* system ace programming xf60 @ 2006-12-14 16:05 Wade Maxfield 2006-12-14 19:20 ` Peter Ryser 0 siblings, 1 reply; 5+ messages in thread From: Wade Maxfield @ 2006-12-14 16:05 UTC (permalink / raw) To: ppc [-- Attachment #1: Type: text/plain, Size: 1367 bytes --] Hi, We are trying to generate a system ace file that will program an xf60 using Xilinx scripts, (and even their impact GUI), using 8.1i, service pack 3 EDK. Unfortunately, if we choose the ml410 board from Xilinx's genace.tclscript in their EDK/data/xmd directory, it errors with an invalid instruction register length. The irlength is listed as 14 in the xilinx script files. I looked and googled and could not find the irlength listed for that xf60 part in any literature. Also, if we try to include the zImage.elf file, the script errors out. Conversely, if we choose an ml403 board (and switch the project to the xf12 chip), we can combine the zImage.elf file and generate a system.ace file that loads on an ml403 board. We can take the download.bit file that refuses to load when combined into the system.ace, and load it over the jtag port. It programs the xf60 just fine. If we create an empty system.ace file, the system ace chip on our board signals everything is ok, but of course, the xilinx chip is not programmed. If we pull the compact flash out of the board, the system ace chip signals that is can't find the compact flash by flashing the error light. Has anyone on this list had any experience with this that could lead us in a right direction? We've tried about 10 different combinations so far with no luck. thanks, wade [-- Attachment #2: Type: text/html, Size: 1522 bytes --] ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: system ace programming xf60 2006-12-14 16:05 system ace programming xf60 Wade Maxfield @ 2006-12-14 19:20 ` Peter Ryser 2006-12-14 19:46 ` Wade Maxfield 0 siblings, 1 reply; 5+ messages in thread From: Peter Ryser @ 2006-12-14 19:20 UTC (permalink / raw) To: ppc [-- Attachment #1: Type: text/plain, Size: 2139 bytes --] Wade, the v4fx60 has two PPC405. Please make sure that both PPC405 are connected to the jtagppc_cntrl in your MHS hardware project file. You might want to compare your setup with the ML410 reference design available at http://www.xilinx.com/products/boards/ml410/designs/ml410_bsb_design.zip. The JTAG IR length of the v4fx60 is 14 (6 for the FPGA + 4 for each PPC405, i.e. for the 4vfx60 it's 6+4+4=14) - Peter Wade Maxfield wrote: > Hi, > > We are trying to generate a system ace file that will program an > xf60 using Xilinx scripts, > (and even their impact GUI), using 8.1i, service pack 3 EDK. > > Unfortunately, if we choose the ml410 board from Xilinx's genace.tcl > script > in their EDK/data/xmd directory, it errors with an invalid instruction > register length. > The irlength is listed as 14 in the xilinx script files. I looked and > googled and could > not find the irlength listed for that xf60 part in any literature. > > Also, if we try to include the zImage.elf file, the script errors out. > > Conversely, if we choose an ml403 board (and switch the project to > the xf12 chip), > we can combine the zImage.elf file and generate a system.ace file that > loads on an > ml403 board. > > We can take the download.bit file that refuses to load when combined > into the system.ace, > and load it over the jtag port. It programs the xf60 just fine. > > If we create an empty system.ace file, the system ace chip on our > board signals everything is ok, > but of course, the xilinx chip is not programmed. If we pull the > compact flash out of the board, > the system ace chip signals that is can't find the compact flash by > flashing the error light. > > Has anyone on this list had any experience with this that could lead > us in a right direction? We've > tried about 10 different combinations so far with no luck. > > thanks, > wade > >------------------------------------------------------------------------ > >_______________________________________________ >Linuxppc-embedded mailing list >Linuxppc-embedded@ozlabs.org >https://ozlabs.org/mailman/listinfo/linuxppc-embedded > [-- Attachment #2: Type: text/html, Size: 2896 bytes --] ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: system ace programming xf60 2006-12-14 19:20 ` Peter Ryser @ 2006-12-14 19:46 ` Wade Maxfield 0 siblings, 0 replies; 5+ messages in thread From: Wade Maxfield @ 2006-12-14 19:46 UTC (permalink / raw) To: Peter Ryser; +Cc: ppc [-- Attachment #1: Type: text/plain, Size: 2882 bytes --] Hi Peter, Thanks, we had that already. The 8.1i development environment refused to build until we fixed that. See my other reply to let you know how we did it. The genace.tcl file shipped with 8.1i (service pack 3) has an incorrect ID code for the xf60 part. That threw us off for over a day, as the tool can't find an irlength for that invalid part (since the part ID does not exist.) Rather than erroring with an "invalid id code," it gives an "invalid instruction length" error, which was not useful at that time. thanks, wade On 12/14/06, Peter Ryser <peter.ryser@xilinx.com> wrote: > > Wade, > > the v4fx60 has two PPC405. Please make sure that both PPC405 are connected > to the jtagppc_cntrl in your MHS hardware project file. You might want to > compare your setup with the ML410 reference design available at > http://www.xilinx.com/products/boards/ml410/designs/ml410_bsb_design.zip. > > The JTAG IR length of the v4fx60 is 14 (6 for the FPGA + 4 for each > PPC405, i.e. for the 4vfx60 it's 6+4+4=14) > > - Peter > > > Wade Maxfield wrote: > > Hi, > > We are trying to generate a system ace file that will program an xf60 > using Xilinx scripts, > (and even their impact GUI), using 8.1i, service pack 3 EDK. > > Unfortunately, if we choose the ml410 board from Xilinx's genace.tclscript > in their EDK/data/xmd directory, it errors with an invalid instruction > register length. > The irlength is listed as 14 in the xilinx script files. I looked and > googled and could > not find the irlength listed for that xf60 part in any literature. > > Also, if we try to include the zImage.elf file, the script errors out. > > Conversely, if we choose an ml403 board (and switch the project to the > xf12 chip), > we can combine the zImage.elf file and generate a system.ace file that > loads on an > ml403 board. > > We can take the download.bit file that refuses to load when combined > into the system.ace, > and load it over the jtag port. It programs the xf60 just fine. > > If we create an empty system.ace file, the system ace chip on our board > signals everything is ok, > but of course, the xilinx chip is not programmed. If we pull the compact > flash out of the board, > the system ace chip signals that is can't find the compact flash by > flashing the error light. > > Has anyone on this list had any experience with this that could lead us > in a right direction? We've > tried about 10 different combinations so far with no luck. > > thanks, > wade > > ------------------------------ > > _______________________________________________ > Linuxppc-embedded mailing list > Linuxppc-embedded@ozlabs.orghttps://ozlabs.org/mailman/listinfo/linuxppc-embedded > > > _______________________________________________ > Linuxppc-embedded mailing list > Linuxppc-embedded@ozlabs.org > https://ozlabs.org/mailman/listinfo/linuxppc-embedded > > [-- Attachment #2: Type: text/html, Size: 4282 bytes --] ^ permalink raw reply [flat|nested] 5+ messages in thread
[parent not found: <8506C3905ED0764F889ADEB33E3A9E8062CF8A@MAIA.scopus.net>]
* Re: system ace programming xf60 [not found] <8506C3905ED0764F889ADEB33E3A9E8062CF8A@MAIA.scopus.net> @ 2006-12-14 19:14 ` Wade Maxfield 2006-12-14 19:41 ` Wade Maxfield 0 siblings, 1 reply; 5+ messages in thread From: Wade Maxfield @ 2006-12-14 19:14 UTC (permalink / raw) To: Sharon Feldman; +Cc: ppc [-- Attachment #1: Type: text/plain, Size: 3184 bytes --] Hi Sharon, Thank you! I found the irlength (called INSTRUCTION_LENGTH) in the file xc4vfx60_ff1152.bsd and it is indeed 14. We are running a custom board that looks like an ml410, with only one device, the xf60 (in addition to the system ace chip), which is exactly what the genace.tcl file specifies. We do have a cpld as a second part, but we are not programming it. The genace.tcl file in the Xininx/data/xmd directory was incorrect in how it listed the device IDCODE on the part. It had 0x01eb409, the real code is 0x1EB4093. Once the code was fixed in the file, the genace.tcl created system.ace bundling the zImage.elf file into it correctly. However, we are not yet getting a xilinx program load. Onward through the fog! We can program the xilinx through the system ace using the jtag, but we cannot get the system ace to program it from the system.ace on the compact flash, generated using the same download.bit we use over the jtag. wade On 12/14/06, Sharon Feldman <sharonf@scopus.net> wrote: > > the INSTRUCTION_LENGTH attribute can be found in The Device BSDL File. > > As Much As I Know It Is 14 For All FX60 Devices. > > BSDL .bsd File Are Found Under : > > C:\Xilinx\virtex4\data > > Are You Sure You Are Accessing The Wright Device On The Chain ? > It Is Possible That The Number Of Xilinx FPGA Has Changed In ML410. (It Is > 3 In ML403), > In ML410 There Is No CPLD, So I Guess It Is Probebly 2 Now. > > > -----Original Message----- > *From:* linuxppc-embedded-bounces+sharonf=scopus.net@ozlabs.org [mailto: > linuxppc-embedded-bounces+sharonf=scopus.net@ozlabs.org]*On Behalf Of *Wade > Maxfield > *Sent:* Thursday, December 14, 2006 6:06 PM > *To:* ppc > *Subject:* system ace programming xf60 > > Hi, > > We are trying to generate a system ace file that will program an xf60 > using Xilinx scripts, > (and even their impact GUI), using 8.1i, service pack 3 EDK. > > Unfortunately, if we choose the ml410 board from Xilinx's genace.tclscript > in their EDK/data/xmd directory, it errors with an invalid instruction > register length. > The irlength is listed as 14 in the xilinx script files. I looked and > googled and could > not find the irlength listed for that xf60 part in any literature. > > Also, if we try to include the zImage.elf file, the script errors out. > > Conversely, if we choose an ml403 board (and switch the project to the > xf12 chip), > we can combine the zImage.elf file and generate a system.ace file that > loads on an > ml403 board. > > We can take the download.bit file that refuses to load when combined > into the system.ace, > and load it over the jtag port. It programs the xf60 just fine. > > If we create an empty system.ace file, the system ace chip on our board > signals everything is ok, > but of course, the xilinx chip is not programmed. If we pull the compact > flash out of the board, > the system ace chip signals that is can't find the compact flash by > flashing the error light. > > Has anyone on this list had any experience with this that could lead us > in a right direction? We've > tried about 10 different combinations so far with no luck. > > thanks, > wade > > [-- Attachment #2: Type: text/html, Size: 5062 bytes --] ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: system ace programming xf60 2006-12-14 19:14 ` Wade Maxfield @ 2006-12-14 19:41 ` Wade Maxfield 0 siblings, 0 replies; 5+ messages in thread From: Wade Maxfield @ 2006-12-14 19:41 UTC (permalink / raw) To: Sharon Feldman; +Cc: ppc [-- Attachment #1: Type: text/plain, Size: 4189 bytes --] We Got It! The mention of the cpld's on the ml410 board by Feldman caused me to try something that worked. The .bsd file did indeed contain the irlength. The idcode for the part was incorrect in the shipped genace.tcl file (but correct in the xilinx book). The final key was the CPLD we had on the JTAG chain HAD TO BE LISTED as a "-configdevice devicenr 2 irlength 8 partname xc2c128" in the parameter string before the system ace would program up the xilinx chip without showing an error. Evidently the system ace has to see the all of the parts on the jtag chain listed in the system.ace file or it will refuse to program any device at all. (Unless you have NO devices listed in the system.ace file. In that case it is also happy.) thanks again, wade On 12/14/06, Wade Maxfield <wmaxfield@gmail.com> wrote: > > Hi Sharon, > > Thank you! I found the irlength (called INSTRUCTION_LENGTH) in the > file xc4vfx60_ff1152.bsd and it is indeed 14. > > We are running a custom board that looks like an ml410, with only one > device, the xf60 (in addition to the system ace chip), which is exactly what > the genace.tcl file specifies. We do have a cpld as a second part, but > we are not programming it. The genace.tcl file in the Xininx/data/xmd > directory was incorrect in how it listed the device IDCODE on the part. It > had 0x01eb409, the real code is 0x1EB4093. Once the code was fixed in the > file, the genace.tcl created system.ace bundling the zImage.elf file into > it correctly. > > However, we are not yet getting a xilinx program load. Onward through > the fog! > > We can program the xilinx through the system ace using the jtag, but > we cannot get the system ace to program it from the system.ace on the > compact flash, generated using the same download.bit we use over the jtag. > > wade > > > > On 12/14/06, Sharon Feldman < sharonf@scopus.net> wrote: > > > > the INSTRUCTION_LENGTH attribute can be found in The Device BSDL File. > > > > As Much As I Know It Is 14 For All FX60 Devices. > > > > BSDL .bsd File Are Found Under : > > > > C:\Xilinx\virtex4\data > > > > Are You Sure You Are Accessing The Wright Device On The Chain ? > > It Is Possible That The Number Of Xilinx FPGA Has Changed In ML410. (It > > Is 3 In ML403), > > In ML410 There Is No CPLD, So I Guess It Is Probebly 2 Now. > > > > > > -----Original Message----- > > *From:* linuxppc-embedded-bounces+sharonf=scopus.net@ozlabs.org [mailto: > > linuxppc-embedded-bounces+sharonf=scopus.net@ozlabs.org]*On Behalf Of *Wade > > Maxfield > > *Sent:* Thursday, December 14, 2006 6:06 PM > > *To:* ppc > > *Subject:* system ace programming xf60 > > > > Hi, > > > > We are trying to generate a system ace file that will program an xf60 > > using Xilinx scripts, > > (and even their impact GUI), using 8.1i, service pack 3 EDK. > > > > Unfortunately, if we choose the ml410 board from Xilinx's genace.tclscript > > in their EDK/data/xmd directory, it errors with an invalid instruction > > register length. > > The irlength is listed as 14 in the xilinx script files. I looked and > > googled and could > > not find the irlength listed for that xf60 part in any literature. > > > > Also, if we try to include the zImage.elf file, the script errors out. > > > > Conversely, if we choose an ml403 board (and switch the project to the > > xf12 chip), > > we can combine the zImage.elf file and generate a system.ace file that > > loads on an > > ml403 board. > > > > We can take the download.bit file that refuses to load when combined > > into the system.ace, > > and load it over the jtag port. It programs the xf60 just fine. > > > > If we create an empty system.ace file, the system ace chip on our > > board signals everything is ok, > > but of course, the xilinx chip is not programmed. If we pull the > > compact flash out of the board, > > the system ace chip signals that is can't find the compact flash by > > flashing the error light. > > > > Has anyone on this list had any experience with this that could lead > > us in a right direction? We've > > tried about 10 different combinations so far with no luck. > > > > thanks, > > wade > > > > > [-- Attachment #2: Type: text/html, Size: 6420 bytes --] ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2006-12-14 19:46 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2006-12-14 16:05 system ace programming xf60 Wade Maxfield
2006-12-14 19:20 ` Peter Ryser
2006-12-14 19:46 ` Wade Maxfield
[not found] <8506C3905ED0764F889ADEB33E3A9E8062CF8A@MAIA.scopus.net>
2006-12-14 19:14 ` Wade Maxfield
2006-12-14 19:41 ` Wade Maxfield
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).