Re: [PATCH] early serial init

[John Tyner <jtyner@cs.ucr.edu>]

I remember seeing something awhile ago about early boots, but I didn't
think it was for Walnut. Where is it/would it be?

On Thu, 11 Apr 2002, Armin wrote:

> John Tyner wrote:
> > Here is a patch to setup the serial ports early. It works fine on our
> > walnut boards.
> >
> > --- arch/ppc/platforms/walnut.c.orig	Thu Apr 11 12:55:55 2002
> > +++ arch/ppc/platforms/walnut.c	Thu Apr 11 12:58:35 2002
> > @@ -31,6 +31,7 @@
> >  #include <linux/blk.h>
> >  #include <linux/pci.h>
> >  #include <linux/rtc.h>
> > +#include <linux/serial.h>
> >
> >  #include <asm/system.h>
> >  #include <asm/pci-bridge.h>
> > @@ -247,6 +248,11 @@
> >  void __init
> >  board_init(void)
> >  {
> > +	struct serial_struct serial_req;
> > +	bd_t *bip = (bd_t *) __res;
> > +	u32 chrcr;
> > +	int div;
> > +	ulong bb;
> >  #ifdef CONFIG_PPC_RTC
> >  	ppc_md.time_init = todc_time_init;
> >  	ppc_md.set_rtc_time = todc_set_rtc_time;
> > @@ -254,4 +260,40 @@
> >  	ppc_md.nvram_read_val = todc_direct_read_val;
> >  	ppc_md.nvram_write_val = todc_direct_write_val;
> >  #endif
> > +	chrcr = mfdcr(DCRN_CHCR0);
> > +	div = ((chrcr&0x3e)>>1)+1;
> > +	div *= 16;
> > +	bb = bip->bi_intfreq/div;
> > +
> > +	if( !(chrcr & CHR0_U0EC) ){
> > +		memset(&serial_req, 0, sizeof(serial_req));
> > +		serial_req.line       = 0;
> > +		serial_req.baud_base  = bb;
> > +		serial_req.port       = 0;
> > +		serial_req.irq        = UART0_INT;
> > +		serial_req.flags      = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST;
> > +		serial_req.io_type    = SERIAL_IO_MEM;
> > +		serial_req.iomem_base = (u8 *)UART0_IO_BASE;
> > +		serial_req.iomem_reg_shift = 0;
> > +
> > +		if (early_serial_setup(&serial_req) != 0) {
> > +			printk("Early serial init of port 0 failed\n");
> > +		}
> > +	}
> > +
> > +	if( !(chrcr & CHR0_U1EC) ){
> > +		memset(&serial_req, 0, sizeof(serial_req));
> > +		serial_req.line       = 1;
> > +		serial_req.baud_base  = bb;
> > +		serial_req.port       = 1;
> > +		serial_req.irq        = UART1_INT;
> > +		serial_req.flags      = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST;
> > +		serial_req.io_type    = SERIAL_IO_MEM;
> > +		serial_req.iomem_base = (u8 *)UART1_IO_BASE;
> > +		serial_req.iomem_reg_shift = 0;
> > +
> > +		if (early_serial_setup(&serial_req) != 0) {
> > +			printk("Early serial init of port 1 failed\n");
> > +		}
> > +	}
> >  }
> >
> >
> >
> >
> >
>
> I thought we all ready had an early boot for walnut?
>
> armin
>


** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/