From: "David H. Lynch Jr." <dhlii@dlasys.net>
To: linuxppc-embedded@ozlabs.org
Subject: Re: Ethernet driver for Linux kernel 2.6 running on ML403
Date: Thu, 14 Sep 2006 07:18:44 -0400 [thread overview]
Message-ID: <45093A94.2080407@dlasys.net> (raw)
In-Reply-To: <528646bc0609131852s41a8bc4ev44b84d68f51b1d2d@mail.gmail.com>
[-- Attachment #1: Type: text/plain, Size: 2188 bytes --]
Grant Likely wrote:
> On 9/13/06, Aleck Lin <aleck@gdatech.com> wrote:
>
>> Hi,
>>
>> I'm able to boot Linux 2.6 on ML403 board (with a ramdisk file system).
>>
>> However, during the kernel booting, it complains that "No network devices
>> available," So I figured I probably didn't enable the ethernet driver in the
>> kernel.
>>
>> >From doing "make menuconfig", under "Device Drivers" --> "Network device
>> support" --> "Ethernet(10 or 100Mbit)", I checked the box of both "Ethernet
>> (10 or 100Mbit)" and "PowerPC 4xx on-chip Ethernet support." I then
>> save/exit the menuconfig to compile the kernel again. I've attached the
>> error output at the bottom.
>>
>
> The virtex eth device is not the same as 4xx on-chip Ethernet, so
> CONFIG_IBM_EMAC will not work. You need the xilinx_enet driver (which
> is not in mainline). It might be in MontaVista's 2.6 tree.
>
> I think people have posted patches for it to this list, so try
> searching the archives. (I don't have a link off the top of my head.)
>
The MV 2.6 Xilinx_edk based TEMAC driver has been posted to this
list several times.
As of the last incarnation I tried it had no MII/PHY support and you
had to manully change the speed of the driver 10/100/1000 by editing the
code.
Otherwise it worked with the PLB FIFO TEMAC, that I am using, and
should with others.
I have a polled driver that works with the LL TEMAC.
I am nearly finished a PLB FIFO TEMAC driver that includes working
autonegotiation and does not use the Xilinx_edk.
But right now it has a receive problem - packets come in they look
good but linux silently discards them.
I have virtually the same code working under GHS Integrity.
--
Dave Lynch DLA Systems
Software Development: Embedded Linux
717.627.3770 dhlii@dlasys.net http://www.dlasys.net
fax: 1.253.369.9244 Cell: 1.717.587.7774
Over 25 years' experience in platforms, languages, and technologies too numerous to list.
"Any intelligent fool can make things bigger and more complex... It takes a touch of genius - and a lot of courage to move in the opposite direction."
Albert Einstein
[-- Attachment #2: Type: text/html, Size: 2992 bytes --]
next prev parent reply other threads:[~2006-09-14 11:20 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <mailman.241.1158193867.2423.linuxppc-embedded@ozlabs.org>
2006-09-14 1:40 ` Ethernet driver for Linux kernel 2.6 running on ML403 Aleck Lin
2006-09-14 1:48 ` Eugene Surovegin
2006-09-14 1:52 ` Grant Likely
2006-09-14 11:18 ` David H. Lynch Jr. [this message]
2006-09-14 13:53 ` Michael Galassi
2006-09-14 14:34 ` Grant Likely
2006-09-14 15:47 ` Keith J Outwater
2006-09-14 22:57 ` Grant Likely
2006-09-19 7:48 ` Peter Korsgaard
2006-09-19 14:17 ` Grant Likely
2006-09-19 20:10 ` Grant Likely
2006-09-19 20:40 ` David H. Lynch Jr.
2006-09-19 21:27 ` Grant Likely
2006-09-24 5:42 ` David H. Lynch Jr.
2006-09-24 14:35 ` Grant Likely
2006-09-14 23:02 ` David H. Lynch Jr.
2006-09-14 16:40 John Bonesio
2006-09-14 17:36 ` Keith J Outwater
2006-09-14 22:02 ` T Ziomek
2006-09-14 23:16 ` David H. Lynch Jr.
2006-09-14 22:49 ` Grant Likely
2006-09-15 16:11 ` T Ziomek
2006-09-19 10:13 ` Peter Korsgaard
2006-09-19 18:06 ` Andrew
-- strict thread matches above, loose matches on Subject: below --
2006-09-14 17:52 John Bonesio
2006-09-14 23:08 ` Keith J Outwater
2006-09-15 0:08 ` David H. Lynch Jr.
2006-09-15 1:14 ` David H. Lynch Jr.
2006-09-15 19:13 John Bonesio
2006-09-19 14:16 ` Grant Likely
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=45093A94.2080407@dlasys.net \
--to=dhlii@dlasys.net \
--cc=linuxppc-embedded@ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).