* Re: PPC 32bits and big RAM mapping problem
From: Matt Porter @ 2005-12-01 18:56 UTC (permalink / raw)
To: Rune Torgersen; +Cc: linuxppc-embedded
In-Reply-To: <DCEAAC0833DD314AB0B58112AD99B93B8594B6@ismail.innsys.innovsys.com>
On Thu, Dec 01, 2005 at 12:43:02PM -0600, Rune Torgersen wrote:
> > -----Original Message-----
> > From: Laurent Lagrange
> > Sent: Thursday, December 01, 2005 11:48
> > To: linuxppc-embedded@ozlabs.org
> > Subject: PPC 32bits and big RAM mapping problem
>
> > So I'm under the impression to be cornered in my shoes.
> > Any idea, book, article, prediction would be welcome.
>
> I have 2GB of ram working on my PPC32 board.
>
> You have to change the following in the kernel config:
> Under Advanced Setup:
> Set Maximum Low memory (Set to 0x40000000)
> Set Custom Kernel config address (Set to 0xA0000000)
>
> I do not remember if I had to change anything else.
If you have 2GB you had to have something else. Right now
you have it set to constrict the max lowmem to 1GB. So,
you must have CONFIG_HIGHMEM on as well to utilize the
other 1GB.
To answer the original poster's question: simply enable
CONFIG_HIGHMEM and UP system will have 768MB in lowmem and
the rest in highmem. If there's some constraint on your
application (like many embedded apps) that requires all
2GB in lowmem then configure:
Set Maximum low memory (Set to 0x80000000)
Set custom kernel base address (Set to 0x40000000)
Set custom user task size (Set to 0x40000000)
Don't do this unless highmem won't work for your app. If you
use this approach each process will be limited to 1GB of virtual
memory which may or may not be an OK tradeoff for your app.
-Matt
^ permalink raw reply
* RE: PPC 32bits and big RAM mapping problem
From: Rune Torgersen @ 2005-12-01 18:43 UTC (permalink / raw)
To: Laurent Lagrange; +Cc: linuxppc-embedded
> -----Original Message-----
> From: Laurent Lagrange
> Sent: Thursday, December 01, 2005 11:48
> To: linuxppc-embedded@ozlabs.org
> Subject: PPC 32bits and big RAM mapping problem
> So I'm under the impression to be cornered in my shoes.
> Any idea, book, article, prediction would be welcome.
I have 2GB of ram working on my PPC32 board.
You have to change the following in the kernel config:
Under Advanced Setup:
Set Maximum Low memory (Set to 0x40000000)
Set Custom Kernel config address (Set to 0xA0000000)
I do not remember if I had to change anything else.
^ permalink raw reply
* PPC 32bits and big RAM mapping problem
From: Laurent Lagrange @ 2005-12-01 17:47 UTC (permalink / raw)
To: linuxppc-embedded
Hello,
I have a PPC board with an address width fixed to 32bits, so I can address
4GB.
M M M M M M M
0 0 0 0 0 1 e
0 2 8 c e e f
---------------------------------------------------------------------------
---
| Physical | | PCI | Kernel | Kernel | User |
Peripheral |
| RAM | unused | memory | memory | reserved | memory | mapping
|
| | | | kmalloc | | vmalloc |
|
| ex 512MB | | ex 1GB | ex 512MB | 16MB | | ex 32MB
|
| 2GB max | 1GB max | max ? | | 464MB max |
|
---------------------------------------------------------------------------
---
(0) (1) (2)
00M stand for 0x00000000
(0) kernel_base
(1) vmalloc_start
(2) vmalloc_end
The exemple above shows a classical(?) mapping with a physical RAM of 512MB.
The physical RAM can growth up to 2GB, but if the kernel maps a Kernel
memory
of 2GB, there is no more place for the other items. The 4GB are eated.
Even with only 512MB of RAM, the kernel can't fully vmalloc it for user.
I know that the kernel and drivers kmalloc in Kernel memory which has the
full
space but when the users wants more RAM, it is for vmallocations.
Now when the physical RAM increases, the User memory is reduced for vmalloc.
And I don't talk about Peripheral mappings which also reduce the User
memory.
So I'm under the impression to be cornered in my shoes.
Any idea, book, article, prediction would be welcome.
Thanks
Laurent
^ permalink raw reply
* Re: MPC8555 8280/8270 USB host support
From: Wolfgang Denk @ 2005-12-01 17:37 UTC (permalink / raw)
To: Nathael PAJANI; +Cc: linuxppc-embedded
In-Reply-To: <438F198F.9020606@cpe.fr>
In message <438F198F.9020606@cpe.fr> you wrote:
>
> If u-boot is the boot loader of your board (the stuff running on it
> --before-- we see this:
>
> loaded at: 00400000 005153B4
> board data at: 00513130 00513334
> relocated to: 00405090 00405294
> zimage at: 00405A85 00512099
> avail ram: 00516000 08000000
If U-Boot is your boot load, *and* you see this, than you made some
serious mistake. U-Boot is supposed to boot the "uImage" images,
which do not issue such messages.
Best regards,
Wolfgang Denk
--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd@denx.de
The shortest unit of time in the multiverse is the News York Second,
defined as the period of time between the traffic lights turning
green and the cab behind you honking.
- Terry Pratchett, _Lords and Ladies_
^ permalink raw reply
* RE: RE: linuxppc-embedded help needed:kernel access of bad area
From: Rune Torgersen @ 2005-12-01 16:45 UTC (permalink / raw)
To: zengshuai; +Cc: linuxppc-embedded
> -----Original Message-----
> From: zengshuai@sogou.com
> Sent: Thursday, December 01, 2005 00:52
> #define BCSRADDR 0x04500000
This address is wrong.
It's the address the manual gives, but the bootloadre usually moves it
because it interferes with the SDRAM when running Linux.
Check the bootloader, or even better, if you know which ChipSelect the
BCSR is on, read the BRn register and use that address.
sort of like:
bcsr_addr =3D cpm2_immr->im_memctl.memc_br1 & 0xffff8000; // BCSR is on
CS1 on MPC8266ADS board
^ permalink raw reply
* Re: MPC8555 8280/8270 USB host support
From: Nathael PAJANI @ 2005-12-01 15:41 UTC (permalink / raw)
To: linuxppc-embedded
Hi
>
>>
>>Don't you think u-boot should take care of clock setup
>>i.e. as much as possible of all board dependent stuff ?
>>
>>
>I think you're right, but then it was easier to make all these setups
>in the driver itself.
>
If u-boot is the boot loader of your board (the stuff running on it
--before-- we see this:
loaded at: 00400000 005153B4
board data at: 00513130 00513334
relocated to: 00405090 00405294
zimage at: 00405A85 00512099
avail ram: 00516000 08000000
Linux/PPC load: rw console=ttyS0 root=/dev/nfs ip=on
Uncompressing Linux...done)
Then I would say NO
If u-boot is this exact stuff (the files in arch/ppc/boot/simple/...
misc-embedded.c for example)
then, yes, this is somehow better.
But (tell me if I'm wrong) this is not really Linux code, and this
should be done by Linux.
What I think should be good also is the platform files
(arch/ppc/platforms/....) for this is the place where all the board
dependant stuff stays.
Maybe I'm completely mistaken.
Feel free to tell me (and explain please !)
Have fun.
^ permalink raw reply
* Re: MPC8555 8280/8270 USB host support
From: Wolfgang Denk @ 2005-12-01 15:29 UTC (permalink / raw)
To: Hans Schillstrom; +Cc: 'linuxppc-embedded@ozlabs.org'
In-Reply-To: <1133439981.8518.237.camel@hawk.pwav.net>
In message <1133439981.8518.237.camel@hawk.pwav.net> you wrote:
>
> Don't you think u-boot should take care of clock setup
> i.e. as much as possible of all board dependent stuff ?
No, it should not. A river should not make any assumptions about the
state of the hardware, but initialize everything it needs for correct
operation itself.
Best regards,
Wolfgang Denk
--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd@denx.de
Save yourself! Reboot in 5 seconds!
^ permalink raw reply
* Re: Linux hangs while Uncompressing
From: Wolfgang Denk @ 2005-12-01 15:27 UTC (permalink / raw)
To: pritha.bhattacharya; +Cc: linuxppc-embedded
In-Reply-To: <OF0098DF7F.857DE409-ON652570CA.001AA3F7-652570CA.0036DB32@tcs.com>
In message <OF0098DF7F.857DE409-ON652570CA.001AA3F7-652570CA.0036DB32@tcs.com> you wrote:
>
> I have RAM version of U-Boot which is running on a board similar to
> MPC8260. My memory map isas follows:
Your mode of operation is unsupported.
You either ignored to read the FAQ, or it's content:
http://www.denx.de/wiki/view/DULG/CanUBootBeConfiguredSuchThatItCanBeStartedInRAM
> Staring address Device Size Memory
> controller and CS
...
0F00 0000 CPU internal registers
3000 0000 SDRAM
...
Your memory map is bogus.
You either ignored to read the FAQ, or it's content:
http://www.denx.de/wiki/view/PPCEmbedded/Kernel#Section_10.2.
...
> Verifying Checksum ... OK
> Uncompressing Kernel Image ...
>
> The system hangs here and is not able to uncompress the kernel any
> further. I have checked in the FAQs provided in the denx's site, but could
> not find anything similar to my case.
You either ignored to read the FAQ, or it's content:
http://www.denx.de/wiki/view/DULG/LinuxUncompressingError
I think you should go back and read the existing documentation, and
follow the advice it contains.
If you continue to ignore what's written in the FAQ's you would
probably also ignore any answeres to your postings here.
Best regards,
Wolfgang Denk
--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd@denx.de
This is an unauthorized cybernetic announcement.
^ permalink raw reply
* Mailing list
From: Nathael PAJANI @ 2005-12-01 15:18 UTC (permalink / raw)
To: linuxppc-embedded
Hi all
For the sake of the mailing list (and my own sake) do you know of a
mailer tool which handles the "in-reply-to" field ?
And of course, how should the field be set with this particular tool.
Thanks a lot.
^ permalink raw reply
* Re: [PATCH] ppc32: 8xx board-specific platform stuff for fs_enet
From: Kumar Gala @ 2005-12-01 15:13 UTC (permalink / raw)
To: Marcelo Tosatti; +Cc: linuxppc-embedded list, Paul Mackerras
In-Reply-To: <20051201121711.GA4105@dmt.cnet>
On Dec 1, 2005, at 6:17 AM, Marcelo Tosatti wrote:
> On Wed, Nov 30, 2005 at 01:08:31AM -0600, Kumar Gala wrote:
>>> Hi Kumar,
>>>
>>> I dont really know the policy for driver placement, but it seems
>>> that
>>> it works on a case by case basis.
>>>
>>> The files in arch/ppc/8xx_io/ (which is what I think you refer to as
>>> candidates for drivers/), are:
>>
>> We have been slowly working on moving drivers out of arch/ppc and
>> into drivers/ so that subsystem maintainers could get proper review
>> of them.
>>
>>> 1) commproc.c
>>> Basic API for dpram access. Core code.
>>>
>>> 2) micropatch.c
>>> microcode update code/data. Core code.
>>
>> Well #1 & #2 aren't what I would call drivers at all. I would
>> consider them syslib/ candidates. Hopefully, someone will
>
> Move them there? Yeah... We can add that to the 8xx TODO list
> if its interesting.
I would just wait and move them to arch/powerpc/sysdev whenever 8xx
moves over to arch/powerpc. No reason to move the files twice.
>>> 3) cs4218.h
>>> 4) cs4218_tdm.c
>>>
>>> cs4218 does not compile at the moment due to syntatical problems,
>>> I've fixed them up and the driver compiles, but I don't know
>>> if it works (patch attached).
>>>
>>> I would not be surprised if the driver has been broken since
>>> long time ago.
>>>
>>> Does anyone have hardware to test it? Dan?
>>>
>>> Otherwise we should remove it from the tree, since its unmaintained
>>> and unused.
>>
>> If its still good, I would guessing /drivers/audio or snd, but
>> neither seem to exist. I wondering where sound card drivers live
>> these days.
>
> snd/ I think... Someone needs to test the driver. I think we should
> just
> fixup the syntactical problems and mark it as BROKEN until someone
> (Dan?)
> confirms it works.
Agreed.
>>> 5) enet.c
>>> 6) fec.c
>>>
>>> The ENET/FEC network drivers are obseleted by fs_enet.
>>>
>>> However there are some PHY descriptions in fec.c which are missing
>>> from
>>> fs_enet - we'd better make sure to have them all in the new driver
>>> before removing the old one.
>>
>> Agreed.
>>
>>> Aris, would you mind looking into this?
>>>
>>> Once we have that we can set a deadline at Documentation/feature-
>>> removal.txt
>>> if desired.
>>>
>>> Other than those there are no 8xx drivers in arch/ppc/ AFAIK.
>>>
>>> <cs42.patch>
>>
>> Good deal. Are we really removing anything (except maybe cs4218)?
>
> FEC certainly and cs4218 seems like a candidate.
Well cs4218 depends on Dan's feedback. As far as FEC, I see that we
replaced it with something else. So we should feel free to remove it
from 8xx_io as long as we feel that the new driver will work for
people and update the in kernel platforms for it.
- kumar
^ permalink raw reply
* Re: [PATCH] ppc32: 8xx board-specific platform stuff for fs_enet
From: Dan Malek @ 2005-12-01 14:15 UTC (permalink / raw)
To: Marcelo Tosatti; +Cc: linuxppc-embedded list, Paul Mackerras
In-Reply-To: <20051201121711.GA4105@dmt.cnet>
On Dec 1, 2005, at 7:17 AM, Marcelo Tosatti wrote:
> snd/ I think... Someone needs to test the driver. I think we should
> just
> fixup the syntactical problems and mark it as BROKEN until someone
> (Dan?)
> confirms it works.
Since I'm probably the only one left in the world with this
hardware, it probably doesn't make sense to keep it around.
I know people have used it in the past as an example of how
to program the TDM on the 8xx, but it's not necessary to keep
it around for that reason.
Thanks.
-- Dan
^ permalink raw reply
* Re: MPC8555 8280/8270 USB host support
From: Mike Rapoport @ 2005-12-01 13:55 UTC (permalink / raw)
To: Hans Schillstrom; +Cc: 'linuxppc-embedded@ozlabs.org'
In-Reply-To: <1133439981.8518.237.camel@hawk.pwav.net>
Hans Schillstrom wrote:
>Hi Mike
>I've made some modifications due to the difference between mpc8272 and
>mpc8270. MPC8272 use SCC3 and MPC8270 use SCC4.
>Added some more clock configuration options ...
>
>
Thanks a lot.
I've added your patch as is to the SF page.
>
>Don't you think u-boot should take care of clock setup
>i.e. as much as possible of all board dependent stuff ?
>
>
I think you're right, but then it was easier to make all these setups in
the driver itself.
>
>Regards
>Hans Schillstrom
>
>
>
--
Sincerely yours,
Mike Rapoport
^ permalink raw reply
* [PATCH] ppc32: Add TQM85xx (8540/8541/8555/8560) board support
From: Stefan Roese @ 2005-12-01 13:30 UTC (permalink / raw)
To: linuxppc-embedded
In-Reply-To: <15EF7506-D65A-4FD0-9042-A5133D8B7C65@kernel.crashing.org>
[-- Attachment #1: Type: text/plain, Size: 187 bytes --]
This patch adds support for the TQ Components TQM85xx modules. Currently the
modules TQM8540/8541/8555/8560 are supported.
Signed-off-by: Stefan Roese <sr@denx.de>
Best regards,
Stefan
[-- Attachment #2: add-tqm85xx-board-support-2.patch --]
[-- Type: text/x-diff, Size: 100665 bytes --]
[PATCH] ppc32: Add TQM85xx (8540/8541/8555/8560) board support
This patch adds support for the TQ Components TQM85xx modules. Currently the
modules TQM8540/8541/8555/8560 are supported.
Signed-off-by: Stefan Roese <sr@denx.de>
---
commit 810e94e4183b1bf0a619990d3bccec86e4836ee0
tree 94ce0c00b106030ac0226b3fe0786f1041b31805
parent 5876e88c46890388a876d33ea63946465c2bc190
author Stefan Roese <sr@denx.de> Wed, 30 Nov 2005 18:07:24 +0100
committer Stefan Roese <sr@denx.de> Wed, 30 Nov 2005 18:07:24 +0100
arch/ppc/configs/TQM8540_defconfig | 973 +++++++++++++++++++++++++++++++++++
arch/ppc/configs/TQM8541_defconfig | 986 ++++++++++++++++++++++++++++++++++++
arch/ppc/configs/TQM8555_defconfig | 983 ++++++++++++++++++++++++++++++++++++
arch/ppc/configs/TQM8560_defconfig | 992 ++++++++++++++++++++++++++++++++++++
arch/ppc/platforms/85xx/Kconfig | 28 +
arch/ppc/platforms/85xx/Makefile | 4
arch/ppc/platforms/85xx/tqm85xx.c | 419 +++++++++++++++
arch/ppc/platforms/85xx/tqm85xx.h | 56 ++
include/asm-ppc/mpc85xx.h | 4
9 files changed, 4441 insertions(+), 4 deletions(-)
diff --git a/arch/ppc/configs/TQM8540_defconfig b/arch/ppc/configs/TQM8540_defconfig
new file mode 100644
index 0000000..99bf3b7
--- /dev/null
+++ b/arch/ppc/configs/TQM8540_defconfig
@@ -0,0 +1,973 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.15-rc2
+# Fri Nov 25 17:26:50 2005
+#
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_PPC=y
+CONFIG_PPC32=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_CLEAN_COMPILE=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+CONFIG_SYSCTL=y
+# CONFIG_AUDIT is not set
+# CONFIG_HOTPLUG is not set
+CONFIG_KOBJECT_UEVENT=y
+# CONFIG_IKCONFIG is not set
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_EMBEDDED=y
+# CONFIG_KALLSYMS is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+# CONFIG_EPOLL is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SHMEM=y
+CONFIG_CC_ALIGN_FUNCTIONS=0
+CONFIG_CC_ALIGN_LABELS=0
+CONFIG_CC_ALIGN_LOOPS=0
+CONFIG_CC_ALIGN_JUMPS=0
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+
+#
+# Loadable module support
+#
+# CONFIG_MODULES is not set
+
+#
+# Block layer
+#
+# CONFIG_LBD is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# Processor
+#
+# CONFIG_6xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_POWER3 is not set
+# CONFIG_POWER4 is not set
+# CONFIG_8xx is not set
+# CONFIG_E200 is not set
+CONFIG_E500=y
+CONFIG_BOOKE=y
+CONFIG_FSL_BOOKE=y
+# CONFIG_PHYS_64BIT is not set
+CONFIG_SPE=y
+CONFIG_MATH_EMULATION=y
+# CONFIG_KEXEC is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_WANT_EARLY_SERIAL is not set
+CONFIG_PPC_GEN550=y
+CONFIG_85xx=y
+CONFIG_PPC_INDIRECT_PCI_BE=y
+
+#
+# Freescale 85xx options
+#
+# CONFIG_MPC8540_ADS is not set
+# CONFIG_MPC8548_CDS is not set
+# CONFIG_MPC8555_CDS is not set
+# CONFIG_MPC8560_ADS is not set
+# CONFIG_SBC8560 is not set
+# CONFIG_STX_GP3 is not set
+CONFIG_TQM8540=y
+# CONFIG_TQM8541 is not set
+# CONFIG_TQM8555 is not set
+# CONFIG_TQM8560 is not set
+CONFIG_MPC8540=y
+
+#
+# Platform options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+# CONFIG_SOFTWARE_SUSPEND is not set
+CONFIG_SECCOMP=y
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_PPC_I8259=y
+CONFIG_PPC_INDIRECT_PCI=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+# CONFIG_PCI_LEGACY_PROC is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+# CONFIG_RAPIDIO is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_BOOT_LOAD=0x00800000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_BIC=y
+# CONFIG_IPV6 is not set
+# CONFIG_NETFILTER is not set
+
+#
+# DCCP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_DCCP is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_NET_DIVERT is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_IEEE80211 is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
+
+#
+# Memory Technology Devices (MTD)
+#
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_AMDSTD_RETRY=0
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_TQM85xx=y
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLKMTD is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+
+#
+# NAND Flash Device Drivers
+#
+# CONFIG_MTD_NAND is not set
+
+#
+# OneNAND Flash Device Drivers
+#
+# CONFIG_MTD_ONENAND is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=32768
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+
+#
+# ATA/ATAPI/MFM/RLL support
+#
+CONFIG_IDE=y
+CONFIG_BLK_DEV_IDE=y
+
+#
+# Please see Documentation/ide.txt for help/info on IDE drives
+#
+# CONFIG_BLK_DEV_IDE_SATA is not set
+CONFIG_BLK_DEV_IDEDISK=y
+# CONFIG_IDEDISK_MULTI_MODE is not set
+# CONFIG_BLK_DEV_IDECD is not set
+# CONFIG_BLK_DEV_IDETAPE is not set
+# CONFIG_BLK_DEV_IDEFLOPPY is not set
+# CONFIG_IDE_TASK_IOCTL is not set
+
+#
+# IDE chipset support/bugfixes
+#
+CONFIG_IDE_GENERIC=y
+CONFIG_BLK_DEV_IDEPCI=y
+CONFIG_IDEPCI_SHARE_IRQ=y
+# CONFIG_BLK_DEV_OFFBOARD is not set
+CONFIG_BLK_DEV_GENERIC=y
+# CONFIG_BLK_DEV_OPTI621 is not set
+# CONFIG_BLK_DEV_SL82C105 is not set
+CONFIG_BLK_DEV_IDEDMA_PCI=y
+# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
+CONFIG_IDEDMA_PCI_AUTO=y
+# CONFIG_IDEDMA_ONLYDISK is not set
+# CONFIG_BLK_DEV_AEC62XX is not set
+# CONFIG_BLK_DEV_ALI15X3 is not set
+# CONFIG_BLK_DEV_AMD74XX is not set
+# CONFIG_BLK_DEV_CMD64X is not set
+# CONFIG_BLK_DEV_TRIFLEX is not set
+# CONFIG_BLK_DEV_CY82C693 is not set
+# CONFIG_BLK_DEV_CS5520 is not set
+# CONFIG_BLK_DEV_CS5530 is not set
+# CONFIG_BLK_DEV_HPT34X is not set
+# CONFIG_BLK_DEV_HPT366 is not set
+# CONFIG_BLK_DEV_SC1200 is not set
+# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT821X is not set
+# CONFIG_BLK_DEV_NS87415 is not set
+# CONFIG_BLK_DEV_PDC202XX_OLD is not set
+# CONFIG_BLK_DEV_PDC202XX_NEW is not set
+# CONFIG_BLK_DEV_SVWKS is not set
+# CONFIG_BLK_DEV_SIIMAGE is not set
+# CONFIG_BLK_DEV_SLC90E66 is not set
+# CONFIG_BLK_DEV_TRM290 is not set
+CONFIG_BLK_DEV_VIA82CXXX=y
+# CONFIG_IDE_ARM is not set
+CONFIG_BLK_DEV_IDEDMA=y
+# CONFIG_IDEDMA_IVB is not set
+CONFIG_IDEDMA_AUTO=y
+# CONFIG_BLK_DEV_HD is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Fusion MPT device support
+#
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_IEEE1394 is not set
+
+#
+# I2O device support
+#
+# CONFIG_I2O is not set
+
+#
+# Macintosh device drivers
+#
+# CONFIG_WINDFARM is not set
+
+#
+# Network device support
+#
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+
+#
+# ARCnet devices
+#
+# CONFIG_ARCNET is not set
+
+#
+# PHY device support
+#
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+# CONFIG_NET_VENDOR_3COM is not set
+
+#
+# Tulip family network device support
+#
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+CONFIG_NET_PCI=y
+# CONFIG_PCNET32 is not set
+# CONFIG_AMD8111_ETH is not set
+# CONFIG_ADAPTEC_STARFIRE is not set
+# CONFIG_B44 is not set
+# CONFIG_FORCEDETH is not set
+# CONFIG_DGRS is not set
+# CONFIG_EEPRO100 is not set
+CONFIG_E100=y
+# CONFIG_FEALNX is not set
+# CONFIG_NATSEMI is not set
+# CONFIG_NE2K_PCI is not set
+# CONFIG_8139CP is not set
+# CONFIG_8139TOO is not set
+# CONFIG_SIS900 is not set
+# CONFIG_EPIC100 is not set
+# CONFIG_SUNDANCE is not set
+# CONFIG_TLAN is not set
+# CONFIG_VIA_RHINE is not set
+
+#
+# Ethernet (1000 Mbit)
+#
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SK98LIN is not set
+# CONFIG_VIA_VELOCITY is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+CONFIG_GIANFAR=y
+CONFIG_GFAR_NAPI=y
+
+#
+# Ethernet (10000 Mbit)
+#
+# CONFIG_CHELSIO_T1 is not set
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+
+#
+# Token Ring devices
+#
+# CONFIG_TR is not set
+
+#
+# Wireless LAN (non-hamradio)
+#
+# CONFIG_NET_RADIO is not set
+
+#
+# Wan interfaces
+#
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN is not set
+
+#
+# Telephony Support
+#
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_TSDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+# CONFIG_SERIAL_8250_EXTENDED is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+
+#
+# Watchdog Cards
+#
+# CONFIG_WATCHDOG is not set
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+
+#
+# Ftape, the floppy tape device driver
+#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+# CONFIG_TELCLOCK is not set
+
+#
+# I2C support
+#
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+# CONFIG_I2C_ALI1535 is not set
+# CONFIG_I2C_ALI1563 is not set
+# CONFIG_I2C_ALI15X3 is not set
+# CONFIG_I2C_AMD756 is not set
+# CONFIG_I2C_AMD8111 is not set
+# CONFIG_I2C_I801 is not set
+# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_PIIX4 is not set
+CONFIG_I2C_MPC=y
+# CONFIG_I2C_NFORCE2 is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_PROSAVAGE is not set
+# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_SCx200_ACB is not set
+# CONFIG_I2C_SIS5595 is not set
+# CONFIG_I2C_SIS630 is not set
+# CONFIG_I2C_SIS96X is not set
+# CONFIG_I2C_VIA is not set
+# CONFIG_I2C_VIAPRO is not set
+# CONFIG_I2C_VOODOO3 is not set
+# CONFIG_I2C_PCA_ISA is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+CONFIG_SENSORS_DS1337=y
+# CONFIG_SENSORS_DS1374 is not set
+# CONFIG_SENSORS_EEPROM is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_RTC8564 is not set
+# CONFIG_SENSORS_M41T00 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_RTC_X1205_I2C is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Hardware Monitoring support
+#
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_ADM1021 is not set
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ASB100 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_FSCHER is not set
+# CONFIG_SENSORS_FSCPOS is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+CONFIG_SENSORS_LM75=y
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_SIS5595 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_VIA686A is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+CONFIG_HWMON_DEBUG_CHIP=y
+
+#
+# Misc devices
+#
+
+#
+# Multimedia Capabilities Port drivers
+#
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+# CONFIG_DVB is not set
+
+#
+# Graphics support
+#
+# CONFIG_FB is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+
+#
+# USB support
+#
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+# CONFIG_USB is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+
+#
+# MMC/SD Card support
+#
+# CONFIG_MMC is not set
+
+#
+# InfiniBand support
+#
+# CONFIG_INFINIBAND is not set
+
+#
+# SN Devices
+#
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_RELAYFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+# CONFIG_NFS_V3 is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+# CONFIG_9P_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+# CONFIG_MSDOS_PARTITION is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+
+#
+# Native Language Support
+#
+# CONFIG_NLS is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+CONFIG_CRC32=y
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+# CONFIG_DEBUG_KERNEL is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_SERIAL_TEXT_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+# CONFIG_CRYPTO is not set
+
+#
+# Hardware crypto devices
+#
diff --git a/arch/ppc/configs/TQM8541_defconfig b/arch/ppc/configs/TQM8541_defconfig
new file mode 100644
index 0000000..0ff5669
--- /dev/null
+++ b/arch/ppc/configs/TQM8541_defconfig
@@ -0,0 +1,986 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.15-rc2
+# Wed Nov 30 13:36:28 2005
+#
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_PPC=y
+CONFIG_PPC32=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_CLEAN_COMPILE=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+CONFIG_SYSCTL=y
+# CONFIG_AUDIT is not set
+# CONFIG_HOTPLUG is not set
+CONFIG_KOBJECT_UEVENT=y
+# CONFIG_IKCONFIG is not set
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_EMBEDDED=y
+# CONFIG_KALLSYMS is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+# CONFIG_EPOLL is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SHMEM=y
+CONFIG_CC_ALIGN_FUNCTIONS=0
+CONFIG_CC_ALIGN_LABELS=0
+CONFIG_CC_ALIGN_LOOPS=0
+CONFIG_CC_ALIGN_JUMPS=0
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+
+#
+# Loadable module support
+#
+# CONFIG_MODULES is not set
+
+#
+# Block layer
+#
+# CONFIG_LBD is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# Processor
+#
+# CONFIG_6xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_POWER3 is not set
+# CONFIG_POWER4 is not set
+# CONFIG_8xx is not set
+# CONFIG_E200 is not set
+CONFIG_E500=y
+CONFIG_BOOKE=y
+CONFIG_FSL_BOOKE=y
+# CONFIG_PHYS_64BIT is not set
+CONFIG_SPE=y
+CONFIG_MATH_EMULATION=y
+# CONFIG_KEXEC is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_WANT_EARLY_SERIAL is not set
+CONFIG_PPC_GEN550=y
+CONFIG_85xx=y
+CONFIG_PPC_INDIRECT_PCI_BE=y
+
+#
+# Freescale 85xx options
+#
+# CONFIG_MPC8540_ADS is not set
+# CONFIG_MPC8548_CDS is not set
+# CONFIG_MPC8555_CDS is not set
+# CONFIG_MPC8560_ADS is not set
+# CONFIG_SBC8560 is not set
+# CONFIG_STX_GP3 is not set
+# CONFIG_TQM8540 is not set
+CONFIG_TQM8541=y
+# CONFIG_TQM8555 is not set
+# CONFIG_TQM8560 is not set
+CONFIG_MPC8555=y
+
+#
+# Platform options
+#
+CONFIG_CPM2=y
+# CONFIG_PC_KEYBOARD is not set
+# CONFIG_HIGHMEM is not set
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+# CONFIG_SOFTWARE_SUSPEND is not set
+CONFIG_SECCOMP=y
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_PPC_I8259=y
+CONFIG_PPC_INDIRECT_PCI=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+# CONFIG_PCI_LEGACY_PROC is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_BOOT_LOAD=0x00800000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_BIC=y
+# CONFIG_IPV6 is not set
+# CONFIG_NETFILTER is not set
+
+#
+# DCCP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_DCCP is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_NET_DIVERT is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_IEEE80211 is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
+
+#
+# Memory Technology Devices (MTD)
+#
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_AMDSTD_RETRY=0
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_TQM85xx=y
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLKMTD is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+
+#
+# NAND Flash Device Drivers
+#
+# CONFIG_MTD_NAND is not set
+
+#
+# OneNAND Flash Device Drivers
+#
+# CONFIG_MTD_ONENAND is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=32768
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+
+#
+# ATA/ATAPI/MFM/RLL support
+#
+CONFIG_IDE=y
+CONFIG_BLK_DEV_IDE=y
+
+#
+# Please see Documentation/ide.txt for help/info on IDE drives
+#
+# CONFIG_BLK_DEV_IDE_SATA is not set
+CONFIG_BLK_DEV_IDEDISK=y
+# CONFIG_IDEDISK_MULTI_MODE is not set
+# CONFIG_BLK_DEV_IDECD is not set
+# CONFIG_BLK_DEV_IDETAPE is not set
+# CONFIG_BLK_DEV_IDEFLOPPY is not set
+# CONFIG_IDE_TASK_IOCTL is not set
+
+#
+# IDE chipset support/bugfixes
+#
+CONFIG_IDE_GENERIC=y
+CONFIG_BLK_DEV_IDEPCI=y
+CONFIG_IDEPCI_SHARE_IRQ=y
+# CONFIG_BLK_DEV_OFFBOARD is not set
+CONFIG_BLK_DEV_GENERIC=y
+# CONFIG_BLK_DEV_OPTI621 is not set
+# CONFIG_BLK_DEV_SL82C105 is not set
+CONFIG_BLK_DEV_IDEDMA_PCI=y
+# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
+CONFIG_IDEDMA_PCI_AUTO=y
+# CONFIG_IDEDMA_ONLYDISK is not set
+# CONFIG_BLK_DEV_AEC62XX is not set
+# CONFIG_BLK_DEV_ALI15X3 is not set
+# CONFIG_BLK_DEV_AMD74XX is not set
+# CONFIG_BLK_DEV_CMD64X is not set
+# CONFIG_BLK_DEV_TRIFLEX is not set
+# CONFIG_BLK_DEV_CY82C693 is not set
+# CONFIG_BLK_DEV_CS5520 is not set
+# CONFIG_BLK_DEV_CS5530 is not set
+# CONFIG_BLK_DEV_HPT34X is not set
+# CONFIG_BLK_DEV_HPT366 is not set
+# CONFIG_BLK_DEV_SC1200 is not set
+# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT821X is not set
+# CONFIG_BLK_DEV_NS87415 is not set
+# CONFIG_BLK_DEV_PDC202XX_OLD is not set
+# CONFIG_BLK_DEV_PDC202XX_NEW is not set
+# CONFIG_BLK_DEV_SVWKS is not set
+# CONFIG_BLK_DEV_SIIMAGE is not set
+# CONFIG_BLK_DEV_SLC90E66 is not set
+# CONFIG_BLK_DEV_TRM290 is not set
+CONFIG_BLK_DEV_VIA82CXXX=y
+# CONFIG_IDE_ARM is not set
+CONFIG_BLK_DEV_IDEDMA=y
+# CONFIG_IDEDMA_IVB is not set
+CONFIG_IDEDMA_AUTO=y
+# CONFIG_BLK_DEV_HD is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Fusion MPT device support
+#
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_IEEE1394 is not set
+
+#
+# I2O device support
+#
+# CONFIG_I2O is not set
+
+#
+# Macintosh device drivers
+#
+# CONFIG_WINDFARM is not set
+
+#
+# Network device support
+#
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+
+#
+# ARCnet devices
+#
+# CONFIG_ARCNET is not set
+
+#
+# PHY device support
+#
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+# CONFIG_NET_VENDOR_3COM is not set
+
+#
+# Tulip family network device support
+#
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+CONFIG_NET_PCI=y
+# CONFIG_PCNET32 is not set
+# CONFIG_AMD8111_ETH is not set
+# CONFIG_ADAPTEC_STARFIRE is not set
+# CONFIG_B44 is not set
+# CONFIG_FORCEDETH is not set
+# CONFIG_DGRS is not set
+# CONFIG_EEPRO100 is not set
+CONFIG_E100=y
+# CONFIG_FEALNX is not set
+# CONFIG_NATSEMI is not set
+# CONFIG_NE2K_PCI is not set
+# CONFIG_8139CP is not set
+# CONFIG_8139TOO is not set
+# CONFIG_SIS900 is not set
+# CONFIG_EPIC100 is not set
+# CONFIG_SUNDANCE is not set
+# CONFIG_TLAN is not set
+# CONFIG_VIA_RHINE is not set
+# CONFIG_FS_ENET is not set
+
+#
+# Ethernet (1000 Mbit)
+#
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SK98LIN is not set
+# CONFIG_VIA_VELOCITY is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+CONFIG_GIANFAR=y
+CONFIG_GFAR_NAPI=y
+
+#
+# Ethernet (10000 Mbit)
+#
+# CONFIG_CHELSIO_T1 is not set
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+
+#
+# Token Ring devices
+#
+# CONFIG_TR is not set
+
+#
+# Wireless LAN (non-hamradio)
+#
+# CONFIG_NET_RADIO is not set
+
+#
+# Wan interfaces
+#
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN is not set
+
+#
+# Telephony Support
+#
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_TSDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+# CONFIG_SERIAL_8250_EXTENDED is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_CPM is not set
+# CONFIG_SERIAL_JSM is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+
+#
+# Watchdog Cards
+#
+# CONFIG_WATCHDOG is not set
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+
+#
+# Ftape, the floppy tape device driver
+#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+# CONFIG_TELCLOCK is not set
+
+#
+# I2C support
+#
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+# CONFIG_I2C_ALI1535 is not set
+# CONFIG_I2C_ALI1563 is not set
+# CONFIG_I2C_ALI15X3 is not set
+# CONFIG_I2C_AMD756 is not set
+# CONFIG_I2C_AMD8111 is not set
+# CONFIG_I2C_I801 is not set
+# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_PIIX4 is not set
+CONFIG_I2C_MPC=y
+# CONFIG_I2C_MPC8260 is not set
+# CONFIG_I2C_NFORCE2 is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_PROSAVAGE is not set
+# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_SCx200_ACB is not set
+# CONFIG_I2C_SIS5595 is not set
+# CONFIG_I2C_SIS630 is not set
+# CONFIG_I2C_SIS96X is not set
+# CONFIG_I2C_VIA is not set
+# CONFIG_I2C_VIAPRO is not set
+# CONFIG_I2C_VOODOO3 is not set
+# CONFIG_I2C_PCA_ISA is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+CONFIG_SENSORS_DS1337=y
+# CONFIG_SENSORS_DS1374 is not set
+# CONFIG_SENSORS_EEPROM is not set
+# CONFIG_SENSORS_MAX6900 is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCF8563 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_RTC8564 is not set
+# CONFIG_SENSORS_M41T00 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_RTC_X1205_I2C is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Hardware Monitoring support
+#
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_ADM1021 is not set
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ASB100 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_FSCHER is not set
+# CONFIG_SENSORS_FSCPOS is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+CONFIG_SENSORS_LM75=y
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_SIS5595 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_VIA686A is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+CONFIG_HWMON_DEBUG_CHIP=y
+
+#
+# Misc devices
+#
+
+#
+# Multimedia Capabilities Port drivers
+#
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+# CONFIG_DVB is not set
+
+#
+# Graphics support
+#
+# CONFIG_FB is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+
+#
+# USB support
+#
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+# CONFIG_USB is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+
+#
+# MMC/SD Card support
+#
+# CONFIG_MMC is not set
+
+#
+# InfiniBand support
+#
+# CONFIG_INFINIBAND is not set
+
+#
+# SN Devices
+#
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_RELAYFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+# CONFIG_NFS_V3 is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+# CONFIG_9P_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+# CONFIG_MSDOS_PARTITION is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+
+#
+# Native Language Support
+#
+# CONFIG_NLS is not set
+# CONFIG_SCC_ENET is not set
+# CONFIG_FEC_ENET is not set
+
+#
+# CPM2 Options
+#
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+CONFIG_CRC32=y
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+# CONFIG_DEBUG_KERNEL is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_KGDB_CONSOLE is not set
+# CONFIG_SERIAL_TEXT_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+# CONFIG_CRYPTO is not set
+
+#
+# Hardware crypto devices
+#
diff --git a/arch/ppc/configs/TQM8555_defconfig b/arch/ppc/configs/TQM8555_defconfig
new file mode 100644
index 0000000..730b3db
--- /dev/null
+++ b/arch/ppc/configs/TQM8555_defconfig
@@ -0,0 +1,983 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.15-rc2
+# Thu Nov 24 17:10:52 2005
+#
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_PPC=y
+CONFIG_PPC32=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_CLEAN_COMPILE=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+CONFIG_SYSCTL=y
+# CONFIG_AUDIT is not set
+# CONFIG_HOTPLUG is not set
+CONFIG_KOBJECT_UEVENT=y
+# CONFIG_IKCONFIG is not set
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_EMBEDDED=y
+# CONFIG_KALLSYMS is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+# CONFIG_EPOLL is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SHMEM=y
+CONFIG_CC_ALIGN_FUNCTIONS=0
+CONFIG_CC_ALIGN_LABELS=0
+CONFIG_CC_ALIGN_LOOPS=0
+CONFIG_CC_ALIGN_JUMPS=0
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+
+#
+# Loadable module support
+#
+# CONFIG_MODULES is not set
+
+#
+# Block layer
+#
+# CONFIG_LBD is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# Processor
+#
+# CONFIG_6xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_POWER3 is not set
+# CONFIG_POWER4 is not set
+# CONFIG_8xx is not set
+# CONFIG_E200 is not set
+CONFIG_E500=y
+CONFIG_BOOKE=y
+CONFIG_FSL_BOOKE=y
+# CONFIG_PHYS_64BIT is not set
+CONFIG_SPE=y
+CONFIG_MATH_EMULATION=y
+# CONFIG_KEXEC is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_WANT_EARLY_SERIAL is not set
+CONFIG_PPC_GEN550=y
+CONFIG_85xx=y
+CONFIG_PPC_INDIRECT_PCI_BE=y
+
+#
+# Freescale 85xx options
+#
+# CONFIG_MPC8540_ADS is not set
+# CONFIG_MPC8548_CDS is not set
+# CONFIG_MPC8555_CDS is not set
+# CONFIG_MPC8560_ADS is not set
+# CONFIG_SBC8560 is not set
+# CONFIG_STX_GP3 is not set
+# CONFIG_TQM8540 is not set
+# CONFIG_TQM8541 is not set
+CONFIG_TQM8555=y
+# CONFIG_TQM8560 is not set
+CONFIG_MPC8555=y
+
+#
+# Platform options
+#
+CONFIG_CPM2=y
+# CONFIG_PC_KEYBOARD is not set
+# CONFIG_HIGHMEM is not set
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+# CONFIG_SOFTWARE_SUSPEND is not set
+CONFIG_SECCOMP=y
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_PPC_I8259=y
+CONFIG_PPC_INDIRECT_PCI=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+# CONFIG_PCI_LEGACY_PROC is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_BOOT_LOAD=0x00800000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_BIC=y
+# CONFIG_IPV6 is not set
+# CONFIG_NETFILTER is not set
+
+#
+# DCCP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_DCCP is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_NET_DIVERT is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_IEEE80211 is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
+
+#
+# Memory Technology Devices (MTD)
+#
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_AMDSTD_RETRY=0
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_TQM85xx=y
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLKMTD is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+
+#
+# NAND Flash Device Drivers
+#
+# CONFIG_MTD_NAND is not set
+
+#
+# OneNAND Flash Device Drivers
+#
+# CONFIG_MTD_ONENAND is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=32768
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+
+#
+# ATA/ATAPI/MFM/RLL support
+#
+CONFIG_IDE=y
+CONFIG_BLK_DEV_IDE=y
+
+#
+# Please see Documentation/ide.txt for help/info on IDE drives
+#
+# CONFIG_BLK_DEV_IDE_SATA is not set
+CONFIG_BLK_DEV_IDEDISK=y
+# CONFIG_IDEDISK_MULTI_MODE is not set
+# CONFIG_BLK_DEV_IDECD is not set
+# CONFIG_BLK_DEV_IDETAPE is not set
+# CONFIG_BLK_DEV_IDEFLOPPY is not set
+# CONFIG_IDE_TASK_IOCTL is not set
+
+#
+# IDE chipset support/bugfixes
+#
+CONFIG_IDE_GENERIC=y
+CONFIG_BLK_DEV_IDEPCI=y
+CONFIG_IDEPCI_SHARE_IRQ=y
+# CONFIG_BLK_DEV_OFFBOARD is not set
+CONFIG_BLK_DEV_GENERIC=y
+# CONFIG_BLK_DEV_OPTI621 is not set
+# CONFIG_BLK_DEV_SL82C105 is not set
+CONFIG_BLK_DEV_IDEDMA_PCI=y
+# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
+CONFIG_IDEDMA_PCI_AUTO=y
+# CONFIG_IDEDMA_ONLYDISK is not set
+# CONFIG_BLK_DEV_AEC62XX is not set
+# CONFIG_BLK_DEV_ALI15X3 is not set
+# CONFIG_BLK_DEV_AMD74XX is not set
+# CONFIG_BLK_DEV_CMD64X is not set
+# CONFIG_BLK_DEV_TRIFLEX is not set
+# CONFIG_BLK_DEV_CY82C693 is not set
+# CONFIG_BLK_DEV_CS5520 is not set
+# CONFIG_BLK_DEV_CS5530 is not set
+# CONFIG_BLK_DEV_HPT34X is not set
+# CONFIG_BLK_DEV_HPT366 is not set
+# CONFIG_BLK_DEV_SC1200 is not set
+# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT821X is not set
+# CONFIG_BLK_DEV_NS87415 is not set
+# CONFIG_BLK_DEV_PDC202XX_OLD is not set
+# CONFIG_BLK_DEV_PDC202XX_NEW is not set
+# CONFIG_BLK_DEV_SVWKS is not set
+# CONFIG_BLK_DEV_SIIMAGE is not set
+# CONFIG_BLK_DEV_SLC90E66 is not set
+# CONFIG_BLK_DEV_TRM290 is not set
+CONFIG_BLK_DEV_VIA82CXXX=y
+# CONFIG_IDE_ARM is not set
+CONFIG_BLK_DEV_IDEDMA=y
+# CONFIG_IDEDMA_IVB is not set
+CONFIG_IDEDMA_AUTO=y
+# CONFIG_BLK_DEV_HD is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Fusion MPT device support
+#
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_IEEE1394 is not set
+
+#
+# I2O device support
+#
+# CONFIG_I2O is not set
+
+#
+# Macintosh device drivers
+#
+# CONFIG_WINDFARM is not set
+
+#
+# Network device support
+#
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+
+#
+# ARCnet devices
+#
+# CONFIG_ARCNET is not set
+
+#
+# PHY device support
+#
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+# CONFIG_NET_VENDOR_3COM is not set
+
+#
+# Tulip family network device support
+#
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+CONFIG_NET_PCI=y
+# CONFIG_PCNET32 is not set
+# CONFIG_AMD8111_ETH is not set
+# CONFIG_ADAPTEC_STARFIRE is not set
+# CONFIG_B44 is not set
+# CONFIG_FORCEDETH is not set
+# CONFIG_DGRS is not set
+# CONFIG_EEPRO100 is not set
+CONFIG_E100=y
+# CONFIG_FEALNX is not set
+# CONFIG_NATSEMI is not set
+# CONFIG_NE2K_PCI is not set
+# CONFIG_8139CP is not set
+# CONFIG_8139TOO is not set
+# CONFIG_SIS900 is not set
+# CONFIG_EPIC100 is not set
+# CONFIG_SUNDANCE is not set
+# CONFIG_TLAN is not set
+# CONFIG_VIA_RHINE is not set
+# CONFIG_FS_ENET is not set
+
+#
+# Ethernet (1000 Mbit)
+#
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SK98LIN is not set
+# CONFIG_VIA_VELOCITY is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+CONFIG_GIANFAR=y
+CONFIG_GFAR_NAPI=y
+
+#
+# Ethernet (10000 Mbit)
+#
+# CONFIG_CHELSIO_T1 is not set
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+
+#
+# Token Ring devices
+#
+# CONFIG_TR is not set
+
+#
+# Wireless LAN (non-hamradio)
+#
+# CONFIG_NET_RADIO is not set
+
+#
+# Wan interfaces
+#
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN is not set
+
+#
+# Telephony Support
+#
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_TSDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+# CONFIG_SERIAL_8250_EXTENDED is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_CPM is not set
+# CONFIG_SERIAL_JSM is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+
+#
+# Watchdog Cards
+#
+# CONFIG_WATCHDOG is not set
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+
+#
+# Ftape, the floppy tape device driver
+#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+# CONFIG_TELCLOCK is not set
+
+#
+# I2C support
+#
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+# CONFIG_I2C_ALI1535 is not set
+# CONFIG_I2C_ALI1563 is not set
+# CONFIG_I2C_ALI15X3 is not set
+# CONFIG_I2C_AMD756 is not set
+# CONFIG_I2C_AMD8111 is not set
+# CONFIG_I2C_I801 is not set
+# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_PIIX4 is not set
+CONFIG_I2C_MPC=y
+# CONFIG_I2C_NFORCE2 is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_PROSAVAGE is not set
+# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_SCx200_ACB is not set
+# CONFIG_I2C_SIS5595 is not set
+# CONFIG_I2C_SIS630 is not set
+# CONFIG_I2C_SIS96X is not set
+# CONFIG_I2C_VIA is not set
+# CONFIG_I2C_VIAPRO is not set
+# CONFIG_I2C_VOODOO3 is not set
+# CONFIG_I2C_PCA_ISA is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+CONFIG_SENSORS_DS1337=y
+# CONFIG_SENSORS_DS1374 is not set
+# CONFIG_SENSORS_EEPROM is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_RTC8564 is not set
+# CONFIG_SENSORS_M41T00 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_RTC_X1205_I2C is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Hardware Monitoring support
+#
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_ADM1021 is not set
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ASB100 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_FSCHER is not set
+# CONFIG_SENSORS_FSCPOS is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+CONFIG_SENSORS_LM75=y
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_SIS5595 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_VIA686A is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+CONFIG_HWMON_DEBUG_CHIP=y
+
+#
+# Misc devices
+#
+
+#
+# Multimedia Capabilities Port drivers
+#
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+# CONFIG_DVB is not set
+
+#
+# Graphics support
+#
+# CONFIG_FB is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+
+#
+# USB support
+#
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+# CONFIG_USB is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+
+#
+# MMC/SD Card support
+#
+# CONFIG_MMC is not set
+
+#
+# InfiniBand support
+#
+# CONFIG_INFINIBAND is not set
+
+#
+# SN Devices
+#
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_RELAYFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+# CONFIG_NFS_V3 is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+# CONFIG_9P_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+# CONFIG_MSDOS_PARTITION is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+
+#
+# Native Language Support
+#
+# CONFIG_NLS is not set
+# CONFIG_SCC_ENET is not set
+# CONFIG_FEC_ENET is not set
+
+#
+# CPM2 Options
+#
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+CONFIG_CRC32=y
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+# CONFIG_DEBUG_KERNEL is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_KGDB_CONSOLE is not set
+# CONFIG_SERIAL_TEXT_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+# CONFIG_CRYPTO is not set
+
+#
+# Hardware crypto devices
+#
diff --git a/arch/ppc/configs/TQM8560_defconfig b/arch/ppc/configs/TQM8560_defconfig
new file mode 100644
index 0000000..1d90207
--- /dev/null
+++ b/arch/ppc/configs/TQM8560_defconfig
@@ -0,0 +1,992 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.15-rc2
+# Wed Nov 30 16:47:53 2005
+#
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_PPC=y
+CONFIG_PPC32=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_CLEAN_COMPILE=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+CONFIG_SYSCTL=y
+# CONFIG_AUDIT is not set
+# CONFIG_HOTPLUG is not set
+CONFIG_KOBJECT_UEVENT=y
+# CONFIG_IKCONFIG is not set
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_EMBEDDED=y
+# CONFIG_KALLSYMS is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+# CONFIG_EPOLL is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SHMEM=y
+CONFIG_CC_ALIGN_FUNCTIONS=0
+CONFIG_CC_ALIGN_LABELS=0
+CONFIG_CC_ALIGN_LOOPS=0
+CONFIG_CC_ALIGN_JUMPS=0
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+
+#
+# Loadable module support
+#
+# CONFIG_MODULES is not set
+
+#
+# Block layer
+#
+# CONFIG_LBD is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# Processor
+#
+# CONFIG_6xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_POWER3 is not set
+# CONFIG_POWER4 is not set
+# CONFIG_8xx is not set
+# CONFIG_E200 is not set
+CONFIG_E500=y
+CONFIG_BOOKE=y
+CONFIG_FSL_BOOKE=y
+# CONFIG_PHYS_64BIT is not set
+CONFIG_SPE=y
+CONFIG_MATH_EMULATION=y
+# CONFIG_KEXEC is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_WANT_EARLY_SERIAL is not set
+CONFIG_85xx=y
+CONFIG_PPC_INDIRECT_PCI_BE=y
+
+#
+# Freescale 85xx options
+#
+# CONFIG_MPC8540_ADS is not set
+# CONFIG_MPC8548_CDS is not set
+# CONFIG_MPC8555_CDS is not set
+# CONFIG_MPC8560_ADS is not set
+# CONFIG_SBC8560 is not set
+# CONFIG_STX_GP3 is not set
+# CONFIG_TQM8540 is not set
+# CONFIG_TQM8541 is not set
+# CONFIG_TQM8555 is not set
+CONFIG_TQM8560=y
+CONFIG_MPC8560=y
+
+#
+# Platform options
+#
+CONFIG_CPM2=y
+# CONFIG_PC_KEYBOARD is not set
+# CONFIG_HIGHMEM is not set
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+# CONFIG_SOFTWARE_SUSPEND is not set
+CONFIG_SECCOMP=y
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_PPC_I8259=y
+CONFIG_PPC_INDIRECT_PCI=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+# CONFIG_PCI_LEGACY_PROC is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+# CONFIG_RAPIDIO is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_BOOT_LOAD=0x00800000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_BIC=y
+# CONFIG_IPV6 is not set
+# CONFIG_NETFILTER is not set
+
+#
+# DCCP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_DCCP is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_NET_DIVERT is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_IEEE80211 is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
+
+#
+# Memory Technology Devices (MTD)
+#
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_AMDSTD_RETRY=0
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_TQM85xx=y
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLKMTD is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+
+#
+# NAND Flash Device Drivers
+#
+# CONFIG_MTD_NAND is not set
+
+#
+# OneNAND Flash Device Drivers
+#
+# CONFIG_MTD_ONENAND is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=32768
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+
+#
+# ATA/ATAPI/MFM/RLL support
+#
+CONFIG_IDE=y
+CONFIG_BLK_DEV_IDE=y
+
+#
+# Please see Documentation/ide.txt for help/info on IDE drives
+#
+# CONFIG_BLK_DEV_IDE_SATA is not set
+CONFIG_BLK_DEV_IDEDISK=y
+# CONFIG_IDEDISK_MULTI_MODE is not set
+# CONFIG_BLK_DEV_IDECD is not set
+# CONFIG_BLK_DEV_IDETAPE is not set
+# CONFIG_BLK_DEV_IDEFLOPPY is not set
+# CONFIG_IDE_TASK_IOCTL is not set
+
+#
+# IDE chipset support/bugfixes
+#
+CONFIG_IDE_GENERIC=y
+CONFIG_BLK_DEV_IDEPCI=y
+CONFIG_IDEPCI_SHARE_IRQ=y
+# CONFIG_BLK_DEV_OFFBOARD is not set
+CONFIG_BLK_DEV_GENERIC=y
+# CONFIG_BLK_DEV_OPTI621 is not set
+# CONFIG_BLK_DEV_SL82C105 is not set
+CONFIG_BLK_DEV_IDEDMA_PCI=y
+# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
+CONFIG_IDEDMA_PCI_AUTO=y
+# CONFIG_IDEDMA_ONLYDISK is not set
+# CONFIG_BLK_DEV_AEC62XX is not set
+# CONFIG_BLK_DEV_ALI15X3 is not set
+# CONFIG_BLK_DEV_AMD74XX is not set
+# CONFIG_BLK_DEV_CMD64X is not set
+# CONFIG_BLK_DEV_TRIFLEX is not set
+# CONFIG_BLK_DEV_CY82C693 is not set
+# CONFIG_BLK_DEV_CS5520 is not set
+# CONFIG_BLK_DEV_CS5530 is not set
+# CONFIG_BLK_DEV_HPT34X is not set
+# CONFIG_BLK_DEV_HPT366 is not set
+# CONFIG_BLK_DEV_SC1200 is not set
+# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT821X is not set
+# CONFIG_BLK_DEV_NS87415 is not set
+# CONFIG_BLK_DEV_PDC202XX_OLD is not set
+# CONFIG_BLK_DEV_PDC202XX_NEW is not set
+# CONFIG_BLK_DEV_SVWKS is not set
+# CONFIG_BLK_DEV_SIIMAGE is not set
+# CONFIG_BLK_DEV_SLC90E66 is not set
+# CONFIG_BLK_DEV_TRM290 is not set
+CONFIG_BLK_DEV_VIA82CXXX=y
+# CONFIG_IDE_ARM is not set
+CONFIG_BLK_DEV_IDEDMA=y
+# CONFIG_IDEDMA_IVB is not set
+CONFIG_IDEDMA_AUTO=y
+# CONFIG_BLK_DEV_HD is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Fusion MPT device support
+#
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_IEEE1394 is not set
+
+#
+# I2O device support
+#
+# CONFIG_I2O is not set
+
+#
+# Macintosh device drivers
+#
+# CONFIG_WINDFARM is not set
+
+#
+# Network device support
+#
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+
+#
+# ARCnet devices
+#
+# CONFIG_ARCNET is not set
+
+#
+# PHY device support
+#
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+# CONFIG_NET_VENDOR_3COM is not set
+
+#
+# Tulip family network device support
+#
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+CONFIG_NET_PCI=y
+# CONFIG_PCNET32 is not set
+# CONFIG_AMD8111_ETH is not set
+# CONFIG_ADAPTEC_STARFIRE is not set
+# CONFIG_B44 is not set
+# CONFIG_FORCEDETH is not set
+# CONFIG_DGRS is not set
+# CONFIG_EEPRO100 is not set
+CONFIG_E100=y
+# CONFIG_FEALNX is not set
+# CONFIG_NATSEMI is not set
+# CONFIG_NE2K_PCI is not set
+# CONFIG_8139CP is not set
+# CONFIG_8139TOO is not set
+# CONFIG_SIS900 is not set
+# CONFIG_EPIC100 is not set
+# CONFIG_SUNDANCE is not set
+# CONFIG_TLAN is not set
+# CONFIG_VIA_RHINE is not set
+# CONFIG_FS_ENET is not set
+
+#
+# Ethernet (1000 Mbit)
+#
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SK98LIN is not set
+# CONFIG_VIA_VELOCITY is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+CONFIG_GIANFAR=y
+CONFIG_GFAR_NAPI=y
+
+#
+# Ethernet (10000 Mbit)
+#
+# CONFIG_CHELSIO_T1 is not set
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+
+#
+# Token Ring devices
+#
+# CONFIG_TR is not set
+
+#
+# Wireless LAN (non-hamradio)
+#
+# CONFIG_NET_RADIO is not set
+
+#
+# Wan interfaces
+#
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN is not set
+
+#
+# Telephony Support
+#
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_TSDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+# CONFIG_SERIAL_8250_EXTENDED is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_CPM=y
+CONFIG_SERIAL_CPM_CONSOLE=y
+CONFIG_SERIAL_CPM_SCC1=y
+# CONFIG_SERIAL_CPM_SCC2 is not set
+# CONFIG_SERIAL_CPM_SCC3 is not set
+# CONFIG_SERIAL_CPM_SCC4 is not set
+# CONFIG_SERIAL_CPM_SMC1 is not set
+# CONFIG_SERIAL_CPM_SMC2 is not set
+# CONFIG_SERIAL_JSM is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+
+#
+# Watchdog Cards
+#
+# CONFIG_WATCHDOG is not set
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+
+#
+# Ftape, the floppy tape device driver
+#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+# CONFIG_TELCLOCK is not set
+
+#
+# I2C support
+#
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+# CONFIG_I2C_ALI1535 is not set
+# CONFIG_I2C_ALI1563 is not set
+# CONFIG_I2C_ALI15X3 is not set
+# CONFIG_I2C_AMD756 is not set
+# CONFIG_I2C_AMD8111 is not set
+# CONFIG_I2C_I801 is not set
+# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_PIIX4 is not set
+CONFIG_I2C_MPC=y
+# CONFIG_I2C_MPC8260 is not set
+# CONFIG_I2C_NFORCE2 is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_PROSAVAGE is not set
+# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_SCx200_ACB is not set
+# CONFIG_I2C_SIS5595 is not set
+# CONFIG_I2C_SIS630 is not set
+# CONFIG_I2C_SIS96X is not set
+# CONFIG_I2C_VIA is not set
+# CONFIG_I2C_VIAPRO is not set
+# CONFIG_I2C_VOODOO3 is not set
+# CONFIG_I2C_PCA_ISA is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+CONFIG_SENSORS_DS1337=y
+# CONFIG_SENSORS_DS1374 is not set
+# CONFIG_SENSORS_EEPROM is not set
+# CONFIG_SENSORS_MAX6900 is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCF8563 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_RTC8564 is not set
+# CONFIG_SENSORS_M41T00 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_RTC_X1205_I2C is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Hardware Monitoring support
+#
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_ADM1021 is not set
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ASB100 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_FSCHER is not set
+# CONFIG_SENSORS_FSCPOS is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+CONFIG_SENSORS_LM75=y
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_SIS5595 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_VIA686A is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+CONFIG_HWMON_DEBUG_CHIP=y
+
+#
+# Misc devices
+#
+
+#
+# Multimedia Capabilities Port drivers
+#
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+# CONFIG_DVB is not set
+
+#
+# Graphics support
+#
+# CONFIG_FB is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+
+#
+# USB support
+#
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+# CONFIG_USB is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+
+#
+# MMC/SD Card support
+#
+# CONFIG_MMC is not set
+
+#
+# InfiniBand support
+#
+# CONFIG_INFINIBAND is not set
+
+#
+# SN Devices
+#
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_RELAYFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+# CONFIG_NFS_V3 is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+# CONFIG_9P_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+# CONFIG_MSDOS_PARTITION is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+
+#
+# Native Language Support
+#
+# CONFIG_NLS is not set
+# CONFIG_SCC_ENET is not set
+# CONFIG_FEC_ENET is not set
+
+#
+# CPM2 Options
+#
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+CONFIG_CRC32=y
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+# CONFIG_DEBUG_KERNEL is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_KGDB_CONSOLE is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+# CONFIG_CRYPTO is not set
+
+#
+# Hardware crypto devices
+#
diff --git a/arch/ppc/platforms/85xx/Kconfig b/arch/ppc/platforms/85xx/Kconfig
index c5bc282..7ddd331 100644
--- a/arch/ppc/platforms/85xx/Kconfig
+++ b/arch/ppc/platforms/85xx/Kconfig
@@ -39,7 +39,7 @@ config MPC8560_ADS
config SBC8560
bool "WindRiver PowerQUICC III SBC8560"
help
- This option enables support for the WindRiver PowerQUICC III
+ This option enables support for the WindRiver PowerQUICC III
SBC8560 board.
config STX_GP3
@@ -48,6 +48,26 @@ config STX_GP3
This option enables support for the Silicon Turnkey Express GP3
board.
+config TQM8540
+ bool "TQ Components TQM8540"
+ help
+ This option enablese support for the TQ Components TQM8540 board.
+
+config TQM8541
+ bool "TQ Components TQM8541"
+ help
+ This option enablese support for the TQ Components TQM8541 board.
+
+config TQM8555
+ bool "TQ Components TQM8555"
+ help
+ This option enablese support for the TQ Components TQM8555 board.
+
+config TQM8560
+ bool "TQ Components TQM8560"
+ help
+ This option enablese support for the TQ Components TQM8560 board.
+
endchoice
# It's often necessary to know the specific 85xx processor type.
@@ -55,7 +75,7 @@ endchoice
# don't need to ask more redundant questions.
config MPC8540
bool
- depends on MPC8540_ADS
+ depends on MPC8540_ADS || TQM8540
default y
config MPC8548
@@ -65,12 +85,12 @@ config MPC8548
config MPC8555
bool
- depends on MPC8555_CDS
+ depends on MPC8555_CDS || TQM8541 || TQM8555
default y
config MPC8560
bool
- depends on SBC8560 || MPC8560_ADS || STX_GP3
+ depends on SBC8560 || MPC8560_ADS || STX_GP3 || TQM8560
default y
config 85xx_PCI2
diff --git a/arch/ppc/platforms/85xx/Makefile b/arch/ppc/platforms/85xx/Makefile
index efdf813..6c4753c 100644
--- a/arch/ppc/platforms/85xx/Makefile
+++ b/arch/ppc/platforms/85xx/Makefile
@@ -7,3 +7,7 @@ obj-$(CONFIG_MPC8555_CDS) += mpc85xx_cds
obj-$(CONFIG_MPC8560_ADS) += mpc85xx_ads_common.o mpc8560_ads.o
obj-$(CONFIG_SBC8560) += sbc85xx.o sbc8560.o
obj-$(CONFIG_STX_GP3) += stx_gp3.o
+obj-$(CONFIG_TQM8540) += tqm85xx.o
+obj-$(CONFIG_TQM8541) += tqm85xx.o
+obj-$(CONFIG_TQM8555) += tqm85xx.o
+obj-$(CONFIG_TQM8560) += tqm85xx.o
diff --git a/arch/ppc/platforms/85xx/tqm85xx.c b/arch/ppc/platforms/85xx/tqm85xx.c
new file mode 100644
index 0000000..da63da7
--- /dev/null
+++ b/arch/ppc/platforms/85xx/tqm85xx.c
@@ -0,0 +1,419 @@
+/*
+ * arch/ppc/platforms/85xx/tqm85xx.c
+ *
+ * TQM85xx (40/41/55/60) board specific routines
+ *
+ * Copyright (c) 2005 DENX Software Engineering
+ * Stefan Roese <sr@denx.de>
+ *
+ * Based on original work by
+ * Kumar Gala <kumar.gala@freescale.com>
+ * Copyright 2004 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/config.h>
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/reboot.h>
+#include <linux/pci.h>
+#include <linux/kdev_t.h>
+#include <linux/major.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/seq_file.h>
+#include <linux/root_dev.h>
+#include <linux/serial.h>
+#include <linux/tty.h> /* for linux/serial_core.h */
+#include <linux/serial_core.h>
+#include <linux/initrd.h>
+#include <linux/module.h>
+#include <linux/fsl_devices.h>
+
+#include <asm/system.h>
+#include <asm/pgtable.h>
+#include <asm/page.h>
+#include <asm/atomic.h>
+#include <asm/time.h>
+#include <asm/io.h>
+#include <asm/machdep.h>
+#include <asm/open_pic.h>
+#include <asm/bootinfo.h>
+#include <asm/pci-bridge.h>
+#include <asm/mpc85xx.h>
+#include <asm/irq.h>
+#include <asm/immap_85xx.h>
+#include <asm/kgdb.h>
+#include <asm/ppc_sys.h>
+#include <asm/cpm2.h>
+#include <mm/mmu_decl.h>
+
+#include <syslib/ppc85xx_setup.h>
+#include <syslib/cpm2_pic.h>
+#include <syslib/ppc85xx_common.h>
+#include <syslib/ppc85xx_rio.h>
+
+#ifndef CONFIG_PCI
+unsigned long isa_io_base = 0;
+unsigned long isa_mem_base = 0;
+#endif
+
+
+extern unsigned long total_memory; /* in mm/init */
+
+unsigned char __res[sizeof (bd_t)];
+
+/* Internal interrupts are all Level Sensitive, and Positive Polarity */
+static u_char tqm85xx_openpic_initsenses[] __initdata = {
+ MPC85XX_INTERNAL_IRQ_SENSES,
+ 0x0, /* External 0: */
+ 0x0, /* External 1: */
+#if defined(CONFIG_PCI)
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* External 2: PCI INTA */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* External 3: PCI INTB */
+#else
+ 0x0, /* External 2: */
+ 0x0, /* External 3: */
+#endif
+ 0x0, /* External 4: */
+ 0x0, /* External 5: */
+ 0x0, /* External 6: */
+ 0x0, /* External 7: */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* External 8: PHY */
+ 0x0, /* External 9: */
+ 0x0, /* External 10: */
+ 0x0, /* External 11: */
+};
+
+static const char *GFAR_PHY_0 = "phy0:2";
+static const char *GFAR_PHY_1 = "phy0:1";
+#ifdef CONFIG_MPC8540
+static const char *GFAR_PHY_3 = "phy0:3";
+#endif
+
+/* ************************************************************************
+ *
+ * Setup the architecture
+ *
+ */
+static void __init
+tqm85xx_setup_arch(void)
+{
+ bd_t *binfo = (bd_t *) __res;
+ unsigned int freq;
+ struct gianfar_platform_data *pdata;
+ struct gianfar_mdio_data *mdata;
+
+#ifdef CONFIG_MPC8560
+ cpm2_reset();
+#endif
+
+ /* get the core frequency */
+ freq = binfo->bi_intfreq;
+
+ if (ppc_md.progress)
+ ppc_md.progress("tqm85xx_setup_arch()", 0);
+
+ /* Set loops_per_jiffy to a half-way reasonable value,
+ for use until calibrate_delay gets called. */
+ loops_per_jiffy = freq / HZ;
+
+#ifdef CONFIG_PCI
+ /* setup PCI host bridges */
+ mpc85xx_setup_hose();
+#endif
+
+#ifndef CONFIG_MPC8560
+#if defined(CONFIG_SERIAL_8250)
+ mpc85xx_early_serial_map();
+#endif
+
+#ifdef CONFIG_SERIAL_TEXT_DEBUG
+ /* Invalidate the entry we stole earlier the serial ports
+ * should be properly mapped */
+ invalidate_tlbcam_entry(num_tlbcam_entries - 1);
+#endif
+#endif /* CONFIG_MPC8560 */
+
+ /* setup the board related info for the MDIO bus */
+ mdata = (struct gianfar_mdio_data *) ppc_sys_get_pdata(MPC85xx_MDIO);
+
+ mdata->irq[0] = MPC85xx_IRQ_EXT8;
+ mdata->irq[1] = MPC85xx_IRQ_EXT8;
+ mdata->irq[2] = -1;
+ mdata->irq[3] = MPC85xx_IRQ_EXT8;
+ mdata->irq[31] = -1;
+ mdata->paddr += binfo->bi_immr_base;
+
+ /* setup the board related information for the enet controllers */
+ pdata = (struct gianfar_platform_data *) ppc_sys_get_pdata(MPC85xx_TSEC1);
+ if (pdata) {
+ pdata->board_flags = FSL_GIANFAR_BRD_HAS_PHY_INTR;
+ pdata->bus_id = GFAR_PHY_0;
+ memcpy(pdata->mac_addr, binfo->bi_enetaddr, 6);
+ }
+
+ pdata = (struct gianfar_platform_data *) ppc_sys_get_pdata(MPC85xx_TSEC2);
+ if (pdata) {
+ pdata->board_flags = FSL_GIANFAR_BRD_HAS_PHY_INTR;
+ pdata->bus_id = GFAR_PHY_1;
+ memcpy(pdata->mac_addr, binfo->bi_enet1addr, 6);
+ }
+
+#ifdef CONFIG_MPC8540
+ pdata = (struct gianfar_platform_data *) ppc_sys_get_pdata(MPC85xx_FEC);
+ if (pdata) {
+ pdata->board_flags = 0;
+ pdata->bus_id = GFAR_PHY_3;
+ memcpy(pdata->mac_addr, binfo->bi_enet2addr, 6);
+ }
+#endif
+
+#ifdef CONFIG_BLK_DEV_INITRD
+ if (initrd_start)
+ ROOT_DEV = Root_RAM0;
+ else
+#endif
+#ifdef CONFIG_ROOT_NFS
+ ROOT_DEV = Root_NFS;
+#else
+ ROOT_DEV = Root_HDA1;
+#endif
+}
+
+#ifdef CONFIG_MPC8560
+static irqreturn_t cpm2_cascade(int irq, void *dev_id, struct pt_regs *regs)
+{
+ while ((irq = cpm2_get_irq(regs)) >= 0)
+ __do_IRQ(irq, regs);
+ return IRQ_HANDLED;
+}
+
+static struct irqaction cpm2_irqaction = {
+ .handler = cpm2_cascade,
+ .flags = SA_INTERRUPT,
+ .mask = CPU_MASK_NONE,
+ .name = "cpm2_cascade",
+};
+#endif /* CONFIG_MPC8560 */
+
+void __init
+tqm85xx_init_IRQ(void)
+{
+ bd_t *binfo = (bd_t *) __res;
+
+ /* Determine the Physical Address of the OpenPIC regs */
+ phys_addr_t OpenPIC_PAddr =
+ binfo->bi_immr_base + MPC85xx_OPENPIC_OFFSET;
+ OpenPIC_Addr = ioremap(OpenPIC_PAddr, MPC85xx_OPENPIC_SIZE);
+ OpenPIC_InitSenses = tqm85xx_openpic_initsenses;
+ OpenPIC_NumInitSenses = sizeof (tqm85xx_openpic_initsenses);
+
+ /* Skip reserved space and internal sources */
+ openpic_set_sources(0, 32, OpenPIC_Addr + 0x10200);
+
+ /* Map PIC IRQs 0-11 */
+ openpic_set_sources(48, 12, OpenPIC_Addr + 0x10000);
+
+ /* we let openpic interrupts starting from an offset, to
+ * leave space for cascading interrupts underneath.
+ */
+ openpic_init(MPC85xx_OPENPIC_IRQ_OFFSET);
+
+#ifdef CONFIG_MPC8560
+ /* Setup CPM2 PIC */
+ cpm2_init_IRQ();
+
+ setup_irq(MPC85xx_IRQ_CPM, &cpm2_irqaction);
+#endif /* CONFIG_MPC8560 */
+
+ return;
+}
+
+int tqm85xx_show_cpuinfo(struct seq_file *m)
+{
+ uint pvid, svid, phid1;
+ uint memsize = total_memory;
+ bd_t *binfo = (bd_t *) __res;
+ unsigned int freq;
+
+ /* get the core frequency */
+ freq = binfo->bi_intfreq;
+
+ pvid = mfspr(SPRN_PVR);
+ svid = mfspr(SPRN_SVR);
+
+ seq_printf(m, "Vendor\t\t: TQ Components\n");
+ seq_printf(m, "Machine\t\t: TQM%s\n", cur_ppc_sys_spec->ppc_sys_name);
+ seq_printf(m, "clock\t\t: %dMHz\n", freq / 1000000);
+ seq_printf(m, "PVR\t\t: 0x%x\n", pvid);
+ seq_printf(m, "SVR\t\t: 0x%x\n", svid);
+
+ /* Display cpu Pll setting */
+ phid1 = mfspr(SPRN_HID1);
+ seq_printf(m, "PLL setting\t: 0x%x\n", ((phid1 >> 24) & 0x3f));
+
+ /* Display the amount of memory */
+ seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
+
+ return 0;
+}
+
+#if defined(CONFIG_I2C) && defined(CONFIG_SENSORS_DS1337)
+extern ulong ds1337_get_rtc_time(void);
+extern int ds1337_set_rtc_time(unsigned long nowtime);
+
+static int __init
+tqm85xx_rtc_hookup(void)
+{
+ struct timespec tv;
+
+ ppc_md.set_rtc_time = ds1337_set_rtc_time;
+ ppc_md.get_rtc_time = ds1337_get_rtc_time;
+
+ tv.tv_nsec = 0;
+ tv.tv_sec = (ppc_md.get_rtc_time)();
+ do_settimeofday(&tv);
+
+ return 0;
+}
+late_initcall(tqm85xx_rtc_hookup);
+#endif
+
+#ifdef CONFIG_PCI
+/*
+ * interrupt routing
+ */
+int mpc85xx_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char pin)
+{
+ static char pci_irq_table[][4] =
+ /*
+ * PCI IDSEL/INTPIN->INTLINE
+ * A B C D
+ */
+ {
+ {PIRQA, PIRQB, 0, 0},
+ };
+
+ const long min_idsel = 0x1c, max_idsel = 0x1c, irqs_per_slot = 4;
+ return PCI_IRQ_TABLE_LOOKUP;
+}
+
+int mpc85xx_exclude_device(u_char bus, u_char devfn)
+{
+ if (bus == 0 && PCI_SLOT(devfn) == 0)
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ else
+ return PCIBIOS_SUCCESSFUL;
+}
+
+#endif /* CONFIG_PCI */
+
+#ifdef CONFIG_RAPIDIO
+void platform_rio_init(void)
+{
+ /* 512MB RIO LAW at 0xc0000000 */
+ mpc85xx_rio_setup(0xc0000000, 0x20000000);
+}
+#endif /* CONFIG_RAPIDIO */
+
+/* ************************************************************************ */
+void __init
+platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+ unsigned long r6, unsigned long r7)
+{
+ /* parse_bootinfo must always be called first */
+ parse_bootinfo(find_bootinfo());
+
+ /*
+ * If we were passed in a board information, copy it into the
+ * residual data area.
+ */
+ if (r3) {
+ memcpy((void *) __res, (void *) (r3 + KERNELBASE),
+ sizeof (bd_t));
+ }
+
+#if defined(CONFIG_SERIAL_TEXT_DEBUG) && !defined(CONFIG_MPC8560)
+ {
+ bd_t *binfo = (bd_t *) __res;
+ struct uart_port p;
+
+ /* Use the last TLB entry to map CCSRBAR to allow access to DUART regs */
+ settlbcam(num_tlbcam_entries - 1, binfo->bi_immr_base,
+ binfo->bi_immr_base, MPC85xx_CCSRBAR_SIZE, _PAGE_IO, 0);
+
+ memset(&p, 0, sizeof (p));
+ p.iotype = SERIAL_IO_MEM;
+ p.membase = (void *) binfo->bi_immr_base + MPC85xx_UART0_OFFSET;
+ p.uartclk = binfo->bi_busfreq;
+
+ gen550_init(0, &p);
+
+ memset(&p, 0, sizeof (p));
+ p.iotype = SERIAL_IO_MEM;
+ p.membase = (void *) binfo->bi_immr_base + MPC85xx_UART1_OFFSET;
+ p.uartclk = binfo->bi_busfreq;
+
+ gen550_init(1, &p);
+ }
+#endif
+
+#if defined(CONFIG_BLK_DEV_INITRD)
+ /*
+ * If the init RAM disk has been configured in, and there's a valid
+ * starting address for it, set it up.
+ */
+ if (r4) {
+ initrd_start = r4 + KERNELBASE;
+ initrd_end = r5 + KERNELBASE;
+ }
+#endif /* CONFIG_BLK_DEV_INITRD */
+
+ /* Copy the kernel command line arguments to a safe place. */
+
+ if (r6) {
+ *(char *) (r7 + KERNELBASE) = 0;
+ strcpy(cmd_line, (char *) (r6 + KERNELBASE));
+ }
+
+ identify_ppc_sys_by_id(mfspr(SPRN_SVR));
+
+ /* setup the PowerPC module struct */
+ ppc_md.setup_arch = tqm85xx_setup_arch;
+ ppc_md.show_cpuinfo = tqm85xx_show_cpuinfo;
+
+ ppc_md.init_IRQ = tqm85xx_init_IRQ;
+ ppc_md.get_irq = openpic_get_irq;
+
+ ppc_md.restart = mpc85xx_restart;
+ ppc_md.power_off = mpc85xx_power_off;
+ ppc_md.halt = mpc85xx_halt;
+
+ ppc_md.find_end_of_memory = mpc85xx_find_end_of_memory;
+
+ ppc_md.time_init = NULL;
+ ppc_md.set_rtc_time = NULL;
+ ppc_md.get_rtc_time = NULL;
+ ppc_md.calibrate_decr = mpc85xx_calibrate_decr;
+
+#ifndef CONFIG_MPC8560
+#if defined(CONFIG_SERIAL_8250) && defined(CONFIG_SERIAL_TEXT_DEBUG)
+ ppc_md.progress = gen550_progress;
+#endif /* CONFIG_SERIAL_8250 && CONFIG_SERIAL_TEXT_DEBUG */
+#if defined(CONFIG_SERIAL_8250) && defined(CONFIG_KGDB)
+ ppc_md.early_serial_map = mpc85xx_early_serial_map;
+#endif /* CONFIG_SERIAL_8250 && CONFIG_KGDB */
+#endif /* CONFIG_MPC8560 */
+
+ if (ppc_md.progress)
+ ppc_md.progress("tqm85xx_init(): exit", 0);
+
+ return;
+}
diff --git a/arch/ppc/platforms/85xx/tqm85xx.h b/arch/ppc/platforms/85xx/tqm85xx.h
new file mode 100644
index 0000000..3775eb3
--- /dev/null
+++ b/arch/ppc/platforms/85xx/tqm85xx.h
@@ -0,0 +1,56 @@
+/*
+ * arch/ppc/platforms/85xx/tqm85xx.h
+ *
+ * TQM85xx (40/41/55/60) board definitions
+ *
+ * Copyright (c) 2005 DENX Software Engineering
+ * Stefan Roese <sr@denx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#ifndef __MACH_TQM85XX_H
+#define __MACH_TQM85XX_H
+
+#include <linux/config.h>
+#include <linux/init.h>
+#include <asm/ppcboot.h>
+
+#define BOARD_CCSRBAR ((uint)0xe0000000)
+#define CCSRBAR_SIZE ((uint)1024*1024)
+
+#define CPM_MAP_ADDR (CCSRBAR + MPC85xx_CPM_OFFSET)
+
+#define PCI_CFG_ADDR_OFFSET (0x8000)
+#define PCI_CFG_DATA_OFFSET (0x8004)
+
+/* PCI interrupt controller */
+#define PIRQA MPC85xx_IRQ_EXT2
+#define PIRQB MPC85xx_IRQ_EXT3
+
+#define MPC85XX_PCI1_LOWER_IO 0x00000000
+#define MPC85XX_PCI1_UPPER_IO 0x00ffffff
+
+#define MPC85XX_PCI1_LOWER_MEM 0x80000000
+#define MPC85XX_PCI1_UPPER_MEM 0x9fffffff
+
+#define MPC85XX_PCI1_IO_BASE 0xe2000000
+#define MPC85XX_PCI1_MEM_OFFSET 0x00000000
+
+#define MPC85XX_PCI1_IO_SIZE 0x01000000
+
+#define BASE_BAUD 115200
+
+extern void mpc85xx_setup_hose(void) __init;
+extern void mpc85xx_restart(char *cmd);
+extern void mpc85xx_power_off(void);
+extern void mpc85xx_halt(void);
+extern void mpc85xx_init_IRQ(void) __init;
+extern unsigned long mpc85xx_find_end_of_memory(void) __init;
+extern void mpc85xx_calibrate_decr(void) __init;
+
+#endif /* __MACH_TQM85XX_H */
diff --git a/include/asm-ppc/mpc85xx.h b/include/asm-ppc/mpc85xx.h
index 9d14bae..c8a96aa 100644
--- a/include/asm-ppc/mpc85xx.h
+++ b/include/asm-ppc/mpc85xx.h
@@ -37,6 +37,10 @@
#ifdef CONFIG_STX_GP3
#include <platforms/85xx/stx_gp3.h>
#endif
+#if defined(CONFIG_TQM8540) || defined(CONFIG_TQM8541) || \
+ defined(CONFIG_TQM8555) || defined(CONFIG_TQM8560)
+#include <platforms/85xx/tqm85xx.h>
+#endif
#define _IO_BASE isa_io_base
#define _ISA_MEM_BASE isa_mem_base
\f
!-------------------------------------------------------------flip-
^ permalink raw reply related
* Re: Linux hangs while Uncompressing
From: Carl Ljungmark @ 2005-12-01 12:15 UTC (permalink / raw)
To: pritha.bhattacharya, linuxppc-embedded
In-Reply-To: <OF0098DF7F.857DE409-ON652570CA.001AA3F7-652570CA.0036DB32@tcs.com>
Try to change your 'load address' and 'entry address' to a more sensible =
=20
value, maybe 0x30080000 or so. This is done when you create the PPCBOOT =20
image with mkimage, by passing parameters -a and -e respectively. Right =20
now, U-boot tries to uncompress the kernel into your boot flash, which =20
hopefully is hw-protected..
good luck
/Carl
On Thu, 01 Dec 2005 10:59:10 +0100, <pritha.bhattacharya@tcs.com> wrote:
>
> Hi All,
>
> I have RAM version of U-Boot which is running on a board similar to
> MPC8260. My memory map isas follows:
>
> Staring address Device Size Memory
> controller and CS
>
> 0000 0000
> 0800 0000
> FFF0 0000
> 0F00 0000
> 3000 0000
> 3800 0000
> 4200 0000
> 5000 0000
> FLASH (Boot)
> FLASH (Code)
> SSRAM
> CPU internal registers
> SDRAM
> SDRAM
> Framer
> DSP 8102
> 1MB (512Kx16)
> 4 MB (1Mx16)
> 2 MB (512Kx36)
> 128 KB
> 128 MB (16Mx72)
> 128 MB (16Mx72)
> 1 MB
> 2 MB
> BR0/OR0: CS0
> BR1/OR1: CS1
> BR2/OR2: CS2
>
> BR3/OR3: CS3
> BR4/OR4: CS4
> BR5/OR5: CS5
> BR6/OR6: CS6
>
>
> I have downloaded Linux 2.4.25 kernel image through kermit. after
> downloading the image in SDRAM location 0x30000000 and giving the comma=
nd
> bootm 0x30000000
>
> the prompt shows a message:
>
>
> TCS-PIC-UBOOT=3D> loadb 0x30000000## Ready for binary (kermit) download=
to
> 0x30000000 at 57600 bps...
>
> ## Total Size =3D 0x000936f6 =3D 603894 Bytes
> ## Start Addr =3D 0x30000000
> TCS-PIC-UBOOT=3D> bootm 0x30000000## Booting image at 30000000 ...
> Image Name: Linux-2.4.25
> Image Type: PowerPC Linux Kernel Image (gzip compressed)
> Data Size: 603830 Bytes =3D 589.7 kB
> Load Address: 00000000
> Entry Point: 00000000
> Verifying Checksum ... OK
> Uncompressing Kernel Image ...
>
> The system hangs here and is not able to uncompress the kernel any
> further. I have checked in the FAQs provided in the denx's site, but =20
> could
> not find anything similar to my case.
>
> I would appreciate any help.
>
> Thanks & Regards,
> Pritha Bhattacharya
> Tata Consultancy Services Limited
> Mailto: pritha.bhattacharya@tcs.com
> Website: http://www.tcs.com
>
> Notice: The information contained in this e-mail message and/or =20
> attachments to it may contain confidential or privileged information. =
=20
> If you are not the intended recipient, any dissemination, use, review, =
=20
> distribution, printing or copying of the information contained in this =
=20
> e-mail message and/or attachments to it are strictly prohibited. If =20
> you have received this communication in error, please notify us by repl=
y =20
> e-mail or telephone and immediately and permanently delete the message =
=20
> and any attachments. Thank you
^ permalink raw reply
* Re: MPC8555 8280/8270 USB host support
From: Hans Schillstrom @ 2005-12-01 12:26 UTC (permalink / raw)
To: Mike Rapoport; +Cc: 'linuxppc-embedded@ozlabs.org'
In-Reply-To: <43798741.5070604@compulab.co.il>
[-- Attachment #1: Type: text/plain, Size: 1475 bytes --]
Hi Mike
I've made some modifications due to the difference between mpc8272 and
mpc8270. MPC8272 use SCC3 and MPC8270 use SCC4.
Added some more clock configuration options ...
I think the changes are quite generic.
The driver seems to work with a 2.6.13 kernel.
Only some basic tests is performed with
- serial ftdi_sio to ports ttyUSB0 & ttyUSB1
- storage i.e. some kind of "no name" usb-memory
- 3 1/4 floppy drive
- Nokia hub.
Don't you think u-boot should take care of clock setup
i.e. as much as possible of all board dependent stuff ?
Regards
Hans Schillstrom
On Tue, 2005-11-15 at 07:59, Mike Rapoport wrote:
> Hans Schillstrom wrote:
>
> >Hi Mike
> >I'm working with a 8270 board and 2.6.12 kernel and searching for USB
> >drivers.
> >
> >Could you help me finding the files ?
> >
> >
> I've opened a project on the SourceForge,
> http://cpm2usb.sourceforge.net. The file containing patch against
> 2.6.12.3 can be downloaded at http://sourceforge.net/projects/cpm2usb.
>
> >I can help you with the testing.
> >What status do they have right now ?
> >
> >
> The driver was developed on MPC8272ADS, but should go as well on 8270
> since they have the same USB host controller AFAIK.
> Currently, as far as I tested it works fine with full-speed single
> device attached through hub, but fails is there are transfers from/to
> several devices simultaneously.
> As for the code itself, it's far from being perfect.
>
> >Regards
> >Hans
> >
> >
>
[-- Attachment #2: m8270usb.patch --]
[-- Type: text/x-patch, Size: 6861 bytes --]
diff -Nruw linux-2.6.13.2/drivers/usb/host/m82xx-hcd.c linux-2.6-dev/drivers/usb/host/m82xx-hcd.c
--- linux-2.6.13.2/drivers/usb/host/m82xx-hcd.c 2005-12-01 10:58:55.000000000 +0100
+++ linux-2.6-dev/drivers/usb/host/m82xx-hcd.c 2005-12-01 12:59:27.000000000 +0100
@@ -12,6 +12,9 @@
* George Panageas <gpana@intracom.gr>
* Pantelis Antoniou <panto@intracom.gr>
*
+ * Fixes for MPC8270/80 & adaptions to powervave technologies rcb8270 board.
+ * Hans Schillstrom <hans.schillstrom@pwav.com>
+ *
* designed for the EmbeddedPlanet RPX lite board
* (C) Copyright 2000 Embedded Planet
* http://www.embeddedplanet.com
@@ -110,6 +113,15 @@
*bcsr_usb |= BCSR_USB_POWER;
}
+#elif defined(CONFIG_RCB8270)
+ hp->usb_clock = USB_CLOCK_PC25_CLK7;
+ {
+ volatile cpm2_map_t *immap = (volatile cpm2_map_t *)CPM_MAP_ADDR;
+ volatile iop_cpm2_t *io = &immap->im_ioport;
+
+ io->iop_pdata &= ~(1 << (31 - 2)); // Turn on power tu usb driver
+ udelay(1000);
+ }
#endif
return 0;
}
@@ -167,26 +179,39 @@
volatile cpmux_t *cm = &immap->im_cpmux;
switch (usb_clock) {
+ case USB_CLOCK_PC27_CLK5:
+ io->iop_pdirc &= ~PC_CLK5_48MHz;
+ io->iop_psorc &= ~PC_CLK5_48MHz;
+ io->iop_pparc |= PC_CLK5_48MHz;
+ cm->cmx_scr &= ~USB_CMX_SCR_MASK;
+ cm->cmx_scr |= USB_CMX_CLK5;
+ break;
case USB_CLOCK_PC26_CLK6:
io->iop_pdirc &= ~PC_CLK6_48MHz;
io->iop_psorc &= ~PC_CLK6_48MHz;
io->iop_pparc |= PC_CLK6_48MHz;
- cm->cmx_scr &= ~0x0000ff00;
- cm->cmx_scr |= 0x00003f00;
+ cm->cmx_scr &= ~USB_CMX_SCR_MASK;
+ cm->cmx_scr |= USB_CMX_CLK6;
+ break;
+ case USB_CLOCK_PC25_CLK7:
+ io->iop_pdirc &= ~PC_CLK7_48MHz; // Input mode
+ io->iop_psorc &= ~PC_CLK7_48MHz; // special option
+ io->iop_pparc |= PC_CLK7_48MHz; // Dedicated port
+ cm->cmx_scr &= ~USB_CMX_SCR_MASK;
+ cm->cmx_scr |= USB_CMX_CLK7;
break;
case USB_CLOCK_PC24_CLK8:
io->iop_pdirc &= ~PC_CLK8_48MHz;
io->iop_psorc &= ~PC_CLK8_48MHz;
io->iop_pparc |= PC_CLK8_48MHz;
- cm->cmx_scr &= ~0x0000ff00;
- cm->cmx_scr |= 0x00003f00;
+ cm->cmx_scr &= ~USB_CMX_SCR_MASK;
+ cm->cmx_scr |= USB_CMX_CLK8;
break;
default:
printk(KERN_ERR "m8xxhci: invalid usb_clock value %d!\n", usb_clock);
return -1;
}
-
return 0;
}
@@ -317,13 +342,21 @@
#define USB_MODE_PIN ((uint)(1 << (31 - 0)))
#define USB_SPEED_PIN ((uint)(1 << (31 - 23)))
#define USB_SUSPEND_PIN ((uint)(1 << (31 - 29)))
-
-
io->iop_pdirc |= (USB_MODE_PIN | USB_SPEED_PIN | USB_SUSPEND_PIN);
io->iop_pparc &= ~(USB_MODE_PIN | USB_SPEED_PIN | USB_SUSPEND_PIN);
io->iop_pdatc |= (USB_MODE_PIN | USB_SPEED_PIN);
io->iop_podrc |= USB_MODE_PIN;
io->iop_pdatc &= ~(USB_SUSPEND_PIN);
+
+#elif defined(CONFIG_RCB8270)
+
+#define USB_MODE_PIN ((uint)(1 << (31 - 0)))
+#define USB_SPEED_PIN ((uint)(1 << (31 - 5)))
+
+ io->iop_pdirc |= (USB_MODE_PIN | USB_SPEED_PIN );
+ io->iop_pparc &= ~(USB_MODE_PIN | USB_SPEED_PIN );
+ io->iop_pdatc |= (USB_MODE_PIN | USB_SPEED_PIN);
+ io->iop_podrc |= USB_MODE_PIN;
#endif
msleep(10);
diff -Nruw linux-2.6.13.2/drivers/usb/host/m82xx-hcd.h linux-2.6-dev/drivers/usb/host/m82xx-hcd.h
--- linux-2.6.13.2/drivers/usb/host/m82xx-hcd.h 2005-12-01 10:58:55.000000000 +0100
+++ linux-2.6-dev/drivers/usb/host/m82xx-hcd.h 2005-11-22 11:07:44.000000000 +0100
@@ -16,6 +16,9 @@
* (C) Copyright 2000 Embedded Planet
* http://www.embeddedplanet.com
*
+ * Fixes for MPC8270/80
+ * Hans Schillstrom <hans.schillstrom@pwav.com>
+ *
*/
#ifndef M82XXHCI_H
@@ -42,9 +45,21 @@
#endif
#ifdef CONFIG_CPM2
+
+#ifdef CONFIG_RCB8270
+# ifndef CONFIG_MPC8270
+# define CONFIG_MPC8270 1
+# endif
+#endif
+
+#if defined(CONFIG_MPC8270) || defined(CONFIG_MPC8280)
+#define USB_SCC_IDX 3 /* SCC4 */
+#define CPMVEC_USB (CPM_IRQ_OFFSET + CPMVEC_SCC4)
+#else
#define USB_SCC_IDX 2 /* SCC3 */
#define CPMVEC_USB (CPM_IRQ_OFFSET + CPMVEC_SCC3)
#endif
+#endif
#define BD_USB_TC ((ushort)0x0400) /* transmit crc after last */
#define BD_USB_CNF ((ushort)0x0200) /* wait for handshake */
@@ -238,6 +253,41 @@
#endif
#ifdef CONFIG_CPM2
+/* Clock source setting */
+#define USB_CMX_SCR_MASK ((uint)(0xff000000 >> (USB_SCC_IDX<<3)))
+#define USB_CMX_CLK5 ((uint)((CMXSCR_RS1CS_CLK11 | CMXSCR_TS1CS_CLK11) >> (USB_SCC_IDX<<3)))
+#define USB_CMX_CLK6 ((uint)((CMXSCR_RS1CS_CLK12 | CMXSCR_TS1CS_CLK12) >> (USB_SCC_IDX<<3)))
+#define USB_CMX_CLK7 ((uint)((CMXSCR_RS1CS_CLK3 | CMXSCR_TS1CS_CLK3) >> (USB_SCC_IDX<<3)))
+#define USB_CMX_CLK8 ((uint)((CMXSCR_RS1CS_CLK4 | CMXSCR_TS1CS_CLK4) >> (USB_SCC_IDX<<3)))
+
+#define PC_CLK5_48MHz ((uint)(1 << (31 - 27)))
+#define PC_CLK6_48MHz ((uint)(1 << (31 - 26)))
+#define PC_CLK7_48MHz ((uint)(1 << (31 - 25)))
+#define PC_CLK8_48MHz ((uint)(1 << (31 - 24)))
+
+#if defined(CONFIG_MPC8270) || defined(CONFIG_MPC8280)
+
+/* bits in parallel i/o port registers that have to be cleared to */
+/* configure the pins for SCC4 USB use. */
+ /* sor dir */
+ /* --- --- */
+#define PD_USB_RXD ((uint)(1 << (31 - 22))) /* 0 0 */
+#define PD_USB_TN ((uint)(1 << (31 - 21))) /* 0 1 */
+#define PD_USB_TP ((uint)(1 << (31 - 20))) /* 0 1 */
+
+#define PD_MSK (PD_USB_RXD | PD_USB_TN | PD_USB_TP)
+#define PD_DIR0 PD_USB_RXD
+#define PD_DIR1 (PD_USB_TN | PD_USB_TP)
+
+#define PC_USB_OE ((uint)(1 << (31 - 20))) /* 0 1 */
+#define PC_USB_RP ((uint)(1 << (31 - 9))) /* 0 0 */
+#define PC_USB_RN ((uint)(1 << (31 - 8))) /* 0 0 */
+
+#define PC_MSK (PC_USB_OE | PC_USB_RP | PC_USB_RN)
+#define PC_DIR0 (PC_USB_RP | PC_USB_RN)
+#define PC_DIR1 PC_USB_OE
+
+#else
/* bits in parallel i/o port registers that have to be cleared to */
/* configure the pins for SCC1 USB use. */
@@ -259,8 +309,7 @@
#define PC_DIR0 (PC_USB_RP | PC_USB_RN)
#define PC_DIR1 PC_USB_OE
-#define PC_CLK6_48MHz ((uint)(1 << (31 - 26))) /* 0 0 */
-#define PC_CLK8_48MHz ((uint)(1 << (31 - 24))) /* 0 0 */
+#endif
#endif
@@ -409,7 +458,9 @@
USB_CLOCK_PA6_CLK2,
USB_CLOCK_BRG3,
USB_CLOCK_BRG4,
+ USB_CLOCK_PC27_CLK5,
USB_CLOCK_PC26_CLK6,
+ USB_CLOCK_PC25_CLK7,
USB_CLOCK_PC24_CLK8,
USB_CLOCK_CNT,
};
^ permalink raw reply
* Re: [PATCH] ppc32: 8xx board-specific platform stuff for fs_enet
From: Marcelo Tosatti @ 2005-12-01 12:17 UTC (permalink / raw)
To: Kumar Gala; +Cc: linuxppc-embedded list, Paul Mackerras
In-Reply-To: <6B29BC5F-3B18-4EEE-B70C-215A2C540C85@kernel.crashing.org>
On Wed, Nov 30, 2005 at 01:08:31AM -0600, Kumar Gala wrote:
> >Hi Kumar,
> >
> >I dont really know the policy for driver placement, but it seems that
> >it works on a case by case basis.
> >
> >The files in arch/ppc/8xx_io/ (which is what I think you refer to as
> >candidates for drivers/), are:
>
> We have been slowly working on moving drivers out of arch/ppc and
> into drivers/ so that subsystem maintainers could get proper review
> of them.
>
> >1) commproc.c
> >Basic API for dpram access. Core code.
> >
> >2) micropatch.c
> >microcode update code/data. Core code.
>
> Well #1 & #2 aren't what I would call drivers at all. I would
> consider them syslib/ candidates. Hopefully, someone will
Move them there? Yeah... We can add that to the 8xx TODO list
if its interesting.
> >3) cs4218.h
> >4) cs4218_tdm.c
> >
> >cs4218 does not compile at the moment due to syntatical problems,
> >I've fixed them up and the driver compiles, but I don't know
> >if it works (patch attached).
> >
> >I would not be surprised if the driver has been broken since
> >long time ago.
> >
> >Does anyone have hardware to test it? Dan?
> >
> >Otherwise we should remove it from the tree, since its unmaintained
> >and unused.
>
> If its still good, I would guessing /drivers/audio or snd, but
> neither seem to exist. I wondering where sound card drivers live
> these days.
snd/ I think... Someone needs to test the driver. I think we should just
fixup the syntactical problems and mark it as BROKEN until someone (Dan?)
confirms it works.
> >5) enet.c
> >6) fec.c
> >
> >The ENET/FEC network drivers are obseleted by fs_enet.
> >
> >However there are some PHY descriptions in fec.c which are missing
> >from
> >fs_enet - we'd better make sure to have them all in the new driver
> >before removing the old one.
>
> Agreed.
>
> >Aris, would you mind looking into this?
> >
> >Once we have that we can set a deadline at Documentation/feature-
> >removal.txt
> >if desired.
> >
> >Other than those there are no 8xx drivers in arch/ppc/ AFAIK.
> >
> ><cs42.patch>
>
> Good deal. Are we really removing anything (except maybe cs4218)?
FEC certainly and cs4218 seems like a candidate.
Thanks for your comments!
^ permalink raw reply
* Re: Linux hangs while Uncompressing
From: Mark Chambers @ 2005-12-01 12:04 UTC (permalink / raw)
To: linuxppc-embedded, pritha.bhattacharya
In-Reply-To: <OF0098DF7F.857DE409-ON652570CA.001AA3F7-652570CA.0036DB32@tcs.com>
[-- Attachment #1: Type: text/plain, Size: 995 bytes --]
Hi All,
I have RAM version of U-Boot which is running on a board similar to MPC8260. My memory map isas follows:
Staring address Device Size Memory controller and CS
0000 0000
0800 0000
FFF0 0000
0F00 0000
3000 0000
3800 0000
4200 0000
5000 0000 FLASH (Boot)
FLASH (Code)
SSRAM
CPU internal registers
SDRAM
SDRAM
Framer
DSP 8102 1MB (512Kx16)
4 MB (1Mx16)
2 MB (512Kx36)
128 KB
128 MB (16Mx72)
128 MB (16Mx72)
1 MB
2 MB BR0/OR0: CS0
BR1/OR1: CS1
BR2/OR2: CS2
BR3/OR3: CS3
BR4/OR4: CS4
BR5/OR5: CS5
BR6/OR6: CS6
This configuration will not work for linux. Linux needs to run in SDRAM starting at zero (notice
'Load Address' and 'Entry Point' just before 'uncompressing image'.)
Mark Chambers
[-- Attachment #2: Type: text/html, Size: 3313 bytes --]
^ permalink raw reply
* RE: Linux hangs while Uncompressing
From: KS Soumya-ask067 @ 2005-12-01 11:52 UTC (permalink / raw)
To: linuxppc-embedded
Hi Pritha,
These are the few things that you might want to look for.
1) Check for the command line argument which is being passed to the =
kernel, if that is alright. (I mean to say set the console options to =
the kernel)
Something which looks like
setenv bootargs=3D/dev/(nfs/ram???) rw console=3D(ttyS?),baudrate
2) Try to enable "early debug messages" options in the kernel if =
available to debug more.
Hope this helps a bit.
-Soumya
=09
-----Original Message-----
From: linuxppc-embedded-bounces@ozlabs.org =
[mailto:linuxppc-embedded-bounces@ozlabs.org] On Behalf Of =
linuxppc-embedded-request@ozlabs.org
Sent: Thursday, December 01, 2005 5:02 PM
To: linuxppc-embedded@ozlabs.org
Subject: Linuxppc-embedded Digest, Vol 16, Issue 3
Send Linuxppc-embedded mailing list submissions to
linuxppc-embedded@ozlabs.org
To subscribe or unsubscribe via the World Wide Web, visit
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
or, via email, send a message with subject or body 'help' to
linuxppc-embedded-request@ozlabs.org
You can reach the person managing the list at
linuxppc-embedded-owner@ozlabs.org
When replying, please edit your Subject line so it is more specific than =
"Re: Contents of Linuxppc-embedded digest..."
Today's Topics:
1. Re: Xilinx_uartlite (T Ziomek)
2. Re:RE: linuxppc-embedded help needed:kernel access of bad
area (zengshuai@sogou.com)
3. RE: Xilinx_uartlite (Jaap de Jong)
4. Re: [PATCH] ibm_emac: fix graceful stop timeout handling
(Jeff Garzik)
5. AW: RE: linuxppc-embedded help needed:kernel access of bad
area (Achim Machura)
6. bus error (zengshuai@sogou.com)
7. porting linux to new board type (Nathael PAJANI)
8. Linux hangs while Uncompressing (pritha.bhattacharya@tcs.com)
----------------------------------------------------------------------
Message: 1
Date: Wed, 30 Nov 2005 19:06:29 -0600 (Central Standard Time)
From: T Ziomek <ctz001@email.mot.com>
Subject: Re: Xilinx_uartlite
To: jaap.dejong@nedap.com, linuxppc-embedded
<linuxppc-embedded@ozlabs.org>
Message-ID: <Pine.WNT.4.61.0511301902100.3620@holyoke.labs.mot.com>
Content-Type: TEXT/PLAIN; charset=3DUS-ASCII; format=3Dflowed
> I'm trying to get my avnet virtex4fx12 running with linux.
> It boots, but ends with:
> Warning: unable to open an initial console.
> This means /dev/console was not opened; init is running.
> Since my board has no 16550 uart I must use xilinx_uartlite Part of my =
> configuration:
> +--Character devices
> +--Xilinx UART Lite ON
> +--Console on UART Lite port ON
> Any ideas?
/dev/console may not be tied to your UARTLite. If you don't specify the =
console on your kernel command line, try adding something along the =
lines of "console=3DttyS0,19200" to it (with the appropriate device and =
baud rate of course).
Tom
--=20
/"\ ASCII Ribbon Campaign |
\ / | Email to user 'CTZ001'
X Against HTML | at 'email.mot.com'
/ \ in e-mail & news |
------------------------------
Message: 2
Date: Thu, 1 Dec 2005 14:52:01 +0800 (CST)
From: <zengshuai@sogou.com>
Subject: Re:RE: linuxppc-embedded help needed:kernel access of bad
area
To: "Fillod Stephane" <stephane.fillod@thomson.net>
Cc: Linuxppc-embedded@ozlabs.org
Message-ID: <5100380.1133419921433.JavaMail.postfix@mx3.mail.sohu.com>
Content-Type: text/plain; charset=3D"ISO-8859-1"
thanks very much.but i'm not going to write a user space program.
this is the detail:
//led-module.c
#ifndef __KERNEL__
#define __KERNEL__
#endif
#ifndef MODULE
#define MODULE
#endif
#include <linux/config.h>
#include <linux/module.h>
MODULE_LICENSE("GPL");
#ifdef CONFIG_SMP
#define __SMP__
#endif
#define CONFIG_TASK_SIZE 0x80000000 =20
#include <asm/processor.h>
#include <linux/init.h>
#include <asm/uaccess.h> /* copy_to_user(), copy_from_user() */ #include =
<linux/fs.h> /* struct file_operations, register_chrdev(), ... */ =
#include <linux/kernel.h> /* printk()*/ #include <linux/sched.h>=20
#include "led-module.h"
#define BCSRADDR 0x04500000
static int PQ2FADS_GPL_open (struct inode *inode, struct file *filp); =
static ssize_t PQ2FADS_GPL_read (struct file *filp, char *buf, size_t =
count,loff_t *f_pos); static ssize_t PQ2FADS_GPL_write (struct file =
*filp, const char *buf, size_t count,loff_t *f_pos); static int =
PQ2FADS_GPL_ioctl (struct inode *inode,struct file *filp,unsigned int =
cmd,unsigned long scmd); static int PQ2FADS_GPL_release (struct inode =
*inode, struct file *filp);
struct file_operations PQ2FADS_GPL_fops =3D {
open: PQ2FADS_GPL_open,
release: PQ2FADS_GPL_release,
ioctl: PQ2FADS_GPL_ioctl,
read: PQ2FADS_GPL_read,
write: PQ2FADS_GPL_write,
};
static int PQ2FADS_GPL_major;
static int PQ2FADS_GPL_state;
static volatile PQ2FADS_BCSR *PQ2FADS_GPL_CSR=3D0;
static int init_module(void)
{
printk ("This' a PQ2FADS_ZU board GPL LED Device File!\n");
PQ2FADS_GPL_major =3D register_chrdev (0, "GPL LED Device", =
&PQ2FADS_GPL_fops);=20
if (PQ2FADS_GPL_major < 0)=20
{
printk("error1");
return PQ2FADS_GPL_major;
}=20
printk ("The major is:%d\n", PQ2FADS_GPL_major);=20
return 0;
}
static void cleanup_module(void)
{
unregister_chrdev(PQ2FADS_GPL_major, "GPL LED Device");
printk("PQ2FADS_ZU board GPL LED Device has been removed! bye!\n"); }
static int PQ2FADS_GPL_open(struct inode *inode,struct file *filp) {
PQ2FADS_GPL_CSR=3D(PQ2FADS_BCSR*)BCSRADDR;
printk("open %s...OK!\n ", current->comm);
return 0;
}
static int PQ2FADS_GPL_release(struct inode *inode,struct file *filp) {
printk("close....OK!\n ");
return 0;
}
static ssize_t PQ2FADS_GPL_read(struct file *filp,char *buf,size_t =
count,loff_t *f_pos) {
// char ledopen[20]=3D"led is open.";
// char ledclose[20]=3D"led is close.";
// count=3D20;
if(((PQ2FADS_GPL_CSR->bcsr0) & 0x02000000) =3D=3D 0x0) printk("led is =
open");
// else copy_to_user(buf,ledclose,20);
return count;
}
static ssize_t PQ2FADS_GPL_write(struct file *filp,const char =
*buf,size_t count,loff_t *f_pos) {
PQ2FADS_GPL_CSR->bcsr0 |=3D0x02000000;
return 0;
}
static int PQ2FADS_GPL_ioctl(struct inode *inode,struct file =
*filp,unsigned int cmd,unsigned long scmd) {
return 0;
}
//led-app.c
#include <stdio.h>
int main(void)
{
int mydev,err;
char resultchar[20]=3D"begin...";
mydev=3Dopen("/dev/PQ2FADS_GPL","rb+");
if(mydev<0)
{
printf("open error.\n");
return 1;
}
=09
err=3Dread(mydev,resultchar,20);
if(err !=3D20) printf("read1 error!\n");
printf("read1=3D%s",resultchar);
err=3Dwrite(mydev,resultchar,20);
if(err !=3D0) printf("write error!\n");
err=3Dread(mydev,resultchar,20);
if(err !=3D20) printf("read2 error!\n");
printf("read2=3D%s",resultchar);
return 0;
}
i got led-module.o and led-app.exe
i insmod led-module.o =20
mknod /dev/PQ2FADS_GPL
and when i run led-app.exe
show:
# ./led-app.exe
open led-app.exe...OK!
Oops: kernel access of bad area, sig: 11
NIP: C30B11B4 XER: 00000000 LR: C003A310 SP: C06B1F00 REGS: c06b1e50 =
TRAP: 0300
Not tainted
MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
DAR: 04500000, DSISR: 20000000
TASK =3D c06b0000[201] 'led-app.exe' Last syscall: 3 last math c06b0000 =
last altivec 00000000
GPR00: C003A310 C06B1F00 C06B0000 C01A5AA0 7FFFFDE0 00000014 C01A5AC0 =
00000000
GPR08: 00000000 04500000 0000000C C01A0000 30025CE8 10018B5C 00000000 =
00000000
GPR16: 00000000 00000000 00000000 00000000 00009032 006B1F40 00000000 =
C0003E88
GPR24: C0003BE0 00000001 10000500 7FFFFEA4 7FFFFDE0 FFFFFFEA C01A5AA0 =
00000014 Call backtrace:
10000A1C C003A310 C0003C3C 100004AC 0FEC6D74 00000000 Segmentation fault =
# as you know,i am really a new gay.help me please.
----- Original Message -----
From: Fillod Stephane
To: zengshuai@sogou.com ;ppc
Subject: RE: linuxppc-embedded help needed:kernel access of bad area
Sent: Wed Nov 30 17:33:25 CST 2005
> Dear zengshuai,
>=20
> zengshuai@sogou.com wrote:
> > i writed a led driver for PQ2FADS(a ppc board).
> > but i can't read/write 0x04500000 where led register addr locate in.
> > i tested two ways to do that.
> > first,
> > p=3D0x04500000;
> > *p=3D0x12;
> > ....
> > second,
> > outb(0x12,0x04500000);
> > ...
> > two ways both didn't work.they had a some wrong:kernel access of bad
> area.
> > how can i know which area is bad area or good area?
> > and what can i do next? thanks.
>=20
> Do yourself a favor, read a book about Linux device driver=20
> development, for example one listed[1] in the excellent Denx's DLUG =
FAQ[2].
> Getting some training on PowerPC development is a good idea too.
> [1] http://www.denx.de/wiki/view/DULG/MoreInformationBooks
> [2] http://www.denx.de/wiki/DULG/Manual
>=20
> Peruse also your chip data-sheet, and you will see that outb() is=20
> non-sense.
>=20
> If you are accessing the led register from kernel space, you'll find a =
> solution using ioremap(). Otherwise, if you are accessing the led=20
> register from user space, this link[3] will help you, or this shorter=20
> one[4].
> You can follow this thread[5] for more information.
>=20
> [3]
> http://www.denx.de/twiki/bin/view/PPCEmbedded/DeviceDrivers#Section_Ac
> ce
> ssingPeripheralsFromUserSpace
> [4] http://tinyurl.com/6c7th
> [5] http://lists.linuxppc.org/linuxppc-embedded/200403/msg00059.html
>=20
> Please next time, do ourselves a favor, try some searching first=20
> (google, whatever). Your question is a FAQ.
>=20
> Regards,
> --
> Stephane
>=20
------------------------------
?????Sogou.com?2G??????????!=20
http://mail.sogou.com/recommend/sogoumail_invite_reg1.jsp?from=3Dsogouinv=
itation&s_EMAIL=3Dzengshuai%40sogou.com&username=3D&FullName=3D&Email=3D&=
verify=3De197bd6dbd1fc7f8d6a035729df08d63
------------------------------
Message: 3
Date: Thu, 1 Dec 2005 08:13:11 +0100
From: "Jaap de Jong" <jaap.dejong@nedap.com>
Subject: RE: Xilinx_uartlite
To: "T Ziomek" <ctz001@email.mot.com>, "linuxppc-embedded"
<linuxppc-embedded@ozlabs.org>
Message-ID:
<6915D0AE8B9047438F320B466AE30FDD324CCD@nvs0003.nedap.local>
Content-Type: text/plain; charset=3D"us-ascii"
Hi Tom,
Thanks for your reply, but then I only get:
Now booting the kernel
Beste regards,
Jaap
-----Oorspronkelijk bericht-----
Van: T Ziomek [mailto:ctz001@email.mot.com]=20
Verzonden: donderdag 1 december 2005 02:06
Aan: Jaap de Jong; linuxppc-embedded
Onderwerp: Re: Xilinx_uartlite
> I'm trying to get my avnet virtex4fx12 running with linux.
> It boots, but ends with:
> Warning: unable to open an initial console.
> This means /dev/console was not opened; init is running.
> Since my board has no 16550 uart I must use xilinx_uartlite Part of my
> configuration:
> +--Character devices
> +--Xilinx UART Lite ON
> +--Console on UART Lite port ON
> Any ideas?
/dev/console may not be tied to your UARTLite. If you don't specify the
console on your kernel command line, try adding something along the
lines of "console=3DttyS0,19200" to it (with the appropriate device and
baud rate of course).
Tom
--=20
/"\ ASCII Ribbon Campaign |
\ / | Email to user 'CTZ001'
X Against HTML | at 'email.mot.com'
/ \ in e-mail & news |
------------------------------
Message: 4
Date: Thu, 01 Dec 2005 02:23:42 -0500
From: Jeff Garzik <jgarzik@pobox.com>
Subject: Re: [PATCH] ibm_emac: fix graceful stop timeout handling
To: Eugene Surovegin <ebs@ebshome.net>
Cc: netdev@vger.kernel.org, linuxppc-embedded@ozlabs.org
Message-ID: <438EA4FE.8010903@pobox.com>
Content-Type: text/plain; charset=3DISO-8859-1; format=3Dflowed
applied
------------------------------
Message: 5
Date: Thu, 1 Dec 2005 09:00:41 +0100
From: "Achim Machura" <achim.machura@berghof.com>
Subject: AW: RE: linuxppc-embedded help needed:kernel access of bad
area
To: <zengshuai@sogou.com>
Cc: "Linuxppc-Embedded \(E-Mail\)" <linuxppc-embedded@ozlabs.org>
Message-ID: <000001c5f64d$538113d0$34f1ff0a@beint.local>
Content-Type: text/plain; charset=3D"iso-8859-1"
Hello,
> #define BCSRADDR 0x04500000
>=20
...
> static int PQ2FADS_GPL_open(struct inode *inode,struct file *filp)
> {
> PQ2FADS_GPL_CSR=3D(PQ2FADS_BCSR*)BCSRADDR;
possible you have to change physical address to logical see ioremap.
achim
------------------------------
Message: 6
Date: Thu, 1 Dec 2005 16:37:43 +0800 (CST)
From: <zengshuai@sogou.com>
Subject: bus error
To: "ppc" <linuxppc-embedded@ozlabs.org>
Message-ID:
<13090422.1133426263198.JavaMail.postfix@mx3.mail.sohu.com>
Content-Type: text/plain; charset=3D"GB2312"
//test.c
#include <stdio.h>
#include <stdlib.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <unistd.h>
#include <sys/mman.h>
int main(void)
{
static volatile char *reg_mem;
static int axs_mem_fd =3D -1;
axs_mem_fd =3D open("/dev/mem", O_RDWR|O_SYNC);
if (axs_mem_fd < 0) {
perror("AXS: can't open /dev/mem");
return NULL;
}
/* memory map */
reg_mem =3D(volatile char*)mmap(
(caddr_t)reg_mem,
0x4,
PROT_READ|PROT_WRITE,
MAP_SHARED,
axs_mem_fd,
0x04600000
);
if(reg_mem[0]=3D=3D0x10) printf("OK");
else printf("sorry");
}
host:
ppc_6xx-gcc -o test test.c
target:
./test
Bus error
need help,thanks
------------------------------
=CE=D2=CF=D6=D4=DA=CA=B9=D3=C3Sogou.com=B5=C42G=D3=CA=CF=E4=C1=CB=A3=AC=C4=
=E3=D2=B2=C0=B4=CA=D4=CA=D4=B0=C9!=20
http://mail.sogou.com/recommend/sogoumail_invite_reg1.jsp?from=3Dsogouinv=
itation&s_EMAIL=3Dzengshuai%40sogou.com&username=3Dlinuxppc-embedded&Full=
Name=3Dlinuxppc-embedded&Email=3Dlinuxppc-embedded%40ozlabs.org&verify=3D=
755eff4e640bdcfc57d93cbd8b0a9cb7
------------------------------
Message: 7
Date: Thu, 01 Dec 2005 12:30:54 +0100
From: Nathael PAJANI <nathael.pajani@cpe.fr>
Subject: porting linux to new board type
To: linuxppc-embedded@ozlabs.org
Message-ID: <438EDEEE.2000000@cpe.fr>
Content-Type: text/plain; charset=3DISO-8859-1; format=3Dflowed
Hi!
I stepped over your message without noticing, do you still need help?
I do not have much experience yet, as I've been graduated only two month =
ago, but my job actualy is porting linux to custom boards, and I=20
achieved my first one two weeks ago.
So maybe I can hand out some usefull clues.
Have fun :)
+++
------------------------------
Message: 8
Date: Thu, 1 Dec 2005 15:29:10 +0530
From: pritha.bhattacharya@tcs.com
Subject: Linux hangs while Uncompressing
To: linuxppc-embedded <linuxppc-embedded@ozlabs.org>
Message-ID:
<OF0098DF7F.857DE409-ON652570CA.001AA3F7-652570CA.0036DB32@tcs.com>
Content-Type: text/plain; charset=3D"us-ascii"
Hi All,
I have RAM version of U-Boot which is running on a board similar to=20
MPC8260. My memory map isas follows:
Staring address Device Size Memory=20
controller and CS
0000 0000
0800 0000
FFF0 0000
0F00 0000
3000 0000
3800 0000
4200 0000
5000 0000
FLASH (Boot)
FLASH (Code)
SSRAM
CPU internal registers
SDRAM
SDRAM
Framer
DSP 8102
1MB (512Kx16)
4 MB (1Mx16)
2 MB (512Kx36)
128 KB
128 MB (16Mx72)
128 MB (16Mx72)
1 MB
2 MB
BR0/OR0: CS0
BR1/OR1: CS1
BR2/OR2: CS2
BR3/OR3: CS3
BR4/OR4: CS4
BR5/OR5: CS5
BR6/OR6: CS6
I have downloaded Linux 2.4.25 kernel image through kermit. after=20
downloading the image in SDRAM location 0x30000000 and giving the =
command=20
bootm 0x30000000
the prompt shows a message:
TCS-PIC-UBOOT=3D> loadb 0x30000000## Ready for binary (kermit) download =
to=20
0x30000000 at 57600 bps...
## Total Size =3D 0x000936f6 =3D 603894 Bytes
## Start Addr =3D 0x30000000
TCS-PIC-UBOOT=3D> bootm 0x30000000## Booting image at 30000000 ...
Image Name: Linux-2.4.25
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 603830 Bytes =3D 589.7 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ...=20
The system hangs here and is not able to uncompress the kernel any=20
further. I have checked in the FAQs provided in the denx's site, but =
could=20
not find anything similar to my case.
I would appreciate any help.
Thanks & Regards,
Pritha Bhattacharya
Tata Consultancy Services Limited
Mailto: pritha.bhattacharya@tcs.com
Website: http://www.tcs.com
Notice: The information contained in this e-mail message and/or =
attachments to it may contain confidential or privileged information. =
If you are not the intended recipient, any dissemination, use, review, =
distribution, printing or copying of the information contained in this =
e-mail message and/or attachments to it are strictly prohibited. If =
you have received this communication in error, please notify us by reply =
e-mail or telephone and immediately and permanently delete the message =
and any attachments. Thank you
-------------- next part --------------
An HTML attachment was scrubbed...
URL: =
http://ozlabs.org/pipermail/linuxppc-embedded/attachments/20051201/f2efec=
47/attachment.htm
------------------------------
_______________________________________________
Linuxppc-embedded mailing list
Linuxppc-embedded@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
End of Linuxppc-embedded Digest, Vol 16, Issue 3
************************************************
^ permalink raw reply
* 8560 SCC uart driver
From: kiran kumar @ 2005-12-01 11:45 UTC (permalink / raw)
To: linuxppc-embedded
[-- Attachment #1: Type: text/plain, Size: 361 bytes --]
Hi all,
It is required to configure one of the SCC of MPC8560 as complete UART and analog modem to be interfaced. Is driver already available in this regard or let me know how to proceed further.
Thanks in advance.
Regards,
Kiran
---------------------------------
Yahoo! Music Unlimited - Access over 1 million songs. Try it free.
[-- Attachment #2: Type: text/html, Size: 592 bytes --]
^ permalink raw reply
* Linux hangs while Uncompressing
From: pritha.bhattacharya @ 2005-12-01 9:59 UTC (permalink / raw)
To: linuxppc-embedded
[-- Attachment #1: Type: text/plain, Size: 2114 bytes --]
Hi All,
I have RAM version of U-Boot which is running on a board similar to
MPC8260. My memory map isas follows:
Staring address Device Size Memory
controller and CS
0000 0000
0800 0000
FFF0 0000
0F00 0000
3000 0000
3800 0000
4200 0000
5000 0000
FLASH (Boot)
FLASH (Code)
SSRAM
CPU internal registers
SDRAM
SDRAM
Framer
DSP 8102
1MB (512Kx16)
4 MB (1Mx16)
2 MB (512Kx36)
128 KB
128 MB (16Mx72)
128 MB (16Mx72)
1 MB
2 MB
BR0/OR0: CS0
BR1/OR1: CS1
BR2/OR2: CS2
BR3/OR3: CS3
BR4/OR4: CS4
BR5/OR5: CS5
BR6/OR6: CS6
I have downloaded Linux 2.4.25 kernel image through kermit. after
downloading the image in SDRAM location 0x30000000 and giving the command
bootm 0x30000000
the prompt shows a message:
TCS-PIC-UBOOT=> loadb 0x30000000## Ready for binary (kermit) download to
0x30000000 at 57600 bps...
## Total Size = 0x000936f6 = 603894 Bytes
## Start Addr = 0x30000000
TCS-PIC-UBOOT=> bootm 0x30000000## Booting image at 30000000 ...
Image Name: Linux-2.4.25
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 603830 Bytes = 589.7 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ...
The system hangs here and is not able to uncompress the kernel any
further. I have checked in the FAQs provided in the denx's site, but could
not find anything similar to my case.
I would appreciate any help.
Thanks & Regards,
Pritha Bhattacharya
Tata Consultancy Services Limited
Mailto: pritha.bhattacharya@tcs.com
Website: http://www.tcs.com
Notice: The information contained in this e-mail message and/or attachments to it may contain confidential or privileged information. If you are not the intended recipient, any dissemination, use, review, distribution, printing or copying of the information contained in this e-mail message and/or attachments to it are strictly prohibited. If you have received this communication in error, please notify us by reply e-mail or telephone and immediately and permanently delete the message and any attachments. Thank you
[-- Attachment #2: Type: text/html, Size: 4968 bytes --]
^ permalink raw reply
* porting linux to new board type
From: Nathael PAJANI @ 2005-12-01 11:30 UTC (permalink / raw)
To: linuxppc-embedded
Hi!
I stepped over your message without noticing, do you still need help?
I do not have much experience yet, as I've been graduated only two month
ago, but my job actualy is porting linux to custom boards, and I
achieved my first one two weeks ago.
So maybe I can hand out some usefull clues.
Have fun :)
+++
^ permalink raw reply
* bus error
From: zengshuai @ 2005-12-01 8:37 UTC (permalink / raw)
To: ppc
//test.c
#include <stdio.h>
#include <stdlib.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <unistd.h>
#include <sys/mman.h>
int main(void)
{
static volatile char *reg_mem;
static int axs_mem_fd = -1;
axs_mem_fd = open("/dev/mem", O_RDWR|O_SYNC);
if (axs_mem_fd < 0) {
perror("AXS: can't open /dev/mem");
return NULL;
}
/* memory map */
reg_mem =(volatile char*)mmap(
(caddr_t)reg_mem,
0x4,
PROT_READ|PROT_WRITE,
MAP_SHARED,
axs_mem_fd,
0x04600000
);
if(reg_mem[0]==0x10) printf("OK");
else printf("sorry");
}
host:
ppc_6xx-gcc -o test test.c
target:
./test
Bus error
need help,thanks
------------------------------
我现在使用Sogou.com的2G邮箱了，你也来试试吧!
http://mail.sogou.com/recommend/sogoumail_invite_reg1.jsp?from=sogouinvitation&s_EMAIL=zengshuai%40sogou.com&username=linuxppc-embedded&FullName=linuxppc-embedded&Email=linuxppc-embedded%40ozlabs.org&verify=755eff4e640bdcfc57d93cbd8b0a9cb7
^ permalink raw reply
* AW: RE: linuxppc-embedded help needed:kernel access of bad area
From: Achim Machura @ 2005-12-01 8:00 UTC (permalink / raw)
To: zengshuai; +Cc: Linuxppc-Embedded (E-Mail)
In-Reply-To: <5100380.1133419921433.JavaMail.postfix@mx3.mail.sohu.com>
Hello,
> #define BCSRADDR 0x04500000
>
...
> static int PQ2FADS_GPL_open(struct inode *inode,struct file *filp)
> {
> PQ2FADS_GPL_CSR=(PQ2FADS_BCSR*)BCSRADDR;
possible you have to change physical address to logical see ioremap.
achim
^ permalink raw reply
* Re: [PATCH] ibm_emac: fix graceful stop timeout handling
From: Jeff Garzik @ 2005-12-01 7:23 UTC (permalink / raw)
To: Eugene Surovegin; +Cc: netdev, linuxppc-embedded
In-Reply-To: <20051124224840.GB21929@gate.ebshome.net>
applied
^ permalink raw reply
* RE: Xilinx_uartlite
From: Jaap de Jong @ 2005-12-01 7:13 UTC (permalink / raw)
To: T Ziomek, linuxppc-embedded
Hi Tom,
Thanks for your reply, but then I only get:
Now booting the kernel
Beste regards,
Jaap
-----Oorspronkelijk bericht-----
Van: T Ziomek [mailto:ctz001@email.mot.com]=20
Verzonden: donderdag 1 december 2005 02:06
Aan: Jaap de Jong; linuxppc-embedded
Onderwerp: Re: Xilinx_uartlite
> I'm trying to get my avnet virtex4fx12 running with linux.
> It boots, but ends with:
> Warning: unable to open an initial console.
> This means /dev/console was not opened; init is running.
> Since my board has no 16550 uart I must use xilinx_uartlite Part of my
> configuration:
> +--Character devices
> +--Xilinx UART Lite ON
> +--Console on UART Lite port ON
> Any ideas?
/dev/console may not be tied to your UARTLite. If you don't specify the
console on your kernel command line, try adding something along the
lines of "console=3DttyS0,19200" to it (with the appropriate device and
baud rate of course).
Tom
--=20
/"\ ASCII Ribbon Campaign |
\ / | Email to user 'CTZ001'
X Against HTML | at 'email.mot.com'
/ \ in e-mail & news |
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox