* mpc8560ads PCI bus
@ 2005-03-14 14:56 Greg Weeks
2005-03-14 15:43 ` Clemens Koller
0 siblings, 1 reply; 4+ messages in thread
From: Greg Weeks @ 2005-03-14 14:56 UTC (permalink / raw)
To: linuxppc-embedded
Has anyone else tried to get the PCI bus working on the mpc8560ads board
at 2.6.11? The card enumerates, but the I/O resource regions aren't
getting set up.
-bash-2.05b# lspci -vv
00:03.0 Unknown mass storage controller: Silicon Image, Inc. (formerly
CMD Technology Inc) PCI0680 Ultra ATA-133 Host Controller (rev 02)
Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc)
PCI0680 Ultra ATA-133 Host Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Interrupt: pin A routed to IRQ 100
Region 0: I/O ports at <unassigned> [disabled]
Region 1: I/O ports at <unassigned> [disabled]
Region 2: I/O ports at <unassigned> [disabled]
Region 3: I/O ports at <unassigned> [disabled]
Region 4: I/O ports at <unassigned> [disabled]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Greg Weeks
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: mpc8560ads PCI bus
2005-03-14 14:56 mpc8560ads PCI bus Greg Weeks
@ 2005-03-14 15:43 ` Clemens Koller
2005-03-14 21:24 ` Greg Weeks
0 siblings, 1 reply; 4+ messages in thread
From: Clemens Koller @ 2005-03-14 15:43 UTC (permalink / raw)
To: Greg Weeks, linuxppc-embedded
Hello, Greg,
I am working on an mpc8540_ads-like board and recently, I ran into data
corruption problems with a Silicon Motion SM501 (Rev AA) PCI graphics
card. From my current point of view it seems that Kernel 2.6.11 PCI
works well. I am about to check the hardware and signal integrity.
BTW: I am working with a Promise Ultra-TX133 IDE controller (PDC20269)
which is fine with 66MHz PCICLK.
Greets,
Clemens
> Has anyone else tried to get the PCI bus working on the mpc8560ads board
> at 2.6.11? The card enumerates, but the I/O resource regions aren't
> getting set up.
>
> -bash-2.05b# lspci -vv
> 00:03.0 Unknown mass storage controller: Silicon Image, Inc. (formerly
> CMD Technology Inc) PCI0680 Ultra ATA-133 Host Controller (rev 02)
> Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc)
> PCI0680 Ultra ATA-133 Host Controller
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR+
> Interrupt: pin A routed to IRQ 100
> Region 0: I/O ports at <unassigned> [disabled]
> Region 1: I/O ports at <unassigned> [disabled]
> Region 2: I/O ports at <unassigned> [disabled]
> Region 3: I/O ports at <unassigned> [disabled]
> Region 4: I/O ports at <unassigned> [disabled]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
>
> Greg Weeks
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
>
--
Clemens Koller
_______________________________
R&D Imaging Devices
Anagramm GmbH
Rupert-Mayer-Str. 45/1
81379 Muenchen
Germany
http://www.anagramm.de
Phone: +49-89-741518-50
Fax: +49-89-741518-19
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: mpc8560ads PCI bus
2005-03-14 15:43 ` Clemens Koller
@ 2005-03-14 21:24 ` Greg Weeks
2005-03-15 5:25 ` Kumar Gala
0 siblings, 1 reply; 4+ messages in thread
From: Greg Weeks @ 2005-03-14 21:24 UTC (permalink / raw)
To: linuxppc-embedded
Switch bank SW1 switch #4 was on which stops config accesses from making
it on the bus. It works fine now.
Greg Weeks
Clemens Koller wrote:
> Hello, Greg,
>
> I am working on an mpc8540_ads-like board and recently, I ran into data
> corruption problems with a Silicon Motion SM501 (Rev AA) PCI graphics
> card. From my current point of view it seems that Kernel 2.6.11 PCI
> works well. I am about to check the hardware and signal integrity.
>
> BTW: I am working with a Promise Ultra-TX133 IDE controller (PDC20269)
> which is fine with 66MHz PCICLK.
>
> Greets,
>
> Clemens
>
>
>> Has anyone else tried to get the PCI bus working on the mpc8560ads
>> board at 2.6.11? The card enumerates, but the I/O resource regions
>> aren't getting set up.
>>
>> -bash-2.05b# lspci -vv
>> 00:03.0 Unknown mass storage controller: Silicon Image, Inc.
>> (formerly CMD Technology Inc) PCI0680 Ultra ATA-133 Host Controller
>> (rev 02)
>> Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc)
>> PCI0680 Ultra ATA-133 Host Controller
>> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>> >TAbort- <TAbort- <MAbort- >SERR- <PERR+
>> Interrupt: pin A routed to IRQ 100
>> Region 0: I/O ports at <unassigned> [disabled]
>> Region 1: I/O ports at <unassigned> [disabled]
>> Region 2: I/O ports at <unassigned> [disabled]
>> Region 3: I/O ports at <unassigned> [disabled]
>> Region 4: I/O ports at <unassigned> [disabled]
>> Capabilities: [60] Power Management version 2
>> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
>> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
>>
>> Greg Weeks
>> _______________________________________________
>> Linuxppc-embedded mailing list
>> Linuxppc-embedded@ozlabs.org
>> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
>>
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: mpc8560ads PCI bus
2005-03-14 21:24 ` Greg Weeks
@ 2005-03-15 5:25 ` Kumar Gala
0 siblings, 0 replies; 4+ messages in thread
From: Kumar Gala @ 2005-03-15 5:25 UTC (permalink / raw)
To: Greg Weeks; +Cc: linuxppc-embedded
Greg good to hear, I was about to comment on the fact that PCI based=20
support had been working on the 8540/8560 ADS systems.
- kumar
On Mar 14, 2005, at 3:24 PM, Greg Weeks wrote:
> Switch bank SW1 switch #4 was on which stops config accesses from=20
> making
> it on the bus. It works fine now.
>
> Greg Weeks
>
> Clemens Koller wrote:
>
> > Hello, Greg,
> >
> > I am working on an mpc8540_ads-like board and recently, I ran into=20=
> data
> > corruption problems with a Silicon Motion SM501 (Rev AA) PCI=20
> graphics
> > card. =46rom my current point of view it seems that Kernel 2.6.11 =
PCI
> > works well. I am about to check the hardware and signal integrity.
> >
> > BTW: I am working with a Promise Ultra-TX133 IDE controller=20
> (PDC20269)
> > which is fine with 66MHz PCICLK.
> >
> > Greets,
> >
> > Clemens
> >
> >
> >> Has anyone else tried to get the PCI bus working on the mpc8560ads
> >> board at 2.6.11? The card enumerates, but the I/O resource regions
> >> aren't getting set up.
> >>
> >> -bash-2.05b# lspci -vv
> >> 00:03.0 Unknown mass storage controller: Silicon Image, Inc.
> >> (formerly CMD Technology Inc) PCI0680 Ultra ATA-133 Host Controller
> >> (rev 02)
> >>=A0=A0=A0=A0=A0=A0=A0 Subsystem: Silicon Image, Inc. (formerly CMD =
Technology Inc)
> >> PCI0680 Ultra ATA-133 Host Controller
> >>=A0=A0=A0=A0=A0=A0=A0 Control: I/O- Mem- BusMaster- SpecCycle- =
MemWINV- VGASnoop-
> >> ParErr- Stepping- SERR- FastB2B-
> >>=A0=A0=A0=A0=A0=A0=A0 Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- =
DEVSEL=3Dmedium
> >> >TAbort- <TAbort- <MAbort- >SERR- <PERR+
> >>=A0=A0=A0=A0=A0=A0=A0 Interrupt: pin A routed to IRQ 100
> >>=A0=A0=A0=A0=A0=A0=A0 Region 0: I/O ports at <unassigned> =
[disabled]
> >>=A0=A0=A0=A0=A0=A0=A0 Region 1: I/O ports at <unassigned> =
[disabled]
> >>=A0=A0=A0=A0=A0=A0=A0 Region 2: I/O ports at <unassigned> =
[disabled]
> >>=A0=A0=A0=A0=A0=A0=A0 Region 3: I/O ports at <unassigned> =
[disabled]
> >>=A0=A0=A0=A0=A0=A0=A0 Region 4: I/O ports at <unassigned> =
[disabled]
> >>=A0=A0=A0=A0=A0=A0=A0 Capabilities: [60] Power Management version 2
> >>=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0 Flags: PMEClk- DSI+ =
D1+ D2+ AuxCurrent=3D0mA
> >> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> >>=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0 Status: D0 =
PME-Enable- DSel=3D0 DScale=3D2 PME-
> >>
> >> Greg Weeks
> >> _______________________________________________
> >> Linuxppc-embedded mailing list
> >> Linuxppc-embedded@ozlabs.org
> >> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
> >>
> >
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2005-03-15 5:25 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-03-14 14:56 mpc8560ads PCI bus Greg Weeks
2005-03-14 15:43 ` Clemens Koller
2005-03-14 21:24 ` Greg Weeks
2005-03-15 5:25 ` Kumar Gala
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).