* [PATCH 3/3] Modified Documentation to explain dts entries for UCC TDM driver.
From: Poonam_Aggrwal-b10812 @ 2007-12-10 12:13 UTC (permalink / raw)
To: rubini, kumar.gala, linux-kernel, netdev, linuxppc-dev
Cc: michael.barkowski, rich.cutler, ashish.kalra
From: Poonam Aggrwal <b10812@freescale.com>
Modified Documentation to explain new properties introduced for UCC TDM
driver. Also two new nodes have been added "brg" and "clocks" to configure
a BRG from device tree.
Signed-off-by: Poonam Aggrwal <b10812@freescale.com>
Signed-off-by: Ashish Kalra <ashish.kalra@freescale.com>
Signed-off-by: Kim Phillips <Kim.Phillips@freescale.com>
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
---
Documentation/powerpc/booting-without-of.txt | 96 +++++++++++++++++++++++++-
1 files changed, 94 insertions(+), 2 deletions(-)
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index e9a3cb1..94a6b4b 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -1613,8 +1613,8 @@ platforms are moved over to use the flattened-device-tree model.
Required properties:
- device_type : should be "network", "hldc", "uart", "transparent"
- "bisync" or "atm".
- - compatible : could be "ucc_geth" or "fsl_atm" and so on.
+ "bisync", "atm" or "tdm".
+ - compatible : could be "ucc_geth", "fsl_atm" or "fsl,ucc_tdm" and so on.
- model : should be "UCC".
- device-id : the ucc number(1-8), corresponding to UCCx in UM.
- reg : Offset and length of the register set for the device
@@ -1666,7 +1666,44 @@ platforms are moved over to use the flattened-device-tree model.
pio-handle = <140001>;
};
+ Required properties for tdm device_type:
+ - instead of tx-clock and rx-clock following clock properties are
+ required:
+ - fsl,tdm-tx-clk : This property selects the TX clock source for TDM
+ from a bank of clocks.
+ - fsl,tdm-rx-clk : This property selects the RX clock source for TDM
+ from a bank of clocks.
+ - fsl,tdm-tx-sync : This property selects the TX Frame sync source
+ for TDM from a bank of clocks.
+ - fsl,tdm-rx-sync : This property selects the TX Frame sync source
+ for TDM from a bank of clocks.
+
+ All the above mentioned properties are string type with possible
+ values
+ "CLK1", "CLK2", "CLK3"..."CLK24" and so on
+ "BRG1", "BRG2", "BRG3"..."BRG16" and so on
+
+ - fsl,tdm-num : TDM to be used (1,2,3 or 4 for TDMA TDMB TDMC TDMD)
+ - fsl,si-num : Serial Interface to be used.
+ Example:
+ ucc@2000 {
+ device_type = "tdm";
+ compatible = "fsl,ucc-tdm";
+ model = "UCC";
+ device-id = <1>;
+ fsl,tdm-num = <1>;
+ fsl,si-num = <1>;
+ fsl,tdm-tx-clk = "CLK1";
+ fsl,tdm-rx-clk = "CLK1";
+ fsl,tdm-tx-sync = "BRG9";
+ fsl,tdm-rx-sync = "BRG9";
+ reg = <2000 200>;
+ interrupts = <20>;
+ interrupt-parent = <&qeic>;
+ pio-handle = <&ucc1pio>;
+ };
+
v) Parallel I/O Ports
This node configures Parallel I/O ports for CPUs with QE support.
@@ -1772,6 +1809,61 @@ platforms are moved over to use the flattened-device-tree model.
};
};
+ viii) Clocks (clocks)
+ This node specifies the frequency values for all the external clocks
+ viz CLK1 to CLK24 in Hz.
+
+ Required Properties:
+ - compatible : should be "fsl,cpm-clocks".
+ - #clock-cells : It specifies the number of cells occupied by clock-frequency
+ property. Currently #clock-cells = 1 is only supported and implemented.
+ This property is kept for future in case we need frequencies higher than
+ 4 GHz.
+ - clock-frequency : It is a list of u32 values to represent the frequency
+ of each external clock(CLK1 to CLK24) in Hz.Each entry occupies
+ number of cells specified by #clock-cells property(1 for now).
+
+ Example:
+
+ clocks {
+ compatible = "fsl,cpm-clocks";
+ #clock-cells = <1>;
+ /* clock freqs in Hz(for CLK1~CLK24).
+ * CLK11 is 1024KHz,
+ * all other clocks unused
+ */
+ clock-frequency = <0 0 0 0 0 0
+ 0 0 0 0 0 d#1024000 0
+ 0 0 0 0 0 0
+ 0 0 0 0 0 0>;
+ };
+
+ ix) Baud Rate Generator (BRG)
+
+ Required properties:
+ - compatible : shpuld be "fsl,cpm-brg"
+ - fsl,brg-sources : define the input clock for all 16 BRGs. The input
+ clock source could be 1 to 24 for CLK1 to CLK24. Zero means that the
+ particular BRG will be driven by QE clock(BRGCLK).
+ - reg : This property defines the address and size of the memory-mapped
+ registers of the BRG.
+
+ Example:
+
+ brg@640 {
+ compatible = "fsl,qe-brg";
+ /* input clock sources for all the 16 BRGs.
+ * 1-24 for CLK1 to CLK24.
+ * BRG9 uses CLK11 others use
+ * the QE clock.
+ */
+ fsl,brg-sources = <0 0 0 0 0 0 0 0
+ b 0 0 0 0 0 0 0>;
+ reg = <640 7f>;
+ };
+
+ In the above entry, for BRG9 the input clock is 0xb(decimal 11) ie QE_CLK11.
+
j) CFI or JEDEC memory-mapped NOR flash
Flash chips (Memory Technology Devices) are often used for solid state
--
1.5.2.4
^ permalink raw reply related
* Re: [PATCH] Fix rounding bug in emulation for double floatoperating
From: Kumar Gala @ 2007-12-10 15:00 UTC (permalink / raw)
To: Liu Yu; +Cc: linuxppc-dev, David Gibson
In-Reply-To: <6EBEC19BF4A8F843BCD6B9155BBE2515C79D0D@zch01exm26.fsl.freescale.net>
On Dec 9, 2007, at 11:25 PM, Liu Yu wrote:
>
>
>
>
>
>> -----Original Message-----
>> From: David Gibson [mailto:david@gibson.dropbear.id.au]
>> Sent: Monday, December 10, 2007 12:56 PM
>> To: Liu Yu
>> Cc: linuxppc-dev@ozlabs.org
>> Subject: Re: [PATCH] Fix rounding bug in emulation for double
>> floatoperating
>>
>>
>> On Mon, Dec 10, 2007 at 01:00:52PM +0800, Liu Yu wrote:
>>>
>>> This patch fixes rounding bug in emulation for double float
>> operating on PowerPC platform.
>>>
>>> When pack double float operand, it need to truncate the
>> tail due to the limited precision.
>>> If the truncated part is not zero, the last bit of work bit
>> (totally 3 bits) need to '|' 1.
>>>
>>> This patch is completed in _FP_FRAC_SRS_2(X,N,sz)
>> (arch/powerpc/math-emu/op-2.h).
>>> Originally the code leftwards rotates the operand to just keep the
>>> truncated part, then check whether it is zero. However, the
>> number it
>>> rotates is not correct when N is not smaller than
>> _FP_W_TYPE_SIZE, and it will cause the work bit '|' 1 in the
>> improper case.
>>>
>>> This patch fixes this issue.
>>>
>>> Signed-off-by: Liu Yu <b13201@freescale.com>
>>
>> Wow someone deciphered the hideous macro hell of the math
>> emulation code enough to fix a bug. I don't suppose you'd
>> care to fix the millions of warnings that the math-emu code
>> generates...?
>
> Oh, I don't like macro define either. But it's really a bug...
how did you find this?
- k
^ permalink raw reply
* Re: [PATCH] windfarm: add PowerMac 12,1 support
From: Étienne Bersac @ 2007-12-10 15:11 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1196955051.6862.10.camel@thilivren>
From: Étienne Bersac <bersace03@gmail.com>
Hi,
Here is an updated patch that fix the potential bug, CPU param detection
failure might not be detected. Please review it.
Regards,
Étienne.
Signed-off-by: Étienne Bersac <bersace03@gmail.com>
---
Implement fan control for PowerMac 12,1 machines. This needs update to
windfarm_lm75 and windfarm_max6690 sensors drivers in order to properly
match sensors by their location. The code is based on windfarm_pm81
driver, adapted to the complexity of PowerMac 12,1 : 4 system control
loops instead of one, per-control target correction and per-model
control rubber-banding.
All the data are copied from Darwin 8.10 AppleMacRISC4PE-185.0.0 module
as well as correction formula.
diff --git a/arch/powerpc/configs/g5_defconfig b/arch/powerpc/configs/g5_defconfig
index 0a6fa1f..7125837 100644
--- a/arch/powerpc/configs/g5_defconfig
+++ b/arch/powerpc/configs/g5_defconfig
@@ -656,6 +656,7 @@ CONFIG_WINDFARM=y
CONFIG_WINDFARM_PM81=y
CONFIG_WINDFARM_PM91=y
CONFIG_WINDFARM_PM112=y
+CONFIG_WINDFARM_PM121=y
# CONFIG_PMAC_RACKMETER is not set
CONFIG_NETDEVICES=y
# CONFIG_NETDEVICES_MULTIQUEUE is not set
diff --git a/drivers/macintosh/Kconfig b/drivers/macintosh/Kconfig
index 77f50b6..2d028e6 100644
--- a/drivers/macintosh/Kconfig
+++ b/drivers/macintosh/Kconfig
@@ -234,6 +234,14 @@ config WINDFARM_PM112
which are the recent dual and quad G5 machines using the
970MP dual-core processor.
+config WINDFARM_PM121
+ tristate "Support for thermal management on PowerMac12,1"
+ depends on WINDFARM && I2C && PMAC_SMU
+ select I2C_POWERMAC
+ help
+ This driver provides thermal control for the PowerMac12,1
+ which is the iMac G5 (iSight) 970MP
+
config ANSLCD
tristate "Support for ANS LCD display"
depends on ADB_CUDA && PPC_PMAC
diff --git a/drivers/macintosh/Makefile b/drivers/macintosh/Makefile
index 2dfc3f4..e3132ef 100644
--- a/drivers/macintosh/Makefile
+++ b/drivers/macintosh/Makefile
@@ -42,4 +42,9 @@ obj-$(CONFIG_WINDFARM_PM112) += windfarm_pm112.o windfarm_smu_sat.o \
windfarm_smu_sensors.o \
windfarm_max6690_sensor.o \
windfarm_lm75_sensor.o windfarm_pid.o
+obj-$(CONFIG_WINDFARM_PM121) += windfarm_pm121.o windfarm_smu_sat.o \
+ windfarm_smu_controls.o \
+ windfarm_smu_sensors.o \
+ windfarm_max6690_sensor.o \
+ windfarm_lm75_sensor.o windfarm_pid.o
obj-$(CONFIG_PMAC_RACKMETER) += rack-meter.o
diff --git a/drivers/macintosh/windfarm_lm75_sensor.c b/drivers/macintosh/windfarm_lm75_sensor.c
index 7e10c3a..b92b959 100644
--- a/drivers/macintosh/windfarm_lm75_sensor.c
+++ b/drivers/macintosh/windfarm_lm75_sensor.c
@@ -127,6 +127,12 @@ static struct wf_lm75_sensor *wf_lm75_create(struct i2c_adapter *adapter,
*/
if (!strcmp(loc, "Hard drive") || !strcmp(loc, "DRIVE BAY"))
lm->sens.name = "hd-temp";
+ else if (!strcmp(loc, "Incoming Air Temp"))
+ lm->sens.name = "incoming-air-temp";
+ else if (!strcmp(loc, "ODD Temp"))
+ lm->sens.name = "optical-drive-temp";
+ else if (!strcmp(loc, "HD Temp"))
+ lm->sens.name = "hard-drive-temp";
else
goto fail;
diff --git a/drivers/macintosh/windfarm_max6690_sensor.c b/drivers/macintosh/windfarm_max6690_sensor.c
index 5f03aab..c2b6d1c 100644
--- a/drivers/macintosh/windfarm_max6690_sensor.c
+++ b/drivers/macintosh/windfarm_max6690_sensor.c
@@ -77,10 +77,11 @@ static struct wf_sensor_ops wf_max6690_ops = {
.owner = THIS_MODULE,
};
-static void wf_max6690_create(struct i2c_adapter *adapter, u8 addr)
+static void wf_max6690_create(struct i2c_adapter *adapter, u8 addr,
+ const char *loc)
{
struct wf_6690_sensor *max;
- char *name = "backside-temp";
+ char *name = NULL;
max = kzalloc(sizeof(struct wf_6690_sensor), GFP_KERNEL);
if (max == NULL) {
@@ -89,6 +90,15 @@ static void wf_max6690_create(struct i2c_adapter *adapter, u8 addr)
return;
}
+ if (!strcmp(loc, "BACKSIDE"))
+ name = "backside-temp";
+ else if (!strcmp(loc, "NB Ambient"))
+ name = "north-bridge-temp";
+ else if (!strcmp(loc, "GPU Ambient"))
+ name = "gpu-temp";
+ else
+ goto fail;
+
max->sens.ops = &wf_max6690_ops;
max->sens.name = name;
max->i2c.addr = addr >> 1;
@@ -138,9 +148,7 @@ static int wf_max6690_attach(struct i2c_adapter *adapter)
if (loc == NULL || addr == 0)
continue;
printk("found max6690, loc=%s addr=0x%02x\n", loc, addr);
- if (strcmp(loc, "BACKSIDE"))
- continue;
- wf_max6690_create(adapter, addr);
+ wf_max6690_create(adapter, addr, loc);
}
return 0;
diff --git a/drivers/macintosh/windfarm_pm121.c b/drivers/macintosh/windfarm_pm121.c
new file mode 100644
index 0000000..e3a9c50
--- /dev/null
+++ b/drivers/macintosh/windfarm_pm121.c
@@ -0,0 +1,1053 @@
+/*
+ * Windfarm PowerMac thermal control. iMac G5 iSight
+ *
+ * (c) Copyright 2007 Étienne Bersac <bersace@gmail.com>
+ *
+ * Bits & pieces from windfarm_pm81.c by (c) Copyright 2005 Benjamin
+ * Herrenschmidt, IBM Corp. <benh@kernel.crashing.org>
+ *
+ * Released under the term of the GNU GPL v2.
+ *
+ *
+ *
+ * PowerMac12,1
+ * ============
+ *
+ *
+ * The algorithm used is the PID control algorithm, used the same way
+ * the published Darwin code does, using the same values that are
+ * present in the Darwin 8.10 snapshot property lists (note however
+ * that none of the code has been re-used, it's a complete
+ * re-implementation
+ *
+ * There is two models using PowerMac12,1. Model 2 is iMac G5 iSight
+ * 17" while Model 3 is iMac G5 20". They do have both the same
+ * controls with a tiny difference. The control-ids of hard-drive-fan
+ * and cpu-fan is swapped.
+ *
+ *
+ * Target Correction :
+ *
+ * controls have a target correction calculated as :
+ *
+ * new_min = ((((average_power * slope) >> 16) + offset) >> 16) + min_value
+ * new_value = max(new_value, max(new_min, 0))
+ *
+ * OD Fan control correction.
+ *
+ * # model_id: 2
+ * offset : -19563152
+ * slope : 1956315
+ *
+ * # model_id: 3
+ * offset : -15650652
+ * slope : 1565065
+ *
+ * HD Fan control correction.
+ *
+ * # model_id: 2
+ * offset : -15650652
+ * slope : 1565065
+ *
+ * # model_id: 3
+ * offset : -19563152
+ * slope : 1956315
+ *
+ * CPU Fan control correction.
+ *
+ * # model_id: 2
+ * offset : -25431900
+ * slope : 2543190
+ *
+ * # model_id: 3
+ * offset : -15650652
+ * slope : 1565065
+ *
+ *
+ * Target rubber-banding :
+ *
+ * Some controls have a target correction which depends on another
+ * control value. The correction is computed in the following way :
+ *
+ * new_min = ref_value * slope + offset
+ *
+ * ref_value is the value of the reference control. If new_min is
+ * greater than 0, then we correct the target value using :
+ *
+ * new_target = max (new_target, new_min >> 16)
+ *
+ *
+ * # model_id : 2
+ * control : cpu-fan
+ * ref : optical-drive-fan
+ * offset : -15650652
+ * slope : 1565065
+ *
+ * # model_id : 3
+ * control : optical-drive-fan
+ * ref : hard-drive-fan
+ * offset : -32768000
+ * slope : 65536
+ *
+ *
+ * In order to have the moste efficient correction with those
+ * dependencies, we must trigger HD loop before OD loop before CPU
+ * loop.
+ *
+ *
+ * The various control loops found in Darwin config file are:
+ *
+ * HD Fan control loop.
+ *
+ * # model_id: 2
+ * control : hard-drive-fan
+ * sensor : hard-drive-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x002D70A3
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x370000
+ * Interval = 5s
+ *
+ * # model_id: 3
+ * control : hard-drive-fan
+ * sensor : hard-drive-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x002170A3
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x370000
+ * Interval = 5s
+ *
+ * OD Fan control loop.
+ *
+ * # model_id: 2
+ * control : optical-drive-fan
+ * sensor : optical-drive-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x001FAE14
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x320000
+ * Interval = 5s
+ *
+ * # model_id: 3
+ * control : optical-drive-fan
+ * sensor : optical-drive-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x001FAE14
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x320000
+ * Interval = 5s
+ *
+ * GPU Fan control loop.
+ *
+ * # model_id: 2
+ * control : hard-drive-fan
+ * sensor : gpu-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x002A6666
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x5A0000
+ * Interval = 5s
+ *
+ * # model_id: 3
+ * control : cpu-fan
+ * sensor : gpu-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x0010CCCC
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x500000
+ * Interval = 5s
+ *
+ * KODIAK (aka northbridge) Fan control loop.
+ *
+ * # model_id: 2
+ * control : optical-drive-fan
+ * sensor : north-bridge-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x003BD70A
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x550000
+ * Interval = 5s
+ *
+ * # model_id: 3
+ * control : hard-drive-fan
+ * sensor : north-bridge-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x0030F5C2
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x550000
+ * Interval = 5s
+ *
+ * CPU Fan control loop.
+ *
+ * control : cpu-fan
+ * sensors : cpu-temp, cpu-power
+ * PID params : from SDB partition
+ *
+ *
+ * CPU Slew control loop.
+ *
+ * control : cpufreq-clamp
+ * sensor : cpu-temp
+ *
+ */
+
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/init.h>
+#include <linux/spinlock.h>
+#include <linux/wait.h>
+#include <linux/kmod.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <asm/prom.h>
+#include <asm/machdep.h>
+#include <asm/io.h>
+#include <asm/system.h>
+#include <asm/sections.h>
+#include <asm/smu.h>
+
+#include "windfarm.h"
+#include "windfarm_pid.h"
+
+#define VERSION "0.4"
+
+#undef DEBUG
+
+#ifdef DEBUG
+#define DBG(args...) printk(args)
+#else
+#define DBG(args...) do { } while (0)
+#endif
+
+static int pm121_mach_model; /* machine model id */
+
+/* Controls & sensors */
+static struct wf_sensor *sensor_cpu_power;
+static struct wf_sensor *sensor_cpu_temp;
+static struct wf_sensor *sensor_cpu_voltage;
+static struct wf_sensor *sensor_cpu_current;
+static struct wf_sensor *sensor_gpu_temp;
+static struct wf_sensor *sensor_north_bridge_temp;
+static struct wf_sensor *sensor_hard_drive_temp;
+static struct wf_sensor *sensor_optical_drive_temp;
+static struct wf_sensor *sensor_incoming_air_temp; /* unused ! */
+
+enum {
+ FAN_CPU,
+ FAN_HD,
+ FAN_OD,
+ CPUFREQ,
+ N_CONTROLS
+};
+static struct wf_control *controls[N_CONTROLS] = {};
+
+/* Set to kick the control loop into life */
+static int pm121_all_controls_ok, pm121_all_sensors_ok, pm121_started;
+
+enum {
+ FAILURE_FAN = 1 << 0,
+ FAILURE_SENSOR = 1 << 1,
+ FAILURE_OVERTEMP = 1 << 2
+};
+
+/* All sys loops. Note the HD before the OD loop in order to have it
+ run before. */
+enum {
+ LOOP_GPU, /* control = hd or cpu, but luckily,
+ it doesn't matter */
+ LOOP_HD, /* control = hd */
+ LOOP_KODIAK, /* control = hd or od */
+ LOOP_OD, /* control = od */
+ N_LOOPS
+};
+
+static const char *loop_names[N_LOOPS] = {
+ "GPU",
+ "HD",
+ "KODIAK",
+ "OD",
+};
+
+#define PM121_NUM_CONFIGS 2
+
+static unsigned int pm121_failure_state;
+static int pm121_readjust, pm121_skipping;
+static s32 average_power;
+
+struct pm121_correction {
+ int offset;
+ int slope;
+};
+
+struct pm121_correction corrections[N_CONTROLS][PM121_NUM_CONFIGS] = {
+ /* FAN_OD */
+ {
+ /* MODEL 2 */
+ { .offset = -19563152,
+ .slope = 1956315
+ },
+ /* MODEL 3 */
+ { .offset = -15650652,
+ .slope = 1565065
+ },
+ },
+ /* FAN_HD */
+ {
+ /* MODEL 2 */
+ { .offset = -15650652,
+ .slope = 1565065
+ },
+ /* MODEL 3 */
+ { .offset = -19563152,
+ .slope = 1956315
+ },
+ },
+ /* FAN_CPU */
+ {
+ /* MODEL 2 */
+ { .offset = -25431900,
+ .slope = 2543190
+ },
+ /* MODEL 3 */
+ { .offset = -15650652,
+ .slope = 1565065
+ },
+ },
+ /* CPUFREQ has no correction (and is not implemented at all) */
+};
+
+struct pm121_connection {
+ unsigned int control_id;
+ unsigned int ref_id;
+ struct pm121_correction correction;
+};
+
+static struct pm121_connection pm121_connections[] = {
+ /* MODEL 2 */
+ { .control_id = FAN_CPU,
+ .ref_id = FAN_OD,
+ { .offset = -32768000,
+ .slope = 65536
+ }
+ },
+ /* MODEL 3 */
+ { .control_id = FAN_OD,
+ .ref_id = FAN_HD,
+ { .offset = -32768000,
+ .slope = 65536
+ }
+ },
+};
+
+/* pointer to the current model connection */
+static struct pm121_connection *pm121_connection;
+
+/*
+ * ****** System Fans Control Loop ******
+ *
+ */
+
+/* Since each loop handles only one control and we want to avoid
+ * writing virtual control, we store the control correction with the
+ * loop params. Some data are not set, there are common to all loop
+ * and thus, hardcoded.
