* need help with GPIO
@ 2008-09-02 1:21 Laxmikant Rashinkar
2008-09-02 6:39 ` Marco Stornelli
0 siblings, 1 reply; 4+ messages in thread
From: Laxmikant Rashinkar @ 2008-09-02 1:21 UTC (permalink / raw)
To: linuxppc-embedded
[-- Attachment #1: Type: text/plain, Size: 19781 bytes --]
Hi,
I have a MPC8347 based embedded PC running Linux 2.6.27.
I am trying to access a NAND device connected to the LBC and UPM.
The Ready/Busy* pin of the NAND device is connected to the built in GPIO-1 on pin 4 (input).
When I try to access the NAND device, the function of_get_gpio() from drivers/of/gpio.c gets called, and
it reports that my GPIO is not registered. Here are the actual debug messages:
LK_DEBUG: gpio.c : of_get_gpio : name=upm type=<NULL> index=0
LK_DEBUG: gpio.c : of_get_gpio : got property
LK_DEBUG: gpio.c : of_get_gpio : nr_cell=3
LK_DEBUG: gpio.c : of_get_gpio : gc.name=gpio-controller gc.type=<NULL> gc->Data=0x0
LK_DEBUG: gpio.c : of_get_gpio : /localbus/upm@1,0: gpio controller /soc8349@e0000000/gpio-controller@e0000c00: is not registered
When I check in /proc/device-tree/soc8349@e0000000/, I find that entries are present for both GPIOs are present.
Here are debug registration messages, indicating that gpio registered successfully:
##### LK_DEBUG: of_plat_dev_create : NAME=soc8349
##### LK_DEBUG: of_plat_dev_create : NAME=wdt
##### LK_DEBUG: of_plat_dev_create : NAME=i2c
##### LK_DEBUG: of_plat_dev_create : NAME=i2c
##### LK_DEBUG: of_plat_dev_create : NAME=spi
##### LK_DEBUG: of_plat_dev_create : NAME=dma
##### LK_DEBUG: of_plat_dev_create : NAME=usb
##### LK_DEBUG: of_plat_dev_create : NAME=usb
##### LK_DEBUG: of_plat_dev_create : NAME=mdio
##### LK_DEBUG: of_plat_dev_create : NAME=ethernet
##### LK_DEBUG: of_plat_dev_create : NAME=ethernet
##### LK_DEBUG: of_plat_dev_create : NAME=serial
##### LK_DEBUG: of_plat_dev_create : NAME=serial
##### LK_DEBUG: of_plat_dev_create : NAME=crypto
##### LK_DEBUG: of_plat_dev_create : NAME=pic
##### LK_DEBUG: of_plat_dev_create : NAME=gpio-controller
##### LK_DEBUG: of_plat_dev_create : NAME=gpio-controller
##### LK_DEBUG: of_plat_dev_create : NAME=localbus
##### LK_DEBUG: of_plat_dev_create : NAME=upm
Most probably something is wrong in my device tree (listed below). Can someone please point me in the right direction?
thanks a lot for your help.
LK
-------------------------------------------------------------
/*
* MPC8349E MDS Device Tree Source
*
* Copyright 2005, 2006 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
/dts-v1/;
/ {
model = "MPC8349EMDS";
compatible = "MPC8349EMDS", "MPC834xMDS", "MPC83xxMDS";
#address-cells = <1>;
#size-cells = <1>;
aliases {
ethernet0 = &enet0;
ethernet1 = &enet1;
serial0 = &serial0;
serial1 = &serial1;
pci0 = &pci0;
pci1 = &pci1;
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
PowerPC,8349@0 {
device_type = "cpu";
reg = <0x0>;
d-cache-line-size = <32>;
i-cache-line-size = <32>;
d-cache-size = <32768>;
i-cache-size = <32768>;
timebase-frequency = <0>; // from bootloader
bus-frequency = <0>; // from bootloader
clock-frequency = <0>; // from bootloader
};
};
memory {
device_type = "memory";
reg = <0x00000000 0x10000000>; // 256MB at 0
};
bcsr@e2400000 {
device_type = "board-control";
reg = <0xe2400000 0x8000>;
};
soc8349@e0000000 {
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
compatible = "simple-bus";
ranges = <0x0 0xe0000000 0x00100000>;
reg = <0xe0000000 0x00000200>;
bus-frequency = <0>;
wdt@200 {
device_type = "watchdog";
compatible = "mpc83xx_wdt";
reg = <0x200 0x100>;
};
i2c@3000 {
#address-cells = <1>;
#size-cells = <0>;
cell-index = <0>;
compatible = "fsl-i2c";
reg = <0x3000 0x100>;
interrupts = <14 0x8>;
interrupt-parent = <&ipic>;
dfsrr;
rtc@68 {
compatible = "dallas,ds1374";
reg = <0x68>;
};
};
i2c@3100 {
#address-cells = <1>;
#size-cells = <0>;
cell-index = <1>;
compatible = "fsl-i2c";
reg = <0x3100 0x100>;
interrupts = <15 0x8>;
interrupt-parent = <&ipic>;
dfsrr;
};
spi@7000 {
cell-index = <0>;
compatible = "fsl,spi";
reg = <0x7000 0x1000>;
interrupts = <16 0x8>;
interrupt-parent = <&ipic>;
mode = "cpu";
};
dma@82a8 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,mpc8349-dma", "fsl,elo-dma";
reg = <0x82a8 4>;
ranges = <0 0x8100 0x1a8>;
interrupt-parent = <&ipic>;
interrupts = <71 8>;
cell-index = <0>;
dma-channel@0 {
compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
reg = <0 0x80>;
interrupt-parent = <&ipic>;
interrupts = <71 8>;
};
dma-channel@80 {
compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
reg = <0x80 0x80>;
interrupt-parent = <&ipic>;
interrupts = <71 8>;
};
dma-channel@100 {
compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
reg = <0x100 0x80>;
interrupt-parent = <&ipic>;
interrupts = <71 8>;
};
dma-channel@180 {
compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
reg = <0x180 0x28>;
interrupt-parent = <&ipic>;
interrupts = <71 8>;
};
};
/* phy type (ULPI or SERIAL) are only types supported for MPH */
/* port = 0 or 1 */
usb@22000 {
compatible = "fsl-usb2-mph";
reg = <0x22000 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
interrupt-parent = <&ipic>;
interrupts = <39 0x8>;
phy_type = "ulpi";
port1;
};
/* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
usb@23000 {
compatible = "fsl-usb2-dr";
reg = <0x23000 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
interrupt-parent = <&ipic>;
interrupts = <38 0x8>;
dr_mode = "otg";
phy_type = "ulpi";
};
mdio@24520 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,gianfar-mdio";
reg = <0x24520 0x20>;
phy0: ethernet-phy@0 {
interrupt-parent = <&ipic>;
interrupts = <17 0x8>;
reg = <0x1>;
device_type = "ethernet-phy";
};
phy1: ethernet-phy@1 {
interrupt-parent = <&ipic>;
interrupts = <18 0x8>;
reg = <0x2>;
device_type = "ethernet-phy";
};
};
enet0: ethernet@24000 {
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
interrupt-parent = <&ipic>;
phy-handle = <&phy0>;
linux,network-index = <0>;
};
enet1: ethernet@25000 {
cell-index = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
interrupt-parent = <&ipic>;
phy-handle = <&phy1>;
linux,network-index = <1>;
};
serial0: serial@4500 {
cell-index = <0>;
device_type = "serial";
compatible = "ns16550";
reg = <0x4500 0x100>;
clock-frequency = <0>;
interrupts = <9 0x8>;
interrupt-parent = <&ipic>;
};
serial1: serial@4600 {
cell-index = <1>;
device_type = "serial";
compatible = "ns16550";
reg = <0x4600 0x100>;
clock-frequency = <0>;
interrupts = <10 0x8>;
interrupt-parent = <&ipic>;
};
crypto@30000 {
compatible = "fsl,sec2.0";
reg = <0x30000 0x10000>;
interrupts = <11 0x8>;
interrupt-parent = <&ipic>;
fsl,num-channels = <4>;
fsl,channel-fifo-len = <24>;
fsl,exec-units-mask = <0x7e>;
fsl,descriptor-types-mask = <0x01010ebf>;
};
/* IPIC
* interrupts cell = <intr #, sense>
* sense values match linux IORESOURCE_IRQ_* defines:
* sense == 8: Level, low assertion
* sense == 2: Edge, high-to-low change
*/
ipic: pic@700 {
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <2>;
reg = <0x700 0x100>;
device_type = "ipic";
};
gpio1: gpio-controller@e0000c00 {
#gpio-cells = <2>;
compatible = "fsl,mpc8349-gpio-bank";
reg = <0xe0000c00 0x100>;
gpio-controller;
};
gpio2: gpio-controller@e0000d00 {
#gpio-cells = <2>;
compatible = "fsl,mpc8349-gpio-bank";
reg = <0xe0000d00 0x100>;
gpio-controller;
};
};
localbus {
compatible = "fsl,pq3-localbus", "simple-bus";
#address-cells = <2>;
#size-cells = <1>;
reg = <0xe0005000 0x100000>; // BRx, ORx, etc.
upm@1,0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,upm-nand";
reg = <3 0xa0000000 0x800>;
fsl,upm-addr-offset = <0x10>;
fsl,upm-cmd-offset = <0x08>;
gpios = <&gpio1 4 0>;
nand@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,lbc-nand";
partition@0 {
label = "EVERYTHING";
reg = <0x00000000 0x01000000>;
};
};
};
};
pci0: pci@e0008500 {
cell-index = <1>;
interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x11 */
0x8800 0x0 0x0 0x1 &ipic 20 0x8
0x8800 0x0 0x0 0x2 &ipic 21 0x8
0x8800 0x0 0x0 0x3 &ipic 22 0x8
0x8800 0x0 0x0 0x4 &ipic 23 0x8
/* IDSEL 0x12 */
0x9000 0x0 0x0 0x1 &ipic 22 0x8
0x9000 0x0 0x0 0x2 &ipic 23 0x8
0x9000 0x0 0x0 0x3 &ipic 20 0x8
0x9000 0x0 0x0 0x4 &ipic 21 0x8
/* IDSEL 0x13 */
0x9800 0x0 0x0 0x1 &ipic 23 0x8
0x9800 0x0 0x0 0x2 &ipic 20 0x8
0x9800 0x0 0x0 0x3 &ipic 21 0x8
0x9800 0x0 0x0 0x4 &ipic 22 0x8
/* IDSEL 0x15 */
0xa800 0x0 0x0 0x1 &ipic 20 0x8
0xa800 0x0 0x0 0x2 &ipic 21 0x8
0xa800 0x0 0x0 0x3 &ipic 22 0x8
0xa800 0x0 0x0 0x4 &ipic 23 0x8
/* IDSEL 0x16 */
0xb000 0x0 0x0 0x1 &ipic 23 0x8
0xb000 0x0 0x0 0x2 &ipic 20 0x8
0xb000 0x0 0x0 0x3 &ipic 21 0x8
0xb000 0x0 0x0 0x4 &ipic 22 0x8
/* IDSEL 0x17 */
0xb800 0x0 0x0 0x1 &ipic 22 0x8
0xb800 0x0 0x0 0x2 &ipic 23 0x8
0xb800 0x0 0x0 0x3 &ipic 20 0x8
0xb800 0x0 0x0 0x4 &ipic 21 0x8
/* IDSEL 0x18 */
0xc000 0x0 0x0 0x1 &ipic 21 0x8
0xc000 0x0 0x0 0x2 &ipic 22 0x8
0xc000 0x0 0x0 0x3 &ipic 23 0x8
0xc000 0x0 0x0 0x4 &ipic 20 0x8>;
interrupt-parent = <&ipic>;
interrupts = <66 0x8>;
bus-range = <0 0>;
ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
clock-frequency = <66666666>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
reg = <0xe0008500 0x100>;
compatible = "fsl,mpc8349-pci";
device_type = "pci";
};
pci1: pci@e0008600 {
cell-index = <2>;
interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x11 */
0x8800 0x0 0x0 0x1 &ipic 20 0x8
0x8800 0x0 0x0 0x2 &ipic 21 0x8
0x8800 0x0 0x0 0x3 &ipic 22 0x8
0x8800 0x0 0x0 0x4 &ipic 23 0x8
/* IDSEL 0x12 */
0x9000 0x0 0x0 0x1 &ipic 22 0x8
0x9000 0x0 0x0 0x2 &ipic 23 0x8
0x9000 0x0 0x0 0x3 &ipic 20 0x8
0x9000 0x0 0x0 0x4 &ipic 21 0x8
/* IDSEL 0x13 */
0x9800 0x0 0x0 0x1 &ipic 23 0x8
0x9800 0x0 0x0 0x2 &ipic 20 0x8
0x9800 0x0 0x0 0x3 &ipic 21 0x8
0x9800 0x0 0x0 0x4 &ipic 22 0x8
/* IDSEL 0x15 */
0xa800 0x0 0x0 0x1 &ipic 20 0x8
0xa800 0x0 0x0 0x2 &ipic 21 0x8
0xa800 0x0 0x0 0x3 &ipic 22 0x8
0xa800 0x0 0x0 0x4 &ipic 23 0x8
/* IDSEL 0x16 */
0xb000 0x0 0x0 0x1 &ipic 23 0x8
0xb000 0x0 0x0 0x2 &ipic 20 0x8
0xb000 0x0 0x0 0x3 &ipic 21 0x8
0xb000 0x0 0x0 0x4 &ipic 22 0x8
/* IDSEL 0x17 */
0xb800 0x0 0x0 0x1 &ipic 22 0x8
0xb800 0x0 0x0 0x2 &ipic 23 0x8
0xb800 0x0 0x0 0x3 &ipic 20 0x8
0xb800 0x0 0x0 0x4 &ipic 21 0x8
/* IDSEL 0x18 */
0xc000 0x0 0x0 0x1 &ipic 21 0x8
0xc000 0x0 0x0 0x2 &ipic 22 0x8
0xc000 0x0 0x0 0x3 &ipic 23 0x8
0xc000 0x0 0x0 0x4 &ipic 20 0x8>;
interrupt-parent = <&ipic>;
interrupts = <67 0x8>;
bus-range = <0 0>;
ranges = <0x02000000 0x0 0xb0000000 0xb0000000 0x0 0x10000000
0x42000000 0x0 0xa0000000 0xa0000000 0x0 0x10000000
0x01000000 0x0 0x00000000 0xe2100000 0x0 0x00100000>;
clock-frequency = <66666666>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
reg = <0xe0008600 0x100>;
compatible = "fsl,mpc8349-pci";
device_type = "pci";
};
chosen {
linux,stdout-path = &serial0;
};
};
[-- Attachment #2: Type: text/html, Size: 63955 bytes --]
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: need help with GPIO
2008-09-02 1:21 need help with GPIO Laxmikant Rashinkar
@ 2008-09-02 6:39 ` Marco Stornelli
0 siblings, 0 replies; 4+ messages in thread
From: Marco Stornelli @ 2008-09-02 6:39 UTC (permalink / raw)
To: Laxmikant Rashinkar; +Cc: linuxppc-embedded
Laxmikant Rashinkar ha scritto:
> Hi,
>
> I have a MPC8347 based embedded PC running Linux 2.6.27.
> I am trying to access a NAND device connected to the LBC and UPM.
> The Ready/Busy* pin of the NAND device is connected to the built in GPIO-1 on pin 4 (input).
>
> When I try to access the NAND device, the function of_get_gpio() from drivers/of/gpio.c gets called, and
> it reports that my GPIO is not registered. Here are the actual debug messages:
>
> LK_DEBUG: gpio.c : of_get_gpio : name=upm type=<NULL> index=0
> LK_DEBUG: gpio.c : of_get_gpio : got property
> LK_DEBUG: gpio.c : of_get_gpio : nr_cell=3
> LK_DEBUG: gpio.c : of_get_gpio : gc.name=gpio-controller gc.type=<NULL> gc->Data=0x0
> LK_DEBUG: gpio.c : of_get_gpio : /localbus/upm@1,0: gpio controller /soc8349@e0000000/gpio-controller@e0000c00: is not registered
>
> When I check in /proc/device-tree/soc8349@e0000000/, I find that entries are present for both GPIOs are present.
>
> Here are debug registration messages, indicating that gpio registered successfully:
>
> ##### LK_DEBUG: of_plat_dev_create : NAME=soc8349
> ##### LK_DEBUG: of_plat_dev_create : NAME=wdt
> ##### LK_DEBUG: of_plat_dev_create : NAME=i2c
> ##### LK_DEBUG: of_plat_dev_create : NAME=i2c
> ##### LK_DEBUG: of_plat_dev_create : NAME=spi
> ##### LK_DEBUG: of_plat_dev_create : NAME=dma
> ##### LK_DEBUG: of_plat_dev_create : NAME=usb
> ##### LK_DEBUG: of_plat_dev_create : NAME=usb
> ##### LK_DEBUG: of_plat_dev_create : NAME=mdio
> ##### LK_DEBUG: of_plat_dev_create : NAME=ethernet
> ##### LK_DEBUG: of_plat_dev_create : NAME=ethernet
> ##### LK_DEBUG: of_plat_dev_create : NAME=serial
> ##### LK_DEBUG: of_plat_dev_create : NAME=serial
> ##### LK_DEBUG: of_plat_dev_create : NAME=crypto
> ##### LK_DEBUG: of_plat_dev_create : NAME=pic
> ##### LK_DEBUG: of_plat_dev_create : NAME=gpio-controller
> ##### LK_DEBUG: of_plat_dev_create : NAME=gpio-controller
> ##### LK_DEBUG: of_plat_dev_create : NAME=localbus
> ##### LK_DEBUG: of_plat_dev_create : NAME=upm
>
> Most probably something is wrong in my device tree (listed below). Can someone please point me in the right direction?
>
> thanks a lot for your help.
> LK
>
> -------------------------------------------------------------
>
> /*
> * MPC8349E MDS Device Tree Source
> *
> * Copyright 2005, 2006 Freescale Semiconductor Inc.
> *
> * This program is free software; you can redistribute it and/or modify it
> * under the terms of the GNU General Public License as published by the
> * Free Software Foundation; either version 2 of the License, or (at your
> * option) any later version.
> */
>
> /dts-v1/;
>
> / {
> model = "MPC8349EMDS";
> compatible = "MPC8349EMDS", "MPC834xMDS", "MPC83xxMDS";
> #address-cells = <1>;
> #size-cells = <1>;
>
> aliases {
> ethernet0 = &enet0;
> ethernet1 = &enet1;
> serial0 = &serial0;
> serial1 = &serial1;
> pci0 = &pci0;
> pci1 = &pci1;
> };
>
> cpus {
> #address-cells = <1>;
> #size-cells = <0>;
>
> PowerPC,8349@0 {
> device_type = "cpu";
> reg = <0x0>;
> d-cache-line-size = <32>;
> i-cache-line-size = <32>;
> d-cache-size = <32768>;
> i-cache-size = <32768>;
> timebase-frequency = <0>; // from bootloader
> bus-frequency = <0>; // from bootloader
> clock-frequency = <0>; // from bootloader
> };
> };
>
> memory {
> device_type = "memory";
> reg = <0x00000000 0x10000000>; // 256MB at 0
> };
>
> bcsr@e2400000 {
> device_type = "board-control";
> reg = <0xe2400000 0x8000>;
> };
>
> soc8349@e0000000 {
> #address-cells = <1>;
> #size-cells = <1>;
> device_type = "soc";
> compatible = "simple-bus";
> ranges = <0x0 0xe0000000 0x00100000>;
> reg = <0xe0000000 0x00000200>;
> bus-frequency = <0>;
>
> wdt@200 {
> device_type = "watchdog";
> compatible = "mpc83xx_wdt";
> reg = <0x200 0x100>;
> };
>
> i2c@3000 {
> #address-cells = <1>;
> #size-cells = <0>;
> cell-index = <0>;
> compatible = "fsl-i2c";
> reg = <0x3000 0x100>;
> interrupts = <14 0x8>;
> interrupt-parent = <&ipic>;
> dfsrr;
>
> rtc@68 {
> compatible = "dallas,ds1374";
> reg = <0x68>;
> };
> };
>
> i2c@3100 {
> #address-cells = <1>;
> #size-cells = <0>;
> cell-index = <1>;
> compatible = "fsl-i2c";
> reg = <0x3100 0x100>;
> interrupts = <15 0x8>;
> interrupt-parent = <&ipic>;
> dfsrr;
> };
>
> spi@7000 {
> cell-index = <0>;
> compatible = "fsl,spi";
> reg = <0x7000 0x1000>;
> interrupts = <16 0x8>;
> interrupt-parent = <&ipic>;
> mode = "cpu";
> };
>
> dma@82a8 {
> #address-cells = <1>;
> #size-cells = <1>;
> compatible = "fsl,mpc8349-dma", "fsl,elo-dma";
> reg = <0x82a8 4>;
> ranges = <0 0x8100 0x1a8>;
> interrupt-parent = <&ipic>;
> interrupts = <71 8>;
> cell-index = <0>;
> dma-channel@0 {
> compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
> reg = <0 0x80>;
> interrupt-parent = <&ipic>;
> interrupts = <71 8>;
> };
> dma-channel@80 {
> compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
> reg = <0x80 0x80>;
> interrupt-parent = <&ipic>;
> interrupts = <71 8>;
> };
> dma-channel@100 {
> compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
> reg = <0x100 0x80>;
> interrupt-parent = <&ipic>;
> interrupts = <71 8>;
> };
> dma-channel@180 {
> compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
> reg = <0x180 0x28>;
> interrupt-parent = <&ipic>;
> interrupts = <71 8>;
> };
> };
>
> /* phy type (ULPI or SERIAL) are only types supported for MPH */
> /* port = 0 or 1 */
> usb@22000 {
> compatible = "fsl-usb2-mph";
> reg = <0x22000 0x1000>;
> #address-cells = <1>;
> #size-cells = <0>;
> interrupt-parent = <&ipic>;
> interrupts = <39 0x8>;
> phy_type = "ulpi";
> port1;
> };
> /* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
> usb@23000 {
> compatible = "fsl-usb2-dr";
> reg = <0x23000 0x1000>;
> #address-cells = <1>;
> #size-cells = <0>;
> interrupt-parent = <&ipic>;
> interrupts = <38 0x8>;
> dr_mode = "otg";
> phy_type = "ulpi";
> };
>
> mdio@24520 {
> #address-cells = <1>;
> #size-cells = <0>;
> compatible = "fsl,gianfar-mdio";
> reg = <0x24520 0x20>;
>
> phy0: ethernet-phy@0 {
> interrupt-parent = <&ipic>;
> interrupts = <17 0x8>;
> reg = <0x1>;
> device_type = "ethernet-phy";
> };
> phy1: ethernet-phy@1 {
> interrupt-parent = <&ipic>;
> interrupts = <18 0x8>;
> reg = <0x2>;
> device_type = "ethernet-phy";
> };
> };
>
> enet0: ethernet@24000 {
> cell-index = <0>;
> device_type = "network";
> model = "TSEC";
> compatible = "gianfar";
> reg = <0x24000 0x1000>;
> local-mac-address = [ 00 00 00 00 00 00 ];
> interrupts = <32 0x8 33 0x8 34 0x8>;
> interrupt-parent = <&ipic>;
> phy-handle = <&phy0>;
> linux,network-index = <0>;
> };
>
> enet1: ethernet@25000 {
> cell-index = <1>;
> device_type = "network";
> model = "TSEC";
> compatible = "gianfar";
> reg = <0x25000 0x1000>;
> local-mac-address = [ 00 00 00 00 00 00 ];
> interrupts = <35 0x8 36 0x8 37 0x8>;
> interrupt-parent = <&ipic>;
> phy-handle = <&phy1>;
> linux,network-index = <1>;
> };
>
> serial0: serial@4500 {
> cell-index = <0>;
> device_type = "serial";
> compatible = "ns16550";
> reg = <0x4500 0x100>;
> clock-frequency = <0>;
> interrupts = <9 0x8>;
> interrupt-parent = <&ipic>;
> };
>
> serial1: serial@4600 {
> cell-index = <1>;
> device_type = "serial";
> compatible = "ns16550";
> reg = <0x4600 0x100>;
> clock-frequency = <0>;
> interrupts = <10 0x8>;
> interrupt-parent = <&ipic>;
> };
>
> crypto@30000 {
> compatible = "fsl,sec2.0";
> reg = <0x30000 0x10000>;
> interrupts = <11 0x8>;
> interrupt-parent = <&ipic>;
> fsl,num-channels = <4>;
> fsl,channel-fifo-len = <24>;
> fsl,exec-units-mask = <0x7e>;
> fsl,descriptor-types-mask = <0x01010ebf>;
> };
>
> /* IPIC
> * interrupts cell = <intr #, sense>
> * sense values match linux IORESOURCE_IRQ_* defines:
> * sense == 8: Level, low assertion
> * sense == 2: Edge, high-to-low change
> */
> ipic: pic@700 {
> interrupt-controller;
> #address-cells = <0>;
> #interrupt-cells = <2>;
> reg = <0x700 0x100>;
> device_type = "ipic";
> };
>
Here you are using absolute addresses but you should use an offset from
a base reg address, in your case e0000000.
> gpio1: gpio-controller@e0000c00 {
gpio1: gpio-controller@c00 {
> #gpio-cells = <2>;
> compatible = "fsl,mpc8349-gpio-bank";
reg = <0xc00 0x100>;
> reg = <0xe0000c00 0x100>;
> gpio-controller;
> };
>
gpio2: gpio-controller@d00 {
> gpio2: gpio-controller@e0000d00 {
> #gpio-cells = <2>;
> compatible = "fsl,mpc8349-gpio-bank";
reg = <0xd00 0x100>;
> reg = <0xe0000d00 0x100>;
> gpio-controller;
> };
> };
>
> localbus {
> compatible = "fsl,pq3-localbus", "simple-bus";
> #address-cells = <2>;
> #size-cells = <1>;
> reg = <0xe0005000 0x100000>; // BRx, ORx, etc.
>
> upm@1,0 {
> #address-cells = <1>;
> #size-cells = <1>;
> compatible = "fsl,upm-nand";
> reg = <3 0xa0000000 0x800>;
> fsl,upm-addr-offset = <0x10>;
> fsl,upm-cmd-offset = <0x08>;
> gpios = <&gpio1 4 0>;
>
> nand@0 {
> #address-cells = <1>;
> #size-cells = <1>;
> compatible = "fsl,lbc-nand";
>
> partition@0 {
> label = "EVERYTHING";
> reg = <0x00000000 0x01000000>;
> };
> };
> };
> };
>
> pci0: pci@e0008500 {
> cell-index = <1>;
> interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
> interrupt-map = <
>
> /* IDSEL 0x11 */
> 0x8800 0x0 0x0 0x1 &ipic 20 0x8
> 0x8800 0x0 0x0 0x2 &ipic 21 0x8
> 0x8800 0x0 0x0 0x3 &ipic 22 0x8
> 0x8800 0x0 0x0 0x4 &ipic 23 0x8
>
> /* IDSEL 0x12 */
> 0x9000 0x0 0x0 0x1 &ipic 22 0x8
> 0x9000 0x0 0x0 0x2 &ipic 23 0x8
> 0x9000 0x0 0x0 0x3 &ipic 20 0x8
> 0x9000 0x0 0x0 0x4 &ipic 21 0x8
>
> /* IDSEL 0x13 */
> 0x9800 0x0 0x0 0x1 &ipic 23 0x8
> 0x9800 0x0 0x0 0x2 &ipic 20 0x8
> 0x9800 0x0 0x0 0x3 &ipic 21 0x8
> 0x9800 0x0 0x0 0x4 &ipic 22 0x8
>
> /* IDSEL 0x15 */
> 0xa800 0x0 0x0 0x1 &ipic 20 0x8
> 0xa800 0x0 0x0 0x2 &ipic 21 0x8
> 0xa800 0x0 0x0 0x3 &ipic 22 0x8
> 0xa800 0x0 0x0 0x4 &ipic 23 0x8
>
> /* IDSEL 0x16 */
> 0xb000 0x0 0x0 0x1 &ipic 23 0x8
> 0xb000 0x0 0x0 0x2 &ipic 20 0x8
> 0xb000 0x0 0x0 0x3 &ipic 21 0x8
> 0xb000 0x0 0x0 0x4 &ipic 22 0x8
>
> /* IDSEL 0x17 */
> 0xb800 0x0 0x0 0x1 &ipic 22 0x8
> 0xb800 0x0 0x0 0x2 &ipic 23 0x8
> 0xb800 0x0 0x0 0x3 &ipic 20 0x8
> 0xb800 0x0 0x0 0x4 &ipic 21 0x8
>
> /* IDSEL 0x18 */
> 0xc000 0x0 0x0 0x1 &ipic 21 0x8
> 0xc000 0x0 0x0 0x2 &ipic 22 0x8
> 0xc000 0x0 0x0 0x3 &ipic 23 0x8
> 0xc000 0x0 0x0 0x4 &ipic 20 0x8>;
> interrupt-parent = <&ipic>;
> interrupts = <66 0x8>;
> bus-range = <0 0>;
> ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
> 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
> 0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
> clock-frequency = <66666666>;
> #interrupt-cells = <1>;
> #size-cells = <2>;
> #address-cells = <3>;
> reg = <0xe0008500 0x100>;
> compatible = "fsl,mpc8349-pci";
> device_type = "pci";
> };
>
> pci1: pci@e0008600 {
> cell-index = <2>;
> interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
> interrupt-map = <
>
> /* IDSEL 0x11 */
> 0x8800 0x0 0x0 0x1 &ipic 20 0x8
> 0x8800 0x0 0x0 0x2 &ipic 21 0x8
> 0x8800 0x0 0x0 0x3 &ipic 22 0x8
> 0x8800 0x0 0x0 0x4 &ipic 23 0x8
>
> /* IDSEL 0x12 */
> 0x9000 0x0 0x0 0x1 &ipic 22 0x8
> 0x9000 0x0 0x0 0x2 &ipic 23 0x8
> 0x9000 0x0 0x0 0x3 &ipic 20 0x8
> 0x9000 0x0 0x0 0x4 &ipic 21 0x8
>
> /* IDSEL 0x13 */
> 0x9800 0x0 0x0 0x1 &ipic 23 0x8
> 0x9800 0x0 0x0 0x2 &ipic 20 0x8
> 0x9800 0x0 0x0 0x3 &ipic 21 0x8
> 0x9800 0x0 0x0 0x4 &ipic 22 0x8
>
> /* IDSEL 0x15 */
> 0xa800 0x0 0x0 0x1 &ipic 20 0x8
> 0xa800 0x0 0x0 0x2 &ipic 21 0x8
> 0xa800 0x0 0x0 0x3 &ipic 22 0x8
> 0xa800 0x0 0x0 0x4 &ipic 23 0x8
>
> /* IDSEL 0x16 */
> 0xb000 0x0 0x0 0x1 &ipic 23 0x8
> 0xb000 0x0 0x0 0x2 &ipic 20 0x8
> 0xb000 0x0 0x0 0x3 &ipic 21 0x8
> 0xb000 0x0 0x0 0x4 &ipic 22 0x8
>
> /* IDSEL 0x17 */
> 0xb800 0x0 0x0 0x1 &ipic 22 0x8
> 0xb800 0x0 0x0 0x2 &ipic 23 0x8
> 0xb800 0x0 0x0 0x3 &ipic 20 0x8
> 0xb800 0x0 0x0 0x4 &ipic 21 0x8
>
> /* IDSEL 0x18 */
> 0xc000 0x0 0x0 0x1 &ipic 21 0x8
> 0xc000 0x0 0x0 0x2 &ipic 22 0x8
> 0xc000 0x0 0x0 0x3 &ipic 23 0x8
> 0xc000 0x0 0x0 0x4 &ipic 20 0x8>;
> interrupt-parent = <&ipic>;
> interrupts = <67 0x8>;
> bus-range = <0 0>;
> ranges = <0x02000000 0x0 0xb0000000 0xb0000000 0x0 0x10000000
> 0x42000000 0x0 0xa0000000 0xa0000000 0x0 0x10000000
> 0x01000000 0x0 0x00000000 0xe2100000 0x0 0x00100000>;
> clock-frequency = <66666666>;
> #interrupt-cells = <1>;
> #size-cells = <2>;
> #address-cells = <3>;
> reg = <0xe0008600 0x100>;
> compatible = "fsl,mpc8349-pci";
> device_type = "pci";
> };
>
> chosen {
> linux,stdout-path = &serial0;
> };
> };
>
>
>
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
--
Marco Stornelli
Embedded Software Engineer
CoRiTeL - Consorzio di Ricerca sulle Telecomunicazioni
http://www.coritel.it
marco.stornelli@coritel.it
+39 06 72582838
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: need help with GPIO
@ 2008-09-02 16:59 Laxmikant Rashinkar
2008-09-03 6:37 ` Marco Stornelli
0 siblings, 1 reply; 4+ messages in thread
From: Laxmikant Rashinkar @ 2008-09-02 16:59 UTC (permalink / raw)
To: Marco Stornelli; +Cc: linuxppc-embedded
[-- Attachment #1: Type: text/plain, Size: 22071 bytes --]
Hi Marco,
thanks for your feedback.
I tried out your suggestion of using an offset address instead of an absolute address in the dts, but that did not help.
I am still getting the error:
LK_DEBUG: gpio.c : of_get_gpio : /localbus/upm@1,0: gpio controller /soc8349@e0000000/gpio-controller@c00: is not registered
thanks
LK
----- Original Message ----
From: Marco Stornelli <marco.stornelli@coritel.it>
To: Laxmikant Rashinkar <lk.atwork@yahoo.com>
Cc: linuxppc-embedded@ozlabs.org
Sent: Monday, September 1, 2008 11:39:05 PM
Subject: Re: need help with GPIO
Laxmikant Rashinkar ha scritto:
> Hi,
>
> I have a MPC8347 based embedded PC running Linux 2.6.27.
> I am trying to access a NAND device connected to the LBC and UPM.
> The Ready/Busy* pin of the NAND device is connected to the built in GPIO-1 on pin 4 (input).
>
> When I try to access the NAND device, the function of_get_gpio() from drivers/of/gpio.c gets called, and
> it reports that my GPIO is not registered. Here are the actual debug messages:
>
> LK_DEBUG: gpio.c : of_get_gpio : name=upm type=<NULL> index=0
> LK_DEBUG: gpio.c : of_get_gpio : got property
> LK_DEBUG: gpio.c : of_get_gpio : nr_cell=3
> LK_DEBUG: gpio.c : of_get_gpio : gc.name=gpio-controller gc.type=<NULL> gc->Data=0x0
> LK_DEBUG: gpio.c : of_get_gpio : /localbus/upm@1,0: gpio controller /soc8349@e0000000/gpio-controller@e0000c00: is not registered
>
> When I check in /proc/device-tree/soc8349@e0000000/, I find that entries are present for both GPIOs are present.
>
> Here are debug registration messages, indicating that gpio registered successfully:
>
> ##### LK_DEBUG: of_plat_dev_create : NAME=soc8349
> ##### LK_DEBUG: of_plat_dev_create : NAME=wdt
> ##### LK_DEBUG: of_plat_dev_create : NAME=i2c
> ##### LK_DEBUG: of_plat_dev_create : NAME=i2c
> ##### LK_DEBUG: of_plat_dev_create : NAME=spi
> ##### LK_DEBUG: of_plat_dev_create : NAME=dma
> ##### LK_DEBUG: of_plat_dev_create : NAME=usb
> ##### LK_DEBUG: of_plat_dev_create : NAME=usb
> ##### LK_DEBUG: of_plat_dev_create : NAME=mdio
> ##### LK_DEBUG: of_plat_dev_create : NAME=ethernet
> ##### LK_DEBUG: of_plat_dev_create : NAME=ethernet
> ##### LK_DEBUG: of_plat_dev_create : NAME=serial
> ##### LK_DEBUG: of_plat_dev_create : NAME=serial
> ##### LK_DEBUG: of_plat_dev_create : NAME=crypto
> ##### LK_DEBUG: of_plat_dev_create : NAME=pic
> ##### LK_DEBUG: of_plat_dev_create : NAME=gpio-controller
> ##### LK_DEBUG: of_plat_dev_create : NAME=gpio-controller
> ##### LK_DEBUG: of_plat_dev_create : NAME=localbus
> ##### LK_DEBUG: of_plat_dev_create : NAME=upm
>
> Most probably something is wrong in my device tree (listed below). Can someone please point me in the right direction?
>
> thanks a lot for your help.
> LK
>
> -------------------------------------------------------------
>
> /*
> * MPC8349E MDS Device Tree Source
> *
> * Copyright 2005, 2006 Freescale Semiconductor Inc.
> *
> * This program is free software; you can redistribute it and/or modify it
> * under the terms of the GNU General Public License as published by the
> * Free Software Foundation; either version 2 of the License, or (at your
> * option) any later version.
> */
>
> /dts-v1/;
>
> / {
> model = "MPC8349EMDS";
> compatible = "MPC8349EMDS", "MPC834xMDS", "MPC83xxMDS";
> #address-cells = <1>;
> #size-cells = <1>;
>
> aliases {
> ethernet0 = &enet0;
> ethernet1 = &enet1;
> serial0 = &serial0;
> serial1 = &serial1;
> pci0 = &pci0;
> pci1 = &pci1;
> };
>
> cpus {
> #address-cells = <1>;
> #size-cells = <0>;
>
> PowerPC,8349@0 {
> device_type = "cpu";
> reg = <0x0>;
> d-cache-line-size = <32>;
> i-cache-line-size = <32>;
> d-cache-size = <32768>;
> i-cache-size = <32768>;
> timebase-frequency = <0>; // from bootloader
> bus-frequency = <0>; // from bootloader
> clock-frequency = <0>; // from bootloader
> };
> };
>
> memory {
> device_type = "memory";
> reg = <0x00000000 0x10000000>; // 256MB at 0
> };
>
> bcsr@e2400000 {
> device_type = "board-control";
> reg = <0xe2400000 0x8000>;
> };
>
> soc8349@e0000000 {
> #address-cells = <1>;
> #size-cells = <1>;
> device_type = "soc";
> compatible = "simple-bus";
> ranges = <0x0 0xe0000000 0x00100000>;
> reg = <0xe0000000 0x00000200>;
> bus-frequency = <0>;
>
> wdt@200 {
> device_type = "watchdog";
> compatible = "mpc83xx_wdt";
> reg = <0x200 0x100>;
> };
>
> i2c@3000 {
> #address-cells = <1>;
> #size-cells = <0>;
> cell-index = <0>;
> compatible = "fsl-i2c";
> reg = <0x3000 0x100>;
> interrupts = <14 0x8>;
> interrupt-parent = <&ipic>;
> dfsrr;
>
> rtc@68 {
> compatible = "dallas,ds1374";
> reg = <0x68>;
> };
> };
>
> i2c@3100 {
> #address-cells = <1>;
> #size-cells = <0>;
> cell-index = <1>;
> compatible = "fsl-i2c";
> reg = <0x3100 0x100>;
> interrupts = <15 0x8>;
> interrupt-parent = <&ipic>;
> dfsrr;
> };
>
> spi@7000 {
> cell-index = <0>;
> compatible = "fsl,spi";
> reg = <0x7000 0x1000>;
> interrupts = <16 0x8>;
> interrupt-parent = <&ipic>;
> mode = "cpu";
> };
>
> dma@82a8 {
> #address-cells = <1>;
> #size-cells = <1>;
> compatible = "fsl,mpc8349-dma", "fsl,elo-dma";
> reg = <0x82a8 4>;
> ranges = <0 0x8100 0x1a8>;
> interrupt-parent = <&ipic>;
> interrupts = <71 8>;
> cell-index = <0>;
> dma-channel@0 {
> compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
> reg = <0 0x80>;
> interrupt-parent = <&ipic>;
> interrupts = <71 8>;
> };
> dma-channel@80 {
> compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
> reg = <0x80 0x80>;
> interrupt-parent = <&ipic>;
> interrupts = <71 8>;
> };
> dma-channel@100 {
> compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
> reg = <0x100 0x80>;
> interrupt-parent = <&ipic>;
> interrupts = <71 8>;
> };
> dma-channel@180 {
> compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
> reg = <0x180 0x28>;
> interrupt-parent = <&ipic>;
> interrupts = <71 8>;
> };
> };
>
> /* phy type (ULPI or SERIAL) are only types supported for MPH */
> /* port = 0 or 1 */
> usb@22000 {
> compatible = "fsl-usb2-mph";
> reg = <0x22000 0x1000>;
> #address-cells = <1>;
> #size-cells = <0>;
> interrupt-parent = <&ipic>;
> interrupts = <39 0x8>;
> phy_type = "ulpi";
> port1;
> };
> /* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
> usb@23000 {
> compatible = "fsl-usb2-dr";
> reg = <0x23000 0x1000>;
> #address-cells = <1>;
> #size-cells = <0>;
> interrupt-parent = <&ipic>;
> interrupts = <38 0x8>;
> dr_mode = "otg";
> phy_type = "ulpi";
> };
>
> mdio@24520 {
> #address-cells = <1>;
> #size-cells = <0>;
> compatible = "fsl,gianfar-mdio";
> reg = <0x24520 0x20>;
>
> phy0: ethernet-phy@0 {
> interrupt-parent = <&ipic>;
> interrupts = <17 0x8>;
> reg = <0x1>;
> device_type = "ethernet-phy";
> };
> phy1: ethernet-phy@1 {
> interrupt-parent = <&ipic>;
> interrupts = <18 0x8>;
> reg = <0x2>;
> device_type = "ethernet-phy";
> };
> };
>
> enet0: ethernet@24000 {
> cell-index = <0>;
> device_type = "network";
> model = "TSEC";
> compatible = "gianfar";
> reg = <0x24000 0x1000>;
> local-mac-address = [ 00 00 00 00 00 00 ];
> interrupts = <32 0x8 33 0x8 34 0x8>;
> interrupt-parent = <&ipic>;
> phy-handle = <&phy0>;
> linux,network-index = <0>;
> };
>
> enet1: ethernet@25000 {
> cell-index = <1>;
> device_type = "network";
> model = "TSEC";
> compatible = "gianfar";
> reg = <0x25000 0x1000>;
> local-mac-address = [ 00 00 00 00 00 00 ];
> interrupts = <35 0x8 36 0x8 37 0x8>;
> interrupt-parent = <&ipic>;
> phy-handle = <&phy1>;
> linux,network-index = <1>;
> };
>
> serial0: serial@4500 {
> cell-index = <0>;
> device_type = "serial";
> compatible = "ns16550";
> reg = <0x4500 0x100>;
> clock-frequency = <0>;
> interrupts = <9 0x8>;
> interrupt-parent = <&ipic>;
> };
>
> serial1: serial@4600 {
> cell-index = <1>;
> device_type = "serial";
> compatible = "ns16550";
> reg = <0x4600 0x100>;
> clock-frequency = <0>;
> interrupts = <10 0x8>;
> interrupt-parent = <&ipic>;
> };
>
> crypto@30000 {
> compatible = "fsl,sec2.0";
> reg = <0x30000 0x10000>;
> interrupts = <11 0x8>;
> interrupt-parent = <&ipic>;
> fsl,num-channels = <4>;
> fsl,channel-fifo-len = <24>;
> fsl,exec-units-mask = <0x7e>;
> fsl,descriptor-types-mask = <0x01010ebf>;
> };
>
> /* IPIC
> * interrupts cell = <intr #, sense>
> * sense values match linux IORESOURCE_IRQ_* defines:
> * sense == 8: Level, low assertion
> * sense == 2: Edge, high-to-low change
> */
> ipic: pic@700 {
> interrupt-controller;
> #address-cells = <0>;
> #interrupt-cells = <2>;
> reg = <0x700 0x100>;
> device_type = "ipic";
> };
>
Here you are using absolute addresses but you should use an offset from
a base reg address, in your case e0000000.
> gpio1: gpio-controller@e0000c00 {
gpio1: gpio-controller@c00 {
> #gpio-cells = <2>;
> compatible = "fsl,mpc8349-gpio-bank";
reg = <0xc00 0x100>;
> reg = <0xe0000c00 0x100>;
> gpio-controller;
> };
>
gpio2: gpio-controller@d00 {
> gpio2: gpio-controller@e0000d00 {
> #gpio-cells = <2>;
> compatible = "fsl,mpc8349-gpio-bank";
reg = <0xd00 0x100>;
> reg = <0xe0000d00 0x100>;
> gpio-controller;
> };
> };
>
> localbus {
> compatible = "fsl,pq3-localbus", "simple-bus";
> #address-cells = <2>;
> #size-cells = <1>;
> reg = <0xe0005000 0x100000>; // BRx, ORx, etc.
>
> upm@1,0 {
> #address-cells = <1>;
> #size-cells = <1>;
> compatible = "fsl,upm-nand";
> reg = <3 0xa0000000 0x800>;
> fsl,upm-addr-offset = <0x10>;
> fsl,upm-cmd-offset = <0x08>;
> gpios = <&gpio1 4 0>;
>
> nand@0 {
> #address-cells = <1>;
> #size-cells = <1>;
> compatible = "fsl,lbc-nand";
>
> partition@0 {
> label = "EVERYTHING";
> reg = <0x00000000 0x01000000>;
> };
> };
> };
> };
>
> pci0: pci@e0008500 {
> cell-index = <1>;
> interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
> interrupt-map = <
>
> /* IDSEL 0x11 */
> 0x8800 0x0 0x0 0x1 &ipic 20 0x8
> 0x8800 0x0 0x0 0x2 &ipic 21 0x8
> 0x8800 0x0 0x0 0x3 &ipic 22 0x8
> 0x8800 0x0 0x0 0x4 &ipic 23 0x8
>
> /* IDSEL 0x12 */
> 0x9000 0x0 0x0 0x1 &ipic 22 0x8
> 0x9000 0x0 0x0 0x2 &ipic 23 0x8
> 0x9000 0x0 0x0 0x3 &ipic 20 0x8
> 0x9000 0x0 0x0 0x4 &ipic 21 0x8
>
> /* IDSEL 0x13 */
> 0x9800 0x0 0x0 0x1 &ipic 23 0x8
> 0x9800 0x0 0x0 0x2 &ipic 20 0x8
> 0x9800 0x0 0x0 0x3 &ipic 21 0x8
> 0x9800 0x0 0x0 0x4 &ipic 22 0x8
>
> /* IDSEL 0x15 */
> 0xa800 0x0 0x0 0x1 &ipic 20 0x8
> 0xa800 0x0 0x0 0x2 &ipic 21 0x8
> 0xa800 0x0 0x0 0x3 &ipic 22 0x8
> 0xa800 0x0 0x0 0x4 &ipic 23 0x8
>
> /* IDSEL 0x16 */
> 0xb000 0x0 0x0 0x1 &ipic 23 0x8
> 0xb000 0x0 0x0 0x2 &ipic 20 0x8
> 0xb000 0x0 0x0 0x3 &ipic 21 0x8
> 0xb000 0x0 0x0 0x4 &ipic 22 0x8
>
> /* IDSEL 0x17 */
> 0xb800 0x0 0x0 0x1 &ipic 22 0x8
> 0xb800 0x0 0x0 0x2 &ipic 23 0x8
> 0xb800 0x0 0x0 0x3 &ipic 20 0x8
> 0xb800 0x0 0x0 0x4 &ipic 21 0x8
>
> /* IDSEL 0x18 */
> 0xc000 0x0 0x0 0x1 &ipic 21 0x8
> 0xc000 0x0 0x0 0x2 &ipic 22 0x8
> 0xc000 0x0 0x0 0x3 &ipic 23 0x8
> 0xc000 0x0 0x0 0x4 &ipic 20 0x8>;
> interrupt-parent = <&ipic>;
> interrupts = <66 0x8>;
> bus-range = <0 0>;
> ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
> 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
> 0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
> clock-frequency = <66666666>;
> #interrupt-cells = <1>;
> #size-cells = <2>;
> #address-cells = <3>;
> reg = <0xe0008500 0x100>;
> compatible = "fsl,mpc8349-pci";
> device_type = "pci";
> };
>
> pci1: pci@e0008600 {
> cell-index = <2>;
> interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
> interrupt-map = <
>
> /* IDSEL 0x11 */
> 0x8800 0x0 0x0 0x1 &ipic 20 0x8
> 0x8800 0x0 0x0 0x2 &ipic 21 0x8
> 0x8800 0x0 0x0 0x3 &ipic 22 0x8
> 0x8800 0x0 0x0 0x4 &ipic 23 0x8
>
> /* IDSEL 0x12 */
> 0x9000 0x0 0x0 0x1 &ipic 22 0x8
> 0x9000 0x0 0x0 0x2 &ipic 23 0x8
> 0x9000 0x0 0x0 0x3 &ipic 20 0x8
> 0x9000 0x0 0x0 0x4 &ipic 21 0x8
>
> /* IDSEL 0x13 */
> 0x9800 0x0 0x0 0x1 &ipic 23 0x8
> 0x9800 0x0 0x0 0x2 &ipic 20 0x8
> 0x9800 0x0 0x0 0x3 &ipic 21 0x8
> 0x9800 0x0 0x0 0x4 &ipic 22 0x8
>
> /* IDSEL 0x15 */
> 0xa800 0x0 0x0 0x1 &ipic 20 0x8
> 0xa800 0x0 0x0 0x2 &ipic 21 0x8
> 0xa800 0x0 0x0 0x3 &ipic 22 0x8
> 0xa800 0x0 0x0 0x4 &ipic 23 0x8
>
> /* IDSEL 0x16 */
> 0xb000 0x0 0x0 0x1 &ipic 23 0x8
> 0xb000 0x0 0x0 0x2 &ipic 20 0x8
> 0xb000 0x0 0x0 0x3 &ipic 21 0x8
> 0xb000 0x0 0x0 0x4 &ipic 22 0x8
>
> /* IDSEL 0x17 */
> 0xb800 0x0 0x0 0x1 &ipic 22 0x8
> 0xb800 0x0 0x0 0x2 &ipic 23 0x8
> 0xb800 0x0 0x0 0x3 &ipic 20 0x8
> 0xb800 0x0 0x0 0x4 &ipic 21 0x8
>
> /* IDSEL 0x18 */
> 0xc000 0x0 0x0 0x1 &ipic 21 0x8
> 0xc000 0x0 0x0 0x2 &ipic 22 0x8
> 0xc000 0x0 0x0 0x3 &ipic 23 0x8
> 0xc000 0x0 0x0 0x4 &ipic 20 0x8>;
> interrupt-parent = <&ipic>;
> interrupts = <67 0x8>;
> bus-range = <0 0>;
> ranges = <0x02000000 0x0 0xb0000000 0xb0000000 0x0 0x10000000
> 0x42000000 0x0 0xa0000000 0xa0000000 0x0 0x10000000
> 0x01000000 0x0 0x00000000 0xe2100000 0x0 0x00100000>;
> clock-frequency = <66666666>;
> #interrupt-cells = <1>;
> #size-cells = <2>;
> #address-cells = <3>;
> reg = <0xe0008600 0x100>;
> compatible = "fsl,mpc8349-pci";
> device_type = "pci";
> };
>
> chosen {
> linux,stdout-path = &serial0;
> };
> };
>
>
>
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
--
Marco Stornelli
Embedded Software Engineer
CoRiTeL - Consorzio di Ricerca sulle Telecomunicazioni
http://www.coritel.it
marco.stornelli@coritel.it
+39 06 72582838
[-- Attachment #2: Type: text/html, Size: 49050 bytes --]
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: need help with GPIO
2008-09-02 16:59 Laxmikant Rashinkar
@ 2008-09-03 6:37 ` Marco Stornelli
0 siblings, 0 replies; 4+ messages in thread
From: Marco Stornelli @ 2008-09-03 6:37 UTC (permalink / raw)
To: Laxmikant Rashinkar; +Cc: linuxppc-embedded
Hi,
try to understand why the driver doesn't find the device reading the
gpio.c and of_get_gpio(). Maybe the device has been registered as a
platform device and, instead, the driver calls some function for a
specific device.
Regards.
Laxmikant Rashinkar ha scritto:
> Hi Marco,
>
> thanks for your feedback.
>
> I tried out your suggestion of using an offset address instead of an absolute address in the dts, but that did not help.
> I am still getting the error:
>
> LK_DEBUG: gpio.c : of_get_gpio : /localbus/upm@1,0: gpio controller /soc8349@e0000000/gpio-controller@c00: is not registered
>
> thanks
> LK
>
>
>
>
> ----- Original Message ----
> From: Marco Stornelli <marco.stornelli@coritel.it>
> To: Laxmikant Rashinkar <lk.atwork@yahoo.com>
> Cc: linuxppc-embedded@ozlabs.org
> Sent: Monday, September 1, 2008 11:39:05 PM
> Subject: Re: need help with GPIO
>
> Laxmikant Rashinkar ha scritto:
>
>> Hi,
>>
>> I have a MPC8347 based embedded PC running Linux 2.6.27.
>> I am trying to access a NAND device connected to the LBC and UPM.
>> The Ready/Busy* pin of the NAND device is connected to the built in GPIO-1 on pin 4 (input).
>>
>> When I try to access the NAND device, the function of_get_gpio() from drivers/of/gpio.c gets called, and
>> it reports that my GPIO is not registered. Here are the actual debug messages:
>>
>> LK_DEBUG: gpio.c : of_get_gpio : name=upm type=<NULL> index=0
>> LK_DEBUG: gpio.c : of_get_gpio : got property
>> LK_DEBUG: gpio.c : of_get_gpio : nr_cell=3
>> LK_DEBUG: gpio.c : of_get_gpio : gc.name=gpio-controller gc.type=<NULL> gc->Data=0x0
>> LK_DEBUG: gpio.c : of_get_gpio : /localbus/upm@1,0: gpio controller /soc8349@e0000000/gpio-controller@e0000c00: is not registered
>>
>> When I check in /proc/device-tree/soc8349@e0000000/, I find that entries are present for both GPIOs are present.
>>
>> Here are debug registration messages, indicating that gpio registered successfully:
>>
>> ##### LK_DEBUG: of_plat_dev_create : NAME=soc8349
>> ##### LK_DEBUG: of_plat_dev_create : NAME=wdt
>> ##### LK_DEBUG: of_plat_dev_create : NAME=i2c
>> ##### LK_DEBUG: of_plat_dev_create : NAME=i2c
>> ##### LK_DEBUG: of_plat_dev_create : NAME=spi
>> ##### LK_DEBUG: of_plat_dev_create : NAME=dma
>> ##### LK_DEBUG: of_plat_dev_create : NAME=usb
>> ##### LK_DEBUG: of_plat_dev_create : NAME=usb
>> ##### LK_DEBUG: of_plat_dev_create : NAME=mdio
>> ##### LK_DEBUG: of_plat_dev_create : NAME=ethernet
>> ##### LK_DEBUG: of_plat_dev_create : NAME=ethernet
>> ##### LK_DEBUG: of_plat_dev_create : NAME=serial
>> ##### LK_DEBUG: of_plat_dev_create : NAME=serial
>> ##### LK_DEBUG: of_plat_dev_create : NAME=crypto
>> ##### LK_DEBUG: of_plat_dev_create : NAME=pic
>> ##### LK_DEBUG: of_plat_dev_create : NAME=gpio-controller
>> ##### LK_DEBUG: of_plat_dev_create : NAME=gpio-controller
>> ##### LK_DEBUG: of_plat_dev_create : NAME=localbus
>> ##### LK_DEBUG: of_plat_dev_create : NAME=upm
>>
>> Most probably something is wrong in my device tree (listed below). Can someone please point me in the right direction?
>>
>> thanks a lot for your help.
>> LK
>>
>> -------------------------------------------------------------
>>
>> /*
>> * MPC8349E MDS Device Tree Source
>> *
>> * Copyright 2005, 2006 Freescale Semiconductor Inc.
>> *
>> * This program is free software; you can redistribute it and/or modify it
>> * under the terms of the GNU General Public License as published by the
>> * Free Software Foundation; either version 2 of the License, or (at your
>> * option) any later version.
>> */
>>
>> /dts-v1/;
>>
>> / {
>> model = "MPC8349EMDS";
>> compatible = "MPC8349EMDS", "MPC834xMDS", "MPC83xxMDS";
>> #address-cells = <1>;
>> #size-cells = <1>;
>>
>> aliases {
>> ethernet0 = &enet0;
>> ethernet1 = &enet1;
>> serial0 = &serial0;
>> serial1 = &serial1;
>> pci0 = &pci0;
>> pci1 = &pci1;
>> };
>>
>> cpus {
>> #address-cells = <1>;
>> #size-cells = <0>;
>>
>> PowerPC,8349@0 {
>> device_type = "cpu";
>> reg = <0x0>;
>> d-cache-line-size = <32>;
>> i-cache-line-size = <32>;
>> d-cache-size = <32768>;
>> i-cache-size = <32768>;
>> timebase-frequency = <0>; // from bootloader
>> bus-frequency = <0>; // from bootloader
>> clock-frequency = <0>; // from bootloader
>> };
>> };
>>
>> memory {
>> device_type = "memory";
>> reg = <0x00000000 0x10000000>; // 256MB at 0
>> };
>>
>> bcsr@e2400000 {
>> device_type = "board-control";
>> reg = <0xe2400000 0x8000>;
>> };
>>
>> soc8349@e0000000 {
>> #address-cells = <1>;
>> #size-cells = <1>;
>> device_type = "soc";
>> compatible = "simple-bus";
>> ranges = <0x0 0xe0000000 0x00100000>;
>> reg = <0xe0000000 0x00000200>;
>> bus-frequency = <0>;
>>
>> wdt@200 {
>> device_type = "watchdog";
>> compatible = "mpc83xx_wdt";
>> reg = <0x200 0x100>;
>> };
>>
>> i2c@3000 {
>> #address-cells = <1>;
>> #size-cells = <0>;
>> cell-index = <0>;
>> compatible = "fsl-i2c";
>> reg = <0x3000 0x100>;
>> interrupts = <14 0x8>;
>> interrupt-parent = <&ipic>;
>> dfsrr;
>>
>> rtc@68 {
>> compatible = "dallas,ds1374";
>> reg = <0x68>;
>> };
>> };
>>
>> i2c@3100 {
>> #address-cells = <1>;
>> #size-cells = <0>;
>> cell-index = <1>;
>> compatible = "fsl-i2c";
>> reg = <0x3100 0x100>;
>> interrupts = <15 0x8>;
>> interrupt-parent = <&ipic>;
>> dfsrr;
>> };
>>
>> spi@7000 {
>> cell-index = <0>;
>> compatible = "fsl,spi";
>> reg = <0x7000 0x1000>;
>> interrupts = <16 0x8>;
>> interrupt-parent = <&ipic>;
>> mode = "cpu";
>> };
>>
>> dma@82a8 {
>> #address-cells = <1>;
>> #size-cells = <1>;
>> compatible = "fsl,mpc8349-dma", "fsl,elo-dma";
>> reg = <0x82a8 4>;
>> ranges = <0 0x8100 0x1a8>;
>> interrupt-parent = <&ipic>;
>> interrupts = <71 8>;
>> cell-index = <0>;
>> dma-channel@0 {
>> compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
>> reg = <0 0x80>;
>> interrupt-parent = <&ipic>;
>> interrupts = <71 8>;
>> };
>> dma-channel@80 {
>> compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
>> reg = <0x80 0x80>;
>> interrupt-parent = <&ipic>;
>> interrupts = <71 8>;
>> };
>> dma-channel@100 {
>> compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
>> reg = <0x100 0x80>;
>> interrupt-parent = <&ipic>;
>> interrupts = <71 8>;
>> };
>> dma-channel@180 {
>> compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
>> reg = <0x180 0x28>;
>> interrupt-parent = <&ipic>;
>> interrupts = <71 8>;
>> };
>> };
>>
>> /* phy type (ULPI or SERIAL) are only types supported for MPH */
>> /* port = 0 or 1 */
>> usb@22000 {
>> compatible = "fsl-usb2-mph";
>> reg = <0x22000 0x1000>;
>> #address-cells = <1>;
>> #size-cells = <0>;
>> interrupt-parent = <&ipic>;
>> interrupts = <39 0x8>;
>> phy_type = "ulpi";
>> port1;
>> };
>> /* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
>> usb@23000 {
>> compatible = "fsl-usb2-dr";
>> reg = <0x23000 0x1000>;
>> #address-cells = <1>;
>> #size-cells = <0>;
>> interrupt-parent = <&ipic>;
>> interrupts = <38 0x8>;
>> dr_mode = "otg";
>> phy_type = "ulpi";
>> };
>>
>> mdio@24520 {
>> #address-cells = <1>;
>> #size-cells = <0>;
>> compatible = "fsl,gianfar-mdio";
>> reg = <0x24520 0x20>;
>>
>> phy0: ethernet-phy@0 {
>> interrupt-parent = <&ipic>;
>> interrupts = <17 0x8>;
>> reg = <0x1>;
>> device_type = "ethernet-phy";
>> };
>> phy1: ethernet-phy@1 {
>> interrupt-parent = <&ipic>;
>> interrupts = <18 0x8>;
>> reg = <0x2>;
>> device_type = "ethernet-phy";
>> };
>> };
>>
>> enet0: ethernet@24000 {
>> cell-index = <0>;
>> device_type = "network";
>> model = "TSEC";
>> compatible = "gianfar";
>> reg = <0x24000 0x1000>;
>> local-mac-address = [ 00 00 00 00 00 00 ];
>> interrupts = <32 0x8 33 0x8 34 0x8>;
>> interrupt-parent = <&ipic>;
>> phy-handle = <&phy0>;
>> linux,network-index = <0>;
>> };
>>
>> enet1: ethernet@25000 {
>> cell-index = <1>;
>> device_type = "network";
>> model = "TSEC";
>> compatible = "gianfar";
>> reg = <0x25000 0x1000>;
>> local-mac-address = [ 00 00 00 00 00 00 ];
>> interrupts = <35 0x8 36 0x8 37 0x8>;
>> interrupt-parent = <&ipic>;
>> phy-handle = <&phy1>;
>> linux,network-index = <1>;
>> };
>>
>> serial0: serial@4500 {
>> cell-index = <0>;
>> device_type = "serial";
>> compatible = "ns16550";
>> reg = <0x4500 0x100>;
>> clock-frequency = <0>;
>> interrupts = <9 0x8>;
>> interrupt-parent = <&ipic>;
>> };
>>
>> serial1: serial@4600 {
>> cell-index = <1>;
>> device_type = "serial";
>> compatible = "ns16550";
>> reg = <0x4600 0x100>;
>> clock-frequency = <0>;
>> interrupts = <10 0x8>;
>> interrupt-parent = <&ipic>;
>> };
>>
>> crypto@30000 {
>> compatible = "fsl,sec2.0";
>> reg = <0x30000 0x10000>;
>> interrupts = <11 0x8>;
>> interrupt-parent = <&ipic>;
>> fsl,num-channels = <4>;
>> fsl,channel-fifo-len = <24>;
>> fsl,exec-units-mask = <0x7e>;
>> fsl,descriptor-types-mask = <0x01010ebf>;
>> };
>>
>> /* IPIC
>> * interrupts cell = <intr #, sense>
>> * sense values match linux IORESOURCE_IRQ_* defines:
>> * sense == 8: Level, low assertion
>> * sense == 2: Edge, high-to-low change
>> */
>> ipic: pic@700 {
>> interrupt-controller;
>> #address-cells = <0>;
>> #interrupt-cells = <2>;
>> reg = <0x700 0x100>;
>> device_type = "ipic";
>> };
>>
>>
>
> Here you are using absolute addresses but you should use an offset from
> a base reg address, in your case e0000000.
>
>
>> gpio1: gpio-controller@e0000c00 {
>>
> gpio1: gpio-controller@c00 {
>
>> #gpio-cells = <2>;
>> compatible = "fsl,mpc8349-gpio-bank";
>>
> reg = <0xc00 0x100>;
>
>> reg = <0xe0000c00 0x100>;
>> gpio-controller;
>> };
>>
>>
> gpio2: gpio-controller@d00 {
>
>> gpio2: gpio-controller@e0000d00 {
>> #gpio-cells = <2>;
>> compatible = "fsl,mpc8349-gpio-bank";
>>
> reg = <0xd00 0x100>;
>
>> reg = <0xe0000d00 0x100>;
>> gpio-controller;
>> };
>> };
>>
>> localbus {
>> compatible = "fsl,pq3-localbus", "simple-bus";
>> #address-cells = <2>;
>> #size-cells = <1>;
>> reg = <0xe0005000 0x100000>; // BRx, ORx, etc.
>>
>> upm@1,0 {
>> #address-cells = <1>;
>> #size-cells = <1>;
>> compatible = "fsl,upm-nand";
>> reg = <3 0xa0000000 0x800>;
>> fsl,upm-addr-offset = <0x10>;
>> fsl,upm-cmd-offset = <0x08>;
>> gpios = <&gpio1 4 0>;
>>
>> nand@0 {
>> #address-cells = <1>;
>> #size-cells = <1>;
>> compatible = "fsl,lbc-nand";
>>
>> partition@0 {
>> label = "EVERYTHING";
>> reg = <0x00000000 0x01000000>;
>> };
>> };
>> };
>> };
>>
>> pci0: pci@e0008500 {
>> cell-index = <1>;
>> interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
>> interrupt-map = <
>>
>> /* IDSEL 0x11 */
>> 0x8800 0x0 0x0 0x1 &ipic 20 0x8
>> 0x8800 0x0 0x0 0x2 &ipic 21 0x8
>> 0x8800 0x0 0x0 0x3 &ipic 22 0x8
>> 0x8800 0x0 0x0 0x4 &ipic 23 0x8
>>
>> /* IDSEL 0x12 */
>> 0x9000 0x0 0x0 0x1 &ipic 22 0x8
>> 0x9000 0x0 0x0 0x2 &ipic 23 0x8
>> 0x9000 0x0 0x0 0x3 &ipic 20 0x8
>> 0x9000 0x0 0x0 0x4 &ipic 21 0x8
>>
>> /* IDSEL 0x13 */
>> 0x9800 0x0 0x0 0x1 &ipic 23 0x8
>> 0x9800 0x0 0x0 0x2 &ipic 20 0x8
>> 0x9800 0x0 0x0 0x3 &ipic 21 0x8
>> 0x9800 0x0 0x0 0x4 &ipic 22 0x8
>>
>> /* IDSEL 0x15 */
>> 0xa800 0x0 0x0 0x1 &ipic 20 0x8
>> 0xa800 0x0 0x0 0x2 &ipic 21 0x8
>> 0xa800 0x0 0x0 0x3 &ipic 22 0x8
>> 0xa800 0x0 0x0 0x4 &ipic 23 0x8
>>
>> /* IDSEL 0x16 */
>> 0xb000 0x0 0x0 0x1 &ipic 23 0x8
>> 0xb000 0x0 0x0 0x2 &ipic 20 0x8
>> 0xb000 0x0 0x0 0x3 &ipic 21 0x8
>> 0xb000 0x0 0x0 0x4 &ipic 22 0x8
>>
>> /* IDSEL 0x17 */
>> 0xb800 0x0 0x0 0x1 &ipic 22 0x8
>> 0xb800 0x0 0x0 0x2 &ipic 23 0x8
>> 0xb800 0x0 0x0 0x3 &ipic 20 0x8
>> 0xb800 0x0 0x0 0x4 &ipic 21 0x8
>>
>> /* IDSEL 0x18 */
>> 0xc000 0x0 0x0 0x1 &ipic 21 0x8
>> 0xc000 0x0 0x0 0x2 &ipic 22 0x8
>> 0xc000 0x0 0x0 0x3 &ipic 23 0x8
>> 0xc000 0x0 0x0 0x4 &ipic 20 0x8>;
>> interrupt-parent = <&ipic>;
>> interrupts = <66 0x8>;
>> bus-range = <0 0>;
>> ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
>> 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
>> 0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
>> clock-frequency = <66666666>;
>> #interrupt-cells = <1>;
>> #size-cells = <2>;
>> #address-cells = <3>;
>> reg = <0xe0008500 0x100>;
>> compatible = "fsl,mpc8349-pci";
>> device_type = "pci";
>> };
>>
>> pci1: pci@e0008600 {
>> cell-index = <2>;
>> interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
>> interrupt-map = <
>>
>> /* IDSEL 0x11 */
>> 0x8800 0x0 0x0 0x1 &ipic 20 0x8
>> 0x8800 0x0 0x0 0x2 &ipic 21 0x8
>> 0x8800 0x0 0x0 0x3 &ipic 22 0x8
>> 0x8800 0x0 0x0 0x4 &ipic 23 0x8
>>
>> /* IDSEL 0x12 */
>> 0x9000 0x0 0x0 0x1 &ipic 22 0x8
>> 0x9000 0x0 0x0 0x2 &ipic 23 0x8
>> 0x9000 0x0 0x0 0x3 &ipic 20 0x8
>> 0x9000 0x0 0x0 0x4 &ipic 21 0x8
>>
>> /* IDSEL 0x13 */
>> 0x9800 0x0 0x0 0x1 &ipic 23 0x8
>> 0x9800 0x0 0x0 0x2 &ipic 20 0x8
>> 0x9800 0x0 0x0 0x3 &ipic 21 0x8
>> 0x9800 0x0 0x0 0x4 &ipic 22 0x8
>>
>> /* IDSEL 0x15 */
>> 0xa800 0x0 0x0 0x1 &ipic 20 0x8
>> 0xa800 0x0 0x0 0x2 &ipic 21 0x8
>> 0xa800 0x0 0x0 0x3 &ipic 22 0x8
>> 0xa800 0x0 0x0 0x4 &ipic 23 0x8
>>
>> /* IDSEL 0x16 */
>> 0xb000 0x0 0x0 0x1 &ipic 23 0x8
>> 0xb000 0x0 0x0 0x2 &ipic 20 0x8
>> 0xb000 0x0 0x0 0x3 &ipic 21 0x8
>> 0xb000 0x0 0x0 0x4 &ipic 22 0x8
>>
>> /* IDSEL 0x17 */
>> 0xb800 0x0 0x0 0x1 &ipic 22 0x8
>> 0xb800 0x0 0x0 0x2 &ipic 23 0x8
>> 0xb800 0x0 0x0 0x3 &ipic 20 0x8
>> 0xb800 0x0 0x0 0x4 &ipic 21 0x8
>>
>> /* IDSEL 0x18 */
>> 0xc000 0x0 0x0 0x1 &ipic 21 0x8
>> 0xc000 0x0 0x0 0x2 &ipic 22 0x8
>> 0xc000 0x0 0x0 0x3 &ipic 23 0x8
>> 0xc000 0x0 0x0 0x4 &ipic 20 0x8>;
>> interrupt-parent = <&ipic>;
>> interrupts = <67 0x8>;
>> bus-range = <0 0>;
>> ranges = <0x02000000 0x0 0xb0000000 0xb0000000 0x0 0x10000000
>> 0x42000000 0x0 0xa0000000 0xa0000000 0x0 0x10000000
>> 0x01000000 0x0 0x00000000 0xe2100000 0x0 0x00100000>;
>> clock-frequency = <66666666>;
>> #interrupt-cells = <1>;
>> #size-cells = <2>;
>> #address-cells = <3>;
>> reg = <0xe0008600 0x100>;
>> compatible = "fsl,mpc8349-pci";
>> device_type = "pci";
>> };
>>
>> chosen {
>> linux,stdout-path = &serial0;
>> };
>> };
>>
>>
>>
>>
>>
>> ------------------------------------------------------------------------
>>
>> _______________________________________________
>> Linuxppc-embedded mailing list
>> Linuxppc-embedded@ozlabs.org
>> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
>>
>
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
--
Marco Stornelli
Embedded Software Engineer
CoRiTeL - Consorzio di Ricerca sulle Telecomunicazioni
http://www.coritel.it
marco.stornelli@coritel.it
+39 06 72582838
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2008-09-03 6:36 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-09-02 1:21 need help with GPIO Laxmikant Rashinkar
2008-09-02 6:39 ` Marco Stornelli
-- strict thread matches above, loose matches on Subject: below --
2008-09-02 16:59 Laxmikant Rashinkar
2008-09-03 6:37 ` Marco Stornelli
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).