* Re: Which CAN driver to port to for PPC
From: Robert Schwebel @ 2005-12-29 13:43 UTC (permalink / raw)
To: Andrey Volkov
Cc: David Jander, urs.thuermann, socket-can, oliver.hartkopp,
linuxppc-embedded
In-Reply-To: <43B2A902.3090008@varma-el.com>
Hi,
On Wed, Dec 28, 2005 at 06:02:26PM +0300, Andrey Volkov wrote:
> Robert Schwebel et al have worked socket based CAN (i.e. implement CAN
> as _net_ dev, not as char), as consequence you will not have problem
> with major/minor numbers, duplicated code in drivers for different
> chips, could share CAN dev between diff processes _without_ misc.
> third party shared libraies, stacked CAN protocols (CANopen/NMEA2000
> could be abstract kernel module)... But currently it is not open for
> everyone (due to beta status, AFAIK)
>
> Alessandro, please check Pengutronix work first, may be it will be
> helpfull to you to
>
> [...]
>
> P.S. Robert, when I check last time, it was mature enogh, so may be time
> to open mail-list and svn?
The socket-can stuff is mature enouth to have been used in some projects
at Pengutronix.
In december, we have made a synchronisation meeting with the VW people
who made the initial port for 2.4; they are more focussed on having
higher level transport protocols ontop of the "raw" socket interface we
currently use. During that process we have reviewed the user interface
with regard to their use cases, so it will have to be changed a little
bit before we have something which is in a state to be posted on lkml.
Unfortunately we have no commercial project behind the infrastructure
work, so it's priority is lower than it should be to really drive things
forward (paying customers have a higher priority than community work).
Robert
--
Dipl.-Ing. Robert Schwebel | http://www.pengutronix.de
Pengutronix - Linux Solutions for Science and Industry
Handelsregister: Amtsgericht Hildesheim, HRA 2686
Hannoversche Str. 2, 31134 Hildesheim, Germany
Phone: +49-5121-206917-0 | Fax: +49-5121-206917-9
^ permalink raw reply
* Re : MPC8347 USB problem : Copying big file[>150MB] discontinuous via Samba
From: Sam Song @ 2005-12-29 12:54 UTC (permalink / raw)
To: linuxppc-embedded list
In-Reply-To: <20051229043720.15530.qmail@web15809.mail.cnb.yahoo.com>
Sam Song <samlinuxppc@yahoo.com.cn> wrote:
> Hi all,
>
> We met a USB performance problem on a custom
> 8347board with 2.4.31. When copying small
> files no more than 100MB in size, it worked
> smoothly with NEC or VIA PCI card. But
> copying a big file like more than 150MB
> in size would decrease the copying
> speed a lot. Serial console even couldn't
> response 'ls' command. The target has a
> 128MB DDR RAM.
Ummm, actually, 256MB DDR RAM.
> While the same driver with 2.4.31 worked fine
> on a 8248 custom board. What could the
> problem be?
Arhhhh, it was due to USB 1.1 limitation
itself(8347 USB 2.0 driver wasn't added
yet when I posted it). Only on the
workable 8248 target with USB 1.1 driver,
it would have such a phenomena. There was
even a network error displayed. If working
with USB 2.0, no any problem. New to me:-)
But Well, I don't have the guts
to say this is a kernel's bug:-)
> Sorry to distrub you during Christmas Time.
OK, stay on relax, pls.
Best regards,
Sam
__________________________________________________
赶快注册雅虎超大容量免费邮箱?
http://cn.mail.yahoo.com
^ permalink raw reply
* Re: Which CAN driver to port to for PPC
From: Wolfgang Grandegger @ 2005-12-29 12:17 UTC (permalink / raw)
To: Alessandro Rubini
Cc: david.jander, r.schwebel, socket-can, Jan Kiszka,
linuxppc-embedded
In-Reply-To: <20051228150742.GA18401@mail.gnudd.com>
Alessandro Rubini wrote:
>>Robert Schwebel et al have worked socket based CAN (i.e. implement CAN
>>as _net_ dev, not as char)
>
>
> That's great. I've always been convinced it is the right way to go.
> I remember I've said so to a friend in March 2002. Unfortunately,
> I had no time to do it the right way, due to short deadlines and
> tight budget. I'm happy Robert did it.
FYI, there is also a RTDM/Xenomai based version of the SJA1000
socket-based CAN driver at
http://www.rts.uni-hannover.de/mitarbeiter/kiszka/rtaddon/
As RTDM/Xenomai is avaiable for PowerPC as well, it might be an option.
Wolfgang.
> /alessandro
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
>
>
^ permalink raw reply
* Re: Which CAN driver to port to for PPC
From: Wolfgang Grandegger @ 2005-12-29 11:53 UTC (permalink / raw)
To: David Jander; +Cc: linuxppc-embedded
In-Reply-To: <200512281302.46210.david.jander@protonic.nl>
David Jander wrote:
> Hi again,
>
> On Wednesday 28 December 2005 11:44, Wolfgang Grandegger wrote:
>
>>AFAIK, there is no _generic_ embedded CAN driver available which even
>>supports real-time extensions.
>
>
> Yes, lincan does. Well, it supports RTlinux and OCERA's RTlinux (GPL)
> modifications, which somehow reinvent ADEOS (or is it the other way around?),
> but since RTlinux is an option only for i386, and anyway almost dead right
> now, you could say it doesn't support real-time extensions.
Well, ADEOS uses a different method of handling interrupts and
exceptions to avoid the infamous RTLinux patent. Better let's say: it
doesn't support really "free" real-time extensions.
> The problem of saying "Peak-CAN for SJA1000" and "OCAN for intel" is that you
> can basically forget about writing portable code because they are both very
> different.
I agree.
> Maybe you should have a look at Pavel Pisa's lincan. After trying it out you
> might end up as confused as I am, because it doesn't look that bad at all,
> it's almost platform independent, supports all kernels (2.2 to latest 2.6),
> and supports a great amount of cards with intel and/or philips chips (yes,
> both of them on one card is also an option). The driver is designed with
> performance and throughput in mind, but I am not so sure about the API which
> is still a little too simple (maybe that's actually good) and doesn't support
> properly checking chip- or bus-status yet. Also honorable is their effort of
> staying compatible with at least one other player: can4linux.
In the meantime I had a closer look and it looks like the most advanced
in terms of portability, indeed. My experience is, that the chip- or
bus-status, apart from the bus-off state, is very hardware specific and
it's difficult to provide a generic API. Still need to dig more in
lincan to make a reasonable judgment, though.
> Greetings, and thanks for the comments,
>
> Btw, how's ELDK-4 coming along?
Please ask Wolfgang Denk directly.
Wolfgang.
^ permalink raw reply
* Re: Porting Linux2.6.13 on MPC860T custom build board
From: venkatajagadeesh p @ 2005-12-29 10:07 UTC (permalink / raw)
To: Sinan Akman, linuxppc-embedded
In-Reply-To: <43B3958E.4010002@writeme.com>
[-- Attachment #1: Type: text/plain, Size: 338 bytes --]
Hi Sinan Akman
Thanks for Your suggestion, Now linux is up and booting. thanks for the community who contributed in this porting.
Thanks and one and all,
Venkata jagadish.p
---------------------------------
Yahoo! Photos
Ring in the New Year with Photo Calendars. Add photos, events, holidays, whatever.
[-- Attachment #2: Type: text/html, Size: 602 bytes --]
^ permalink raw reply
* Re: Error: unknown pseudo-op: `.cfi_startproc'
From: HappyPhot @ 2005-12-29 9:25 UTC (permalink / raw)
To: Wolfgang Denk; +Cc: linuxppc-embedded
In-Reply-To: <20051228091612.B43D3353A66@atlas.denx.de>
> In message <007801c60b72$eb4988c0$0860120a@photon> you wrote:
>>
>> I am using ELDK (2005-06-07) and
>> linux-2.6.15-rc2-2005-12-03-2208.tar.bz2
>> to build the kernel. But there are some errors:
>>
>> .../arch/powerpc/kernel/vdso32/gettimeofday.S: Assembler messages:
>> .../arch/powerpc/kernel/vdso32/gettimeofday.S:28: Error: unknown
>> pseudo-op:
>> `.cfi_startproc'
>> .../arch/powerpc/kernel/vdso32/gettimeofday.S:30: Error: unknown
>> pseudo-op:
>> `.cfi_register'
>> .......
>>
>> Anybody knows what happened ? And is there any way to solve ?
>
> ELDK 3.1 uses binutils-2.14; the current Linux kernel was changed to
> use assembler syntax which is not supported by the GNU assembler in
> this version. See for example
> http://ozlabs.org/pipermail/linuxppc64-dev/2005-February/003179.html
>
> I don't understand why this was done, either. Especially as the
> current Linux kernel documentation ("Documentation/Changes") still
> claims that binutils 2.12 would be sufficient.
>
> You will have to update your toolchain (i. e. use ELDK 4.0) for
> working with current 2.6 kernels.
>
> Best regards,
>
> Wolfgang Denk
Hi,
Is there any "ready to burn" iso image of ELDK 4.0
available for download ? I cannot find one.
thank you,
/HappyPhot
^ permalink raw reply
* Portin Linux2.6.13 on Custom build MPC860T board
From: venkatajagadeesh p @ 2005-12-29 8:50 UTC (permalink / raw)
To: linuxppc-embedded
[-- Attachment #1.1: Type: text/plain, Size: 2433 bytes --]
We are trying to port Linux-2.6.13 on Custom build board, We gone through some of the threads and done those modifications for initializing the console. But it was not working. We are sending the output data and config file.
U-Boot 1.0.2 (Oct 13 2005 - 10:06:32)
CPU: XPC86xxxZPnnD3 at 60 MHz: 4 kB I-Cache 4 kB D-Cache FEC present
Board: FADS with db MPC860T rev ENG
DRAM: (64 MB SDRAM) unknown dramdelay (0x1) - defaulting to 70 ns64 MB
ok1
ok2
functions are over
Top of RAM usable for U-Boot at: 04000000
Reserving 141k for U-Boot at: 03fdc000
Reserving 640k for malloc() at: 03f3c000
Reserving 60 Bytes for Board Info at: 03f3bfc4
Reserving 48 Bytes for Global Data at: 03f3bf94
Stack Pointer at: 03f3bf78
New Stack Pointer is: 03f3bf78
memcopy over
Now running in RAM - U-Boot at: 03fdc000
FLASH:
in flash_get_size micron is identified ffff
device id in flash.c 18
device id correct
in flash_get_size micron is identified 1
device id in flash.c 18
device id correct
32 MB
In: serial
Out: serial
Err: serial
KGDB: [on SMC2] kgdb ready
ready
Net: FEC ETHERNET
ent into mainloop
Hit any key to stop autoboot: 0
=>loadb 0x100000 57600
## Ready for binary (kermit) download to 0x00100000 at 57600 bps...
## Total Size = 0x000e9e5d = 958045 Bytes
## Start Addr = 0x00100000
=>loadb 0x400000 57600
## Ready for binary (kermit) download to 0x00400000 at 57600 bps...
## Total Size = 0x0039c124 = 3784996 Bytes
## Start Addr = 0x00400000
=>bootm 0x100000 0x400000
## Booting image at 00100000 ...
Image Name: Linux-2.6.13
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 957981 Bytes = 935.5 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... gunzip function called
OK
do_bootm_linux called ...do_bootm_linux after ...part2 do_boot_linux before RAM
Disk image loading ...
## Loading RAMDisk Image at 00400000 ...
Image Name: Ramdisk image
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 3784932 Bytes = 3.6 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
data is non zero
Loading Ramdisk to 03b9f000, end 03f3b0e4 ... OK
## Transferring control to Linux (at address 00000000) ...
---------------------------------
Yahoo! Shopping
Find Great Deals on Holiday Gifts at Yahoo! Shopping
[-- Attachment #1.2: Type: text/html, Size: 3426 bytes --]
[-- Attachment #2: 172188218-.config --]
[-- Type: text/plain, Size: 11933 bytes --]
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.13
# Thu Dec 29 10:54:14 2005
#
CONFIG_MMU=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_HAVE_DEC_LOCK=y
CONFIG_PPC=y
CONFIG_PPC32=y
CONFIG_GENERIC_NVRAM=y
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
#
CONFIG_LOCALVERSION=""
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
# CONFIG_HOTPLUG is not set
CONFIG_KOBJECT_UEVENT=y
# CONFIG_IKCONFIG is not set
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
#
# Loadable module support
#
# CONFIG_MODULES is not set
#
# Processor
#
# CONFIG_6xx is not set
# CONFIG_40x is not set
# CONFIG_44x is not set
# CONFIG_POWER3 is not set
# CONFIG_POWER4 is not set
CONFIG_8xx=y
# CONFIG_E200 is not set
# CONFIG_E500 is not set
# CONFIG_MATH_EMULATION is not set
# CONFIG_KEXEC is not set
# CONFIG_CPU_FREQ is not set
CONFIG_WANT_EARLY_SERIAL=y
CONFIG_EMBEDDEDBOOT=y
CONFIG_NOT_COHERENT_CACHE=y
#
# Platform options
#
CONFIG_FADS=y
# CONFIG_RPXLITE is not set
# CONFIG_RPXCLASSIC is not set
# CONFIG_BSEIP is not set
CONFIG_MPC8XXFADS=y
# CONFIG_MPC86XADS is not set
# CONFIG_MPC885ADS is not set
# CONFIG_TQM823L is not set
# CONFIG_TQM850L is not set
# CONFIG_TQM855L is not set
# CONFIG_TQM860L is not set
# CONFIG_FPS850L is not set
# CONFIG_SPD823TS is not set
# CONFIG_IVMS8 is not set
# CONFIG_IVML24 is not set
# CONFIG_SM850 is not set
# CONFIG_HERMES_PRO is not set
# CONFIG_IP860 is not set
# CONFIG_LWMON is not set
# CONFIG_PCU_E is not set
# CONFIG_CCM is not set
# CONFIG_LANTEC is not set
# CONFIG_MBX is not set
# CONFIG_WINCEPT is not set
# CONFIG_HIGHMEM is not set
CONFIG_HZ_100=y
# CONFIG_HZ_250 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=100
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_MISC is not set
CONFIG_CMDLINE_BOOL=y
CONFIG_CMDLINE="console=ttyCPM1,57600 root=/dev/ram"
# CONFIG_PM is not set
CONFIG_SECCOMP=y
CONFIG_ISA_DMA_API=y
#
# Bus options
#
# CONFIG_PCI is not set
# CONFIG_PCI_DOMAINS is not set
# CONFIG_PCI_QSPAN is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
#
# Advanced setup
#
# CONFIG_ADVANCED_OPTIONS is not set
#
# Default settings for advanced configuration options are used
#
CONFIG_HIGHMEM_START=0xfe000000
CONFIG_LOWMEM_SIZE=0x30000000
CONFIG_KERNEL_START=0xc0000000
CONFIG_TASK_SIZE=0x80000000
CONFIG_CONSISTENT_START=0xff100000
CONFIG_CONSISTENT_SIZE=0x00200000
CONFIG_BOOT_LOAD=0x00400000
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
CONFIG_ARPD=y
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_IP_TCPDIAG=y
CONFIG_IP_TCPDIAG_IPV6=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_BIC=y
CONFIG_IPV6=y
# CONFIG_IPV6_PRIVACY is not set
# CONFIG_INET6_AH is not set
# CONFIG_INET6_ESP is not set
# CONFIG_INET6_IPCOMP is not set
# CONFIG_INET6_TUNNEL is not set
# CONFIG_IPV6_TUNNEL is not set
# CONFIG_NETFILTER is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
CONFIG_BRIDGE=y
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_SCHED is not set
# CONFIG_NET_CLS_ROUTE is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
# CONFIG_PARPORT is not set
#
# Plug and Play support
#
#
# Block devices
#
# CONFIG_BLK_DEV_FD is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
# CONFIG_BLK_DEV_LOOP is not set
# CONFIG_BLK_DEV_NBD is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_LBD is not set
# CONFIG_CDROM_PKTCDVD is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
# CONFIG_IOSCHED_AS is not set
# CONFIG_IOSCHED_DEADLINE is not set
# CONFIG_IOSCHED_CFQ is not set
# CONFIG_ATA_OVER_ETH is not set
#
# ATA/ATAPI/MFM/RLL support
#
# CONFIG_IDE is not set
#
# SCSI device support
#
# CONFIG_SCSI is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
#
#
# I2O device support
#
#
# Macintosh device drivers
#
#
# Network device support
#
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
#
# Ethernet (1000 Mbit)
#
#
# Ethernet (10000 Mbit)
#
#
# Token Ring devices
#
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set
#
# Input Device Drivers
#
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
#
# Hardware I/O ports
#
# CONFIG_SERIO is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_SERIAL_NONSTANDARD=y
# CONFIG_COMPUTONE is not set
# CONFIG_ROCKETPORT is not set
# CONFIG_CYCLADES is not set
# CONFIG_DIGIEPCA is not set
# CONFIG_MOXA_INTELLIO is not set
# CONFIG_MOXA_SMARTIO is not set
# CONFIG_ISI is not set
# CONFIG_SYNCLINKMP is not set
# CONFIG_N_HDLC is not set
# CONFIG_RISCOM8 is not set
# CONFIG_SPECIALIX is not set
# CONFIG_SX is not set
# CONFIG_RIO is not set
# CONFIG_STALDRV is not set
#
# Serial drivers
#
# CONFIG_SERIAL_8250 is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_CPM=y
CONFIG_SERIAL_CPM_CONSOLE=y
# CONFIG_SERIAL_CPM_SCC1 is not set
# CONFIG_SERIAL_CPM_SCC2 is not set
# CONFIG_SERIAL_CPM_SCC3 is not set
# CONFIG_SERIAL_CPM_SCC4 is not set
# CONFIG_SERIAL_CPM_SMC1 is not set
CONFIG_SERIAL_CPM_SMC2=y
CONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_NVRAM is not set
# CONFIG_GEN_RTC is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_AGP is not set
# CONFIG_RAW_DRIVER is not set
#
# TPM devices
#
#
# I2C support
#
# CONFIG_I2C is not set
# CONFIG_I2C_SENSOR is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
#
# Hardware Monitoring support
#
# CONFIG_HWMON is not set
#
# Misc devices
#
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
#
# Graphics support
#
# CONFIG_FB is not set
#
# Console display driver support
#
CONFIG_DUMMY_CONSOLE=y
#
# Sound
#
# CONFIG_SOUND is not set
#
# USB support
#
# CONFIG_USB_ARCH_HAS_HCD is not set
# CONFIG_USB_ARCH_HAS_OHCI is not set
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
#
# MMC/SD Card support
#
# CONFIG_MMC is not set
#
# InfiniBand support
#
#
# SN Devices
#
#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
CONFIG_EXT2_FS_XIP=y
CONFIG_FS_XIP=y
# CONFIG_EXT3_FS is not set
# CONFIG_JBD is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
#
# XFS support
#
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
CONFIG_ROMFS_FS=y
CONFIG_INOTIFY=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
# CONFIG_UDF_FS is not set
#
# DOS/FAT/NT Filesystems
#
# CONFIG_MSDOS_FS is not set
# CONFIG_VFAT_FS is not set
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
# CONFIG_PROC_KCORE is not set
CONFIG_SYSFS=y
# CONFIG_DEVPTS_FS_XATTR is not set
# CONFIG_TMPFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
CONFIG_NFS_FS=y
# CONFIG_NFS_V3 is not set
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
#
# Native Language Support
#
# CONFIG_NLS is not set
#
# MPC8xx CPM Options
#
# CONFIG_SCC_ENET is not set
CONFIG_FEC_ENET=y
CONFIG_USE_MDIO=y
CONFIG_FEC_AM79C874=y
# CONFIG_FEC_LXT970 is not set
# CONFIG_FEC_LXT971 is not set
# CONFIG_FEC_QS6612 is not set
CONFIG_ENET_BIG_BUFFERS=y
#
# Generic MPC8xx Options
#
# CONFIG_8xx_COPYBACK is not set
# CONFIG_8xx_CPU6 is not set
CONFIG_NO_UCODE_PATCH=y
# CONFIG_USB_SOF_UCODE_PATCH is not set
# CONFIG_I2C_SPI_UCODE_PATCH is not set
# CONFIG_I2C_SPI_SMC1_UCODE_PATCH is not set
#
# Library routines
#
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC32 is not set
# CONFIG_LIBCRC32C is not set
#
# Profiling support
#
# CONFIG_PROFILING is not set
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_LOG_BUF_SHIFT=14
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
# CONFIG_CRYPTO is not set
#
# Hardware crypto devices
#
^ permalink raw reply
* re: Porting Linux2.6.13 on MPC860T custom build board
From: venkatajagadeesh p @ 2005-12-29 5:28 UTC (permalink / raw)
To: linuxppc-embedded
[-- Attachment #1.1: Type: text/plain, Size: 2144 bytes --]
venkatajagadeesh p wrote:
>
> Hi,
> We are trying to port Linux-2.6.13 on Custom build MPC860T, board,
> We are unable to see any messages on console. We got the output given
> below. Please help us in porting the kernel.
> I am attaching the config file .
>
> =>bootm 0x100000
> ## Booting image at 00100000 ...
> Image Name: Linux-2.6.13
> Image Type: PowerPC Linux Kernel Image (gzip compressed)
> Data Size: 958189 Bytes = 935.7 kB
> Load Address: 00000000
> Entry Point: 00000000
> Verifying Checksum ... OK
> Uncompressing Kernel Image ... gunzip function called
> OK
> do_bootm_linux called ...do_bootm_linux after ...part2 do_boot_linux
> before RAM
> Disk image loading ...
> No initrd
> ## Transferring control to Linux (at address 00000000) ...
>
> >Most probably, something odd with serial setup.
> >You have enabled just all the stuff (SCC/SMC), but (on 8xx at least)
>>they can hardly live together, having alternative - conflicting IO pin configurations.
We enabling only SMC2, still it is showing the same problem. In U-boot loader we have modified the default console to SMC2. We have not done any modifications to the original linux-2.6.13 code.
I am sending config file as an attachment.
I am sending U-boot env varibles also
=>printenv
bootcmd=bootm;setenv bootargs root=/dev/ram rw
bootdelay=5
baudrate=57600
loads_echo=1
ethaddr=9a:52:63:15:85:25
bootfile=uImage
filesize=95f0a
ipaddr=192.168.3.2
serverip=192.168.3.6
netdev=eth0
netmask=255.255.255.0
addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmas
k}:${hostname}:${netdev}:off
ramargs=setenv bootargs root=/dev/ram rw
kernel_addr=0xfc0a0000
ramdisk_addr=0xfc160000
flash_ram=run ramargs addip;bootm 0xfc0a0000 0xfc160000
net_ram=tftpboot 0x100000 uImage;tftpboot 0x400000 rambb2;run ramargs addip;boot
m 0x100000 0x400000
stdin=serial
stdout=serial
stderr=serial
bootargs=root=/dev/ram rw
Environment size: 638/262140 bytes
---------------------------------
Yahoo! Photos
Ring in the New Year with Photo Calendars. Add photos, events, holidays, whatever.
