From: Vijay Nikam <vijay.t.nikam@gmail.com>
To: linuxppc-dev@ozlabs.org
Cc: Scott Wood <scottwood@freescale.com>
Subject: Re: Regarding irq_of_parse_and_map
Date: Tue, 17 Feb 2009 17:11:24 +0530 [thread overview]
Message-ID: <f234e2140902170341y31662e8fla8a8cf87473ed419@mail.gmail.com> (raw)
In-Reply-To: <20090216180857.GA18069@ld0162-tx32.am.freescale.net>
I added the gpio node as follows to mpc8313erdb.dts;
gpio@c00 {
linux,phandle = <c00>;
device_type = "gpio";
compatible = "";
reg = <c00 100>;
interrupts = <4a 8>;
interrupt-parent = <700>;
};
The only thing I need to know what should I write at 'compatible' tag
? ? ? the compatible tag format is "manufacturer,model" the
manufacturer is 'fsl' i.e. I think freescale but the model, as it is
the model number where I can find this model ? ? ? Please let me know
... thanks ...
Also I would like to ask if the above device node is written according
to bindings ... I think it should be right as I referred
'bootingwithout-of.txt' ... but please correct me if I am worng ? ? ?
If yes then I would like to confirm my further action is to compile
with dtc and create dtb and load it on the target and boot the board
... Am I Right ? ? ?
Kindly please acknowledge ... thank you ...
Following is the content of mpc8313erdb.dts to make it sure if it is
in bindings ...
################### DTS ##############################
/* MPC8313E RDB Device Tree Source */
/ {
model = "MPC8313ERDB";
compatible = "mpc83xx";
#address-cells = <1>;
#size-cells = <1>;
cpus {
#cpus = <1>;
#address-cells = <1>;
#size-cells = <0>;
PowerPC,8313@0 {
device_type = "cpu";
reg = <0>;
d-cache-line-size = <20>; // 32 bytes
i-cache-line-size = <20>; // 32 bytes
d-cache-size = <4000>; // L1, 16K
i-cache-size = <4000>; // L1, 16K
timebase-frequency = <0>; // from bootloader
bus-frequency = <0>; // from bootloader
clock-frequency = <0>; // from bootloader
32-bit;
};
};
memory {
device_type = "memory";
reg = <00000000 08000000>; // 128MB at 0
};
nand0 {
device_type = "nand";
compatible = "fsl-nand";
linux,phandle = <301>;
reg = <e2800000 2000>;
/*partitions = "nand0:1m(u-boot)ro,3m(kernel),-(jffs2)";*/
};
soc8313@e0000000 {
#address-cells = <1>;
#size-cells = <1>;
#interrupt-cells = <2>;
device_type = "soc";
ranges = <0 e0000000 00100000>;
reg = <e0000000 00000200>;
bus-frequency = <0>;
wdt@200 {
device_type = "watchdog";
compatible = "mpc83xx_wdt";
reg = <200 100>;
};
i2c@3000 {
device_type = "i2c";
compatible = "fsl-i2c";
reg = <3000 100>;
interrupts = <e 8>;
interrupt-parent = <700>;
dfsrr;
};
i2c@3100 {
device_type = "i2c";
compatible = "fsl-i2c";
reg = <3100 100>;
interrupts = <f 8>;
interrupt-parent = <700>;
dfsrr;
};
spi@7000 {
device_type = "spi";
compatible = "mpc83xx_spi";
reg = <7000 1000>;
interrupts = <10 8>;
interrupt-parent = <700>;
mode = <0>;
};
/* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
usb@23000 {
device_type = "usb";
compatible = "fsl-usb2-dr";
reg = <23000 1000>;
#address-cells = <1>;
#size-cells = <0>;
interrupt-parent = <700>;
interrupts = <26 2>;
phy_type = "utmi_wide";
control_init = <00000280>; // UTMI ext 48 MHz clk
sleep = <b00 00300000>;
};
mdio@24520 {
device_type = "mdio";
compatible = "gianfar";
reg = <24520 20>;
#address-cells = <1>;
#size-cells = <0>;
linux,phandle = <24520>;
ethernet-phy@1 {
linux,phandle = <2452001>;
interrupt-parent = <700>;
interrupts = <13 2>;
reg = <1>;
device_type = "ethernet-phy";
};
ethernet-phy@4 {
linux,phandle = <2452004>;
interrupt-parent = <700>;
interrupts = <14 2>;
reg = <4>;
device_type = "ethernet-phy";
};
};
ethernet@24000 {
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <24000 1000>;
regs_1588 = <24000 24fff>;
address = [ 00 00 00 00 00 00 ];
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <25 8 24 8 23 8>;
interrupt-parent = <700>;
phy-handle = <2452001>;
sleep = <b00 20000000>;
fsl,magic-packet;
};
ethernet@25000 {
#address-cells = <1>;
#size-cells = <0>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <25000 1000>;
regs_1588 = <24000 24fff>;
address = [ 00 00 00 00 00 00 ];
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <22 8 21 8 20 8>;
interrupt-parent = <700>;
phy-handle = <2452004>;
sleep = <b00 10000000>;
fsl,magic-packet;
};
serial@4500 {
device_type = "serial";
compatible = "ns16550";
reg = <4500 100>;
clock-frequency = <0>;
interrupts = <9 8>;
interrupt-parent = <700>;
};
serial@4600 {
device_type = "serial";
compatible = "ns16550";
reg = <4600 100>;
clock-frequency = <0>;
interrupts = <a 8>;
interrupt-parent = <700>;
};
pci@8500 {
interrupt-map-mask = <f800 0 0 7>;
interrupt-map = <
/* IDSEL 0x0E -mini PCI */
7000 0 0 1 700 12 8
7000 0 0 2 700 12 8
7000 0 0 3 700 12 8
7000 0 0 4 700 12 8
/* IDSEL 0x0F - PCI slot */
7800 0 0 1 700 11 8
7800 0 0 2 700 12 8
7800 0 0 3 700 11 8
7800 0 0 4 700 12 8>;
interrupt-parent = <700>;
interrupts = <42 8>;
bus-range = <0 0>;
ranges = <02000000 0 90000000 90000000 0 10000000
42000000 0 80000000 80000000 0 10000000
01000000 0 00000000 e2000000 0 00100000>;
clock-frequency = <3f940aa>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
reg = <8500 100>;
compatible = "83xx";
device_type = "pci";
sleep = <b00 00010000>;
};
/* May need to remove if on a part without crypto engine */
crypto@30000 {
device_type = "crypto";
model = "SEC2";
compatible = "talitos";
reg = <30000 10000>;
interrupts = <b 8>;
interrupt-parent = <700>;
num-channels = <4>;
channel-fifo-len = <18>;
exec-units-mask = <0000007e>;
/* desc mask is for rev2.0,
* we need runtime fixup for >2.0 */
descriptor-types-mask = <01010ebf>;
sleep = <b00 03000000>;
};
/* IPIC
* interrupts cell = <intr #, sense>
* sense values match linux IORESOURCE_IRQ_* defines:
* sense == 8: Level, low assertion
* sense == 2: Edge, high-to-low change
*/
pic@700 {
linux,phandle = <700>;
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <2>;
reg = <700 100>;
built-in;
device_type = "ipic";
};
elbc@5000 {
linux,phandle = <5000>;
device_type = "elbc";
compatible = "fsl-elbc";
reg = <5000 1000>;
interrupts = <4d 8>;
interrupt-parent = <700>;
};
power@b00 {
linux,phandle = <b00>;
device_type = "power";
compatible = "fsl,mpc831x-pmc", "fsl,mpc83xx-pmc";
reg = <b00 100
a00 100>;
interrupts = <50 8>;
interrupt-parent = <700>;
};
timer@500 {
linux,phandle = <500>;
device_type = "timer";
compatible = "fsl,mpc831x-gtm", "fsl,mpc83xx-gtm";
reg = <500 100>;
interrupts = <48 8>;
interrupt-parent = <700>;
};
};
};
###################### END #######################################
Kind Regards,
Vijay Nikam
On 2/16/09, Scott Wood <scottwood@freescale.com> wrote:
> On Mon, Feb 16, 2009 at 05:25:23PM +0530, Vijay Nikam wrote:
> > 2. Also I would like to ask how I can determine the virtual irq using
> > irq_of_parse_and_map (struct device_node *dev, int index) ? ? ?
> >
> > here I am not getting what I should pass *dev and index ? ? ? as in my
> > mpc8313erdb.dts I could not find any node name 'gpio' so I do not know
> > what I can use ...
>
> You'd need to add a gpio node to the device tree. If you do this, be
> sure to follow existing bindings.
>
> >
> > Kindly please acknowledge ... thank you ...
> >
> > Following is the content of mpc8313erdb.dts
>
> That device tree looks very old, as if it came from a BSP rather than
> upstream Linux.
>
> -Scott
>
next prev parent reply other threads:[~2009-02-17 11:41 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-02-16 11:55 Regarding irq_of_parse_and_map Vijay Nikam
2009-02-16 18:08 ` Scott Wood
2009-02-17 11:41 ` Vijay Nikam [this message]
2009-02-17 17:14 ` Scott Wood
2009-02-18 12:01 ` Vijay Nikam
2009-02-18 16:57 ` Scott Wood
2009-02-19 11:51 ` Vijay Nikam
2009-02-19 17:24 ` Jon Loeliger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=f234e2140902170341y31662e8fla8a8cf87473ed419@mail.gmail.com \
--to=vijay.t.nikam@gmail.com \
--cc=linuxppc-dev@ozlabs.org \
--cc=scottwood@freescale.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).