+ */
+struct pm121_sys_param {
+ /* purely informative since we use mach_model-2 as index */
+ int model_id;
+ struct wf_sensor **sensor; /* use sensor_id instead ? */
+ s32 gp, itarget;
+ unsigned int control_id;
+};
+
+static struct pm121_sys_param
+pm121_sys_all_params[N_LOOPS][PM121_NUM_CONFIGS] = {
+ /* GPU Fan control loop */
+ {
+ { .model_id = 2,
+ .sensor = &sensor_gpu_temp,
+ .gp = 0x002A6666,
+ .itarget = 0x5A0000,
+ .control_id = FAN_HD,
+ },
+ { .model_id = 3,
+ .sensor = &sensor_gpu_temp,
+ .gp = 0x0010CCCC,
+ .itarget = 0x500000,
+ .control_id = FAN_CPU,
+ },
+ },
+ /* HD Fan control loop */
+ {
+ { .model_id = 2,
+ .sensor = &sensor_hard_drive_temp,
+ .gp = 0x002D70A3,
+ .itarget = 0x370000,
+ .control_id = FAN_HD,
+ },
+ { .model_id = 3,
+ .sensor = &sensor_hard_drive_temp,
+ .gp = 0x002170A3,
+ .itarget = 0x370000,
+ .control_id = FAN_HD,
+ },
+ },
+ /* KODIAK Fan control loop */
+ {
+ { .model_id = 2,
+ .sensor = &sensor_north_bridge_temp,
+ .gp = 0x003BD70A,
+ .itarget = 0x550000,
+ .control_id = FAN_OD,
+ },
+ { .model_id = 3,
+ .sensor = &sensor_north_bridge_temp,
+ .gp = 0x0030F5C2,
+ .itarget = 0x550000,
+ .control_id = FAN_HD,
+ },
+ },
+ /* OD Fan control loop */
+ {
+ { .model_id = 2,
+ .sensor = &sensor_optical_drive_temp,
+ .gp = 0x001FAE14,
+ .itarget = 0x320000,
+ .control_id = FAN_OD,
+ },
+ { .model_id = 3,
+ .sensor = &sensor_optical_drive_temp,
+ .gp = 0x001FAE14,
+ .itarget = 0x320000,
+ .control_id = FAN_OD,
+ },
+ },
+};
+
+/* the hardcoded values */
+#define PM121_SYS_GD 0x00000000
+#define PM121_SYS_GR 0x00019999
+#define PM121_SYS_HISTORY_SIZE 2
+#define PM121_SYS_INTERVAL 5
+
+/* State data used by the system fans control loop
+ */
+struct pm121_sys_state {
+ int ticks;
+ s32 setpoint;
+ struct wf_pid_state pid;
+};
+
+struct pm121_sys_state *pm121_sys_state[N_LOOPS] = {};
+
+/*
+ * ****** CPU Fans Control Loop ******
+ *
+ */
+
+#define PM121_CPU_INTERVAL 1
+
+/* State data used by the cpu fans control loop
+ */
+struct pm121_cpu_state {
+ int ticks;
+ s32 setpoint;
+ struct wf_cpu_pid_state pid;
+};
+
+static struct pm121_cpu_state *pm121_cpu_state;
+
+
+
+/*
+ * ***** Implementation *****
+ *
+ */
+
+/* correction the value using the output-low-bound correction algo */
+static s32 pm121_correct(s32 new_setpoint,
+ unsigned int control_id,
+ s32 min)
+{
+ s32 new_min;
+ struct pm121_correction *correction;
+ correction = &corrections[control_id][pm121_mach_model - 2];
+
+ new_min = (average_power * correction->slope) >> 16;
+ new_min += correction->offset;
+ new_min = (new_min >> 16) + min;
+
+ return max(new_setpoint, max(new_min, 0));
+}
+
+static s32 pm121_connect(unsigned int control_id, s32 setpoint)
+{
+ s32 new_min, value, new_setpoint;
+
+ if (pm121_connection->control_id == control_id) {
+ controls[control_id]->ops->get_value(controls[control_id],
+ &value);
+ new_min = value * pm121_connection->correction.slope;
+ new_min += pm121_connection->correction.offset;
+ if (new_min > 0) {
+ new_setpoint = max(setpoint, (new_min >> 16));
+ if (new_setpoint != setpoint) {
+ DBG("pm121: %s depending on %s, "
+ "corrected from %d to %d RPM\n",
+ controls[control_id]->name,
+ controls[pm121_connection->ref_id]->name,
+ (int) setpoint, (int) new_setpoint);
+ }
+ } else
+ new_setpoint = setpoint;
+ }
+ /* no connection */
+ else
+ new_setpoint = setpoint;
+
+ return new_setpoint;
+}
+
+/* FAN LOOPS */
+static void pm121_create_sys_fans(int loop_id)
+{
+ struct pm121_sys_param *param = NULL;
+ struct wf_pid_param pid_param;
+ struct wf_control *control = NULL;
+ int i;
+
+ /* First, locate the params for this model */
+ for (i = 0; i < PM121_NUM_CONFIGS; i++) {
+ if (pm121_sys_all_params[loop_id][i].model_id == pm121_mach_model) {
+ param = &(pm121_sys_all_params[loop_id][i]);
+ break;
+ }
+ }
+
+ /* No params found, put fans to max */
+ if (param == NULL) {
+ printk(KERN_WARNING "pm121: %s fan config not found "
+ " for this machine model\n",
+ loop_names[loop_id]);
+ goto fail;
+ }
+
+ control = controls[param->control_id];
+
+ /* Alloc & initialize state */
+ pm121_sys_state[loop_id] = kmalloc(sizeof(struct pm121_sys_state),
+ GFP_KERNEL);
+ if (pm121_sys_state[loop_id] == NULL) {
+ printk(KERN_WARNING "pm121: Memory allocation error\n");
+ goto fail;
+ }
+ pm121_sys_state[loop_id]->ticks = 1;
+
+ /* Fill PID params */
+ pid_param.gd = PM121_SYS_GD;
+ pid_param.gp = param->gp;
+ pid_param.gr = PM121_SYS_GR;
+ pid_param.interval = PM121_SYS_INTERVAL;
+ pid_param.history_len = PM121_SYS_HISTORY_SIZE;
+ pid_param.itarget = param->itarget;
+ pid_param.min = control->ops->get_min(control);
+ pid_param.max = control->ops->get_max(control);
+
+ wf_pid_init(&pm121_sys_state[loop_id]->pid, &pid_param);
+
+ DBG("pm121: %s Fan control loop initialized.\n"
+ " itarged=%d.%03d, min=%d RPM, max=%d RPM\n",
+ loop_names[loop_id], FIX32TOPRINT(pid_param.itarget),
+ pid_param.min, pid_param.max);
+ return;
+
+ fail:
+ /* note that this is not optimal since another loop may still
+ control the same control */
+ printk(KERN_WARNING "pm121: failed to set up %s loop "
+ "setting \"%s\" to max speed.\n",
+ loop_names[loop_id], control->name);
+
+ if (control)
+ wf_control_set_max(control);
+}
+
+static void pm121_sys_fans_tick(int loop_id)
+{
+ struct pm121_sys_param *param;
+ struct pm121_sys_state *st;
+ struct wf_sensor *sensor;
+ struct wf_control *control;
+ s32 temp, new_setpoint;
+ int rc;
+
+ param = &(pm121_sys_all_params[loop_id][pm121_mach_model-2]);
+ st = pm121_sys_state[loop_id];
+ sensor = *(param->sensor);
+ control = controls[param->control_id];
+
+ if (--st->ticks != 0) {
+ if (pm121_readjust)
+ goto readjust;
+ return;
+ }
+ st->ticks = PM121_SYS_INTERVAL;
+
+ rc = sensor->ops->get_value(sensor, &temp);
+ if (rc) {
+ printk(KERN_WARNING "windfarm: %s sensor error %d\n",
+ sensor->name, rc);
+ pm121_failure_state |= FAILURE_SENSOR;
+ return;
+ }
+
+ DBG("pm121: %s Fan tick ! %s: %d.%03d\n",
+ loop_names[loop_id], sensor->name,
+ FIX32TOPRINT(temp));
+
+ new_setpoint = wf_pid_run(&st->pid, temp);
+
+ /* correction */
+ new_setpoint = pm121_correct(new_setpoint,
+ param->control_id,
+ st->pid.param.min);
+ /* linked corretion */
+ new_setpoint = pm121_connect(param->control_id, new_setpoint);
+
+ if (new_setpoint == st->setpoint)
+ return;
+ st->setpoint = new_setpoint;
+ DBG("pm121: %s corrected setpoint: %d RPM\n",
+ control->name, (int)new_setpoint);
+ readjust:
+ if (control && pm121_failure_state == 0) {
+ rc = control->ops->set_value(control, st->setpoint);
+ if (rc) {
+ printk(KERN_WARNING "windfarm: %s fan error %d\n",
+ control->name, rc);
+ pm121_failure_state |= FAILURE_FAN;
+ }
+ }
+}
+
+
+/* CPU LOOP */
+static void pm121_create_cpu_fans(void)
+{
+ struct wf_cpu_pid_param pid_param;
+ const struct smu_sdbp_header *hdr;
+ struct smu_sdbp_cpupiddata *piddata;
+ struct smu_sdbp_fvt *fvt;
+ struct wf_control *fan_cpu;
+ s32 tmax, tdelta, maxpow, powadj;
+
+ fan_cpu = controls[FAN_CPU];
+
+ /* First, locate the PID params in SMU SBD */
+ hdr = smu_get_sdb_partition(SMU_SDB_CPUPIDDATA_ID, NULL);
+ if (hdr == 0) {
+ printk(KERN_WARNING "pm121: CPU PID fan config not found.\n");
+ goto fail;
+ }
+ piddata = (struct smu_sdbp_cpupiddata *)&hdr[1];
+
+ /* Get the FVT params for operating point 0 (the only supported one
+ * for now) in order to get tmax
+ */
+ hdr = smu_get_sdb_partition(SMU_SDB_FVT_ID, NULL);
+ if (hdr) {
+ fvt = (struct smu_sdbp_fvt *)&hdr[1];
+ tmax = ((s32)fvt->maxtemp) << 16;
+ } else
+ tmax = 0x5e0000; /* 94 degree default */
+
+ /* Alloc & initialize state */
+ pm121_cpu_state = kmalloc(sizeof(struct pm121_cpu_state),
+ GFP_KERNEL);
+ if (pm121_cpu_state == NULL)
+ goto fail;
+ pm121_cpu_state->ticks = 1;
+
+ /* Fill PID params */
+ pid_param.interval = PM121_CPU_INTERVAL;
+ pid_param.history_len = piddata->history_len;
+ if (pid_param.history_len > WF_CPU_PID_MAX_HISTORY) {
+ printk(KERN_WARNING "pm121: History size overflow on "
+ "CPU control loop (%d)\n", piddata->history_len);
+ pid_param.history_len = WF_CPU_PID_MAX_HISTORY;
+ }
+ pid_param.gd = piddata->gd;
+ pid_param.gp = piddata->gp;
+ pid_param.gr = piddata->gr / pid_param.history_len;
+
+ tdelta = ((s32)piddata->target_temp_delta) << 16;
+ maxpow = ((s32)piddata->max_power) << 16;
+ powadj = ((s32)piddata->power_adj) << 16;
+
+ pid_param.tmax = tmax;
+ pid_param.ttarget = tmax - tdelta;
+ pid_param.pmaxadj = maxpow - powadj;
+
+ pid_param.min = fan_cpu->ops->get_min(fan_cpu);
+ pid_param.max = fan_cpu->ops->get_max(fan_cpu);
+
+ wf_cpu_pid_init(&pm121_cpu_state->pid, &pid_param);
+
+ DBG("pm121: CPU Fan control initialized.\n");
+ DBG(" ttarged=%d.%03d, tmax=%d.%03d, min=%d RPM, max=%d RPM,\n",
+ FIX32TOPRINT(pid_param.ttarget), FIX32TOPRINT(pid_param.tmax),
+ pid_param.min, pid_param.max);
+
+ return;
+
+ fail:
+ printk(KERN_WARNING "pm121: CPU fan config not found, max fan speed\n");
+
+ if (controls[CPUFREQ])
+ wf_control_set_max(controls[CPUFREQ]);
+ if (fan_cpu)
+ wf_control_set_max(fan_cpu);
+}
+
+
+static void pm121_cpu_fans_tick(struct pm121_cpu_state *st)
+{
+ s32 new_setpoint, temp, power;
+ struct wf_control *fan_cpu = NULL;
+ int rc;
+
+ if (--st->ticks != 0) {
+ if (pm121_readjust)
+ goto readjust;
+ return;
+ }
+ st->ticks = PM121_CPU_INTERVAL;
+
+ fan_cpu = controls[FAN_CPU];
+
+ rc = sensor_cpu_temp->ops->get_value(sensor_cpu_temp, &temp);
+ if (rc) {
+ printk(KERN_WARNING "pm121: CPU temp sensor error %d\n",
+ rc);
+ pm121_failure_state |= FAILURE_SENSOR;
+ return;
+ }
+
+ rc = sensor_cpu_power->ops->get_value(sensor_cpu_power, &power);
+ if (rc) {
+ printk(KERN_WARNING "pm121: CPU power sensor error %d\n",
+ rc);
+ pm121_failure_state |= FAILURE_SENSOR;
+ return;
+ }
+
+ DBG("pm121: CPU Fans tick ! CPU temp: %d.%03d°C, power: %d.%03d\n",
+ FIX32TOPRINT(temp), FIX32TOPRINT(power));
+
+#ifdef HACKED_OVERTEMP
+#define MAX 0x4a0000
+#else
+#define MAX st->pid.param.tmax
+#endif
+ if (temp > MAX)
+ pm121_failure_state |= FAILURE_OVERTEMP;
+
+#undef MAX
+
+ new_setpoint = wf_cpu_pid_run(&st->pid, power, temp);
+
+ /* correction */
+ new_setpoint = pm121_correct(new_setpoint,
+ FAN_CPU,
+ st->pid.param.min);
+
+ /* connected correction */
+ new_setpoint = pm121_connect(FAN_CPU, new_setpoint);
+
+ if (st->setpoint == new_setpoint)
+ return;
+ st->setpoint = new_setpoint;
+ DBG("pm121: CPU corrected setpoint: %d RPM\n", (int)new_setpoint);
+
+ readjust:
+ if (fan_cpu && pm121_failure_state == 0) {
+ rc = fan_cpu->ops->set_value(fan_cpu, st->setpoint);
+ if (rc) {
+ printk(KERN_WARNING "pm121: %s fan error %d\n",
+ fan_cpu->name, rc);
+ pm121_failure_state |= FAILURE_FAN;
+ }
+ }
+}
+
+/*
+ * ****** Common ******
+ *
+ */
+
+static void pm121_tick(void)
+{
+ unsigned int last_failure = pm121_failure_state;
+ unsigned int new_failure;
+ s32 total_power;
+ int i;
+
+ if (!pm121_started) {
+ DBG("pm121: creating control loops !\n");
+ for (i = 0; i < N_LOOPS; i++)
+ pm121_create_sys_fans(i);
+
+ pm121_create_cpu_fans();
+ pm121_started = 1;
+ }
+
+ /* skipping ticks */
+ if (pm121_skipping && --pm121_skipping)
+ return;
+
+ /* compute average power */
+ total_power = 0;
+ for (i = 0; i < pm121_cpu_state->pid.param.history_len; i++)
+ total_power += pm121_cpu_state->pid.powers[i];
+
+ average_power = total_power / pm121_cpu_state->pid.param.history_len;
+
+
+ pm121_failure_state = 0;
+ for (i = 0 ; i < N_LOOPS; i++) {
+ if (pm121_sys_state[i])
+ pm121_sys_fans_tick(i);
+ }
+
+ if (pm121_cpu_state)
+ pm121_cpu_fans_tick(pm121_cpu_state);
+
+ pm121_readjust = 0;
+ new_failure = pm121_failure_state & ~last_failure;
+
+ /* If entering failure mode, clamp cpufreq and ramp all
+ * fans to full speed.
+ */
+ if (pm121_failure_state && !last_failure) {
+ for (i = 0; i < N_CONTROLS; i++) {
+ if (controls[i])
+ wf_control_set_max(controls[i]);
+ }
+ }
+
+ /* If leaving failure mode, unclamp cpufreq and readjust
+ * all fans on next iteration
+ */
+ if (!pm121_failure_state && last_failure) {
+ if (controls[CPUFREQ])
+ wf_control_set_min(controls[CPUFREQ]);
+ pm121_readjust = 1;
+ }
+
+ /* Overtemp condition detected, notify and start skipping a couple
+ * ticks to let the temperature go down
+ */
+ if (new_failure & FAILURE_OVERTEMP) {
+ wf_set_overtemp();
+ pm121_skipping = 2;
+ }
+
+ /* We only clear the overtemp condition if overtemp is cleared
+ * _and_ no other failure is present. Since a sensor error will
+ * clear the overtemp condition (can't measure temperature) at
+ * the control loop levels, but we don't want to keep it clear
+ * here in this case
+ */
+ if (new_failure == 0 && last_failure & FAILURE_OVERTEMP)
+ wf_clear_overtemp();
+}
+
+
+
+
+#define pm121_register_control(control, match, id) \
+ if (controls[id] == NULL && !strcmp(control->name,match)) { \
+ if (wf_get_control(control) == 0) \
+ controls[id] = control; \
+ } \
+ all = all && controls[id];
+
+static void pm121_new_control(struct wf_control *ct)
+{
+ int all = 1;
+
+ if (pm121_all_controls_ok)
+ return;
+
+ pm121_register_control(ct, "optical-drive-fan", FAN_OD);
+ pm121_register_control(ct, "hard-drive-fan", FAN_HD);
+ pm121_register_control(ct, "cpu-fan", FAN_CPU);
+ pm121_register_control(ct, "cpufreq-clamp", CPUFREQ);
+
+ if (all)
+ pm121_all_controls_ok = 1;
+}
+#undef pm121_register_control
+
+
+
+
+#define pm121_register_sensor(sensor, match, var) \
+ if (var == NULL && !strcmp(sensor->name,match)) { \
+ if (wf_get_sensor(sensor) == 0) \
+ var = sensor; \
+ } \
+ all = all && var;
+
+static void pm121_new_sensor(struct wf_sensor *sr)
+{
+ int all = 1;
+
+ if (pm121_all_sensors_ok)
+ return;
+
+ pm121_register_sensor(sr, "cpu-temp",
+ sensor_cpu_temp);
+ pm121_register_sensor(sr, "cpu-current",
+ sensor_cpu_current);
+ pm121_register_sensor(sr, "cpu-voltage",
+ sensor_cpu_voltage);
+ pm121_register_sensor(sr, "cpu-power",
+ sensor_cpu_power);
+ pm121_register_sensor(sr, "hard-drive-temp",
+ sensor_hard_drive_temp);
+ pm121_register_sensor(sr, "optical-drive-temp",
+ sensor_optical_drive_temp);
+ pm121_register_sensor(sr, "incoming-air-temp",
+ sensor_incoming_air_temp);
+ pm121_register_sensor(sr, "north-bridge-temp",
+ sensor_north_bridge_temp);
+ pm121_register_sensor(sr, "gpu-temp",
+ sensor_gpu_temp);
+
+ if (all)
+ pm121_all_sensors_ok = 1;
+}
+
+#undef pm121_register_sensor
+
+
+
+static int pm121_notify(struct notifier_block *self,
+ unsigned long event, void *data)
+{
+ switch (event) {
+ case WF_EVENT_NEW_CONTROL:
+ DBG("pm121: new control %s detected\n",
+ ((struct wf_control *)data)->name);
+ pm121_new_control(data);
+ break;
+ case WF_EVENT_NEW_SENSOR:
+ DBG("pm121: new sensor %s detected\n",
+ ((struct wf_sensor *)data)->name);
+ pm121_new_sensor(data);
+ break;
+ case WF_EVENT_TICK:
+ if (pm121_all_controls_ok && pm121_all_sensors_ok)
+ pm121_tick();
+ break;
+ }
+
+ return 0;
+}
+
+static struct notifier_block pm121_events = {
+ .notifier_call = pm121_notify,
+};
+
+static int pm121_init_pm(void)
+{
+ const struct smu_sdbp_header *hdr;
+
+ hdr = smu_get_sdb_partition(SMU_SDB_SENSORTREE_ID, NULL);
+ if (hdr != 0) {
+ struct smu_sdbp_sensortree *st =
+ (struct smu_sdbp_sensortree *)&hdr[1];
+ pm121_mach_model = st->model_id;
+ }
+
+ pm121_connection = &pm121_connections[pm121_mach_model - 2];
+
+ printk(KERN_INFO "pm121: Initializing for iMac G5 iSight model ID %d\n",
+ pm121_mach_model);
+
+ return 0;
+}
+
+
+static int pm121_probe(struct platform_device *ddev)
+{
+ wf_register_client(&pm121_events);
+
+ return 0;
+}
+
+static int __devexit pm121_remove(struct platform_device *ddev)
+{
+ wf_unregister_client(&pm121_events);
+ return 0;
+}
+
+static struct platform_driver pm121_driver = {
+ .probe = pm121_probe,
+ .remove = __devexit_p(pm121_remove),
+ .driver = {
+ .name = "windfarm",
+ .bus = &platform_bus_type,
+ },
+};
+
+
+static int __init pm121_init(void)
+{
+ int rc = -ENODEV;
+
+ if (machine_is_compatible("PowerMac12,1"))
+ rc = pm121_init_pm();
+
+ if (rc == 0) {
+#ifdef MODULE
+ request_module("windfarm_smu_controls");
+ request_module("windfarm_smu_sensors");
+ request_module("windfarm_smu_sat");
+ request_module("windfarm_lm75_sensor");
+ request_module("windfarm_max6690_sensor");
+ request_module("windfarm_cpufreq_clamp");
+
+#endif /* MODULE */
+ platform_driver_register(&pm121_driver);
+ }
+
+ return rc;
+}
+
+static void __exit pm121_exit(void)
+{
+
+ platform_driver_unregister(&pm121_driver);
+}
+
+
+module_init(pm121_init);
+module_exit(pm121_exit);
+
+MODULE_AUTHOR("Étienne Bersac <bersace@gmail.com>");
+MODULE_DESCRIPTION("Thermal control logic for iMac G5 (iSight)");
+MODULE_LICENSE("GPL");
+
diff --git a/drivers/macintosh/windfarm_smu_controls.c b/drivers/macintosh/windfarm_smu_controls.c
index 58c2590..961fa0e 100644
--- a/drivers/macintosh/windfarm_smu_controls.c
+++ b/drivers/macintosh/windfarm_smu_controls.c
@@ -218,6 +218,10 @@ static struct smu_fan_control *smu_fan_create(struct device_node *node,
fct->ctrl.name = "cpu-fan";
else if (!strcmp(l, "Hard Drive") || !strcmp(l, "Hard drive"))
fct->ctrl.name = "drive-bay-fan";
+ else if (!strcmp(l, "HDD Fan")) /* seen on iMac G5 iSight */
+ fct->ctrl.name = "hard-drive-fan";
+ else if (!strcmp(l, "ODD Fan")) /* same */
+ fct->ctrl.name = "optical-drive-fan";
/* Unrecognized fan, bail out */
if (fct->ctrl.name == NULL)
^ permalink raw reply related
* Re: [PATCH 3/4] Convert PowerPC MPC i2c to of_platform_driver from platform_driver
From: Kumar Gala @ 2007-12-10 15:34 UTC (permalink / raw)
To: Jon Smirl; +Cc: linuxppc-dev, i2c
In-Reply-To: <20071209233654.2327.18925.stgit@terra.home>
On Dec 9, 2007, at 5:36 PM, Jon Smirl wrote:
> Convert MPC i2c driver from being a platform_driver to an open
> firmware version. Error returns were improved. Routine names were
> changed from fsl_ to mpc_ to make them match the file name.
>
> Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
> ---
>
> arch/powerpc/sysdev/fsl_soc.c | 96 ---------------------
> drivers/i2c/busses/i2c-mpc.c | 190 +++++++++++++++++++++++++++
> +-------------
> 2 files changed, 129 insertions(+), 157 deletions(-)
this patch breaks arch/ppc users which are platform_driver based and
I'm guessing a number of arch/powerpc users which don't
of_platform_bus_probe().
Also, you should split out the conversion and error fixing into
separate patches.
- k
^ permalink raw reply
* Re: [PATCH] windfarm: add PowerMac 12,1 support
From: Arnd Bergmann @ 2007-12-10 15:39 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1197299517.6822.2.camel@thilivren>
On Monday 10 December 2007, =C3=89tienne Bersac wrote:
> From: =C3=89tienne Bersac <bersace03@gmail.com>
>=20
> Here is an updated patch that fix the potential bug, CPU param detection
> failure might not be detected. Please review it.=20
I didn't find much interesting to complain about, just a few style
issues that could be improved. Good work!
> -static void wf_max6690_create(struct i2c_adapter *adapter, u8 addr)
> +static void wf_max6690_create(struct i2c_adapter *adapter, u8 addr,
> + const char *loc)
> {
> struct wf_6690_sensor *max;
> - char *name =3D "backside-temp";
> + char *name =3D NULL;
> =20
It's better not to initialize local variables like this one, instead of
assigning them to 0 or NULL. When it's not initialized, gcc is able to
warn about cases where you don't assign a meaningful value before using
it.
> +#undef DEBUG
> +
> +#ifdef DEBUG
> +#define DBG(args...) printk(args)
> +#else
> +#define DBG(args...) do { } while (0)
> +#endif
Don't define your own macros like these, but instead use the ones that
are there. If possible, use 'dev_dbg()', otherwise 'pr_debug()'.
> +static int pm121_mach_model; /* machine model id */
> +
> +/* Controls & sensors */
> +static struct wf_sensor *sensor_cpu_power;
> +static struct wf_sensor *sensor_cpu_temp;
> +static struct wf_sensor *sensor_cpu_voltage;
> +static struct wf_sensor *sensor_cpu_current;
> +static struct wf_sensor *sensor_gpu_temp;
> +static struct wf_sensor *sensor_north_bridge_temp;
> +static struct wf_sensor *sensor_hard_drive_temp;
> +static struct wf_sensor *sensor_optical_drive_temp;
> +static struct wf_sensor *sensor_incoming_air_temp; /* unused ! */
> +static struct wf_control *controls[N_CONTROLS] =3D {};
> +
> +static unsigned int pm121_failure_state;
> +static int pm121_readjust, pm121_skipping;
> +static s32 average_power;
Having many global variables is typically a sign that you are doing
something wrong. It's better to attach all the data you have to your
device structure.
Have you checked that you are doing the right locking when accessing
these variables from concurrent threads?
> +struct pm121_correction {
> + int offset;
> + int slope;
> +};
> +
> +struct pm121_correction corrections[N_CONTROLS][PM121_NUM_CONFIGS] =3D {
This looks like it could be 'const'. 'static const' variables are better
because it becomes obvious that you don't need locking to access them.
> +static struct pm121_connection pm121_connections[] =3D {
same here.
> +static struct pm121_sys_param
> +pm121_sys_all_params[N_LOOPS][PM121_NUM_CONFIGS] =3D {
and here.
> +#ifdef HACKED_OVERTEMP
> +#define MAX 0x4a0000
> +#else
> +#define MAX st->pid.param.tmax
> +#endif
> + if (temp > MAX)
> + pm121_failure_state |=3D FAILURE_OVERTEMP;
> +
> +#undef MAX
You don't define HACKED_OVERTEMP anywhere, so you basicall have dead
code here. It's probably better to remove that for the upstream version,
even if it was helpful for your debugging.
> +
> +#define pm121_register_control(control, match, id) \
> + if (controls[id] =3D=3D NULL && !strcmp(control->name,match)) { \
> + if (wf_get_control(control) =3D=3D 0) \
> + controls[id] =3D control; \
> + } \
> + all =3D all && controls[id];
Does this need to be a macro? If possible, use static functions
for this kind of stuff. They will normally be inlined, which gives
you the same object code in the end.
> +static int __init pm121_init(void)
> +{
> + int rc =3D -ENODEV;
> +
> + if (machine_is_compatible("PowerMac12,1"))
> + rc =3D pm121_init_pm();
> +
> + if (rc =3D=3D 0) {
> +#ifdef MODULE
> + request_module("windfarm_smu_controls");
> + request_module("windfarm_smu_sensors");
> + request_module("windfarm_smu_sat");
> + request_module("windfarm_lm75_sensor");
> + request_module("windfarm_max6690_sensor");
> + request_module("windfarm_cpufreq_clamp");
> +
> +#endif /* MODULE */
> + platform_driver_register(&pm121_driver);
> + }
> +
> + return rc;
> +}
Why the #ifdef MODULE here? It's normally better to have identical
code for modular and built-in cases.
Arnd <><
^ permalink raw reply
* Re: [PATCH 3/4] Convert PowerPC MPC i2c to of_platform_driver from platform_driver
From: Jon Smirl @ 2007-12-10 16:12 UTC (permalink / raw)
To: Kumar Gala; +Cc: linuxppc-dev, i2c
In-Reply-To: <1E5FF6FC-E905-4FAF-84ED-A96B0E0ACCA8@kernel.crashing.org>
On 12/10/07, Kumar Gala <galak@kernel.crashing.org> wrote:
>
> On Dec 9, 2007, at 5:36 PM, Jon Smirl wrote:
>
> > Convert MPC i2c driver from being a platform_driver to an open
> > firmware version. Error returns were improved. Routine names were
> > changed from fsl_ to mpc_ to make them match the file name.
> >
> > Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
> > ---
> >
> > arch/powerpc/sysdev/fsl_soc.c | 96 ---------------------
> > drivers/i2c/busses/i2c-mpc.c | 190 +++++++++++++++++++++++++++
> > +-------------
> > 2 files changed, 129 insertions(+), 157 deletions(-)
>
> this patch breaks arch/ppc users which are platform_driver based and
> I'm guessing a number of arch/powerpc users which don't
> of_platform_bus_probe().
We should just make two copies of the driver. All of this is needed to
allow automatic loading of the correct i2c modules as dictated by the
device tree. I'm working on the same support for automatically loading
audio codec drivers.
> Also, you should split out the conversion and error fixing into
> separate patches.
I can spin another revision to move those nine lines adding missing
error returns to another patch.
>
> - k
>
--
Jon Smirl
jonsmirl@gmail.com
^ permalink raw reply
* Re: Xilinx ML310 Linux 2.6 PCI bridge
From: Jean-Samuel Chenard @ 2007-12-10 16:33 UTC (permalink / raw)
To: Stephen Neuendorffer; +Cc: linuxppc-embedded
In-Reply-To: <20071210054659.D373C16006E@mail51-dub.bigfish.com>
On Dec 10, 2007 12:46 AM, Stephen Neuendorffer
<stephen.neuendorffer@xilinx.com> wrote:
> I would strongly recommend not spending a huge amount of time on the ml31=
0.
> The University program board is dirt cheap for universities, very well
> supported under Linux, using either secretlab.ca or git.xilinx.com and yo=
u
> won't spend your time getting PCI to place and route correctly, followed =
by
> figuring out how to get Linux to talk to it nicely.
Hi Stephen,
Thanks for the insight. I was aware of the XUP V2P board and I think
this is a nice initiative to let students use some great technology.
> If your lab can afford a bee2, then you should be able to afford one (or
> better yet, several) xupv2p's to go with it.
That's where things get complicated... In our lab, we get expensive
hardware such as the BEE2 via CMC Microsystems (a Canadian granting
agency). However, getting funds locally to buy other equipment is a
relatively long and administratively complex process...
One of my colleague did not use his ML-310 board so I got a hold of it
(in a day, with little overhead). So far, the ML-310 has helped me
bring up Linux 2.6 and experiment most of what I need to use on the
BEE2. I am only missing the networking. This would make things much
nicer to work via a NFS-exported root file system. However, I'm OK
swapping the CompactFlash card...
I find it strange that Xilinx would not invest in supporting Linux 2.6
for an important feature such as a PCI bridge (not specifically for
the ML-310, but in general) when this can bring many interesting
benefits to an embedded platform. Is this something that is "in
progress" at Xilinx? You seem to imply that most of the difficulty in
getting the PCI core working is in meeting the timing requirements
(not with the SW drivers), so I might be missing driver files when I
generate the BSP code for Linux 2.6.
Regards,
Jean-Samuel
--=20
Integrated Microsystems Laboratory
McGill University, Montr=E9al, QC, CANADA
Web Page: http://chaos.ece.mcgill.ca
^ permalink raw reply
* [PATCH] mpc8272ads, pq2fads: Update defconfig with CONFIG_FS_ENET_MDIO_FCC
From: Scott Wood @ 2007-12-10 17:10 UTC (permalink / raw)
To: galak; +Cc: linuxppc-dev
This was recently made configurable, and needs to be set for these boards.
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
Please apply for 2.6.24.
arch/powerpc/configs/mpc8272_ads_defconfig | 110 +++++++++++---------
arch/powerpc/configs/pq2fads_defconfig | 152 +++++++++++++++++-----------
2 files changed, 153 insertions(+), 109 deletions(-)
diff --git a/arch/powerpc/configs/mpc8272_ads_defconfig b/arch/powerpc/configs/mpc8272_ads_defconfig
index 865a942..e982a29 100644
--- a/arch/powerpc/configs/mpc8272_ads_defconfig
+++ b/arch/powerpc/configs/mpc8272_ads_defconfig
@@ -1,7 +1,7 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.23-rc4
-# Wed Sep 5 12:43:23 2007
+# Linux kernel version: 2.6.24-rc3
+# Mon Dec 10 11:02:24 2007
#
# CONFIG_PPC64 is not set
@@ -20,8 +20,13 @@ CONFIG_PPC_STD_MMU_32=y
# CONFIG_PPC_MM_SLICES is not set
# CONFIG_SMP is not set
CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
CONFIG_PPC_MERGE=y
CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_IRQ_PER_CPU=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
@@ -63,6 +68,10 @@ CONFIG_SYSVIPC_SYSCTL=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
# CONFIG_BLK_DEV_INITRD is not set
@@ -81,7 +90,6 @@ CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
-CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
@@ -115,7 +123,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory"
# Platform support
#
# CONFIG_PPC_MULTIPLATFORM is not set
-# CONFIG_EMBEDDED6xx is not set
CONFIG_PPC_82xx=y
# CONFIG_PPC_83xx is not set
# CONFIG_PPC_86xx is not set
@@ -124,6 +131,7 @@ CONFIG_PPC_82xx=y
# CONFIG_PPC_CELL is not set
# CONFIG_PPC_CELL_NATIVE is not set
CONFIG_MPC8272_ADS=y
+# CONFIG_PQ2FADS is not set
CONFIG_PQ2ADS=y
CONFIG_8260=y
CONFIG_8272=y
@@ -147,6 +155,10 @@ CONFIG_CPM=y
# Kernel options
#
# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_300 is not set
@@ -163,6 +175,7 @@ CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
@@ -171,9 +184,10 @@ CONFIG_VIRT_TO_BUS=y
CONFIG_PROC_DEVICETREE=y
# CONFIG_CMDLINE_BOOL is not set
# CONFIG_PM is not set
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
CONFIG_SECCOMP=y
CONFIG_WANT_DEVICE_TREE=y
-# CONFIG_BUILD_RAW_IMAGE is not set
CONFIG_DEVICE_TREE="mpc8272ads.dts"
CONFIG_ISA_DMA_API=y
@@ -190,11 +204,8 @@ CONFIG_PCI_8260=y
# CONFIG_PCIEPORTBUS is not set
CONFIG_ARCH_SUPPORTS_MSI=y
# CONFIG_PCI_MSI is not set
+CONFIG_PCI_LEGACY=y
# CONFIG_PCI_DEBUG is not set
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
# CONFIG_PCCARD is not set
#
@@ -208,7 +219,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y
CONFIG_HIGHMEM_START=0xfe000000
CONFIG_LOWMEM_SIZE=0x30000000
CONFIG_KERNEL_START=0xc0000000
-CONFIG_TASK_SIZE=0x80000000
+CONFIG_TASK_SIZE=0xc0000000
CONFIG_BOOT_LOAD=0x00400000
#
@@ -245,6 +256,7 @@ CONFIG_INET_TUNNEL=y
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
@@ -288,10 +300,6 @@ CONFIG_NETFILTER=y
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
-
-#
-# QoS and/or fair queueing
-#
# CONFIG_NET_SCHED is not set
#
@@ -317,6 +325,7 @@ CONFIG_NETFILTER=y
#
# Generic Driver Options
#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
@@ -340,6 +349,7 @@ CONFIG_MTD_BLOCK=y
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
#
# RAM/ROM/Flash chip drivers
@@ -378,6 +388,7 @@ CONFIG_MTD_CFI_UTIL=y
# CONFIG_MTD_PHYSMAP is not set
CONFIG_MTD_PHYSMAP_OF=y
# CONFIG_MTD_SBC8240 is not set
+# CONFIG_MTD_INTEL_VR_NOR is not set
# CONFIG_MTD_PLATRAM is not set
#
@@ -429,10 +440,6 @@ CONFIG_BLK_DEV_LOOP=y
# CONFIG_SCSI_NETLINK is not set
# CONFIG_ATA is not set
# CONFIG_MD is not set
-
-#
-# Fusion MPT device support
-#
# CONFIG_FUSION is not set
#
@@ -451,6 +458,7 @@ CONFIG_NETDEVICES=y
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=y
+# CONFIG_VETH is not set
# CONFIG_ARCNET is not set
CONFIG_PHYLIB=y
@@ -476,20 +484,28 @@ CONFIG_MII=y
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
# CONFIG_NET_PCI is not set
+# CONFIG_B44 is not set
CONFIG_FS_ENET=y
# CONFIG_FS_ENET_HAS_SCC is not set
CONFIG_FS_ENET_HAS_FCC=y
+CONFIG_FS_ENET_MDIO_FCC=y
CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
+# CONFIG_E1000E is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
+# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
@@ -497,11 +513,14 @@ CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
+# CONFIG_IXGBE is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
+# CONFIG_NIU is not set
# CONFIG_MLX4_CORE is not set
+# CONFIG_TEHUTI is not set
# CONFIG_TR is not set
#
@@ -539,7 +558,6 @@ CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
@@ -609,14 +627,11 @@ CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_IPMI_HANDLER is not set
-# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
# CONFIG_NVRAM is not set
# CONFIG_GEN_RTC is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
-# CONFIG_AGP is not set
-# CONFIG_DRM is not set
# CONFIG_RAW_DRIVER is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
@@ -629,6 +644,13 @@ CONFIG_DEVPORT=y
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
#
# Multifunction device drivers
@@ -645,16 +667,17 @@ CONFIG_DAB=y
#
# Graphics support
#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
-# CONFIG_VGASTATE is not set
-# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-# CONFIG_FB is not set
-# CONFIG_FB_IBM_GXT4500 is not set
#
# Sound
@@ -668,19 +691,6 @@ CONFIG_DAB=y
# CONFIG_RTC_CLASS is not set
#
-# DMA Engine support
-#
-# CONFIG_DMA_ENGINE is not set
-
-#
-# DMA Clients
-#
-
-#
-# DMA Devices
-#
-
-#
# Userspace I/O
#
# CONFIG_UIO is not set
@@ -696,7 +706,6 @@ CONFIG_EXT3_FS_XATTR=y
# CONFIG_EXT3_FS_POSIX_ACL is not set
# CONFIG_EXT3_FS_SECURITY is not set
CONFIG_JBD=y
-# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
@@ -736,7 +745,6 @@ CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
-CONFIG_RAMFS=y
#
# Miscellaneous filesystems
@@ -749,10 +757,7 @@ CONFIG_CRAMFS=y
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
+CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
@@ -790,10 +795,6 @@ CONFIG_MSDOS_PARTITION=y
# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
# CONFIG_SYSV68_PARTITION is not set
-
-#
-# Native Language Support
-#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
@@ -852,11 +853,15 @@ CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_INSTRUMENTATION=y
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
@@ -880,8 +885,11 @@ CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_PAGEALLOC is not set
@@ -924,8 +932,12 @@ CONFIG_CRYPTO_DES=y
# CONFIG_CRYPTO_ARC4 is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_SEED is not set
# CONFIG_CRYPTO_DEFLATE is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_AUTHENC is not set
# CONFIG_CRYPTO_HW is not set
+# CONFIG_PPC_CLOCK is not set
+CONFIG_PPC_LIB_RHEAP=y
diff --git a/arch/powerpc/configs/pq2fads_defconfig b/arch/powerpc/configs/pq2fads_defconfig
index 9191f55..6b17562 100644
--- a/arch/powerpc/configs/pq2fads_defconfig
+++ b/arch/powerpc/configs/pq2fads_defconfig
@@ -1,7 +1,7 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.23-rc4
-# Thu Aug 30 11:58:17 2007
+# Linux kernel version: 2.6.24-rc3
+# Mon Dec 10 11:01:07 2007
#
# CONFIG_PPC64 is not set
@@ -20,8 +20,13 @@ CONFIG_PPC_STD_MMU_32=y
# CONFIG_PPC_MM_SLICES is not set
# CONFIG_SMP is not set
CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
CONFIG_PPC_MERGE=y
CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_IRQ_PER_CPU=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
@@ -63,6 +68,10 @@ CONFIG_SYSVIPC_SYSCTL=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
# CONFIG_SYSFS_DEPRECATED is not set
# CONFIG_RELAY is not set
CONFIG_BLK_DEV_INITRD=y
@@ -82,7 +91,6 @@ CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
-CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
@@ -116,7 +124,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory"
# Platform support
#
# CONFIG_PPC_MULTIPLATFORM is not set
-# CONFIG_EMBEDDED6xx is not set
CONFIG_PPC_82xx=y
# CONFIG_PPC_83xx is not set
# CONFIG_PPC_86xx is not set
@@ -126,7 +133,6 @@ CONFIG_PPC_82xx=y
# CONFIG_PPC_CELL_NATIVE is not set
# CONFIG_MPC8272_ADS is not set
CONFIG_PQ2FADS=y
-# CONFIG_EP8248E is not set
CONFIG_PQ2ADS=y
CONFIG_8260=y
CONFIG_PQ2_ADS_PCI_PIC=y
@@ -149,6 +155,10 @@ CONFIG_CPM=y
# Kernel options
#
# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_300 is not set
@@ -165,6 +175,7 @@ CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
@@ -173,6 +184,8 @@ CONFIG_VIRT_TO_BUS=y
CONFIG_PROC_DEVICETREE=y
# CONFIG_CMDLINE_BOOL is not set
# CONFIG_PM is not set
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
CONFIG_SECCOMP=y
CONFIG_WANT_DEVICE_TREE=y
CONFIG_DEVICE_TREE="pq2fads.dts"
@@ -192,11 +205,8 @@ CONFIG_PCI_8260=y
# CONFIG_PCIEPORTBUS is not set
CONFIG_ARCH_SUPPORTS_MSI=y
# CONFIG_PCI_MSI is not set
+CONFIG_PCI_LEGACY=y
# CONFIG_PCI_DEBUG is not set
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
# CONFIG_PCCARD is not set
#
@@ -210,7 +220,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y
CONFIG_HIGHMEM_START=0xfe000000
CONFIG_LOWMEM_SIZE=0x30000000
CONFIG_KERNEL_START=0xc0000000
-CONFIG_TASK_SIZE=0x80000000
+CONFIG_TASK_SIZE=0xc0000000
CONFIG_BOOT_LOAD=0x00400000
#
@@ -247,6 +257,7 @@ CONFIG_INET_TUNNEL=y
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
@@ -290,10 +301,6 @@ CONFIG_NETFILTER=y
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
-
-#
-# QoS and/or fair queueing
-#
# CONFIG_NET_SCHED is not set
#
@@ -319,6 +326,7 @@ CONFIG_NETFILTER=y
#
# Generic Driver Options
#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
@@ -342,6 +350,7 @@ CONFIG_MTD_BLOCK=y
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
#
# RAM/ROM/Flash chip drivers
@@ -380,6 +389,7 @@ CONFIG_MTD_CFI_UTIL=y
# CONFIG_MTD_PHYSMAP is not set
CONFIG_MTD_PHYSMAP_OF=y
# CONFIG_MTD_SBC8240 is not set
+# CONFIG_MTD_INTEL_VR_NOR is not set
# CONFIG_MTD_PLATRAM is not set
#
@@ -442,10 +452,40 @@ CONFIG_IDE_PROC_FS=y
# IDE chipset support/bugfixes
#
# CONFIG_IDE_GENERIC is not set
-# CONFIG_BLK_DEV_IDEPCI is not set
+# CONFIG_BLK_DEV_PLATFORM is not set
+
+#
+# PCI IDE chipsets support
+#
# CONFIG_IDEPCI_PCIBUS_ORDER is not set
+# CONFIG_BLK_DEV_GENERIC is not set
+# CONFIG_BLK_DEV_AEC62XX is not set
+# CONFIG_BLK_DEV_ALI15X3 is not set
+# CONFIG_BLK_DEV_AMD74XX is not set
+# CONFIG_BLK_DEV_CMD64X is not set
+# CONFIG_BLK_DEV_TRIFLEX is not set
+# CONFIG_BLK_DEV_CY82C693 is not set
+# CONFIG_BLK_DEV_CS5530 is not set
+# CONFIG_BLK_DEV_HPT34X is not set
+# CONFIG_BLK_DEV_HPT366 is not set
+# CONFIG_BLK_DEV_JMICRON is not set
+# CONFIG_BLK_DEV_SC1200 is not set
+# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT8213 is not set
+# CONFIG_BLK_DEV_IT821X is not set
+# CONFIG_BLK_DEV_NS87415 is not set
+# CONFIG_BLK_DEV_PDC202XX_OLD is not set
+# CONFIG_BLK_DEV_PDC202XX_NEW is not set
+# CONFIG_BLK_DEV_SVWKS is not set
+# CONFIG_BLK_DEV_SIIMAGE is not set
+# CONFIG_BLK_DEV_SL82C105 is not set
+# CONFIG_BLK_DEV_SLC90E66 is not set
+# CONFIG_BLK_DEV_TRM290 is not set
+# CONFIG_BLK_DEV_VIA82CXXX is not set
+# CONFIG_BLK_DEV_TC86C001 is not set
# CONFIG_IDE_ARM is not set
# CONFIG_BLK_DEV_IDEDMA is not set
+CONFIG_IDE_ARCH_OBSOLETE_INIT=y
# CONFIG_BLK_DEV_HD is not set
#
@@ -457,10 +497,6 @@ CONFIG_IDE_PROC_FS=y
# CONFIG_SCSI_NETLINK is not set
# CONFIG_ATA is not set
# CONFIG_MD is not set
-
-#
-# Fusion MPT device support
-#
# CONFIG_FUSION is not set
#
@@ -479,6 +515,7 @@ CONFIG_NETDEVICES=y
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=y
+# CONFIG_VETH is not set
# CONFIG_ARCNET is not set
CONFIG_PHYLIB=y
@@ -504,20 +541,28 @@ CONFIG_MII=y
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
# CONFIG_NET_PCI is not set
+# CONFIG_B44 is not set
CONFIG_FS_ENET=y
# CONFIG_FS_ENET_HAS_SCC is not set
CONFIG_FS_ENET_HAS_FCC=y
+CONFIG_FS_ENET_MDIO_FCC=y
CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
+# CONFIG_E1000E is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
+# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
@@ -525,11 +570,14 @@ CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
+# CONFIG_IXGBE is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
+# CONFIG_NIU is not set
# CONFIG_MLX4_CORE is not set
+# CONFIG_TEHUTI is not set
# CONFIG_TR is not set
#
@@ -567,7 +615,6 @@ CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
@@ -638,14 +685,11 @@ CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_IPMI_HANDLER is not set
-# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
# CONFIG_NVRAM is not set
# CONFIG_GEN_RTC is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
-# CONFIG_AGP is not set
-# CONFIG_DRM is not set
# CONFIG_RAW_DRIVER is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
@@ -658,6 +702,13 @@ CONFIG_DEVPORT=y
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
#
# Multifunction device drivers
@@ -674,16 +725,17 @@ CONFIG_DAB=y
#
# Graphics support
#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=y
+# CONFIG_FB is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
-# CONFIG_VGASTATE is not set
-CONFIG_VIDEO_OUTPUT_CONTROL=y
-# CONFIG_FB is not set
-# CONFIG_FB_IBM_GXT4500 is not set
#
# Sound
@@ -707,6 +759,7 @@ CONFIG_USB_GADGET=y
# CONFIG_USB_GADGET_DEBUG_FILES is not set
CONFIG_USB_GADGET_SELECTED=y
# CONFIG_USB_GADGET_AMD5536UDC is not set
+# CONFIG_USB_GADGET_ATMEL_USBA is not set
# CONFIG_USB_GADGET_FSL_USB2 is not set
# CONFIG_USB_GADGET_NET2280 is not set
# CONFIG_USB_GADGET_PXA2XX is not set
@@ -731,19 +784,6 @@ CONFIG_USB_ETH=y
# CONFIG_RTC_CLASS is not set
#
-# DMA Engine support
-#
-# CONFIG_DMA_ENGINE is not set
-
-#
-# DMA Clients
-#
-
-#
-# DMA Devices
-#
-
-#
# Userspace I/O
#
# CONFIG_UIO is not set
@@ -759,7 +799,6 @@ CONFIG_EXT3_FS_XATTR=y
# CONFIG_EXT3_FS_POSIX_ACL is not set
# CONFIG_EXT3_FS_SECURITY is not set
CONFIG_JBD=y
-# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
@@ -799,7 +838,6 @@ CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
-CONFIG_RAMFS=y
#
# Miscellaneous filesystems
@@ -812,10 +850,7 @@ CONFIG_CRAMFS=y
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
+CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
@@ -853,10 +888,6 @@ CONFIG_MSDOS_PARTITION=y
# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
# CONFIG_SYSV68_PARTITION is not set
-
-#
-# Native Language Support
-#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
@@ -915,11 +946,15 @@ CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_INSTRUMENTATION=y
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
@@ -943,8 +978,11 @@ CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_PAGEALLOC is not set
@@ -952,16 +990,6 @@ CONFIG_FORCED_INLINING=y
# CONFIG_KGDB_CONSOLE is not set
CONFIG_BDI_SWITCH=y
# CONFIG_PPC_EARLY_DEBUG is not set
-# CONFIG_PPC_EARLY_DEBUG_LPAR is not set
-# CONFIG_PPC_EARLY_DEBUG_G5 is not set
-# CONFIG_PPC_EARLY_DEBUG_RTAS_PANEL is not set
-# CONFIG_PPC_EARLY_DEBUG_RTAS_CONSOLE is not set
-# CONFIG_PPC_EARLY_DEBUG_MAPLE is not set
-# CONFIG_PPC_EARLY_DEBUG_ISERIES is not set
-# CONFIG_PPC_EARLY_DEBUG_PAS_REALMODE is not set
-# CONFIG_PPC_EARLY_DEBUG_BEAT is not set
-# CONFIG_PPC_EARLY_DEBUG_44x is not set
-# CONFIG_PPC_EARLY_DEBUG_CPM is not set
#
# Security options
@@ -997,8 +1025,12 @@ CONFIG_CRYPTO_DES=y
# CONFIG_CRYPTO_ARC4 is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_SEED is not set
# CONFIG_CRYPTO_DEFLATE is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_AUTHENC is not set
CONFIG_CRYPTO_HW=y
+# CONFIG_PPC_CLOCK is not set
+CONFIG_PPC_LIB_RHEAP=y
--
1.5.3.4
^ permalink raw reply related
* Re: [PATCH 1/5] PowerPC 74xx: Katana Qp device tree
From: Mark A. Greer @ 2007-12-10 17:17 UTC (permalink / raw)
To: Mark A. Greer, David Gibson, Andrei Dolnikov, linuxppc-dev
In-Reply-To: <20071208013309.GB8662@localhost.localdomain>
On Sat, Dec 08, 2007 at 12:33:09PM +1100, David Gibson wrote:
> On Thu, Dec 06, 2007 at 04:27:56PM -0700, Mark A. Greer wrote:
> > David, et. al.,
> >
> > This is a big blob patch of what I've changed for the prpmc2800. It
> > includes the necessary changes in the kernel which you can probably
> > ignore but they're there for reference. If you like the dts, then I'll
> > split the blob up into logical pieces and Andrei can make similar
> > changes for the Katana Qp.
> >
> > Let me know what you think.
>
> Looks pretty reasonable. I would have preferred that labels be
> uppercase by convention, to make them easier to pick out by eyeball,
> but I think that's a lost cause at this stage.
I can do that. Thanks for the feedback. I'll break the blob up into
pieces and submit with the labels in uppercase.
Thanks,
Mark
^ permalink raw reply
* Re: [PATCH] windfarm: add PowerMac 12,1 support
From: Étienne Bersac @ 2007-12-10 17:17 UTC (permalink / raw)
To: Arnd Bergmann; +Cc: linuxppc-dev
In-Reply-To: <200712101639.52599.arnd@arndb.de>
Hi,
Thanks for reviewing the patch. I fix most of your comment excepts some
thing which i think are not mine. This is about the global variable. I
wrote this driver willing to be as more consistent with existing
windfarm_pm* drivers. All uses DBG(), global variable, etc. You'll see
that i dropped DBG in favor to pr_debug() ; thanks for pointing this.
windfarm drivers are plateform driver. This is why it uses global
variable, etc. This driver is never unloaded. (except for development
issues). Anyway, if Benjamin Herrenschmidt or Paul Mackerras tells to
use per module struct, i'll do so. The same goes for #ifdef MODULE.
That's just a copy paste from windfarm_pm81.c.
Appended the new patch, please review it.
Thanks,
Étienne.
Signed-off-by: Étienne Bersac <bersace03@laposte.net>
---
Implement fan control for PowerMac 12,1 machines. This needs update to
windfarm_lm75 and windfarm_max6690 sensors drivers in order to properly
match sensors by their location. The code is based on windfarm_pm81
driver, adapted to the complexity of PowerMac 12,1 : 4 system control
loops instead of one, per-control target correction and per-model
control rubber-banding.
All the data are copied from Darwin 8.10 AppleMacRISC4PE-185.0.0 module
as well as correction formula.
diff --git a/arch/powerpc/configs/g5_defconfig b/arch/powerpc/configs/g5_defconfig
index 3673dd2..4c048b3 100644
--- a/arch/powerpc/configs/g5_defconfig
+++ b/arch/powerpc/configs/g5_defconfig
@@ -667,6 +667,7 @@ CONFIG_WINDFARM=y
CONFIG_WINDFARM_PM81=y
CONFIG_WINDFARM_PM91=y
CONFIG_WINDFARM_PM112=y
+CONFIG_WINDFARM_PM121=y
# CONFIG_PMAC_RACKMETER is not set
CONFIG_NETDEVICES=y
# CONFIG_NETDEVICES_MULTIQUEUE is not set
diff --git a/drivers/macintosh/Kconfig b/drivers/macintosh/Kconfig
index 77f50b6..2d028e6 100644
--- a/drivers/macintosh/Kconfig
+++ b/drivers/macintosh/Kconfig
@@ -234,6 +234,14 @@ config WINDFARM_PM112
which are the recent dual and quad G5 machines using the
970MP dual-core processor.
+config WINDFARM_PM121
+ tristate "Support for thermal management on PowerMac12,1"
+ depends on WINDFARM && I2C && PMAC_SMU
+ select I2C_POWERMAC
+ help
+ This driver provides thermal control for the PowerMac12,1
+ which is the iMac G5 (iSight) 970MP
+
config ANSLCD
tristate "Support for ANS LCD display"
depends on ADB_CUDA && PPC_PMAC
diff --git a/drivers/macintosh/Makefile b/drivers/macintosh/Makefile
index 2dfc3f4..e3132ef 100644
--- a/drivers/macintosh/Makefile
+++ b/drivers/macintosh/Makefile
@@ -42,4 +42,9 @@ obj-$(CONFIG_WINDFARM_PM112) += windfarm_pm112.o windfarm_smu_sat.o \
windfarm_smu_sensors.o \
windfarm_max6690_sensor.o \
windfarm_lm75_sensor.o windfarm_pid.o
+obj-$(CONFIG_WINDFARM_PM121) += windfarm_pm121.o windfarm_smu_sat.o \
+ windfarm_smu_controls.o \
+ windfarm_smu_sensors.o \
+ windfarm_max6690_sensor.o \
+ windfarm_lm75_sensor.o windfarm_pid.o
obj-$(CONFIG_PMAC_RACKMETER) += rack-meter.o
diff --git a/drivers/macintosh/windfarm_lm75_sensor.c b/drivers/macintosh/windfarm_lm75_sensor.c
index 7e10c3a..b92b959 100644
--- a/drivers/macintosh/windfarm_lm75_sensor.c
+++ b/drivers/macintosh/windfarm_lm75_sensor.c
@@ -127,6 +127,12 @@ static struct wf_lm75_sensor *wf_lm75_create(struct i2c_adapter *adapter,
*/
if (!strcmp(loc, "Hard drive") || !strcmp(loc, "DRIVE BAY"))
lm->sens.name = "hd-temp";
+ else if (!strcmp(loc, "Incoming Air Temp"))
+ lm->sens.name = "incoming-air-temp";
+ else if (!strcmp(loc, "ODD Temp"))
+ lm->sens.name = "optical-drive-temp";
+ else if (!strcmp(loc, "HD Temp"))
+ lm->sens.name = "hard-drive-temp";
else
goto fail;
diff --git a/drivers/macintosh/windfarm_max6690_sensor.c b/drivers/macintosh/windfarm_max6690_sensor.c
index 5f03aab..e207a90 100644
--- a/drivers/macintosh/windfarm_max6690_sensor.c
+++ b/drivers/macintosh/windfarm_max6690_sensor.c
@@ -77,18 +77,28 @@ static struct wf_sensor_ops wf_max6690_ops = {
.owner = THIS_MODULE,
};
-static void wf_max6690_create(struct i2c_adapter *adapter, u8 addr)
+static void wf_max6690_create(struct i2c_adapter *adapter, u8 addr,
+ const char *loc)
{
struct wf_6690_sensor *max;
- char *name = "backside-temp";
+ char *name;
max = kzalloc(sizeof(struct wf_6690_sensor), GFP_KERNEL);
if (max == NULL) {
printk(KERN_ERR "windfarm: Couldn't create MAX6690 sensor %s: "
- "no memory\n", name);
+ "no memory\n", loc);
return;
}
+ if (!strcmp(loc, "BACKSIDE"))
+ name = "backside-temp";
+ else if (!strcmp(loc, "NB Ambient"))
+ name = "north-bridge-temp";
+ else if (!strcmp(loc, "GPU Ambient"))
+ name = "gpu-temp";
+ else
+ goto fail;
+
max->sens.ops = &wf_max6690_ops;
max->sens.name = name;
max->i2c.addr = addr >> 1;
@@ -138,9 +148,7 @@ static int wf_max6690_attach(struct i2c_adapter *adapter)
if (loc == NULL || addr == 0)
continue;
printk("found max6690, loc=%s addr=0x%02x\n", loc, addr);
- if (strcmp(loc, "BACKSIDE"))
- continue;
- wf_max6690_create(adapter, addr);
+ wf_max6690_create(adapter, addr, loc);
}
return 0;
diff --git a/drivers/macintosh/windfarm_pm121.c b/drivers/macintosh/windfarm_pm121.c
new file mode 100644
index 0000000..6898a09
--- /dev/null
+++ b/drivers/macintosh/windfarm_pm121.c
@@ -0,0 +1,1041 @@
+/*
+ * Windfarm PowerMac thermal control. iMac G5 iSight
+ *
+ * (c) Copyright 2007 Étienne Bersac <bersace@gmail.com>
+ *
+ * Bits & pieces from windfarm_pm81.c by (c) Copyright 2005 Benjamin
+ * Herrenschmidt, IBM Corp. <benh@kernel.crashing.org>
+ *
+ * Released under the term of the GNU GPL v2.
+ *
+ *
+ *
+ * PowerMac12,1
+ * ============
+ *
+ *
+ * The algorithm used is the PID control algorithm, used the same way
+ * the published Darwin code does, using the same values that are
+ * present in the Darwin 8.10 snapshot property lists (note however
+ * that none of the code has been re-used, it's a complete
+ * re-implementation
+ *
+ * There is two models using PowerMac12,1. Model 2 is iMac G5 iSight
+ * 17" while Model 3 is iMac G5 20". They do have both the same
+ * controls with a tiny difference. The control-ids of hard-drive-fan
+ * and cpu-fan is swapped.
+ *
+ *
+ * Target Correction :
+ *
+ * controls have a target correction calculated as :
+ *
+ * new_min = ((((average_power * slope) >> 16) + offset) >> 16) + min_value
+ * new_value = max(new_value, max(new_min, 0))
+ *
+ * OD Fan control correction.
+ *
+ * # model_id: 2
+ * offset : -19563152
+ * slope : 1956315
+ *
+ * # model_id: 3
+ * offset : -15650652
+ * slope : 1565065
+ *
+ * HD Fan control correction.
+ *
+ * # model_id: 2
+ * offset : -15650652
+ * slope : 1565065
+ *
+ * # model_id: 3
+ * offset : -19563152
+ * slope : 1956315
+ *
+ * CPU Fan control correction.
+ *
+ * # model_id: 2
+ * offset : -25431900
+ * slope : 2543190
+ *
+ * # model_id: 3
+ * offset : -15650652
+ * slope : 1565065
+ *
+ *
+ * Target rubber-banding :
+ *
+ * Some controls have a target correction which depends on another
+ * control value. The correction is computed in the following way :
+ *
+ * new_min = ref_value * slope + offset
+ *
+ * ref_value is the value of the reference control. If new_min is
+ * greater than 0, then we correct the target value using :
+ *
+ * new_target = max (new_target, new_min >> 16)
+ *
+ *
+ * # model_id : 2
+ * control : cpu-fan
+ * ref : optical-drive-fan
+ * offset : -15650652
+ * slope : 1565065
+ *
+ * # model_id : 3
+ * control : optical-drive-fan
+ * ref : hard-drive-fan
+ * offset : -32768000
+ * slope : 65536
+ *
+ *
+ * In order to have the moste efficient correction with those
+ * dependencies, we must trigger HD loop before OD loop before CPU
+ * loop.
+ *
+ *
+ * The various control loops found in Darwin config file are:
+ *
+ * HD Fan control loop.
+ *
+ * # model_id: 2
+ * control : hard-drive-fan
+ * sensor : hard-drive-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x002D70A3
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x370000
+ * Interval = 5s
+ *
+ * # model_id: 3
+ * control : hard-drive-fan
+ * sensor : hard-drive-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x002170A3
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x370000
+ * Interval = 5s
+ *
+ * OD Fan control loop.
+ *
+ * # model_id: 2
+ * control : optical-drive-fan
+ * sensor : optical-drive-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x001FAE14
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x320000
+ * Interval = 5s
+ *
+ * # model_id: 3
+ * control : optical-drive-fan
+ * sensor : optical-drive-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x001FAE14
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x320000
+ * Interval = 5s
+ *
+ * GPU Fan control loop.
+ *
+ * # model_id: 2
+ * control : hard-drive-fan
+ * sensor : gpu-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x002A6666
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x5A0000
+ * Interval = 5s
+ *
+ * # model_id: 3
+ * control : cpu-fan
+ * sensor : gpu-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x0010CCCC
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x500000
+ * Interval = 5s
+ *
+ * KODIAK (aka northbridge) Fan control loop.
+ *
+ * # model_id: 2
+ * control : optical-drive-fan
+ * sensor : north-bridge-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x003BD70A
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x550000
+ * Interval = 5s
+ *
+ * # model_id: 3
+ * control : hard-drive-fan
+ * sensor : north-bridge-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x0030F5C2
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x550000
+ * Interval = 5s
+ *
+ * CPU Fan control loop.
+ *
+ * control : cpu-fan
+ * sensors : cpu-temp, cpu-power
+ * PID params : from SDB partition
+ *
+ *
+ * CPU Slew control loop.
+ *
+ * control : cpufreq-clamp
+ * sensor : cpu-temp
+ *
+ */
+
+#undef DEBUG
+
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/init.h>
+#include <linux/spinlock.h>
+#include <linux/wait.h>
+#include <linux/kmod.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <asm/prom.h>
+#include <asm/machdep.h>
+#include <asm/io.h>
+#include <asm/system.h>
+#include <asm/sections.h>
+#include <asm/smu.h>
+
+#include "windfarm.h"
+#include "windfarm_pid.h"
+
+#define VERSION "0.3"
+
+static int pm121_mach_model; /* machine model id */
+
+/* Controls & sensors */
+static struct wf_sensor *sensor_cpu_power;
+static struct wf_sensor *sensor_cpu_temp;
+static struct wf_sensor *sensor_cpu_voltage;
+static struct wf_sensor *sensor_cpu_current;
+static struct wf_sensor *sensor_gpu_temp;
+static struct wf_sensor *sensor_north_bridge_temp;
+static struct wf_sensor *sensor_hard_drive_temp;
+static struct wf_sensor *sensor_optical_drive_temp;
+static struct wf_sensor *sensor_incoming_air_temp; /* unused ! */
+
+enum {
+ FAN_CPU,
+ FAN_HD,
+ FAN_OD,
+ CPUFREQ,
+ N_CONTROLS
+};
+static struct wf_control *controls[N_CONTROLS] = {};
+
+/* Set to kick the control loop into life */
+static int pm121_all_controls_ok, pm121_all_sensors_ok, pm121_started;
+
+enum {
+ FAILURE_FAN = 1 << 0,
+ FAILURE_SENSOR = 1 << 1,
+ FAILURE_OVERTEMP = 1 << 2
+};
+
+/* All sys loops. Note the HD before the OD loop in order to have it
+ run before. */
+enum {
+ LOOP_GPU, /* control = hd or cpu, but luckily,
+ it doesn't matter */
+ LOOP_HD, /* control = hd */
+ LOOP_KODIAK, /* control = hd or od */
+ LOOP_OD, /* control = od */
+ N_LOOPS
+};
+
+static const char *loop_names[N_LOOPS] = {
+ "GPU",
+ "HD",
+ "KODIAK",
+ "OD",
+};
+
+#define PM121_NUM_CONFIGS 2
+
+static unsigned int pm121_failure_state;
+static int pm121_readjust, pm121_skipping;
+static s32 average_power;
+
+struct pm121_correction {
+ int offset;
+ int slope;
+};
+
+static const struct pm121_correction
+corrections[N_CONTROLS][PM121_NUM_CONFIGS] = {
+ /* FAN_OD */
+ {
+ /* MODEL 2 */
+ { .offset = -19563152,
+ .slope = 1956315
+ },
+ /* MODEL 3 */
+ { .offset = -15650652,
+ .slope = 1565065
+ },
+ },
+ /* FAN_HD */
+ {
+ /* MODEL 2 */
+ { .offset = -15650652,
+ .slope = 1565065
+ },
+ /* MODEL 3 */
+ { .offset = -19563152,
+ .slope = 1956315
+ },
+ },
+ /* FAN_CPU */
+ {
+ /* MODEL 2 */
+ { .offset = -25431900,
+ .slope = 2543190
+ },
+ /* MODEL 3 */
+ { .offset = -15650652,
+ .slope = 1565065
+ },
+ },
+ /* CPUFREQ has no correction (and is not implemented at all) */
+};
+
+struct pm121_connection {
+ unsigned int control_id;
+ unsigned int ref_id;
+ struct pm121_correction correction;
+};
+
+static const struct pm121_connection pm121_connections[] = {
+ /* MODEL 2 */
+ { .control_id = FAN_CPU,
+ .ref_id = FAN_OD,
+ { .offset = -32768000,
+ .slope = 65536
+ }
+ },
+ /* MODEL 3 */
+ { .control_id = FAN_OD,
+ .ref_id = FAN_HD,
+ { .offset = -32768000,
+ .slope = 65536
+ }
+ },
+};
+
+/* pointer to the current model connection */
+static const struct pm121_connection *pm121_connection;
+
+/*
+ * ****** System Fans Control Loop ******
+ *
+ */
+
+/* Since each loop handles only one control and we want to avoid
+ * writing virtual control, we store the control correction with the
+ * loop params. Some data are not set, there are common to all loop
+ * and thus, hardcoded.
+ */
+struct pm121_sys_param {
+ /* purely informative since we use mach_model-2 as index */
+ int model_id;
+ struct wf_sensor **sensor; /* use sensor_id instead ? */
+ s32 gp, itarget;
+ unsigned int control_id;
+};
+
+static const struct pm121_sys_param
+pm121_sys_all_params[N_LOOPS][PM121_NUM_CONFIGS] = {
+ /* GPU Fan control loop */
+ {
+ { .model_id = 2,
+ .sensor = &sensor_gpu_temp,
+ .gp = 0x002A6666,
+ .itarget = 0x5A0000,
+ .control_id = FAN_HD,
+ },
+ { .model_id = 3,
+ .sensor = &sensor_gpu_temp,
+ .gp = 0x0010CCCC,
+ .itarget = 0x500000,
+ .control_id = FAN_CPU,
+ },
+ },
+ /* HD Fan control loop */
+ {
+ { .model_id = 2,
+ .sensor = &sensor_hard_drive_temp,
+ .gp = 0x002D70A3,
+ .itarget = 0x370000,
+ .control_id = FAN_HD,
+ },
+ { .model_id = 3,
+ .sensor = &sensor_hard_drive_temp,
+ .gp = 0x002170A3,
+ .itarget = 0x370000,
+ .control_id = FAN_HD,
+ },
+ },
+ /* KODIAK Fan control loop */
+ {
+ { .model_id = 2,
+ .sensor = &sensor_north_bridge_temp,
+ .gp = 0x003BD70A,
+ .itarget = 0x550000,
+ .control_id = FAN_OD,
+ },
+ { .model_id = 3,
+ .sensor = &sensor_north_bridge_temp,
+ .gp = 0x0030F5C2,
+ .itarget = 0x550000,
+ .control_id = FAN_HD,
+ },
+ },
+ /* OD Fan control loop */
+ {
+ { .model_id = 2,
+ .sensor = &sensor_optical_drive_temp,
+ .gp = 0x001FAE14,
+ .itarget = 0x320000,
+ .control_id = FAN_OD,
+ },
+ { .model_id = 3,
+ .sensor = &sensor_optical_drive_temp,
+ .gp = 0x001FAE14,
+ .itarget = 0x320000,
+ .control_id = FAN_OD,
+ },
+ },
+};
+
+/* the hardcoded values */
+#define PM121_SYS_GD 0x00000000
+#define PM121_SYS_GR 0x00019999
+#define PM121_SYS_HISTORY_SIZE 2
+#define PM121_SYS_INTERVAL 5
+
+/* State data used by the system fans control loop
+ */
+struct pm121_sys_state {
+ int ticks;
+ s32 setpoint;
+ struct wf_pid_state pid;
+};
+
+struct pm121_sys_state *pm121_sys_state[N_LOOPS] = {};
+
+/*
+ * ****** CPU Fans Control Loop ******
+ *
+ */
+
+#define PM121_CPU_INTERVAL 1
+
+/* State data used by the cpu fans control loop
+ */
+struct pm121_cpu_state {
+ int ticks;
+ s32 setpoint;
+ struct wf_cpu_pid_state pid;
+};
+
+static struct pm121_cpu_state *pm121_cpu_state;
+
+
+
+/*
+ * ***** Implementation *****
+ *
+ */
+
+/* correction the value using the output-low-bound correction algo */
+static s32 pm121_correct(s32 new_setpoint,
+ unsigned int control_id,
+ s32 min)
+{
+ s32 new_min;
+ struct pm121_correction *correction;
+ correction = &corrections[control_id][pm121_mach_model - 2];
+
+ new_min = (average_power * correction->slope) >> 16;
+ new_min += correction->offset;
+ new_min = (new_min >> 16) + min;
+
+ return max(new_setpoint, max(new_min, 0));
+}
+
+static s32 pm121_connect(unsigned int control_id, s32 setpoint)
+{
+ s32 new_min, value, new_setpoint;
+
+ if (pm121_connection->control_id == control_id) {
+ controls[control_id]->ops->get_value(controls[control_id],
+ &value);
+ new_min = value * pm121_connection->correction.slope;
+ new_min += pm121_connection->correction.offset;
+ if (new_min > 0) {
+ new_setpoint = max(setpoint, (new_min >> 16));
+ if (new_setpoint != setpoint) {
+ pr_debug("pm121: %s depending on %s, "
+ "corrected from %d to %d RPM\n",
+ controls[control_id]->name,
+ controls[pm121_connection->ref_id]->name,
+ (int) setpoint, (int) new_setpoint);
+ }
+ } else
+ new_setpoint = setpoint;
+ }
+ /* no connection */
+ else
+ new_setpoint = setpoint;
+
+ return new_setpoint;
+}
+
+/* FAN LOOPS */
+static void pm121_create_sys_fans(int loop_id)
+{
+ struct pm121_sys_param *param = NULL;
+ struct wf_pid_param pid_param;
+ struct wf_control *control = NULL;
+ int i;
+
+ /* First, locate the params for this model */
+ for (i = 0; i < PM121_NUM_CONFIGS; i++) {
+ if (pm121_sys_all_params[loop_id][i].model_id == pm121_mach_model) {
+ param = &(pm121_sys_all_params[loop_id][i]);
+ break;
+ }
+ }
+
+ /* No params found, put fans to max */
+ if (param == NULL) {
+ printk(KERN_WARNING "pm121: %s fan config not found "
+ " for this machine model\n",
+ loop_names[loop_id]);
+ goto fail;
+ }
+
+ control = controls[param->control_id];
+
+ /* Alloc & initialize state */
+ pm121_sys_state[loop_id] = kmalloc(sizeof(struct pm121_sys_state),
+ GFP_KERNEL);
+ if (pm121_sys_state[loop_id] == NULL) {
+ printk(KERN_WARNING "pm121: Memory allocation error\n");
+ goto fail;
+ }
+ pm121_sys_state[loop_id]->ticks = 1;
+
+ /* Fill PID params */
+ pid_param.gd = PM121_SYS_GD;
+ pid_param.gp = param->gp;
+ pid_param.gr = PM121_SYS_GR;
+ pid_param.interval = PM121_SYS_INTERVAL;
+ pid_param.history_len = PM121_SYS_HISTORY_SIZE;
+ pid_param.itarget = param->itarget;
+ pid_param.min = control->ops->get_min(control);
+ pid_param.max = control->ops->get_max(control);
+
+ wf_pid_init(&pm121_sys_state[loop_id]->pid, &pid_param);
+
+ pr_debug("pm121: %s Fan control loop initialized.\n"
+ " itarged=%d.%03d, min=%d RPM, max=%d RPM\n",
+ loop_names[loop_id], FIX32TOPRINT(pid_param.itarget),
+ pid_param.min, pid_param.max);
+ return;
+
+ fail:
+ /* note that this is not optimal since another loop may still
+ control the same control */
+ printk(KERN_WARNING "pm121: failed to set up %s loop "
+ "setting \"%s\" to max speed.\n",
+ loop_names[loop_id], control->name);
+
+ if (control)
+ wf_control_set_max(control);
+}
+
+static void pm121_sys_fans_tick(int loop_id)
+{
+ struct pm121_sys_param *param;
+ struct pm121_sys_state *st;
+ struct wf_sensor *sensor;
+ struct wf_control *control;
+ s32 temp, new_setpoint;
+ int rc;
+
+ param = &(pm121_sys_all_params[loop_id][pm121_mach_model-2]);
+ st = pm121_sys_state[loop_id];
+ sensor = *(param->sensor);
+ control = controls[param->control_id];
+
+ if (--st->ticks != 0) {
+ if (pm121_readjust)
+ goto readjust;
+ return;
+ }
+ st->ticks = PM121_SYS_INTERVAL;
+
+ rc = sensor->ops->get_value(sensor, &temp);
+ if (rc) {
+ printk(KERN_WARNING "windfarm: %s sensor error %d\n",
+ sensor->name, rc);
+ pm121_failure_state |= FAILURE_SENSOR;
+ return;
+ }
+
+ pr_debug("pm121: %s Fan tick ! %s: %d.%03d\n",
+ loop_names[loop_id], sensor->name,
+ FIX32TOPRINT(temp));
+
+ new_setpoint = wf_pid_run(&st->pid, temp);
+
+ /* correction */
+ new_setpoint = pm121_correct(new_setpoint,
+ param->control_id,
+ st->pid.param.min);
+ /* linked corretion */
+ new_setpoint = pm121_connect(param->control_id, new_setpoint);
+
+ if (new_setpoint == st->setpoint)
+ return;
+ st->setpoint = new_setpoint;
+ pr_debug("pm121: %s corrected setpoint: %d RPM\n",
+ control->name, (int)new_setpoint);
+ readjust:
+ if (control && pm121_failure_state == 0) {
+ rc = control->ops->set_value(control, st->setpoint);
+ if (rc) {
+ printk(KERN_WARNING "windfarm: %s fan error %d\n",
+ control->name, rc);
+ pm121_failure_state |= FAILURE_FAN;
+ }
+ }
+}
+
+
+/* CPU LOOP */
+static void pm121_create_cpu_fans(void)
+{
+ struct wf_cpu_pid_param pid_param;
+ const struct smu_sdbp_header *hdr;
+ struct smu_sdbp_cpupiddata *piddata;
+ struct smu_sdbp_fvt *fvt;
+ struct wf_control *fan_cpu;
+ s32 tmax, tdelta, maxpow, powadj;
+
+ fan_cpu = controls[FAN_CPU];
+
+ /* First, locate the PID params in SMU SBD */
+ hdr = smu_get_sdb_partition(SMU_SDB_CPUPIDDATA_ID, NULL);
+ if (hdr == 0) {
+ printk(KERN_WARNING "pm121: CPU PID fan config not found.\n");
+ goto fail;
+ }
+ piddata = (struct smu_sdbp_cpupiddata *)&hdr[1];
+
+ /* Get the FVT params for operating point 0 (the only supported one
+ * for now) in order to get tmax
+ */
+ hdr = smu_get_sdb_partition(SMU_SDB_FVT_ID, NULL);
+ if (hdr) {
+ fvt = (struct smu_sdbp_fvt *)&hdr[1];
+ tmax = ((s32)fvt->maxtemp) << 16;
+ } else
+ tmax = 0x5e0000; /* 94 degree default */
+
+ /* Alloc & initialize state */
+ pm121_cpu_state = kmalloc(sizeof(struct pm121_cpu_state),
+ GFP_KERNEL);
+ if (pm121_cpu_state == NULL)
+ goto fail;
+ pm121_cpu_state->ticks = 1;
+
+ /* Fill PID params */
+ pid_param.interval = PM121_CPU_INTERVAL;
+ pid_param.history_len = piddata->history_len;
+ if (pid_param.history_len > WF_CPU_PID_MAX_HISTORY) {
+ printk(KERN_WARNING "pm121: History size overflow on "
+ "CPU control loop (%d)\n", piddata->history_len);
+ pid_param.history_len = WF_CPU_PID_MAX_HISTORY;
+ }
+ pid_param.gd = piddata->gd;
+ pid_param.gp = piddata->gp;
+ pid_param.gr = piddata->gr / pid_param.history_len;
+
+ tdelta = ((s32)piddata->target_temp_delta) << 16;
+ maxpow = ((s32)piddata->max_power) << 16;
+ powadj = ((s32)piddata->power_adj) << 16;
+
+ pid_param.tmax = tmax;
+ pid_param.ttarget = tmax - tdelta;
+ pid_param.pmaxadj = maxpow - powadj;
+
+ pid_param.min = fan_cpu->ops->get_min(fan_cpu);
+ pid_param.max = fan_cpu->ops->get_max(fan_cpu);
+
+ wf_cpu_pid_init(&pm121_cpu_state->pid, &pid_param);
+
+ pr_debug("pm121: CPU Fan control initialized.\n");
+ pr_debug(" ttarged=%d.%03d, tmax=%d.%03d, min=%d RPM, max=%d RPM,\n",
+ FIX32TOPRINT(pid_param.ttarget), FIX32TOPRINT(pid_param.tmax),
+ pid_param.min, pid_param.max);
+
+ return;
+
+ fail:
+ printk(KERN_WARNING "pm121: CPU fan config not found, max fan speed\n");
+
+ if (controls[CPUFREQ])
+ wf_control_set_max(controls[CPUFREQ]);
+ if (fan_cpu)
+ wf_control_set_max(fan_cpu);
+}
+
+
+static void pm121_cpu_fans_tick(struct pm121_cpu_state *st)
+{
+ s32 new_setpoint, temp, power;
+ struct wf_control *fan_cpu = NULL;
+ int rc;
+
+ if (--st->ticks != 0) {
+ if (pm121_readjust)
+ goto readjust;
+ return;
+ }
+ st->ticks = PM121_CPU_INTERVAL;
+
+ fan_cpu = controls[FAN_CPU];
+
+ rc = sensor_cpu_temp->ops->get_value(sensor_cpu_temp, &temp);
+ if (rc) {
+ printk(KERN_WARNING "pm121: CPU temp sensor error %d\n",
+ rc);
+ pm121_failure_state |= FAILURE_SENSOR;
+ return;
+ }
+
+ rc = sensor_cpu_power->ops->get_value(sensor_cpu_power, &power);
+ if (rc) {
+ printk(KERN_WARNING "pm121: CPU power sensor error %d\n",
+ rc);
+ pm121_failure_state |= FAILURE_SENSOR;
+ return;
+ }
+
+ pr_debug("pm121: CPU Fans tick ! CPU temp: %d.%03d°C, power: %d.%03d\n",
+ FIX32TOPRINT(temp), FIX32TOPRINT(power));
+
+ if (temp > st->pid.param.tmax)
+ pm121_failure_state |= FAILURE_OVERTEMP;
+
+ new_setpoint = wf_cpu_pid_run(&st->pid, power, temp);
+
+ /* correction */
+ new_setpoint = pm121_correct(new_setpoint,
+ FAN_CPU,
+ st->pid.param.min);
+
+ /* connected correction */
+ new_setpoint = pm121_connect(FAN_CPU, new_setpoint);
+
+ if (st->setpoint == new_setpoint)
+ return;
+ st->setpoint = new_setpoint;
+ pr_debug("pm121: CPU corrected setpoint: %d RPM\n", (int)new_setpoint);
+
+ readjust:
+ if (fan_cpu && pm121_failure_state == 0) {
+ rc = fan_cpu->ops->set_value(fan_cpu, st->setpoint);
+ if (rc) {
+ printk(KERN_WARNING "pm121: %s fan error %d\n",
+ fan_cpu->name, rc);
+ pm121_failure_state |= FAILURE_FAN;
+ }
+ }
+}
+
+/*
+ * ****** Common ******
+ *
+ */
+
+static void pm121_tick(void)
+{
+ unsigned int last_failure = pm121_failure_state;
+ unsigned int new_failure;
+ s32 total_power;
+ int i;
+
+ if (!pm121_started) {
+ pr_debug("pm121: creating control loops !\n");
+ for (i = 0; i < N_LOOPS; i++)
+ pm121_create_sys_fans(i);
+
+ pm121_create_cpu_fans();
+ pm121_started = 1;
+ }
+
+ /* skipping ticks */
+ if (pm121_skipping && --pm121_skipping)
+ return;
+
+ /* compute average power */
+ total_power = 0;
+ for (i = 0; i < pm121_cpu_state->pid.param.history_len; i++)
+ total_power += pm121_cpu_state->pid.powers[i];
+
+ average_power = total_power / pm121_cpu_state->pid.param.history_len;
+
+
+ pm121_failure_state = 0;
+ for (i = 0 ; i < N_LOOPS; i++) {
+ if (pm121_sys_state[i])
+ pm121_sys_fans_tick(i);
+ }
+
+ if (pm121_cpu_state)
+ pm121_cpu_fans_tick(pm121_cpu_state);
+
+ pm121_readjust = 0;
+ new_failure = pm121_failure_state & ~last_failure;
+
+ /* If entering failure mode, clamp cpufreq and ramp all
+ * fans to full speed.
+ */
+ if (pm121_failure_state && !last_failure) {
+ for (i = 0; i < N_CONTROLS; i++) {
+ if (controls[i])
+ wf_control_set_max(controls[i]);
+ }
+ }
+
+ /* If leaving failure mode, unclamp cpufreq and readjust
+ * all fans on next iteration
+ */
+ if (!pm121_failure_state && last_failure) {
+ if (controls[CPUFREQ])
+ wf_control_set_min(controls[CPUFREQ]);
+ pm121_readjust = 1;
+ }
+
+ /* Overtemp condition detected, notify and start skipping a couple
+ * ticks to let the temperature go down
+ */
+ if (new_failure & FAILURE_OVERTEMP) {
+ wf_set_overtemp();
+ pm121_skipping = 2;
+ }
+
+ /* We only clear the overtemp condition if overtemp is cleared
+ * _and_ no other failure is present. Since a sensor error will
+ * clear the overtemp condition (can't measure temperature) at
+ * the control loop levels, but we don't want to keep it clear
+ * here in this case
+ */
+ if (new_failure == 0 && last_failure & FAILURE_OVERTEMP)
+ wf_clear_overtemp();
+}
+
+
+static struct wf_control* pm121_register_control(struct wf_control *ct,
+ const char *match,
+ unsigned int id)
+{
+ if (controls[id] == NULL && !strcmp(ct->name, match)) {
+ if (wf_get_control(ct) == 0)
+ controls[FAN_OD] = ct;
+ }
+ return controls[id];
+}
+
+static void pm121_new_control(struct wf_control *ct)
+{
+ int all = 1;
+
+ if (pm121_all_controls_ok)
+ return;
+
+ all = all && pm121_register_control(ct, "optical-driver-fan", FAN_OD);
+ all = all && pm121_register_control(ct, "hard-driver-fan", FAN_HD);
+ all = all && pm121_register_control(ct, "cpu-driver-fan", FAN_CPU);
+ all = all && pm121_register_control(ct, "cpufreq-clamp", CPUFREQ);
+
+ if (all)
+ pm121_all_controls_ok = 1;
+}
+
+
+
+
+static struct wf_sensor* pm121_register_sensor(struct wf_sensor *sensor,
+ const char *match,
+ struct wf_sensor **var)
+{
+ if (*var == NULL && !strcmp(sensor->name, match)) {
+ if (wf_get_sensor(sensor) == 0)
+ *var = sensor;
+ }
+ return *var;
+}
+
+static void pm121_new_sensor(struct wf_sensor *sr)
+{
+ int all = 1;
+
+ if (pm121_all_sensors_ok)
+ return;
+
+ all = all && pm121_register_sensor(sr, "cpu-temp",
+ &sensor_cpu_temp);
+ all = all && pm121_register_sensor(sr, "cpu-current",
+ &sensor_cpu_current);
+ all = all && pm121_register_sensor(sr, "cpu-voltage",
+ &sensor_cpu_voltage);
+ all = all && pm121_register_sensor(sr, "cpu-power",
+ &sensor_cpu_power);
+ all = all && pm121_register_sensor(sr, "hard-drive-temp",
+ &sensor_hard_drive_temp);
+ all = all && pm121_register_sensor(sr, "optical-drive-temp",
+ &sensor_optical_drive_temp);
+ all = all && pm121_register_sensor(sr, "incoming-air-temp",
+ &sensor_incoming_air_temp);
+ all = all && pm121_register_sensor(sr, "north-bridge-temp",
+ &sensor_north_bridge_temp);
+ all = all && pm121_register_sensor(sr, "gpu-temp",
+ &sensor_gpu_temp);
+
+ if (all)
+ pm121_all_sensors_ok = 1;
+}
+
+
+
+static int pm121_notify(struct notifier_block *self,
+ unsigned long event, void *data)
+{
+ switch (event) {
+ case WF_EVENT_NEW_CONTROL:
+ pr_debug("pm121: new control %s detected\n",
+ ((struct wf_control *)data)->name);
+ pm121_new_control(data);
+ break;
+ case WF_EVENT_NEW_SENSOR:
+ pr_debug("pm121: new sensor %s detected\n",
+ ((struct wf_sensor *)data)->name);
+ pm121_new_sensor(data);
+ break;
+ case WF_EVENT_TICK:
+ if (pm121_all_controls_ok && pm121_all_sensors_ok)
+ pm121_tick();
+ break;
+ }
+
+ return 0;
+}
+
+static struct notifier_block pm121_events = {
+ .notifier_call = pm121_notify,
+};
+
+static int pm121_init_pm(void)
+{
+ const struct smu_sdbp_header *hdr;
+
+ hdr = smu_get_sdb_partition(SMU_SDB_SENSORTREE_ID, NULL);
+ if (hdr != 0) {
+ struct smu_sdbp_sensortree *st =
+ (struct smu_sdbp_sensortree *)&hdr[1];
+ pm121_mach_model = st->model_id;
+ }
+
+ pm121_connection = &pm121_connections[pm121_mach_model - 2];
+
+ printk(KERN_INFO "pm121: Initializing for iMac G5 iSight model ID %d\n",
+ pm121_mach_model);
+
+ return 0;
+}
+
+
+static int pm121_probe(struct platform_device *ddev)
+{
+ wf_register_client(&pm121_events);
+
+ return 0;
+}
+
+static int __devexit pm121_remove(struct platform_device *ddev)
+{
+ wf_unregister_client(&pm121_events);
+ return 0;
+}
+
+static struct platform_driver pm121_driver = {
+ .probe = pm121_probe,
+ .remove = __devexit_p(pm121_remove),
+ .driver = {
+ .name = "windfarm",
+ .bus = &platform_bus_type,
+ },
+};
+
+
+static int __init pm121_init(void)
+{
+ int rc = -ENODEV;
+
+ if (machine_is_compatible("PowerMac12,1"))
+ rc = pm121_init_pm();
+
+ if (rc == 0) {
+ request_module("windfarm_smu_controls");
+ request_module("windfarm_smu_sensors");
+ request_module("windfarm_smu_sat");
+ request_module("windfarm_lm75_sensor");
+ request_module("windfarm_max6690_sensor");
+ request_module("windfarm_cpufreq_clamp");
+ platform_driver_register(&pm121_driver);
+ }
+
+ return rc;
+}
+
+static void __exit pm121_exit(void)
+{
+
+ platform_driver_unregister(&pm121_driver);
+}
+
+
+module_init(pm121_init);
+module_exit(pm121_exit);
+
+MODULE_AUTHOR("Étienne Bersac <bersace@gmail.com>");
+MODULE_DESCRIPTION("Thermal control logic for iMac G5 (iSight)");
+MODULE_LICENSE("GPL");
+
diff --git a/drivers/macintosh/windfarm_smu_controls.c b/drivers/macintosh/windfarm_smu_controls.c
index 58c2590..961fa0e 100644
--- a/drivers/macintosh/windfarm_smu_controls.c
+++ b/drivers/macintosh/windfarm_smu_controls.c
@@ -218,6 +218,10 @@ static struct smu_fan_control *smu_fan_create(struct device_node *node,
fct->ctrl.name = "cpu-fan";
else if (!strcmp(l, "Hard Drive") || !strcmp(l, "Hard drive"))
fct->ctrl.name = "drive-bay-fan";
+ else if (!strcmp(l, "HDD Fan")) /* seen on iMac G5 iSight */
+ fct->ctrl.name = "hard-drive-fan";
+ else if (!strcmp(l, "ODD Fan")) /* same */
+ fct->ctrl.name = "optical-drive-fan";
/* Unrecognized fan, bail out */
if (fct->ctrl.name == NULL)
^ permalink raw reply related
* Re: [i2c] [PATCH 0/4] Series to add device tree naming to i2c
From: Scott Wood @ 2007-12-10 16:42 UTC (permalink / raw)
To: Benjamin Herrenschmidt; +Cc: Jean Delvare, linuxppc-dev, i2c
In-Reply-To: <1197236326.6563.22.camel@pasglop>
On Mon, Dec 10, 2007 at 08:38:46AM +1100, Benjamin Herrenschmidt wrote:
> The more I think about it, the more I tend to agree that tagging isn't
> necessary and you are right. We should just match the name against the
> "compatible" property of the OF nodes (which mean we need to support
> multiple matches though since "compatible" is a list of strings).
It may not be strictly necessary, but I think it's a good idea not just for
safety reasons, but as an indication to the driver what additional
information it has access to. We could put a match data pointer in the i2c
device, and have it be a valid node pointer if the match was an OF one (and
a device-specific struct for a straight platform device, etc). This could
be useful if a device needs to have more properties than standard
address/type/interrupt for some reason.
-Scott
^ permalink raw reply
* Re: [PATCH] windfarm: add PowerMac 12,1 support
From: Étienne Bersac @ 2007-12-10 17:22 UTC (permalink / raw)
To: Arnd Bergmann; +Cc: linuxppc-dev
In-Reply-To: <1197307026.8825.7.camel@thilivren>
Hi,
Appended a patch which builds without warnings due to struct declared
const. Please review it.
Thanks,
Étienne
Signed-off-by: Étienne Bersac <bersace03@gmail.com>
---
Implement fan control for PowerMac 12,1 machines. This needs update to
windfarm_lm75 and windfarm_max6690 sensors drivers in order to properly
match sensors by their location. The code is based on windfarm_pm81
driver, adapted to the complexity of PowerMac 12,1 : 4 system control
loops instead of one, per-control target correction and per-model
control rubber-banding.
All the data are copied from Darwin 8.10 AppleMacRISC4PE-185.0.0 module
as well as correction formula.
diff --git a/arch/powerpc/configs/g5_defconfig b/arch/powerpc/configs/g5_defconfig
index 3673dd2..4c048b3 100644
--- a/arch/powerpc/configs/g5_defconfig
+++ b/arch/powerpc/configs/g5_defconfig
@@ -667,6 +667,7 @@ CONFIG_WINDFARM=y
CONFIG_WINDFARM_PM81=y
CONFIG_WINDFARM_PM91=y
CONFIG_WINDFARM_PM112=y
+CONFIG_WINDFARM_PM121=y
# CONFIG_PMAC_RACKMETER is not set
CONFIG_NETDEVICES=y
# CONFIG_NETDEVICES_MULTIQUEUE is not set
diff --git a/drivers/macintosh/Kconfig b/drivers/macintosh/Kconfig
index 77f50b6..2d028e6 100644
--- a/drivers/macintosh/Kconfig
+++ b/drivers/macintosh/Kconfig
@@ -234,6 +234,14 @@ config WINDFARM_PM112
which are the recent dual and quad G5 machines using the
970MP dual-core processor.
+config WINDFARM_PM121
+ tristate "Support for thermal management on PowerMac12,1"
+ depends on WINDFARM && I2C && PMAC_SMU
+ select I2C_POWERMAC
+ help
+ This driver provides thermal control for the PowerMac12,1
+ which is the iMac G5 (iSight) 970MP
+
config ANSLCD
tristate "Support for ANS LCD display"
depends on ADB_CUDA && PPC_PMAC
diff --git a/drivers/macintosh/Makefile b/drivers/macintosh/Makefile
index 2dfc3f4..e3132ef 100644
--- a/drivers/macintosh/Makefile
+++ b/drivers/macintosh/Makefile
@@ -42,4 +42,9 @@ obj-$(CONFIG_WINDFARM_PM112) += windfarm_pm112.o windfarm_smu_sat.o \
windfarm_smu_sensors.o \
windfarm_max6690_sensor.o \
windfarm_lm75_sensor.o windfarm_pid.o
+obj-$(CONFIG_WINDFARM_PM121) += windfarm_pm121.o windfarm_smu_sat.o \
+ windfarm_smu_controls.o \
+ windfarm_smu_sensors.o \
+ windfarm_max6690_sensor.o \
+ windfarm_lm75_sensor.o windfarm_pid.o
obj-$(CONFIG_PMAC_RACKMETER) += rack-meter.o
diff --git a/drivers/macintosh/windfarm_lm75_sensor.c b/drivers/macintosh/windfarm_lm75_sensor.c
index 7e10c3a..b92b959 100644
--- a/drivers/macintosh/windfarm_lm75_sensor.c
+++ b/drivers/macintosh/windfarm_lm75_sensor.c
@@ -127,6 +127,12 @@ static struct wf_lm75_sensor *wf_lm75_create(struct i2c_adapter *adapter,
*/
if (!strcmp(loc, "Hard drive") || !strcmp(loc, "DRIVE BAY"))
lm->sens.name = "hd-temp";
+ else if (!strcmp(loc, "Incoming Air Temp"))
+ lm->sens.name = "incoming-air-temp";
+ else if (!strcmp(loc, "ODD Temp"))
+ lm->sens.name = "optical-drive-temp";
+ else if (!strcmp(loc, "HD Temp"))
+ lm->sens.name = "hard-drive-temp";
else
goto fail;
diff --git a/drivers/macintosh/windfarm_max6690_sensor.c b/drivers/macintosh/windfarm_max6690_sensor.c
index 5f03aab..e207a90 100644
--- a/drivers/macintosh/windfarm_max6690_sensor.c
+++ b/drivers/macintosh/windfarm_max6690_sensor.c
@@ -77,18 +77,28 @@ static struct wf_sensor_ops wf_max6690_ops = {
.owner = THIS_MODULE,
};
-static void wf_max6690_create(struct i2c_adapter *adapter, u8 addr)
+static void wf_max6690_create(struct i2c_adapter *adapter, u8 addr,
+ const char *loc)
{
struct wf_6690_sensor *max;
- char *name = "backside-temp";
+ char *name;
max = kzalloc(sizeof(struct wf_6690_sensor), GFP_KERNEL);
if (max == NULL) {
printk(KERN_ERR "windfarm: Couldn't create MAX6690 sensor %s: "
- "no memory\n", name);
+ "no memory\n", loc);
return;
}
+ if (!strcmp(loc, "BACKSIDE"))
+ name = "backside-temp";
+ else if (!strcmp(loc, "NB Ambient"))
+ name = "north-bridge-temp";
+ else if (!strcmp(loc, "GPU Ambient"))
+ name = "gpu-temp";
+ else
+ goto fail;
+
max->sens.ops = &wf_max6690_ops;
max->sens.name = name;
max->i2c.addr = addr >> 1;
@@ -138,9 +148,7 @@ static int wf_max6690_attach(struct i2c_adapter *adapter)
if (loc == NULL || addr == 0)
continue;
printk("found max6690, loc=%s addr=0x%02x\n", loc, addr);
- if (strcmp(loc, "BACKSIDE"))
- continue;
- wf_max6690_create(adapter, addr);
+ wf_max6690_create(adapter, addr, loc);
}
return 0;
diff --git a/drivers/macintosh/windfarm_pm121.c b/drivers/macintosh/windfarm_pm121.c
new file mode 100644
index 0000000..5276156
--- /dev/null
+++ b/drivers/macintosh/windfarm_pm121.c
@@ -0,0 +1,1040 @@
+/*
+ * Windfarm PowerMac thermal control. iMac G5 iSight
+ *
+ * (c) Copyright 2007 Étienne Bersac <bersace@gmail.com>
+ *
+ * Bits & pieces from windfarm_pm81.c by (c) Copyright 2005 Benjamin
+ * Herrenschmidt, IBM Corp. <benh@kernel.crashing.org>
+ *
+ * Released under the term of the GNU GPL v2.
+ *
+ *
+ *
+ * PowerMac12,1
+ * ============
+ *
+ *
+ * The algorithm used is the PID control algorithm, used the same way
+ * the published Darwin code does, using the same values that are
+ * present in the Darwin 8.10 snapshot property lists (note however
+ * that none of the code has been re-used, it's a complete
+ * re-implementation
+ *
+ * There is two models using PowerMac12,1. Model 2 is iMac G5 iSight
+ * 17" while Model 3 is iMac G5 20". They do have both the same
+ * controls with a tiny difference. The control-ids of hard-drive-fan
+ * and cpu-fan is swapped.
+ *
+ *
+ * Target Correction :
+ *
+ * controls have a target correction calculated as :
+ *
+ * new_min = ((((average_power * slope) >> 16) + offset) >> 16) + min_value
+ * new_value = max(new_value, max(new_min, 0))
+ *
+ * OD Fan control correction.
+ *
+ * # model_id: 2
+ * offset : -19563152
+ * slope : 1956315
+ *
+ * # model_id: 3
+ * offset : -15650652
+ * slope : 1565065
+ *
+ * HD Fan control correction.
+ *
+ * # model_id: 2
+ * offset : -15650652
+ * slope : 1565065
+ *
+ * # model_id: 3
+ * offset : -19563152
+ * slope : 1956315
+ *
+ * CPU Fan control correction.
+ *
+ * # model_id: 2
+ * offset : -25431900
+ * slope : 2543190
+ *
+ * # model_id: 3
+ * offset : -15650652
+ * slope : 1565065
+ *
+ *
+ * Target rubber-banding :
+ *
+ * Some controls have a target correction which depends on another
+ * control value. The correction is computed in the following way :
+ *
+ * new_min = ref_value * slope + offset
+ *
+ * ref_value is the value of the reference control. If new_min is
+ * greater than 0, then we correct the target value using :
+ *
+ * new_target = max (new_target, new_min >> 16)
+ *
+ *
+ * # model_id : 2
+ * control : cpu-fan
+ * ref : optical-drive-fan
+ * offset : -15650652
+ * slope : 1565065
+ *
+ * # model_id : 3
+ * control : optical-drive-fan
+ * ref : hard-drive-fan
+ * offset : -32768000
+ * slope : 65536
+ *
+ *
+ * In order to have the moste efficient correction with those
+ * dependencies, we must trigger HD loop before OD loop before CPU
+ * loop.
+ *
+ *
+ * The various control loops found in Darwin config file are:
+ *
+ * HD Fan control loop.
+ *
+ * # model_id: 2
+ * control : hard-drive-fan
+ * sensor : hard-drive-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x002D70A3
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x370000
+ * Interval = 5s
+ *
+ * # model_id: 3
+ * control : hard-drive-fan
+ * sensor : hard-drive-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x002170A3
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x370000
+ * Interval = 5s
+ *
+ * OD Fan control loop.
+ *
+ * # model_id: 2
+ * control : optical-drive-fan
+ * sensor : optical-drive-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x001FAE14
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x320000
+ * Interval = 5s
+ *
+ * # model_id: 3
+ * control : optical-drive-fan
+ * sensor : optical-drive-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x001FAE14
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x320000
+ * Interval = 5s
+ *
+ * GPU Fan control loop.
+ *
+ * # model_id: 2
+ * control : hard-drive-fan
+ * sensor : gpu-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x002A6666
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x5A0000
+ * Interval = 5s
+ *
+ * # model_id: 3
+ * control : cpu-fan
+ * sensor : gpu-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x0010CCCC
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x500000
+ * Interval = 5s
+ *
+ * KODIAK (aka northbridge) Fan control loop.
+ *
+ * # model_id: 2
+ * control : optical-drive-fan
+ * sensor : north-bridge-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x003BD70A
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x550000
+ * Interval = 5s
+ *
+ * # model_id: 3
+ * control : hard-drive-fan
+ * sensor : north-bridge-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x0030F5C2
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x550000
+ * Interval = 5s
+ *
+ * CPU Fan control loop.
+ *
+ * control : cpu-fan
+ * sensors : cpu-temp, cpu-power
+ * PID params : from SDB partition
+ *
+ *
+ * CPU Slew control loop.
+ *
+ * control : cpufreq-clamp
+ * sensor : cpu-temp
+ *
+ */
+
+#undef DEBUG
+
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/init.h>
+#include <linux/spinlock.h>
+#include <linux/wait.h>
+#include <linux/kmod.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <asm/prom.h>
+#include <asm/machdep.h>
+#include <asm/io.h>
+#include <asm/system.h>
+#include <asm/sections.h>
+#include <asm/smu.h>
+
+#include "windfarm.h"
+#include "windfarm_pid.h"
+
+#define VERSION "0.3"
+
+static int pm121_mach_model; /* machine model id */
+
+/* Controls & sensors */
+static struct wf_sensor *sensor_cpu_power;
+static struct wf_sensor *sensor_cpu_temp;
+static struct wf_sensor *sensor_cpu_voltage;
+static struct wf_sensor *sensor_cpu_current;
+static struct wf_sensor *sensor_gpu_temp;
+static struct wf_sensor *sensor_north_bridge_temp;
+static struct wf_sensor *sensor_hard_drive_temp;
+static struct wf_sensor *sensor_optical_drive_temp;
+static struct wf_sensor *sensor_incoming_air_temp; /* unused ! */
+
+enum {
+ FAN_CPU,
+ FAN_HD,
+ FAN_OD,
+ CPUFREQ,
+ N_CONTROLS
+};
+static struct wf_control *controls[N_CONTROLS] = {};
+
+/* Set to kick the control loop into life */
+static int pm121_all_controls_ok, pm121_all_sensors_ok, pm121_started;
+
+enum {
+ FAILURE_FAN = 1 << 0,
+ FAILURE_SENSOR = 1 << 1,
+ FAILURE_OVERTEMP = 1 << 2
+};
+
+/* All sys loops. Note the HD before the OD loop in order to have it
+ run before. */
+enum {
+ LOOP_GPU, /* control = hd or cpu, but luckily,
+ it doesn't matter */
+ LOOP_HD, /* control = hd */
+ LOOP_KODIAK, /* control = hd or od */
+ LOOP_OD, /* control = od */
+ N_LOOPS
+};
+
+static const char *loop_names[N_LOOPS] = {
+ "GPU",
+ "HD",
+ "KODIAK",
+ "OD",
+};
+
+#define PM121_NUM_CONFIGS 2
+
+static unsigned int pm121_failure_state;
+static int pm121_readjust, pm121_skipping;
+static s32 average_power;
+
+struct pm121_correction {
+ int offset;
+ int slope;
+};
+
+static struct pm121_correction corrections[N_CONTROLS][PM121_NUM_CONFIGS] = {
+ /* FAN_OD */
+ {
+ /* MODEL 2 */
+ { .offset = -19563152,
+ .slope = 1956315
+ },
+ /* MODEL 3 */
+ { .offset = -15650652,
+ .slope = 1565065
+ },
+ },
+ /* FAN_HD */
+ {
+ /* MODEL 2 */
+ { .offset = -15650652,
+ .slope = 1565065
+ },
+ /* MODEL 3 */
+ { .offset = -19563152,
+ .slope = 1956315
+ },
+ },
+ /* FAN_CPU */
+ {
+ /* MODEL 2 */
+ { .offset = -25431900,
+ .slope = 2543190
+ },
+ /* MODEL 3 */
+ { .offset = -15650652,
+ .slope = 1565065
+ },
+ },
+ /* CPUFREQ has no correction (and is not implemented at all) */
+};
+
+struct pm121_connection {
+ unsigned int control_id;
+ unsigned int ref_id;
+ struct pm121_correction correction;
+};
+
+static struct pm121_connection pm121_connections[] = {
+ /* MODEL 2 */
+ { .control_id = FAN_CPU,
+ .ref_id = FAN_OD,
+ { .offset = -32768000,
+ .slope = 65536
+ }
+ },
+ /* MODEL 3 */
+ { .control_id = FAN_OD,
+ .ref_id = FAN_HD,
+ { .offset = -32768000,
+ .slope = 65536
+ }
+ },
+};
+
+/* pointer to the current model connection */
+static struct pm121_connection *pm121_connection;
+
+/*
+ * ****** System Fans Control Loop ******
+ *
+ */
+
+/* Since each loop handles only one control and we want to avoid
+ * writing virtual control, we store the control correction with the
+ * loop params. Some data are not set, there are common to all loop
+ * and thus, hardcoded.
+ */
+struct pm121_sys_param {
+ /* purely informative since we use mach_model-2 as index */
+ int model_id;
+ struct wf_sensor **sensor; /* use sensor_id instead ? */
+ s32 gp, itarget;
+ unsigned int control_id;
+};
+
+static struct pm121_sys_param
+pm121_sys_all_params[N_LOOPS][PM121_NUM_CONFIGS] = {
+ /* GPU Fan control loop */
+ {
+ { .model_id = 2,
+ .sensor = &sensor_gpu_temp,
+ .gp = 0x002A6666,
+ .itarget = 0x5A0000,
+ .control_id = FAN_HD,
+ },
+ { .model_id = 3,
+ .sensor = &sensor_gpu_temp,
+ .gp = 0x0010CCCC,
+ .itarget = 0x500000,
+ .control_id = FAN_CPU,
+ },
+ },
+ /* HD Fan control loop */
+ {
+ { .model_id = 2,
+ .sensor = &sensor_hard_drive_temp,
+ .gp = 0x002D70A3,
+ .itarget = 0x370000,
+ .control_id = FAN_HD,
+ },
+ { .model_id = 3,
+ .sensor = &sensor_hard_drive_temp,
+ .gp = 0x002170A3,
+ .itarget = 0x370000,
+ .control_id = FAN_HD,
+ },
+ },
+ /* KODIAK Fan control loop */
+ {
+ { .model_id = 2,
+ .sensor = &sensor_north_bridge_temp,
+ .gp = 0x003BD70A,
+ .itarget = 0x550000,
+ .control_id = FAN_OD,
+ },
+ { .model_id = 3,
+ .sensor = &sensor_north_bridge_temp,
+ .gp = 0x0030F5C2,
+ .itarget = 0x550000,
+ .control_id = FAN_HD,
+ },
+ },
+ /* OD Fan control loop */
+ {
+ { .model_id = 2,
+ .sensor = &sensor_optical_drive_temp,
+ .gp = 0x001FAE14,
+ .itarget = 0x320000,
+ .control_id = FAN_OD,
+ },
+ { .model_id = 3,
+ .sensor = &sensor_optical_drive_temp,
+ .gp = 0x001FAE14,
+ .itarget = 0x320000,
+ .control_id = FAN_OD,
+ },
+ },
+};
+
+/* the hardcoded values */
+#define PM121_SYS_GD 0x00000000
+#define PM121_SYS_GR 0x00019999
+#define PM121_SYS_HISTORY_SIZE 2
+#define PM121_SYS_INTERVAL 5
+
+/* State data used by the system fans control loop
+ */
+struct pm121_sys_state {
+ int ticks;
+ s32 setpoint;
+ struct wf_pid_state pid;
+};
+
+struct pm121_sys_state *pm121_sys_state[N_LOOPS] = {};
+
+/*
+ * ****** CPU Fans Control Loop ******
+ *
+ */
+
+#define PM121_CPU_INTERVAL 1
+
+/* State data used by the cpu fans control loop
+ */
+struct pm121_cpu_state {
+ int ticks;
+ s32 setpoint;
+ struct wf_cpu_pid_state pid;
+};
+
+static struct pm121_cpu_state *pm121_cpu_state;
+
+
+
+/*
+ * ***** Implementation *****
+ *
+ */
+
+/* correction the value using the output-low-bound correction algo */
+static s32 pm121_correct(s32 new_setpoint,
+ unsigned int control_id,
+ s32 min)
+{
+ s32 new_min;
+ struct pm121_correction *correction;
+ correction = &corrections[control_id][pm121_mach_model - 2];
+
+ new_min = (average_power * correction->slope) >> 16;
+ new_min += correction->offset;
+ new_min = (new_min >> 16) + min;
+
+ return max(new_setpoint, max(new_min, 0));
+}
+
+static s32 pm121_connect(unsigned int control_id, s32 setpoint)
+{
+ s32 new_min, value, new_setpoint;
+
+ if (pm121_connection->control_id == control_id) {
+ controls[control_id]->ops->get_value(controls[control_id],
+ &value);
+ new_min = value * pm121_connection->correction.slope;
+ new_min += pm121_connection->correction.offset;
+ if (new_min > 0) {
+ new_setpoint = max(setpoint, (new_min >> 16));
+ if (new_setpoint != setpoint) {
+ pr_debug("pm121: %s depending on %s, "
+ "corrected from %d to %d RPM\n",
+ controls[control_id]->name,
+ controls[pm121_connection->ref_id]->name,
+ (int) setpoint, (int) new_setpoint);
+ }
+ } else
+ new_setpoint = setpoint;
+ }
+ /* no connection */
+ else
+ new_setpoint = setpoint;
+
+ return new_setpoint;
+}
+
+/* FAN LOOPS */
+static void pm121_create_sys_fans(int loop_id)
+{
+ struct pm121_sys_param *param = NULL;
+ struct wf_pid_param pid_param;
+ struct wf_control *control = NULL;
+ int i;
+
+ /* First, locate the params for this model */
+ for (i = 0; i < PM121_NUM_CONFIGS; i++) {
+ if (pm121_sys_all_params[loop_id][i].model_id == pm121_mach_model) {
+ param = &(pm121_sys_all_params[loop_id][i]);
+ break;
+ }
+ }
+
+ /* No params found, put fans to max */
+ if (param == NULL) {
+ printk(KERN_WARNING "pm121: %s fan config not found "
+ " for this machine model\n",
+ loop_names[loop_id]);
+ goto fail;
+ }
+
+ control = controls[param->control_id];
+
+ /* Alloc & initialize state */
+ pm121_sys_state[loop_id] = kmalloc(sizeof(struct pm121_sys_state),
+ GFP_KERNEL);
+ if (pm121_sys_state[loop_id] == NULL) {
+ printk(KERN_WARNING "pm121: Memory allocation error\n");
+ goto fail;
+ }
+ pm121_sys_state[loop_id]->ticks = 1;
+
+ /* Fill PID params */
+ pid_param.gd = PM121_SYS_GD;
+ pid_param.gp = param->gp;
+ pid_param.gr = PM121_SYS_GR;
+ pid_param.interval = PM121_SYS_INTERVAL;
+ pid_param.history_len = PM121_SYS_HISTORY_SIZE;
+ pid_param.itarget = param->itarget;
+ pid_param.min = control->ops->get_min(control);
+ pid_param.max = control->ops->get_max(control);
+
+ wf_pid_init(&pm121_sys_state[loop_id]->pid, &pid_param);
+
+ pr_debug("pm121: %s Fan control loop initialized.\n"
+ " itarged=%d.%03d, min=%d RPM, max=%d RPM\n",
+ loop_names[loop_id], FIX32TOPRINT(pid_param.itarget),
+ pid_param.min, pid_param.max);
+ return;
+
+ fail:
+ /* note that this is not optimal since another loop may still
+ control the same control */
+ printk(KERN_WARNING "pm121: failed to set up %s loop "
+ "setting \"%s\" to max speed.\n",
+ loop_names[loop_id], control->name);
+
+ if (control)
+ wf_control_set_max(control);
+}
+
+static void pm121_sys_fans_tick(int loop_id)
+{
+ struct pm121_sys_param *param;
+ struct pm121_sys_state *st;
+ struct wf_sensor *sensor;
+ struct wf_control *control;
+ s32 temp, new_setpoint;
+ int rc;
+
+ param = &(pm121_sys_all_params[loop_id][pm121_mach_model-2]);
+ st = pm121_sys_state[loop_id];
+ sensor = *(param->sensor);
+ control = controls[param->control_id];
+
+ if (--st->ticks != 0) {
+ if (pm121_readjust)
+ goto readjust;
+ return;
+ }
+ st->ticks = PM121_SYS_INTERVAL;
+
+ rc = sensor->ops->get_value(sensor, &temp);
+ if (rc) {
+ printk(KERN_WARNING "windfarm: %s sensor error %d\n",
+ sensor->name, rc);
+ pm121_failure_state |= FAILURE_SENSOR;
+ return;
+ }
+
+ pr_debug("pm121: %s Fan tick ! %s: %d.%03d\n",
+ loop_names[loop_id], sensor->name,
+ FIX32TOPRINT(temp));
+
+ new_setpoint = wf_pid_run(&st->pid, temp);
+
+ /* correction */
+ new_setpoint = pm121_correct(new_setpoint,
+ param->control_id,
+ st->pid.param.min);
+ /* linked corretion */
+ new_setpoint = pm121_connect(param->control_id, new_setpoint);
+
+ if (new_setpoint == st->setpoint)
+ return;
+ st->setpoint = new_setpoint;
+ pr_debug("pm121: %s corrected setpoint: %d RPM\n",
+ control->name, (int)new_setpoint);
+ readjust:
+ if (control && pm121_failure_state == 0) {
+ rc = control->ops->set_value(control, st->setpoint);
+ if (rc) {
+ printk(KERN_WARNING "windfarm: %s fan error %d\n",
+ control->name, rc);
+ pm121_failure_state |= FAILURE_FAN;
+ }
+ }
+}
+
+
+/* CPU LOOP */
+static void pm121_create_cpu_fans(void)
+{
+ struct wf_cpu_pid_param pid_param;
+ const struct smu_sdbp_header *hdr;
+ struct smu_sdbp_cpupiddata *piddata;
+ struct smu_sdbp_fvt *fvt;
+ struct wf_control *fan_cpu;
+ s32 tmax, tdelta, maxpow, powadj;
+
+ fan_cpu = controls[FAN_CPU];
+
+ /* First, locate the PID params in SMU SBD */
+ hdr = smu_get_sdb_partition(SMU_SDB_CPUPIDDATA_ID, NULL);
+ if (hdr == 0) {
+ printk(KERN_WARNING "pm121: CPU PID fan config not found.\n");
+ goto fail;
+ }
+ piddata = (struct smu_sdbp_cpupiddata *)&hdr[1];
+
+ /* Get the FVT params for operating point 0 (the only supported one
+ * for now) in order to get tmax
+ */
+ hdr = smu_get_sdb_partition(SMU_SDB_FVT_ID, NULL);
+ if (hdr) {
+ fvt = (struct smu_sdbp_fvt *)&hdr[1];
+ tmax = ((s32)fvt->maxtemp) << 16;
+ } else
+ tmax = 0x5e0000; /* 94 degree default */
+
+ /* Alloc & initialize state */
+ pm121_cpu_state = kmalloc(sizeof(struct pm121_cpu_state),
+ GFP_KERNEL);
+ if (pm121_cpu_state == NULL)
+ goto fail;
+ pm121_cpu_state->ticks = 1;
+
+ /* Fill PID params */
+ pid_param.interval = PM121_CPU_INTERVAL;
+ pid_param.history_len = piddata->history_len;
+ if (pid_param.history_len > WF_CPU_PID_MAX_HISTORY) {
+ printk(KERN_WARNING "pm121: History size overflow on "
+ "CPU control loop (%d)\n", piddata->history_len);
+ pid_param.history_len = WF_CPU_PID_MAX_HISTORY;
+ }
+ pid_param.gd = piddata->gd;
+ pid_param.gp = piddata->gp;
+ pid_param.gr = piddata->gr / pid_param.history_len;
+
+ tdelta = ((s32)piddata->target_temp_delta) << 16;
+ maxpow = ((s32)piddata->max_power) << 16;
+ powadj = ((s32)piddata->power_adj) << 16;
+
+ pid_param.tmax = tmax;
+ pid_param.ttarget = tmax - tdelta;
+ pid_param.pmaxadj = maxpow - powadj;
+
+ pid_param.min = fan_cpu->ops->get_min(fan_cpu);
+ pid_param.max = fan_cpu->ops->get_max(fan_cpu);
+
+ wf_cpu_pid_init(&pm121_cpu_state->pid, &pid_param);
+
+ pr_debug("pm121: CPU Fan control initialized.\n");
+ pr_debug(" ttarged=%d.%03d, tmax=%d.%03d, min=%d RPM, max=%d RPM,\n",
+ FIX32TOPRINT(pid_param.ttarget), FIX32TOPRINT(pid_param.tmax),
+ pid_param.min, pid_param.max);
+
+ return;
+
+ fail:
+ printk(KERN_WARNING "pm121: CPU fan config not found, max fan speed\n");
+
+ if (controls[CPUFREQ])
+ wf_control_set_max(controls[CPUFREQ]);
+ if (fan_cpu)
+ wf_control_set_max(fan_cpu);
+}
+
+
+static void pm121_cpu_fans_tick(struct pm121_cpu_state *st)
+{
+ s32 new_setpoint, temp, power;
+ struct wf_control *fan_cpu = NULL;
+ int rc;
+
+ if (--st->ticks != 0) {
+ if (pm121_readjust)
+ goto readjust;
+ return;
+ }
+ st->ticks = PM121_CPU_INTERVAL;
+
+ fan_cpu = controls[FAN_CPU];
+
+ rc = sensor_cpu_temp->ops->get_value(sensor_cpu_temp, &temp);
+ if (rc) {
+ printk(KERN_WARNING "pm121: CPU temp sensor error %d\n",
+ rc);
+ pm121_failure_state |= FAILURE_SENSOR;
+ return;
+ }
+
+ rc = sensor_cpu_power->ops->get_value(sensor_cpu_power, &power);
+ if (rc) {
+ printk(KERN_WARNING "pm121: CPU power sensor error %d\n",
+ rc);
+ pm121_failure_state |= FAILURE_SENSOR;
+ return;
+ }
+
+ pr_debug("pm121: CPU Fans tick ! CPU temp: %d.%03d°C, power: %d.%03d\n",
+ FIX32TOPRINT(temp), FIX32TOPRINT(power));
+
+ if (temp > st->pid.param.tmax)
+ pm121_failure_state |= FAILURE_OVERTEMP;
+
+ new_setpoint = wf_cpu_pid_run(&st->pid, power, temp);
+
+ /* correction */
+ new_setpoint = pm121_correct(new_setpoint,
+ FAN_CPU,
+ st->pid.param.min);
+
+ /* connected correction */
+ new_setpoint = pm121_connect(FAN_CPU, new_setpoint);
+
+ if (st->setpoint == new_setpoint)
+ return;
+ st->setpoint = new_setpoint;
+ pr_debug("pm121: CPU corrected setpoint: %d RPM\n", (int)new_setpoint);
+
+ readjust:
+ if (fan_cpu && pm121_failure_state == 0) {
+ rc = fan_cpu->ops->set_value(fan_cpu, st->setpoint);
+ if (rc) {
+ printk(KERN_WARNING "pm121: %s fan error %d\n",
+ fan_cpu->name, rc);
+ pm121_failure_state |= FAILURE_FAN;
+ }
+ }
+}
+
+/*
+ * ****** Common ******
+ *
+ */
+
+static void pm121_tick(void)
+{
+ unsigned int last_failure = pm121_failure_state;
+ unsigned int new_failure;
+ s32 total_power;
+ int i;
+
+ if (!pm121_started) {
+ pr_debug("pm121: creating control loops !\n");
+ for (i = 0; i < N_LOOPS; i++)
+ pm121_create_sys_fans(i);
+
+ pm121_create_cpu_fans();
+ pm121_started = 1;
+ }
+
+ /* skipping ticks */
+ if (pm121_skipping && --pm121_skipping)
+ return;
+
+ /* compute average power */
+ total_power = 0;
+ for (i = 0; i < pm121_cpu_state->pid.param.history_len; i++)
+ total_power += pm121_cpu_state->pid.powers[i];
+
+ average_power = total_power / pm121_cpu_state->pid.param.history_len;
+
+
+ pm121_failure_state = 0;
+ for (i = 0 ; i < N_LOOPS; i++) {
+ if (pm121_sys_state[i])
+ pm121_sys_fans_tick(i);
+ }
+
+ if (pm121_cpu_state)
+ pm121_cpu_fans_tick(pm121_cpu_state);
+
+ pm121_readjust = 0;
+ new_failure = pm121_failure_state & ~last_failure;
+
+ /* If entering failure mode, clamp cpufreq and ramp all
+ * fans to full speed.
+ */
+ if (pm121_failure_state && !last_failure) {
+ for (i = 0; i < N_CONTROLS; i++) {
+ if (controls[i])
+ wf_control_set_max(controls[i]);
+ }
+ }
+
+ /* If leaving failure mode, unclamp cpufreq and readjust
+ * all fans on next iteration
+ */
+ if (!pm121_failure_state && last_failure) {
+ if (controls[CPUFREQ])
+ wf_control_set_min(controls[CPUFREQ]);
+ pm121_readjust = 1;
+ }
+
+ /* Overtemp condition detected, notify and start skipping a couple
+ * ticks to let the temperature go down
+ */
+ if (new_failure & FAILURE_OVERTEMP) {
+ wf_set_overtemp();
+ pm121_skipping = 2;
+ }
+
+ /* We only clear the overtemp condition if overtemp is cleared
+ * _and_ no other failure is present. Since a sensor error will
+ * clear the overtemp condition (can't measure temperature) at
+ * the control loop levels, but we don't want to keep it clear
+ * here in this case
+ */
+ if (new_failure == 0 && last_failure & FAILURE_OVERTEMP)
+ wf_clear_overtemp();
+}
+
+
+static struct wf_control* pm121_register_control(struct wf_control *ct,
+ const char *match,
+ unsigned int id)
+{
+ if (controls[id] == NULL && !strcmp(ct->name, match)) {
+ if (wf_get_control(ct) == 0)
+ controls[FAN_OD] = ct;
+ }
+ return controls[id];
+}
+
+static void pm121_new_control(struct wf_control *ct)
+{
+ int all = 1;
+
+ if (pm121_all_controls_ok)
+ return;
+
+ all = all && pm121_register_control(ct, "optical-driver-fan", FAN_OD);
+ all = all && pm121_register_control(ct, "hard-driver-fan", FAN_HD);
+ all = all && pm121_register_control(ct, "cpu-driver-fan", FAN_CPU);
+ all = all && pm121_register_control(ct, "cpufreq-clamp", CPUFREQ);
+
+ if (all)
+ pm121_all_controls_ok = 1;
+}
+
+
+
+
+static struct wf_sensor* pm121_register_sensor(struct wf_sensor *sensor,
+ const char *match,
+ struct wf_sensor **var)
+{
+ if (*var == NULL && !strcmp(sensor->name, match)) {
+ if (wf_get_sensor(sensor) == 0)
+ *var = sensor;
+ }
+ return *var;
+}
+
+static void pm121_new_sensor(struct wf_sensor *sr)
+{
+ int all = 1;
+
+ if (pm121_all_sensors_ok)
+ return;
+
+ all = all && pm121_register_sensor(sr, "cpu-temp",
+ &sensor_cpu_temp);
+ all = all && pm121_register_sensor(sr, "cpu-current",
+ &sensor_cpu_current);
+ all = all && pm121_register_sensor(sr, "cpu-voltage",
+ &sensor_cpu_voltage);
+ all = all && pm121_register_sensor(sr, "cpu-power",
+ &sensor_cpu_power);
+ all = all && pm121_register_sensor(sr, "hard-drive-temp",
+ &sensor_hard_drive_temp);
+ all = all && pm121_register_sensor(sr, "optical-drive-temp",
+ &sensor_optical_drive_temp);
+ all = all && pm121_register_sensor(sr, "incoming-air-temp",
+ &sensor_incoming_air_temp);
+ all = all && pm121_register_sensor(sr, "north-bridge-temp",
+ &sensor_north_bridge_temp);
+ all = all && pm121_register_sensor(sr, "gpu-temp",
+ &sensor_gpu_temp);
+
+ if (all)
+ pm121_all_sensors_ok = 1;
+}
+
+
+
+static int pm121_notify(struct notifier_block *self,
+ unsigned long event, void *data)
+{
+ switch (event) {
+ case WF_EVENT_NEW_CONTROL:
+ pr_debug("pm121: new control %s detected\n",
+ ((struct wf_control *)data)->name);
+ pm121_new_control(data);
+ break;
+ case WF_EVENT_NEW_SENSOR:
+ pr_debug("pm121: new sensor %s detected\n",
+ ((struct wf_sensor *)data)->name);
+ pm121_new_sensor(data);
+ break;
+ case WF_EVENT_TICK:
+ if (pm121_all_controls_ok && pm121_all_sensors_ok)
+ pm121_tick();
+ break;
+ }
+
+ return 0;
+}
+
+static struct notifier_block pm121_events = {
+ .notifier_call = pm121_notify,
+};
+
+static int pm121_init_pm(void)
+{
+ const struct smu_sdbp_header *hdr;
+
+ hdr = smu_get_sdb_partition(SMU_SDB_SENSORTREE_ID, NULL);
+ if (hdr != 0) {
+ struct smu_sdbp_sensortree *st =
+ (struct smu_sdbp_sensortree *)&hdr[1];
+ pm121_mach_model = st->model_id;
+ }
+
+ pm121_connection = &pm121_connections[pm121_mach_model - 2];
+
+ printk(KERN_INFO "pm121: Initializing for iMac G5 iSight model ID %d\n",
+ pm121_mach_model);
+
+ return 0;
+}
+
+
+static int pm121_probe(struct platform_device *ddev)
+{
+ wf_register_client(&pm121_events);
+
+ return 0;
+}
+
+static int __devexit pm121_remove(struct platform_device *ddev)
+{
+ wf_unregister_client(&pm121_events);
+ return 0;
+}
+
+static struct platform_driver pm121_driver = {
+ .probe = pm121_probe,
+ .remove = __devexit_p(pm121_remove),
+ .driver = {
+ .name = "windfarm",
+ .bus = &platform_bus_type,
+ },
+};
+
+
+static int __init pm121_init(void)
+{
+ int rc = -ENODEV;
+
+ if (machine_is_compatible("PowerMac12,1"))
+ rc = pm121_init_pm();
+
+ if (rc == 0) {
+ request_module("windfarm_smu_controls");
+ request_module("windfarm_smu_sensors");
+ request_module("windfarm_smu_sat");
+ request_module("windfarm_lm75_sensor");
+ request_module("windfarm_max6690_sensor");
+ request_module("windfarm_cpufreq_clamp");
+ platform_driver_register(&pm121_driver);
+ }
+
+ return rc;
+}
+
+static void __exit pm121_exit(void)
+{
+
+ platform_driver_unregister(&pm121_driver);
+}
+
+
+module_init(pm121_init);
+module_exit(pm121_exit);
+
+MODULE_AUTHOR("Étienne Bersac <bersace@gmail.com>");
+MODULE_DESCRIPTION("Thermal control logic for iMac G5 (iSight)");
+MODULE_LICENSE("GPL");
+
diff --git a/drivers/macintosh/windfarm_smu_controls.c b/drivers/macintosh/windfarm_smu_controls.c
index 58c2590..961fa0e 100644
--- a/drivers/macintosh/windfarm_smu_controls.c
+++ b/drivers/macintosh/windfarm_smu_controls.c
@@ -218,6 +218,10 @@ static struct smu_fan_control *smu_fan_create(struct device_node *node,
fct->ctrl.name = "cpu-fan";
else if (!strcmp(l, "Hard Drive") || !strcmp(l, "Hard drive"))
fct->ctrl.name = "drive-bay-fan";
+ else if (!strcmp(l, "HDD Fan")) /* seen on iMac G5 iSight */
+ fct->ctrl.name = "hard-drive-fan";
+ else if (!strcmp(l, "ODD Fan")) /* same */
+ fct->ctrl.name = "optical-drive-fan";
/* Unrecognized fan, bail out */
if (fct->ctrl.name == NULL)
^ permalink raw reply related
* Re: [PATCH 2/3] Use embedded libfdt in the bootwrapper
From: Scott Wood @ 2007-12-10 17:32 UTC (permalink / raw)
To: David Gibson; +Cc: linuxppc-dev, Paul Mackerras
In-Reply-To: <20071210032839.71412DDDFA@ozlabs.org>
On Mon, Dec 10, 2007 at 02:28:39PM +1100, David Gibson wrote:
> +#define check_err(err) \
> + ({ \
> + if (BAD_ERROR(err) || ((err < 0) && DEBUG)) \
> + printf("%s():%d %s\n\r", __FUNCTION__, __LINE__, \
> + fdt_strerror(err)); \
> + if (BAD_ERROR(err)) \
> + exit(); \
> + (err < 0) ? -1 : 0; \
> + })
> +
> +#define offset_devp(off) \
> + ({ \
> + int offset = (off); \
> + check_err(offset) ? NULL : (void *)(offset+1); \
> + })
> +
> +#define devp_offset(devp) (((int)(devp))-1)
How does using offsets as devps work if a devp was previously acquired to a
node that has to be moved due to a change later made in an earlier part of
the tree?
-Scott
^ permalink raw reply
* Re: [PATCH] IB/ehca: Serialize HCA-related hCalls on POWER5
From: Joachim Fenkes @ 2007-12-10 17:41 UTC (permalink / raw)
To: Roland Dreier
Cc: Arnd Bergmann, LKML, OF-EWG, linuxppc-dev, Christoph Raisch,
Marcus Eder, OF-General, Stefan Roscher
In-Reply-To: <adaodcza1xc.fsf@cisco.com>
On Monday 10 December 2007 00:22, Roland Dreier wrote:
> Fair enough... according to Documentation/infiniband/core_locking.txt,
> the only driver methods that cannot sleep are:
>
> [...]
> map_phys_fmr
In fact, we do use hCalls there. Our hardware doesn't actually support FMRs,
so we translate a "map FMR" into a "reallocate PMR", which doesn't work
without hCalls. What's more, the hCalls involved (e.g. H_FREE_RESOURCE)
might well return H_LONG_BUSY, so the whole operation might sleep; no way
around it.
How should we deal with this?
Thanks,
Joachim
^ permalink raw reply
* Re: [PATCH] IB/ehca: Serialize HCA-related hCalls on POWER5
From: Joachim Fenkes @ 2007-12-10 17:59 UTC (permalink / raw)
To: Arnd Bergmann, OF-EWG, OF-General, LKML, linuxppc-dev,
Roland Dreier, Roland Dreier
Cc: Christoph Raisch, Stefan Roscher, Marcus Eder
In-Reply-To: <OF85E31FAA.DADA6039-ONC12573AA.005439C8-C12573AA.005A132E@LocalDomain>
Hi, guys,
> We're taking this to the firmware architects at the moment, but they're
not
> very fond of the idea of reporting the absence of bugs through
capability
> flags, as this could quickly lead to the exhaustion of flag bits. We'll
let
> the discussion stew for a bit, but if we don't get this flag, we'll have
to
> resort to the CPU features.
The architects have spoken, and we're getting a capability flag for this.
I'll repost my patch with new autodetection code that doesn't involve
checking the processor version.
> > > Regarding the performance problem, have you checked whether
converting all
> > > your spin_lock_irqsave to spin_lock/spin_lock_irq improves your
performance
> > > on the older machines? Maybe it's already fast enough that way.
> >
> > It does seem that the only places that the hcall_lock is taken also
> > use msleep, so they must always be in process context. So you can
> > safely just use spin_lock(), right?
>
> As Arnd said, there are hCalls that will never return H_LONG_BUSY_*,
such as
> H_QUERY_PORT and chums, so they will never sleep. The surrounding
functions,
> though, are not prepared to be called from interrupt context (GFP_KERNEL
comes
> to mind), so I agree that a simple spin_lock() will suffice. Thanks,
Arnd, for
> pointing this out.
As I pointed out in my earlier mail, there's still an issue with
map_phys_fmr possibly sleeping. Let's keep the irqsave for the time being
and revisit this part once we find a solution to map_phys_fmr.
Regards,
Joachim
^ permalink raw reply
* [PATCH] IB/ehca: Serialize HCA-related hCalls if necessary
From: Joachim Fenkes @ 2007-12-10 17:59 UTC (permalink / raw)
To: LinuxPPC-Dev, LKML, OF-General, Roland Dreier, OF-EWG,
Arnd Bergmann
Cc: Stefan Roscher, Christoph Raisch, Marcus Eder
Several pSeries firmware versions share a rare locking issue in the
HCA-related hCalls. Check for a feature flag that indicates the issue being
fixed and serialize all HCA hCalls if not.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
---
This is the revised version of my previous patch, which does not rely on the
processor version any longer.
drivers/infiniband/hw/ehca/ehca_main.c | 13 +++++++++++++
drivers/infiniband/hw/ehca/hcp_if.c | 28 +++++++++++-----------------
drivers/infiniband/hw/ehca/hipz_hw.h | 1 +
3 files changed, 25 insertions(+), 17 deletions(-)
diff --git a/drivers/infiniband/hw/ehca/ehca_main.c b/drivers/infiniband/hw/ehca/ehca_main.c
index 90d4334..c7bff3e 100644
--- a/drivers/infiniband/hw/ehca/ehca_main.c
+++ b/drivers/infiniband/hw/ehca/ehca_main.c
@@ -43,6 +43,7 @@
#ifdef CONFIG_PPC_64K_PAGES
#include <linux/slab.h>
#endif
+
#include "ehca_classes.h"
#include "ehca_iverbs.h"
#include "ehca_mrmw.h"
@@ -66,6 +67,7 @@ int ehca_poll_all_eqs = 1;
int ehca_static_rate = -1;
int ehca_scaling_code = 0;
int ehca_mr_largepage = 1;
+int ehca_lock_hcalls = -1;
module_param_named(open_aqp1, ehca_open_aqp1, int, S_IRUGO);
module_param_named(debug_level, ehca_debug_level, int, S_IRUGO);
@@ -77,6 +79,7 @@ module_param_named(poll_all_eqs, ehca_poll_all_eqs, int, S_IRUGO);
module_param_named(static_rate, ehca_static_rate, int, S_IRUGO);
module_param_named(scaling_code, ehca_scaling_code, int, S_IRUGO);
module_param_named(mr_largepage, ehca_mr_largepage, int, S_IRUGO);
+module_param_named(lock_hcalls, ehca_lock_hcalls, bool, S_IRUGO);
MODULE_PARM_DESC(open_aqp1,
"AQP1 on startup (0: no (default), 1: yes)");
@@ -102,6 +105,9 @@ MODULE_PARM_DESC(scaling_code,
MODULE_PARM_DESC(mr_largepage,
"use large page for MR (0: use PAGE_SIZE (default), "
"1: use large page depending on MR size");
+MODULE_PARM_DESC(lock_hcalls,
+ "serialize all hCalls made by the driver "
+ "(default: autodetect)");
DEFINE_RWLOCK(ehca_qp_idr_lock);
DEFINE_RWLOCK(ehca_cq_idr_lock);
@@ -258,6 +264,7 @@ static struct cap_descr {
{ HCA_CAP_UD_LL_QP, "HCA_CAP_UD_LL_QP" },
{ HCA_CAP_RESIZE_MR, "HCA_CAP_RESIZE_MR" },
{ HCA_CAP_MINI_QP, "HCA_CAP_MINI_QP" },
+ { HCA_CAP_H_ALLOC_RES_SYNC, "HCA_CAP_H_ALLOC_RES_SYNC" },
};
static int ehca_sense_attributes(struct ehca_shca *shca)
@@ -333,6 +340,12 @@ static int ehca_sense_attributes(struct ehca_shca *shca)
if (EHCA_BMASK_GET(hca_cap_descr[i].mask, shca->hca_cap))
ehca_gen_dbg(" %s", hca_cap_descr[i].descr);
+ /* Autodetect hCall locking -- the "H_ALLOC_RESOURCE synced" flag is
+ * a firmware property, so it's valid across all adapters
+ */
+ if (ehca_lock_hcalls == -1)
+ ehca_lock_hcalls = !(shca->hca_cap & HCA_CAP_H_ALLOC_RES_SYNC);
+
/* translate supported MR page sizes; always support 4K */
shca->hca_cap_mr_pgsize = EHCA_PAGESIZE;
if (ehca_mr_largepage) { /* support extra sizes only if enabled */
diff --git a/drivers/infiniband/hw/ehca/hcp_if.c b/drivers/infiniband/hw/ehca/hcp_if.c
index c16a213..331b5e8 100644
--- a/drivers/infiniband/hw/ehca/hcp_if.c
+++ b/drivers/infiniband/hw/ehca/hcp_if.c
@@ -89,6 +89,7 @@
#define HCALL9_REGS_FORMAT HCALL7_REGS_FORMAT " r11=%lx r12=%lx"
static DEFINE_SPINLOCK(hcall_lock);
+extern int ehca_lock_hcalls;
static u32 get_longbusy_msecs(int longbusy_rc)
{
@@ -120,26 +121,21 @@ static long ehca_plpar_hcall_norets(unsigned long opcode,
unsigned long arg7)
{
long ret;
- int i, sleep_msecs, do_lock;
- unsigned long flags;
+ int i, sleep_msecs;
+ unsigned long flags = 0;
ehca_gen_dbg("opcode=%lx " HCALL7_REGS_FORMAT,
opcode, arg1, arg2, arg3, arg4, arg5, arg6, arg7);
- /* lock H_FREE_RESOURCE(MR) against itself and H_ALLOC_RESOURCE(MR) */
- if ((opcode == H_FREE_RESOURCE) && (arg7 == 5)) {
- arg7 = 0; /* better not upset firmware */
- do_lock = 1;
- }
-
for (i = 0; i < 5; i++) {
- if (do_lock)
+ /* serialize hCalls to work around firmware issue */
+ if (ehca_lock_hcalls)
spin_lock_irqsave(&hcall_lock, flags);
ret = plpar_hcall_norets(opcode, arg1, arg2, arg3, arg4,
arg5, arg6, arg7);
- if (do_lock)
+ if (ehca_lock_hcalls)
spin_unlock_irqrestore(&hcall_lock, flags);
if (H_IS_LONG_BUSY(ret)) {
@@ -174,24 +170,22 @@ static long ehca_plpar_hcall9(unsigned long opcode,
unsigned long arg9)
{
long ret;
- int i, sleep_msecs, do_lock;
+ int i, sleep_msecs;
unsigned long flags = 0;
ehca_gen_dbg("INPUT -- opcode=%lx " HCALL9_REGS_FORMAT, opcode,
arg1, arg2, arg3, arg4, arg5, arg6, arg7, arg8, arg9);
- /* lock H_ALLOC_RESOURCE(MR) against itself and H_FREE_RESOURCE(MR) */
- do_lock = ((opcode == H_ALLOC_RESOURCE) && (arg2 == 5));
-
for (i = 0; i < 5; i++) {
- if (do_lock)
+ /* serialize hCalls to work around firmware issue */
+ if (ehca_lock_hcalls)
spin_lock_irqsave(&hcall_lock, flags);
ret = plpar_hcall9(opcode, outs,
arg1, arg2, arg3, arg4, arg5,
arg6, arg7, arg8, arg9);
- if (do_lock)
+ if (ehca_lock_hcalls)
spin_unlock_irqrestore(&hcall_lock, flags);
if (H_IS_LONG_BUSY(ret)) {
@@ -821,7 +815,7 @@ u64 hipz_h_free_resource_mr(const struct ipz_adapter_handle adapter_handle,
return ehca_plpar_hcall_norets(H_FREE_RESOURCE,
adapter_handle.handle, /* r4 */
mr->ipz_mr_handle.handle, /* r5 */
- 0, 0, 0, 0, 5);
+ 0, 0, 0, 0, 0);
}
u64 hipz_h_reregister_pmr(const struct ipz_adapter_handle adapter_handle,
diff --git a/drivers/infiniband/hw/ehca/hipz_hw.h b/drivers/infiniband/hw/ehca/hipz_hw.h
index 485b840..bf996c7 100644
--- a/drivers/infiniband/hw/ehca/hipz_hw.h
+++ b/drivers/infiniband/hw/ehca/hipz_hw.h
@@ -378,6 +378,7 @@ struct hipz_query_hca {
#define HCA_CAP_UD_LL_QP EHCA_BMASK_IBM(16, 16)
#define HCA_CAP_RESIZE_MR EHCA_BMASK_IBM(17, 17)
#define HCA_CAP_MINI_QP EHCA_BMASK_IBM(18, 18)
+#define HCA_CAP_H_ALLOC_RES_SYNC EHCA_BMASK_IBM(19, 19)
/* query port response block */
struct hipz_query_port {
--
1.5.2
^ permalink raw reply related
* Re: [PATCH 4/25] powerpc: Reworking machine check handling and Fix 440/440A
From: Josh Boyer @ 2007-12-10 17:59 UTC (permalink / raw)
To: Benjamin Herrenschmidt; +Cc: linuxppc-dev
In-Reply-To: <20071206080114.CDB13DDE33@ozlabs.org>
On Thu, 06 Dec 2007 19:00:03 +1100
Benjamin Herrenschmidt <benh@kernel.crashing.org> wrote:
> This adds a cputable function pointer for the CPU-side machine
> check handling. The semantic is still the same as the old one,
> the one in ppc_md. overrides the one in cputable, though
> ultimately we'll want to change that so the CPU gets first.
>
> This removes CONFIG_440A which was a problem for multiplatform
> kernels and instead fixes up the IVOR at runtime from a setup_cpu
> function. The "A" version of the machine check also tweaks the
> regs->trap value to differenciate the 2 versions at the C level.
This breaks ARCH=ppc builds. Unfortunately, that tree shares the
cputable.[ch] files, but has it's own traps.c. Which means you get
lots of nice undefined references like below for example:
arch/powerpc/kernel/built-in.o:(.init.data+0x44): undefined reference to `machine_check_4xx'
arch/powerpc/kernel/built-in.o:(.init.data+0x8c): undefined reference to `machine_check_4xx'
arch/powerpc/kernel/built-in.o:(.init.data+0xd4): undefined reference to `machine_check_4xx'
Because the cputable entries for the processors are setting the .machine_check function and it's never built.
I'm not sure which would be easier, making arch/ppc use traps.c from arch/powerpc, or adding similar functionality there.
josh
^ permalink raw reply
* Re: [i2c] [PATCH 0/4] Series to add device tree naming to i2c
From: Jon Smirl @ 2007-12-10 18:06 UTC (permalink / raw)
To: Scott Wood; +Cc: Jean Delvare, i2c, linuxppc-dev
In-Reply-To: <20071210164255.GA4497@loki.buserror.net>
On 12/10/07, Scott Wood <scottwood@freescale.com> wrote:
> On Mon, Dec 10, 2007 at 08:38:46AM +1100, Benjamin Herrenschmidt wrote:
> > The more I think about it, the more I tend to agree that tagging isn't
> > necessary and you are right. We should just match the name against the
> > "compatible" property of the OF nodes (which mean we need to support
> > multiple matches though since "compatible" is a list of strings).
>
> It may not be strictly necessary, but I think it's a good idea not just for
> safety reasons, but as an indication to the driver what additional
> information it has access to. We could put a match data pointer in the i2c
> device, and have it be a valid node pointer if the match was an OF one (and
> a device-specific struct for a straight platform device, etc). This could
> be useful if a device needs to have more properties than standard
> address/type/interrupt for some reason.
I can't see an easy way to do this. The basic problem is that the i2c
drivers are assumed to be cross platform. I would need to add a path
through the i2c core for getting a void pointer from the bus to the
device But then when the device code gets this pointer it has no way
of knowing what it was. Assuming the void is a pointer to an of_node
would make the driver for the i2c device platform specific.
Another way that would work cross platform would be for the module to
have module parameters for the extra attributes. The bus code could
then look in the of_node for extra attributes and use them to set the
module parameters. I know this can be done, but doing it is a little
above my understanding of the module code. You need to ask the module
it's parameter names, addresses and types and then match them to
attributes in the of_node and do the copy.
>
> -Scott
>
--
Jon Smirl
jonsmirl@gmail.com
^ permalink raw reply
* [PATCH 2/5] Modify several rtc drivers to use the alias names list property of i2c
From: Jon Smirl @ 2007-12-10 18:33 UTC (permalink / raw)
To: i2c, linuxppc-dev
In-Reply-To: <20071210183323.12584.88127.stgit@terra.home>
This patch modifies the ds1307, ds1374, and rs5c372 i2c drivers to support
device tree names using the new i2c mod alias support
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
---
arch/powerpc/sysdev/fsl_soc.c | 44 ++++++-----------------------------------
drivers/rtc/rtc-ds1307.c | 38 +++++++++++++++++++----------------
drivers/rtc/rtc-ds1374.c | 11 +++++++++-
drivers/rtc/rtc-rs5c372.c | 31 ++++++++++++++++-------------
4 files changed, 53 insertions(+), 71 deletions(-)
diff --git a/arch/powerpc/sysdev/fsl_soc.c b/arch/powerpc/sysdev/fsl_soc.c
index 3ace747..268638a 100644
--- a/arch/powerpc/sysdev/fsl_soc.c
+++ b/arch/powerpc/sysdev/fsl_soc.c
@@ -320,48 +320,12 @@ arch_initcall(gfar_of_init);
#ifdef CONFIG_I2C_BOARDINFO
#include <linux/i2c.h>
-struct i2c_driver_device {
- char *of_device;
- char *i2c_driver;
- char *i2c_type;
-};
-
-static struct i2c_driver_device i2c_devices[] __initdata = {
- {"ricoh,rs5c372a", "rtc-rs5c372", "rs5c372a",},
- {"ricoh,rs5c372b", "rtc-rs5c372", "rs5c372b",},
- {"ricoh,rv5c386", "rtc-rs5c372", "rv5c386",},
- {"ricoh,rv5c387a", "rtc-rs5c372", "rv5c387a",},
- {"dallas,ds1307", "rtc-ds1307", "ds1307",},
- {"dallas,ds1337", "rtc-ds1307", "ds1337",},
- {"dallas,ds1338", "rtc-ds1307", "ds1338",},
- {"dallas,ds1339", "rtc-ds1307", "ds1339",},
- {"dallas,ds1340", "rtc-ds1307", "ds1340",},
- {"stm,m41t00", "rtc-ds1307", "m41t00"},
- {"dallas,ds1374", "rtc-ds1374", "rtc-ds1374",},
-};
-
-static int __init of_find_i2c_driver(struct device_node *node,
- struct i2c_board_info *info)
-{
- int i;
-
- for (i = 0; i < ARRAY_SIZE(i2c_devices); i++) {
- if (!of_device_is_compatible(node, i2c_devices[i].of_device))
- continue;
- if (strlcpy(info->driver_name, i2c_devices[i].i2c_driver,
- KOBJ_NAME_LEN) >= KOBJ_NAME_LEN ||
- strlcpy(info->type, i2c_devices[i].i2c_type,
- I2C_NAME_SIZE) >= I2C_NAME_SIZE)
- return -ENOMEM;
- return 0;
- }
- return -ENODEV;
-}
static void __init of_register_i2c_devices(struct device_node *adap_node,
int bus_num)
{
struct device_node *node = NULL;
+ const char *compatible;
while ((node = of_get_next_child(adap_node, node))) {
struct i2c_board_info info = {};
@@ -378,8 +342,12 @@ static void __init of_register_i2c_devices(struct device_node *adap_node,
if (info.irq == NO_IRQ)
info.irq = -1;
- if (of_find_i2c_driver(node, &info) < 0)
+ compatible = of_get_property(node, "compatible", &len);
+ if (!compatible) {
+ printk(KERN_WARNING "i2c-mpc.c: invalid entry, missing compatible attribute\n");
continue;
+ }
+ strncpy(info.driver_name, compatible, sizeof(info.driver_name));
info.addr = *addr;
diff --git a/drivers/rtc/rtc-ds1307.c b/drivers/rtc/rtc-ds1307.c
index bc1c7fe..a4dec4b 100644
--- a/drivers/rtc/rtc-ds1307.c
+++ b/drivers/rtc/rtc-ds1307.c
@@ -99,45 +99,46 @@ struct ds1307 {
};
struct chip_desc {
- char name[9];
unsigned nvram56:1;
unsigned alarm:1;
enum ds_type type;
};
static const struct chip_desc chips[] = { {
- .name = "ds1307",
.type = ds_1307,
.nvram56 = 1,
}, {
- .name = "ds1337",
.type = ds_1337,
.alarm = 1,
}, {
- .name = "ds1338",
.type = ds_1338,
.nvram56 = 1,
}, {
- .name = "ds1339",
.type = ds_1339,
.alarm = 1,
}, {
- .name = "ds1340",
.type = ds_1340,
}, {
- .name = "m41t00",
.type = m41t00,
}, };
-static inline const struct chip_desc *find_chip(const char *s)
-{
- unsigned i;
-
- for (i = 0; i < ARRAY_SIZE(chips); i++)
- if (strnicmp(s, chips[i].name, sizeof chips[i].name) == 0)
- return &chips[i];
- return NULL;
-}
+static struct i2c_device_id ds1307_id[] = {
+ {"rtc-ds1307", ds_1307},
+ {"ds1307", ds_1307},
+ {"ds1337", ds_1337},
+ {"ds1338", ds_1338},
+ {"ds1339", ds_1339},
+ {"ds1340", ds_1340},
+ {"m41t00", m41t00},
+ {"dallas,ds1307", ds_1307},
+ {"dallas,ds1337", ds_1337},
+ {"dallas,ds1338", ds_1338},
+ {"dallas,ds1339", ds_1339},
+ {"dallas,ds1340", ds_1340},
+ {"stm,m41t00", m41t00},
+ {},
+};
+MODULE_DEVICE_TABLE(i2c, ds1307_id);
static int ds1307_get_time(struct device *dev, struct rtc_time *t)
{
@@ -326,7 +327,7 @@ static struct bin_attribute nvram = {
static struct i2c_driver ds1307_driver;
-static int __devinit ds1307_probe(struct i2c_client *client)
+static int __devinit ds1307_probe(struct i2c_client *client, const struct i2c_device_id *id)
{
struct ds1307 *ds1307;
int err = -ENODEV;
@@ -334,7 +335,7 @@ static int __devinit ds1307_probe(struct i2c_client *client)
const struct chip_desc *chip;
struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent);
- chip = find_chip(client->name);
+ chip = &chips[id->driver_data];
if (!chip) {
dev_err(&client->dev, "unknown chip type '%s'\n",
client->name);
@@ -537,6 +538,7 @@ static struct i2c_driver ds1307_driver = {
},
.probe = ds1307_probe,
.remove = __devexit_p(ds1307_remove),
+ .id_table = ds1307_id,
};
static int __init ds1307_init(void)
diff --git a/drivers/rtc/rtc-ds1374.c b/drivers/rtc/rtc-ds1374.c
index 45bda18..2b852f3 100644
--- a/drivers/rtc/rtc-ds1374.c
+++ b/drivers/rtc/rtc-ds1374.c
@@ -41,6 +41,14 @@
#define DS1374_REG_SR_AF 0x01 /* Alarm Flag */
#define DS1374_REG_TCR 0x09 /* Trickle Charge */
+static struct i2c_device_id ds1374_id[] = {
+ {"rtc-ds1374", 0},
+ {"ds1374", 0},
+ {"dallas,ds1374", 0},
+ {},
+};
+MODULE_DEVICE_TABLE(i2c, ds1374_id);
+
struct ds1374 {
struct i2c_client *client;
struct rtc_device *rtc;
@@ -355,7 +363,7 @@ static const struct rtc_class_ops ds1374_rtc_ops = {
.ioctl = ds1374_ioctl,
};
-static int ds1374_probe(struct i2c_client *client)
+static int ds1374_probe(struct i2c_client *client, const struct i2c_device_id *id)
{
struct ds1374 *ds1374;
int ret;
@@ -429,6 +437,7 @@ static struct i2c_driver ds1374_driver = {
},
.probe = ds1374_probe,
.remove = __devexit_p(ds1374_remove),
+ .id_table = ds1374_id,
};
static int __init ds1374_init(void)
diff --git a/drivers/rtc/rtc-rs5c372.c b/drivers/rtc/rtc-rs5c372.c
index 6b67b50..de0d458 100644
--- a/drivers/rtc/rtc-rs5c372.c
+++ b/drivers/rtc/rtc-rs5c372.c
@@ -62,13 +62,26 @@
enum rtc_type {
- rtc_undef = 0,
rtc_rs5c372a,
rtc_rs5c372b,
rtc_rv5c386,
rtc_rv5c387a,
};
+static struct i2c_device_id rs5c372_id[] = {
+ {"rtc-rs5c372", rtc_rs5c372a},
+ {"rs5c372a", rtc_rs5c372a},
+ {"rs5c372b", rtc_rs5c372b},
+ {"rv5c386", rtc_rv5c386},
+ {"rv5c387a", rtc_rv5c387a},
+ {"ricoh,rs5c372a", rtc_rs5c372a},
+ {"ricoh,rs5c372b", rtc_rs5c372b},
+ {"ricoh,rv5c386", rtc_rv5c386},
+ {"ricoh,rv5c387a", rtc_rv5c387a},
+ {},
+};
+MODULE_DEVICE_TABLE(i2c, rs5c372_id);
+
/* REVISIT: this assumes that:
* - we're in the 21st century, so it's safe to ignore the century
* bit for rv5c38[67] (REG_MONTH bit 7);
@@ -494,7 +507,7 @@ static void rs5c_sysfs_unregister(struct device *dev)
static struct i2c_driver rs5c372_driver;
-static int rs5c372_probe(struct i2c_client *client)
+static int rs5c372_probe(struct i2c_client *client, const struct i2c_device_id *id)
{
int err = 0;
struct rs5c372 *rs5c372;
@@ -522,18 +535,7 @@ static int rs5c372_probe(struct i2c_client *client)
if (err < 0)
goto exit_kfree;
- if (strcmp(client->name, "rs5c372a") == 0)
- rs5c372->type = rtc_rs5c372a;
- else if (strcmp(client->name, "rs5c372b") == 0)
- rs5c372->type = rtc_rs5c372b;
- else if (strcmp(client->name, "rv5c386") == 0)
- rs5c372->type = rtc_rv5c386;
- else if (strcmp(client->name, "rv5c387a") == 0)
- rs5c372->type = rtc_rv5c387a;
- else {
- rs5c372->type = rtc_rs5c372b;
- dev_warn(&client->dev, "assuming rs5c372b\n");
- }
+ rs5c372->type = id->driver_data;
/* clock may be set for am/pm or 24 hr time */
switch (rs5c372->type) {
@@ -651,6 +653,7 @@ static struct i2c_driver rs5c372_driver = {
},
.probe = rs5c372_probe,
.remove = rs5c372_remove,
+ .id_table = rs5c372_id,
};
static __init int rs5c372_init(void)
^ permalink raw reply related
* [PATCH 3/5] Clean up error returns
From: Jon Smirl @ 2007-12-10 18:33 UTC (permalink / raw)
To: i2c, linuxppc-dev
In-Reply-To: <20071210183323.12584.88127.stgit@terra.home>
Return errors that were being ignored in the mpc-i2c driver
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
---
drivers/i2c/busses/i2c-mpc.c | 30 +++++++++++++++++-------------
1 files changed, 17 insertions(+), 13 deletions(-)
diff --git a/drivers/i2c/busses/i2c-mpc.c b/drivers/i2c/busses/i2c-mpc.c
index d8de4ac..7c35a8f 100644
--- a/drivers/i2c/busses/i2c-mpc.c
+++ b/drivers/i2c/busses/i2c-mpc.c
@@ -180,7 +180,7 @@ static void mpc_i2c_stop(struct mpc_i2c *i2c)
static int mpc_write(struct mpc_i2c *i2c, int target,
const u8 * data, int length, int restart)
{
- int i;
+ int i, result;
unsigned timeout = i2c->adap.timeout;
u32 flags = restart ? CCR_RSTA : 0;
@@ -192,15 +192,17 @@ static int mpc_write(struct mpc_i2c *i2c, int target,
/* Write target byte */
writeb((target << 1), i2c->base + MPC_I2C_DR);
- if (i2c_wait(i2c, timeout, 1) < 0)
- return -1;
+ result = i2c_wait(i2c, timeout, 1);
+ if (result < 0)
+ return result;
for (i = 0; i < length; i++) {
/* Write data byte */
writeb(data[i], i2c->base + MPC_I2C_DR);
- if (i2c_wait(i2c, timeout, 1) < 0)
- return -1;
+ result = i2c_wait(i2c, timeout, 1);
+ if (result < 0)
+ return result;
}
return 0;
@@ -210,7 +212,7 @@ static int mpc_read(struct mpc_i2c *i2c, int target,
u8 * data, int length, int restart)
{
unsigned timeout = i2c->adap.timeout;
- int i;
+ int i, result;
u32 flags = restart ? CCR_RSTA : 0;
/* Start with MEN */
@@ -221,8 +223,9 @@ static int mpc_read(struct mpc_i2c *i2c, int target,
/* Write target address byte - this time with the read flag set */
writeb((target << 1) | 1, i2c->base + MPC_I2C_DR);
- if (i2c_wait(i2c, timeout, 1) < 0)
- return -1;
+ result = i2c_wait(i2c, timeout, 1);
+ if (result < 0)
+ return result;
if (length) {
if (length == 1)
@@ -234,8 +237,9 @@ static int mpc_read(struct mpc_i2c *i2c, int target,
}
for (i = 0; i < length; i++) {
- if (i2c_wait(i2c, timeout, 0) < 0)
- return -1;
+ result = i2c_wait(i2c, timeout, 0);
+ if (result < 0)
+ return result;
/* Generate txack on next to last byte */
if (i == length - 2)
@@ -321,9 +325,9 @@ static int fsl_i2c_probe(struct platform_device *pdev)
pdata = (struct fsl_i2c_platform_data *) pdev->dev.platform_data;
- if (!(i2c = kzalloc(sizeof(*i2c), GFP_KERNEL))) {
+ i2c = kzalloc(sizeof(*i2c), GFP_KERNEL);
+ if (!i2c)
return -ENOMEM;
- }
i2c->irq = platform_get_irq(pdev, 0);
if (i2c->irq < 0) {
@@ -381,7 +385,7 @@ static int fsl_i2c_remove(struct platform_device *pdev)
i2c_del_adapter(&i2c->adap);
platform_set_drvdata(pdev, NULL);
- if (i2c->irq != 0)
+ if (i2c->irq != NO_IRQ)
free_irq(i2c->irq, i2c);
iounmap(i2c->base);
^ permalink raw reply related
* [PATCH 1/5] Implement module aliasing for i2c to translate from device tree names
From: Jon Smirl @ 2007-12-10 18:33 UTC (permalink / raw)
To: i2c, linuxppc-dev
In-Reply-To: <20071210183323.12584.88127.stgit@terra.home>
This patch allows new style i2c chip drivers to have alias names using
the official kernel aliasing system and MODULE_DEVICE_TABLE(). I've
tested it on PowerPC and x86. This change is required for PowerPC
device tree support.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
---
drivers/i2c/i2c-core.c | 34 +++++++++++++++++++++++++++-------
include/linux/i2c.h | 5 ++---
include/linux/mod_devicetable.h | 9 +++++++++
3 files changed, 38 insertions(+), 10 deletions(-)
diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c
index b5e13e4..6fa6bab 100644
--- a/drivers/i2c/i2c-core.c
+++ b/drivers/i2c/i2c-core.c
@@ -47,10 +47,26 @@ static DEFINE_IDR(i2c_adapter_idr);
/* ------------------------------------------------------------------------- */
-static int i2c_device_match(struct device *dev, struct device_driver *drv)
+static const struct i2c_device_id *i2c_device_match(const struct i2c_device_id *id, struct i2c_client *client)
+{
+ /* new style drivers use the same kind of driver matching policy
+ * as platform devices or SPI: compare device and driver IDs.
+ */
+ if (id) {
+ while (id->name[0]) {
+ if (strcmp(client->driver_name, id->name) == 0)
+ return id;
+ id++;
+ }
+ }
+ return NULL;
+}
+
+static int i2c_bus_match(struct device *dev, struct device_driver *drv)
{
struct i2c_client *client = to_i2c_client(dev);
struct i2c_driver *driver = to_i2c_driver(drv);
+ const struct i2c_device_id *found_id;
/* make legacy i2c drivers bypass driver model probing entirely;
* such drivers scan each i2c adapter/bus themselves.
@@ -58,10 +74,11 @@ static int i2c_device_match(struct device *dev, struct device_driver *drv)
if (!is_newstyle_driver(driver))
return 0;
- /* new style drivers use the same kind of driver matching policy
- * as platform devices or SPI: compare device and driver IDs.
- */
- return strcmp(client->driver_name, drv->name) == 0;
+ found_id = i2c_device_match(driver->id_table, client);
+ if (found_id)
+ return 1;
+
+ return 0;
}
#ifdef CONFIG_HOTPLUG
@@ -89,12 +106,15 @@ static int i2c_device_probe(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct i2c_driver *driver = to_i2c_driver(dev->driver);
+ const struct i2c_device_id *id;
if (!driver->probe)
return -ENODEV;
client->driver = driver;
dev_dbg(dev, "probe\n");
- return driver->probe(client);
+
+ id = i2c_device_match(driver->id_table, client);
+ return driver->probe(client, id);
}
static int i2c_device_remove(struct device *dev)
@@ -189,7 +209,7 @@ static struct device_attribute i2c_dev_attrs[] = {
static struct bus_type i2c_bus_type = {
.name = "i2c",
.dev_attrs = i2c_dev_attrs,
- .match = i2c_device_match,
+ .match = i2c_bus_match,
.uevent = i2c_device_uevent,
.probe = i2c_device_probe,
.remove = i2c_device_remove,
diff --git a/include/linux/i2c.h b/include/linux/i2c.h
index a100c9f..0ca1a59 100644
--- a/include/linux/i2c.h
+++ b/include/linux/i2c.h
@@ -126,7 +126,7 @@ struct i2c_driver {
* With the driver model, device enumeration is NEVER done by drivers;
* it's done by infrastructure. (NEW STYLE DRIVERS ONLY)
*/
- int (*probe)(struct i2c_client *);
+ int (*probe)(struct i2c_client *, const struct i2c_device_id *id);
int (*remove)(struct i2c_client *);
/* driver model interfaces that don't relate to enumeration */
@@ -141,11 +141,10 @@ struct i2c_driver {
struct device_driver driver;
struct list_head list;
+ struct i2c_device_id *id_table;
};
#define to_i2c_driver(d) container_of(d, struct i2c_driver, driver)
-#define I2C_NAME_SIZE 20
-
/**
* struct i2c_client - represent an I2C slave device
* @flags: I2C_CLIENT_TEN indicates the device uses a ten bit chip address;
diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h
index e9fddb4..688fad6 100644
--- a/include/linux/mod_devicetable.h
+++ b/include/linux/mod_devicetable.h
@@ -367,4 +367,13 @@ struct virtio_device_id {
};
#define VIRTIO_DEV_ANY_ID 0xffffffff
+/* i2c */
+
+#define I2C_NAME_SIZE 40
+struct i2c_device_id {
+ char name[I2C_NAME_SIZE];
+ kernel_ulong_t driver_data; /* Data private to the driver */
+};
+
+
#endif /* LINUX_MOD_DEVICETABLE_H */
^ permalink raw reply related
* [PATCH 5/5] Convert pfc8563 i2c driver from old style to new style
From: Jon Smirl @ 2007-12-10 18:33 UTC (permalink / raw)
To: i2c, linuxppc-dev
In-Reply-To: <20071210183323.12584.88127.stgit@terra.home>
Convert pfc8563 i2c driver from old style to new style. The
driver is also modified to support device tree names via the
i2c mod alias mechanism.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
---
drivers/rtc/rtc-pcf8563.c | 110 ++++++++++++---------------------------------
1 files changed, 30 insertions(+), 80 deletions(-)
diff --git a/drivers/rtc/rtc-pcf8563.c b/drivers/rtc/rtc-pcf8563.c
index 0242d80..7da2cd0 100644
--- a/drivers/rtc/rtc-pcf8563.c
+++ b/drivers/rtc/rtc-pcf8563.c
@@ -25,10 +25,6 @@
* located at 0x51 will pass the validation routine due to
* the way the registers are implemented.
*/
-static unsigned short normal_i2c[] = { I2C_CLIENT_END };
-
-/* Module parameters */
-I2C_CLIENT_INSMOD;
#define PCF8563_REG_ST1 0x00 /* status */
#define PCF8563_REG_ST2 0x01
@@ -72,9 +68,6 @@ struct pcf8563 {
int c_polarity; /* 0: MO_C=1 means 19xx, otherwise MO_C=1 means 20xx */
};
-static int pcf8563_probe(struct i2c_adapter *adapter, int address, int kind);
-static int pcf8563_detach(struct i2c_client *client);
-
/*
* In the routines that deal directly with the pcf8563 hardware, we use
* rtc_time -- month 0-11, hour 0-23, yr = calendar year-epoch.
@@ -257,98 +250,55 @@ static const struct rtc_class_ops pcf8563_rtc_ops = {
.set_time = pcf8563_rtc_set_time,
};
-static int pcf8563_attach(struct i2c_adapter *adapter)
+static int pcf8563_remove(struct i2c_client *client)
{
- return i2c_probe(adapter, &addr_data, pcf8563_probe);
+ struct rtc_device *rtc = i2c_get_clientdata(client);
+
+ if (rtc)
+ rtc_device_unregister(rtc);
+
+ return 0;
}
+static struct i2c_device_id pcf8563_id[] = {
+ {"rtc-pcf8563", 0},
+ {"pcf8563", 0},
+ {"philips,pcf8563", 0},
+ {"rtc8564", 0},
+ {"epson,rtc8564", 0},
+ {},
+};
+MODULE_DEVICE_TABLE(i2c, pcf8563_id);
+
+static int pcf8563_probe(struct i2c_client *client, const struct i2c_device_id *id);
+
static struct i2c_driver pcf8563_driver = {
.driver = {
- .name = "pcf8563",
+ .name = "rtc-pcf8563",
},
.id = I2C_DRIVERID_PCF8563,
- .attach_adapter = &pcf8563_attach,
- .detach_client = &pcf8563_detach,
+ .probe = &pcf8563_probe,
+ .remove = &pcf8563_remove,
+ .id_table = pcf8563_id,
};
-static int pcf8563_probe(struct i2c_adapter *adapter, int address, int kind)
+static int pcf8563_probe(struct i2c_client *client, const struct i2c_device_id *id)
{
- struct pcf8563 *pcf8563;
- struct i2c_client *client;
+ int result;
struct rtc_device *rtc;
- int err = 0;
-
- dev_dbg(&adapter->dev, "%s\n", __FUNCTION__);
-
- if (!i2c_check_functionality(adapter, I2C_FUNC_I2C)) {
- err = -ENODEV;
- goto exit;
- }
-
- if (!(pcf8563 = kzalloc(sizeof(struct pcf8563), GFP_KERNEL))) {
- err = -ENOMEM;
- goto exit;
- }
-
- client = &pcf8563->client;
- client->addr = address;
- client->driver = &pcf8563_driver;
- client->adapter = adapter;
-
- strlcpy(client->name, pcf8563_driver.driver.name, I2C_NAME_SIZE);
-
- /* Verify the chip is really an PCF8563 */
- if (kind < 0) {
- if (pcf8563_validate_client(client) < 0) {
- err = -ENODEV;
- goto exit_kfree;
- }
- }
-
- /* Inform the i2c layer */
- if ((err = i2c_attach_client(client)))
- goto exit_kfree;
-
- dev_info(&client->dev, "chip found, driver version " DRV_VERSION "\n");
+ result = pcf8563_validate_client(client);
+ if (result)
+ return result;
rtc = rtc_device_register(pcf8563_driver.driver.name, &client->dev,
&pcf8563_rtc_ops, THIS_MODULE);
-
- if (IS_ERR(rtc)) {
- err = PTR_ERR(rtc);
- goto exit_detach;
- }
+ if (IS_ERR(rtc))
+ return PTR_ERR(rtc);
i2c_set_clientdata(client, rtc);
return 0;
-
-exit_detach:
- i2c_detach_client(client);
-
-exit_kfree:
- kfree(pcf8563);
-
-exit:
- return err;
-}
-
-static int pcf8563_detach(struct i2c_client *client)
-{
- struct pcf8563 *pcf8563 = container_of(client, struct pcf8563, client);
- int err;
- struct rtc_device *rtc = i2c_get_clientdata(client);
-
- if (rtc)
- rtc_device_unregister(rtc);
-
- if ((err = i2c_detach_client(client)))
- return err;
-
- kfree(pcf8563);
-
- return 0;
}
static int __init pcf8563_init(void)
^ permalink raw reply related
* [PATCH 4/5] Convert PowerPC MPC i2c to of_platform_driver from platform_driver
From: Jon Smirl @ 2007-12-10 18:33 UTC (permalink / raw)
To: i2c, linuxppc-dev
In-Reply-To: <20071210183323.12584.88127.stgit@terra.home>
Convert MPC i2c driver from being a platform_driver to an open firmware version. Error returns were improved. Routine names were changed from fsl_ to mpc_ to make them match the file name.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
---
arch/powerpc/sysdev/fsl_soc.c | 96 -------------------------
drivers/i2c/busses/i2c-mpc.c | 158 +++++++++++++++++++++++++++++------------
2 files changed, 110 insertions(+), 144 deletions(-)
diff --git a/arch/powerpc/sysdev/fsl_soc.c b/arch/powerpc/sysdev/fsl_soc.c
index 268638a..d6ef264 100644
--- a/arch/powerpc/sysdev/fsl_soc.c
+++ b/arch/powerpc/sysdev/fsl_soc.c
@@ -318,102 +318,6 @@ err:
arch_initcall(gfar_of_init);
-#ifdef CONFIG_I2C_BOARDINFO
-#include <linux/i2c.h>
-
-static void __init of_register_i2c_devices(struct device_node *adap_node,
- int bus_num)
-{
- struct device_node *node = NULL;
- const char *compatible;
-
- while ((node = of_get_next_child(adap_node, node))) {
- struct i2c_board_info info = {};
- const u32 *addr;
- int len;
-
- addr = of_get_property(node, "reg", &len);
- if (!addr || len < sizeof(int) || *addr > (1 << 10) - 1) {
- printk(KERN_WARNING "fsl_soc.c: invalid i2c device entry\n");
- continue;
- }
-
- info.irq = irq_of_parse_and_map(node, 0);
- if (info.irq == NO_IRQ)
- info.irq = -1;
-
- compatible = of_get_property(node, "compatible", &len);
- if (!compatible) {
- printk(KERN_WARNING "i2c-mpc.c: invalid entry, missing compatible attribute\n");
- continue;
- }
- strncpy(info.driver_name, compatible, sizeof(info.driver_name));
-
- info.addr = *addr;
-
- i2c_register_board_info(bus_num, &info, 1);
- }
-}
-
-static int __init fsl_i2c_of_init(void)
-{
- struct device_node *np;
- unsigned int i;
- struct platform_device *i2c_dev;
- int ret;
-
- for (np = NULL, i = 0;
- (np = of_find_compatible_node(np, "i2c", "fsl-i2c")) != NULL;
- i++) {
- struct resource r[2];
- struct fsl_i2c_platform_data i2c_data;
- const unsigned char *flags = NULL;
-
- memset(&r, 0, sizeof(r));
- memset(&i2c_data, 0, sizeof(i2c_data));
-
- ret = of_address_to_resource(np, 0, &r[0]);
- if (ret)
- goto err;
-
- of_irq_to_resource(np, 0, &r[1]);
-
- i2c_dev = platform_device_register_simple("fsl-i2c", i, r, 2);
- if (IS_ERR(i2c_dev)) {
- ret = PTR_ERR(i2c_dev);
- goto err;
- }
-
- i2c_data.device_flags = 0;
- flags = of_get_property(np, "dfsrr", NULL);
- if (flags)
- i2c_data.device_flags |= FSL_I2C_DEV_SEPARATE_DFSRR;
-
- flags = of_get_property(np, "fsl5200-clocking", NULL);
- if (flags)
- i2c_data.device_flags |= FSL_I2C_DEV_CLOCK_5200;
-
- ret =
- platform_device_add_data(i2c_dev, &i2c_data,
- sizeof(struct
- fsl_i2c_platform_data));
- if (ret)
- goto unreg;
-
- of_register_i2c_devices(np, i);
- }
-
- return 0;
-
-unreg:
- platform_device_unregister(i2c_dev);
-err:
- return ret;
-}
-
-arch_initcall(fsl_i2c_of_init);
-#endif
-
#ifdef CONFIG_PPC_83xx
static int __init mpc83xx_wdt_init(void)
{
diff --git a/drivers/i2c/busses/i2c-mpc.c b/drivers/i2c/busses/i2c-mpc.c
index 7c35a8f..6f080d4 100644
--- a/drivers/i2c/busses/i2c-mpc.c
+++ b/drivers/i2c/busses/i2c-mpc.c
@@ -17,7 +17,7 @@
#include <linux/module.h>
#include <linux/sched.h>
#include <linux/init.h>
-#include <linux/platform_device.h>
+#include <linux/of_platform.h>
#include <asm/io.h>
#include <linux/fsl_devices.h>
@@ -25,13 +25,13 @@
#include <linux/interrupt.h>
#include <linux/delay.h>
-#define MPC_I2C_ADDR 0x00
+#define DRV_NAME "mpc-i2c"
+
#define MPC_I2C_FDR 0x04
#define MPC_I2C_CR 0x08
#define MPC_I2C_SR 0x0c
#define MPC_I2C_DR 0x10
#define MPC_I2C_DFSRR 0x14
-#define MPC_I2C_REGION 0x20
#define CCR_MEN 0x80
#define CCR_MIEN 0x40
@@ -316,105 +316,167 @@ static struct i2c_adapter mpc_ops = {
.retries = 1
};
-static int fsl_i2c_probe(struct platform_device *pdev)
+struct i2c_driver_device {
+ char *of_device;
+ char *i2c_driver;
+ char *i2c_type;
+};
+
+static void of_register_i2c_devices(struct i2c_adapter *adap, struct device_node *adap_node)
+{
+ struct device_node *node = NULL;
+
+ while ((node = of_get_next_child(adap_node, node))) {
+ struct i2c_board_info info;
+ const u32 *addr;
+ const char *compatible;
+ int len;
+
+ addr = of_get_property(node, "reg", &len);
+ if (!addr || len < sizeof(int) || *addr > (1 << 10) - 1) {
+ printk(KERN_ERR "i2c-mpc.c: invalid entry, missing reg attribute\n");
+ continue;
+ }
+
+ info.irq = irq_of_parse_and_map(node, 0);
+ if (info.irq == NO_IRQ)
+ info.irq = -1;
+
+ compatible = of_get_property(node, "compatible", &len);
+ if (!compatible) {
+ printk(KERN_ERR "i2c-mpc.c: invalid entry, missing compatible attribute\n");
+ continue;
+ }
+ strncpy(info.driver_name, compatible, sizeof(info.driver_name));
+ info.type[0] = '\0';
+
+ info.platform_data = NULL;
+ info.addr = *addr;
+
+ if (!i2c_new_device(adap, &info)) {
+ printk(KERN_ERR "i2c-mpc.c: Failed to load driver for %s\n", info.driver_name);
+ continue;
+ }
+ }
+}
+
+static int mpc_i2c_probe(struct of_device *op, const struct of_device_id *match)
{
int result = 0;
struct mpc_i2c *i2c;
- struct fsl_i2c_platform_data *pdata;
- struct resource *r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-
- pdata = (struct fsl_i2c_platform_data *) pdev->dev.platform_data;
i2c = kzalloc(sizeof(*i2c), GFP_KERNEL);
if (!i2c)
return -ENOMEM;
- i2c->irq = platform_get_irq(pdev, 0);
- if (i2c->irq < 0) {
- result = -ENXIO;
- goto fail_get_irq;
- }
- i2c->flags = pdata->device_flags;
- init_waitqueue_head(&i2c->queue);
+ if (of_get_property(op->node, "dfsrr", NULL))
+ i2c->flags |= FSL_I2C_DEV_SEPARATE_DFSRR;
- i2c->base = ioremap((phys_addr_t)r->start, MPC_I2C_REGION);
+ if (of_device_is_compatible(op->node, "mpc5200-i2c"))
+ i2c->flags |= FSL_I2C_DEV_CLOCK_5200;
+ init_waitqueue_head(&i2c->queue);
+
+ i2c->base = of_iomap(op->node, 0);
if (!i2c->base) {
printk(KERN_ERR "i2c-mpc - failed to map controller\n");
result = -ENOMEM;
goto fail_map;
}
- if (i2c->irq != 0)
- if ((result = request_irq(i2c->irq, mpc_i2c_isr,
- IRQF_SHARED, "i2c-mpc", i2c)) < 0) {
- printk(KERN_ERR
- "i2c-mpc - failed to attach interrupt\n");
- goto fail_irq;
- }
+ i2c->irq = irq_of_parse_and_map(op->node, 0);
+ if (i2c->irq == NO_IRQ) {
+ result = -ENXIO;
+ goto fail_irq;
+ }
+
+ result = request_irq(i2c->irq, mpc_i2c_isr, IRQF_SHARED, "i2c-mpc", i2c));
+ if (result < 0) {
+ printk(KERN_ERR "i2c-mpc - failed to attach interrupt\n");
+ goto fail_request;
+ }
mpc_i2c_setclock(i2c);
- platform_set_drvdata(pdev, i2c);
+
+ dev_set_drvdata(&op->dev, i2c);
i2c->adap = mpc_ops;
- i2c->adap.nr = pdev->id;
i2c_set_adapdata(&i2c->adap, i2c);
- i2c->adap.dev.parent = &pdev->dev;
- if ((result = i2c_add_numbered_adapter(&i2c->adap)) < 0) {
+ i2c->adap.dev.parent = &op->dev;
+
+ result = i2c_add_adapter(&i2c->adap);
+ if (result < 0) {
printk(KERN_ERR "i2c-mpc - failed to add adapter\n");
goto fail_add;
}
+ of_register_i2c_devices(&i2c->adap, op->node);
+
return result;
- fail_add:
- if (i2c->irq != 0)
- free_irq(i2c->irq, i2c);
- fail_irq:
+fail_add:
+ free_irq(i2c->irq, i2c);
+fail_request:
+ irq_dispose_mapping(i2c->irq);
+fail_irq:
iounmap(i2c->base);
- fail_map:
- fail_get_irq:
+fail_map:
kfree(i2c);
return result;
};
-static int fsl_i2c_remove(struct platform_device *pdev)
+static int mpc_i2c_remove(struct of_device *op)
{
- struct mpc_i2c *i2c = platform_get_drvdata(pdev);
+ struct mpc_i2c *i2c = dev_get_drvdata(&op->dev);
i2c_del_adapter(&i2c->adap);
- platform_set_drvdata(pdev, NULL);
+ dev_set_drvdata(&op->dev, NULL);
if (i2c->irq != NO_IRQ)
free_irq(i2c->irq, i2c);
+ irq_dispose_mapping(i2c->irq);
iounmap(i2c->base);
kfree(i2c);
return 0;
};
+static struct of_device_id mpc_i2c_of_match[] = {
+ {
+ .compatible = "fsl-i2c",
+ },
+};
+MODULE_DEVICE_TABLE(of, mpc_i2c_of_match);
+
+
/* Structure for a device driver */
-static struct platform_driver fsl_i2c_driver = {
- .probe = fsl_i2c_probe,
- .remove = fsl_i2c_remove,
- .driver = {
- .owner = THIS_MODULE,
- .name = "fsl-i2c",
+static struct of_platform_driver mpc_i2c_driver = {
+ .match_table = mpc_i2c_of_match,
+ .probe = mpc_i2c_probe,
+ .remove = __devexit_p(mpc_i2c_remove),
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = DRV_NAME,
},
};
-static int __init fsl_i2c_init(void)
+static int __init mpc_i2c_init(void)
{
- return platform_driver_register(&fsl_i2c_driver);
+ int rv;
+
+ rv = of_register_platform_driver(&mpc_i2c_driver);
+ if (rv)
+ printk(KERN_ERR DRV_NAME " of_register_platform_driver failed (%i)\n", rv);
+ return rv;
}
-static void __exit fsl_i2c_exit(void)
+static void __exit mpc_i2c_exit(void)
{
- platform_driver_unregister(&fsl_i2c_driver);
+ of_unregister_platform_driver(&mpc_i2c_driver);
}
-module_init(fsl_i2c_init);
-module_exit(fsl_i2c_exit);
+module_init(mpc_i2c_init);
+module_exit(mpc_i2c_exit);
MODULE_AUTHOR("Adrian Cox <adrian@humboldt.co.uk>");
MODULE_DESCRIPTION
^ permalink raw reply related
* [PATCH 0/5] Series to add device tree naming to i2c
From: Jon Smirl @ 2007-12-10 18:33 UTC (permalink / raw)
To: i2c, linuxppc-dev
Respin to split error return fixups out of mpc-i2c to of_platform change
The following series implements standard linux module aliasing for i2c modules
It then converts the mpc i2c driver from being a platform driver to an open
firmware one. I2C device names are picked up from the device tree. Module
aliasing is used to translate from device tree names into to linux kernel
names. Several i2c drivers are updated to use the new aliasing.
--
Jon Smirl
jonsmirl@gmail.com
^ permalink raw reply
* Re: [i2c] [PATCH 0/4] Series to add device tree naming to i2c
From: Scott Wood @ 2007-12-10 18:37 UTC (permalink / raw)
To: Jon Smirl; +Cc: Jean Delvare, i2c, linuxppc-dev
In-Reply-To: <9e4733910712101006s37829df4w676eea54a98b282d@mail.gmail.com>
Jon Smirl wrote:
> I can't see an easy way to do this. The basic problem is that the i2c
> drivers are assumed to be cross platform.
It'd be a small binding-specific portion, similar to an of_platform stub
on a generic driver. It could probably wait until an actual need
arises, though.
> I would need to add a path through the i2c core for getting a void
> pointer from the bus to the device But then when the device code gets
> this pointer it has no way of knowing what it was.
It'd need to know which binding/name combination it matched against
(similar to how of_platform does it).
> Another way that would work cross platform would be for the module to
> have module parameters for the extra attributes.
Ick. Module parameters are a PITA, and have to be duplicated with
command line parameters if you want to support non-modular builds.
-Scott
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox