[QUESTION] 440EPx with PCI to PCIe bridge error

[QUESTION] 440EPx with PCI to PCIe bridge error

[Steven A. Falco]

I have a Sequoia board (440EPx) with kernel 2.6.27.9.  I've recently
plugged in a PLX adapter board to convert one of the PCI connectors
on the Sequoia to PCIe.

When the kernel boots, I get the following error messages regarding
mem resource allocation.  Device 0000:00:0c.0 is the PCI<->PCIe bridge,
and device 0000:01:00.0 is an FPGA PCIe evaluation board.

	PCI host bridge /plb/pci@1ec000000 (primary) ranges:
	 MEM 0x0000000180000000..0x000000018fffffff -> 0x0000000080000000
	  IO 0x00000001e8000000..0x00000001e80fffff -> 0x0000000000000000
	4xx PCI DMA offset set to 0x00000000
	PCI: Probing PCI hardware
	PCI: Hiding 4xx host bridge resources 0000:00:00.0
	pci 0000:00:0c.0: PME# supported from D0 D1 D3hot
	pci 0000:00:0c.0: PME# disabled
	pci 0000:00:0c.0: BAR 8: can't allocate mem resource [0x180000000-0x18fffffff]
	pci 0000:01:00.0: BAR 1: can't allocate mem resource [0x1f0000000-0x1ffffffff]
	pci 0000:01:00.0: BAR 0: can't allocate mem resource [0x180000000-0x18007ffff]
	pci 0000:00:0c.0: PCI bridge, secondary bus 0000:01
	pci 0000:00:0c.0:   IO window: disabled
	pci 0000:00:0c.0:   MEM window: disabled
	pci 0000:00:0c.0:   PREFETCH window: disabled

Plain PCI cards plugged directly into the Sequoia work fine.  Is there
something I have to add to the .dts file to represent the PCI<->PCIe
bridge?

	Thanks,
	Steve

Re: [QUESTION] 440EPx with PCI to PCIe bridge error

[Benjamin Herrenschmidt]

On Mon, 2009-01-05 at 15:09 -0500, Steven A. Falco wrote:
> I have a Sequoia board (440EPx) with kernel 2.6.27.9.  I've recently
> plugged in a PLX adapter board to convert one of the PCI connectors
> on the Sequoia to PCIe.
> 
> When the kernel boots, I get the following error messages regarding
> mem resource allocation.  Device 0000:00:0c.0 is the PCI<->PCIe bridge,
> and device 0000:01:00.0 is an FPGA PCIe evaluation board.

Please enable DEBUG in arch/powerpc/kernel/pci-common.c and pci_32.c and
send us a full log. It might also be useful to do that on top of 2.6.28
in case some of the changes that went in after .27 make a difference.

I think I'll turn those DEBUG into something that can be enabled from
the kernel command line one of these days :-)

Cheers,
Ben.

> 	PCI host bridge /plb/pci@1ec000000 (primary) ranges:
> 	 MEM 0x0000000180000000..0x000000018fffffff -> 0x0000000080000000
> 	  IO 0x00000001e8000000..0x00000001e80fffff -> 0x0000000000000000
> 	4xx PCI DMA offset set to 0x00000000
> 	PCI: Probing PCI hardware
> 	PCI: Hiding 4xx host bridge resources 0000:00:00.0
> 	pci 0000:00:0c.0: PME# supported from D0 D1 D3hot
> 	pci 0000:00:0c.0: PME# disabled
> 	pci 0000:00:0c.0: BAR 8: can't allocate mem resource [0x180000000-0x18fffffff]
> 	pci 0000:01:00.0: BAR 1: can't allocate mem resource [0x1f0000000-0x1ffffffff]
> 	pci 0000:01:00.0: BAR 0: can't allocate mem resource [0x180000000-0x18007ffff]
> 	pci 0000:00:0c.0: PCI bridge, secondary bus 0000:01
> 	pci 0000:00:0c.0:   IO window: disabled
> 	pci 0000:00:0c.0:   MEM window: disabled
> 	pci 0000:00:0c.0:   PREFETCH window: disabled
> 
> Plain PCI cards plugged directly into the Sequoia work fine.  Is there
> something I have to add to the .dts file to represent the PCI<->PCIe
> bridge?
> 
> 	Thanks,
> 	Steve
> 
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-dev

Re: [QUESTION] 440EPx with PCI to PCIe bridge error

[Steven A. Falco]

Benjamin Herrenschmidt wrote:
> On Mon, 2009-01-05 at 15:09 -0500, Steven A. Falco wrote:
>> I have a Sequoia board (440EPx) with kernel 2.6.27.9.  I've recently
>> plugged in a PLX adapter board to convert one of the PCI connectors
>> on the Sequoia to PCIe.
>>
>> When the kernel boots, I get the following error messages regarding
>> mem resource allocation.  Device 0000:00:0c.0 is the PCI<->PCIe bridge,
>> and device 0000:01:00.0 is an FPGA PCIe evaluation board.
> 
> Please enable DEBUG in arch/powerpc/kernel/pci-common.c and pci_32.c and
> send us a full log. It might also be useful to do that on top of 2.6.28
> in case some of the changes that went in after .27 make a difference.
> 
> I think I'll turn those DEBUG into something that can be enabled from
> the kernel command line one of these days :-)
> 
> Cheers,
> Ben.
> 

Here is a complete startup log, with debug turned on as you requested.
This is still against 2.6.27.9, as it will take me a little time to
build 2.6.28.  Hopefully, this log will be useful in the meantime.

	Steve


U-Boot 2008.10-00079-gebb3412 (Dec  9 2008 - 16:06:05)

CPU:   AMCC PowerPC 440EPx Rev. A at 666.666 MHz (PLB=166, OPB=83, EBC=55 MHz)
       Security/Kasumi support
       Bootstrap Option H - Boot ROM Location I2C (Addr 0x52)
       Internal PCI arbiter enabled, PCI async ext clock used
       32 kB I-Cache 32 kB D-Cache
Board: Sequoia - AMCC PPC440EPx Evaluation Board, Rev. F, PCI=66 MHz, serial# 7654
I2C:   ready
SPI:   ready
DTT:   1 is 27 C
DRAM:  256 MB
FLASH: 64 MB
NAND:  32 MiB
PCI:   Bus Dev VenId DevId Class Int
        01  00  1172  0004  ff00  43
        00  0c  10b5  8112  0604  43
In:    serial
Out:   serial
Err:   serial
RTC:   ready
USB:   Host(int phy) Device(ext phy)
Net:   ppc_4xx_eth0, ppc_4xx_eth1
IDE:   Bus 0: OK
  Device 0: PIO mode 4
Model: SMC01GBFK6E Firm: CF080204 Ser#: NU0B4000000000102893
            Type: Hard Disk
            Capacity: 977.4 MB = 0.9 GB (2001888 x 512)



==========================================================
|                                                        |
|                    Welcome to Hydra                    |
|                                                        |
==========================================================



Please type "sm" to enter safe-mode.


Starting current kernel - please wait.
Starting previous kernel - please wait.
Starting safe-mode kernel - please wait.
## Booting kernel from Legacy Image at fd400000 ...
   Image Name:   Linux-2.6.27.9-00045-gcccf182-di
   Created:      2009-01-05  21:29:41 UTC
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1684167 Bytes =  1.6 MB
   Load Address: 00400000
   Entry Point:  00400454
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at fd900000 ...
   Image Name:   initramfs
   Created:      2008-11-26  15:13:12 UTC
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    2443397 Bytes =  2.3 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
   Loading Ramdisk to 0fcb7000, end 0ff0b885 ... OK
CPU clock-frequency <- 0x27bc86a4 (667MHz)
CPU timebase-frequency <- 0x27bc86a4 (667MHz)
/plb: clock-frequency <- 9ef21a9 (167MHz)
/plb/opb: clock-frequency <- 4f790d4 (83MHz)
/plb/opb/ebc: clock-frequency <- 34fb5e3 (56MHz)
/plb/opb/serial@ef600300: clock-frequency <- a8c000 (11MHz)
/plb/opb/serial@ef600400: clock-frequency <- a8c000 (11MHz)
/plb/opb/serial@ef600500: clock-frequency <- a8c000 (11MHz)
/plb/opb/serial@ef600600: clock-frequency <- a8c000 (11MHz)
Memory <- <0x0 0x0 0xffff000> (255MB)
ENET0: local-mac-address <- 00:10:ec:01:04:d0
ENET1: local-mac-address <- 00:10:ec:01:04:d1

zImage starting: loaded at 0x00400000 (sp: 0x0ff0c300)
Allocating 0x371974 bytes for kernel ...
gunzipping (0x00000000 <- 0x0040f000:0x007ac72c)...done 0x35a1e4 bytes
Using loader supplied ramdisk at 0xfcb7000-0xff0b885
initrd head: 0x1f8b0808

Linux/PowerPC load: root=/dev/sda3 rw ip=137.237.178.105:137.237.179.31:137.237.178.1:255.255.255.0:hydra_temp:eth0:off panic=1 console=ttyS0,115200
Finalizing device tree... flat tree at 0x40bf08
Using Hydra_temp machine description
Linux version 2.6.27.9-00045-gcccf182-dirty (sfalco@saf.cs.myharris.net) (gcc version 4.2.2) #135 Mon Jan 5 16:29:11 EST 2009
Found initrd at 0xcfcb7000:0xcff0b885
console [udbg0] enabled
setup_arch: bootmem
arch: exit
Zone PFN ranges:
  DMA      0x00000000 -> 0x0000ffff
  Normal   0x0000ffff -> 0x0000ffff
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x0000ffff
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65023
Kernel command line: root=/dev/sda3 rw ip=137.237.178.105:137.237.179.31:137.237.178.1:255.255.255.0:hydra_temp:eth0:off panic=1 console=ttyS0,115200
UIC0 (32 IRQ sources) at DCR 0xc0
UIC1 (32 IRQ sources) at DCR 0xd0
UIC2 (32 IRQ sources) at DCR 0xe0
PID hash table entries: 1024 (order: 10, 4096 bytes)
clocksource: timebase mult[600000] shift[22] registered
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 253620k/262140k available (3284k kernel code, 8220k reserved, 124k data, 90k bss, 156k init)
SLUB: Genslabs=10, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 1331.20 BogoMIPS (lpj=2662400)
Mount-cache hash table entries: 512
net_namespace: 288 bytes
NET: Registered protocol family 16

PCI host bridge /plb/pci@1ec000000 (primary) ranges:
 MEM 0x0000000180000000..0x000000018fffffff -> 0x0000000080000000
  IO 0x00000001e8000000..0x00000001e80fffff -> 0x0000000000000000
4xx PCI DMA offset set to 0x00000000
PCI: Probing PCI hardware
PCI: Hiding 4xx host bridge resources 0000:00:00.0
pci 0000:00:0c.0: PME# supported from D0 D1 D3hot
pci 0000:00:0c.0: PME# disabled
Try to map irq for 0000:00:00.0...
pci_busdev_to_OF_node(0,0x0)
 parent is /plb/pci@1ec000000
 result is <NULL>
 -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2
 -> mapped to linux irq 16
Try to map irq for 0000:00:0c.0...
pci_busdev_to_OF_node(0,0x60)
 parent is /plb/pci@1ec000000
 result is <NULL>
 -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2
 -> mapped to linux irq 16
Try to map irq for 0000:01:00.0...
pci_busdev_to_OF_node(1,0x0)
pci_busdev_to_OF_node(0,0x60)
 parent is /plb/pci@1ec000000
 result is <NULL>
 -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2
 -> mapped to linux irq 16
PCI: PHB (bus 0) bridge rsrc 0: 0000000000000000-00000000000fffff [0x100], parent c0339b40 (PCI IO)
PCI: PHB (bus 0) bridge rsrc 1: 0000000180000000-000000018fffffff [0x200], parent c0339b18 (PCI mem)
PCI: Assigning unassigned resouces...
pci 0000:00:0c.0: BAR 8: can't allocate mem resource [0x180000000-0x18fffffff]
pci 0000:01:00.0: BAR 1: can't allocate mem resource [0x1f0000000-0x1ffffffff]
pci 0000:01:00.0: BAR 0: can't allocate mem resource [0x180000000-0x18007ffff]
pci 0000:00:0c.0: PCI bridge, secondary bus 0000:01
pci 0000:00:0c.0:   IO window: disabled
pci 0000:00:0c.0:   MEM window: disabled
pci 0000:00:0c.0:   PREFETCH window: disabled
bus: 00 index 0 io port: [0, fffff]
bus: 00 index 1 mmio: [180000000, 18fffffff]
bus: 01 index 0 mmio: [0, 0]
bus: 01 index 1 mmio: [0, 0]
bus: 01 index 2 mmio: [0, 0]
bus: 01 index 3 mmio: [0, 0]
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Freeing initrd memory: 2386k freed
msgmni has been set to 500
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x1ef600300 (irq = 17) is a 16550A
                                                              console handover: boot [udbg0] -> real [ttyS0]
serial8250.0: ttyS1 at MMIO 0x1ef600400 (irq = 18) is a 16550A
serial8250.0: ttyS2 at MMIO 0x1ef600500 (irq = 19) is a 16550A
serial8250.0: ttyS3 at MMIO 0x1ef600600 (irq = 20) is a 16550A
1ef600300.serial: ttyS0 at MMIO 0x1ef600300 (irq = 17) is a 16550A
1ef600400.serial: ttyS1 at MMIO 0x1ef600400 (irq = 18) is a 16550A
1ef600500.serial: ttyS2 at MMIO 0x1ef600500 (irq = 19) is a 16550A
1ef600600.serial: ttyS3 at MMIO 0x1ef600600 (irq = 20) is a 16550A
brd: module loaded
PPC 4xx OCP EMAC driver, version 3.54
MAL v2 /plb/mcmal, 2 TX channels, 2 RX channels
ZMII /plb/opb/emac-zmii@ef600d00 initialized
RGMII /plb/opb/emac-rgmii@ef601000 initialized with MDIO support
/plb/opb/emac-rgmii@ef601000: input 0 in RGMII mode
eth0: EMAC-0 /plb/opb/ethernet@ef600e00, MAC 00:10:ec:01:04:d0
eth0: found Marvell 88E1111 Ethernet PHY (0x00)
/plb/opb/emac-rgmii@ef601000: input 1 in RGMII mode
eth1: EMAC-1 /plb/opb/ethernet@ef600f00, MAC 00:10:ec:01:04:d1
eth1: found Marvell 88E1111 Ethernet PHY (0x01)
Uniform Multi-Platform E-IDE driver
Driver 'sd' needs updating - please use bus_type methods
scsi0 : pata_platform
ata1: PATA max PIO6 mmio cmd 0x1c1000000 ctl 0x1c1000098 irq 32
ata1.00: ATA-0: SMC01GBFK6E, CF080204, max MWDMA2
ata1.00: 2001888 sectors, multi 0: LBA
ata1.00: configured for PIO
ata1.00: configured for PIO
ata1: EH complete
scsi 0:0:0:0: Direct-Access     ATA      SMC01GBFK6E      CF08 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
1fc000000.nor_flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
1fc000000.nor_flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Creating 9 MTD partitions on "1fc000000.nor_flash":
0x00000000-0x00500000 : "kernel0"
0x00500000-0x00a00000 : "ramdisk0"
0x00a00000-0x00f00000 : "kernel1"
0x00f00000-0x01400000 : "ramdisk1"
0x01400000-0x01900000 : "kernel2"
0x01900000-0x01e00000 : "ramdisk2"
0x03f60000-0x03f80000 : "env0"
0x03f80000-0x03fa0000 : "env1"
0x03fa0000-0x04000000 : "u-boot"
spi_ppc4xx_of 1ef600900.spi: driver initialized
ppc-of-ehci e0000300.ehci: OF EHCI
ppc-of-ehci e0000300.ehci: new USB bus registered, assigned bus number 1
ppc-of-ehci e0000300.ehci: irq 34, io mem 0xe0000300
ppc-of-ehci e0000300.ehci: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OF EHCI
usb usb1: Manufacturer: Linux 2.6.27.9-00045-gcccf182-dirty ehci_hcd
usb usb1: SerialNumber: PPC-OF USB
ppc-of-ohci e0000400.usb: OF OHCI
ppc-of-ohci e0000400.usb: new USB bus registered, assigned bus number 2
ppc-of-ohci e0000400.usb: irq 35, io mem 0xe0000400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OF OHCI
usb usb2: Manufacturer: Linux 2.6.27.9-00045-gcccf182-dirty ohci_hcd
usb usb2: SerialNumber: PPC-OF USB
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
rtc-m41t80 0-0068: chip found, driver version 0.05
rtc-m41t80 0-0068: rtc core: registered m41t65 as rtc0
ibm-iic 1ef600700.i2c: using standard (100 kHz) mode
ibm-iic 1ef600800.i2c: using standard (100 kHz) mode
at24 0-0052: 512 byte 24c04 EEPROM (writable)
ad7414 0-0048: chip found
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-m41t80 0-0068: setting system clock to 2009-01-05 11:33:38 UTC (1231155218)
eth0: link is down
eth0: link is up, 100 FDX, pause enabled
IP-Config: Complete:
     device=eth0, addr=137.237.178.105, mask=255.255.255.0, gw=137.237.178.1,
     host=hydra_temp, domain=, nis-domain=(none),
     bootserver=137.237.179.31, rootserver=137.237.179.31, rootpath=
Freeing unused kernel memory: 156k init
Checking /dev/sda1
Checking /dev/sda2
Checking /dev/sda3
Checking /dev/sda4
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
init started: BusyBox v1.10.4 (2008-10-27 12:52:02 EDT)
starting pid 889, tty '/dev/ttyS0': '/etc/init.d/rcS'
launcher[944]: launching /bin/craft on /dev/ttyS0
Hydra>

Re: [QUESTION] 440EPx with PCI to PCIe bridge error

[Benjamin Herrenschmidt]

> Here is a complete startup log, with debug turned on as you requested.
> This is still against 2.6.27.9, as it will take me a little time to
> build 2.6.28.  Hopefully, this log will be useful in the meantime.

Can you add "debug" to your kernel command line option or send the
output of the "dmesg" command please ?

Cheers,
Ben.

> 	Steve
> 
> 
> U-Boot 2008.10-00079-gebb3412 (Dec  9 2008 - 16:06:05)
> 
> CPU:   AMCC PowerPC 440EPx Rev. A at 666.666 MHz (PLB=166, OPB=83, EBC=55 MHz)
>        Security/Kasumi support
>        Bootstrap Option H - Boot ROM Location I2C (Addr 0x52)
>        Internal PCI arbiter enabled, PCI async ext clock used
>        32 kB I-Cache 32 kB D-Cache
> Board: Sequoia - AMCC PPC440EPx Evaluation Board, Rev. F, PCI=66 MHz, serial# 7654
> I2C:   ready
> SPI:   ready
> DTT:   1 is 27 C
> DRAM:  256 MB
> FLASH: 64 MB
> NAND:  32 MiB
> PCI:   Bus Dev VenId DevId Class Int
>         01  00  1172  0004  ff00  43
>         00  0c  10b5  8112  0604  43
> In:    serial
> Out:   serial
> Err:   serial
> RTC:   ready
> USB:   Host(int phy) Device(ext phy)
> Net:   ppc_4xx_eth0, ppc_4xx_eth1
> IDE:   Bus 0: OK
>   Device 0: PIO mode 4
> Model: SMC01GBFK6E Firm: CF080204 Ser#: NU0B4000000000102893
>             Type: Hard Disk
>             Capacity: 977.4 MB = 0.9 GB (2001888 x 512)
> 
> 
> 
> ==========================================================
> |                                                        |
> |                    Welcome to Hydra                    |
> |                                                        |
> ==========================================================
> 
> 
> 
> Please type "sm" to enter safe-mode.
> 
> 
> Starting current kernel - please wait.
> Starting previous kernel - please wait.
> Starting safe-mode kernel - please wait.
> ## Booting kernel from Legacy Image at fd400000 ...
>    Image Name:   Linux-2.6.27.9-00045-gcccf182-di
>    Created:      2009-01-05  21:29:41 UTC
>    Image Type:   PowerPC Linux Kernel Image (gzip compressed)
>    Data Size:    1684167 Bytes =  1.6 MB
>    Load Address: 00400000
>    Entry Point:  00400454
>    Verifying Checksum ... OK
> ## Loading init Ramdisk from Legacy Image at fd900000 ...
>    Image Name:   initramfs
>    Created:      2008-11-26  15:13:12 UTC
>    Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
>    Data Size:    2443397 Bytes =  2.3 MB
>    Load Address: 00000000
>    Entry Point:  00000000
>    Verifying Checksum ... OK
>    Uncompressing Kernel Image ... OK
>    Loading Ramdisk to 0fcb7000, end 0ff0b885 ... OK
> CPU clock-frequency <- 0x27bc86a4 (667MHz)
> CPU timebase-frequency <- 0x27bc86a4 (667MHz)
> /plb: clock-frequency <- 9ef21a9 (167MHz)
> /plb/opb: clock-frequency <- 4f790d4 (83MHz)
> /plb/opb/ebc: clock-frequency <- 34fb5e3 (56MHz)
> /plb/opb/serial@ef600300: clock-frequency <- a8c000 (11MHz)
> /plb/opb/serial@ef600400: clock-frequency <- a8c000 (11MHz)
> /plb/opb/serial@ef600500: clock-frequency <- a8c000 (11MHz)
> /plb/opb/serial@ef600600: clock-frequency <- a8c000 (11MHz)
> Memory <- <0x0 0x0 0xffff000> (255MB)
> ENET0: local-mac-address <- 00:10:ec:01:04:d0
> ENET1: local-mac-address <- 00:10:ec:01:04:d1
> 
> zImage starting: loaded at 0x00400000 (sp: 0x0ff0c300)
> Allocating 0x371974 bytes for kernel ...
> gunzipping (0x00000000 <- 0x0040f000:0x007ac72c)...done 0x35a1e4 bytes
> Using loader supplied ramdisk at 0xfcb7000-0xff0b885
> initrd head: 0x1f8b0808
> 
> Linux/PowerPC load: root=/dev/sda3 rw ip=137.237.178.105:137.237.179.31:137.237.178.1:255.255.255.0:hydra_temp:eth0:off panic=1 console=ttyS0,115200
> Finalizing device tree... flat tree at 0x40bf08
> Using Hydra_temp machine description
> Linux version 2.6.27.9-00045-gcccf182-dirty (sfalco@saf.cs.myharris.net) (gcc version 4.2.2) #135 Mon Jan 5 16:29:11 EST 2009
> Found initrd at 0xcfcb7000:0xcff0b885
> console [udbg0] enabled
> setup_arch: bootmem
> arch: exit
> Zone PFN ranges:
>   DMA      0x00000000 -> 0x0000ffff
>   Normal   0x0000ffff -> 0x0000ffff
> Movable zone start PFN for each node
> early_node_map[1] active PFN ranges
>     0: 0x00000000 -> 0x0000ffff
> Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65023
> Kernel command line: root=/dev/sda3 rw ip=137.237.178.105:137.237.179.31:137.237.178.1:255.255.255.0:hydra_temp:eth0:off panic=1 console=ttyS0,115200
> UIC0 (32 IRQ sources) at DCR 0xc0
> UIC1 (32 IRQ sources) at DCR 0xd0
> UIC2 (32 IRQ sources) at DCR 0xe0
> PID hash table entries: 1024 (order: 10, 4096 bytes)
> clocksource: timebase mult[600000] shift[22] registered
> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> Memory: 253620k/262140k available (3284k kernel code, 8220k reserved, 124k data, 90k bss, 156k init)
> SLUB: Genslabs=10, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> Calibrating delay loop... 1331.20 BogoMIPS (lpj=2662400)
> Mount-cache hash table entries: 512
> net_namespace: 288 bytes
> NET: Registered protocol family 16
> 
> PCI host bridge /plb/pci@1ec000000 (primary) ranges:
>  MEM 0x0000000180000000..0x000000018fffffff -> 0x0000000080000000
>   IO 0x00000001e8000000..0x00000001e80fffff -> 0x0000000000000000
> 4xx PCI DMA offset set to 0x00000000
> PCI: Probing PCI hardware
> PCI: Hiding 4xx host bridge resources 0000:00:00.0
> pci 0000:00:0c.0: PME# supported from D0 D1 D3hot
> pci 0000:00:0c.0: PME# disabled
> Try to map irq for 0000:00:00.0...
> pci_busdev_to_OF_node(0,0x0)
>  parent is /plb/pci@1ec000000
>  result is <NULL>
>  -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2
>  -> mapped to linux irq 16
> Try to map irq for 0000:00:0c.0...
> pci_busdev_to_OF_node(0,0x60)
>  parent is /plb/pci@1ec000000
>  result is <NULL>
>  -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2
>  -> mapped to linux irq 16
> Try to map irq for 0000:01:00.0...
> pci_busdev_to_OF_node(1,0x0)
> pci_busdev_to_OF_node(0,0x60)
>  parent is /plb/pci@1ec000000
>  result is <NULL>
>  -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2
>  -> mapped to linux irq 16
> PCI: PHB (bus 0) bridge rsrc 0: 0000000000000000-00000000000fffff [0x100], parent c0339b40 (PCI IO)
> PCI: PHB (bus 0) bridge rsrc 1: 0000000180000000-000000018fffffff [0x200], parent c0339b18 (PCI mem)
> PCI: Assigning unassigned resouces...
> pci 0000:00:0c.0: BAR 8: can't allocate mem resource [0x180000000-0x18fffffff]
> pci 0000:01:00.0: BAR 1: can't allocate mem resource [0x1f0000000-0x1ffffffff]
> pci 0000:01:00.0: BAR 0: can't allocate mem resource [0x180000000-0x18007ffff]
> pci 0000:00:0c.0: PCI bridge, secondary bus 0000:01
> pci 0000:00:0c.0:   IO window: disabled
> pci 0000:00:0c.0:   MEM window: disabled
> pci 0000:00:0c.0:   PREFETCH window: disabled
> bus: 00 index 0 io port: [0, fffff]
> bus: 00 index 1 mmio: [180000000, 18fffffff]
> bus: 01 index 0 mmio: [0, 0]
> bus: 01 index 1 mmio: [0, 0]
> bus: 01 index 2 mmio: [0, 0]
> bus: 01 index 3 mmio: [0, 0]
> SCSI subsystem initialized
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> NET: Registered protocol family 2
> IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
> TCP established hash table entries: 8192 (order: 4, 65536 bytes)
> TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
> TCP: Hash tables configured (established 8192 bind 8192)
> TCP reno registered
> NET: Registered protocol family 1
> checking if image is initramfs... it is
> Freeing initrd memory: 2386k freed
> msgmni has been set to 500
> io scheduler noop registered
> io scheduler anticipatory registered (default)
> io scheduler deadline registered
> io scheduler cfq registered
> Serial: 8250/16550 driver4 ports, IRQ sharing enabled
> serial8250.0: ttyS0 at MMIO 0x1ef600300 (irq = 17) is a 16550A
>                                                               console handover: boot [udbg0] -> real [ttyS0]
> serial8250.0: ttyS1 at MMIO 0x1ef600400 (irq = 18) is a 16550A
> serial8250.0: ttyS2 at MMIO 0x1ef600500 (irq = 19) is a 16550A
> serial8250.0: ttyS3 at MMIO 0x1ef600600 (irq = 20) is a 16550A
> 1ef600300.serial: ttyS0 at MMIO 0x1ef600300 (irq = 17) is a 16550A
> 1ef600400.serial: ttyS1 at MMIO 0x1ef600400 (irq = 18) is a 16550A
> 1ef600500.serial: ttyS2 at MMIO 0x1ef600500 (irq = 19) is a 16550A
> 1ef600600.serial: ttyS3 at MMIO 0x1ef600600 (irq = 20) is a 16550A
> brd: module loaded
> PPC 4xx OCP EMAC driver, version 3.54
> MAL v2 /plb/mcmal, 2 TX channels, 2 RX channels
> ZMII /plb/opb/emac-zmii@ef600d00 initialized
> RGMII /plb/opb/emac-rgmii@ef601000 initialized with MDIO support
> /plb/opb/emac-rgmii@ef601000: input 0 in RGMII mode
> eth0: EMAC-0 /plb/opb/ethernet@ef600e00, MAC 00:10:ec:01:04:d0
> eth0: found Marvell 88E1111 Ethernet PHY (0x00)
> /plb/opb/emac-rgmii@ef601000: input 1 in RGMII mode
> eth1: EMAC-1 /plb/opb/ethernet@ef600f00, MAC 00:10:ec:01:04:d1
> eth1: found Marvell 88E1111 Ethernet PHY (0x01)
> Uniform Multi-Platform E-IDE driver
> Driver 'sd' needs updating - please use bus_type methods
> scsi0 : pata_platform
> ata1: PATA max PIO6 mmio cmd 0x1c1000000 ctl 0x1c1000098 irq 32
> ata1.00: ATA-0: SMC01GBFK6E, CF080204, max MWDMA2
> ata1.00: 2001888 sectors, multi 0: LBA
> ata1.00: configured for PIO
> ata1.00: configured for PIO
> ata1: EH complete
> scsi 0:0:0:0: Direct-Access     ATA      SMC01GBFK6E      CF08 PQ: 0 ANSI: 5
> sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
> sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
>  sda: sda1 sda2 sda3 sda4
> sd 0:0:0:0: [sda] Attached SCSI disk
> sd 0:0:0:0: Attached scsi generic sg0 type 0
> 1fc000000.nor_flash: Found 1 x16 devices at 0x0 in 16-bit bank
>  Amd/Fujitsu Extended Query Table at 0x0040
> 1fc000000.nor_flash: CFI does not contain boot bank location. Assuming top.
> number of CFI chips: 1
> cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
> RedBoot partition parsing not available
> Creating 9 MTD partitions on "1fc000000.nor_flash":
> 0x00000000-0x00500000 : "kernel0"
> 0x00500000-0x00a00000 : "ramdisk0"
> 0x00a00000-0x00f00000 : "kernel1"
> 0x00f00000-0x01400000 : "ramdisk1"
> 0x01400000-0x01900000 : "kernel2"
> 0x01900000-0x01e00000 : "ramdisk2"
> 0x03f60000-0x03f80000 : "env0"
> 0x03f80000-0x03fa0000 : "env1"
> 0x03fa0000-0x04000000 : "u-boot"
> spi_ppc4xx_of 1ef600900.spi: driver initialized
> ppc-of-ehci e0000300.ehci: OF EHCI
> ppc-of-ehci e0000300.ehci: new USB bus registered, assigned bus number 1
> ppc-of-ehci e0000300.ehci: irq 34, io mem 0xe0000300
> ppc-of-ehci e0000300.ehci: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 1 port detected
> usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
> usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> usb usb1: Product: OF EHCI
> usb usb1: Manufacturer: Linux 2.6.27.9-00045-gcccf182-dirty ehci_hcd
> usb usb1: SerialNumber: PPC-OF USB
> ppc-of-ohci e0000400.usb: OF OHCI
> ppc-of-ohci e0000400.usb: new USB bus registered, assigned bus number 2
> ppc-of-ohci e0000400.usb: irq 35, io mem 0xe0000400
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 1 port detected
> usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
> usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> usb usb2: Product: OF OHCI
> usb usb2: Manufacturer: Linux 2.6.27.9-00045-gcccf182-dirty ohci_hcd
> usb usb2: SerialNumber: PPC-OF USB
> Initializing USB Mass Storage driver...
> usbcore: registered new interface driver usb-storage
> USB Mass Storage support registered.
> i2c /dev entries driver
> rtc-m41t80 0-0068: chip found, driver version 0.05
> rtc-m41t80 0-0068: rtc core: registered m41t65 as rtc0
> ibm-iic 1ef600700.i2c: using standard (100 kHz) mode
> ibm-iic 1ef600800.i2c: using standard (100 kHz) mode
> at24 0-0052: 512 byte 24c04 EEPROM (writable)
> ad7414 0-0048: chip found
> TCP cubic registered
> NET: Registered protocol family 17
> RPC: Registered udp transport module.
> RPC: Registered tcp transport module.
> rtc-m41t80 0-0068: setting system clock to 2009-01-05 11:33:38 UTC (1231155218)
> eth0: link is down
> eth0: link is up, 100 FDX, pause enabled
> IP-Config: Complete:
>      device=eth0, addr=137.237.178.105, mask=255.255.255.0, gw=137.237.178.1,
>      host=hydra_temp, domain=, nis-domain=(none),
>      bootserver=137.237.179.31, rootserver=137.237.179.31, rootpath=
> Freeing unused kernel memory: 156k init
> Checking /dev/sda1
> Checking /dev/sda2
> Checking /dev/sda3
> Checking /dev/sda4
> kjournald starting.  Commit interval 5 seconds
> EXT3 FS on sda3, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting.  Commit interval 5 seconds
> EXT3 FS on sda1, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting.  Commit interval 5 seconds
> EXT3 FS on sda2, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting.  Commit interval 5 seconds
> EXT3 FS on sda4, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> init started: BusyBox v1.10.4 (2008-10-27 12:52:02 EDT)
> starting pid 889, tty '/dev/ttyS0': '/etc/init.d/rcS'
> launcher[944]: launching /bin/craft on /dev/ttyS0
> Hydra>

Re: [QUESTION] 440EPx with PCI to PCIe bridge error

[Steven A. Falco]

Benjamin Herrenschmidt wrote:
> 
>> Here is a complete startup log, with debug turned on as you requested.
>> This is still against 2.6.27.9, as it will take me a little time to
>> build 2.6.28.  Hopefully, this log will be useful in the meantime.
> 
> Can you add "debug" to your kernel command line option or send the
> output of the "dmesg" command please ?
> 

Here is the output of dmesg:

$ dmesg
Using Hydra_temp machine description
Linux version 2.6.27.9-00045-gcccf182-dirty (sfalco@saf.cs.myharris.net) (gcc version 4.2.2) #135 Mon Jan 5 16:29:11 EST 2009
Found initrd at 0xcfcb7000:0xcff0b885
Found legacy serial port 0 for /plb/opb/serial@ef600300
  mem=1ef600300, taddr=1ef600300, irq=0, clk=11059200, speed=115200
Found legacy serial port 1 for /plb/opb/serial@ef600400
  mem=1ef600400, taddr=1ef600400, irq=0, clk=11059200, speed=0
Found legacy serial port 2 for /plb/opb/serial@ef600500
  mem=1ef600500, taddr=1ef600500, irq=0, clk=11059200, speed=0
Found legacy serial port 3 for /plb/opb/serial@ef600600
  mem=1ef600600, taddr=1ef600600, irq=0, clk=11059200, speed=0
console [udbg0] enabled
Top of RAM: 0xffff000, Total RAM: 0xffff000
Memory hole size: 0MB
Zone PFN ranges:
  DMA      0x00000000 -> 0x0000ffff
  Normal   0x0000ffff -> 0x0000ffff
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x0000ffff
On node 0 totalpages: 65535
free_area_init_node: node 0, pgdat c03522f0, node_mem_map c040f000
  DMA zone: 65023 pages, LIFO batch:15
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65023
Kernel command line: root=/dev/sda3 rw ip=137.237.178.105:137.237.179.31:137.237.178.1:255.255.255.0:hydra_temp:eth0:off panic=1 console=ttyS0,115200
UIC0 (32 IRQ sources) at DCR 0xc0
UIC1 (32 IRQ sources) at DCR 0xd0
UIC2 (32 IRQ sources) at DCR 0xe0
PID hash table entries: 1024 (order: 10, 4096 bytes)
time_init: decrementer frequency = 666.666660 MHz
time_init: processor frequency   = 666.666660 MHz
clocksource: timebase mult[600000] shift[22] registered
clockevent: decrementer mult[aaaa] shift[16] cpu[0]
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 253620k/262140k available (3284k kernel code, 8220k reserved, 124k data, 90k bss, 156k init)
SLUB: Genslabs=10, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 1331.20 BogoMIPS (lpj=2662400)
Mount-cache hash table entries: 512
net_namespace: 288 bytes
NET: Registered protocol family 16
PCI host bridge /plb/pci@1ec000000 (primary) ranges:
 MEM 0x0000000180000000..0x000000018fffffff -> 0x0000000080000000
  IO 0x00000001e8000000..0x00000001e80fffff -> 0x0000000000000000
4xx PCI DMA offset set to 0x00000000
PCI: Probing PCI hardware
PCI: 0000:00:00.0 reg 14 32bit mmio: [0, 7fffffff]
PCI:0000:00:00.0 Resource 1 0000000000000000-000000007fffffff [21208] is unassigned
PCI: Hiding 4xx host bridge resources 0000:00:00.0
pci 0000:00:00.0: supports D1
pci 0000:00:0c.0: supports D1
pci 0000:00:0c.0: PME# supported from D0 D1 D3hot
pci 0000:00:0c.0: PME# disabled
PCI: Fixup bus 0 (PHB)
Try to map irq for 0000:00:00.0...
pci_busdev_to_OF_node(0,0x0)
 parent is /plb/pci@1ec000000
 result is <NULL>
 -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2
 -> mapped to linux irq 16
Try to map irq for 0000:00:0c.0...
pci_busdev_to_OF_node(0,0x60)
 parent is /plb/pci@1ec000000
 result is <NULL>
 -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2
 -> mapped to linux irq 16
PCI: 0000:01:00.0 reg 10 32bit mmio: [80000000, 8007ffff]
PCI: 0000:01:00.0 reg 14 32bit mmio: [f0000000, ffffffff]
PCI:0000:01:00.0 Resource 0 0000000080000000-000000008007ffff [20200] fixup...
PCI:0000:01:00.0            0000000180000000-000000018007ffff
PCI:0000:01:00.0 Resource 1 00000000f0000000-00000000ffffffff [20200] fixup...
PCI:0000:01:00.0            00000001f0000000-00000001ffffffff
PCI: bridge 0000:00:0c.0 32bit mmio: [80000000, 800fffff]
PCI: Fixup bus 1 (0000:00:0c.0)
PCI:0000:00:0c.0 Bus rsrc 1 0000000080000000-00000000800fffff [200] fixup...
PCI:0000:00:0c.0            0000000180000000-00000001800fffff
Try to map irq for 0000:01:00.0...
pci_busdev_to_OF_node(1,0x0)
pci_busdev_to_OF_node(0,0x60)
 parent is /plb/pci@1ec000000
 result is <NULL>
 -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2
 -> mapped to linux irq 16
PCI: PHB (bus 0) bridge rsrc 0: 0000000000000000-00000000000fffff [0x100], parent c0339b40 (PCI IO)
PCI: PHB (bus 0) bridge rsrc 1: 0000000180000000-000000018fffffff [0x200], parent c0339b18 (PCI mem)
PCI: Assigning unassigned resouces...
pci 0000:00:0c.0: BAR 8: can't allocate mem resource [0x180000000-0x18fffffff]
pci 0000:01:00.0: BAR 1: can't allocate mem resource [0x1f0000000-0x1ffffffff]
pci 0000:01:00.0: BAR 0: can't allocate mem resource [0x180000000-0x18007ffff]
pci 0000:00:0c.0: PCI bridge, secondary bus 0000:01
pci 0000:00:0c.0:   IO window: disabled
pci 0000:00:0c.0:   MEM window: disabled
pci 0000:00:0c.0:   PREFETCH window: disabled
bus: 00 index 0 io port: [0, fffff]
bus: 00 index 1 mmio: [180000000, 18fffffff]
bus: 01 index 0 mmio: [0, 0]
bus: 01 index 1 mmio: [0, 0]
bus: 01 index 2 mmio: [0, 0]
bus: 01 index 3 mmio: [0, 0]
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Switched to high resolution mode on CPU 0
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Freeing initrd memory: 2386k freed
msgmni has been set to 500
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x1ef600300 (irq = 17) is a 16550A
console handover: boot [udbg0] -> real [ttyS0]
serial8250.0: ttyS1 at MMIO 0x1ef600400 (irq = 18) is a 16550A
serial8250.0: ttyS2 at MMIO 0x1ef600500 (irq = 19) is a 16550A
serial8250.0: ttyS3 at MMIO 0x1ef600600 (irq = 20) is a 16550A
1ef600300.serial: ttyS0 at MMIO 0x1ef600300 (irq = 17) is a 16550A
1ef600400.serial: ttyS1 at MMIO 0x1ef600400 (irq = 18) is a 16550A
1ef600500.serial: ttyS2 at MMIO 0x1ef600500 (irq = 19) is a 16550A
1ef600600.serial: ttyS3 at MMIO 0x1ef600600 (irq = 20) is a 16550A
brd: module loaded
PPC 4xx OCP EMAC driver, version 3.54
MAL v2 /plb/mcmal, 2 TX channels, 2 RX channels
ZMII /plb/opb/emac-zmii@ef600d00 initialized
RGMII /plb/opb/emac-rgmii@ef601000 initialized with MDIO support
/plb/opb/emac-rgmii@ef601000: input 0 in RGMII mode
eth0: EMAC-0 /plb/opb/ethernet@ef600e00, MAC 00:10:ec:01:04:d0
eth0: found Marvell 88E1111 Ethernet PHY (0x00)
/plb/opb/emac-rgmii@ef601000: input 1 in RGMII mode
eth1: EMAC-1 /plb/opb/ethernet@ef600f00, MAC 00:10:ec:01:04:d1
eth1: found Marvell 88E1111 Ethernet PHY (0x01)
Uniform Multi-Platform E-IDE driver
Driver 'sd' needs updating - please use bus_type methods
scsi0 : pata_platform
ata1: PATA max PIO6 mmio cmd 0x1c1000000 ctl 0x1c1000098 irq 32
ata1.00: ATA-0: SMC01GBFK6E, CF080204, max MWDMA2
ata1.00: 2001888 sectors, multi 0: LBA
ata1.00: configured for PIO
ata1.00: configured for PIO
ata1: EH complete
scsi 0:0:0:0: Direct-Access     ATA      SMC01GBFK6E      CF08 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
1fc000000.nor_flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
1fc000000.nor_flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Creating 9 MTD partitions on "1fc000000.nor_flash":
0x00000000-0x00500000 : "kernel0"
0x00500000-0x00a00000 : "ramdisk0"
0x00a00000-0x00f00000 : "kernel1"
0x00f00000-0x01400000 : "ramdisk1"
0x01400000-0x01900000 : "kernel2"
0x01900000-0x01e00000 : "ramdisk2"
0x03f60000-0x03f80000 : "env0"
0x03f80000-0x03fa0000 : "env1"
0x03fa0000-0x04000000 : "u-boot"
spi_ppc4xx_of 1ef600900.spi: driver initialized
ppc-of-ehci e0000300.ehci: OF EHCI
ppc-of-ehci e0000300.ehci: new USB bus registered, assigned bus number 1
ppc-of-ehci e0000300.ehci: irq 34, io mem 0xe0000300
ppc-of-ehci e0000300.ehci: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OF EHCI
usb usb1: Manufacturer: Linux 2.6.27.9-00045-gcccf182-dirty ehci_hcd
usb usb1: SerialNumber: PPC-OF USB
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ppc-of-ohci e0000400.usb: OF OHCI
ppc-of-ohci e0000400.usb: new USB bus registered, assigned bus number 2
ppc-of-ohci e0000400.usb: irq 35, io mem 0xe0000400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OF OHCI
usb usb2: Manufacturer: Linux 2.6.27.9-00045-gcccf182-dirty ohci_hcd
usb usb2: SerialNumber: PPC-OF USB
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
rtc-m41t80 0-0068: chip found, driver version 0.05
rtc-m41t80 0-0068: rtc core: registered m41t65 as rtc0
ibm-iic 1ef600700.i2c: using standard (100 kHz) mode
ibm-iic 1ef600800.i2c: using standard (100 kHz) mode
at24 0-0052: 512 byte 24c04 EEPROM (writable)
ad7414 0-0048: chip found
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-m41t80 0-0068: setting system clock to 2009-01-05 11:33:38 UTC (1231155218)
eth0: link is down
eth0: link is up, 100 FDX, pause enabled
IP-Config: Complete:
     device=eth0, addr=137.237.178.105, mask=255.255.255.0, gw=137.237.178.1,
     host=hydra_temp, domain=, nis-domain=(none),
     bootserver=137.237.179.31, rootserver=137.237.179.31, rootpath=
Freeing unused kernel memory: 156k init
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
$

> Cheers,
> Ben.
> 
>> 	Steve
>>
>>
>> U-Boot 2008.10-00079-gebb3412 (Dec  9 2008 - 16:06:05)
>>
>> CPU:   AMCC PowerPC 440EPx Rev. A at 666.666 MHz (PLB=166, OPB=83, EBC=55 MHz)
>>        Security/Kasumi support
>>        Bootstrap Option H - Boot ROM Location I2C (Addr 0x52)
>>        Internal PCI arbiter enabled, PCI async ext clock used
>>        32 kB I-Cache 32 kB D-Cache
>> Board: Sequoia - AMCC PPC440EPx Evaluation Board, Rev. F, PCI=66 MHz, serial# 7654
>> I2C:   ready
>> SPI:   ready
>> DTT:   1 is 27 C
>> DRAM:  256 MB
>> FLASH: 64 MB
>> NAND:  32 MiB
>> PCI:   Bus Dev VenId DevId Class Int
>>         01  00  1172  0004  ff00  43
>>         00  0c  10b5  8112  0604  43
>> In:    serial
>> Out:   serial
>> Err:   serial
>> RTC:   ready
>> USB:   Host(int phy) Device(ext phy)
>> Net:   ppc_4xx_eth0, ppc_4xx_eth1
>> IDE:   Bus 0: OK
>>   Device 0: PIO mode 4
>> Model: SMC01GBFK6E Firm: CF080204 Ser#: NU0B4000000000102893
>>             Type: Hard Disk
>>             Capacity: 977.4 MB = 0.9 GB (2001888 x 512)
>>
>>
>>
>> ==========================================================
>> |                                                        |
>> |                    Welcome to Hydra                    |
>> |                                                        |
>> ==========================================================
>>
>>
>>
>> Please type "sm" to enter safe-mode.
>>
>>
>> Starting current kernel - please wait.
>> Starting previous kernel - please wait.
>> Starting safe-mode kernel - please wait.
>> ## Booting kernel from Legacy Image at fd400000 ...
>>    Image Name:   Linux-2.6.27.9-00045-gcccf182-di
>>    Created:      2009-01-05  21:29:41 UTC
>>    Image Type:   PowerPC Linux Kernel Image (gzip compressed)
>>    Data Size:    1684167 Bytes =  1.6 MB
>>    Load Address: 00400000
>>    Entry Point:  00400454
>>    Verifying Checksum ... OK
>> ## Loading init Ramdisk from Legacy Image at fd900000 ...
>>    Image Name:   initramfs
>>    Created:      2008-11-26  15:13:12 UTC
>>    Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
>>    Data Size:    2443397 Bytes =  2.3 MB
>>    Load Address: 00000000
>>    Entry Point:  00000000
>>    Verifying Checksum ... OK
>>    Uncompressing Kernel Image ... OK
>>    Loading Ramdisk to 0fcb7000, end 0ff0b885 ... OK
>> CPU clock-frequency <- 0x27bc86a4 (667MHz)
>> CPU timebase-frequency <- 0x27bc86a4 (667MHz)
>> /plb: clock-frequency <- 9ef21a9 (167MHz)
>> /plb/opb: clock-frequency <- 4f790d4 (83MHz)
>> /plb/opb/ebc: clock-frequency <- 34fb5e3 (56MHz)
>> /plb/opb/serial@ef600300: clock-frequency <- a8c000 (11MHz)
>> /plb/opb/serial@ef600400: clock-frequency <- a8c000 (11MHz)
>> /plb/opb/serial@ef600500: clock-frequency <- a8c000 (11MHz)
>> /plb/opb/serial@ef600600: clock-frequency <- a8c000 (11MHz)
>> Memory <- <0x0 0x0 0xffff000> (255MB)
>> ENET0: local-mac-address <- 00:10:ec:01:04:d0
>> ENET1: local-mac-address <- 00:10:ec:01:04:d1
>>
>> zImage starting: loaded at 0x00400000 (sp: 0x0ff0c300)
>> Allocating 0x371974 bytes for kernel ...
>> gunzipping (0x00000000 <- 0x0040f000:0x007ac72c)...done 0x35a1e4 bytes
>> Using loader supplied ramdisk at 0xfcb7000-0xff0b885
>> initrd head: 0x1f8b0808
>>
>> Linux/PowerPC load: root=/dev/sda3 rw ip=137.237.178.105:137.237.179.31:137.237.178.1:255.255.255.0:hydra_temp:eth0:off panic=1 console=ttyS0,115200
>> Finalizing device tree... flat tree at 0x40bf08
>> Using Hydra_temp machine description
>> Linux version 2.6.27.9-00045-gcccf182-dirty (sfalco@saf.cs.myharris.net) (gcc version 4.2.2) #135 Mon Jan 5 16:29:11 EST 2009
>> Found initrd at 0xcfcb7000:0xcff0b885
>> console [udbg0] enabled
>> setup_arch: bootmem
>> arch: exit
>> Zone PFN ranges:
>>   DMA      0x00000000 -> 0x0000ffff
>>   Normal   0x0000ffff -> 0x0000ffff
>> Movable zone start PFN for each node
>> early_node_map[1] active PFN ranges
>>     0: 0x00000000 -> 0x0000ffff
>> Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65023
>> Kernel command line: root=/dev/sda3 rw ip=137.237.178.105:137.237.179.31:137.237.178.1:255.255.255.0:hydra_temp:eth0:off panic=1 console=ttyS0,115200
>> UIC0 (32 IRQ sources) at DCR 0xc0
>> UIC1 (32 IRQ sources) at DCR 0xd0
>> UIC2 (32 IRQ sources) at DCR 0xe0
>> PID hash table entries: 1024 (order: 10, 4096 bytes)
>> clocksource: timebase mult[600000] shift[22] registered
>> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
>> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
>> Memory: 253620k/262140k available (3284k kernel code, 8220k reserved, 124k data, 90k bss, 156k init)
>> SLUB: Genslabs=10, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
>> Calibrating delay loop... 1331.20 BogoMIPS (lpj=2662400)
>> Mount-cache hash table entries: 512
>> net_namespace: 288 bytes
>> NET: Registered protocol family 16
>>
>> PCI host bridge /plb/pci@1ec000000 (primary) ranges:
>>  MEM 0x0000000180000000..0x000000018fffffff -> 0x0000000080000000
>>   IO 0x00000001e8000000..0x00000001e80fffff -> 0x0000000000000000
>> 4xx PCI DMA offset set to 0x00000000
>> PCI: Probing PCI hardware
>> PCI: Hiding 4xx host bridge resources 0000:00:00.0
>> pci 0000:00:0c.0: PME# supported from D0 D1 D3hot
>> pci 0000:00:0c.0: PME# disabled
>> Try to map irq for 0000:00:00.0...
>> pci_busdev_to_OF_node(0,0x0)
>>  parent is /plb/pci@1ec000000
>>  result is <NULL>
>>  -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2
>>  -> mapped to linux irq 16
>> Try to map irq for 0000:00:0c.0...
>> pci_busdev_to_OF_node(0,0x60)
>>  parent is /plb/pci@1ec000000
>>  result is <NULL>
>>  -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2
>>  -> mapped to linux irq 16
>> Try to map irq for 0000:01:00.0...
>> pci_busdev_to_OF_node(1,0x0)
>> pci_busdev_to_OF_node(0,0x60)
>>  parent is /plb/pci@1ec000000
>>  result is <NULL>
>>  -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2
>>  -> mapped to linux irq 16
>> PCI: PHB (bus 0) bridge rsrc 0: 0000000000000000-00000000000fffff [0x100], parent c0339b40 (PCI IO)
>> PCI: PHB (bus 0) bridge rsrc 1: 0000000180000000-000000018fffffff [0x200], parent c0339b18 (PCI mem)
>> PCI: Assigning unassigned resouces...
>> pci 0000:00:0c.0: BAR 8: can't allocate mem resource [0x180000000-0x18fffffff]
>> pci 0000:01:00.0: BAR 1: can't allocate mem resource [0x1f0000000-0x1ffffffff]
>> pci 0000:01:00.0: BAR 0: can't allocate mem resource [0x180000000-0x18007ffff]
>> pci 0000:00:0c.0: PCI bridge, secondary bus 0000:01
>> pci 0000:00:0c.0:   IO window: disabled
>> pci 0000:00:0c.0:   MEM window: disabled
>> pci 0000:00:0c.0:   PREFETCH window: disabled
>> bus: 00 index 0 io port: [0, fffff]
>> bus: 00 index 1 mmio: [180000000, 18fffffff]
>> bus: 01 index 0 mmio: [0, 0]
>> bus: 01 index 1 mmio: [0, 0]
>> bus: 01 index 2 mmio: [0, 0]
>> bus: 01 index 3 mmio: [0, 0]
>> SCSI subsystem initialized
>> usbcore: registered new interface driver usbfs
>> usbcore: registered new interface driver hub
>> usbcore: registered new device driver usb
>> NET: Registered protocol family 2
>> IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
>> TCP established hash table entries: 8192 (order: 4, 65536 bytes)
>> TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
>> TCP: Hash tables configured (established 8192 bind 8192)
>> TCP reno registered
>> NET: Registered protocol family 1
>> checking if image is initramfs... it is
>> Freeing initrd memory: 2386k freed
>> msgmni has been set to 500
>> io scheduler noop registered
>> io scheduler anticipatory registered (default)
>> io scheduler deadline registered
>> io scheduler cfq registered
>> Serial: 8250/16550 driver4 ports, IRQ sharing enabled
>> serial8250.0: ttyS0 at MMIO 0x1ef600300 (irq = 17) is a 16550A
>>                                                               console handover: boot [udbg0] -> real [ttyS0]
>> serial8250.0: ttyS1 at MMIO 0x1ef600400 (irq = 18) is a 16550A
>> serial8250.0: ttyS2 at MMIO 0x1ef600500 (irq = 19) is a 16550A
>> serial8250.0: ttyS3 at MMIO 0x1ef600600 (irq = 20) is a 16550A
>> 1ef600300.serial: ttyS0 at MMIO 0x1ef600300 (irq = 17) is a 16550A
>> 1ef600400.serial: ttyS1 at MMIO 0x1ef600400 (irq = 18) is a 16550A
>> 1ef600500.serial: ttyS2 at MMIO 0x1ef600500 (irq = 19) is a 16550A
>> 1ef600600.serial: ttyS3 at MMIO 0x1ef600600 (irq = 20) is a 16550A
>> brd: module loaded
>> PPC 4xx OCP EMAC driver, version 3.54
>> MAL v2 /plb/mcmal, 2 TX channels, 2 RX channels
>> ZMII /plb/opb/emac-zmii@ef600d00 initialized
>> RGMII /plb/opb/emac-rgmii@ef601000 initialized with MDIO support
>> /plb/opb/emac-rgmii@ef601000: input 0 in RGMII mode
>> eth0: EMAC-0 /plb/opb/ethernet@ef600e00, MAC 00:10:ec:01:04:d0
>> eth0: found Marvell 88E1111 Ethernet PHY (0x00)
>> /plb/opb/emac-rgmii@ef601000: input 1 in RGMII mode
>> eth1: EMAC-1 /plb/opb/ethernet@ef600f00, MAC 00:10:ec:01:04:d1
>> eth1: found Marvell 88E1111 Ethernet PHY (0x01)
>> Uniform Multi-Platform E-IDE driver
>> Driver 'sd' needs updating - please use bus_type methods
>> scsi0 : pata_platform
>> ata1: PATA max PIO6 mmio cmd 0x1c1000000 ctl 0x1c1000098 irq 32
>> ata1.00: ATA-0: SMC01GBFK6E, CF080204, max MWDMA2
>> ata1.00: 2001888 sectors, multi 0: LBA
>> ata1.00: configured for PIO
>> ata1.00: configured for PIO
>> ata1: EH complete
>> scsi 0:0:0:0: Direct-Access     ATA      SMC01GBFK6E      CF08 PQ: 0 ANSI: 5
>> sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB)
>> sd 0:0:0:0: [sda] Write Protect is off
>> sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
>> sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB)
>> sd 0:0:0:0: [sda] Write Protect is off
>> sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
>>  sda: sda1 sda2 sda3 sda4
>> sd 0:0:0:0: [sda] Attached SCSI disk
>> sd 0:0:0:0: Attached scsi generic sg0 type 0
>> 1fc000000.nor_flash: Found 1 x16 devices at 0x0 in 16-bit bank
>>  Amd/Fujitsu Extended Query Table at 0x0040
>> 1fc000000.nor_flash: CFI does not contain boot bank location. Assuming top.
>> number of CFI chips: 1
>> cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
>> RedBoot partition parsing not available
>> Creating 9 MTD partitions on "1fc000000.nor_flash":
>> 0x00000000-0x00500000 : "kernel0"
>> 0x00500000-0x00a00000 : "ramdisk0"
>> 0x00a00000-0x00f00000 : "kernel1"
>> 0x00f00000-0x01400000 : "ramdisk1"
>> 0x01400000-0x01900000 : "kernel2"
>> 0x01900000-0x01e00000 : "ramdisk2"
>> 0x03f60000-0x03f80000 : "env0"
>> 0x03f80000-0x03fa0000 : "env1"
>> 0x03fa0000-0x04000000 : "u-boot"
>> spi_ppc4xx_of 1ef600900.spi: driver initialized
>> ppc-of-ehci e0000300.ehci: OF EHCI
>> ppc-of-ehci e0000300.ehci: new USB bus registered, assigned bus number 1
>> ppc-of-ehci e0000300.ehci: irq 34, io mem 0xe0000300
>> ppc-of-ehci e0000300.ehci: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
>> usb usb1: configuration #1 chosen from 1 choice
>> hub 1-0:1.0: USB hub found
>> hub 1-0:1.0: 1 port detected
>> usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
>> usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>> usb usb1: Product: OF EHCI
>> usb usb1: Manufacturer: Linux 2.6.27.9-00045-gcccf182-dirty ehci_hcd
>> usb usb1: SerialNumber: PPC-OF USB
>> ppc-of-ohci e0000400.usb: OF OHCI
>> ppc-of-ohci e0000400.usb: new USB bus registered, assigned bus number 2
>> ppc-of-ohci e0000400.usb: irq 35, io mem 0xe0000400
>> usb usb2: configuration #1 chosen from 1 choice
>> hub 2-0:1.0: USB hub found
>> hub 2-0:1.0: 1 port detected
>> usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
>> usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>> usb usb2: Product: OF OHCI
>> usb usb2: Manufacturer: Linux 2.6.27.9-00045-gcccf182-dirty ohci_hcd
>> usb usb2: SerialNumber: PPC-OF USB
>> Initializing USB Mass Storage driver...
>> usbcore: registered new interface driver usb-storage
>> USB Mass Storage support registered.
>> i2c /dev entries driver
>> rtc-m41t80 0-0068: chip found, driver version 0.05
>> rtc-m41t80 0-0068: rtc core: registered m41t65 as rtc0
>> ibm-iic 1ef600700.i2c: using standard (100 kHz) mode
>> ibm-iic 1ef600800.i2c: using standard (100 kHz) mode
>> at24 0-0052: 512 byte 24c04 EEPROM (writable)
>> ad7414 0-0048: chip found
>> TCP cubic registered
>> NET: Registered protocol family 17
>> RPC: Registered udp transport module.
>> RPC: Registered tcp transport module.
>> rtc-m41t80 0-0068: setting system clock to 2009-01-05 11:33:38 UTC (1231155218)
>> eth0: link is down
>> eth0: link is up, 100 FDX, pause enabled
>> IP-Config: Complete:
>>      device=eth0, addr=137.237.178.105, mask=255.255.255.0, gw=137.237.178.1,
>>      host=hydra_temp, domain=, nis-domain=(none),
>>      bootserver=137.237.179.31, rootserver=137.237.179.31, rootpath=
>> Freeing unused kernel memory: 156k init
>> Checking /dev/sda1
>> Checking /dev/sda2
>> Checking /dev/sda3
>> Checking /dev/sda4
>> kjournald starting.  Commit interval 5 seconds
>> EXT3 FS on sda3, internal journal
>> EXT3-fs: mounted filesystem with ordered data mode.
>> kjournald starting.  Commit interval 5 seconds
>> EXT3 FS on sda1, internal journal
>> EXT3-fs: mounted filesystem with ordered data mode.
>> kjournald starting.  Commit interval 5 seconds
>> EXT3 FS on sda2, internal journal
>> EXT3-fs: mounted filesystem with ordered data mode.
>> kjournald starting.  Commit interval 5 seconds
>> EXT3 FS on sda4, internal journal
>> EXT3-fs: mounted filesystem with ordered data mode.
>> init started: BusyBox v1.10.4 (2008-10-27 12:52:02 EDT)
>> starting pid 889, tty '/dev/ttyS0': '/etc/init.d/rcS'
>> launcher[944]: launching /bin/craft on /dev/ttyS0
>> Hydra>
> 
> 

Re: [QUESTION] 440EPx with PCI to PCIe bridge error

[Steven A. Falco]

Benjamin Herrenschmidt wrote:
> 
>> Here is a complete startup log, with debug turned on as you requested.
>> This is still against 2.6.27.9, as it will take me a little time to
>> build 2.6.28.  Hopefully, this log will be useful in the meantime.
> 
> Can you add "debug" to your kernel command line option or send the
> output of the "dmesg" command please ?
> 
> Cheers,
> Ben.

I've repeated the experiment with 2.6.28.  There is no improvement; I'm
still getting the "can't allocate mem resource" messages.

I've included the log below, with debug turned on in the specific pci
files you mentioned, and with the debug flag passed to the kernel.  At
the end of the log, I did an lspci, and also looked at /sys/bus/pci.
As you will see, the resources are all zero.

I can also try again with one of the "master" or "next" trees.  If you
think that would be helpful, just let me know what tree you would like
me to try.

Thanks again for helping with this.

	Steve


=> run flash_self;setenv bootargs ${bootargs} debug;bootm fd400000 fd900000
## Booting kernel from Legacy Image at fd400000 ...
   Image Name:   Linux-2.6.28-00013-ge007bf7-dirt
   Created:      2009-01-06  18:22:31 UTC
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1749398 Bytes =  1.7 MB
   Load Address: 00400000
   Entry Point:  0040045c
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at fd900000 ...
   Image Name:   initramfs
   Created:      2008-11-26  15:13:12 UTC
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    2443397 Bytes =  2.3 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
   Loading Ramdisk to 0fcb7000, end 0ff0b885 ... OK
CPU clock-frequency <- 0x27bc86a4 (667MHz)
CPU timebase-frequency <- 0x27bc86a4 (667MHz)
/plb: clock-frequency <- 9ef21a9 (167MHz)
/plb/opb: clock-frequency <- 4f790d4 (83MHz)
/plb/opb/ebc: clock-frequency <- 34fb5e3 (56MHz)
/plb/opb/serial@ef600300: clock-frequency <- a8c000 (11MHz)
/plb/opb/serial@ef600400: clock-frequency <- a8c000 (11MHz)
/plb/opb/serial@ef600500: clock-frequency <- a8c000 (11MHz)
/plb/opb/serial@ef600600: clock-frequency <- a8c000 (11MHz)
Memory <- <0x0 0x0 0xffff000> (255MB)
ENET0: local-mac-address <- 00:10:ec:01:04:d0
ENET1: local-mac-address <- 00:10:ec:01:04:d1

zImage starting: loaded at 0x00400000 (sp: 0x0ff0c828)
Allocating 0x3903b0 bytes for kernel ...
gunzipping (0x00000000 <- 0x0040f000:0x007ca920)...done 0x3781fc bytes
Using loader supplied ramdisk at 0xfcb7000-0xff0b885
initrd head: 0x1f8b0808

Linux/PowerPC load: root=/dev/sda3 rw loglevel=7 ip=137.237.178.105:137.237.179.31:137.237.178.1:255.255.255.0:hydra_temp:eth0:off panic=1 console=ttyS0,115200 debug
Finalizing device tree... flat tree at 0x7d7300
Using Hydra_temp machine description
Linux version 2.6.28-00013-ge007bf7-dirty (sfalco@saf.cs.myharris.net) (gcc version 4.2.2) #138 Tue Jan 6 13:22:15 EST 2009
Found initrd at 0xcfcb7000:0xcff0b885
Found legacy serial port 0 for /plb/opb/serial@ef600300
  mem=1ef600300, taddr=1ef600300, irq=0, clk=11059200, speed=115200
Found legacy serial port 1 for /plb/opb/serial@ef600400
  mem=1ef600400, taddr=1ef600400, irq=0, clk=11059200, speed=0
Found legacy serial port 2 for /plb/opb/serial@ef600500
  mem=1ef600500, taddr=1ef600500, irq=0, clk=11059200, speed=0
Found legacy serial port 3 for /plb/opb/serial@ef600600
  mem=1ef600600, taddr=1ef600600, irq=0, clk=11059200, speed=0
console [udbg0] enabled
setup_arch: bootmem
arch: exit
Top of RAM: 0xffff000, Total RAM: 0xffff000
Memory hole size: 0MB
Zone PFN ranges:
  DMA      0x00000000 -> 0x0000ffff
  Normal   0x0000ffff -> 0x0000ffff
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x0000ffff
On node 0 totalpages: 65535
free_area_init_node: node 0, pgdat c037077c, node_mem_map c0391000
  DMA zone: 512 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 65023 pages, LIFO batch:15
  Normal zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65023
Kernel command line: root=/dev/sda3 rw loglevel=7 ip=137.237.178.105:137.237.179.31:137.237.178.1:255.255.255.0:hydra_temp:eth0:off panic=1 console=ttyS0,115200 debug
UIC0 (32 IRQ sources) at DCR 0xc0
UIC1 (32 IRQ sources) at DCR 0xd0
UIC2 (32 IRQ sources) at DCR 0xe0
PID hash table entries: 1024 (order: 10, 4096 bytes)
time_init: decrementer frequency = 666.666660 MHz
time_init: processor frequency   = 666.666660 MHz
clocksource: timebase mult[600000] shift[22] registered
clockevent: decrementer mult[aaaa] shift[16] cpu[0]
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 253492k/262140k available (3380k kernel code, 8340k reserved, 148k data, 92k bss, 160k init)
SLUB: Genslabs=10, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 1331.20 BogoMIPS (lpj=2662400)
Mount-cache hash table entries: 512
net_namespace: 288 bytes
NET: Registered protocol family 16

PCI host bridge /plb/pci@1ec000000 (primary) ranges:
 MEM 0x0000000180000000..0x000000018fffffff -> 0x0000000080000000
  IO 0x00000001e8000000..0x00000001e80fffff -> 0x0000000000000000
4xx PCI DMA offset set to 0x00000000
PCI: Probing PCI hardware
pci 0000:00:00.0: reg 14 32bit mmio: [0x000000-0x7fffffff]
PCI:0000:00:00.0 Resource 1 0000000000000000-000000007fffffff [21208] is unassigned
PCI: Hiding 4xx host bridge resources 0000:00:00.0
pci 0000:00:00.0: supports D1
pci 0000:00:0c.0: supports D1
pci 0000:00:0c.0: PME# supported from D0 D1 D3hot
pci 0000:00:0c.0: PME# disabled
PCI: Fixup bus 0 (PHB)
pci_busdev_to_OF_node(0,0x0)
 parent is /plb/pci@1ec000000
 result is <NULL>
PCI: device 0000:00:00.0 OF node: <none>
pci_busdev_to_OF_node(0,0x60)
 parent is /plb/pci@1ec000000
 result is <NULL>
PCI: device 0000:00:0c.0 OF node: <none>
Try to map irq for 0000:00:00.0...
pci_busdev_to_OF_node(0,0x0)
 parent is /plb/pci@1ec000000
 result is <NULL>
 -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2
 -> mapped to linux irq 16
Try to map irq for 0000:00:0c.0...
pci_busdev_to_OF_node(0,0x60)
 parent is /plb/pci@1ec000000
 result is <NULL>
 -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2
 -> mapped to linux irq 16
pci 0000:01:00.0: reg 10 32bit mmio: [0x80000000-0x8007ffff]
pci 0000:01:00.0: reg 14 32bit mmio: [0xf0000000-0xffffffff]
PCI:0000:01:00.0 Resource 0 0000000080000000-000000008007ffff [20200] fixup...
PCI:0000:01:00.0            0000000180000000-000000018007ffff
PCI:0000:01:00.0 Resource 1 00000000f0000000-00000000ffffffff [20200] fixup...
PCI:0000:01:00.0            00000001f0000000-00000001ffffffff
pci 0000:00:0c.0: bridge 32bit mmio: [0x80000000-0x800fffff]
PCI: Fixup bus 1 (0000:00:0c.0)
PCI:0000:00:0c.0 Bus rsrc 1 0000000080000000-00000000800fffff [200] fixup...
PCI:0000:00:0c.0            0000000180000000-00000001800fffff
pci_busdev_to_OF_node(1,0x0)
PCI: device 0000:01:00.0 OF node: <none>
Try to map irq for 0000:01:00.0...
pci_busdev_to_OF_node(1,0x0)
pci_busdev_to_OF_node(0,0x60)
 parent is /plb/pci@1ec000000
 result is <NULL>
 -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2
 -> mapped to linux irq 16
PCI: PHB (bus 0) bridge rsrc 0: 0000000000000000-00000000000fffff [0x100], parent c0351c80 (PCI IO)
PCI: PHB (bus 0) bridge rsrc 1: 0000000180000000-000000018fffffff [0x200], parent c0351c58 (PCI mem)
PCI: Assigning unassigned resouces...
pci 0000:00:0c.0: BAR 8: can't allocate mem resource [0x180000000-0x18fffffff]
pci 0000:01:00.0: BAR 1: can't allocate mem resource [0x1f0000000-0x1ffffffff]
pci 0000:01:00.0: BAR 0: can't allocate mem resource [0x180000000-0x18007ffff]
pci 0000:00:0c.0: PCI bridge, secondary bus 0000:01
pci 0000:00:0c.0:   IO window: disabled
pci 0000:00:0c.0:   MEM window: disabled
pci 0000:00:0c.0:   PREFETCH window: disabled
bus: 00 index 0 io port: [0x00-0xfffff]
bus: 00 index 1 mmio: [0x180000000-0x18fffffff]
bus: 01 index 0 mmio: [0x0-0x0]
bus: 01 index 1 mmio: [0x0-0x0]
bus: 01 index 2 mmio: [0x0-0x0]
bus: 01 index 3 mmio: [0x0-0x0]
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Switched to high resolution mode on CPU 0
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Freeing initrd memory: 2386k freed
msgmni has been set to 500
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x1ef600300 (irq = 17) is a 16550A
console handover: boot [udbg0] -> real [ttyS0]
serial8250.0: ttyS1 at MMIO 0x1ef600400 (irq = 18) is a 16550A
serial8250.0: ttyS2 at MMIO 0x1ef600500 (irq = 19) is a 16550A
serial8250.0: ttyS3 at MMIO 0x1ef600600 (irq = 20) is a 16550A
1ef600300.serial: ttyS0 at MMIO 0x1ef600300 (irq = 17) is a 16550A
1ef600400.serial: ttyS1 at MMIO 0x1ef600400 (irq = 18) is a 16550A
1ef600500.serial: ttyS2 at MMIO 0x1ef600500 (irq = 19) is a 16550A
1ef600600.serial: ttyS3 at MMIO 0x1ef600600 (irq = 20) is a 16550A
brd: module loaded
PPC 4xx OCP EMAC driver, version 3.54
MAL v2 /plb/mcmal, 2 TX channels, 2 RX channels
ZMII /plb/opb/emac-zmii@ef600d00 initialized
RGMII /plb/opb/emac-rgmii@ef601000 initialized with MDIO support
/plb/opb/emac-rgmii@ef601000: input 0 in RGMII mode
eth0: EMAC-0 /plb/opb/ethernet@ef600e00, MAC 00:10:ec:01:04:d0
eth0: found Marvell 88E1111 Ethernet PHY (0x00)
/plb/opb/emac-rgmii@ef601000: input 1 in RGMII mode
eth1: EMAC-1 /plb/opb/ethernet@ef600f00, MAC 00:10:ec:01:04:d1
eth1: found Marvell 88E1111 Ethernet PHY (0x01)
Uniform Multi-Platform E-IDE driver
ide-gd driver 1.18
Driver 'sd' needs updating - please use bus_type methods
scsi0 : pata_platform
ata1: PATA max PIO6 mmio cmd 0x1c1000000 ctl 0x1c1000098 irq 32
ata1.00: ATA-0: SMC01GBFK6E, CF080204, max MWDMA2
ata1.00: 2001888 sectors, multi 0: LBA
ata1.00: configured for PIO
ata1.00: configured for PIO
ata1: EH complete
scsi 0:0:0:0: Direct-Access     ATA      SMC01GBFK6E      CF08 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors: (1.02 GB/977 MiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors: (1.02 GB/977 MiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
1fc000000.nor_flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
1fc000000.nor_flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Creating 9 MTD partitions on "1fc000000.nor_flash":
0x00000000-0x00500000 : "kernel0"
0x00500000-0x00a00000 : "ramdisk0"
0x00a00000-0x00f00000 : "kernel1"
0x00f00000-0x01400000 : "ramdisk1"
0x01400000-0x01900000 : "kernel2"
0x01900000-0x01e00000 : "ramdisk2"
0x03f60000-0x03f80000 : "env0"
0x03f80000-0x03fa0000 : "env1"
0x03fa0000-0x04000000 : "u-boot"
spi_ppc4xx_of 1ef600900.spi: driver initialized
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ppc-of-ehci e0000300.ehci: OF EHCI
ppc-of-ehci e0000300.ehci: new USB bus registered, assigned bus number 1
ppc-of-ehci e0000300.ehci: irq 34, io mem 0xe0000300
ppc-of-ehci e0000300.ehci: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OF EHCI
usb usb1: Manufacturer: Linux 2.6.28-00013-ge007bf7-dirty ehci_hcd
usb usb1: SerialNumber: PPC-OF USB
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ppc-of-ohci e0000400.usb: OF OHCI
ppc-of-ohci e0000400.usb: new USB bus registered, assigned bus number 2
ppc-of-ohci e0000400.usb: irq 35, io mem 0xe0000400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OF OHCI
usb usb2: Manufacturer: Linux 2.6.28-00013-ge007bf7-dirty ohci_hcd
usb usb2: SerialNumber: PPC-OF USB
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
rtc-m41t80 0-0068: chip found, driver version 0.05
rtc-m41t80 0-0068: rtc core: registered m41t65 as rtc0
ibm-iic 1ef600700.i2c: using standard (100 kHz) mode
ibm-iic 1ef600800.i2c: using standard (100 kHz) mode
at24 0-0052: 512 byte 24c04 EEPROM (writable)
ad7414 0-0048: chip found
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-m41t80 0-0068: setting system clock to 2009-01-06 08:26:29 UTC (1231230389)
eth0: link is down
eth0: link is up, 100 FDX, pause enabled
IP-Config: Complete:
     device=eth0, addr=137.237.178.105, mask=255.255.255.0, gw=137.237.178.1,
     host=hydra_temp, domain=, nis-domain=(none),
     bootserver=137.237.179.31, rootserver=137.237.179.31, rootpath=
Freeing unused kernel memory: 160k init
Checking /dev/sda1
Checking /dev/sda2
Checking /dev/sda3
Checking /dev/sda4
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
init started: BusyBox v1.10.4 (2008-10-27 12:52:02 EDT)
starting pid 912, tty '/dev/ttyS0': '/etc/init.d/rcS'
launcher[970]: launching /bin/craft on /dev/ttyS0
Hydra> !
$ su
Password:
# lspci
00:00.0 Class 0680: Unknown device 1014:027f
00:0c.0 Class 0604: Unknown device 10b5:8112 (rev aa)
01:00.0 Class ff00: Unknown device 1172:0004 (rev 01)
# ls /sys/bus/pci/devices/*
/sys/bus/pci/devices/0000:00:00.0:
broken_parity_status  enable                resource
bus                   irq                   subsystem
class                 local_cpulist         subsystem_device
config                local_cpus            subsystem_vendor
device                modalias              uevent
devspec               msi_bus               vendor

/sys/bus/pci/devices/0000:00:0c.0:
0000:01:00.0          enable                resource
broken_parity_status  irq                   subsystem
bus                   local_cpulist         subsystem_device
class                 local_cpus            subsystem_vendor
config                modalias              uevent
device                msi_bus               vendor
devspec               pci_bus:0000:01

/sys/bus/pci/devices/0000:01:00.0:
broken_parity_status  enable                resource
bus                   irq                   subsystem
class                 local_cpulist         subsystem_device
config                local_cpus            subsystem_vendor
device                modalias              uevent
devspec               msi_bus               vendor
# cat /sys/bus/pci/devices/0000:00:0c.0/resource
0x0000000000000000 0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000 0x0000000000000000
# cat /sys/bus/pci/devices/0000:01:00.0/resource
0x0000000000000000 0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000 0x0000000000000000
#

Re: [QUESTION] 440EPx with PCI to PCIe bridge error

[Steven A. Falco]

Benjamin Herrenschmidt wrote:
> 
>> Here is a complete startup log, with debug turned on as you requested.
>> This is still against 2.6.27.9, as it will take me a little time to
>> build 2.6.28.  Hopefully, this log will be useful in the meantime.
> 
> Can you add "debug" to your kernel command line option or send the
> output of the "dmesg" command please ?
> 
> Cheers,
> Ben.
> 

I saw a recent post from Anton talking about U-Boot configuring PCI.  That
got me wondering if U-Boot has anything to do with the problem I've
reported.  So, I turned on debug in uboot's pci_auto.c, and added another
DEBUGF like so:

	if (addr - res->bus_start + size > res->size) {
		DEBUGF("address=0x%lx bus_start=%lx size=%x limit=%lx\n",
			       	addr, res->bus_start, size, res->size);
		DEBUGF("No room in resource");
		goto error;
	}

When starting U-Boot, I get a "No room in resource" message.  Will this
affect Linux, or is it just a U-Boot warning?

	Steve


U-Boot 2008.10-00079-gebb3412-dirty (Jan  6 2009 - 15:21:56)

CPU:   AMCC PowerPC 440EPx Rev. A at 666.666 MHz (PLB=166, OPB=83, EBC=55 MHz)
       Security/Kasumi support
       Bootstrap Option H - Boot ROM Location I2C (Addr 0x52)
       Internal PCI arbiter enabled, PCI async ext clock used
       32 kB I-Cache 32 kB D-Cache
Board: Sequoia - AMCC PPC440EPx Evaluation Board, Rev. F, PCI=66 MHz, serial# 7654
I2C:   ready
SPI:   ready
DTT:   1 is 35 C
DRAM:  256 MB
FLASH: 64 MB
NAND:  32 MiB
PCI:   Bus Dev VenId DevId Class Int
PCI Autoconfig: Bus Memory region: [80000000-8fffffff],
                Physical Memory [80000000-8fffffff]
PCI Autoconfig: Bus I/O region: [0-ffff],
                Physical Memory: [e8000000-e800ffff]
PCI Autoconfig: Found P2P bridge, device 12
PCI Autoconfig: BAR 0, Mem, size=0x80000, address=0x80000000 bus_lower=80080000
PCI Autoconfig: BAR 1, Mem, size=0x10000000, address=0x90000000 bus_start=80000000 size=10000000 limit=10000000
No room in resource
        01  00  1172  0004  ff00  43
        00  0c  10b5  8112  0604  43

Re: [QUESTION] 440EPx with PCI to PCIe bridge error

[Steven A. Falco]

Steven A. Falco wrote:
> Benjamin Herrenschmidt wrote:
>>> Here is a complete startup log, with debug turned on as you requested.
>>> This is still against 2.6.27.9, as it will take me a little time to
>>> build 2.6.28.  Hopefully, this log will be useful in the meantime.
>> Can you add "debug" to your kernel command line option or send the
>> output of the "dmesg" command please ?
>>

Time to answer my own questions.  U-boot is missing a setting for
CFG_PCI_MEMSIZE in the sequoia.h file.  Four 256MB TLBs are reserved,
but since CFG_PCI_MEMSIZE is not set, the size defaults to 256MB,
rather than the 1GB that is allocated.

So, I added:

#define CFG_PCI_MEMSIZE 0x40000000 /* 1GB */

to sequoia.h.  Now U-boot uses all four TLBs, and that error message
goes away.

But this has no effect on Linux.  So, I also changed the sequoia.dts
to make the outbound range larger, and now Linux is happy too.  I now
have ranges for the device:

# cat 0000:01:00.0/resource
0x0000000190000000 0x000000019007ffff 0x0000000000020200
0x0000000180000000 0x000000018fffffff 0x0000000000020200

	Steve

Re: [QUESTION] 440EPx with PCI to PCIe bridge error

[Benjamin Herrenschmidt]

On Tue, 2009-01-06 at 16:38 -0500, Steven A. Falco wrote:
> But this has no effect on Linux.  So, I also changed the sequoia.dts
> to make the outbound range larger, and now Linux is happy too.  I now
> have ranges for the device:
> 
> # cat 0000:01:00.0/resource
> 0x0000000190000000 0x000000019007ffff 0x0000000000020200
> 0x0000000180000000 0x000000018fffffff 0x0000000000020200

So your problem is fixed ? I didn't have a chance yet to look at your
logs, but it could just have been that you didn't have enough space
allocated to PCI for your card...

Cheers,
Ben.

Re: [QUESTION] 440EPx with PCI to PCIe bridge error

[Steven A. Falco]

Benjamin Herrenschmidt wrote:
> On Tue, 2009-01-06 at 16:38 -0500, Steven A. Falco wrote:
>> But this has no effect on Linux.  So, I also changed the sequoia.dts
>> to make the outbound range larger, and now Linux is happy too.  I now
>> have ranges for the device:
>>
>> # cat 0000:01:00.0/resource
>> 0x0000000190000000 0x000000019007ffff 0x0000000000020200
>> 0x0000000180000000 0x000000018fffffff 0x0000000000020200
> 
> So your problem is fixed ? I didn't have a chance yet to look at your
> logs, but it could just have been that you didn't have enough space
> allocated to PCI for your card...
> 
> Cheers,
> Ben.

That appears to be the problem.  Apparently the PCI/PCIe bridge requests
in excess of 256 MB of space, but the default in the sequoia .dts file is
"only" for 256 MB, so the request fails.

I'm not sure if this should be changed in the mainline.  This card works
out of the box when used with a generic x86 PC, but not when used with
a sequoia.  But, maybe it's just me climbing the PPC learning curve.

	Steve

Re: [QUESTION] 440EPx with PCI to PCIe bridge error

[Benjamin Herrenschmidt]

> I'm not sure if this should be changed in the mainline.  This card works
> out of the box when used with a generic x86 PC, but not when used with
> a sequoia.  But, maybe it's just me climbing the PPC learning curve.

Nah, I think 256M is ridiculously small :-) I think the .dts for that
board should be changed, there is plenty of physical address space
available on those chips since it's using a 36-bit bus.

Cheers,
Ben.
 

Re: [QUESTION] 440EPx with PCI to PCIe bridge error

[Steven A. Falco]

Benjamin Herrenschmidt wrote:
> 
>> I'm not sure if this should be changed in the mainline.  This card works
>> out of the box when used with a generic x86 PC, but not when used with
>> a sequoia.  But, maybe it's just me climbing the PPC learning curve.
> 
> Nah, I think 256M is ridiculously small :-) I think the .dts for that
> board should be changed, there is plenty of physical address space
> available on those chips since it's using a 36-bit bus.
> 
> Cheers,
> Ben.
>  

Sheepish grin:  I did more checking, and the current mainline actually has
this set to 1 GB.

The .dts I'm using dates back to 2.6.25.  I had started modifying it for some
custom peripherals we have hacked onto a Sequoia, and I missed the changes
that were made between .25 and .28.

If you think 1 GB is a suitable default, then no further changes are needed.
If you think it should be bigger than 1 GB, then I could submit a patch.

	Steve

Re: [QUESTION] 440EPx with PCI to PCIe bridge error

[Benjamin Herrenschmidt]

On Wed, 2009-01-07 at 09:45 -0500, Steven A. Falco wrote:
> 
> If you think 1 GB is a suitable default, then no further changes are needed.
> If you think it should be bigger than 1 GB, then I could submit a patch.

Depends how many PCI busses thing thing have... 1GB should get most
people going tho.

Cheers,
Ben.