* MPC5200 PCI Issues
@ 2009-02-04 16:53 Tobias Knutsson
2009-02-04 17:54 ` Grant Likely
2009-02-06 13:34 ` Andre Schwarz
0 siblings, 2 replies; 9+ messages in thread
From: Tobias Knutsson @ 2009-02-04 16:53 UTC (permalink / raw)
To: linuxppc-dev
I am currently trying to get an MPC5200-based board to run Linux
2.6.28. Most of the devices are working, however i have some issues
with the PCI-bus. More precisely, the issue is that all of
the cards' IO-regions are mapped to address 0x0.
In my device tree I have the following:
pci@f0000d00 {
#interrupt-cells =3D <1>;
#size-cells =3D <2>;
#address-cells =3D <3>;
device_type =3D "pci";
compatible =3D "fsl,mpc5200b-pci","fsl,mpc5200-pci";
reg =3D <0xf0000d00 0x100>;
interrupt-map-mask =3D <0xf800 0 0 7>;
interrupt-map =3D <0xb000 0 0 1 &mpc5200_pic 0 0 3 // MPC520=
0
0xb000 0 0 2 &mpc5200_pic 0 0 3
0xb000 0 0 3 &mpc5200_pic 0 0 3
0xb000 0 0 4 &mpc5200_pic 0 0 3
0xb800 0 0 1 &mpc5200_pic 1 1 3 // c64x0
0xb800 0 0 2 &mpc5200_pic 1 1 3
0xb800 0 0 3 &mpc5200_pic 1 1 3
0xb800 0 0 4 &mpc5200_pic 1 1 3
0xc000 0 0 1 &mpc5200_pic 1 1 3 // c64x1
0xc000 0 0 2 &mpc5200_pic 1 1 3
0xc000 0 0 3 &mpc5200_pic 1 1 3
0xc000 0 0 4 &mpc5200_pic 1 1 3
0xc800 0 0 1 &mpc5200_pic 1 1 3 // c64x2
0xc800 0 0 2 &mpc5200_pic 1 1 3
0xc800 0 0 3 &mpc5200_pic 1 1 3
0xc800 0 0 4 &mpc5200_pic 1 1 3
0xd000 0 0 1 &mpc5200_pic 1 1 3 // c64x3
0xd000 0 0 2 &mpc5200_pic 1 1 3
0xd000 0 0 3 &mpc5200_pic 1 1 3
0xd000 0 0 4 &mpc5200_pic 1 1 3
0xd800 0 0 1 &mpc5200_pic 1 1 3 // c64x4
0xd800 0 0 2 &mpc5200_pic 1 1 3
0xd800 0 0 3 &mpc5200_pic 1 1 3
0xd800 0 0 4 &mpc5200_pic 1 1 3>;
clock-frequency =3D <0x1e84800>; //<0>; // From boot loader
interrupts =3D <2 8 0 2 9 0 2 10 0>;
interrupt-parent =3D <&mpc5200_pic>;
bus-range =3D <0 0>;
ranges =3D <0x02000000 0 0x50000000 0x50000000 0 0x10000000
0x01000000 0 0x00000000 0x60000000 0 0x01000000>;
};
The cards' memory regions are mapped out fine to different addresses
in the 0x50000000-0x60000000 range. However, the IO regions are all mapped
to zero.
Do you have any idea on what could be wrong or in which direction I
should be looking?
--=20
H=E4lsningar/Regards
Tobias Knutsson
^ permalink raw reply [flat|nested] 9+ messages in thread* Re: MPC5200 PCI Issues 2009-02-04 16:53 MPC5200 PCI Issues Tobias Knutsson @ 2009-02-04 17:54 ` Grant Likely 2009-02-05 7:06 ` Tobias Knutsson 2009-02-06 13:34 ` Andre Schwarz 1 sibling, 1 reply; 9+ messages in thread From: Grant Likely @ 2009-02-04 17:54 UTC (permalink / raw) To: Tobias Knutsson; +Cc: linuxppc-dev On Wed, Feb 4, 2009 at 9:53 AM, Tobias Knutsson <tobias.knutsson@gmail.com> wrote: > clock-frequency = <0x1e84800>; //<0>; // From boot loader > interrupts = <2 8 0 2 9 0 2 10 0>; > interrupt-parent = <&mpc5200_pic>; > bus-range = <0 0>; > ranges = <0x02000000 0 0x50000000 0x50000000 0 0x10000000 > 0x01000000 0 0x00000000 0x60000000 0 0x01000000>; > }; > > The cards' memory regions are mapped out fine to different addresses > in the 0x50000000-0x60000000 range. However, the IO regions are all mapped > to zero. > > Do you have any idea on what could be wrong or in which direction I > should be looking? Hmmm. Your ranges property looks okay to me. The MPC5200 setup code may be doing the wrong thing. Turn on debug at the top of arch/powerpc/platforms/mpc52xx/mpc52xx_pci.c and post your kernel output. g. -- Grant Likely, B.Sc., P.Eng. Secret Lab Technologies Ltd. ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: MPC5200 PCI Issues 2009-02-04 17:54 ` Grant Likely @ 2009-02-05 7:06 ` Tobias Knutsson 2009-02-05 16:44 ` Grant Likely 0 siblings, 1 reply; 9+ messages in thread From: Tobias Knutsson @ 2009-02-05 7:06 UTC (permalink / raw) To: Grant Likely; +Cc: linuxppc-dev When enabling the debug-printouts, it came to me that I forgot to mention something kind of important. Using the standard mpc52xx_pci.c, even the memory resources are mapped to zero. After disabling this code block, the memory regions are mapped out fine (but still no IO): static void mpc52xx_pci_fixup_resources(struct pci_dev *dev) { int i; pr_debug("mpc52xx_pci_fixup_resources() %.4x:%.4x\n", dev->vendor, dev->device); /* We don't rely on boot loader for PCI and resets all devices */ for (i =3D 0; i < DEVICE_COUNT_RESOURCE; i++) { struct resource *res =3D &dev->resource[i]; if (res->end > res->start) { /* Only valid resources */ res->end -=3D res->start; res->start =3D 0; res->flags |=3D IORESOURCE_UNSET; } } What is the purpose of this code? Since all resources are reset here, where are they inteded to be re-allocated? Here is the bootlog with the aforementioned code enabled: reading cuImage.lite5200b 1833699 bytes read ## Booting kernel from Legacy Image at 00201400 ... Image Name: Linux-2.6.28 Created: 2009-02-05 6:54:20 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1833635 Bytes =3D 1.7 MB Load Address: 00400000 Entry Point: 004005a0 Verifying Checksum ... OK Uncompressing Kernel Image ... OK [ 0.000000] Using lite5200 machine description [ 0.000000] Linux version 2.6.28 (tknutsson@ztn-ubuntu) (gcc version 4.3.2 (Sourcery G++ Lite 4.3-50) ) #66 Thu Feb 5 07:51:46 CET 2009 [ 0.000000] Adding MPC52xx PCI host bridge /pci@f0000d00 [ 0.000000] PCI host bridge /pci@f0000d00 (primary) ranges: [ 0.000000] MEM 0x0000000050000000..0x000000005fffffff -> 0x00000000500= 00000 [ 0.000000] IO 0x0000000060000000..0x0000000060ffffff -> 0x00000000000= 00000 [ 0.000000] mpc52xx_pci_setup(hose=3Dc03ec000, pci_regs=3Dfdffad00) [ 0.000000] mem_resource[0] =3D {.start=3D50000000, .end=3D5fffffff, .fl= ags=3D200} [ 0.000000] .io_resource=3D{.start=3D0,.end=3Dffffff,.flags=3D100} .io_base_phys=3D0x60000000 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000000 -> 0x00004000 [ 0.000000] Normal 0x00004000 -> 0x00004000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00004000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=3DttyPSC0,115200 root=3D/dev/sd= a2 rw [ 0.000000] MPC52xx PIC is up and running! [ 0.000000] PID hash table entries: 256 (order: 8, 1024 bytes) [ 0.000000] clocksource: timebase mult[7d00000] shift[22] registered [ 0.000263] console [ttyPSC0] enabled [ 0.121690] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes= ) [ 0.129012] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.147433] Memory: 60844k/65536k available (3704k kernel code, 4624k reserved, 156k data, 117k bss, 180k init) [ 0.157672] SLUB: Genslabs=3D12, HWalign=3D32, Order=3D0-3, MinObjects= =3D0, CPUs=3D1, Nodes=3D1 [ 0.165373] Calibrating delay loop... 63.87 BogoMIPS (lpj=3D127744) [ 0.236265] Mount-cache hash table entries: 512 [ 0.245719] net_namespace: 288 bytes [ 0.250237] NET: Registered protocol family 16 [ 0.284887] PCI: Probing PCI hardware [ 0.289670] mpc52xx_pci_fixup_resources() 1057:5809 [ 0.294799] PCI:0000:00:17.0 Resource 0 0000000050400000-00000000507fffff [21208] fixup... [ 0.303180] PCI:0000:00:17.0 0000000050400000-00000000507ffff= f [ 0.309998] PCI:0000:00:17.0 Resource 1 0000000050800000-0000000050ffffff [20200] fixup... [ 0.318262] PCI:0000:00:17.0 0000000050800000-0000000050fffff= f [ 0.325062] PCI:0000:00:17.0 Resource 2 0000000060000000-000000006000000f [20101] fixup... [ 0.333326] PCI:0000:00:17.0 0000000060000000-000000006000000= f [ 0.340124] mpc52xx_pci_fixup_resources() 104c:9065 [ 0.345242] PCI:0000:00:18.0 Resource 0 0000000051000000-00000000513fffff [21208] fixup... [ 0.353519] PCI:0000:00:18.0 0000000051000000-00000000513ffff= f [ 0.360319] PCI:0000:00:18.0 Resource 1 0000000051800000-0000000051ffffff [20200] fixup... [ 0.368583] PCI:0000:00:18.0 0000000051800000-0000000051fffff= f [ 0.375383] PCI:0000:00:18.0 Resource 2 0000000060000010-000000006000001f [20101] fixup... [ 0.383647] PCI:0000:00:18.0 0000000060000010-000000006000001= f [ 0.390444] mpc52xx_pci_fixup_resources() 104c:9065 [ 0.395549] PCI:0000:00:19.0 Resource 0 0000000052000000-00000000523fffff [21208] fixup... [ 0.403826] PCI:0000:00:19.0 0000000052000000-00000000523ffff= f [ 0.410626] PCI:0000:00:19.0 Resource 1 0000000052800000-0000000052ffffff [20200] fixup... [ 0.418889] PCI:0000:00:19.0 0000000052800000-0000000052fffff= f [ 0.425690] PCI:0000:00:19.0 Resource 2 0000000060000020-000000006000002f [20101] fixup... [ 0.433954] PCI:0000:00:19.0 0000000060000020-000000006000002= f [ 0.440751] mpc52xx_pci_fixup_resources() 104c:9065 [ 0.445854] PCI:0000:00:1a.0 Resource 0 0000000053000000-00000000533fffff [21208] fixup... [ 0.454130] PCI:0000:00:1a.0 0000000053000000-00000000533ffff= f [ 0.460930] PCI:0000:00:1a.0 Resource 1 0000000053800000-0000000053ffffff [20200] fixup... [ 0.469194] PCI:0000:00:1a.0 0000000053800000-0000000053fffff= f [ 0.475994] PCI:0000:00:1a.0 Resource 2 0000000060000030-000000006000003f [20101] fixup... [ 0.484258] PCI:0000:00:1a.0 0000000060000030-000000006000003= f [ 0.491056] mpc52xx_pci_fixup_resources() 104c:9065 [ 0.495999] PCI: Fixup bus 0 (PHB) [ 0.499383] PCI: device 0000:00:16.0 OF node: <none> [ 0.504371] PCI: device 0000:00:17.0 OF node: <none> [ 0.509363] PCI: device 0000:00:18.0 OF node: <none> [ 0.514354] PCI: device 0000:00:19.0 OF node: <none> [ 0.519345] PCI: device 0000:00:1a.0 OF node: <none> [ 0.524332] Try to map irq for 0000:00:16.0... [ 0.528808] Try to map irq for 0000:00:17.0... [ 0.533334] -> got one, spec 3 cells (0x00000001 0x00000001...) on /soc5200@f0000000/interrupt-controller@500 [ 0.543389] -> mapped to linux irq 65 [ 0.547117] Try to map irq for 0000:00:18.0... [ 0.551626] -> got one, spec 3 cells (0x00000001 0x00000001...) on /soc5200@f0000000/interrupt-controller@500 [ 0.561629] -> mapped to linux irq 65 [ 0.565353] Try to map irq for 0000:00:19.0... [ 0.569858] -> got one, spec 3 cells (0x00000001 0x00000001...) on /soc5200@f0000000/interrupt-controller@500 [ 0.579863] -> mapped to linux irq 65 [ 0.583587] Try to map irq for 0000:00:1a.0... [ 0.588099] -> got one, spec 3 cells (0x00000001 0x00000001...) on /soc5200@f0000000/interrupt-controller@500 [ 0.598103] -> mapped to linux irq 65 [ 0.605144] PCI: PHB (bus 0) bridge rsrc 0: 0000000000000000-0000000000ffffff [0x100], parent c03a1fdc (PCI IO) [ 0.615266] PCI: PHB (bus 0) bridge rsrc 1: 0000000050000000-000000005fffffff [0x200], parent c03a1fc0 (PCI mem) [ 0.625539] PCI: Assigning unassigned resouces... [ 0.630304] bus: 00 index 0 io port: [0x00-0xffffff] [ 0.635299] bus: 00 index 1 mmio: [0x50000000-0x5fffffff] [ 0.640909] DMA: MPC52xx BestComm driver [ 0.645214] DMA: MPC52xx BestComm engine @f0001200 ok ! [ 0.678739] SCSI subsystem initialized [ 0.709498] NET: Registered protocol family 2 [ 0.754980] IP route cache hash table entries: 1024 (order: 0, 4096 byte= s) [ 0.762429] TCP established hash table entries: 2048 (order: 2, 16384 by= tes) [ 0.769716] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.776224] TCP: Hash tables configured (established 2048 bind 2048) [ 0.782604] TCP reno registered [ 0.795054] NET: Registered protocol family 1 [ 0.846171] JFFS2 version 2.2. (NAND) (c) 2001-2006 Red Hat, Inc. [ 0.855699] msgmni has been set to 118 [ 0.861227] alg: No test for stdrng (krng) [ 0.865651] io scheduler noop registered [ 0.869658] io scheduler anticipatory registered (default) [ 0.875224] io scheduler deadline registered [ 0.879838] io scheduler cfq registered [ 1.442231] Generic RTC Driver v1.07 [ 1.447145] Serial: MPC52xx PSC UART driver [ 1.451885] f0002200.serial: ttyPSC2 at MMIO 0xf0002200 (irq =3D 130) is a MPC52xx PSC [ 1.461497] f0002400.serial: ttyPSC3 at MMIO 0xf0002400 (irq =3D 131) is a MPC52xx PSC [ 1.471257] f0002600.serial: ttyPSC4 at MMIO 0xf0002600 (irq =3D 139) is a MPC52xx PSC [ 1.480866] f0002800.serial: ttyPSC5 at MMIO 0xf0002800 (irq =3D 140) is a MPC52xx PSC [ 1.490461] f0002c00.serial: ttyPSC0 at MMIO 0xf0002c00 (irq =3D 132) is a MPC52xx PSC [ 1.521689] brd: module loaded [ 1.535886] loop: module loaded [ 1.544328] mpc52xx MII bus: probed [ 1.550220] net eth0: Using PHY at MDIO address 0 [ 1.556124] Driver 'sd' needs updating - please use bus_type methods [ 1.563224] ata: MPC52xx IDE/ATA libata driver [ 1.568729] scsi0 : mpc52xx_ata [ 1.573032] ata1: PATA max UDMA/33 ata_regs 0xf0003a00 irq 135 [ 1.751224] ata1.00: ATA-0: TRANSCEND, 20070831, max UDMA/66 [ 1.756948] ata1.00: 3915072 sectors, multi 0: LBA [ 1.775156] ata1.00: configured for UDMA/33 [ 1.803154] ata1.00: configured for UDMA/33 [ 1.807423] ata1: EH complete [ 1.811300] scsi 0:0:0:0: Direct-Access ATA TRANSCEND 2007 PQ: 0 ANSI: 5 [ 1.821337] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors: (2.00 GB/1.86 GiB) [ 1.829333] sd 0:0:0:0: [sda] Write Protect is off [ 1.834879] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1.844851] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors: (2.00 GB/1.86 GiB) [ 1.852841] sd 0:0:0:0: [sda] Write Protect is off [ 1.858259] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1.867450] sda: sda1 sda2 [ 1.881490] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.890711] fc000000.flash: Found 1 x16 devices at 0x0 in 8-bit bank [ 1.897222] Amd/Fujitsu Extended Query Table at 0x0040 [ 1.902529] fc000000.flash: CFI does not contain boot bank location. Assuming top. [ 1.910147] number of CFI chips: 1 [ 1.913603] cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. [ 1.922009] RedBoot partition parsing not available [ 1.926998] Creating 4 MTD partitions on "fc000000.flash": [ 1.932547] 0x00000000-0x00500000 : "u-boot" [ 1.940601] 0x00500000-0x01000000 : "kernel" [ 1.948071] 0x01000000-0x02000000 : "rootfs" [ 1.955601] 0x02000000-0x03000000 : "application" [ 1.964240] i2c /dev entries driver [ 1.975775] Advanced Linux Sound Architecture Driver Version 1.0.18rc3. [ 1.983814] ASoC version 0.13.2 [ 1.987668] tlv320aic23 0-001a: probing tlv320aic23 i2c device [ 2.040451] registering ASoC codec driver: /soc5200@f0000000/i2c@3d00/codec@1a [ 2.049539] ALSA device list: [ 2.052591] No soundcards found. [ 2.057430] TCP cubic registered [ 2.060765] NET: Registered protocol family 17 [ 2.066886] RPC: Registered udp transport module. [ 2.071683] RPC: Registered tcp transport module. [ 2.087086] EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended [ 2.094828] VFS: Mounted root (ext2 filesystem). [ 2.099690] Freeing unused kernel memory: 180k init On Wed, Feb 4, 2009 at 18:54, Grant Likely <grant.likely@secretlab.ca> wrot= e: > On Wed, Feb 4, 2009 at 9:53 AM, Tobias Knutsson > <tobias.knutsson@gmail.com> wrote: >> clock-frequency =3D <0x1e84800>; //<0>; // From boot load= er >> interrupts =3D <2 8 0 2 9 0 2 10 0>; >> interrupt-parent =3D <&mpc5200_pic>; >> bus-range =3D <0 0>; >> ranges =3D <0x02000000 0 0x50000000 0x50000000 0 0x1000000= 0 >> 0x01000000 0 0x00000000 0x60000000 0 0x01000000>= ; >> }; >> >> The cards' memory regions are mapped out fine to different addresses >> in the 0x50000000-0x60000000 range. However, the IO regions are all mapp= ed >> to zero. >> >> Do you have any idea on what could be wrong or in which direction I >> should be looking? > > Hmmm. Your ranges property looks okay to me. The MPC5200 setup code > may be doing the wrong thing. Turn on debug at the top of > arch/powerpc/platforms/mpc52xx/mpc52xx_pci.c and post your kernel > output. > > g. > > -- > Grant Likely, B.Sc., P.Eng. > Secret Lab Technologies Ltd. > --=20 H=E4lsningar/Regards Tobias Knutsson ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: MPC5200 PCI Issues 2009-02-05 7:06 ` Tobias Knutsson @ 2009-02-05 16:44 ` Grant Likely 2009-02-05 20:03 ` Tobias Knutsson 0 siblings, 1 reply; 9+ messages in thread From: Grant Likely @ 2009-02-05 16:44 UTC (permalink / raw) To: Tobias Knutsson; +Cc: linuxppc-dev On Thu, Feb 5, 2009 at 12:06 AM, Tobias Knutsson <tobias.knutsson@gmail.com> wrote: > When enabling the debug-printouts, it came to me that I forgot to > mention something kind of important. Using the standard mpc52xx_pci.c, > even the memory resources are mapped to zero. > > After disabling this code block, the memory regions are mapped out > fine (but still no IO): Reenable this code, enable debug in arch/powerpc/kernel/pci-common.c, and post the results. When this code is disabled then you're just getting the leftovers from U-Boot's scan of the PCI bus. For MPC5200 support Linux does its own scan and its own allocation of memory/IO address space and this code is needed to make sure that happens. g. > > static void > mpc52xx_pci_fixup_resources(struct pci_dev *dev) > { > int i; > > pr_debug("mpc52xx_pci_fixup_resources() %.4x:%.4x\n", > dev->vendor, dev->device); > > /* We don't rely on boot loader for PCI and resets all > devices */ > for (i =3D 0; i < DEVICE_COUNT_RESOURCE; i++) { > struct resource *res =3D &dev->resource[i]; > if (res->end > res->start) { /* Only valid resources */ > res->end -=3D res->start; > res->start =3D 0; > res->flags |=3D IORESOURCE_UNSET; > } > } > > What is the purpose of this code? Since all resources are reset here, > where are they inteded to be re-allocated? > > Here is the bootlog with the aforementioned code enabled: > > > reading cuImage.lite5200b > > 1833699 bytes read > ## Booting kernel from Legacy Image at 00201400 ... > Image Name: Linux-2.6.28 > Created: 2009-02-05 6:54:20 UTC > Image Type: PowerPC Linux Kernel Image (gzip compressed) > Data Size: 1833635 Bytes =3D 1.7 MB > Load Address: 00400000 > Entry Point: 004005a0 > Verifying Checksum ... OK > Uncompressing Kernel Image ... OK > [ 0.000000] Using lite5200 machine description > [ 0.000000] Linux version 2.6.28 (tknutsson@ztn-ubuntu) (gcc > version 4.3.2 (Sourcery G++ Lite 4.3-50) ) #66 Thu Feb 5 07:51:46 CET > 2009 > [ 0.000000] Adding MPC52xx PCI host bridge /pci@f0000d00 > [ 0.000000] PCI host bridge /pci@f0000d00 (primary) ranges: > [ 0.000000] MEM 0x0000000050000000..0x000000005fffffff -> 0x000000005= 0000000 > [ 0.000000] IO 0x0000000060000000..0x0000000060ffffff -> 0x000000000= 0000000 > [ 0.000000] mpc52xx_pci_setup(hose=3Dc03ec000, pci_regs=3Dfdffad00) > [ 0.000000] mem_resource[0] =3D {.start=3D50000000, .end=3D5fffffff, .= flags=3D200} > [ 0.000000] .io_resource=3D{.start=3D0,.end=3Dffffff,.flags=3D100} > .io_base_phys=3D0x60000000 > [ 0.000000] Zone PFN ranges: > [ 0.000000] DMA 0x00000000 -> 0x00004000 > [ 0.000000] Normal 0x00004000 -> 0x00004000 > [ 0.000000] Movable zone start PFN for each node > [ 0.000000] early_node_map[1] active PFN ranges > [ 0.000000] 0: 0x00000000 -> 0x00004000 > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. > Total pages: 16256 > [ 0.000000] Kernel command line: console=3DttyPSC0,115200 root=3D/dev/= sda2 rw > [ 0.000000] MPC52xx PIC is up and running! > [ 0.000000] PID hash table entries: 256 (order: 8, 1024 bytes) > [ 0.000000] clocksource: timebase mult[7d00000] shift[22] registered > [ 0.000263] console [ttyPSC0] enabled > [ 0.121690] Dentry cache hash table entries: 8192 (order: 3, 32768 byt= es) > [ 0.129012] Inode-cache hash table entries: 4096 (order: 2, 16384 byte= s) > [ 0.147433] Memory: 60844k/65536k available (3704k kernel code, > 4624k reserved, 156k data, 117k bss, 180k init) > [ 0.157672] SLUB: Genslabs=3D12, HWalign=3D32, Order=3D0-3, MinObjects= =3D0, > CPUs=3D1, Nodes=3D1 > [ 0.165373] Calibrating delay loop... 63.87 BogoMIPS (lpj=3D127744) > [ 0.236265] Mount-cache hash table entries: 512 > [ 0.245719] net_namespace: 288 bytes > [ 0.250237] NET: Registered protocol family 16 > [ 0.284887] PCI: Probing PCI hardware > [ 0.289670] mpc52xx_pci_fixup_resources() 1057:5809 > [ 0.294799] PCI:0000:00:17.0 Resource 0 > 0000000050400000-00000000507fffff [21208] fixup... > [ 0.303180] PCI:0000:00:17.0 0000000050400000-00000000507ff= fff > [ 0.309998] PCI:0000:00:17.0 Resource 1 > 0000000050800000-0000000050ffffff [20200] fixup... > [ 0.318262] PCI:0000:00:17.0 0000000050800000-0000000050fff= fff > [ 0.325062] PCI:0000:00:17.0 Resource 2 > 0000000060000000-000000006000000f [20101] fixup... > [ 0.333326] PCI:0000:00:17.0 0000000060000000-0000000060000= 00f > [ 0.340124] mpc52xx_pci_fixup_resources() 104c:9065 > [ 0.345242] PCI:0000:00:18.0 Resource 0 > 0000000051000000-00000000513fffff [21208] fixup... > [ 0.353519] PCI:0000:00:18.0 0000000051000000-00000000513ff= fff > [ 0.360319] PCI:0000:00:18.0 Resource 1 > 0000000051800000-0000000051ffffff [20200] fixup... > [ 0.368583] PCI:0000:00:18.0 0000000051800000-0000000051fff= fff > [ 0.375383] PCI:0000:00:18.0 Resource 2 > 0000000060000010-000000006000001f [20101] fixup... > [ 0.383647] PCI:0000:00:18.0 0000000060000010-0000000060000= 01f > [ 0.390444] mpc52xx_pci_fixup_resources() 104c:9065 > [ 0.395549] PCI:0000:00:19.0 Resource 0 > 0000000052000000-00000000523fffff [21208] fixup... > [ 0.403826] PCI:0000:00:19.0 0000000052000000-00000000523ff= fff > [ 0.410626] PCI:0000:00:19.0 Resource 1 > 0000000052800000-0000000052ffffff [20200] fixup... > [ 0.418889] PCI:0000:00:19.0 0000000052800000-0000000052fff= fff > [ 0.425690] PCI:0000:00:19.0 Resource 2 > 0000000060000020-000000006000002f [20101] fixup... > [ 0.433954] PCI:0000:00:19.0 0000000060000020-0000000060000= 02f > [ 0.440751] mpc52xx_pci_fixup_resources() 104c:9065 > [ 0.445854] PCI:0000:00:1a.0 Resource 0 > 0000000053000000-00000000533fffff [21208] fixup... > [ 0.454130] PCI:0000:00:1a.0 0000000053000000-00000000533ff= fff > [ 0.460930] PCI:0000:00:1a.0 Resource 1 > 0000000053800000-0000000053ffffff [20200] fixup... > [ 0.469194] PCI:0000:00:1a.0 0000000053800000-0000000053fff= fff > [ 0.475994] PCI:0000:00:1a.0 Resource 2 > 0000000060000030-000000006000003f [20101] fixup... > [ 0.484258] PCI:0000:00:1a.0 0000000060000030-0000000060000= 03f > [ 0.491056] mpc52xx_pci_fixup_resources() 104c:9065 > [ 0.495999] PCI: Fixup bus 0 (PHB) > [ 0.499383] PCI: device 0000:00:16.0 OF node: <none> > [ 0.504371] PCI: device 0000:00:17.0 OF node: <none> > [ 0.509363] PCI: device 0000:00:18.0 OF node: <none> > [ 0.514354] PCI: device 0000:00:19.0 OF node: <none> > [ 0.519345] PCI: device 0000:00:1a.0 OF node: <none> > [ 0.524332] Try to map irq for 0000:00:16.0... > [ 0.528808] Try to map irq for 0000:00:17.0... > [ 0.533334] -> got one, spec 3 cells (0x00000001 0x00000001...) on > /soc5200@f0000000/interrupt-controller@500 > [ 0.543389] -> mapped to linux irq 65 > [ 0.547117] Try to map irq for 0000:00:18.0... > [ 0.551626] -> got one, spec 3 cells (0x00000001 0x00000001...) on > /soc5200@f0000000/interrupt-controller@500 > [ 0.561629] -> mapped to linux irq 65 > [ 0.565353] Try to map irq for 0000:00:19.0... > [ 0.569858] -> got one, spec 3 cells (0x00000001 0x00000001...) on > /soc5200@f0000000/interrupt-controller@500 > [ 0.579863] -> mapped to linux irq 65 > [ 0.583587] Try to map irq for 0000:00:1a.0... > [ 0.588099] -> got one, spec 3 cells (0x00000001 0x00000001...) on > /soc5200@f0000000/interrupt-controller@500 > [ 0.598103] -> mapped to linux irq 65 > [ 0.605144] PCI: PHB (bus 0) bridge rsrc 0: > 0000000000000000-0000000000ffffff [0x100], parent c03a1fdc (PCI IO) > [ 0.615266] PCI: PHB (bus 0) bridge rsrc 1: > 0000000050000000-000000005fffffff [0x200], parent c03a1fc0 (PCI mem) > [ 0.625539] PCI: Assigning unassigned resouces... > [ 0.630304] bus: 00 index 0 io port: [0x00-0xffffff] > [ 0.635299] bus: 00 index 1 mmio: [0x50000000-0x5fffffff] > [ 0.640909] DMA: MPC52xx BestComm driver > [ 0.645214] DMA: MPC52xx BestComm engine @f0001200 ok ! > [ 0.678739] SCSI subsystem initialized > [ 0.709498] NET: Registered protocol family 2 > [ 0.754980] IP route cache hash table entries: 1024 (order: 0, 4096 by= tes) > [ 0.762429] TCP established hash table entries: 2048 (order: 2, 16384 = bytes) > [ 0.769716] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) > [ 0.776224] TCP: Hash tables configured (established 2048 bind 2048) > [ 0.782604] TCP reno registered > [ 0.795054] NET: Registered protocol family 1 > [ 0.846171] JFFS2 version 2.2. (NAND) (c) 2001-2006 Red Hat, Inc. > [ 0.855699] msgmni has been set to 118 > [ 0.861227] alg: No test for stdrng (krng) > [ 0.865651] io scheduler noop registered > [ 0.869658] io scheduler anticipatory registered (default) > [ 0.875224] io scheduler deadline registered > [ 0.879838] io scheduler cfq registered > [ 1.442231] Generic RTC Driver v1.07 > [ 1.447145] Serial: MPC52xx PSC UART driver > [ 1.451885] f0002200.serial: ttyPSC2 at MMIO 0xf0002200 (irq =3D 130) > is a MPC52xx PSC > [ 1.461497] f0002400.serial: ttyPSC3 at MMIO 0xf0002400 (irq =3D 131) > is a MPC52xx PSC > [ 1.471257] f0002600.serial: ttyPSC4 at MMIO 0xf0002600 (irq =3D 139) > is a MPC52xx PSC > [ 1.480866] f0002800.serial: ttyPSC5 at MMIO 0xf0002800 (irq =3D 140) > is a MPC52xx PSC > [ 1.490461] f0002c00.serial: ttyPSC0 at MMIO 0xf0002c00 (irq =3D 132) > is a MPC52xx PSC > [ 1.521689] brd: module loaded > [ 1.535886] loop: module loaded > [ 1.544328] mpc52xx MII bus: probed > [ 1.550220] net eth0: Using PHY at MDIO address 0 > [ 1.556124] Driver 'sd' needs updating - please use bus_type methods > [ 1.563224] ata: MPC52xx IDE/ATA libata driver > [ 1.568729] scsi0 : mpc52xx_ata > [ 1.573032] ata1: PATA max UDMA/33 ata_regs 0xf0003a00 irq 135 > [ 1.751224] ata1.00: ATA-0: TRANSCEND, 20070831, max UDMA/66 > [ 1.756948] ata1.00: 3915072 sectors, multi 0: LBA > [ 1.775156] ata1.00: configured for UDMA/33 > [ 1.803154] ata1.00: configured for UDMA/33 > [ 1.807423] ata1: EH complete > [ 1.811300] scsi 0:0:0:0: Direct-Access ATA TRANSCEND > 2007 PQ: 0 ANSI: 5 > [ 1.821337] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors: > (2.00 GB/1.86 GiB) > [ 1.829333] sd 0:0:0:0: [sda] Write Protect is off > [ 1.834879] sd 0:0:0:0: [sda] Write cache: disabled, read cache: > enabled, doesn't support DPO or FUA > [ 1.844851] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors: > (2.00 GB/1.86 GiB) > [ 1.852841] sd 0:0:0:0: [sda] Write Protect is off > [ 1.858259] sd 0:0:0:0: [sda] Write cache: disabled, read cache: > enabled, doesn't support DPO or FUA > [ 1.867450] sda: sda1 sda2 > [ 1.881490] sd 0:0:0:0: [sda] Attached SCSI disk > [ 1.890711] fc000000.flash: Found 1 x16 devices at 0x0 in 8-bit bank > [ 1.897222] Amd/Fujitsu Extended Query Table at 0x0040 > [ 1.902529] fc000000.flash: CFI does not contain boot bank > location. Assuming top. > [ 1.910147] number of CFI chips: 1 > [ 1.913603] cfi_cmdset_0002: Disabling erase-suspend-program due to > code brokenness. > [ 1.922009] RedBoot partition parsing not available > [ 1.926998] Creating 4 MTD partitions on "fc000000.flash": > [ 1.932547] 0x00000000-0x00500000 : "u-boot" > [ 1.940601] 0x00500000-0x01000000 : "kernel" > [ 1.948071] 0x01000000-0x02000000 : "rootfs" > [ 1.955601] 0x02000000-0x03000000 : "application" > [ 1.964240] i2c /dev entries driver > [ 1.975775] Advanced Linux Sound Architecture Driver Version 1.0.18rc3= . > [ 1.983814] ASoC version 0.13.2 > [ 1.987668] tlv320aic23 0-001a: probing tlv320aic23 i2c device > [ 2.040451] registering ASoC codec driver: > /soc5200@f0000000/i2c@3d00/codec@1a > [ 2.049539] ALSA device list: > [ 2.052591] No soundcards found. > [ 2.057430] TCP cubic registered > [ 2.060765] NET: Registered protocol family 17 > [ 2.066886] RPC: Registered udp transport module. > [ 2.071683] RPC: Registered tcp transport module. > [ 2.087086] EXT2-fs warning: mounting unchecked fs, running e2fsck > is recommended > [ 2.094828] VFS: Mounted root (ext2 filesystem). > [ 2.099690] Freeing unused kernel memory: 180k init > > On Wed, Feb 4, 2009 at 18:54, Grant Likely <grant.likely@secretlab.ca> wr= ote: >> On Wed, Feb 4, 2009 at 9:53 AM, Tobias Knutsson >> <tobias.knutsson@gmail.com> wrote: >>> clock-frequency =3D <0x1e84800>; //<0>; // From boot loa= der >>> interrupts =3D <2 8 0 2 9 0 2 10 0>; >>> interrupt-parent =3D <&mpc5200_pic>; >>> bus-range =3D <0 0>; >>> ranges =3D <0x02000000 0 0x50000000 0x50000000 0 0x100000= 00 >>> 0x01000000 0 0x00000000 0x60000000 0 0x01000000= >; >>> }; >>> >>> The cards' memory regions are mapped out fine to different addresses >>> in the 0x50000000-0x60000000 range. However, the IO regions are all map= ped >>> to zero. >>> >>> Do you have any idea on what could be wrong or in which direction I >>> should be looking? >> >> Hmmm. Your ranges property looks okay to me. The MPC5200 setup code >> may be doing the wrong thing. Turn on debug at the top of >> arch/powerpc/platforms/mpc52xx/mpc52xx_pci.c and post your kernel >> output. >> >> g. >> >> -- >> Grant Likely, B.Sc., P.Eng. >> Secret Lab Technologies Ltd. >> > > > > -- > > H=E4lsningar/Regards > Tobias Knutsson > --=20 Grant Likely, B.Sc., P.Eng. Secret Lab Technologies Ltd. ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: MPC5200 PCI Issues 2009-02-05 16:44 ` Grant Likely @ 2009-02-05 20:03 ` Tobias Knutsson 2009-02-06 11:46 ` Tobias Knutsson 0 siblings, 1 reply; 9+ messages in thread From: Tobias Knutsson @ 2009-02-05 20:03 UTC (permalink / raw) To: Grant Likely; +Cc: linuxppc-dev@ozlabs.org Hi, That is exactly what the bootlog shows. Debug output on in both =20 mpc52xx_pci.c and in pci-common.c. And the discussed code section =20 enabled. H=C3=A4lsningar / Regards Tobias Knutsson On 5 feb 2009, at 17.44, Grant Likely <grant.likely@secretlab.ca> wrote: > On Thu, Feb 5, 2009 at 12:06 AM, Tobias Knutsson > <tobias.knutsson@gmail.com> wrote: >> When enabling the debug-printouts, it came to me that I forgot to >> mention something kind of important. Using the standard =20 >> mpc52xx_pci.c, >> even the memory resources are mapped to zero. >> >> After disabling this code block, the memory regions are mapped out >> fine (but still no IO): > > Reenable this code, enable debug in arch/powerpc/kernel/pci-common.c, > and post the results. > > When this code is disabled then you're just getting the leftovers from > U-Boot's scan of the PCI bus. For MPC5200 support Linux does its own > scan and its own allocation of memory/IO address space and this code > is needed to make sure that happens. > > g. > >> >> static void >> mpc52xx_pci_fixup_resources(struct pci_dev *dev) >> { >> int i; >> >> pr_debug("mpc52xx_pci_fixup_resources() %.4x:%.4x\n", >> dev->vendor, dev->device); >> >> /* We don't rely on boot loader for PCI and resets all >> devices */ >> for (i =3D 0; i < DEVICE_COUNT_RESOURCE; i++) { >> struct resource *res =3D &dev->resource[i]; >> if (res->end > res->start) { /* Only valid =20 >> resources */ >> res->end -=3D res->start; >> res->start =3D 0; >> res->flags |=3D IORESOURCE_UNSET; >> } >> } >> >> What is the purpose of this code? Since all resources are reset here, >> where are they inteded to be re-allocated? >> >> Here is the bootlog with the aforementioned code enabled: >> >> >> reading cuImage.lite5200b >> >> 1833699 bytes read >> ## Booting kernel from Legacy Image at 00201400 ... >> Image Name: Linux-2.6.28 >> Created: 2009-02-05 6:54:20 UTC >> Image Type: PowerPC Linux Kernel Image (gzip compressed) >> Data Size: 1833635 Bytes =3D 1.7 MB >> Load Address: 00400000 >> Entry Point: 004005a0 >> Verifying Checksum ... OK >> Uncompressing Kernel Image ... OK >> [ 0.000000] Using lite5200 machine description >> [ 0.000000] Linux version 2.6.28 (tknutsson@ztn-ubuntu) (gcc >> version 4.3.2 (Sourcery G++ Lite 4.3-50) ) #66 Thu Feb 5 07:51:46 CET >> 2009 >> [ 0.000000] Adding MPC52xx PCI host bridge /pci@f0000d00 >> [ 0.000000] PCI host bridge /pci@f0000d00 (primary) ranges: >> [ 0.000000] MEM 0x0000000050000000..0x000000005fffffff -> =20 >> 0x0000000050000000 >> [ 0.000000] IO 0x0000000060000000..0x0000000060ffffff -> =20 >> 0x0000000000000000 >> [ 0.000000] mpc52xx_pci_setup(hose=3Dc03ec000, pci_regs=3Dfdffad00) >> [ 0.000000] mem_resource[0] =3D =20 >> {.start=3D50000000, .end=3D5fffffff, .flags=3D200} >> [ 0.000000] .io_resource=3D{.start=3D0,.end=3Dffffff,.flags=3D100} >> .io_base_phys=3D0x60000000 >> [ 0.000000] Zone PFN ranges: >> [ 0.000000] DMA 0x00000000 -> 0x00004000 >> [ 0.000000] Normal 0x00004000 -> 0x00004000 >> [ 0.000000] Movable zone start PFN for each node >> [ 0.000000] early_node_map[1] active PFN ranges >> [ 0.000000] 0: 0x00000000 -> 0x00004000 >> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. >> Total pages: 16256 >> [ 0.000000] Kernel command line: console=3DttyPSC0,115200 root=3D/=20= >> dev/sda2 rw >> [ 0.000000] MPC52xx PIC is up and running! >> [ 0.000000] PID hash table entries: 256 (order: 8, 1024 bytes) >> [ 0.000000] clocksource: timebase mult[7d00000] shift[22] =20 >> registered >> [ 0.000263] console [ttyPSC0] enabled >> [ 0.121690] Dentry cache hash table entries: 8192 (order: 3, =20 >> 32768 bytes) >> [ 0.129012] Inode-cache hash table entries: 4096 (order: 2, =20 >> 16384 bytes) >> [ 0.147433] Memory: 60844k/65536k available (3704k kernel code, >> 4624k reserved, 156k data, 117k bss, 180k init) >> [ 0.157672] SLUB: Genslabs=3D12, HWalign=3D32, Order=3D0-3, =20 >> MinObjects=3D0, >> CPUs=3D1, Nodes=3D1 >> [ 0.165373] Calibrating delay loop... 63.87 BogoMIPS (lpj=3D127744) >> [ 0.236265] Mount-cache hash table entries: 512 >> [ 0.245719] net_namespace: 288 bytes >> [ 0.250237] NET: Registered protocol family 16 >> [ 0.284887] PCI: Probing PCI hardware >> [ 0.289670] mpc52xx_pci_fixup_resources() 1057:5809 >> [ 0.294799] PCI:0000:00:17.0 Resource 0 >> 0000000050400000-00000000507fffff [21208] fixup... >> [ 0.303180] PCI:0000:00:17.0 =20 >> 0000000050400000-00000000507fffff >> [ 0.309998] PCI:0000:00:17.0 Resource 1 >> 0000000050800000-0000000050ffffff [20200] fixup... >> [ 0.318262] PCI:0000:00:17.0 =20 >> 0000000050800000-0000000050ffffff >> [ 0.325062] PCI:0000:00:17.0 Resource 2 >> 0000000060000000-000000006000000f [20101] fixup... >> [ 0.333326] PCI:0000:00:17.0 =20 >> 0000000060000000-000000006000000f >> [ 0.340124] mpc52xx_pci_fixup_resources() 104c:9065 >> [ 0.345242] PCI:0000:00:18.0 Resource 0 >> 0000000051000000-00000000513fffff [21208] fixup... >> [ 0.353519] PCI:0000:00:18.0 =20 >> 0000000051000000-00000000513fffff >> [ 0.360319] PCI:0000:00:18.0 Resource 1 >> 0000000051800000-0000000051ffffff [20200] fixup... >> [ 0.368583] PCI:0000:00:18.0 =20 >> 0000000051800000-0000000051ffffff >> [ 0.375383] PCI:0000:00:18.0 Resource 2 >> 0000000060000010-000000006000001f [20101] fixup... >> [ 0.383647] PCI:0000:00:18.0 =20 >> 0000000060000010-000000006000001f >> [ 0.390444] mpc52xx_pci_fixup_resources() 104c:9065 >> [ 0.395549] PCI:0000:00:19.0 Resource 0 >> 0000000052000000-00000000523fffff [21208] fixup... >> [ 0.403826] PCI:0000:00:19.0 =20 >> 0000000052000000-00000000523fffff >> [ 0.410626] PCI:0000:00:19.0 Resource 1 >> 0000000052800000-0000000052ffffff [20200] fixup... >> [ 0.418889] PCI:0000:00:19.0 =20 >> 0000000052800000-0000000052ffffff >> [ 0.425690] PCI:0000:00:19.0 Resource 2 >> 0000000060000020-000000006000002f [20101] fixup... >> [ 0.433954] PCI:0000:00:19.0 =20 >> 0000000060000020-000000006000002f >> [ 0.440751] mpc52xx_pci_fixup_resources() 104c:9065 >> [ 0.445854] PCI:0000:00:1a.0 Resource 0 >> 0000000053000000-00000000533fffff [21208] fixup... >> [ 0.454130] PCI:0000:00:1a.0 =20 >> 0000000053000000-00000000533fffff >> [ 0.460930] PCI:0000:00:1a.0 Resource 1 >> 0000000053800000-0000000053ffffff [20200] fixup... >> [ 0.469194] PCI:0000:00:1a.0 =20 >> 0000000053800000-0000000053ffffff >> [ 0.475994] PCI:0000:00:1a.0 Resource 2 >> 0000000060000030-000000006000003f [20101] fixup... >> [ 0.484258] PCI:0000:00:1a.0 =20 >> 0000000060000030-000000006000003f >> [ 0.491056] mpc52xx_pci_fixup_resources() 104c:9065 >> [ 0.495999] PCI: Fixup bus 0 (PHB) >> [ 0.499383] PCI: device 0000:00:16.0 OF node: <none> >> [ 0.504371] PCI: device 0000:00:17.0 OF node: <none> >> [ 0.509363] PCI: device 0000:00:18.0 OF node: <none> >> [ 0.514354] PCI: device 0000:00:19.0 OF node: <none> >> [ 0.519345] PCI: device 0000:00:1a.0 OF node: <none> >> [ 0.524332] Try to map irq for 0000:00:16.0... >> [ 0.528808] Try to map irq for 0000:00:17.0... >> [ 0.533334] -> got one, spec 3 cells (0x00000001 0x00000001...) =20= >> on >> /soc5200@f0000000/interrupt-controller@500 >> [ 0.543389] -> mapped to linux irq 65 >> [ 0.547117] Try to map irq for 0000:00:18.0... >> [ 0.551626] -> got one, spec 3 cells (0x00000001 0x00000001...) =20= >> on >> /soc5200@f0000000/interrupt-controller@500 >> [ 0.561629] -> mapped to linux irq 65 >> [ 0.565353] Try to map irq for 0000:00:19.0... >> [ 0.569858] -> got one, spec 3 cells (0x00000001 0x00000001...) =20= >> on >> /soc5200@f0000000/interrupt-controller@500 >> [ 0.579863] -> mapped to linux irq 65 >> [ 0.583587] Try to map irq for 0000:00:1a.0... >> [ 0.588099] -> got one, spec 3 cells (0x00000001 0x00000001...) =20= >> on >> /soc5200@f0000000/interrupt-controller@500 >> [ 0.598103] -> mapped to linux irq 65 >> [ 0.605144] PCI: PHB (bus 0) bridge rsrc 0: >> 0000000000000000-0000000000ffffff [0x100], parent c03a1fdc (PCI IO) >> [ 0.615266] PCI: PHB (bus 0) bridge rsrc 1: >> 0000000050000000-000000005fffffff [0x200], parent c03a1fc0 (PCI mem) >> [ 0.625539] PCI: Assigning unassigned resouces... >> [ 0.630304] bus: 00 index 0 io port: [0x00-0xffffff] >> [ 0.635299] bus: 00 index 1 mmio: [0x50000000-0x5fffffff] >> [ 0.640909] DMA: MPC52xx BestComm driver >> [ 0.645214] DMA: MPC52xx BestComm engine @f0001200 ok ! >> [ 0.678739] SCSI subsystem initialized >> [ 0.709498] NET: Registered protocol family 2 >> [ 0.754980] IP route cache hash table entries: 1024 (order: 0, =20 >> 4096 bytes) >> [ 0.762429] TCP established hash table entries: 2048 (order: 2, =20= >> 16384 bytes) >> [ 0.769716] TCP bind hash table entries: 2048 (order: 1, 8192 =20 >> bytes) >> [ 0.776224] TCP: Hash tables configured (established 2048 bind =20 >> 2048) >> [ 0.782604] TCP reno registered >> [ 0.795054] NET: Registered protocol family 1 >> [ 0.846171] JFFS2 version 2.2. (NAND) (c) 2001-2006 Red Hat, Inc. >> [ 0.855699] msgmni has been set to 118 >> [ 0.861227] alg: No test for stdrng (krng) >> [ 0.865651] io scheduler noop registered >> [ 0.869658] io scheduler anticipatory registered (default) >> [ 0.875224] io scheduler deadline registered >> [ 0.879838] io scheduler cfq registered >> [ 1.442231] Generic RTC Driver v1.07 >> [ 1.447145] Serial: MPC52xx PSC UART driver >> [ 1.451885] f0002200.serial: ttyPSC2 at MMIO 0xf0002200 (irq =3D =20= >> 130) >> is a MPC52xx PSC >> [ 1.461497] f0002400.serial: ttyPSC3 at MMIO 0xf0002400 (irq =3D =20= >> 131) >> is a MPC52xx PSC >> [ 1.471257] f0002600.serial: ttyPSC4 at MMIO 0xf0002600 (irq =3D =20= >> 139) >> is a MPC52xx PSC >> [ 1.480866] f0002800.serial: ttyPSC5 at MMIO 0xf0002800 (irq =3D =20= >> 140) >> is a MPC52xx PSC >> [ 1.490461] f0002c00.serial: ttyPSC0 at MMIO 0xf0002c00 (irq =3D =20= >> 132) >> is a MPC52xx PSC >> [ 1.521689] brd: module loaded >> [ 1.535886] loop: module loaded >> [ 1.544328] mpc52xx MII bus: probed >> [ 1.550220] net eth0: Using PHY at MDIO address 0 >> [ 1.556124] Driver 'sd' needs updating - please use bus_type =20 >> methods >> [ 1.563224] ata: MPC52xx IDE/ATA libata driver >> [ 1.568729] scsi0 : mpc52xx_ata >> [ 1.573032] ata1: PATA max UDMA/33 ata_regs 0xf0003a00 irq 135 >> [ 1.751224] ata1.00: ATA-0: TRANSCEND, 20070831, max UDMA/66 >> [ 1.756948] ata1.00: 3915072 sectors, multi 0: LBA >> [ 1.775156] ata1.00: configured for UDMA/33 >> [ 1.803154] ata1.00: configured for UDMA/33 >> [ 1.807423] ata1: EH complete >> [ 1.811300] scsi 0:0:0:0: Direct-Access ATA TRANSCEND >> 2007 PQ: 0 ANSI: 5 >> [ 1.821337] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors: >> (2.00 GB/1.86 GiB) >> [ 1.829333] sd 0:0:0:0: [sda] Write Protect is off >> [ 1.834879] sd 0:0:0:0: [sda] Write cache: disabled, read cache: >> enabled, doesn't support DPO or FUA >> [ 1.844851] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors: >> (2.00 GB/1.86 GiB) >> [ 1.852841] sd 0:0:0:0: [sda] Write Protect is off >> [ 1.858259] sd 0:0:0:0: [sda] Write cache: disabled, read cache: >> enabled, doesn't support DPO or FUA >> [ 1.867450] sda: sda1 sda2 >> [ 1.881490] sd 0:0:0:0: [sda] Attached SCSI disk >> [ 1.890711] fc000000.flash: Found 1 x16 devices at 0x0 in 8-bit =20= >> bank >> [ 1.897222] Amd/Fujitsu Extended Query Table at 0x0040 >> [ 1.902529] fc000000.flash: CFI does not contain boot bank >> location. Assuming top. >> [ 1.910147] number of CFI chips: 1 >> [ 1.913603] cfi_cmdset_0002: Disabling erase-suspend-program due =20= >> to >> code brokenness. >> [ 1.922009] RedBoot partition parsing not available >> [ 1.926998] Creating 4 MTD partitions on "fc000000.flash": >> [ 1.932547] 0x00000000-0x00500000 : "u-boot" >> [ 1.940601] 0x00500000-0x01000000 : "kernel" >> [ 1.948071] 0x01000000-0x02000000 : "rootfs" >> [ 1.955601] 0x02000000-0x03000000 : "application" >> [ 1.964240] i2c /dev entries driver >> [ 1.975775] Advanced Linux Sound Architecture Driver Version =20 >> 1.0.18rc3. >> [ 1.983814] ASoC version 0.13.2 >> [ 1.987668] tlv320aic23 0-001a: probing tlv320aic23 i2c device >> [ 2.040451] registering ASoC codec driver: >> /soc5200@f0000000/i2c@3d00/codec@1a >> [ 2.049539] ALSA device list: >> [ 2.052591] No soundcards found. >> [ 2.057430] TCP cubic registered >> [ 2.060765] NET: Registered protocol family 17 >> [ 2.066886] RPC: Registered udp transport module. >> [ 2.071683] RPC: Registered tcp transport module. >> [ 2.087086] EXT2-fs warning: mounting unchecked fs, running e2fsck >> is recommended >> [ 2.094828] VFS: Mounted root (ext2 filesystem). >> [ 2.099690] Freeing unused kernel memory: 180k init >> >> On Wed, Feb 4, 2009 at 18:54, Grant Likely =20 >> <grant.likely@secretlab.ca> wrote: >>> On Wed, Feb 4, 2009 at 9:53 AM, Tobias Knutsson >>> <tobias.knutsson@gmail.com> wrote: >>>> clock-frequency =3D <0x1e84800>; //<0>; // =46rom = boot =20 >>>> loader >>>> interrupts =3D <2 8 0 2 9 0 2 10 0>; >>>> interrupt-parent =3D <&mpc5200_pic>; >>>> bus-range =3D <0 0>; >>>> ranges =3D <0x02000000 0 0x50000000 0x50000000 0 =20 >>>> 0x10000000 >>>> 0x01000000 0 0x00000000 0x60000000 0 =20 >>>> 0x01000000>; >>>> }; >>>> >>>> The cards' memory regions are mapped out fine to different =20 >>>> addresses >>>> in the 0x50000000-0x60000000 range. However, the IO regions are =20 >>>> all mapped >>>> to zero. >>>> >>>> Do you have any idea on what could be wrong or in which direction I >>>> should be looking? >>> >>> Hmmm. Your ranges property looks okay to me. The MPC5200 setup =20 >>> code >>> may be doing the wrong thing. Turn on debug at the top of >>> arch/powerpc/platforms/mpc52xx/mpc52xx_pci.c and post your kernel >>> output. >>> >>> g. >>> >>> -- >>> Grant Likely, B.Sc., P.Eng. >>> Secret Lab Technologies Ltd. >>> >> >> >> >> -- >> >> H=C3=A4lsningar/Regards >> Tobias Knutsson >> > > > > --=20 > Grant Likely, B.Sc., P.Eng. > Secret Lab Technologies Ltd. ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: MPC5200 PCI Issues 2009-02-05 20:03 ` Tobias Knutsson @ 2009-02-06 11:46 ` Tobias Knutsson 2009-02-06 12:39 ` Tobias Knutsson 0 siblings, 1 reply; 9+ messages in thread From: Tobias Knutsson @ 2009-02-06 11:46 UTC (permalink / raw) To: Grant Likely; +Cc: linuxppc-dev@ozlabs.org Ok, I have had a breakthrough. I was trying to find out where the resources were supposed to be allocated and that was when i found this section of code in pbus_assign_resources_sorted() in drivers/pci/setup-bus.c: /* Don't touch classless devices or host bridges or ioapics. */ if (class =3D=3D PCI_CLASS_NOT_DEFINED || class =3D=3D PCI_CLASS_BRIDGE_HOST) continue; After that i took a quick look at the PCI-info reported by u-boot. Sure enough, all boards were reported having class 0. At first i tried to write a different class type, but as i suspected, the register seems to be read-only. Therefore I simply commented out the first part of the if-statement and now the resources seems to get allocated properly. However, I do realize that this is not the proper way of solving this issue. Any ideas on how to fix it without modifying any kernel code? On Thu, Feb 5, 2009 at 21:03, Tobias Knutsson <tobias.knutsson@gmail.com> w= rote: > > Hi, > > That is exactly what the bootlog shows. Debug output on in both > mpc52xx_pci.c and in pci-common.c. And the discussed code section enabled= . > > H=E4lsningar / Regards > Tobias Knutsson > > On 5 feb 2009, at 17.44, Grant Likely <grant.likely@secretlab.ca> wrote: > >> On Thu, Feb 5, 2009 at 12:06 AM, Tobias Knutsson >> <tobias.knutsson@gmail.com> wrote: >>> >>> When enabling the debug-printouts, it came to me that I forgot to >>> mention something kind of important. Using the standard mpc52xx_pci.c, >>> even the memory resources are mapped to zero. >>> >>> After disabling this code block, the memory regions are mapped out >>> fine (but still no IO): >> >> Reenable this code, enable debug in arch/powerpc/kernel/pci-common.c, >> and post the results. >> >> When this code is disabled then you're just getting the leftovers from >> U-Boot's scan of the PCI bus. For MPC5200 support Linux does its own >> scan and its own allocation of memory/IO address space and this code >> is needed to make sure that happens. >> >> g. >> >>> >>> static void >>> mpc52xx_pci_fixup_resources(struct pci_dev *dev) >>> { >>> int i; >>> >>> pr_debug("mpc52xx_pci_fixup_resources() %.4x:%.4x\n", >>> dev->vendor, dev->device); >>> >>> /* We don't rely on boot loader for PCI and resets all >>> devices */ >>> for (i =3D 0; i < DEVICE_COUNT_RESOURCE; i++) { >>> struct resource *res =3D &dev->resource[i]; >>> if (res->end > res->start) { /* Only valid resources */ >>> res->end -=3D res->start; >>> res->start =3D 0; >>> res->flags |=3D IORESOURCE_UNSET; >>> } >>> } >>> >>> What is the purpose of this code? Since all resources are reset here, >>> where are they inteded to be re-allocated? >>> >>> Here is the bootlog with the aforementioned code enabled: >>> >>> >>> reading cuImage.lite5200b >>> >>> 1833699 bytes read >>> ## Booting kernel from Legacy Image at 00201400 ... >>> Image Name: Linux-2.6.28 >>> Created: 2009-02-05 6:54:20 UTC >>> Image Type: PowerPC Linux Kernel Image (gzip compressed) >>> Data Size: 1833635 Bytes =3D 1.7 MB >>> Load Address: 00400000 >>> Entry Point: 004005a0 >>> Verifying Checksum ... OK >>> Uncompressing Kernel Image ... OK >>> [ 0.000000] Using lite5200 machine description >>> [ 0.000000] Linux version 2.6.28 (tknutsson@ztn-ubuntu) (gcc >>> version 4.3.2 (Sourcery G++ Lite 4.3-50) ) #66 Thu Feb 5 07:51:46 CET >>> 2009 >>> [ 0.000000] Adding MPC52xx PCI host bridge /pci@f0000d00 >>> [ 0.000000] PCI host bridge /pci@f0000d00 (primary) ranges: >>> [ 0.000000] MEM 0x0000000050000000..0x000000005fffffff -> >>> 0x0000000050000000 >>> [ 0.000000] IO 0x0000000060000000..0x0000000060ffffff -> >>> 0x0000000000000000 >>> [ 0.000000] mpc52xx_pci_setup(hose=3Dc03ec000, pci_regs=3Dfdffad00) >>> [ 0.000000] mem_resource[0] =3D {.start=3D50000000, .end=3D5fffffff, >>> .flags=3D200} >>> [ 0.000000] .io_resource=3D{.start=3D0,.end=3Dffffff,.flags=3D100} >>> .io_base_phys=3D0x60000000 >>> [ 0.000000] Zone PFN ranges: >>> [ 0.000000] DMA 0x00000000 -> 0x00004000 >>> [ 0.000000] Normal 0x00004000 -> 0x00004000 >>> [ 0.000000] Movable zone start PFN for each node >>> [ 0.000000] early_node_map[1] active PFN ranges >>> [ 0.000000] 0: 0x00000000 -> 0x00004000 >>> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. >>> Total pages: 16256 >>> [ 0.000000] Kernel command line: console=3DttyPSC0,115200 root=3D/de= v/sda2 >>> rw >>> [ 0.000000] MPC52xx PIC is up and running! >>> [ 0.000000] PID hash table entries: 256 (order: 8, 1024 bytes) >>> [ 0.000000] clocksource: timebase mult[7d00000] shift[22] registered >>> [ 0.000263] console [ttyPSC0] enabled >>> [ 0.121690] Dentry cache hash table entries: 8192 (order: 3, 32768 >>> bytes) >>> [ 0.129012] Inode-cache hash table entries: 4096 (order: 2, 16384 >>> bytes) >>> [ 0.147433] Memory: 60844k/65536k available (3704k kernel code, >>> 4624k reserved, 156k data, 117k bss, 180k init) >>> [ 0.157672] SLUB: Genslabs=3D12, HWalign=3D32, Order=3D0-3, MinObjec= ts=3D0, >>> CPUs=3D1, Nodes=3D1 >>> [ 0.165373] Calibrating delay loop... 63.87 BogoMIPS (lpj=3D127744) >>> [ 0.236265] Mount-cache hash table entries: 512 >>> [ 0.245719] net_namespace: 288 bytes >>> [ 0.250237] NET: Registered protocol family 16 >>> [ 0.284887] PCI: Probing PCI hardware >>> [ 0.289670] mpc52xx_pci_fixup_resources() 1057:5809 >>> [ 0.294799] PCI:0000:00:17.0 Resource 0 >>> 0000000050400000-00000000507fffff [21208] fixup... >>> [ 0.303180] PCI:0000:00:17.0 >>> 0000000050400000-00000000507fffff >>> [ 0.309998] PCI:0000:00:17.0 Resource 1 >>> 0000000050800000-0000000050ffffff [20200] fixup... >>> [ 0.318262] PCI:0000:00:17.0 >>> 0000000050800000-0000000050ffffff >>> [ 0.325062] PCI:0000:00:17.0 Resource 2 >>> 0000000060000000-000000006000000f [20101] fixup... >>> [ 0.333326] PCI:0000:00:17.0 >>> 0000000060000000-000000006000000f >>> [ 0.340124] mpc52xx_pci_fixup_resources() 104c:9065 >>> [ 0.345242] PCI:0000:00:18.0 Resource 0 >>> 0000000051000000-00000000513fffff [21208] fixup... >>> [ 0.353519] PCI:0000:00:18.0 >>> 0000000051000000-00000000513fffff >>> [ 0.360319] PCI:0000:00:18.0 Resource 1 >>> 0000000051800000-0000000051ffffff [20200] fixup... >>> [ 0.368583] PCI:0000:00:18.0 >>> 0000000051800000-0000000051ffffff >>> [ 0.375383] PCI:0000:00:18.0 Resource 2 >>> 0000000060000010-000000006000001f [20101] fixup... >>> [ 0.383647] PCI:0000:00:18.0 >>> 0000000060000010-000000006000001f >>> [ 0.390444] mpc52xx_pci_fixup_resources() 104c:9065 >>> [ 0.395549] PCI:0000:00:19.0 Resource 0 >>> 0000000052000000-00000000523fffff [21208] fixup... >>> [ 0.403826] PCI:0000:00:19.0 >>> 0000000052000000-00000000523fffff >>> [ 0.410626] PCI:0000:00:19.0 Resource 1 >>> 0000000052800000-0000000052ffffff [20200] fixup... >>> [ 0.418889] PCI:0000:00:19.0 >>> 0000000052800000-0000000052ffffff >>> [ 0.425690] PCI:0000:00:19.0 Resource 2 >>> 0000000060000020-000000006000002f [20101] fixup... >>> [ 0.433954] PCI:0000:00:19.0 >>> 0000000060000020-000000006000002f >>> [ 0.440751] mpc52xx_pci_fixup_resources() 104c:9065 >>> [ 0.445854] PCI:0000:00:1a.0 Resource 0 >>> 0000000053000000-00000000533fffff [21208] fixup... >>> [ 0.454130] PCI:0000:00:1a.0 >>> 0000000053000000-00000000533fffff >>> [ 0.460930] PCI:0000:00:1a.0 Resource 1 >>> 0000000053800000-0000000053ffffff [20200] fixup... >>> [ 0.469194] PCI:0000:00:1a.0 >>> 0000000053800000-0000000053ffffff >>> [ 0.475994] PCI:0000:00:1a.0 Resource 2 >>> 0000000060000030-000000006000003f [20101] fixup... >>> [ 0.484258] PCI:0000:00:1a.0 >>> 0000000060000030-000000006000003f >>> [ 0.491056] mpc52xx_pci_fixup_resources() 104c:9065 >>> [ 0.495999] PCI: Fixup bus 0 (PHB) >>> [ 0.499383] PCI: device 0000:00:16.0 OF node: <none> >>> [ 0.504371] PCI: device 0000:00:17.0 OF node: <none> >>> [ 0.509363] PCI: device 0000:00:18.0 OF node: <none> >>> [ 0.514354] PCI: device 0000:00:19.0 OF node: <none> >>> [ 0.519345] PCI: device 0000:00:1a.0 OF node: <none> >>> [ 0.524332] Try to map irq for 0000:00:16.0... >>> [ 0.528808] Try to map irq for 0000:00:17.0... >>> [ 0.533334] -> got one, spec 3 cells (0x00000001 0x00000001...) on >>> /soc5200@f0000000/interrupt-controller@500 >>> [ 0.543389] -> mapped to linux irq 65 >>> [ 0.547117] Try to map irq for 0000:00:18.0... >>> [ 0.551626] -> got one, spec 3 cells (0x00000001 0x00000001...) on >>> /soc5200@f0000000/interrupt-controller@500 >>> [ 0.561629] -> mapped to linux irq 65 >>> [ 0.565353] Try to map irq for 0000:00:19.0... >>> [ 0.569858] -> got one, spec 3 cells (0x00000001 0x00000001...) on >>> /soc5200@f0000000/interrupt-controller@500 >>> [ 0.579863] -> mapped to linux irq 65 >>> [ 0.583587] Try to map irq for 0000:00:1a.0... >>> [ 0.588099] -> got one, spec 3 cells (0x00000001 0x00000001...) on >>> /soc5200@f0000000/interrupt-controller@500 >>> [ 0.598103] -> mapped to linux irq 65 >>> [ 0.605144] PCI: PHB (bus 0) bridge rsrc 0: >>> 0000000000000000-0000000000ffffff [0x100], parent c03a1fdc (PCI IO) >>> [ 0.615266] PCI: PHB (bus 0) bridge rsrc 1: >>> 0000000050000000-000000005fffffff [0x200], parent c03a1fc0 (PCI mem) >>> [ 0.625539] PCI: Assigning unassigned resouces... >>> [ 0.630304] bus: 00 index 0 io port: [0x00-0xffffff] >>> [ 0.635299] bus: 00 index 1 mmio: [0x50000000-0x5fffffff] >>> [ 0.640909] DMA: MPC52xx BestComm driver >>> [ 0.645214] DMA: MPC52xx BestComm engine @f0001200 ok ! >>> [ 0.678739] SCSI subsystem initialized >>> [ 0.709498] NET: Registered protocol family 2 >>> [ 0.754980] IP route cache hash table entries: 1024 (order: 0, 4096 >>> bytes) >>> [ 0.762429] TCP established hash table entries: 2048 (order: 2, 1638= 4 >>> bytes) >>> [ 0.769716] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) >>> [ 0.776224] TCP: Hash tables configured (established 2048 bind 2048) >>> [ 0.782604] TCP reno registered >>> [ 0.795054] NET: Registered protocol family 1 >>> [ 0.846171] JFFS2 version 2.2. (NAND) (c) 2001-2006 Red Hat, Inc. >>> [ 0.855699] msgmni has been set to 118 >>> [ 0.861227] alg: No test for stdrng (krng) >>> [ 0.865651] io scheduler noop registered >>> [ 0.869658] io scheduler anticipatory registered (default) >>> [ 0.875224] io scheduler deadline registered >>> [ 0.879838] io scheduler cfq registered >>> [ 1.442231] Generic RTC Driver v1.07 >>> [ 1.447145] Serial: MPC52xx PSC UART driver >>> [ 1.451885] f0002200.serial: ttyPSC2 at MMIO 0xf0002200 (irq =3D 130= ) >>> is a MPC52xx PSC >>> [ 1.461497] f0002400.serial: ttyPSC3 at MMIO 0xf0002400 (irq =3D 131= ) >>> is a MPC52xx PSC >>> [ 1.471257] f0002600.serial: ttyPSC4 at MMIO 0xf0002600 (irq =3D 139= ) >>> is a MPC52xx PSC >>> [ 1.480866] f0002800.serial: ttyPSC5 at MMIO 0xf0002800 (irq =3D 140= ) >>> is a MPC52xx PSC >>> [ 1.490461] f0002c00.serial: ttyPSC0 at MMIO 0xf0002c00 (irq =3D 132= ) >>> is a MPC52xx PSC >>> [ 1.521689] brd: module loaded >>> [ 1.535886] loop: module loaded >>> [ 1.544328] mpc52xx MII bus: probed >>> [ 1.550220] net eth0: Using PHY at MDIO address 0 >>> [ 1.556124] Driver 'sd' needs updating - please use bus_type methods >>> [ 1.563224] ata: MPC52xx IDE/ATA libata driver >>> [ 1.568729] scsi0 : mpc52xx_ata >>> [ 1.573032] ata1: PATA max UDMA/33 ata_regs 0xf0003a00 irq 135 >>> [ 1.751224] ata1.00: ATA-0: TRANSCEND, 20070831, max UDMA/66 >>> [ 1.756948] ata1.00: 3915072 sectors, multi 0: LBA >>> [ 1.775156] ata1.00: configured for UDMA/33 >>> [ 1.803154] ata1.00: configured for UDMA/33 >>> [ 1.807423] ata1: EH complete >>> [ 1.811300] scsi 0:0:0:0: Direct-Access ATA TRANSCEND >>> 2007 PQ: 0 ANSI: 5 >>> [ 1.821337] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors: >>> (2.00 GB/1.86 GiB) >>> [ 1.829333] sd 0:0:0:0: [sda] Write Protect is off >>> [ 1.834879] sd 0:0:0:0: [sda] Write cache: disabled, read cache: >>> enabled, doesn't support DPO or FUA >>> [ 1.844851] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors: >>> (2.00 GB/1.86 GiB) >>> [ 1.852841] sd 0:0:0:0: [sda] Write Protect is off >>> [ 1.858259] sd 0:0:0:0: [sda] Write cache: disabled, read cache: >>> enabled, doesn't support DPO or FUA >>> [ 1.867450] sda: sda1 sda2 >>> [ 1.881490] sd 0:0:0:0: [sda] Attached SCSI disk >>> [ 1.890711] fc000000.flash: Found 1 x16 devices at 0x0 in 8-bit bank >>> [ 1.897222] Amd/Fujitsu Extended Query Table at 0x0040 >>> [ 1.902529] fc000000.flash: CFI does not contain boot bank >>> location. Assuming top. >>> [ 1.910147] number of CFI chips: 1 >>> [ 1.913603] cfi_cmdset_0002: Disabling erase-suspend-program due to >>> code brokenness. >>> [ 1.922009] RedBoot partition parsing not available >>> [ 1.926998] Creating 4 MTD partitions on "fc000000.flash": >>> [ 1.932547] 0x00000000-0x00500000 : "u-boot" >>> [ 1.940601] 0x00500000-0x01000000 : "kernel" >>> [ 1.948071] 0x01000000-0x02000000 : "rootfs" >>> [ 1.955601] 0x02000000-0x03000000 : "application" >>> [ 1.964240] i2c /dev entries driver >>> [ 1.975775] Advanced Linux Sound Architecture Driver Version >>> 1.0.18rc3. >>> [ 1.983814] ASoC version 0.13.2 >>> [ 1.987668] tlv320aic23 0-001a: probing tlv320aic23 i2c device >>> [ 2.040451] registering ASoC codec driver: >>> /soc5200@f0000000/i2c@3d00/codec@1a >>> [ 2.049539] ALSA device list: >>> [ 2.052591] No soundcards found. >>> [ 2.057430] TCP cubic registered >>> [ 2.060765] NET: Registered protocol family 17 >>> [ 2.066886] RPC: Registered udp transport module. >>> [ 2.071683] RPC: Registered tcp transport module. >>> [ 2.087086] EXT2-fs warning: mounting unchecked fs, running e2fsck >>> is recommended >>> [ 2.094828] VFS: Mounted root (ext2 filesystem). >>> [ 2.099690] Freeing unused kernel memory: 180k init >>> >>> On Wed, Feb 4, 2009 at 18:54, Grant Likely <grant.likely@secretlab.ca> >>> wrote: >>>> >>>> On Wed, Feb 4, 2009 at 9:53 AM, Tobias Knutsson >>>> <tobias.knutsson@gmail.com> wrote: >>>>> >>>>> clock-frequency =3D <0x1e84800>; //<0>; // From boot loa= der >>>>> interrupts =3D <2 8 0 2 9 0 2 10 0>; >>>>> interrupt-parent =3D <&mpc5200_pic>; >>>>> bus-range =3D <0 0>; >>>>> ranges =3D <0x02000000 0 0x50000000 0x50000000 0 0x100000= 00 >>>>> 0x01000000 0 0x00000000 0x60000000 0 0x01000000= >; >>>>> }; >>>>> >>>>> The cards' memory regions are mapped out fine to different addresses >>>>> in the 0x50000000-0x60000000 range. However, the IO regions are all >>>>> mapped >>>>> to zero. >>>>> >>>>> Do you have any idea on what could be wrong or in which direction I >>>>> should be looking? >>>> >>>> Hmmm. Your ranges property looks okay to me. The MPC5200 setup code >>>> may be doing the wrong thing. Turn on debug at the top of >>>> arch/powerpc/platforms/mpc52xx/mpc52xx_pci.c and post your kernel >>>> output. >>>> >>>> g. >>>> >>>> -- >>>> Grant Likely, B.Sc., P.Eng. >>>> Secret Lab Technologies Ltd. >>>> >>> >>> >>> >>> -- >>> >>> H=E4lsningar/Regards >>> Tobias Knutsson >>> >> >> >> >> -- >> Grant Likely, B.Sc., P.Eng. >> Secret Lab Technologies Ltd. > --=20 H=E4lsningar/Regards Tobias Knutsson ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: MPC5200 PCI Issues 2009-02-06 11:46 ` Tobias Knutsson @ 2009-02-06 12:39 ` Tobias Knutsson 0 siblings, 0 replies; 9+ messages in thread From: Tobias Knutsson @ 2009-02-06 12:39 UTC (permalink / raw) To: Grant Likely; +Cc: linuxppc-dev@ozlabs.org I have now found drivers/pci/quirks.c which seems to be the place for these types of things. However, since this code is unlikely to ever make it to mainline, is it possible to register a fixup hook in a platform setup file (lite5200.c and friends)? On Fri, Feb 6, 2009 at 12:46, Tobias Knutsson <tobias.knutsson@gmail.com> w= rote: > Ok, I have had a breakthrough. I was trying to find out where the > resources were supposed to be allocated and that was when i found this > section of code in pbus_assign_resources_sorted() in > drivers/pci/setup-bus.c: > > /* Don't touch classless devices or host bridges or ioapic= s. */ > if (class =3D=3D PCI_CLASS_NOT_DEFINED || > class =3D=3D PCI_CLASS_BRIDGE_HOST) > continue; > > After that i took a quick look at the PCI-info reported by u-boot. > Sure enough, all boards were reported having class 0. At first i tried > to write a different class type, but as i suspected, the register > seems to be read-only. Therefore I simply commented out the first part > of the if-statement and now the resources seems to get allocated > properly. > > However, I do realize that this is not the proper way of solving this > issue. Any ideas on how to fix it without modifying any kernel code? > > > On Thu, Feb 5, 2009 at 21:03, Tobias Knutsson <tobias.knutsson@gmail.com>= wrote: >> >> Hi, >> >> That is exactly what the bootlog shows. Debug output on in both >> mpc52xx_pci.c and in pci-common.c. And the discussed code section enable= d. >> >> H=E4lsningar / Regards >> Tobias Knutsson >> >> On 5 feb 2009, at 17.44, Grant Likely <grant.likely@secretlab.ca> wrote: >> >>> On Thu, Feb 5, 2009 at 12:06 AM, Tobias Knutsson >>> <tobias.knutsson@gmail.com> wrote: >>>> >>>> When enabling the debug-printouts, it came to me that I forgot to >>>> mention something kind of important. Using the standard mpc52xx_pci.c, >>>> even the memory resources are mapped to zero. >>>> >>>> After disabling this code block, the memory regions are mapped out >>>> fine (but still no IO): >>> >>> Reenable this code, enable debug in arch/powerpc/kernel/pci-common.c, >>> and post the results. >>> >>> When this code is disabled then you're just getting the leftovers from >>> U-Boot's scan of the PCI bus. For MPC5200 support Linux does its own >>> scan and its own allocation of memory/IO address space and this code >>> is needed to make sure that happens. >>> >>> g. >>> >>>> >>>> static void >>>> mpc52xx_pci_fixup_resources(struct pci_dev *dev) >>>> { >>>> int i; >>>> >>>> pr_debug("mpc52xx_pci_fixup_resources() %.4x:%.4x\n", >>>> dev->vendor, dev->device); >>>> >>>> /* We don't rely on boot loader for PCI and resets all >>>> devices */ >>>> for (i =3D 0; i < DEVICE_COUNT_RESOURCE; i++) { >>>> struct resource *res =3D &dev->resource[i]; >>>> if (res->end > res->start) { /* Only valid resources *= / >>>> res->end -=3D res->start; >>>> res->start =3D 0; >>>> res->flags |=3D IORESOURCE_UNSET; >>>> } >>>> } >>>> >>>> What is the purpose of this code? Since all resources are reset here, >>>> where are they inteded to be re-allocated? >>>> >>>> Here is the bootlog with the aforementioned code enabled: >>>> >>>> >>>> reading cuImage.lite5200b >>>> >>>> 1833699 bytes read >>>> ## Booting kernel from Legacy Image at 00201400 ... >>>> Image Name: Linux-2.6.28 >>>> Created: 2009-02-05 6:54:20 UTC >>>> Image Type: PowerPC Linux Kernel Image (gzip compressed) >>>> Data Size: 1833635 Bytes =3D 1.7 MB >>>> Load Address: 00400000 >>>> Entry Point: 004005a0 >>>> Verifying Checksum ... OK >>>> Uncompressing Kernel Image ... OK >>>> [ 0.000000] Using lite5200 machine description >>>> [ 0.000000] Linux version 2.6.28 (tknutsson@ztn-ubuntu) (gcc >>>> version 4.3.2 (Sourcery G++ Lite 4.3-50) ) #66 Thu Feb 5 07:51:46 CET >>>> 2009 >>>> [ 0.000000] Adding MPC52xx PCI host bridge /pci@f0000d00 >>>> [ 0.000000] PCI host bridge /pci@f0000d00 (primary) ranges: >>>> [ 0.000000] MEM 0x0000000050000000..0x000000005fffffff -> >>>> 0x0000000050000000 >>>> [ 0.000000] IO 0x0000000060000000..0x0000000060ffffff -> >>>> 0x0000000000000000 >>>> [ 0.000000] mpc52xx_pci_setup(hose=3Dc03ec000, pci_regs=3Dfdffad00) >>>> [ 0.000000] mem_resource[0] =3D {.start=3D50000000, .end=3D5fffffff= , >>>> .flags=3D200} >>>> [ 0.000000] .io_resource=3D{.start=3D0,.end=3Dffffff,.flags=3D100} >>>> .io_base_phys=3D0x60000000 >>>> [ 0.000000] Zone PFN ranges: >>>> [ 0.000000] DMA 0x00000000 -> 0x00004000 >>>> [ 0.000000] Normal 0x00004000 -> 0x00004000 >>>> [ 0.000000] Movable zone start PFN for each node >>>> [ 0.000000] early_node_map[1] active PFN ranges >>>> [ 0.000000] 0: 0x00000000 -> 0x00004000 >>>> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. >>>> Total pages: 16256 >>>> [ 0.000000] Kernel command line: console=3DttyPSC0,115200 root=3D/d= ev/sda2 >>>> rw >>>> [ 0.000000] MPC52xx PIC is up and running! >>>> [ 0.000000] PID hash table entries: 256 (order: 8, 1024 bytes) >>>> [ 0.000000] clocksource: timebase mult[7d00000] shift[22] registere= d >>>> [ 0.000263] console [ttyPSC0] enabled >>>> [ 0.121690] Dentry cache hash table entries: 8192 (order: 3, 32768 >>>> bytes) >>>> [ 0.129012] Inode-cache hash table entries: 4096 (order: 2, 16384 >>>> bytes) >>>> [ 0.147433] Memory: 60844k/65536k available (3704k kernel code, >>>> 4624k reserved, 156k data, 117k bss, 180k init) >>>> [ 0.157672] SLUB: Genslabs=3D12, HWalign=3D32, Order=3D0-3, MinObje= cts=3D0, >>>> CPUs=3D1, Nodes=3D1 >>>> [ 0.165373] Calibrating delay loop... 63.87 BogoMIPS (lpj=3D127744) >>>> [ 0.236265] Mount-cache hash table entries: 512 >>>> [ 0.245719] net_namespace: 288 bytes >>>> [ 0.250237] NET: Registered protocol family 16 >>>> [ 0.284887] PCI: Probing PCI hardware >>>> [ 0.289670] mpc52xx_pci_fixup_resources() 1057:5809 >>>> [ 0.294799] PCI:0000:00:17.0 Resource 0 >>>> 0000000050400000-00000000507fffff [21208] fixup... >>>> [ 0.303180] PCI:0000:00:17.0 >>>> 0000000050400000-00000000507fffff >>>> [ 0.309998] PCI:0000:00:17.0 Resource 1 >>>> 0000000050800000-0000000050ffffff [20200] fixup... >>>> [ 0.318262] PCI:0000:00:17.0 >>>> 0000000050800000-0000000050ffffff >>>> [ 0.325062] PCI:0000:00:17.0 Resource 2 >>>> 0000000060000000-000000006000000f [20101] fixup... >>>> [ 0.333326] PCI:0000:00:17.0 >>>> 0000000060000000-000000006000000f >>>> [ 0.340124] mpc52xx_pci_fixup_resources() 104c:9065 >>>> [ 0.345242] PCI:0000:00:18.0 Resource 0 >>>> 0000000051000000-00000000513fffff [21208] fixup... >>>> [ 0.353519] PCI:0000:00:18.0 >>>> 0000000051000000-00000000513fffff >>>> [ 0.360319] PCI:0000:00:18.0 Resource 1 >>>> 0000000051800000-0000000051ffffff [20200] fixup... >>>> [ 0.368583] PCI:0000:00:18.0 >>>> 0000000051800000-0000000051ffffff >>>> [ 0.375383] PCI:0000:00:18.0 Resource 2 >>>> 0000000060000010-000000006000001f [20101] fixup... >>>> [ 0.383647] PCI:0000:00:18.0 >>>> 0000000060000010-000000006000001f >>>> [ 0.390444] mpc52xx_pci_fixup_resources() 104c:9065 >>>> [ 0.395549] PCI:0000:00:19.0 Resource 0 >>>> 0000000052000000-00000000523fffff [21208] fixup... >>>> [ 0.403826] PCI:0000:00:19.0 >>>> 0000000052000000-00000000523fffff >>>> [ 0.410626] PCI:0000:00:19.0 Resource 1 >>>> 0000000052800000-0000000052ffffff [20200] fixup... >>>> [ 0.418889] PCI:0000:00:19.0 >>>> 0000000052800000-0000000052ffffff >>>> [ 0.425690] PCI:0000:00:19.0 Resource 2 >>>> 0000000060000020-000000006000002f [20101] fixup... >>>> [ 0.433954] PCI:0000:00:19.0 >>>> 0000000060000020-000000006000002f >>>> [ 0.440751] mpc52xx_pci_fixup_resources() 104c:9065 >>>> [ 0.445854] PCI:0000:00:1a.0 Resource 0 >>>> 0000000053000000-00000000533fffff [21208] fixup... >>>> [ 0.454130] PCI:0000:00:1a.0 >>>> 0000000053000000-00000000533fffff >>>> [ 0.460930] PCI:0000:00:1a.0 Resource 1 >>>> 0000000053800000-0000000053ffffff [20200] fixup... >>>> [ 0.469194] PCI:0000:00:1a.0 >>>> 0000000053800000-0000000053ffffff >>>> [ 0.475994] PCI:0000:00:1a.0 Resource 2 >>>> 0000000060000030-000000006000003f [20101] fixup... >>>> [ 0.484258] PCI:0000:00:1a.0 >>>> 0000000060000030-000000006000003f >>>> [ 0.491056] mpc52xx_pci_fixup_resources() 104c:9065 >>>> [ 0.495999] PCI: Fixup bus 0 (PHB) >>>> [ 0.499383] PCI: device 0000:00:16.0 OF node: <none> >>>> [ 0.504371] PCI: device 0000:00:17.0 OF node: <none> >>>> [ 0.509363] PCI: device 0000:00:18.0 OF node: <none> >>>> [ 0.514354] PCI: device 0000:00:19.0 OF node: <none> >>>> [ 0.519345] PCI: device 0000:00:1a.0 OF node: <none> >>>> [ 0.524332] Try to map irq for 0000:00:16.0... >>>> [ 0.528808] Try to map irq for 0000:00:17.0... >>>> [ 0.533334] -> got one, spec 3 cells (0x00000001 0x00000001...) on >>>> /soc5200@f0000000/interrupt-controller@500 >>>> [ 0.543389] -> mapped to linux irq 65 >>>> [ 0.547117] Try to map irq for 0000:00:18.0... >>>> [ 0.551626] -> got one, spec 3 cells (0x00000001 0x00000001...) on >>>> /soc5200@f0000000/interrupt-controller@500 >>>> [ 0.561629] -> mapped to linux irq 65 >>>> [ 0.565353] Try to map irq for 0000:00:19.0... >>>> [ 0.569858] -> got one, spec 3 cells (0x00000001 0x00000001...) on >>>> /soc5200@f0000000/interrupt-controller@500 >>>> [ 0.579863] -> mapped to linux irq 65 >>>> [ 0.583587] Try to map irq for 0000:00:1a.0... >>>> [ 0.588099] -> got one, spec 3 cells (0x00000001 0x00000001...) on >>>> /soc5200@f0000000/interrupt-controller@500 >>>> [ 0.598103] -> mapped to linux irq 65 >>>> [ 0.605144] PCI: PHB (bus 0) bridge rsrc 0: >>>> 0000000000000000-0000000000ffffff [0x100], parent c03a1fdc (PCI IO) >>>> [ 0.615266] PCI: PHB (bus 0) bridge rsrc 1: >>>> 0000000050000000-000000005fffffff [0x200], parent c03a1fc0 (PCI mem) >>>> [ 0.625539] PCI: Assigning unassigned resouces... >>>> [ 0.630304] bus: 00 index 0 io port: [0x00-0xffffff] >>>> [ 0.635299] bus: 00 index 1 mmio: [0x50000000-0x5fffffff] >>>> [ 0.640909] DMA: MPC52xx BestComm driver >>>> [ 0.645214] DMA: MPC52xx BestComm engine @f0001200 ok ! >>>> [ 0.678739] SCSI subsystem initialized >>>> [ 0.709498] NET: Registered protocol family 2 >>>> [ 0.754980] IP route cache hash table entries: 1024 (order: 0, 4096 >>>> bytes) >>>> [ 0.762429] TCP established hash table entries: 2048 (order: 2, 163= 84 >>>> bytes) >>>> [ 0.769716] TCP bind hash table entries: 2048 (order: 1, 8192 bytes= ) >>>> [ 0.776224] TCP: Hash tables configured (established 2048 bind 2048= ) >>>> [ 0.782604] TCP reno registered >>>> [ 0.795054] NET: Registered protocol family 1 >>>> [ 0.846171] JFFS2 version 2.2. (NAND) (c) 2001-2006 Red Hat, Inc. >>>> [ 0.855699] msgmni has been set to 118 >>>> [ 0.861227] alg: No test for stdrng (krng) >>>> [ 0.865651] io scheduler noop registered >>>> [ 0.869658] io scheduler anticipatory registered (default) >>>> [ 0.875224] io scheduler deadline registered >>>> [ 0.879838] io scheduler cfq registered >>>> [ 1.442231] Generic RTC Driver v1.07 >>>> [ 1.447145] Serial: MPC52xx PSC UART driver >>>> [ 1.451885] f0002200.serial: ttyPSC2 at MMIO 0xf0002200 (irq =3D 13= 0) >>>> is a MPC52xx PSC >>>> [ 1.461497] f0002400.serial: ttyPSC3 at MMIO 0xf0002400 (irq =3D 13= 1) >>>> is a MPC52xx PSC >>>> [ 1.471257] f0002600.serial: ttyPSC4 at MMIO 0xf0002600 (irq =3D 13= 9) >>>> is a MPC52xx PSC >>>> [ 1.480866] f0002800.serial: ttyPSC5 at MMIO 0xf0002800 (irq =3D 14= 0) >>>> is a MPC52xx PSC >>>> [ 1.490461] f0002c00.serial: ttyPSC0 at MMIO 0xf0002c00 (irq =3D 13= 2) >>>> is a MPC52xx PSC >>>> [ 1.521689] brd: module loaded >>>> [ 1.535886] loop: module loaded >>>> [ 1.544328] mpc52xx MII bus: probed >>>> [ 1.550220] net eth0: Using PHY at MDIO address 0 >>>> [ 1.556124] Driver 'sd' needs updating - please use bus_type method= s >>>> [ 1.563224] ata: MPC52xx IDE/ATA libata driver >>>> [ 1.568729] scsi0 : mpc52xx_ata >>>> [ 1.573032] ata1: PATA max UDMA/33 ata_regs 0xf0003a00 irq 135 >>>> [ 1.751224] ata1.00: ATA-0: TRANSCEND, 20070831, max UDMA/66 >>>> [ 1.756948] ata1.00: 3915072 sectors, multi 0: LBA >>>> [ 1.775156] ata1.00: configured for UDMA/33 >>>> [ 1.803154] ata1.00: configured for UDMA/33 >>>> [ 1.807423] ata1: EH complete >>>> [ 1.811300] scsi 0:0:0:0: Direct-Access ATA TRANSCEND >>>> 2007 PQ: 0 ANSI: 5 >>>> [ 1.821337] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors: >>>> (2.00 GB/1.86 GiB) >>>> [ 1.829333] sd 0:0:0:0: [sda] Write Protect is off >>>> [ 1.834879] sd 0:0:0:0: [sda] Write cache: disabled, read cache: >>>> enabled, doesn't support DPO or FUA >>>> [ 1.844851] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors: >>>> (2.00 GB/1.86 GiB) >>>> [ 1.852841] sd 0:0:0:0: [sda] Write Protect is off >>>> [ 1.858259] sd 0:0:0:0: [sda] Write cache: disabled, read cache: >>>> enabled, doesn't support DPO or FUA >>>> [ 1.867450] sda: sda1 sda2 >>>> [ 1.881490] sd 0:0:0:0: [sda] Attached SCSI disk >>>> [ 1.890711] fc000000.flash: Found 1 x16 devices at 0x0 in 8-bit ban= k >>>> [ 1.897222] Amd/Fujitsu Extended Query Table at 0x0040 >>>> [ 1.902529] fc000000.flash: CFI does not contain boot bank >>>> location. Assuming top. >>>> [ 1.910147] number of CFI chips: 1 >>>> [ 1.913603] cfi_cmdset_0002: Disabling erase-suspend-program due to >>>> code brokenness. >>>> [ 1.922009] RedBoot partition parsing not available >>>> [ 1.926998] Creating 4 MTD partitions on "fc000000.flash": >>>> [ 1.932547] 0x00000000-0x00500000 : "u-boot" >>>> [ 1.940601] 0x00500000-0x01000000 : "kernel" >>>> [ 1.948071] 0x01000000-0x02000000 : "rootfs" >>>> [ 1.955601] 0x02000000-0x03000000 : "application" >>>> [ 1.964240] i2c /dev entries driver >>>> [ 1.975775] Advanced Linux Sound Architecture Driver Version >>>> 1.0.18rc3. >>>> [ 1.983814] ASoC version 0.13.2 >>>> [ 1.987668] tlv320aic23 0-001a: probing tlv320aic23 i2c device >>>> [ 2.040451] registering ASoC codec driver: >>>> /soc5200@f0000000/i2c@3d00/codec@1a >>>> [ 2.049539] ALSA device list: >>>> [ 2.052591] No soundcards found. >>>> [ 2.057430] TCP cubic registered >>>> [ 2.060765] NET: Registered protocol family 17 >>>> [ 2.066886] RPC: Registered udp transport module. >>>> [ 2.071683] RPC: Registered tcp transport module. >>>> [ 2.087086] EXT2-fs warning: mounting unchecked fs, running e2fsck >>>> is recommended >>>> [ 2.094828] VFS: Mounted root (ext2 filesystem). >>>> [ 2.099690] Freeing unused kernel memory: 180k init >>>> >>>> On Wed, Feb 4, 2009 at 18:54, Grant Likely <grant.likely@secretlab.ca> >>>> wrote: >>>>> >>>>> On Wed, Feb 4, 2009 at 9:53 AM, Tobias Knutsson >>>>> <tobias.knutsson@gmail.com> wrote: >>>>>> >>>>>> clock-frequency =3D <0x1e84800>; //<0>; // From boot lo= ader >>>>>> interrupts =3D <2 8 0 2 9 0 2 10 0>; >>>>>> interrupt-parent =3D <&mpc5200_pic>; >>>>>> bus-range =3D <0 0>; >>>>>> ranges =3D <0x02000000 0 0x50000000 0x50000000 0 0x10000= 000 >>>>>> 0x01000000 0 0x00000000 0x60000000 0 0x0100000= 0>; >>>>>> }; >>>>>> >>>>>> The cards' memory regions are mapped out fine to different addresses >>>>>> in the 0x50000000-0x60000000 range. However, the IO regions are all >>>>>> mapped >>>>>> to zero. >>>>>> >>>>>> Do you have any idea on what could be wrong or in which direction I >>>>>> should be looking? >>>>> >>>>> Hmmm. Your ranges property looks okay to me. The MPC5200 setup code >>>>> may be doing the wrong thing. Turn on debug at the top of >>>>> arch/powerpc/platforms/mpc52xx/mpc52xx_pci.c and post your kernel >>>>> output. >>>>> >>>>> g. >>>>> >>>>> -- >>>>> Grant Likely, B.Sc., P.Eng. >>>>> Secret Lab Technologies Ltd. >>>>> >>>> >>>> >>>> >>>> -- >>>> >>>> H=E4lsningar/Regards >>>> Tobias Knutsson >>>> >>> >>> >>> >>> -- >>> Grant Likely, B.Sc., P.Eng. >>> Secret Lab Technologies Ltd. >> > > > > -- > > H=E4lsningar/Regards > Tobias Knutsson > --=20 H=E4lsningar/Regards Tobias Knutsson ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: MPC5200 PCI Issues 2009-02-04 16:53 MPC5200 PCI Issues Tobias Knutsson 2009-02-04 17:54 ` Grant Likely @ 2009-02-06 13:34 ` Andre Schwarz 2009-02-06 20:38 ` Tobias Knutsson 1 sibling, 1 reply; 9+ messages in thread From: Andre Schwarz @ 2009-02-06 13:34 UTC (permalink / raw) To: Tobias Knutsson; +Cc: linuxppc-dev Tobias, are you starting with 2.6.28 or are you upgrading ? My system runs very fine with 2.6.27 .... Tobias Knutsson wrote: > I am currently trying to get an MPC5200-based board to run Linux > 2.6.28. Most of the devices are working, however i have some issues > with the PCI-bus. More precisely, the issue is that all of > the cards' IO-regions are mapped to address 0x0. > > In my device tree I have the following: > > pci@f0000d00 { > #interrupt-cells = <1>; > #size-cells = <2>; > #address-cells = <3>; > device_type = "pci"; > compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci"; > reg = <0xf0000d00 0x100>; > interrupt-map-mask = <0xf800 0 0 7>; > interrupt-map = <0xb000 0 0 1 &mpc5200_pic 0 0 3 // MPC5200 > 0xb000 0 0 2 &mpc5200_pic 0 0 3 > 0xb000 0 0 3 &mpc5200_pic 0 0 3 > 0xb000 0 0 4 &mpc5200_pic 0 0 3 > What's this ? Is the MPC5200 interrupting itself ? > 0xb800 0 0 1 &mpc5200_pic 1 1 3 // c64x0 > 0xb800 0 0 2 &mpc5200_pic 1 1 3 > 0xb800 0 0 3 &mpc5200_pic 1 1 3 > 0xb800 0 0 4 &mpc5200_pic 1 1 3 > Have you connected 4 IRQ lines to each c64x device ? > 0xc000 0 0 1 &mpc5200_pic 1 1 3 // c64x1 > 0xc000 0 0 2 &mpc5200_pic 1 1 3 > 0xc000 0 0 3 &mpc5200_pic 1 1 3 > 0xc000 0 0 4 &mpc5200_pic 1 1 3 > > 0xc800 0 0 1 &mpc5200_pic 1 1 3 // c64x2 > 0xc800 0 0 2 &mpc5200_pic 1 1 3 > 0xc800 0 0 3 &mpc5200_pic 1 1 3 > 0xc800 0 0 4 &mpc5200_pic 1 1 3 > > 0xd000 0 0 1 &mpc5200_pic 1 1 3 // c64x3 > 0xd000 0 0 2 &mpc5200_pic 1 1 3 > 0xd000 0 0 3 &mpc5200_pic 1 1 3 > 0xd000 0 0 4 &mpc5200_pic 1 1 3 > > 0xd800 0 0 1 &mpc5200_pic 1 1 3 // c64x4 > 0xd800 0 0 2 &mpc5200_pic 1 1 3 > 0xd800 0 0 3 &mpc5200_pic 1 1 3 > 0xd800 0 0 4 &mpc5200_pic 1 1 3>; > > I'm using an external FPGA and an e1000 NIC connectedt to IRQ2 and IRQ3 : interrupt-map = <0x5800 0 0 1 &mpc5200_pic 1 2 3 0x5000 0 0 1 &mpc5200_pic 1 3 3>; > clock-frequency = <0x1e84800>; //<0>; // From boot loader > interrupts = <2 8 0 2 9 0 2 10 0>; > interrupt-parent = <&mpc5200_pic>; > bus-range = <0 0>; > ranges = <0x02000000 0 0x50000000 0x50000000 0 0x10000000 > 0x01000000 0 0x00000000 0x60000000 0 0x01000000>; > }; > I'm using a 3 liner : ranges = <0x42000000 0 0x80000000 0x80000000 0 0x20000000 0x02000000 0 0xa0000000 0xa0000000 0 0x10000000 0x01000000 0 0x00000000 0xb0000000 0 0x01000000>; > The cards' memory regions are mapped out fine to different addresses > in the 0x50000000-0x60000000 range. However, the IO regions are all mapped > to zero. > > Are you c64x devices responding properly ? Is IO access enabled in the PCI command register ? Are they announcing a reasonable window ? How man KBytes ? > Do you have any idea on what could be wrong or in which direction I > should be looking? > > > Hopefully something is useful to you. regards, Andre MATRIX VISION GmbH, Talstraße 16, DE-71570 Oppenweiler Registergericht: Amtsgericht Stuttgart, HRB 271090 Geschäftsführer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim Reich ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: MPC5200 PCI Issues 2009-02-06 13:34 ` Andre Schwarz @ 2009-02-06 20:38 ` Tobias Knutsson 0 siblings, 0 replies; 9+ messages in thread From: Tobias Knutsson @ 2009-02-06 20:38 UTC (permalink / raw) To: Andre Schwarz; +Cc: linuxppc-dev Hi Andre, I started the development with 2.6.28. Thanks for all of your suggestions but I managed to find the solution today. The problem was that the PCI-cards did not have class specified. Adding a fixup hook to the cards in quirks.c resolved the issue. On Fri, Feb 6, 2009 at 14:34, Andre Schwarz <andre.schwarz@matrix-vision.de> wrote: > Tobias, > > are you starting with 2.6.28 or are you upgrading ? > My system runs very fine with 2.6.27 .... > > Tobias Knutsson wrote: >> >> I am currently trying to get an MPC5200-based board to run Linux >> 2.6.28. Most of the devices are working, however i have some issues >> with the PCI-bus. More precisely, the issue is that all of >> the cards' IO-regions are mapped to address 0x0. >> In my device tree I have the following: >> >> pci@f0000d00 { >> #interrupt-cells =3D <1>; >> #size-cells =3D <2>; >> #address-cells =3D <3>; >> device_type =3D "pci"; >> compatible =3D "fsl,mpc5200b-pci","fsl,mpc5200-pci"; >> reg =3D <0xf0000d00 0x100>; >> interrupt-map-mask =3D <0xf800 0 0 7>; >> interrupt-map =3D <0xb000 0 0 1 &mpc5200_pic 0 0 3 // MPC5= 200 >> 0xb000 0 0 2 &mpc5200_pic 0 0 3 >> 0xb000 0 0 3 &mpc5200_pic 0 0 3 >> 0xb000 0 0 4 &mpc5200_pic 0 0 3 >> > > What's this ? Is the MPC5200 interrupting itself ? No, the PCI-bridge is connected to IRQ0 >> >> 0xb800 0 0 1 &mpc5200_pic 1 1 3 // c64x0 >> 0xb800 0 0 2 &mpc5200_pic 1 1 3 >> 0xb800 0 0 3 &mpc5200_pic 1 1 3 >> 0xb800 0 0 4 &mpc5200_pic 1 1 3 >> > > Have you connected 4 IRQ lines to each c64x device ? No, this is just some copy-paste leftovers that should be trimmed down after some examination of the schematics. >> >> 0xc000 0 0 1 &mpc5200_pic 1 1 3 // c64x1 >> 0xc000 0 0 2 &mpc5200_pic 1 1 3 >> 0xc000 0 0 3 &mpc5200_pic 1 1 3 >> 0xc000 0 0 4 &mpc5200_pic 1 1 3 >> >> 0xc800 0 0 1 &mpc5200_pic 1 1 3 // c64x2 >> 0xc800 0 0 2 &mpc5200_pic 1 1 3 >> 0xc800 0 0 3 &mpc5200_pic 1 1 3 >> 0xc800 0 0 4 &mpc5200_pic 1 1 3 >> >> 0xd000 0 0 1 &mpc5200_pic 1 1 3 // c64x3 >> 0xd000 0 0 2 &mpc5200_pic 1 1 3 >> 0xd000 0 0 3 &mpc5200_pic 1 1 3 >> 0xd000 0 0 4 &mpc5200_pic 1 1 3 >> >> 0xd800 0 0 1 &mpc5200_pic 1 1 3 // c64x4 >> 0xd800 0 0 2 &mpc5200_pic 1 1 3 >> 0xd800 0 0 3 &mpc5200_pic 1 1 3 >> 0xd800 0 0 4 &mpc5200_pic 1 1 3>; >> >> > > I'm using an external FPGA and an e1000 NIC connectedt to IRQ2 and IRQ3 : > > interrupt-map =3D <0x5800 0 0 1 &mpc5200_pic 1 2 3 > 0x5000 0 0 1 &mpc5200_pic = 1 3 > 3>; > > >> clock-frequency =3D <0x1e84800>; //<0>; // From boot load= er >> interrupts =3D <2 8 0 2 9 0 2 10 0>; >> interrupt-parent =3D <&mpc5200_pic>; >> bus-range =3D <0 0>; >> ranges =3D <0x02000000 0 0x50000000 0x50000000 0 0x1000000= 0 >> 0x01000000 0 0x00000000 0x60000000 0 0x01000000>= ; >> }; >> > > I'm using a 3 liner : > > ranges =3D <0x42000000 0 0x80000000 0x80000000 0 0x20000000 > 0x02000000 0 0xa0000000 0xa0000000 0 0x10000000 > 0x01000000 0 0x00000000 0xb0000000 0 0x01000000>; > >> The cards' memory regions are mapped out fine to different addresses >> in the 0x50000000-0x60000000 range. However, the IO regions are all mapp= ed >> to zero. >> >> > > Are you c64x devices responding properly ? Is IO access enabled in the PC= I > command register ? > Are they announcing a reasonable window ? How man KBytes ? >> >> Do you have any idea on what could be wrong or in which direction I >> should be looking? >> >> >> > > Hopefully something is useful to you. > > regards, > Andre > > > MATRIX VISION GmbH, Talstra=DFe 16, DE-71570 Oppenweiler > Registergericht: Amtsgericht Stuttgart, HRB 271090 > Gesch=E4ftsf=FChrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, > Hans-Joachim Reich > --=20 H=E4lsningar/Regards Tobias Knutsson ^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2009-02-06 20:38 UTC | newest] Thread overview: 9+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2009-02-04 16:53 MPC5200 PCI Issues Tobias Knutsson 2009-02-04 17:54 ` Grant Likely 2009-02-05 7:06 ` Tobias Knutsson 2009-02-05 16:44 ` Grant Likely 2009-02-05 20:03 ` Tobias Knutsson 2009-02-06 11:46 ` Tobias Knutsson 2009-02-06 12:39 ` Tobias Knutsson 2009-02-06 13:34 ` Andre Schwarz 2009-02-06 20:38 ` Tobias Knutsson
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).