[-- Attachment #1.2: Type: text/html, Size: 3026 bytes --]
[-- Attachment #2: 172188218-.config --]
[-- Type: text/plain, Size: 11955 bytes --]
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.13
# Thu Dec 29 10:54:14 2005
#
CONFIG_MMU=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_HAVE_DEC_LOCK=y
CONFIG_PPC=y
CONFIG_PPC32=y
CONFIG_GENERIC_NVRAM=y
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
#
CONFIG_LOCALVERSION=""
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
# CONFIG_HOTPLUG is not set
CONFIG_KOBJECT_UEVENT=y
# CONFIG_IKCONFIG is not set
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
#
# Loadable module support
#
# CONFIG_MODULES is not set
#
# Processor
#
# CONFIG_6xx is not set
# CONFIG_40x is not set
# CONFIG_44x is not set
# CONFIG_POWER3 is not set
# CONFIG_POWER4 is not set
CONFIG_8xx=y
# CONFIG_E200 is not set
# CONFIG_E500 is not set
# CONFIG_MATH_EMULATION is not set
# CONFIG_KEXEC is not set
# CONFIG_CPU_FREQ is not set
# CONFIG_WANT_EARLY_SERIAL is not set
CONFIG_EMBEDDEDBOOT=y
CONFIG_NOT_COHERENT_CACHE=y
#
# Platform options
#
CONFIG_FADS=y
# CONFIG_RPXLITE is not set
# CONFIG_RPXCLASSIC is not set
# CONFIG_BSEIP is not set
CONFIG_MPC8XXFADS=y
# CONFIG_MPC86XADS is not set
# CONFIG_MPC885ADS is not set
# CONFIG_TQM823L is not set
# CONFIG_TQM850L is not set
# CONFIG_TQM855L is not set
# CONFIG_TQM860L is not set
# CONFIG_FPS850L is not set
# CONFIG_SPD823TS is not set
# CONFIG_IVMS8 is not set
# CONFIG_IVML24 is not set
# CONFIG_SM850 is not set
# CONFIG_HERMES_PRO is not set
# CONFIG_IP860 is not set
# CONFIG_LWMON is not set
# CONFIG_PCU_E is not set
# CONFIG_CCM is not set
# CONFIG_LANTEC is not set
# CONFIG_MBX is not set
# CONFIG_WINCEPT is not set
# CONFIG_HIGHMEM is not set
CONFIG_HZ_100=y
# CONFIG_HZ_250 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=100
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_MISC is not set
CONFIG_CMDLINE_BOOL=y
CONFIG_CMDLINE="console=ttyS1,57600 console=tty1 root=/dev/ram"
# CONFIG_PM is not set
CONFIG_SECCOMP=y
CONFIG_ISA_DMA_API=y
#
# Bus options
#
# CONFIG_PCI is not set
# CONFIG_PCI_DOMAINS is not set
# CONFIG_PCI_QSPAN is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
#
# Advanced setup
#
# CONFIG_ADVANCED_OPTIONS is not set
#
# Default settings for advanced configuration options are used
#
CONFIG_HIGHMEM_START=0xfe000000
CONFIG_LOWMEM_SIZE=0x30000000
CONFIG_KERNEL_START=0xc0000000
CONFIG_TASK_SIZE=0x80000000
CONFIG_CONSISTENT_START=0xff100000
CONFIG_CONSISTENT_SIZE=0x00200000
CONFIG_BOOT_LOAD=0x00400000
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
CONFIG_ARPD=y
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_IP_TCPDIAG=y
CONFIG_IP_TCPDIAG_IPV6=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_BIC=y
CONFIG_IPV6=y
# CONFIG_IPV6_PRIVACY is not set
# CONFIG_INET6_AH is not set
# CONFIG_INET6_ESP is not set
# CONFIG_INET6_IPCOMP is not set
# CONFIG_INET6_TUNNEL is not set
# CONFIG_IPV6_TUNNEL is not set
# CONFIG_NETFILTER is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
CONFIG_BRIDGE=y
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_SCHED is not set
# CONFIG_NET_CLS_ROUTE is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
# CONFIG_PARPORT is not set
#
# Plug and Play support
#
#
# Block devices
#
# CONFIG_BLK_DEV_FD is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
# CONFIG_BLK_DEV_LOOP is not set
# CONFIG_BLK_DEV_NBD is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_LBD is not set
# CONFIG_CDROM_PKTCDVD is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
# CONFIG_IOSCHED_AS is not set
# CONFIG_IOSCHED_DEADLINE is not set
# CONFIG_IOSCHED_CFQ is not set
# CONFIG_ATA_OVER_ETH is not set
#
# ATA/ATAPI/MFM/RLL support
#
# CONFIG_IDE is not set
#
# SCSI device support
#
# CONFIG_SCSI is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
#
#
# I2O device support
#
#
# Macintosh device drivers
#
#
# Network device support
#
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
#
# Ethernet (1000 Mbit)
#
#
# Ethernet (10000 Mbit)
#
#
# Token Ring devices
#
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set
#
# Input Device Drivers
#
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
#
# Hardware I/O ports
#
# CONFIG_SERIO is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_SERIAL_NONSTANDARD=y
# CONFIG_COMPUTONE is not set
# CONFIG_ROCKETPORT is not set
# CONFIG_CYCLADES is not set
# CONFIG_DIGIEPCA is not set
# CONFIG_MOXA_INTELLIO is not set
# CONFIG_MOXA_SMARTIO is not set
# CONFIG_ISI is not set
# CONFIG_SYNCLINKMP is not set
# CONFIG_N_HDLC is not set
# CONFIG_RISCOM8 is not set
# CONFIG_SPECIALIX is not set
# CONFIG_SX is not set
# CONFIG_RIO is not set
# CONFIG_STALDRV is not set
#
# Serial drivers
#
# CONFIG_SERIAL_8250 is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_CPM=y
CONFIG_SERIAL_CPM_CONSOLE=y
# CONFIG_SERIAL_CPM_SCC1 is not set
# CONFIG_SERIAL_CPM_SCC2 is not set
# CONFIG_SERIAL_CPM_SCC3 is not set
# CONFIG_SERIAL_CPM_SCC4 is not set
# CONFIG_SERIAL_CPM_SMC1 is not set
CONFIG_SERIAL_CPM_SMC2=y
CONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_NVRAM is not set
# CONFIG_GEN_RTC is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_AGP is not set
# CONFIG_RAW_DRIVER is not set
#
# TPM devices
#
#
# I2C support
#
# CONFIG_I2C is not set
# CONFIG_I2C_SENSOR is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
#
# Hardware Monitoring support
#
# CONFIG_HWMON is not set
#
# Misc devices
#
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
#
# Graphics support
#
# CONFIG_FB is not set
#
# Console display driver support
#
CONFIG_DUMMY_CONSOLE=y
#
# Sound
#
# CONFIG_SOUND is not set
#
# USB support
#
# CONFIG_USB_ARCH_HAS_HCD is not set
# CONFIG_USB_ARCH_HAS_OHCI is not set
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
#
# MMC/SD Card support
#
# CONFIG_MMC is not set
#
# InfiniBand support
#
#
# SN Devices
#
#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
CONFIG_EXT2_FS_XIP=y
CONFIG_FS_XIP=y
# CONFIG_EXT3_FS is not set
# CONFIG_JBD is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
#
# XFS support
#
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
CONFIG_ROMFS_FS=y
CONFIG_INOTIFY=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
# CONFIG_UDF_FS is not set
#
# DOS/FAT/NT Filesystems
#
# CONFIG_MSDOS_FS is not set
# CONFIG_VFAT_FS is not set
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
# CONFIG_PROC_KCORE is not set
CONFIG_SYSFS=y
# CONFIG_DEVPTS_FS_XATTR is not set
# CONFIG_TMPFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
CONFIG_NFS_FS=y
# CONFIG_NFS_V3 is not set
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
#
# Native Language Support
#
# CONFIG_NLS is not set
#
# MPC8xx CPM Options
#
# CONFIG_SCC_ENET is not set
CONFIG_FEC_ENET=y
CONFIG_USE_MDIO=y
CONFIG_FEC_AM79C874=y
# CONFIG_FEC_LXT970 is not set
# CONFIG_FEC_LXT971 is not set
# CONFIG_FEC_QS6612 is not set
CONFIG_ENET_BIG_BUFFERS=y
#
# Generic MPC8xx Options
#
# CONFIG_8xx_COPYBACK is not set
# CONFIG_8xx_CPU6 is not set
CONFIG_NO_UCODE_PATCH=y
# CONFIG_USB_SOF_UCODE_PATCH is not set
# CONFIG_I2C_SPI_UCODE_PATCH is not set
# CONFIG_I2C_SPI_SMC1_UCODE_PATCH is not set
#
# Library routines
#
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC32 is not set
# CONFIG_LIBCRC32C is not set
#
# Profiling support
#
# CONFIG_PROFILING is not set
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_LOG_BUF_SHIFT=14
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
# CONFIG_CRYPTO is not set
#
# Hardware crypto devices
#
^ permalink raw reply
* MPC8347 USB problem : Copying big file[>150MB] discontinuous via Samba
From: Sam Song @ 2005-12-29 4:37 UTC (permalink / raw)
To: linuxppc-embedded list
Hi all,
We met a USB performance problem on a custom 8347
board with 2.4.31. When copying small files no
more than 100MB in size, it worked smoothly with
NEC or VIA PCI card. But copying a big file like
more than 150MB in size would decrease the
copying
speed a lot. Serial console even couldn't
response
'ls' command. The target has a 128MB DDR RAM.
While the same driver with 2.4.31 worked fine on
a
8248 custom board. What could the problem be?
Sorry to distrub you during Christmas Time.
Thanks in advance,
Sam
Best regards,
Sam
__________________________________________________
赶快注册雅虎超大容量免费邮箱?
http://cn.mail.yahoo.com
^ permalink raw reply
* Re: AW: AW: Kernel cmdline
From: Arnd Bergmann @ 2005-12-28 22:58 UTC (permalink / raw)
To: linuxppc-embedded, achim.machura
In-Reply-To: <002501c60710$efc71270$34f1ff0a@beint.local>
On Thursday 22 December 2005 16:01, Achim Machura wrote:
> i want check an argument given by the bootloader via commandline
>
You should use module_param() for this, that will take care
of both kernel and module parameters, for more information,
see http://lwn.net/Articles/22197/.
Arnd <><
^ permalink raw reply
* Re: mv643xx_eth, sleeping function called from invalid context at mm/slab.c:2472
From: Dale Farnsworth @ 2005-12-28 22:49 UTC (permalink / raw)
To: linuxppc-dev; +Cc: olh
(For unknown reasons, I didn't receive this message directly from the
mailing list, and the archive doesn't seem to have message-ids, so
I can't supply a References: header.)
Olaf Hering reported:
> I get this with 2.6.15-rc6 on a pegasos2 board:
>
> MV-643xx 10/100/1000 Ethernet Driver
> eth1: port 1 with MAC address 00:2b:2f:de:ad:01
> eth1: Scatter Gather Enabled
> eth1: TX TCP/IP Checksumming Supported
> eth1: RX TCP/UDP Checksum Offload ON
> eth1: RX NAPI Enabled
> eth1: Using SRAM
> Debug: sleeping function called from invalid context at mm/slab.c:2472
> in_atomic():0, irqs_disabled():1
> Call Trace:
> [CB32DCF0] [C000AFCC] show_stack+0x54/0x180 (unreliable)
> [CB32DD10] [C0027CD4] __might_sleep+0xbc/0xd0
> [CB32DD20] [C005E50C] kmem_cache_alloc+0x34/0x108
> [CB32DD40] [C01C5F40] rand_initialize_irq+0x40/0x6c
> [CB32DD60] [C0054104] setup_irq+0x5c/0x154
> [CB32DD90] [C0054284] request_irq+0x88/0xb8
> [CB32DDC0] [D22820A0] mv643xx_eth_open+0x44/0xb4 [mv643xx_eth]
> [CB32DDE0] [C0257394] dev_open+0x70/0xd8
> [CB32DE00] [C02554F0] dev_change_flags+0x6c/0x13c
> [CB32DE20] [C02A2818] devinet_ioctl+0x280/0x708
> [CB32DE80] [C02A319C] inet_ioctl+0xb4/0x100
> [CB32DE90] [C02C0078] packet_ioctl+0x15c/0x188
> [CB32DEB0] [C024B998] sock_ioctl+0x30c/0x334
> [CB32DED0] [C00922F4] do_ioctl+0x3c/0x88
> [CB32DEE0] [C0092728] vfs_ioctl+0x3e8/0x424
> [CB32DF10] [C00927CC] sys_ioctl+0x68/0x98
> [CB32DF40] [C000FAEC] ret_from_syscall+0x0/0x4c
> --- Exception: c01 at 0x7f6be80
> LR = 0x7fec9d0
> eth1: no IPv6 routers present
I just posted the following patch to the netdev list which should address
this problem.
-Dale
Date: Wed, 28 Dec 2005 15:40:01 -0700
To: netdev@vger.kernel.org
Subject: [PATCH 4/4] mv643xx: Don't call request_irq with a held lock
Message-ID: <20051228224001.GD5742@xyzzy.farnsworth.org>
References: <20051228223449.GA5742@xyzzy.farnsworth.org>
From: Dale Farnsworth <dale@farnsworth.org>
We can't call request_irq() while holding a spin lock.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Index: linux-2.6-mv643xx_enet/drivers/net/mv643xx_eth.c
===================================================================
--- linux-2.6-mv643xx_enet.orig/drivers/net/mv643xx_eth.c
+++ linux-2.6-mv643xx_enet/drivers/net/mv643xx_eth.c
@@ -655,34 +655,24 @@ static int mv643xx_eth_open(struct net_d
unsigned int port_num = mp->port_num;
int err;
- spin_lock_irq(&mp->lock);
-
err = request_irq(dev->irq, mv643xx_eth_int_handler,
SA_SHIRQ | SA_SAMPLE_RANDOM, dev->name, dev);
-
if (err) {
printk(KERN_ERR "Can not assign IRQ number to MV643XX_eth%d\n",
port_num);
- err = -EAGAIN;
- goto out;
+ return -EAGAIN;
}
+ spin_lock_irq(&mp->lock);
+
if (mv643xx_eth_real_open(dev)) {
printk("%s: Error opening interface\n", dev->name);
+ free_irq(dev->irq, dev);
err = -EBUSY;
- goto out_free;
}
spin_unlock_irq(&mp->lock);
- return 0;
-
-out_free:
- free_irq(dev->irq, dev);
-
-out:
- spin_unlock_irq(&mp->lock);
-
return err;
}
^ permalink raw reply
* [PATCH 2/2] ppc32: MPC885ADS, MPC866ADS and MPC8272ADS-specific platform stuff for fs_enet(resend)
From: Vitaly Bordug @ 2005-12-28 20:09 UTC (permalink / raw)
To: Kumar Gala; +Cc: linuxppc-embedded list
In-Reply-To: <20051228191803.30378.93344.stgit@vitb.dev.rtsoft.ru>
Added proper ppc_sys identification and fs_platform_info's for MPC 885ADS,
866ADS and 8272ADS, utilising function assignment to remove/do not use
platform devices which conflict with PD-incompatible drivers.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
---
arch/ppc/Kconfig | 47 ++++
arch/ppc/platforms/Makefile | 4
arch/ppc/platforms/fads.h | 2
arch/ppc/platforms/mpc8272ads_setup.c | 236 ++++++++++++++++++++
arch/ppc/platforms/mpc866ads_setup.c | 270 +++++++++++++++++++++++
arch/ppc/platforms/mpc885ads_setup.c | 387 +++++++++++++++++++++++++++++++++
arch/ppc/platforms/pq2ads.h | 4
arch/ppc/platforms/pq2ads_pd.h | 114 ++++++++++
arch/ppc/syslib/ppc_sys.c | 4
drivers/base/platform.c | 2
10 files changed, 1066 insertions(+), 4 deletions(-)
diff --git a/arch/ppc/Kconfig b/arch/ppc/Kconfig
index cc3f64c..ac32793 100644
--- a/arch/ppc/Kconfig
+++ b/arch/ppc/Kconfig
@@ -506,6 +506,53 @@ config WINCEPT
endchoice
+menu "Freescale Ethernet driver platform-specific options"
+ depends on FS_ENET
+
+ config MPC8xx_SECOND_ETH
+ bool "Second Ethernet channel"
+ depends on (MPC885ADS || MPC86XADS)
+ default y
+ help
+ This enables support for second Ethernet on MPC885ADS and MPC86xADS boards.
+ The latter will use SCC1, for 885ADS you can select it below.
+
+ choice
+ prompt "Second Ethernet channel"
+ depends on MPC8xx_SECOND_ETH
+ default MPC8xx_SECOND_ETH_FEC2
+
+ config MPC8xx_SECOND_ETH_FEC2
+ bool "FEC2"
+ depends on MPC885ADS
+ help
+ Enable FEC2 to serve as 2-nd Ethernet channel. Note that SMC2
+ (often 2-nd UART) will not work if this is enabled.
+
+ config MPC8xx_SECOND_ETH_SCC1
+ bool "SCC1"
+ depends on MPC86XADS
+ select MPC8xx_SCC_ENET_FIXED
+ help
+ Enable SCC1 to serve as 2-nd Ethernet channel. Note that SMC1
+ (often 1-nd UART) will not work if this is enabled.
+
+ config MPC8xx_SECOND_ETH_SCC3
+ bool "SCC3"
+ depends on MPC885ADS
+ help
+ Enable SCC3 to serve as 2-nd Ethernet channel. Note that SMC1
+ (often 1-nd UART) will not work if this is enabled.
+
+ endchoice
+
+ config MPC8xx_SCC_ENET_FIXED
+ depends on MPC8xx_SECOND_ETH_SCC
+ default n
+ bool "Use fixed MII-less mode for SCC Ethernet"
+
+endmenu
+
choice
prompt "Machine Type"
depends on 6xx || POWER3 || POWER4
diff --git a/arch/ppc/platforms/Makefile b/arch/ppc/platforms/Makefile
index 7c5cdab..ee50b0d 100644
--- a/arch/ppc/platforms/Makefile
+++ b/arch/ppc/platforms/Makefile
@@ -22,6 +22,8 @@ ifeq ($(CONFIG_PPC_PMAC),y)
obj-$(CONFIG_NVRAM) += pmac_nvram.o
obj-$(CONFIG_CPU_FREQ_PMAC) += pmac_cpufreq.o
endif
+
+obj-$(CONFIG_ADS8272) += mpc8272ads_setup.o
obj-$(CONFIG_PMAC_BACKLIGHT) += pmac_backlight.o
obj-$(CONFIG_PREP_RESIDUAL) += residual.o
obj-$(CONFIG_PQ2ADS) += pq2ads.o
@@ -45,6 +47,8 @@ obj-$(CONFIG_SBC82xx) += sbc82xx.o
obj-$(CONFIG_SPRUCE) += spruce.o
obj-$(CONFIG_LITE5200) += lite5200.o
obj-$(CONFIG_EV64360) += ev64360.o
+obj-$(CONFIG_MPC86XADS) += mpc866ads_setup.o
+obj-$(CONFIG_MPC885ADS) += mpc885ads_setup.o
ifeq ($(CONFIG_SMP),y)
obj-$(CONFIG_PPC_PMAC) += pmac_smp.o
diff --git a/arch/ppc/platforms/fads.h b/arch/ppc/platforms/fads.h
index a48fb8d..e1c0b1b 100644
--- a/arch/ppc/platforms/fads.h
+++ b/arch/ppc/platforms/fads.h
@@ -112,7 +112,7 @@
/* CPM Ethernet through SCC1 or SCC2 */
-#ifdef CONFIG_SCC1_ENET /* Probably 860 variant */
+#if defined(CONFIG_SCC1_ENET) || defined(CONFIG_MPC8xx_SECOND_ETH_SCC1) /* Probably 860 variant */
/* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC1 use.
* TCLK - CLK1, RCLK - CLK2.
diff --git a/arch/ppc/platforms/mpc8272ads_setup.c b/arch/ppc/platforms/mpc8272ads_setup.c
new file mode 100644
index 0000000..e45b91a
--- /dev/null
+++ b/arch/ppc/platforms/mpc8272ads_setup.c
@@ -0,0 +1,236 @@
+/*
+ * arch/ppc/platforms/82xx/pq2ads_pd.c
+ *
+ * MPC82xx Board-specific PlatformDevice descriptions
+ *
+ * 2005 (c) MontaVista Software, Inc.
+ * Vitaly Bordug <vbordug@ru.mvista.com>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/ioport.h>
+#include <linux/fs_enet_pd.h>
+#include <linux/platform_device.h>
+
+#include <asm/io.h>
+#include <asm/mpc8260.h>
+#include <asm/cpm2.h>
+#include <asm/immap_cpm2.h>
+#include <asm/irq.h>
+#include <asm/ppc_sys.h>
+#include <asm/ppcboot.h>
+
+#include "pq2ads_pd.h"
+
+static void init_fcc1_ioports(void);
+static void init_fcc2_ioports(void);
+
+static struct fs_mii_bus_info mii_bus_info = {
+ .method = fsmii_bitbang,
+ .id = 0,
+ .i.bitbang = {
+ .mdio_port = fsiop_portc,
+ .mdio_bit = 18,
+ .mdc_port = fsiop_portc,
+ .mdc_bit = 19,
+ .delay = 1,
+ },
+};
+
+static struct fs_platform_info mpc82xx_fcc1_pdata = {
+ .fs_no = fsid_fcc1,
+ .cp_page = CPM_CR_FCC1_PAGE,
+ .cp_block = CPM_CR_FCC1_SBLOCK,
+ .clk_trx = (PC_F1RXCLK | PC_F1TXCLK),
+ .clk_route = CMX1_CLK_ROUTE,
+ .clk_mask = CMX1_CLK_MASK,
+ .init_ioports = init_fcc1_ioports,
+
+ .phy_addr = 0,
+#ifdef PHY_INTERRUPT
+ .phy_irq = PHY_INTERRUPT,
+#else
+ .phy_irq = -1;
+#endif
+ .mem_offset = FCC1_MEM_OFFSET,
+ .bus_info = &mii_bus_info,
+ .rx_ring = 32,
+ .tx_ring = 32,
+ .rx_copybreak = 240,
+ .use_napi = 0,
+ .napi_weight = 17,
+};
+
+static struct fs_platform_info mpc82xx_fcc2_pdata = {
+ .fs_no = fsid_fcc2,
+ .cp_page = CPM_CR_FCC2_PAGE,
+ .cp_block = CPM_CR_FCC2_SBLOCK,
+ .clk_trx = (PC_F2RXCLK | PC_F2TXCLK),
+ .clk_route = CMX2_CLK_ROUTE,
+ .clk_mask = CMX2_CLK_MASK,
+ .init_ioports = init_fcc2_ioports,
+
+ .phy_addr = 3,
+#ifdef PHY_INTERRUPT
+ .phy_irq = PHY_INTERRUPT,
+#else
+ .phy_irq = -1;
+#endif
+ .mem_offset = FCC2_MEM_OFFSET,
+ .bus_info = &mii_bus_info,
+ .rx_ring = 32,
+ .tx_ring = 32,
+ .rx_copybreak = 240,
+ .use_napi = 0,
+ .napi_weight = 17,
+};
+
+static void init_fcc1_ioports(void)
+{
+ struct io_port *io;
+ u32 tempval;
+ cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t));
+ u32 *bcsr = ioremap(BCSR_ADDR+4, sizeof(u32));
+
+ io = &immap->im_ioport;
+
+ /* Enable the PHY */
+ clrbits32(bcsr, BCSR1_FETHIEN);
+ setbits32(bcsr, BCSR1_FETH_RST);
+
+ /* FCC1 pins are on port A/C. */
+ /* Configure port A and C pins for FCC1 Ethernet. */
+
+ tempval = in_be32(&io->iop_pdira);
+ tempval &= ~PA1_DIRA0;
+ tempval |= PA1_DIRA1;
+ out_be32(&io->iop_pdira, tempval);
+
+ tempval = in_be32(&io->iop_psora);
+ tempval &= ~PA1_PSORA0;
+ tempval |= PA1_PSORA1;
+ out_be32(&io->iop_psora, tempval);
+
+ setbits32(&io->iop_ppara,PA1_DIRA0 | PA1_DIRA1);
+
+ /* Alter clocks */
+ tempval = PC_F1TXCLK|PC_F1RXCLK;
+
+ clrbits32(&io->iop_psorc, tempval);
+ clrbits32(&io->iop_pdirc, tempval);
+ setbits32(&io->iop_pparc, tempval);
+
+ clrbits32(&immap->im_cpmux.cmx_fcr, CMX1_CLK_MASK);
+ setbits32(&immap->im_cpmux.cmx_fcr, CMX1_CLK_ROUTE);
+ iounmap(bcsr);
+ iounmap(immap);
+}
+
+static void init_fcc2_ioports(void)
+{
+ cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t));
+ u32 *bcsr = ioremap(BCSR_ADDR+12, sizeof(u32));
+
+ struct io_port *io;
+ u32 tempval;
+
+ immap = cpm2_immr;
+
+ io = &immap->im_ioport;
+
+ /* Enable the PHY */
+ clrbits32(bcsr, BCSR3_FETHIEN2);
+ setbits32(bcsr, BCSR3_FETH2_RST);
+
+ /* FCC2 are port B/C. */
+ /* Configure port A and C pins for FCC2 Ethernet. */
+
+ tempval = in_be32(&io->iop_pdirb);
+ tempval &= ~PB2_DIRB0;
+ tempval |= PB2_DIRB1;
+ out_be32(&io->iop_pdirb, tempval);
+
+ tempval = in_be32(&io->iop_psorb);
+ tempval &= ~PB2_PSORB0;
+ tempval |= PB2_PSORB1;
+ out_be32(&io->iop_psorb, tempval);
+
+ setbits32(&io->iop_pparb,PB2_DIRB0 | PB2_DIRB1);
+
+ tempval = PC_F2RXCLK|PC_F2TXCLK;
+
+ /* Alter clocks */
+ clrbits32(&io->iop_psorc,tempval);
+ clrbits32(&io->iop_pdirc,tempval);
+ setbits32(&io->iop_pparc,tempval);
+
+ clrbits32(&immap->im_cpmux.cmx_fcr, CMX2_CLK_MASK);
+ setbits32(&immap->im_cpmux.cmx_fcr, CMX2_CLK_ROUTE);
+
+ iounmap(bcsr);
+ iounmap(immap);
+}
+
+
+static void __init mpc8272ads_fixup_enet_pdata(struct platform_device *pdev,
+ int idx)
+{
+ bd_t* bi = (void*)__res;
+ int fs_no = fsid_fcc1+pdev->id-1;
+
+ mpc82xx_fcc1_pdata.dpram_offset = mpc82xx_fcc2_pdata.dpram_offset = (u32)cpm2_immr->im_dprambase;
+ mpc82xx_fcc1_pdata.fcc_regs_c = mpc82xx_fcc2_pdata.fcc_regs_c = (u32)cpm2_immr->im_fcc_c;
+
+ switch(fs_no) {
+ case fsid_fcc1:
+ memcpy(&mpc82xx_fcc1_pdata.macaddr,bi->bi_enetaddr,6);
+ pdev->dev.platform_data = &mpc82xx_fcc1_pdata;
+ break;
+ case fsid_fcc2:
+ memcpy(&mpc82xx_fcc2_pdata.macaddr,bi->bi_enetaddr,6);
+ mpc82xx_fcc2_pdata.macaddr[5] ^= 1;
+ pdev->dev.platform_data = &mpc82xx_fcc2_pdata;
+ break;
+ }
+ printk("all\n");
+}
+
+static int mpc8272ads_platform_notify(struct device *dev)
+{
+ static const struct platform_notify_dev_map dev_map[] = {
+ {
+ .bus_id = "fsl-cpm-fcc",
+ .rtn = mpc8272ads_fixup_enet_pdata
+ },
+ {
+ .bus_id = NULL
+ }
+ };
+ platform_notify_map(dev_map,dev);
+
+ return 0;
+
+}
+
+int __init mpc8272ads_init(void)
+{
+ printk(KERN_NOTICE "mpc8272ads: Init\n");
+
+ platform_notify = mpc8272ads_platform_notify;
+
+ ppc_sys_device_initfunc();
+
+ ppc_sys_device_enable(MPC82xx_CPM_FCC1);
+ ppc_sys_device_enable(MPC82xx_CPM_FCC2);
+
+ return 0;
+}
+
+arch_initcall(mpc8272ads_init);
diff --git a/arch/ppc/platforms/mpc866ads_setup.c b/arch/ppc/platforms/mpc866ads_setup.c
new file mode 100644
index 0000000..26b989f
--- /dev/null
+++ b/arch/ppc/platforms/mpc866ads_setup.c
@@ -0,0 +1,270 @@
+/*arch/ppc/platforms/mpc885ads-setup.c
+ *
+ * Platform setup for the Freescale mpc885ads board
+ *
+ * Vitaly Bordug <vbordug@ru.mvista.com>
+ *
+ * Copyright 2005 MontaVista Software Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/param.h>
+#include <linux/string.h>
+#include <linux/ioport.h>
+#include <linux/device.h>
+
+#include <linux/fs_enet_pd.h>
+#include <linux/mii.h>
+
+#include <asm/delay.h>
+#include <asm/io.h>
+#include <asm/machdep.h>
+#include <asm/page.h>
+#include <asm/processor.h>
+#include <asm/system.h>
+#include <asm/time.h>
+#include <asm/ppcboot.h>
+#include <asm/8xx_immap.h>
+#include <asm/commproc.h>
+#include <asm/ppc_sys.h>
+#include <asm/mpc8xx.h>
+
+extern unsigned char __res[];
+
+static struct fs_mii_bus_info fec_mii_bus_info = {
+ .method = fsmii_fec,
+ .id = 0,
+};
+
+static struct fs_mii_bus_info scc_mii_bus_info = {
+ .method = fsmii_fixed,
+ .id = 0,
+ .i.fixed.speed = 10,
+ .i.fixed.duplex = 0,
+};
+
+static struct fs_platform_info mpc8xx_fec_pdata[] = {
+ {
+ .rx_ring = 128,
+ .tx_ring = 16,
+ .rx_copybreak = 240,
+
+ .use_napi = 1,
+ .napi_weight = 17,
+
+ .phy_addr = 15,
+ .phy_irq = -1,
+
+ .use_rmii = 0,
+
+ .bus_info = &fec_mii_bus_info,
+ }
+};
+
+static struct fs_platform_info mpc8xx_scc_pdata = {
+ .rx_ring = 64,
+ .tx_ring = 8,
+ .rx_copybreak = 240,
+
+ .use_napi = 1,
+ .napi_weight = 17,
+
+ .phy_addr = -1,
+ .phy_irq = -1,
+
+ .bus_info = &scc_mii_bus_info,
+};
+
+void __init board_init(void)
+{
+ volatile cpm8xx_t *cp = cpmp;
+ unsigned *bcsr_io;
+
+ bcsr_io = ioremap(BCSR1, sizeof(unsigned long));
+
+ if (bcsr_io == NULL) {
+ printk(KERN_CRIT "Could not remap BCSR1\n");
+ return;
+ }
+#ifdef CONFIG_SERIAL_CPM_SMC1
+ cp->cp_simode &= ~(0xe0000000 >> 17); /* brg1 */
+ clrbits32(bcsr_io,(0x80000000 >> 7));
+#else
+ setbits32(bcsr_io,(0x80000000 >> 7));
+
+ cp->cp_pbpar &= ~(0x000000c0);
+ cp->cp_pbdir |= 0x000000c0;
+ cp->cp_smc[0].smc_smcmr = 0;
+ cp->cp_smc[0].smc_smce = 0;
+#endif
+
+#ifdef CONFIG_SERIAL_CPM_SMC2
+ cp->cp_simode &= ~(0xe0000000 >> 1);
+ cp->cp_simode |= (0x20000000 >> 1); /* brg2 */
+ clrbits32(bcsr_io,(0x80000000 >> 13));
+#else
+ clrbits32(bcsr_io,(0x80000000 >> 13));
+ cp->cp_pbpar &= ~(0x00000c00);
+ cp->cp_pbdir |= 0x00000c00;
+ cp->cp_smc[1].smc_smcmr = 0;
+ cp->cp_smc[1].smc_smce = 0;
+#endif
+ iounmap(bcsr_io);
+}
+
+static void setup_fec1_ioports(void)
+{
+ immap_t *immap = (immap_t *) IMAP_ADDR;
+
+ setbits16(&immap->im_ioport.iop_pdpar, 0x1fff);
+ setbits16(&immap->im_ioport.iop_pddir, 0x1fff);
+}
+
+static void setup_scc1_ioports(void)
+{
+ immap_t *immap = (immap_t *) IMAP_ADDR;
+ unsigned *bcsr_io;
+
+ bcsr_io = ioremap(BCSR1, sizeof(unsigned long));
+
+ if (bcsr_io == NULL) {
+ printk(KERN_CRIT "Could not remap BCSR1\n");
+ return;
+ }
+
+ /* Enable the PHY.
+ */
+ clrbits32(bcsr_io,BCSR1_ETHEN);
+
+ /* Configure port A pins for Txd and Rxd.
+ */
+ /* Disable receive and transmit in case EPPC-Bug started it.
+ */
+ setbits16(&immap->im_ioport.iop_papar, PA_ENET_RXD | PA_ENET_TXD);
+ clrbits16(&immap->im_ioport.iop_padir, PA_ENET_RXD | PA_ENET_TXD);
+ clrbits16(&immap->im_ioport.iop_paodr, PA_ENET_TXD);
+
+ /* Configure port C pins to enable CLSN and RENA.
+ */
+ clrbits16(&immap->im_ioport.iop_pcpar, PC_ENET_CLSN | PC_ENET_RENA);
+ clrbits16(&immap->im_ioport.iop_pcdir, PC_ENET_CLSN | PC_ENET_RENA);
+ setbits16(&immap->im_ioport.iop_pcso, PC_ENET_CLSN | PC_ENET_RENA);
+ /* Configure port A for TCLK and RCLK.
+ */
+ setbits16(&immap->im_ioport.iop_papar, PA_ENET_TCLK | PA_ENET_RCLK);
+ clrbits16(&immap->im_ioport.iop_padir, PA_ENET_TCLK | PA_ENET_RCLK);
+ clrbits32(&immap->im_cpm.cp_pbpar, PB_ENET_TENA);
+ clrbits32(&immap->im_cpm.cp_pbdir, PB_ENET_TENA);
+
+ /* Configure Serial Interface clock routing.
+ * First, clear all SCC bits to zero, then set the ones we want.
+ */
+ clrbits32(&immap->im_cpm.cp_sicr, SICR_ENET_MASK);
+ setbits32(&immap->im_cpm.cp_sicr, SICR_ENET_CLKRT);
+
+ /* In the original SCC enet driver the following code is placed at
+ the end of the initialization */
+ setbits32(&immap->im_cpm.cp_pbpar, PB_ENET_TENA);
+ setbits32(&immap->im_cpm.cp_pbdir, PB_ENET_TENA);
+
+}
+
+static void mpc866ads_fixup_enet_pdata(struct platform_device *pdev, int fs_no)
+{
+ struct fs_platform_info *fpi = pdev->dev.platform_data;
+
+ volatile cpm8xx_t *cp;
+ bd_t *bd = (bd_t *) __res;
+ char *e;
+ int i;
+
+ /* Get pointer to Communication Processor */
+ cp = cpmp;
+ switch (fs_no) {
+ case fsid_fec1:
+ fpi = &mpc8xx_fec_pdata[0];
+ fpi->init_ioports = &setup_fec1_ioports;
+
+ break;
+ case fsid_scc1:
+ fpi = &mpc8xx_scc_pdata;
+ fpi->init_ioports = &setup_scc1_ioports;
+
+ break;
+ default:
+ break;
+ }
+
+ pdev->dev.platform_data = fpi;
+ fpi->fs_no = fs_no;
+
+ e = (unsigned char *)&bd->bi_enetaddr;
+ for (i = 0; i < 6; i++)
+ fpi->macaddr[i] = *e++;
+
+ fpi->macaddr[5 - pdev->id]++;
+
+}
+
+static void mpc866ads_fixup_fec_enet_pdata(struct platform_device *pdev,
+ int idx)
+{
+ /* This is for FEC devices only */
+ if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-fec")))
+ return;
+ mpc866ads_fixup_enet_pdata(pdev, fsid_fec1 + pdev->id - 1);
+}
+
+static void mpc866ads_fixup_scc_enet_pdata(struct platform_device *pdev,
+ int idx)
+{
+ /* This is for SCC devices only */
+ if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-scc")))
+ return;
+
+ mpc866ads_fixup_enet_pdata(pdev, fsid_scc1 + pdev->id - 1);
+}
+
+static int mpc866ads_platform_notify(struct device *dev)
+{
+ static const struct platform_notify_dev_map dev_map[] = {
+ {
+ .bus_id = "fsl-cpm-fec",
+ .rtn = mpc866ads_fixup_fec_enet_pdata,
+ },
+ {
+ .bus_id = "fsl-cpm-scc",
+ .rtn = mpc866ads_fixup_scc_enet_pdata,
+ },
+ {
+ .bus_id = NULL
+ }
+ };
+
+ platform_notify_map(dev_map,dev);
+
+ return 0;
+}
+
+int __init mpc866ads_init(void)
+{
+ printk(KERN_NOTICE "mpc866ads: Init\n");
+
+ platform_notify = mpc866ads_platform_notify;
+
+ ppc_sys_device_initfunc();
+#ifdef MPC8xx_SECOND_ETH_SCC1
+ ppc_sys_device_enable(MPC8xx_CPM_SCC1);
+#endif
+ ppc_sys_device_enable(MPC8xx_CPM_FEC1);
+
+ return 0;
+}
+
+arch_initcall(mpc866ads_init);
diff --git a/arch/ppc/platforms/mpc885ads_setup.c b/arch/ppc/platforms/mpc885ads_setup.c
new file mode 100644
index 0000000..816cade
--- /dev/null
+++ b/arch/ppc/platforms/mpc885ads_setup.c
@@ -0,0 +1,387 @@
+/*arch/ppc/platforms/mpc885ads-setup.c
+ *
+ * Platform setup for the Freescale mpc885ads board
+ *
+ * Vitaly Bordug <vbordug@ru.mvista.com>
+ *
+ * Copyright 2005 MontaVista Software Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/param.h>
+#include <linux/string.h>
+#include <linux/ioport.h>
+#include <linux/device.h>
+
+#include <linux/fs_enet_pd.h>
+#include <linux/mii.h>
+
+#include <asm/delay.h>
+#include <asm/io.h>
+#include <asm/machdep.h>
+#include <asm/page.h>
+#include <asm/processor.h>
+#include <asm/system.h>
+#include <asm/time.h>
+#include <asm/ppcboot.h>
+#include <asm/8xx_immap.h>
+#include <asm/commproc.h>
+#include <asm/ppc_sys.h>
+
+extern unsigned char __res[];
+
+static void __init mpc885ads_scc_phy_init(char);
+
+static struct fs_mii_bus_info fec_mii_bus_info = {
+ .method = fsmii_fec,
+ .id = 0,
+};
+
+static struct fs_mii_bus_info scc_mii_bus_info = {
+#ifdef CONFIG_SCC_ENET_8xx_FIXED
+ .method = fsmii_fixed,
+#else
+ .method = fsmii_fec,
+#endif
+
+ .id = 0,
+};
+
+static struct fs_platform_info mpc8xx_fec_pdata[] = {
+ {
+ .rx_ring = 128,
+ .tx_ring = 16,
+ .rx_copybreak = 240,
+
+ .use_napi = 1,
+ .napi_weight = 17,
+
+ .phy_addr = 0,
+ .phy_irq = SIU_IRQ7,
+
+ .bus_info = &fec_mii_bus_info,
+ }, {
+ .rx_ring = 128,
+ .tx_ring = 16,
+ .rx_copybreak = 240,
+
+ .use_napi = 1,
+ .napi_weight = 17,
+
+ .phy_addr = 1,
+ .phy_irq = SIU_IRQ7,
+
+ .bus_info = &fec_mii_bus_info,
+ }
+};
+
+static struct fs_platform_info mpc8xx_scc_pdata = {
+ .rx_ring = 64,
+ .tx_ring = 8,
+ .rx_copybreak = 240,
+
+ .use_napi = 1,
+ .napi_weight = 17,
+
+ .phy_addr = 2,
+#ifdef CONFIG_MPC8xx_SCC_ENET_FIXED
+ .phy_irq = -1,
+#else
+ .phy_irq = SIU_IRQ7,
+#endif
+
+ .bus_info = &scc_mii_bus_info,
+};
+
+void __init board_init(void)
+{
+ volatile cpm8xx_t *cp = cpmp;
+ unsigned int *bcsr_io;
+
+#ifdef CONFIG_FS_ENET
+ immap_t *immap = (immap_t *) IMAP_ADDR;
+#endif
+ bcsr_io = ioremap(BCSR1, sizeof(unsigned long));
+
+ if (bcsr_io == NULL) {
+ printk(KERN_CRIT "Could not remap BCSR\n");
+ return;
+ }
+#ifdef CONFIG_SERIAL_CPM_SMC1
+ cp->cp_simode &= ~(0xe0000000 >> 17); /* brg1 */
+ clrbits32(bcsr_io, BCSR1_RS232EN_1);
+#else
+ setbits32(bcsr_io,BCSR1_RS232EN_1);
+ cp->cp_smc[0].smc_smcmr = 0;
+ cp->cp_smc[0].smc_smce = 0;
+#endif
+
+#ifdef CONFIG_SERIAL_CPM_SMC2
+ cp->cp_simode &= ~(0xe0000000 >> 1);
+ cp->cp_simode |= (0x20000000 >> 1); /* brg2 */
+ clrbits32(bcsr_io,BCSR1_RS232EN_2);
+#else
+ setbits32(bcsr_io,BCSR1_RS232EN_2);
+ cp->cp_smc[1].smc_smcmr = 0;
+ cp->cp_smc[1].smc_smce = 0;
+#endif
+ iounmap(bcsr_io);
+
+#ifdef CONFIG_FS_ENET
+ /* use MDC for MII (common) */
+ setbits16(&immap->im_ioport.iop_pdpar, 0x0080);
+ clrbits16(&immap->im_ioport.iop_pddir, 0x0080);
+#endif
+}
+
+static void setup_fec1_ioports(void)
+{
+ immap_t *immap = (immap_t *) IMAP_ADDR;
+
+ /* configure FEC1 pins */
+ setbits16(&immap->im_ioport.iop_papar, 0xf830);
+ setbits16(&immap->im_ioport.iop_padir, 0x0830);
+ clrbits16(&immap->im_ioport.iop_padir, 0xf000);
+ setbits32(&immap->im_cpm.cp_pbpar, 0x00001001);
+
+ clrbits32(&immap->im_cpm.cp_pbdir, 0x00001001);
+ setbits16(&immap->im_ioport.iop_pcpar, 0x000c);
+ clrbits16(&immap->im_ioport.iop_pcdir, 0x000c);
+ setbits32(&immap->im_cpm.cp_pepar, 0x00000003);
+
+ setbits32(&immap->im_cpm.cp_pedir, 0x00000003);
+ clrbits32(&immap->im_cpm.cp_peso, 0x00000003);
+ clrbits32(&immap->im_cpm.cp_cptr, 0x00000100);
+}
+
+static void setup_fec2_ioports(void)
+{
+ immap_t *immap = (immap_t *) IMAP_ADDR;
+
+ /* configure FEC2 pins */
+ setbits32(&immap->im_cpm.cp_pepar, 0x0003fffc);
+ setbits32(&immap->im_cpm.cp_pedir, 0x0003fffc);
+ setbits32(&immap->im_cpm.cp_peso, 0x00037800);
+ clrbits32(&immap->im_cpm.cp_peso, 0x000087fc);
+ clrbits32(&immap->im_cpm.cp_cptr, 0x00000080);
+}
+
+static void setup_scc3_ioports(void)
+{
+ immap_t *immap = (immap_t *) IMAP_ADDR;
+ unsigned *bcsr_io;
+
+ bcsr_io = ioremap(BCSR_ADDR, BCSR_SIZE);
+
+ if (bcsr_io == NULL) {
+ printk(KERN_CRIT "Could not remap BCSR\n");
+ return;
+ }
+
+ /* Enable the PHY.
+ */
+ setbits32(bcsr_io+4, BCSR4_ETH10_RST);
+ /* Configure port A pins for Txd and Rxd.
+ */
+ setbits16(&immap->im_ioport.iop_papar, PA_ENET_RXD | PA_ENET_TXD);
+ clrbits16(&immap->im_ioport.iop_padir, PA_ENET_RXD | PA_ENET_TXD);
+
+ /* Configure port C pins to enable CLSN and RENA.
+ */
+ clrbits16(&immap->im_ioport.iop_pcpar, PC_ENET_CLSN | PC_ENET_RENA);
+ clrbits16(&immap->im_ioport.iop_pcdir, PC_ENET_CLSN | PC_ENET_RENA);
+ setbits16(&immap->im_ioport.iop_pcso, PC_ENET_CLSN | PC_ENET_RENA);
+
+ /* Configure port E for TCLK and RCLK.
+ */
+ setbits32(&immap->im_cpm.cp_pepar, PE_ENET_TCLK | PE_ENET_RCLK);
+ clrbits32(&immap->im_cpm.cp_pepar, PE_ENET_TENA);
+ clrbits32(&immap->im_cpm.cp_pedir,
+ PE_ENET_TCLK | PE_ENET_RCLK | PE_ENET_TENA);
+ clrbits32(&immap->im_cpm.cp_peso, PE_ENET_TCLK | PE_ENET_RCLK);
+ setbits32(&immap->im_cpm.cp_peso, PE_ENET_TENA);
+
+ /* Configure Serial Interface clock routing.
+ * First, clear all SCC bits to zero, then set the ones we want.
+ */
+ clrbits32(&immap->im_cpm.cp_sicr, SICR_ENET_MASK);
+ setbits32(&immap->im_cpm.cp_sicr, SICR_ENET_CLKRT);
+
+ /* Disable Rx and Tx. SMC1 sshould be stopped if SCC3 eternet are used.
+ */
+ immap->im_cpm.cp_smc[0].smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
+ /* On the MPC885ADS SCC ethernet PHY is initialized in the full duplex mode
+ * by H/W setting after reset. SCC ethernet controller support only half duplex.
+ * This discrepancy of modes causes a lot of carrier lost errors.
+ */
+
+ /* In the original SCC enet driver the following code is placed at
+ the end of the initialization */
+ setbits32(&immap->im_cpm.cp_pepar, PE_ENET_TENA);
+ clrbits32(&immap->im_cpm.cp_pedir, PE_ENET_TENA);
+ setbits32(&immap->im_cpm.cp_peso, PE_ENET_TENA);
+
+ setbits32(bcsr_io+1, BCSR1_ETHEN);
+ iounmap(bcsr_io);
+}
+
+static void mpc885ads_fixup_enet_pdata(struct platform_device *pdev, int fs_no)
+{
+ struct fs_platform_info *fpi = pdev->dev.platform_data;
+
+ volatile cpm8xx_t *cp;
+ bd_t *bd = (bd_t *) __res;
+ char *e;
+ int i;
+
+ /* Get pointer to Communication Processor */
+ cp = cpmp;
+ switch (fs_no) {
+ case fsid_fec1:
+ fpi = &mpc8xx_fec_pdata[0];
+ fpi->init_ioports = &setup_fec1_ioports;
+ break;
+ case fsid_fec2:
+ fpi = &mpc8xx_fec_pdata[1];
+ fpi->init_ioports = &setup_fec2_ioports;
+ break;
+ case fsid_scc3:
+ fpi = &mpc8xx_scc_pdata;
+ fpi->init_ioports = &setup_scc3_ioports;
+ mpc885ads_scc_phy_init(fpi->phy_addr);
+ break;
+ default:
+ break;
+ }
+
+ pdev->dev.platform_data = fpi;
+ fpi->fs_no = fs_no;
+
+ e = (unsigned char *)&bd->bi_enetaddr;
+ for (i = 0; i < 6; i++)
+ fpi->macaddr[i] = *e++;
+
+ fpi->macaddr[5 - pdev->id]++;
+
+}
+
+static void mpc885ads_fixup_fec_enet_pdata(struct platform_device *pdev,
+ int idx)
+{
+ /* This is for FEC devices only */
+ if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-fec")))
+ return;
+ mpc885ads_fixup_enet_pdata(pdev, fsid_fec1 + pdev->id - 1);
+}
+
+static void __init mpc885ads_fixup_scc_enet_pdata(struct platform_device *pdev,
+ int idx)
+{
+ /* This is for SCC devices only */
+ if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-scc")))
+ return;
+
+ mpc885ads_fixup_enet_pdata(pdev, fsid_scc1 + pdev->id - 1);
+}
+
+/* SCC ethernet controller does not have MII management channel. FEC1 MII
+ * channel is used to communicate with the 10Mbit PHY.
+ */
+
+#define MII_ECNTRL_PINMUX 0x4
+#define FEC_ECNTRL_PINMUX 0x00000004
+#define FEC_RCNTRL_MII_MODE 0x00000004
+
+/* Make MII read/write commands.
+ */
+#define mk_mii_write(REG, VAL, PHY_ADDR) (0x50020000 | (((REG) & 0x1f) << 18) | \
+ ((VAL) & 0xffff) | ((PHY_ADDR) << 23))
+
+static void mpc885ads_scc_phy_init(char phy_addr)
+{
+ volatile immap_t *immap;
+ volatile fec_t *fecp;
+ bd_t *bd;
+
+ bd = (bd_t *) __res;
+ immap = (immap_t *) IMAP_ADDR; /* pointer to internal registers */
+ fecp = &(immap->im_cpm.cp_fec);
+
+ /* Enable MII pins of the FEC1
+ */
+ setbits16(&immap->im_ioport.iop_pdpar, 0x0080);
+ clrbits16(&immap->im_ioport.iop_pddir, 0x0080);
+ /* Set MII speed to 2.5 MHz
+ */
+ out_be32(&fecp->fec_mii_speed,
+ ((((bd->bi_intfreq + 4999999) / 2500000) / 2) & 0x3F) << 1);
+
+ /* Enable FEC pin MUX
+ */
+ setbits32(&fecp->fec_ecntrl, MII_ECNTRL_PINMUX);
+ setbits32(&fecp->fec_r_cntrl, FEC_RCNTRL_MII_MODE);
+
+ out_be32(&fecp->fec_mii_data,
+ mk_mii_write(MII_BMCR, BMCR_ISOLATE, phy_addr));
+ udelay(100);
+ out_be32(&fecp->fec_mii_data,
+ mk_mii_write(MII_ADVERTISE,
+ ADVERTISE_10HALF | ADVERTISE_CSMA, phy_addr));
+ udelay(100);
+
+ /* Disable FEC MII settings
+ */
+ clrbits32(&fecp->fec_ecntrl, MII_ECNTRL_PINMUX);
+ clrbits32(&fecp->fec_r_cntrl, FEC_RCNTRL_MII_MODE);
+ out_be32(&fecp->fec_mii_speed, 0);
+}
+
+static int mpc885ads_platform_notify(struct device *dev)
+{
+
+ static const struct platform_notify_dev_map dev_map[] = {
+ {
+ .bus_id = "fsl-cpm-fec",
+ .rtn = mpc885ads_fixup_fec_enet_pdata,
+ },
+ {
+ .bus_id = "fsl-cpm-scc",
+ .rtn = mpc885ads_fixup_scc_enet_pdata,
+ },
+ {
+ .bus_id = NULL
+ }
+ };
+
+ platform_notify_map(dev_map,dev);
+
+}
+
+int __init mpc885ads_init(void)
+{
+ printk(KERN_NOTICE "mpc885ads: Init\n");
+
+ platform_notify = mpc885ads_platform_notify;
+
+ ppc_sys_device_initfunc();
+
+ ppc_sys_device_enable(MPC8xx_CPM_FEC1);
+
+#ifdef CONFIG_MPC8xx_SECOND_ETH_SCC3
+ ppc_sys_device_enable(MPC8xx_CPM_SCC1);
+
+#endif
+#ifdef CONFIG_MPC8xx_SECOND_ETH_FEC2
+ ppc_sys_device_enable(MPC8xx_CPM_FEC2);
+#endif
+
+ return 0;
+}
+
+arch_initcall(mpc885ads_init);
diff --git a/arch/ppc/platforms/pq2ads.h b/arch/ppc/platforms/pq2ads.h
index 067d9a5..6b26dd3 100644
--- a/arch/ppc/platforms/pq2ads.h
+++ b/arch/ppc/platforms/pq2ads.h
@@ -13,6 +13,10 @@
#include <asm/ppcboot.h>
+#if defined(CONFIG_ADS8272)
+#define BOARD_CHIP_NAME "8272"
+#endif
+
/* Memory map is configured by the PROM startup.
* We just map a few things we need. The CSR is actually 4 byte-wide
* registers that can be accessed as 8-, 16-, or 32-bit values.
diff --git a/arch/ppc/platforms/pq2ads_pd.h b/arch/ppc/platforms/pq2ads_pd.h
new file mode 100644
index 0000000..8f14a43
--- /dev/null
+++ b/arch/ppc/platforms/pq2ads_pd.h
@@ -0,0 +1,114 @@
+#ifndef __PQ2ADS_PD_H
+#define __PQ2ADS_PD_H
+/*
+ * arch/ppc/platforms/82xx/pq2ads_pd.h
+ *
+ * Some defines for MPC82xx board-specific PlatformDevice descriptions
+ *
+ * 2005 (c) MontaVista Software, Inc.
+ * Vitaly Bordug <vbordug@ru.mvista.com>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/* FCC1 Clock Source Configuration. These can be redefined in the board specific file.
+ Can only choose from CLK9-12 */
+
+#define F1_RXCLK 11
+#define F1_TXCLK 10
+
+/* FCC2 Clock Source Configuration. These can be redefined in the board specific file.
+ Can only choose from CLK13-16 */
+#define F2_RXCLK 15
+#define F2_TXCLK 16
+
+/* FCC3 Clock Source Configuration. These can be redefined in the board specific file.
+ Can only choose from CLK13-16 */
+#define F3_RXCLK 13
+#define F3_TXCLK 14
+
+/* Automatically generates register configurations */
+#define PC_CLK(x) ((uint)(1<<(x-1))) /* FCC CLK I/O ports */
+
+#define CMXFCR_RF1CS(x) ((uint)((x-5)<<27)) /* FCC1 Receive Clock Source */
+#define CMXFCR_TF1CS(x) ((uint)((x-5)<<24)) /* FCC1 Transmit Clock Source */
+#define CMXFCR_RF2CS(x) ((uint)((x-9)<<19)) /* FCC2 Receive Clock Source */
+#define CMXFCR_TF2CS(x) ((uint)((x-9)<<16)) /* FCC2 Transmit Clock Source */
+#define CMXFCR_RF3CS(x) ((uint)((x-9)<<11)) /* FCC3 Receive Clock Source */
+#define CMXFCR_TF3CS(x) ((uint)((x-9)<<8)) /* FCC3 Transmit Clock Source */
+
+#define PC_F1RXCLK PC_CLK(F1_RXCLK)
+#define PC_F1TXCLK PC_CLK(F1_TXCLK)
+#define CMX1_CLK_ROUTE (CMXFCR_RF1CS(F1_RXCLK) | CMXFCR_TF1CS(F1_TXCLK))
+#define CMX1_CLK_MASK ((uint)0xff000000)
+
+#define PC_F2RXCLK PC_CLK(F2_RXCLK)
+#define PC_F2TXCLK PC_CLK(F2_TXCLK)
+#define CMX2_CLK_ROUTE (CMXFCR_RF2CS(F2_RXCLK) | CMXFCR_TF2CS(F2_TXCLK))
+#define CMX2_CLK_MASK ((uint)0x00ff0000)
+
+#define PC_F3RXCLK PC_CLK(F3_RXCLK)
+#define PC_F3TXCLK PC_CLK(F3_TXCLK)
+#define CMX3_CLK_ROUTE (CMXFCR_RF3CS(F3_RXCLK) | CMXFCR_TF3CS(F3_TXCLK))
+#define CMX3_CLK_MASK ((uint)0x0000ff00)
+
+/* I/O Pin assignment for FCC1. I don't yet know the best way to do this,
+ * but there is little variation among the choices.
+ */
+#define PA1_COL 0x00000001U
+#define PA1_CRS 0x00000002U
+#define PA1_TXER 0x00000004U
+#define PA1_TXEN 0x00000008U
+#define PA1_RXDV 0x00000010U
+#define PA1_RXER 0x00000020U
+#define PA1_TXDAT 0x00003c00U
+#define PA1_RXDAT 0x0003c000U
+#define PA1_PSORA0 (PA1_RXDAT | PA1_TXDAT)
+#define PA1_PSORA1 (PA1_COL | PA1_CRS | PA1_TXER | PA1_TXEN | \
+ PA1_RXDV | PA1_RXER)
+#define PA1_DIRA0 (PA1_RXDAT | PA1_CRS | PA1_COL | PA1_RXER | PA1_RXDV)
+#define PA1_DIRA1 (PA1_TXDAT | PA1_TXEN | PA1_TXER)
+
+
+/* I/O Pin assignment for FCC2. I don't yet know the best way to do this,
+ * but there is little variation among the choices.
+ */
+#define PB2_TXER 0x00000001U
+#define PB2_RXDV 0x00000002U
+#define PB2_TXEN 0x00000004U
+#define PB2_RXER 0x00000008U
+#define PB2_COL 0x00000010U
+#define PB2_CRS 0x00000020U
+#define PB2_TXDAT 0x000003c0U
+#define PB2_RXDAT 0x00003c00U
+#define PB2_PSORB0 (PB2_RXDAT | PB2_TXDAT | PB2_CRS | PB2_COL | \
+ PB2_RXER | PB2_RXDV | PB2_TXER)
+#define PB2_PSORB1 (PB2_TXEN)
+#define PB2_DIRB0 (PB2_RXDAT | PB2_CRS | PB2_COL | PB2_RXER | PB2_RXDV)
+#define PB2_DIRB1 (PB2_TXDAT | PB2_TXEN | PB2_TXER)
+
+
+/* I/O Pin assignment for FCC3. I don't yet know the best way to do this,
+ * but there is little variation among the choices.
+ */
+#define PB3_RXDV 0x00004000U
+#define PB3_RXER 0x00008000U
+#define PB3_TXER 0x00010000U
+#define PB3_TXEN 0x00020000U
+#define PB3_COL 0x00040000U
+#define PB3_CRS 0x00080000U
+#define PB3_TXDAT 0x0f000000U
+#define PB3_RXDAT 0x00f00000U
+#define PB3_PSORB0 (PB3_RXDAT | PB3_TXDAT | PB3_CRS | PB3_COL | \
+ PB3_RXER | PB3_RXDV | PB3_TXER | PB3_TXEN)
+#define PB3_PSORB1 0
+#define PB3_DIRB0 (PB3_RXDAT | PB3_CRS | PB3_COL | PB3_RXER | PB3_RXDV)
+#define PB3_DIRB1 (PB3_TXDAT | PB3_TXEN | PB3_TXER)
+
+#define FCC_MEM_OFFSET(x) (CPM_FCC_SPECIAL_BASE + (x*128))
+#define FCC1_MEM_OFFSET FCC_MEM_OFFSET(0)
+#define FCC2_MEM_OFFSET FCC_MEM_OFFSET(1)
+
+#endif
diff --git a/arch/ppc/syslib/ppc_sys.c b/arch/ppc/syslib/ppc_sys.c
index e3856e7..9182a36 100644
--- a/arch/ppc/syslib/ppc_sys.c
+++ b/arch/ppc/syslib/ppc_sys.c
@@ -238,7 +238,7 @@ void ppc_sys_device_setfunc(enum ppc_sys
else
*s = 0;
} else if (func != PPC_SYS_FUNC_DUMMY) {
- /* do assignment if it is not just "enable" request */
+ /* do assignment if it is not just "clear" request */
sprintf(tmp, "%s:%s", name, ppc_sys_func_names[func]);
strlcpy(name, tmp, BUS_ID_SIZE);
}
@@ -294,7 +294,7 @@ static int __init ppc_sys_init(void)
for (i = 0; i < cur_ppc_sys_spec->num_devices; i++) {
dev_id = cur_ppc_sys_spec->device_list[i];
- if ((dev_id != -1) ||
+ if ((dev_id != -1) &&
(cur_ppc_sys_spec->config[dev_id] & PPC_SYS_CONFIG_ENABED)) {
if (ppc_sys_device_fixup != NULL)
ppc_sys_device_fixup(&ppc_sys_platform_devices
diff --git a/drivers/base/platform.c b/drivers/base/platform.c
index 8827daf..ce551b5 100644
--- a/drivers/base/platform.c
+++ b/drivers/base/platform.c
@@ -266,7 +266,7 @@ int platform_device_add(struct platform_
}
}
- pr_debug("Registering platform device '%s'. Parent at %s\n",
+ pr_info("Registering platform device '%s'. Parent at %s\n",
pdev->dev.bus_id, pdev->dev.parent->bus_id);
ret = device_register(&pdev->dev);
^ permalink raw reply related
* [PATCH 1/2] ppc32: Make platform devices being able to assign functions (resend)
From: Vitaly Bordug @ 2005-12-28 20:04 UTC (permalink / raw)
To: Kumar Gala; +Cc: linuxppc-embedded list
Implemented by modification of the .name field of the platform device,
when PDs with the
same names are to be used within different drivers, as
<device_name> -> <device_name>:<function>
Corresponding drivers should change the .name in struct device_driver to
reflect upper of course.
Also helper platform_notify_map function added, making assignment of
board-specific platform_info more consistent and generic.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
---
arch/ppc/syslib/ppc_sys.c | 165 ++++++++++++++++++++++++++++++++++++++++++++-
include/asm-ppc/mpc10x.h | 1
include/asm-ppc/mpc52xx.h | 1
include/asm-ppc/mpc8260.h | 1
include/asm-ppc/mpc83xx.h | 1
include/asm-ppc/mpc85xx.h | 1
include/asm-ppc/mpc8xx.h | 1
include/asm-ppc/ppc_sys.h | 26 +++++++
8 files changed, 194 insertions(+), 3 deletions(-)
diff --git a/arch/ppc/syslib/ppc_sys.c b/arch/ppc/syslib/ppc_sys.c
index c0b93c4..e3856e7 100644
--- a/arch/ppc/syslib/ppc_sys.c
+++ b/arch/ppc/syslib/ppc_sys.c
@@ -15,11 +15,22 @@
*/
#include <linux/string.h>
+#include <linux/bootmem.h>
#include <asm/ppc_sys.h>
int (*ppc_sys_device_fixup) (struct platform_device * pdev);
static int ppc_sys_inited;
+static int ppc_sys_func_inited;
+
+static const char *ppc_sys_func_names[] = {
+ [PPC_SYS_FUNC_DUMMY] = "dummy",
+ [PPC_SYS_FUNC_ETH] = "eth",
+ [PPC_SYS_FUNC_UART] = "uart",
+ [PPC_SYS_FUNC_HLDC] = "hldc",
+ [PPC_SYS_FUNC_USB] = "usb",
+ [PPC_SYS_FUNC_IRDA] = "irda",
+};
void __init identify_ppc_sys_by_id(u32 id)
{
@@ -38,13 +49,13 @@ void __init identify_ppc_sys_by_id(u32 i
void __init identify_ppc_sys_by_name(char *name)
{
unsigned int i = 0;
- while (ppc_sys_specs[i].ppc_sys_name[0])
- {
+ while (ppc_sys_specs[i].ppc_sys_name[0]) {
if (!strcmp(ppc_sys_specs[i].ppc_sys_name, name))
break;
i++;
}
cur_ppc_sys_spec = &ppc_sys_specs[i];
+
return;
}
@@ -128,6 +139,153 @@ void ppc_sys_device_remove(enum ppc_sys_
}
}
+/* Platform-notify mapping
+ * Helper function for BSP code to assign board-specific platfom-divice bits
+ */
+
+void platform_notify_map(const struct platform_notify_dev_map *map,
+ struct device *dev)
+{
+ struct platform_device *pdev;
+ int len, idx;
+ const char *s;
+
+ /* do nothing if no device or no bus_id */
+ if (!dev || !dev->bus_id)
+ return;
+
+ /* call per device map */
+ while (map->bus_id != NULL) {
+ idx = -1;
+ s = strrchr(dev->bus_id, '.');
+ if (s != NULL)
+ idx = (int)simple_strtol(s + 1, NULL, 10);
+ else
+ s = dev->bus_id;
+
+ len = s - dev->bus_id;
+
+ if (!strncmp(dev->bus_id, map->bus_id, len)) {
+ pdev = container_of(dev, struct platform_device, dev);
+ map->rtn(pdev, idx);
+ }
+ map++;
+ }
+}
+
+/*
+ Function assignment stuff.
+ Intended to work as follows:
+ the device name defined in foo_devices.c will be concatenated with :"func",
+ where func is string map of respective function from platfom_device_func enum
+
+ The PPC_SYS_FUNC_DUMMY function is intended to remove all assignments, making the device to appear
+ in platform bus with unmodified name.
+ */
+
+/*
+ Here we'll replace .name pointers with fixed-lenght strings
+ Hereby, this should be called *before* any func stuff triggeded.
+ */
+void ppc_sys_device_initfunc(void)
+{
+ int i;
+ const char *name;
+ static char new_names[NUM_PPC_SYS_DEVS][BUS_ID_SIZE];
+ enum ppc_sys_devices cur_dev;
+
+ /* If inited yet, do nothing */
+ if (ppc_sys_func_inited)
+ return;
+
+ for (i = 0; i < cur_ppc_sys_spec->num_devices; i++) {
+ if ((cur_dev = cur_ppc_sys_spec->device_list[i]) < 0)
+ continue;
+
+ if (ppc_sys_platform_devices[cur_dev].name) {
+ /*backup name */
+ name = ppc_sys_platform_devices[cur_dev].name;
+ strlcpy(new_names[i], name, BUS_ID_SIZE);
+ ppc_sys_platform_devices[cur_dev].name = new_names[i];
+ }
+ }
+
+ ppc_sys_func_inited = 1;
+}
+
+/*The "engine" of the func stuff. Here we either concat specified function string description
+ to the name, or remove it if PPC_SYS_FUNC_DUMMY parameter is passed here*/
+void ppc_sys_device_setfunc(enum ppc_sys_devices dev,
+ enum platform_device_func func)
+{
+ char *s;
+ char *name = (char *)ppc_sys_platform_devices[dev].name;
+ char tmp[BUS_ID_SIZE];
+
+ if (!ppc_sys_func_inited) {
+ printk(KERN_ERR "Unable to alter function - not inited!\n");
+ return;
+ }
+
+ if (ppc_sys_inited) {
+ platform_device_unregister(&ppc_sys_platform_devices[dev]);
+ }
+
+ if ((s = (char *)strchr(name, ':')) != NULL) { /* reassign */
+ /* Either change the name after ':' or remove func modifications */
+ if (func != PPC_SYS_FUNC_DUMMY)
+ strlcpy(s + 1, ppc_sys_func_names[func], BUS_ID_SIZE);
+ else
+ *s = 0;
+ } else if (func != PPC_SYS_FUNC_DUMMY) {
+ /* do assignment if it is not just "enable" request */
+ sprintf(tmp, "%s:%s", name, ppc_sys_func_names[func]);
+ strlcpy(name, tmp, BUS_ID_SIZE);
+ }
+
+ if (ppc_sys_inited) {
+ platform_device_register(&ppc_sys_platform_devices[dev]);
+ }
+}
+
+void ppc_sys_device_disable(enum ppc_sys_devices dev)
+{
+ BUG_ON(cur_ppc_sys_spec == NULL);
+
+ /*Check if it is enabled*/
+ if(cur_ppc_sys_spec->config[dev] & PPC_SYS_CONFIG_ENABED) {
+ if (ppc_sys_inited) {
+ platform_device_unregister(&ppc_sys_platform_devices[dev]);
+ }
+ cur_ppc_sys_spec->config[dev] &= ~PPC_SYS_CONFIG_ENABED;
+ }
+}
+
+void ppc_sys_device_enable(enum ppc_sys_devices dev)
+{
+ BUG_ON(cur_ppc_sys_spec == NULL);
+
+ /*Check if it is disabled*/
+ if(!(cur_ppc_sys_spec->config[dev] & PPC_SYS_CONFIG_ENABED)) {
+ if (ppc_sys_inited) {
+ platform_device_register(&ppc_sys_platform_devices[dev]);
+ }
+ cur_ppc_sys_spec->config[dev] |= PPC_SYS_CONFIG_ENABED;
+ }
+
+}
+
+void ppc_sys_device_enable_all(enum platform_device_func func)
+{
+ enum ppc_sys_devices cur_dev;
+ int i;
+
+ for (i = 0; i < cur_ppc_sys_spec->num_devices; i++) {
+ cur_dev = cur_ppc_sys_spec->device_list[i];
+ ppc_sys_device_enable(cur_dev);
+ }
+}
+
static int __init ppc_sys_init(void)
{
unsigned int i, dev_id, ret = 0;
@@ -136,7 +294,8 @@ static int __init ppc_sys_init(void)
for (i = 0; i < cur_ppc_sys_spec->num_devices; i++) {
dev_id = cur_ppc_sys_spec->device_list[i];
- if (dev_id != -1) {
+ if ((dev_id != -1) ||
+ (cur_ppc_sys_spec->config[dev_id] & PPC_SYS_CONFIG_ENABED)) {
if (ppc_sys_device_fixup != NULL)
ppc_sys_device_fixup(&ppc_sys_platform_devices
[dev_id]);
diff --git a/include/asm-ppc/mpc10x.h b/include/asm-ppc/mpc10x.h
index 77b1e09..976ad3d 100644
--- a/include/asm-ppc/mpc10x.h
+++ b/include/asm-ppc/mpc10x.h
@@ -165,6 +165,7 @@ enum ppc_sys_devices {
MPC10X_DMA1,
MPC10X_UART0,
MPC10X_UART1,
+ NUM_PPC_SYS_DEVS,
};
int mpc10x_bridge_init(struct pci_controller *hose,
diff --git a/include/asm-ppc/mpc52xx.h b/include/asm-ppc/mpc52xx.h
index e5f80c2..b2cb44f 100644
--- a/include/asm-ppc/mpc52xx.h
+++ b/include/asm-ppc/mpc52xx.h
@@ -49,6 +49,7 @@ enum ppc_sys_devices {
MPC52xx_ATA,
MPC52xx_I2C1,
MPC52xx_I2C2,
+ NUM_PPC_SYS_DEVS,
};
diff --git a/include/asm-ppc/mpc8260.h b/include/asm-ppc/mpc8260.h
index 3214526..6ba69a8 100644
--- a/include/asm-ppc/mpc8260.h
+++ b/include/asm-ppc/mpc8260.h
@@ -83,6 +83,7 @@ enum ppc_sys_devices {
MPC82xx_CPM_SMC2,
MPC82xx_CPM_USB,
MPC82xx_SEC1,
+ NUM_PPC_SYS_DEVS,
};
#ifndef __ASSEMBLY__
diff --git a/include/asm-ppc/mpc83xx.h b/include/asm-ppc/mpc83xx.h
index 7cdf60f..3c23fc4 100644
--- a/include/asm-ppc/mpc83xx.h
+++ b/include/asm-ppc/mpc83xx.h
@@ -108,6 +108,7 @@ enum ppc_sys_devices {
MPC83xx_USB2_DR,
MPC83xx_USB2_MPH,
MPC83xx_MDIO,
+ NUM_PPC_SYS_DEVS,
};
#endif /* CONFIG_83xx */
diff --git a/include/asm-ppc/mpc85xx.h b/include/asm-ppc/mpc85xx.h
index 9d14bae..2a77884 100644
--- a/include/asm-ppc/mpc85xx.h
+++ b/include/asm-ppc/mpc85xx.h
@@ -135,6 +135,7 @@ enum ppc_sys_devices {
MPC85xx_eTSEC4,
MPC85xx_IIC2,
MPC85xx_MDIO,
+ NUM_PPC_SYS_DEVS,
};
/* Internal interrupts are all Level Sensitive, and Positive Polarity */
diff --git a/include/asm-ppc/mpc8xx.h b/include/asm-ppc/mpc8xx.h
index 46f159c..90e3d59 100644
--- a/include/asm-ppc/mpc8xx.h
+++ b/include/asm-ppc/mpc8xx.h
@@ -111,6 +111,7 @@ enum ppc_sys_devices {
MPC8xx_CPM_SMC1,
MPC8xx_CPM_SMC2,
MPC8xx_CPM_USB,
+ NUM_PPC_SYS_DEVS,
};
#ifndef BOARD_CHIP_NAME
diff --git a/include/asm-ppc/ppc_sys.h b/include/asm-ppc/ppc_sys.h
index 83d8c77..e6f83ad 100644
--- a/include/asm-ppc/ppc_sys.h
+++ b/include/asm-ppc/ppc_sys.h
@@ -44,9 +44,26 @@ struct ppc_sys_spec {
u32 value;
u32 num_devices;
char *ppc_sys_name;
+ u8 config[NUM_PPC_SYS_DEVS];
enum ppc_sys_devices *device_list;
};
+struct platform_notify_dev_map {
+ const char *bus_id;
+ void (*rtn)(struct platform_device * pdev, int idx);
+};
+
+enum platform_device_func {
+ PPC_SYS_FUNC_DUMMY = 0,
+ PPC_SYS_FUNC_ETH = 1,
+ PPC_SYS_FUNC_UART = 2,
+ PPC_SYS_FUNC_HLDC = 3,
+ PPC_SYS_FUNC_USB = 4,
+ PPC_SYS_FUNC_IRDA = 5,
+};
+
+#define PPC_SYS_CONFIG_ENABED 1
+
/* describes all specific chips and which devices they have on them */
extern struct ppc_sys_spec ppc_sys_specs[];
extern struct ppc_sys_spec *cur_ppc_sys_spec;
@@ -72,5 +89,14 @@ extern void *ppc_sys_get_pdata(enum ppc_
/* remove a device from the system */
extern void ppc_sys_device_remove(enum ppc_sys_devices dev);
+/*Function assignment stuff*/
+void ppc_sys_device_initfunc(void);
+void ppc_sys_device_setfunc(enum ppc_sys_devices dev,
+ enum platform_device_func func);
+void ppc_sys_device_set_func_all(enum platform_device_func func);
+
+void platform_notify_map(const struct platform_notify_dev_map *map,
+ struct device *dev);
+
#endif /* __ASM_PPC_SYS_H */
#endif /* __KERNEL__ */
^ permalink raw reply related
* [PATCH 2/2] ppc32: MPC885ADS, MPC866ADS and MPC8272ADS-specific platform stuff for fs_enet
From: Vitaly Bordug @ 2005-12-28 19:23 UTC (permalink / raw)
To: Marcelo Tosatti; +Cc: linuxppc-embedded list
In-Reply-To: <20051228191803.30378.93344.stgit@vitb.dev.rtsoft.ru>
Added proper ppc_sys identification and fs_platform_info's for MPC 885ADS,
866ADS and 8272ADS, utilizing function assignment to remove/do not use
platform devices which conflict with PD-incompatible drivers.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
---
arch/ppc/Kconfig | 47 ++++
arch/ppc/platforms/Makefile | 4
arch/ppc/platforms/fads.h | 2
arch/ppc/platforms/mpc8272ads_setup.c | 236 ++++++++++++++++++++
arch/ppc/platforms/mpc866ads_setup.c | 270 +++++++++++++++++++++++
arch/ppc/platforms/mpc885ads_setup.c | 387 +++++++++++++++++++++++++++++++++
arch/ppc/platforms/pq2ads.h | 4
arch/ppc/platforms/pq2ads_pd.h | 114 ++++++++++
arch/ppc/syslib/ppc_sys.c | 4
drivers/base/platform.c | 2
10 files changed, 1066 insertions(+), 4 deletions(-)
diff --git a/arch/ppc/Kconfig b/arch/ppc/Kconfig
index cc3f64c..ac32793 100644
--- a/arch/ppc/Kconfig
+++ b/arch/ppc/Kconfig
@@ -506,6 +506,53 @@ config WINCEPT
endchoice
+menu "Freescale Ethernet driver platform-specific options"
+ depends on FS_ENET
+
+ config MPC8xx_SECOND_ETH
+ bool "Second Ethernet channel"
+ depends on (MPC885ADS || MPC86XADS)
+ default y
+ help
+ This enables support for second Ethernet on MPC885ADS and MPC86xADS boards.
+ The latter will use SCC1, for 885ADS you can select it below.
+
+ choice
+ prompt "Second Ethernet channel"
+ depends on MPC8xx_SECOND_ETH
+ default MPC8xx_SECOND_ETH_FEC2
+
+ config MPC8xx_SECOND_ETH_FEC2
+ bool "FEC2"
+ depends on MPC885ADS
+ help
+ Enable FEC2 to serve as 2-nd Ethernet channel. Note that SMC2
+ (often 2-nd UART) will not work if this is enabled.
+
+ config MPC8xx_SECOND_ETH_SCC1
+ bool "SCC1"
+ depends on MPC86XADS
+ select MPC8xx_SCC_ENET_FIXED
+ help
+ Enable SCC1 to serve as 2-nd Ethernet channel. Note that SMC1
+ (often 1-nd UART) will not work if this is enabled.
+
+ config MPC8xx_SECOND_ETH_SCC3
+ bool "SCC3"
+ depends on MPC885ADS
+ help
+ Enable SCC3 to serve as 2-nd Ethernet channel. Note that SMC1
+ (often 1-nd UART) will not work if this is enabled.
+
+ endchoice
+
+ config MPC8xx_SCC_ENET_FIXED
+ depends on MPC8xx_SECOND_ETH_SCC
+ default n
+ bool "Use fixed MII-less mode for SCC Ethernet"
+
+endmenu
+
choice
prompt "Machine Type"
depends on 6xx || POWER3 || POWER4
diff --git a/arch/ppc/platforms/Makefile b/arch/ppc/platforms/Makefile
index 7c5cdab..ee50b0d 100644
--- a/arch/ppc/platforms/Makefile
+++ b/arch/ppc/platforms/Makefile
@@ -22,6 +22,8 @@ ifeq ($(CONFIG_PPC_PMAC),y)
obj-$(CONFIG_NVRAM) += pmac_nvram.o
obj-$(CONFIG_CPU_FREQ_PMAC) += pmac_cpufreq.o
endif
+
+obj-$(CONFIG_ADS8272) += mpc8272ads_setup.o
obj-$(CONFIG_PMAC_BACKLIGHT) += pmac_backlight.o
obj-$(CONFIG_PREP_RESIDUAL) += residual.o
obj-$(CONFIG_PQ2ADS) += pq2ads.o
@@ -45,6 +47,8 @@ obj-$(CONFIG_SBC82xx) += sbc82xx.o
obj-$(CONFIG_SPRUCE) += spruce.o
obj-$(CONFIG_LITE5200) += lite5200.o
obj-$(CONFIG_EV64360) += ev64360.o
+obj-$(CONFIG_MPC86XADS) += mpc866ads_setup.o
+obj-$(CONFIG_MPC885ADS) += mpc885ads_setup.o
ifeq ($(CONFIG_SMP),y)
obj-$(CONFIG_PPC_PMAC) += pmac_smp.o
diff --git a/arch/ppc/platforms/fads.h b/arch/ppc/platforms/fads.h
index a48fb8d..e1c0b1b 100644
--- a/arch/ppc/platforms/fads.h
+++ b/arch/ppc/platforms/fads.h
@@ -112,7 +112,7 @@
/* CPM Ethernet through SCC1 or SCC2 */
-#ifdef CONFIG_SCC1_ENET /* Probably 860 variant */
+#if defined(CONFIG_SCC1_ENET) || defined(CONFIG_MPC8xx_SECOND_ETH_SCC1) /* Probably 860 variant */
/* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC1 use.
* TCLK - CLK1, RCLK - CLK2.
diff --git a/arch/ppc/platforms/mpc8272ads_setup.c b/arch/ppc/platforms/mpc8272ads_setup.c
new file mode 100644
index 0000000..e45b91a
--- /dev/null
+++ b/arch/ppc/platforms/mpc8272ads_setup.c
@@ -0,0 +1,236 @@
+/*
+ * arch/ppc/platforms/82xx/pq2ads_pd.c
+ *
+ * MPC82xx Board-specific PlatformDevice descriptions
+ *
+ * 2005 (c) MontaVista Software, Inc.
+ * Vitaly Bordug <vbordug@ru.mvista.com>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/ioport.h>
+#include <linux/fs_enet_pd.h>
+#include <linux/platform_device.h>
+
+#include <asm/io.h>
+#include <asm/mpc8260.h>
+#include <asm/cpm2.h>
+#include <asm/immap_cpm2.h>
+#include <asm/irq.h>
+#include <asm/ppc_sys.h>
+#include <asm/ppcboot.h>
+
+#include "pq2ads_pd.h"
+
+static void init_fcc1_ioports(void);
+static void init_fcc2_ioports(void);
+
+static struct fs_mii_bus_info mii_bus_info = {
+ .method = fsmii_bitbang,
+ .id = 0,
+ .i.bitbang = {
+ .mdio_port = fsiop_portc,
+ .mdio_bit = 18,
+ .mdc_port = fsiop_portc,
+ .mdc_bit = 19,
+ .delay = 1,
+ },
+};
+
+static struct fs_platform_info mpc82xx_fcc1_pdata = {
+ .fs_no = fsid_fcc1,
+ .cp_page = CPM_CR_FCC1_PAGE,
+ .cp_block = CPM_CR_FCC1_SBLOCK,
+ .clk_trx = (PC_F1RXCLK | PC_F1TXCLK),
+ .clk_route = CMX1_CLK_ROUTE,
+ .clk_mask = CMX1_CLK_MASK,
+ .init_ioports = init_fcc1_ioports,
+
+ .phy_addr = 0,
+#ifdef PHY_INTERRUPT
+ .phy_irq = PHY_INTERRUPT,
+#else
+ .phy_irq = -1;
+#endif
+ .mem_offset = FCC1_MEM_OFFSET,
+ .bus_info = &mii_bus_info,
+ .rx_ring = 32,
+ .tx_ring = 32,
+ .rx_copybreak = 240,
+ .use_napi = 0,
+ .napi_weight = 17,
+};
+
+static struct fs_platform_info mpc82xx_fcc2_pdata = {
+ .fs_no = fsid_fcc2,
+ .cp_page = CPM_CR_FCC2_PAGE,
+ .cp_block = CPM_CR_FCC2_SBLOCK,
+ .clk_trx = (PC_F2RXCLK | PC_F2TXCLK),
+ .clk_route = CMX2_CLK_ROUTE,
+ .clk_mask = CMX2_CLK_MASK,
+ .init_ioports = init_fcc2_ioports,
+
+ .phy_addr = 3,
+#ifdef PHY_INTERRUPT
+ .phy_irq = PHY_INTERRUPT,
+#else
+ .phy_irq = -1;
+#endif
+ .mem_offset = FCC2_MEM_OFFSET,
+ .bus_info = &mii_bus_info,
+ .rx_ring = 32,
+ .tx_ring = 32,
+ .rx_copybreak = 240,
+ .use_napi = 0,
+ .napi_weight = 17,
+};
+
+static void init_fcc1_ioports(void)
+{
+ struct io_port *io;
+ u32 tempval;
+ cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t));
+ u32 *bcsr = ioremap(BCSR_ADDR+4, sizeof(u32));
+
+ io = &immap->im_ioport;
+
+ /* Enable the PHY */
+ clrbits32(bcsr, BCSR1_FETHIEN);
+ setbits32(bcsr, BCSR1_FETH_RST);
+
+ /* FCC1 pins are on port A/C. */
+ /* Configure port A and C pins for FCC1 Ethernet. */
+
+ tempval = in_be32(&io->iop_pdira);
+ tempval &= ~PA1_DIRA0;
+ tempval |= PA1_DIRA1;
+ out_be32(&io->iop_pdira, tempval);
+
+ tempval = in_be32(&io->iop_psora);
+ tempval &= ~PA1_PSORA0;
+ tempval |= PA1_PSORA1;
+ out_be32(&io->iop_psora, tempval);
+
+ setbits32(&io->iop_ppara,PA1_DIRA0 | PA1_DIRA1);
+
+ /* Alter clocks */
+ tempval = PC_F1TXCLK|PC_F1RXCLK;
+
+ clrbits32(&io->iop_psorc, tempval);
+ clrbits32(&io->iop_pdirc, tempval);
+ setbits32(&io->iop_pparc, tempval);
+
+ clrbits32(&immap->im_cpmux.cmx_fcr, CMX1_CLK_MASK);
+ setbits32(&immap->im_cpmux.cmx_fcr, CMX1_CLK_ROUTE);
+ iounmap(bcsr);
+ iounmap(immap);
+}
+
+static void init_fcc2_ioports(void)
+{
+ cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t));
+ u32 *bcsr = ioremap(BCSR_ADDR+12, sizeof(u32));
+
+ struct io_port *io;
+ u32 tempval;
+
+ immap = cpm2_immr;
+
+ io = &immap->im_ioport;
+
+ /* Enable the PHY */
+ clrbits32(bcsr, BCSR3_FETHIEN2);
+ setbits32(bcsr, BCSR3_FETH2_RST);
+
+ /* FCC2 are port B/C. */
+ /* Configure port A and C pins for FCC2 Ethernet. */
+
+ tempval = in_be32(&io->iop_pdirb);
+ tempval &= ~PB2_DIRB0;
+ tempval |= PB2_DIRB1;
+ out_be32(&io->iop_pdirb, tempval);
+
+ tempval = in_be32(&io->iop_psorb);
+ tempval &= ~PB2_PSORB0;
+ tempval |= PB2_PSORB1;
+ out_be32(&io->iop_psorb, tempval);
+
+ setbits32(&io->iop_pparb,PB2_DIRB0 | PB2_DIRB1);
+
+ tempval = PC_F2RXCLK|PC_F2TXCLK;
+
+ /* Alter clocks */
+ clrbits32(&io->iop_psorc,tempval);
+ clrbits32(&io->iop_pdirc,tempval);
+ setbits32(&io->iop_pparc,tempval);
+
+ clrbits32(&immap->im_cpmux.cmx_fcr, CMX2_CLK_MASK);
+ setbits32(&immap->im_cpmux.cmx_fcr, CMX2_CLK_ROUTE);
+
+ iounmap(bcsr);
+ iounmap(immap);
+}
+
+
+static void __init mpc8272ads_fixup_enet_pdata(struct platform_device *pdev,
+ int idx)
+{
+ bd_t* bi = (void*)__res;
+ int fs_no = fsid_fcc1+pdev->id-1;
+
+ mpc82xx_fcc1_pdata.dpram_offset = mpc82xx_fcc2_pdata.dpram_offset = (u32)cpm2_immr->im_dprambase;
+ mpc82xx_fcc1_pdata.fcc_regs_c = mpc82xx_fcc2_pdata.fcc_regs_c = (u32)cpm2_immr->im_fcc_c;
+
+ switch(fs_no) {
+ case fsid_fcc1:
+ memcpy(&mpc82xx_fcc1_pdata.macaddr,bi->bi_enetaddr,6);
+ pdev->dev.platform_data = &mpc82xx_fcc1_pdata;
+ break;
+ case fsid_fcc2:
+ memcpy(&mpc82xx_fcc2_pdata.macaddr,bi->bi_enetaddr,6);
+ mpc82xx_fcc2_pdata.macaddr[5] ^= 1;
+ pdev->dev.platform_data = &mpc82xx_fcc2_pdata;
+ break;
+ }
+ printk("all\n");
+}
+
+static int mpc8272ads_platform_notify(struct device *dev)
+{
+ static const struct platform_notify_dev_map dev_map[] = {
+ {
+ .bus_id = "fsl-cpm-fcc",
+ .rtn = mpc8272ads_fixup_enet_pdata
+ },
+ {
+ .bus_id = NULL
+ }
+ };
+ platform_notify_map(dev_map,dev);
+
+ return 0;
+
+}
+
+int __init mpc8272ads_init(void)
+{
+ printk(KERN_NOTICE "mpc8272ads: Init\n");
+
+ platform_notify = mpc8272ads_platform_notify;
+
+ ppc_sys_device_initfunc();
+
+ ppc_sys_device_enable(MPC82xx_CPM_FCC1);
+ ppc_sys_device_enable(MPC82xx_CPM_FCC2);
+
+ return 0;
+}
+
+arch_initcall(mpc8272ads_init);
diff --git a/arch/ppc/platforms/mpc866ads_setup.c b/arch/ppc/platforms/mpc866ads_setup.c
new file mode 100644
index 0000000..26b989f
--- /dev/null
+++ b/arch/ppc/platforms/mpc866ads_setup.c
@@ -0,0 +1,270 @@
+/*arch/ppc/platforms/mpc885ads-setup.c
+ *
+ * Platform setup for the Freescale mpc885ads board
+ *
+ * Vitaly Bordug <vbordug@ru.mvista.com>
+ *
+ * Copyright 2005 MontaVista Software Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/param.h>
+#include <linux/string.h>
+#include <linux/ioport.h>
+#include <linux/device.h>
+
+#include <linux/fs_enet_pd.h>
+#include <linux/mii.h>
+
+#include <asm/delay.h>
+#include <asm/io.h>
+#include <asm/machdep.h>
+#include <asm/page.h>
+#include <asm/processor.h>
+#include <asm/system.h>
+#include <asm/time.h>
+#include <asm/ppcboot.h>
+#include <asm/8xx_immap.h>
+#include <asm/commproc.h>
+#include <asm/ppc_sys.h>
+#include <asm/mpc8xx.h>
+
+extern unsigned char __res[];
+
+static struct fs_mii_bus_info fec_mii_bus_info = {
+ .method = fsmii_fec,
+ .id = 0,
+};
+
+static struct fs_mii_bus_info scc_mii_bus_info = {
+ .method = fsmii_fixed,
+ .id = 0,
+ .i.fixed.speed = 10,
+ .i.fixed.duplex = 0,
+};
+
+static struct fs_platform_info mpc8xx_fec_pdata[] = {
+ {
+ .rx_ring = 128,
+ .tx_ring = 16,
+ .rx_copybreak = 240,
+
+ .use_napi = 1,
+ .napi_weight = 17,
+
+ .phy_addr = 15,
+ .phy_irq = -1,
+
+ .use_rmii = 0,
+
+ .bus_info = &fec_mii_bus_info,
+ }
+};
+
+static struct fs_platform_info mpc8xx_scc_pdata = {
+ .rx_ring = 64,
+ .tx_ring = 8,
+ .rx_copybreak = 240,
+
+ .use_napi = 1,
+ .napi_weight = 17,
+
+ .phy_addr = -1,
+ .phy_irq = -1,
+
+ .bus_info = &scc_mii_bus_info,
+};
+
+void __init board_init(void)
+{
+ volatile cpm8xx_t *cp = cpmp;
+ unsigned *bcsr_io;
+
+ bcsr_io = ioremap(BCSR1, sizeof(unsigned long));
+
+ if (bcsr_io == NULL) {
+ printk(KERN_CRIT "Could not remap BCSR1\n");
+ return;
+ }
+#ifdef CONFIG_SERIAL_CPM_SMC1
+ cp->cp_simode &= ~(0xe0000000 >> 17); /* brg1 */
+ clrbits32(bcsr_io,(0x80000000 >> 7));
+#else
+ setbits32(bcsr_io,(0x80000000 >> 7));
+
+ cp->cp_pbpar &= ~(0x000000c0);
+ cp->cp_pbdir |= 0x000000c0;
+ cp->cp_smc[0].smc_smcmr = 0;
+ cp->cp_smc[0].smc_smce = 0;
+#endif
+
+#ifdef CONFIG_SERIAL_CPM_SMC2
+ cp->cp_simode &= ~(0xe0000000 >> 1);
+ cp->cp_simode |= (0x20000000 >> 1); /* brg2 */
+ clrbits32(bcsr_io,(0x80000000 >> 13));
+#else
+ clrbits32(bcsr_io,(0x80000000 >> 13));
+ cp->cp_pbpar &= ~(0x00000c00);
+ cp->cp_pbdir |= 0x00000c00;
+ cp->cp_smc[1].smc_smcmr = 0;
+ cp->cp_smc[1].smc_smce = 0;
+#endif
+ iounmap(bcsr_io);
+}
+
+static void setup_fec1_ioports(void)
+{
+ immap_t *immap = (immap_t *) IMAP_ADDR;
+
+ setbits16(&immap->im_ioport.iop_pdpar, 0x1fff);
+ setbits16(&immap->im_ioport.iop_pddir, 0x1fff);
+}
+
+static void setup_scc1_ioports(void)
+{
+ immap_t *immap = (immap_t *) IMAP_ADDR;
+ unsigned *bcsr_io;
+
+ bcsr_io = ioremap(BCSR1, sizeof(unsigned long));
+
+ if (bcsr_io == NULL) {
+ printk(KERN_CRIT "Could not remap BCSR1\n");
+ return;
+ }
+
+ /* Enable the PHY.
+ */
+ clrbits32(bcsr_io,BCSR1_ETHEN);
+
+ /* Configure port A pins for Txd and Rxd.
+ */
+ /* Disable receive and transmit in case EPPC-Bug started it.
+ */
+ setbits16(&immap->im_ioport.iop_papar, PA_ENET_RXD | PA_ENET_TXD);
+ clrbits16(&immap->im_ioport.iop_padir, PA_ENET_RXD | PA_ENET_TXD);
+ clrbits16(&immap->im_ioport.iop_paodr, PA_ENET_TXD);
+
+ /* Configure port C pins to enable CLSN and RENA.
+ */
+ clrbits16(&immap->im_ioport.iop_pcpar, PC_ENET_CLSN | PC_ENET_RENA);
+ clrbits16(&immap->im_ioport.iop_pcdir, PC_ENET_CLSN | PC_ENET_RENA);
+ setbits16(&immap->im_ioport.iop_pcso, PC_ENET_CLSN | PC_ENET_RENA);
+ /* Configure port A for TCLK and RCLK.
+ */
+ setbits16(&immap->im_ioport.iop_papar, PA_ENET_TCLK | PA_ENET_RCLK);
+ clrbits16(&immap->im_ioport.iop_padir, PA_ENET_TCLK | PA_ENET_RCLK);
+ clrbits32(&immap->im_cpm.cp_pbpar, PB_ENET_TENA);
+ clrbits32(&immap->im_cpm.cp_pbdir, PB_ENET_TENA);
+
+ /* Configure Serial Interface clock routing.
+ * First, clear all SCC bits to zero, then set the ones we want.
+ */
+ clrbits32(&immap->im_cpm.cp_sicr, SICR_ENET_MASK);
+ setbits32(&immap->im_cpm.cp_sicr, SICR_ENET_CLKRT);
+
+ /* In the original SCC enet driver the following code is placed at
+ the end of the initialization */
+ setbits32(&immap->im_cpm.cp_pbpar, PB_ENET_TENA);
+ setbits32(&immap->im_cpm.cp_pbdir, PB_ENET_TENA);
+
+}
+
+static void mpc866ads_fixup_enet_pdata(struct platform_device *pdev, int fs_no)
+{
+ struct fs_platform_info *fpi = pdev->dev.platform_data;
+
+ volatile cpm8xx_t *cp;
+ bd_t *bd = (bd_t *) __res;
+ char *e;
+ int i;
+
+ /* Get pointer to Communication Processor */
+ cp = cpmp;
+ switch (fs_no) {
+ case fsid_fec1:
+ fpi = &mpc8xx_fec_pdata[0];
+ fpi->init_ioports = &setup_fec1_ioports;
+
+ break;
+ case fsid_scc1:
+ fpi = &mpc8xx_scc_pdata;
+ fpi->init_ioports = &setup_scc1_ioports;
+
+ break;
+ default:
+ break;
+ }
+
+ pdev->dev.platform_data = fpi;
+ fpi->fs_no = fs_no;
+
+ e = (unsigned char *)&bd->bi_enetaddr;
+ for (i = 0; i < 6; i++)
+ fpi->macaddr[i] = *e++;
+
+ fpi->macaddr[5 - pdev->id]++;
+
+}
+
+static void mpc866ads_fixup_fec_enet_pdata(struct platform_device *pdev,
+ int idx)
+{
+ /* This is for FEC devices only */
+ if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-fec")))
+ return;
+ mpc866ads_fixup_enet_pdata(pdev, fsid_fec1 + pdev->id - 1);
+}
+
+static void mpc866ads_fixup_scc_enet_pdata(struct platform_device *pdev,
+ int idx)
+{
+ /* This is for SCC devices only */
+ if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-scc")))
+ return;
+
+ mpc866ads_fixup_enet_pdata(pdev, fsid_scc1 + pdev->id - 1);
+}
+
+static int mpc866ads_platform_notify(struct device *dev)
+{
+ static const struct platform_notify_dev_map dev_map[] = {
+ {
+ .bus_id = "fsl-cpm-fec",
+ .rtn = mpc866ads_fixup_fec_enet_pdata,
+ },
+ {
+ .bus_id = "fsl-cpm-scc",
+ .rtn = mpc866ads_fixup_scc_enet_pdata,
+ },
+ {
+ .bus_id = NULL
+ }
+ };
+
+ platform_notify_map(dev_map,dev);
+
+ return 0;
+}
+
+int __init mpc866ads_init(void)
+{
+ printk(KERN_NOTICE "mpc866ads: Init\n");
+
+ platform_notify = mpc866ads_platform_notify;
+
+ ppc_sys_device_initfunc();
+#ifdef MPC8xx_SECOND_ETH_SCC1
+ ppc_sys_device_enable(MPC8xx_CPM_SCC1);
+#endif
+ ppc_sys_device_enable(MPC8xx_CPM_FEC1);
+
+ return 0;
+}
+
+arch_initcall(mpc866ads_init);
diff --git a/arch/ppc/platforms/mpc885ads_setup.c b/arch/ppc/platforms/mpc885ads_setup.c
new file mode 100644
index 0000000..816cade
--- /dev/null
+++ b/arch/ppc/platforms/mpc885ads_setup.c
@@ -0,0 +1,387 @@
+/*arch/ppc/platforms/mpc885ads-setup.c
+ *
+ * Platform setup for the Freescale mpc885ads board
+ *
+ * Vitaly Bordug <vbordug@ru.mvista.com>
+ *
+ * Copyright 2005 MontaVista Software Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/param.h>
+#include <linux/string.h>
+#include <linux/ioport.h>
+#include <linux/device.h>
+
+#include <linux/fs_enet_pd.h>
+#include <linux/mii.h>
+
+#include <asm/delay.h>
+#include <asm/io.h>
+#include <asm/machdep.h>
+#include <asm/page.h>
+#include <asm/processor.h>
+#include <asm/system.h>
+#include <asm/time.h>
+#include <asm/ppcboot.h>
+#include <asm/8xx_immap.h>
+#include <asm/commproc.h>
+#include <asm/ppc_sys.h>
+
+extern unsigned char __res[];
+
+static void __init mpc885ads_scc_phy_init(char);
+
+static struct fs_mii_bus_info fec_mii_bus_info = {
+ .method = fsmii_fec,
+ .id = 0,
+};
+
+static struct fs_mii_bus_info scc_mii_bus_info = {
+#ifdef CONFIG_SCC_ENET_8xx_FIXED
+ .method = fsmii_fixed,
+#else
+ .method = fsmii_fec,
+#endif
+
+ .id = 0,
+};
+
+static struct fs_platform_info mpc8xx_fec_pdata[] = {
+ {
+ .rx_ring = 128,
+ .tx_ring = 16,
+ .rx_copybreak = 240,
+
+ .use_napi = 1,
+ .napi_weight = 17,
+
+ .phy_addr = 0,
+ .phy_irq = SIU_IRQ7,
+
+ .bus_info = &fec_mii_bus_info,
+ }, {
+ .rx_ring = 128,
+ .tx_ring = 16,
+ .rx_copybreak = 240,
+
+ .use_napi = 1,
+ .napi_weight = 17,
+
+ .phy_addr = 1,
+ .phy_irq = SIU_IRQ7,
+
+ .bus_info = &fec_mii_bus_info,
+ }
+};
+
+static struct fs_platform_info mpc8xx_scc_pdata = {
+ .rx_ring = 64,
+ .tx_ring = 8,
+ .rx_copybreak = 240,
+
+ .use_napi = 1,
+ .napi_weight = 17,
+
+ .phy_addr = 2,
+#ifdef CONFIG_MPC8xx_SCC_ENET_FIXED
+ .phy_irq = -1,
+#else
+ .phy_irq = SIU_IRQ7,
+#endif
+
+ .bus_info = &scc_mii_bus_info,
+};
+
+void __init board_init(void)
+{
+ volatile cpm8xx_t *cp = cpmp;
+ unsigned int *bcsr_io;
+
+#ifdef CONFIG_FS_ENET
+ immap_t *immap = (immap_t *) IMAP_ADDR;
+#endif
+ bcsr_io = ioremap(BCSR1, sizeof(unsigned long));
+
+ if (bcsr_io == NULL) {
+ printk(KERN_CRIT "Could not remap BCSR\n");
+ return;
+ }
+#ifdef CONFIG_SERIAL_CPM_SMC1
+ cp->cp_simode &= ~(0xe0000000 >> 17); /* brg1 */
+ clrbits32(bcsr_io, BCSR1_RS232EN_1);
+#else
+ setbits32(bcsr_io,BCSR1_RS232EN_1);
+ cp->cp_smc[0].smc_smcmr = 0;
+ cp->cp_smc[0].smc_smce = 0;
+#endif
+
+#ifdef CONFIG_SERIAL_CPM_SMC2
+ cp->cp_simode &= ~(0xe0000000 >> 1);
+ cp->cp_simode |= (0x20000000 >> 1); /* brg2 */
+ clrbits32(bcsr_io,BCSR1_RS232EN_2);
+#else
+ setbits32(bcsr_io,BCSR1_RS232EN_2);
+ cp->cp_smc[1].smc_smcmr = 0;
+ cp->cp_smc[1].smc_smce = 0;
+#endif
+ iounmap(bcsr_io);
+
+#ifdef CONFIG_FS_ENET
+ /* use MDC for MII (common) */
+ setbits16(&immap->im_ioport.iop_pdpar, 0x0080);
+ clrbits16(&immap->im_ioport.iop_pddir, 0x0080);
+#endif
+}
+
+static void setup_fec1_ioports(void)
+{
+ immap_t *immap = (immap_t *) IMAP_ADDR;
+
+ /* configure FEC1 pins */
+ setbits16(&immap->im_ioport.iop_papar, 0xf830);
+ setbits16(&immap->im_ioport.iop_padir, 0x0830);
+ clrbits16(&immap->im_ioport.iop_padir, 0xf000);
+ setbits32(&immap->im_cpm.cp_pbpar, 0x00001001);
+
+ clrbits32(&immap->im_cpm.cp_pbdir, 0x00001001);
+ setbits16(&immap->im_ioport.iop_pcpar, 0x000c);
+ clrbits16(&immap->im_ioport.iop_pcdir, 0x000c);
+ setbits32(&immap->im_cpm.cp_pepar, 0x00000003);
+
+ setbits32(&immap->im_cpm.cp_pedir, 0x00000003);
+ clrbits32(&immap->im_cpm.cp_peso, 0x00000003);
+ clrbits32(&immap->im_cpm.cp_cptr, 0x00000100);
+}
+
+static void setup_fec2_ioports(void)
+{
+ immap_t *immap = (immap_t *) IMAP_ADDR;
+
+ /* configure FEC2 pins */
+ setbits32(&immap->im_cpm.cp_pepar, 0x0003fffc);
+ setbits32(&immap->im_cpm.cp_pedir, 0x0003fffc);
+ setbits32(&immap->im_cpm.cp_peso, 0x00037800);
+ clrbits32(&immap->im_cpm.cp_peso, 0x000087fc);
+ clrbits32(&immap->im_cpm.cp_cptr, 0x00000080);
+}
+
+static void setup_scc3_ioports(void)
+{
+ immap_t *immap = (immap_t *) IMAP_ADDR;
+ unsigned *bcsr_io;
+
+ bcsr_io = ioremap(BCSR_ADDR, BCSR_SIZE);
+
+ if (bcsr_io == NULL) {
+ printk(KERN_CRIT "Could not remap BCSR\n");
+ return;
+ }
+
+ /* Enable the PHY.
+ */
+ setbits32(bcsr_io+4, BCSR4_ETH10_RST);
+ /* Configure port A pins for Txd and Rxd.
+ */
+ setbits16(&immap->im_ioport.iop_papar, PA_ENET_RXD | PA_ENET_TXD);
+ clrbits16(&immap->im_ioport.iop_padir, PA_ENET_RXD | PA_ENET_TXD);
+
+ /* Configure port C pins to enable CLSN and RENA.
+ */
+ clrbits16(&immap->im_ioport.iop_pcpar, PC_ENET_CLSN | PC_ENET_RENA);
+ clrbits16(&immap->im_ioport.iop_pcdir, PC_ENET_CLSN | PC_ENET_RENA);
+ setbits16(&immap->im_ioport.iop_pcso, PC_ENET_CLSN | PC_ENET_RENA);
+
+ /* Configure port E for TCLK and RCLK.
+ */
+ setbits32(&immap->im_cpm.cp_pepar, PE_ENET_TCLK | PE_ENET_RCLK);
+ clrbits32(&immap->im_cpm.cp_pepar, PE_ENET_TENA);
+ clrbits32(&immap->im_cpm.cp_pedir,
+ PE_ENET_TCLK | PE_ENET_RCLK | PE_ENET_TENA);
+ clrbits32(&immap->im_cpm.cp_peso, PE_ENET_TCLK | PE_ENET_RCLK);
+ setbits32(&immap->im_cpm.cp_peso, PE_ENET_TENA);
+
+ /* Configure Serial Interface clock routing.
+ * First, clear all SCC bits to zero, then set the ones we want.
+ */
+ clrbits32(&immap->im_cpm.cp_sicr, SICR_ENET_MASK);
+ setbits32(&immap->im_cpm.cp_sicr, SICR_ENET_CLKRT);
+
+ /* Disable Rx and Tx. SMC1 sshould be stopped if SCC3 eternet are used.
+ */
+ immap->im_cpm.cp_smc[0].smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
+ /* On the MPC885ADS SCC ethernet PHY is initialized in the full duplex mode
+ * by H/W setting after reset. SCC ethernet controller support only half duplex.
+ * This discrepancy of modes causes a lot of carrier lost errors.
+ */
+
+ /* In the original SCC enet driver the following code is placed at
+ the end of the initialization */
+ setbits32(&immap->im_cpm.cp_pepar, PE_ENET_TENA);
+ clrbits32(&immap->im_cpm.cp_pedir, PE_ENET_TENA);
+ setbits32(&immap->im_cpm.cp_peso, PE_ENET_TENA);
+
+ setbits32(bcsr_io+1, BCSR1_ETHEN);
+ iounmap(bcsr_io);
+}
+
+static void mpc885ads_fixup_enet_pdata(struct platform_device *pdev, int fs_no)
+{
+ struct fs_platform_info *fpi = pdev->dev.platform_data;
+
+ volatile cpm8xx_t *cp;
+ bd_t *bd = (bd_t *) __res;
+ char *e;
+ int i;
+
+ /* Get pointer to Communication Processor */
+ cp = cpmp;
+ switch (fs_no) {
+ case fsid_fec1:
+ fpi = &mpc8xx_fec_pdata[0];
+ fpi->init_ioports = &setup_fec1_ioports;
+ break;
+ case fsid_fec2:
+ fpi = &mpc8xx_fec_pdata[1];
+ fpi->init_ioports = &setup_fec2_ioports;
+ break;
+ case fsid_scc3:
+ fpi = &mpc8xx_scc_pdata;
+ fpi->init_ioports = &setup_scc3_ioports;
+ mpc885ads_scc_phy_init(fpi->phy_addr);
+ break;
+ default:
+ break;
+ }
+
+ pdev->dev.platform_data = fpi;
+ fpi->fs_no = fs_no;
+
+ e = (unsigned char *)&bd->bi_enetaddr;
+ for (i = 0; i < 6; i++)
+ fpi->macaddr[i] = *e++;
+
+ fpi->macaddr[5 - pdev->id]++;
+
+}
+
+static void mpc885ads_fixup_fec_enet_pdata(struct platform_device *pdev,
+ int idx)
+{
+ /* This is for FEC devices only */
+ if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-fec")))
+ return;
+ mpc885ads_fixup_enet_pdata(pdev, fsid_fec1 + pdev->id - 1);
+}
+
+static void __init mpc885ads_fixup_scc_enet_pdata(struct platform_device *pdev,
+ int idx)
+{
+ /* This is for SCC devices only */
+ if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-scc")))
+ return;
+
+ mpc885ads_fixup_enet_pdata(pdev, fsid_scc1 + pdev->id - 1);
+}
+
+/* SCC ethernet controller does not have MII management channel. FEC1 MII
+ * channel is used to communicate with the 10Mbit PHY.
+ */
+
+#define MII_ECNTRL_PINMUX 0x4
+#define FEC_ECNTRL_PINMUX 0x00000004
+#define FEC_RCNTRL_MII_MODE 0x00000004
+
+/* Make MII read/write commands.
+ */
+#define mk_mii_write(REG, VAL, PHY_ADDR) (0x50020000 | (((REG) & 0x1f) << 18) | \
+ ((VAL) & 0xffff) | ((PHY_ADDR) << 23))
+
+static void mpc885ads_scc_phy_init(char phy_addr)
+{
+ volatile immap_t *immap;
+ volatile fec_t *fecp;
+ bd_t *bd;
+
+ bd = (bd_t *) __res;
+ immap = (immap_t *) IMAP_ADDR; /* pointer to internal registers */
+ fecp = &(immap->im_cpm.cp_fec);
+
+ /* Enable MII pins of the FEC1
+ */
+ setbits16(&immap->im_ioport.iop_pdpar, 0x0080);
+ clrbits16(&immap->im_ioport.iop_pddir, 0x0080);
+ /* Set MII speed to 2.5 MHz
+ */
+ out_be32(&fecp->fec_mii_speed,
+ ((((bd->bi_intfreq + 4999999) / 2500000) / 2) & 0x3F) << 1);
+
+ /* Enable FEC pin MUX
+ */
+ setbits32(&fecp->fec_ecntrl, MII_ECNTRL_PINMUX);
+ setbits32(&fecp->fec_r_cntrl, FEC_RCNTRL_MII_MODE);
+
+ out_be32(&fecp->fec_mii_data,
+ mk_mii_write(MII_BMCR, BMCR_ISOLATE, phy_addr));
+ udelay(100);
+ out_be32(&fecp->fec_mii_data,
+ mk_mii_write(MII_ADVERTISE,
+ ADVERTISE_10HALF | ADVERTISE_CSMA, phy_addr));
+ udelay(100);
+
+ /* Disable FEC MII settings
+ */
+ clrbits32(&fecp->fec_ecntrl, MII_ECNTRL_PINMUX);
+ clrbits32(&fecp->fec_r_cntrl, FEC_RCNTRL_MII_MODE);
+ out_be32(&fecp->fec_mii_speed, 0);
+}
+
+static int mpc885ads_platform_notify(struct device *dev)
+{
+
+ static const struct platform_notify_dev_map dev_map[] = {
+ {
+ .bus_id = "fsl-cpm-fec",
+ .rtn = mpc885ads_fixup_fec_enet_pdata,
+ },
+ {
+ .bus_id = "fsl-cpm-scc",
+ .rtn = mpc885ads_fixup_scc_enet_pdata,
+ },
+ {
+ .bus_id = NULL
+ }
+ };
+
+ platform_notify_map(dev_map,dev);
+
+}
+
+int __init mpc885ads_init(void)
+{
+ printk(KERN_NOTICE "mpc885ads: Init\n");
+
+ platform_notify = mpc885ads_platform_notify;
+
+ ppc_sys_device_initfunc();
+
+ ppc_sys_device_enable(MPC8xx_CPM_FEC1);
+
+#ifdef CONFIG_MPC8xx_SECOND_ETH_SCC3
+ ppc_sys_device_enable(MPC8xx_CPM_SCC1);
+
+#endif
+#ifdef CONFIG_MPC8xx_SECOND_ETH_FEC2
+ ppc_sys_device_enable(MPC8xx_CPM_FEC2);
+#endif
+
+ return 0;
+}
+
+arch_initcall(mpc885ads_init);
diff --git a/arch/ppc/platforms/pq2ads.h b/arch/ppc/platforms/pq2ads.h
index 067d9a5..6b26dd3 100644
--- a/arch/ppc/platforms/pq2ads.h
+++ b/arch/ppc/platforms/pq2ads.h
@@ -13,6 +13,10 @@
#include <asm/ppcboot.h>
+#if defined(CONFIG_ADS8272)
+#define BOARD_CHIP_NAME "8272"
+#endif
+
/* Memory map is configured by the PROM startup.
* We just map a few things we need. The CSR is actually 4 byte-wide
* registers that can be accessed as 8-, 16-, or 32-bit values.
diff --git a/arch/ppc/platforms/pq2ads_pd.h b/arch/ppc/platforms/pq2ads_pd.h
new file mode 100644
index 0000000..8f14a43
--- /dev/null
+++ b/arch/ppc/platforms/pq2ads_pd.h
@@ -0,0 +1,114 @@
+#ifndef __PQ2ADS_PD_H
+#define __PQ2ADS_PD_H
+/*
+ * arch/ppc/platforms/82xx/pq2ads_pd.h
+ *
+ * Some defines for MPC82xx board-specific PlatformDevice descriptions
+ *
+ * 2005 (c) MontaVista Software, Inc.
+ * Vitaly Bordug <vbordug@ru.mvista.com>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/* FCC1 Clock Source Configuration. These can be redefined in the board specific file.
+ Can only choose from CLK9-12 */
+
+#define F1_RXCLK 11
+#define F1_TXCLK 10
+
+/* FCC2 Clock Source Configuration. These can be redefined in the board specific file.
+ Can only choose from CLK13-16 */
+#define F2_RXCLK 15
+#define F2_TXCLK 16
+
+/* FCC3 Clock Source Configuration. These can be redefined in the board specific file.
+ Can only choose from CLK13-16 */
+#define F3_RXCLK 13
+#define F3_TXCLK 14
+
+/* Automatically generates register configurations */
+#define PC_CLK(x) ((uint)(1<<(x-1))) /* FCC CLK I/O ports */
+
+#define CMXFCR_RF1CS(x) ((uint)((x-5)<<27)) /* FCC1 Receive Clock Source */
+#define CMXFCR_TF1CS(x) ((uint)((x-5)<<24)) /* FCC1 Transmit Clock Source */
+#define CMXFCR_RF2CS(x) ((uint)((x-9)<<19)) /* FCC2 Receive Clock Source */
+#define CMXFCR_TF2CS(x) ((uint)((x-9)<<16)) /* FCC2 Transmit Clock Source */
+#define CMXFCR_RF3CS(x) ((uint)((x-9)<<11)) /* FCC3 Receive Clock Source */
+#define CMXFCR_TF3CS(x) ((uint)((x-9)<<8)) /* FCC3 Transmit Clock Source */
+
+#define PC_F1RXCLK PC_CLK(F1_RXCLK)
+#define PC_F1TXCLK PC_CLK(F1_TXCLK)
+#define CMX1_CLK_ROUTE (CMXFCR_RF1CS(F1_RXCLK) | CMXFCR_TF1CS(F1_TXCLK))
+#define CMX1_CLK_MASK ((uint)0xff000000)
+
+#define PC_F2RXCLK PC_CLK(F2_RXCLK)
+#define PC_F2TXCLK PC_CLK(F2_TXCLK)
+#define CMX2_CLK_ROUTE (CMXFCR_RF2CS(F2_RXCLK) | CMXFCR_TF2CS(F2_TXCLK))
+#define CMX2_CLK_MASK ((uint)0x00ff0000)
+
+#define PC_F3RXCLK PC_CLK(F3_RXCLK)
+#define PC_F3TXCLK PC_CLK(F3_TXCLK)
+#define CMX3_CLK_ROUTE (CMXFCR_RF3CS(F3_RXCLK) | CMXFCR_TF3CS(F3_TXCLK))
+#define CMX3_CLK_MASK ((uint)0x0000ff00)
+
+/* I/O Pin assignment for FCC1. I don't yet know the best way to do this,
+ * but there is little variation among the choices.
+ */
+#define PA1_COL 0x00000001U
+#define PA1_CRS 0x00000002U
+#define PA1_TXER 0x00000004U
+#define PA1_TXEN 0x00000008U
+#define PA1_RXDV 0x00000010U
+#define PA1_RXER 0x00000020U
+#define PA1_TXDAT 0x00003c00U
+#define PA1_RXDAT 0x0003c000U
+#define PA1_PSORA0 (PA1_RXDAT | PA1_TXDAT)
+#define PA1_PSORA1 (PA1_COL | PA1_CRS | PA1_TXER | PA1_TXEN | \
+ PA1_RXDV | PA1_RXER)
+#define PA1_DIRA0 (PA1_RXDAT | PA1_CRS | PA1_COL | PA1_RXER | PA1_RXDV)
+#define PA1_DIRA1 (PA1_TXDAT | PA1_TXEN | PA1_TXER)
+
+
+/* I/O Pin assignment for FCC2. I don't yet know the best way to do this,
+ * but there is little variation among the choices.
+ */
+#define PB2_TXER 0x00000001U
+#define PB2_RXDV 0x00000002U
+#define PB2_TXEN 0x00000004U
+#define PB2_RXER 0x00000008U
+#define PB2_COL 0x00000010U
+#define PB2_CRS 0x00000020U
+#define PB2_TXDAT 0x000003c0U
+#define PB2_RXDAT 0x00003c00U
+#define PB2_PSORB0 (PB2_RXDAT | PB2_TXDAT | PB2_CRS | PB2_COL | \
+ PB2_RXER | PB2_RXDV | PB2_TXER)
+#define PB2_PSORB1 (PB2_TXEN)
+#define PB2_DIRB0 (PB2_RXDAT | PB2_CRS | PB2_COL | PB2_RXER | PB2_RXDV)
+#define PB2_DIRB1 (PB2_TXDAT | PB2_TXEN | PB2_TXER)
+
+
+/* I/O Pin assignment for FCC3. I don't yet know the best way to do this,
+ * but there is little variation among the choices.
+ */
+#define PB3_RXDV 0x00004000U
+#define PB3_RXER 0x00008000U
+#define PB3_TXER 0x00010000U
+#define PB3_TXEN 0x00020000U
+#define PB3_COL 0x00040000U
+#define PB3_CRS 0x00080000U
+#define PB3_TXDAT 0x0f000000U
+#define PB3_RXDAT 0x00f00000U
+#define PB3_PSORB0 (PB3_RXDAT | PB3_TXDAT | PB3_CRS | PB3_COL | \
+ PB3_RXER | PB3_RXDV | PB3_TXER | PB3_TXEN)
+#define PB3_PSORB1 0
+#define PB3_DIRB0 (PB3_RXDAT | PB3_CRS | PB3_COL | PB3_RXER | PB3_RXDV)
+#define PB3_DIRB1 (PB3_TXDAT | PB3_TXEN | PB3_TXER)
+
+#define FCC_MEM_OFFSET(x) (CPM_FCC_SPECIAL_BASE + (x*128))
+#define FCC1_MEM_OFFSET FCC_MEM_OFFSET(0)
+#define FCC2_MEM_OFFSET FCC_MEM_OFFSET(1)
+
+#endif
diff --git a/arch/ppc/syslib/ppc_sys.c b/arch/ppc/syslib/ppc_sys.c
index e3856e7..9182a36 100644
--- a/arch/ppc/syslib/ppc_sys.c
+++ b/arch/ppc/syslib/ppc_sys.c
@@ -238,7 +238,7 @@ void ppc_sys_device_setfunc(enum ppc_sys
else
*s = 0;
} else if (func != PPC_SYS_FUNC_DUMMY) {
- /* do assignment if it is not just "enable" request */
+ /* do assignment if it is not just "clear" request */
sprintf(tmp, "%s:%s", name, ppc_sys_func_names[func]);
strlcpy(name, tmp, BUS_ID_SIZE);
}
@@ -294,7 +294,7 @@ static int __init ppc_sys_init(void)
for (i = 0; i < cur_ppc_sys_spec->num_devices; i++) {
dev_id = cur_ppc_sys_spec->device_list[i];
- if ((dev_id != -1) ||
+ if ((dev_id != -1) &&
(cur_ppc_sys_spec->config[dev_id] & PPC_SYS_CONFIG_ENABED)) {
if (ppc_sys_device_fixup != NULL)
ppc_sys_device_fixup(&ppc_sys_platform_devices
diff --git a/drivers/base/platform.c b/drivers/base/platform.c
index 8827daf..ce551b5 100644
--- a/drivers/base/platform.c
+++ b/drivers/base/platform.c
@@ -266,7 +266,7 @@ int platform_device_add(struct platform_
}
}
- pr_debug("Registering platform device '%s'. Parent at %s\n",
+ pr_info("Registering platform device '%s'. Parent at %s\n",
pdev->dev.bus_id, pdev->dev.parent->bus_id);
ret = device_register(&pdev->dev);
^ permalink raw reply related
* [PATCH 1/2] ppc32: Make platform devices being able to assign functions
From: Vitaly Bordug @ 2005-12-28 19:21 UTC (permalink / raw)
To: Kumar Gala; +Cc: linuxppc-embedded list
Implemented by modification of the .name field of the platform device,
when PDs with the
same names are to be used within different drivers, as
<device_name> -> <device_name>:<function>
Corresponding drivers should change the .name in struct device_driver to
reflect upper of course.
Also helper platform_notify_map function added, making assignment of
board-specific platform_info more consistent and generic.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
---
arch/ppc/syslib/ppc_sys.c | 165 ++++++++++++++++++++++++++++++++++++++++++++-
include/asm-ppc/mpc10x.h | 1
include/asm-ppc/mpc52xx.h | 1
include/asm-ppc/mpc8260.h | 1
include/asm-ppc/mpc83xx.h | 1
include/asm-ppc/mpc85xx.h | 1
include/asm-ppc/mpc8xx.h | 1
include/asm-ppc/ppc_sys.h | 26 +++++++
8 files changed, 194 insertions(+), 3 deletions(-)
diff --git a/arch/ppc/syslib/ppc_sys.c b/arch/ppc/syslib/ppc_sys.c
index c0b93c4..e3856e7 100644
--- a/arch/ppc/syslib/ppc_sys.c
+++ b/arch/ppc/syslib/ppc_sys.c
@@ -15,11 +15,22 @@
*/
#include <linux/string.h>
+#include <linux/bootmem.h>
#include <asm/ppc_sys.h>
int (*ppc_sys_device_fixup) (struct platform_device * pdev);
static int ppc_sys_inited;
+static int ppc_sys_func_inited;
+
+static const char *ppc_sys_func_names[] = {
+ [PPC_SYS_FUNC_DUMMY] = "dummy",
+ [PPC_SYS_FUNC_ETH] = "eth",
+ [PPC_SYS_FUNC_UART] = "uart",
+ [PPC_SYS_FUNC_HLDC] = "hldc",
+ [PPC_SYS_FUNC_USB] = "usb",
+ [PPC_SYS_FUNC_IRDA] = "irda",
+};
void __init identify_ppc_sys_by_id(u32 id)
{
@@ -38,13 +49,13 @@ void __init identify_ppc_sys_by_id(u32 i
void __init identify_ppc_sys_by_name(char *name)
{
unsigned int i = 0;
- while (ppc_sys_specs[i].ppc_sys_name[0])
- {
+ while (ppc_sys_specs[i].ppc_sys_name[0]) {
if (!strcmp(ppc_sys_specs[i].ppc_sys_name, name))
break;
i++;
}
cur_ppc_sys_spec = &ppc_sys_specs[i];
+
return;
}
@@ -128,6 +139,153 @@ void ppc_sys_device_remove(enum ppc_sys_
}
}
+/* Platform-notify mapping
+ * Helper function for BSP code to assign board-specific platfom-divice bits
+ */
+
+void platform_notify_map(const struct platform_notify_dev_map *map,
+ struct device *dev)
+{
+ struct platform_device *pdev;
+ int len, idx;
+ const char *s;
+
+ /* do nothing if no device or no bus_id */
+ if (!dev || !dev->bus_id)
+ return;
+
+ /* call per device map */
+ while (map->bus_id != NULL) {
+ idx = -1;
+ s = strrchr(dev->bus_id, '.');
+ if (s != NULL)
+ idx = (int)simple_strtol(s + 1, NULL, 10);
+ else
+ s = dev->bus_id;
+
+ len = s - dev->bus_id;
+
+ if (!strncmp(dev->bus_id, map->bus_id, len)) {
+ pdev = container_of(dev, struct platform_device, dev);
+ map->rtn(pdev, idx);
+ }
+ map++;
+ }
+}
+
+/*
+ Function assignment stuff.
+ Intended to work as follows:
+ the device name defined in foo_devices.c will be concatenated with :"func",
+ where func is string map of respective function from platfom_device_func enum
+
+ The PPC_SYS_FUNC_DUMMY function is intended to remove all assignments, making the device to appear
+ in platform bus with unmodified name.
+ */
+
+/*
+ Here we'll replace .name pointers with fixed-lenght strings
+ Hereby, this should be called *before* any func stuff triggeded.
+ */
+void ppc_sys_device_initfunc(void)
+{
+ int i;
+ const char *name;
+ static char new_names[NUM_PPC_SYS_DEVS][BUS_ID_SIZE];
+ enum ppc_sys_devices cur_dev;
+
+ /* If inited yet, do nothing */
+ if (ppc_sys_func_inited)
+ return;
+
+ for (i = 0; i < cur_ppc_sys_spec->num_devices; i++) {
+ if ((cur_dev = cur_ppc_sys_spec->device_list[i]) < 0)
+ continue;
+
+ if (ppc_sys_platform_devices[cur_dev].name) {
+ /*backup name */
+ name = ppc_sys_platform_devices[cur_dev].name;
+ strlcpy(new_names[i], name, BUS_ID_SIZE);
+ ppc_sys_platform_devices[cur_dev].name = new_names[i];
+ }
+ }
+
+ ppc_sys_func_inited = 1;
+}
+
+/*The "engine" of the func stuff. Here we either concat specified function string description
+ to the name, or remove it if PPC_SYS_FUNC_DUMMY parameter is passed here*/
+void ppc_sys_device_setfunc(enum ppc_sys_devices dev,
+ enum platform_device_func func)
+{
+ char *s;
+ char *name = (char *)ppc_sys_platform_devices[dev].name;
+ char tmp[BUS_ID_SIZE];
+
+ if (!ppc_sys_func_inited) {
+ printk(KERN_ERR "Unable to alter function - not inited!\n");
+ return;
+ }
+
+ if (ppc_sys_inited) {
+ platform_device_unregister(&ppc_sys_platform_devices[dev]);
+ }
+
+ if ((s = (char *)strchr(name, ':')) != NULL) { /* reassign */
+ /* Either change the name after ':' or remove func modifications */
+ if (func != PPC_SYS_FUNC_DUMMY)
+ strlcpy(s + 1, ppc_sys_func_names[func], BUS_ID_SIZE);
+ else
+ *s = 0;
+ } else if (func != PPC_SYS_FUNC_DUMMY) {
+ /* do assignment if it is not just "enable" request */
+ sprintf(tmp, "%s:%s", name, ppc_sys_func_names[func]);
+ strlcpy(name, tmp, BUS_ID_SIZE);
+ }
+
+ if (ppc_sys_inited) {
+ platform_device_register(&ppc_sys_platform_devices[dev]);
+ }
+}
+
+void ppc_sys_device_disable(enum ppc_sys_devices dev)
+{
+ BUG_ON(cur_ppc_sys_spec == NULL);
+
+ /*Check if it is enabled*/
+ if(cur_ppc_sys_spec->config[dev] & PPC_SYS_CONFIG_ENABED) {
+ if (ppc_sys_inited) {
+ platform_device_unregister(&ppc_sys_platform_devices[dev]);
+ }
+ cur_ppc_sys_spec->config[dev] &= ~PPC_SYS_CONFIG_ENABED;
+ }
+}
+
+void ppc_sys_device_enable(enum ppc_sys_devices dev)
+{
+ BUG_ON(cur_ppc_sys_spec == NULL);
+
+ /*Check if it is disabled*/
+ if(!(cur_ppc_sys_spec->config[dev] & PPC_SYS_CONFIG_ENABED)) {
+ if (ppc_sys_inited) {
+ platform_device_register(&ppc_sys_platform_devices[dev]);
+ }
+ cur_ppc_sys_spec->config[dev] |= PPC_SYS_CONFIG_ENABED;
+ }
+
+}
+
+void ppc_sys_device_enable_all(enum platform_device_func func)
+{
+ enum ppc_sys_devices cur_dev;
+ int i;
+
+ for (i = 0; i < cur_ppc_sys_spec->num_devices; i++) {
+ cur_dev = cur_ppc_sys_spec->device_list[i];
+ ppc_sys_device_enable(cur_dev);
+ }
+}
+
static int __init ppc_sys_init(void)
{
unsigned int i, dev_id, ret = 0;
@@ -136,7 +294,8 @@ static int __init ppc_sys_init(void)
for (i = 0; i < cur_ppc_sys_spec->num_devices; i++) {
dev_id = cur_ppc_sys_spec->device_list[i];
- if (dev_id != -1) {
+ if ((dev_id != -1) ||
+ (cur_ppc_sys_spec->config[dev_id] & PPC_SYS_CONFIG_ENABED)) {
if (ppc_sys_device_fixup != NULL)
ppc_sys_device_fixup(&ppc_sys_platform_devices
[dev_id]);
diff --git a/include/asm-ppc/mpc10x.h b/include/asm-ppc/mpc10x.h
index 77b1e09..976ad3d 100644
--- a/include/asm-ppc/mpc10x.h
+++ b/include/asm-ppc/mpc10x.h
@@ -165,6 +165,7 @@ enum ppc_sys_devices {
MPC10X_DMA1,
MPC10X_UART0,
MPC10X_UART1,
+ NUM_PPC_SYS_DEVS,
};
int mpc10x_bridge_init(struct pci_controller *hose,
diff --git a/include/asm-ppc/mpc52xx.h b/include/asm-ppc/mpc52xx.h
index e5f80c2..b2cb44f 100644
--- a/include/asm-ppc/mpc52xx.h
+++ b/include/asm-ppc/mpc52xx.h
@@ -49,6 +49,7 @@ enum ppc_sys_devices {
MPC52xx_ATA,
MPC52xx_I2C1,
MPC52xx_I2C2,
+ NUM_PPC_SYS_DEVS,
};
diff --git a/include/asm-ppc/mpc8260.h b/include/asm-ppc/mpc8260.h
index 3214526..6ba69a8 100644
--- a/include/asm-ppc/mpc8260.h
+++ b/include/asm-ppc/mpc8260.h
@@ -83,6 +83,7 @@ enum ppc_sys_devices {
MPC82xx_CPM_SMC2,
MPC82xx_CPM_USB,
MPC82xx_SEC1,
+ NUM_PPC_SYS_DEVS,
};
#ifndef __ASSEMBLY__
diff --git a/include/asm-ppc/mpc83xx.h b/include/asm-ppc/mpc83xx.h
index 7cdf60f..3c23fc4 100644
--- a/include/asm-ppc/mpc83xx.h
+++ b/include/asm-ppc/mpc83xx.h
@@ -108,6 +108,7 @@ enum ppc_sys_devices {
MPC83xx_USB2_DR,
MPC83xx_USB2_MPH,
MPC83xx_MDIO,
+ NUM_PPC_SYS_DEVS,
};
#endif /* CONFIG_83xx */
diff --git a/include/asm-ppc/mpc85xx.h b/include/asm-ppc/mpc85xx.h
index 9d14bae..2a77884 100644
--- a/include/asm-ppc/mpc85xx.h
+++ b/include/asm-ppc/mpc85xx.h
@@ -135,6 +135,7 @@ enum ppc_sys_devices {
MPC85xx_eTSEC4,
MPC85xx_IIC2,
MPC85xx_MDIO,
+ NUM_PPC_SYS_DEVS,
};
/* Internal interrupts are all Level Sensitive, and Positive Polarity */
diff --git a/include/asm-ppc/mpc8xx.h b/include/asm-ppc/mpc8xx.h
index 46f159c..90e3d59 100644
--- a/include/asm-ppc/mpc8xx.h
+++ b/include/asm-ppc/mpc8xx.h
@@ -111,6 +111,7 @@ enum ppc_sys_devices {
MPC8xx_CPM_SMC1,
MPC8xx_CPM_SMC2,
MPC8xx_CPM_USB,
+ NUM_PPC_SYS_DEVS,
};
#ifndef BOARD_CHIP_NAME
diff --git a/include/asm-ppc/ppc_sys.h b/include/asm-ppc/ppc_sys.h
index 83d8c77..e6f83ad 100644
--- a/include/asm-ppc/ppc_sys.h
+++ b/include/asm-ppc/ppc_sys.h
@@ -44,9 +44,26 @@ struct ppc_sys_spec {
u32 value;
u32 num_devices;
char *ppc_sys_name;
+ u8 config[NUM_PPC_SYS_DEVS];
enum ppc_sys_devices *device_list;
};
+struct platform_notify_dev_map {
+ const char *bus_id;
+ void (*rtn)(struct platform_device * pdev, int idx);
+};
+
+enum platform_device_func {
+ PPC_SYS_FUNC_DUMMY = 0,
+ PPC_SYS_FUNC_ETH = 1,
+ PPC_SYS_FUNC_UART = 2,
+ PPC_SYS_FUNC_HLDC = 3,
+ PPC_SYS_FUNC_USB = 4,
+ PPC_SYS_FUNC_IRDA = 5,
+};
+
+#define PPC_SYS_CONFIG_ENABED 1
+
/* describes all specific chips and which devices they have on them */
extern struct ppc_sys_spec ppc_sys_specs[];
extern struct ppc_sys_spec *cur_ppc_sys_spec;
@@ -72,5 +89,14 @@ extern void *ppc_sys_get_pdata(enum ppc_
/* remove a device from the system */
extern void ppc_sys_device_remove(enum ppc_sys_devices dev);
+/*Function assignment stuff*/
+void ppc_sys_device_initfunc(void);
+void ppc_sys_device_setfunc(enum ppc_sys_devices dev,
+ enum platform_device_func func);
+void ppc_sys_device_set_func_all(enum platform_device_func func);
+
+void platform_notify_map(const struct platform_notify_dev_map *map,
+ struct device *dev);
+
#endif /* __ASM_PPC_SYS_H */
#endif /* __KERNEL__ */
^ permalink raw reply related
* Re: PReP fails to boot on QEMU (current git snapshot)
From: Grant Likely @ 2005-12-28 17:18 UTC (permalink / raw)
To: Paul Mackerras; +Cc: linuxppc-dev
In-Reply-To: <17330.32574.594398.522752@cargo.ozlabs.ibm.com>
Paul Mackerras wrote:
> Grant Likely writes:
>
>
>>zImage.prep built from head of Linus' tree fails to boot with the error
>>below.
>
>
> Did you do a parallel make (make -jN)? There is a problem currently
Nope, no flags to make whatsoever
g.
--
Grant Likely, B.Sc. P.Eng.
Secret Lab Technologies Ltd.
(403) 663-0761
^ permalink raw reply
* Re: ARCH=powerpc kexec seems to be broken ...
From: Sven Luther @ 2005-12-28 16:38 UTC (permalink / raw)
To: Sven Luther; +Cc: linuxppc-dev
In-Reply-To: <20051228104813.GA12862@localhost.localdomain>
On Wed, Dec 28, 2005 at 11:48:13AM +0100, Sven Luther wrote:
> Hi, ...
>
> I have for some time tried to build 2.6.15-rc debian kernels with
> ARCH=powerpc, and never quite succeeded. Thanks to Johannes Berg
> for helping investigating the issue.
>
> The problem seems to be that my .config enables KEXEC, and SWSUSP,
> which has nasty problems with ARCH=powerpc. In a 32bit config, i get :
>
> 00:03 < svenl> arch/ppc/kernel/built-in.o: In function `swsusp_arch_resume': multiple definition of `machine_shutdown'
> 00:03 < svenl> arch/powerpc/kernel/built-in.o: first defined here
>
> Which seems to indicate that machine_shutdown is built twice, once in the
> arch/ppc stuff and a second time in the arch/powerpc stuff.
>
> I have a similar problem for the 64bit case, but have not yet reached the
> point of the build where this happens, so i can't paste the error message
> here, but it was of the same kind as above if i remember well.
>
> Johannes said :
>
> 11:23 < johill> you enabled kexec, right?
> 11:24 < svenl> yeah, i did.
> 11:24 < svenl> is it broken for ARCH=powerpc right now ?
> 11:24 < johill> seems so
> 11:28 < johill> yeah. I don't think I can fix it, know too little about kexec
> 11:30 < johill> machine_shutdown should at least be moved from
> arch/ppc/kernel/machine_kexec.c to some file that is ARCH=ppc specific
> 11:31 < svenl> johill: as i understand this, i think it is already in some
> ARCH=ppc specific file, which is the cause of this trouble.
> 11:32 < johill> the way I interpret it is that the machine_kexec.c file is
> compiled for ARCH=powerpc too since it contains the 32bit specific
> implementation of kexec
> 11:32 < johill> but it contains a non-static machine_shutdown() function which
> ARCH=powerpc already moved to some non-32bit specific file
>
> So, it would be neat to either fix it, or at least mark the option as broken
> on 64bit powerpc, or something such.
And here is the 64bit error message :
__restore_cpu_setup': multiple definition of `machine_shutdown'
arch/powerpc/kernel/built-in.o: first defined here
I will disable KEXEC and see how it goes.
Friendly,
Sven Luther
^ permalink raw reply
* Re: ARCH=powerpc kexec seems to be broken ...
From: Sven Luther @ 2005-12-28 16:51 UTC (permalink / raw)
To: Sven Luther; +Cc: linuxppc-dev
In-Reply-To: <20051228163829.GA19292@localhost.localdomain>
On Wed, Dec 28, 2005 at 05:38:29PM +0100, Sven Luther wrote:
> On Wed, Dec 28, 2005 at 11:48:13AM +0100, Sven Luther wrote:
> > Hi, ...
> >
> > I have for some time tried to build 2.6.15-rc debian kernels with
> > ARCH=powerpc, and never quite succeeded. Thanks to Johannes Berg
> > for helping investigating the issue.
> >
> > The problem seems to be that my .config enables KEXEC, and SWSUSP,
> > which has nasty problems with ARCH=powerpc. In a 32bit config, i get :
> >
> > 00:03 < svenl> arch/ppc/kernel/built-in.o: In function `swsusp_arch_resume': multiple definition of `machine_shutdown'
> > 00:03 < svenl> arch/powerpc/kernel/built-in.o: first defined here
> >
> > Which seems to indicate that machine_shutdown is built twice, once in the
> > arch/ppc stuff and a second time in the arch/powerpc stuff.
> >
> > I have a similar problem for the 64bit case, but have not yet reached the
> > point of the build where this happens, so i can't paste the error message
> > here, but it was of the same kind as above if i remember well.
> >
> > Johannes said :
> >
> > 11:23 < johill> you enabled kexec, right?
> > 11:24 < svenl> yeah, i did.
> > 11:24 < svenl> is it broken for ARCH=powerpc right now ?
> > 11:24 < johill> seems so
> > 11:28 < johill> yeah. I don't think I can fix it, know too little about kexec
> > 11:30 < johill> machine_shutdown should at least be moved from
> > arch/ppc/kernel/machine_kexec.c to some file that is ARCH=ppc specific
> > 11:31 < svenl> johill: as i understand this, i think it is already in some
> > ARCH=ppc specific file, which is the cause of this trouble.
> > 11:32 < johill> the way I interpret it is that the machine_kexec.c file is
> > compiled for ARCH=powerpc too since it contains the 32bit specific
> > implementation of kexec
> > 11:32 < johill> but it contains a non-static machine_shutdown() function which
> > ARCH=powerpc already moved to some non-32bit specific file
> >
> > So, it would be neat to either fix it, or at least mark the option as broken
> > on 64bit powerpc, or something such.
>
> And here is the 64bit error message :
>
> __restore_cpu_setup': multiple definition of `machine_shutdown'
> arch/powerpc/kernel/built-in.o: first defined here
>
> I will disable KEXEC and see how it goes.
Oh well, sorry for the trouble, this seams due to having CONFIG_64bit set but
not CONFIG_PPC64, which is kind of not going to work.
Friendly,
Sven Luther
^ permalink raw reply
* XL C/C++ V7.0 Linux on POWER:Problem
From: Kriti Dutta @ 2005-12-28 14:56 UTC (permalink / raw)
To: linuxppc-dev
I encountered a compilation problem while building some C++ code that uses
the object space library (on Linux Power with
the gcc 3.3.3and xlC 7.0 compiler). This library defines its own STL's &
iostream implementation, and it seems that it
conflicts with the usage of the default standard iostream.The ERROR:
"/usr/include/g++/backward/iostream.h", line 35.1: 1540-0400 (S) "ostream"
has a conflicting declaration.
"/project/oracle/dc/src/dce/ol1/olstrm.h", line 83.7: 1540-0424 (I)
"ostream" is declared on line 83 of
"/project/oracle/dc/src/dce/ol1/olstrm.h".
"/project/oracle/dc/src/bin/ospace/Linux/ospace/std/iosfwd", line 24.10:
1540-0400 (S)
"class istream" has a conflicting declaration.
"/usr/include/g++/backward/iostream.h", line 36.1: 1540-0424 (I) "istream"
is declared on line 36 of
/usr/include/g++/backward/iostream.h".
"/project/oracle/dc/src/dce/ol1/ollogm.h", line 78.45: 1540-0063 (S)
The text "ostrstream" is unexpected.
"/project/oracle/dc/src/bin/ospace/Linux/ospace/osstd/list.h", line 572.7:
1540-0415 (S)
"template <class T, class Allocator> class list" is already declared with
default template arguments.
Are there any flags available to say the compiler that it should not use
the standard IO files.
N.B: The same code has been compiled with gcc-2.95 on Linux & xlC-6.0 on
AIX without any issues.
With regards
Kriti.
^ permalink raw reply
* Re: Which CAN driver to port to for PPC
From: Alessandro Rubini @ 2005-12-28 15:07 UTC (permalink / raw)
To: avolkov; +Cc: r.schwebel, david.jander, socket-can, linuxppc-embedded
In-Reply-To: <43B2A902.3090008@varma-el.com>
> Robert Schwebel et al have worked socket based CAN (i.e. implement CAN
> as _net_ dev, not as char)
That's great. I've always been convinced it is the right way to go.
I remember I've said so to a friend in March 2002. Unfortunately,
I had no time to do it the right way, due to short deadlines and
tight budget. I'm happy Robert did it.
/alessandro
^ permalink raw reply
* Re: Which CAN driver to port to for PPC
From: David Jander @ 2005-12-28 15:05 UTC (permalink / raw)
To: linuxppc-embedded
In-Reply-To: <20051228131939.GA17170@mail.gnudd.com>
Hi again,
On Wednesday 28 December 2005 14:19, Alessandro Rubini wrote:
> > The problem I see with Ocan is that it has a very different API than all
> > the others.
>
> I know. When I started the project there only was one driver, and
> it was already very complex. But it lacked the select method(now
> poll), and had other serious design problems. So I started mine,
> without advertising it.
Most of the time, that is the reason. There is something, but it's broken, and
to fix it is much more work that re-doing it. Problem is: some people are
already using it, and code is beeing grown on top of it. It seems a standard
open-source dilemma.
> Now I have a few happy users, and they want to keep my API in their
> applications, so I'm stuck with it.
Tough indeed. But according to Newton's laws, if we apply some force to it,
pointing in the right direction, eventually it'll move there, no matter how
big the object is. Let's try and find out where that direction is ;-)
> Yes, that is how things should be, in an ideal world.
Sorry for trying to be a bit of an idealist ;-)
> It would. Anyone willing to lead this effort? [no offence or humor
> intended, I am interested in following it, but can't lead it myself]
I have too little time and too little experience to do such a thing, but I'd
happily contribute and follow.
Regards,
--
David Jander
Protonic Holland.
^ permalink raw reply
* Re: Which CAN driver to port to for PPC
From: Andrey Volkov @ 2005-12-28 15:02 UTC (permalink / raw)
To: David Jander; +Cc: socket-can, r.schwebel, linuxppc-embedded
In-Reply-To: <200512281000.12073.david.jander@protonic.nl>
David Jander wrote:
> Hi all,
>
> On Tuesday 27 December 2005 22:49, Alessandro Rubini wrote:
>
>>I need to port ocan to support SJA1000 on an ARM device, as a client
>>asked for it. Also, another client asked for a 2.6 port, so all of
>>this will happen pretty soon (2-3 weeks). I don't know if that makes
>>any difference.
>
>
> That could of course make a difference.... eventually.
> The problem I see with Ocan is that it has a very different API than all the
> others. I know of at least two others, which try to be compatible (or at
> least easily portable between) with each other: lincan and can4linux. I am
> not sure but I think they started from the same base, and somehow agreed to
> stay API-compatible.
Robert Schwebel et al have worked socket based CAN (i.e. implement CAN
as _net_ dev, not as char), as consequence you will not have problem
with major/minor numbers, duplicated code in drivers for different
chips, could share CAN dev between diff processes _without_ misc. third
party shared libraies, stacked CAN protocols (CANopen/NMEA2000 could be
abstract kernel module)... But currently it is not open for everyone
(due to beta status, AFAIK)
Alessandro, please check Pengutronix work first, may be it will be
helpfull to you to,
Also I permit oneself to quotate _you_ ;) from LDDv3 pp6-7:
"The three classes are:
Character devices
A character (char) device is one that can be accessed as a stream of
bytes (like a file); a char driver is in charge of implementing this
behavior. Such a driver usually implements at least the open, close,
read, and write system calls. The text console (/dev/console) and the
serial ports (/dev/ttyS0 and friends) are examples of char devices, as
they are well represented by the stream abstraction. Char devices are
accessed by means of filesystem nodes, such as /dev/tty1 and /dev/lp0.
The only relevant difference between a char device and a regular file is
that you can always move back and forth in the regular file, whereas
most char devices are just data channels, which you can only access
sequentially. There exist, nonetheless, char devices that look like data
areas, and you can move back and forth in them; for instance, this
usually applies to frame grabbers, where the applications can access the
whole acquired image using mmap or lseek.
Block devices
Like char devices, block devices are accessed by filesystem nodes in the
/dev directory. A block device is a device (e.g., a disk) that can host
a filesystem. In most Unix systems, a block device can only handle I/O
operations that transfer one or more whole blocks, which are usually 512
bytes (or a larger power of two) bytes in length. Linux, instead, allows
the application to read and write a block device like a char device—it
permits the transfer of any number of bytes at a time. As a result,
block and char devices differ only in the way data is managed internally
by the kernel, and thus in the kernel/driver software interface. Like a
char device, each block device is accessed through a filesystem node,
and the difference between them is transparent to the user. Block
drivers have a completely different interface to the kernel than char
drivers.
Network interfaces
Any network transaction is made through an interface, that is, a device
that is able to exchange data with other hosts. Usually, an interface is
a hardware device, but it might also be a pure software device, like the
loopback interface. A network interface is in charge of sending and
receiving data packets, driven by the network subsystem of the kernel,
without knowing how individual transactions map to the actual packets
being transmitted. Many network connections (especially those using TCP)
are stream-oriented, but network devices are, usually, designed around
the transmission and receipt of packets. A network driver knows nothing
about individual connections; it only handles packets."
so CAN _is_ Network interface, but not char device
(how it often implemented).
P.S. Robert, when I check last time, it was mature enogh, so may be time
to open mail-list and svn?
--
Regards
Andrey Volkov
^ permalink raw reply
* Re: Porting Linux2.6.13 on MPC860T custom build board
From: Vitaly Bordug @ 2005-12-28 13:22 UTC (permalink / raw)
To: venkatajagadeesh p; +Cc: linuxppc-embedded
In-Reply-To: <20051228115847.559.qmail@web50403.mail.yahoo.com>
venkatajagadeesh p wrote:
>
> Hi,
> We are trying to port Linux-2.6.13 on Custom build MPC860T, board,
> We are unable to see any messages on console. We got the output given
> below. Please help us in porting the kernel.
> I am attaching the config file .
>
> =>bootm 0x100000
> ## Booting image at 00100000 ...
> Image Name: Linux-2.6.13
> Image Type: PowerPC Linux Kernel Image (gzip compressed)
> Data Size: 958189 Bytes = 935.7 kB
> Load Address: 00000000
> Entry Point: 00000000
> Verifying Checksum ... OK
> Uncompressing Kernel Image ... gunzip function called
> OK
> do_bootm_linux called ...do_bootm_linux after ...part2 do_boot_linux
> before RAM
> Disk image loading ...
> No initrd
> ## Transferring control to Linux (at address 00000000) ...
>
Most probably, something odd with serial setup.
You have enabled just all the stuff (SCC/SMC), but (on 8xx at least)
they can hardly live together, having alternative - conflicting IO pin configurations.
> ------------------------------------------------------------------------
> Yahoo! for Good - Make a difference this year.
> <http://us.rd.yahoo.com/mail_us/taglines/charity/*http://brand.yahoo.com/cybergivingweek2005/>
>
>
>
> ------------------------------------------------------------------------
>
> #
> # Automatically generated make config: don't edit
> # Linux kernel version: 2.6.13
> # Wed Dec 28 16:20:34 2005
> #
> CONFIG_MMU=y
> CONFIG_GENERIC_HARDIRQS=y
> CONFIG_RWSEM_XCHGADD_ALGORITHM=y
> CONFIG_GENERIC_CALIBRATE_DELAY=y
> CONFIG_HAVE_DEC_LOCK=y
> CONFIG_PPC=y
> CONFIG_PPC32=y
> CONFIG_GENERIC_NVRAM=y
> CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
>
> #
> # Code maturity level options
> #
> CONFIG_EXPERIMENTAL=y
> CONFIG_CLEAN_COMPILE=y
> CONFIG_BROKEN_ON_SMP=y
> CONFIG_INIT_ENV_ARG_LIMIT=32
>
> #
> # General setup
> #
> CONFIG_LOCALVERSION=""
> # CONFIG_SWAP is not set
> CONFIG_SYSVIPC=y
> # CONFIG_POSIX_MQUEUE is not set
> # CONFIG_BSD_PROCESS_ACCT is not set
> CONFIG_SYSCTL=y
> # CONFIG_AUDIT is not set
> # CONFIG_HOTPLUG is not set
> CONFIG_KOBJECT_UEVENT=y
> # CONFIG_IKCONFIG is not set
> # CONFIG_EMBEDDED is not set
> CONFIG_KALLSYMS=y
> # CONFIG_KALLSYMS_EXTRA_PASS is not set
> CONFIG_PRINTK=y
> CONFIG_BUG=y
> CONFIG_BASE_FULL=y
> CONFIG_FUTEX=y
> CONFIG_EPOLL=y
> CONFIG_SHMEM=y
> CONFIG_CC_ALIGN_FUNCTIONS=0
> CONFIG_CC_ALIGN_LABELS=0
> CONFIG_CC_ALIGN_LOOPS=0
> CONFIG_CC_ALIGN_JUMPS=0
> # CONFIG_TINY_SHMEM is not set
> CONFIG_BASE_SMALL=0
>
> #
> # Loadable module support
> #
> # CONFIG_MODULES is not set
>
> #
> # Processor
> #
> # CONFIG_6xx is not set
> # CONFIG_40x is not set
> # CONFIG_44x is not set
> # CONFIG_POWER3 is not set
> # CONFIG_POWER4 is not set
> CONFIG_8xx=y
> # CONFIG_E200 is not set
> # CONFIG_E500 is not set
> # CONFIG_MATH_EMULATION is not set
> # CONFIG_KEXEC is not set
> # CONFIG_CPU_FREQ is not set
> # CONFIG_WANT_EARLY_SERIAL is not set
> CONFIG_EMBEDDEDBOOT=y
> CONFIG_NOT_COHERENT_CACHE=y
>
> #
> # Platform options
> #
> CONFIG_FADS=y
> # CONFIG_RPXLITE is not set
> # CONFIG_RPXCLASSIC is not set
> # CONFIG_BSEIP is not set
> CONFIG_MPC8XXFADS=y
> # CONFIG_MPC86XADS is not set
> # CONFIG_MPC885ADS is not set
> # CONFIG_TQM823L is not set
> # CONFIG_TQM850L is not set
> # CONFIG_TQM855L is not set
> # CONFIG_TQM860L is not set
> # CONFIG_FPS850L is not set
> # CONFIG_SPD823TS is not set
> # CONFIG_IVMS8 is not set
> # CONFIG_IVML24 is not set
> # CONFIG_SM850 is not set
> # CONFIG_HERMES_PRO is not set
> # CONFIG_IP860 is not set
> # CONFIG_LWMON is not set
> # CONFIG_PCU_E is not set
> # CONFIG_CCM is not set
> # CONFIG_LANTEC is not set
> # CONFIG_MBX is not set
> # CONFIG_WINCEPT is not set
> # CONFIG_HIGHMEM is not set
> CONFIG_HZ_100=y
> # CONFIG_HZ_250 is not set
> # CONFIG_HZ_1000 is not set
> CONFIG_HZ=100
> CONFIG_PREEMPT_NONE=y
> # CONFIG_PREEMPT_VOLUNTARY is not set
> # CONFIG_PREEMPT is not set
> CONFIG_SELECT_MEMORY_MODEL=y
> CONFIG_FLATMEM_MANUAL=y
> # CONFIG_DISCONTIGMEM_MANUAL is not set
> # CONFIG_SPARSEMEM_MANUAL is not set
> CONFIG_FLATMEM=y
> CONFIG_FLAT_NODE_MEM_MAP=y
> CONFIG_BINFMT_ELF=y
> # CONFIG_BINFMT_MISC is not set
> # CONFIG_CMDLINE_BOOL is not set
> # CONFIG_PM is not set
> CONFIG_SECCOMP=y
> CONFIG_ISA_DMA_API=y
>
> #
> # Bus options
> #
> # CONFIG_PCI is not set
> # CONFIG_PCI_DOMAINS is not set
> # CONFIG_PCI_QSPAN is not set
>
> #
> # PCCARD (PCMCIA/CardBus) support
> #
> # CONFIG_PCCARD is not set
>
> #
> # Advanced setup
> #
> # CONFIG_ADVANCED_OPTIONS is not set
>
> #
> # Default settings for advanced configuration options are used
> #
> CONFIG_HIGHMEM_START=0xfe000000
> CONFIG_LOWMEM_SIZE=0x30000000
> CONFIG_KERNEL_START=0xc0000000
> CONFIG_TASK_SIZE=0x80000000
> CONFIG_CONSISTENT_START=0xff100000
> CONFIG_CONSISTENT_SIZE=0x00200000
> CONFIG_BOOT_LOAD=0x00400000
>
> #
> # Networking
> #
> CONFIG_NET=y
>
> #
> # Networking options
> #
> CONFIG_PACKET=y
> CONFIG_PACKET_MMAP=y
> CONFIG_UNIX=y
> # CONFIG_NET_KEY is not set
> CONFIG_INET=y
> # CONFIG_IP_MULTICAST is not set
> # CONFIG_IP_ADVANCED_ROUTER is not set
> CONFIG_IP_FIB_HASH=y
> CONFIG_IP_PNP=y
> CONFIG_IP_PNP_DHCP=y
> CONFIG_IP_PNP_BOOTP=y
> CONFIG_IP_PNP_RARP=y
> # CONFIG_NET_IPIP is not set
> # CONFIG_NET_IPGRE is not set
> CONFIG_ARPD=y
> # CONFIG_SYN_COOKIES is not set
> # CONFIG_INET_AH is not set
> # CONFIG_INET_ESP is not set
> # CONFIG_INET_IPCOMP is not set
> # CONFIG_INET_TUNNEL is not set
> CONFIG_IP_TCPDIAG=y
> CONFIG_IP_TCPDIAG_IPV6=y
> # CONFIG_TCP_CONG_ADVANCED is not set
> CONFIG_TCP_CONG_BIC=y
> CONFIG_IPV6=y
> # CONFIG_IPV6_PRIVACY is not set
> # CONFIG_INET6_AH is not set
> # CONFIG_INET6_ESP is not set
> # CONFIG_INET6_IPCOMP is not set
> # CONFIG_INET6_TUNNEL is not set
> # CONFIG_IPV6_TUNNEL is not set
> # CONFIG_NETFILTER is not set
>
> #
> # SCTP Configuration (EXPERIMENTAL)
> #
> # CONFIG_IP_SCTP is not set
> # CONFIG_ATM is not set
> CONFIG_BRIDGE=y
> # CONFIG_VLAN_8021Q is not set
> # CONFIG_DECNET is not set
> # CONFIG_LLC2 is not set
> # CONFIG_IPX is not set
> # CONFIG_ATALK is not set
> # CONFIG_X25 is not set
> # CONFIG_LAPB is not set
> # CONFIG_NET_DIVERT is not set
> # CONFIG_ECONET is not set
> # CONFIG_WAN_ROUTER is not set
> # CONFIG_NET_SCHED is not set
> # CONFIG_NET_CLS_ROUTE is not set
>
> #
> # Network testing
> #
> # CONFIG_NET_PKTGEN is not set
> # CONFIG_HAMRADIO is not set
> # CONFIG_IRDA is not set
> # CONFIG_BT is not set
>
> #
> # Device Drivers
> #
>
> #
> # Generic Driver Options
> #
> CONFIG_STANDALONE=y
> CONFIG_PREVENT_FIRMWARE_BUILD=y
> # CONFIG_FW_LOADER is not set
>
> #
> # Memory Technology Devices (MTD)
> #
> # CONFIG_MTD is not set
>
> #
> # Parallel port support
> #
> # CONFIG_PARPORT is not set
>
> #
> # Plug and Play support
> #
>
> #
> # Block devices
> #
> # CONFIG_BLK_DEV_FD is not set
> # CONFIG_BLK_DEV_COW_COMMON is not set
> # CONFIG_BLK_DEV_LOOP is not set
> # CONFIG_BLK_DEV_NBD is not set
> CONFIG_BLK_DEV_RAM=y
> CONFIG_BLK_DEV_RAM_COUNT=16
> CONFIG_BLK_DEV_RAM_SIZE=4096
> CONFIG_BLK_DEV_INITRD=y
> CONFIG_INITRAMFS_SOURCE=""
> # CONFIG_LBD is not set
> # CONFIG_CDROM_PKTCDVD is not set
>
> #
> # IO Schedulers
> #
> CONFIG_IOSCHED_NOOP=y
> # CONFIG_IOSCHED_AS is not set
> # CONFIG_IOSCHED_DEADLINE is not set
> # CONFIG_IOSCHED_CFQ is not set
> # CONFIG_ATA_OVER_ETH is not set
>
> #
> # ATA/ATAPI/MFM/RLL support
> #
> # CONFIG_IDE is not set
>
> #
> # SCSI device support
> #
> # CONFIG_SCSI is not set
>
> #
> # Multi-device support (RAID and LVM)
> #
> # CONFIG_MD is not set
>
> #
> # Fusion MPT device support
> #
> # CONFIG_FUSION is not set
>
> #
> # IEEE 1394 (FireWire) support
> #
>
> #
> # I2O device support
> #
>
> #
> # Macintosh device drivers
> #
>
> #
> # Network device support
> #
> CONFIG_NETDEVICES=y
> # CONFIG_DUMMY is not set
> # CONFIG_BONDING is not set
> # CONFIG_EQUALIZER is not set
> # CONFIG_TUN is not set
>
> #
> # Ethernet (10 or 100Mbit)
> #
> CONFIG_NET_ETHERNET=y
> CONFIG_MII=y
>
> #
> # Ethernet (1000 Mbit)
> #
>
> #
> # Ethernet (10000 Mbit)
> #
>
> #
> # Token Ring devices
> #
>
> #
> # Wireless LAN (non-hamradio)
> #
> # CONFIG_NET_RADIO is not set
>
> #
> # Wan interfaces
> #
> # CONFIG_WAN is not set
> # CONFIG_PPP is not set
> # CONFIG_SLIP is not set
> # CONFIG_SHAPER is not set
> # CONFIG_NETCONSOLE is not set
> # CONFIG_NETPOLL is not set
> # CONFIG_NET_POLL_CONTROLLER is not set
>
> #
> # ISDN subsystem
> #
> # CONFIG_ISDN is not set
>
> #
> # Telephony Support
> #
> # CONFIG_PHONE is not set
>
> #
> # Input device support
> #
> CONFIG_INPUT=y
>
> #
> # Userland interfaces
> #
> CONFIG_INPUT_MOUSEDEV=y
> CONFIG_INPUT_MOUSEDEV_PSAUX=y
> CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
> CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
> # CONFIG_INPUT_JOYDEV is not set
> # CONFIG_INPUT_TSDEV is not set
> # CONFIG_INPUT_EVDEV is not set
> # CONFIG_INPUT_EVBUG is not set
>
> #
> # Input Device Drivers
> #
> # CONFIG_INPUT_KEYBOARD is not set
> # CONFIG_INPUT_MOUSE is not set
> # CONFIG_INPUT_JOYSTICK is not set
> # CONFIG_INPUT_TOUCHSCREEN is not set
> # CONFIG_INPUT_MISC is not set
>
> #
> # Hardware I/O ports
> #
> # CONFIG_SERIO is not set
> # CONFIG_GAMEPORT is not set
>
> #
> # Character devices
> #
> CONFIG_VT=y
> CONFIG_VT_CONSOLE=y
> CONFIG_HW_CONSOLE=y
> CONFIG_SERIAL_NONSTANDARD=y
> # CONFIG_COMPUTONE is not set
> # CONFIG_ROCKETPORT is not set
> # CONFIG_CYCLADES is not set
> # CONFIG_DIGIEPCA is not set
> # CONFIG_MOXA_INTELLIO is not set
> # CONFIG_MOXA_SMARTIO is not set
> # CONFIG_ISI is not set
> # CONFIG_SYNCLINKMP is not set
> # CONFIG_N_HDLC is not set
> # CONFIG_RISCOM8 is not set
> # CONFIG_SPECIALIX is not set
> # CONFIG_SX is not set
> # CONFIG_RIO is not set
> # CONFIG_STALDRV is not set
>
> #
> # Serial drivers
> #
> # CONFIG_SERIAL_8250 is not set
>
> #
> # Non-8250 serial port support
> #
> CONFIG_SERIAL_CORE=y
> CONFIG_SERIAL_CORE_CONSOLE=y
> CONFIG_SERIAL_CPM=y
> CONFIG_SERIAL_CPM_CONSOLE=y
> CONFIG_SERIAL_CPM_SCC1=y
> CONFIG_SERIAL_CPM_SCC2=y
> # CONFIG_SERIAL_CPM_SCC3 is not set
> CONFIG_SERIAL_CPM_SCC4=y
> CONFIG_SERIAL_CPM_SMC1=y
> CONFIG_SERIAL_CPM_SMC2=y
> CONFIG_UNIX98_PTYS=y
> # CONFIG_LEGACY_PTYS is not set
>
> #
> # IPMI
> #
> # CONFIG_IPMI_HANDLER is not set
>
> #
> # Watchdog Cards
> #
> # CONFIG_WATCHDOG is not set
> # CONFIG_NVRAM is not set
> # CONFIG_GEN_RTC is not set
> # CONFIG_DTLK is not set
> # CONFIG_R3964 is not set
>
> #
> # Ftape, the floppy tape device driver
> #
> # CONFIG_AGP is not set
> # CONFIG_RAW_DRIVER is not set
>
> #
> # TPM devices
> #
>
> #
> # I2C support
> #
> # CONFIG_I2C is not set
> # CONFIG_I2C_SENSOR is not set
>
> #
> # Dallas's 1-wire bus
> #
> # CONFIG_W1 is not set
>
> #
> # Hardware Monitoring support
> #
> # CONFIG_HWMON is not set
>
> #
> # Misc devices
> #
>
> #
> # Multimedia devices
> #
> # CONFIG_VIDEO_DEV is not set
>
> #
> # Digital Video Broadcasting Devices
> #
> # CONFIG_DVB is not set
>
> #
> # Graphics support
> #
> # CONFIG_FB is not set
>
> #
> # Console display driver support
> #
> CONFIG_DUMMY_CONSOLE=y
>
> #
> # Sound
> #
> # CONFIG_SOUND is not set
>
> #
> # USB support
> #
> # CONFIG_USB_ARCH_HAS_HCD is not set
> # CONFIG_USB_ARCH_HAS_OHCI is not set
>
> #
> # USB Gadget Support
> #
> # CONFIG_USB_GADGET is not set
>
> #
> # MMC/SD Card support
> #
> # CONFIG_MMC is not set
>
> #
> # InfiniBand support
> #
>
> #
> # SN Devices
> #
>
> #
> # File systems
> #
> CONFIG_EXT2_FS=y
> CONFIG_EXT2_FS_XATTR=y
> CONFIG_EXT2_FS_POSIX_ACL=y
> CONFIG_EXT2_FS_SECURITY=y
> CONFIG_EXT2_FS_XIP=y
> CONFIG_FS_XIP=y
> # CONFIG_EXT3_FS is not set
> # CONFIG_JBD is not set
> CONFIG_FS_MBCACHE=y
> # CONFIG_REISERFS_FS is not set
> # CONFIG_JFS_FS is not set
> CONFIG_FS_POSIX_ACL=y
>
> #
> # XFS support
> #
> # CONFIG_XFS_FS is not set
> # CONFIG_MINIX_FS is not set
> CONFIG_ROMFS_FS=y
> CONFIG_INOTIFY=y
> # CONFIG_QUOTA is not set
> CONFIG_DNOTIFY=y
> # CONFIG_AUTOFS_FS is not set
> # CONFIG_AUTOFS4_FS is not set
>
> #
> # CD-ROM/DVD Filesystems
> #
> # CONFIG_ISO9660_FS is not set
> # CONFIG_UDF_FS is not set
>
> #
> # DOS/FAT/NT Filesystems
> #
> # CONFIG_MSDOS_FS is not set
> # CONFIG_VFAT_FS is not set
> # CONFIG_NTFS_FS is not set
>
> #
> # Pseudo filesystems
> #
> CONFIG_PROC_FS=y
> # CONFIG_PROC_KCORE is not set
> CONFIG_SYSFS=y
> # CONFIG_DEVPTS_FS_XATTR is not set
> # CONFIG_TMPFS is not set
> # CONFIG_HUGETLB_PAGE is not set
> CONFIG_RAMFS=y
>
> #
> # Miscellaneous filesystems
> #
> # CONFIG_ADFS_FS is not set
> # CONFIG_AFFS_FS is not set
> # CONFIG_HFS_FS is not set
> # CONFIG_HFSPLUS_FS is not set
> # CONFIG_BEFS_FS is not set
> # CONFIG_BFS_FS is not set
> # CONFIG_EFS_FS is not set
> # CONFIG_CRAMFS is not set
> # CONFIG_VXFS_FS is not set
> # CONFIG_HPFS_FS is not set
> # CONFIG_QNX4FS_FS is not set
> # CONFIG_SYSV_FS is not set
> # CONFIG_UFS_FS is not set
>
> #
> # Network File Systems
> #
> CONFIG_NFS_FS=y
> # CONFIG_NFS_V3 is not set
> # CONFIG_NFS_V4 is not set
> # CONFIG_NFS_DIRECTIO is not set
> # CONFIG_NFSD is not set
> CONFIG_ROOT_NFS=y
> CONFIG_LOCKD=y
> CONFIG_NFS_COMMON=y
> CONFIG_SUNRPC=y
> # CONFIG_RPCSEC_GSS_KRB5 is not set
> # CONFIG_RPCSEC_GSS_SPKM3 is not set
> # CONFIG_SMB_FS is not set
> # CONFIG_CIFS is not set
> # CONFIG_NCP_FS is not set
> # CONFIG_CODA_FS is not set
> # CONFIG_AFS_FS is not set
>
> #
> # Partition Types
> #
> # CONFIG_PARTITION_ADVANCED is not set
> CONFIG_MSDOS_PARTITION=y
>
> #
> # Native Language Support
> #
> # CONFIG_NLS is not set
>
> #
> # MPC8xx CPM Options
> #
> # CONFIG_SCC_ENET is not set
> CONFIG_FEC_ENET=y
> CONFIG_USE_MDIO=y
> CONFIG_FEC_AM79C874=y
> # CONFIG_FEC_LXT970 is not set
> # CONFIG_FEC_LXT971 is not set
> # CONFIG_FEC_QS6612 is not set
> CONFIG_ENET_BIG_BUFFERS=y
>
> #
> # Generic MPC8xx Options
> #
> # CONFIG_8xx_COPYBACK is not set
> # CONFIG_8xx_CPU6 is not set
> CONFIG_NO_UCODE_PATCH=y
> # CONFIG_USB_SOF_UCODE_PATCH is not set
> # CONFIG_I2C_SPI_UCODE_PATCH is not set
> # CONFIG_I2C_SPI_SMC1_UCODE_PATCH is not set
>
> #
> # Library routines
> #
> # CONFIG_CRC_CCITT is not set
> # CONFIG_CRC32 is not set
> # CONFIG_LIBCRC32C is not set
>
> #
> # Profiling support
> #
> # CONFIG_PROFILING is not set
>
> #
> # Kernel hacking
> #
> # CONFIG_PRINTK_TIME is not set
> # CONFIG_DEBUG_KERNEL is not set
> CONFIG_LOG_BUF_SHIFT=14
>
> #
> # Security options
> #
> # CONFIG_KEYS is not set
> # CONFIG_SECURITY is not set
>
> #
> # Cryptographic options
> #
> # CONFIG_CRYPTO is not set
>
> #
> # Hardware crypto devices
> #
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
--
Sincerely,
Vitaly
^ permalink raw reply
* Re: Which CAN driver to port to for PPC
From: Alessandro Rubini @ 2005-12-28 13:19 UTC (permalink / raw)
To: david.jander; +Cc: linuxppc-embedded
In-Reply-To: <200512281000.12073.david.jander@protonic.nl>
Hello.
> The problem I see with Ocan is that it has a very different API than all the
> others.
I know. When I started the project there only was one driver, and
it was already very complex. But it lacked the select method(now
poll), and had other serious design problems. So I started mine,
without advertising it.
Now I have a few happy users, and they want to keep my API in their
applications, so I'm stuck with it.
> I wonder how the port to SJA1000 will turn out, since I believe it
> would have to emulate some 82527-specific stuff, in order to offer a
> compatible API.
True, but the chip isn't _that_ different, actually.
> I am convinced though, that there should be a chip/card-independent
> API to the application-programmer, and that effort should be done to
> converge into the same direction.
Yes, that is how things should be, in an ideal world.
> So, wouldn't it be better to try to unite forces and at least offer
> similar API's, or even better, develop a standard linux CAN
> framework?
It would. Anyone willing to lead this effort? [no offence or humor
intended, I am interested in following it, but can't lead it myself]
Thanks for your comments
/alessandro
^ permalink raw reply
* Porting Linux2.6.13 on MPC860T custom build board
From: venkatajagadeesh p @ 2005-12-28 11:58 UTC (permalink / raw)
To: linuxppc-embedded
[-- Attachment #1.1: Type: text/plain, Size: 821 bytes --]
Hi,
We are trying to port Linux-2.6.13 on Custom build MPC860T, board, We are unable to see any messages on console. We got the output given below. Please help us in porting the kernel.
I am attaching the config file .
=>bootm 0x100000
## Booting image at 00100000 ...
Image Name: Linux-2.6.13
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 958189 Bytes = 935.7 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... gunzip function called
OK
do_bootm_linux called ...do_bootm_linux after ...part2 do_boot_linux before RAM
Disk image loading ...
No initrd
## Transferring control to Linux (at address 00000000) ...
---------------------------------
Yahoo! for Good - Make a difference this year.
[-- Attachment #1.2: Type: text/html, Size: 1248 bytes --]
[-- Attachment #2: 172188218-.config --]
[-- Type: text/plain, Size: 11858 bytes --]
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.13
# Wed Dec 28 16:20:34 2005
#
CONFIG_MMU=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_HAVE_DEC_LOCK=y
CONFIG_PPC=y
CONFIG_PPC32=y
CONFIG_GENERIC_NVRAM=y
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
#
CONFIG_LOCALVERSION=""
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
# CONFIG_HOTPLUG is not set
CONFIG_KOBJECT_UEVENT=y
# CONFIG_IKCONFIG is not set
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
#
# Loadable module support
#
# CONFIG_MODULES is not set
#
# Processor
#
# CONFIG_6xx is not set
# CONFIG_40x is not set
# CONFIG_44x is not set
# CONFIG_POWER3 is not set
# CONFIG_POWER4 is not set
CONFIG_8xx=y
# CONFIG_E200 is not set
# CONFIG_E500 is not set
# CONFIG_MATH_EMULATION is not set
# CONFIG_KEXEC is not set
# CONFIG_CPU_FREQ is not set
# CONFIG_WANT_EARLY_SERIAL is not set
CONFIG_EMBEDDEDBOOT=y
CONFIG_NOT_COHERENT_CACHE=y
#
# Platform options
#
CONFIG_FADS=y
# CONFIG_RPXLITE is not set
# CONFIG_RPXCLASSIC is not set
# CONFIG_BSEIP is not set
CONFIG_MPC8XXFADS=y
# CONFIG_MPC86XADS is not set
# CONFIG_MPC885ADS is not set
# CONFIG_TQM823L is not set
# CONFIG_TQM850L is not set
# CONFIG_TQM855L is not set
# CONFIG_TQM860L is not set
# CONFIG_FPS850L is not set
# CONFIG_SPD823TS is not set
# CONFIG_IVMS8 is not set
# CONFIG_IVML24 is not set
# CONFIG_SM850 is not set
# CONFIG_HERMES_PRO is not set
# CONFIG_IP860 is not set
# CONFIG_LWMON is not set
# CONFIG_PCU_E is not set
# CONFIG_CCM is not set
# CONFIG_LANTEC is not set
# CONFIG_MBX is not set
# CONFIG_WINCEPT is not set
# CONFIG_HIGHMEM is not set
CONFIG_HZ_100=y
# CONFIG_HZ_250 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=100
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_MISC is not set
# CONFIG_CMDLINE_BOOL is not set
# CONFIG_PM is not set
CONFIG_SECCOMP=y
CONFIG_ISA_DMA_API=y
#
# Bus options
#
# CONFIG_PCI is not set
# CONFIG_PCI_DOMAINS is not set
# CONFIG_PCI_QSPAN is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
#
# Advanced setup
#
# CONFIG_ADVANCED_OPTIONS is not set
#
# Default settings for advanced configuration options are used
#
CONFIG_HIGHMEM_START=0xfe000000
CONFIG_LOWMEM_SIZE=0x30000000
CONFIG_KERNEL_START=0xc0000000
CONFIG_TASK_SIZE=0x80000000
CONFIG_CONSISTENT_START=0xff100000
CONFIG_CONSISTENT_SIZE=0x00200000
CONFIG_BOOT_LOAD=0x00400000
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
CONFIG_ARPD=y
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_IP_TCPDIAG=y
CONFIG_IP_TCPDIAG_IPV6=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_BIC=y
CONFIG_IPV6=y
# CONFIG_IPV6_PRIVACY is not set
# CONFIG_INET6_AH is not set
# CONFIG_INET6_ESP is not set
# CONFIG_INET6_IPCOMP is not set
# CONFIG_INET6_TUNNEL is not set
# CONFIG_IPV6_TUNNEL is not set
# CONFIG_NETFILTER is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
CONFIG_BRIDGE=y
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_SCHED is not set
# CONFIG_NET_CLS_ROUTE is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
# CONFIG_PARPORT is not set
#
# Plug and Play support
#
#
# Block devices
#
# CONFIG_BLK_DEV_FD is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
# CONFIG_BLK_DEV_LOOP is not set
# CONFIG_BLK_DEV_NBD is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_LBD is not set
# CONFIG_CDROM_PKTCDVD is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
# CONFIG_IOSCHED_AS is not set
# CONFIG_IOSCHED_DEADLINE is not set
# CONFIG_IOSCHED_CFQ is not set
# CONFIG_ATA_OVER_ETH is not set
#
# ATA/ATAPI/MFM/RLL support
#
# CONFIG_IDE is not set
#
# SCSI device support
#
# CONFIG_SCSI is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
#
#
# I2O device support
#
#
# Macintosh device drivers
#
#
# Network device support
#
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
#
# Ethernet (1000 Mbit)
#
#
# Ethernet (10000 Mbit)
#
#
# Token Ring devices
#
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set
#
# Input Device Drivers
#
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
#
# Hardware I/O ports
#
# CONFIG_SERIO is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_SERIAL_NONSTANDARD=y
# CONFIG_COMPUTONE is not set
# CONFIG_ROCKETPORT is not set
# CONFIG_CYCLADES is not set
# CONFIG_DIGIEPCA is not set
# CONFIG_MOXA_INTELLIO is not set
# CONFIG_MOXA_SMARTIO is not set
# CONFIG_ISI is not set
# CONFIG_SYNCLINKMP is not set
# CONFIG_N_HDLC is not set
# CONFIG_RISCOM8 is not set
# CONFIG_SPECIALIX is not set
# CONFIG_SX is not set
# CONFIG_RIO is not set
# CONFIG_STALDRV is not set
#
# Serial drivers
#
# CONFIG_SERIAL_8250 is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_CPM=y
CONFIG_SERIAL_CPM_CONSOLE=y
CONFIG_SERIAL_CPM_SCC1=y
CONFIG_SERIAL_CPM_SCC2=y
# CONFIG_SERIAL_CPM_SCC3 is not set
CONFIG_SERIAL_CPM_SCC4=y
CONFIG_SERIAL_CPM_SMC1=y
CONFIG_SERIAL_CPM_SMC2=y
CONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_NVRAM is not set
# CONFIG_GEN_RTC is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_AGP is not set
# CONFIG_RAW_DRIVER is not set
#
# TPM devices
#
#
# I2C support
#
# CONFIG_I2C is not set
# CONFIG_I2C_SENSOR is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
#
# Hardware Monitoring support
#
# CONFIG_HWMON is not set
#
# Misc devices
#
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
#
# Graphics support
#
# CONFIG_FB is not set
#
# Console display driver support
#
CONFIG_DUMMY_CONSOLE=y
#
# Sound
#
# CONFIG_SOUND is not set
#
# USB support
#
# CONFIG_USB_ARCH_HAS_HCD is not set
# CONFIG_USB_ARCH_HAS_OHCI is not set
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
#
# MMC/SD Card support
#
# CONFIG_MMC is not set
#
# InfiniBand support
#
#
# SN Devices
#
#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
CONFIG_EXT2_FS_XIP=y
CONFIG_FS_XIP=y
# CONFIG_EXT3_FS is not set
# CONFIG_JBD is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
#
# XFS support
#
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
CONFIG_ROMFS_FS=y
CONFIG_INOTIFY=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
# CONFIG_UDF_FS is not set
#
# DOS/FAT/NT Filesystems
#
# CONFIG_MSDOS_FS is not set
# CONFIG_VFAT_FS is not set
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
# CONFIG_PROC_KCORE is not set
CONFIG_SYSFS=y
# CONFIG_DEVPTS_FS_XATTR is not set
# CONFIG_TMPFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
CONFIG_NFS_FS=y
# CONFIG_NFS_V3 is not set
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
#
# Native Language Support
#
# CONFIG_NLS is not set
#
# MPC8xx CPM Options
#
# CONFIG_SCC_ENET is not set
CONFIG_FEC_ENET=y
CONFIG_USE_MDIO=y
CONFIG_FEC_AM79C874=y
# CONFIG_FEC_LXT970 is not set
# CONFIG_FEC_LXT971 is not set
# CONFIG_FEC_QS6612 is not set
CONFIG_ENET_BIG_BUFFERS=y
#
# Generic MPC8xx Options
#
# CONFIG_8xx_COPYBACK is not set
# CONFIG_8xx_CPU6 is not set
CONFIG_NO_UCODE_PATCH=y
# CONFIG_USB_SOF_UCODE_PATCH is not set
# CONFIG_I2C_SPI_UCODE_PATCH is not set
# CONFIG_I2C_SPI_SMC1_UCODE_PATCH is not set
#
# Library routines
#
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC32 is not set
# CONFIG_LIBCRC32C is not set
#
# Profiling support
#
# CONFIG_PROFILING is not set
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_LOG_BUF_SHIFT=14
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
# CONFIG_CRYPTO is not set
#
# Hardware crypto devices
#
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox