* networking fails to activate
@ 2008-10-14 7:57 Pieter
2008-10-14 22:38 ` Andy Fleming
0 siblings, 1 reply; 5+ messages in thread
From: Pieter @ 2008-10-14 7:57 UTC (permalink / raw)
To: linuxppc-embedded
[-- Attachment #1: Type: text/plain, Size: 728 bytes --]
Hi
We have a powerpc (8548) based board. running eldk4.1. the board has
three ethernet ports using Gainfair ethernet controller v1.2.
If the board powers up with any network cable plugged in, that specific
network is accessible.
if the board powers up without network cables connected and a cable is
plugged in, the network does not become active.
The kernal makes a log entry stating that the phy is up when the cable
is plugged in - but the interface is not pingable
Running ifdown and ifup manually does not result in a pingable interface.
Neither does running /etc/init.d/network restart
can anyone help me pls.
--
Pieter Henning
VASTech
Tel: +27 (0)21 850 5921
Fax: +27 (0)86 503 8941
e-mail: phenning@vastech.co.za
[-- Attachment #2: S/MIME Cryptographic Signature --]
[-- Type: application/x-pkcs7-signature, Size: 2722 bytes --]
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: networking fails to activate
2008-10-14 7:57 networking fails to activate Pieter
@ 2008-10-14 22:38 ` Andy Fleming
2008-10-15 15:03 ` networking fails to activate - more info Pieter
0 siblings, 1 reply; 5+ messages in thread
From: Andy Fleming @ 2008-10-14 22:38 UTC (permalink / raw)
To: Pieter; +Cc: linuxppc-embedded
On Tue, Oct 14, 2008 at 2:57 AM, Pieter <phenning@vastech.co.za> wrote:
> Hi
>
> We have a powerpc (8548) based board. running eldk4.1. the board has
> three ethernet ports using Gainfair ethernet controller v1.2.
>
> If the board powers up with any network cable plugged in, that specific
> network is accessible.
> if the board powers up without network cables connected and a cable is
> plugged in, the network does not become active.
> The kernal makes a log entry stating that the phy is up when the cable
> is plugged in - but the interface is not pingable
> Running ifdown and ifup manually does not result in a pingable interface.
> Neither does running /etc/init.d/network restart
>
> can anyone help me pls.
Check the statistics counters to see if you are getting any bad
packets, or to see if you are getting interrupts. Several people have
reported that their PHYs have powerdown issues, though I wouldn't
expect the PHY to report the link as up, then. Make sure that your
dts specifies the correct PHY address for the connected PHY.
What happens if you start up with the PHY connected, bring up the
interface, and *then* disconnect and reconnect the cable (after a
delay)?
Andy
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: networking fails to activate - more info
2008-10-14 22:38 ` Andy Fleming
@ 2008-10-15 15:03 ` Pieter
2008-10-16 15:02 ` networking fails to activate - even " Pieter
0 siblings, 1 reply; 5+ messages in thread
From: Pieter @ 2008-10-15 15:03 UTC (permalink / raw)
To: linuxppc-embedded; +Cc: Andy Fleming
[-- Attachment #1: Type: text/plain, Size: 2746 bytes --]
>> Hi
>>
>> We have a powerpc (8548) based board. running eldk4.1. the board has
>> three ethernet ports using Gainfair ethernet controller v1.2.
>>
>> If the board powers up with any network cable plugged in, that specific
>> network is accessible.
>> if the board powers up without network cables connected and a cable is
>> plugged in, the network does not become active.
>> The kernal makes a log entry stating that the phy is up when the cable
>> is plugged in - but the interface is not pingable
>> Running ifdown and ifup manually does not result in a pingable interface.
>> Neither does running /etc/init.d/network restart
>>
>> can anyone help me pls.
>>
>
>
> Check the statistics counters to see if you are getting any bad
> packets, or to see if you are getting interrupts. Several people have
> reported that their PHYs have powerdown issues, though I wouldn't
> expect the PHY to report the link as up, then. Make sure that your
> dts specifies the correct PHY address for the connected PHY.
>
> What happens if you start up with the PHY connected, bring up the
> interface, and *then* disconnect and reconnect the cable (after a
> delay)?
Hi
I have checked the counters in both ifconfig and with ethtool. both show
TX counts but no RX count and no errors
ethtool reports that the link is detected.
The phy addresses are correct (ethtool and kernel log shows the
exspected addresses)
I have found that the networking scripts are not called (ifup or down)
when a cable is pluged or unplugged.
I also found that udev is not in my current linux platform - can this
contribute to the problem?
To rule out the phys. I powered on the system with all network cables
plugged in. ping all three to confirm that they work. i then issue a
reset signal (hardware routed) to the phys. when the phys reappear im
still able to ping all three interfaces.
The log file entries for unplugging and connecting the cable are :
(logged by /driver/phy/phy.c )
Oct 15 14:36:56 equus user.info kernel: PHY: 0:00 - Link is
Down
Oct 15 14:36:59 equus user.info kernel: PHY: 0:00 - Link is Up - 100/Full
what is the sequence of events that should follow?
Another test i tried, powered the system up with no cables plugged in
and "ONBOOT=no" in ifcgf-eth sctipts. I then manually run the ifup
scripts one by one. then plug in the three network cables. when i ping
the three interfaces and ping targets on the three networks i find that
one interface is pingable, one is not and one returns "ping: sendto:
Network is unreachable" - these results were reproducible about 25% of
attempts but varied according to order in with cables were plugged in.
I would appreciate any help.
thanks pieter
[-- Attachment #2: S/MIME Cryptographic Signature --]
[-- Type: application/x-pkcs7-signature, Size: 2722 bytes --]
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: networking fails to activate - even more info
2008-10-15 15:03 ` networking fails to activate - more info Pieter
@ 2008-10-16 15:02 ` Pieter
2008-10-27 6:47 ` Solved: " Pieter
0 siblings, 1 reply; 5+ messages in thread
From: Pieter @ 2008-10-16 15:02 UTC (permalink / raw)
To: linuxppc-embedded; +Cc: Andy Fleming
[-- Attachment #1: Type: text/plain, Size: 9998 bytes --]
>>> Hi
>>>
>>> We have a powerpc (8548) based board. running eldk4.1. the board has
>>> three ethernet ports using Gainfair ethernet controller v1.2.
>>>
>>> If the board powers up with any network cable plugged in, that specific
>>> network is accessible.
>>> if the board powers up without network cables connected and a cable is
>>> plugged in, the network does not become active.
>>> The kernal makes a log entry stating that the phy is up when the cable
>>> is plugged in - but the interface is not pingable
>>> Running ifdown and ifup manually does not result in a pingable interface.
>>> Neither does running /etc/init.d/network restart
>>>
>>> can anyone help me pls.
>>>
>>>
>> Check the statistics counters to see if you are getting any bad
>> packets, or to see if you are getting interrupts. Several people have
>> reported that their PHYs have powerdown issues, though I wouldn't
>> expect the PHY to report the link as up, then. Make sure that your
>> dts specifies the correct PHY address for the connected PHY.
>>
>> What happens if you start up with the PHY connected, bring up the
>> interface, and *then* disconnect and reconnect the cable (after a
>> delay)?
>>
> Hi
>
> I have checked the counters in both ifconfig and with ethtool. both show
> TX counts but no RX count and no errors
> ethtool reports that the link is detected.
> The phy addresses are correct (ethtool and kernel log shows the
> exspected addresses)
> I have found that the networking scripts are not called (ifup or down)
> when a cable is pluged or unplugged.
> I also found that udev is not in my current linux platform - can this
> contribute to the problem?
>
> To rule out the phys. I powered on the system with all network cables
> plugged in. ping all three to confirm that they work. i then issue a
> reset signal (hardware routed) to the phys. when the phys reappear im
> still able to ping all three interfaces.
>
> The log file entries for unplugging and connecting the cable are :
> (logged by /driver/phy/phy.c )
> Oct 15 14:36:56 equus user.info kernel: PHY: 0:00 - Link is
> Down
> Oct 15 14:36:59 equus user.info kernel: PHY: 0:00 - Link is Up - 100/Full
> what is the sequence of events that should follow?
>
> Another test i tried, powered the system up with no cables plugged in
> and "ONBOOT=no" in ifcgf-eth sctipts. I then manually run the ifup
> scripts one by one. then plug in the three network cables. when i ping
> the three interfaces and ping targets on the three networks i find that
> one interface is pingable, one is not and one returns "ping: sendto:
> Network is unreachable" - these results were reproducible about 25% of
> attempts but varied according to order in with cables were plugged in.
>
> I would appreciate any help.
> thanks pieter
>
hi
I did some more digging and testing today. To recap the problem: When i
power on the system with network cables plugged in, the interface is
pingable. If the system powers up without network cables plugged in,
ifconfig reports tat all interfaces are up and running. but when
connecting the network cables none of the interfaces are pingable (even
after running ifdown and ifup scripts for the interfaces. )
I think the problem lies some ware in that both ifconfig and ethtool
reports the link as being up even though the system was powered up
without network cables plugged in.
Ifconfigs output:
SDH-25108>
ifconfig
eth0 Link encap:Ethernet HWaddr
00:50:C2:52:51:08
inet addr:10.0.0.200 Bcast:10.0.0.255
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500
Metric:1
RX packets:0 errors:0 dropped:0 overruns:0
frame:0
TX packets:394 errors:0 dropped:0 overruns:0
carrier:0
collisions:0
txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:16548 (16.1
KiB)
Base
address:0xe000
eth1 Link encap:Ethernet HWaddr
00:50:C2:52:51:09
inet addr:172.16.63.237 Bcast:172.16.63.255
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500
Metric:1
RX packets:8676 errors:0 dropped:0 overruns:0
frame:0
TX packets:149 errors:0 dropped:0 overruns:0
carrier:0
collisions:0
txqueuelen:1000
RX bytes:942270 (920.1 KiB) TX bytes:10268 (10.0
KiB)
eth2 Link encap:Ethernet HWaddr
00:50:C2:52:51:0A
inet addr:20.0.0.200 Bcast:20.0.0.255
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500
Metric:1
RX packets:0 errors:0 dropped:0 overruns:0
frame:0
TX packets:4 errors:0 dropped:0 overruns:0
carrier:0
collisions:0
txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:168 (168.0
b)
Base
address:0x2000
lo Link encap:Local
Loopback
inet addr:127.0.0.1
Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436
Metric:1
RX packets:3733 errors:0 dropped:0 overruns:0
frame:0
TX packets:3733 errors:0 dropped:0 overruns:0
carrier:0
collisions:0
txqueuelen:0
RX bytes:674220 (658.4 KiB) TX bytes:674220 (658.4 KiB)
ethtools output:
SDH-25108> ethtool
eth0
Settings for
eth0:
Supported ports: [ TP AUI BNC MII FIBRE
]
Supported link modes: 10baseT/Half
10baseT/Full
100baseT/Half
100baseT/Full
1000baseT/Half
1000baseT/Full
Supports auto-negotiation:
Yes
Advertised link modes: 10baseT/Half
10baseT/Full
100baseT/Half
100baseT/Full
1000baseT/Half
1000baseT/Full
Advertised auto-negotiation:
Yes
Speed:
1000Mb/s
Duplex:
Half
Port:
MII
PHYAD:
0
Transceiver:
external
Auto-negotiation:
off
Current message level: 0x0000003f
(63)
Link detected: yes
If I then plug in the cables and unplug them again the link status goes
down. When plugging in the cables again link status is detected again,
but none of teh interfaces are pingable - even after trying ifdown and up.
[-- Attachment #2: S/MIME Cryptographic Signature --]
[-- Type: application/x-pkcs7-signature, Size: 2722 bytes --]
^ permalink raw reply [flat|nested] 5+ messages in thread* Solved: networking fails to activate - even more info
2008-10-16 15:02 ` networking fails to activate - even " Pieter
@ 2008-10-27 6:47 ` Pieter
0 siblings, 0 replies; 5+ messages in thread
From: Pieter @ 2008-10-27 6:47 UTC (permalink / raw)
To: linuxppc-embedded
[-- Attachment #1: Type: text/plain, Size: 10467 bytes --]
>>>> Hi
>>>>
>>>> We have a powerpc (8548) based board. running eldk4.1. the board has
>>>> three ethernet ports using Gainfair ethernet controller v1.2.
>>>>
>>>> If the board powers up with any network cable plugged in, that specific
>>>> network is accessible.
>>>> if the board powers up without network cables connected and a cable is
>>>> plugged in, the network does not become active.
>>>> The kernal makes a log entry stating that the phy is up when the cable
>>>> is plugged in - but the interface is not pingable
>>>> Running ifdown and ifup manually does not result in a pingable interface.
>>>> Neither does running /etc/init.d/network restart
>>>>
>>>> can anyone help me pls.
>>>>
>>>>
>>>>
>>> Check the statistics counters to see if you are getting any bad
>>> packets, or to see if you are getting interrupts. Several people have
>>> reported that their PHYs have powerdown issues, though I wouldn't
>>> expect the PHY to report the link as up, then. Make sure that your
>>> dts specifies the correct PHY address for the connected PHY.
>>>
>>> What happens if you start up with the PHY connected, bring up the
>>> interface, and *then* disconnect and reconnect the cable (after a
>>> delay)?
>>>
>>>
>> Hi
>>
>> I have checked the counters in both ifconfig and with ethtool. both show
>> TX counts but no RX count and no errors
>> ethtool reports that the link is detected.
>> The phy addresses are correct (ethtool and kernel log shows the
>> exspected addresses)
>> I have found that the networking scripts are not called (ifup or down)
>> when a cable is pluged or unplugged.
>> I also found that udev is not in my current linux platform - can this
>> contribute to the problem?
>>
>> To rule out the phys. I powered on the system with all network cables
>> plugged in. ping all three to confirm that they work. i then issue a
>> reset signal (hardware routed) to the phys. when the phys reappear im
>> still able to ping all three interfaces.
>>
>> The log file entries for unplugging and connecting the cable are :
>> (logged by /driver/phy/phy.c )
>> Oct 15 14:36:56 equus user.info kernel: PHY: 0:00 - Link is
>> Down
>> Oct 15 14:36:59 equus user.info kernel: PHY: 0:00 - Link is Up - 100/Full
>> what is the sequence of events that should follow?
>>
>> Another test i tried, powered the system up with no cables plugged in
>> and "ONBOOT=no" in ifcgf-eth sctipts. I then manually run the ifup
>> scripts one by one. then plug in the three network cables. when i ping
>> the three interfaces and ping targets on the three networks i find that
>> one interface is pingable, one is not and one returns "ping: sendto:
>> Network is unreachable" - these results were reproducible about 25% of
>> attempts but varied according to order in with cables were plugged in.
>>
>> I would appreciate any help.
>> thanks pieter
>>
>>
> hi
>
> I did some more digging and testing today. To recap the problem: When i
> power on the system with network cables plugged in, the interface is
> pingable. If the system powers up without network cables plugged in,
> ifconfig reports tat all interfaces are up and running. but when
> connecting the network cables none of the interfaces are pingable (even
> after running ifdown and ifup scripts for the interfaces. )
>
> I think the problem lies some ware in that both ifconfig and ethtool
> reports the link as being up even though the system was powered up
> without network cables plugged in.
>
> Ifconfigs output:
> SDH-25108>
> ifconfig
>
> eth0 Link encap:Ethernet HWaddr
> 00:50:C2:52:51:08
>
> inet addr:10.0.0.200 Bcast:10.0.0.255
> Mask:255.255.255.0
> UP BROADCAST RUNNING MULTICAST MTU:1500
> Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0
> frame:0
> TX packets:394 errors:0 dropped:0 overruns:0
> carrier:0
> collisions:0
> txqueuelen:1000
>
> RX bytes:0 (0.0 b) TX bytes:16548 (16.1
> KiB)
> Base
> address:0xe000
>
>
>
> eth1 Link encap:Ethernet HWaddr
> 00:50:C2:52:51:09
>
> inet addr:172.16.63.237 Bcast:172.16.63.255
> Mask:255.255.255.0
> UP BROADCAST RUNNING MULTICAST MTU:1500
> Metric:1
> RX packets:8676 errors:0 dropped:0 overruns:0
> frame:0
> TX packets:149 errors:0 dropped:0 overruns:0
> carrier:0
> collisions:0
> txqueuelen:1000
>
> RX bytes:942270 (920.1 KiB) TX bytes:10268 (10.0
> KiB)
>
>
> eth2 Link encap:Ethernet HWaddr
> 00:50:C2:52:51:0A
>
> inet addr:20.0.0.200 Bcast:20.0.0.255
> Mask:255.255.255.0
> UP BROADCAST RUNNING MULTICAST MTU:1500
> Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0
> frame:0
> TX packets:4 errors:0 dropped:0 overruns:0
> carrier:0
> collisions:0
> txqueuelen:1000
>
> RX bytes:0 (0.0 b) TX bytes:168 (168.0
> b)
> Base
> address:0x2000
>
>
>
> lo Link encap:Local
> Loopback
>
> inet addr:127.0.0.1
> Mask:255.0.0.0
>
> UP LOOPBACK RUNNING MTU:16436
> Metric:1
>
> RX packets:3733 errors:0 dropped:0 overruns:0
> frame:0
> TX packets:3733 errors:0 dropped:0 overruns:0
> carrier:0
> collisions:0
> txqueuelen:0
>
> RX bytes:674220 (658.4 KiB) TX bytes:674220 (658.4 KiB)
>
> ethtools output:
> SDH-25108> ethtool
> eth0
>
> Settings for
> eth0:
>
> Supported ports: [ TP AUI BNC MII FIBRE
> ]
> Supported link modes: 10baseT/Half
> 10baseT/Full
> 100baseT/Half
> 100baseT/Full
> 1000baseT/Half
> 1000baseT/Full
> Supports auto-negotiation:
> Yes
>
> Advertised link modes: 10baseT/Half
> 10baseT/Full
> 100baseT/Half
> 100baseT/Full
> 1000baseT/Half
> 1000baseT/Full
> Advertised auto-negotiation:
> Yes
>
> Speed:
> 1000Mb/s
>
> Duplex:
> Half
>
> Port:
> MII
>
> PHYAD:
> 0
>
> Transceiver:
> external
>
> Auto-negotiation:
> off
>
> Current message level: 0x0000003f
> (63)
>
> Link detected: yes
>
> If I then plug in the cables and unplug them again the link status goes
> down. When plugging in the cables again link status is detected again,
> but none of teh interfaces are pingable - even after trying ifdown and up.
>
Hi,
I just wanted to report that the networking problem has been solved by
moving to linux 2.6.24.
pieter
[-- Attachment #2: S/MIME Cryptographic Signature --]
[-- Type: application/x-pkcs7-signature, Size: 2722 bytes --]
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2008-10-27 6:48 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-10-14 7:57 networking fails to activate Pieter
2008-10-14 22:38 ` Andy Fleming
2008-10-15 15:03 ` networking fails to activate - more info Pieter
2008-10-16 15:02 ` networking fails to activate - even " Pieter
2008-10-27 6:47 ` Solved: " Pieter
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).