From mboxrd@z Thu Jan  1 00:00:00 1970
Message-ID: <3CB59BBD.8060307@pacbell.net>
Date: Thu, 11 Apr 2002 14:20:45 +0000
From: Armin <akuster@pacbell.net>
MIME-Version: 1.0
To: John Tyner <jtyner@cs.ucr.edu>
Cc: linuxppc-embedded@lists.linuxppc.org
Subject: Re: [PATCH] early serial init
References: <Pine.LNX.4.30.0204111259350.23686-100000@hill.cs.ucr.edu>
Content-Type: text/plain; charset=us-ascii; format=flowed
Sender: owner-linuxppc-embedded@lists.linuxppc.org
List-Id: <linuxppc-embedded@lists.linuxppc.org>


John Tyner wrote:
> Here is a patch to setup the serial ports early. It works fine on our
> walnut boards.
>
> --- arch/ppc/platforms/walnut.c.orig	Thu Apr 11 12:55:55 2002
> +++ arch/ppc/platforms/walnut.c	Thu Apr 11 12:58:35 2002
> @@ -31,6 +31,7 @@
>  #include <linux/blk.h>
>  #include <linux/pci.h>
>  #include <linux/rtc.h>
> +#include <linux/serial.h>
>
>  #include <asm/system.h>
>  #include <asm/pci-bridge.h>
> @@ -247,6 +248,11 @@
>  void __init
>  board_init(void)
>  {
> +	struct serial_struct serial_req;
> +	bd_t *bip = (bd_t *) __res;
> +	u32 chrcr;
> +	int div;
> +	ulong bb;
>  #ifdef CONFIG_PPC_RTC
>  	ppc_md.time_init = todc_time_init;
>  	ppc_md.set_rtc_time = todc_set_rtc_time;
> @@ -254,4 +260,40 @@
>  	ppc_md.nvram_read_val = todc_direct_read_val;
>  	ppc_md.nvram_write_val = todc_direct_write_val;
>  #endif
> +	chrcr = mfdcr(DCRN_CHCR0);
> +	div = ((chrcr&0x3e)>>1)+1;
> +	div *= 16;
> +	bb = bip->bi_intfreq/div;
> +
> +	if( !(chrcr & CHR0_U0EC) ){
> +		memset(&serial_req, 0, sizeof(serial_req));
> +		serial_req.line       = 0;
> +		serial_req.baud_base  = bb;
> +		serial_req.port       = 0;
> +		serial_req.irq        = UART0_INT;
> +		serial_req.flags      = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST;
> +		serial_req.io_type    = SERIAL_IO_MEM;
> +		serial_req.iomem_base = (u8 *)UART0_IO_BASE;
> +		serial_req.iomem_reg_shift = 0;
> +
> +		if (early_serial_setup(&serial_req) != 0) {
> +			printk("Early serial init of port 0 failed\n");
> +		}
> +	}
> +
> +	if( !(chrcr & CHR0_U1EC) ){
> +		memset(&serial_req, 0, sizeof(serial_req));
> +		serial_req.line       = 1;
> +		serial_req.baud_base  = bb;
> +		serial_req.port       = 1;
> +		serial_req.irq        = UART1_INT;
> +		serial_req.flags      = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST;
> +		serial_req.io_type    = SERIAL_IO_MEM;
> +		serial_req.iomem_base = (u8 *)UART1_IO_BASE;
> +		serial_req.iomem_reg_shift = 0;
> +
> +		if (early_serial_setup(&serial_req) != 0) {
> +			printk("Early serial init of port 1 failed\n");
> +		}
> +	}
>  }
>
>
>
>
>

I thought we all ready had an early boot for walnut?

armin


** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/