* Question about EHCI on P4080
@ 2014-02-20 5:55 Ruchika
2014-02-20 18:56 ` Ruchika
0 siblings, 1 reply; 3+ messages in thread
From: Ruchika @ 2014-02-20 5:55 UTC (permalink / raw)
To: linuxppc-dev
Hi,
I've been trying to understand why the uboot code is unable to work with
USB1.1 devices.
On a USB analyzer:
I notice on an analyzer that there are no SOF or IN tokens seen on the
bus at all. The only after the very first setup packet is sent and ACK'd.
The board has a hub chip on it connected to the USB controller via a
Ulpi interface.
Uboot debug indicates that the transfer times out and was still "Active"
The kernel code indicates that a companion driver handles 1.1 devices.
Does this mean there are 2 HCD's, one for HS and one for FS/LS in the
kernel ?
Thank you
ruchika
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: Question about EHCI on P4080
2014-02-20 5:55 Question about EHCI on P4080 Ruchika
@ 2014-02-20 18:56 ` Ruchika
2014-02-21 21:08 ` Scott Wood
0 siblings, 1 reply; 3+ messages in thread
From: Ruchika @ 2014-02-20 18:56 UTC (permalink / raw)
To: linuxppc-dev
linuxppc,
Is there another mailing list which is more appropriate ?
If so I'd be happy to get a recommendation.
Thank you
Regards
ruchika
On 2/19/2014 11:55 PM, Ruchika wrote:
> Hi,
> I've been trying to understand why the uboot code is unable to work with
> USB1.1 devices.
> On a USB analyzer:
> I notice on an analyzer that there are no SOF or IN tokens seen on the
> bus at all. The only after the very first setup packet is sent and ACK'd.
>
> The board has a hub chip on it connected to the USB controller via a
> Ulpi interface.
>
> Uboot debug indicates that the transfer times out and was still "Active"
>
> The kernel code indicates that a companion driver handles 1.1 devices.
> Does this mean there are 2 HCD's, one for HS and one for FS/LS in the
> kernel ?
> Thank you
>
>
> ruchika
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: Question about EHCI on P4080
2014-02-20 18:56 ` Ruchika
@ 2014-02-21 21:08 ` Scott Wood
0 siblings, 0 replies; 3+ messages in thread
From: Scott Wood @ 2014-02-21 21:08 UTC (permalink / raw)
To: Ruchika; +Cc: linuxppc-dev
On Thu, 2014-02-20 at 12:56 -0600, Ruchika wrote:
> linuxppc,
> Is there another mailing list which is more appropriate ?
> If so I'd be happy to get a recommendation.
If you're asking about U-Boot support, the list is u-boot@lists.denx.de
Be sure to mention what version of U-Boot you're using, and that you're
using a recent U-Boot. Also, don't top post or post the same thing
twice.
If you're using U-Boot from the Freescale SDK rather than from upstream,
then instead get support from support@freescale.com or
https://community.freescale.com/ It might be a good idea to go that
route regardless, given that this sounds like it may be a hardware
compatibility issue.
I don't think there is a separate host controller or driver for USB 1.1
(or lower speed USB 2.0) devices on p4080 (though this is common on
PCs).
-Scott
>
> Thank you
> Regards
> ruchika
>
>
> On 2/19/2014 11:55 PM, Ruchika wrote:
> > Hi,
> > I've been trying to understand why the uboot code is unable to work with
> > USB1.1 devices.
> > On a USB analyzer:
> > I notice on an analyzer that there are no SOF or IN tokens seen on the
> > bus at all. The only after the very first setup packet is sent and ACK'd.
> >
> > The board has a hub chip on it connected to the USB controller via a
> > Ulpi interface.
> >
> > Uboot debug indicates that the transfer times out and was still "Active"
> >
> > The kernel code indicates that a companion driver handles 1.1 devices.
> > Does this mean there are 2 HCD's, one for HS and one for FS/LS in the
> > kernel ?
> > Thank you
> >
> >
> > ruchika
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@lists.ozlabs.org
> https://lists.ozlabs.org/listinfo/linuxppc-dev
>
>
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2014-02-21 21:08 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-02-20 5:55 Question about EHCI on P4080 Ruchika
2014-02-20 18:56 ` Ruchika
2014-02-21 21:08 ` Scott Wood
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).