1: Type: text/plain, Size: 4629 bytes --]
Hi,
I have MPC8572DS Board with
> uname -a
Linux mpc8572ds 2.6.23 #3 SMP
and u-boot 1.3.0.
I have an ATI Radeon 3650 graphics card in the PCIe Slot1 as you can see in
the following charts
> lspci -v
...
0001:03:00.0 Non-VGA unclassified device: Freescale Semiconductor Inc
MPC8572E (rev 10)
!!! Invalid class 0000 for header type 01
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00000000-00000fff
Memory behind bridge: a0000000-bfffffff
Capabilities: [44] Power Management version 2
Capabilities: [4c] Express Root Port (Slot-) IRQ 0
Capabilities: [100] Advanced Error Reporting
0001:04:00.0 VGA compatible controller: ATI Technologies Inc Mobility Radeon
HD 3600 Series (prog-if 00 [VGA controller])
Subsystem: ATI Technologies Inc Unknown device 0b42
Flags: bus master, fast devsel, latency 0, IRQ 18
Memory at a0000000 (64-bit, prefetchable) [size=256M]
Memory at b0000000 (64-bit, non-prefetchable) [size=64K]
I/O ports at 1000 [size=256]
Capabilities: [50] Power Management version 3
Capabilities: [58] Express Legacy Endpoint IRQ 0
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Capabilities: [100] Unknown (11)
The first problem is that the kernel does not seem to know that there is a
kind of pci bridge.
Doing..
> dmesg
...
Found 0001:03:00.0 [1957/0040] 000b20 01
PCI: Calling quirk c045aa60 for 0001:03:00.0
PCI: 0001:03:00.0: class b20 doesn't match header type 01. Ignoring class.
...
PCI: Fixups for bus 0001:03
PCI: Scanning behind PCI bridge 0001:03:00.0, config 010100, pass 0
PCI: Scanning behind PCI bridge 0001:03:00.0, config 000000, pass 1
...
PCI: Cannot allocate resource region 0 of device 0001:04:00.0
got res [a0000000:afffffff] bus [a0000000:afffffff] flags 120c for BAR 0
of 0001:04:00.0
...
vga16fb: initializing
vga16fb: mapped to 0x000a0000
fb0: VGA16 VGA frame buffer device
...
The system cannot allocate de region 0, i believe that is an IO region.
Trying to read de framebuffer
> cat /dev/fb0
__ioremap(): phys addr 0xa0000 is RAM lr c018e838
Unable to handle kernel paging request for data at address 0x000a0000
Faulting instruction address: 0xc0191538
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=2 MPC8572 DS
NIP: c0191538 LR: c01914d4 CTR: 00000400
REGS: e0415e10 TRAP: 0300 Not tainted (2.6.23)
MSR: 00029000 <EE,ME> CR: 40002242 XER: 00000000
DEAR: 000a0000, ESR: 00000000
TASK = efe64530[1085] 'cat' THREAD: e0414000 CPU: 1
GPR00: 00000400 e0415ec0 efe64530 fffffff4 c07635dc 00000000 efffa530
00000000
GPR08: 00000001 e0433000 00000000 000a0000 20002222 1001c648 0ffea000
10090000
GPR16: 10010000 00000002 fffff000 00001000 00000000 00000000 100bbb28
100bec08
GPR24: 00000000 e0433000 00001000 000a0000 00001000 efd8d400 10016000
e0415f20
NIP [c0191538] fb_read+0x148/0x260
LR [c01914d4] fb_read+0xe4/0x260
Call Trace:
[e0415ec0] [c01914d4] fb_read+0xe4/0x260 (unreliable)
[e0415ef0] [c008bf24] vfs_read+0xc4/0x168
[e0415f10] [c008c50c] sys_read+0x4c/0x90
[e0415f40] [c000ffb8] ret_from_syscall+0x0/0x3c
Instruction dump:
7f7be214 3b000000 2b9a1000 39201000 7f9a4f1e 7f2bcb78 7f801671 7c0903a6
41820034 7f6bdb78 7f29cb78 39400000 <800b0000> 394a0001 396b0004 90090000
Segmentation fault
> cat /proc/ioports
00000000-0000ffff : /pcie@ffe08000
00000000-0000ffff : PCI Bus #01
00000020-00000021 : 8259 (master)
000000a0-000000a1 : 8259 (slave)
000004d0-000004d1 : 8259 edge control
00001000-00001fff : PCI Bus #02
00001000-000010ff : 0000:02:1d.0
00001200-00001207 : 0000:02:1f.0
00001200-00001207 : libata
00001208-0000120b : 0000:02:1f.0
00001208-0000120b : libata
00001210-00001217 : 0000:02:1f.0
00001210-00001217 : libata
00001218-0000121b : 0000:02:1f.0
00001218-0000121b : libata
00001220-0000122f : 0000:02:1f.0
00001220-0000122f : libata
00001230-00001237 : 0000:02:1f.1
00001238-0000123b : 0000:02:1f.1
00001240-00001247 : 0000:02:1f.1
00001248-0000124b : 0000:02:1f.1
00001250-0000125f : 0000:02:1f.1
fffdc000-fffebfff : /pcie@ffe0a000
fffee000-ffffdfff : /pcie@ffe09000
fffee000-ffffdfff : PCI Bus #04
fffef000-fffef0ff : 0001:04:00.0
I cant see anything, i have tried differents the lastest version of u-boot
(u-boot-2008) and linux kernel (2.6.27.4) but it dont solve this problem.
All comments will be good.
Thanks in advance and sorry for my english.
Isaac.
[-- Attachment #2: Type: text/html, Size: 6618 bytes --]
reply other threads:[~2008-11-07 11:57 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=38a5a2d10811070357x684dcdefg1a43e0891f12ce29@mail.gmail.com \
--to=isaac.gomez.morales@gmail.com \
--cc=linuxppc-embedded@ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).