* Re: cpu power "management" for non-dfs chips with no pmu (for instance, 750cxe and mpc7447 in pegasos)
From: Jon Loeliger @ 2006-06-24 16:16 UTC (permalink / raw)
To: Guennadi Liakhovetski; +Cc: linuxppc-dev
In-Reply-To: <Pine.LNX.4.60.0606240147560.15705@poirot.grange>
So, like, the other day Guennadi Liakhovetski mumbled:
> On Fri, 23 Jun 2006, Jon Loeliger wrote:
>
> > See? You _are_ contributing already. I encourage
> > you to hit the linux-pm@lists.osdl.org list for a spell!
> >
> > You could start here:
> > https://lists.osdl.org/mailman/listinfo/linux-pm
>
> Sorry, I looked at the list archives and didn't find any search, could
> you, please, post a link to the thread or the subject line?
Perhaps there was some misunderstanding of what I was
trying to say.
I am NOT saying that they have solved your question with
regard to the 7447 or pagasos directly. I have no specific
thread to refer to you.
I AM saying that there is renewed interest in the topic of
Linux Power Managament. Questions, suggestions and interested
parties should gather and discuss things on the linux-pm
list host on osdl.org. That is likely the best place to ask
this question and get a feel for an answer.
Thanks,
jdl
^ permalink raw reply
* Re: [PATCH 5/6] CPM_UART: unify clock sources
From: Kumar Gala @ 2006-06-24 15:50 UTC (permalink / raw)
To: Vitaly Bordug; +Cc: linuxppc-dev
In-Reply-To: <20060624192136.41e9987d@localhost.localdomain>
On Jun 24, 2006, at 10:21 AM, Vitaly Bordug wrote:
> Kumar,
>
> Thanks for feedback! My comment below.
>
> On Sat, 24 Jun 2006 08:46:54 -0500
> Kumar Gala <galak@kernel.crashing.org> wrote:
>
> [snip]
>>> +
>>> +#ifndef FS_PD_H
>>> +#define FS_PD_H
>>> +
>>> +#define GET_BAUDRATE() (((bd_t *) __res)->bi_baudrate ?
>>> ((bd_t *) __res)->bi_baudrate : -1)
>>> +#define FS_UART_CLK() (((bd_t *) __res)->bi_intfreq)
>>> +
>>> +#endif
>>
>> We shouldn't hide these differences in a header like this. As we
>> slowly try to removing things from arch/ppc. Why not just add
>> platform data for these two pieces of data and set it up like we do
>> other platform data.
>>
> That was my first guess as well, but:
> The aim is yet moving to powerpc not to break existing ppc/ stuff.
> So if alternatively platform_data may be utilized, all relevant ppc
> stuff that uses cpm uart should be updated. While doing the driver
> "platformize" trick, I made it possible to keep legacy behaviour
> (pd-less), this is not going to afford such a thing.
>
> IOW, I don't see much sense in updating ppc/ BSP files, just to keep
> the right way. It does not look very neat now, but does the job of
> moving FW and keeping existing stuff sane. If there is better approach
> envisioned, I'll definitely follow..
Fair enough, then I would suggest getting ride of all this header/
MACRO indirection and just implement these as functions with
different implementations in arch/powerpc vs arch/ppc.
- k
^ permalink raw reply
* Re: [PATCH 5/6] CPM_UART: unify clock sources
From: Vitaly Bordug @ 2006-06-24 15:21 UTC (permalink / raw)
To: Kumar Gala; +Cc: linuxppc-dev
In-Reply-To: <10C0FB27-7351-4578-9CE5-3EFA476C2661@kernel.crashing.org>
Kumar,
Thanks for feedback! My comment below.
On Sat, 24 Jun 2006 08:46:54 -0500
Kumar Gala <galak@kernel.crashing.org> wrote:
[snip]
> > +
> > +#ifndef FS_PD_H
> > +#define FS_PD_H
> > +
> > +#define GET_BAUDRATE() (((bd_t *) __res)->bi_baudrate ?
> > ((bd_t *) __res)->bi_baudrate : -1)
> > +#define FS_UART_CLK() (((bd_t *) __res)->bi_intfreq)
> > +
> > +#endif
>
> We shouldn't hide these differences in a header like this. As we
> slowly try to removing things from arch/ppc. Why not just add
> platform data for these two pieces of data and set it up like we do
> other platform data.
>
That was my first guess as well, but:
The aim is yet moving to powerpc not to break existing ppc/ stuff.
So if alternatively platform_data may be utilized, all relevant ppc
stuff that uses cpm uart should be updated. While doing the driver
"platformize" trick, I made it possible to keep legacy behaviour
(pd-less), this is not going to afford such a thing.
IOW, I don't see much sense in updating ppc/ BSP files, just to keep
the right way. It does not look very neat now, but does the job of
moving FW and keeping existing stuff sane. If there is better approach
envisioned, I'll definitely follow..
--
Sincerely, Vitaly
^ permalink raw reply
* Re: [PATCH 5/6] CPM_UART: unify clock sources
From: Kumar Gala @ 2006-06-24 13:46 UTC (permalink / raw)
To: Vitaly Bordug; +Cc: linuxppc-dev
In-Reply-To: <20060623231707.6721.43277.stgit@localhost.localdomain>
On Jun 23, 2006, at 6:17 PM, Vitaly Bordug wrote:
>
> In order to make it possible to utilize the driver from arch/
> powerpc yet not
> breaking existing ppc users, clock sources are unfied via macro, and
> resources ioremapped.
>
> Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
> ---
>
> drivers/serial/cpm_uart/cpm_uart_core.c | 11 ++++-------
> drivers/serial/cpm_uart/cpm_uart_cpm2.c | 13 +++++++------
> include/asm-powerpc/fs_pd.h | 17 +++++++++++++++++
> include/asm-ppc/fs_pd.h | 17 +++++++++++++++++
> 4 files changed, 45 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c b/drivers/
> serial/cpm_uart/cpm_uart_core.c
> index 5cba59a..0507f74 100644
> --- a/drivers/serial/cpm_uart/cpm_uart_core.c
> +++ b/drivers/serial/cpm_uart/cpm_uart_core.c
> @@ -47,6 +47,7 @@ #include <linux/fs_uart_pd.h>
> #include <asm/io.h>
> #include <asm/irq.h>
> #include <asm/delay.h>
> +#include <asm/fs_pd.h>
>
> #if defined(CONFIG_SERIAL_CPM_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
> #define SUPPORT_SYSRQ
> @@ -1045,11 +1046,11 @@ int cpm_uart_drv_get_platform_data(struc
>
> if (!(r = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> "regs")))
> return -EINVAL;
> - mem = r->start;
> + mem = ioremap(r->start, r->end - r->start + 1);
>
> if (!(r = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> "pram")))
> return -EINVAL;
> - pram = r->start;
> + pram = ioremap(r->start, r->end - r->start + 1);
>
> if(idx > fsid_smc2_uart) {
> pinfo->sccp = (scc_t *)mem;
> @@ -1190,11 +1191,7 @@ static int __init cpm_uart_console_setup
> if (options) {
> uart_parse_options(options, &baud, &parity, &bits, &flow);
> } else {
> - bd_t *bd = (bd_t *) __res;
> -
> - if (bd->bi_baudrate)
> - baud = bd->bi_baudrate;
> - else
> + if ((baud = GET_BAUDRATE()) == -1)
> baud = 9600;
> }
>
> diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm2.c b/drivers/
> serial/cpm_uart/cpm_uart_cpm2.c
> index cdba128..29b89f0 100644
> --- a/drivers/serial/cpm_uart/cpm_uart_cpm2.c
> +++ b/drivers/serial/cpm_uart/cpm_uart_cpm2.c
> @@ -41,6 +41,7 @@ #include <linux/dma-mapping.h>
>
> #include <asm/io.h>
> #include <asm/irq.h>
> +#include <asm/fs_pd.h>
>
> #include <linux/serial_core.h>
> #include <linux/kernel.h>
> @@ -267,7 +268,7 @@ #ifdef CONFIG_SERIAL_CPM_SMC1
> (unsigned long)&cpm2_immr->im_smc[0];
> cpm_uart_ports[UART_SMC1].smcp->smc_smcm |= (SMCM_RX | SMCM_TX);
> cpm_uart_ports[UART_SMC1].smcp->smc_smcmr &= ~(SMCMR_REN |
> SMCMR_TEN);
> - cpm_uart_ports[UART_SMC1].port.uartclk = (((bd_t *) __res)-
> >bi_intfreq);
> + cpm_uart_ports[UART_SMC1].port.uartclk = FS_UART_CLK();
> cpm_uart_port_map[cpm_uart_nr++] = UART_SMC1;
> #endif
>
> @@ -280,7 +281,7 @@ #ifdef CONFIG_SERIAL_CPM_SMC2
> (unsigned long)&cpm2_immr->im_smc[1];
> cpm_uart_ports[UART_SMC2].smcp->smc_smcm |= (SMCM_RX | SMCM_TX);
> cpm_uart_ports[UART_SMC2].smcp->smc_smcmr &= ~(SMCMR_REN |
> SMCMR_TEN);
> - cpm_uart_ports[UART_SMC2].port.uartclk = (((bd_t *) __res)-
> >bi_intfreq);
> + cpm_uart_ports[UART_SMC2].port.uartclk = FS_UART_CLK();
> cpm_uart_port_map[cpm_uart_nr++] = UART_SMC2;
> #endif
>
> @@ -294,7 +295,7 @@ #ifdef CONFIG_SERIAL_CPM_SCC1
> ~(UART_SCCM_TX | UART_SCCM_RX);
> cpm_uart_ports[UART_SCC1].sccp->scc_gsmrl &=
> ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
> - cpm_uart_ports[UART_SCC1].port.uartclk = (((bd_t *) __res)-
> >bi_intfreq);
> + cpm_uart_ports[UART_SCC1].port.uartclk = FS_UART_CLK();
> cpm_uart_port_map[cpm_uart_nr++] = UART_SCC1;
> #endif
>
> @@ -308,7 +309,7 @@ #ifdef CONFIG_SERIAL_CPM_SCC2
> ~(UART_SCCM_TX | UART_SCCM_RX);
> cpm_uart_ports[UART_SCC2].sccp->scc_gsmrl &=
> ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
> - cpm_uart_ports[UART_SCC2].port.uartclk = (((bd_t *) __res)-
> >bi_intfreq);
> + cpm_uart_ports[UART_SCC2].port.uartclk = FS_UART_CLK();
> cpm_uart_port_map[cpm_uart_nr++] = UART_SCC2;
> #endif
>
> @@ -322,7 +323,7 @@ #ifdef CONFIG_SERIAL_CPM_SCC3
> ~(UART_SCCM_TX | UART_SCCM_RX);
> cpm_uart_ports[UART_SCC3].sccp->scc_gsmrl &=
> ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
> - cpm_uart_ports[UART_SCC3].port.uartclk = (((bd_t *) __res)-
> >bi_intfreq);
> + cpm_uart_ports[UART_SCC3].port.uartclk = FS_UART_CLK();
> cpm_uart_port_map[cpm_uart_nr++] = UART_SCC3;
> #endif
>
> @@ -336,7 +337,7 @@ #ifdef CONFIG_SERIAL_CPM_SCC4
> ~(UART_SCCM_TX | UART_SCCM_RX);
> cpm_uart_ports[UART_SCC4].sccp->scc_gsmrl &=
> ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
> - cpm_uart_ports[UART_SCC4].port.uartclk = (((bd_t *) __res)-
> >bi_intfreq);
> + cpm_uart_ports[UART_SCC4].port.uartclk = FS_UART_CLK();
> cpm_uart_port_map[cpm_uart_nr++] = UART_SCC4;
> #endif
>
> diff --git a/include/asm-powerpc/fs_pd.h b/include/asm-powerpc/fs_pd.h
> new file mode 100644
> index 0000000..b20d8da
> --- /dev/null
> +++ b/include/asm-powerpc/fs_pd.h
> @@ -0,0 +1,17 @@
> +/*
> + * Platform information definitions.
> + *
> + * 2006 (c) MontaVista Software, Inc.
> + *
> + * This file is licensed under the terms of the GNU General Public
> License
> + * version 2. This program is licensed "as is" without any
> warranty of any
> + * kind, whether express or implied.
> + */
> +
> +#ifndef FS_PD_H
> +#define FS_PD_H
> +
> +#define GET_BAUDRATE() get_baudrate()
> +#define FS_UART_CLK() get_intfreq()
> +
> +#endif
> diff --git a/include/asm-ppc/fs_pd.h b/include/asm-ppc/fs_pd.h
> new file mode 100644
> index 0000000..b1d550b
> --- /dev/null
> +++ b/include/asm-ppc/fs_pd.h
> @@ -0,0 +1,17 @@
> +/*
> + * Platform information definitions.
> + *
> + * 2006 (c) MontaVista Software, Inc.
> + *
> + * This file is licensed under the terms of the GNU General Public
> License
> + * version 2. This program is licensed "as is" without any
> warranty of any
> + * kind, whether express or implied.
> + */
> +
> +#ifndef FS_PD_H
> +#define FS_PD_H
> +
> +#define GET_BAUDRATE() (((bd_t *) __res)->bi_baudrate ? ((bd_t *)
> __res)->bi_baudrate : -1)
> +#define FS_UART_CLK() (((bd_t *) __res)->bi_intfreq)
> +
> +#endif
We shouldn't hide these differences in a header like this. As we
slowly try to removing things from arch/ppc. Why not just add
platform data for these two pieces of data and set it up like we do
other platform data.
- k
^ permalink raw reply
* [PATCH 0/6] Add mpc8560 support to powerpc
From: Vitaly Bordug @ 2006-06-23 23:59 UTC (permalink / raw)
To: linuxppc-dev@ozlabs.org
This is a first preliminary series to move 8560ads to powerpc and hence finish
85xx family in terms of merge. Subsequient fs_enet patches are strictly required
for the following to work, but submitted here as reference only
(will be updated and sent to netdev shortly).
ATM not all points are adressed, there still may be bugs, but in general it works and have most
of the SoC stuff (UARTs, Gig eth, 100BaseT FCC) as well as the PCI stuff.
All the comments are greatly appreciated.
--
Sincerely, Vitaly
^ permalink raw reply
* Re: cpu power "management" for non-dfs chips with no pmu (for instance, 750cxe and mpc7447 in pegasos)
From: Guennadi Liakhovetski @ 2006-06-23 23:49 UTC (permalink / raw)
To: Jon Loeliger; +Cc: linuxppc-dev
In-Reply-To: <E1Ftmcb-0007rG-QS@jdl.com>
On Fri, 23 Jun 2006, Jon Loeliger wrote:
> See? You _are_ contributing already. I encourage
> you to hit the linux-pm@lists.osdl.org list for a spell!
>
> You could start here:
> https://lists.osdl.org/mailman/listinfo/linux-pm
Sorry, I looked at the list archives and didn't find any search, could
you, please, post a link to the thread or the subject line?
Thanks
Guennadi
---
Guennadi Liakhovetski
^ permalink raw reply
* [PATCH 2/6] FS_ENET: Utilize Phy abstraction
From: Vitaly Bordug @ 2006-06-23 23:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <20060623231648.6721.3495.stgit@localhost.localdomain>
This part has modifications necessary to make fs_enet use Phy Abstraction
Layer. All mdio trasports were supported, including FEC and bitbanging via
GPIO.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
---
drivers/net/fs_enet/Makefile | 6
drivers/net/fs_enet/fec.h | 42 +++
drivers/net/fs_enet/fs_enet-main.c | 207 +++++++++------
drivers/net/fs_enet/fs_enet-mii.c | 507 ------------------------------------
drivers/net/fs_enet/fs_enet.h | 40 ++-
drivers/net/fs_enet/mac-fcc.c | 32 ++
drivers/net/fs_enet/mac-fec.c | 132 +--------
drivers/net/fs_enet/mac-scc.c | 4
drivers/net/fs_enet/mii-bitbang.c | 462 +++++++++++++++++----------------
drivers/net/fs_enet/mii-fec.c | 243 +++++++++++++++++
drivers/net/fs_enet/mii-fixed.c | 92 -------
11 files changed, 713 insertions(+), 1054 deletions(-)
diff --git a/drivers/net/fs_enet/Makefile b/drivers/net/fs_enet/Makefile
index d6dd3f2..02d4dc1 100644
--- a/drivers/net/fs_enet/Makefile
+++ b/drivers/net/fs_enet/Makefile
@@ -4,7 +4,7 @@ #
obj-$(CONFIG_FS_ENET) += fs_enet.o
-obj-$(CONFIG_8xx) += mac-fec.o mac-scc.o
-obj-$(CONFIG_8260) += mac-fcc.o
+obj-$(CONFIG_8xx) += mac-fec.o mac-scc.o mii-fec.o
+obj-$(CONFIG_CPM2) += mac-fcc.o mii-bitbang.o
-fs_enet-objs := fs_enet-main.o fs_enet-mii.o mii-bitbang.o mii-fixed.o
+fs_enet-objs := fs_enet-main.o
diff --git a/drivers/net/fs_enet/fec.h b/drivers/net/fs_enet/fec.h
new file mode 100644
index 0000000..e980527
--- /dev/null
+++ b/drivers/net/fs_enet/fec.h
@@ -0,0 +1,42 @@
+#ifndef FS_ENET_FEC_H
+#define FS_ENET_FEC_H
+
+/* CRC polynomium used by the FEC for the multicast group filtering */
+#define FEC_CRC_POLY 0x04C11DB7
+
+#define FEC_MAX_MULTICAST_ADDRS 64
+
+/* Interrupt events/masks.
+*/
+#define FEC_ENET_HBERR 0x80000000U /* Heartbeat error */
+#define FEC_ENET_BABR 0x40000000U /* Babbling receiver */
+#define FEC_ENET_BABT 0x20000000U /* Babbling transmitter */
+#define FEC_ENET_GRA 0x10000000U /* Graceful stop complete */
+#define FEC_ENET_TXF 0x08000000U /* Full frame transmitted */
+#define FEC_ENET_TXB 0x04000000U /* A buffer was transmitted */
+#define FEC_ENET_RXF 0x02000000U /* Full frame received */
+#define FEC_ENET_RXB 0x01000000U /* A buffer was received */
+#define FEC_ENET_MII 0x00800000U /* MII interrupt */
+#define FEC_ENET_EBERR 0x00400000U /* SDMA bus error */
+
+#define FEC_ECNTRL_PINMUX 0x00000004
+#define FEC_ECNTRL_ETHER_EN 0x00000002
+#define FEC_ECNTRL_RESET 0x00000001
+
+#define FEC_RCNTRL_BC_REJ 0x00000010
+#define FEC_RCNTRL_PROM 0x00000008
+#define FEC_RCNTRL_MII_MODE 0x00000004
+#define FEC_RCNTRL_DRT 0x00000002
+#define FEC_RCNTRL_LOOP 0x00000001
+
+#define FEC_TCNTRL_FDEN 0x00000004
+#define FEC_TCNTRL_HBC 0x00000002
+#define FEC_TCNTRL_GTS 0x00000001
+
+
+
+/*
+ * Delay to wait for FEC reset command to complete (in us)
+ */
+#define FEC_RESET_DELAY 50
+#endif
diff --git a/drivers/net/fs_enet/fs_enet-main.c b/drivers/net/fs_enet/fs_enet-main.c
index 196298f..302ecaa 100644
--- a/drivers/net/fs_enet/fs_enet-main.c
+++ b/drivers/net/fs_enet/fs_enet-main.c
@@ -38,6 +38,7 @@ #include <linux/ethtool.h>
#include <linux/bitops.h>
#include <linux/fs.h>
#include <linux/platform_device.h>
+#include <linux/phy.h>
#include <linux/vmalloc.h>
#include <asm/pgtable.h>
@@ -683,35 +684,6 @@ static void fs_free_irq(struct net_devic
(*fep->ops->post_free_irq)(dev, irq);
}
-/**********************************************************************************/
-
-/* This interrupt occurs when the PHY detects a link change. */
-static irqreturn_t
-fs_mii_link_interrupt(int irq, void *dev_id, struct pt_regs *regs)
-{
- struct net_device *dev = dev_id;
- struct fs_enet_private *fep;
- const struct fs_platform_info *fpi;
-
- fep = netdev_priv(dev);
- fpi = fep->fpi;
-
- /*
- * Acknowledge the interrupt if possible. If we have not
- * found the PHY yet we can't process or acknowledge the
- * interrupt now. Instead we ignore this interrupt for now,
- * which we can do since it is edge triggered. It will be
- * acknowledged later by fs_enet_open().
- */
- if (!fep->phy)
- return IRQ_NONE;
-
- fs_mii_ack_int(dev);
- fs_mii_link_status_change_check(dev, 0);
-
- return IRQ_HANDLED;
-}
-
static void fs_timeout(struct net_device *dev)
{
struct fs_enet_private *fep = netdev_priv(dev);
@@ -723,67 +695,146 @@ static void fs_timeout(struct net_device
spin_lock_irqsave(&fep->lock, flags);
if (dev->flags & IFF_UP) {
+ phy_stop(fep->phydev);
(*fep->ops->stop)(dev);
(*fep->ops->restart)(dev);
+ phy_start(fep->phydev);
}
+ phy_start(fep->phydev);
wake = fep->tx_free && !(CBDR_SC(fep->cur_tx) & BD_ENET_TX_READY);
spin_unlock_irqrestore(&fep->lock, flags);
if (wake)
netif_wake_queue(dev);
+}
+
+/*-----------------------------------------------------------------------------
+ * generic link-change handler - should be sufficient for most cases
+ *-----------------------------------------------------------------------------*/
+static void generic_adjust_link(struct net_device *dev)
+{
+ struct fs_enet_private *fep = netdev_priv(dev);
+ struct phy_device *phydev = fep->phydev;
+ int new_state = 0;
+
+ if (phydev->link) {
+
+ /* adjust to duplex mode */
+ if (phydev->duplex != fep->oldduplex){
+ new_state = 1;
+ fep->oldduplex = phydev->duplex;
+ }
+
+ if (phydev->speed != fep->oldspeed) {
+ new_state = 1;
+ fep->oldspeed = phydev->speed;
+ }
+
+ if (!fep->oldlink) {
+ new_state = 1;
+ fep->oldlink = 1;
+ netif_schedule(dev);
+ netif_carrier_on(dev);
+ netif_start_queue(dev);
+ }
+
+ if (new_state)
+ fep->ops->restart(dev);
+
+ } else if (fep->oldlink) {
+ new_state = 1;
+ fep->oldlink = 0;
+ fep->oldspeed = 0;
+ fep->oldduplex = -1;
+ netif_carrier_off(dev);
+ netif_stop_queue(dev);
+ }
+
+ if (new_state && netif_msg_link(fep))
+ phy_print_status(phydev);
+}
+
+
+static void fs_adjust_link(struct net_device *dev)
+{
+ struct fs_enet_private *fep = netdev_priv(dev);
+ unsigned long flags;
+
+ spin_lock_irqsave(&fep->lock, flags);
+
+ if(fep->ops->adjust_link)
+ fep->ops->adjust_link(dev);
+ else
+ generic_adjust_link(dev);
+
+ spin_unlock_irqrestore(&fep->lock, flags);
+}
+
+static int fs_init_phy(struct net_device *dev)
+{
+ struct fs_enet_private *fep = netdev_priv(dev);
+ struct phy_device *phydev;
+
+ fep->oldlink = 0;
+ fep->oldspeed = 0;
+ fep->oldduplex = -1;
+ if(fep->fpi->bus_id)
+ phydev = phy_connect(dev, fep->fpi->bus_id, &fs_adjust_link, 0);
+ else {
+ printk("No phy bus ID specified in BSP code\n");
+ return -EINVAL;
+ }
+ if (IS_ERR(phydev)) {
+ printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
+ return PTR_ERR(phydev);
+ }
+
+ fep->phydev = phydev;
+
+ return 0;
}
+
static int fs_enet_open(struct net_device *dev)
{
struct fs_enet_private *fep = netdev_priv(dev);
- const struct fs_platform_info *fpi = fep->fpi;
int r;
+ int err;
/* Install our interrupt handler. */
r = fs_request_irq(dev, fep->interrupt, "fs_enet-mac", fs_enet_interrupt);
if (r != 0) {
printk(KERN_ERR DRV_MODULE_NAME
- ": %s Could not allocate FEC IRQ!", dev->name);
+ ": %s Could not allocate FS_ENET IRQ!", dev->name);
return -EINVAL;
}
- /* Install our phy interrupt handler */
- if (fpi->phy_irq != -1) {
+ err = fs_init_phy(dev);
+ if(err)
+ return err;
- r = fs_request_irq(dev, fpi->phy_irq, "fs_enet-phy", fs_mii_link_interrupt);
- if (r != 0) {
- printk(KERN_ERR DRV_MODULE_NAME
- ": %s Could not allocate PHY IRQ!", dev->name);
- fs_free_irq(dev, fep->interrupt);
- return -EINVAL;
- }
- }
+ phy_start(fep->phydev);
- fs_mii_startup(dev);
- netif_carrier_off(dev);
- fs_mii_link_status_change_check(dev, 1);
-
return 0;
}
static int fs_enet_close(struct net_device *dev)
{
struct fs_enet_private *fep = netdev_priv(dev);
- const struct fs_platform_info *fpi = fep->fpi;
unsigned long flags;
netif_stop_queue(dev);
netif_carrier_off(dev);
- fs_mii_shutdown(dev);
+ phy_stop(fep->phydev);
spin_lock_irqsave(&fep->lock, flags);
(*fep->ops->stop)(dev);
spin_unlock_irqrestore(&fep->lock, flags);
/* release any irqs */
- if (fpi->phy_irq != -1)
- fs_free_irq(dev, fpi->phy_irq);
+ phy_disconnect(fep->phydev);
+ fep->phydev = NULL;
fs_free_irq(dev, fep->interrupt);
return 0;
@@ -831,33 +882,19 @@ static void fs_get_regs(struct net_devic
static int fs_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
{
struct fs_enet_private *fep = netdev_priv(dev);
- unsigned long flags;
- int rc;
-
- spin_lock_irqsave(&fep->lock, flags);
- rc = mii_ethtool_gset(&fep->mii_if, cmd);
- spin_unlock_irqrestore(&fep->lock, flags);
-
- return rc;
+ return phy_ethtool_gset(fep->phydev, cmd);
}
static int fs_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
{
struct fs_enet_private *fep = netdev_priv(dev);
- unsigned long flags;
- int rc;
-
- spin_lock_irqsave(&fep->lock, flags);
- rc = mii_ethtool_sset(&fep->mii_if, cmd);
- spin_unlock_irqrestore(&fep->lock, flags);
-
- return rc;
+ phy_ethtool_sset(fep->phydev, cmd);
+ return 0;
}
static int fs_nway_reset(struct net_device *dev)
{
- struct fs_enet_private *fep = netdev_priv(dev);
- return mii_nway_restart(&fep->mii_if);
+ return 0;
}
static u32 fs_get_msglevel(struct net_device *dev)
@@ -899,7 +936,7 @@ static int fs_ioctl(struct net_device *d
return -EINVAL;
spin_lock_irqsave(&fep->lock, flags);
- rc = generic_mii_ioctl(&fep->mii_if, mii, cmd, NULL);
+ rc = phy_mii_ioctl(fep->phydev, mii, cmd);
spin_unlock_irqrestore(&fep->lock, flags);
return rc;
}
@@ -1031,12 +1068,6 @@ #endif
}
registered = 1;
- err = fs_mii_connect(ndev);
- if (err != 0) {
- printk(KERN_ERR DRV_MODULE_NAME
- ": %s fs_mii_connect failed.\n", ndev->name);
- goto err;
- }
return ndev;
@@ -1073,8 +1104,6 @@ static int fs_cleanup_instance(struct ne
return -EINVAL;
fpi = fep->fpi;
-
- fs_mii_disconnect(ndev);
unregister_netdev(ndev);
@@ -1197,17 +1226,39 @@ static int __init fs_init(void)
r = setup_immap();
if (r != 0)
return r;
- r = driver_register(&fs_enet_fec_driver);
+
+#ifdef CONFIG_FS_ENET_HAS_FCC
+ /* let's insert mii stuff */
+ r = fs_enet_mdio_bb_init();
+
+ if (r != 0) {
+ printk(KERN_ERR DRV_MODULE_NAME
+ "BB PHY init failed.\n");
+ return r;
+ }
+ r = driver_register(&fs_enet_fcc_driver);
if (r != 0)
goto err;
+#endif
- r = driver_register(&fs_enet_fcc_driver);
+#ifdef CONFIG_FS_ENET_HAS_FEC
+ r = fs_enet_mdio_fec_init();
+ if (r != 0) {
+ printk(KERN_ERR DRV_MODULE_NAME
+ "FEC PHY init failed.\n");
+ return r;
+ }
+
+ r = driver_register(&fs_enet_fec_driver);
if (r != 0)
goto err;
+#endif
+#ifdef CONFIG_FS_ENET_HAS_SCC
r = driver_register(&fs_enet_scc_driver);
if (r != 0)
goto err;
+#endif
return 0;
err:
diff --git a/drivers/net/fs_enet/fs_enet-mii.c b/drivers/net/fs_enet/fs_enet-mii.c
deleted file mode 100644
index c677037..0000000
--- a/drivers/net/fs_enet/fs_enet-mii.c
+++ /dev/null
@@ -1,507 +0,0 @@
-/*
- * Combined Ethernet driver for Motorola MPC8xx and MPC82xx.
- *
- * Copyright (c) 2003 Intracom S.A.
- * by Pantelis Antoniou <panto@intracom.gr>
- *
- * 2005 (c) MontaVista Software, Inc.
- * Vitaly Bordug <vbordug@ru.mvista.com>
- *
- * Heavily based on original FEC driver by Dan Malek <dan@embeddededge.com>
- * and modifications by Joakim Tjernlund <joakim.tjernlund@lumentis.se>
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-
-#include <linux/config.h>
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/sched.h>
-#include <linux/string.h>
-#include <linux/ptrace.h>
-#include <linux/errno.h>
-#include <linux/ioport.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/pci.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/spinlock.h>
-#include <linux/mii.h>
-#include <linux/ethtool.h>
-#include <linux/bitops.h>
-
-#include <asm/pgtable.h>
-#include <asm/irq.h>
-#include <asm/uaccess.h>
-
-#include "fs_enet.h"
-
-/*************************************************/
-
-/*
- * Generic PHY support.
- * Should work for all PHYs, but link change is detected by polling
- */
-
-static void generic_timer_callback(unsigned long data)
-{
- struct net_device *dev = (struct net_device *)data;
- struct fs_enet_private *fep = netdev_priv(dev);
-
- fep->phy_timer_list.expires = jiffies + HZ / 2;
-
- add_timer(&fep->phy_timer_list);
-
- fs_mii_link_status_change_check(dev, 0);
-}
-
-static void generic_startup(struct net_device *dev)
-{
- struct fs_enet_private *fep = netdev_priv(dev);
-
- fep->phy_timer_list.expires = jiffies + HZ / 2; /* every 500ms */
- fep->phy_timer_list.data = (unsigned long)dev;
- fep->phy_timer_list.function = generic_timer_callback;
- add_timer(&fep->phy_timer_list);
-}
-
-static void generic_shutdown(struct net_device *dev)
-{
- struct fs_enet_private *fep = netdev_priv(dev);
-
- del_timer_sync(&fep->phy_timer_list);
-}
-
-/* ------------------------------------------------------------------------- */
-/* The Davicom DM9161 is used on the NETTA board */
-
-/* register definitions */
-
-#define MII_DM9161_ANAR 4 /* Aux. Config Register */
-#define MII_DM9161_ACR 16 /* Aux. Config Register */
-#define MII_DM9161_ACSR 17 /* Aux. Config/Status Register */
-#define MII_DM9161_10TCSR 18 /* 10BaseT Config/Status Reg. */
-#define MII_DM9161_INTR 21 /* Interrupt Register */
-#define MII_DM9161_RECR 22 /* Receive Error Counter Reg. */
-#define MII_DM9161_DISCR 23 /* Disconnect Counter Register */
-
-static void dm9161_startup(struct net_device *dev)
-{
- struct fs_enet_private *fep = netdev_priv(dev);
-
- fs_mii_write(dev, fep->mii_if.phy_id, MII_DM9161_INTR, 0x0000);
- /* Start autonegotiation */
- fs_mii_write(dev, fep->mii_if.phy_id, MII_BMCR, 0x1200);
-
- set_current_state(TASK_UNINTERRUPTIBLE);
- schedule_timeout(HZ*8);
-}
-
-static void dm9161_ack_int(struct net_device *dev)
-{
- struct fs_enet_private *fep = netdev_priv(dev);
-
- fs_mii_read(dev, fep->mii_if.phy_id, MII_DM9161_INTR);
-}
-
-static void dm9161_shutdown(struct net_device *dev)
-{
- struct fs_enet_private *fep = netdev_priv(dev);
-
- fs_mii_write(dev, fep->mii_if.phy_id, MII_DM9161_INTR, 0x0f00);
-}
-
-/**********************************************************************************/
-
-static const struct phy_info phy_info[] = {
- {
- .id = 0x00181b88,
- .name = "DM9161",
- .startup = dm9161_startup,
- .ack_int = dm9161_ack_int,
- .shutdown = dm9161_shutdown,
- }, {
- .id = 0,
- .name = "GENERIC",
- .startup = generic_startup,
- .shutdown = generic_shutdown,
- },
-};
-
-/**********************************************************************************/
-
-static int phy_id_detect(struct net_device *dev)
-{
- struct fs_enet_private *fep = netdev_priv(dev);
- const struct fs_platform_info *fpi = fep->fpi;
- struct fs_enet_mii_bus *bus = fep->mii_bus;
- int i, r, start, end, phytype, physubtype;
- const struct phy_info *phy;
- int phy_hwid, phy_id;
-
- phy_hwid = -1;
- fep->phy = NULL;
-
- /* auto-detect? */
- if (fpi->phy_addr == -1) {
- start = 1;
- end = 32;
- } else { /* direct */
- start = fpi->phy_addr;
- end = start + 1;
- }
-
- for (phy_id = start; phy_id < end; phy_id++) {
- /* skip already used phy addresses on this bus */
- if (bus->usage_map & (1 << phy_id))
- continue;
- r = fs_mii_read(dev, phy_id, MII_PHYSID1);
- if (r == -1 || (phytype = (r & 0xffff)) == 0xffff)
- continue;
- r = fs_mii_read(dev, phy_id, MII_PHYSID2);
- if (r == -1 || (physubtype = (r & 0xffff)) == 0xffff)
- continue;
- phy_hwid = (phytype << 16) | physubtype;
- if (phy_hwid != -1)
- break;
- }
-
- if (phy_hwid == -1) {
- printk(KERN_ERR DRV_MODULE_NAME
- ": %s No PHY detected! range=0x%02x-0x%02x\n",
- dev->name, start, end);
- return -1;
- }
-
- for (i = 0, phy = phy_info; i < ARRAY_SIZE(phy_info); i++, phy++)
- if (phy->id == (phy_hwid >> 4) || phy->id == 0)
- break;
-
- if (i >= ARRAY_SIZE(phy_info)) {
- printk(KERN_ERR DRV_MODULE_NAME
- ": %s PHY id 0x%08x is not supported!\n",
- dev->name, phy_hwid);
- return -1;
- }
-
- fep->phy = phy;
-
- /* mark this address as used */
- bus->usage_map |= (1 << phy_id);
-
- printk(KERN_INFO DRV_MODULE_NAME
- ": %s Phy @ 0x%x, type %s (0x%08x)%s\n",
- dev->name, phy_id, fep->phy->name, phy_hwid,
- fpi->phy_addr == -1 ? " (auto-detected)" : "");
-
- return phy_id;
-}
-
-void fs_mii_startup(struct net_device *dev)
-{
- struct fs_enet_private *fep = netdev_priv(dev);
-
- if (fep->phy->startup)
- (*fep->phy->startup) (dev);
-}
-
-void fs_mii_shutdown(struct net_device *dev)
-{
- struct fs_enet_private *fep = netdev_priv(dev);
-
- if (fep->phy->shutdown)
- (*fep->phy->shutdown) (dev);
-}
-
-void fs_mii_ack_int(struct net_device *dev)
-{
- struct fs_enet_private *fep = netdev_priv(dev);
-
- if (fep->phy->ack_int)
- (*fep->phy->ack_int) (dev);
-}
-
-#define MII_LINK 0x0001
-#define MII_HALF 0x0002
-#define MII_FULL 0x0004
-#define MII_BASE4 0x0008
-#define MII_10M 0x0010
-#define MII_100M 0x0020
-#define MII_1G 0x0040
-#define MII_10G 0x0080
-
-/* return full mii info at one gulp, with a usable form */
-static unsigned int mii_full_status(struct mii_if_info *mii)
-{
- unsigned int status;
- int bmsr, adv, lpa, neg;
- struct fs_enet_private* fep = netdev_priv(mii->dev);
-
- /* first, a dummy read, needed to latch some MII phys */
- (void)mii->mdio_read(mii->dev, mii->phy_id, MII_BMSR);
- bmsr = mii->mdio_read(mii->dev, mii->phy_id, MII_BMSR);
-
- /* no link */
- if ((bmsr & BMSR_LSTATUS) == 0)
- return 0;
-
- status = MII_LINK;
-
- /* Lets look what ANEG says if it's supported - otherwize we shall
- take the right values from the platform info*/
- if(!mii->force_media) {
- /* autoneg not completed; don't bother */
- if ((bmsr & BMSR_ANEGCOMPLETE) == 0)
- return 0;
-
- adv = (*mii->mdio_read)(mii->dev, mii->phy_id, MII_ADVERTISE);
- lpa = (*mii->mdio_read)(mii->dev, mii->phy_id, MII_LPA);
-
- neg = lpa & adv;
- } else {
- neg = fep->fpi->bus_info->lpa;
- }
-
- if (neg & LPA_100FULL)
- status |= MII_FULL | MII_100M;
- else if (neg & LPA_100BASE4)
- status |= MII_FULL | MII_BASE4 | MII_100M;
- else if (neg & LPA_100HALF)
- status |= MII_HALF | MII_100M;
- else if (neg & LPA_10FULL)
- status |= MII_FULL | MII_10M;
- else
- status |= MII_HALF | MII_10M;
-
- return status;
-}
-
-void fs_mii_link_status_change_check(struct net_device *dev, int init_media)
-{
- struct fs_enet_private *fep = netdev_priv(dev);
- struct mii_if_info *mii = &fep->mii_if;
- unsigned int mii_status;
- int ok_to_print, link, duplex, speed;
- unsigned long flags;
-
- ok_to_print = netif_msg_link(fep);
-
- mii_status = mii_full_status(mii);
-
- if (!init_media && mii_status == fep->last_mii_status)
- return;
-
- fep->last_mii_status = mii_status;
-
- link = !!(mii_status & MII_LINK);
- duplex = !!(mii_status & MII_FULL);
- speed = (mii_status & MII_100M) ? 100 : 10;
-
- if (link == 0) {
- netif_carrier_off(mii->dev);
- netif_stop_queue(dev);
- if (!init_media) {
- spin_lock_irqsave(&fep->lock, flags);
- (*fep->ops->stop)(dev);
- spin_unlock_irqrestore(&fep->lock, flags);
- }
-
- if (ok_to_print)
- printk(KERN_INFO "%s: link down\n", mii->dev->name);
-
- } else {
-
- mii->full_duplex = duplex;
-
- netif_carrier_on(mii->dev);
-
- spin_lock_irqsave(&fep->lock, flags);
- fep->duplex = duplex;
- fep->speed = speed;
- (*fep->ops->restart)(dev);
- spin_unlock_irqrestore(&fep->lock, flags);
-
- netif_start_queue(dev);
-
- if (ok_to_print)
- printk(KERN_INFO "%s: link up, %dMbps, %s-duplex\n",
- dev->name, speed, duplex ? "full" : "half");
- }
-}
-
-/**********************************************************************************/
-
-int fs_mii_read(struct net_device *dev, int phy_id, int location)
-{
- struct fs_enet_private *fep = netdev_priv(dev);
- struct fs_enet_mii_bus *bus = fep->mii_bus;
-
- unsigned long flags;
- int ret;
-
- spin_lock_irqsave(&bus->mii_lock, flags);
- ret = (*bus->mii_read)(bus, phy_id, location);
- spin_unlock_irqrestore(&bus->mii_lock, flags);
-
- return ret;
-}
-
-void fs_mii_write(struct net_device *dev, int phy_id, int location, int value)
-{
- struct fs_enet_private *fep = netdev_priv(dev);
- struct fs_enet_mii_bus *bus = fep->mii_bus;
- unsigned long flags;
-
- spin_lock_irqsave(&bus->mii_lock, flags);
- (*bus->mii_write)(bus, phy_id, location, value);
- spin_unlock_irqrestore(&bus->mii_lock, flags);
-}
-
-/*****************************************************************************/
-
-/* list of all registered mii buses */
-static LIST_HEAD(fs_mii_bus_list);
-
-static struct fs_enet_mii_bus *lookup_bus(int method, int id)
-{
- struct list_head *ptr;
- struct fs_enet_mii_bus *bus;
-
- list_for_each(ptr, &fs_mii_bus_list) {
- bus = list_entry(ptr, struct fs_enet_mii_bus, list);
- if (bus->bus_info->method == method &&
- bus->bus_info->id == id)
- return bus;
- }
- return NULL;
-}
-
-static struct fs_enet_mii_bus *create_bus(const struct fs_mii_bus_info *bi)
-{
- struct fs_enet_mii_bus *bus;
- int ret = 0;
-
- bus = kmalloc(sizeof(*bus), GFP_KERNEL);
- if (bus == NULL) {
- ret = -ENOMEM;
- goto err;
- }
- memset(bus, 0, sizeof(*bus));
- spin_lock_init(&bus->mii_lock);
- bus->bus_info = bi;
- bus->refs = 0;
- bus->usage_map = 0;
-
- /* perform initialization */
- switch (bi->method) {
-
- case fsmii_fixed:
- ret = fs_mii_fixed_init(bus);
- if (ret != 0)
- goto err;
- break;
-
- case fsmii_bitbang:
- ret = fs_mii_bitbang_init(bus);
- if (ret != 0)
- goto err;
- break;
-#ifdef CONFIG_FS_ENET_HAS_FEC
- case fsmii_fec:
- ret = fs_mii_fec_init(bus);
- if (ret != 0)
- goto err;
- break;
-#endif
- default:
- ret = -EINVAL;
- goto err;
- }
-
- list_add(&bus->list, &fs_mii_bus_list);
-
- return bus;
-
-err:
- if (bus)
- kfree(bus);
- return ERR_PTR(ret);
-}
-
-static void destroy_bus(struct fs_enet_mii_bus *bus)
-{
- /* remove from bus list */
- list_del(&bus->list);
-
- /* nothing more needed */
- kfree(bus);
-}
-
-int fs_mii_connect(struct net_device *dev)
-{
- struct fs_enet_private *fep = netdev_priv(dev);
- const struct fs_platform_info *fpi = fep->fpi;
- struct fs_enet_mii_bus *bus = NULL;
-
- /* check method validity */
- switch (fpi->bus_info->method) {
- case fsmii_fixed:
- case fsmii_bitbang:
- break;
-#ifdef CONFIG_FS_ENET_HAS_FEC
- case fsmii_fec:
- break;
-#endif
- default:
- printk(KERN_ERR DRV_MODULE_NAME
- ": %s Unknown MII bus method (%d)!\n",
- dev->name, fpi->bus_info->method);
- return -EINVAL;
- }
-
- bus = lookup_bus(fpi->bus_info->method, fpi->bus_info->id);
-
- /* if not found create new bus */
- if (bus == NULL) {
- bus = create_bus(fpi->bus_info);
- if (IS_ERR(bus)) {
- printk(KERN_ERR DRV_MODULE_NAME
- ": %s MII bus creation failure!\n", dev->name);
- return PTR_ERR(bus);
- }
- }
-
- bus->refs++;
-
- fep->mii_bus = bus;
-
- fep->mii_if.dev = dev;
- fep->mii_if.phy_id_mask = 0x1f;
- fep->mii_if.reg_num_mask = 0x1f;
- fep->mii_if.mdio_read = fs_mii_read;
- fep->mii_if.mdio_write = fs_mii_write;
- fep->mii_if.force_media = fpi->bus_info->disable_aneg;
- fep->mii_if.phy_id = phy_id_detect(dev);
-
- return 0;
-}
-
-void fs_mii_disconnect(struct net_device *dev)
-{
- struct fs_enet_private *fep = netdev_priv(dev);
- struct fs_enet_mii_bus *bus = NULL;
-
- bus = fep->mii_bus;
- fep->mii_bus = NULL;
-
- if (--bus->refs <= 0)
- destroy_bus(bus);
-}
diff --git a/drivers/net/fs_enet/fs_enet.h b/drivers/net/fs_enet/fs_enet.h
index e7ec96c..95022c0 100644
--- a/drivers/net/fs_enet/fs_enet.h
+++ b/drivers/net/fs_enet/fs_enet.h
@@ -5,6 +5,7 @@ #include <linux/mii.h>
#include <linux/netdevice.h>
#include <linux/types.h>
#include <linux/list.h>
+#include <linux/phy.h>
#include <linux/fs_enet_pd.h>
@@ -12,11 +13,29 @@ #include <asm/dma-mapping.h>
#ifdef CONFIG_CPM1
#include <asm/commproc.h>
+
+struct fec_info {
+ fec_t* fecp;
+ u32 mii_speed;
+};
#endif
#ifdef CONFIG_CPM2
#include <asm/cpm2.h>
#endif
+
+/* This is used to operate with pins.
+ Note that the actual port size may
+ be different; cpm(s) handle it OK */
+struct bb_info {
+ u8 mdio_dat_msk;
+ u8 mdio_dir_msk;
+ u8 *mdio_dir;
+ u8 *mdio_dat;
+ u8 mdc_msk;
+ u8 *mdc_dat;
+ int delay;
+};
/* hw driver ops */
struct fs_ops {
@@ -25,6 +44,7 @@ struct fs_ops {
void (*free_bd)(struct net_device *dev);
void (*cleanup_data)(struct net_device *dev);
void (*set_multicast_list)(struct net_device *dev);
+ void (*adjust_link)(struct net_device *dev);
void (*restart)(struct net_device *dev);
void (*stop)(struct net_device *dev);
void (*pre_request_irq)(struct net_device *dev, int irq);
@@ -99,10 +119,6 @@ struct fs_enet_mii_bus {
} fixed;
};
};
-
-int fs_mii_bitbang_init(struct fs_enet_mii_bus *bus);
-int fs_mii_fixed_init(struct fs_enet_mii_bus *bus);
-int fs_mii_fec_init(struct fs_enet_mii_bus *bus);
struct fs_enet_private {
struct device *dev; /* pointer back to the device (must be initialized first) */
@@ -130,7 +146,8 @@ struct fs_enet_private {
struct fs_enet_mii_bus *mii_bus;
int interrupt;
- int duplex, speed; /* current settings */
+ struct phy_device *phydev;
+ int oldduplex, oldspeed, oldlink; /* current settings */
/* event masks */
u32 ev_napi_rx; /* mask of NAPI rx events */
@@ -168,15 +185,9 @@ struct fs_enet_private {
};
/***************************************************************************/
-
-int fs_mii_read(struct net_device *dev, int phy_id, int location);
-void fs_mii_write(struct net_device *dev, int phy_id, int location, int value);
-
-void fs_mii_startup(struct net_device *dev);
-void fs_mii_shutdown(struct net_device *dev);
-void fs_mii_ack_int(struct net_device *dev);
-
-void fs_mii_link_status_change_check(struct net_device *dev, int init_media);
+int fs_enet_mdio_bb_init(void);
+int fs_mii_fixed_init(struct fs_enet_mii_bus *bus);
+int fs_enet_mdio_fec_init(void);
void fs_init_bds(struct net_device *dev);
void fs_cleanup_bds(struct net_device *dev);
@@ -194,7 +205,6 @@ int fs_enet_platform_init(void);
void fs_enet_platform_cleanup(void);
/***************************************************************************/
-
/* buffer descriptor access macros */
/* access macros */
diff --git a/drivers/net/fs_enet/mac-fcc.c b/drivers/net/fs_enet/mac-fcc.c
index 95e2bb8..8bc711d 100644
--- a/drivers/net/fs_enet/mac-fcc.c
+++ b/drivers/net/fs_enet/mac-fcc.c
@@ -35,6 +35,7 @@ #include <linux/ethtool.h>
#include <linux/bitops.h>
#include <linux/fs.h>
#include <linux/platform_device.h>
+#include <linux/phy.h>
#include <asm/immap_cpm2.h>
#include <asm/mpc8260.h>
@@ -123,20 +124,30 @@ static int do_pd_setup(struct fs_enet_pr
/* Attach the memory for the FCC Parameter RAM */
r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "fcc_pram");
- fep->fcc.ep = (void *)r->start;
-
+ fep->fcc.ep = (void *)ioremap(r->start, r->end - r->start + 1);
if (fep->fcc.ep == NULL)
return -EINVAL;
r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "fcc_regs");
- fep->fcc.fccp = (void *)r->start;
-
+ fep->fcc.fccp = (void *)ioremap(r->start, r->end - r->start + 1);
if (fep->fcc.fccp == NULL)
return -EINVAL;
+
+ if (fep->fpi->fcc_regs_c) {
- fep->fcc.fcccp = (void *)fep->fpi->fcc_regs_c;
+ fep->fcc.fcccp = (void *)fep->fpi->fcc_regs_c;
+ } else {
+ r = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+ "fcc_regs_c");
+ fep->fcc.fcccp = (void *)ioremap(r->start,
+ r->end - r->start + 1);
+ }
if (fep->fcc.fcccp == NULL)
+ return -EINVAL;
+
+ fep->fcc.mem = (void *)fep->fpi->mem_offset;
+ if (fep->fcc.mem == NULL)
return -EINVAL;
return 0;
@@ -156,8 +167,6 @@ static int setup_data(struct net_device
if ((unsigned int)fep->fcc.idx >= 3) /* max 3 FCCs */
return -EINVAL;
- fep->fcc.mem = (void *)fpi->mem_offset;
-
if (do_pd_setup(fep) != 0)
return -EINVAL;
@@ -395,7 +404,7 @@ static void restart(struct net_device *d
/* adjust to speed (for RMII mode) */
if (fpi->use_rmii) {
- if (fep->speed == 100)
+ if (fep->phydev->speed == 100)
C8(fcccp, fcc_gfemr, 0x20);
else
S8(fcccp, fcc_gfemr, 0x20);
@@ -421,7 +430,7 @@ static void restart(struct net_device *d
S32(fccp, fcc_fpsmr, FCC_PSMR_RMII);
/* adjust to duplex mode */
- if (fep->duplex)
+ if (fep->phydev->duplex)
S32(fccp, fcc_fpsmr, FCC_PSMR_FDE | FCC_PSMR_LPB);
else
C32(fccp, fcc_fpsmr, FCC_PSMR_FDE | FCC_PSMR_LPB);
@@ -487,7 +496,10 @@ static void rx_bd_done(struct net_device
static void tx_kickstart(struct net_device *dev)
{
- /* nothing */
+ struct fs_enet_private *fep = netdev_priv(dev);
+ fcc_t *fccp = fep->fcc.fccp;
+
+ S32(fccp, fcc_ftodr, 0x80);
}
static u32 get_int_events(struct net_device *dev)
diff --git a/drivers/net/fs_enet/mac-fec.c b/drivers/net/fs_enet/mac-fec.c
index 3dad69d..99678c3 100644
--- a/drivers/net/fs_enet/mac-fec.c
+++ b/drivers/net/fs_enet/mac-fec.c
@@ -47,6 +47,7 @@ #include <asm/commproc.h>
#endif
#include "fs_enet.h"
+#include "fec.h"
/*************************************************/
@@ -76,48 +77,6 @@ #define FS(_fecp, _reg, _v) FW(_fecp, _r
/* clear bits */
#define FC(_fecp, _reg, _v) FW(_fecp, _reg, FR(_fecp, _reg) & ~(_v))
-
-/* CRC polynomium used by the FEC for the multicast group filtering */
-#define FEC_CRC_POLY 0x04C11DB7
-
-#define FEC_MAX_MULTICAST_ADDRS 64
-
-/* Interrupt events/masks.
-*/
-#define FEC_ENET_HBERR 0x80000000U /* Heartbeat error */
-#define FEC_ENET_BABR 0x40000000U /* Babbling receiver */
-#define FEC_ENET_BABT 0x20000000U /* Babbling transmitter */
-#define FEC_ENET_GRA 0x10000000U /* Graceful stop complete */
-#define FEC_ENET_TXF 0x08000000U /* Full frame transmitted */
-#define FEC_ENET_TXB 0x04000000U /* A buffer was transmitted */
-#define FEC_ENET_RXF 0x02000000U /* Full frame received */
-#define FEC_ENET_RXB 0x01000000U /* A buffer was received */
-#define FEC_ENET_MII 0x00800000U /* MII interrupt */
-#define FEC_ENET_EBERR 0x00400000U /* SDMA bus error */
-
-#define FEC_ECNTRL_PINMUX 0x00000004
-#define FEC_ECNTRL_ETHER_EN 0x00000002
-#define FEC_ECNTRL_RESET 0x00000001
-
-#define FEC_RCNTRL_BC_REJ 0x00000010
-#define FEC_RCNTRL_PROM 0x00000008
-#define FEC_RCNTRL_MII_MODE 0x00000004
-#define FEC_RCNTRL_DRT 0x00000002
-#define FEC_RCNTRL_LOOP 0x00000001
-
-#define FEC_TCNTRL_FDEN 0x00000004
-#define FEC_TCNTRL_HBC 0x00000002
-#define FEC_TCNTRL_GTS 0x00000001
-
-
-/* Make MII read/write commands for the FEC.
-*/
-#define mk_mii_read(REG) (0x60020000 | ((REG & 0x1f) << 18))
-#define mk_mii_write(REG, VAL) (0x50020000 | ((REG & 0x1f) << 18) | (VAL & 0xffff))
-#define mk_mii_end 0
-
-#define FEC_MII_LOOPS 10000
-
/*
* Delay to wait for FEC reset command to complete (in us)
*/
@@ -303,12 +262,14 @@ #endif
dma_addr_t rx_bd_base_phys, tx_bd_base_phys;
int r;
u32 addrhi, addrlo;
+
+ struct mii_bus* mii = fep->phydev->bus;
+ struct fec_info* fec_inf = mii->priv;
r = whack_reset(fep->fec.fecp);
if (r != 0)
printk(KERN_ERR DRV_MODULE_NAME
": %s FEC Reset FAILED!\n", dev->name);
-
/*
* Set station address.
*/
@@ -353,7 +314,7 @@ #endif
/*
* Set MII speed.
*/
- FW(fecp, mii_speed, fep->mii_bus->fec.mii_speed);
+ FW(fecp, mii_speed, fec_inf->mii_speed);
/*
* Clear any outstanding interrupt.
@@ -391,11 +352,12 @@ #ifdef CONFIG_DUET
}
#endif
+
FW(fecp, r_cntrl, FEC_RCNTRL_MII_MODE); /* MII enable */
/*
* adjust to duplex mode
*/
- if (fep->duplex) {
+ if (fep->phydev->duplex) {
FC(fecp, r_cntrl, FEC_RCNTRL_DRT);
FS(fecp, x_cntrl, FEC_TCNTRL_FDEN); /* FD enable */
} else {
@@ -419,9 +381,11 @@ #endif
static void stop(struct net_device *dev)
{
struct fs_enet_private *fep = netdev_priv(dev);
+ const struct fs_platform_info *fpi = fep->fpi;
fec_t *fecp = fep->fec.fecp;
- struct fs_enet_mii_bus *bus = fep->mii_bus;
- const struct fs_mii_bus_info *bi = bus->bus_info;
+
+ struct fec_info* feci= fep->phydev->bus->priv;
+
int i;
if ((FR(fecp, ecntrl) & FEC_ECNTRL_ETHER_EN) == 0)
@@ -445,11 +409,11 @@ static void stop(struct net_device *dev)
fs_cleanup_bds(dev);
/* shut down FEC1? that's where the mii bus is */
- if (fep->fec.idx == 0 && bus->refs > 1 && bi->method == fsmii_fec) {
+ if (fpi->has_phy) {
FS(fecp, r_cntrl, FEC_RCNTRL_MII_MODE); /* MII enable */
FS(fecp, ecntrl, FEC_ECNTRL_PINMUX | FEC_ECNTRL_ETHER_EN);
FW(fecp, ievent, FEC_ENET_MII);
- FW(fecp, mii_speed, bus->fec.mii_speed);
+ FW(fecp, mii_speed, feci->mii_speed);
}
}
@@ -583,74 +547,4 @@ const struct fs_ops fs_fec_ops = {
.allocate_bd = allocate_bd,
.free_bd = free_bd,
};
-
-/***********************************************************************/
-
-static int mii_read(struct fs_enet_mii_bus *bus, int phy_id, int location)
-{
- fec_t *fecp = bus->fec.fecp;
- int i, ret = -1;
-
- if ((FR(fecp, r_cntrl) & FEC_RCNTRL_MII_MODE) == 0)
- BUG();
-
- /* Add PHY address to register command. */
- FW(fecp, mii_data, (phy_id << 23) | mk_mii_read(location));
- for (i = 0; i < FEC_MII_LOOPS; i++)
- if ((FR(fecp, ievent) & FEC_ENET_MII) != 0)
- break;
-
- if (i < FEC_MII_LOOPS) {
- FW(fecp, ievent, FEC_ENET_MII);
- ret = FR(fecp, mii_data) & 0xffff;
- }
-
- return ret;
-}
-
-static void mii_write(struct fs_enet_mii_bus *bus, int phy_id, int location, int value)
-{
- fec_t *fecp = bus->fec.fecp;
- int i;
-
- /* this must never happen */
- if ((FR(fecp, r_cntrl) & FEC_RCNTRL_MII_MODE) == 0)
- BUG();
-
- /* Add PHY address to register command. */
- FW(fecp, mii_data, (phy_id << 23) | mk_mii_write(location, value));
-
- for (i = 0; i < FEC_MII_LOOPS; i++)
- if ((FR(fecp, ievent) & FEC_ENET_MII) != 0)
- break;
-
- if (i < FEC_MII_LOOPS)
- FW(fecp, ievent, FEC_ENET_MII);
-}
-
-int fs_mii_fec_init(struct fs_enet_mii_bus *bus)
-{
- bd_t *bd = (bd_t *)__res;
- const struct fs_mii_bus_info *bi = bus->bus_info;
- fec_t *fecp;
-
- if (bi->id != 0)
- return -1;
-
- bus->fec.fecp = &((immap_t *)fs_enet_immap)->im_cpm.cp_fec;
- bus->fec.mii_speed = ((((bd->bi_intfreq + 4999999) / 2500000) / 2)
- & 0x3F) << 1;
-
- fecp = bus->fec.fecp;
-
- FS(fecp, r_cntrl, FEC_RCNTRL_MII_MODE); /* MII enable */
- FS(fecp, ecntrl, FEC_ECNTRL_PINMUX | FEC_ECNTRL_ETHER_EN);
- FW(fecp, ievent, FEC_ENET_MII);
- FW(fecp, mii_speed, bus->fec.mii_speed);
-
- bus->mii_read = mii_read;
- bus->mii_write = mii_write;
-
- return 0;
-}
diff --git a/drivers/net/fs_enet/mac-scc.c b/drivers/net/fs_enet/mac-scc.c
index a772b28..d829120 100644
--- a/drivers/net/fs_enet/mac-scc.c
+++ b/drivers/net/fs_enet/mac-scc.c
@@ -370,7 +370,7 @@ static void restart(struct net_device *d
W16(sccp, scc_psmr, SCC_PSMR_ENCRC | SCC_PSMR_NIB22);
/* Set full duplex mode if needed */
- if (fep->duplex)
+ if (fep->phydev->duplex)
S16(sccp, scc_psmr, SCC_PSMR_LPB | SCC_PSMR_FDE);
S32(sccp, scc_gsmrl, SCC_GSMRL_ENR | SCC_GSMRL_ENT);
@@ -500,6 +500,8 @@ static void tx_restart(struct net_device
scc_cr_cmd(fep, CPM_CR_RESTART_TX);
}
+
+
/*************************************************************************/
diff --git a/drivers/net/fs_enet/mii-bitbang.c b/drivers/net/fs_enet/mii-bitbang.c
index 24a5e2e..cf2955f 100644
--- a/drivers/net/fs_enet/mii-bitbang.c
+++ b/drivers/net/fs_enet/mii-bitbang.c
@@ -34,6 +34,7 @@ #include <linux/spinlock.h>
#include <linux/mii.h>
#include <linux/ethtool.h>
#include <linux/bitops.h>
+#include <linux/platform_device.h>
#include <asm/pgtable.h>
#include <asm/irq.h>
@@ -41,129 +42,25 @@ #include <asm/uaccess.h>
#include "fs_enet.h"
-#ifdef CONFIG_8xx
-static int bitbang_prep_bit(u8 **dirp, u8 **datp, u8 *mskp, int port, int bit)
+static int bitbang_prep_bit(u8 **datp, u8 *mskp,
+ struct fs_mii_bit *mii_bit)
{
- immap_t *im = (immap_t *)fs_enet_immap;
- void *dir, *dat, *ppar;
+ void *dat;
int adv;
u8 msk;
-
- switch (port) {
- case fsiop_porta:
- dir = &im->im_ioport.iop_padir;
- dat = &im->im_ioport.iop_padat;
- ppar = &im->im_ioport.iop_papar;
- break;
-
- case fsiop_portb:
- dir = &im->im_cpm.cp_pbdir;
- dat = &im->im_cpm.cp_pbdat;
- ppar = &im->im_cpm.cp_pbpar;
- break;
-
- case fsiop_portc:
- dir = &im->im_ioport.iop_pcdir;
- dat = &im->im_ioport.iop_pcdat;
- ppar = &im->im_ioport.iop_pcpar;
- break;
-
- case fsiop_portd:
- dir = &im->im_ioport.iop_pddir;
- dat = &im->im_ioport.iop_pddat;
- ppar = &im->im_ioport.iop_pdpar;
- break;
-
- case fsiop_porte:
- dir = &im->im_cpm.cp_pedir;
- dat = &im->im_cpm.cp_pedat;
- ppar = &im->im_cpm.cp_pepar;
- break;
-
- default:
- printk(KERN_ERR DRV_MODULE_NAME
- "Illegal port value %d!\n", port);
- return -EINVAL;
- }
-
- adv = bit >> 3;
- dir = (char *)dir + adv;
- dat = (char *)dat + adv;
- ppar = (char *)ppar + adv;
-
- msk = 1 << (7 - (bit & 7));
- if ((in_8(ppar) & msk) != 0) {
- printk(KERN_ERR DRV_MODULE_NAME
- "pin %d on port %d is not general purpose!\n", bit, port);
- return -EINVAL;
- }
- *dirp = dir;
- *datp = dat;
- *mskp = msk;
+ dat = (void*) mii_bit->offset;
- return 0;
-}
-#endif
-
-#ifdef CONFIG_8260
-static int bitbang_prep_bit(u8 **dirp, u8 **datp, u8 *mskp, int port, int bit)
-{
- iop_cpm2_t *io = &((cpm2_map_t *)fs_enet_immap)->im_ioport;
- void *dir, *dat, *ppar;
- int adv;
- u8 msk;
-
- switch (port) {
- case fsiop_porta:
- dir = &io->iop_pdira;
- dat = &io->iop_pdata;
- ppar = &io->iop_ppara;
- break;
-
- case fsiop_portb:
- dir = &io->iop_pdirb;
- dat = &io->iop_pdatb;
- ppar = &io->iop_pparb;
- break;
-
- case fsiop_portc:
- dir = &io->iop_pdirc;
- dat = &io->iop_pdatc;
- ppar = &io->iop_pparc;
- break;
-
- case fsiop_portd:
- dir = &io->iop_pdird;
- dat = &io->iop_pdatd;
- ppar = &io->iop_ppard;
- break;
-
- default:
- printk(KERN_ERR DRV_MODULE_NAME
- "Illegal port value %d!\n", port);
- return -EINVAL;
- }
-
- adv = bit >> 3;
- dir = (char *)dir + adv;
+ adv = mii_bit->bit >> 3;
dat = (char *)dat + adv;
- ppar = (char *)ppar + adv;
-
- msk = 1 << (7 - (bit & 7));
- if ((in_8(ppar) & msk) != 0) {
- printk(KERN_ERR DRV_MODULE_NAME
- "pin %d on port %d is not general purpose!\n", bit, port);
- return -EINVAL;
- }
- *dirp = dir;
+ msk = 1 << (7 - (mii_bit->bit & 7));
+
*datp = dat;
*mskp = msk;
return 0;
}
-#endif
static inline void bb_set(u8 *p, u8 m)
{
@@ -180,44 +77,44 @@ static inline int bb_read(u8 *p, u8 m)
return (in_8(p) & m) != 0;
}
-static inline void mdio_active(struct fs_enet_mii_bus *bus)
+static inline void mdio_active(struct bb_info *bitbang)
{
- bb_set(bus->bitbang.mdio_dir, bus->bitbang.mdio_msk);
+ bb_set(bitbang->mdio_dir, bitbang->mdio_dir_msk);
}
-static inline void mdio_tristate(struct fs_enet_mii_bus *bus)
+static inline void mdio_tristate(struct bb_info *bitbang )
{
- bb_clr(bus->bitbang.mdio_dir, bus->bitbang.mdio_msk);
+ bb_clr(bitbang->mdio_dir, bitbang->mdio_dir_msk);
}
-static inline int mdio_read(struct fs_enet_mii_bus *bus)
+static inline int mdio_read(struct bb_info *bitbang )
{
- return bb_read(bus->bitbang.mdio_dat, bus->bitbang.mdio_msk);
+ return bb_read(bitbang->mdio_dat, bitbang->mdio_dat_msk);
}
-static inline void mdio(struct fs_enet_mii_bus *bus, int what)
+static inline void mdio(struct bb_info *bitbang , int what)
{
if (what)
- bb_set(bus->bitbang.mdio_dat, bus->bitbang.mdio_msk);
+ bb_set(bitbang->mdio_dat, bitbang->mdio_dat_msk);
else
- bb_clr(bus->bitbang.mdio_dat, bus->bitbang.mdio_msk);
+ bb_clr(bitbang->mdio_dat, bitbang->mdio_dat_msk);
}
-static inline void mdc(struct fs_enet_mii_bus *bus, int what)
+static inline void mdc(struct bb_info *bitbang , int what)
{
if (what)
- bb_set(bus->bitbang.mdc_dat, bus->bitbang.mdc_msk);
+ bb_set(bitbang->mdc_dat, bitbang->mdc_msk);
else
- bb_clr(bus->bitbang.mdc_dat, bus->bitbang.mdc_msk);
+ bb_clr(bitbang->mdc_dat, bitbang->mdc_msk);
}
-static inline void mii_delay(struct fs_enet_mii_bus *bus)
+static inline void mii_delay(struct bb_info *bitbang )
{
- udelay(bus->bus_info->i.bitbang.delay);
+ udelay(bitbang->delay);
}
/* Utility to send the preamble, address, and register (common to read and write). */
-static void bitbang_pre(struct fs_enet_mii_bus *bus, int read, u8 addr, u8 reg)
+static void bitbang_pre(struct bb_info *bitbang , int read, u8 addr, u8 reg)
{
int j;
@@ -229,177 +126,284 @@ static void bitbang_pre(struct fs_enet_m
* but it is safer and will be much more robust.
*/
- mdio_active(bus);
- mdio(bus, 1);
+ mdio_active(bitbang);
+ mdio(bitbang, 1);
for (j = 0; j < 32; j++) {
- mdc(bus, 0);
- mii_delay(bus);
- mdc(bus, 1);
- mii_delay(bus);
+ mdc(bitbang, 0);
+ mii_delay(bitbang);
+ mdc(bitbang, 1);
+ mii_delay(bitbang);
}
/* send the start bit (01) and the read opcode (10) or write (10) */
- mdc(bus, 0);
- mdio(bus, 0);
- mii_delay(bus);
- mdc(bus, 1);
- mii_delay(bus);
- mdc(bus, 0);
- mdio(bus, 1);
- mii_delay(bus);
- mdc(bus, 1);
- mii_delay(bus);
- mdc(bus, 0);
- mdio(bus, read);
- mii_delay(bus);
- mdc(bus, 1);
- mii_delay(bus);
- mdc(bus, 0);
- mdio(bus, !read);
- mii_delay(bus);
- mdc(bus, 1);
- mii_delay(bus);
-
+ mdc(bitbang, 0);
+ mdio(bitbang, 0);
+ mii_delay(bitbang);
+ mdc(bitbang, 1);
+ mii_delay(bitbang);
+ mdc(bitbang, 0);
+ mdio(bitbang, 1);
+ mii_delay(bitbang);
+ mdc(bitbang, 1);
+ mii_delay(bitbang);
+ mdc(bitbang, 0);
+ mdio(bitbang, read);
+ mii_delay(bitbang);
+ mdc(bitbang, 1);
+ mii_delay(bitbang);
+ mdc(bitbang, 0);
+ mdio(bitbang, !read);
+ mii_delay(bitbang);
+ mdc(bitbang, 1);
+ mii_delay(bitbang);
+
/* send the PHY address */
- for (j = 0; j < 5; j++) {
- mdc(bus, 0);
- mdio(bus, (addr & 0x10) != 0);
- mii_delay(bus);
- mdc(bus, 1);
- mii_delay(bus);
+ for (j = 0; j < 5; j++) {
+ mdc(bitbang, 0);
+ mdio(bitbang, (addr & 0x10) != 0);
+ mii_delay(bitbang);
+ mdc(bitbang, 1);
+ mii_delay(bitbang);
addr <<= 1;
}
/* send the register address */
- for (j = 0; j < 5; j++) {
- mdc(bus, 0);
- mdio(bus, (reg & 0x10) != 0);
- mii_delay(bus);
- mdc(bus, 1);
- mii_delay(bus);
+ for (j = 0; j < 5; j++) {
+ mdc(bitbang, 0);
+ mdio(bitbang, (reg & 0x10) != 0);
+ mii_delay(bitbang);
+ mdc(bitbang, 1);
+ mii_delay(bitbang);
reg <<= 1;
}
}
-static int mii_read(struct fs_enet_mii_bus *bus, int phy_id, int location)
+static int fs_enet_mii_bb_read(struct mii_bus *bus , int phy_id, int location)
{
u16 rdreg;
int ret, j;
u8 addr = phy_id & 0xff;
u8 reg = location & 0xff;
+ struct bb_info* bitbang = bus->priv;
- bitbang_pre(bus, 1, addr, reg);
+ bitbang_pre(bitbang, 1, addr, reg);
/* tri-state our MDIO I/O pin so we can read */
- mdc(bus, 0);
- mdio_tristate(bus);
- mii_delay(bus);
- mdc(bus, 1);
- mii_delay(bus);
-
+ mdc(bitbang, 0);
+ mdio_tristate(bitbang);
+ mii_delay(bitbang);
+ mdc(bitbang, 1);
+ mii_delay(bitbang);
+
/* check the turnaround bit: the PHY should be driving it to zero */
- if (mdio_read(bus) != 0) {
+ if (mdio_read(bitbang) != 0) {
/* PHY didn't drive TA low */
for (j = 0; j < 32; j++) {
- mdc(bus, 0);
- mii_delay(bus);
- mdc(bus, 1);
- mii_delay(bus);
+ mdc(bitbang, 0);
+ mii_delay(bitbang);
+ mdc(bitbang, 1);
+ mii_delay(bitbang);
}
ret = -1;
goto out;
}
- mdc(bus, 0);
- mii_delay(bus);
+ mdc(bitbang, 0);
+ mii_delay(bitbang);
/* read 16 bits of register data, MSB first */
rdreg = 0;
for (j = 0; j < 16; j++) {
- mdc(bus, 1);
- mii_delay(bus);
+ mdc(bitbang, 1);
+ mii_delay(bitbang);
rdreg <<= 1;
- rdreg |= mdio_read(bus);
- mdc(bus, 0);
- mii_delay(bus);
+ rdreg |= mdio_read(bitbang);
+ mdc(bitbang, 0);
+ mii_delay(bitbang);
}
- mdc(bus, 1);
- mii_delay(bus);
- mdc(bus, 0);
- mii_delay(bus);
- mdc(bus, 1);
- mii_delay(bus);
+ mdc(bitbang, 1);
+ mii_delay(bitbang);
+ mdc(bitbang, 0);
+ mii_delay(bitbang);
+ mdc(bitbang, 1);
+ mii_delay(bitbang);
ret = rdreg;
out:
return ret;
}
-static void mii_write(struct fs_enet_mii_bus *bus, int phy_id, int location, int val)
+static int fs_enet_mii_bb_write(struct mii_bus *bus, int phy_id, int location, u16 val)
{
int j;
+ struct bb_info* bitbang = bus->priv;
+
u8 addr = phy_id & 0xff;
u8 reg = location & 0xff;
u16 value = val & 0xffff;
- bitbang_pre(bus, 0, addr, reg);
+ bitbang_pre(bitbang, 0, addr, reg);
/* send the turnaround (10) */
- mdc(bus, 0);
- mdio(bus, 1);
- mii_delay(bus);
- mdc(bus, 1);
- mii_delay(bus);
- mdc(bus, 0);
- mdio(bus, 0);
- mii_delay(bus);
- mdc(bus, 1);
- mii_delay(bus);
-
+ mdc(bitbang, 0);
+ mdio(bitbang, 1);
+ mii_delay(bitbang);
+ mdc(bitbang, 1);
+ mii_delay(bitbang);
+ mdc(bitbang, 0);
+ mdio(bitbang, 0);
+ mii_delay(bitbang);
+ mdc(bitbang, 1);
+ mii_delay(bitbang);
+
/* write 16 bits of register data, MSB first */
- for (j = 0; j < 16; j++) {
- mdc(bus, 0);
- mdio(bus, (value & 0x8000) != 0);
- mii_delay(bus);
- mdc(bus, 1);
- mii_delay(bus);
+ for (j = 0; j < 16; j++) {
+ mdc(bitbang, 0);
+ mdio(bitbang, (value & 0x8000) != 0);
+ mii_delay(bitbang);
+ mdc(bitbang, 1);
+ mii_delay(bitbang);
value <<= 1;
}
/*
* Tri-state the MDIO line.
*/
- mdio_tristate(bus);
- mdc(bus, 0);
- mii_delay(bus);
- mdc(bus, 1);
- mii_delay(bus);
+ mdio_tristate(bitbang);
+ mdc(bitbang, 0);
+ mii_delay(bitbang);
+ mdc(bitbang, 1);
+ mii_delay(bitbang);
+ return 0;
}
-int fs_mii_bitbang_init(struct fs_enet_mii_bus *bus)
+static int fs_enet_mii_bb_reset(struct mii_bus *bus)
{
- const struct fs_mii_bus_info *bi = bus->bus_info;
+ /*nothing here - dunno how to reset it*/
+ return 0;
+}
+
+static int fs_mii_bitbang_init(struct bb_info *bitbang, struct fs_mii_bb_platform_info* fmpi)
+{
int r;
+
+ bitbang->delay = fmpi->delay;
- r = bitbang_prep_bit(&bus->bitbang.mdio_dir,
- &bus->bitbang.mdio_dat,
- &bus->bitbang.mdio_msk,
- bi->i.bitbang.mdio_port,
- bi->i.bitbang.mdio_bit);
+ r = bitbang_prep_bit(&bitbang->mdio_dir,
+ &bitbang->mdio_dir_msk,
+ &fmpi->mdio_dir);
if (r != 0)
return r;
- r = bitbang_prep_bit(&bus->bitbang.mdc_dir,
- &bus->bitbang.mdc_dat,
- &bus->bitbang.mdc_msk,
- bi->i.bitbang.mdc_port,
- bi->i.bitbang.mdc_bit);
+ r = bitbang_prep_bit(&bitbang->mdio_dat,
+ &bitbang->mdio_dat_msk,
+ &fmpi->mdio_dat);
if (r != 0)
return r;
- bus->mii_read = mii_read;
- bus->mii_write = mii_write;
+ r = bitbang_prep_bit(&bitbang->mdc_dat,
+ &bitbang->mdc_msk,
+ &fmpi->mdc_dat);
+ if (r != 0)
+ return r;
return 0;
}
+
+
+static int __devinit fs_enet_mdio_probe(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct fs_mii_bb_platform_info *pdata;
+ struct mii_bus *new_bus;
+ struct bb_info *bitbang;
+ int err = 0;
+
+ if (NULL == dev)
+ return -EINVAL;
+
+ new_bus = kzalloc(sizeof(struct mii_bus), GFP_KERNEL);
+
+ if (NULL == new_bus)
+ return -ENOMEM;
+
+ bitbang = kzalloc(sizeof(struct bb_info), GFP_KERNEL);
+
+ if (NULL == bitbang)
+ return -ENOMEM;
+
+ new_bus->name = "BB MII Bus",
+ new_bus->read = &fs_enet_mii_bb_read,
+ new_bus->write = &fs_enet_mii_bb_write,
+ new_bus->reset = &fs_enet_mii_bb_reset,
+ new_bus->id = pdev->id;
+
+ new_bus->phy_mask = ~0x9;
+ pdata = (struct fs_mii_bb_platform_info *)pdev->dev.platform_data;
+
+ if (NULL == pdata) {
+ printk(KERN_ERR "gfar mdio %d: Missing platform data!\n", pdev->id);
+ return -ENODEV;
+ }
+
+ /*set up workspace*/
+ fs_mii_bitbang_init(bitbang, pdata);
+
+ new_bus->priv = bitbang;
+
+ new_bus->irq = pdata->irq;
+
+ new_bus->dev = dev;
+ dev_set_drvdata(dev, new_bus);
+
+ err = mdiobus_register(new_bus);
+
+ if (0 != err) {
+ printk (KERN_ERR "%s: Cannot register as MDIO bus\n",
+ new_bus->name);
+ goto bus_register_fail;
+ }
+
+ return 0;
+
+bus_register_fail:
+ kfree(bitbang);
+ kfree(new_bus);
+
+ return err;
+}
+
+
+static int fs_enet_mdio_remove(struct device *dev)
+{
+ struct mii_bus *bus = dev_get_drvdata(dev);
+
+ mdiobus_unregister(bus);
+
+ dev_set_drvdata(dev, NULL);
+
+ iounmap((void *) (&bus->priv));
+ bus->priv = NULL;
+ kfree(bus);
+
+ return 0;
+}
+
+static struct device_driver fs_enet_bb_mdio_driver = {
+ .name = "fsl-bb-mdio",
+ .bus = &platform_bus_type,
+ .probe = fs_enet_mdio_probe,
+ .remove = fs_enet_mdio_remove,
+};
+
+int fs_enet_mdio_bb_init(void)
+{
+ return driver_register(&fs_enet_bb_mdio_driver);
+}
+
+void fs_enet_mdio_bb_exit(void)
+{
+ driver_unregister(&fs_enet_bb_mdio_driver);
+}
+
diff --git a/drivers/net/fs_enet/mii-fec.c b/drivers/net/fs_enet/mii-fec.c
new file mode 100644
index 0000000..1328e10
--- /dev/null
+++ b/drivers/net/fs_enet/mii-fec.c
@@ -0,0 +1,243 @@
+/*
+ * Combined Ethernet driver for Motorola MPC8xx and MPC82xx.
+ *
+ * Copyright (c) 2003 Intracom S.A.
+ * by Pantelis Antoniou <panto@intracom.gr>
+ *
+ * 2005 (c) MontaVista Software, Inc.
+ * Vitaly Bordug <vbordug@ru.mvista.com>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/string.h>
+#include <linux/ptrace.h>
+#include <linux/errno.h>
+#include <linux/ioport.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/bitops.h>
+#include <linux/platform_device.h>
+
+#include <asm/pgtable.h>
+#include <asm/irq.h>
+#include <asm/uaccess.h>
+
+#include "fs_enet.h"
+#include "fec.h"
+
+/* Make MII read/write commands for the FEC.
+*/
+#define mk_mii_read(REG) (0x60020000 | ((REG & 0x1f) << 18))
+#define mk_mii_write(REG, VAL) (0x50020000 | ((REG & 0x1f) << 18) | (VAL & 0xffff))
+#define mk_mii_end 0
+
+#define FEC_MII_LOOPS 10000
+
+static int match_has_phy (struct device *dev, void* data)
+{
+ struct platform_device* pdev = container_of(dev, struct platform_device, dev);
+ struct fs_platform_info* fpi;
+ if(strcmp(pdev->name, (char*)data))
+ {
+ return 0;
+ }
+
+ fpi = pdev->dev.platform_data;
+ if((fpi)&&(fpi->has_phy))
+ return 1;
+ return 0;
+}
+
+static int fs_mii_fec_init(struct fec_info* fec, struct fs_mii_fec_platform_info *fmpi)
+{
+ struct resource *r;
+ fec_t *fecp;
+ char* name = "fsl-cpm-fec";
+
+ /* we need fec in order to be useful */
+ struct platform_device *fec_pdev =
+ container_of(bus_find_device(&platform_bus_type, NULL, name, match_has_phy),
+ struct platform_device, dev);
+
+ if(fec_pdev == NULL) {
+ printk(KERN_ERR"Unable to find PHY for %s", name);
+ return -ENODEV;
+ }
+
+ r = platform_get_resource_byname(fec_pdev, IORESOURCE_MEM, "regs");
+
+ fec->fecp = fecp = (fec_t*)ioremap(r->start,sizeof(fec_t));
+ fec->mii_speed = fmpi->mii_speed;
+
+ setbits32(&fecp->fec_r_cntrl, FEC_RCNTRL_MII_MODE); /* MII enable */
+ setbits32(&fecp->fec_ecntrl, FEC_ECNTRL_PINMUX | FEC_ECNTRL_ETHER_EN);
+ out_be32(&fecp->fec_ievent, FEC_ENET_MII);
+ out_be32(&fecp->fec_mii_speed, fec->mii_speed);
+
+ return 0;
+}
+
+static int fs_enet_fec_mii_read(struct mii_bus *bus , int phy_id, int location)
+{
+ struct fec_info* fec = bus->priv;
+ fec_t *fecp = fec->fecp;
+ int i, ret = -1;
+
+ if ((in_be32(&fecp->fec_r_cntrl) & FEC_RCNTRL_MII_MODE) == 0)
+ BUG();
+
+ /* Add PHY address to register command. */
+ out_be32(&fecp->fec_mii_data, (phy_id << 23) | mk_mii_read(location));
+
+ for (i = 0; i < FEC_MII_LOOPS; i++)
+ if ((in_be32(&fecp->fec_ievent) & FEC_ENET_MII) != 0)
+ break;
+
+ if (i < FEC_MII_LOOPS) {
+ out_be32(&fecp->fec_ievent, FEC_ENET_MII);
+ ret = in_be32(&fecp->fec_mii_data) & 0xffff;
+ }
+
+ return ret;
+
+}
+
+static int fs_enet_fec_mii_write(struct mii_bus *bus, int phy_id, int location, u16 val)
+{
+ struct fec_info* fec = bus->priv;
+ fec_t *fecp = fec->fecp;
+ int i;
+
+ /* this must never happen */
+ if ((in_be32(&fecp->fec_r_cntrl) & FEC_RCNTRL_MII_MODE) == 0)
+ BUG();
+
+ /* Add PHY address to register command. */
+ out_be32(&fecp->fec_mii_data, (phy_id << 23) | mk_mii_write(location, val));
+
+ for (i = 0; i < FEC_MII_LOOPS; i++)
+ if ((in_be32(&fecp->fec_ievent) & FEC_ENET_MII) != 0)
+ break;
+
+ if (i < FEC_MII_LOOPS)
+ out_be32(&fecp->fec_ievent, FEC_ENET_MII);
+
+ return 0;
+
+}
+
+static int fs_enet_fec_mii_reset(struct mii_bus *bus)
+{
+ /* nothing here - for now */
+ return 0;
+}
+
+static int __devinit fs_enet_fec_mdio_probe(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct fs_mii_fec_platform_info *pdata;
+ struct mii_bus *new_bus;
+ struct fec_info *fec;
+ int err = 0;
+ if (NULL == dev)
+ return -EINVAL;
+ new_bus = kzalloc(sizeof(struct mii_bus), GFP_KERNEL);
+
+ if (NULL == new_bus)
+ return -ENOMEM;
+
+ fec = kzalloc(sizeof(struct fec_info), GFP_KERNEL);
+
+ if (NULL == fec)
+ return -ENOMEM;
+
+ new_bus->name = "FEC MII Bus",
+ new_bus->read = &fs_enet_fec_mii_read,
+ new_bus->write = &fs_enet_fec_mii_write,
+ new_bus->reset = &fs_enet_fec_mii_reset,
+ new_bus->id = pdev->id;
+
+ pdata = (struct fs_mii_fec_platform_info *)pdev->dev.platform_data;
+
+ if (NULL == pdata) {
+ printk(KERN_ERR "fs_enet FEC mdio %d: Missing platform data!\n", pdev->id);
+ return -ENODEV;
+ }
+
+ /*set up workspace*/
+
+ fs_mii_fec_init(fec, pdata);
+ new_bus->priv = fec;
+
+ new_bus->irq = pdata->irq;
+
+ new_bus->dev = dev;
+ dev_set_drvdata(dev, new_bus);
+
+ err = mdiobus_register(new_bus);
+
+ if (0 != err) {
+ printk (KERN_ERR "%s: Cannot register as MDIO bus\n",
+ new_bus->name);
+ goto bus_register_fail;
+ }
+
+ return 0;
+
+bus_register_fail:
+ kfree(new_bus);
+
+ return err;
+}
+
+
+static int fs_enet_fec_mdio_remove(struct device *dev)
+{
+ struct mii_bus *bus = dev_get_drvdata(dev);
+
+ mdiobus_unregister(bus);
+
+ dev_set_drvdata(dev, NULL);
+ kfree(bus->priv);
+
+ bus->priv = NULL;
+ kfree(bus);
+
+ return 0;
+}
+
+static struct device_driver fs_enet_fec_mdio_driver = {
+ .name = "fsl-cpm-fec-mdio",
+ .bus = &platform_bus_type,
+ .probe = fs_enet_fec_mdio_probe,
+ .remove = fs_enet_fec_mdio_remove,
+};
+
+int fs_enet_mdio_fec_init(void)
+{
+ return driver_register(&fs_enet_fec_mdio_driver);
+}
+
+void fs_enet_mdio_fec_exit(void)
+{
+ driver_unregister(&fs_enet_fec_mdio_driver);
+}
+
diff --git a/drivers/net/fs_enet/mii-fixed.c b/drivers/net/fs_enet/mii-fixed.c
deleted file mode 100644
index b3e192d..0000000
--- a/drivers/net/fs_enet/mii-fixed.c
+++ /dev/null
@@ -1,92 +0,0 @@
-/*
- * Combined Ethernet driver for Motorola MPC8xx and MPC82xx.
- *
- * Copyright (c) 2003 Intracom S.A.
- * by Pantelis Antoniou <panto@intracom.gr>
- *
- * 2005 (c) MontaVista Software, Inc.
- * Vitaly Bordug <vbordug@ru.mvista.com>
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-
-#include <linux/config.h>
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/sched.h>
-#include <linux/string.h>
-#include <linux/ptrace.h>
-#include <linux/errno.h>
-#include <linux/ioport.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/pci.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/spinlock.h>
-#include <linux/mii.h>
-#include <linux/ethtool.h>
-#include <linux/bitops.h>
-
-#include <asm/pgtable.h>
-#include <asm/irq.h>
-#include <asm/uaccess.h>
-
-#include "fs_enet.h"
-
-static const u16 mii_regs[7] = {
- 0x3100,
- 0x786d,
- 0x0fff,
- 0x0fff,
- 0x01e1,
- 0x45e1,
- 0x0003,
-};
-
-static int mii_read(struct fs_enet_mii_bus *bus, int phy_id, int location)
-{
- int ret = 0;
-
- if ((unsigned int)location >= ARRAY_SIZE(mii_regs))
- return -1;
-
- if (location != 5)
- ret = mii_regs[location];
- else
- ret = bus->fixed.lpa;
-
- return ret;
-}
-
-static void mii_write(struct fs_enet_mii_bus *bus, int phy_id, int location, int val)
-{
- /* do nothing */
-}
-
-int fs_mii_fixed_init(struct fs_enet_mii_bus *bus)
-{
- const struct fs_mii_bus_info *bi = bus->bus_info;
-
- bus->fixed.lpa = 0x45e1; /* default 100Mb, full duplex */
-
- /* if speed is fixed at 10Mb, remove 100Mb modes */
- if (bi->i.fixed.speed == 10)
- bus->fixed.lpa &= ~LPA_100;
-
- /* if duplex is half, remove full duplex modes */
- if (bi->i.fixed.duplex == 0)
- bus->fixed.lpa &= ~LPA_DUPLEX;
-
- bus->mii_read = mii_read;
- bus->mii_write = mii_write;
-
- return 0;
-}
^ permalink raw reply related
* [PATCH 3/6] FS_ENET: use PAL for mii management (BSP part)
From: Vitaly Bordug @ 2006-06-23 23:17 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <20060623231648.6721.3495.stgit@localhost.localdomain>
This patch should update the board-specific parts of fs_enet infrastructure to utilize
Phy Abstraction Layer subsystem. Inside there are portions to respect driver changes for
8272ads, 885ads, 866ads, and 8560ads.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
---
arch/ppc/platforms/85xx/mpc8560_ads.c | 89 ++++++++++++
arch/ppc/platforms/85xx/mpc85xx_ads_common.h | 19 +++
arch/ppc/platforms/mpc8272ads_setup.c | 162 ++++++++++++----------
arch/ppc/platforms/mpc866ads_setup.c | 192 +++++++++++++-------------
arch/ppc/platforms/mpc885ads_setup.c | 177 +++++++++---------------
arch/ppc/platforms/pq2ads_pd.h | 82 -----------
arch/ppc/syslib/mpc85xx_devices.c | 89 ++++++++++++
arch/ppc/syslib/mpc8xx_devices.c | 8 +
arch/ppc/syslib/mpc8xx_sys.c | 6 +
arch/ppc/syslib/pq2_devices.c | 5 +
arch/ppc/syslib/pq2_sys.c | 3
include/asm-ppc/cpm2.h | 95 +++++++++++++
include/asm-ppc/mpc8260.h | 1
include/asm-ppc/mpc8xx.h | 1
include/linux/fs_enet_pd.h | 54 +++----
15 files changed, 585 insertions(+), 398 deletions(-)
diff --git a/arch/ppc/platforms/85xx/mpc8560_ads.c b/arch/ppc/platforms/85xx/mpc8560_ads.c
index 0cb2e86..92c46d8 100644
--- a/arch/ppc/platforms/85xx/mpc8560_ads.c
+++ b/arch/ppc/platforms/85xx/mpc8560_ads.c
@@ -30,6 +30,7 @@ #include <linux/serial_core.h>
#include <linux/initrd.h>
#include <linux/module.h>
#include <linux/fsl_devices.h>
+#include <linux/fs_enet_pd.h>
#include <asm/system.h>
#include <asm/pgtable.h>
@@ -59,6 +60,71 @@ #include <syslib/ppc85xx_setup.h>
* Setup the architecture
*
*/
+static void init_fcc_ioports(void)
+{
+ struct immap *immap;
+ struct io_port *io;
+ u32 tempval;
+
+ immap = cpm2_immr;
+
+ io = &immap->im_ioport;
+ /* FCC2/3 are on the ports B/C. */
+ tempval = in_be32(&io->iop_pdirb);
+ tempval &= ~PB2_DIRB0;
+ tempval |= PB2_DIRB1;
+ out_be32(&io->iop_pdirb, tempval);
+
+ tempval = in_be32(&io->iop_psorb);
+ tempval &= ~PB2_PSORB0;
+ tempval |= PB2_PSORB1;
+ out_be32(&io->iop_psorb, tempval);
+
+ tempval = in_be32(&io->iop_pparb);
+ tempval |= (PB2_DIRB0 | PB2_DIRB1);
+ out_be32(&io->iop_pparb, tempval);
+
+ tempval = in_be32(&io->iop_pdirb);
+ tempval &= ~PB3_DIRB0;
+ tempval |= PB3_DIRB1;
+ out_be32(&io->iop_pdirb, tempval);
+
+ tempval = in_be32(&io->iop_psorb);
+ tempval &= ~PB3_PSORB0;
+ tempval |= PB3_PSORB1;
+ out_be32(&io->iop_psorb, tempval);
+
+ tempval = in_be32(&io->iop_pparb);
+ tempval |= (PB3_DIRB0 | PB3_DIRB1);
+ out_be32(&io->iop_pparb, tempval);
+
+ tempval = in_be32(&io->iop_pdirc);
+ tempval |= PC3_DIRC1;
+ out_be32(&io->iop_pdirc, tempval);
+
+ tempval = in_be32(&io->iop_pparc);
+ tempval |= PC3_DIRC1;
+ out_be32(&io->iop_pparc, tempval);
+
+ /* Port C has clocks...... */
+ tempval = in_be32(&io->iop_psorc);
+ tempval &= ~(CLK_TRX);
+ out_be32(&io->iop_psorc, tempval);
+
+ tempval = in_be32(&io->iop_pdirc);
+ tempval &= ~(CLK_TRX);
+ out_be32(&io->iop_pdirc, tempval);
+ tempval = in_be32(&io->iop_pparc);
+ tempval |= (CLK_TRX);
+ out_be32(&io->iop_pparc, tempval);
+
+ /* Configure Serial Interface clock routing.
