* Re: [PATCH 1/3] add default device trees for MPC837x MDS board
From: Grant Likely @ 2008-01-08 17:53 UTC (permalink / raw)
To: Scott Wood; +Cc: linuxppc-dev, Li Yang, paulus
In-Reply-To: <20080108173845.GA5188@loki.buserror.net>
On 1/8/08, Scott Wood <scottwood@freescale.com> wrote:
> On Tue, Jan 08, 2008 at 08:58:17AM -0700, Grant Likely wrote:
> > On 1/7/08, Li Yang <leoli@freescale.com> wrote:
> > > + phy_type = "utmi_wide";
> >
> > fsl,phy_type please.
>
> Again, code will break. Can we stop ambushing people submitting board
> support with complaints against existing, non-board-specific code/device
> trees? Fix that first, then complain if new code reintroduces the crud.
I disagree (about bringing up these comments). New board port is the
time to bring these issue up. It keeps the issue in the forefront so
it actually gets fixed.
>
> Also, if we're going to change the property name, we should also change the
> underscore to a dash.
Good point, I missed that
g.
--
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
^ permalink raw reply
* Re: [PATCH 3/7] Basic Freescale MPC512x support
From: Scott Wood @ 2008-01-08 17:55 UTC (permalink / raw)
To: Grant Likely; +Cc: linuxppc-dev, John Rigby
In-Reply-To: <fa686aa40801080919y7c426007vd031bb79e8f9a03d@mail.gmail.com>
On Tue, Jan 08, 2008 at 10:19:20AM -0700, Grant Likely wrote:
> > +config MPC5121_ADS
> > + bool "Freescale MPC5121E ADS"
> > + select DEFAULT_UIMAGE
> > + help
> > + This option enables support for the MPC5121E ADS board.
>
> Make this depend on PPC_MULTIPLATFORM and PPC32
I don't think PPC_MULTIPLATFORM is appropriate here... it seems to be
OF-specific.
-Scott
^ permalink raw reply
* Re: [PATCH 3/7] Basic Freescale MPC512x support
From: Grant Likely @ 2008-01-08 17:56 UTC (permalink / raw)
To: Scott Wood; +Cc: linuxppc-dev, John Rigby
In-Reply-To: <20080108175513.GC5188@loki.buserror.net>
On 1/8/08, Scott Wood <scottwood@freescale.com> wrote:
> On Tue, Jan 08, 2008 at 10:19:20AM -0700, Grant Likely wrote:
> > > +config MPC5121_ADS
> > > + bool "Freescale MPC5121E ADS"
> > > + select DEFAULT_UIMAGE
> > > + help
> > > + This option enables support for the MPC5121E ADS board.
> >
> > Make this depend on PPC_MULTIPLATFORM and PPC32
>
> I don't think PPC_MULTIPLATFORM is appropriate here... it seems to be
> OF-specific.
52xx is multiplatform. It works well on both OF and non-OF boards.
Cheers,
g.
--
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
^ permalink raw reply
* Re: [PATCH 3/7] Basic Freescale MPC512x support
From: John Rigby @ 2008-01-08 18:01 UTC (permalink / raw)
To: Olof Johansson; +Cc: linuxppc-dev
In-Reply-To: <20080108174038.GA20819@lixom.net>
Olof Johansson wrote:
> Hi,
>
>
>
>> diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
>> index 66a3d8c..81c3f05 100644
>> --- a/arch/powerpc/Kconfig
>> +++ b/arch/powerpc/Kconfig
>> @@ -470,7 +470,7 @@ config PCI
>> bool "PCI support" if 40x || CPM2 || PPC_83xx || PPC_85xx || PPC_86xx \
>> || PPC_MPC52xx || (EMBEDDED && (PPC_PSERIES || PPC_ISERIES)) \
>> || PPC_PS3
>> - default y if !40x && !CPM2 && !8xx && !PPC_83xx \
>> + default y if !40x && !CPM2 && !8xx && !PPC_512x && !PPC_83xx \
>> && !PPC_85xx && !PPC_86xx
>>
>
> This is getting out of control. Not a comment to this specific patch,
> but it's getting silly.
>
> Btw, why no PCI by default on this platform when it seemingly is default
> on 5200? I thought they were fairly similar.
>
PCI has issues in first silicon so I left that out.
Also contrary to popular rumor, 5121 is more like a 83xx that 52xx.
The PCI and USB are very similar to 83xx.
>
>> diff --git a/arch/powerpc/platforms/512x/Kconfig b/arch/powerpc/platforms/512x/Kconfig
>> new file mode 100644
>> index 0000000..399d279
>> --- /dev/null
>> +++ b/arch/powerpc/platforms/512x/Kconfig
>> @@ -0,0 +1,20 @@
>> +menu "Platform support"
>> + depends on PPC_512x
>> +
>> +choice
>> + prompt "Machine Type"
>> + default MPC5121_ADS
>> +
>> +config MPC5121_ADS
>> + bool "Freescale MPC5121E ADS"
>> + select DEFAULT_UIMAGE
>> + help
>> + This option enables support for the MPC5121E ADS board.
>> +
>> +endchoice
>>
>
> For new platforms it makes more sense to make it possible to build
> multiplatform kernels instead of using 'choice'.
>
> I know some embedded board guys prefer to build a custom kernel for just
> their board (since it means extra revenue for them to spin a kernel
> for every customer), but it's still convenient to be able to build
> multiplatform kernels. Especially since there's some companies out there
> with intent to make end-user products with this cpu.
>
Grant made the same comment about multiplatform support.
I'll change this.
>
>> @@ -0,0 +1,90 @@
>> +#include <asm/system.h>
>> +#include <asm/atomic.h>
>> +#include <asm/machdep.h>
>> +#include <asm/ipic.h>
>> +#include <asm/prom.h>
>> +#include <asm/time.h>
>> +#include <asm/of_platform.h>
>>
>
> Stephen will tell you to include linux/of_platform.h instead. :-)
>
Oops, this patch was originally done before the open firmware
unification. I guess checkpatch.pl needs an update too.
>
>> @@ -229,7 +229,7 @@ config NR_CPUS
>>
>> config NOT_COHERENT_CACHE
>> bool
>> - depends on 4xx || 8xx || E200
>> + depends on 4xx || 8xx || E200 || PPC_512x
>> default y
>>
>
> Why do you need this, when 5200 doesn't?
>
>
> -Olof
>
>
^ permalink raw reply
* Re: [PATCH 3/7] Basic Freescale MPC512x support
From: Arnd Bergmann @ 2008-01-08 18:07 UTC (permalink / raw)
To: linuxppc-dev; +Cc: John Rigby
In-Reply-To: <1199808093-15929-4-git-send-email-jrigby@freescale.com>
On Tuesday 08 January 2008, John Rigby wrote:
> =A0obj-$(CONFIG_PPC_CHRP)=A0=A0=A0=A0=A0=A0=A0=A0=A0+=3D chrp/
> =A0obj-$(CONFIG_40x)=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0+=3D 40x/
> =A0obj-$(CONFIG_44x)=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0+=3D 44x/
> +obj-$(CONFIG_PPC_512x)=A0=A0=A0=A0=A0=A0=A0=A0=A0+=3D 512x/
> =A0obj-$(CONFIG_PPC_MPC52xx)=A0=A0=A0=A0=A0=A0+=3D 52xx/
> =A0obj-$(CONFIG_PPC_8xx)=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0+=3D 8xx/
> =A0obj-$(CONFIG_PPC_82xx)=A0=A0=A0=A0=A0=A0=A0=A0=A0+=3D 82xx/
Why do you name the directory 512x instead of 51xx, which would be
more consistent with the others? Do you expect other 51xx chips that
are mostly incompatible with 512x?
Moreover, is it really so different from 52xx that it needs a separate
directory? E.g. we often treat the 74xx and 7xx as 6xx variants.
Arnd <><
^ permalink raw reply
* Re: [PATCH] Hwmon for Taco
From: Sean MacLennan @ 2008-01-08 18:09 UTC (permalink / raw)
To: Grant Likely; +Cc: linuxppc-dev
In-Reply-To: <fa686aa40801072259w63899e74y45d55bd5e9844b68@mail.gmail.com>
Grant Likely wrote:
> This is *very* board specific and not very complex a driver. It
> should probably live with the platform code somewhere in
> arch/powerpc/platforms. You can use the machine_device_initcall()
> hook to kick off the thread.
>
Doh, this is why I post to this list. The platform code already had an
obvious place to put this, so I moved it there.
I will cleanup the ad7414.c driver and repost the patch.
Cheers,
Sean
^ permalink raw reply
* Re: [PATCH 3/7] Basic Freescale MPC512x support
From: Arnd Bergmann @ 2008-01-08 18:13 UTC (permalink / raw)
To: linuxppc-dev; +Cc: Olof Johansson, John Rigby
In-Reply-To: <20080108174038.GA20819@lixom.net>
On Tuesday 08 January 2008, Olof Johansson wrote:
> > diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
> > index 66a3d8c..81c3f05 100644
> > --- a/arch/powerpc/Kconfig
> > +++ b/arch/powerpc/Kconfig
> > @@ -470,7 +470,7 @@ config PCI
> > =A0=A0=A0=A0=A0=A0bool "PCI support" if 40x || CPM2 || PPC_83xx || PPC_=
85xx || PPC_86xx \
> > =A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0|| PPC_MPC52xx || (EMBEDDED &=
& (PPC_PSERIES || PPC_ISERIES)) \
> > =A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0|| PPC_PS3
> > -=A0=A0=A0=A0=A0default y if !40x && !CPM2 && !8xx && !PPC_83xx \
> > +=A0=A0=A0=A0=A0default y if !40x && !CPM2 && !8xx && !PPC_512x && !PPC=
_83xx \
> > =A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0&& !PPC_85xx && !PPC_86xx
>=20
> This is getting out of control. Not a comment to this specific patch,
> but it's getting silly.
>=20
> Btw, why no PCI by default on this platform when it seemingly is default
> on 5200? I thought they were fairly similar.
>=20
Just an idea how to restructure this, you could have
config PCI_POSSIBLE
bool
help
select this from your platform if it can support PCI.
config PCI_DEFAULT
bool
select
help
select this from your platform if you want PCI on by default
config PCI
bool "PCI support"
depends on PCI_POSSIBLE || PCI_DEFAULT
default PCI_DEFAULT
config 40x
# there could be PCI, but normally there isn't
select PCI_POSSIBLE
=09
config PPC_83xx=20
# PCI is normally wanted on 83xx, but you can disable it
select PCI_DEFAULT
config CHRP
# CHRP can only be built correctly when PCI is enabled
select PCI
Arnd <><
^ permalink raw reply
* Re: [PATCH 6/7] Add mpc512x_find_ips_freq
From: Arnd Bergmann @ 2008-01-08 18:15 UTC (permalink / raw)
To: linuxppc-dev; +Cc: John Rigby
In-Reply-To: <1199808093-15929-7-git-send-email-jrigby@freescale.com>
On Tuesday 08 January 2008, John Rigby wrote:
> +unsigned long
> +mpc512x_find_ips_freq(struct device_node *node)
> +{
The driver that is using this is listed as 'tristate' in Kconfig, but
this function is not exported, so you get a link error if you want to
build it as a module.
Arnd <><
^ permalink raw reply
* Re: [PATCH 3/7] Basic Freescale MPC512x support
From: John Rigby @ 2008-01-08 18:16 UTC (permalink / raw)
To: Olof Johansson; +Cc: linuxppc-dev
In-Reply-To: <20080108174038.GA20819@lixom.net>
>
>
>> @@ -229,7 +229,7 @@ config NR_CPUS
>>
>> config NOT_COHERENT_CACHE
>> bool
>> - depends on 4xx || 8xx || E200
>> + depends on 4xx || 8xx || E200 || PPC_512x
>> default y
>>
>
> Why do you need this, when 5200 doesn't?
>
>
Because the 5121 cache is not coherent. The 5121 is not that similar
to 52xx.
> -Olof
>
>
^ permalink raw reply
* Re: [PATCH 3/7] Basic Freescale MPC512x support
From: John Rigby @ 2008-01-08 18:25 UTC (permalink / raw)
To: Arnd Bergmann; +Cc: linuxppc-dev
In-Reply-To: <200801081907.59052.arnd@arndb.de>
Arnd Bergmann wrote:
> On Tuesday 08 January 2008, John Rigby wrote:
>
>> obj-$(CONFIG_PPC_CHRP) += chrp/
>> obj-$(CONFIG_40x) += 40x/
>> obj-$(CONFIG_44x) += 44x/
>> +obj-$(CONFIG_PPC_512x) += 512x/
>> obj-$(CONFIG_PPC_MPC52xx) += 52xx/
>> obj-$(CONFIG_PPC_8xx) += 8xx/
>> obj-$(CONFIG_PPC_82xx) += 82xx/
>>
>
> Why do you name the directory 512x instead of 51xx, which would be
> more consistent with the others? Do you expect other 51xx chips that
> are mostly incompatible with 512x?
>
51xx would be confusing because 5100 was a precursor to the 5200.
Adding it to 52xx would is wrong because 5121 is really not that
much like a 5200. It is really a 83xx minus some networking hw
plus some 5200 peripherals (PSCs and MSCAN).
In the best of possible worlds it would have a 83xx part number
and go in 83xx but that would be confusing since it is targeted
at the automotive market.
> Moreover, is it really so different from 52xx that it needs a separate
> directory? E.g. we often treat the 74xx and 7xx as 6xx variants.
>
> Arnd <><
>
>
^ permalink raw reply
* Re: [PATCH] Hwmon for Taco
From: Sean MacLennan @ 2008-01-08 18:30 UTC (permalink / raw)
To: Grant Likely; +Cc: linuxppc-dev
In-Reply-To: <fa686aa40801072259w63899e74y45d55bd5e9844b68@mail.gmail.com>
Ok, here is the ad7414 only. taco-dtm is no more!
Cheers,
Sean
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index a0445be..f14972a 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -57,6 +57,16 @@ config SENSORS_ABITUGURU3
This driver can also be built as a module. If so, the module
will be called abituguru3.
+config SENSORS_AD7414
+ tristate "Analog Devices AD7414"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for the Analog Devices
+ AD7414 temperature monitoring chip.
+
+ This driver can also be built as a module. If so, the module
+ will be called ad7414.
+
config SENSORS_AD7418
tristate "Analog Devices AD7416, AD7417 and AD7418"
depends on I2C && EXPERIMENTAL
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index 55595f6..fa6066e 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_SENSORS_W83791D) += w83791d.o
obj-$(CONFIG_SENSORS_ABITUGURU) += abituguru.o
obj-$(CONFIG_SENSORS_ABITUGURU3)+= abituguru3.o
+obj-$(CONFIG_SENSORS_AD7414) += ad7414.o
obj-$(CONFIG_SENSORS_AD7418) += ad7418.o
obj-$(CONFIG_SENSORS_ADM1021) += adm1021.o
obj-$(CONFIG_SENSORS_ADM1025) += adm1025.o
@@ -72,4 +73,3 @@ obj-$(CONFIG_SENSORS_W83L785TS) += w83l785ts.o
ifeq ($(CONFIG_HWMON_DEBUG_CHIP),y)
EXTRA_CFLAGS += -DDEBUG
endif
-
--- /dev/null 2005-11-20 22:22:37.000000000 -0500
+++ drivers/hwmon/ad7414.c 2008-01-08 02:43:24.000000000 -0500
@@ -0,0 +1,319 @@
+/*
+ * An hwmon driver for the Analog Devices AD7414
+ *
+ * Copyright 2006 Stefan Roese <sr@denx.de>, DENX Software Engineering
+ *
+ * Based on ad7418.c
+ * Copyright 2006 Tower Technologies, Alessandro Zummo <a.zummo@towertech.it>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/delay.h>
+
+
+#define DRV_VERSION "0.2"
+
+/* straight from the datasheet */
+#define AD7414_TEMP_MIN (-55000)
+#define AD7414_TEMP_MAX 125000
+
+/* Addresses to scan */
+static unsigned short normal_i2c[] = { 0x48, 0x4a, I2C_CLIENT_END };
+
+/* Insmod parameters */
+I2C_CLIENT_INSMOD;
+
+/* AD7414 registers */
+#define AD7414_REG_TEMP 0x00
+#define AD7414_REG_CONF 0x01
+#define AD7414_REG_T_HIGH 0x02
+#define AD7414_REG_T_LOW 0x03
+
+struct ad7414_data {
+ struct i2c_client client;
+ struct device *dev;
+ struct mutex lock;
+ char valid; /* !=0 if following fields are valid */
+ unsigned long last_updated; /* In jiffies */
+ u16 temp_input; /* Register values */
+ u8 temp_max;
+ u8 temp_min;
+ u8 temp_alert;
+ u8 temp_max_flag;
+ u8 temp_min_flag;
+};
+
+
+struct ad7414_dev {
+ struct list_head list;
+ struct device *dev;
+};
+
+static LIST_HEAD(ad7414_dev_list);
+
+
+static int ad7414_attach_adapter(struct i2c_adapter *adapter);
+static int ad7414_detect(struct i2c_adapter *adapter, int address, int kind);
+static int ad7414_detach_client(struct i2c_client *client);
+
+static struct i2c_driver ad7414_driver = {
+ .driver = {
+ .name = "ad7414",
+ },
+ .attach_adapter = ad7414_attach_adapter,
+ .detach_client = ad7414_detach_client,
+};
+
+/*
+ * TEMP: 0.001C/bit (-55C to +125C)
+ * REG: (0.5C/bit, two's complement) << 7
+ */
+static inline int AD7414_TEMP_FROM_REG(u16 reg)
+{
+ /* use integer division instead of equivalent right shift to
+ * guarantee arithmetic shift and preserve the sign
+ */
+ return ((s16)reg / 128) * 500;
+}
+
+/* All registers are word-sized, except for the configuration registers.
+ * AD7414 uses a high-byte first convention, which is exactly opposite to
+ * the usual practice.
+ */
+static int ad7414_read(struct i2c_client *client, u8 reg)
+{
+ if (reg == AD7414_REG_TEMP)
+ return swab16(i2c_smbus_read_word_data(client, reg));
+ else
+ return i2c_smbus_read_byte_data(client, reg);
+}
+
+static int ad7414_write(struct i2c_client *client, u8 reg, u16 value)
+{
+ return i2c_smbus_write_byte_data(client, reg, value);
+}
+
+static void ad7414_init_client(struct i2c_client *client)
+{
+ struct ad7414_dev *new;
+
+ new = kzalloc(sizeof(*new), GFP_KERNEL);
+ if(new == NULL)
+ printk(KERN_ERR "ad7414_init_client: Unable to allocate memory\n");
+ else {
+ new->dev = &client->dev;
+ list_add_tail(&new->list, &ad7414_dev_list);
+ }
+}
+
+static struct ad7414_data *ad7414_update_device(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct ad7414_data *data = i2c_get_clientdata(client);
+
+ mutex_lock(&data->lock);
+
+ if (time_after(jiffies, data->last_updated + HZ + HZ / 2)
+ || !data->valid) {
+ dev_dbg(&client->dev, "starting ad7414 update\n");
+
+ data->temp_input = ad7414_read(client, AD7414_REG_TEMP);
+ data->temp_alert = (data->temp_input >> 5) & 0x01;
+ data->temp_max_flag = (data->temp_input >> 4) & 0x01;
+ data->temp_min_flag = (data->temp_input >> 3) & 0x01;
+ data->temp_max = ad7414_read(client, AD7414_REG_T_HIGH);
+ data->temp_min = ad7414_read(client, AD7414_REG_T_LOW);
+
+ data->last_updated = jiffies;
+ data->valid = 1;
+ }
+
+ mutex_unlock(&data->lock);
+
+ return data;
+}
+
+int ad7414_get_temp(int index)
+{
+ struct ad7414_dev *dev;
+
+ list_for_each_entry(dev, &ad7414_dev_list, list) {
+ if(index <= 0) {
+ struct ad7414_data *data = ad7414_update_device(dev->dev);
+ return data->temp_input;
+ }
+ --index;
+ }
+
+ return 0x1f4; /* +125 */
+}
+EXPORT_SYMBOL(ad7414_get_temp);
+
+#define show(value) \
+static ssize_t show_##value(struct device *dev, struct device_attribute *attr, char *buf) \
+{ \
+ struct ad7414_data *data = ad7414_update_device(dev); \
+ return sprintf(buf, "%d\n", AD7414_TEMP_FROM_REG(data->value)); \
+}
+show(temp_input);
+
+#define show_8(value) \
+static ssize_t show_##value(struct device *dev, struct device_attribute *attr, char *buf) \
+{ \
+ struct ad7414_data *data = ad7414_update_device(dev); \
+ return sprintf(buf, "%d\n", data->value); \
+}
+show_8(temp_max);
+show_8(temp_min);
+show_8(temp_alert);
+show_8(temp_max_flag);
+show_8(temp_min_flag);
+
+#define set(value, reg) \
+static ssize_t set_##value(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) \
+{ \
+ struct i2c_client *client = to_i2c_client(dev); \
+ struct ad7414_data *data = i2c_get_clientdata(client); \
+ int temp = simple_strtoul(buf, NULL, 10); \
+ \
+ mutex_lock(&data->lock); \
+ data->value = temp; \
+ ad7414_write(client, reg, data->value); \
+ mutex_unlock(&data->lock); \
+ return count; \
+}
+set(temp_max, AD7414_REG_T_HIGH);
+set(temp_min, AD7414_REG_T_LOW);
+
+static DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO, show_temp_max, set_temp_max);
+static DEVICE_ATTR(temp1_min, S_IWUSR | S_IRUGO, show_temp_min, set_temp_min);
+static DEVICE_ATTR(temp1_input, S_IRUGO, show_temp_input, NULL);
+static DEVICE_ATTR(temp1_alert, S_IRUGO, show_temp_alert, NULL);
+static DEVICE_ATTR(temp1_max_flag, S_IRUGO, show_temp_max_flag, NULL);
+static DEVICE_ATTR(temp1_min_flag, S_IRUGO, show_temp_min_flag, NULL);
+
+static int ad7414_attach_adapter(struct i2c_adapter *adapter)
+{
+ if (!(adapter->class & I2C_CLASS_HWMON))
+ return 0;
+ return i2c_probe(adapter, &addr_data, ad7414_detect);
+}
+
+static struct attribute *ad7414_attributes[] = {
+ &dev_attr_temp1_input.attr,
+ &dev_attr_temp1_max.attr,
+ &dev_attr_temp1_min.attr,
+ &dev_attr_temp1_alert.attr,
+ &dev_attr_temp1_max_flag.attr,
+ &dev_attr_temp1_min_flag.attr,
+ NULL
+};
+
+static const struct attribute_group ad7414_group = {
+ .attrs = ad7414_attributes,
+};
+
+static int ad7414_detect(struct i2c_adapter *adapter, int address, int kind)
+{
+ struct i2c_client *client;
+ struct ad7414_data *data;
+ int err = 0;
+
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA |
+ I2C_FUNC_SMBUS_WORD_DATA))
+ goto exit;
+
+ if (!(data = kzalloc(sizeof(struct ad7414_data), GFP_KERNEL))) {
+ err = -ENOMEM;
+ goto exit;
+ }
+
+ client = &data->client;
+ client->addr = address;
+ client->adapter = adapter;
+ client->driver = &ad7414_driver;
+ client->flags = 0;
+
+ i2c_set_clientdata(client, data);
+
+ mutex_init(&data->lock);
+
+ /* TODO: not testing for AD7414 done yet... */
+
+ strlcpy(client->name, ad7414_driver.driver.name, I2C_NAME_SIZE);
+
+ if ((err = i2c_attach_client(client)))
+ goto exit_free;
+
+ dev_info(&client->dev, "chip found, driver version " DRV_VERSION "\n");
+
+ /* Initialize the AD7414 chip */
+ ad7414_init_client(client);
+
+ /* Register sysfs hooks */
+ if ((err = sysfs_create_group(&client->dev.kobj, &ad7414_group)))
+ goto exit_detach;
+
+ data->dev = hwmon_device_register(&client->dev);
+ if (IS_ERR(data->dev)) {
+ err = PTR_ERR(data->dev);
+ goto exit_remove;
+ }
+
+ return 0;
+
+exit_remove:
+ sysfs_remove_group(&client->dev.kobj, &ad7414_group);
+exit_detach:
+ i2c_detach_client(client);
+exit_free:
+ kfree(data);
+exit:
+ return err;
+}
+
+static int ad7414_detach_client(struct i2c_client *client)
+{
+ struct ad7414_data *data = i2c_get_clientdata(client);
+ struct ad7414_dev *dev;
+
+ list_for_each_entry(dev, &ad7414_dev_list, list)
+ if(dev->dev == &client->dev) {
+ list_del(&dev->list);
+ break;
+ }
+
+ hwmon_device_unregister(data->dev);
+ sysfs_remove_group(&client->dev.kobj, &ad7414_group);
+ i2c_detach_client(client);
+ kfree(data);
+ return 0;
+}
+
+static int __init ad7414_init(void)
+{
+ return i2c_add_driver(&ad7414_driver);
+}
+
+static void __exit ad7414_exit(void)
+{
+ i2c_del_driver(&ad7414_driver);
+}
+
+MODULE_AUTHOR("Stefan Roese <sr@denx.de>");
+MODULE_DESCRIPTION("AD7414 driver");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
+
+module_init(ad7414_init);
+module_exit(ad7414_exit);
^ permalink raw reply related
* Re: [PATCH 4/8] pseries: phyp dump: use sysfs to release reserved mem
From: Linas Vepstas @ 2008-01-08 18:34 UTC (permalink / raw)
To: Stephen Rothwell; +Cc: mahuja, linuxppc-dev, lkessler, strosake
In-Reply-To: <20080108144537.39f21cd4.sfr@canb.auug.org.au>
On 07/01/2008, Stephen Rothwell <sfr@canb.auug.org.au> wrote:
> On Mon, 07 Jan 2008 18:21:57 -0600 Manish Ahuja <ahuja@austin.ibm.com> wrote:
> >
> > +static int __init phyp_dump_setup(void)
> > +{
> >
> > + /* Is there dump data waiting for us? */
> > + rtas = of_find_node_by_path("/rtas");
> > + dump_header = of_get_property(rtas, "ibm,kernel-dump", &header_len);
> ^^^^^^^^^^^
> You could pass NULL here as header_len appears to be unused. Also you
> need "of_node_put(rtas)" somewhere (probably just here would do).
Perhaps the routine should have been "of_get_node_by_path()" ?
In ye olden days, "finds" didn't require put, but "gets" did. I'm guessing
that this has now all been fixed up for the of_xxx routines, but I think
that pci_find_xxx still does not require a pci_put.
Why did I bother to write this email? I dunno...
--linas
^ permalink raw reply
* [PATCH RFC 0/3] PowerPC: implement support for GPIO LIB API
From: Anton Vorontsov @ 2008-01-08 18:43 UTC (permalink / raw)
To: linuxppc-dev; +Cc: Arnd Bergmann, David Gibson
Hi all,
Thanks for the previous review and ideas. Here is the RFC for the
GPIO LIB support.
I'm using it like this:
qe_pio_a: gpio-controller@1400 {
#gpio-cells = <1>;
compatible = "fsl,qe-pario-bank";
reg = <0x1400 0x18>;
gpio-controller;
};
qe_pio_e: gpio-controller@1460 {
#gpio-cells = <1>;
compatible = "fsl,qe-pario-bank";
reg = <0x1460 0x18>;
gpio-controller;
};
nand-flash@1,0 {
compatible = "stmicro,NAND512W3A2BN6E", "fsl,upm-nand";
reg = <1 0 1>;
width = <1>;
upm = "A";
upm-addr-offset = <16>;
upm-cmd-offset = <8>;
gpios = <&qe_pio_e 18 &qe_pio_a 9>;
wait-pattern;
wait-write;
};
As you can see I've split single "par_io" node into banks, thus
the benefits:
- we can handle banks of different width (Jochen Friedrich asked for
this, IIRC. Or I've misunderstood ;-).
- we can handle banks with different paddings (no more #ifdef PPC85xx).
Also, it's possible to specify different gpio-controllers in the
gpios = <> property. gpio-specifier is controller specific.
The remaining question is about gpio.c placement. prom_parse.c doesn't
feel as the appropriate place anymore. I think of:
- drivers/gpio/of_gpio.c (driver/gpio/ is in -mm tree);
- drivers/of/gpio.c
- keep it in arch/powerpc/kernel/ (though, there is nothing
much PowerPC specific).
So, to try these patches you'll need apply these from the -mm tree:
generic-gpio-gpio_chip-support.patch
generic-gpio-gpio_chip-support-fix.patch
generic-gpio-gpio_chip-support-gpiolib-locking-simplified.patch
Or just issue this in your working tree:
git pull git://git.infradead.org/users/cbou/powerpc-gpio.git gpiolib
powerpc-gpio.git's gpiolib branch is galak/powerpc.git master branch +
-mm patches + these patches.
Support for CPM2 is pending.
Thanks!
--
Anton Vorontsov
email: cbou@mail.ru
backup email: ya-cbou@yandex.ru
irc://irc.freenode.net/bd2
^ permalink raw reply
* Re: [PATCH] i2c-ibm_iic driver - new patch
From: Sean MacLennan @ 2008-01-08 18:35 UTC (permalink / raw)
To: Stephen Rothwell; +Cc: linuxppc-dev, Stefan Roese, Arnd Bergmann
In-Reply-To: <20080108173636.73db1623.sfr@canb.auug.org.au>
Let's try again.
Cheers,
Sean
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index c466c6c..e9e1493 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -241,7 +241,6 @@ config I2C_PIIX4
config I2C_IBM_IIC
tristate "IBM PPC 4xx on-chip I2C interface"
- depends on IBM_OCP
help
Say Y here if you want to use IIC peripheral found on
embedded IBM PPC 4xx based systems.
diff --git a/drivers/i2c/busses/i2c-ibm_iic.c b/drivers/i2c/busses/i2c-ibm_iic.c
index 9b43ff7..98476fc 100644
--- a/drivers/i2c/busses/i2c-ibm_iic.c
+++ b/drivers/i2c/busses/i2c-ibm_iic.c
@@ -6,6 +6,9 @@
* Copyright (c) 2003, 2004 Zultys Technologies.
* Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
*
+ * Copyright (c) 2008 PIKA Technologies
+ * Sean MacLennan <smaclennan@pikatech.com>
+ *
* Based on original work by
* Ian DaSilva <idasilva@mvista.com>
* Armin Kuster <akuster@mvista.com>
@@ -39,12 +42,17 @@
#include <asm/io.h>
#include <linux/i2c.h>
#include <linux/i2c-id.h>
+
+#ifdef CONFIG_IBM_OCP
#include <asm/ocp.h>
#include <asm/ibm4xx.h>
+#else
+#include <linux/of_platform.h>
+#endif
#include "i2c-ibm_iic.h"
-#define DRIVER_VERSION "2.1"
+#define DRIVER_VERSION "2.2"
MODULE_DESCRIPTION("IBM IIC driver v" DRIVER_VERSION);
MODULE_LICENSE("GPL");
@@ -650,13 +658,14 @@ static inline u8 iic_clckdiv(unsigned int opb)
opb /= 1000000;
if (opb < 20 || opb > 150){
- printk(KERN_CRIT "ibm-iic: invalid OPB clock frequency %u MHz\n",
+ printk(KERN_WARNING "ibm-iic: invalid OPB clock frequency %u MHz\n",
opb);
opb = opb < 20 ? 20 : 150;
}
return (u8)((opb + 9) / 10 - 1);
}
+#ifdef CONFIG_IBM_OCP
/*
* Register single IIC interface
*/
@@ -672,7 +681,7 @@ static int __devinit iic_probe(struct ocp_device *ocp){
ocp->def->index);
if (!(dev = kzalloc(sizeof(*dev), GFP_KERNEL))) {
- printk(KERN_CRIT "ibm-iic%d: failed to allocate device data\n",
+ printk(KERN_ERR "ibm-iic%d: failed to allocate device data\n",
ocp->def->index);
return -ENOMEM;
}
@@ -687,7 +696,7 @@ static int __devinit iic_probe(struct ocp_device *ocp){
}
if (!(dev->vaddr = ioremap(ocp->def->paddr, sizeof(struct iic_regs)))){
- printk(KERN_CRIT "ibm-iic%d: failed to ioremap device registers\n",
+ printk(KERN_ERR "ibm-iic%d: failed to ioremap device registers\n",
dev->idx);
ret = -ENXIO;
goto fail2;
@@ -746,7 +755,7 @@ static int __devinit iic_probe(struct ocp_device *ocp){
adap->nr = dev->idx >= 0 ? dev->idx : 0;
if ((ret = i2c_add_numbered_adapter(adap)) < 0) {
- printk(KERN_CRIT "ibm-iic%d: failed to register i2c adapter\n",
+ printk(KERN_ERR "ibm-iic%d: failed to register i2c adapter\n",
dev->idx);
goto fail;
}
@@ -779,7 +788,7 @@ static void __devexit iic_remove(struct ocp_device *ocp)
struct ibm_iic_private* dev = (struct ibm_iic_private*)ocp_get_drvdata(ocp);
BUG_ON(dev == NULL);
if (i2c_del_adapter(&dev->adap)){
- printk(KERN_CRIT "ibm-iic%d: failed to delete i2c adapter :(\n",
+ printk(KERN_ERR "ibm-iic%d: failed to delete i2c adapter :(\n",
dev->idx);
/* That's *very* bad, just shutdown IRQ ... */
if (dev->irq >= 0){
@@ -831,3 +840,189 @@ static void __exit iic_exit(void)
module_init(iic_init);
module_exit(iic_exit);
+#else
+/*
+ * Register single IIC interface
+ */
+static int __devinit iic_probe(struct of_device *ofdev,
+ const struct of_device_id *match)
+{
+ static int index = 0;
+ struct device_node *np = ofdev->node;
+ struct ibm_iic_private* dev;
+ struct i2c_adapter* adap;
+ const u32 *indexp, *freq;
+ int ret;
+
+ dev = kzalloc(sizeof(*dev), GFP_KERNEL);
+ if (!dev) {
+ printk(KERN_ERR "ibm-iic: failed to allocate device data\n");
+ return -ENOMEM;
+ }
+
+ /* This assumes we don't mix index and non-index entries. */
+ indexp = of_get_property(np, "index", NULL);
+ dev->idx = indexp ? *indexp : index++;
+
+ dev_set_drvdata(&ofdev->dev, dev);
+
+ dev->vaddr = of_iomap(np, 0);
+ if (dev->vaddr == NULL) {
+ printk(KERN_ERR "ibm-iic%d: failed to ioremap device registers\n",
+ dev->idx);
+ ret = -ENXIO;
+ goto fail1;
+ }
+
+ init_waitqueue_head(&dev->wq);
+
+ if (iic_force_poll)
+ dev->irq = NO_IRQ;
+ else {
+ dev->irq = irq_of_parse_and_map(np, 0);
+ if (dev->irq == NO_IRQ)
+ printk(KERN_ERR __FILE__ ": irq_of_parse_and_map failed\n");
+ else {
+ /* Disable interrupts until we finish initialization,
+ assumes level-sensitive IRQ setup...
+ */
+ iic_interrupt_mode(dev, 0);
+ if (request_irq(dev->irq, iic_handler, 0, "IBM IIC", dev)){
+ printk(KERN_ERR "ibm-iic%d: request_irq %d failed\n",
+ dev->idx, dev->irq);
+ /* Fallback to the polling mode */
+ dev->irq = NO_IRQ;
+ }
+ }
+ }
+
+ if (dev->irq == NO_IRQ)
+ printk(KERN_WARNING "ibm-iic%d: using polling mode\n",
+ dev->idx);
+
+ /* Board specific settings */
+ if (iic_force_fast || of_get_property(np, "fast-mode", NULL))
+ dev->fast_mode = 1;
+ else
+ dev->fast_mode = 0;
+
+ /* clckdiv is the same for *all* IIC interfaces, but I'd rather
+ * make a copy than introduce another global. --ebs
+ */
+ freq = of_get_property(np, "clock-frequency", NULL);
+ if (freq == NULL) {
+ freq = of_get_property(np->parent, "clock-frequency", NULL);
+ if (freq == NULL) {
+ printk(KERN_ERR "ibm-iic%d: Unable to get bus frequency\n",
+ dev->idx);
+ ret = -EBUSY;
+ goto fail;
+ }
+ }
+
+ dev->clckdiv = iic_clckdiv(*freq);
+ DBG("%d: clckdiv = %d\n", dev->idx, dev->clckdiv);
+
+ /* Initialize IIC interface */
+ iic_dev_init(dev);
+
+ /* Register it with i2c layer */
+ adap = &dev->adap;
+ adap->dev.parent = &ofdev->dev;
+ strcpy(adap->name, "IBM IIC");
+ i2c_set_adapdata(adap, dev);
+ adap->id = I2C_HW_OCP;
+ adap->class = I2C_CLASS_HWMON;
+ adap->algo = &iic_algo;
+ adap->client_register = NULL;
+ adap->client_unregister = NULL;
+ adap->timeout = 1;
+ adap->retries = 1;
+ adap->nr = dev->idx;
+
+ ret = i2c_add_numbered_adapter(adap);
+ if (ret < 0) {
+ printk(KERN_ERR "ibm-iic%d: failed to register i2c adapter\n",
+ dev->idx);
+ goto fail;
+ }
+
+ printk(KERN_INFO "ibm-iic%d: using %s mode\n", dev->idx,
+ dev->fast_mode ? "fast (400 kHz)" : "standard (100 kHz)");
+
+ return 0;
+
+fail:
+ if (dev->irq != NO_IRQ){
+ iic_interrupt_mode(dev, 0);
+ free_irq(dev->irq, dev);
+ }
+
+ iounmap(dev->vaddr);
+fail1:
+ dev_set_drvdata(&ofdev->dev, NULL);
+ kfree(dev);
+ return ret;
+}
+
+/*
+ * Cleanup initialized IIC interface
+ */
+static int __devexit iic_remove(struct of_device *ofdev)
+{
+ struct ibm_iic_private* dev = dev_get_drvdata(&ofdev->dev);
+
+ BUG_ON(dev == NULL);
+ if (i2c_del_adapter(&dev->adap)){
+ printk(KERN_ERR "ibm-iic%d: failed to delete i2c adapter :(\n",
+ dev->idx);
+ /* That's *very* bad, just shutdown IRQ ... */
+ if (dev->irq != NO_IRQ){
+ iic_interrupt_mode(dev, 0);
+ free_irq(dev->irq, dev);
+ dev->irq = NO_IRQ;
+ }
+ } else {
+ if (dev->irq != NO_IRQ){
+ iic_interrupt_mode(dev, 0);
+ free_irq(dev->irq, dev);
+ }
+ iounmap(dev->vaddr);
+ kfree(dev);
+ }
+
+ return 0;
+}
+
+
+static const struct of_device_id ibm_iic_match[] =
+{
+ { .type = "i2c", .compatible = "ibm,iic-405ex", },
+ { .type = "i2c", .compatible = "ibm,iic-405gp", },
+ { .type = "i2c", .compatible = "ibm,iic-440gp", },
+ { .type = "i2c", .compatible = "ibm,iic-440gpx", },
+ { .type = "i2c", .compatible = "ibm,iic-440grx", },
+ {}
+};
+
+static struct of_platform_driver ibm_iic_driver =
+{
+ .name = "ibm-iic",
+ .match_table = ibm_iic_match,
+ .probe = iic_probe,
+ .remove = iic_remove,
+};
+
+static int __init ibm_iic_init(void)
+{
+ printk(KERN_INFO "IBM IIC driver v" DRIVER_VERSION "\n");
+ return of_register_platform_driver(&ibm_iic_driver);
+}
+module_init(ibm_iic_init);
+
+static void __exit ibm_iic_exit(void)
+{
+ of_unregister_platform_driver(&ibm_iic_driver);
+}
+module_exit(ibm_iic_exit);
+#endif
^ permalink raw reply related
* [PATCH 1/3] [POWERPC] Implement support for the GPIO LIB API
From: Anton Vorontsov @ 2008-01-08 18:45 UTC (permalink / raw)
To: linuxppc-dev; +Cc: Arnd Bergmann, David Gibson
In-Reply-To: <20080108184341.GA29753@localhost.localdomain>
This patch implements support for the GPIO LIB API. Two calls
unimplemented though: irq_to_gpio and gpio_to_irq.
Various OF helpers provided to ease life and reduce code duplication.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
Documentation/powerpc/booting-without-of.txt | 58 ++++++++
arch/powerpc/Kconfig | 5 +
arch/powerpc/kernel/Makefile | 1 +
arch/powerpc/kernel/gpio.c | 186 ++++++++++++++++++++++++++
include/asm-powerpc/gpio.h | 126 +++++++++++++++++
5 files changed, 376 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/kernel/gpio.c
create mode 100644 include/asm-powerpc/gpio.h
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index ee0209a..dd2613c 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -60,6 +60,10 @@ Table of Contents
3) OpenPIC Interrupt Controllers
4) ISA Interrupt Controllers
+ VIII - Specifying GPIO information for devices
+ 1) gpios property
+ 2) gpio-controller nodes
+
Appendix A - Sample SOC node for MPC8540
@@ -2618,6 +2622,60 @@ encodings listed below:
2 = high to low edge sensitive type enabled
3 = low to high edge sensitive type enabled
+VIII - Specifying GPIO information for devices
+==============================================
+
+1) gpios property
+-----------------
+
+Nodes that makes use of GPIOs should define them using `gpios' property,
+format of which is: <&gpio-controller1-phandle gpio1-specifier
+ &gpio-controller2-phandle gpio2-specifier
+ ...>;
+
+Note that gpio-specifier length is controller dependent.
+
+gpio-specifier may encode: bank, pin position inside the bank,
+whether pin is open-drain and whether pin is active-low.
+
+Example of the node using GPIOs:
+
+ nand-flash@1,0 {
+ compatible = "stmicro,NAND512W3A2BN6E", "fsl,upm-nand";
+ reg = <1 0 1>;
+ width = <1>;
+ upm = "A";
+ upm-addr-offset = <16>;
+ upm-cmd-offset = <8>;
+ gpios = <&qe_pio_e 18>;
+ wait-pattern;
+ wait-write;
+ };
+
+In that example gpio-specifier is "18" and encodes GPIO pin number only,
+as accepted by the "qe_pio_e" gpio-controller.
+
+2) gpio-controller nodes
+------------------------
+
+Every GPIO controller node must have #gpio-cells property defined,
+this information will be used to translate gpio-specifiers.
+
+Example of two SOC GPIO banks defined as gpio-controller nodes:
+
+ qe_pio_a: gpio-controller@1400 {
+ #gpio-cells = <1>;
+ compatible = "fsl,qe-pario-bank";
+ reg = <0x1400 0x18>;
+ gpio-controller;
+ };
+
+ qe_pio_e: gpio-controller@1460 {
+ #gpio-cells = <1>;
+ compatible = "fsl,qe-pario-bank";
+ reg = <0x1460 0x18>;
+ gpio-controller;
+ };
Appendix A - Sample SOC node for MPC8540
========================================
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index 66a3d8c..b38c84a 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -73,6 +73,11 @@ config GENERIC_FIND_NEXT_BIT
bool
default y
+config GENERIC_GPIO
+ bool
+ help
+ Generic GPIO API support
+
config ARCH_NO_VIRT_TO_BUS
def_bool PPC64
diff --git a/arch/powerpc/kernel/Makefile b/arch/powerpc/kernel/Makefile
index 9374bc9..943045c 100644
--- a/arch/powerpc/kernel/Makefile
+++ b/arch/powerpc/kernel/Makefile
@@ -65,6 +65,7 @@ obj-$(CONFIG_BOOTX_TEXT) += btext.o
obj-$(CONFIG_SMP) += smp.o
obj-$(CONFIG_KPROBES) += kprobes.o
obj-$(CONFIG_PPC_UDBG_16550) += legacy_serial.o udbg_16550.o
+obj-$(CONFIG_GPIO_LIB) += gpio.o
pci64-$(CONFIG_PPC64) += pci_dn.o isa-bridge.o
obj-$(CONFIG_PCI) += pci_$(CONFIG_WORD_SIZE).o $(pci64-y) \
diff --git a/arch/powerpc/kernel/gpio.c b/arch/powerpc/kernel/gpio.c
new file mode 100644
index 0000000..f41d1e0
--- /dev/null
+++ b/arch/powerpc/kernel/gpio.c
@@ -0,0 +1,186 @@
+/*
+ * OF helpers for the GPIO API
+ *
+ * Copyright (c) 2007 MontaVista Software, Inc.
+ * Copyright (c) 2007 Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/of.h>
+#include <asm/prom.h>
+#include <asm/gpio.h>
+
+int of_gpio_simple_xlate(struct of_gpio_chip *of_gc, struct device_node *np,
+ const void *gpio_spec)
+{
+ const u32 *gpio = gpio_spec;
+
+ if (*gpio > of_gc->gc.ngpio)
+ return -EINVAL;
+
+ return *gpio;
+}
+EXPORT_SYMBOL(of_gpio_simple_xlate);
+
+int of_get_gpio(struct device_node *np, int index)
+{
+ int ret = -EINVAL;
+ struct device_node *gc;
+ struct of_gpio_chip *of_gc = NULL;
+ int size;
+ const u32 *gpios;
+ u32 nr_cells;
+ int i;
+ const void *gpio_spec;
+ const u32 *gpio_cells;
+ int gpio_index = 0;
+
+ gpios = of_get_property(np, "gpios", &size);
+ if (!gpios) {
+ ret = -ENOENT;
+ goto err0;
+ }
+ nr_cells = size / sizeof(u32);
+
+ for (i = 0; i < nr_cells;) {
+ const phandle *gpio_phandle;
+
+ gpio_phandle = gpios + i;
+ gpio_spec = gpio_phandle + 1;
+
+ gc = of_find_node_by_phandle(*gpio_phandle);
+ if (!gc) {
+ pr_debug("%s: could not find phandle for gpios\n",
+ np->full_name);
+ goto err0;
+ }
+
+ of_gc = gc->data;
+ if (!of_gc) {
+ pr_debug("%s: gpio controller %s isn't registered\n",
+ np->full_name, gc->full_name);
+ goto err1;
+ }
+
+ gpio_cells = of_get_property(gc, "#gpio-cells", &size);
+ if (!gpio_cells || size != sizeof(*gpio_cells) ||
+ *gpio_cells != of_gc->gpio_cells) {
+ pr_debug("%s: wrong #gpio-cells for %s\n",
+ np->full_name, gc->full_name);
+ goto err1;
+ }
+
+ /* Next phandle is at phandle cells + #gpio-cells */
+ i += sizeof(*gpio_phandle) / sizeof(u32) + *gpio_cells;
+ if (i >= nr_cells + 1) {
+ pr_debug("%s: insufficient gpio-spec length\n",
+ np->full_name);
+ goto err1;
+ }
+
+ if (gpio_index == index)
+ break;
+
+ of_gc = NULL;
+ of_node_put(gc);
+ gpio_index++;
+ }
+
+ if (!of_gc) {
+ ret = -ENOENT;
+ goto err0;
+ }
+
+ ret = of_gc->xlate(of_gc, np, gpio_spec);
+ if (ret < 0)
+ goto err1;
+
+ ret += of_gc->gc.base;
+err1:
+ of_node_put(gc);
+err0:
+ pr_debug("%s exited with status %d\n", __func__, ret);
+ return ret;
+}
+EXPORT_SYMBOL(of_get_gpio);
+
+static int of_get_gpiochip_base(struct device_node *np)
+{
+ struct device_node *gc = NULL;
+ int gpiochip_base = 0;
+
+ while ((gc = of_find_all_nodes(gc))) {
+ if (!of_get_property(gc, "gpio-controller", NULL))
+ continue;
+
+ if (gc != np) {
+ gpiochip_base += ARCH_GPIOS_PER_CHIP;
+ continue;
+ }
+
+ of_node_put(gc);
+
+ if (gpiochip_base >= ARCH_OF_GPIOS_END)
+ return -ENOSPC;
+
+ return gpiochip_base;
+ }
+
+ return -ENOENT;
+}
+
+int of_mm_gpiochip_add(struct device_node *np,
+ const struct of_gpio_chip *of_gc)
+{
+ int ret = -ENOMEM;
+ struct of_mm_gpio_chip *mm_gc;
+
+ mm_gc = kzalloc(sizeof(*mm_gc), GFP_KERNEL);
+ if (!mm_gc)
+ goto err0;
+
+ mm_gc->of_gc = *of_gc;
+
+ mm_gc->of_gc.gc.label = kstrdup(np->full_name, GFP_KERNEL);
+ if (!mm_gc->of_gc.gc.label)
+ goto err1;
+
+ ret = of_get_gpiochip_base(np);
+ if (ret < 0)
+ goto err2;
+
+ mm_gc->regs = of_iomap(np, 0);
+ if (!mm_gc->regs) {
+ ret = -ENOMEM;
+ goto err1;
+ }
+
+ mm_gc->of_gc.gc.base = ret;
+
+ np->data = &mm_gc->of_gc;
+
+ ret = gpiochip_add(&mm_gc->of_gc.gc);
+ if (ret)
+ goto err2;
+
+ of_node_get(np);
+
+ pr_debug("%s: registered as generic GPIO chip, base is %d\n",
+ np->full_name, mm_gc->of_gc.gc.base);
+ return 0;
+err2:
+ np->data = NULL;
+ kfree(mm_gc->of_gc.gc.label);
+err1:
+ kfree(mm_gc);
+err0:
+ pr_err("%s: GPIO chip registration failed with status %d\n",
+ np->full_name, ret);
+ return ret;
+}
+EXPORT_SYMBOL(of_mm_gpiochip_add);
diff --git a/include/asm-powerpc/gpio.h b/include/asm-powerpc/gpio.h
new file mode 100644
index 0000000..1cc2e90
--- /dev/null
+++ b/include/asm-powerpc/gpio.h
@@ -0,0 +1,126 @@
+/*
+ * Generic GPIO API implementation for PowerPC.
+ *
+ * Copyright (c) 2007 MontaVista Software, Inc.
+ * Copyright (c) 2007 Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __ASM_POWERPC_GPIO_H
+#define __ASM_POWERPC_GPIO_H
+
+#include <asm-generic/gpio.h>
+
+#ifdef CONFIG_GPIO_LIB
+
+#define ARCH_OF_GPIOS_BASE 0
+#define ARCH_OF_GPIOS_END (ARCH_GPIOS_PER_CHIP * 7)
+#define ARCH_NON_OF_GPIOS_BASE ARCH_OF_GPIOS_END
+#define ARCH_NON_OF_GPIOS_END ARCH_NR_GPIOS
+
+#if ARCH_NON_OF_GPIOS_BASE >= ARCH_NON_OF_GPIOS_END
+#error "Default ARCH_NR_GPIOS isn't sufficient, define yours."
+#endif
+
+/*
+ * We don't (yet) implement inlined/rapid versions for on-chip gpios.
+ * Just call gpiolib.
+ */
+static inline int gpio_get_value(unsigned int gpio)
+{
+ return __gpio_get_value(gpio);
+}
+
+static inline void gpio_set_value(unsigned int gpio, int value)
+{
+ __gpio_set_value(gpio, value);
+}
+
+/*
+ * Not implemented, yet.
+ */
+static inline int gpio_to_irq(unsigned int gpio)
+{
+ return -ENOSYS;
+}
+
+static inline int irq_to_gpio(unsigned int irq)
+{
+ return -ENOSYS;
+}
+
+/*
+ * Generic OF GPIO chip
+ */
+struct of_gpio_chip {
+ struct gpio_chip gc;
+ int gpio_cells;
+ int (*xlate)(struct of_gpio_chip *of_gc, struct device_node *np,
+ const void *gpio_spec);
+};
+
+#define to_of_gpio_chip(x) container_of(x, struct of_gpio_chip, gc)
+
+/*
+ * OF GPIO chip for memory mapped banks
+ */
+struct of_mm_gpio_chip {
+ struct of_gpio_chip of_gc;
+ void __iomem *regs;
+};
+
+#define to_of_mm_gpio_chip(x) container_of(to_of_gpio_chip(x), \
+ struct of_mm_gpio_chip, of_gc)
+
+/**
+ * of_gpio_simple_xlate - Translate GPIO number given in the device tree
+ * @of_gc: pointer to the OF GPIO chip
+ * @np: device node to get GPIO from
+ * @gpio_spec: pointer to the gpio-spec field in the `gpios' property
+ *
+ * This is gpio-controller specific function, returns translated GPIO
+ * number.
+ */
+extern int of_gpio_simple_xlate(struct of_gpio_chip *of_gc,
+ struct device_node *np,
+ const void *gpio_spec);
+
+/**
+ * of_get_gpio - Get a GPIO number from the device tree to use with GPIO API
+ * @np: device node to get GPIO from
+ * @index: index of the GPIO
+ *
+ * Returns GPIO number to use with Linux generic GPIO API, or one of the errno
+ * value on the error condition.
+ */
+extern int of_get_gpio(struct device_node *np, int index);
+
+/**
+ * of_mm_gpiochip_add - Add memory mapped GPIO chip (bank)
+ * @np: device node of the GPIO chip
+ * @of_gc: pointer to the of_gpio_chip template
+ *
+ * To use this function you should fill of_gc template with:
+ *
+ * 1) In the gpio_chip structure:
+ * a) all callbacks
+ * b) ngpios (GPIOs per bank)
+ *
+ * 2) In the of_gpio_chip structure:
+ * a) xlate callback
+ * b) gpio_cells
+ *
+ * If succeeded, this function will map bank's memory and will
+ * do all necessary work for you. Then you'll able to use .regs
+ * to manage GPIOs from the callbacks.
+ */
+extern int of_mm_gpiochip_add(struct device_node *np,
+ const struct of_gpio_chip *of_gc);
+
+#endif /* CONFIG_GPIO_LIB */
+
+#endif /* __ASM_POWERPC_GPIO_H */
--
1.5.2.2
^ permalink raw reply related
* [PATCH 2/3] [POWERPC] QE: split par_io_config_pin()
From: Anton Vorontsov @ 2008-01-08 18:45 UTC (permalink / raw)
To: linuxppc-dev; +Cc: Arnd Bergmann, David Gibson
In-Reply-To: <20080108184341.GA29753@localhost.localdomain>
This patch splits par_io_config_pin so we can use it with GPIO LIB API.
Also add a comment regarding #ifdef CONFIG_PPC_85xx being legacy.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
arch/powerpc/sysdev/qe_lib/qe_io.c | 60 +++++++++++++++++++++++------------
1 files changed, 39 insertions(+), 21 deletions(-)
diff --git a/arch/powerpc/sysdev/qe_lib/qe_io.c b/arch/powerpc/sysdev/qe_lib/qe_io.c
index e53ea4d..aef893b 100644
--- a/arch/powerpc/sysdev/qe_lib/qe_io.c
+++ b/arch/powerpc/sysdev/qe_lib/qe_io.c
@@ -37,6 +37,10 @@ struct port_regs {
__be32 cppar1; /* Pin assignment register */
__be32 cppar2; /* Pin assignment register */
#ifdef CONFIG_PPC_85xx
+ /*
+ * This is needed for legacy support only, should go away,
+ * because we started using per-bank gpio chips.
+ */
u8 pad[8];
#endif
};
@@ -63,28 +67,29 @@ int par_io_init(struct device_node *np)
return 0;
}
-int par_io_config_pin(u8 port, u8 pin, int dir, int open_drain,
- int assignment, int has_irq)
+static void __par_io_config_pin(struct port_regs __iomem *par_io,
+ u8 pin, int dir, int open_drain,
+ int assignment, int has_irq)
{
- u32 pin_mask1bit, pin_mask2bits, new_mask2bits, tmp_val;
-
- if (!par_io)
- return -1;
+ u32 pin_mask1bit;
+ u32 pin_mask2bits;
+ u32 new_mask2bits;
+ u32 tmp_val;
/* calculate pin location for single and 2 bits information */
pin_mask1bit = (u32) (1 << (NUM_OF_PINS - (pin + 1)));
/* Set open drain, if required */
- tmp_val = in_be32(&par_io[port].cpodr);
+ tmp_val = in_be32(&par_io->cpodr);
if (open_drain)
- out_be32(&par_io[port].cpodr, pin_mask1bit | tmp_val);
+ out_be32(&par_io->cpodr, pin_mask1bit | tmp_val);
else
- out_be32(&par_io[port].cpodr, ~pin_mask1bit & tmp_val);
+ out_be32(&par_io->cpodr, ~pin_mask1bit & tmp_val);
/* define direction */
tmp_val = (pin > (NUM_OF_PINS / 2) - 1) ?
- in_be32(&par_io[port].cpdir2) :
- in_be32(&par_io[port].cpdir1);
+ in_be32(&par_io->cpdir2) :
+ in_be32(&par_io->cpdir1);
/* get all bits mask for 2 bit per port */
pin_mask2bits = (u32) (0x3 << (NUM_OF_PINS -
@@ -96,36 +101,49 @@ int par_io_config_pin(u8 port, u8 pin, int dir, int open_drain,
/* clear and set 2 bits mask */
if (pin > (NUM_OF_PINS / 2) - 1) {
- out_be32(&par_io[port].cpdir2,
+ out_be32(&par_io->cpdir2,
~pin_mask2bits & tmp_val);
tmp_val &= ~pin_mask2bits;
- out_be32(&par_io[port].cpdir2, new_mask2bits | tmp_val);
+ out_be32(&par_io->cpdir2, new_mask2bits | tmp_val);
} else {
- out_be32(&par_io[port].cpdir1,
+ out_be32(&par_io->cpdir1,
~pin_mask2bits & tmp_val);
tmp_val &= ~pin_mask2bits;
- out_be32(&par_io[port].cpdir1, new_mask2bits | tmp_val);
+ out_be32(&par_io->cpdir1, new_mask2bits | tmp_val);
}
/* define pin assignment */
tmp_val = (pin > (NUM_OF_PINS / 2) - 1) ?
- in_be32(&par_io[port].cppar2) :
- in_be32(&par_io[port].cppar1);
+ in_be32(&par_io->cppar2) :
+ in_be32(&par_io->cppar1);
new_mask2bits = (u32) (assignment << (NUM_OF_PINS -
(pin % (NUM_OF_PINS / 2) + 1) * 2));
/* clear and set 2 bits mask */
if (pin > (NUM_OF_PINS / 2) - 1) {
- out_be32(&par_io[port].cppar2,
+ out_be32(&par_io->cppar2,
~pin_mask2bits & tmp_val);
tmp_val &= ~pin_mask2bits;
- out_be32(&par_io[port].cppar2, new_mask2bits | tmp_val);
+ out_be32(&par_io->cppar2, new_mask2bits | tmp_val);
} else {
- out_be32(&par_io[port].cppar1,
+ out_be32(&par_io->cppar1,
~pin_mask2bits & tmp_val);
tmp_val &= ~pin_mask2bits;
- out_be32(&par_io[port].cppar1, new_mask2bits | tmp_val);
+ out_be32(&par_io->cppar1, new_mask2bits | tmp_val);
}
+}
+
+/*
+ * This is "legacy" function that takes port number as an argument
+ * instead of pointer to the appropriate bank.
+ */
+int par_io_config_pin(u8 port, u8 pin, int dir, int open_drain,
+ int assignment, int has_irq)
+{
+ if (!par_io || port >= num_par_io_ports)
+ return -EINVAL;
+ __par_io_config_pin(&par_io[port], pin, dir, open_drain, assignment,
+ has_irq);
return 0;
}
EXPORT_SYMBOL(par_io_config_pin);
--
1.5.2.2
^ permalink raw reply related
* [PATCH 3/3] [POWERPC] QE: implement GPIO LIB API
From: Anton Vorontsov @ 2008-01-08 18:45 UTC (permalink / raw)
To: linuxppc-dev; +Cc: Arnd Bergmann, David Gibson
In-Reply-To: <20080108184341.GA29753@localhost.localdomain>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
Documentation/powerpc/booting-without-of.txt | 32 +++++++----
arch/powerpc/platforms/Kconfig | 2 +
arch/powerpc/sysdev/qe_lib/qe_io.c | 73 ++++++++++++++++++++++++++
include/asm-powerpc/qe.h | 1 +
4 files changed, 96 insertions(+), 12 deletions(-)
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index dd2613c..e279152 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -1696,24 +1696,32 @@ platforms are moved over to use the flattened-device-tree model.
information.
Required properties:
- - device_type : should be "par_io".
+ - #gpio-cells : should be "1".
+ - compatible : should be "fsl,qe-pario-bank"
- reg : offset to the register set and its length.
- - num-ports : number of Parallel I/O ports
+ - gpio-controller : node to identify gpio controllers.
- Example:
- par_io@1400 {
- reg = <1400 100>;
- #address-cells = <1>;
- #size-cells = <0>;
- device_type = "par_io";
- num-ports = <7>;
- ucc_pin@01 {
- ......
- };
+ For example, two QE Par I/O banks:
+ qe_pio_a: gpio-controller@1400 {
+ #gpio-cells = <1>;
+ compatible = "fsl,qe-pario-bank";
+ reg = <0x1400 0x18>;
+ gpio-controller;
+ };
+ qe_pio_e: gpio-controller@1460 {
+ #gpio-cells = <1>;
+ compatible = "fsl,qe-pario-bank";
+ reg = <0x1460 0x18>;
+ gpio-controller;
+ };
vi) Pin configuration nodes
+ NOTE: pin configuration nodes are obsolete. Usually, their existance
+ is an evidence of the firmware shortcomings. Such fixups are
+ better handled by the Linux board file, not the device tree.
+
Required properties:
- linux,phandle : phandle of this node; likely referenced by a QE
device.
diff --git a/arch/powerpc/platforms/Kconfig b/arch/powerpc/platforms/Kconfig
index ea22cad..8dff946 100644
--- a/arch/powerpc/platforms/Kconfig
+++ b/arch/powerpc/platforms/Kconfig
@@ -265,6 +265,8 @@ config TAU_AVERAGE
config QUICC_ENGINE
bool
select PPC_LIB_RHEAP
+ select GENERIC_GPIO
+ select GPIO_LIB
help
The QUICC Engine (QE) is a new generation of communications
coprocessors on Freescale embedded CPUs (akin to CPM in older chips).
diff --git a/arch/powerpc/sysdev/qe_lib/qe_io.c b/arch/powerpc/sysdev/qe_lib/qe_io.c
index aef893b..2a1ff45 100644
--- a/arch/powerpc/sysdev/qe_lib/qe_io.c
+++ b/arch/powerpc/sysdev/qe_lib/qe_io.c
@@ -23,6 +23,7 @@
#include <asm/io.h>
#include <asm/prom.h>
+#include <asm/gpio.h>
#include <sysdev/fsl_soc.h>
#undef DEBUG
@@ -213,6 +214,78 @@ int par_io_of_config(struct device_node *np)
}
EXPORT_SYMBOL(par_io_of_config);
+/*
+ * GPIO LIB API implementation
+ */
+
+static int qe_gpio_get(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct port_regs *regs = mm_gc->regs;
+ u32 pin_mask;
+
+ /* calculate pin location */
+ pin_mask = (u32) (1 << (NUM_OF_PINS - 1 - gpio));
+
+ return !!(in_be32(®s->cpdata) & pin_mask);
+}
+
+static void qe_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct port_regs *regs = mm_gc->regs;
+ u32 pin_mask;
+ u32 tmp_val;
+
+ /* calculate pin location */
+ pin_mask = (u32) (1 << (NUM_OF_PINS - 1 - gpio));
+
+ tmp_val = in_be32(®s->cpdata);
+
+ if (val == 0)
+ out_be32(®s->cpdata, ~pin_mask & tmp_val);
+ else
+ out_be32(®s->cpdata, pin_mask | tmp_val);
+}
+
+static int qe_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+
+ __par_io_config_pin(mm_gc->regs, gpio, 2, 0, 0, 0);
+
+ return 0;
+}
+
+static int qe_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+
+ __par_io_config_pin(mm_gc->regs, gpio, 1, 0, 0, 0);
+ qe_gpio_set(gc, gpio, val);
+
+ return 0;
+}
+
+static struct of_gpio_chip qe_gc = {
+ .gpio_cells = 1,
+ .xlate = of_gpio_simple_xlate,
+
+ .gc = {
+ .ngpio = NUM_OF_PINS,
+ .direction_input = qe_gpio_dir_in,
+ .direction_output = qe_gpio_dir_out,
+ .get = qe_gpio_get,
+ .set = qe_gpio_set,
+ },
+};
+
+int qe_gpiochip_add(struct device_node *np)
+{
+ return of_mm_gpiochip_add(np, &qe_gc);
+}
+EXPORT_SYMBOL(qe_gpiochip_add);
+
#ifdef DEBUG
static void dump_par_io(void)
{
diff --git a/include/asm-powerpc/qe.h b/include/asm-powerpc/qe.h
index a24b7b1..2efda82 100644
--- a/include/asm-powerpc/qe.h
+++ b/include/asm-powerpc/qe.h
@@ -77,6 +77,7 @@ enum qe_clock {
/* Export QE common operations */
extern void qe_reset(void);
extern int par_io_init(struct device_node *np);
+extern int qe_gpiochip_add(struct device_node *np);
extern int par_io_of_config(struct device_node *np);
extern int par_io_config_pin(u8 port, u8 pin, int dir, int open_drain,
int assignment, int has_irq);
--
1.5.2.2
^ permalink raw reply related
* Re: [PATCH] Miscellaneous for Taco
From: Sean MacLennan @ 2008-01-08 18:41 UTC (permalink / raw)
To: benh; +Cc: linuxppc-dev, Stefan Roese
In-Reply-To: <1199566583.7291.63.camel@pasglop>
How about just 44x?
Cheers,
Sean
diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
index 7580aa5..682deae 100644
--- a/drivers/usb/Kconfig
+++ b/drivers/usb/Kconfig
@@ -39,6 +39,7 @@ config USB_ARCH_HAS_OHCI
# PPC:
default y if STB03xxx
default y if PPC_MPC52xx
+ default y if 44x
# MIPS:
default y if SOC_AU1X00
# more:
^ permalink raw reply related
* Re: [PATCH RFC 0/3] PowerPC: implement support for GPIO LIB API
From: Grant Likely @ 2008-01-08 18:50 UTC (permalink / raw)
To: avorontsov; +Cc: Arnd Bergmann, linuxppc-dev, David Gibson
In-Reply-To: <20080108184341.GA29753@localhost.localdomain>
On 1/8/08, Anton Vorontsov <avorontsov@ru.mvista.com> wrote:
> Hi all,
>
> Thanks for the previous review and ideas. Here is the RFC for the
> GPIO LIB support.
I like this layout for gpios. It's concise and compact. It will work
well for my gpio driver also.
>
> I'm using it like this:
>
> qe_pio_a: gpio-controller@1400 {
> #gpio-cells = <1>;
> compatible = "fsl,qe-pario-bank";
Here's my only comment: Compatible should have "fsl,<chip>-pario-bank"
first. Be specific for the first value of the compatible property.
You can add generic names after the specific one if you like, but it's
hard to come up with a generic name when you don't know what a
manufacture is going to do with it's marketing names in the future.
> reg = <0x1400 0x18>;
> gpio-controller;
> };
>
> qe_pio_e: gpio-controller@1460 {
> #gpio-cells = <1>;
> compatible = "fsl,qe-pario-bank";
> reg = <0x1460 0x18>;
> gpio-controller;
> };
>
> nand-flash@1,0 {
> compatible = "stmicro,NAND512W3A2BN6E", "fsl,upm-nand";
> reg = <1 0 1>;
> width = <1>;
> upm = "A";
> upm-addr-offset = <16>;
> upm-cmd-offset = <8>;
> gpios = <&qe_pio_e 18 &qe_pio_a 9>;
> wait-pattern;
> wait-write;
> };
>
> As you can see I've split single "par_io" node into banks, thus
> the benefits:
> - we can handle banks of different width (Jochen Friedrich asked for
> this, IIRC. Or I've misunderstood ;-).
> - we can handle banks with different paddings (no more #ifdef PPC85xx).
>
> Also, it's possible to specify different gpio-controllers in the
> gpios = <> property. gpio-specifier is controller specific.
>
>
> The remaining question is about gpio.c placement. prom_parse.c doesn't
> feel as the appropriate place anymore. I think of:
>
> - drivers/gpio/of_gpio.c (driver/gpio/ is in -mm tree);
> - drivers/of/gpio.c
> - keep it in arch/powerpc/kernel/ (though, there is nothing
> much PowerPC specific).
>
>
> So, to try these patches you'll need apply these from the -mm tree:
> generic-gpio-gpio_chip-support.patch
> generic-gpio-gpio_chip-support-fix.patch
> generic-gpio-gpio_chip-support-gpiolib-locking-simplified.patch
>
> Or just issue this in your working tree:
>
> git pull git://git.infradead.org/users/cbou/powerpc-gpio.git gpiolib
>
> powerpc-gpio.git's gpiolib branch is galak/powerpc.git master branch +
> -mm patches + these patches.
>
>
> Support for CPM2 is pending.
>
> Thanks!
>
> --
> Anton Vorontsov
> email: cbou@mail.ru
> backup email: ya-cbou@yandex.ru
> irc://irc.freenode.net/bd2
>
--
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
^ permalink raw reply
* [PATCH for 2.6.24][NET] fs_enet: check for phydev existence in the ethtool handlers
From: Anton Vorontsov @ 2008-01-08 19:05 UTC (permalink / raw)
To: Jeff Garzik; +Cc: netdev, linuxppc-dev
Otherwise oops will happen if ethernet device has not been opened:
Unable to handle kernel paging request for data at address 0x0000014c
Faulting instruction address: 0xc016f7f0
Oops: Kernel access of bad area, sig: 11 [#1]
MPC85xx
NIP: c016f7f0 LR: c01722a0 CTR: 00000000
REGS: c79ddc70 TRAP: 0300 Not tainted (2.6.24-rc3-g820a386b)
MSR: 00029000 <EE,ME> CR: 20004428 XER: 20000000
DEAR: 0000014c, ESR: 00000000
TASK = c789f5e0[999] 'snmpd' THREAD: c79dc000
GPR00: c01aceb8 c79ddd20 c789f5e0 00000000 c79ddd3c 00000000 c79ddd64 00000000
GPR08: 00000000 c7845b60 c79dde3c c01ace80 20004422 200249fc 000002a0 100da728
GPR16: 100c0000 00000000 00000000 00000000 20022078 00000009 200220e0 bfc85558
GPR24: c79ddd3c 00000000 00000000 c02e0e70 c022fc64 ffffffff c7845800 bfc85498
NIP [c016f7f0] phy_ethtool_gset+0x0/0x4c
LR [c01722a0] fs_get_settings+0x18/0x28
Call Trace:
[c79ddd20] [c79dde38] 0xc79dde38 (unreliable)
[c79ddd30] [c01aceb8] dev_ethtool+0x294/0x11ec
[c79dde30] [c01aaa44] dev_ioctl+0x454/0x6a8
[c79ddeb0] [c019b9d4] sock_ioctl+0x84/0x230
[c79dded0] [c007ded8] do_ioctl+0x34/0x8c
[c79ddee0] [c007dfbc] vfs_ioctl+0x8c/0x41c
[c79ddf10] [c007e38c] sys_ioctl+0x40/0x74
[c79ddf40] [c000d4c0] ret_from_syscall+0x0/0x3c
Instruction dump:
81630000 800b0030 2f800000 419e0010 7c0803a6 4e800021 7c691b78 80010014
7d234b78 38210010 7c0803a6 4e800020 <8003014c> 7c6b1b78 38600000 90040004
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Vitaly Bordug <vitb@kernel.crashing.org>
---
Just resending it, it feels like it got lost during holidays.
drivers/net/fs_enet/fs_enet-main.c | 11 +++++++++--
1 files changed, 9 insertions(+), 2 deletions(-)
diff --git a/drivers/net/fs_enet/fs_enet-main.c b/drivers/net/fs_enet/fs_enet-main.c
index f2a4d39..23fddc3 100644
--- a/drivers/net/fs_enet/fs_enet-main.c
+++ b/drivers/net/fs_enet/fs_enet-main.c
@@ -897,14 +897,21 @@ static void fs_get_regs(struct net_device *dev, struct ethtool_regs *regs,
static int fs_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
{
struct fs_enet_private *fep = netdev_priv(dev);
+
+ if (!fep->phydev)
+ return -ENODEV;
+
return phy_ethtool_gset(fep->phydev, cmd);
}
static int fs_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
{
struct fs_enet_private *fep = netdev_priv(dev);
- phy_ethtool_sset(fep->phydev, cmd);
- return 0;
+
+ if (!fep->phydev)
+ return -ENODEV;
+
+ return phy_ethtool_sset(fep->phydev, cmd);
}
static int fs_nway_reset(struct net_device *dev)
--
1.5.2.2
^ permalink raw reply related
* Re: Base Warp Platform support
From: Sean MacLennan @ 2008-01-08 18:58 UTC (permalink / raw)
To: benh; +Cc: linuxppc-dev
In-Reply-To: <1199517639.7291.45.camel@pasglop>
It has come down from on high that the taco will henceforth be know as
the Warp(tm). So here are updated patches with the "great name change".
I have also merged the NOR flash partitions into the dts file.
Cheers,
Sean
^ permalink raw reply
* Re: [PATCH 1/2] Base Warp Platform support
From: Sean MacLennan @ 2008-01-08 18:59 UTC (permalink / raw)
To: benh; +Cc: linuxppc-dev
In-Reply-To: <1199517639.7291.45.camel@pasglop>
*diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index 66a3d8c..b3e4c35 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -469,7 +469,7 @@ config MCA
config PCI
bool "PCI support" if 40x || CPM2 || PPC_83xx || PPC_85xx || PPC_86xx \
|| PPC_MPC52xx || (EMBEDDED && (PPC_PSERIES || PPC_ISERIES)) \
- || PPC_PS3
+ || PPC_PS3 || 44x
default y if !40x && !CPM2 && !8xx && !PPC_83xx \
&& !PPC_85xx && !PPC_86xx
default PCI_PERMEDIA if !4xx && !CPM2 && !8xx
diff --git a/arch/powerpc/boot/44x.h b/arch/powerpc/boot/44x.h
index 0256344..9db0213 100644
--- a/arch/powerpc/boot/44x.h
+++ b/arch/powerpc/boot/44x.h
@@ -12,5 +12,6 @@
void ebony_init(void *mac0, void *mac1);
void bamboo_init(void *mac0, void *mac1);
+void warp_init(void *mac0, void *mac1);
#endif /* _PPC_BOOT_44X_H_ */
diff --git a/arch/powerpc/boot/Makefile b/arch/powerpc/boot/Makefile
index d1e625c..df0ef6f 100644
--- a/arch/powerpc/boot/Makefile
+++ b/arch/powerpc/boot/Makefile
@@ -56,13 +56,13 @@ src-wlib := string.S crt0.S stdio.c main.c \
gunzip_util.c elf_util.c $(zlib) devtree.c oflib.c ofconsole.c \
4xx.c ebony.c mv64x60.c mpsc.c mv64x60_i2c.c cuboot.c bamboo.c \
cpm-serial.c stdlib.c mpc52xx-psc.c planetcore.c uartlite.c \
- fsl-soc.c mpc8xx.c pq2.c
+ fsl-soc.c mpc8xx.c pq2.c warp.c
src-plat := of.c cuboot-52xx.c cuboot-83xx.c cuboot-85xx.c holly.c \
cuboot-ebony.c treeboot-ebony.c prpmc2800.c \
ps3-head.S ps3-hvcall.S ps3.c treeboot-bamboo.c cuboot-8xx.c \
cuboot-pq2.c cuboot-sequoia.c treeboot-walnut.c cuboot-bamboo.c \
fixed-head.S ep88xc.c cuboot-hpc2.c ep405.c cuboot-taishan.c \
- cuboot-katmai.c cuboot-rainier.c
+ cuboot-katmai.c cuboot-rainier.c cuboot-warp.c
src-boot := $(src-wlib) $(src-plat) empty.c
src-boot := $(addprefix $(obj)/, $(src-boot))
@@ -206,6 +206,7 @@ image-$(CONFIG_RAINIER) += cuImage.rainier
image-$(CONFIG_WALNUT) += treeImage.walnut
image-$(CONFIG_TAISHAN) += cuImage.taishan
image-$(CONFIG_KATMAI) += cuImage.katmai
+image-$(CONFIG_WARP) += cuImage.warp
endif
# For 32-bit powermacs, build the COFF and miboot images
diff --git a/arch/powerpc/kernel/cputable.c b/arch/powerpc/kernel/cputable.c
index f1928af..ece0c71 100644
--- a/arch/powerpc/kernel/cputable.c
+++ b/arch/powerpc/kernel/cputable.c
@@ -1226,6 +1226,18 @@ static struct cpu_spec __initdata cpu_specs[] = {
.machine_check = machine_check_4xx,
.platform = "ppc440",
},
+ { /* Matches both physical and logical PVR for 440EP (logical pvr = pvr | 0x8) */
+ .pvr_mask = 0xf0000ff7,
+ .pvr_value = 0x400008d4,
+ .cpu_name = "440EP Rev. C",
+ .cpu_features = CPU_FTRS_44X,
+ .cpu_user_features = COMMON_USER_BOOKE | PPC_FEATURE_HAS_FPU,
+ .icache_bsize = 32,
+ .dcache_bsize = 32,
+ .cpu_setup = __setup_cpu_440ep,
+ .machine_check = machine_check_4xx,
+ .platform = "ppc440",
+ },
{ /* Use logical PVR for 440EP (logical pvr = pvr | 0x8) */
.pvr_mask = 0xf0000fff,
.pvr_value = 0x400008db,
diff --git a/arch/powerpc/platforms/44x/Kconfig b/arch/powerpc/platforms/44x/Kconfig
index d248013..21152e5 100644
--- a/arch/powerpc/platforms/44x/Kconfig
+++ b/arch/powerpc/platforms/44x/Kconfig
@@ -53,6 +53,19 @@ config RAINIER
help
This option enables support for the AMCC PPC440GRX evaluation board.
+config WARP
+ bool "PIKA Warp"
+ depends on 44x
+ default n
+ select 440EP
+ help
+ This option enables support for the PIKA Warp(tm) Appliance. The Warp
+ is a small computer replacement with up to 9 ports of FXO/FXS plus VOIP
+ stations and trunks.
+
+ See http://www.pikatechnologies.com/ and follow the "PIKA for Computer
+ Telephony Developers" link for more information.
+
#config LUAN
# bool "Luan"
# depends on 44x
diff --git a/arch/powerpc/platforms/44x/Makefile b/arch/powerpc/platforms/44x/Makefile
index a2a0dc1..c1733c0 100644
--- a/arch/powerpc/platforms/44x/Makefile
+++ b/arch/powerpc/platforms/44x/Makefile
@@ -5,3 +5,4 @@ obj-$(CONFIG_BAMBOO) += bamboo.o
obj-$(CONFIG_SEQUOIA) += sequoia.o
obj-$(CONFIG_KATMAI) += katmai.o
obj-$(CONFIG_RAINIER) += rainier.o
+obj-$(CONFIG_WARP) += warp.o
--- /dev/null 2005-11-20 22:22:37.000000000 -0500
+++ arch/powerpc/configs/warp_defconfig 2008-01-08 12:30:27.000000000 -0500
@@ -0,0 +1,1057 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.24-rc6
+# Tue Jan 8 12:23:23 2008
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+# CONFIG_6xx is not set
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+CONFIG_44x=y
+# CONFIG_E200 is not set
+CONFIG_PPC_FPU=y
+CONFIG_4xx=y
+CONFIG_BOOKE=y
+CONFIG_PTE_64BIT=y
+CONFIG_PHYS_64BIT=y
+# CONFIG_PPC_MM_SLICES is not set
+CONFIG_NOT_COHERENT_CACHE=y
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+CONFIG_PPC_UDBG_16550=y
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+CONFIG_PPC_DCR_NATIVE=y
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_PPC_DCR=y
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION="-pika"
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+# CONFIG_HOTPLUG is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+# CONFIG_BAMBOO is not set
+# CONFIG_EBONY is not set
+# CONFIG_SEQUOIA is not set
+# CONFIG_TAISHAN is not set
+# CONFIG_KATMAI is not set
+# CONFIG_RAINIER is not set
+CONFIG_WARP=y
+CONFIG_440EP=y
+CONFIG_IBM440EP_ERR42=y
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPM2 is not set
+# CONFIG_FSL_ULI1575 is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+# CONFIG_HZ_250 is not set
+# CONFIG_HZ_300 is not set
+CONFIG_HZ_1000=y
+CONFIG_HZ=1000
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_MATH_EMULATION is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+CONFIG_RESOURCES_64BIT=y
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+CONFIG_PROC_DEVICETREE=y
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="ip=on"
+CONFIG_SECCOMP=y
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE="warp.dts"
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0xc0000000
+CONFIG_CONSISTENT_START=0xff100000
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_BOOT_LOAD=0x01000000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IP_VS is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+CONFIG_NETFILTER=y
+# CONFIG_NETFILTER_DEBUG is not set
+
+#
+# Core Netfilter Configuration
+#
+# CONFIG_NETFILTER_NETLINK is not set
+# CONFIG_NF_CONNTRACK_ENABLED is not set
+# CONFIG_NF_CONNTRACK is not set
+# CONFIG_NETFILTER_XTABLES is not set
+
+#
+# IP: Netfilter Configuration
+#
+# CONFIG_IP_NF_QUEUE is not set
+# CONFIG_IP_NF_IPTABLES is not set
+# CONFIG_IP_NF_ARPTABLES is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+CONFIG_VLAN_8021Q=y
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+# CONFIG_STANDALONE is not set
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+CONFIG_MTD_OOPS=m
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+CONFIG_MTD_NAND_ECC_SMC=y
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+CONFIG_MTD_NAND_IDS=y
+CONFIG_MTD_NAND_NDFC=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+# CONFIG_MTD_ALAUDA is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+# CONFIG_BLK_DEV_LOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_UB is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=4096
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_XILINX_SYSACE is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=y
+CONFIG_SCSI_DMA=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=y
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+# CONFIG_CHR_DEV_SG is not set
+# CONFIG_CHR_DEV_SCH is not set
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+# CONFIG_SCSI_WAIT_SCAN is not set
+
+#
+# SCSI Transports
+#
+CONFIG_SCSI_SPI_ATTRS=y
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
+# CONFIG_SCSI_LOWLEVEL is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+CONFIG_IBM_NEW_EMAC=y
+CONFIG_IBM_NEW_EMAC_RXB=128
+CONFIG_IBM_NEW_EMAC_TXB=64
+CONFIG_IBM_NEW_EMAC_POLL_WEIGHT=32
+CONFIG_IBM_NEW_EMAC_RX_COPY_THRESHOLD=256
+CONFIG_IBM_NEW_EMAC_RX_SKB_HEADROOM=0
+# CONFIG_IBM_NEW_EMAC_DEBUG is not set
+CONFIG_IBM_NEW_EMAC_ZMII=y
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_B44 is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_8250_EXTENDED=y
+# CONFIG_SERIAL_8250_MANY_PORTS is not set
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+# CONFIG_SERIAL_8250_DETECT_IRQ is not set
+# CONFIG_SERIAL_8250_RSA is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_OF_PLATFORM is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_NVRAM is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+# CONFIG_I2C_CHARDEV is not set
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+CONFIG_I2C_IBM_IIC=y
+# CONFIG_I2C_MPC is not set
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_SIMTEC is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_TINY_USB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_SENSORS_DS1337 is not set
+# CONFIG_SENSORS_DS1374 is not set
+# CONFIG_DS1682 is not set
+CONFIG_SENSORS_EEPROM=y
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_M41T00 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+CONFIG_SENSORS_AD7414=y
+# CONFIG_SENSORS_AD7418 is not set
+# CONFIG_SENSORS_ADM1021 is not set
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1029 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ADT7470 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_F75375S is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM75 is not set
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_LM93 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_MAX6650 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_DME1737 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47M192 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83791D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+
+#
+# Miscellaneous USB options
+#
+# CONFIG_USB_DEVICEFS is not set
+CONFIG_USB_DEVICE_CLASS=y
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_OTG is not set
+
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_ISP116X_HCD is not set
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_HCD_PPC_OF=y
+CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
+# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
+CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
+CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
+CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+# CONFIG_USB_SL811_HCD is not set
+# CONFIG_USB_R8A66597_HCD is not set
+
+#
+# USB Device Class drivers
+#
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_PRINTER is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# may also be needed; see USB_STORAGE Help for more information
+#
+CONFIG_USB_STORAGE=y
+# CONFIG_USB_STORAGE_DEBUG is not set
+# CONFIG_USB_STORAGE_DATAFAB is not set
+# CONFIG_USB_STORAGE_FREECOM is not set
+# CONFIG_USB_STORAGE_ISD200 is not set
+# CONFIG_USB_STORAGE_DPCM is not set
+# CONFIG_USB_STORAGE_USBAT is not set
+# CONFIG_USB_STORAGE_SDDR09 is not set
+# CONFIG_USB_STORAGE_SDDR55 is not set
+# CONFIG_USB_STORAGE_JUMPSHOT is not set
+# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+CONFIG_USB_MON=y
+
+#
+# USB port drivers
+#
+
+#
+# USB Serial Converter support
+#
+# CONFIG_USB_SERIAL is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_AUERSWALD is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_PHIDGET is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
+
+#
+# USB DSL modem support
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+CONFIG_MMC=m
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD Card Drivers
+#
+CONFIG_MMC_BLOCK=m
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+
+#
+# MMC/SD Host Controller Drivers
+#
+# CONFIG_MMC_WBSD is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+# CONFIG_TMPFS is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=y
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+CONFIG_NLS_CODEPAGE_850=y
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+CONFIG_NLS_ISO8859_15=y
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+CONFIG_NLS_UTF8=y
+# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_CRC_CCITT=y
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+# CONFIG_INSTRUMENTATION is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+CONFIG_BDI_SWITCH=y
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+# CONFIG_CRYPTO is not set
+# CONFIG_PPC_CLOCK is not set
*
^ permalink raw reply related
* Re: [PATCH 2/2] Base Warp Platform support
From: Sean MacLennan @ 2008-01-08 19:01 UTC (permalink / raw)
To: benh; +Cc: linuxppc-dev
In-Reply-To: <1199517639.7291.45.camel@pasglop>
--- /dev/null 2005-11-20 22:22:37.000000000 -0500
+++ arch/powerpc/boot/cuboot-warp.c 2008-01-08 12:09:39.000000000 -0500
@@ -0,0 +1,25 @@
+/*
+ * Copyright (c) 2008 PIKA Technologies
+ * Sean MacLennan <smaclennan@pikatech.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "44x.h"
+#include "cuboot.h"
+
+#define TARGET_44x
+#include "ppcboot.h"
+
+static bd_t bd;
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+ unsigned long r6, unsigned long r7)
+{
+ CUBOOT_INIT();
+
+ warp_init(&bd.bi_enetaddr, &bd.bi_enet1addr);
+}
--- /dev/null 2005-11-20 22:22:37.000000000 -0500
+++ arch/powerpc/boot/dts/warp.dts 2008-01-08 12:04:10.000000000 -0500
@@ -0,0 +1,232 @@
+/*
+ * Device Tree Source for PIKA Warp
+ *
+ * Copyright (c) 2008 PIKA Technologies
+ * Sean MacLennan <smaclennan@pikatech.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ model = "pika,warp";
+ compatible = "pika,warp";
+ dcr-parent = <&/cpus/cpu@0>;
+
+ aliases {
+ ethernet0 = &EMAC0;
+ serial0 = &UART0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ model = "PowerPC,440EP";
+ reg = <0>;
+ clock-frequency = <0>; /* Filled in by zImage */
+ timebase-frequency = <0>; /* Filled in by zImage */
+ i-cache-line-size = <20>;
+ d-cache-line-size = <20>;
+ i-cache-size = <8000>;
+ d-cache-size = <8000>;
+ dcr-controller;
+ dcr-access-method = "native";
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0 0>; /* Filled in by zImage */
+ };
+
+ UIC0: interrupt-controller0 {
+ compatible = "ibm,uic-440ep","ibm,uic";
+ interrupt-controller;
+ cell-index = <0>;
+ dcr-reg = <0c0 009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ };
+
+ UIC1: interrupt-controller1 {
+ compatible = "ibm,uic-440ep","ibm,uic";
+ interrupt-controller;
+ cell-index = <1>;
+ dcr-reg = <0d0 009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupts = <1e 4 1f 4>; /* cascade */
+ interrupt-parent = <&UIC0>;
+ };
+
+ SDR0: sdr {
+ compatible = "ibm,sdr-440ep";
+ dcr-reg = <00e 002>;
+ };
+
+ CPR0: cpr {
+ compatible = "ibm,cpr-440ep";
+ dcr-reg = <00c 002>;
+ };
+
+ plb {
+ compatible = "ibm,plb-440ep", "ibm,plb-440gp", "ibm,plb4";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges;
+ clock-frequency = <0>; /* Filled in by zImage */
+
+ SDRAM0: sdram {
+ compatible = "ibm,sdram-440ep", "ibm,sdram-405gp";
+ dcr-reg = <010 2>;
+ };
+
+ DMA0: dma {
+ compatible = "ibm,dma-440ep", "ibm,dma-440gp";
+ dcr-reg = <100 027>;
+ };
+
+ FPGA0: fpga {
+ compatible = "pika,fpga";
+ reg = <0 80000000 2200>;
+ interrupts = <18 8>;
+ interrupt-parent = <&UIC0>;
+ };
+
+ MAL0: mcmal {
+ compatible = "ibm,mcmal-440ep", "ibm,mcmal-440gp", "ibm,mcmal";
+ dcr-reg = <180 62>;
+ num-tx-chans = <4>;
+ num-rx-chans = <2>;
+ interrupt-parent = <&MAL0>;
+ interrupts = <0 1 2 3 4>;
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-map = </*TXEOB*/ 0 &UIC0 a 4
+ /*RXEOB*/ 1 &UIC0 b 4
+ /*SERR*/ 2 &UIC1 0 4
+ /*TXDE*/ 3 &UIC1 1 4
+ /*RXDE*/ 4 &UIC1 2 4>;
+ };
+
+ POB0: opb {
+ compatible = "ibm,opb-440ep", "ibm,opb-440gp", "ibm,opb";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <00000000 0 00000000 80000000
+ 80000000 0 80000000 80000000>;
+ interrupt-parent = <&UIC1>;
+ interrupts = <7 4>;
+ clock-frequency = <0>; /* Filled in by zImage */
+
+ EBC0: ebc {
+ compatible = "ibm,ebc-440ep", "ibm,ebc-440gp", "ibm,ebc";
+ dcr-reg = <012 2>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ clock-frequency = <0>; /* Filled in by zImage */
+ interrupts = <5 1>;
+ interrupt-parent = <&UIC1>;
+
+ nor_flash@0,0 {
+ /* Really spansion */
+ compatible = "amd,s29gl512n", "cfi-flash";
+ bank-width = <2>;
+ reg = <0 ffc00000 4000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition@0 {
+ label = "kernel";
+ reg = <0 180000>;
+ };
+ partition@180000 {
+ label = "root";
+ reg = <180000 3480000>;
+ };
+ partition@3600000 {
+ label = "user";
+ reg = <3600000 900000>;
+ };
+ partition@3f00000 {
+ label = "fpga";
+ reg = <3f00000 40000>;
+ };
+ partition@3f40000 {
+ label = "env";
+ reg = <3f40000 40000>;
+ };
+ partition@3f80000 {
+ label = "u-boot";
+ reg = <3f80000 80000>;
+ };
+ };
+ };
+
+ UART0: serial@ef600300 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <ef600300 8>;
+ virtual-reg = <ef600300>;
+ clock-frequency = <0>; /* Filled in by zImage */
+ current-speed = <1c200>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <0 4>;
+ };
+
+ IIC0: i2c@ef600700 {
+ device_type = "i2c";
+ compatible = "ibm,iic-440ep", "ibm,iic-440gp", "ibm,iic";
+ reg = <ef600700 14>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <2 4>;
+ };
+
+ ZMII0: emac-zmii@ef600d00 {
+ device_type = "zmii-interface";
+ compatible = "ibm,zmii-440ep", "ibm,zmii-440gp", "ibm,zmii";
+ reg = <ef600d00 c>;
+ };
+
+ EMAC0: ethernet@ef600e00 {
+ linux,network-index = <0>;
+ device_type = "network";
+ compatible = "ibm,emac-440ep", "ibm,emac-440gp", "ibm,emac";
+ interrupt-parent = <&UIC1>;
+ interrupts = <1c 4 1d 4>;
+ reg = <ef600e00 70>;
+ local-mac-address = [000000000000];
+ mal-device = <&MAL0>;
+ mal-tx-channel = <0 1>;
+ mal-rx-channel = <0>;
+ cell-index = <0>;
+ max-frame-size = <5dc>;
+ rx-fifo-size = <1000>;
+ tx-fifo-size = <800>;
+ phy-mode = "rmii";
+ phy-map = <00000000>;
+ zmii-device = <&ZMII0>;
+ zmii-channel = <0>;
+ };
+
+ usb@ef601000 {
+ compatible = "ohci-be";
+ reg = <ef601000 80>;
+ interrupts = <8 1 9 1>;
+ interrupt-parent = < &UIC1 >;
+ };
+ };
+ };
+
+ chosen {
+ linux,stdout-path = "/plb/opb/serial@ef600300";
+ };
+};
--- /dev/null 2005-11-20 22:22:37.000000000 -0500
+++ arch/powerpc/boot/warp.c 2008-01-08 12:09:54.000000000 -0500
@@ -0,0 +1,33 @@
+/*
+ * Copyright (c) 2008 PIKA Technologies
+ * Sean MacLennan <smaclennan@pikatech.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; version 2 of the License
+ */
+#include "ops.h"
+#include "4xx.h"
+#include "44x.h"
+
+static u8 *warp_mac0, *warp_mac1;
+
+static void warp_fixups(void)
+{
+ unsigned long sysclk = 66000000;
+
+ ibm440ep_fixup_clocks(sysclk, 11059200, 50000000);
+ ibm4xx_sdram_fixup_memsize();
+ ibm4xx_quiesce_eth((u32 *)0xef600e00, (u32 *)0xef600f00);
+ dt_fixup_mac_addresses(warp_mac0, warp_mac1);
+}
+
+void warp_init(void *mac0, void *mac1)
+{
+ platform_ops.fixups = warp_fixups;
+ platform_ops.exit = ibm44x_dbcr_reset;
+ warp_mac0 = mac0;
+ warp_mac1 = mac1;
+ fdt_init(_dtb_start);
+ serial_console_init();
+}
^ permalink raw reply
* Re: [PATCH] Hwmon for Taco
From: Josh Boyer @ 2008-01-08 19:02 UTC (permalink / raw)
To: Sean MacLennan; +Cc: linuxppc-dev
In-Reply-To: <4783C128.8050103@pikatech.com>
On Tue, 08 Jan 2008 13:30:00 -0500
Sean MacLennan <smaclennan@pikatech.com> wrote:
> Ok, here is the ad7414 only. taco-dtm is no more!
Cool. Couple more things.
1) This should go through the hwmon maintainer. Send it to him.
(CC'ing this list is of course fine.)
2) You always need the Signed-off-by: for each patch you send
3) If you didn't author the code (this seems to come from Stefan), then
you need the Signed-off-by from the original author.
You're getting there :) These are all "newbie" type mistakes so keep
plugging away.
josh
^ permalink raw reply
* Re: [PATCH 4/7] Device tree for MPC5121 ADS
From: Scott Wood @ 2008-01-08 19:22 UTC (permalink / raw)
To: John Rigby; +Cc: linuxppc-dev
In-Reply-To: <1199808093-15929-5-git-send-email-jrigby@freescale.com>
On Tue, Jan 08, 2008 at 09:01:30AM -0700, John Rigby wrote:
> + cpld@82000000 {
> + device_type = "board-control";
> + reg = <82000000 8000>;
> + };
Should be:
baord-control@82000000 {
compatible = "fsl,mpc5121ads-cpld";
reg = <82000000 8000>;
};
> + ref-frequency = <3ef1480>; // 66MHz ref
> + bus-frequency = <5e69ec0>; // 99MHz ips ref
Please specify these in decimal rather than hex (using the d# prefix, or
better yet /dts-v1/).
> + // IPIC
> + // interrupts cell = <intr #, sense>
> + // sense values match linux IORESOURCE_IRQ_* defines:
> + // sense == 8: Level, low assertion
> + // sense == 2: Edge, high-to-low change
> + //
> + ipic: pic@c00 {
> + interrupt-controller;
> + #address-cells = <0>;
> + #interrupt-cells = <2>;
> + reg = <c00 100>;
> + built-in;
> + device_type = "ipic";
> + };
Remove built-in.
-Scott
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox