Re: Gianfar driver crashes in Kernel v3.10

[Claudiu Manoil <claudiu.manoil@freescale.com>]

On 10/11/2013 12:41 AM, Scott Wood wrote:
> On Thu, 2013-10-10 at 14:07 +0300, Claudiu Manoil wrote:
>> On 10/4/2013 3:28 PM, Thomas H=C3=BChn wrote:
>>>
>>> [code]
>>> [ 2671.841927] Oops: Exception in kernel mode, sig: 5 [#1]
>>> [ 2671.847141] Freescale P1014
>>> [ 2671.849925] Modules linked in: ath9k pppoe ppp_async iptable_nat
>>> ath9k_common pppox p
>>> e xt_tcpudp xt_tcpmss xt_string xt_statistic xt_state xt_recent xt_qu=
ota
>>> xt_pkttype xt_o
>>> mark xt_connbytes xt_comment xt_addrtype xt_TCPMSS xt_REDIRECT xt_NET=
MAP
>>> xt_LOG xt_IPMAR
>>> ms_datafab ums_cypress ums_alauda slhc nf_nat_tftp nf_nat_snmp_basic
>>> nf_nat_sip nf_nat_r
>>> ntrack_sip nf_conntrack_rtsp nf_conntrack_proto_gre nf_conntrack_irc
>>> nf_conntrack_h323 n
>>> compat_xtables compat ath sch_teql sch_tbf sch_sfq sch_red sch_prio
>>> sch_htb sch_gred sc
>>> skbedit act_mirred em_u32 cls_u32 cls_tcindex cls_flow cls_route cls_=
fw
>>> sch_hfsc sch_ing
>>> r usb_storage leds_gpio ohci_hcd ehci_platform ehci_hcd sd_mod scsi_m=
od
>>> fsl_mph_dr_of gp
>>> [ 2671.988946] CPU: 0 PID: 5209 Comm: iftop Not tainted 3.10.13 #2
>>> [ 2671.994859] task: c4b22220 ti: c7ff8000 task.ti: c477e000
>>> [ 2672.000250] NIP: c018c7a0 LR: c018c794 CTR: c000b070
>>> [ 2672.005206] REGS: c7ff9f10 TRAP: 3202   Not tainted  (3.10.13)
>>> [ 2672.011028] MSR: 00029000 <CE,EE,ME>  CR: 48000024  XER: 20000000
>>> [ 2672.017125]
>>> GPR00: 000000ff c477fde0 c4b22220 00000000 00000000 000000ff 00000000
>>> 70000000
>>> GPR08: ffffffff 00000008 00000000 ffffffff 00000046 10022248 00000000
>>> 00000008
>>> GPR16: c781b3c0 c781b3c0 000000ff 00000000 00000001 0000021c 00000086
>>> fffff800
>>> GPR24: c7980300 00000000 00000001 00000040 00000003 c4b33000 00000000
>>> 00000001
>>> [ 2672.046832] NIP [c018c7a0] gfar_poll+0x424/0x520
>>> [ 2672.051442] LR [c018c794] gfar_poll+0x418/0x520
>>> [ 2672.055962] Call Trace:
>>> [ 2672.058402] [c477fde0] [c018c674] gfar_poll+0x2f8/0x520 (unreliabl=
e)
>>> [ 2672.064762] [c477fe80] [c01b0ce8] net_rx_action+0x6c/0x158
>>> [ 2672.070249] [c477feb0] [c0027dc4] __do_softirq+0xbc/0x16c
>>> [ 2672.075642] [c477ff00] [c0027f7c] irq_exit+0x4c/0x68
>>> [ 2672.080604] [c477ff10] [c00041f8] do_IRQ+0xf4/0x10c
>>> [ 2672.085478] [c477ff40] [c000ca3c] ret_from_except+0x0/0x18
>>> [ 2672.090991] --- Exception: 501 at 0x48083c28
>>> [ 2672.090991]     LR =3D 0x48083bf8
>>> [ 2672.098378] Instruction dump:
>>> [ 2672.101338] 7f8f2040 419cfcc4 80900000 38a00000 8061004c 7e118378
>>> 81c10050 7ffafb78
>>> [ 2672.109092] 4bf9eaa1 83810034 7c7e1b78 8361003c <83210038> 83a1004=
c
>>> 48000060 41a2004c
>>> [ 2672.117021] ---[ end trace 565fb54528d305fa ]---
>>> [ 2672.121628]
>>> [ 2673.103130] Kernel panic - not syncing: Fatal exception in interru=
pt
>>> [ 2673.109474] Rebooting in 3 seconds..
>>>
>>> U-Boot 2010.12-svn15934 (Dec 11 2012 - 16:23:49)
>>> [/code]
>>>
>>
>> Hi,
>>
>> Does this show up on a half duplex (100Mb/s) link?
>> Could you provide following for the gianfar interface, on your setup:
>> # ethtool ethX
>> and
>> # ethtool -d ethX | grep 500
>>
>> Is there any other indication before this Oops? Like a tx timeout WARN=
?
>
> It's a watchdog interrupt (CPU watchdog, not netdev).  I think it's onl=
y
> showing up in the gianfar code because that's what's running (unless th=
e
> gianfar code is causing the watchdog daemon to not run).
>

Hi Scott,
Good to know that the exception is triggered by the watchdog, and at
this point I assume they simply enabled the watchdog support in kernel
(as you know, it's not enabled by the default config) and that the
exception triggered as the system froze.  Since this reportedly happens
under certain traffic conditions (not "high network load, or routing
traffic") I think that information about the link state (whether
it's 100 Mb/s half duplex or not) is relevant here.  Any other
indication on top of that (if there is any) is also useful.

Thanks.

Claudiu