+ * First, clear all FCC bits to zero,
+ * then set the ones we want.
+ */
+ immap->im_cpmux.cmx_fcr &= ~(CPMUX_CLK_MASK);
+ immap->im_cpmux.cmx_fcr |= CPMUX_CLK_ROUTE;
+}
static void __init
mpc8560ads_setup_arch(void)
@@ -67,6 +133,7 @@ mpc8560ads_setup_arch(void)
unsigned int freq;
struct gianfar_platform_data *pdata;
struct gianfar_mdio_data *mdata;
+ struct fs_platform_info *fpi;
cpm2_reset();
@@ -109,6 +176,28 @@ #endif
pdata->bus_id = 0;
pdata->phy_id = 1;
memcpy(pdata->mac_addr, binfo->bi_enet1addr, 6);
+ }
+
+ init_fcc_ioports();
+ ppc_sys_device_remove(MPC85xx_CPM_FCC1);
+
+ fpi = (struct fs_platform_info *) ppc_sys_get_pdata(MPC85xx_CPM_FCC2);
+ if (fpi) {
+ memcpy(fpi->macaddr, binfo->bi_enet2addr, 6);
+ fpi->bus_id = "0:02";
+ fpi->phy_addr = 2;
+ fpi->dpram_offset = (u32)cpm2_immr->im_dprambase;
+ fpi->fcc_regs_c = (u32)&cpm2_immr->im_fcc_c[1];
+ }
+
+ fpi = (struct fs_platform_info *) ppc_sys_get_pdata(MPC85xx_CPM_FCC3);
+ if (fpi) {
+ memcpy(fpi->macaddr, binfo->bi_enet2addr, 6);
+ fpi->macaddr[5] += 1;
+ fpi->bus_id = "0:03";
+ fpi->phy_addr = 3;
+ fpi->dpram_offset = (u32)cpm2_immr->im_dprambase;
+ fpi->fcc_regs_c = (u32)&cpm2_immr->im_fcc_c[2];
}
#ifdef CONFIG_BLK_DEV_INITRD
diff --git a/arch/ppc/platforms/85xx/mpc85xx_ads_common.h b/arch/ppc/platforms/85xx/mpc85xx_ads_common.h
index de8d41a..86a4338 100644
--- a/arch/ppc/platforms/85xx/mpc85xx_ads_common.h
+++ b/arch/ppc/platforms/85xx/mpc85xx_ads_common.h
@@ -46,4 +46,23 @@ #define MPC85XX_PCI1_MEM_OFFSET 0x000000
#define MPC85XX_PCI1_IO_SIZE 0x01000000
+/* FCC1 Clock Source Configuration. These can be
+ * redefined in the board specific file.
+ * Can only choose from CLK9-12 */
+#define F1_RXCLK 12
+#define F1_TXCLK 11
+
+/* FCC2 Clock Source Configuration. These can be
+ * redefined in the board specific file.
+ * Can only choose from CLK13-16 */
+#define F2_RXCLK 13
+#define F2_TXCLK 14
+
+/* FCC3 Clock Source Configuration. These can be
+ * redefined in the board specific file.
+ * Can only choose from CLK13-16 */
+#define F3_RXCLK 15
+#define F3_TXCLK 16
+
+
#endif /* __MACH_MPC85XX_ADS_H__ */
diff --git a/arch/ppc/platforms/mpc8272ads_setup.c b/arch/ppc/platforms/mpc8272ads_setup.c
index abb7154..2a35fe2 100644
--- a/arch/ppc/platforms/mpc8272ads_setup.c
+++ b/arch/ppc/platforms/mpc8272ads_setup.c
@@ -56,66 +56,53 @@ static struct fs_uart_platform_info mpc8
},
};
-static struct fs_mii_bus_info mii_bus_info = {
- .method = fsmii_bitbang,
- .id = 0,
- .i.bitbang = {
- .mdio_port = fsiop_portc,
- .mdio_bit = 18,
- .mdc_port = fsiop_portc,
- .mdc_bit = 19,
- .delay = 1,
- },
-};
-
-static struct fs_platform_info mpc82xx_fcc1_pdata = {
- .fs_no = fsid_fcc1,
- .cp_page = CPM_CR_FCC1_PAGE,
- .cp_block = CPM_CR_FCC1_SBLOCK,
- .clk_trx = (PC_F1RXCLK | PC_F1TXCLK),
- .clk_route = CMX1_CLK_ROUTE,
- .clk_mask = CMX1_CLK_MASK,
- .init_ioports = init_fcc1_ioports,
-
- .phy_addr = 0,
-#ifdef PHY_INTERRUPT
- .phy_irq = PHY_INTERRUPT,
-#else
- .phy_irq = -1;
-#endif
- .mem_offset = FCC1_MEM_OFFSET,
- .bus_info = &mii_bus_info,
- .rx_ring = 32,
- .tx_ring = 32,
- .rx_copybreak = 240,
- .use_napi = 0,
- .napi_weight = 17,
-};
-
-static struct fs_platform_info mpc82xx_fcc2_pdata = {
- .fs_no = fsid_fcc2,
- .cp_page = CPM_CR_FCC2_PAGE,
- .cp_block = CPM_CR_FCC2_SBLOCK,
- .clk_trx = (PC_F2RXCLK | PC_F2TXCLK),
- .clk_route = CMX2_CLK_ROUTE,
- .clk_mask = CMX2_CLK_MASK,
- .init_ioports = init_fcc2_ioports,
-
- .phy_addr = 3,
-#ifdef PHY_INTERRUPT
- .phy_irq = PHY_INTERRUPT,
-#else
- .phy_irq = -1;
-#endif
- .mem_offset = FCC2_MEM_OFFSET,
- .bus_info = &mii_bus_info,
- .rx_ring = 32,
- .tx_ring = 32,
- .rx_copybreak = 240,
- .use_napi = 0,
- .napi_weight = 17,
-};
-
+static struct fs_mii_bb_platform_info m82xx_mii_bb_pdata = {
+ .mdio_dat.bit = 18,
+ .mdio_dir.bit = 18,
+ .mdc_dat.bit = 19,
+ .delay = 1,
+};
+
+static struct fs_platform_info mpc82xx_enet_pdata[] = {
+ [fsid_fcc1] = {
+ .fs_no = fsid_fcc1,
+ .cp_page = CPM_CR_FCC1_PAGE,
+ .cp_block = CPM_CR_FCC1_SBLOCK,
+
+ .clk_trx = (PC_F1RXCLK | PC_F1TXCLK),
+ .clk_route = CMX1_CLK_ROUTE,
+ .clk_mask = CMX1_CLK_MASK,
+ .init_ioports = init_fcc1_ioports,
+
+ .mem_offset = FCC1_MEM_OFFSET,
+
+ .rx_ring = 32,
+ .tx_ring = 32,
+ .rx_copybreak = 240,
+ .use_napi = 0,
+ .napi_weight = 17,
+ .bus_id = "0:00",
+ },
+ [fsid_fcc2] = {
+ .fs_no = fsid_fcc2,
+ .cp_page = CPM_CR_FCC2_PAGE,
+ .cp_block = CPM_CR_FCC2_SBLOCK,
+ .clk_trx = (PC_F2RXCLK | PC_F2TXCLK),
+ .clk_route = CMX2_CLK_ROUTE,
+ .clk_mask = CMX2_CLK_MASK,
+ .init_ioports = init_fcc2_ioports,
+
+ .mem_offset = FCC2_MEM_OFFSET,
+
+ .rx_ring = 32,
+ .tx_ring = 32,
+ .rx_copybreak = 240,
+ .use_napi = 0,
+ .napi_weight = 17,
+ .bus_id = "0:03",
+ },
+};
+
static void init_fcc1_ioports(void)
{
struct io_port *io;
@@ -209,20 +196,21 @@ static void __init mpc8272ads_fixup_enet
bd_t* bi = (void*)__res;
int fs_no = fsid_fcc1+pdev->id-1;
- mpc82xx_fcc1_pdata.dpram_offset = mpc82xx_fcc2_pdata.dpram_offset = (u32)cpm2_immr->im_dprambase;
- mpc82xx_fcc1_pdata.fcc_regs_c = mpc82xx_fcc2_pdata.fcc_regs_c = (u32)cpm2_immr->im_fcc_c;
-
- switch(fs_no) {
- case fsid_fcc1:
- memcpy(&mpc82xx_fcc1_pdata.macaddr,bi->bi_enetaddr,6);
- pdev->dev.platform_data = &mpc82xx_fcc1_pdata;
- break;
- case fsid_fcc2:
- memcpy(&mpc82xx_fcc2_pdata.macaddr,bi->bi_enetaddr,6);
- mpc82xx_fcc2_pdata.macaddr[5] ^= 1;
- pdev->dev.platform_data = &mpc82xx_fcc2_pdata;
- break;
+ if(fs_no > ARRAY_SIZE(mpc82xx_enet_pdata)) {
+ return;
}
+
+ mpc82xx_enet_pdata[fs_no].dpram_offset=
+ (u32)cpm2_immr->im_dprambase;
+ mpc82xx_enet_pdata[fs_no].fcc_regs_c =
+ (u32)cpm2_immr->im_fcc_c;
+ memcpy(&mpc82xx_enet_pdata[fs_no].macaddr,bi->bi_enetaddr,6);
+
+ /* prevent dup mac */
+ if(fs_no == fsid_fcc2)
+ mpc82xx_enet_pdata[fs_no].macaddr[5] ^= 1;
+
+ pdev->dev.platform_data = &mpc82xx_enet_pdata[fs_no];
}
static void mpc8272ads_fixup_uart_pdata(struct platform_device *pdev,
@@ -272,6 +260,29 @@ static void init_scc4_uart_ioports(void)
setbits32(&immap->im_cpmux.cmx_scr,0x0000001b);
iounmap(immap);
+}
+
+static void __init mpc8272ads_fixup_mdio_pdata(struct platform_device *pdev,
+ int idx)
+{
+ m82xx_mii_bb_pdata.irq[0] = PHY_INTERRUPT;
+ m82xx_mii_bb_pdata.irq[1] = -1;
+ m82xx_mii_bb_pdata.irq[2] = -1;
+ m82xx_mii_bb_pdata.irq[3] = PHY_INTERRUPT;
+ m82xx_mii_bb_pdata.irq[31] = -1;
+
+
+ m82xx_mii_bb_pdata.mdio_dat.offset =
+ (u32)&cpm2_immr->im_ioport.iop_pdatc;
+
+ m82xx_mii_bb_pdata.mdio_dir.offset =
+ (u32)&cpm2_immr->im_ioport.iop_pdirc;
+
+ m82xx_mii_bb_pdata.mdc_dat.offset =
+ (u32)&cpm2_immr->im_ioport.iop_pdatc;
+
+
+ pdev->dev.platform_data = &m82xx_mii_bb_pdata;
}
static int mpc8272ads_platform_notify(struct device *dev)
@@ -284,6 +295,10 @@ static int mpc8272ads_platform_notify(st
{
.bus_id = "fsl-cpm-scc:uart",
.rtn = mpc8272ads_fixup_uart_pdata,
+ },
+ {
+ .bus_id = "fsl-bb-mdio",
+ .rtn = mpc8272ads_fixup_mdio_pdata,
},
{
.bus_id = NULL
@@ -319,6 +334,7 @@ #ifdef CONFIG_SERIAL_CPM_SCC4
ppc_sys_device_enable(MPC82xx_CPM_SCC4);
#endif
+ ppc_sys_device_enable(MPC82xx_MDIO_BB);
return 0;
}
diff --git a/arch/ppc/platforms/mpc866ads_setup.c b/arch/ppc/platforms/mpc866ads_setup.c
index d919dab..ed71dd9 100644
--- a/arch/ppc/platforms/mpc866ads_setup.c
+++ b/arch/ppc/platforms/mpc866ads_setup.c
@@ -1,10 +1,10 @@
-/*arch/ppc/platforms/mpc885ads-setup.c
+/*arch/ppc/platforms/mpc866ads-setup.c
*
- * Platform setup for the Freescale mpc885ads board
+ * Platform setup for the Freescale mpc866ads board
*
* Vitaly Bordug <vbordug@ru.mvista.com>
*
- * Copyright 2005 MontaVista Software Inc.
+ * Copyright 2005-2006 MontaVista Software Inc.
*
* This file is licensed under the terms of the GNU General Public License
* version 2. This program is licensed "as is" without any warranty of any
@@ -43,49 +43,36 @@ static void setup_scc1_ioports(void);
static void setup_smc1_ioports(void);
static void setup_smc2_ioports(void);
-static struct fs_mii_bus_info fec_mii_bus_info = {
- .method = fsmii_fec,
- .id = 0,
-};
-
-static struct fs_mii_bus_info scc_mii_bus_info = {
- .method = fsmii_fixed,
- .id = 0,
- .i.fixed.speed = 10,
- .i.fixed.duplex = 0,
-};
+static struct fs_mii_fec_platform_info mpc8xx_mdio_fec_pdata;
-static struct fs_platform_info mpc8xx_fec_pdata[] = {
- {
- .rx_ring = 128,
- .tx_ring = 16,
- .rx_copybreak = 240,
+static struct fs_mii_fec_platform_info mpc8xx_mdio_fec_pdata;
- .use_napi = 1,
- .napi_weight = 17,
+static struct fs_platform_info mpc8xx_enet_pdata[] = {
+ [fsid_fec1] = {
+ .rx_ring = 128,
+ .tx_ring = 16,
+ .rx_copybreak = 240,
- .phy_addr = 15,
- .phy_irq = -1,
+ .use_napi = 1,
+ .napi_weight = 17,
- .use_rmii = 0,
+ .init_ioports = setup_fec1_ioports,
- .bus_info = &fec_mii_bus_info,
- }
-};
+ .bus_id = "0:0f",
+ .has_phy = 1,
+ },
+ [fsid_scc1] = {
+ .rx_ring = 64,
+ .tx_ring = 8,
+ .rx_copybreak = 240,
+ .use_napi = 1,
+ .napi_weight = 17,
-static struct fs_platform_info mpc8xx_scc_pdata = {
- .rx_ring = 64,
- .tx_ring = 8,
- .rx_copybreak = 240,
- .use_napi = 1,
- .napi_weight = 17,
+ .init_ioports = setup_scc1_ioports,
- .phy_addr = -1,
- .phy_irq = -1,
-
- .bus_info = &scc_mii_bus_info,
-
+ .bus_id = "fixed@100:1",
+ },
};
static struct fs_uart_platform_info mpc866_uart_pdata[] = {
@@ -207,64 +194,7 @@ static void setup_scc1_ioports(void)
setbits32(&immap->im_cpm.cp_pbdir, PB_ENET_TENA);
}
-
-static void mpc866ads_fixup_enet_pdata(struct platform_device *pdev, int fs_no)
-{
- struct fs_platform_info *fpi = pdev->dev.platform_data;
-
- volatile cpm8xx_t *cp;
- bd_t *bd = (bd_t *) __res;
- char *e;
- int i;
-
- /* Get pointer to Communication Processor */
- cp = cpmp;
- switch (fs_no) {
- case fsid_fec1:
- fpi = &mpc8xx_fec_pdata[0];
- fpi->init_ioports = &setup_fec1_ioports;
- break;
- case fsid_scc1:
- fpi = &mpc8xx_scc_pdata;
- fpi->init_ioports = &setup_scc1_ioports;
-
- break;
- default:
- printk(KERN_WARNING"Device %s is not supported!\n", pdev->name);
- return;
- }
-
- pdev->dev.platform_data = fpi;
- fpi->fs_no = fs_no;
-
- e = (unsigned char *)&bd->bi_enetaddr;
- for (i = 0; i < 6; i++)
- fpi->macaddr[i] = *e++;
-
- fpi->macaddr[5 - pdev->id]++;
-
-}
-
-static void mpc866ads_fixup_fec_enet_pdata(struct platform_device *pdev,
- int idx)
-{
- /* This is for FEC devices only */
- if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-fec")))
- return;
- mpc866ads_fixup_enet_pdata(pdev, fsid_fec1 + pdev->id - 1);
-}
-
-static void mpc866ads_fixup_scc_enet_pdata(struct platform_device *pdev,
- int idx)
-{
- /* This is for SCC devices only */
- if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-scc")))
- return;
-
- mpc866ads_fixup_enet_pdata(pdev, fsid_scc1 + pdev->id - 1);
-}
-
static void setup_smc1_ioports(void)
{
immap_t *immap = (immap_t *) IMAP_ADDR;
@@ -315,7 +245,57 @@ #else
#endif
}
+
+static int ma_count = 0;
+static void mpc866ads_fixup_enet_pdata(struct platform_device *pdev, int fs_no)
+{
+ struct fs_platform_info *fpi;
+
+ volatile cpm8xx_t *cp;
+ bd_t *bd = (bd_t *) __res;
+ char *e;
+ int i;
+
+ /* Get pointer to Communication Processor */
+ cp = cpmp;
+
+ if(fs_no > ARRAY_SIZE(mpc8xx_enet_pdata)) {
+ printk(KERN_ERR"No network-suitable #%d device on bus", fs_no);
+ return;
+ }
+
+
+ fpi = &mpc8xx_enet_pdata[fs_no];
+ fpi->fs_no = fs_no;
+ pdev->dev.platform_data = fpi;
+
+ e = (unsigned char *)&bd->bi_enetaddr;
+ for (i = 0; i < 6; i++)
+ fpi->macaddr[i] = *e++;
+
+ fpi->macaddr[5] += ma_count++;
+}
+
+static void mpc866ads_fixup_fec_enet_pdata(struct platform_device *pdev,
+ int idx)
+{
+ /* This is for FEC devices only */
+ if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-fec")))
+ return;
+ mpc866ads_fixup_enet_pdata(pdev, fsid_fec1 + pdev->id - 1);
+}
+
+static void mpc866ads_fixup_scc_enet_pdata(struct platform_device *pdev,
+ int idx)
+{
+ /* This is for SCC devices only */
+ if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-scc")))
+ return;
+
+ mpc866ads_fixup_enet_pdata(pdev, fsid_scc1 + pdev->id - 1);
+}
+
static void __init mpc866ads_fixup_uart_pdata(struct platform_device *pdev,
int idx)
{
@@ -360,6 +340,9 @@ static int mpc866ads_platform_notify(str
int __init mpc866ads_init(void)
{
+ bd_t *bd = (bd_t *) __res;
+ struct fs_mii_fec_platform_info* fmpi;
+
printk(KERN_NOTICE "mpc866ads: Init\n");
platform_notify = mpc866ads_platform_notify;
@@ -367,11 +350,20 @@ int __init mpc866ads_init(void)
ppc_sys_device_initfunc();
ppc_sys_device_disable_all();
-#ifdef MPC8xx_SECOND_ETH_SCC1
+#ifdef CONFIG_MPC8xx_SECOND_ETH_SCC1
ppc_sys_device_enable(MPC8xx_CPM_SCC1);
#endif
ppc_sys_device_enable(MPC8xx_CPM_FEC1);
+
+ ppc_sys_device_enable(MPC8xx_MDIO_FEC);
+
+ fmpi = ppc_sys_platform_devices[MPC8xx_MDIO_FEC].dev.platform_data =
+ &mpc8xx_mdio_fec_pdata;
+ fmpi->mii_speed = ((((bd->bi_intfreq + 4999999) / 2500000) / 2) & 0x3F) << 1;
+ /* No PHY interrupt line here */
+ fmpi->irq[0xf] = -1;
+
/* Since either of the uarts could be used as console, they need to ready */
#ifdef CONFIG_SERIAL_CPM_SMC1
ppc_sys_device_enable(MPC8xx_CPM_SMC1);
@@ -382,6 +374,14 @@ #ifdef CONFIG_SERIAL_CPM_SMC
ppc_sys_device_enable(MPC8xx_CPM_SMC2);
ppc_sys_device_setfunc(MPC8xx_CPM_SMC2, PPC_SYS_FUNC_UART);
#endif
+ ppc_sys_device_enable(MPC8xx_MDIO_FEC);
+
+ fmpi = ppc_sys_platform_devices[MPC8xx_MDIO_FEC].dev.platform_data =
+ &mpc8xx_mdio_fec_pdata;
+
+ fmpi->mii_speed = ((((bd->bi_intfreq + 4999999) / 2500000) / 2) & 0x3F) << 1;
+ /* No PHY interrupt line here */
+ fmpi->irq[0xf] = -1;
return 0;
}
diff --git a/arch/ppc/platforms/mpc885ads_setup.c b/arch/ppc/platforms/mpc885ads_setup.c
index 4b88679..97b3002 100644
--- a/arch/ppc/platforms/mpc885ads_setup.c
+++ b/arch/ppc/platforms/mpc885ads_setup.c
@@ -39,8 +39,11 @@ extern unsigned char __res[];
static void setup_smc1_ioports(void);
static void setup_smc2_ioports(void);
-static void __init mpc885ads_scc_phy_init(char);
-
+static struct fs_mii_fec_platform_info mpc8xx_mdio_fec_pdata;
+static void setup_fec1_ioports(void);
+static void setup_fec2_ioports(void);
+static void setup_scc3_ioports(void);
+
static struct fs_uart_platform_info mpc885_uart_pdata[] = {
[fsid_smc1_uart] = {
.brg = 1,
@@ -60,25 +63,10 @@ static struct fs_uart_platform_info mpc8
.rx_num_fifo = 4,
.rx_buf_size = 32,
},
-};
-
-static struct fs_mii_bus_info fec_mii_bus_info = {
- .method = fsmii_fec,
- .id = 0,
-};
-
-static struct fs_mii_bus_info scc_mii_bus_info = {
-#ifdef CONFIG_SCC_ENET_8xx_FIXED
- .method = fsmii_fixed,
-#else
- .method = fsmii_fec,
-#endif
-
- .id = 0,
};
-static struct fs_platform_info mpc8xx_fec_pdata[] = {
- {
+static struct fs_platform_info mpc8xx_enet_pdata[] = {
+ [fsid_fec1] = {
.rx_ring = 128,
.tx_ring = 16,
.rx_copybreak = 240,
@@ -86,47 +74,45 @@ static struct fs_platform_info mpc8xx_fe
.use_napi = 1,
.napi_weight = 17,
- .phy_addr = 0,
- .phy_irq = SIU_IRQ7,
+ .init_ioports = setup_fec1_ioports,
- .bus_info = &fec_mii_bus_info,
- }, {
+ .bus_id = "0:00",
+ .has_phy = 1,
+ },
+ [fsid_fec2] = {
.rx_ring = 128,
.tx_ring = 16,
.rx_copybreak = 240,
.use_napi = 1,
.napi_weight = 17,
-
- .phy_addr = 1,
- .phy_irq = SIU_IRQ7,
- .bus_info = &fec_mii_bus_info,
- }
-};
+ .init_ioports = setup_fec2_ioports,
-static struct fs_platform_info mpc8xx_scc_pdata = {
- .rx_ring = 64,
- .tx_ring = 8,
- .rx_copybreak = 240,
+ .bus_id = "0:01",
+ .has_phy = 1,
+ },
+ [fsid_scc3] = {
+ .rx_ring = 64,
+ .tx_ring = 8,
+ .rx_copybreak = 240,
- .use_napi = 1,
- .napi_weight = 17,
+ .use_napi = 1,
+ .napi_weight = 17,
- .phy_addr = 2,
-#ifdef CONFIG_MPC8xx_SCC_ENET_FIXED
- .phy_irq = -1,
+ .init_ioports = setup_scc3_ioports,
+#ifdef CONFIG_FIXED_MII_10_FDX
+ .bus_id = "fixed@100:1",
#else
- .phy_irq = SIU_IRQ7,
-#endif
-
- .bus_info = &scc_mii_bus_info,
+ .bus_id = "0:02",
+ #endif
+ },
};
void __init board_init(void)
{
- volatile cpm8xx_t *cp = cpmp;
- unsigned int *bcsr_io;
+ cpm8xx_t *cp = cpmp;
+ unsigned int *bcsr_io;
#ifdef CONFIG_FS_ENET
immap_t *immap = (immap_t *) IMAP_ADDR;
@@ -165,6 +151,14 @@ #ifdef CONFIG_FS_ENET
/* use MDC for MII (common) */
setbits16(&immap->im_ioport.iop_pdpar, 0x0080);
clrbits16(&immap->im_ioport.iop_pddir, 0x0080);
+ bcsr_io = ioremap(BCSR5, sizeof(unsigned long));
+ clrbits32(bcsr_io,BCSR5_MII1_EN);
+ clrbits32(bcsr_io,BCSR5_MII1_RST);
+#ifdef CONFIG_MPC8xx_SECOND_ETH_FEC2
+ clrbits32(bcsr_io,BCSR5_MII2_EN);
+ clrbits32(bcsr_io,BCSR5_MII2_RST);
+#endif
+ iounmap(bcsr_io);
#endif
}
@@ -195,8 +189,8 @@ static void setup_fec2_ioports(void)
/* configure FEC2 pins */
setbits32(&immap->im_cpm.cp_pepar, 0x0003fffc);
setbits32(&immap->im_cpm.cp_pedir, 0x0003fffc);
- setbits32(&immap->im_cpm.cp_peso, 0x00037800);
clrbits32(&immap->im_cpm.cp_peso, 0x000087fc);
+ setbits32(&immap->im_cpm.cp_peso, 0x00037800);
clrbits32(&immap->im_cpm.cp_cptr, 0x00000080);
}
@@ -214,6 +208,8 @@ static void setup_scc3_ioports(void)
/* Enable the PHY.
*/
+ clrbits32(bcsr_io+4, BCSR4_ETH10_RST);
+ udelay(1000);
setbits32(bcsr_io+4, BCSR4_ETH10_RST);
/* Configure port A pins for Txd and Rxd.
*/
@@ -255,37 +251,38 @@ static void setup_scc3_ioports(void)
clrbits32(&immap->im_cpm.cp_pedir, PE_ENET_TENA);
setbits32(&immap->im_cpm.cp_peso, PE_ENET_TENA);
- setbits32(bcsr_io+1, BCSR1_ETHEN);
+ setbits32(bcsr_io+4, BCSR1_ETHEN);
iounmap(bcsr_io);
}
+
+static int mac_count = 0;
static void mpc885ads_fixup_enet_pdata(struct platform_device *pdev, int fs_no)
{
- struct fs_platform_info *fpi = pdev->dev.platform_data;
-
- volatile cpm8xx_t *cp;
+ struct fs_platform_info *fpi;
bd_t *bd = (bd_t *) __res;
char *e;
int i;
+
+ if(fs_no > ARRAY_SIZE(mpc8xx_enet_pdata)) {
+ printk(KERN_ERR"No network-suitable #%d device on bus", fs_no);
+ return;
+ }
+
+ fpi = &mpc8xx_enet_pdata[fs_no];
- /* Get pointer to Communication Processor */
- cp = cpmp;
switch (fs_no) {
case fsid_fec1:
- fpi = &mpc8xx_fec_pdata[0];
fpi->init_ioports = &setup_fec1_ioports;
break;
case fsid_fec2:
- fpi = &mpc8xx_fec_pdata[1];
fpi->init_ioports = &setup_fec2_ioports;
break;
case fsid_scc3:
- fpi = &mpc8xx_scc_pdata;
fpi->init_ioports = &setup_scc3_ioports;
- mpc885ads_scc_phy_init(fpi->phy_addr);
break;
default:
- printk(KERN_WARNING"Device %s is not supported!\n", pdev->name);
+ printk(KERN_WARNING "Device %s is not supported!\n", pdev->name);
return;
}
@@ -296,7 +293,7 @@ static void mpc885ads_fixup_enet_pdata(s
for (i = 0; i < 6; i++)
fpi->macaddr[i] = *e++;
- fpi->macaddr[5 - pdev->id]++;
+ fpi->macaddr[5] += mac_count++;
}
@@ -319,58 +316,6 @@ static void __init mpc885ads_fixup_scc_e
mpc885ads_fixup_enet_pdata(pdev, fsid_scc1 + pdev->id - 1);
}
-/* SCC ethernet controller does not have MII management channel. FEC1 MII
- * channel is used to communicate with the 10Mbit PHY.
- */
-
-#define MII_ECNTRL_PINMUX 0x4
-#define FEC_ECNTRL_PINMUX 0x00000004
-#define FEC_RCNTRL_MII_MODE 0x00000004
-
-/* Make MII read/write commands.
- */
-#define mk_mii_write(REG, VAL, PHY_ADDR) (0x50020000 | (((REG) & 0x1f) << 18) | \
- ((VAL) & 0xffff) | ((PHY_ADDR) << 23))
-
-static void mpc885ads_scc_phy_init(char phy_addr)
-{
- volatile immap_t *immap;
- volatile fec_t *fecp;
- bd_t *bd;
-
- bd = (bd_t *) __res;
- immap = (immap_t *) IMAP_ADDR; /* pointer to internal registers */
- fecp = &(immap->im_cpm.cp_fec);
-
- /* Enable MII pins of the FEC1
- */
- setbits16(&immap->im_ioport.iop_pdpar, 0x0080);
- clrbits16(&immap->im_ioport.iop_pddir, 0x0080);
- /* Set MII speed to 2.5 MHz
- */
- out_be32(&fecp->fec_mii_speed,
- ((((bd->bi_intfreq + 4999999) / 2500000) / 2) & 0x3F) << 1);
-
- /* Enable FEC pin MUX
- */
- setbits32(&fecp->fec_ecntrl, MII_ECNTRL_PINMUX);
- setbits32(&fecp->fec_r_cntrl, FEC_RCNTRL_MII_MODE);
-
- out_be32(&fecp->fec_mii_data,
- mk_mii_write(MII_BMCR, BMCR_ISOLATE, phy_addr));
- udelay(100);
- out_be32(&fecp->fec_mii_data,
- mk_mii_write(MII_ADVERTISE,
- ADVERTISE_10HALF | ADVERTISE_CSMA, phy_addr));
- udelay(100);
-
- /* Disable FEC MII settings
- */
- clrbits32(&fecp->fec_ecntrl, MII_ECNTRL_PINMUX);
- clrbits32(&fecp->fec_r_cntrl, FEC_RCNTRL_MII_MODE);
- out_be32(&fecp->fec_mii_speed, 0);
-}
-
static void setup_smc1_ioports(void)
{
immap_t *immap = (immap_t *) IMAP_ADDR;
@@ -463,6 +408,9 @@ static int mpc885ads_platform_notify(str
int __init mpc885ads_init(void)
{
+ struct fs_mii_fec_platform_info* fmpi;
+ bd_t *bd = (bd_t *) __res;
+
printk(KERN_NOTICE "mpc885ads: Init\n");
platform_notify = mpc885ads_platform_notify;
@@ -471,9 +419,18 @@ int __init mpc885ads_init(void)
ppc_sys_device_disable_all();
ppc_sys_device_enable(MPC8xx_CPM_FEC1);
+
+ ppc_sys_device_enable(MPC8xx_MDIO_FEC);
+ fmpi = ppc_sys_platform_devices[MPC8xx_MDIO_FEC].dev.platform_data =
+ &mpc8xx_mdio_fec_pdata;
+
+ fmpi->mii_speed = ((((bd->bi_intfreq + 4999999) / 2500000) / 2) & 0x3F) << 1;
+
+ /* No PHY interrupt line here */
+ fmpi->irq[0xf] = SIU_IRQ7;
#ifdef CONFIG_MPC8xx_SECOND_ETH_SCC3
- ppc_sys_device_enable(MPC8xx_CPM_SCC1);
+ ppc_sys_device_enable(MPC8xx_CPM_SCC3);
#endif
#ifdef CONFIG_MPC8xx_SECOND_ETH_FEC2
diff --git a/arch/ppc/platforms/pq2ads_pd.h b/arch/ppc/platforms/pq2ads_pd.h
index 8f14a43..672483d 100644
--- a/arch/ppc/platforms/pq2ads_pd.h
+++ b/arch/ppc/platforms/pq2ads_pd.h
@@ -29,86 +29,4 @@ #define F2_TXCLK 16
#define F3_RXCLK 13
#define F3_TXCLK 14
-/* Automatically generates register configurations */
-#define PC_CLK(x) ((uint)(1<<(x-1))) /* FCC CLK I/O ports */
-
-#define CMXFCR_RF1CS(x) ((uint)((x-5)<<27)) /* FCC1 Receive Clock Source */
-#define CMXFCR_TF1CS(x) ((uint)((x-5)<<24)) /* FCC1 Transmit Clock Source */
-#define CMXFCR_RF2CS(x) ((uint)((x-9)<<19)) /* FCC2 Receive Clock Source */
-#define CMXFCR_TF2CS(x) ((uint)((x-9)<<16)) /* FCC2 Transmit Clock Source */
-#define CMXFCR_RF3CS(x) ((uint)((x-9)<<11)) /* FCC3 Receive Clock Source */
-#define CMXFCR_TF3CS(x) ((uint)((x-9)<<8)) /* FCC3 Transmit Clock Source */
-
-#define PC_F1RXCLK PC_CLK(F1_RXCLK)
-#define PC_F1TXCLK PC_CLK(F1_TXCLK)
-#define CMX1_CLK_ROUTE (CMXFCR_RF1CS(F1_RXCLK) | CMXFCR_TF1CS(F1_TXCLK))
-#define CMX1_CLK_MASK ((uint)0xff000000)
-
-#define PC_F2RXCLK PC_CLK(F2_RXCLK)
-#define PC_F2TXCLK PC_CLK(F2_TXCLK)
-#define CMX2_CLK_ROUTE (CMXFCR_RF2CS(F2_RXCLK) | CMXFCR_TF2CS(F2_TXCLK))
-#define CMX2_CLK_MASK ((uint)0x00ff0000)
-
-#define PC_F3RXCLK PC_CLK(F3_RXCLK)
-#define PC_F3TXCLK PC_CLK(F3_TXCLK)
-#define CMX3_CLK_ROUTE (CMXFCR_RF3CS(F3_RXCLK) | CMXFCR_TF3CS(F3_TXCLK))
-#define CMX3_CLK_MASK ((uint)0x0000ff00)
-
-/* I/O Pin assignment for FCC1. I don't yet know the best way to do this,
- * but there is little variation among the choices.
- */
-#define PA1_COL 0x00000001U
-#define PA1_CRS 0x00000002U
-#define PA1_TXER 0x00000004U
-#define PA1_TXEN 0x00000008U
-#define PA1_RXDV 0x00000010U
-#define PA1_RXER 0x00000020U
-#define PA1_TXDAT 0x00003c00U
-#define PA1_RXDAT 0x0003c000U
-#define PA1_PSORA0 (PA1_RXDAT | PA1_TXDAT)
-#define PA1_PSORA1 (PA1_COL | PA1_CRS | PA1_TXER | PA1_TXEN | \
- PA1_RXDV | PA1_RXER)
-#define PA1_DIRA0 (PA1_RXDAT | PA1_CRS | PA1_COL | PA1_RXER | PA1_RXDV)
-#define PA1_DIRA1 (PA1_TXDAT | PA1_TXEN | PA1_TXER)
-
-
-/* I/O Pin assignment for FCC2. I don't yet know the best way to do this,
- * but there is little variation among the choices.
- */
-#define PB2_TXER 0x00000001U
-#define PB2_RXDV 0x00000002U
-#define PB2_TXEN 0x00000004U
-#define PB2_RXER 0x00000008U
-#define PB2_COL 0x00000010U
-#define PB2_CRS 0x00000020U
-#define PB2_TXDAT 0x000003c0U
-#define PB2_RXDAT 0x00003c00U
-#define PB2_PSORB0 (PB2_RXDAT | PB2_TXDAT | PB2_CRS | PB2_COL | \
- PB2_RXER | PB2_RXDV | PB2_TXER)
-#define PB2_PSORB1 (PB2_TXEN)
-#define PB2_DIRB0 (PB2_RXDAT | PB2_CRS | PB2_COL | PB2_RXER | PB2_RXDV)
-#define PB2_DIRB1 (PB2_TXDAT | PB2_TXEN | PB2_TXER)
-
-
-/* I/O Pin assignment for FCC3. I don't yet know the best way to do this,
- * but there is little variation among the choices.
- */
-#define PB3_RXDV 0x00004000U
-#define PB3_RXER 0x00008000U
-#define PB3_TXER 0x00010000U
-#define PB3_TXEN 0x00020000U
-#define PB3_COL 0x00040000U
-#define PB3_CRS 0x00080000U
-#define PB3_TXDAT 0x0f000000U
-#define PB3_RXDAT 0x00f00000U
-#define PB3_PSORB0 (PB3_RXDAT | PB3_TXDAT | PB3_CRS | PB3_COL | \
- PB3_RXER | PB3_RXDV | PB3_TXER | PB3_TXEN)
-#define PB3_PSORB1 0
-#define PB3_DIRB0 (PB3_RXDAT | PB3_CRS | PB3_COL | PB3_RXER | PB3_RXDV)
-#define PB3_DIRB1 (PB3_TXDAT | PB3_TXEN | PB3_TXER)
-
-#define FCC_MEM_OFFSET(x) (CPM_FCC_SPECIAL_BASE + (x*128))
-#define FCC1_MEM_OFFSET FCC_MEM_OFFSET(0)
-#define FCC2_MEM_OFFSET FCC_MEM_OFFSET(1)
-
#endif
diff --git a/arch/ppc/syslib/mpc85xx_devices.c b/arch/ppc/syslib/mpc85xx_devices.c
index 7735336..325136e 100644
--- a/arch/ppc/syslib/mpc85xx_devices.c
+++ b/arch/ppc/syslib/mpc85xx_devices.c
@@ -16,9 +16,11 @@ #include <linux/module.h>
#include <linux/device.h>
#include <linux/serial_8250.h>
#include <linux/fsl_devices.h>
+#include <linux/fs_enet_pd.h>
#include <asm/mpc85xx.h>
#include <asm/irq.h>
#include <asm/ppc_sys.h>
+#include <asm/cpm2.h>
/* We use offsets for IORESOURCE_MEM since we do not know at compile time
* what CCSRBAR is, will get fixed up by mach_mpc85xx_fixup
@@ -82,6 +84,60 @@ static struct fsl_i2c_platform_data mpc8
.device_flags = FSL_I2C_DEV_SEPARATE_DFSRR,
};
+static struct fs_platform_info mpc85xx_fcc1_pdata = {
+ .fs_no = fsid_fcc1,
+ .cp_page = CPM_CR_FCC1_PAGE,
+ .cp_block = CPM_CR_FCC1_SBLOCK,
+
+ .rx_ring = 32,
+ .tx_ring = 32,
+ .rx_copybreak = 240,
+ .use_napi = 0,
+ .napi_weight = 17,
+
+ .clk_mask = CMX1_CLK_MASK,
+ .clk_route = CMX1_CLK_ROUTE,
+ .clk_trx = (PC_F1RXCLK | PC_F1TXCLK),
+
+ .mem_offset = FCC1_MEM_OFFSET,
+};
+
+static struct fs_platform_info mpc85xx_fcc2_pdata = {
+ .fs_no = fsid_fcc2,
+ .cp_page = CPM_CR_FCC2_PAGE,
+ .cp_block = CPM_CR_FCC2_SBLOCK,
+
+ .rx_ring = 32,
+ .tx_ring = 32,
+ .rx_copybreak = 240,
+ .use_napi = 0,
+ .napi_weight = 17,
+
+ .clk_mask = CMX2_CLK_MASK,
+ .clk_route = CMX2_CLK_ROUTE,
+ .clk_trx = (PC_F2RXCLK | PC_F2TXCLK),
+
+ .mem_offset = FCC2_MEM_OFFSET,
+};
+
+static struct fs_platform_info mpc85xx_fcc3_pdata = {
+ .fs_no = fsid_fcc3,
+ .cp_page = CPM_CR_FCC3_PAGE,
+ .cp_block = CPM_CR_FCC3_SBLOCK,
+
+ .rx_ring = 32,
+ .tx_ring = 32,
+ .rx_copybreak = 240,
+ .use_napi = 0,
+ .napi_weight = 17,
+
+ .clk_mask = CMX3_CLK_MASK,
+ .clk_route = CMX3_CLK_ROUTE,
+ .clk_trx = (PC_F3RXCLK | PC_F3TXCLK),
+
+ .mem_offset = FCC3_MEM_OFFSET,
+};
+
static struct plat_serial8250_port serial_platform_data[] = {
[0] = {
.mapbase = 0x4500,
@@ -318,19 +374,28 @@ struct platform_device ppc_sys_platform_
[MPC85xx_CPM_FCC1] = {
.name = "fsl-cpm-fcc",
.id = 1,
- .num_resources = 3,
+ .num_resources = 4,
+ .dev.platform_data = &mpc85xx_fcc1_pdata,
.resource = (struct resource[]) {
{
+ .name = "fcc_regs",
.start = 0x91300,
.end = 0x9131F,
.flags = IORESOURCE_MEM,
},
{
+ .name = "fcc_regs_c",
.start = 0x91380,
.end = 0x9139F,
.flags = IORESOURCE_MEM,
},
{
+ .name = "fcc_pram",
+ .start = 0x88400,
+ .end = 0x884ff,
+ .flags = IORESOURCE_MEM,
+ },
+ {
.start = SIU_INT_FCC1,
.end = SIU_INT_FCC1,
.flags = IORESOURCE_IRQ,
@@ -340,19 +405,28 @@ struct platform_device ppc_sys_platform_
[MPC85xx_CPM_FCC2] = {
.name = "fsl-cpm-fcc",
.id = 2,
- .num_resources = 3,
+ .num_resources = 4,
+ .dev.platform_data = &mpc85xx_fcc2_pdata,
.resource = (struct resource[]) {
{
+ .name = "fcc_regs",
.start = 0x91320,
.end = 0x9133F,
.flags = IORESOURCE_MEM,
},
{
+ .name = "fcc_regs_c",
.start = 0x913A0,
.end = 0x913CF,
.flags = IORESOURCE_MEM,
},
{
+ .name = "fcc_pram",
+ .start = 0x88500,
+ .end = 0x885ff,
+ .flags = IORESOURCE_MEM,
+ },
+ {
.start = SIU_INT_FCC2,
.end = SIU_INT_FCC2,
.flags = IORESOURCE_IRQ,
@@ -362,16 +436,25 @@ struct platform_device ppc_sys_platform_
[MPC85xx_CPM_FCC3] = {
.name = "fsl-cpm-fcc",
.id = 3,
- .num_resources = 3,
+ .num_resources = 4,
+ .dev.platform_data = &mpc85xx_fcc3_pdata,
.resource = (struct resource[]) {
{
+ .name = "fcc_regs",
.start = 0x91340,
.end = 0x9135F,
.flags = IORESOURCE_MEM,
},
{
+ .name = "fcc_regs_c",
.start = 0x913D0,
.end = 0x913FF,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .name = "fcc_pram",
+ .start = 0x88600,
+ .end = 0x886ff,
.flags = IORESOURCE_MEM,
},
{
diff --git a/arch/ppc/syslib/mpc8xx_devices.c b/arch/ppc/syslib/mpc8xx_devices.c
index 6f53638..cf5ab47 100644
--- a/arch/ppc/syslib/mpc8xx_devices.c
+++ b/arch/ppc/syslib/mpc8xx_devices.c
@@ -218,6 +218,14 @@ struct platform_device ppc_sys_platform_
},
},
},
+
+ [MPC8xx_MDIO_FEC] = {
+ .name = "fsl-cpm-fec-mdio",
+ .id = 0,
+ .num_resources = 0,
+
+ },
+
};
static int __init mach_mpc8xx_fixup(struct platform_device *pdev)
diff --git a/arch/ppc/syslib/mpc8xx_sys.c b/arch/ppc/syslib/mpc8xx_sys.c
index eee2132..18ba1d7 100644
--- a/arch/ppc/syslib/mpc8xx_sys.c
+++ b/arch/ppc/syslib/mpc8xx_sys.c
@@ -22,7 +22,7 @@ struct ppc_sys_spec ppc_sys_specs[] = {
.ppc_sys_name = "MPC86X",
.mask = 0xFFFFFFFF,
.value = 0x00000000,
- .num_devices = 7,
+ .num_devices = 8,
.device_list = (enum ppc_sys_devices[])
{
MPC8xx_CPM_FEC1,
@@ -32,13 +32,14 @@ struct ppc_sys_spec ppc_sys_specs[] = {
MPC8xx_CPM_SCC4,
MPC8xx_CPM_SMC1,
MPC8xx_CPM_SMC2,
+ MPC8xx_MDIO_FEC,
},
},
{
.ppc_sys_name = "MPC885",
.mask = 0xFFFFFFFF,
.value = 0x00000000,
- .num_devices = 8,
+ .num_devices = 9,
.device_list = (enum ppc_sys_devices[])
{
MPC8xx_CPM_FEC1,
@@ -49,6 +50,7 @@ struct ppc_sys_spec ppc_sys_specs[] = {
MPC8xx_CPM_SCC4,
MPC8xx_CPM_SMC1,
MPC8xx_CPM_SMC2,
+ MPC8xx_MDIO_FEC,
},
},
{ /* default match */
diff --git a/arch/ppc/syslib/pq2_devices.c b/arch/ppc/syslib/pq2_devices.c
index 8692d00..fefbc21 100644
--- a/arch/ppc/syslib/pq2_devices.c
+++ b/arch/ppc/syslib/pq2_devices.c
@@ -369,6 +369,11 @@ struct platform_device ppc_sys_platform_
},
},
},
+ [MPC82xx_MDIO_BB] = {
+ .name = "fsl-bb-mdio",
+ .id = 0,
+ .num_resources = 0,
+ },
};
static int __init mach_mpc82xx_fixup(struct platform_device *pdev)
diff --git a/arch/ppc/syslib/pq2_sys.c b/arch/ppc/syslib/pq2_sys.c
index fee8948..f52600c 100644
--- a/arch/ppc/syslib/pq2_sys.c
+++ b/arch/ppc/syslib/pq2_sys.c
@@ -139,13 +139,14 @@ struct ppc_sys_spec ppc_sys_specs[] = {
.ppc_sys_name = "8272",
.mask = 0x0000ff00,
.value = 0x00000c00,
- .num_devices = 12,
+ .num_devices = 13,
.device_list = (enum ppc_sys_devices[])
{
MPC82xx_CPM_FCC1, MPC82xx_CPM_FCC2, MPC82xx_CPM_SCC1,
MPC82xx_CPM_SCC2, MPC82xx_CPM_SCC3, MPC82xx_CPM_SCC4,
MPC82xx_CPM_SMC1, MPC82xx_CPM_SMC2, MPC82xx_CPM_SPI,
MPC82xx_CPM_I2C, MPC82xx_CPM_USB, MPC82xx_SEC1,
+ MPC82xx_MDIO_BB,
},
},
/* below is a list of the 8280 family of processors */
diff --git a/include/asm-ppc/cpm2.h b/include/asm-ppc/cpm2.h
index c70344b..f6a7ff0 100644
--- a/include/asm-ppc/cpm2.h
+++ b/include/asm-ppc/cpm2.h
@@ -1093,5 +1093,100 @@ #endif
#define FCC_PSMR_RMII ((uint)0x00020000) /* Use RMII interface */
+/* FCC iop & clock configuration. BSP code is responsible to define Fx_RXCLK & Fx_TXCLK
+ * in order to use clock-computing stuff below for the FCC x
+ */
+
+/* Automatically generates register configurations */
+#define PC_CLK(x) ((uint)(1<<(x-1))) /* FCC CLK I/O ports */
+
+#define CMXFCR_RF1CS(x) ((uint)((x-5)<<27)) /* FCC1 Receive Clock Source */
+#define CMXFCR_TF1CS(x) ((uint)((x-5)<<24)) /* FCC1 Transmit Clock Source */
+#define CMXFCR_RF2CS(x) ((uint)((x-9)<<19)) /* FCC2 Receive Clock Source */
+#define CMXFCR_TF2CS(x) ((uint)((x-9)<<16)) /* FCC2 Transmit Clock Source */
+#define CMXFCR_RF3CS(x) ((uint)((x-9)<<11)) /* FCC3 Receive Clock Source */
+#define CMXFCR_TF3CS(x) ((uint)((x-9)<<8)) /* FCC3 Transmit Clock Source */
+
+#define PC_F1RXCLK PC_CLK(F1_RXCLK)
+#define PC_F1TXCLK PC_CLK(F1_TXCLK)
+#define CMX1_CLK_ROUTE (CMXFCR_RF1CS(F1_RXCLK) | CMXFCR_TF1CS(F1_TXCLK))
+#define CMX1_CLK_MASK ((uint)0xff000000)
+
+#define PC_F2RXCLK PC_CLK(F2_RXCLK)
+#define PC_F2TXCLK PC_CLK(F2_TXCLK)
+#define CMX2_CLK_ROUTE (CMXFCR_RF2CS(F2_RXCLK) | CMXFCR_TF2CS(F2_TXCLK))
+#define CMX2_CLK_MASK ((uint)0x00ff0000)
+
+#define PC_F3RXCLK PC_CLK(F3_RXCLK)
+#define PC_F3TXCLK PC_CLK(F3_TXCLK)
+#define CMX3_CLK_ROUTE (CMXFCR_RF3CS(F3_RXCLK) | CMXFCR_TF3CS(F3_TXCLK))
+#define CMX3_CLK_MASK ((uint)0x0000ff00)
+
+#define CPMUX_CLK_MASK (CMX3_CLK_MASK | CMX2_CLK_MASK)
+#define CPMUX_CLK_ROUTE (CMX3_CLK_ROUTE | CMX2_CLK_ROUTE)
+
+#define CLK_TRX (PC_F3TXCLK | PC_F3RXCLK | PC_F2TXCLK | PC_F2RXCLK)
+
+/* I/O Pin assignment for FCC1. I don't yet know the best way to do this,
+ * but there is little variation among the choices.
+ */
+#define PA1_COL 0x00000001U
+#define PA1_CRS 0x00000002U
+#define PA1_TXER 0x00000004U
+#define PA1_TXEN 0x00000008U
+#define PA1_RXDV 0x00000010U
+#define PA1_RXER 0x00000020U
+#define PA1_TXDAT 0x00003c00U
+#define PA1_RXDAT 0x0003c000U
+#define PA1_PSORA0 (PA1_RXDAT | PA1_TXDAT)
+#define PA1_PSORA1 (PA1_COL | PA1_CRS | PA1_TXER | PA1_TXEN | \
+ PA1_RXDV | PA1_RXER)
+#define PA1_DIRA0 (PA1_RXDAT | PA1_CRS | PA1_COL | PA1_RXER | PA1_RXDV)
+#define PA1_DIRA1 (PA1_TXDAT | PA1_TXEN | PA1_TXER)
+
+
+/* I/O Pin assignment for FCC2. I don't yet know the best way to do this,
+ * but there is little variation among the choices.
+ */
+#define PB2_TXER 0x00000001U
+#define PB2_RXDV 0x00000002U
+#define PB2_TXEN 0x00000004U
+#define PB2_RXER 0x00000008U
+#define PB2_COL 0x00000010U
+#define PB2_CRS 0x00000020U
+#define PB2_TXDAT 0x000003c0U
+#define PB2_RXDAT 0x00003c00U
+#define PB2_PSORB0 (PB2_RXDAT | PB2_TXDAT | PB2_CRS | PB2_COL | \
+ PB2_RXER | PB2_RXDV | PB2_TXER)
+#define PB2_PSORB1 (PB2_TXEN)
+#define PB2_DIRB0 (PB2_RXDAT | PB2_CRS | PB2_COL | PB2_RXER | PB2_RXDV)
+#define PB2_DIRB1 (PB2_TXDAT | PB2_TXEN | PB2_TXER)
+
+
+/* I/O Pin assignment for FCC3. I don't yet know the best way to do this,
+ * but there is little variation among the choices.
+ */
+#define PB3_RXDV 0x00004000U
+#define PB3_RXER 0x00008000U
+#define PB3_TXER 0x00010000U
+#define PB3_TXEN 0x00020000U
+#define PB3_COL 0x00040000U
+#define PB3_CRS 0x00080000U
+#define PB3_TXDAT 0x0f000000U
+#define PC3_TXDAT 0x00000010U
+#define PB3_RXDAT 0x00f00000U
+#define PB3_PSORB0 (PB3_RXDAT | PB3_TXDAT | PB3_CRS | PB3_COL | \
+ PB3_RXER | PB3_RXDV | PB3_TXER | PB3_TXEN)
+#define PB3_PSORB1 0
+#define PB3_DIRB0 (PB3_RXDAT | PB3_CRS | PB3_COL | PB3_RXER | PB3_RXDV)
+#define PB3_DIRB1 (PB3_TXDAT | PB3_TXEN | PB3_TXER)
+#define PC3_DIRC1 (PC3_TXDAT)
+
+/* Handy macro to specify mem for FCCs*/
+#define FCC_MEM_OFFSET(x) (CPM_FCC_SPECIAL_BASE + (x*128))
+#define FCC1_MEM_OFFSET FCC_MEM_OFFSET(0)
+#define FCC2_MEM_OFFSET FCC_MEM_OFFSET(1)
+#define FCC2_MEM_OFFSET FCC_MEM_OFFSET(2)
+
#endif /* __CPM2__ */
#endif /* __KERNEL__ */
diff --git a/include/asm-ppc/mpc8260.h b/include/asm-ppc/mpc8260.h
index 6ba69a8..e4a897e 100644
--- a/include/asm-ppc/mpc8260.h
+++ b/include/asm-ppc/mpc8260.h
@@ -83,6 +83,7 @@ enum ppc_sys_devices {
MPC82xx_CPM_SMC2,
MPC82xx_CPM_USB,
MPC82xx_SEC1,
+ MPC82xx_MDIO_BB,
NUM_PPC_SYS_DEVS,
};
diff --git a/include/asm-ppc/mpc8xx.h b/include/asm-ppc/mpc8xx.h
index 3515a7f..8830dfe 100644
--- a/include/asm-ppc/mpc8xx.h
+++ b/include/asm-ppc/mpc8xx.h
@@ -111,6 +111,7 @@ enum ppc_sys_devices {
MPC8xx_CPM_SMC1,
MPC8xx_CPM_SMC2,
MPC8xx_CPM_USB,
+ MPC8xx_MDIO_FEC,
NUM_PPC_SYS_DEVS,
};
diff --git a/include/linux/fs_enet_pd.h b/include/linux/fs_enet_pd.h
index 783c476..74ed35a 100644
--- a/include/linux/fs_enet_pd.h
+++ b/include/linux/fs_enet_pd.h
@@ -69,36 +69,23 @@ enum fs_ioport {
fsiop_porte,
};
-struct fs_mii_bus_info {
- int method; /* mii method */
- int id; /* the id of the mii_bus */
- int disable_aneg; /* if the controller needs to negothiate speed & duplex */
- int lpa; /* the default board-specific vallues will be applied otherwise */
-
- union {
- struct {
- int duplex;
- int speed;
- } fixed;
-
- struct {
- /* nothing */
- } fec;
-
- struct {
- /* nothing */
- } scc;
-
- struct {
- int mdio_port; /* port & bit for MDIO */
- int mdio_bit;
- int mdc_port; /* port & bit for MDC */
- int mdc_bit;
- int delay; /* delay in us */
- } bitbang;
- } i;
-};
-
+struct fs_mii_bit {
+ u32 offset;
+ u8 bit;
+ u8 polarity;
+};
+struct fs_mii_bb_platform_info {
+ struct fs_mii_bit mdio_dir;
+ struct fs_mii_bit mdio_dat;
+ struct fs_mii_bit mdc_dat;
+ int mdio_port; /* port & bit for MDIO */
+ int mdio_bit;
+ int mdc_port; /* port & bit for MDC */
+ int mdc_bit;
+ int delay; /* delay in us */
+ int irq[32]; /* irqs per phy's */
+};
+
struct fs_platform_info {
void(*init_ioports)(void);
@@ -119,6 +106,7 @@ struct fs_platform_info {
u32 device_flags;
int phy_addr; /* the phy address (-1 no phy) */
+ const char* bus_id;
int phy_irq; /* the phy irq (if it exists) */
const struct fs_mii_bus_info *bus_info;
@@ -130,6 +118,10 @@ struct fs_platform_info {
int napi_weight; /* NAPI weight */
int use_rmii; /* use RMII mode */
+ int has_phy; /* if the network is phy container as well...*/
};
-
+struct fs_mii_fec_platform_info {
+ u32 irq[32];
+ u32 mii_speed;
+};
#endif
^ permalink raw reply related
* [PATCH 6/6] [RFC] POWERPC: Add mpc8560 board support
From: Vitaly Bordug @ 2006-06-23 23:17 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <20060623231648.6721.3495.stgit@localhost.localdomain>
This enables the mpc8560-specific bits in powerpc. The relevant cpm2 PIC
and common utility were moved without or with minor changes, hereby not all
the stuff have OF power utilized. Current functionality depends on the very
latest fs_enet update, that will go through netdev (cc'd here as
reference). Assuming all the preceeding stuff applied (PAL+fs_enet related
+ CPM_UART update), the both TSEC eth ,FCC Eths, and both SCC UARTs are
working. The relevant drivers are still capable to drive users in ppc,
which was verified with 8272ADS (SCC uart+FCC eth).
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
---
arch/powerpc/lib/Makefile | 5 +
arch/powerpc/platforms/85xx/Kconfig | 11 +
arch/powerpc/platforms/85xx/Makefile | 1
arch/powerpc/platforms/85xx/mpc8560_ads.h | 54 +++++
arch/powerpc/platforms/85xx/mpc85xx_ads.c | 107 +++++++++++
arch/powerpc/sysdev/Makefile | 7 +
arch/powerpc/sysdev/cpm2_common.c | 197 ++++++++++++++++++++
arch/powerpc/sysdev/cpm2_pic.c | 181 ++++++++++++++++++
arch/powerpc/sysdev/cpm2_pic.h | 8 +
arch/powerpc/sysdev/fsl_soc.c | 290 +++++++++++++++++++++++++++++
include/asm-ppc/cpm2.h | 2
11 files changed, 860 insertions(+), 3 deletions(-)
diff --git a/arch/powerpc/lib/Makefile b/arch/powerpc/lib/Makefile
index ff70964..0993b3b 100644
--- a/arch/powerpc/lib/Makefile
+++ b/arch/powerpc/lib/Makefile
@@ -21,3 +21,8 @@ ifeq ($(CONFIG_PPC64),y)
obj-$(CONFIG_SMP) += locks.o
obj-$(CONFIG_DEBUG_KERNEL) += sstep.o
endif
+
+# Temporary hack until we have migrated to asm-powerpc
+ifeq ($(ARCH),powerpc)
+obj-$(CONFIG_CPM2) += rheap.o
+endif
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index 454fc53..3d440de 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -11,6 +11,12 @@ config MPC8540_ADS
help
This option enables support for the MPC 8540 ADS board
+config MPC8560_ADS
+ bool "Freescale MPC8560 ADS"
+ select DEFAULT_UIMAGE
+ help
+ This option enables support for the MPC 8560 ADS board
+
config MPC85xx_CDS
bool "Freescale MPC85xx CDS"
select DEFAULT_UIMAGE
@@ -25,6 +31,11 @@ config MPC8540
select PPC_UDBG_16550
select PPC_INDIRECT_PCI
default y if MPC8540_ADS || MPC85xx_CDS
+
+config MPC8560
+ bool
+ select PPC_INDIRECT_PCI
+ default y if MPC8560_ADS
config PPC_INDIRECT_PCI_BE
bool
diff --git a/arch/powerpc/platforms/85xx/Makefile b/arch/powerpc/platforms/85xx/Makefile
index 7615aa5..282f5d0 100644
--- a/arch/powerpc/platforms/85xx/Makefile
+++ b/arch/powerpc/platforms/85xx/Makefile
@@ -3,4 +3,5 @@ # Makefile for the PowerPC 85xx linux ke
#
obj-$(CONFIG_PPC_85xx) += misc.o pci.o
obj-$(CONFIG_MPC8540_ADS) += mpc85xx_ads.o
+obj-$(CONFIG_MPC8560_ADS) += mpc85xx_ads.o
obj-$(CONFIG_MPC85xx_CDS) += mpc85xx_cds.o
diff --git a/arch/powerpc/platforms/85xx/mpc8560_ads.h b/arch/powerpc/platforms/85xx/mpc8560_ads.h
new file mode 100644
index 0000000..4ebe710
--- /dev/null
+++ b/arch/powerpc/platforms/85xx/mpc8560_ads.h
@@ -0,0 +1,54 @@
+/*
+ * MPC8560ADS board definitions
+ *
+ * Maintainer: Kumar Gala <galak@kernel.crashing.org>
+ *
+ * Copyright 2004 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#ifndef __MACH_MPC8560ADS_H
+#define __MACH_MPC8560ADS_H
+
+#include <linux/config.h>
+#include <linux/initrd.h>
+
+#define BOARD_CCSRBAR ((uint)0xe0000000)
+#define BCSR_ADDR ((uint)0xf8000000)
+#define BCSR_SIZE ((uint)(32 * 1024))
+
+#define MPC85xx_CPM_OFFSET (0x80000)
+
+/*XXX TODO: pull from OF*/
+#define CPM_MAP_ADDR (BOARD_CCSRBAR + MPC85xx_CPM_OFFSET)
+
+/* PCI interrupt controller */
+#define PIRQA MPC85xx_IRQ_EXT1
+#define PIRQB MPC85xx_IRQ_EXT2
+#define PIRQC MPC85xx_IRQ_EXT3
+#define PIRQD MPC85xx_IRQ_EXT4
+
+/* FCC1 Clock Source Configuration. These can be
+ * redefined in the board specific file.
+ * Can only choose from CLK9-12 */
+#define F1_RXCLK 12
+#define F1_TXCLK 11
+
+/* FCC2 Clock Source Configuration. These can be
+ * redefined in the board specific file.
+ * Can only choose from CLK13-16 */
+#define F2_RXCLK 13
+#define F2_TXCLK 14
+
+/* FCC3 Clock Source Configuration. These can be
+ * redefined in the board specific file.
+ * Can only choose from CLK13-16 */
+#define F3_RXCLK 15
+#define F3_TXCLK 16
+
+#endif /* __MACH_MPC8560ADS_H */
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_ads.c b/arch/powerpc/platforms/85xx/mpc85xx_ads.c
index 5eeff37..352d0ae 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_ads.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_ads.c
@@ -15,6 +15,7 @@ #include <linux/config.h>
#include <linux/stddef.h>
#include <linux/kernel.h>
#include <linux/pci.h>
+#include <linux/interrupt.h>
#include <linux/kdev_t.h>
#include <linux/delay.h>
#include <linux/seq_file.h>
@@ -30,6 +31,10 @@ #include <asm/mpic.h>
#include <mm/mmu_decl.h>
#include <asm/udbg.h>
+#ifdef CONFIG_CPM2
+#include <asm/cpm2.h>
+#endif
+
#include <sysdev/fsl_soc.h>
#include "mpc85xx.h"
@@ -121,8 +126,25 @@ mpc85xx_exclude_device(u_char bus, u_cha
}
#endif /* CONFIG_PCI */
+
+#ifdef CONFIG_CPM2
+static irqreturn_t cpm2_cascade(int irq, void *dev_id, struct pt_regs *regs)
+{
+ while ((irq = cpm2_get_irq(regs)) >= 0)
+ __do_IRQ(irq, regs);
+ return IRQ_HANDLED;
+}
+static struct irqaction cpm2_irqaction = {
+ .handler = cpm2_cascade,
+ .flags = SA_INTERRUPT,
+ .mask = CPU_MASK_NONE,
+ .name = "cpm2_cascade",
+};
+
+#endif /* CONFIG_CPM2 */
+
void __init mpc85xx_ads_pic_init(void)
{
struct mpic *mpic1;
@@ -158,15 +180,91 @@ void __init mpc85xx_ads_pic_init(void)
mpic_assign_isu(mpic1, 13, OpenPIC_PAddr + 0x10080);
mpic_assign_isu(mpic1, 14, OpenPIC_PAddr + 0x10100);
mpic_init(mpic1);
+
+#ifdef CONFIG_CPM2
+ /* Setup CPM2 PIC */
+
+ cpm2_init_IRQ();
+
+ setup_irq(MPC85xx_IRQ_CPM, &cpm2_irqaction);
+#endif
}
/*
* Setup the architecture
- */
+ */
+static void init_fcc_ioports(void)
+{
+ struct immap *immap;
+ struct io_port *io;
+ u32 tempval;
+
+ immap = cpm2_immr;
+
+ io = &immap->im_ioport;
+ /* FCC2/3 are on the ports B/C. */
+ tempval = in_be32(&io->iop_pdirb);
+ tempval &= ~PB2_DIRB0;
+ tempval |= PB2_DIRB1;
+ out_be32(&io->iop_pdirb, tempval);
+
+ tempval = in_be32(&io->iop_psorb);
+ tempval &= ~PB2_PSORB0;
+ tempval |= PB2_PSORB1;
+ out_be32(&io->iop_psorb, tempval);
+
+ tempval = in_be32(&io->iop_pparb);
+ tempval |= (PB2_DIRB0 | PB2_DIRB1);
+ out_be32(&io->iop_pparb, tempval);
+
+ tempval = in_be32(&io->iop_pdirb);
+ tempval &= ~PB3_DIRB0;
+ tempval |= PB3_DIRB1;
+ out_be32(&io->iop_pdirb, tempval);
+
+ tempval = in_be32(&io->iop_psorb);
+ tempval &= ~PB3_PSORB0;
+ tempval |= PB3_PSORB1;
+ out_be32(&io->iop_psorb, tempval);
+
+ tempval = in_be32(&io->iop_pparb);
+ tempval |= (PB3_DIRB0 | PB3_DIRB1);
+ out_be32(&io->iop_pparb, tempval);
+
+ tempval = in_be32(&io->iop_pdirc);
+ tempval |= PC3_DIRC1;
+ out_be32(&io->iop_pdirc, tempval);
+
+ tempval = in_be32(&io->iop_pparc);
+ tempval |= PC3_DIRC1;
+ out_be32(&io->iop_pparc, tempval);
+
+ /* Port C has clocks...... */
+ tempval = in_be32(&io->iop_psorc);
+ tempval &= ~(CLK_TRX);
+ out_be32(&io->iop_psorc, tempval);
+
+ tempval = in_be32(&io->iop_pdirc);
+ tempval &= ~(CLK_TRX);
+ out_be32(&io->iop_pdirc, tempval);
+ tempval = in_be32(&io->iop_pparc);
+ tempval |= (CLK_TRX);
+ out_be32(&io->iop_pparc, tempval);
+
+ /* Configure Serial Interface clock routing.
+ * First, clear all FCC bits to zero,
+ * then set the ones we want.
+ */
+ immap->im_cpmux.cmx_fcr &= ~(CPMUX_CLK_MASK);
+ immap->im_cpmux.cmx_fcr |= CPMUX_CLK_ROUTE;
+}
+
static void __init mpc85xx_ads_setup_arch(void)
{
struct device_node *cpu;
struct device_node *np;
+
+ cpm2_reset();
if (ppc_md.progress)
ppc_md.progress("mpc85xx_ads_setup_arch()", 0);
@@ -184,8 +282,13 @@ static void __init mpc85xx_ads_setup_arc
}
#ifdef CONFIG_PCI
+
for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;)
add_bridge(np);
+
+#ifdef CONFIG_CPM2
+ init_fcc_ioports();
+#endif
ppc_md.pci_swizzle = common_swizzle;
ppc_md.pci_map_irq = mpc85xx_map_irq;
@@ -240,5 +343,7 @@ define_machine(mpc85xx_ads) {
.get_irq = mpic_get_irq,
.restart = mpc85xx_restart,
.calibrate_decr = generic_calibrate_decr,
+#ifndef CONFIG_CPM2
.progress = udbg_progress,
+#endif
};
diff --git a/arch/powerpc/sysdev/Makefile b/arch/powerpc/sysdev/Makefile
index cef95b0..75dfe12 100644
--- a/arch/powerpc/sysdev/Makefile
+++ b/arch/powerpc/sysdev/Makefile
@@ -12,3 +12,10 @@ obj-$(CONFIG_U3_DART) += dart_iommu.o
obj-$(CONFIG_MMIO_NVRAM) += mmio_nvram.o
obj-$(CONFIG_PPC_83xx) += ipic.o
obj-$(CONFIG_FSL_SOC) += fsl_soc.o
+
+# Temporary hack until we have migrated to asm-powerpc
+ifeq ($(ARCH),powerpc)
+obj-$(CONFIG_CPM2) += cpm2_common.o cpm2_pic.o
+endif
+
+#obj-$(CONFIG_CPM2) += cpm2/ Yuri
diff --git a/arch/powerpc/sysdev/cpm2_common.c b/arch/powerpc/sysdev/cpm2_common.c
new file mode 100644
index 0000000..c755f65
--- /dev/null
+++ b/arch/powerpc/sysdev/cpm2_common.c
@@ -0,0 +1,197 @@
+/*
+ * General Purpose functions for the global management of the
+ * 8260 Communication Processor Module.
+ * Copyright (c) 1999 Dan Malek (dmalek@jlc.net)
+ * Copyright (c) 2000 MontaVista Software, Inc (source@mvista.com)
+ * 2.3.99 Updates
+ *
+ * In addition to the individual control of the communication
+ * channels, there are a few functions that globally affect the
+ * communication processor.
+ *
+ * Buffer descriptors must be allocated from the dual ported memory
+ * space. The allocator for that is here. When the communication
+ * process is reset, we reclaim the memory available. There is
+ * currently no deallocator for this memory.
+ */
+#include <linux/errno.h>
+#include <linux/sched.h>
+#include <linux/kernel.h>
+#include <linux/param.h>
+#include <linux/string.h>
+#include <linux/mm.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/mpc8260.h>
+#include <asm/page.h>
+#include <asm/pgtable.h>
+#include <asm/cpm2.h>
+#include <asm/rheap.h>
+
+static void cpm2_dpinit(void);
+cpm_cpm2_t *cpmp; /* Pointer to comm processor space */
+
+/* We allocate this here because it is used almost exclusively for
+ * the communication processor devices.
+ */
+cpm2_map_t *cpm2_immr;
+
+#define CPM_MAP_SIZE (0x40000) /* 256k - the PQ3 reserve this amount
+ of space for CPM as it is larger
+ than on PQ2 */
+
+void
+cpm2_reset(void)
+{
+ cpm2_immr = (cpm2_map_t *)ioremap(CPM_MAP_ADDR, CPM_MAP_SIZE);
+
+ /* Reclaim the DP memory for our use.
+ */
+ cpm2_dpinit();
+
+ /* Tell everyone where the comm processor resides.
+ */
+ cpmp = &cpm2_immr->im_cpm;
+}
+
+/* Set a baud rate generator. This needs lots of work. There are
+ * eight BRGs, which can be connected to the CPM channels or output
+ * as clocks. The BRGs are in two different block of internal
+ * memory mapped space.
+ * The baud rate clock is the system clock divided by something.
+ * It was set up long ago during the initial boot phase and is
+ * is given to us.
+ * Baud rate clocks are zero-based in the driver code (as that maps
+ * to port numbers). Documentation uses 1-based numbering.
+ */
+#define BRG_INT_CLK (get_brgfreq())
+#define BRG_UART_CLK (BRG_INT_CLK/16)
+
+/* This function is used by UARTS, or anything else that uses a 16x
+ * oversampled clock.
+ */
+void
+cpm_setbrg(uint brg, uint rate)
+{
+ volatile uint *bp;
+
+ /* This is good enough to get SMCs running.....
+ */
+ if (brg < 4) {
+ bp = (uint *)&cpm2_immr->im_brgc1;
+ }
+ else {
+ bp = (uint *)&cpm2_immr->im_brgc5;
+ brg -= 4;
+ }
+ bp += brg;
+ *bp = ((BRG_UART_CLK / rate) << 1) | CPM_BRG_EN;
+}
+
+/* This function is used to set high speed synchronous baud rate
+ * clocks.
+ */
+void
+cpm2_fastbrg(uint brg, uint rate, int div16)
+{
+ volatile uint *bp;
+
+ if (brg < 4) {
+ bp = (uint *)&cpm2_immr->im_brgc1;
+ }
+ else {
+ bp = (uint *)&cpm2_immr->im_brgc5;
+ brg -= 4;
+ }
+ bp += brg;
+ *bp = ((BRG_INT_CLK / rate) << 1) | CPM_BRG_EN;
+ if (div16)
+ *bp |= CPM_BRG_DIV16;
+}
+
+/*
+ * dpalloc / dpfree bits.
+ */
+static spinlock_t cpm_dpmem_lock;
+/* 16 blocks should be enough to satisfy all requests
+ * until the memory subsystem goes up... */
+static rh_block_t cpm_boot_dpmem_rh_block[16];
+static rh_info_t cpm_dpmem_info;
+
+static void cpm2_dpinit(void)
+{
+ spin_lock_init(&cpm_dpmem_lock);
+
+ /* initialize the info header */
+ rh_init(&cpm_dpmem_info, 1,
+ sizeof(cpm_boot_dpmem_rh_block) /
+ sizeof(cpm_boot_dpmem_rh_block[0]),
+ cpm_boot_dpmem_rh_block);
+
+ /* Attach the usable dpmem area */
+ /* XXX: This is actually crap. CPM_DATAONLY_BASE and
+ * CPM_DATAONLY_SIZE is only a subset of the available dpram. It
+ * varies with the processor and the microcode patches activated.
+ * But the following should be at least safe.
+ */
+ rh_attach_region(&cpm_dpmem_info, (void *)CPM_DATAONLY_BASE,
+ CPM_DATAONLY_SIZE);
+}
+
+/* This function returns an index into the DPRAM area.
+ */
+uint cpm_dpalloc(uint size, uint align)
+{
+ void *start;
+ unsigned long flags;
+
+ spin_lock_irqsave(&cpm_dpmem_lock, flags);
+ cpm_dpmem_info.alignment = align;
+ start = rh_alloc(&cpm_dpmem_info, size, "commproc");
+ spin_unlock_irqrestore(&cpm_dpmem_lock, flags);
+
+ return (uint)start;
+}
+EXPORT_SYMBOL(cpm_dpalloc);
+
+int cpm_dpfree(uint offset)
+{
+ int ret;
+ unsigned long flags;
+
+ spin_lock_irqsave(&cpm_dpmem_lock, flags);
+ ret = rh_free(&cpm_dpmem_info, (void *)offset);
+ spin_unlock_irqrestore(&cpm_dpmem_lock, flags);
+
+ return ret;
+}
+EXPORT_SYMBOL(cpm_dpfree);
+
+/* not sure if this is ever needed */
+uint cpm_dpalloc_fixed(uint offset, uint size, uint align)
+{
+ void *start;
+ unsigned long flags;
+
+ spin_lock_irqsave(&cpm_dpmem_lock, flags);
+ cpm_dpmem_info.alignment = align;
+ start = rh_alloc_fixed(&cpm_dpmem_info, (void *)offset, size, "commproc");
+ spin_unlock_irqrestore(&cpm_dpmem_lock, flags);
+
+ return (uint)start;
+}
+EXPORT_SYMBOL(cpm_dpalloc_fixed);
+
+void cpm_dpdump(void)
+{
+ rh_dump(&cpm_dpmem_info);
+}
+EXPORT_SYMBOL(cpm_dpdump);
+
+void *cpm_dpram_addr(uint offset)
+{
+ return (void *)&cpm2_immr->im_dprambase[offset];
+}
+EXPORT_SYMBOL(cpm_dpram_addr);
diff --git a/arch/powerpc/sysdev/cpm2_pic.c b/arch/powerpc/sysdev/cpm2_pic.c
new file mode 100644
index 0000000..e0db594
--- /dev/null
+++ b/arch/powerpc/sysdev/cpm2_pic.c
@@ -0,0 +1,181 @@
+/* The CPM2 internal interrupt controller. It is usually
+ * the only interrupt controller.
+ * There are two 32-bit registers (high/low) for up to 64
+ * possible interrupts.
+ *
+ * Now, the fun starts.....Interrupt Numbers DO NOT MAP
+ * in a simple arithmetic fashion to mask or pending registers.
+ * That is, interrupt 4 does not map to bit position 4.
+ * We create two tables, indexed by vector number, to indicate
+ * which register to use and which bit in the register to use.
+ */
+
+#include <linux/stddef.h>
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/signal.h>
+#include <linux/irq.h>
+
+#include <asm/immap_cpm2.h>
+#include <asm/mpc8260.h>
+#include <asm/io.h>
+
+#include "cpm2_pic.h"
+
+static u_char irq_to_siureg[] = {
+ 1, 1, 1, 1, 1, 1, 1, 1,
+ 1, 1, 1, 1, 1, 1, 1, 1,
+ 0, 0, 0, 0, 0, 0, 0, 0,
+ 0, 0, 0, 0, 0, 0, 0, 0,
+ 1, 1, 1, 1, 1, 1, 1, 1,
+ 1, 1, 1, 1, 1, 1, 1, 1,
+ 0, 0, 0, 0, 0, 0, 0, 0,
+ 0, 0, 0, 0, 0, 0, 0, 0
+};
+
+/* bit numbers do not match the docs, these are precomputed so the bit for
+ * a given irq is (1 << irq_to_siubit[irq]) */
+static u_char irq_to_siubit[] = {
+ 0, 15, 14, 13, 12, 11, 10, 9,
+ 8, 7, 6, 5, 4, 3, 2, 1,
+ 2, 1, 0, 14, 13, 12, 11, 10,
+ 9, 8, 7, 6, 5, 4, 3, 0,
+ 31, 30, 29, 28, 27, 26, 25, 24,
+ 23, 22, 21, 20, 19, 18, 17, 16,
+ 16, 17, 18, 19, 20, 21, 22, 23,
+ 24, 25, 26, 27, 28, 29, 30, 31,
+};
+
+static void cpm2_mask_irq(unsigned int irq_nr)
+{
+ int bit, word;
+ volatile uint *simr;
+
+ irq_nr -= CPM_IRQ_OFFSET;
+
+ bit = irq_to_siubit[irq_nr];
+ word = irq_to_siureg[irq_nr];
+
+ simr = &(cpm2_immr->im_intctl.ic_simrh);
+ ppc_cached_irq_mask[word] &= ~(1 << bit);
+ simr[word] = ppc_cached_irq_mask[word];
+}
+
+static void cpm2_unmask_irq(unsigned int irq_nr)
+{
+ int bit, word;
+ volatile uint *simr;
+
+ irq_nr -= CPM_IRQ_OFFSET;
+
+ bit = irq_to_siubit[irq_nr];
+ word = irq_to_siureg[irq_nr];
+
+ simr = &(cpm2_immr->im_intctl.ic_simrh);
+ ppc_cached_irq_mask[word] |= 1 << bit;
+ simr[word] = ppc_cached_irq_mask[word];
+}
+
+static void cpm2_mask_and_ack(unsigned int irq_nr)
+{
+ int bit, word;
+ volatile uint *simr, *sipnr;
+
+ irq_nr -= CPM_IRQ_OFFSET;
+
+ bit = irq_to_siubit[irq_nr];
+ word = irq_to_siureg[irq_nr];
+
+ simr = &(cpm2_immr->im_intctl.ic_simrh);
+ sipnr = &(cpm2_immr->im_intctl.ic_sipnrh);
+ ppc_cached_irq_mask[word] &= ~(1 << bit);
+ simr[word] = ppc_cached_irq_mask[word];
+ sipnr[word] = 1 << bit;
+}
+
+static void cpm2_end_irq(unsigned int irq_nr)
+{
+ int bit, word;
+ volatile uint *simr;
+
+ if (!(irq_desc[irq_nr].status & (IRQ_DISABLED|IRQ_INPROGRESS))
+ && irq_desc[irq_nr].action) {
+
+ irq_nr -= CPM_IRQ_OFFSET;
+ bit = irq_to_siubit[irq_nr];
+ word = irq_to_siureg[irq_nr];
+
+ simr = &(cpm2_immr->im_intctl.ic_simrh);
+ ppc_cached_irq_mask[word] |= 1 << bit;
+ simr[word] = ppc_cached_irq_mask[word];
+ /*
+ * Work around large numbers of spurious IRQs on PowerPC 82xx
+ * systems.
+ */
+ mb();
+ }
+}
+
+static struct hw_interrupt_type cpm2_pic = {
+ .typename = " CPM2 SIU ",
+ .enable = cpm2_unmask_irq,
+ .disable = cpm2_mask_irq,
+ .ack = cpm2_mask_and_ack,
+ .end = cpm2_end_irq,
+};
+
+int cpm2_get_irq(struct pt_regs *regs)
+{
+ int irq;
+ unsigned long bits;
+
+ /* For CPM2, read the SIVEC register and shift the bits down
+ * to get the irq number. */
+ bits = cpm2_immr->im_intctl.ic_sivec;
+ irq = bits >> 26;
+
+ if (irq == 0)
+ return(-1);
+ return irq+CPM_IRQ_OFFSET;
+}
+
+void cpm2_init_IRQ(void)
+{
+ int i;
+ u32 addr;
+
+ /* Clear the CPM IRQ controller, in case it has any bits set
+ * from the bootloader
+ */
+
+ /* Mask out everything */
+
+ cpm2_immr->im_intctl.ic_simrh = 0x00000000;
+ cpm2_immr->im_intctl.ic_simrl = 0x00000000;
+
+ wmb();
+
+ /* Ack everything */
+ cpm2_immr->im_intctl.ic_sipnrh = 0xffffffff;
+ cpm2_immr->im_intctl.ic_sipnrl = 0xffffffff;
+ wmb();
+
+ /* Dummy read of the vector */
+ i = cpm2_immr->im_intctl.ic_sivec;
+ rmb();
+
+ /* Initialize the default interrupt mapping priorities,
+ * in case the boot rom changed something on us.
+ */
+ cpm2_immr->im_intctl.ic_sicr = 0;
+ cpm2_immr->im_intctl.ic_scprrh = 0x05309770;
+ cpm2_immr->im_intctl.ic_scprrl = 0x05309770;
+
+
+ /* Enable chaining to OpenPIC, and make everything level
+ */
+ for (i = 0; i < NR_CPM_INTS; i++) {
+ irq_desc[i+CPM_IRQ_OFFSET].handler = &cpm2_pic;
+ irq_desc[i+CPM_IRQ_OFFSET].status |= IRQ_LEVEL;
+ }
+}
diff --git a/arch/powerpc/sysdev/cpm2_pic.h b/arch/powerpc/sysdev/cpm2_pic.h
new file mode 100644
index 0000000..97cab8f
--- /dev/null
+++ b/arch/powerpc/sysdev/cpm2_pic.h
@@ -0,0 +1,8 @@
+#ifndef _PPC_KERNEL_CPM2_H
+#define _PPC_KERNEL_CPM2_H
+
+extern int cpm2_get_irq(struct pt_regs *regs);
+
+extern void cpm2_init_IRQ(void);
+
+#endif /* _PPC_KERNEL_CPM2_H */
diff --git a/arch/powerpc/sysdev/fsl_soc.c b/arch/powerpc/sysdev/fsl_soc.c
index ceb5846..bab202d 100644
--- a/arch/powerpc/sysdev/fsl_soc.c
+++ b/arch/powerpc/sysdev/fsl_soc.c
@@ -21,6 +21,8 @@ #include <linux/module.h>
#include <linux/device.h>
#include <linux/platform_device.h>
#include <linux/fsl_devices.h>
+#include <linux/fs_enet_pd.h>
+#include <linux/fs_uart_pd.h>
#include <asm/system.h>
#include <asm/atomic.h>
@@ -30,6 +32,10 @@ #include <asm/prom.h>
#include <sysdev/fsl_soc.h>
#include <mm/mmu_decl.h>
+#ifdef CONFIG_CPM2
+#include <asm/cpm2.h>
+#endif
+
static phys_addr_t immrbase = -1;
phys_addr_t get_immrbase(void)
@@ -43,7 +49,9 @@ phys_addr_t get_immrbase(void)
if (soc) {
unsigned int size;
void *prop = get_property(soc, "reg", &size);
- immrbase = of_translate_address(soc, prop);
+
+ if (prop)
+ immrbase = of_translate_address(soc, prop);
of_node_put(soc);
};
@@ -51,7 +59,79 @@ phys_addr_t get_immrbase(void)
}
EXPORT_SYMBOL(get_immrbase);
+
+static u32 brgfreq = -1;
+
+u32 get_brgfreq(void)
+{
+ struct device_node *node;
+
+ if (brgfreq != -1)
+ return brgfreq;
+
+ node = of_find_node_by_type(NULL, "serial");
+ if (node) {
+ unsigned int size;
+ unsigned int *prop = (unsigned int*)get_property(node, "clock-frequency", &size);
+
+ if (prop)
+ brgfreq = *prop;
+ of_node_put(node);
+ };
+
+ return brgfreq;
+}
+
+EXPORT_SYMBOL(get_brgfreq);
+
+static u32 fs_baudrate = -1;
+
+u32 get_baudrate(void)
+{
+ struct device_node *node;
+ if (fs_baudrate != -1)
+ return fs_baudrate;
+
+ node = of_find_node_by_type(NULL, "serial");
+ if (node) {
+ unsigned int size;
+ unsigned int *prop = (unsigned int*)get_property(node, "current-speed", &size);
+
+ if (prop)
+ fs_baudrate = *prop;
+ of_node_put(node);
+ };
+
+ return fs_baudrate;
+}
+
+EXPORT_SYMBOL(get_baudrate);
+
+static u32 intfreq = -1;
+
+u32 get_intfreq(void)
+{
+ struct device_node *node;
+
+ if (intfreq != -1)
+ return intfreq;
+
+ node = of_find_node_by_type(NULL, "cpu");
+ if (node) {
+ unsigned int size;
+ unsigned int *prop = (unsigned int*)get_property(node, "clock-frequency", &size);
+ if (prop)
+ intfreq = *prop;
+ of_node_put(node);
+ }
+
+ return intfreq;
+}
+
+EXPORT_SYMBOL(get_intfreq);
+
+
static int __init gfar_mdio_of_init(void)
{
struct device_node *np;
@@ -491,3 +571,211 @@ err:
}
arch_initcall(fsl_usb_dr_of_init);
+
+static const char *fcc_regs = "fcc_regs";
+static const char *fcc_regs_c = "fcc_regs_c";
+static const char *fcc_pram = "fcc_pram";
+static char bus_id[9][BUS_ID_SIZE];
+
+static int __init fs_enet_of_init(void)
+{
+ struct device_node *np;
+ unsigned int i;
+ struct platform_device *fs_enet_dev;
+ struct resource res;
+ int ret;
+
+ for (np = NULL, i = 0;
+ (np = of_find_compatible_node(np, "network", "fs_enet")) != NULL;
+ i++) {
+ struct resource r[4];
+ struct device_node *phy, *mdio;
+ struct fs_platform_info fs_enet_data;
+ unsigned int *id, *phy_addr;
+ void *mac_addr;
+ phandle *ph;
+ char *model;
+
+ memset(r, 0, sizeof(r));
+ memset(&fs_enet_data, 0, sizeof(fs_enet_data));
+
+ ret = of_address_to_resource(np, 0, &r[0]);
+ if (ret)
+ goto err;
+ r[0].name = fcc_regs;
+
+ ret = of_address_to_resource(np, 1, &r[1]);
+ if (ret)
+ goto err;
+ r[1].name = fcc_pram;
+
+ ret = of_address_to_resource(np, 2, &r[2]);
+ if (ret)
+ goto err;
+ r[2].name = fcc_regs_c;
+
+ r[3].start = np->intrs[0].line;
+ r[3].end = np->intrs[0].line;
+ r[3].flags = IORESOURCE_IRQ;
+
+ fs_enet_dev =
+ platform_device_register_simple("fsl-cpm-fcc", i, &r[0], 4);
+
+ if (IS_ERR(fs_enet_dev)) {
+ ret = PTR_ERR(fs_enet_dev);
+ goto err;
+ }
+
+ model = get_property(np, "model", NULL);
+ if (model == NULL) {
+ ret = -ENODEV;
+ goto unreg;
+ }
+
+ mac_addr = get_property(np, "mac-address", NULL);
+ memcpy(fs_enet_data.macaddr, mac_addr, 6);
+
+ ph = (phandle *) get_property(np, "phy-handle", NULL);
+ phy = of_find_node_by_phandle(*ph);
+
+ if (phy == NULL) {
+ ret = -ENODEV;
+ goto unreg;
+ }
+
+ phy_addr = (u32 *) get_property(phy, "reg", NULL);
+ fs_enet_data.phy_addr = *phy_addr;
+
+ id = (u32 *) get_property(np, "device-id", NULL);
+ fs_enet_data.fs_no = *id;
+
+ mdio = of_get_parent(phy);
+ ret = of_address_to_resource(mdio, 0, &res);
+ if (ret) {
+ of_node_put(phy);
+ of_node_put(mdio);
+ goto unreg;
+ }
+
+ switch (*id) {
+ case fsid_fcc1:
+ fs_enet_data.mem_offset = FCC1_MEM_OFFSET,
+ snprintf((char*)&bus_id[2], BUS_ID_SIZE, "%x:%02x", (u32)res.start, fs_enet_data.phy_addr);
+ fs_enet_data.bus_id = (char*)&bus_id[2];
+ fs_enet_data.cp_page = CPM_CR_FCC1_PAGE;
+ fs_enet_data.cp_block = CPM_CR_FCC1_SBLOCK;
+ break;
+ case fsid_fcc2:
+ fs_enet_data.mem_offset = FCC2_MEM_OFFSET,
+ snprintf((char*)&bus_id[3], BUS_ID_SIZE, "%x:%02x", (u32)res.start, fs_enet_data.phy_addr);
+ fs_enet_data.bus_id = (char*)&bus_id[3];
+ fs_enet_data.cp_page = CPM_CR_FCC2_PAGE;
+ fs_enet_data.cp_block = CPM_CR_FCC2_SBLOCK;
+ break;
+ case fsid_fcc3:
+ fs_enet_data.mem_offset = FCC3_MEM_OFFSET,
+ snprintf((char*)&bus_id[4], BUS_ID_SIZE, "%x:%02x", (u32)res.start, fs_enet_data.phy_addr);
+ fs_enet_data.bus_id = (char*)&bus_id[4];
+ fs_enet_data.cp_page = CPM_CR_FCC3_PAGE;
+ fs_enet_data.cp_block = CPM_CR_FCC3_SBLOCK;
+ break;
+ }
+
+ if (strstr(model, "FCC")) {
+ fs_enet_data.dpram_offset = (u32)cpm2_immr->im_dprambase;
+ fs_enet_data.rx_ring = 32;
+ fs_enet_data.tx_ring = 32;
+ fs_enet_data.rx_copybreak = 240;
+ fs_enet_data.use_napi = 0;
+ fs_enet_data.napi_weight = 17;
+ }
+
+ of_node_put(phy);
+ of_node_put(mdio);
+
+ ret = platform_device_add_data(fs_enet_dev, &fs_enet_data,
+ sizeof(struct
+ fs_platform_info));
+ if (ret)
+ goto unreg;
+ }
+ return 0;
+
+unreg:
+ platform_device_unregister(fs_enet_dev);
+err:
+ return ret;
+}
+
+arch_initcall(fs_enet_of_init);
+
+static const char *scc_regs = "regs";
+static const char *scc_pram = "pram";
+
+static int __init cpm_uart_of_init(void)
+{
+ struct device_node *np;
+ unsigned int i;
+ struct platform_device *cpm_uart_dev;
+ int ret;
+
+
+ for (np = NULL, i = 0;
+ (np = of_find_compatible_node(np, "serial", "cpm_uart")) != NULL;
+ i++) {
+ struct resource r[3];
+ struct fs_uart_platform_info cpm_uart_data;
+ int *id;
+
+ memset(r, 0, sizeof(r));
+ memset(&cpm_uart_data, 0, sizeof(cpm_uart_data));
+
+ ret = of_address_to_resource(np, 0, &r[0]);
+ if (ret)
+ goto err;
+
+ r[0].name = scc_regs;
+
+ ret = of_address_to_resource(np, 1, &r[1]);
+ if (ret)
+ goto err;
+ r[1].name = scc_pram;
+
+ r[2].start = np->intrs[0].line;
+ r[2].end = np->intrs[0].line;
+ r[2].flags = IORESOURCE_IRQ;
+
+ cpm_uart_dev =
+ platform_device_register_simple("fsl-cpm-scc:uart", i, &r[0], 3);
+
+ if (IS_ERR(cpm_uart_dev)) {
+ ret = PTR_ERR(cpm_uart_dev);
+ goto err;
+ }
+
+ id = get_property(np, "device-id", NULL);
+ cpm_uart_data.fs_no = *id;
+ cpm_uart_data.uart_clk = get_intfreq();
+
+ cpm_uart_data.tx_num_fifo = 4;
+ cpm_uart_data.tx_buf_size = 32;
+ cpm_uart_data.rx_num_fifo = 4;
+ cpm_uart_data.rx_buf_size = 32;
+
+ ret =
+ platform_device_add_data(cpm_uart_dev, &cpm_uart_data,
+ sizeof(struct
+ fs_uart_platform_info));
+ if (ret)
+ goto unreg;
+ }
+
+ return 0;
+
+unreg:
+ platform_device_unregister(cpm_uart_dev);
+err:
+ return ret;
+}
+
+arch_initcall(cpm_uart_of_init);
diff --git a/include/asm-ppc/cpm2.h b/include/asm-ppc/cpm2.h
index f6a7ff0..8e6840b 100644
--- a/include/asm-ppc/cpm2.h
+++ b/include/asm-ppc/cpm2.h
@@ -1186,7 +1186,7 @@ #define PC3_DIRC1 (PC3_TXDAT)
#define FCC_MEM_OFFSET(x) (CPM_FCC_SPECIAL_BASE + (x*128))
#define FCC1_MEM_OFFSET FCC_MEM_OFFSET(0)
#define FCC2_MEM_OFFSET FCC_MEM_OFFSET(1)
-#define FCC2_MEM_OFFSET FCC_MEM_OFFSET(2)
+#define FCC3_MEM_OFFSET FCC_MEM_OFFSET(2)
#endif /* __CPM2__ */
#endif /* __KERNEL__ */
^ permalink raw reply related
* [PATCH 5/6] CPM_UART: unify clock sources
From: Vitaly Bordug @ 2006-06-23 23:17 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <20060623231648.6721.3495.stgit@localhost.localdomain>
In order to make it possible to utilize the driver from arch/powerpc yet not
breaking existing ppc users, clock sources are unfied via macro, and
resources ioremapped.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
---
drivers/serial/cpm_uart/cpm_uart_core.c | 11 ++++-------
drivers/serial/cpm_uart/cpm_uart_cpm2.c | 13 +++++++------
include/asm-powerpc/fs_pd.h | 17 +++++++++++++++++
include/asm-ppc/fs_pd.h | 17 +++++++++++++++++
4 files changed, 45 insertions(+), 13 deletions(-)
diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c b/drivers/serial/cpm_uart/cpm_uart_core.c
index 5cba59a..0507f74 100644
--- a/drivers/serial/cpm_uart/cpm_uart_core.c
+++ b/drivers/serial/cpm_uart/cpm_uart_core.c
@@ -47,6 +47,7 @@ #include <linux/fs_uart_pd.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/delay.h>
+#include <asm/fs_pd.h>
#if defined(CONFIG_SERIAL_CPM_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
@@ -1045,11 +1046,11 @@ int cpm_uart_drv_get_platform_data(struc
if (!(r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "regs")))
return -EINVAL;
- mem = r->start;
+ mem = ioremap(r->start, r->end - r->start + 1);
if (!(r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pram")))
return -EINVAL;
- pram = r->start;
+ pram = ioremap(r->start, r->end - r->start + 1);
if(idx > fsid_smc2_uart) {
pinfo->sccp = (scc_t *)mem;
@@ -1190,11 +1191,7 @@ static int __init cpm_uart_console_setup
if (options) {
uart_parse_options(options, &baud, &parity, &bits, &flow);
} else {
- bd_t *bd = (bd_t *) __res;
-
- if (bd->bi_baudrate)
- baud = bd->bi_baudrate;
- else
+ if ((baud = GET_BAUDRATE()) == -1)
baud = 9600;
}
diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm2.c b/drivers/serial/cpm_uart/cpm_uart_cpm2.c
index cdba128..29b89f0 100644
--- a/drivers/serial/cpm_uart/cpm_uart_cpm2.c
+++ b/drivers/serial/cpm_uart/cpm_uart_cpm2.c
@@ -41,6 +41,7 @@ #include <linux/dma-mapping.h>
#include <asm/io.h>
#include <asm/irq.h>
+#include <asm/fs_pd.h>
#include <linux/serial_core.h>
#include <linux/kernel.h>
@@ -267,7 +268,7 @@ #ifdef CONFIG_SERIAL_CPM_SMC1
(unsigned long)&cpm2_immr->im_smc[0];
cpm_uart_ports[UART_SMC1].smcp->smc_smcm |= (SMCM_RX | SMCM_TX);
cpm_uart_ports[UART_SMC1].smcp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
- cpm_uart_ports[UART_SMC1].port.uartclk = (((bd_t *) __res)->bi_intfreq);
+ cpm_uart_ports[UART_SMC1].port.uartclk = FS_UART_CLK();
cpm_uart_port_map[cpm_uart_nr++] = UART_SMC1;
#endif
@@ -280,7 +281,7 @@ #ifdef CONFIG_SERIAL_CPM_SMC2
(unsigned long)&cpm2_immr->im_smc[1];
cpm_uart_ports[UART_SMC2].smcp->smc_smcm |= (SMCM_RX | SMCM_TX);
cpm_uart_ports[UART_SMC2].smcp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
- cpm_uart_ports[UART_SMC2].port.uartclk = (((bd_t *) __res)->bi_intfreq);
+ cpm_uart_ports[UART_SMC2].port.uartclk = FS_UART_CLK();
cpm_uart_port_map[cpm_uart_nr++] = UART_SMC2;
#endif
@@ -294,7 +295,7 @@ #ifdef CONFIG_SERIAL_CPM_SCC1
~(UART_SCCM_TX | UART_SCCM_RX);
cpm_uart_ports[UART_SCC1].sccp->scc_gsmrl &=
~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
- cpm_uart_ports[UART_SCC1].port.uartclk = (((bd_t *) __res)->bi_intfreq);
+ cpm_uart_ports[UART_SCC1].port.uartclk = FS_UART_CLK();
cpm_uart_port_map[cpm_uart_nr++] = UART_SCC1;
#endif
@@ -308,7 +309,7 @@ #ifdef CONFIG_SERIAL_CPM_SCC2
~(UART_SCCM_TX | UART_SCCM_RX);
cpm_uart_ports[UART_SCC2].sccp->scc_gsmrl &=
~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
- cpm_uart_ports[UART_SCC2].port.uartclk = (((bd_t *) __res)->bi_intfreq);
+ cpm_uart_ports[UART_SCC2].port.uartclk = FS_UART_CLK();
cpm_uart_port_map[cpm_uart_nr++] = UART_SCC2;
#endif
@@ -322,7 +323,7 @@ #ifdef CONFIG_SERIAL_CPM_SCC3
~(UART_SCCM_TX | UART_SCCM_RX);
cpm_uart_ports[UART_SCC3].sccp->scc_gsmrl &=
~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
- cpm_uart_ports[UART_SCC3].port.uartclk = (((bd_t *) __res)->bi_intfreq);
+ cpm_uart_ports[UART_SCC3].port.uartclk = FS_UART_CLK();
cpm_uart_port_map[cpm_uart_nr++] = UART_SCC3;
#endif
@@ -336,7 +337,7 @@ #ifdef CONFIG_SERIAL_CPM_SCC4
~(UART_SCCM_TX | UART_SCCM_RX);
cpm_uart_ports[UART_SCC4].sccp->scc_gsmrl &=
~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
- cpm_uart_ports[UART_SCC4].port.uartclk = (((bd_t *) __res)->bi_intfreq);
+ cpm_uart_ports[UART_SCC4].port.uartclk = FS_UART_CLK();
cpm_uart_port_map[cpm_uart_nr++] = UART_SCC4;
#endif
diff --git a/include/asm-powerpc/fs_pd.h b/include/asm-powerpc/fs_pd.h
new file mode 100644
index 0000000..b20d8da
--- /dev/null
+++ b/include/asm-powerpc/fs_pd.h
@@ -0,0 +1,17 @@
+/*
+ * Platform information definitions.
+ *
+ * 2006 (c) MontaVista Software, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#ifndef FS_PD_H
+#define FS_PD_H
+
+#define GET_BAUDRATE() get_baudrate()
+#define FS_UART_CLK() get_intfreq()
+
+#endif
diff --git a/include/asm-ppc/fs_pd.h b/include/asm-ppc/fs_pd.h
new file mode 100644
index 0000000..b1d550b
--- /dev/null
+++ b/include/asm-ppc/fs_pd.h
@@ -0,0 +1,17 @@
+/*
+ * Platform information definitions.
+ *
+ * 2006 (c) MontaVista Software, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#ifndef FS_PD_H
+#define FS_PD_H
+
+#define GET_BAUDRATE() (((bd_t *) __res)->bi_baudrate ? ((bd_t *) __res)->bi_baudrate : -1)
+#define FS_UART_CLK() (((bd_t *) __res)->bi_intfreq)
+
+#endif
^ permalink raw reply related
* [PATCH 1/6] PAL: Support of the fixed PHY
From: Vitaly Bordug @ 2006-06-23 23:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <20060623231648.6721.3495.stgit@localhost.localdomain>
This makes it possible for HW PHY-less boards to utilize PAL goodies.
Generic routines to connect to fixed PHY are provided, as well as ability
to specify software callback that fills up link, speed, etc. information
into PHY descriptor (the latter feature not tested so far).
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
---
drivers/net/phy/Kconfig | 17 ++++++++++++++
drivers/net/phy/phy_device.c | 51 +++++++++++++++++++++++++-----------------
include/linux/phy.h | 1 +
3 files changed, 48 insertions(+), 21 deletions(-)
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 76e51b1..e977fe1 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -50,5 +50,22 @@ config VITESSE_PHY
---help---
Currently supports the vsc8244
+config FIXED_PHY
+ tristate "Drivers for PHY emulation on fixed speed/link"
+ depends on PHYLIB
+ ---help---
+ Adds the driver to PHY layer to cover the boards that do not have any PHY bound,
+ but with the ability to manipulate with speed/link in software. The relavant MII
+ speed/duplex parameters could be effectively handled in user-specified fuction.
+ Currently tested with mpc866ads.
+
+config FIXED_MII_10_FDX
+ bool "Emulation for 10M Fdx fixed PHY behavior"
+ depends on FIXED_PHY
+
+config FIXED_MII_100_FDX
+ bool "Emulation for 100M Fdx fixed PHY behavior"
+ depends on FIXED_PHY
+
endmenu
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 7da0e3d..dfdafe9 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -46,6 +46,35 @@ static struct phy_driver genphy_driver;
extern int mdio_bus_init(void);
extern void mdio_bus_exit(void);
+struct phy_device* phy_device_create(struct mii_bus *bus, int addr, int phy_id)
+{
+ struct phy_device *dev;
+ /* We allocate the device, and initialize the
+ * default values */
+ dev = kcalloc(1, sizeof(*dev), GFP_KERNEL);
+
+ if (NULL == dev)
+ return PTR_ERR(-ENOMEM);
+
+ dev->speed = 0;
+ dev->duplex = -1;
+ dev->pause = dev->asym_pause = 0;
+ dev->link = 1;
+
+ dev->autoneg = AUTONEG_ENABLE;
+
+ dev->addr = addr;
+ dev->phy_id = phy_id;
+ dev->bus = bus;
+
+ dev->state = PHY_DOWN;
+
+ spin_lock_init(&dev->lock);
+
+ return dev;
+}
+EXPORT_SYMBOL(phy_device_create);
+
/* get_phy_device
*
* description: Reads the ID registers of the PHY at addr on the
@@ -78,28 +107,8 @@ struct phy_device * get_phy_device(struc
/* If the phy_id is all Fs, there is no device there */
if (0xffffffff == phy_id)
return NULL;
-
- /* Otherwise, we allocate the device, and initialize the
- * default values */
- dev = kcalloc(1, sizeof(*dev), GFP_KERNEL);
- if (NULL == dev)
- return ERR_PTR(-ENOMEM);
-
- dev->speed = 0;
- dev->duplex = -1;
- dev->pause = dev->asym_pause = 0;
- dev->link = 1;
-
- dev->autoneg = AUTONEG_ENABLE;
-
- dev->addr = addr;
- dev->phy_id = phy_id;
- dev->bus = bus;
-
- dev->state = PHY_DOWN;
-
- spin_lock_init(&dev->lock);
+ dev = phy_device_create(bus, addr, phy_id);
return dev;
}
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 331521a..9447a57 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -378,6 +378,7 @@ int phy_mii_ioctl(struct phy_device *phy
struct mii_ioctl_data *mii_data, int cmd);
int phy_start_interrupts(struct phy_device *phydev);
void phy_print_status(struct phy_device *phydev);
+struct phy_device* phy_device_create(struct mii_bus *bus, int addr, int phy_id);
extern struct bus_type mdio_bus_type;
#endif /* __PHY_H */
^ permalink raw reply related
* [PATCH 4/6] FS_ENET: phydev pointer may be dereferenced without NULL check
From: Vitaly Bordug @ 2006-06-23 23:17 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <20060623231648.6721.3495.stgit@localhost.localdomain>
When interface is down, phy is "disconnected" from the bus and phydev is NULL.
But ethtool may try to get/set phy regs even at that time, which results in
NULL pointer dereference and OOPS hereby.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
---
drivers/net/fs_enet/fs_enet-main.c | 4 ++++
1 files changed, 4 insertions(+), 0 deletions(-)
diff --git a/drivers/net/fs_enet/fs_enet-main.c b/drivers/net/fs_enet/fs_enet-main.c
index 302ecaa..e475e22 100644
--- a/drivers/net/fs_enet/fs_enet-main.c
+++ b/drivers/net/fs_enet/fs_enet-main.c
@@ -882,12 +882,16 @@ static void fs_get_regs(struct net_devic
static int fs_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
{
struct fs_enet_private *fep = netdev_priv(dev);
+ if (!fep->phydev)
+ return -EINVAL;
return phy_ethtool_gset(fep->phydev, cmd);
}
static int fs_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
{
struct fs_enet_private *fep = netdev_priv(dev);
+ if (!fep->phydev)
+ return -EINVAL;
phy_ethtool_sset(fep->phydev, cmd);
return 0;
}
^ permalink raw reply related
* [PATCH 0/6] Add mpc8560 support to powerpc
From: Vitaly Bordug @ 2006-06-23 19:12 UTC (permalink / raw)
To: linuxppc-dev
This is a first preliminary series to move 8560ads to powerpc and hence finish
85xx family in terms of merge. Subsequient fs_enet/PAL patches are required
for the following to work, but submitted here as reference only
(will be updated and sent to netdev shortly).
ATM not all points are adressed, there still may be bugs, but in general it works.
Most of the SoC stuff (UARTs, Gig eth, 100BaseT FCC) as well as the PCI stuff are
functional.
All the comments are greatly appreciated.
--
Sincerely, Vitaly
^ permalink raw reply
* powerpc: Adding the use of the firmware soft-reset-nmi to kdump.
From: David Wilder @ 2006-06-23 22:29 UTC (permalink / raw)
To: linuxppc-dev, paulus, Andrew Morton, fastboot, Haren Myneni
[-- Attachment #1: Type: text/plain, Size: 3222 bytes --]
This is a reposting of the patch posted on June 14.
http://ozlabs.org/pipermail/linuxppc-dev/2006-June/023705.html
I had no comments on my previous posting. It should be ready to pickup
by Andrew or Paul.
The attached patch applies clean to the torvalds/linux-2.6.git
Thanks
- Patch Description
With this patch, kdump uses the firmware soft-rest NMI for two purposes:
1) Initiate the kdump (take a crash dump) by issuing a soft-reset.
2) Break a CPU out of a deadlock condition that is detected during kdump
processing.
When a soft-reset is initiated each CPU will enter
system_reset_exception() and set its corresponding bit in the global
bit-array cpus_in_sr then call die(). When die() finds the CPU’s bit set
in cpu_in_sr crash_kexec() is called to initiate a crash dump. The first
CPU to enter crash_kexec() is called the “crashing CPU”. All other CPUs
are “secondary CPUs”. The secondary CPU’s pass through to
crash_kexec_secondary() and sleep. The crashing CPU waits for all CPUs
to enter via soft-reset then boots the kdump kernel (see
crash_soft_reset_check())
When the system crashes due to a panic or exception, crash_kexec() is
called by panic() or die(). The crashing CPU sends an IPI to all other
CPUs to notify them of the pending shutdown. If a CPU is in a deadlock
or hung state with interrupts disabled, the IPI will not be delivered.
The result being, that the kdump kernel is not booted. This problem is
solved with the use of a firmware generated soft-reset. After the
crashing_cpu has issued the IPI, it waits for 10 sec for all CPUs to
enter crash_ipi_callback(). A CPU signifies its entry to
crash_ipi_callback() by setting its corresponding bit in the
cpus_in_crash bit array. After 10 sec, if one or more CPUs have not set
their bit in cpus_in_crash we assume that the CPU(s) is deadlocked. The
operator is then prompted to generate a soft-reset to break the
deadlock. Each CPU enters the soft reset handler as described above.
Two conditions must be handled at this point:
1) The system crashed because the operator generated a soft-reset. See
#1 above.
2) The system had crashed before the soft-reset was generated ( in the
case of a Panic or oops…).
The first CPU to enter crash_kexec() uses the state of the kexec_lock to
determine this state. If kexec_lock is already held then condition 2 is
true and crash_kexec_secondary() is called, else; this CPU is flagged as
the crashing CPU, the kexec_lock is acquired and crash_kexec() proceeds
as described above.
Each additional CPUs responding to the soft-reset will pass through
crash_kexec() to kexec_secondary(). All secondary CPUs call
crash_ipi_callback() readying them self's for the shutdown. When ready
they clear their bit in cpus_in_sr. The crashing CPU waits in
kexec_secondary() until all other CPUs have cleared their bits in
cpus_in_sr. The kexec kernel boot is then started.
Signed-off-by: Haren Myneni <haren at us.ibm.com <https://ozlabs.org/mailman/listinfo/linuxppc-dev>>
Signed-off-by: David Wilder <dwilder at us.ibm.com <https://ozlabs.org/mailman/listinfo/linuxppc-dev>>
--
--
David Wilder
IBM Linux Technology Center
Beaverton, Oregon, USA
dwilder@us.ibm.com
(503)578-3789
[-- Attachment #2: ppc64-softreset-in-k-dump-2.6.17-git.patch --]
[-- Type: text/x-patch, Size: 10067 bytes --]
diff --git a/arch/powerpc/kernel/crash.c b/arch/powerpc/kernel/crash.c
index dbcb859..857629f 100644
--- a/arch/powerpc/kernel/crash.c
+++ b/arch/powerpc/kernel/crash.c
@@ -24,9 +24,11 @@
#include <linux/init.h>
#include <linux/irq.h>
#include <linux/types.h>
+#include <linux/irq.h>
#include <asm/processor.h>
#include <asm/machdep.h>
+#include <asm/kexec.h>
#include <asm/kdump.h>
#include <asm/lmb.h>
#include <asm/firmware.h>
@@ -41,6 +43,7 @@
/* This keeps a track of which one is crashing cpu. */
int crashing_cpu = -1;
+static cpumask_t cpus_in_crash = CPU_MASK_NONE;
static u32 *append_elf_note(u32 *buf, char *name, unsigned type, void *data,
size_t data_len)
@@ -98,34 +101,66 @@ static void crash_save_this_cpu(struct p
}
#ifdef CONFIG_SMP
-static atomic_t waiting_for_crash_ipi;
+static atomic_t enter_on_soft_reset = ATOMIC_INIT(0);
void crash_ipi_callback(struct pt_regs *regs)
{
int cpu = smp_processor_id();
- if (cpu == crashing_cpu)
- return;
-
if (!cpu_online(cpu))
return;
- if (ppc_md.kexec_cpu_down)
- ppc_md.kexec_cpu_down(1, 1);
-
local_irq_disable();
+ if (!cpu_isset(cpu, cpus_in_crash))
+ crash_save_this_cpu(regs, cpu);
+ cpu_set(cpu, cpus_in_crash);
- crash_save_this_cpu(regs, cpu);
- atomic_dec(&waiting_for_crash_ipi);
+ /*
+ * Entered via soft-reset - could be the kdump
+ * process is invoked using soft-reset or user activated
+ * it if some CPU did not respond to an IPI.
+ * For soft-reset, the secondary CPU can enter this func
+ * twice. 1 - using IPI, and 2. soft-reset.
+ * Tell the kexec CPU that entered via soft-reset and ready
+ * to go down.
+ */
+ if (cpu_isset(cpu, cpus_in_sr)) {
+ cpu_clear(cpu, cpus_in_sr);
+ atomic_inc(&enter_on_soft_reset);
+ }
+
+ /*
+ * Starting the kdump boot.
+ * This barrier is needed to make sure that all CPUs are stopped.
+ * If not, soft-reset will be invoked to bring other CPUs.
+ */
+ while (!cpu_isset(crashing_cpu, cpus_in_crash))
+ cpu_relax();
+
+ if (ppc_md.kexec_cpu_down)
+ ppc_md.kexec_cpu_down(1, 1);
kexec_smp_wait();
/* NOTREACHED */
}
-static void crash_kexec_prepare_cpus(void)
+/*
+ * Wait until all CPUs are entered via soft-reset.
+ */
+static void crash_soft_reset_check(int cpu)
+{
+ unsigned int ncpus = num_online_cpus() - 1;/* Excluding the panic cpu */
+
+ cpu_clear(cpu, cpus_in_sr);
+ while (atomic_read(&enter_on_soft_reset) != ncpus)
+ cpu_relax();
+}
+
+
+static void crash_kexec_prepare_cpus(int cpu)
{
unsigned int msecs;
- atomic_set(&waiting_for_crash_ipi, num_online_cpus() - 1);
+ unsigned int ncpus = num_online_cpus() - 1;/* Excluding the panic cpu */
crash_send_ipi(crash_ipi_callback);
smp_wmb();
@@ -133,14 +168,13 @@ static void crash_kexec_prepare_cpus(voi
/*
* FIXME: Until we will have the way to stop other CPUSs reliabally,
* the crash CPU will send an IPI and wait for other CPUs to
- * respond. If not, proceed the kexec boot even though we failed to
- * capture other CPU states.
+ * respond.
* Delay of at least 10 seconds.
*/
- printk(KERN_ALERT "Sending IPI to other cpus...\n");
+ printk(KERN_EMERG "Sending IPI to other cpus...\n");
msecs = 10000;
- while ((atomic_read(&waiting_for_crash_ipi) > 0) && (--msecs > 0)) {
- barrier();
+ while ((cpus_weight(cpus_in_crash) < ncpus) && (--msecs > 0)) {
+ cpu_relax();
mdelay(1);
}
@@ -149,18 +183,71 @@ static void crash_kexec_prepare_cpus(voi
/*
* FIXME: In case if we do not get all CPUs, one possibility: ask the
* user to do soft reset such that we get all.
- * IPI handler is already set by the panic cpu initially. Therefore,
- * all cpus could invoke this handler from die() and the panic CPU
- * will call machine_kexec() directly from this handler to do
- * kexec boot.
- */
- if (atomic_read(&waiting_for_crash_ipi))
- printk(KERN_ALERT "done waiting: %d cpus not responding\n",
- atomic_read(&waiting_for_crash_ipi));
+ * Soft-reset will be used until better mechanism is implemented.
+ */
+ if (cpus_weight(cpus_in_crash) < ncpus) {
+ printk(KERN_EMERG "done waiting: %d cpu(s) not responding\n",
+ ncpus - cpus_weight(cpus_in_crash));
+ printk(KERN_EMERG "Activate soft-reset to stop other cpu(s)\n");
+ cpus_in_sr = CPU_MASK_NONE;
+ atomic_set(&enter_on_soft_reset, 0);
+ while (cpus_weight(cpus_in_crash) < ncpus)
+ cpu_relax();
+ }
+ /*
+ * Make sure all CPUs are entered via soft-reset if the kdump is
+ * invoked using soft-reset.
+ */
+ if (cpu_isset(cpu, cpus_in_sr))
+ crash_soft_reset_check(cpu);
/* Leave the IPI callback set */
}
+
+/*
+ * This function will be called by secondary cpus or by kexec cpu
+ * if soft-reset is activated to stop some CPUs.
+ */
+void crash_kexec_secondary(struct pt_regs *regs)
+{
+ int cpu = smp_processor_id();
+ unsigned long flags;
+ int msecs = 5;
+
+ local_irq_save(flags);
+ /* Wait 5ms if the kexec CPU is not entered yet. */
+ while (crashing_cpu < 0) {
+ if (--msecs < 0) {
+ /*
+ * Either kdump image is not loaded or
+ * kdump process is not started - Probably xmon
+ * exited using 'x'(exit and recover) or
+ * kexec_should_crash() failed for all running tasks.
+ */
+ cpu_clear(cpu, cpus_in_sr);
+ local_irq_restore(flags);
+ return;
+ }
+ mdelay(1);
+ cpu_relax();
+ }
+ if (cpu == crashing_cpu) {
+ /*
+ * Panic CPU will enter this func only via soft-reset.
+ * Wait until all secondary CPUs entered and
+ * then start kexec boot.
+ */
+ crash_soft_reset_check(cpu);
+ cpu_set(crashing_cpu, cpus_in_crash);
+ if (ppc_md.kexec_cpu_down)
+ ppc_md.kexec_cpu_down(1, 0);
+ machine_kexec(kexec_crash_image);
+ /* NOTREACHED */
+ }
+ crash_ipi_callback(regs);
+}
+
#else
-static void crash_kexec_prepare_cpus(void)
+static void crash_kexec_prepare_cpus(int cpu)
{
/*
* move the secondarys to us so that we can copy
@@ -171,6 +258,10 @@ static void crash_kexec_prepare_cpus(voi
smp_release_cpus();
}
+void crash_kexec_secondary(struct pt_regs *regs)
+{
+ cpus_in_sr = CPU_MASK_NONE;
+}
#endif
void default_machine_crash_shutdown(struct pt_regs *regs)
@@ -199,14 +290,14 @@ void default_machine_crash_shutdown(stru
desc->handler->disable(irq);
}
- if (ppc_md.kexec_cpu_down)
- ppc_md.kexec_cpu_down(1, 0);
-
/*
* Make a note of crashing cpu. Will be used in machine_kexec
* such that another IPI will not be sent.
*/
crashing_cpu = smp_processor_id();
- crash_kexec_prepare_cpus();
crash_save_this_cpu(regs, crashing_cpu);
+ crash_kexec_prepare_cpus(crashing_cpu);
+ cpu_set(crashing_cpu, cpus_in_crash);
+ if (ppc_md.kexec_cpu_down)
+ ppc_md.kexec_cpu_down(1, 0);
}
diff --git a/arch/powerpc/kernel/traps.c b/arch/powerpc/kernel/traps.c
index 91a6e04..b94a790 100644
--- a/arch/powerpc/kernel/traps.c
+++ b/arch/powerpc/kernel/traps.c
@@ -51,9 +51,13 @@
#include <asm/firmware.h>
#include <asm/processor.h>
#endif
+#include <asm/kexec.h>
#ifdef CONFIG_PPC64 /* XXX */
#define _IO_BASE pci_io_base
+#ifdef CONFIG_KEXEC
+cpumask_t cpus_in_sr = CPU_MASK_NONE;
+#endif
#endif
#ifdef CONFIG_DEBUGGER
@@ -96,7 +100,7 @@ static DEFINE_SPINLOCK(die_lock);
int die(const char *str, struct pt_regs *regs, long err)
{
- static int die_counter, crash_dump_start = 0;
+ static int die_counter;
if (debugger(regs))
return 1;
@@ -128,22 +132,13 @@ int die(const char *str, struct pt_regs
print_modules();
show_regs(regs);
bust_spinlocks(0);
-
- if (!crash_dump_start && kexec_should_crash(current)) {
- crash_dump_start = 1;
- spin_unlock_irq(&die_lock);
- crash_kexec(regs);
- /* NOTREACHED */
- }
spin_unlock_irq(&die_lock);
- if (crash_dump_start)
- /*
- * Only for soft-reset: Other CPUs will be responded to an IPI
- * sent by first kexec CPU.
- */
- for(;;)
- ;
+ if (kexec_should_crash(current) ||
+ kexec_sr_activated(smp_processor_id()))
+ crash_kexec(regs);
+ crash_kexec_secondary(regs);
+
if (in_interrupt())
panic("Fatal exception in interrupt");
@@ -205,6 +200,10 @@ void system_reset_exception(struct pt_re
if (ppc_md.system_reset_exception(regs))
return;
}
+
+#ifdef CONFIG_KEXEC
+ cpu_set(smp_processor_id(), cpus_in_sr);
+#endif
die("System Reset", regs, SIGABRT);
diff --git a/include/asm-powerpc/kexec.h b/include/asm-powerpc/kexec.h
index efe8872..610c75e 100644
--- a/include/asm-powerpc/kexec.h
+++ b/include/asm-powerpc/kexec.h
@@ -115,6 +115,11 @@ extern void kexec_smp_wait(void); /* get
extern void __init kexec_setup(void);
extern int crashing_cpu;
extern void crash_send_ipi(void (*crash_ipi_callback)(struct pt_regs *));
+extern cpumask_t cpus_in_sr;
+static inline int kexec_sr_activated(int cpu)
+{
+ return cpu_isset(cpu,cpus_in_sr);
+}
#endif /* __powerpc64 __ */
struct kimage;
@@ -124,10 +129,13 @@ extern int default_machine_kexec_prepare
extern void default_machine_crash_shutdown(struct pt_regs *regs);
extern void machine_kexec_simple(struct kimage *image);
+extern void crash_kexec_secondary(struct pt_regs *regs);
extern int overlaps_crashkernel(unsigned long start, unsigned long size);
extern void reserve_crashkernel(void);
#else /* !CONFIG_KEXEC */
+static inline int kexec_sr_activated(int cpu) { return 0; }
+static inline void crash_kexec_secondary(struct pt_regs *regs) { }
static inline int overlaps_crashkernel(unsigned long start, unsigned long size)
{
diff --git a/kernel/kexec.c b/kernel/kexec.c
index 58f0f38..50087ec 100644
--- a/kernel/kexec.c
+++ b/kernel/kexec.c
@@ -1042,7 +1042,6 @@ asmlinkage long compat_sys_kexec_load(un
void crash_kexec(struct pt_regs *regs)
{
- struct kimage *image;
int locked;
@@ -1056,12 +1055,11 @@ void crash_kexec(struct pt_regs *regs)
*/
locked = xchg(&kexec_lock, 1);
if (!locked) {
- image = xchg(&kexec_crash_image, NULL);
- if (image) {
+ if (kexec_crash_image) {
struct pt_regs fixed_regs;
crash_setup_regs(&fixed_regs, regs);
machine_crash_shutdown(&fixed_regs);
- machine_kexec(image);
+ machine_kexec(kexec_crash_image);
}
xchg(&kexec_lock, 0);
}
^ permalink raw reply related
* Re: "merge" branch reset in powerpc.git tree
From: Josh Boyer @ 2006-06-23 19:28 UTC (permalink / raw)
To: Arnd Bergmann; +Cc: linuxppc-dev, Paul Mackerras
In-Reply-To: <200606232124.52879.arnd.bergmann@de.ibm.com>
On Fri, 2006-06-23 at 21:24 +0200, Arnd Bergmann wrote:
> On Friday 23 June 2006 21:10, Josh Boyer wrote:
> > git reset --hard 5fa21d821f6972e70942f2c555ec29dde962bdb2
> >
> > That will reset the branch to the commit ID. NOTE: If you have local
> > changes on top, they will be wiped out.
> >
> > There might be a way to do it without losing local changes, but I'm a
> > git idiot myself still.
> >
> My understanding is that you are not supposed to have local changes
> on the branch you are pulling into, but have another branch for
> merging the remote tree with your own changes.
True. But there is nothing to prevent people from doing it. So I was
just warning them :).
josh
^ permalink raw reply
* Re: "merge" branch reset in powerpc.git tree
From: Arnd Bergmann @ 2006-06-23 19:24 UTC (permalink / raw)
To: linuxppc-dev; +Cc: Paul Mackerras
In-Reply-To: <1151089824.22158.2.camel@weaponx.rchland.ibm.com>
On Friday 23 June 2006 21:10, Josh Boyer wrote:
> git reset --hard 5fa21d821f6972e70942f2c555ec29dde962bdb2
>=20
> That will reset the branch to the commit ID. =A0NOTE: =A0If you have local
> changes on top, they will be wiped out.
>=20
> There might be a way to do it without losing local changes, but I'm a
> git idiot myself still.
>=20
My understanding is that you are not supposed to have local changes
on the branch you are pulling into, but have another branch for
merging the remote tree with your own changes.
Then again, I'm pretty clueless about git as well.
Arnd <><
^ permalink raw reply
* [RFC] implement error event delivery to user space
From: Arnd Bergmann @ 2006-06-23 19:12 UTC (permalink / raw)
To: cbe-oss-dev; +Cc: linuxppc-dev
From: Christoph Hellwig <hch@infradead.org>
This tries to fix spufs so we have an interface closer
to what is specified in the man page for events
returned in the third argument of spu_run.
Fortunately, libspe has never been using the returned
contents of that register, as they were the same
as the return code of spu_run (duh!).
This returns what we need from libspe, but only
when a flag was set on spu_create. Now that flag
was previously not documented, so we're actually
extending the semantics here.
One big question that keeps nagging me is whether
we want to actually allow a thread to run on after
it has hit a critical error like invalid DMA addresses
or illegal opcodes. I can't really think of an example
where we would want to do that, so I tend to go down
the easy route of not supporting that, but there may
be scenarios that I haven't thought of.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Index: linus-2.6/arch/powerpc/platforms/cell/spu_base.c
===================================================================
--- linus-2.6.orig/arch/powerpc/platforms/cell/spu_base.c
+++ linus-2.6/arch/powerpc/platforms/cell/spu_base.c
@@ -46,21 +46,21 @@ EXPORT_SYMBOL_GPL(spu_priv1_ops);
static int __spu_trap_invalid_dma(struct spu *spu)
{
pr_debug("%s\n", __FUNCTION__);
- force_sig(SIGBUS, /* info, */ current);
+ spu->dma_callback(spu, SPE_EVENT_INVALID_DMA);
return 0;
}
static int __spu_trap_dma_align(struct spu *spu)
{
pr_debug("%s\n", __FUNCTION__);
- force_sig(SIGBUS, /* info, */ current);
+ spu->dma_callback(spu, SPE_EVENT_DMA_ALIGNMENT);
return 0;
}
static int __spu_trap_error(struct spu *spu)
{
pr_debug("%s\n", __FUNCTION__);
- force_sig(SIGILL, /* info, */ current);
+ spu->dma_callback(spu, SPE_EVENT_SPE_ERROR);
return 0;
}
Index: linus-2.6/arch/powerpc/platforms/cell/spufs/inode.c
===================================================================
--- linus-2.6.orig/arch/powerpc/platforms/cell/spufs/inode.c
+++ linus-2.6/arch/powerpc/platforms/cell/spufs/inode.c
@@ -225,7 +225,8 @@ struct file_operations spufs_context_fop
};
static int
-spufs_mkdir(struct inode *dir, struct dentry *dentry, int mode)
+spufs_mkdir(struct inode *dir, struct dentry *dentry, unsigned int flags,
+ int mode)
{
int ret;
struct inode *inode;
@@ -245,6 +246,8 @@ spufs_mkdir(struct inode *dir, struct de
if (!ctx)
goto out_iput;
+ ctx->flags = flags;
+
inode->i_op = &spufs_dir_inode_operations;
inode->i_fop = &simple_dir_operations;
ret = spufs_fill_dir(dentry, spufs_dir_contents, mode, ctx);
@@ -305,7 +308,7 @@ long spufs_create_thread(struct nameidat
goto out;
/* all flags are reserved */
- if (flags)
+ if (flags & (~SPU_CREATE_FLAG_ALL))
goto out;
dentry = lookup_create(nd, 1);
@@ -318,7 +321,7 @@ long spufs_create_thread(struct nameidat
goto out_dput;
mode &= ~current->fs->umask;
- ret = spufs_mkdir(nd->dentry->d_inode, dentry, mode & S_IRWXUGO);
+ ret = spufs_mkdir(nd->dentry->d_inode, dentry, flags, mode & S_IRWXUGO);
if (ret)
goto out_dput;
Index: linus-2.6/arch/powerpc/platforms/cell/spufs/run.c
===================================================================
--- linus-2.6.orig/arch/powerpc/platforms/cell/spufs/run.c
+++ linus-2.6/arch/powerpc/platforms/cell/spufs/run.c
@@ -14,6 +14,26 @@ void spufs_stop_callback(struct spu *spu
wake_up_all(&ctx->stop_wq);
}
+void spufs_dma_callback(struct spu *spu, int type)
+{
+ struct spu_context *ctx = spu->ctx;
+
+ if (ctx->flags & SPU_CREATE_EVENTS_ENABLED) {
+ ctx->event_return |= type;
+ wake_up_all(&ctx->stop_wq);
+ } else {
+ switch (type) {
+ case SPE_EVENT_DMA_ALIGNMENT:
+ case SPE_EVENT_INVALID_DMA:
+ force_sig(SIGBUS, /* info, */ current);
+ break;
+ case SPE_EVENT_SPE_ERROR:
+ force_sig(SIGILL, /* info */ current);
+ break;
+ }
+ }
+}
+
static inline int spu_stopped(struct spu_context *ctx, u32 * stat)
{
struct spu *spu;
@@ -28,8 +48,7 @@ static inline int spu_stopped(struct spu
return (!(*stat & 0x1) || pte_fault || spu->class_0_pending) ? 1 : 0;
}
-static inline int spu_run_init(struct spu_context *ctx, u32 * npc,
- u32 * status)
+static inline int spu_run_init(struct spu_context *ctx, u32 * npc)
{
int ret;
@@ -72,7 +91,7 @@ static inline int spu_reacquire_runnable
SPU_STATUS_STOPPED_BY_HALT)) {
return *status;
}
- if ((ret = spu_run_init(ctx, npc, status)) != 0)
+ if ((ret = spu_run_init(ctx, npc)) != 0)
return ret;
return 0;
}
@@ -177,46 +196,49 @@ static inline int spu_process_events(str
}
long spufs_run_spu(struct file *file, struct spu_context *ctx,
- u32 * npc, u32 * status)
+ u32 *npc, u32 *event)
{
int ret;
+ u32 status;
if (down_interruptible(&ctx->run_sema))
return -ERESTARTSYS;
- ret = spu_run_init(ctx, npc, status);
+ ctx->event_return = 0;
+ ret = spu_run_init(ctx, npc);
if (ret)
goto out;
do {
- ret = spufs_wait(ctx->stop_wq, spu_stopped(ctx, status));
+ ret = spufs_wait(ctx->stop_wq, spu_stopped(ctx, &status));
if (unlikely(ret))
break;
- if ((*status & SPU_STATUS_STOPPED_BY_STOP) &&
- (*status >> SPU_STOP_STATUS_SHIFT == 0x2104)) {
+ if ((status & SPU_STATUS_STOPPED_BY_STOP) &&
+ (status >> SPU_STOP_STATUS_SHIFT == 0x2104)) {
ret = spu_process_callback(ctx);
if (ret)
break;
- *status &= ~SPU_STATUS_STOPPED_BY_STOP;
+ status &= ~SPU_STATUS_STOPPED_BY_STOP;
}
if (unlikely(ctx->state != SPU_STATE_RUNNABLE)) {
- ret = spu_reacquire_runnable(ctx, npc, status);
+ ret = spu_reacquire_runnable(ctx, npc, &status);
if (ret)
goto out;
continue;
}
ret = spu_process_events(ctx);
- } while (!ret && !(*status & (SPU_STATUS_STOPPED_BY_STOP |
+ } while (!ret && !(status & (SPU_STATUS_STOPPED_BY_STOP |
SPU_STATUS_STOPPED_BY_HALT)));
ctx->ops->runcntl_stop(ctx);
- ret = spu_run_fini(ctx, npc, status);
+ ret = spu_run_fini(ctx, npc, &status);
if (!ret)
- ret = *status;
+ ret = status;
spu_yield(ctx);
out:
+ *event = ctx->event_return;
up(&ctx->run_sema);
return ret;
}
Index: linus-2.6/arch/powerpc/platforms/cell/spufs/sched.c
===================================================================
--- linus-2.6.orig/arch/powerpc/platforms/cell/spufs/sched.c
+++ linus-2.6/arch/powerpc/platforms/cell/spufs/sched.c
@@ -102,7 +102,6 @@ static inline void bind_context(struct s
spu->number, spu->node);
spu->ctx = ctx;
spu->flags = 0;
- ctx->flags = 0;
ctx->spu = spu;
ctx->ops = &spu_hw_ops;
spu->pid = current->pid;
@@ -113,6 +112,7 @@ static inline void bind_context(struct s
spu->wbox_callback = spufs_wbox_callback;
spu->stop_callback = spufs_stop_callback;
spu->mfc_callback = spufs_mfc_callback;
+ spu->dma_callback = spufs_dma_callback;
mb();
spu_unmap_mappings(ctx);
spu_restore(&ctx->csa, spu);
@@ -134,12 +134,12 @@ static inline void unbind_context(struct
spu->wbox_callback = NULL;
spu->stop_callback = NULL;
spu->mfc_callback = NULL;
+ spu->dma_callback = NULL;
spu->mm = NULL;
spu->pid = 0;
spu->prio = MAX_PRIO;
ctx->ops = &spu_backing_ops;
ctx->spu = NULL;
- ctx->flags = 0;
spu->flags = 0;
spu->ctx = NULL;
}
Index: linus-2.6/arch/powerpc/platforms/cell/spufs/spufs.h
===================================================================
--- linus-2.6.orig/arch/powerpc/platforms/cell/spufs/spufs.h
+++ linus-2.6/arch/powerpc/platforms/cell/spufs/spufs.h
@@ -67,7 +67,8 @@ struct spu_context {
u32 tagwait;
struct spu_context_ops *ops;
struct work_struct reap_work;
- u64 flags;
+ unsigned long flags;
+ unsigned long event_return;
};
struct mfc_dma_command {
@@ -184,5 +185,6 @@ void spufs_ibox_callback(struct spu *spu
void spufs_wbox_callback(struct spu *spu);
void spufs_stop_callback(struct spu *spu);
void spufs_mfc_callback(struct spu *spu);
+void spufs_dma_callback(struct spu *spu, int type);
#endif
Index: linus-2.6/include/asm-powerpc/spu.h
===================================================================
--- linus-2.6.orig/include/asm-powerpc/spu.h
+++ linus-2.6/include/asm-powerpc/spu.h
@@ -138,6 +138,7 @@ struct spu {
void (* ibox_callback)(struct spu *spu);
void (* stop_callback)(struct spu *spu);
void (* mfc_callback)(struct spu *spu);
+ void (* dma_callback)(struct spu *spu, int type);
char irq_c0[8];
char irq_c1[8];
@@ -169,6 +170,19 @@ extern struct spufs_calls {
struct module *owner;
} spufs_calls;
+/* return status from spu_run, same as in libspe */
+#define SPE_EVENT_DMA_ALIGNMENT 0x0008 /*A DMA alignment error */
+#define SPE_EVENT_SPE_ERROR 0x0010 /*An illegal instruction error*/
+#define SPE_EVENT_SPE_DATA_SEGMENT 0x0020 /*A DMA segmentation error */
+#define SPE_EVENT_SPE_DATA_STORAGE 0x0040 /*A DMA storage error */
+#define SPE_EVENT_INVALID_DMA 0x0800 /* Invalid MFC DMA */
+
+/*
+ * Flags for sys_spu_create.
+ */
+#define SPU_CREATE_EVENTS_ENABLED 0x0001
+#define SPU_CREATE_FLAG_ALL 0x0001 /* mask of all valid flags */
+
#ifdef CONFIG_SPU_FS_MODULE
int register_spu_syscalls(struct spufs_calls *calls);
void unregister_spu_syscalls(struct spufs_calls *calls);
Index: linus-2.6/arch/powerpc/platforms/cell/spufs/syscalls.c
===================================================================
--- linus-2.6.orig/arch/powerpc/platforms/cell/spufs/syscalls.c
+++ linus-2.6/arch/powerpc/platforms/cell/spufs/syscalls.c
@@ -38,7 +38,7 @@ static long do_spu_run(struct file *filp
u32 npc, status;
ret = -EFAULT;
- if (get_user(npc, unpc) || get_user(status, ustatus))
+ if (get_user(npc, unpc))
goto out;
/* check if this file was created by spu_create */
@@ -49,7 +49,10 @@ static long do_spu_run(struct file *filp
i = SPUFS_I(filp->f_dentry->d_inode);
ret = spufs_run_spu(filp, i->i_ctx, &npc, &status);
- if (put_user(npc, unpc) || put_user(status, ustatus))
+ if (put_user(npc, unpc))
+ ret = -EFAULT;
+
+ if (ustatus && put_user(status, ustatus))
ret = -EFAULT;
out:
return ret;
^ permalink raw reply
* Re: "merge" branch reset in powerpc.git tree
From: Josh Boyer @ 2006-06-23 19:10 UTC (permalink / raw)
To: Dave C Boutcher; +Cc: linuxppc-dev, Paul Mackerras
In-Reply-To: <17564.6980.694265.974713@hound.rchland.ibm.com>
On Fri, 2006-06-23 at 11:48 -0500, Dave C Boutcher wrote:
> On Fri, 23 Jun 2006 21:44:58 +1000, Paul Mackerras <paulus@samba.org> said:
> >
> > If you are following the powerpc.git tree, and you pull the "merge"
> > branch, you will need to reset it to have commit ID
> > 5fa21d821f6972e70942f2c555ec29dde962bdb2 as its head. That's also the
> > head of the "master" branch and of Linus' linux-2.6 tree at the
> > moment.
>
> At risk of appearing like a git ignoramous...could you post the
> command to perform such a reset?
Run the following in that branch:
git reset --hard 5fa21d821f6972e70942f2c555ec29dde962bdb2
That will reset the branch to the commit ID. NOTE: If you have local
changes on top, they will be wiped out.
There might be a way to do it without losing local changes, but I'm a
git idiot myself still.
josh
^ permalink raw reply
* [PATCH 0/5] trivial spufs fixes
From: arnd @ 2006-06-23 19:03 UTC (permalink / raw)
To: paulus; +Cc: linuxppc-dev, cbe-oss-dev, linux-kernel
These bug fixes have come up since the previous submission.
Please merge for 2.6.18.
Arnd <><
^ permalink raw reply
* [PATCH 5/5] spufs: fix spufs_mfc_flush prototype
From: arnd @ 2006-06-23 18:57 UTC (permalink / raw)
To: paulus; +Cc: Arnd Bergmann, linuxppc-dev, cbe-oss-dev, linux-kernel
In-Reply-To: <20060623185746.037897000@klappe.arndb.de>
The prototype for the flush file operation now has another
argument in 2.6.18.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Index: linus-2.6/arch/powerpc/platforms/cell/spufs/file.c
===================================================================
--- linus-2.6.orig/arch/powerpc/platforms/cell/spufs/file.c
+++ linus-2.6/arch/powerpc/platforms/cell/spufs/file.c
@@ -1150,7 +1150,7 @@ static unsigned int spufs_mfc_poll(struc
return mask;
}
-static int spufs_mfc_flush(struct file *file)
+static int spufs_mfc_flush(struct file *file, fl_owner_t id)
{
struct spu_context *ctx = file->private_data;
int ret;
@@ -1176,7 +1176,7 @@ out:
static int spufs_mfc_fsync(struct file *file, struct dentry *dentry,
int datasync)
{
- return spufs_mfc_flush(file);
+ return spufs_mfc_flush(file, 0);
}
static int spufs_mfc_fasync(int fd, struct file *file, int on)
--
^ permalink raw reply
* [PATCH 4/5] spufs: fix class0 interrupt assignment
From: arnd @ 2006-06-23 18:57 UTC (permalink / raw)
To: paulus; +Cc: Arnd Bergmann, linuxppc-dev, cbe-oss-dev, linux-kernel
In-Reply-To: <20060623185746.037897000@klappe.arndb.de>
The class zero interrupt handling for spus
was confusing alignment and error interrupts,
so swap them.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Index: linus-2.6/arch/powerpc/platforms/cell/spu_base.c
===================================================================
--- linus-2.6.orig/arch/powerpc/platforms/cell/spu_base.c
+++ linus-2.6/arch/powerpc/platforms/cell/spu_base.c
@@ -168,12 +168,12 @@ spu_irq_class_0_bottom(struct spu *spu)
stat &= mask;
- if (stat & 1) /* invalid MFC DMA */
- __spu_trap_invalid_dma(spu);
-
- if (stat & 2) /* invalid DMA alignment */
+ if (stat & 1) /* invalid DMA alignment */
__spu_trap_dma_align(spu);
+ if (stat & 2) /* invalid MFC DMA */
+ __spu_trap_invalid_dma(spu);
+
if (stat & 4) /* error on SPU */
__spu_trap_error(spu);
--
^ permalink raw reply
* [PATCH 3/5] spufs: fix memory hotplug dependency
From: arnd @ 2006-06-23 18:57 UTC (permalink / raw)
To: paulus; +Cc: Arnd Bergmann, linuxppc-dev, cbe-oss-dev, linux-kernel
In-Reply-To: <20060623185746.037897000@klappe.arndb.de>
From: Geoff Levand <geoffrey.levand@am.sony.com>
spufs_base.c calls __add_pages, which depends on CONFIG_MEMORY_HOTPLUG.
Moved the selection of CONFIG_MEMORY_HOTPLUG from CONFIG_SPUFS_MMAP
to CONFIG_SPU_FS.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Index: linus-2.6/arch/powerpc/platforms/cell/Kconfig
===================================================================
--- linus-2.6.orig/arch/powerpc/platforms/cell/Kconfig
+++ linus-2.6/arch/powerpc/platforms/cell/Kconfig
@@ -6,6 +6,7 @@ config SPU_FS
default m
depends on PPC_CELL
select SPU_BASE
+ select MEMORY_HOTPLUG
help
The SPU file system is used to access Synergistic Processing
Units on machines implementing the Broadband Processor
@@ -18,7 +19,6 @@ config SPU_BASE
config SPUFS_MMAP
bool
depends on SPU_FS && SPARSEMEM
- select MEMORY_HOTPLUG
default y
config CBE_RAS
--
^ permalink raw reply
* [PATCH 2/5] spufs: fix MFC command queue purge
From: arnd @ 2006-06-23 18:57 UTC (permalink / raw)
To: paulus; +Cc: Arnd Bergmann, linuxppc-dev, cbe-oss-dev, linux-kernel
In-Reply-To: <20060623185746.037897000@klappe.arndb.de>
From: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In the context save/restore code, the SPU MFC command queue purge
code has a bug:
static inline void wait_purge_complete(struct spu_state *csa, struct
spu *spu)
{
struct spu_priv2 __iomem *priv2 = spu->priv2;
/* Save, Step 28:
* Poll MFC_CNTL[Ps] until value '11' is
* read
* (purge complete).
*/
POLL_WHILE_FALSE(in_be64(&priv2->mfc_control_RW)
& MFC_CNTL_PURGE_DMA_COMPLETE);
}
This will exit as soon as _one_ of the 2 bits that compose
MFC_CNTL_PURGE_DMA_COMPLETE is set, and one of them happens to be
"purge in progress"... which means that we'll happily continue
restoring the MFC while it's being purged at the same time.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Index: linus-2.6/arch/powerpc/platforms/cell/spufs/switch.c
===================================================================
--- linus-2.6.orig/arch/powerpc/platforms/cell/spufs/switch.c
+++ linus-2.6/arch/powerpc/platforms/cell/spufs/switch.c
@@ -464,7 +464,8 @@ static inline void wait_purge_complete(s
* Poll MFC_CNTL[Ps] until value '11' is read
* (purge complete).
*/
- POLL_WHILE_FALSE(in_be64(&priv2->mfc_control_RW) &
+ POLL_WHILE_FALSE((in_be64(&priv2->mfc_control_RW) &
+ MFC_CNTL_PURGE_DMA_STATUS_MASK) ==
MFC_CNTL_PURGE_DMA_COMPLETE);
}
@@ -1028,7 +1029,8 @@ static inline void wait_suspend_mfc_comp
* Restore, Step 47.
* Poll MFC_CNTL[Ss] until 11 is returned.
*/
- POLL_WHILE_FALSE(in_be64(&priv2->mfc_control_RW) &
+ POLL_WHILE_FALSE((in_be64(&priv2->mfc_control_RW) &
+ MFC_CNTL_SUSPEND_DMA_STATUS_MASK) ==
MFC_CNTL_SUSPEND_COMPLETE);
}
--
^ permalink raw reply
* [PATCH 1/5] spufs: map mmio space as guarded into user space
From: arnd @ 2006-06-23 18:57 UTC (permalink / raw)
To: paulus; +Cc: linuxppc-dev, cbe-oss-dev, linux-kernel
In-Reply-To: <20060623185746.037897000@klappe.arndb.de>
From: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This fixes a bug where we don't properly map SPE MMIO space as guarded,
causing various test cases to fail, probably due to write combining and other
niceties caused by the lack of the G bit.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Index: linus-2.6/arch/powerpc/platforms/cell/spufs/file.c
===================================================================
--- linus-2.6.orig/arch/powerpc/platforms/cell/spufs/file.c
+++ linus-2.6/arch/powerpc/platforms/cell/spufs/file.c
@@ -204,7 +204,7 @@ static int spufs_cntl_mmap(struct file *
vma->vm_flags |= VM_RESERVED;
vma->vm_page_prot = __pgprot(pgprot_val(vma->vm_page_prot)
- | _PAGE_NO_CACHE);
+ | _PAGE_NO_CACHE | _PAGE_GUARDED);
vma->vm_ops = &spufs_cntl_mmap_vmops;
return 0;
@@ -675,7 +675,7 @@ static int spufs_signal1_mmap(struct fil
vma->vm_flags |= VM_RESERVED;
vma->vm_page_prot = __pgprot(pgprot_val(vma->vm_page_prot)
- | _PAGE_NO_CACHE);
+ | _PAGE_NO_CACHE | _PAGE_GUARDED);
vma->vm_ops = &spufs_signal1_mmap_vmops;
return 0;
@@ -762,7 +762,7 @@ static int spufs_signal2_mmap(struct fil
/* FIXME: */
vma->vm_flags |= VM_RESERVED;
vma->vm_page_prot = __pgprot(pgprot_val(vma->vm_page_prot)
- | _PAGE_NO_CACHE);
+ | _PAGE_NO_CACHE | _PAGE_GUARDED);
vma->vm_ops = &spufs_signal2_mmap_vmops;
return 0;
@@ -850,7 +850,7 @@ static int spufs_mss_mmap(struct file *f
vma->vm_flags |= VM_RESERVED;
vma->vm_page_prot = __pgprot(pgprot_val(vma->vm_page_prot)
- | _PAGE_NO_CACHE);
+ | _PAGE_NO_CACHE | _PAGE_GUARDED);
vma->vm_ops = &spufs_mss_mmap_vmops;
return 0;
@@ -899,7 +899,7 @@ static int spufs_mfc_mmap(struct file *f
vma->vm_flags |= VM_RESERVED;
vma->vm_page_prot = __pgprot(pgprot_val(vma->vm_page_prot)
- | _PAGE_NO_CACHE);
+ | _PAGE_NO_CACHE | _PAGE_GUARDED);
vma->vm_ops = &spufs_mfc_mmap_vmops;
return 0;
--
^ permalink raw reply
* Re: 8641 open nits
From: Kumar Gala @ 2006-06-23 18:12 UTC (permalink / raw)
To: Jon Loeliger; +Cc: linuxppc-dev@ozlabs.org list
In-Reply-To: <E1Ftncn-0008Kb-PT@jdl.com>
On Jun 23, 2006, at 10:31 AM, Jon Loeliger wrote:
> So, like, the other day Kumar Gala mumbled:
>> Jon,
>>
>> Any update on the following nits:
>> * duplication of entry in cputable
>
> Earlier, we discussed it internally, and there are a few
> issues differentiating the cores, so the sentiment was to
> leave it as is for now.
Can this be explained, I dont like the idea of having an entry to
matches on specific version and does have any differences with the
generic match. Why not remove it now and when you have something
that is special for 864x that we add it then.
>> * include of <platforms/86xx/mpc8641_hpcn.h> in asm-powerpc/mpc86xx.h
>
> That has to stay unless the IRQ patch is applied first.
> Ben said "No" to that one so far. The include stays for now.
I dont follow, what IRQ information is in mpc8641_hpcn.h that is
needed by mpc86xx.h?
>> * mpc86xx_exclude_device cleanup and movement to pci.c
>> * fixing up mpc86xx_hpcn_probe()
>
> Those are all going to be cleaned up pending Ben's IRQ rewrite.
What does probe have to do with Ben's IRQ rewrite?
- kumar
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox