From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Message-ID: <3ECBB43B.2000601@yahoo.co.jp> Date: Thu, 22 May 2003 02:15:39 +0900 From: digitalRNA MIME-Version: 1.0 To: linuxppc-embedded@lists.linuxppc.org Subject: u-boot-0.3.0 + Linux boot failed on walnut Content-Type: text/plain; charset=ISO-2022-JP Sender: owner-linuxppc-embedded@lists.linuxppc.org List-Id: Hello, Now I am trying to boot Linux using u-boot-0.3.0 not openbios on walnut. But it failed. It looks failed around timer initialization on vmlinux. But in the case of openbios, the Linux can boot. Are there any information about this issue? U-Boot 0.3.0 (May 15 2003 - 18:47:55) CPU: IBM PowerPC 405GP Rev. C at 200 MHz (PLB=100, OPB=50, EBC=33 MHz) PCI sync clock at 33 MHz, internal PCI arbiter enabled 16 kB I-Cache 8 kB D-Cache Board: ### No HW ID - assuming WALNUT405 I2C: ready DRAM: 32 MB FLASH: 512 kB In: serial Out: serial Err: serial KGDB: kgdb ready ready BEDBUG:ready Hit any key to stop autoboot: 0 => => tftpboot 0x100000 pImage ENET Speed is 100 Mbps - FULL duplex connection ARP broadcast 1 TFTP from server 9.188.9.24; our IP address is 9.188.9.204 Filename 'pImage'. Load address: 0x100000 Loading: ################################################################# ########################################################### done Bytes transferred = 630421 (99e95 hex) => bootm 0x100000 ## Booting image at 00100000 ... Image Name: Linux-2.4.18_mvl30-walnut Created: 2003-05-19 6:00:19 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 630357 Bytes = 615.6 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK (stop: but cpu is running around timer_interrupt on vmlinux) 405GP 1.15 ROM Monitor (8/9/00) --------------------- System Info ---------------------- Processor = 405GP, PVR: 40110082 Processor speed = 200 MHz PLB speed = 100 MHz OPB speed = 50 MHz Ext Bus speed = 33 MHz PCI Bus speed = 33 MHz (Sync) Amount of SDRAM = 32 MBytes Internal PCI arbiter enabled -------------------------------------------------------- --- Device Configuration --- Power-On Test Devices: 000 Disabled System Memory [RAM] 001 Enabled Ethernet [ENET] 004 Disabled Serial Port 2 [S2] ---------------------------- Boot Sources: 001 Enabled Ethernet [ENET] local=9.188.9.204 remote=9.188.9.24 hwaddr=0004ace30fea 004 Disabled Serial Port 2 [S2] local=8.1.1.2 remote=255.255.255.255 hwaddr=ffffffffffff 005 Enabled Serial Port 1 [S1] Baud = 115200 ---------------------------- Debugger: Disabled ---------------------------- 1 - Enable/disable tests 2 - Enable/disable boot devices 3 - Change IP addresses 4 - Ping test 5 - Toggle ROM monitor debugger 6 - Toggle automatic menu 7 - Display configuration 8 - Save changes to configuration 9 - Set baud rate for s1 boot A - Enable/disable I cache (Enabled ) B - Enable/disable D cache (Disabled) 0 - Exit menu and continue ->0 EMAC0 Ethernet Test OK. ENET Speed is 100 Mbs... FULL duplex connection Booting from [ENET] Ethernet ... Sending bootp request ... ENET: hold frame collision, outbound frame. Loading file "/tftpboot/walnut-linuz" ... Sending tftp boot request ... Transfer Complete ... Loaded successfully ... Entry point at 0x500000 ... loaded at: 00500000 005AE1F8 relocated to: 00400000 004AE1F8 board data at: 004AB128 004AB168 relocated to: 0040546C 004054AC zimage at: 00405A1C 004AAD3E avail ram: 004AF000 02000000 Linux/PPC load: root=/dev/nfs rw ip=on Uncompressing Linux.... Now booting the kernel Linux version 2.4.18_mvl30-walnut (xxx) (gcTIBM Walnut (IBM405GP) Platform ... can boot. Regards, ** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/