* [PATCH v2 08/12] [POWERPC] CM5200 DTS
From: Marian Balakowicz @ 2007-11-03 23:52 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <20071103235210.31906.83423.stgit@hekate.izotz.org>
Add device tree source file for CM5200 board.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
---
arch/powerpc/boot/dts/cm5200.dts | 252 ++++++++++++++++++++++++++++++++++++++
1 files changed, 252 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/boot/dts/cm5200.dts
diff --git a/arch/powerpc/boot/dts/cm5200.dts b/arch/powerpc/boot/dts/cm5200.dts
new file mode 100644
index 0000000..8b3f93c
--- /dev/null
+++ b/arch/powerpc/boot/dts/cm5200.dts
@@ -0,0 +1,252 @@
+/*
+ * CM5200 board Device Tree Source
+ *
+ * Copyright (C) 2007 Semihalf
+ * Marian Balakowicz <m8@semihalf.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/*
+ * WARNING: Do not depend on this tree layout remaining static just yet.
+ * The MPC5200 device tree conventions are still in flux
+ * Keep an eye on the linuxppc-dev mailing list for more details
+ */
+
+/ {
+ model = "schindler,cm5200";
+ compatible = "schindler,cm5200","mpc5200-simple-platform";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,5200@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <20>;
+ i-cache-line-size = <20>;
+ d-cache-size = <4000>; // L1, 16K
+ i-cache-size = <4000>; // L1, 16K
+ timebase-frequency = <0>; // from bootloader
+ bus-frequency = <0>; // from bootloader
+ clock-frequency = <0>; // from bootloader
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <00000000 04000000>; // 64MB
+ };
+
+ soc5200@f0000000 {
+ model = "fsl,mpc5200b";
+ compatible = "mpc5200";
+ revision = ""; // from bootloader
+ device_type = "soc";
+ ranges = <0 f0000000 0000c000>;
+ reg = <f0000000 00000100>;
+ bus-frequency = <0>; // from bootloader
+ system-frequency = <0>; // from bootloader
+
+ cdm@200 {
+ compatible = "mpc5200b-cdm","mpc5200-cdm";
+ reg = <200 38>;
+ };
+
+ mpc5200_pic: pic@500 {
+ // 5200 interrupts are encoded into two levels;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ device_type = "interrupt-controller";
+ compatible = "mpc5200b-pic","mpc5200-pic";
+ reg = <500 80>;
+ };
+
+ gpt@600 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ cell-index = <0>;
+ reg = <600 10>;
+ interrupts = <1 9 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ fsl,has-wdt;
+ };
+
+ gpt@610 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ cell-index = <1>;
+ reg = <610 10>;
+ interrupts = <1 a 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ gpt@620 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ cell-index = <2>;
+ reg = <620 10>;
+ interrupts = <1 b 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ gpt@630 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ cell-index = <3>;
+ reg = <630 10>;
+ interrupts = <1 c 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ gpt@640 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ cell-index = <4>;
+ reg = <640 10>;
+ interrupts = <1 d 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ gpt@650 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ cell-index = <5>;
+ reg = <650 10>;
+ interrupts = <1 e 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ gpt@660 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ cell-index = <6>;
+ reg = <660 10>;
+ interrupts = <1 f 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ gpt@670 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ cell-index = <7>;
+ reg = <670 10>;
+ interrupts = <1 10 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ rtc@800 { // Real time clock
+ compatible = "mpc5200b-rtc","mpc5200-rtc";
+ device_type = "rtc";
+ reg = <800 100>;
+ interrupts = <1 5 0 1 6 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ gpio@b00 {
+ compatible = "mpc5200b-gpio","mpc5200-gpio";
+ reg = <b00 40>;
+ interrupts = <1 7 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ gpio-wkup@c00 {
+ compatible = "mpc5200b-gpio-wkup","mpc5200-gpio-wkup";
+ reg = <c00 40>;
+ interrupts = <1 8 0 0 3 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ spi@f00 {
+ device_type = "spi";
+ compatible = "mpc5200b-spi","mpc5200-spi";
+ reg = <f00 20>;
+ interrupts = <2 d 0 2 e 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ usb@1000 {
+ device_type = "usb-ohci-be";
+ compatible = "mpc5200b-ohci","mpc5200-ohci","ohci-be";
+ reg = <1000 ff>;
+ interrupts = <2 6 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ dma-controller@1200 {
+ compatible = "mpc5200b-bestcomm","mpc5200-bestcomm";
+ reg = <1200 80>;
+ interrupts = <3 0 0 3 1 0 3 2 0 3 3 0
+ 3 4 0 3 5 0 3 6 0 3 7 0
+ 3 8 0 3 9 0 3 a 0 3 b 0
+ 3 c 0 3 d 0 3 e 0 3 f 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ xlb@1f00 {
+ compatible = "mpc5200b-xlb","mpc5200-xlb";
+ reg = <1f00 100>;
+ };
+
+ serial@2000 { // PSC1
+ device_type = "serial";
+ compatible = "mpc5200b-psc-uart","mpc5200-psc-uart";
+ port-number = <0>; // Logical port assignment
+ cell-index = <0>;
+ reg = <2000 100>;
+ interrupts = <2 1 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ serial@2200 { // PSC2
+ device_type = "serial";
+ compatible = "mpc5200-psc-uart";
+ port-number = <1>; // Logical port assignment
+ cell-index = <1>;
+ reg = <2200 100>;
+ interrupts = <2 2 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ serial@2400 { // PSC3
+ device_type = "serial";
+ compatible = "mpc5200-psc-uart";
+ port-number = <2>; // Logical port assignment
+ cell-index = <2>;
+ reg = <2400 100>;
+ interrupts = <2 3 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ serial@2c00 { // PSC6
+ device_type = "serial";
+ compatible = "mpc5200b-psc-uart","mpc5200-psc-uart";
+ port-number = <5>; // Logical port assignment
+ cell-index = <5>;
+ reg = <2c00 100>;
+ interrupts = <2 4 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ ethernet@3000 {
+ device_type = "network";
+ compatible = "mpc5200b-fec","mpc5200-fec";
+ reg = <3000 800>;
+ local-mac-address = [ 00 00 00 00 00 00 ]; /* Filled in by U-Boot */
+ interrupts = <2 5 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ i2c@3d40 {
+ device_type = "i2c";
+ compatible = "mpc5200b-i2c","mpc5200-i2c","fsl-i2c";
+ reg = <3d40 40>;
+ interrupts = <2 10 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ fsl5200-clocking;
+ };
+
+ sram@8000 {
+ compatible = "mpc5200b-sram","mpc5200-sram","sram";
+ reg = <8000 4000>;
+ };
+ };
+};
^ permalink raw reply related
* [PATCH v2 09/12] [POWERPC] CM5200 defconfig
From: Marian Balakowicz @ 2007-11-03 23:53 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <20071103235210.31906.83423.stgit@hekate.izotz.org>
Add CM5200 board defconfig file.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
---
arch/powerpc/configs/cm5200_defconfig | 1031 +++++++++++++++++++++++++++++++++
1 files changed, 1031 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/configs/cm5200_defconfig
diff --git a/arch/powerpc/configs/cm5200_defconfig b/arch/powerpc/configs/cm5200_defconfig
new file mode 100644
index 0000000..a17d966
--- /dev/null
+++ b/arch/powerpc/configs/cm5200_defconfig
@@ -0,0 +1,1031 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.23
+# Mon Oct 29 14:06:34 2007
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+CONFIG_6xx=y
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_PPC_FPU=y
+# CONFIG_ALTIVEC is not set
+CONFIG_PPC_STD_MMU=y
+CONFIG_PPC_STD_MMU_32=y
+# CONFIG_PPC_MM_SLICES is not set
+# CONFIG_SMP is not set
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+# CONFIG_PPC_UDBG_16550 is not set
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+# CONFIG_SYSCTL_SYSCALL is not set
+# CONFIG_KALLSYMS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+# CONFIG_EPOLL is not set
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+# CONFIG_KMOD is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# Platform support
+#
+CONFIG_PPC_MULTIPLATFORM=y
+# CONFIG_PPC_82xx is not set
+# CONFIG_PPC_83xx is not set
+# CONFIG_PPC_86xx is not set
+CONFIG_CLASSIC32=y
+# CONFIG_PPC_CHRP is not set
+CONFIG_PPC_MPC52xx=y
+CONFIG_PPC_MPC5200=y
+# CONFIG_PPC_MPC5200_BUGFIX is not set
+CONFIG_PPC_MPC5200_SIMPLE=y
+# CONFIG_PPC_EFIKA is not set
+# CONFIG_PPC_LITE5200 is not set
+# CONFIG_PPC_PMAC is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+# CONFIG_EMBEDDED6xx is not set
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_TAU is not set
+# CONFIG_CPM2 is not set
+# CONFIG_FSL_ULI1575 is not set
+# CONFIG_PPC_BESTCOMM is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+# CONFIG_KEXEC is not set
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+CONFIG_PROC_DEVICETREE=y
+# CONFIG_CMDLINE_BOOL is not set
+CONFIG_PM=y
+# CONFIG_PM_LEGACY is not set
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_SUSPEND=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
+# CONFIG_HIBERNATION is not set
+CONFIG_SECCOMP=y
+# CONFIG_WANT_DEVICE_TREE is not set
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_GENERIC_ISA_DMA=y
+CONFIG_FSL_SOC=y
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0xc0000000
+CONFIG_BOOT_LOAD=0x00800000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+CONFIG_XFRM_USER=m
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_UB is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=32768
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=y
+CONFIG_SCSI_DMA=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=y
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+CONFIG_CHR_DEV_SG=y
+# CONFIG_CHR_DEV_SCH is not set
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
+
+#
+# SCSI Transports
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
+# CONFIG_SCSI_LOWLEVEL is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_NET_ETHERNET is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET_MII is not set
+# CONFIG_USB_USBNET is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_MPC52xx=y
+CONFIG_SERIAL_MPC52xx_CONSOLE=y
+CONFIG_SERIAL_MPC52xx_CONSOLE_BAUD=57600
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_WATCHDOG is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_NVRAM is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+CONFIG_I2C_MPC=y
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_SIMTEC is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_TINY_USB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_SENSORS_DS1337 is not set
+# CONFIG_SENSORS_DS1374 is not set
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_EEPROM is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_M41T00 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=m
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+
+#
+# Miscellaneous USB options
+#
+CONFIG_USB_DEVICEFS=y
+# CONFIG_USB_DEVICE_CLASS is not set
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_SUSPEND is not set
+# CONFIG_USB_PERSIST is not set
+# CONFIG_USB_OTG is not set
+
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_ISP116X_HCD is not set
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_HCD_PPC_SOC=y
+CONFIG_USB_OHCI_HCD_PPC_OF=y
+CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
+# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
+CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
+CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
+# CONFIG_USB_OHCI_LITTLE_ENDIAN is not set
+# CONFIG_USB_SL811_HCD is not set
+# CONFIG_USB_R8A66597_HCD is not set
+
+#
+# USB Device Class drivers
+#
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_PRINTER is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# may also be needed; see USB_STORAGE Help for more information
+#
+CONFIG_USB_STORAGE=y
+# CONFIG_USB_STORAGE_DEBUG is not set
+# CONFIG_USB_STORAGE_DATAFAB is not set
+# CONFIG_USB_STORAGE_FREECOM is not set
+# CONFIG_USB_STORAGE_DPCM is not set
+# CONFIG_USB_STORAGE_USBAT is not set
+# CONFIG_USB_STORAGE_SDDR09 is not set
+# CONFIG_USB_STORAGE_SDDR55 is not set
+# CONFIG_USB_STORAGE_JUMPSHOT is not set
+# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+# CONFIG_USB_MON is not set
+
+#
+# USB port drivers
+#
+
+#
+# USB Serial Converter support
+#
+# CONFIG_USB_SERIAL is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_AUERSWALD is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_PHIDGET is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
+
+#
+# USB DSL modem support
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4DEV_FS is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+CONFIG_NFS_V4=y
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+# CONFIG_SUNRPC_BIND34 is not set
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=y
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
+# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+
+#
+# Instrumentation Support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_BDI_SWITCH is not set
+# CONFIG_BOOTX_TEXT is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_MANAGER=y
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_WP512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+CONFIG_CRYPTO_ECB=m
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=m
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_XTS is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_TEST is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+CONFIG_CRYPTO_HW=y
+CONFIG_PPC_CLOCK=y
^ permalink raw reply related
* [PATCH v2 10/12] [POWERPC] Motion-PRO: Add LED support.
From: Marian Balakowicz @ 2007-11-03 23:53 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <20071103235210.31906.83423.stgit@hekate.izotz.org>
Add LED driver for Promess Motion-PRO board.
Signed-off-by: Jan Wrobel <wrr@semihalf.com>
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
---
drivers/leds/Kconfig | 7 +
drivers/leds/Makefile | 3 -
drivers/leds/leds-motionpro.c | 240 +++++++++++++++++++++++++++++++++++++++++
include/asm-powerpc/mpc52xx.h | 5 +
4 files changed, 254 insertions(+), 1 deletions(-)
create mode 100644 drivers/leds/leds-motionpro.c
diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index ec568fa..1567ed6 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -55,6 +55,13 @@ config LEDS_TOSA
This option enables support for the LEDs on Sharp Zaurus
SL-6000 series.
+config LEDS_MOTIONPRO
+ tristate "Motion-PRO LEDs Support"
+ depends on LEDS_CLASS && PPC_MPC5200
+ help
+ This option enables support for status and ready LEDs connected
+ to GPIO lines on Motion-PRO board.
+
config LEDS_S3C24XX
tristate "LED Support for Samsung S3C24XX GPIO LEDs"
depends on LEDS_CLASS && ARCH_S3C2410
diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
index a60de1b..a56d399 100644
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -18,7 +18,8 @@ obj-$(CONFIG_LEDS_H1940) += leds-h1940.o
obj-$(CONFIG_LEDS_COBALT_QUBE) += leds-cobalt-qube.o
obj-$(CONFIG_LEDS_COBALT_RAQ) += leds-cobalt-raq.o
obj-$(CONFIG_LEDS_GPIO) += leds-gpio.o
-obj-$(CONFIG_LEDS_CM_X270) += leds-cm-x270.o
+obj-$(CONFIG_LEDS_CM_X270) += leds-cm-x270.o
+obj-$(CONFIG_LEDS_MOTIONPRO) += leds-motionpro.o
# LED Triggers
obj-$(CONFIG_LEDS_TRIGGER_TIMER) += ledtrig-timer.o
diff --git a/drivers/leds/leds-motionpro.c b/drivers/leds/leds-motionpro.c
new file mode 100644
index 0000000..74b99aa
--- /dev/null
+++ b/drivers/leds/leds-motionpro.c
@@ -0,0 +1,240 @@
+/*
+ * LEDs driver for the Motion-PRO board.
+ *
+ * Copyright (C) 2007 Semihalf
+ * Jan Wrobel <wrr@semihalf.com>
+ * Marian Balakowicz <m8@semihalf.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc., 51
+ * Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ *
+ *
+ * Decription:
+ * This driver enables control over Motion-PRO status and ready LEDs through
+ * sysfs. LEDs can be controlled by writing to sysfs files:
+ * class/leds/<led-name>/(brightness|delay_off|delay_on).
+ * See Documentation/leds-class.txt for more details.
+ * <led-name> is the set to the corresponding GPT node name.
+ *
+ * Before user issues first control command via sysfs, LED blinking is
+ * controlled by the kernel ('blink-delay' property of the GPT node
+ * in the device tree blob).
+ *
+ */
+
+#undef DEBUG
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/leds.h>
+#include <linux/vmalloc.h>
+
+#include <asm/mpc52xx.h>
+#include <asm/io.h>
+#include <asm/of_platform.h>
+
+/* LED control bits */
+#define LED_ON MPC52xx_GPT_OUTPUT_1
+
+/* LED mode */
+#define LED_MODE_KERNEL 1
+#define LED_MODE_USER 2
+
+struct motionpro_led {
+ spinlock_t led_lock; /* Protects the LED data */
+ struct mpc52xx_gpt __iomem *gpt;/* LED registers */
+ struct timer_list blink_timer; /* Used if blink_delay is nonzero */
+ unsigned int blink_delay; /* [ms], if set to 0 blinking is off */
+ unsigned int mode; /* kernel/user */
+ struct led_classdev mpled_cdev; /* LED class */
+};
+
+/*
+ * Timer event - blinks LED before user takes control over it
+ * with the first access via sysfs.
+ */
+static void mpled_timer_toggle(unsigned long data)
+{
+ struct motionpro_led *mpled = (struct motionpro_led *) data;
+
+ spin_lock_bh(&mpled->led_lock);
+ if (mpled->mode == LED_MODE_KERNEL) {
+ u32 val = in_be32(&mpled->gpt->mode);
+ val ^= LED_ON;
+ out_be32(&mpled->gpt->mode, val);
+
+ mod_timer(&mpled->blink_timer,
+ jiffies + msecs_to_jiffies(mpled->blink_delay));
+ }
+ spin_unlock_bh(&mpled->led_lock);
+}
+
+/*
+ * Turn on/off led according to user settings in sysfs.
+ * First call to this function disables kernel blinking.
+ */
+static void mpled_set(struct led_classdev *led_cdev,
+ enum led_brightness brightness)
+{
+ struct motionpro_led *mpled;
+ int old_mode;
+ u32 val;
+
+ mpled = container_of(led_cdev, struct motionpro_led, mpled_cdev);
+
+ spin_lock_bh(&mpled->led_lock);
+ /* disable kernel controll */
+ old_mode = mpled->mode;
+ if (old_mode == LED_MODE_KERNEL)
+ mpled->mode = LED_MODE_USER;
+
+ val = in_be32(&mpled->gpt->mode);
+ if (brightness)
+ val |= LED_ON;
+ else
+ val &= ~LED_ON;
+ out_be32(&mpled->gpt->mode, val);
+ spin_unlock_bh(&mpled->led_lock);
+
+ /* delete kernel mode blink timer, not needed anymore */
+ if ((old_mode == LED_MODE_KERNEL) && mpled->blink_delay)
+ del_timer(&mpled->blink_timer);
+}
+
+static void mpled_init_led(void __iomem *gpt_mode)
+{
+ u32 val = in_be32(gpt_mode);
+ val |= MPC52xx_GPT_ENABLE_OUTPUT;
+ val &= ~LED_ON;
+ out_be32(gpt_mode, val);
+}
+
+static int __devinit mpled_probe(struct of_device *op, const struct of_device_id *match)
+{
+ struct motionpro_led *mpled;
+ const unsigned int *of_blink_delay = NULL;
+ int err = 0;
+
+ dev_dbg(&op->dev, "mpled_probe: node=%s (op=%p, match=%p)\n",
+ op->node->name, op, match);
+
+ mpled = kzalloc(sizeof(*mpled), GFP_KERNEL);
+ if (!mpled)
+ return -ENOMEM;
+
+ mpled->gpt = mpc52xx_map_node(op->node);
+ if (!mpled->gpt) {
+ printk(KERN_ERR __FILE__ ": "
+ "Error mapping GPT registers for LED %s\n",
+ op->node->name);
+ err = -EIO;
+ goto err_free;
+ }
+
+ /* initialize GPT for LED use */
+ mpled_init_led(&mpled->gpt->mode);
+
+ spin_lock_init(&mpled->led_lock);
+ mpled->mode = LED_MODE_KERNEL;
+
+ /* get 'blink-delay' property if present */
+ of_blink_delay = of_get_property(op->node, "blink-delay", NULL);
+ mpled->blink_delay = of_blink_delay ? *of_blink_delay : 0;
+ dev_dbg(&op->dev, "mpled_probe: blink_delay = %d msec\n",
+ mpled->blink_delay);
+
+ /* initialize kernel blink_timer if blink_delay was provided */
+ if (mpled->blink_delay) {
+ init_timer(&mpled->blink_timer);
+ mpled->blink_timer.function = mpled_timer_toggle;
+ mpled->blink_timer.data = (unsigned long)mpled;
+
+ mod_timer(&mpled->blink_timer,
+ jiffies + msecs_to_jiffies(mpled->blink_delay));
+ }
+
+ /* register LED classdev */
+ mpled->mpled_cdev.name = op->node->name;
+ mpled->mpled_cdev.brightness_set = mpled_set;
+ mpled->mpled_cdev.default_trigger = "timer";
+
+ if ((err = led_classdev_register(NULL, &mpled->mpled_cdev))) {
+ printk(KERN_ERR __FILE__ ": "
+ "Error registering class device for LED %s\n",
+ op->node->name);
+ goto err;
+ }
+
+ dev_set_drvdata(&op->dev, mpled);
+ return 0;
+
+err:
+ if (mpled->blink_delay)
+ del_timer(&mpled->blink_timer);
+ iounmap(mpled->gpt);
+err_free:
+ kfree(mpled);
+
+ return err;
+}
+
+static int mpled_remove(struct of_device *op)
+{
+ struct motionpro_led *mpled = dev_get_drvdata(&op->dev);
+
+ dev_dbg(&op->dev, "mpled_remove: (%p)\n", op);
+
+ if (mpled->blink_delay && (mpled->mode == LED_MODE_KERNEL))
+ del_timer(&mpled->blink_timer);
+
+ led_classdev_unregister(&mpled->mpled_cdev);
+
+ iounmap(mpled->gpt);
+ kfree(mpled);
+
+ return 0;
+}
+
+static struct of_device_id mpled_match[] = {
+ { .compatible = "promess,motionpro-readyled", },
+ { .compatible = "promess,motionpro-statusled", },
+ {},
+};
+
+static struct of_platform_driver mpled_driver = {
+ .owner = THIS_MODULE,
+ .name = "leds-motionpro",
+ .match_table = mpled_match,
+ .probe = mpled_probe,
+ .remove = mpled_remove,
+};
+
+static int __init mpled_init(void)
+{
+ return of_register_platform_driver(&mpled_driver);
+}
+
+static void __exit mpled_exit(void)
+{
+ of_unregister_platform_driver(&mpled_driver);
+}
+
+module_init(mpled_init);
+module_exit(mpled_exit);
+
+MODULE_LICENSE("GPL")
+MODULE_DESCRIPTION("Motion-PRO LED driver");
+MODULE_AUTHOR("Jan Wrobel <wrr@semihalf.com>");
+MODULE_AUTHOR("Marian Balakowicz <m8@semihalf.com>");
diff --git a/include/asm-powerpc/mpc52xx.h b/include/asm-powerpc/mpc52xx.h
index 1887b13..d8e4ada 100644
--- a/include/asm-powerpc/mpc52xx.h
+++ b/include/asm-powerpc/mpc52xx.h
@@ -147,6 +147,11 @@ struct mpc52xx_gpio {
#define MPC52xx_GPIO_PSC_CONFIG_UART_WITH_CD 5
#define MPC52xx_GPIO_PCI_DIS (1<<15)
+/* Enables GPT register to operate as simple GPIO output register */
+#define MPC52xx_GPT_ENABLE_OUTPUT 0x00000024
+/* Puts 1 on GPT output pin */
+#define MPC52xx_GPT_OUTPUT_1 0x00000010
+
/* GPIO with WakeUp*/
struct mpc52xx_gpio_wkup {
u8 wkup_gpioe; /* GPIO_WKUP + 0x00 */
^ permalink raw reply related
* [PATCH v2 11/12] [POWERPC] Promess Motion-PRO DTS
From: Marian Balakowicz @ 2007-11-03 23:53 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <20071103235210.31906.83423.stgit@hekate.izotz.org>
Add device tree source file for Motion-PRO board.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
---
arch/powerpc/boot/dts/motionpro.dts | 323 +++++++++++++++++++++++++++++++++++
