* AMCC yosemite 440ep PCI slot doesn't work.
@ 2007-09-21 10:53 Andrew Liu
2007-09-21 15:14 ` Valentine Barshak
0 siblings, 1 reply; 9+ messages in thread
From: Andrew Liu @ 2007-09-21 10:53 UTC (permalink / raw)
To: linuxppc-dev
Hello All,
when insert a RealTek RTL8139 network card into PCI slot,
After system boot up,
root@localhost:/root> ifconfig eth2 192.168.17.12
irq 25: nobody cared (try booting with the "irqpoll" option)
Call Trace:
[cf135af0] [c0008820] show_stack+0x48/0x190 (unreliable)
[cf135b20] [c003c414] __report_bad_irq+0x34/0xac
[cf135b40] [c003c714] note_interrupt+0x288/0x2c8
[cf135b70] [c003b818] __do_IRQ+0x104/0x110
[cf135b90] [c0006900] do_IRQ+0xbc/0xc0
[cf135ba0] [c00020c0] ret_from_except+0x0/0x18
[cf135c60] [00000019] 0x19
[cf135c90] [c000668c] do_softirq+0x54/0x58
[cf135ca0] [c001df40] irq_exit+0x48/0x58
[cf135cb0] [c00068b4] do_IRQ+0x70/0xc0
[cf135cc0] [c00020c0] ret_from_except+0x0/0x18
[cf135d80] [c003c2b4] setup_irq+0x1ac/0x200
[cf135da0] [c003c3cc] request_irq+0xc4/0xd8
[cf135dd0] [c0122328] rtl8139_open+0x38/0x210
[cf135df0] [c0187500] dev_open+0x7c/0xcc
[cf135e10] [c0187420] dev_change_flags+0x16c/0x1d0
[cf135e30] [c01cbff0] devinet_ioctl+0x604/0x720
[cf135ea0] [c01cc1f8] inet_ioctl+0x98/0xbc
[cf135eb0] [c0179328] sock_ioctl+0x60/0x260
[cf135ed0] [c006c360] do_ioctl+0x38/0x84
[cf135ee0] [c006c438] vfs_ioctl+0x8c/0x40c
[cf135f10] [c006c7f8] sys_ioctl+0x40/0x74
[cf135f40] [c0001a84] ret_from_syscall+0x0/0x3c
handlers:
[<c0122bd4>] (rtl8139_interrupt+0x0/0x52c)
Disabling IRQ #25
root@localhost:/root>
Message from syslogd@localhost at Thu Jan 1 00:02:13 1970 ...
localhost kernel: Disabling IRQ #25
root@localhost:/root>
The system boot up information as follows:
root@localhost:/root> dmesg
Linux version 2.6.23-rc6-gea60adb5 (sliu@localhost.localdomain) (gcc
version 4.0.0 (DENX ELDK 4.1 4.0.0)) #3 Fri Sep 21 18:37:59 CST 2007
AMCC PowerPC 440EP Yosemite Platform
Entering add_active_range(0, 0, 65536) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 65536
Normal 65536 -> 65536
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 65536
On node 0 totalpages: 65536
DMA zone: 512 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 65024 pages, LIFO batch:15
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order. Total pages: 65024
Kernel command line: root=/dev/nfs rw
nfsroot=128.224.149.6:/tftpboot/sliu/rootfs
ip=128.224.149.11::128.224.149.1:255.255.255.0:yosemite:eth0:off
console=ttyS0,9600
PID hash table entries: 1024 (order: 10, 4096 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256896k available (2052k kernel code, 716k data, 152k init, 0k
highmem)
Calibrating delay loop... 798.72 BogoMIPS (lpj=1597440)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Probing PCI hardware
PCI: Scanning bus 0000:00
PCI: Found 0000:00:0c.0 [10ec/8139] 000200 00
PCI: Calling quirk c000444c for 0000:00:0c.0
PCI: Fixups for bus 0000:00
PCI: Bus scan for 0000:00 returning with max=00
PCI: fixup irq: (0000:00:0c.0) got 25
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
PCI: Calling quirk c00fbab4 for 0000:00:0c.0
PCI: Calling quirk c02ae3b8 for 0000:00:0c.0
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x0 (irq = 0) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 1) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
PPC 4xx OCP EMAC driver, version 3.54
mal0: initialized, 4 TX channels, 2 RX channels
zmii0: bridge in RMII mode
eth0: emac0, MAC 00:10:ec:00:87:42
eth0: found Generic MII PHY (0x01)
eth1: emac1, MAC 00:00:00:00:00:00
eth1: found Generic MII PHY (0x03)
8139too Fast Ethernet driver 0.9.28
eth2: RealTek RTL8139 at 0xd1012f00, 00:0e:2e:7e:f5:e6, IRQ 25
eth2: Identified 8139 chip type 'RTL-8100B/8139D'
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
usbmon: debugfs is not available
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ppc-soc-ohci ppc-soc-ohci.0: USB Host Controller
ppc-soc-ohci ppc-soc-ohci.0: new USB bus registered, assigned bus number 1
ppc-soc-ohci ppc-soc-ohci.0: irq 40, io mem 0xef601000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ether gadget: using random self ethernet address
ether gadget: using random host ethernet address
usb0: Ethernet Gadget, version: May Day 2005
usb0: using musbhsfc_udc, OUT ep2 IN ep1 STATUS ep3
usb0: MAC 66:91:74:ab:fb:61
usb0: HOST MAC 1a:b5:87:5d:8f:00
usb0: RNDIS ready
musbhsfc_udc: registered gadget driver 'ether'
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
usb 1-1: new full speed USB device using ppc-soc-ohci and address 2
usb 1-1: configuration #1 chosen from 1 choice
eth0: link is up, 100 FDX, pause enabled
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
IP-Config: Complete:
device=eth0, addr=128.224.149.11, mask=255.255.255.0,
gw=128.224.149.1,
host=yosemite, domain=, nis-domain=(none),
bootserver=255.255.255.255, rootserver=128.224.149.6, rootpath=
Looking up port of RPC 100003/2 on 128.224.149.6
Looking up port of RPC 100005/1 on 128.224.149.6
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 152k init
scsi 0:0:0:0: Direct-Access Kingston DataTraveler 2.0 6.16 PQ: 0
ANSI: 0 CCS
sd 0:0:0:0: [sda] 244735 512-byte hardware sectors (125 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 45 00 00 08
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 244735 512-byte hardware sectors (125 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 45 00 00 08
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
irq 25: nobody cared (try booting with the "irqpoll" option)
Call Trace:
[cf135af0] [c0008820] show_stack+0x48/0x190 (unreliable)
[cf135b20] [c003c414] __report_bad_irq+0x34/0xac
[cf135b40] [c003c714] note_interrupt+0x288/0x2c8
[cf135b70] [c003b818] __do_IRQ+0x104/0x110
[cf135b90] [c0006900] do_IRQ+0xbc/0xc0
[cf135ba0] [c00020c0] ret_from_except+0x0/0x18
[cf135c60] [00000019] 0x19
[cf135c90] [c000668c] do_softirq+0x54/0x58
[cf135ca0] [c001df40] irq_exit+0x48/0x58
[cf135cb0] [c00068b4] do_IRQ+0x70/0xc0
[cf135cc0] [c00020c0] ret_from_except+0x0/0x18
[cf135d80] [c003c2b4] setup_irq+0x1ac/0x200
[cf135da0] [c003c3cc] request_irq+0xc4/0xd8
[cf135dd0] [c0122328] rtl8139_open+0x38/0x210
[cf135df0] [c0187500] dev_open+0x7c/0xcc
[cf135e10] [c0187420] dev_change_flags+0x16c/0x1d0
[cf135e30] [c01cbff0] devinet_ioctl+0x604/0x720
[cf135ea0] [c01cc1f8] inet_ioctl+0x98/0xbc
[cf135eb0] [c0179328] sock_ioctl+0x60/0x260
[cf135ed0] [c006c360] do_ioctl+0x38/0x84
[cf135ee0] [c006c438] vfs_ioctl+0x8c/0x40c
[cf135f10] [c006c7f8] sys_ioctl+0x40/0x74
[cf135f40] [c0001a84] ret_from_syscall+0x0/0x3c
handlers:
[<c0122bd4>] (rtl8139_interrupt+0x0/0x52c)
Disabling IRQ #25
eth2: link up, 100Mbps, full-duplex, lpa 0x45E1
Who can give some advice?
Thanks.
BRs,
Andrew.
^ permalink raw reply [flat|nested] 9+ messages in thread* Re: AMCC yosemite 440ep PCI slot doesn't work.
2007-09-21 10:53 AMCC yosemite 440ep PCI slot doesn't work Andrew Liu
@ 2007-09-21 15:14 ` Valentine Barshak
2007-09-24 9:34 ` Andrew Liu
0 siblings, 1 reply; 9+ messages in thread
From: Valentine Barshak @ 2007-09-21 15:14 UTC (permalink / raw)
To: Andrew Liu; +Cc: linuxppc-dev
Andrew Liu wrote:
> Hello All,
>
> when insert a RealTek RTL8139 network card into PCI slot,
> After system boot up,
>
> root@localhost:/root> ifconfig eth2 192.168.17.12
> irq 25: nobody cared (try booting with the "irqpoll" option)
> Call Trace:
> [cf135af0] [c0008820] show_stack+0x48/0x190 (unreliable)
> [cf135b20] [c003c414] __report_bad_irq+0x34/0xac
> [cf135b40] [c003c714] note_interrupt+0x288/0x2c8
> [cf135b70] [c003b818] __do_IRQ+0x104/0x110
> [cf135b90] [c0006900] do_IRQ+0xbc/0xc0
> [cf135ba0] [c00020c0] ret_from_except+0x0/0x18
> [cf135c60] [00000019] 0x19
> [cf135c90] [c000668c] do_softirq+0x54/0x58
> [cf135ca0] [c001df40] irq_exit+0x48/0x58
> [cf135cb0] [c00068b4] do_IRQ+0x70/0xc0
> [cf135cc0] [c00020c0] ret_from_except+0x0/0x18
> [cf135d80] [c003c2b4] setup_irq+0x1ac/0x200
> [cf135da0] [c003c3cc] request_irq+0xc4/0xd8
> [cf135dd0] [c0122328] rtl8139_open+0x38/0x210
> [cf135df0] [c0187500] dev_open+0x7c/0xcc
> [cf135e10] [c0187420] dev_change_flags+0x16c/0x1d0
> [cf135e30] [c01cbff0] devinet_ioctl+0x604/0x720
> [cf135ea0] [c01cc1f8] inet_ioctl+0x98/0xbc
> [cf135eb0] [c0179328] sock_ioctl+0x60/0x260
> [cf135ed0] [c006c360] do_ioctl+0x38/0x84
> [cf135ee0] [c006c438] vfs_ioctl+0x8c/0x40c
> [cf135f10] [c006c7f8] sys_ioctl+0x40/0x74
> [cf135f40] [c0001a84] ret_from_syscall+0x0/0x3c
> handlers:
> [<c0122bd4>] (rtl8139_interrupt+0x0/0x52c)
> Disabling IRQ #25
> root@localhost:/root>
> Message from syslogd@localhost at Thu Jan 1 00:02:13 1970 ...
> localhost kernel: Disabling IRQ #25
>
> root@localhost:/root>
>
>
> The system boot up information as follows:
> root@localhost:/root> dmesg
> Linux version 2.6.23-rc6-gea60adb5 (sliu@localhost.localdomain) (gcc
> version 4.0.0 (DENX ELDK 4.1 4.0.0)) #3 Fri Sep 21 18:37:59 CST 2007
> AMCC PowerPC 440EP Yosemite Platform
> Entering add_active_range(0, 0, 65536) 0 entries of 256 used
> Zone PFN ranges:
> DMA 0 -> 65536
> Normal 65536 -> 65536
> Movable zone start PFN for each node
> early_node_map[1] active PFN ranges
> 0: 0 -> 65536
> On node 0 totalpages: 65536
> DMA zone: 512 pages used for memmap
> DMA zone: 0 pages reserved
> DMA zone: 65024 pages, LIFO batch:15
> Normal zone: 0 pages used for memmap
> Movable zone: 0 pages used for memmap
> Built 1 zonelists in Zone order. Total pages: 65024
> Kernel command line: root=/dev/nfs rw
> nfsroot=128.224.149.6:/tftpboot/sliu/rootfs
> ip=128.224.149.11::128.224.149.1:255.255.255.0:yosemite:eth0:off
> console=ttyS0,9600
> PID hash table entries: 1024 (order: 10, 4096 bytes)
> console [ttyS0] enabled
> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> Memory: 256896k available (2052k kernel code, 716k data, 152k init, 0k
> highmem)
> Calibrating delay loop... 798.72 BogoMIPS (lpj=1597440)
> Mount-cache hash table entries: 512
> NET: Registered protocol family 16
> PCI: Probing PCI hardware
> PCI: Scanning bus 0000:00
> PCI: Found 0000:00:0c.0 [10ec/8139] 000200 00
> PCI: Calling quirk c000444c for 0000:00:0c.0
> PCI: Fixups for bus 0000:00
> PCI: Bus scan for 0000:00 returning with max=00
> PCI: fixup irq: (0000:00:0c.0) got 25
> SCSI subsystem initialized
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> NET: Registered protocol family 2
> IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
> TCP established hash table entries: 8192 (order: 4, 65536 bytes)
> TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
> TCP: Hash tables configured (established 8192 bind 8192)
> TCP reno registered
> io scheduler noop registered
> io scheduler anticipatory registered (default)
> io scheduler deadline registered
> io scheduler cfq registered
> PCI: Calling quirk c00fbab4 for 0000:00:0c.0
> PCI: Calling quirk c02ae3b8 for 0000:00:0c.0
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
> serial8250: ttyS0 at MMIO 0x0 (irq = 0) is a 16550A
> serial8250: ttyS1 at MMIO 0x0 (irq = 1) is a 16550A
> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
> PPC 4xx OCP EMAC driver, version 3.54
> mal0: initialized, 4 TX channels, 2 RX channels
> zmii0: bridge in RMII mode
> eth0: emac0, MAC 00:10:ec:00:87:42
> eth0: found Generic MII PHY (0x01)
> eth1: emac1, MAC 00:00:00:00:00:00
> eth1: found Generic MII PHY (0x03)
> 8139too Fast Ethernet driver 0.9.28
> eth2: RealTek RTL8139 at 0xd1012f00, 00:0e:2e:7e:f5:e6, IRQ 25
> eth2: Identified 8139 chip type 'RTL-8100B/8139D'
> pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
> usbcore: registered new interface driver pegasus
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> usbmon: debugfs is not available
> ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
> ppc-soc-ohci ppc-soc-ohci.0: USB Host Controller
> ppc-soc-ohci ppc-soc-ohci.0: new USB bus registered, assigned bus number 1
> ppc-soc-ohci ppc-soc-ohci.0: irq 40, io mem 0xef601000
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 2 ports detected
> Initializing USB Mass Storage driver...
> usbcore: registered new interface driver usb-storage
> USB Mass Storage support registered.
> ether gadget: using random self ethernet address
> ether gadget: using random host ethernet address
> usb0: Ethernet Gadget, version: May Day 2005
> usb0: using musbhsfc_udc, OUT ep2 IN ep1 STATUS ep3
> usb0: MAC 66:91:74:ab:fb:61
> usb0: HOST MAC 1a:b5:87:5d:8f:00
> usb0: RNDIS ready
> musbhsfc_udc: registered gadget driver 'ether'
> TCP cubic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> usb 1-1: new full speed USB device using ppc-soc-ohci and address 2
> usb 1-1: configuration #1 chosen from 1 choice
> eth0: link is up, 100 FDX, pause enabled
> scsi0 : SCSI emulation for USB Mass Storage devices
> usb-storage: device found at 2
> usb-storage: waiting for device to settle before scanning
> IP-Config: Complete:
> device=eth0, addr=128.224.149.11, mask=255.255.255.0,
> gw=128.224.149.1,
> host=yosemite, domain=, nis-domain=(none),
> bootserver=255.255.255.255, rootserver=128.224.149.6, rootpath=
> Looking up port of RPC 100003/2 on 128.224.149.6
> Looking up port of RPC 100005/1 on 128.224.149.6
> VFS: Mounted root (nfs filesystem).
> Freeing unused kernel memory: 152k init
> scsi 0:0:0:0: Direct-Access Kingston DataTraveler 2.0 6.16 PQ: 0
> ANSI: 0 CCS
> sd 0:0:0:0: [sda] 244735 512-byte hardware sectors (125 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 45 00 00 08
> sd 0:0:0:0: [sda] Assuming drive cache: write through
> sd 0:0:0:0: [sda] 244735 512-byte hardware sectors (125 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 45 00 00 08
> sd 0:0:0:0: [sda] Assuming drive cache: write through
> sda: sda1
> sd 0:0:0:0: [sda] Attached SCSI removable disk
> sd 0:0:0:0: Attached scsi generic sg0 type 0
> usb-storage: device scan complete
> irq 25: nobody cared (try booting with the "irqpoll" option)
> Call Trace:
> [cf135af0] [c0008820] show_stack+0x48/0x190 (unreliable)
> [cf135b20] [c003c414] __report_bad_irq+0x34/0xac
> [cf135b40] [c003c714] note_interrupt+0x288/0x2c8
> [cf135b70] [c003b818] __do_IRQ+0x104/0x110
> [cf135b90] [c0006900] do_IRQ+0xbc/0xc0
> [cf135ba0] [c00020c0] ret_from_except+0x0/0x18
> [cf135c60] [00000019] 0x19
> [cf135c90] [c000668c] do_softirq+0x54/0x58
> [cf135ca0] [c001df40] irq_exit+0x48/0x58
> [cf135cb0] [c00068b4] do_IRQ+0x70/0xc0
> [cf135cc0] [c00020c0] ret_from_except+0x0/0x18
> [cf135d80] [c003c2b4] setup_irq+0x1ac/0x200
> [cf135da0] [c003c3cc] request_irq+0xc4/0xd8
> [cf135dd0] [c0122328] rtl8139_open+0x38/0x210
> [cf135df0] [c0187500] dev_open+0x7c/0xcc
> [cf135e10] [c0187420] dev_change_flags+0x16c/0x1d0
> [cf135e30] [c01cbff0] devinet_ioctl+0x604/0x720
> [cf135ea0] [c01cc1f8] inet_ioctl+0x98/0xbc
> [cf135eb0] [c0179328] sock_ioctl+0x60/0x260
> [cf135ed0] [c006c360] do_ioctl+0x38/0x84
> [cf135ee0] [c006c438] vfs_ioctl+0x8c/0x40c
> [cf135f10] [c006c7f8] sys_ioctl+0x40/0x74
> [cf135f40] [c0001a84] ret_from_syscall+0x0/0x3c
> handlers:
> [<c0122bd4>] (rtl8139_interrupt+0x0/0x52c)
> Disabling IRQ #25
> eth2: link up, 100Mbps, full-duplex, lpa 0x45E1
>
>
> Who can give some advice?
>
> Thanks.
> BRs,
> Andrew.
>
>
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-dev
Looks like wrong external interrupt settings (trigger/level) for PCI
interrupt.
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: AMCC yosemite 440ep PCI slot doesn't work.
2007-09-21 15:14 ` Valentine Barshak
@ 2007-09-24 9:34 ` Andrew Liu
2007-09-24 11:14 ` Stefan Roese
0 siblings, 1 reply; 9+ messages in thread
From: Andrew Liu @ 2007-09-24 9:34 UTC (permalink / raw)
To: Valentine Barshak; +Cc: linuxppc-dev
By default, it is IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE
I change it to IRQ_SENSE_EDGE | IRQ_POLARITY_NEGATIVE or
IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE.
It displays:
eth2: link up, 100Mbps, full-duplex, lpa 0x45E1
eth2: no IPv6 routers present
NETDEV WATCHDOG: eth2: transmit timed out
eth2: Transmit timeout, status 0c 0005 c07f media 10.
eth2: Tx queue start entry 4 dirty entry 0.
eth2: Tx descriptor 0 is 0008a05a. (queue head)
eth2: Tx descriptor 1 is 0008a04e.
eth2: Tx descriptor 2 is 0008a046.
eth2: Tx descriptor 3 is 0008a05a.
eth2: link up, 100Mbps, full-duplex, lpa 0x45E1
and
root@localhost:/root> ifconfig eth2
eth2 Link encap:Ethernet HWaddr 00:0E:2E:7E:F5:E6
inet addr:128.224.149.13 Bcast:128.224.255.255 Mask:255.255.0.0
inet6 addr: fe80::20e:2eff:fe7e:f5e6/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:25 Base address:0x6f00
and
root@localhost:/root> cat /proc/interrupts
CPU0
2: 0 UIC0 Edge IBM IIC
7: 0 UIC0 Edge IBM IIC
10: 11961 UIC0 Edge MAL TX EOB
11: 18471 UIC0 Edge MAL RX EOB
25: 0 UIC0 Edge eth2
32: 0 UIC1 Edge MAL SERR
33: 0 UIC1 Edge MAL TX DE
34: 0 UIC1 Edge MAL RX DE
40: 32 UIC1 Edge ohci_hcd:usb1
60: 0 UIC1 Edge EMAC
BAD: 0
Can PCI slot use level trigger?
give me some advice.
Thanks.
Valentine Barshak wrote:
> Andrew Liu wrote:
>> Hello All,
>>
>> when insert a RealTek RTL8139 network card into PCI slot,
>> After system boot up,
>>
>> root@localhost:/root> ifconfig eth2 192.168.17.12
>> irq 25: nobody cared (try booting with the "irqpoll" option)
>> Call Trace:
>> [cf135af0] [c0008820] show_stack+0x48/0x190 (unreliable)
>> [cf135b20] [c003c414] __report_bad_irq+0x34/0xac
>> [cf135b40] [c003c714] note_interrupt+0x288/0x2c8
>> [cf135b70] [c003b818] __do_IRQ+0x104/0x110
>> [cf135b90] [c0006900] do_IRQ+0xbc/0xc0
>> [cf135ba0] [c00020c0] ret_from_except+0x0/0x18
>> [cf135c60] [00000019] 0x19
>> [cf135c90] [c000668c] do_softirq+0x54/0x58
>> [cf135ca0] [c001df40] irq_exit+0x48/0x58
>> [cf135cb0] [c00068b4] do_IRQ+0x70/0xc0
>> [cf135cc0] [c00020c0] ret_from_except+0x0/0x18
>> [cf135d80] [c003c2b4] setup_irq+0x1ac/0x200
>> [cf135da0] [c003c3cc] request_irq+0xc4/0xd8
>> [cf135dd0] [c0122328] rtl8139_open+0x38/0x210
>> [cf135df0] [c0187500] dev_open+0x7c/0xcc
>> [cf135e10] [c0187420] dev_change_flags+0x16c/0x1d0
>> [cf135e30] [c01cbff0] devinet_ioctl+0x604/0x720
>> [cf135ea0] [c01cc1f8] inet_ioctl+0x98/0xbc
>> [cf135eb0] [c0179328] sock_ioctl+0x60/0x260
>> [cf135ed0] [c006c360] do_ioctl+0x38/0x84
>> [cf135ee0] [c006c438] vfs_ioctl+0x8c/0x40c
>> [cf135f10] [c006c7f8] sys_ioctl+0x40/0x74
>> [cf135f40] [c0001a84] ret_from_syscall+0x0/0x3c
>> handlers:
>> [<c0122bd4>] (rtl8139_interrupt+0x0/0x52c)
>> Disabling IRQ #25
>> root@localhost:/root>
>> Message from syslogd@localhost at Thu Jan 1 00:02:13 1970 ...
>> localhost kernel: Disabling IRQ #25
>>
>> root@localhost:/root>
>>
>>
>> The system boot up information as follows:
>> root@localhost:/root> dmesg
>> Linux version 2.6.23-rc6-gea60adb5 (sliu@localhost.localdomain) (gcc
>> version 4.0.0 (DENX ELDK 4.1 4.0.0)) #3 Fri Sep 21 18:37:59 CST 2007
>> AMCC PowerPC 440EP Yosemite Platform
>> Entering add_active_range(0, 0, 65536) 0 entries of 256 used
>> Zone PFN ranges:
>> DMA 0 -> 65536
>> Normal 65536 -> 65536
>> Movable zone start PFN for each node
>> early_node_map[1] active PFN ranges
>> 0: 0 -> 65536
>> On node 0 totalpages: 65536
>> DMA zone: 512 pages used for memmap
>> DMA zone: 0 pages reserved
>> DMA zone: 65024 pages, LIFO batch:15
>> Normal zone: 0 pages used for memmap
>> Movable zone: 0 pages used for memmap
>> Built 1 zonelists in Zone order. Total pages: 65024
>> Kernel command line: root=/dev/nfs rw
>> nfsroot=128.224.149.6:/tftpboot/sliu/rootfs
>> ip=128.224.149.11::128.224.149.1:255.255.255.0:yosemite:eth0:off
>> console=ttyS0,9600
>> PID hash table entries: 1024 (order: 10, 4096 bytes)
>> console [ttyS0] enabled
>> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
>> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
>> Memory: 256896k available (2052k kernel code, 716k data, 152k init, 0k
>> highmem)
>> Calibrating delay loop... 798.72 BogoMIPS (lpj=1597440)
>> Mount-cache hash table entries: 512
>> NET: Registered protocol family 16
>> PCI: Probing PCI hardware
>> PCI: Scanning bus 0000:00
>> PCI: Found 0000:00:0c.0 [10ec/8139] 000200 00
>> PCI: Calling quirk c000444c for 0000:00:0c.0
>> PCI: Fixups for bus 0000:00
>> PCI: Bus scan for 0000:00 returning with max=00
>> PCI: fixup irq: (0000:00:0c.0) got 25
>> SCSI subsystem initialized
>> usbcore: registered new interface driver usbfs
>> usbcore: registered new interface driver hub
>> usbcore: registered new device driver usb
>> NET: Registered protocol family 2
>> IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
>> TCP established hash table entries: 8192 (order: 4, 65536 bytes)
>> TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
>> TCP: Hash tables configured (established 8192 bind 8192)
>> TCP reno registered
>> io scheduler noop registered
>> io scheduler anticipatory registered (default)
>> io scheduler deadline registered
>> io scheduler cfq registered
>> PCI: Calling quirk c00fbab4 for 0000:00:0c.0
>> PCI: Calling quirk c02ae3b8 for 0000:00:0c.0
>> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
>> serial8250: ttyS0 at MMIO 0x0 (irq = 0) is a 16550A
>> serial8250: ttyS1 at MMIO 0x0 (irq = 1) is a 16550A
>> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
>> PPC 4xx OCP EMAC driver, version 3.54
>> mal0: initialized, 4 TX channels, 2 RX channels
>> zmii0: bridge in RMII mode
>> eth0: emac0, MAC 00:10:ec:00:87:42
>> eth0: found Generic MII PHY (0x01)
>> eth1: emac1, MAC 00:00:00:00:00:00
>> eth1: found Generic MII PHY (0x03)
>> 8139too Fast Ethernet driver 0.9.28
>> eth2: RealTek RTL8139 at 0xd1012f00, 00:0e:2e:7e:f5:e6, IRQ 25
>> eth2: Identified 8139 chip type 'RTL-8100B/8139D'
>> pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
>> usbcore: registered new interface driver pegasus
>> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
>> ide: Assuming 33MHz system bus speed for PIO modes; override with
>> idebus=xx
>> usbmon: debugfs is not available
>> ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
>> ppc-soc-ohci ppc-soc-ohci.0: USB Host Controller
>> ppc-soc-ohci ppc-soc-ohci.0: new USB bus registered, assigned bus
>> number 1
>> ppc-soc-ohci ppc-soc-ohci.0: irq 40, io mem 0xef601000
>> usb usb1: configuration #1 chosen from 1 choice
>> hub 1-0:1.0: USB hub found
>> hub 1-0:1.0: 2 ports detected
>> Initializing USB Mass Storage driver...
>> usbcore: registered new interface driver usb-storage
>> USB Mass Storage support registered.
>> ether gadget: using random self ethernet address
>> ether gadget: using random host ethernet address
>> usb0: Ethernet Gadget, version: May Day 2005
>> usb0: using musbhsfc_udc, OUT ep2 IN ep1 STATUS ep3
>> usb0: MAC 66:91:74:ab:fb:61
>> usb0: HOST MAC 1a:b5:87:5d:8f:00
>> usb0: RNDIS ready
>> musbhsfc_udc: registered gadget driver 'ether'
>> TCP cubic registered
>> NET: Registered protocol family 1
>> NET: Registered protocol family 17
>> usb 1-1: new full speed USB device using ppc-soc-ohci and address 2
>> usb 1-1: configuration #1 chosen from 1 choice
>> eth0: link is up, 100 FDX, pause enabled
>> scsi0 : SCSI emulation for USB Mass Storage devices
>> usb-storage: device found at 2
>> usb-storage: waiting for device to settle before scanning
>> IP-Config: Complete:
>> device=eth0, addr=128.224.149.11, mask=255.255.255.0,
>> gw=128.224.149.1,
>> host=yosemite, domain=, nis-domain=(none),
>> bootserver=255.255.255.255, rootserver=128.224.149.6, rootpath=
>> Looking up port of RPC 100003/2 on 128.224.149.6
>> Looking up port of RPC 100005/1 on 128.224.149.6
>> VFS: Mounted root (nfs filesystem).
>> Freeing unused kernel memory: 152k init
>> scsi 0:0:0:0: Direct-Access Kingston DataTraveler 2.0 6.16 PQ: 0
>> ANSI: 0 CCS
>> sd 0:0:0:0: [sda] 244735 512-byte hardware sectors (125 MB)
>> sd 0:0:0:0: [sda] Write Protect is off
>> sd 0:0:0:0: [sda] Mode Sense: 45 00 00 08
>> sd 0:0:0:0: [sda] Assuming drive cache: write through
>> sd 0:0:0:0: [sda] 244735 512-byte hardware sectors (125 MB)
>> sd 0:0:0:0: [sda] Write Protect is off
>> sd 0:0:0:0: [sda] Mode Sense: 45 00 00 08
>> sd 0:0:0:0: [sda] Assuming drive cache: write through
>> sda: sda1
>> sd 0:0:0:0: [sda] Attached SCSI removable disk
>> sd 0:0:0:0: Attached scsi generic sg0 type 0
>> usb-storage: device scan complete
>> irq 25: nobody cared (try booting with the "irqpoll" option)
>> Call Trace:
>> [cf135af0] [c0008820] show_stack+0x48/0x190 (unreliable)
>> [cf135b20] [c003c414] __report_bad_irq+0x34/0xac
>> [cf135b40] [c003c714] note_interrupt+0x288/0x2c8
>> [cf135b70] [c003b818] __do_IRQ+0x104/0x110
>> [cf135b90] [c0006900] do_IRQ+0xbc/0xc0
>> [cf135ba0] [c00020c0] ret_from_except+0x0/0x18
>> [cf135c60] [00000019] 0x19
>> [cf135c90] [c000668c] do_softirq+0x54/0x58
>> [cf135ca0] [c001df40] irq_exit+0x48/0x58
>> [cf135cb0] [c00068b4] do_IRQ+0x70/0xc0
>> [cf135cc0] [c00020c0] ret_from_except+0x0/0x18
>> [cf135d80] [c003c2b4] setup_irq+0x1ac/0x200
>> [cf135da0] [c003c3cc] request_irq+0xc4/0xd8
>> [cf135dd0] [c0122328] rtl8139_open+0x38/0x210
>> [cf135df0] [c0187500] dev_open+0x7c/0xcc
>> [cf135e10] [c0187420] dev_change_flags+0x16c/0x1d0
>> [cf135e30] [c01cbff0] devinet_ioctl+0x604/0x720
>> [cf135ea0] [c01cc1f8] inet_ioctl+0x98/0xbc
>> [cf135eb0] [c0179328] sock_ioctl+0x60/0x260
>> [cf135ed0] [c006c360] do_ioctl+0x38/0x84
>> [cf135ee0] [c006c438] vfs_ioctl+0x8c/0x40c
>> [cf135f10] [c006c7f8] sys_ioctl+0x40/0x74
>> [cf135f40] [c0001a84] ret_from_syscall+0x0/0x3c
>> handlers:
>> [<c0122bd4>] (rtl8139_interrupt+0x0/0x52c)
>> Disabling IRQ #25
>> eth2: link up, 100Mbps, full-duplex, lpa 0x45E1
>>
>>
>> Who can give some advice?
>>
>> Thanks.
>> BRs,
>> Andrew.
>>
>>
>> _______________________________________________
>> Linuxppc-dev mailing list
>> Linuxppc-dev@ozlabs.org
>> https://ozlabs.org/mailman/listinfo/linuxppc-dev
>
> Looks like wrong external interrupt settings (trigger/level) for PCI
> interrupt.
>
^ permalink raw reply [flat|nested] 9+ messages in thread* Re: AMCC yosemite 440ep PCI slot doesn't work.
2007-09-24 9:34 ` Andrew Liu
@ 2007-09-24 11:14 ` Stefan Roese
2007-09-24 11:20 ` Valentine Barshak
2007-09-25 2:02 ` Andrew Liu
0 siblings, 2 replies; 9+ messages in thread
From: Stefan Roese @ 2007-09-24 11:14 UTC (permalink / raw)
To: linuxppc-dev
On Monday 24 September 2007, Andrew Liu wrote:
> By default, it is IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE
And that should be correct for PCI interrupts.
> I change it to IRQ_SENSE_EDGE | IRQ_POLARITY_NEGATIVE or
> IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE.
> It displays:
> eth2: link up, 100Mbps, full-duplex, lpa 0x45E1
> eth2: no IPv6 routers present
> NETDEV WATCHDOG: eth2: transmit timed out
> eth2: Transmit timeout, status 0c 0005 c07f media 10.
> eth2: Tx queue start entry 4 dirty entry 0.
> eth2: Tx descriptor 0 is 0008a05a. (queue head)
> eth2: Tx descriptor 1 is 0008a04e.
> eth2: Tx descriptor 2 is 0008a046.
> eth2: Tx descriptor 3 is 0008a05a.
> eth2: link up, 100Mbps, full-duplex, lpa 0x45E1
>
> and
> root@localhost:/root> ifconfig eth2
> eth2 Link encap:Ethernet HWaddr 00:0E:2E:7E:F5:E6
> inet addr:128.224.149.13 Bcast:128.224.255.255 Mask:255.255.0.0
> inet6 addr: fe80::20e:2eff:fe7e:f5e6/64 Scope:Link
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
> Interrupt:25 Base address:0x6f00
>
>
> and
> root@localhost:/root> cat /proc/interrupts
> CPU0
> 2: 0 UIC0 Edge IBM IIC
> 7: 0 UIC0 Edge IBM IIC
> 10: 11961 UIC0 Edge MAL TX EOB
> 11: 18471 UIC0 Edge MAL RX EOB
> 25: 0 UIC0 Edge eth2
> 32: 0 UIC1 Edge MAL SERR
> 33: 0 UIC1 Edge MAL TX DE
> 34: 0 UIC1 Edge MAL RX DE
> 40: 32 UIC1 Edge ohci_hcd:usb1
> 60: 0 UIC1 Edge EMAC
> BAD: 0
>
>
> Can PCI slot use level trigger?
>
> give me some advice.
Hmmm. Did you try an earlier Linux version too? For example 2.6.22 or even
earlier? Please give it a try and let us know if the same problem occurs.
Best regards,
Stefan
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: AMCC yosemite 440ep PCI slot doesn't work.
2007-09-24 11:14 ` Stefan Roese
@ 2007-09-24 11:20 ` Valentine Barshak
2007-09-25 2:05 ` Andrew Liu
2007-09-25 2:02 ` Andrew Liu
1 sibling, 1 reply; 9+ messages in thread
From: Valentine Barshak @ 2007-09-24 11:20 UTC (permalink / raw)
To: Stefan Roese; +Cc: linuxppc-dev
Stefan Roese wrote:
> On Monday 24 September 2007, Andrew Liu wrote:
>> By default, it is IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE
>
> And that should be correct for PCI interrupts.
>
>> I change it to IRQ_SENSE_EDGE | IRQ_POLARITY_NEGATIVE or
>> IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE.
>> It displays:
>> eth2: link up, 100Mbps, full-duplex, lpa 0x45E1
>> eth2: no IPv6 routers present
>> NETDEV WATCHDOG: eth2: transmit timed out
>> eth2: Transmit timeout, status 0c 0005 c07f media 10.
>> eth2: Tx queue start entry 4 dirty entry 0.
>> eth2: Tx descriptor 0 is 0008a05a. (queue head)
>> eth2: Tx descriptor 1 is 0008a04e.
>> eth2: Tx descriptor 2 is 0008a046.
>> eth2: Tx descriptor 3 is 0008a05a.
>> eth2: link up, 100Mbps, full-duplex, lpa 0x45E1
>>
>> and
>> root@localhost:/root> ifconfig eth2
>> eth2 Link encap:Ethernet HWaddr 00:0E:2E:7E:F5:E6
>> inet addr:128.224.149.13 Bcast:128.224.255.255 Mask:255.255.0.0
>> inet6 addr: fe80::20e:2eff:fe7e:f5e6/64 Scope:Link
>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>> collisions:0 txqueuelen:1000
>> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
>> Interrupt:25 Base address:0x6f00
>>
>>
>> and
>> root@localhost:/root> cat /proc/interrupts
>> CPU0
>> 2: 0 UIC0 Edge IBM IIC
>> 7: 0 UIC0 Edge IBM IIC
>> 10: 11961 UIC0 Edge MAL TX EOB
>> 11: 18471 UIC0 Edge MAL RX EOB
>> 25: 0 UIC0 Edge eth2
>> 32: 0 UIC1 Edge MAL SERR
>> 33: 0 UIC1 Edge MAL TX DE
>> 34: 0 UIC1 Edge MAL RX DE
>> 40: 32 UIC1 Edge ohci_hcd:usb1
>> 60: 0 UIC1 Edge EMAC
>> BAD: 0
>>
>>
>> Can PCI slot use level trigger?
>>
>> give me some advice.
This could be caused by misseting the IRQ_lEVEL flag in desc->status.
There have been a commit 4dc7b4b0405fd7320940849b6e31ea8ea68fd0df that
fixes the problem.
Thanks,
Valentine.
>
> Hmmm. Did you try an earlier Linux version too? For example 2.6.22 or even
> earlier? Please give it a try and let us know if the same problem occurs.
>
> Best regards,
> Stefan
>
> =====================================================================
> DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de
> =====================================================================
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: AMCC yosemite 440ep PCI slot doesn't work.
2007-09-24 11:20 ` Valentine Barshak
@ 2007-09-25 2:05 ` Andrew Liu
0 siblings, 0 replies; 9+ messages in thread
From: Andrew Liu @ 2007-09-25 2:05 UTC (permalink / raw)
To: Valentine Barshak; +Cc: linuxppc-dev, Stefan Roese
Currently, ppc44x use ppc branch, not powerpc, especially for AMCC
yosemite 440ep.
Through adding printk in function ppc4xx_pic_init which is in
arch/ppc/syslib/ppc4xx_pic.c, whether setting IRQ_LEVEL has no effect
on it.
BRs,
Andrew
Valentine Barshak wrote:
> Stefan Roese wrote:
>> On Monday 24 September 2007, Andrew Liu wrote:
>>> By default, it is IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE
>>
>> And that should be correct for PCI interrupts.
>>
>>> I change it to IRQ_SENSE_EDGE | IRQ_POLARITY_NEGATIVE or
>>> IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE.
>>> It displays:
>>> eth2: link up, 100Mbps, full-duplex, lpa 0x45E1
>>> eth2: no IPv6 routers present
>>> NETDEV WATCHDOG: eth2: transmit timed out
>>> eth2: Transmit timeout, status 0c 0005 c07f media 10.
>>> eth2: Tx queue start entry 4 dirty entry 0.
>>> eth2: Tx descriptor 0 is 0008a05a. (queue head)
>>> eth2: Tx descriptor 1 is 0008a04e.
>>> eth2: Tx descriptor 2 is 0008a046.
>>> eth2: Tx descriptor 3 is 0008a05a.
>>> eth2: link up, 100Mbps, full-duplex, lpa 0x45E1
>>>
>>> and
>>> root@localhost:/root> ifconfig eth2
>>> eth2 Link encap:Ethernet HWaddr 00:0E:2E:7E:F5:E6
>>> inet addr:128.224.149.13 Bcast:128.224.255.255
>>> Mask:255.255.0.0
>>> inet6 addr: fe80::20e:2eff:fe7e:f5e6/64 Scope:Link
>>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>> collisions:0 txqueuelen:1000
>>> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
>>> Interrupt:25 Base address:0x6f00
>>>
>>>
>>> and
>>> root@localhost:/root> cat /proc/interrupts
>>> CPU0
>>> 2: 0 UIC0 Edge IBM IIC
>>> 7: 0 UIC0 Edge IBM IIC
>>> 10: 11961 UIC0 Edge MAL TX EOB
>>> 11: 18471 UIC0 Edge MAL RX EOB
>>> 25: 0 UIC0 Edge eth2
>>> 32: 0 UIC1 Edge MAL SERR
>>> 33: 0 UIC1 Edge MAL TX DE
>>> 34: 0 UIC1 Edge MAL RX DE
>>> 40: 32 UIC1 Edge ohci_hcd:usb1
>>> 60: 0 UIC1 Edge EMAC
>>> BAD: 0
>>>
>>>
>>> Can PCI slot use level trigger?
>>>
>>> give me some advice.
>
> This could be caused by misseting the IRQ_lEVEL flag in desc->status.
> There have been a commit 4dc7b4b0405fd7320940849b6e31ea8ea68fd0df that
> fixes the problem.
> Thanks,
> Valentine.
>
>>
>> Hmmm. Did you try an earlier Linux version too? For example 2.6.22 or
>> even earlier? Please give it a try and let us know if the same
>> problem occurs.
>>
>> Best regards,
>> Stefan
>>
>> =====================================================================
>> DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
>> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
>> Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de
>> =====================================================================
>
>
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: AMCC yosemite 440ep PCI slot doesn't work.
2007-09-24 11:14 ` Stefan Roese
2007-09-24 11:20 ` Valentine Barshak
@ 2007-09-25 2:02 ` Andrew Liu
2007-09-25 5:18 ` Stefan Roese
1 sibling, 1 reply; 9+ messages in thread
From: Andrew Liu @ 2007-09-25 2:02 UTC (permalink / raw)
To: Stefan Roese; +Cc: linuxppc-dev
I have tested it on linux-2.6.19 which is from AMCC website , linux
2.6.21.7 which is from linux mainline and linux-2.6.23.rc7 which is
from git://www.denx.de/git/linux-2.6-denx.git
Have the same problem.
I don't understand, why after enabling this PCI interrupts. in so
short time, produce 100,000 interrupt request (25: 100000 UIC0
Level eth2).
BRs,
Andrew.
Stefan Roese wrote:
> On Monday 24 September 2007, Andrew Liu wrote:
>
>> By default, it is IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE
>>
>
> And that should be correct for PCI interrupts.
>
>
>> I change it to IRQ_SENSE_EDGE | IRQ_POLARITY_NEGATIVE or
>> IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE.
>> It displays:
>> eth2: link up, 100Mbps, full-duplex, lpa 0x45E1
>> eth2: no IPv6 routers present
>> NETDEV WATCHDOG: eth2: transmit timed out
>> eth2: Transmit timeout, status 0c 0005 c07f media 10.
>> eth2: Tx queue start entry 4 dirty entry 0.
>> eth2: Tx descriptor 0 is 0008a05a. (queue head)
>> eth2: Tx descriptor 1 is 0008a04e.
>> eth2: Tx descriptor 2 is 0008a046.
>> eth2: Tx descriptor 3 is 0008a05a.
>> eth2: link up, 100Mbps, full-duplex, lpa 0x45E1
>>
>> and
>> root@localhost:/root> ifconfig eth2
>> eth2 Link encap:Ethernet HWaddr 00:0E:2E:7E:F5:E6
>> inet addr:128.224.149.13 Bcast:128.224.255.255 Mask:255.255.0.0
>> inet6 addr: fe80::20e:2eff:fe7e:f5e6/64 Scope:Link
>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>> collisions:0 txqueuelen:1000
>> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
>> Interrupt:25 Base address:0x6f00
>>
>>
>> and
>> root@localhost:/root> cat /proc/interrupts
>> CPU0
>> 2: 0 UIC0 Edge IBM IIC
>> 7: 0 UIC0 Edge IBM IIC
>> 10: 11961 UIC0 Edge MAL TX EOB
>> 11: 18471 UIC0 Edge MAL RX EOB
>> 25: 0 UIC0 Edge eth2
>> 32: 0 UIC1 Edge MAL SERR
>> 33: 0 UIC1 Edge MAL TX DE
>> 34: 0 UIC1 Edge MAL RX DE
>> 40: 32 UIC1 Edge ohci_hcd:usb1
>> 60: 0 UIC1 Edge EMAC
>> BAD: 0
>>
>>
>> Can PCI slot use level trigger?
>>
>> give me some advice.
>>
>
> Hmmm. Did you try an earlier Linux version too? For example 2.6.22 or even
> earlier? Please give it a try and let us know if the same problem occurs.
>
> Best regards,
> Stefan
>
> =====================================================================
> DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de
> =====================================================================
>
>
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: AMCC yosemite 440ep PCI slot doesn't work.
2007-09-25 2:02 ` Andrew Liu
@ 2007-09-25 5:18 ` Stefan Roese
2007-09-25 13:21 ` Stefan Roese
0 siblings, 1 reply; 9+ messages in thread
From: Stefan Roese @ 2007-09-25 5:18 UTC (permalink / raw)
To: linuxppc-dev
On Tuesday 25 September 2007, Andrew Liu wrote:
> I have tested it on linux-2.6.19 which is from AMCC website , linux
> 2.6.21.7 which is from linux mainline and linux-2.6.23.rc7 which is
> from git://www.denx.de/git/linux-2.6-denx.git
> Have the same problem.
> I don't understand, why after enabling this PCI interrupts. in so
> short time, produce 100,000 interrupt request (25: 100000 UIC0
> Level eth2).
Because the interrupt is somehow not acknowledged in the PCI device.
I will test this on my Yosemite and let you know.
Best regards,
Stefan
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: AMCC yosemite 440ep PCI slot doesn't work.
2007-09-25 5:18 ` Stefan Roese
@ 2007-09-25 13:21 ` Stefan Roese
0 siblings, 0 replies; 9+ messages in thread
From: Stefan Roese @ 2007-09-25 13:21 UTC (permalink / raw)
To: linuxppc-dev
On Tuesday 25 September 2007, Stefan Roese wrote:
> On Tuesday 25 September 2007, Andrew Liu wrote:
> > I have tested it on linux-2.6.19 which is from AMCC website , linux
> > 2.6.21.7 which is from linux mainline and linux-2.6.23.rc7 which is
> > from git://www.denx.de/git/linux-2.6-denx.git
> > Have the same problem.
> > I don't understand, why after enabling this PCI interrupts. in so
> > short time, produce 100,000 interrupt request (25: 100000 UIC0
> > Level eth2).
>
> Because the interrupt is somehow not acknowledged in the PCI device.
>
> I will test this on my Yosemite and let you know.
I just tested on my Yellowstone, which is nearly identical to the Yosemite.
And it works just fine with an Intel EEPRO/100.
Could you test another PCI board (ethernet, IDE, USB...)? Or do you have
access to another Yosemite or Yellowstone board?
Best regards,
Stefan
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2007-09-25 13:20 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2007-09-21 10:53 AMCC yosemite 440ep PCI slot doesn't work Andrew Liu
2007-09-21 15:14 ` Valentine Barshak
2007-09-24 9:34 ` Andrew Liu
2007-09-24 11:14 ` Stefan Roese
2007-09-24 11:20 ` Valentine Barshak
2007-09-25 2:05 ` Andrew Liu
2007-09-25 2:02 ` Andrew Liu
2007-09-25 5:18 ` Stefan Roese
2007-09-25 13:21 ` Stefan Roese
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).