1 files changed, 323 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/boot/dts/motionpro.dts
diff --git a/arch/powerpc/boot/dts/motionpro.dts b/arch/powerpc/boot/dts/motionpro.dts
new file mode 100644
index 0000000..82212d9
--- /dev/null
+++ b/arch/powerpc/boot/dts/motionpro.dts
@@ -0,0 +1,323 @@
+/*
+ * Motion-PRO board Device Tree Source
+ *
+ * Copyright (C) 2007 Semihalf
+ * Marian Balakowicz <m8@semihalf.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/*
+ * WARNING: Do not depend on this tree layout remaining static just yet.
+ * The MPC5200 device tree conventions are still in flux
+ * Keep an eye on the linuxppc-dev mailing list for more details
+ */
+
+/ {
+ model = "promess,motionpro";
+ compatible = "promess,motionpro","mpc5200-simple-platform";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,5200@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <20>;
+ i-cache-line-size = <20>;
+ d-cache-size = <4000>; // L1, 16K
+ i-cache-size = <4000>; // L1, 16K
+ timebase-frequency = <0>; // from bootloader
+ bus-frequency = <0>; // from bootloader
+ clock-frequency = <0>; // from bootloader
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <00000000 04000000>; // 64MB
+ };
+
+ soc5200@f0000000 {
+ model = "fsl,mpc5200b";
+ compatible = "mpc5200";
+ revision = ""; // from bootloader
+ device_type = "soc";
+ ranges = <0 f0000000 0000c000>;
+ reg = <f0000000 00000100>;
+ bus-frequency = <0>; // from bootloader
+ system-frequency = <0>; // from bootloader
+
+ cdm@200 {
+ compatible = "mpc5200b-cdm","mpc5200-cdm";
+ reg = <200 38>;
+ };
+
+ mpc5200_pic: pic@500 {
+ // 5200 interrupts are encoded into two levels;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ device_type = "interrupt-controller";
+ compatible = "mpc5200b-pic","mpc5200-pic";
+ reg = <500 80>;
+ };
+
+ gpt@600 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ cell-index = <0>;
+ reg = <600 10>;
+ interrupts = <1 9 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ fsl,has-wdt;
+ };
+
+ gpt@610 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ cell-index = <1>;
+ reg = <610 10>;
+ interrupts = <1 a 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ gpt@620 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ cell-index = <2>;
+ reg = <620 10>;
+ interrupts = <1 b 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ gpt@630 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ cell-index = <3>;
+ reg = <630 10>;
+ interrupts = <1 c 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ gpt@640 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ cell-index = <4>;
+ reg = <640 10>;
+ interrupts = <1 d 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ gpt@650 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ cell-index = <5>;
+ reg = <650 10>;
+ interrupts = <1 e 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ motionpro-statusled@660 { // Motion-PRO status LED
+ compatible = "promess,motionpro-statusled";
+ cell-index = <6>;
+ reg = <660 10>;
+ interrupts = <1 f 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ blink-delay = <64>; // 100 msec
+ };
+
+ motionpro-readyled@670 { // Motion-PRO ready LED
+ compatible = "promess,motionpro-readyled";
+ cell-index = <7>;
+ reg = <670 10>;
+ interrupts = <1 10 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ rtc@800 { // Real time clock
+ compatible = "mpc5200b-rtc","mpc5200-rtc";
+ device_type = "rtc";
+ reg = <800 100>;
+ interrupts = <1 5 0 1 6 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ mscan@980 {
+ compatible = "mpc5200b-mscan","mpc5200-mscan";
+ cell-index = <1>;
+ interrupts = <2 12 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ reg = <980 80>;
+ };
+
+ gpio@b00 {
+ compatible = "mpc5200b-gpio","mpc5200-gpio";
+ reg = <b00 40>;
+ interrupts = <1 7 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ gpio-wkup@c00 {
+ compatible = "mpc5200b-gpio-wkup","mpc5200-gpio-wkup";
+ reg = <c00 40>;
+ interrupts = <1 8 0 0 3 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+
+ spi@f00 {
+ device_type = "spi";
+ compatible = "mpc5200b-spi","mpc5200-spi";
+ reg = <f00 20>;
+ interrupts = <2 d 0 2 e 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ usb@1000 {
+ device_type = "usb-ohci-be";
+ compatible = "mpc5200b-ohci","mpc5200-ohci","ohci-be";
+ reg = <1000 ff>;
+ interrupts = <2 6 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ dma-controller@1200 {
+ compatible = "mpc5200b-bestcomm","mpc5200-bestcomm";
+ reg = <1200 80>;
+ interrupts = <3 0 0 3 1 0 3 2 0 3 3 0
+ 3 4 0 3 5 0 3 6 0 3 7 0
+ 3 8 0 3 9 0 3 a 0 3 b 0
+ 3 c 0 3 d 0 3 e 0 3 f 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ xlb@1f00 {
+ compatible = "mpc5200b-xlb","mpc5200-xlb";
+ reg = <1f00 100>;
+ };
+
+ serial@2000 { // PSC1
+ device_type = "serial";
+ compatible = "mpc5200b-psc-uart","mpc5200-psc-uart";
+ port-number = <0>; // Logical port assignment
+ cell-index = <0>;
+ reg = <2000 100>;
+ interrupts = <2 1 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ // PSC2 in spi master mode
+ spi@2200 { // PSC2
+ device_type = "spi";
+ compatible = "mpc5200b-psc-spi","mpc5200-psc-spi";
+ cell-index = <1>;
+ reg = <2200 100>;
+ interrupts = <2 2 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ // PSC5 in uart mode
+ serial@2800 { // PSC5
+ device_type = "serial";
+ compatible = "mpc5200b-psc-uart","mpc5200-psc-uart";
+ port-number = <4>; // Logical port assignment
+ cell-index = <4>;
+ reg = <2800 100>;
+ interrupts = <2 c 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ ethernet@3000 {
+ device_type = "network";
+ compatible = "mpc5200b-fec","mpc5200-fec";
+ reg = <3000 800>;
+ local-mac-address = [ 00 00 00 00 00 00 ]; /* Filled in by U-Boot */
+ interrupts = <2 5 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ ata@3a00 {
+ compatible = "mpc5200b-ata","mpc5200-ata";
+ reg = <3a00 100>;
+ interrupts = <2 7 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ i2c@3d40 {
+ device_type = "i2c";
+ compatible = "mpc5200b-i2c","mpc5200-i2c","fsl-i2c";
+ reg = <3d40 40>;
+ interrupts = <2 10 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ fsl5200-clocking;
+ };
+
+ sram@8000 {
+ compatible = "mpc5200b-sram","mpc5200-sram","sram";
+ reg = <8000 4000>;
+ };
+ };
+
+ lpb {
+ model = "fsl,lpb";
+ compatible = "fsl,lpb";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <50000000 50000000 00030000
+ ff000000 ff000000 01000000>;
+
+ // 8-bit DualPort SRAM on LocalPlus Bus CS1
+ kollmorgen@50000000 {
+ compatible = "promess,motionpro-kollmorgen";
+ reg = <50000000 ffff>;
+ interrupts = <1 1 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ };
+
+ // 8-bit board CPLD on LocalPlus Bus CS2
+ cpld@50010000 {
+ compatible = "promess,motionpro-cpld";
+ reg = <50010000 ffff>;
+ };
+
+ // 8-bit custom Anybus Module on LocalPlus Bus CS3
+ anybus50020000 {
+ compatible = "promess,motionpro-anybus";
+ reg = <50020000 ffff>;
+ };
+ pro_module_general@50020000 {
+ compatible = "promess,pro_module_general";
+ reg = <50020000 3>;
+ };
+ pro_module_dio@50020800 {
+ compatible = "promess,pro_module_dio";
+ reg = <50020800 2>;
+ };
+ };
+
+ pci@f0000d00 {
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ compatible = "mpc5200b-pci","mpc5200-pci";
+ reg = <f0000d00 100>;
+ interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map = <c000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot
+ c000 0 0 2 &mpc5200_pic 1 1 3
+ c000 0 0 3 &mpc5200_pic 1 2 3
+ c000 0 0 4 &mpc5200_pic 1 3 3
+
+ c800 0 0 1 &mpc5200_pic 1 1 3 // 2nd slot
+ c800 0 0 2 &mpc5200_pic 1 2 3
+ c800 0 0 3 &mpc5200_pic 1 3 3
+ c800 0 0 4 &mpc5200_pic 0 0 3>;
+ clock-frequency = <0>; // From boot loader
+ interrupts = <2 8 0 2 9 0 2 a 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ bus-range = <0 0>;
+ ranges = <42000000 0 80000000 80000000 0 20000000
+ 02000000 0 a0000000 a0000000 0 10000000
+ 01000000 0 00000000 b0000000 0 01000000>;
+ };
+};
^ permalink raw reply related
* [PATCH v2 12/12] [POWERPC] Promess Motion-PRO defconfig
From: Marian Balakowicz @ 2007-11-03 23:53 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <20071103235210.31906.83423.stgit@hekate.izotz.org>
Add Motion-PRO board defconfig file.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
---
arch/powerpc/configs/motionpro_defconfig | 989 ++++++++++++++++++++++++++++++
1 files changed, 989 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/configs/motionpro_defconfig
diff --git a/arch/powerpc/configs/motionpro_defconfig b/arch/powerpc/configs/motionpro_defconfig
new file mode 100644
index 0000000..fd7a327
--- /dev/null
+++ b/arch/powerpc/configs/motionpro_defconfig
@@ -0,0 +1,989 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.23
+# Mon Oct 29 14:11:27 2007
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+CONFIG_6xx=y
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_PPC_FPU=y
+# CONFIG_ALTIVEC is not set
+CONFIG_PPC_STD_MMU=y
+CONFIG_PPC_STD_MMU_32=y
+# CONFIG_PPC_MM_SLICES is not set
+# CONFIG_SMP is not set
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+# CONFIG_PPC_UDBG_16550 is not set
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+# CONFIG_SYSCTL_SYSCALL is not set
+# CONFIG_KALLSYMS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+# CONFIG_EPOLL is not set
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+# CONFIG_KMOD is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# Platform support
+#
+CONFIG_PPC_MULTIPLATFORM=y
+# CONFIG_PPC_82xx is not set
+# CONFIG_PPC_83xx is not set
+# CONFIG_PPC_86xx is not set
+CONFIG_CLASSIC32=y
+# CONFIG_PPC_CHRP is not set
+CONFIG_PPC_MPC52xx=y
+CONFIG_PPC_MPC5200=y
+# CONFIG_PPC_MPC5200_BUGFIX is not set
+CONFIG_PPC_MPC5200_SIMPLE=y
+# CONFIG_PPC_EFIKA is not set
+# CONFIG_PPC_LITE5200 is not set
+# CONFIG_PPC_PMAC is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+# CONFIG_EMBEDDED6xx is not set
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_TAU is not set
+# CONFIG_CPM2 is not set
+# CONFIG_FSL_ULI1575 is not set
+# CONFIG_PPC_BESTCOMM is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+# CONFIG_KEXEC is not set
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+CONFIG_PROC_DEVICETREE=y
+# CONFIG_CMDLINE_BOOL is not set
+CONFIG_PM=y
+# CONFIG_PM_LEGACY is not set
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_SUSPEND=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
+# CONFIG_HIBERNATION is not set
+CONFIG_SECCOMP=y
+# CONFIG_WANT_DEVICE_TREE is not set
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_GENERIC_ISA_DMA=y
+CONFIG_FSL_SOC=y
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0xc0000000
+CONFIG_BOOT_LOAD=0x00800000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+CONFIG_XFRM_USER=m
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+CONFIG_MTD_RAM=y
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=32768
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=y
+CONFIG_SCSI_DMA=y
+CONFIG_SCSI_TGT=y
+# CONFIG_SCSI_NETLINK is not set
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=y
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+CONFIG_CHR_DEV_SG=y
+# CONFIG_CHR_DEV_SCH is not set
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
+
+#
+# SCSI Transports
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
+CONFIG_SCSI_LOWLEVEL=y
+# CONFIG_ISCSI_TCP is not set
+# CONFIG_SCSI_DEBUG is not set
+CONFIG_ATA=y
+# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_PATA_MPC52xx=y
+CONFIG_PATA_PLATFORM=y
+# CONFIG_MD is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_B44 is not set
+CONFIG_NETDEV_1000=y
+# CONFIG_MV643XX_ETH is not set
+CONFIG_NETDEV_10000=y
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_MPC52xx=y
+CONFIG_SERIAL_MPC52xx_CONSOLE=y
+CONFIG_SERIAL_MPC52xx_CONSOLE_BAUD=115200
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_WATCHDOG is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_NVRAM is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+CONFIG_I2C_MPC=y
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_SIMTEC is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_SENSORS_DS1337 is not set
+# CONFIG_SENSORS_DS1374 is not set
+# CONFIG_DS1682 is not set
+CONFIG_SENSORS_EEPROM=y
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_M41T00 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_AD7418 is not set
+# CONFIG_SENSORS_ADM1021 is not set
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1029 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ADT7470 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_F75375S is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM75 is not set
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_LM93 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_MAX6650 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_DME1737 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47M192 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83791D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=m
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+# CONFIG_USB is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+# CONFIG_MMC is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+
+#
+# LED drivers
+#
+CONFIG_LEDS_MOTIONPRO=y
+
+#
+# LED Triggers
+#
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+# CONFIG_LEDS_TRIGGER_HEARTBEAT is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4DEV_FS is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS2_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+CONFIG_NFS_V4=y
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+# CONFIG_SUNRPC_BIND34 is not set
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=y
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
+# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+
+#
+# Instrumentation Support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_BDI_SWITCH is not set
+# CONFIG_BOOTX_TEXT is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_MANAGER=y
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_WP512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+CONFIG_CRYPTO_ECB=m
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=m
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_XTS is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_TEST is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+CONFIG_CRYPTO_HW=y
+CONFIG_PPC_CLOCK=y
^ permalink raw reply related
* use of aliases in device trees
From: Kumar Gala @ 2007-11-04 1:02 UTC (permalink / raw)
To: linux-ppc list; +Cc: U-Boot Users List
In some discussion on the u-boot dev list it became clear that having
aliases in the device tree might be useful as a common way to deal
with finding specific nodes that need fixing up by the firmware.
This problem also exists in the kernel bootwrappers.
The common example is how to associate a given MAC address with the
proper ethernet node. In u-boot an explicit path is hard coded into
the u-boot build for each ethernet device. In the bootwrapper we use
"linux,network-index = <N>" in the given ethernet node.
One common solution would be having a top level aliases like the pmac
tree's have:
aliases {
enet0 = "...";
enet1 = "...";
pci0 = "...";
pci1 = "...";
};
I wanted to see what people think of this idea and about trying to
use common names for the aliases? If nothing else I believe we will
look at doing this on the FSL boards/parts.
- k
^ permalink raw reply
* [PATCH] [POWERPC] iSeries_init_IRQ non-PCI tidy
From: Stephen Rothwell @ 2007-11-04 2:22 UTC (permalink / raw)
To: paulus; +Cc: ppc-dev
ppc_md.init_IRQ is not called if it is NULL, so we don't need an empty
routine in the non PCI case.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
---
arch/powerpc/platforms/iseries/irq.h | 4 ++++
arch/powerpc/platforms/iseries/setup.c | 4 ----
2 files changed, 4 insertions(+), 4 deletions(-)
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
diff --git a/arch/powerpc/platforms/iseries/irq.h b/arch/powerpc/platforms/iseries/irq.h
index 69f1b43..a1c2360 100644
--- a/arch/powerpc/platforms/iseries/irq.h
+++ b/arch/powerpc/platforms/iseries/irq.h
@@ -1,9 +1,13 @@
#ifndef _ISERIES_IRQ_H
#define _ISERIES_IRQ_H
+#ifdef CONFIG_PCI
extern void iSeries_init_IRQ(void);
extern int iSeries_allocate_IRQ(HvBusNumber, HvSubBusNumber, u32);
extern void iSeries_activate_IRQs(void);
+#else
+#define iSeries_init_IRQ NULL
+#endif
extern unsigned int iSeries_get_irq(void);
#endif /* _ISERIES_IRQ_H */
diff --git a/arch/powerpc/platforms/iseries/setup.c b/arch/powerpc/platforms/iseries/setup.c
index 37ae07e..0877a88 100644
--- a/arch/powerpc/platforms/iseries/setup.c
+++ b/arch/powerpc/platforms/iseries/setup.c
@@ -617,10 +617,6 @@ static void iseries_dedicated_idle(void)
}
}
-#ifndef CONFIG_PCI
-void __init iSeries_init_IRQ(void) { }
-#endif
-
static void __iomem *iseries_ioremap(phys_addr_t address, unsigned long size,
unsigned long flags)
{
--
1.5.3.5
^ permalink raw reply related
* [PATCH] [POWERPC] Fix link errors for allyesconfig
From: Stephen Rothwell @ 2007-11-04 2:28 UTC (permalink / raw)
To: paulus; +Cc: ppc-dev, David S. Miller
An allyesconfig build creates a .text section that is so big that the
.text.init.refok and .fixup sections are too far away for the relocations
to be fixed up correctly. This patch fixes that by linking all the
relevent text sections for each file together.
Suggested by Paul Mackerras.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
---
arch/powerpc/kernel/vmlinux.lds.S | 3 +--
1 files changed, 1 insertions(+), 2 deletions(-)
This still leaves us with the problem that the TOC overflows.
Dave, would something like this help as an alternative to the .fixup
change you committed recently?
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
diff --git a/arch/powerpc/kernel/vmlinux.lds.S b/arch/powerpc/kernel/vmlinux.lds.S
index 823a8cb..f66fa5d 100644
--- a/arch/powerpc/kernel/vmlinux.lds.S
+++ b/arch/powerpc/kernel/vmlinux.lds.S
@@ -37,11 +37,10 @@ SECTIONS
ALIGN_FUNCTION();
*(.text.head)
_text = .;
- TEXT_TEXT
+ *(.text .fixup .text.init.refok .exit.text.refok)
SCHED_TEXT
LOCK_TEXT
KPROBES_TEXT
- *(.fixup)
#ifdef CONFIG_PPC32
*(.got1)
--
1.5.3.5
^ permalink raw reply related
* Re: 2.6.24-rc1 freezes on powerbook at first boot stage
From: Nathan Lynch @ 2007-11-04 3:20 UTC (permalink / raw)
To: Elimar Riesebieter; +Cc: linuxppc-dev, Linux Kernel Mailing List
In-Reply-To: <20071024124109.GA9442@frodo.home.lxtec.de>
(cc'ing linuxppc-dev, see
http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg221770.html
for original post and .config)
Elimar Riesebieter wrote:
> On Wed, 24 Oct 2007 the mental interface of
> Elimar Riesebieter told:
>
> [...]
> > The kernel is loaded from firmware but freezes at the moment to load
> > the radeon framebuffer. I can't get any debug info (don't know
> > how?).
>
> Screen dump till freeze:
>
> Using PowerMac machine description
> Total memory = 1024MB; using 2048kB for hash table (at cfe00000)
> Linux version 2.6.24-rc1-aragorn (riesebie@aragorn) (gcc version 4.2.3 20071014 (prelelease) (Debian 4.2.2-3)) #1 Wed Oct 24 12:48:27 CEST 2007
> Found UniNorth memory controller & host bridge @ 0xf8000000 revision: 0xd2
> Mapped at 0xfdfc0000
> Found a Intrepid mac-io controller, rev: 0, mapped at 0xfdf40000
> PowerMac motherboard: PowerBook G4 15"
> console [udbg0] enabled
> setup_arch: bootmem
> Found UniNorth PCI host bridge at 0x00000000f0000000. Firmware bus number: 0->1
> Found UniNorth PCI host bridge at 0x00000000f2000000. Firmware bus number: 0->1
> Found UniNorth PCI host bridge at 0x00000000f4000000. Firmware bus number: 0->1
> via-pmu: Server Mode is disabled
> PMU driver v2 initialized for Core99, firmware: 0c
> nvram: Checking bank 0...
> nvram: gen0=741, gen1=740
> nvram: Active bank is: 0
> nvram: OF partition at 0x410
> nvram: XP partition at 0x1020
> nvram: NR partition at 0x1120
> arch: exit
> Zone PFN ranges:
> DMA 0 -> 196608
> Normal 196608 -> 196608
> HighMem 196608 -> 262144
> Movable zone start PFN for each node
> early_node_map[1] active PFN ranges
> 0: 0 -> 262144
> Built 1 zonelists in Zone order. Total pages: 260096
> Kernel command line: root=/pci@f4000000/ata-6@d/disk@0:5 root=/dev/hda5
> mpic: Setting up MPIC " MPIC 1 " version 1.2 at 80040000, max 4 CPUs
> mpic: ISU size: 64, shift: 6, mask: 3f
> mpic: Initializing for 64 sources
> PID hash table entries: 4096 (order: 12, 16384 bytes)
> GMT Delta read from XPRAM: 0 minutes, DST: off
> clocksource: timebase mult[d9038e4] shift [22] registered
> clockevent: decremeter mult[4b7] shift[16] cpu[0]
> Console: colour dummy device 80x25
> console handover: boot [udbg0] -> real [tty0]
Does 2.6.23 (or any earlier kernel) work?
^ permalink raw reply
* Re: [U-Boot-Users] use of aliases in device trees
From: Grant Likely @ 2007-11-04 3:29 UTC (permalink / raw)
To: Kumar Gala; +Cc: linux-ppc list, David Gibson, U-Boot Users List
In-Reply-To: <DD2A9B2C-5D35-4F53-8542-3470C6FA5265@kernel.crashing.org>
On 11/3/07, Kumar Gala <galak@kernel.crashing.org> wrote:
> In some discussion on the u-boot dev list it became clear that having
> aliases in the device tree might be useful as a common way to deal
> with finding specific nodes that need fixing up by the firmware.
> This problem also exists in the kernel bootwrappers.
>
> The common example is how to associate a given MAC address with the
> proper ethernet node. In u-boot an explicit path is hard coded into
> the u-boot build for each ethernet device. In the bootwrapper we use
> "linux,network-index = <N>" in the given ethernet node.
>
> One common solution would be having a top level aliases like the pmac
> tree's have:
>
> aliases {
> enet0 = "...";
> enet1 = "...";
> pci0 = "...";
> pci1 = "...";
> };
One question to ask is do we use full paths or phandles to point at nodes?
OF, of course, uses full paths, but that does require more memory and
processing power, but it might not be significant enough to worry
about.
If we use phandles, then we should use names that don't conflict with
full path alias names. It would also be desirable to be able to
generate a phandle alias from the full path alias in order to maintain
some level of compatibility with OF. It also think it will make
maintaining aliases in .dts files simpler because trivial changes to
node paths won't break the phandle alias.
Maybe something like:
aliases {
enet0,phandle = <&enet0>;
enet1,phandle = <&enet1>;
...
};
Cheers,
g.
>
> I wanted to see what people think of this idea and about trying to
> use common names for the aliases? If nothing else I believe we will
> look at doing this on the FSL boards/parts.
>
> - k
>
> -------------------------------------------------------------------------
> This SF.net email is sponsored by: Splunk Inc.
> Still grepping through log files to find problems? Stop.
> Now Search log events and configuration files using AJAX and a browser.
> Download your FREE copy of Splunk now >> http://get.splunk.com/
> _______________________________________________
> U-Boot-Users mailing list
> U-Boot-Users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/u-boot-users
>
--
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
grant.likely@secretlab.ca
(403) 399-0195
^ permalink raw reply
* Re: [PATCH] net: Add 405EX support to new EMAC driver
From: Benjamin Herrenschmidt @ 2007-11-04 3:37 UTC (permalink / raw)
To: Olof Johansson; +Cc: netdev, Stefan Roese, linuxppc-dev
In-Reply-To: <20071102160304.GA5277@lixom.net>
On Fri, 2007-11-02 at 11:03 -0500, Olof Johansson wrote:
> On Fri, Nov 02, 2007 at 08:14:43AM +0100, Stefan Roese wrote:
> > This patch adds support for the 405EX to the new EMAC driver. Some as on
> > AXON, the 405EX handles the MDIO via the RGMII bridge.
>
> Hi,
>
> This isn't feedback on your patch as much as on "new-emac" in general:
>
> Isn't this the case where there should really be device tree properties
> instead? If you had an "ibm,emac-has-axon-stacr" property in the device
> node, then you don't have to modify the driver for every new board out
> there. Same for the other device properties, of course.
>
> I thought this was what having the device tree was all about. :(
Somewhat yeah. There are subtle variations here or there we haven't
totally indenfified... It might be a better option in our case here to
add "has-mdio" to the rgmii nodes indeed.
Part of the problem with those cells is that the chip folks keep
changing things subtly from one rev to another though, it's not even
totally clear to me yet whether the RGMII registers are totally
compatible betwee axon and 405ex, which is why I've pretty much stuck to
"compatible" properties to identify the variants.
The device-tree can do both. It's still better than no device-tree since
at least you know what cell variant is in there.
As for the STACR, Axon isn't the first one to have that bit flipped, I
think we should name the property differently, something like
"stacr-oc-inverted".
We can still use properties that way for new things in fact. As for EMAC
on cell, well, I can always put some fixup somewhere.
Ben.
^ permalink raw reply
* Re: radeon boot "hot-crash"
From: Benjamin Herrenschmidt @ 2007-11-04 3:39 UTC (permalink / raw)
To: Michael Buesch; +Cc: linuxppc-dev
In-Reply-To: <200711021955.49169.mb@bu3sch.de>
On Fri, 2007-11-02 at 19:55 +0100, Michael Buesch wrote:
> Hi,
>
> I'm wondering how we are finally going to fix my radeon
> "hot-crash" issue.
> Fact is, applying the patch below fixes the issue.
And will break somebody else ...
> Though, I see that this is not the correct patch to fix it.
> Other devices might need the register write which is removed here.
> So what about the following:
> We add a specialcase for the exact type (and revision and so on)
> for my chip here.
> How do find out what's my chiprevision?
> What exactly should be checked for here, so that only this chip
> is affected by the workaround?
I think best is to check for the specific machine. What powerbook model
is this ?
Ben.
>
> Index: wireless-2.6/drivers/video/aty/radeon_i2c.c
> ===================================================================
> --- wireless-2.6.orig/drivers/video/aty/radeon_i2c.c 2007-10-17 18:03:10.000000000 +0200
> +++ wireless-2.6/drivers/video/aty/radeon_i2c.c 2007-10-17 18:18:52.000000000 +0200
> @@ -137,13 +137,7 @@ void radeon_delete_i2c_busses(struct rad
> int radeon_probe_i2c_connector(struct radeonfb_info *rinfo, int conn,
> u8 **out_edid)
> {
> - u32 reg = rinfo->i2c[conn-1].ddc_reg;
> - u8 *edid;
> -
> - OUTREG(reg, INREG(reg) &
> - ~(VGA_DDC_DATA_OUTPUT | VGA_DDC_CLK_OUTPUT));
> -
> - edid = fb_ddc_read(&rinfo->i2c[conn-1].adapter);
> + u8 *edid = fb_ddc_read(&rinfo->i2c[conn-1].adapter);
>
> if (out_edid)
> *out_edid = edid;
>
^ permalink raw reply
* Re: [PATCH] [POWERPC] Fix link errors for allyesconfig
From: David Miller @ 2007-11-04 3:47 UTC (permalink / raw)
To: sfr; +Cc: linuxppc-dev, paulus
In-Reply-To: <20071104132839.ea04cf6b.sfr@canb.auug.org.au>
From: Stephen Rothwell <sfr@canb.auug.org.au>
Date: Sun, 4 Nov 2007 13:28:39 +1100
> An allyesconfig build creates a .text section that is so big that the
> .text.init.refok and .fixup sections are too far away for the relocations
> to be fixed up correctly. This patch fixes that by linking all the
> relevent text sections for each file together.
>
> Suggested by Paul Mackerras.
>
> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
> ---
> arch/powerpc/kernel/vmlinux.lds.S | 3 +--
> 1 files changed, 1 insertions(+), 2 deletions(-)
>
> This still leaves us with the problem that the TOC overflows.
>
> Dave, would something like this help as an alternative to the .fixup
> change you committed recently?
It might, I'll make some tests when I get a chance.
Thanks for pointing this out Stephen.
^ permalink raw reply
* Re: [PATCH v2 05/12] [POWERPC] Export mpc52xx_map_node() routine symbol
From: Stephen Rothwell @ 2007-11-04 4:09 UTC (permalink / raw)
To: Marian Balakowicz; +Cc: linuxppc-dev
In-Reply-To: <20071103235240.31906.93311.stgit@hekate.izotz.org>
[-- Attachment #1: Type: text/plain, Size: 627 bytes --]
Hi Marian,
On Sun, 04 Nov 2007 00:52:40 +0100 Marian Balakowicz <m8@semihalf.com> wrote:
>
> -static void __iomem *
> +void __iomem *
> mpc52xx_map_node(struct device_node *ofn)
> {
> const u32 *regaddr_p;
> @@ -48,6 +48,8 @@ mpc52xx_map_node(struct device_node *ofn)
> return ioremap((u32)regaddr64, (u32)size64);
> }
>
> +EXPORT_SYMBOL(mpc52xx_map_node);
> +
We generally don't leave a blank line between a function an its
EXPORT_SYMBOL(). Also, any reason not to use EXPORT_SYMBOL_GPL?
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
http://www.canb.auug.org.au/~sfr/
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply
* Re: [PATCH v2 10/12] [POWERPC] Motion-PRO: Add LED support.
From: Stephen Rothwell @ 2007-11-04 4:27 UTC (permalink / raw)
To: Marian Balakowicz; +Cc: linuxppc-dev
In-Reply-To: <20071103235311.31906.23754.stgit@hekate.izotz.org>
[-- Attachment #1: Type: text/plain, Size: 1911 bytes --]
Hi Marian,
On Sun, 04 Nov 2007 00:53:11 +0100 Marian Balakowicz <m8@semihalf.com> wrote:
>
> +++ b/drivers/leds/leds-motionpro.c
> @@ -0,0 +1,240 @@
> +
> +#include <linux/module.h>
> +#include <linux/types.h>
> +#include <linux/kernel.h>
> +#include <linux/platform_device.h>
> +#include <linux/leds.h>
> +#include <linux/vmalloc.h>
> +
> +#include <asm/mpc52xx.h>
> +#include <asm/io.h>
> +#include <asm/of_platform.h>
You want <linux/of_platform.h> instead of <asm/..> and probably not
<linux/platform_device.h> above.
> +static void mpled_timer_toggle(unsigned long data)
> +{
> + struct motionpro_led *mpled = (struct motionpro_led *) data;
^
Unnecessary space.
> +static int __devinit mpled_probe(struct of_device *op, const struct of_device_id *match)
Split this line.
> +{
> + struct motionpro_led *mpled;
> + const unsigned int *of_blink_delay = NULL;
You don't need to initialise this as you assign it before you use it.
> + int err = 0;
Same here.
> + if ((err = led_classdev_register(NULL, &mpled->mpled_cdev))) {
We would normally do the assignment separately from the check, so:
err = led_classdev_register(NULL, &mpled->mpled_cdev);
if (err) {
> +static struct of_platform_driver mpled_driver = {
> + .owner = THIS_MODULE,
> + .name = "leds-motionpro",
> + .match_table = mpled_match,
> + .probe = mpled_probe,
> + .remove = mpled_remove,
> +};
You should now use the name and owner fields of the embedded struct
device_driver, so:
static struct of_platform_driver mpled_driver = {
.match_table = mpled_match,
.probe = mpled_probe,
.remove = mpled_remove,
.driver = {
.owner = THIS_MODULE,
.name = "leds-motionpro",
},
};
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
http://www.canb.auug.org.au/~sfr/
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply
* Re: [PATCH v2] pcmcia: Remove replace kio_addr_t with unsigned int everywhere
From: Komuro @ 2007-11-04 9:11 UTC (permalink / raw)
To: Olof Johansson
Cc: Matthew Wilcox, linux-pcmcia, linux-kernel, linuxppc-dev,
Andrew Morton, Christoph Hellwig, Alan Cox
In-Reply-To: <20071028201858.GA10048@lixom.net>
Hi,
It should be "unsigned long" instead of "unsigned int".
64bit architecture uses 64bit-Memory-mapped-IO.
Best Regards
Komuro
>
>
>pcmcia: Remove replace kio_addr_t with unsigned int everywhere
>
>Remove kio_addr_t, and replace it with unsigned int. No known architecture
>needs more than 32 bits for IO addresses and ports and having a separate
>type for it is just messy.
>
>This goes on top of the patch switching the io_req_t members from ioaddr_t
>to unsigned int.
>
>
>Signed-off-by: Olof Johansson <olof@lixom.net>
>
>---
>
>On Sun, Oct 28, 2007 at 03:10:34PM -0500, Olof Johansson wrote:
>
>> This goes on top of the patch switching the io_req_t members from ioaddr_t
>> to unsigned int.
>
>Crap, I had an old version of that patch as base in my local tree when I did
>these edits. Here's a proper version.
>
>-Olof
>
^ permalink raw reply
* Re: use of aliases in device trees
From: Segher Boessenkool @ 2007-11-04 9:24 UTC (permalink / raw)
To: Kumar Gala; +Cc: linux-ppc list, U-Boot Users List
In-Reply-To: <DD2A9B2C-5D35-4F53-8542-3470C6FA5265@kernel.crashing.org>
> In some discussion on the u-boot dev list it became clear that having
> aliases in the device tree might be useful as a common way to deal
> with finding specific nodes that need fixing up by the firmware.
> One common solution would be having a top level aliases like the pmac
> tree's have:
>
> aliases {
> enet0 = "...";
> enet1 = "...";
> pci0 = "...";
> pci1 = "...";
> };
It's not just Apple that uses this; this is standard OF stuff.
> I wanted to see what people think of this idea and about trying to
> use common names for the aliases?
I'm obviously all for it, having suggested it myself a few times.
For common names, I think a good starting point would be to use
the generic names (as defined in the "generic names" recommended
practice; this should be the name of the nodes pointed to as well),
followed by a number; and/or a generic name without any suffix,
which points to the "main" device of that type.
This is a lot like your example, except that "enet" isn't a generic
name (that would be "network" I believe). It is perfectly fine to
have to or more aliases pointing to the same node though.
This won't solve all identification problems of course, it only gives
an ordering per class of devices, but in most cases this will be enough,
esp. when platform code uses this. We'll likely need a few extra names
for special cases, but let's use some restraint there, and esp. not
define something as a generic solution when it isn't.
Segher
^ permalink raw reply
* Re: [PATCH v2] Restore deterministic CPU accounting on powerpc
From: Ingo Molnar @ 2007-11-04 9:55 UTC (permalink / raw)
To: Paul Mackerras
Cc: Peter Zijlstra, linuxppc-dev, linux-kernel, Christian Borntraeger,
Martin Schwidefsky, Thomas Gleixner
In-Reply-To: <18220.26005.778223.84644@cargo.ozlabs.ibm.com>
* Paul Mackerras <paulus@samba.org> wrote:
> Signed-off-by: Paul Mackerras <paulus@samba.org>
> ---
> account_process_tick now takes the task_struct * as an argument.
> Tested both with and without CONFIG_VIRT_CPU_ACCOUNTING.
thanks, applied.
Ingo
^ permalink raw reply
* Re: 2.6.24-rc1 freezes on powerbook at first boot stage
From: Elimar Riesebieter @ 2007-11-04 10:38 UTC (permalink / raw)
To: Nathan Lynch; +Cc: linuxppc-dev, Linux Kernel Mailing List
In-Reply-To: <20071104032006.GG9695@localdomain>
On Sat, 03 Nov 2007 the mental interface of
Nathan Lynch told:
> (cc'ing linuxppc-dev, see
> http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg221770.html
> for original post and .config)
[...]
> > console handover: boot [udbg0] -> real [tty0]
>=20
> Does 2.6.23 (or any earlier kernel) work?
The powerbook runs Linux since 2.6.12. The config is generated
always by make oldconfig and checking new options for meaningful
use. If I have time, I test rc versions.
Thanks for cooperation :)
Elimar
--=20
Experience is something you don't get until=20
just after you need it!
^ permalink raw reply
* Re: [PATCH] Restore deterministic CPU accounting on powerpc
From: Michael Neuling @ 2007-11-04 12:11 UTC (permalink / raw)
To: Balbir Singh
Cc: Peter Zijlstra, Christian Borntraeger, linux-kernel, linuxppc-dev,
Paul Mackerras, Martin Schwidefsky, Ingo Molnar, Thomas Gleixner
In-Reply-To: <661de9470711030202x24d0186cuc96a70156ecfa23f@mail.gmail.com>
> > +#ifndef CONFIG_VIRT_CPU_ACCOUNTING
> > +void account_process_tick(int user_tick)
> > +{
> > + if (user_tick) {
> > + account_user_time(p, jiffies_to_cputime(1));
> > + account_user_time_scaled(p, jiffies_to_cputime(1));
> > + } else {
> > + account_system_time(p, HARDIRQ_OFFSET, jiffies_to_cputime(1
));
> > + account_system_time_scaled(p, jiffies_to_cputime(1));
> > + }
> > +}
> > +#endif
> > +
>
> Hi, Paul,
>
> So, scaled accounting will not be available if
> CONFIG_VIRT_CPU_ACCOUNTING is defined? Am I reading this correctly
Balbir,
Paulus' patch will have merge issues with the scaled time cleanup patch
I posted a week or so back. My cleanup patch is only in akpm's tree at
this stage.
Mikey
^ permalink raw reply
* Problem replacing a Samsung K9F1208U0M NAND flash chip with ST NAND512W3A
From: Santanu Sen @ 2007-11-04 14:34 UTC (permalink / raw)
To: linuxppc-embedded
[-- Attachment #1: Type: text/plain, Size: 1607 bytes --]
Facing some trouble replacing a SAMSUNG K9F1208U0M
with an ST NAND512W3A. I know it is criminal, but we
are still using the 2.4 kernel. The excuse is, it is
impossible to port all our code/drivers to 2.6 within
the project deadline.
Here is the story. We could successfully install JFFS2
on a Samsung K9F1208U0M NAND chip mounted on a board
running linux-2.4.20 on a ppc852 processor. But when
we replaced the Samsung chip with an ST NAND512W3A,
creating a JFFS2 partition will no longer work. Raw
read/write to the device is fine. We could even copy a
squashfs image to one of the partitions and mount it
without trouble. But whenever we create a JFFS2
partition, mount it, create a file on it, unmount it
and mount it again the file goes missing. Attaching a
screen-shot of the entire procedure. Note that, the
same steps work fine with Samsung chips. Also, neither
"eraseall" nor "eraseall --jffs2" is of much help in
case of ST. We found some document on the ST site
stating what to do to replace a Samsung chip with an
ST one. The chips are claimed to be equivalent except
that Samsung supports some additional multi-plane
commands. But we could not see those commands being
used anywhere in the mtd code.
Are there anything special to be done for ST NAND
chips?
Any help will be appreciated.
Thanks and Regards,
Santanu
NB: Posting this message here afetr several
unsuccessful attempts to post it on the "jffs2-dev"
mailing list.
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
[-- Attachment #2: 1173074946-st_jffs2_error --]
[-- Type: application/octet-stream, Size: 7705 bytes --]
Tejas U-Boot PrivateBuild:santanu (Oct 10 2007 - 00:35:55)
CPU: XPC852TxxZPnn-VR66 at 50 MHz: 4 kB I-Cache 4 kB D-Cache FEC present
DRAM: (64 MB SDRAM) 64 MB
I2C: ready
Eeprom header mismatch ...
Board: ..? 00:+0x
Ethernet Address: 00:04:95:00:00:01
Date: 0/00/2000 0:00:00
Reserving 4096k for protected RAM at 03c00000
Top of RAM usable for U-Boot at: 03c00000
Reserving 178k for U-Boot at: 03bd3000
Reserving 2064k for malloc() at: 039cf000
Reserving 444 Bytes for Board Info at: 039cee44
Reserving 48 Bytes for Global Data at: 039cedf0
Stack Pointer at: 039cedd8
Eeprom header mismatch ...
New Stack Pointer is: 039cedd8
Now running in RAM - U-Boot at: 03bd3000
FLASH: 2 MB
Using default environment
In: serial
Out: serial
Err: serial
U-Boot relocated to 03bd3000
NAND: Probing at 0xf8000000
Flash chip found:
Manufacturer ID: 0x20, Chip ID: 0x76 (ST Micro 512W3A2BN6)
1 flash chips found. Total nand_chip size: 64 MB
NAND Flash: 64 MB
Net: FEC ETHERNET
Hit'a' to stop, any other key to autoboot: 0
Tejas-pxat-uboot> boot initrd
Loading from device 0: <NULL> at 0xf8000000 (offset 0x0)
Image Name: Linux Multiboot-Image
Image Type: PowerPC Linux Multi-File Image (gzip compressed)
Data Size: 1509590 Bytes = 1.4 MB
Load Address: 00000000
Entry Point: 00000000
Contents:
Image 0: 700108 Bytes = 683.7 kB
Image 1: 809470 Bytes = 790.5 kB
Automatic boot of image at addr 0x00200000 ...
## Booting image at 00200000 ...
Image Name: Linux Multiboot-Image
Image Type: PowerPC Linux Multi-File Image (gzip compressed)
Data Size: 1509590 Bytes = 1.4 MB
Load Address: 00000000
Entry Point: 00000000
Contents:
Image 0: 700108 Bytes = 683.7 kB
Image 1: 809470 Bytes = 790.5 kB
Verifying Checksum ... OK
Uncompressing Multi-File Image ... OK
Loading Ramdisk to 03908000, end 039cd9fe ... OK
Linux version 2.4.20-denx-PrivateBuild:santanu (santanu@sephia) (gcc version 2.95.4 20010319 (prerelease/franzo/20011204)) #2 Tue Oct 9 20:50:51 IST 2007
On node 0 totalpages: 15359
zone(0): 15359 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: slram=mtd_tjram01,0x3C00000,+0x400000 console=ttyS0,57600 init=/etc/rc.sh root=/dev/ram rw mtdsize0=0x00040000 mtdparts=a initrd
Decrementer Frequency = 187500000/60
Warning: real time clock seems stuck!
Calibrating delay loop... 49.66 BogoMIPS
Memory: 57584k available (1332k kernel code, 432k data, 56k init, 0k highmem)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
POSIX conformance testing by UNIFIX
WDT_8xx: SWT not enabled by firmware, SYPCR=0xffffff89
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications AB.
squashfs: version 3.1 (2006/08/19) Phillip Lougher
CPM UART driver version 0.04
ttyS0 on SMC1 at 0x0280, BRG1
pty: 256 Unix98 ptys configured
eth0: FEC ENET Version 0.3, FEC irq 11, with MDIO, addr 00:04:95:00:00:01
eth0: Phy @ 0x0, type RTL8201 (0x00008201)
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
tn100map flash device: 00200000 at 40000000
Amd/Fujitsu Extended Query Table v1.0 at 0x0040
Physically mapped flash: JEDEC Device ID is 0xC4. Assuming broken CFI table.
Physically mapped flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Using tn100_map partition definition
Creating 1 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "uboot"
NAND device: Manufacture ID: 0x20, Chip ID: 0x76 (ST Micro NAND 64MiB 3,3V)
Creating 10 MTD partitions on "NAND 64MiB 3,3V":
0x00000000-0x00200000 : "linux_initrd"
0x00200000-0x00600000 : "rootfs"
0x00600000-0x00a00000 : "backroot"
0x00a00000-0x01e00000 : "software"
0x01e00000-0x03200000 : "backsoft"
0x03200000-0x03600000 : "tejas"
0x03600000-0x03e00000 : "log"
0x03e00000-0x03f00000 : "diag"
0x03f00000-0x03f40000 : "mapper"
0x03f40000-0x03fc0000 : "tomfpga"
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 4096)
IPv4 over IPv4 tunneling driver
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.1 (479 buckets, 3832 max) - 292 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
arp_tables: (C) 2002 David S. Miller
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 790k freed
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 56k init
/bin/mount -t proc proc /proc
mount -t ramfs none /var && mkdir /var/cron /var/lock /var/lock/subsys /var/log /var/run /var/tmp /var/dumps && touch /var/log/wtmp /var/run/utmp
cp -a /dev/* /tmp && mount -t ramfs none /dev && mv /tmp/* /dev
eth0: config: auto-negotiation on, 100HDX, 10HDX.
slram=mtd_tjram01,0x3C00000,+0x400000 console=ttyS0,57600 init=/etc/rc.sh root=/dev/ram rw mtdsize0=0x00040000 mtdparts=a initrd
init started: BusyBox v0.60.5 (2006.05.15-11:55+0000) multi-call
BusyBox v0.60.5 (2006.06.02-06:31+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
source: not found
(none)> eth0: status: link up, 100 Mbps Half Duplex, auto-negotiation complete.
(none)>
(none)> eraseall /dev/mtd8
Erasing 16 Kibyte @ 7fc000 -- 99 % complete.
(none)> mount -t jffs2 /dev/mtdblock8 /tmp/drive1
(none)> cd /tmp/drive1
(none)> echo "aa" > txt
(none)> cat txt
aa
(none)> sync
(none)> cd ..
(none)> umount drive1
(none)> mount -t jffs2 /dev/mtdblock8 drive1
Node header CRC failed at 007f8244. But it must have been OK earlier.
Node was: { ffff, ffff, ffffffff, ffffffff }
Eep. Unknown node type ffff at 007f8270 was marked REF_UNCHECKED
Node header CRC failed at 007f8270. But it must have been OK earlier.
Node was: { ffff, ffff, ffffffff, ffffffff }
(none)> Eep. Unknown node type ffff at 007f8200 was marked REF_UNCHECKED
Node header CRC failed at 007f8200. But it must have been OK earlier.
Node was: { ffff, ffff, ffffffff, ffffffff }
(none)> cd drive1
(none)> ls
(none)>
^ permalink raw reply
* mpc852t boot question!
From: Kugel @ 2007-11-04 16:18 UTC (permalink / raw)
To: linuxppc-dev
[-- Attachment #1: Type: text/plain, Size: 277 bytes --]
I made a MPC852T board. I set the HW config word to 0x04600000(D5,D9,D10
pulled up).So the [ISB]=00,
and the IMMR = 0x00000000.
When the CPU is power up, can it boot from external boot flash(39vf040)? Or
just run from internal
memory space(because the IMMR=0x0)?
[-- Attachment #2: Type: text/html, Size: 1306 bytes --]
^ permalink raw reply
* [PATCH] Balance alloc/free and ioremap/iounmap in gpio_mdio_probe (powerpc/platforms/pasemi/gpio_mdio.c)
From: Roel Kluin @ 2007-11-04 16:53 UTC (permalink / raw)
To: linuxppc-dev
I think this is how it should be done, but
please review: it was not tested.
--
Balance alloc/free and ioremap/iounmap
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
---
diff --git a/arch/powerpc/platforms/pasemi/gpio_mdio.c b/arch/powerpc/platforms/pasemi/gpio_mdio.c
index dae9f65..f250ba4 100644
--- a/arch/powerpc/platforms/pasemi/gpio_mdio.c
+++ b/arch/powerpc/platforms/pasemi/gpio_mdio.c
@@ -208,95 +208,116 @@ static int gpio_mdio_write(struct mii_bus *bus, int phy_id, int location, u16 va
}
static int gpio_mdio_reset(struct mii_bus *bus)
{
/*nothing here - dunno how to reset it*/
return 0;
}
-
-static int __devinit gpio_mdio_probe(struct of_device *ofdev,
- const struct of_device_id *match)
+static int __devinit __gpio_mdio_register_bus(struct of_device *ofdev,
+ const struct of_device_id *match)
{
struct device *dev = &ofdev->dev;
struct device_node *np = ofdev->node;
- struct device_node *gpio_np;
struct mii_bus *new_bus;
struct resource res;
struct gpio_priv *priv;
const unsigned int *prop;
- int err = 0;
int i;
- gpio_np = of_find_compatible_node(NULL, "gpio", "1682m-gpio");
-
- if (!gpio_np)
- return -ENODEV;
-
- err = of_address_to_resource(gpio_np, 0, &res);
- of_node_put(gpio_np);
-
- if (err)
- return -EINVAL;
-
- if (!gpio_regs)
- gpio_regs = ioremap(res.start, 0x100);
-
- if (!gpio_regs)
- return -EPERM;
-
priv = kzalloc(sizeof(struct gpio_priv), GFP_KERNEL);
- if (priv == NULL)
+ if (unlikely(priv == NULL))
return -ENOMEM;
new_bus = kzalloc(sizeof(struct mii_bus), GFP_KERNEL);
- if (new_bus == NULL)
- return -ENOMEM;
+ if (unlikely(new_bus == NULL))
+ goto free_priv;
new_bus->name = "pasemi gpio mdio bus",
new_bus->read = &gpio_mdio_read,
new_bus->write = &gpio_mdio_write,
new_bus->reset = &gpio_mdio_reset,
prop = of_get_property(np, "reg", NULL);
new_bus->id = *prop;
new_bus->priv = priv;
new_bus->phy_mask = 0;
new_bus->irq = kmalloc(sizeof(int)*PHY_MAX_ADDR, GFP_KERNEL);
+ if (unlikely(new_bus->irq == NULL))
+ goto free_new_bus;
+
for(i = 0; i < PHY_MAX_ADDR; ++i)
new_bus->irq[i] = irq_create_mapping(NULL, 10);
prop = of_get_property(np, "mdc-pin", NULL);
priv->mdc_pin = *prop;
prop = of_get_property(np, "mdio-pin", NULL);
priv->mdio_pin = *prop;
new_bus->dev = dev;
dev_set_drvdata(dev, new_bus);
err = mdiobus_register(new_bus);
- if (0 != err) {
+ if (unlikely(0 != err)) {
printk(KERN_ERR "%s: Cannot register as MDIO bus, err %d\n",
new_bus->name, err);
goto bus_register_fail;
}
return 0;
bus_register_fail:
+ kfree(new_bus->irq);
+free_new_bus:
kfree(new_bus);
+free_priv:
+ kfree(priv);
+
+ return -ENOMEM;
+}
+
+
+static int __devinit gpio_mdio_probe(struct of_device *ofdev,
+ const struct of_device_id *match)
+{
+ struct device_node *gpio_np;
+ int err;
+
+ gpio_np = of_find_compatible_node(NULL, "gpio", "1682m-gpio");
+
+ if (!gpio_np)
+ return -ENODEV;
+
+ err = of_address_to_resource(gpio_np, 0, &res);
+ of_node_put(gpio_np);
+
+ if (err)
+ return -EINVAL;
+
+ if (!gpio_regs) {
+
+ gpio_regs = ioremap(res.start, 0x100);
+ if (unlikely(!gpio_regs))
+ return -EPERM;
+
+ err = __gpio_mdio_register_bus(ofdev, match);
+ if (err < 0)
+ iounmap(gpio_regs);
+ } else
+ err = __gpio_mdio_register_bus(ofdev, match);
return err;
+
}
static int gpio_mdio_remove(struct of_device *dev)
{
struct mii_bus *bus = dev_get_drvdata(&dev->dev);
mdiobus_unregister(bus);
^ permalink raw reply related
* Re: [PATCH] net: Add 405EX support to new EMAC driver
From: Olof Johansson @ 2007-11-04 17:16 UTC (permalink / raw)
To: Benjamin Herrenschmidt; +Cc: netdev, Stefan Roese, linuxppc-dev
In-Reply-To: <1194147479.6511.11.camel@pasglop>
On Sun, Nov 04, 2007 at 02:37:59PM +1100, Benjamin Herrenschmidt wrote:
>
> On Fri, 2007-11-02 at 11:03 -0500, Olof Johansson wrote:
> > On Fri, Nov 02, 2007 at 08:14:43AM +0100, Stefan Roese wrote:
> > > This patch adds support for the 405EX to the new EMAC driver. Some as on
> > > AXON, the 405EX handles the MDIO via the RGMII bridge.
> >
> > Hi,
> >
> > This isn't feedback on your patch as much as on "new-emac" in general:
> >
> > Isn't this the case where there should really be device tree properties
> > instead? If you had an "ibm,emac-has-axon-stacr" property in the device
> > node, then you don't have to modify the driver for every new board out
> > there. Same for the other device properties, of course.
> >
> > I thought this was what having the device tree was all about. :(
>
> Somewhat yeah. There are subtle variations here or there we haven't
> totally indenfified... It might be a better option in our case here to
> add "has-mdio" to the rgmii nodes indeed.
>
> Part of the problem with those cells is that the chip folks keep
> changing things subtly from one rev to another though, it's not even
> totally clear to me yet whether the RGMII registers are totally
> compatible betwee axon and 405ex, which is why I've pretty much stuck to
> "compatible" properties to identify the variants.
>
> The device-tree can do both. It's still better than no device-tree since
> at least you know what cell variant is in there.
Well, it's better than compile-time ifdefs. Providing what version of
the device you have CAN be done without a device tree too. :-)
> As for the STACR, Axon isn't the first one to have that bit flipped, I
> think we should name the property differently, something like
> "stacr-oc-inverted".
Sure, it was the habit of having to modify the driver for platforms that
don't add any new features I was against. I don't really care what the
properties are called :-)
> We can still use properties that way for new things in fact. As for EMAC
> on cell, well, I can always put some fixup somewhere.
Sounds good (with s/can still/should/).
-Olof
^ permalink raw reply
* Re: [PATCH] Balance alloc/free and ioremap/iounmap in gpio_mdio_probe (powerpc/platforms/pasemi/gpio_mdio.c)
From: Nathan Lynch @ 2007-11-04 17:18 UTC (permalink / raw)
To: Roel Kluin; +Cc: linuxppc-dev
In-Reply-To: <472DF914.7020601@tiscali.nl>
Hi,
Roel Kluin wrote:
> I think this is how it should be done, but
> please review: it was not tested.
> --
> Balance alloc/free and ioremap/iounmap
It would be more helpful if your changelog identified the objects
which could be leaked. More comments below.
> -static int __devinit gpio_mdio_probe(struct of_device *ofdev,
> - const struct of_device_id *match)
> +static int __devinit __gpio_mdio_register_bus(struct of_device *ofdev,
> + const struct of_device_id *match)
> {
> struct device *dev = &ofdev->dev;
> struct device_node *np = ofdev->node;
> - struct device_node *gpio_np;
> struct mii_bus *new_bus;
> struct resource res;
> struct gpio_priv *priv;
> const unsigned int *prop;
> - int err = 0;
> int i;
>
> - gpio_np = of_find_compatible_node(NULL, "gpio", "1682m-gpio");
> -
> - if (!gpio_np)
> - return -ENODEV;
> -
> - err = of_address_to_resource(gpio_np, 0, &res);
> - of_node_put(gpio_np);
> -
> - if (err)
> - return -EINVAL;
> -
> - if (!gpio_regs)
> - gpio_regs = ioremap(res.start, 0x100);
> -
> - if (!gpio_regs)
> - return -EPERM;
> -
> priv = kzalloc(sizeof(struct gpio_priv), GFP_KERNEL);
> - if (priv == NULL)
> + if (unlikely(priv == NULL))
> return -ENOMEM;
Please don't add likely/unlikely to non-hot paths such as this.
> new_bus = kzalloc(sizeof(struct mii_bus), GFP_KERNEL);
>
> - if (new_bus == NULL)
> - return -ENOMEM;
> + if (unlikely(new_bus == NULL))
> + goto free_priv;
again
>
> new_bus->name = "pasemi gpio mdio bus",
> new_bus->read = &gpio_mdio_read,
> new_bus->write = &gpio_mdio_write,
> new_bus->reset = &gpio_mdio_reset,
>
> prop = of_get_property(np, "reg", NULL);
> new_bus->id = *prop;
> new_bus->priv = priv;
>
> new_bus->phy_mask = 0;
>
> new_bus->irq = kmalloc(sizeof(int)*PHY_MAX_ADDR, GFP_KERNEL);
> + if (unlikely(new_bus->irq == NULL))
> + goto free_new_bus;
> +
again
> for(i = 0; i < PHY_MAX_ADDR; ++i)
> new_bus->irq[i] = irq_create_mapping(NULL, 10);
>
>
> prop = of_get_property(np, "mdc-pin", NULL);
> priv->mdc_pin = *prop;
>
> prop = of_get_property(np, "mdio-pin", NULL);
> priv->mdio_pin = *prop;
>
> new_bus->dev = dev;
> dev_set_drvdata(dev, new_bus);
>
> err = mdiobus_register(new_bus);
>
> - if (0 != err) {
> + if (unlikely(0 != err)) {
again
> printk(KERN_ERR "%s: Cannot register as MDIO bus, err %d\n",
> new_bus->name, err);
> goto bus_register_fail;
> }
>
> return 0;
>
> bus_register_fail:
> + kfree(new_bus->irq);
> +free_new_bus:
> kfree(new_bus);
> +free_priv:
> + kfree(priv);
> +
> + return -ENOMEM;
> +}
> +
> +
> +static int __devinit gpio_mdio_probe(struct of_device *ofdev,
> + const struct of_device_id *match)
> +{
> + struct device_node *gpio_np;
> + int err;
> +
> + gpio_np = of_find_compatible_node(NULL, "gpio", "1682m-gpio");
> +
> + if (!gpio_np)
> + return -ENODEV;
> +
> + err = of_address_to_resource(gpio_np, 0, &res);
Hmm, where is "res" defined?
> + of_node_put(gpio_np);
> +
> + if (err)
> + return -EINVAL;
> +
> + if (!gpio_regs) {
> +
Unneeded newline
> + gpio_regs = ioremap(res.start, 0x100);
> + if (unlikely(!gpio_regs))
> + return -EPERM;
> +
> + err = __gpio_mdio_register_bus(ofdev, match);
> + if (err < 0)
> + iounmap(gpio_regs);
> + } else
> + err = __gpio_mdio_register_bus(ofdev, match);
>
> return err;
> +
again
> }
>
>
> static int gpio_mdio_remove(struct of_device *dev)
> {
> struct mii_bus *bus = dev_get_drvdata(&dev->dev);
>
> mdiobus_unregister(bus);
>
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox