* Re: [PATCH v5] qe: add ability to upload QE firmware
From: Arnd Bergmann @ 2007-12-12 22:05 UTC (permalink / raw)
To: linuxppc-dev; +Cc: Timur Tabi
In-Reply-To: <11970422334145-git-send-email-timur@freescale.com>
On Friday 07 December 2007, Timur Tabi wrote:
> Define the layout of a binary blob that contains a QE firmware and instru=
ctions
> on how to upload it. =A0Add function qe_upload_firmware() to parse the bl=
ob
> and perform the actual upload. =A0Fully define 'struct rsp' in immap_qe.h=
to
> include the actual RISC Special Registers. =A0Added description of a new
> QE firmware node to booting-without-of.txt.
All the comments I had were addressed, mostly by convincing me that the
code was correct to start with, so
> Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
^ permalink raw reply
* Re: [PATCH/RFC] CPM1: implement GPIO API
From: Arnd Bergmann @ 2007-12-12 22:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <47600F5E.8060907@scram.de>
On Wednesday 12 December 2007, Jochen Friedrich wrote:
> +static spinlock_t *cpm1_port_locks;
> +static int cpm1_num_ports;
Having an array of spinlocks is rather unusual and normally not necessary.
Did you measure a significant performance impact by using a global lock
for all ports?
If not, I would recommend simplifying this.
> +EXPORT_SYMBOL_GPL(gpio_request);
> +EXPORT_SYMBOL_GPL(gpio_direction_input);
> +EXPORT_SYMBOL_GPL(gpio_direction_output);
> +EXPORT_SYMBOL_GPL(gpio_get_value);
> +EXPORT_SYMBOL_GPL(gpio_set_value);
All these function names are rather generic identifiers, but you export them
from a platform specific file. I'd say they should either have a more specific
name space (e.g. cpm1_gpio_request), or should be implemented in a more
generic way.
Arnd <><
^ permalink raw reply
* [PATCH v2 5/8] mpc83xx: Power Management support
From: Scott Wood @ 2007-12-12 22:41 UTC (permalink / raw)
To: paulus; +Cc: linuxppc-dev
Basic PM support for 83xx. Standby is implemented as sleep.
Suspend-to-RAM is implemented as "deep sleep" (with the processor
turned off) on 831x.
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
The enabling of i-cache at the end of the suspend code somehow fell off of
the code that was sent out in the previous patch (it still works when
booting high, which is what I tested, but not booting low).
The rest of the patchset stays the same.
arch/powerpc/platforms/83xx/Kconfig | 5 +
arch/powerpc/platforms/83xx/Makefile | 1 +
arch/powerpc/platforms/83xx/suspend-asm.S | 539 +++++++++++++++++++++++++++++
arch/powerpc/platforms/83xx/suspend.c | 423 ++++++++++++++++++++++
arch/powerpc/sysdev/fsl_soc.c | 33 ++
arch/powerpc/sysdev/fsl_soc.h | 10 +
arch/powerpc/sysdev/ipic.c | 71 ++++
include/asm-powerpc/reg.h | 4 +
include/linux/fsl_devices.h | 24 ++
9 files changed, 1110 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/platforms/83xx/suspend-asm.S
create mode 100644 arch/powerpc/platforms/83xx/suspend.c
diff --git a/arch/powerpc/platforms/83xx/Kconfig b/arch/powerpc/platforms/83xx/Kconfig
index ec305f1..901dbaf 100644
--- a/arch/powerpc/platforms/83xx/Kconfig
+++ b/arch/powerpc/platforms/83xx/Kconfig
@@ -75,3 +75,8 @@ config PPC_MPC836x
select PPC_UDBG_16550
select PPC_INDIRECT_PCI
default y if MPC836x_MDS
+
+config PPC_83xx_SUSPEND
+ bool
+ default y
+ depends on PPC_83xx && SUSPEND
diff --git a/arch/powerpc/platforms/83xx/Makefile b/arch/powerpc/platforms/83xx/Makefile
index 5a98f88..944369e 100644
--- a/arch/powerpc/platforms/83xx/Makefile
+++ b/arch/powerpc/platforms/83xx/Makefile
@@ -3,6 +3,7 @@
#
obj-y := misc.o usb.o
obj-$(CONFIG_PCI) += pci.o
+obj-$(CONFIG_SUSPEND) += suspend.o suspend-asm.o
obj-$(CONFIG_MPC8313_RDB) += mpc8313_rdb.o
obj-$(CONFIG_MPC832x_RDB) += mpc832x_rdb.o
obj-$(CONFIG_MPC834x_MDS) += mpc834x_mds.o
diff --git a/arch/powerpc/platforms/83xx/suspend-asm.S b/arch/powerpc/platforms/83xx/suspend-asm.S
new file mode 100644
index 0000000..03e29a2
--- /dev/null
+++ b/arch/powerpc/platforms/83xx/suspend-asm.S
@@ -0,0 +1,539 @@
+/*
+ * Enter and leave sleep state on MPC83xx
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2006 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <asm/page.h>
+#include <asm/ppc_asm.h>
+#include <asm/reg.h>
+#include <asm/asm-offsets.h>
+
+#define SS_MEMSAVE 0x00
+#define SS_HID 0x08 /* 3 HIDs */
+#define SS_IABR 0x14 /* 2 IABRs */
+#define SS_IBCR 0x1c
+#define SS_DABR 0x20 /* 2 DABRs */
+#define SS_DBCR 0x28
+#define SS_SP 0x2c
+#define SS_SR 0x30 /* 16 segment registers */
+#define SS_CURRENT 0x70
+#define SS_MSR 0x74
+#define SS_SDR1 0x78
+#define SS_LR 0x7c
+#define SS_SPRG 0x80 /* 4 SPRGs */
+#define SS_DBAT 0x90 /* 8 DBATs */
+#define SS_IBAT 0xd0 /* 8 IBATs */
+#define SS_TB 0x110
+#define SS_CR 0x118
+#define SS_GPREG 0x11c /* r12-r31 */
+#define STATE_SAVE_SIZE 0x16c
+
+ .section .data
+ .align 5
+
+mpc83xx_sleep_save_area:
+ .space STATE_SAVE_SIZE
+immrbase:
+ .long 0
+
+ .section .text
+ .align 5
+
+ /* r3 = physical address of IMMR */
+_GLOBAL(mpc83xx_enter_deep_sleep)
+ /* Re-use the state saving/restoring code in
+ * arch/powerpc/kernel/swsusp_32.S, but have
+ * it call us instead of swsusp_save.
+ */
+
+ lis r4, immrbase@ha
+ stw r3, immrbase@l(r4)
+
+ /* The first 2 words of memory are used to communicate with the
+ * bootloader, to tell it how to resume.
+ *
+ * The first word is the magic number 0xf5153ae5, and the second
+ * is the pointer to mpc83xx_deep_resume.
+ *
+ * The original content of these two words is saved in the state
+ * save area.
+ */
+
+ lis r3, mpc83xx_sleep_save_area@h
+ ori r3, r3, mpc83xx_sleep_save_area@l
+
+ lis r4, KERNELBASE@h
+ lwz r5, 0(r4)
+ lwz r6, 4(r4)
+
+ stw r5, SS_MEMSAVE+0(r3)
+ stw r6, SS_MEMSAVE+4(r3)
+
+ mfspr r5, SPRN_HID0
+ mfspr r6, SPRN_HID1
+ mfspr r7, SPRN_HID2
+
+ stw r5, SS_HID+0(r3)
+ stw r6, SS_HID+4(r3)
+ stw r7, SS_HID+8(r3)
+
+ mfspr r4, SPRN_IABR
+ mfspr r5, SPRN_IABR2
+ mfspr r6, SPRN_IBCR
+ mfspr r7, SPRN_DABR
+ mfspr r8, SPRN_DABR2
+ mfspr r9, SPRN_DBCR
+
+ stw r4, SS_IABR+0(r3)
+ stw r5, SS_IABR+4(r3)
+ stw r6, SS_IBCR(r3)
+ stw r7, SS_DABR+0(r3)
+ stw r8, SS_DABR+4(r3)
+ stw r9, SS_DBCR(r3)
+
+ mfspr r4, SPRN_SPRG0
+ mfspr r5, SPRN_SPRG1
+ mfspr r6, SPRN_SPRG2
+ mfspr r7, SPRN_SPRG3
+ mfsdr1 r8
+
+ stw r4, SS_SPRG+0(r3)
+ stw r5, SS_SPRG+4(r3)
+ stw r6, SS_SPRG+8(r3)
+ stw r7, SS_SPRG+12(r3)
+ stw r8, SS_SDR1(r3)
+
+ mfspr r4, SPRN_DBAT0U
+ mfspr r5, SPRN_DBAT0L
+ mfspr r6, SPRN_DBAT1U
+ mfspr r7, SPRN_DBAT1L
+
+ stw r4, SS_DBAT+0x00(r3)
+ stw r5, SS_DBAT+0x04(r3)
+ stw r6, SS_DBAT+0x08(r3)
+ stw r7, SS_DBAT+0x0c(r3)
+
+ mfspr r4, SPRN_DBAT2U
+ mfspr r5, SPRN_DBAT2L
+ mfspr r6, SPRN_DBAT3U
+ mfspr r7, SPRN_DBAT3L
+
+ stw r4, SS_DBAT+0x10(r3)
+ stw r5, SS_DBAT+0x14(r3)
+ stw r6, SS_DBAT+0x18(r3)
+ stw r7, SS_DBAT+0x1c(r3)
+
+ mfspr r4, SPRN_DBAT4U
+ mfspr r5, SPRN_DBAT4L
+ mfspr r6, SPRN_DBAT5U
+ mfspr r7, SPRN_DBAT5L
+
+ stw r4, SS_DBAT+0x20(r3)
+ stw r5, SS_DBAT+0x24(r3)
+ stw r6, SS_DBAT+0x28(r3)
+ stw r7, SS_DBAT+0x2c(r3)
+
+ mfspr r4, SPRN_DBAT6U
+ mfspr r5, SPRN_DBAT6L
+ mfspr r6, SPRN_DBAT7U
+ mfspr r7, SPRN_DBAT7L
+
+ stw r4, SS_DBAT+0x30(r3)
+ stw r5, SS_DBAT+0x34(r3)
+ stw r6, SS_DBAT+0x38(r3)
+ stw r7, SS_DBAT+0x3c(r3)
+
+ mfspr r4, SPRN_IBAT0U
+ mfspr r5, SPRN_IBAT0L
+ mfspr r6, SPRN_IBAT1U
+ mfspr r7, SPRN_IBAT1L
+
+ stw r4, SS_IBAT+0x00(r3)
+ stw r5, SS_IBAT+0x04(r3)
+ stw r6, SS_IBAT+0x08(r3)
+ stw r7, SS_IBAT+0x0c(r3)
+
+ mfspr r4, SPRN_IBAT2U
+ mfspr r5, SPRN_IBAT2L
+ mfspr r6, SPRN_IBAT3U
+ mfspr r7, SPRN_IBAT3L
+
+ stw r4, SS_IBAT+0x10(r3)
+ stw r5, SS_IBAT+0x14(r3)
+ stw r6, SS_IBAT+0x18(r3)
+ stw r7, SS_IBAT+0x1c(r3)
+
+ mfspr r4, SPRN_IBAT4U
+ mfspr r5, SPRN_IBAT4L
+ mfspr r6, SPRN_IBAT5U
+ mfspr r7, SPRN_IBAT5L
+
+ stw r4, SS_IBAT+0x20(r3)
+ stw r5, SS_IBAT+0x24(r3)
+ stw r6, SS_IBAT+0x28(r3)
+ stw r7, SS_IBAT+0x2c(r3)
+
+ mfspr r4, SPRN_IBAT6U
+ mfspr r5, SPRN_IBAT6L
+ mfspr r6, SPRN_IBAT7U
+ mfspr r7, SPRN_IBAT7L
+
+ stw r4, SS_IBAT+0x30(r3)
+ stw r5, SS_IBAT+0x34(r3)
+ stw r6, SS_IBAT+0x38(r3)
+ stw r7, SS_IBAT+0x3c(r3)
+
+ mfmsr r4
+ mflr r5
+ mfcr r6
+
+ stw r4, SS_MSR(r3)
+ stw r5, SS_LR(r3)
+ stw r6, SS_CR(r3)
+ stw r1, SS_SP(r3)
+ stw r2, SS_CURRENT(r3)
+
+1: mftbu r4
+ mftb r5
+ mftbu r6
+ cmpw r4, r6
+ bne 1b
+
+ stw r4, SS_TB+0(r3)
+ stw r5, SS_TB+4(r3)
+
+ stmw r12, SS_GPREG(r3)
+
+ li r4, 0
+ addi r6, r3, SS_SR-4
+1: mfsrin r5, r4
+ stwu r5, 4(r6)
+ addis r4, r4, 0x1000
+ cmpwi r4, 0
+ bne 1b
+
+ /* Disable machine checks and critical exceptions */
+ mfmsr r4
+ rlwinm r4, r4, 0, ~MSR_CE
+ rlwinm r4, r4, 0, ~MSR_ME
+ mtmsr r4
+ isync
+
+#define TMP_VIRT_IMMR 0xf0000000
+#define DEFAULT_IMMR_VALUE 0xff400000
+#define IMMRBAR_BASE 0x0000
+
+ lis r4, immrbase@ha
+ lwz r4, immrbase@l(r4)
+
+ /* Use DBAT0 to address the current IMMR space */
+
+ ori r4, r4, 0x002a
+ mtspr SPRN_DBAT0L, r4
+ lis r8, TMP_VIRT_IMMR@h
+ ori r4, r8, 0x001e /* 1 MByte accessable from Kernel Space only */
+ mtspr SPRN_DBAT0U, r4
+ isync
+
+ /* Use DBAT1 to address the original IMMR space */
+
+ lis r4, DEFAULT_IMMR_VALUE@h
+ ori r4, r4, 0x002a
+ mtspr SPRN_DBAT1L, r4
+ lis r9, (TMP_VIRT_IMMR + 0x01000000)@h
+ ori r4, r9, 0x001e /* 1 MByte accessable from Kernel Space only */
+ mtspr SPRN_DBAT1U, r4
+ isync
+
+ /* Use DBAT2 to address the beginning of RAM. This isn't done
+ * using the normal virtual mapping, because with page debugging
+ * enabled it will be read-only. */
+
+ li r4, 0x0002
+ mtspr SPRN_DBAT2L, r4
+ lis r4, KERNELBASE@h
+ ori r4, r4, 0x001e /* 1 MByte accessable from Kernel Space only */
+ mtspr SPRN_DBAT2U, r4
+ isync
+
+ /* Flush the cache with our BAT, as there will be TLB misses
+ * otherwise if page debugging is enabled, and these misses
+ * will disturb the PLRU algorithm.
+ */
+
+ bl __flush_disable_L1
+
+ /* Keep the i-cache enabled, so the hack below for low-boot
+ * flash will work.
+ */
+ mfspr r3, SPRN_HID0
+ ori r3, r3, HID0_ICE
+ mtspr SPRN_HID0, r3
+ isync
+
+ lis r6, 0xf515
+ ori r6, r6, 0x3ae5
+
+ lis r7, mpc83xx_deep_resume@h
+ ori r7, r7, mpc83xx_deep_resume@l
+ tophys(r7, r7)
+
+ lis r5, KERNELBASE@h
+ stw r6, 0(r5)
+ stw r7, 4(r5)
+
+ /* Reset BARs */
+
+ li r4, 0
+ stw r4, 0x0024(r8)
+ stw r4, 0x002c(r8)
+ stw r4, 0x0034(r8)
+ stw r4, 0x003c(r8)
+ stw r4, 0x0064(r8)
+ stw r4, 0x006c(r8)
+
+ /* Rev 1 of the 8313 has problems with wakeup events that are
+ * pending during the transition to deep sleep state (such as if
+ * the PCI host sets the state to D3 and then D0 in rapid
+ * succession). This check shrinks the race window somewhat.
+ *
+ * See erratum PCI23, though the problem is not limited
+ * to PCI.
+ */
+
+ lwz r3, 0x0b04(r8)
+ andi. r3, r3, 1
+ bne- mpc83xx_deep_resume
+
+ /* Move IMMR back to the default location, following the
+ * procedure specified in the MPC8313 manual.
+ */
+ lwz r4, IMMRBAR_BASE(r8)
+ isync
+ lis r4, DEFAULT_IMMR_VALUE@h
+ stw r4, IMMRBAR_BASE(r8)
+ lis r4, KERNELBASE@h
+ lwz r4, 0(r4)
+ isync
+ lwz r4, IMMRBAR_BASE(r9)
+ mr r8, r9
+ isync
+
+ /* Check the Reset Configuration Word to see whether flash needs
+ * to be mapped at a low address or a high address.
+ */
+
+ lwz r4, 0x0904(r8)
+ andis. r4, r4, 0x0400
+ li r4, 0
+ beq boot_low
+ lis r4, 0xff80
+boot_low:
+ stw r4, 0x0020(r8)
+ lis r7, 0x8000
+ ori r7, r7, 0x0016
+
+ mfspr r5, SPRN_HID0
+ rlwinm r5, r5, 0, ~(HID0_DOZE | HID0_NAP)
+ oris r5, r5, HID0_SLEEP@h
+ mtspr SPRN_HID0, r5
+ isync
+
+ mfmsr r5
+ oris r5, r5, MSR_POW@h
+
+ /* Enable the flash mapping at the appropriate address. This
+ * mapping will override the RAM mapping, so there's no need to
+ * disable the latter. This must be done inside the same cache
+ * line as setting MSR_POW, so that no instruction fetches from
+ * RAM happen after the flash mapping is turned on.
+ */
+
+ .align 5
+ stw r7, 0x0024(r8)
+ sync
+ isync
+ mtmsr r5
+ isync
+1: b 1b
+
+mpc83xx_deep_resume:
+ lis r4, 1f@h
+ ori r4, r4, 1f@l
+ tophys(r4, r4)
+ mtsrr0 r4
+
+ mfmsr r4
+ rlwinm r4, r4, 0, ~(MSR_IR | MSR_DR)
+ mtsrr1 r4
+
+ rfi
+
+1: tlbia
+ bl __inval_enable_L1
+
+ lis r3, mpc83xx_sleep_save_area@h
+ ori r3, r3, mpc83xx_sleep_save_area@l
+ tophys(r3, r3)
+
+ lwz r5, SS_MEMSAVE+0(r3)
+ lwz r6, SS_MEMSAVE+4(r3)
+
+ stw r5, 0(0)
+ stw r6, 4(0)
+
+ lwz r5, SS_HID+0(r3)
+ lwz r6, SS_HID+4(r3)
+ lwz r7, SS_HID+8(r3)
+
+ mtspr SPRN_HID0, r5
+ mtspr SPRN_HID1, r6
+ mtspr SPRN_HID2, r7
+
+ lwz r4, SS_IABR+0(r3)
+ lwz r5, SS_IABR+4(r3)
+ lwz r6, SS_IBCR(r3)
+ lwz r7, SS_DABR+0(r3)
+ lwz r8, SS_DABR+4(r3)
+ lwz r9, SS_DBCR(r3)
+
+ mtspr SPRN_IABR, r4
+ mtspr SPRN_IABR2, r5
+ mtspr SPRN_IBCR, r6
+ mtspr SPRN_DABR, r7
+ mtspr SPRN_DABR2, r8
+ mtspr SPRN_DBCR, r9
+
+ li r4, 0
+ addi r6, r3, SS_SR-4
+1: lwzu r5, 4(r6)
+ mtsrin r5, r4
+ addis r4, r4, 0x1000
+ cmpwi r4, 0
+ bne 1b
+
+ lwz r4, SS_DBAT+0x00(r3)
+ lwz r5, SS_DBAT+0x04(r3)
+ lwz r6, SS_DBAT+0x08(r3)
+ lwz r7, SS_DBAT+0x0c(r3)
+
+ mtspr SPRN_DBAT0U, r4
+ mtspr SPRN_DBAT0L, r5
+ mtspr SPRN_DBAT1U, r6
+ mtspr SPRN_DBAT1L, r7
+
+ lwz r4, SS_DBAT+0x10(r3)
+ lwz r5, SS_DBAT+0x14(r3)
+ lwz r6, SS_DBAT+0x18(r3)
+ lwz r7, SS_DBAT+0x1c(r3)
+
+ mtspr SPRN_DBAT2U, r4
+ mtspr SPRN_DBAT2L, r5
+ mtspr SPRN_DBAT3U, r6
+ mtspr SPRN_DBAT3L, r7
+
+ lwz r4, SS_DBAT+0x20(r3)
+ lwz r5, SS_DBAT+0x24(r3)
+ lwz r6, SS_DBAT+0x28(r3)
+ lwz r7, SS_DBAT+0x2c(r3)
+
+ mtspr SPRN_DBAT4U, r4
+ mtspr SPRN_DBAT4L, r5
+ mtspr SPRN_DBAT5U, r6
+ mtspr SPRN_DBAT5L, r7
+
+ lwz r4, SS_DBAT+0x30(r3)
+ lwz r5, SS_DBAT+0x34(r3)
+ lwz r6, SS_DBAT+0x38(r3)
+ lwz r7, SS_DBAT+0x3c(r3)
+
+ mtspr SPRN_DBAT6U, r4
+ mtspr SPRN_DBAT6L, r5
+ mtspr SPRN_DBAT7U, r6
+ mtspr SPRN_DBAT7L, r7
+
+ lwz r4, SS_IBAT+0x00(r3)
+ lwz r5, SS_IBAT+0x04(r3)
+ lwz r6, SS_IBAT+0x08(r3)
+ lwz r7, SS_IBAT+0x0c(r3)
+
+ mtspr SPRN_IBAT0U, r4
+ mtspr SPRN_IBAT0L, r5
+ mtspr SPRN_IBAT1U, r6
+ mtspr SPRN_IBAT1L, r7
+
+ lwz r4, SS_IBAT+0x10(r3)
+ lwz r5, SS_IBAT+0x14(r3)
+ lwz r6, SS_IBAT+0x18(r3)
+ lwz r7, SS_IBAT+0x1c(r3)
+
+ mtspr SPRN_IBAT2U, r4
+ mtspr SPRN_IBAT2L, r5
+ mtspr SPRN_IBAT3U, r6
+ mtspr SPRN_IBAT3L, r7
+
+ lwz r4, SS_IBAT+0x20(r3)
+ lwz r5, SS_IBAT+0x24(r3)
+ lwz r6, SS_IBAT+0x28(r3)
+ lwz r7, SS_IBAT+0x2c(r3)
+
+ mtspr SPRN_IBAT4U, r4
+ mtspr SPRN_IBAT4L, r5
+ mtspr SPRN_IBAT5U, r6
+ mtspr SPRN_IBAT5L, r7
+
+ lwz r4, SS_IBAT+0x30(r3)
+ lwz r5, SS_IBAT+0x34(r3)
+ lwz r6, SS_IBAT+0x38(r3)
+ lwz r7, SS_IBAT+0x3c(r3)
+
+ mtspr SPRN_IBAT6U, r4
+ mtspr SPRN_IBAT6L, r5
+ mtspr SPRN_IBAT7U, r6
+ mtspr SPRN_IBAT7L, r7
+
+ lwz r4, SS_SPRG+0(r3)
+ lwz r5, SS_SPRG+4(r3)
+ lwz r6, SS_SPRG+8(r3)
+ lwz r7, SS_SPRG+12(r3)
+ lwz r8, SS_SDR1(r3)
+
+ mtspr SPRN_SPRG0, r4
+ mtspr SPRN_SPRG1, r5
+ mtspr SPRN_SPRG2, r6
+ mtspr SPRN_SPRG3, r7
+ mtsdr1 r8
+
+ lwz r4, SS_MSR(r3)
+ lwz r5, SS_LR(r3)
+ lwz r6, SS_CR(r3)
+ lwz r1, SS_SP(r3)
+ lwz r2, SS_CURRENT(r3)
+
+ mtsrr1 r4
+ mtsrr0 r5
+ mtcr r6
+
+ li r4, 0
+ mtspr SPRN_TBWL, r4
+
+ lwz r4, SS_TB+0(r3)
+ lwz r5, SS_TB+4(r3)
+
+ mtspr SPRN_TBWU, r4
+ mtspr SPRN_TBWL, r5
+
+ lmw r12, SS_GPREG(r3)
+
+ /* Kick decrementer */
+ li r0, 1
+ mtdec r0
+
+ rfi
diff --git a/arch/powerpc/platforms/83xx/suspend.c b/arch/powerpc/platforms/83xx/suspend.c
new file mode 100644
index 0000000..61bca38
--- /dev/null
+++ b/arch/powerpc/platforms/83xx/suspend.c
@@ -0,0 +1,423 @@
+/*
+ * MPC83xx suspend support
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2006-2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/pm.h>
+#include <linux/types.h>
+#include <linux/ioport.h>
+#include <linux/interrupt.h>
+#include <linux/wait.h>
+#include <linux/kthread.h>
+#include <linux/freezer.h>
+#include <linux/suspend.h>
+#include <linux/fsl_devices.h>
+#include <linux/of_platform.h>
+
+#include <asm/reg.h>
+#include <asm/io.h>
+#include <asm/time.h>
+#include <asm/mpc6xx.h>
+
+#include <sysdev/fsl_soc.h>
+
+#define PMCCR1_NEXT_STATE 0x0C /* Next state for power management */
+#define PMCCR1_NEXT_STATE_SHIFT 2
+#define PMCCR1_CURR_STATE 0x03 /* Current state for power management*/
+#define IMMR_RCW_OFFSET 0x900
+#define RCW_PCI_HOST 0x80000000
+
+void mpc83xx_enter_deep_sleep(phys_addr_t immrbase);
+
+struct mpc83xx_pmc {
+ u32 config;
+#define PMCCR_DLPEN 2 /* DDR SDRAM low power enable */
+#define PMCCR_SLPEN 1 /* System low power enable */
+
+ u32 event;
+ u32 mask;
+/* All but PMCI are deep-sleep only */
+#define PMCER_GPIO 0x100
+#define PMCER_PCI 0x080
+#define PMCER_USB 0x040
+#define PMCER_ETSEC1 0x020
+#define PMCER_ETSEC2 0x010
+#define PMCER_TIMER 0x008
+#define PMCER_INT1 0x004
+#define PMCER_INT2 0x002
+#define PMCER_PMCI 0x001
+#define PMCER_ALL 0x1FF
+
+ /* deep-sleep only */
+ u32 config1;
+#define PMCCR1_USE_STATE 0x80000000
+#define PMCCR1_PME_EN 0x00000080
+#define PMCCR1_ASSERT_PME 0x00000040
+#define PMCCR1_POWER_OFF 0x00000020
+
+ /* deep-sleep only */
+ u32 config2;
+};
+
+struct mpc83xx_rcw {
+ u32 rcwlr;
+ u32 rcwhr;
+};
+
+struct mpc83xx_clock {
+ u32 spmr;
+ u32 occr;
+ u32 sccr;
+};
+
+struct pmc_type {
+ int has_deep_sleep;
+};
+
+static struct of_device *pmc_dev;
+static int has_deep_sleep, deep_sleeping;
+static int pmc_irq;
+static struct mpc83xx_pmc __iomem *pmc_regs;
+static struct mpc83xx_clock __iomem *clock_regs;
+static int is_pci_agent, wake_from_pci;
+static phys_addr_t immrbase;
+static int pci_pm_state;
+static DECLARE_WAIT_QUEUE_HEAD(agent_wq);
+
+static u32 saved_sccr;
+static DEFINE_SPINLOCK(device_sleep_lock);
+
+void fsl_sleep_device(struct fsl_sleep_platform_data *data)
+{
+ if (clock_regs && data->sccr_mask) {
+ unsigned long flags;
+ u32 sccr;
+
+ spin_lock_irqsave(&device_sleep_lock, flags);
+ sccr = in_be32(&clock_regs->sccr);
+
+ saved_sccr &= ~data->sccr_mask;
+ saved_sccr |= sccr & data->sccr_mask;
+
+ out_be32(&clock_regs->sccr, sccr & ~data->sccr_mask);
+ spin_unlock_irqrestore(&device_sleep_lock, flags);
+ }
+}
+EXPORT_SYMBOL(fsl_sleep_device);
+
+void fsl_wake_device(struct fsl_sleep_platform_data *data)
+{
+ if (clock_regs && data->sccr_mask) {
+ unsigned long flags;
+ u32 sccr;
+
+ spin_lock_irqsave(&device_sleep_lock, flags);
+
+ sccr = in_be32(&clock_regs->sccr);
+ sccr |= saved_sccr & data->sccr_mask;
+ out_be32(&clock_regs->sccr, sccr);
+
+ spin_unlock_irqrestore(&device_sleep_lock, flags);
+ }
+}
+EXPORT_SYMBOL(fsl_wake_device);
+
+int fsl_deep_sleep(void)
+{
+ return deep_sleeping;
+}
+
+static int mpc83xx_change_state(void)
+{
+ u32 curr_state;
+ u32 reg_cfg1 = in_be32(&pmc_regs->config1);
+
+ if (is_pci_agent) {
+ pci_pm_state = (reg_cfg1 & PMCCR1_NEXT_STATE) >>
+ PMCCR1_NEXT_STATE_SHIFT;
+ curr_state = reg_cfg1 & PMCCR1_CURR_STATE;
+
+ if (curr_state != pci_pm_state) {
+ reg_cfg1 &= ~PMCCR1_CURR_STATE;
+ reg_cfg1 |= pci_pm_state;
+ out_be32(&pmc_regs->config1, reg_cfg1);
+
+ wake_up(&agent_wq);
+ return 1;
+ }
+ }
+
+ return 0;
+}
+
+static irqreturn_t pmc_irq_handler(int irq, void *dev_id)
+{
+ u32 event = in_be32(&pmc_regs->event);
+ int ret = IRQ_NONE;
+
+ if (mpc83xx_change_state())
+ ret = IRQ_HANDLED;
+
+ if (event) {
+ out_be32(&pmc_regs->event, event);
+ ret = IRQ_HANDLED;
+ }
+
+ return ret;
+}
+
+static int mpc83xx_suspend_enter(suspend_state_t state)
+{
+ int ret = -EAGAIN;
+
+ /* Don't go to sleep if there's a race where pci_pm_state changes
+ * between the agent thread checking it and the PM code disabling
+ * interrupts.
+ */
+ if (wake_from_pci) {
+ if (pci_pm_state != (deep_sleeping ? 3 : 2))
+ goto out;
+
+ out_be32(&pmc_regs->config1,
+ in_be32(&pmc_regs->config1) | PMCCR1_PME_EN);
+ }
+
+ /* Put the system into low-power mode and the RAM
+ * into self-refresh mode once the core goes to
+ * sleep.
+ */
+
+ out_be32(&pmc_regs->config, PMCCR_SLPEN | PMCCR_DLPEN);
+
+ /* If it has deep sleep (i.e. it's an 831x or compatible),
+ * disable power to the core upon entering sleep mode. This will
+ * require going through the boot firmware upon a wakeup event.
+ */
+
+ if (deep_sleeping) {
+ out_be32(&pmc_regs->mask, PMCER_ALL);
+
+ out_be32(&pmc_regs->config1,
+ in_be32(&pmc_regs->config1) | PMCCR1_POWER_OFF);
+
+ enable_kernel_fp();
+
+ mpc83xx_enter_deep_sleep(immrbase);
+
+ out_be32(&pmc_regs->config1,
+ in_be32(&pmc_regs->config1) & ~PMCCR1_POWER_OFF);
+
+ out_be32(&pmc_regs->mask, PMCER_PMCI);
+ } else {
+ out_be32(&pmc_regs->mask, PMCER_PMCI);
+
+ mpc6xx_enter_standby();
+ }
+
+ ret = 0;
+
+out:
+ out_be32(&pmc_regs->config1,
+ in_be32(&pmc_regs->config1) & ~PMCCR1_PME_EN);
+
+ return ret;
+}
+
+static void mpc83xx_suspend_finish(void)
+{
+ deep_sleeping = 0;
+}
+
+static int mpc83xx_suspend_valid(suspend_state_t state)
+{
+ return state == PM_SUSPEND_STANDBY || state == PM_SUSPEND_MEM;
+}
+
+static int mpc83xx_suspend_set_target(suspend_state_t state)
+{
+ switch (state) {
+ case PM_SUSPEND_STANDBY:
+ deep_sleeping = 0;
+ return 0;
+
+ case PM_SUSPEND_MEM:
+ if (has_deep_sleep)
+ deep_sleeping = 1;
+
+ return 0;
+
+ default:
+ return -EINVAL;
+ }
+}
+
+static int agent_thread_fn(void *data)
+{
+ while (1) {
+ wait_event_interruptible(agent_wq, pci_pm_state >= 2);
+ try_to_freeze();
+
+ if (signal_pending(current) || pci_pm_state < 2)
+ continue;
+
+ /* With a preemptible kernel (or SMP), this could race with a
+ * userspace-driven suspend request. It's probably best to
+ * avoid mixing the two with such a configuration (or else fix
+ * it by adding a mutex to state_store that we can synchronize
+ * with).
+ */
+
+ wake_from_pci = 1;
+
+ pm_suspend(pci_pm_state == 3 ? PM_SUSPEND_MEM :
+ PM_SUSPEND_STANDBY);
+
+ wake_from_pci = 0;
+ }
+
+ return 0;
+}
+
+void mpc83xx_set_agent(void)
+{
+ out_be32(&pmc_regs->config1, PMCCR1_USE_STATE);
+ out_be32(&pmc_regs->mask, PMCER_PMCI);
+
+ kthread_run(agent_thread_fn, NULL, "PCI power mgt");
+}
+
+static int mpc83xx_is_pci_agent(void)
+{
+ struct mpc83xx_rcw __iomem *rcw_regs;
+ int ret;
+
+ rcw_regs = ioremap(get_immrbase() + IMMR_RCW_OFFSET,
+ sizeof(struct mpc83xx_rcw));
+
+ if (!rcw_regs)
+ return -ENOMEM;
+
+ ret = !(in_be32(&rcw_regs->rcwhr) & RCW_PCI_HOST);
+
+ iounmap(rcw_regs);
+ return ret;
+}
+
+static struct platform_suspend_ops mpc83xx_suspend_ops = {
+ .valid = mpc83xx_suspend_valid,
+ .set_target = mpc83xx_suspend_set_target,
+ .enter = mpc83xx_suspend_enter,
+ .finish = mpc83xx_suspend_finish,
+};
+
+static int pmc_probe(struct of_device *ofdev,
+ const struct of_device_id *match)
+{
+ struct device_node *np = ofdev->node;
+ struct resource res;
+ struct pmc_type *type = match->data;
+ int ret = 0;
+
+ has_deep_sleep = type->has_deep_sleep;
+ immrbase = get_immrbase();
+ pmc_dev = ofdev;
+
+ is_pci_agent = mpc83xx_is_pci_agent();
+ if (is_pci_agent < 0)
+ return is_pci_agent;
+
+ ret = of_address_to_resource(np, 0, &res);
+ if (ret)
+ return -ENODEV;
+
+ pmc_irq = irq_of_parse_and_map(np, 0);
+ if (pmc_irq != NO_IRQ) {
+ ret = request_irq(pmc_irq, pmc_irq_handler, IRQF_SHARED,
+ "pmc", ofdev);
+
+ if (ret)
+ return -EBUSY;
+ }
+
+ pmc_regs = ioremap(res.start, sizeof(struct mpc83xx_pmc));
+
+ if (!pmc_regs) {
+ ret = -ENOMEM;
+ goto out;
+ }
+
+ ret = of_address_to_resource(np, 1, &res);
+ if (ret) {
+ ret = -ENODEV;
+ goto out_pmc;
+ }
+
+ clock_regs = ioremap(res.start, sizeof(struct mpc83xx_pmc));
+
+ if (!clock_regs) {
+ ret = -ENOMEM;
+ goto out_pmc;
+ }
+
+ if (is_pci_agent)
+ mpc83xx_set_agent();
+
+ suspend_set_ops(&mpc83xx_suspend_ops);
+ return 0;
+
+out_pmc:
+ iounmap(pmc_regs);
+out:
+ if (pmc_irq != NO_IRQ)
+ free_irq(pmc_irq, ofdev);
+
+ return ret;
+}
+
+static int pmc_remove(struct of_device *ofdev)
+{
+ return -EPERM;
+};
+
+static struct pmc_type pmc_types[] = {
+ {
+ .has_deep_sleep = 1,
+ },
+ {
+ .has_deep_sleep = 0,
+ }
+};
+
+static struct of_device_id pmc_match[] = {
+ {
+ .compatible = "fsl,mpc8313-pmc",
+ .data = &pmc_types[0],
+ },
+ {
+ .compatible = "fsl,mpc8349-pmc",
+ .data = &pmc_types[1],
+ },
+ {}
+};
+
+static struct of_platform_driver pmc_driver = {
+ .name = "mpc83xx-pmc",
+ .match_table = pmc_match,
+ .probe = pmc_probe,
+ .remove = pmc_remove
+};
+
+static int pmc_init(void)
+{
+ return of_register_platform_driver(&pmc_driver);
+}
+
+module_init(pmc_init);
diff --git a/arch/powerpc/sysdev/fsl_soc.c b/arch/powerpc/sysdev/fsl_soc.c
index e1ba33c..d5fd916 100644
--- a/arch/powerpc/sysdev/fsl_soc.c
+++ b/arch/powerpc/sysdev/fsl_soc.c
@@ -151,6 +151,33 @@ u32 get_baudrate(void)
EXPORT_SYMBOL(get_baudrate);
#endif /* CONFIG_CPM2 */
+int fsl_sleep_init(struct fsl_sleep_platform_data *sleep,
+ struct device_node *node)
+{
+ int proplen, ret = -ENODEV;
+ const u32 *sleepdata = of_get_property(node, "sleep", &proplen);
+ struct device_node *sleep_controller;
+
+ if (!sleepdata || proplen != 8)
+ return -ENODEV;
+
+ sleep_controller = of_find_node_by_phandle(sleepdata[0]);
+ if (!sleep_controller)
+ return -ENODEV;
+
+ /* There can only be one fsl,mpc83xx-pmc device in the system;
+ * it is assumed that it is the one that the pmc driver matches.
+ */
+ if (of_device_is_compatible(sleep_controller, "fsl,mpc83xx-pmc")) {
+ sleep->sccr_mask = sleepdata[1];
+ ret = 0;
+ }
+
+ of_node_put(sleep_controller);
+ return ret;
+}
+EXPORT_SYMBOL(fsl_sleep_init);
+
static int __init gfar_mdio_of_init(void)
{
struct device_node *np;
@@ -321,6 +348,8 @@ static int __init gfar_of_init(void)
of_node_put(phy);
of_node_put(mdio);
+ fsl_sleep_init(&gfar_data.sleep, np);
+
ret =
platform_device_add_data(gfar_dev, &gfar_data,
sizeof(struct
@@ -576,6 +605,8 @@ static int __init fsl_usb_of_init(void)
prop = of_get_property(np, "phy_type", NULL);
usb_data.phy_mode = determine_usb_phy(prop);
+ fsl_sleep_init(&usb_data.sleep, np);
+
ret =
platform_device_add_data(usb_dev_mph, &usb_data,
sizeof(struct
@@ -640,6 +671,8 @@ static int __init fsl_usb_of_init(void)
prop = of_get_property(np, "phy_type", NULL);
usb_data.phy_mode = determine_usb_phy(prop);
+ fsl_sleep_init(&usb_data.sleep, np);
+
if (usb_dev_dr_host) {
usb_dev_dr_host->dev.coherent_dma_mask = 0xffffffffUL;
usb_dev_dr_host->dev.dma_mask = &usb_dev_dr_host->
diff --git a/arch/powerpc/sysdev/fsl_soc.h b/arch/powerpc/sysdev/fsl_soc.h
index 74c4a96..fb52d39 100644
--- a/arch/powerpc/sysdev/fsl_soc.h
+++ b/arch/powerpc/sysdev/fsl_soc.h
@@ -10,12 +10,22 @@ extern u32 get_baudrate(void);
extern u32 fsl_get_sys_freq(void);
struct spi_board_info;
+struct fsl_sleep_platform_data;
+struct device_node;
extern int fsl_spi_init(struct spi_board_info *board_infos,
unsigned int num_board_infos,
void (*activate_cs)(u8 cs, u8 polarity),
void (*deactivate_cs)(u8 cs, u8 polarity));
+int fsl_sleep_init(struct fsl_sleep_platform_data *sleep,
+ struct device_node *node);
+
+/* Calls to fsl_sleep_dev and fsl_wake_dev cannot be nested. */
+void fsl_sleep_dev(struct fsl_sleep_platform_data *sleep);
+void fsl_wake_dev(struct fsl_sleep_platform_data *sleep);
+
extern void fsl_rstcr_restart(char *cmd);
+
#endif
#endif
diff --git a/arch/powerpc/sysdev/ipic.c b/arch/powerpc/sysdev/ipic.c
index 05a56e5..e2388cf 100644
--- a/arch/powerpc/sysdev/ipic.c
+++ b/arch/powerpc/sysdev/ipic.c
@@ -22,6 +22,7 @@
#include <linux/device.h>
#include <linux/bootmem.h>
#include <linux/spinlock.h>
+#include <linux/fsl_devices.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/prom.h>
@@ -724,8 +725,78 @@ unsigned int ipic_get_irq(void)
return irq_linear_revmap(primary_ipic->irqhost, irq);
}
+#ifdef CONFIG_PM
+static struct {
+ u32 sicfr;
+ u32 siprr[2];
+ u32 simsr[2];
+ u32 sicnr;
+ u32 smprr[2];
+ u32 semsr;
+ u32 secnr;
+ u32 sermr;
+ u32 sercr;
+} ipic_saved_state;
+
+static int ipic_suspend(struct sys_device *sdev, pm_message_t state)
+{
+ struct ipic *ipic = primary_ipic;
+
+ ipic_saved_state.sicfr = ipic_read(ipic->regs, IPIC_SICFR);
+ ipic_saved_state.siprr[0] = ipic_read(ipic->regs, IPIC_SIPRR_A);
+ ipic_saved_state.siprr[1] = ipic_read(ipic->regs, IPIC_SIPRR_D);
+ ipic_saved_state.simsr[0] = ipic_read(ipic->regs, IPIC_SIMSR_H);
+ ipic_saved_state.simsr[1] = ipic_read(ipic->regs, IPIC_SIMSR_L);
+ ipic_saved_state.sicnr = ipic_read(ipic->regs, IPIC_SICNR);
+ ipic_saved_state.smprr[0] = ipic_read(ipic->regs, IPIC_SMPRR_A);
+ ipic_saved_state.smprr[1] = ipic_read(ipic->regs, IPIC_SMPRR_B);
+ ipic_saved_state.semsr = ipic_read(ipic->regs, IPIC_SEMSR);
+ ipic_saved_state.secnr = ipic_read(ipic->regs, IPIC_SECNR);
+ ipic_saved_state.sermr = ipic_read(ipic->regs, IPIC_SERMR);
+ ipic_saved_state.sercr = ipic_read(ipic->regs, IPIC_SERCR);
+
+ if (fsl_deep_sleep()) {
+ /* In deep sleep, make sure there can be no
+ * pending interrupts, as this can cause
+ * problems on 831x.
+ */
+ ipic_write(ipic->regs, IPIC_SIMSR_H, 0);
+ ipic_write(ipic->regs, IPIC_SIMSR_L, 0);
+ ipic_write(ipic->regs, IPIC_SEMSR, 0);
+ ipic_write(ipic->regs, IPIC_SERMR, 0);
+ }
+
+ return 0;
+}
+
+static int ipic_resume(struct sys_device *sdev)
+{
+ struct ipic *ipic = primary_ipic;
+
+ ipic_write(ipic->regs, IPIC_SICFR, ipic_saved_state.sicfr);
+ ipic_write(ipic->regs, IPIC_SIPRR_A, ipic_saved_state.siprr[0]);
+ ipic_write(ipic->regs, IPIC_SIPRR_D, ipic_saved_state.siprr[1]);
+ ipic_write(ipic->regs, IPIC_SIMSR_H, ipic_saved_state.simsr[0]);
+ ipic_write(ipic->regs, IPIC_SIMSR_L, ipic_saved_state.simsr[1]);
+ ipic_write(ipic->regs, IPIC_SICNR, ipic_saved_state.sicnr);
+ ipic_write(ipic->regs, IPIC_SMPRR_A, ipic_saved_state.smprr[0]);
+ ipic_write(ipic->regs, IPIC_SMPRR_B, ipic_saved_state.smprr[1]);
+ ipic_write(ipic->regs, IPIC_SEMSR, ipic_saved_state.semsr);
+ ipic_write(ipic->regs, IPIC_SECNR, ipic_saved_state.secnr);
+ ipic_write(ipic->regs, IPIC_SERMR, ipic_saved_state.sermr);
+ ipic_write(ipic->regs, IPIC_SERCR, ipic_saved_state.sercr);
+
+ return 0;
+}
+#else
+#define ipic_suspend NULL
+#define ipic_resume NULL
+#endif
+
static struct sysdev_class ipic_sysclass = {
set_kset_name("ipic"),
+ .suspend = ipic_suspend,
+ .resume = ipic_resume,
};
static struct sys_device device_ipic = {
diff --git a/include/asm-powerpc/reg.h b/include/asm-powerpc/reg.h
index 1f68504..68968c1 100644
--- a/include/asm-powerpc/reg.h
+++ b/include/asm-powerpc/reg.h
@@ -149,7 +149,9 @@
#define CTRL_RUNLATCH 0x1
#define SPRN_DABR 0x3F5 /* Data Address Breakpoint Register */
#define DABR_TRANSLATION (1UL << 2)
+#define SPRN_DABR2 0x13D /* 83xx */
#define SPRN_DAR 0x013 /* Data Address Register */
+#define SPRN_DBCR 0x136 /* 83xx Data Breakpoint Control Reg */
#define SPRN_DSISR 0x012 /* Data Storage Interrupt Status Register */
#define DSISR_NOHPTE 0x40000000 /* no translation found */
#define DSISR_PROTFAULT 0x08000000 /* protection fault */
@@ -255,6 +257,8 @@
#define HID1_PS (1<<16) /* 750FX PLL selection */
#define SPRN_HID2 0x3F8 /* Hardware Implementation Register 2 */
#define SPRN_IABR 0x3F2 /* Instruction Address Breakpoint Register */
+#define SPRN_IABR2 0x3FA /* 83xx */
+#define SPRN_IBCR 0x135 /* 83xx Insn Breakpoint Control Reg */
#define SPRN_HID4 0x3F4 /* 970 HID4 */
#define SPRN_HID5 0x3F6 /* 970 HID5 */
#define SPRN_HID6 0x3F9 /* BE HID 6 */
diff --git a/include/linux/fsl_devices.h b/include/linux/fsl_devices.h
index 1831b19..5cec939 100644
--- a/include/linux/fsl_devices.h
+++ b/include/linux/fsl_devices.h
@@ -45,10 +45,27 @@
*
*/
+struct fsl_sleep_platform_data {
+ /*
+ * The bits set in this mask will be cleared in the SCCR
+ * when put to sleep, and restored on wakeup.
+ */
+ u32 sccr_mask;
+};
+
+/*
+ * Calls to fsl_sleep_device do not nest -- if you call
+ * sleep twice without an intervening wake, you will not
+ * be able to wake the device again.
+ */
+void fsl_sleep_device(struct fsl_sleep_platform_data *data);
+void fsl_wake_device(struct fsl_sleep_platform_data *data);
+
struct gianfar_platform_data {
/* device specific information */
u32 device_flags;
/* board specific information */
+ struct fsl_sleep_platform_data sleep;
u32 board_flags;
u32 bus_id;
u32 phy_id;
@@ -104,6 +121,7 @@ struct fsl_usb2_platform_data {
enum fsl_usb2_operating_modes operating_mode;
enum fsl_usb2_phy_modes phy_mode;
unsigned int port_enables;
+ struct fsl_sleep_platform_data sleep;
};
/* Flags in fsl_usb2_mph_platform_data */
@@ -126,5 +144,11 @@ struct mpc8xx_pcmcia_ops {
int(*voltage_set)(int slot, int vcc, int vpp);
};
+/* Returns non-zero if the current suspend operation would
+ * lead to a deep sleep (i.e. power removed from the core,
+ * instead of just the clock).
+ */
+int fsl_deep_sleep(void);
+
#endif /* _FSL_DEVICE_H_ */
#endif /* __KERNEL__ */
--
1.5.3.7
^ permalink raw reply related
* Re: [PATCH 2/3] mpc82xx: Embedded Planet EP8248E support
From: Scott Wood @ 2007-12-12 22:48 UTC (permalink / raw)
To: Stephen Rothwell; +Cc: linuxppc-dev
In-Reply-To: <20071212154306.dee76c80.sfr@canb.auug.org.au>
Stephen Rothwell wrote:
>> + ep8248e_bcsr = of_iomap(ep8248e_bcsr_node, 0);
>
> of_node_put(ep8248e_bcsr_node;
No, because we hold on to the node for later use in ep8248e_mdio_probe().
BTW, is there any actual node removal done that justifies dealing with
refcounts everywhere?
-Scot
^ permalink raw reply
* Re: [PATCH v2] [POWERPC] pasemi: Implement MSI support
From: Michael Ellerman @ 2007-12-12 22:51 UTC (permalink / raw)
To: Olof Johansson; +Cc: linuxppc-dev
In-Reply-To: <20071212072310.GA3173@lixom.net>
[-- Attachment #1: Type: text/plain, Size: 1444 bytes --]
On Wed, 2007-12-12 at 01:23 -0600, Olof Johansson wrote:
> On Wed, Dec 12, 2007 at 05:49:39PM +1100, Michael Ellerman wrote:
> > Before the ugliness spreads .. I'm pretty sure we can get this from the
> > chip_data of the virq - I haven't fixed it though because I wasn't sure
> > if using chip_data was kosher or not.
>
> Hmm, maybe.
>
> I can forsee MSI and legacy interrupts being handled by different irq
> hosts on systems where they are cascaded, so I'm not 100% sure that's a
> workable way to do it (I assume you'd look it up through the pci_dev's
> legacy irq field, right?).
No you're right that won't work, what I had in mind would work for
teardown, we could get the mpic from the chip_data of each virq.
But for setup we need to know which mpic to create the mapping on
_before_ it's mapped (obviously) so using chip_data doesn't work. And
yeah, guessing based on the legacy irq of the pci_dev would not be safe.
The only safe way to do it I think would be to walk up the interrupt
tree and find the interrupt controller node, then do an irq_find_host(),
but that's a lot of fuss to save one static variable :)
Patch looks good otherwise.
cheers
--
Michael Ellerman
OzLabs, IBM Australia Development Lab
wwweb: http://michael.ellerman.id.au
phone: +61 2 6212 1183 (tie line 70 21183)
We do not inherit the earth from our ancestors,
we borrow it from our children. - S.M.A.R.T Person
[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply
* [PATCH v2 3/3] Eliminate section mismatch warning in cpm2_reset().
From: Scott Wood @ 2007-12-12 22:54 UTC (permalink / raw)
To: galak; +Cc: linuxppc-dev
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
arch/powerpc/sysdev/cpm2_common.c | 3 +--
1 files changed, 1 insertions(+), 2 deletions(-)
diff --git a/arch/powerpc/sysdev/cpm2_common.c b/arch/powerpc/sysdev/cpm2_common.c
index 859362f..c1d8240 100644
--- a/arch/powerpc/sysdev/cpm2_common.c
+++ b/arch/powerpc/sysdev/cpm2_common.c
@@ -61,8 +61,7 @@ cpm2_map_t __iomem *cpm2_immr;
of space for CPM as it is larger
than on PQ2 */
-void
-cpm2_reset(void)
+void __init cpm2_reset(void)
{
#ifdef CONFIG_PPC_85xx
cpm2_immr = ioremap(CPM_MAP_ADDR, CPM_MAP_SIZE);
--
1.5.3.7
^ permalink raw reply related
* [PATCH v2 2/3] mpc82xx: Embedded Planet EP8248E support
From: Scott Wood @ 2007-12-12 22:54 UTC (permalink / raw)
To: galak; +Cc: linuxppc-dev
This board is also resold by Freescale under the names
"QUICCStart MPC8248 Evaluation System" and "CWH-PPC-8248N-VE".
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
arch/powerpc/boot/Makefile | 3 +-
arch/powerpc/boot/dts/ep8248e.dts | 193 +++++++
arch/powerpc/boot/ep8248e.c | 55 ++
arch/powerpc/boot/wrapper | 2 +-
arch/powerpc/configs/ep8248e_defconfig | 864 ++++++++++++++++++++++++++++++++
arch/powerpc/platforms/82xx/Kconfig | 13 +
arch/powerpc/platforms/82xx/Makefile | 1 +
arch/powerpc/platforms/82xx/ep8248e.c | 325 ++++++++++++
include/asm-powerpc/mpc8260.h | 1 +
9 files changed, 1455 insertions(+), 2 deletions(-)
create mode 100644 arch/powerpc/boot/dts/ep8248e.dts
create mode 100644 arch/powerpc/boot/ep8248e.c
create mode 100644 arch/powerpc/configs/ep8248e_defconfig
create mode 100644 arch/powerpc/platforms/82xx/ep8248e.c
diff --git a/arch/powerpc/boot/Makefile b/arch/powerpc/boot/Makefile
index 27b637c..29e359d 100644
--- a/arch/powerpc/boot/Makefile
+++ b/arch/powerpc/boot/Makefile
@@ -58,7 +58,7 @@ src-plat := of.c cuboot-52xx.c cuboot-83xx.c cuboot-85xx.c holly.c \
cuboot-ebony.c treeboot-ebony.c prpmc2800.c \
ps3-head.S ps3-hvcall.S ps3.c treeboot-bamboo.c cuboot-8xx.c \
cuboot-pq2.c cuboot-sequoia.c treeboot-walnut.c cuboot-bamboo.c \
- fixed-head.S ep88xc.c cuboot-hpc2.c redboot-8xx.c
+ fixed-head.S ep88xc.c cuboot-hpc2.c redboot-8xx.c ep8248e.c
src-boot := $(src-wlib) $(src-plat) empty.c
src-boot := $(addprefix $(obj)/, $(src-boot))
@@ -155,6 +155,7 @@ ifneq ($(CONFIG_DEVICE_TREE),"")
image-$(CONFIG_PPC_8xx) += cuImage.8xx
image-$(CONFIG_PPC_EP88XC) += zImage.ep88xc
image-$(CONFIG_8260) += cuImage.pq2
+image-$(CONFIG_EP8248E) += zImage.ep8248e
image-$(CONFIG_PPC_MPC52xx) += cuImage.52xx
image-$(CONFIG_PPC_83xx) += cuImage.83xx
image-$(CONFIG_PPC_85xx) += cuImage.85xx
diff --git a/arch/powerpc/boot/dts/ep8248e.dts b/arch/powerpc/boot/dts/ep8248e.dts
new file mode 100644
index 0000000..11d21ed
--- /dev/null
+++ b/arch/powerpc/boot/dts/ep8248e.dts
@@ -0,0 +1,193 @@
+/*
+ * Device Tree for the Embedded Planet EP8248E board running PlanetCore.
+ *
+ * Copyright 2007 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/ {
+ model = "EP8248E";
+ compatible = "fsl,ep8248e";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,8248@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <d#32>;
+ i-cache-line-size = <d#32>;
+ d-cache-size = <d#16384>;
+ i-cache-size = <d#16384>;
+ timebase-frequency = <0>;
+ clock-frequency = <0>;
+ };
+ };
+
+ localbus {
+ compatible = "fsl,ep8248e-localbus",
+ "fsl,mpc8248-localbus",
+ "fsl,pq2-localbus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <f0010100 40>;
+
+ ranges = <0 0 fc000000 04000000
+ 1 0 fa000000 00008000>;
+
+ flash@0,3800000 {
+ compatible = "cfi-flash";
+ reg = <0 3800000 800000>;
+ bank-width = <4>;
+ device-width = <2>;
+ };
+
+ bcsr@1,0 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <1 0 10>;
+ compatible = "fsl,ep8248e-bcsr";
+ ranges;
+
+ mdio {
+ device_type = "mdio";
+ compatible = "fsl,ep8248e-mdio-bitbang";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1 8 1>;
+
+ PHY0: ethernet-phy@0 {
+ interrupt-parent = <&PIC>;
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+
+ PHY1: ethernet-phy@1 {
+ interrupt-parent = <&PIC>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0>;
+ };
+
+ soc@f0000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "fsl,mpc8248", "fsl,pq2-soc";
+ ranges = <00000000 f0000000 00053000>;
+
+ // Temporary -- will go away once kernel uses ranges for get_immrbase().
+ reg = <f0000000 00053000>;
+
+ cpm@119c0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #interrupt-cells = <2>;
+ compatible = "fsl,mpc8248-cpm", "fsl,cpm2";
+ reg = <119c0 30>;
+ ranges;
+
+ muram {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 10000>;
+
+ data@0 {
+ compatible = "fsl,cpm-muram-data";
+ reg = <0 1100 1140 ec0 9800 800>;
+ };
+ };
+
+ brg@119f0 {
+ compatible = "fsl,mpc8272-brg",
+ "fsl,cpm2-brg",
+ "fsl,cpm-brg";
+ reg = <119f0 10 115f0 10>;
+ };
+
+ /* Monitor port/SMC1 */
+ serial@11a80 {
+ device_type = "serial";
+ compatible = "fsl,mpc8248-smc-uart",
+ "fsl,cpm2-smc-uart";
+ reg = <11a80 20 1100 40>;
+ interrupts = <4 8>;
+ interrupt-parent = <&PIC>;
+ fsl,cpm-brg = <7>;
+ fsl,cpm-command = <1d000000>;
+ linux,planetcore-label = "SMC1";
+ };
+
+ /* "Serial" port/SCC1 */
+ serial@11a00 {
+ device_type = "serial";
+ compatible = "fsl,mpc8248-scc-uart",
+ "fsl,cpm2-scc-uart";
+ reg = <11a00 20 8000 100>;
+ interrupts = <28 8>;
+ interrupt-parent = <&PIC>;
+ fsl,cpm-brg = <1>;
+ fsl,cpm-command = <00800000>;
+ linux,planetcore-label = "SCC1";
+ };
+
+ ethernet@11300 {
+ device_type = "network";
+ compatible = "fsl,mpc8248-fcc-enet",
+ "fsl,cpm2-fcc-enet";
+ reg = <11300 20 8400 100 11390 1>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <20 8>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY0>;
+ linux,network-index = <0>;
+ fsl,cpm-command = <12000300>;
+ };
+
+ ethernet@11320 {
+ device_type = "network";
+ compatible = "fsl,mpc8248-fcc-enet",
+ "fsl,cpm2-fcc-enet";
+ reg = <11320 20 8500 100 113b0 1>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <21 8>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY1>;
+ linux,network-index = <1>;
+ fsl,cpm-command = <16200300>;
+ };
+
+ usb@11b60 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc8248-usb",
+ "fsl,cpm2-usb";
+ reg = <11b60 18 8b00 100>;
+ interrupt-parent = <&PIC>;
+ interrupts = <b 8>;
+ fsl,cpm-command = <2e600000>;
+ };
+ };
+
+ PIC: interrupt-controller@10c00 {
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ reg = <10c00 80>;
+ compatible = "fsl,mpc8248-pic", "fsl,pq2-pic";
+ };
+ };
+};
diff --git a/arch/powerpc/boot/ep8248e.c b/arch/powerpc/boot/ep8248e.c
new file mode 100644
index 0000000..f57d14d
--- /dev/null
+++ b/arch/powerpc/boot/ep8248e.c
@@ -0,0 +1,55 @@
+/*
+ * Embedded Planet EP8248E with PlanetCore firmware
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "planetcore.h"
+#include "pq2.h"
+
+static char *table;
+static u64 mem_size;
+
+#include <io.h>
+
+static void platform_fixups(void)
+{
+ u64 val;
+
+ dt_fixup_memory(0, mem_size);
+ planetcore_set_mac_addrs(table);
+
+ if (!planetcore_get_decimal(table, PLANETCORE_KEY_CRYSTAL_HZ, &val)) {
+ printf("No PlanetCore crystal frequency key.\r\n");
+ return;
+ }
+
+ pq2_fixup_clocks(val);
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+ unsigned long r6, unsigned long r7)
+{
+ table = (char *)r3;
+ planetcore_prepare_table(table);
+
+ if (!planetcore_get_decimal(table, PLANETCORE_KEY_MB_RAM, &mem_size))
+ return;
+
+ mem_size *= 1024 * 1024;
+ simple_alloc_init(_end, mem_size - (unsigned long)_end, 32, 64);
+
+ fdt_init(_dtb_start);
+
+ planetcore_set_stdout_path(table);
+ serial_console_init();
+ platform_ops.fixups = platform_fixups;
+}
diff --git a/arch/powerpc/boot/wrapper b/arch/powerpc/boot/wrapper
index 68fde3d..93ce041 100755
--- a/arch/powerpc/boot/wrapper
+++ b/arch/powerpc/boot/wrapper
@@ -168,7 +168,7 @@ ps3)
ksection=.kernel:vmlinux.bin
isection=.kernel:initrd
;;
-ep88xc|redboot*)
+ep88xc|ep8248e|redboot*)
platformo="$object/fixed-head.o $object/$platform.o"
binary=y
;;
diff --git a/arch/powerpc/configs/ep8248e_defconfig b/arch/powerpc/configs/ep8248e_defconfig
new file mode 100644
index 0000000..704ffcc
--- /dev/null
+++ b/arch/powerpc/configs/ep8248e_defconfig
@@ -0,0 +1,864 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.24-rc3
+# Mon Dec 10 13:01:33 2007
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+CONFIG_6xx=y
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_PPC_FPU=y
+CONFIG_PPC_STD_MMU=y
+CONFIG_PPC_STD_MMU_32=y
+# CONFIG_PPC_MM_SLICES is not set
+# CONFIG_SMP is not set
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+# CONFIG_PPC_UDBG_16550 is not set
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+# CONFIG_EXPERIMENTAL is not set
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+# CONFIG_BLK_DEV_INITRD is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+CONFIG_KALLSYMS_ALL=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+# CONFIG_MODULES is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_AS is not set
+CONFIG_IOSCHED_DEADLINE=y
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_DEFAULT_AS is not set
+CONFIG_DEFAULT_DEADLINE=y
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="deadline"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MULTIPLATFORM is not set
+CONFIG_PPC_82xx=y
+# CONFIG_PPC_83xx is not set
+# CONFIG_PPC_86xx is not set
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_MPC8272_ADS is not set
+# CONFIG_PQ2FADS is not set
+CONFIG_EP8248E=y
+# CONFIG_PQ2ADS is not set
+CONFIG_8260=y
+CONFIG_8272=y
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+CONFIG_CPM2=y
+CONFIG_PPC_CPM_NEW_BINDING=y
+# CONFIG_FSL_ULI1575 is not set
+CONFIG_CPM=y
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+CONFIG_BINFMT_MISC=y
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+CONFIG_PROC_DEVICETREE=y
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
+# CONFIG_SECCOMP is not set
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE="ep8248e.dts"
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_FSL_SOC=y
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0xc0000000
+CONFIG_BOOT_LOAD=0x00400000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+CONFIG_INET_TUNNEL=y
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_IP_VS is not set
+CONFIG_IPV6=y
+# CONFIG_IPV6_PRIVACY is not set
+# CONFIG_IPV6_ROUTER_PREF is not set
+# CONFIG_INET6_AH is not set
+# CONFIG_INET6_ESP is not set
+# CONFIG_INET6_IPCOMP is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+CONFIG_INET6_XFRM_MODE_TRANSPORT=y
+CONFIG_INET6_XFRM_MODE_TUNNEL=y
+CONFIG_INET6_XFRM_MODE_BEET=y
+CONFIG_IPV6_SIT=y
+# CONFIG_IPV6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+CONFIG_NETFILTER=y
+# CONFIG_NETFILTER_DEBUG is not set
+
+#
+# Core Netfilter Configuration
+#
+# CONFIG_NETFILTER_NETLINK is not set
+# CONFIG_NF_CONNTRACK_ENABLED is not set
+# CONFIG_NF_CONNTRACK is not set
+# CONFIG_NETFILTER_XTABLES is not set
+
+#
+# IP: Netfilter Configuration
+#
+# CONFIG_IP_NF_QUEUE is not set
+# CONFIG_IP_NF_IPTABLES is not set
+# CONFIG_IP_NF_ARPTABLES is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+# CONFIG_MTD_PARTITIONS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+CONFIG_MTD_CFI_NOSWAP=y
+# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set
+# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set
+CONFIG_MTD_CFI_GEOMETRY=y
+# CONFIG_MTD_MAP_BANK_WIDTH_1 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_2 is not set
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+# CONFIG_MTD_CFI_I1 is not set
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_OTP is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_RAM is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_MISC_DEVICES is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+CONFIG_DAVICOM_PHY=y
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_FIXED_PHY is not set
+CONFIG_MDIO_BITBANG=y
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_B44 is not set
+CONFIG_FS_ENET=y
+# CONFIG_FS_ENET_HAS_SCC is not set
+CONFIG_FS_ENET_HAS_FCC=y
+# CONFIG_FS_ENET_MDIO_FCC is not set
+CONFIG_NETDEV_1000=y
+CONFIG_NETDEV_10000=y
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_KEYBOARD_ATKBD=y
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_LIFEBOOK=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+# CONFIG_SERIO_I8042 is not set
+CONFIG_SERIO_SERPORT=y
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_CPM=y
+CONFIG_SERIAL_CPM_CONSOLE=y
+CONFIG_SERIAL_CPM_SCC1=y
+# CONFIG_SERIAL_CPM_SCC2 is not set
+# CONFIG_SERIAL_CPM_SCC3 is not set
+CONFIG_SERIAL_CPM_SCC4=y
+# CONFIG_SERIAL_CPM_SMC1 is not set
+# CONFIG_SERIAL_CPM_SMC2 is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_NVRAM is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_JBD=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+CONFIG_AUTOFS4_FS=y
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_JFFS2_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=y
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+CONFIG_NLS_UTF8=y
+# CONFIG_UCC_SLOW is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+# CONFIG_CRC32 is not set
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_INSTRUMENTATION=y
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+# CONFIG_DETECT_SOFTLOCKUP is not set
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_KGDB_CONSOLE is not set
+CONFIG_BDI_SWITCH=y
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_MANAGER=y
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_WP512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=y
+# CONFIG_CRYPTO_CRYPTD is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_PPC_CLOCK is not set
+CONFIG_PPC_LIB_RHEAP=y
diff --git a/arch/powerpc/platforms/82xx/Kconfig b/arch/powerpc/platforms/82xx/Kconfig
index 541fbb8..4fad6c7 100644
--- a/arch/powerpc/platforms/82xx/Kconfig
+++ b/arch/powerpc/platforms/82xx/Kconfig
@@ -26,6 +26,19 @@ config PQ2FADS
help
This option enables support for the PQ2FADS board
+config EP8248E
+ bool "Embedded Planet EP8248E (a.k.a. CWH-PPC-8248N-VE)"
+ select 8272
+ select 8260
+ select FSL_SOC
+ select PPC_CPM_NEW_BINDING
+ select MDIO_BITBANG
+ help
+ This enables support for the Embedded Planet EP8248E board.
+
+ This board is also resold by Freescale as the QUICCStart
+ MPC8248 Evaluation System and/or the CWH-PPC-8248N-VE.
+
endchoice
config PQ2ADS
diff --git a/arch/powerpc/platforms/82xx/Makefile b/arch/powerpc/platforms/82xx/Makefile
index 68c8b0c..6cd5cd5 100644
--- a/arch/powerpc/platforms/82xx/Makefile
+++ b/arch/powerpc/platforms/82xx/Makefile
@@ -5,3 +5,4 @@ obj-$(CONFIG_MPC8272_ADS) += mpc8272_ads.o
obj-$(CONFIG_CPM2) += pq2.o
obj-$(CONFIG_PQ2_ADS_PCI_PIC) += pq2ads-pci-pic.o
obj-$(CONFIG_PQ2FADS) += pq2fads.o
+obj-$(CONFIG_EP8248E) += ep8248e.o
diff --git a/arch/powerpc/platforms/82xx/ep8248e.c b/arch/powerpc/platforms/82xx/ep8248e.c
new file mode 100644
index 0000000..9753ae5
--- /dev/null
+++ b/arch/powerpc/platforms/82xx/ep8248e.c
@@ -0,0 +1,325 @@
+/*
+ * Embedded Planet EP8248E support
+ *
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/fsl_devices.h>
+#include <linux/mdio-bitbang.h>
+#include <linux/of_platform.h>
+
+#include <asm/io.h>
+#include <asm/cpm2.h>
+#include <asm/udbg.h>
+#include <asm/machdep.h>
+#include <asm/time.h>
+#include <asm/mpc8260.h>
+#include <asm/prom.h>
+
+#include <sysdev/fsl_soc.h>
+#include <sysdev/cpm2_pic.h>
+
+#include "pq2.h"
+
+static u8 __iomem *ep8248e_bcsr;
+static struct device_node *ep8248e_bcsr_node;
+
+#define BCSR7_SCC2_ENABLE 0x10
+
+#define BCSR8_PHY1_ENABLE 0x80
+#define BCSR8_PHY1_POWER 0x40
+#define BCSR8_PHY2_ENABLE 0x20
+#define BCSR8_PHY2_POWER 0x10
+#define BCSR8_MDIO_READ 0x04
+#define BCSR8_MDIO_CLOCK 0x02
+#define BCSR8_MDIO_DATA 0x01
+
+#define BCSR9_USB_ENABLE 0x80
+#define BCSR9_USB_POWER 0x40
+#define BCSR9_USB_HOST 0x20
+#define BCSR9_USB_FULL_SPEED_TARGET 0x10
+
+static void __init ep8248_pic_init(void)
+{
+ struct device_node *np = of_find_compatible_node(NULL, NULL, "fsl,pq2-pic");
+ if (!np) {
+ printk(KERN_ERR "PIC init: can not find cpm-pic node\n");
+ return;
+ }
+
+ cpm2_pic_init(np);
+ of_node_put(np);
+}
+
+static void ep8248e_set_mdc(struct mdiobb_ctrl *ctrl, int level)
+{
+ if (level)
+ setbits8(&ep8248e_bcsr[8], BCSR8_MDIO_CLOCK);
+ else
+ clrbits8(&ep8248e_bcsr[8], BCSR8_MDIO_CLOCK);
+
+ /* Read back to flush the write. */
+ in_8(&ep8248e_bcsr[8]);
+}
+
+static void ep8248e_set_mdio_dir(struct mdiobb_ctrl *ctrl, int output)
+{
+ if (output)
+ clrbits8(&ep8248e_bcsr[8], BCSR8_MDIO_READ);
+ else
+ setbits8(&ep8248e_bcsr[8], BCSR8_MDIO_READ);
+
+ /* Read back to flush the write. */
+ in_8(&ep8248e_bcsr[8]);
+}
+
+static void ep8248e_set_mdio_data(struct mdiobb_ctrl *ctrl, int data)
+{
+ if (data)
+ setbits8(&ep8248e_bcsr[8], BCSR8_MDIO_DATA);
+ else
+ clrbits8(&ep8248e_bcsr[8], BCSR8_MDIO_DATA);
+
+ /* Read back to flush the write. */
+ in_8(&ep8248e_bcsr[8]);
+}
+
+static int ep8248e_get_mdio_data(struct mdiobb_ctrl *ctrl)
+{
+ return in_8(&ep8248e_bcsr[8]) & BCSR8_MDIO_DATA;
+}
+
+static struct mdiobb_ops ep8248e_mdio_ops = {
+ .set_mdc = ep8248e_set_mdc,
+ .set_mdio_dir = ep8248e_set_mdio_dir,
+ .set_mdio_data = ep8248e_set_mdio_data,
+ .get_mdio_data = ep8248e_get_mdio_data,
+ .owner = THIS_MODULE,
+};
+
+static struct mdiobb_ctrl ep8248e_mdio_ctrl = {
+ .ops = &ep8248e_mdio_ops,
+};
+
+static int __devinit ep8248e_mdio_probe(struct of_device *ofdev,
+ const struct of_device_id *match)
+{
+ struct mii_bus *bus;
+ struct resource res;
+ struct device_node *node;
+ int ret, i;
+
+ node = of_get_parent(ofdev->node);
+ of_node_put(node);
+ if (node != ep8248e_bcsr_node)
+ return -ENODEV;
+
+ ret = of_address_to_resource(ofdev->node, 0, &res);
+ if (ret)
+ return ret;
+
+ bus = alloc_mdio_bitbang(&ep8248e_mdio_ctrl);
+ if (!bus)
+ return -ENOMEM;
+
+ bus->phy_mask = 0;
+ bus->irq = kmalloc(sizeof(int) * PHY_MAX_ADDR, GFP_KERNEL);
+
+ for (i = 0; i < PHY_MAX_ADDR; i++)
+ bus->irq[i] = -1;
+
+ bus->name = "ep8248e-mdio-bitbang";
+ bus->dev = &ofdev->dev;
+ bus->id = res.start;
+
+ return mdiobus_register(bus);
+}
+
+static int ep8248e_mdio_remove(struct of_device *ofdev)
+{
+ BUG();
+ return 0;
+}
+
+static const struct of_device_id ep8248e_mdio_match[] = {
+ {
+ .compatible = "fsl,ep8248e-mdio-bitbang",
+ },
+ {},
+};
+
+static struct of_platform_driver ep8248e_mdio_driver = {
+ .name = "ep8248e-mdio-bitbang",
+ .match_table = ep8248e_mdio_match,
+ .probe = ep8248e_mdio_probe,
+ .remove = ep8248e_mdio_remove,
+};
+
+struct cpm_pin {
+ int port, pin, flags;
+};
+
+static const struct cpm_pin ep8248_pins[] = {
+ /* SMC1 */
+ {2, 4, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 5, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+
+ /* SCC1 */
+ {2, 14, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 15, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {3, 29, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {3, 30, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {3, 31, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+
+ /* FCC1 */
+ {0, 14, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 15, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 16, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 17, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 18, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 19, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 20, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 21, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 26, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {0, 27, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {0, 28, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {0, 29, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {0, 30, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {0, 31, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {2, 21, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 22, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+
+ /* FCC2 */
+ {1, 18, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 19, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 20, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 21, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 22, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {1, 23, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {1, 24, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {1, 25, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {1, 26, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 27, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 28, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 29, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {1, 30, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 31, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {2, 18, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 19, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+
+ /* I2C */
+ {4, 14, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {4, 15, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+
+ /* USB */
+ {2, 10, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 11, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 20, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {2, 24, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {3, 23, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {3, 24, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {3, 25, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+};
+
+static void __init init_ioports(void)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(ep8248_pins); i++) {
+ const struct cpm_pin *pin = &ep8248_pins[i];
+ cpm2_set_pin(pin->port, pin->pin, pin->flags);
+ }
+
+ cpm2_smc_clk_setup(CPM_CLK_SMC1, CPM_BRG7);
+ cpm2_clk_setup(CPM_CLK_SCC1, CPM_BRG1, CPM_CLK_RX);
+ cpm2_clk_setup(CPM_CLK_SCC1, CPM_BRG1, CPM_CLK_TX);
+ cpm2_clk_setup(CPM_CLK_SCC3, CPM_CLK8, CPM_CLK_TX); /* USB */
+ cpm2_clk_setup(CPM_CLK_FCC1, CPM_CLK11, CPM_CLK_RX);
+ cpm2_clk_setup(CPM_CLK_FCC1, CPM_CLK10, CPM_CLK_TX);
+ cpm2_clk_setup(CPM_CLK_FCC2, CPM_CLK13, CPM_CLK_RX);
+ cpm2_clk_setup(CPM_CLK_FCC2, CPM_CLK14, CPM_CLK_TX);
+}
+
+static void __init ep8248_setup_arch(void)
+{
+ if (ppc_md.progress)
+ ppc_md.progress("ep8248_setup_arch()", 0);
+
+ cpm2_reset();
+
+ /* When this is set, snooping CPM DMA from RAM causes
+ * machine checks. See erratum SIU18.
+ */
+ clrbits32(&cpm2_immr->im_siu_conf.siu_82xx.sc_bcr, MPC82XX_BCR_PLDP);
+
+ ep8248e_bcsr_node =
+ of_find_compatible_node(NULL, NULL, "fsl,ep8248e-bcsr");
+ if (!ep8248e_bcsr_node) {
+ printk(KERN_ERR "No bcsr in device tree\n");
+ return;
+ }
+
+ ep8248e_bcsr = of_iomap(ep8248e_bcsr_node, 0);
+ if (!ep8248e_bcsr) {
+ printk(KERN_ERR "Cannot map BCSR registers\n");
+ return;
+ }
+
+ setbits8(&ep8248e_bcsr[7], BCSR7_SCC2_ENABLE);
+ setbits8(&ep8248e_bcsr[8], BCSR8_PHY1_ENABLE | BCSR8_PHY1_POWER |
+ BCSR8_PHY2_ENABLE | BCSR8_PHY2_POWER);
+
+ init_ioports();
+
+ if (ppc_md.progress)
+ ppc_md.progress("ep8248_setup_arch(), finish", 0);
+}
+
+static struct of_device_id __initdata of_bus_ids[] = {
+ { .name = "soc", },
+ { .name = "cpm", },
+ { .name = "localbus", },
+ { .compatible = "fsl,ep8248e-bcsr", },
+ {},
+};
+
+static int __init declare_of_platform_devices(void)
+{
+ if (!machine_is(ep8248))
+ return 0;
+
+ of_platform_bus_probe(NULL, of_bus_ids, NULL);
+ of_register_platform_driver(&ep8248e_mdio_driver);
+
+ return 0;
+}
+device_initcall(declare_of_platform_devices);
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init ep8248_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+ return of_flat_dt_is_compatible(root, "fsl,ep8248e");
+}
+
+define_machine(ep8248)
+{
+ .name = "Embedded Planet EP8248E",
+ .probe = ep8248_probe,
+ .setup_arch = ep8248_setup_arch,
+ .init_IRQ = ep8248_pic_init,
+ .get_irq = cpm2_get_irq,
+ .calibrate_decr = generic_calibrate_decr,
+ .restart = pq2_restart,
+ .progress = udbg_progress,
+};
diff --git a/include/asm-powerpc/mpc8260.h b/include/asm-powerpc/mpc8260.h
index e0d4807..03317e1 100644
--- a/include/asm-powerpc/mpc8260.h
+++ b/include/asm-powerpc/mpc8260.h
@@ -8,6 +8,7 @@
#ifndef __ASM_POWERPC_MPC8260_H__
#define __ASM_POWERPC_MPC8260_H__
+#define MPC82XX_BCR_PLDP 0x00800000 /* Pipeline Maximum Depth */
#ifdef CONFIG_8260
--
1.5.3.7
^ permalink raw reply related
* [PATCH v2 1/3] 8xx: Analogue & Micro Adder875 board support.
From: Scott Wood @ 2007-12-12 22:54 UTC (permalink / raw)
To: galak; +Cc: linuxppc-dev
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
Patch series resent according to feedback.
arch/powerpc/Kconfig | 3 +
arch/powerpc/boot/.gitignore | 1 +
arch/powerpc/boot/Makefile | 6 +-
arch/powerpc/boot/dts/adder875-redboot.dts | 165 +++++
arch/powerpc/boot/dts/adder875-uboot.dts | 175 +++++
arch/powerpc/boot/redboot-8xx.c | 58 ++
arch/powerpc/boot/redboot.h | 56 ++
arch/powerpc/boot/wrapper | 2 +-
arch/powerpc/configs/adder875-redboot_defconfig | 798 +++++++++++++++++++++++
arch/powerpc/configs/adder875-uboot_defconfig | 798 +++++++++++++++++++++++
arch/powerpc/platforms/8xx/Kconfig | 9 +
arch/powerpc/platforms/8xx/Makefile | 1 +
arch/powerpc/platforms/8xx/adder875.c | 123 ++++
13 files changed, 2193 insertions(+), 2 deletions(-)
create mode 100644 arch/powerpc/boot/dts/adder875-redboot.dts
create mode 100644 arch/powerpc/boot/dts/adder875-uboot.dts
create mode 100644 arch/powerpc/boot/redboot-8xx.c
create mode 100644 arch/powerpc/boot/redboot.h
create mode 100644 arch/powerpc/configs/adder875-redboot_defconfig
create mode 100644 arch/powerpc/configs/adder875-uboot_defconfig
create mode 100644 arch/powerpc/platforms/8xx/adder875.c
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index 232c298..88a6ebb 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -140,6 +140,9 @@ config DEFAULT_UIMAGE
Used to allow a board to specify it wants a uImage built by default
default n
+config REDBOOT
+ bool
+
config PPC64_SWSUSP
bool
depends on PPC64 && (BROKEN || (PPC_PMAC64 && EXPERIMENTAL))
diff --git a/arch/powerpc/boot/.gitignore b/arch/powerpc/boot/.gitignore
index 65f4118..a424be6 100644
--- a/arch/powerpc/boot/.gitignore
+++ b/arch/powerpc/boot/.gitignore
@@ -30,6 +30,7 @@ zImage.*lds
zImage.miboot
zImage.pmac
zImage.pseries
+zImage.redboot*
zImage.sandpoint
zImage.vmode
zconf.h
diff --git a/arch/powerpc/boot/Makefile b/arch/powerpc/boot/Makefile
index af01b4f..27b637c 100644
--- a/arch/powerpc/boot/Makefile
+++ b/arch/powerpc/boot/Makefile
@@ -58,7 +58,7 @@ src-plat := of.c cuboot-52xx.c cuboot-83xx.c cuboot-85xx.c holly.c \
cuboot-ebony.c treeboot-ebony.c prpmc2800.c \
ps3-head.S ps3-hvcall.S ps3.c treeboot-bamboo.c cuboot-8xx.c \
cuboot-pq2.c cuboot-sequoia.c treeboot-walnut.c cuboot-bamboo.c \
- fixed-head.S ep88xc.c cuboot-hpc2.c
+ fixed-head.S ep88xc.c cuboot-hpc2.c redboot-8xx.c
src-boot := $(src-wlib) $(src-plat) empty.c
src-boot := $(addprefix $(obj)/, $(src-boot))
@@ -165,6 +165,10 @@ image-$(CONFIG_SEQUOIA) += cuImage.sequoia
image-$(CONFIG_WALNUT) += treeImage.walnut
endif
+ifneq ($(CONFIG_REDBOOT),"")
+image-$(CONFIG_PPC_8xx) += zImage.redboot-8xx
+endif
+
# For 32-bit powermacs, build the COFF and miboot images
# as well as the ELF images.
ifeq ($(CONFIG_PPC32),y)
diff --git a/arch/powerpc/boot/dts/adder875-redboot.dts b/arch/powerpc/boot/dts/adder875-redboot.dts
new file mode 100644
index 0000000..4d28220
--- /dev/null
+++ b/arch/powerpc/boot/dts/adder875-redboot.dts
@@ -0,0 +1,165 @@
+/*
+ * Device Tree Source for MPC885 ADS running RedBoot
+ *
+ * Copyright 2006 MontaVista Software, Inc.
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+
+/ {
+ model = "Analogue & Micro Adder MPC875";
+ compatible = "analogue-and-micro,adder875";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,875@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <d#16>;
+ i-cache-line-size = <d#16>;
+ d-cache-size = <d#8192>;
+ i-cache-size = <d#8192>;
+ timebase-frequency = <0>;
+ bus-frequency = <0>;
+ clock-frequency = <0>;
+ interrupts = <f 2>; // decrementer interrupt
+ interrupt-parent = <&PIC>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 01000000>;
+ };
+
+ localbus@fa200100 {
+ compatible = "fsl,mpc885-localbus", "fsl,pq1-localbus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <fa200100 40>;
+
+ ranges = <
+ 0 0 fe000000 00800000
+ 2 0 fa100000 00008000
+ >;
+
+ flash@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 800000>;
+ bank-width = <4>;
+ device-width = <2>;
+ };
+ };
+
+ soc@fa200000 {
+ compatible = "fsl,mpc875", "fsl,pq1-soc";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ ranges = <0 fa200000 00004000>;
+
+ // Temporary until get_immrbase() is fixed.
+ reg = <fa200000 4000>;
+
+ mdio@e00 {
+ compatible = "fsl,mpc875-fec-mdio", "fsl,pq1-fec-mdio";
+ reg = <e00 188>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PHY0: ethernet-phy@0 {
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+
+ PHY1: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ ethernet@e00 {
+ device_type = "network";
+ compatible = "fsl,mpc875-fec-enet",
+ "fsl,pq1-fec-enet";
+ reg = <e00 188>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <3 1>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY0>;
+ linux,network-index = <0>;
+ };
+
+ ethernet@1e00 {
+ device_type = "network";
+ compatible = "fsl,mpc875-fec-enet",
+ "fsl,pq1-fec-enet";
+ reg = <1e00 188>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <7 1>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY1>;
+ linux,network-index = <1>;
+ };
+
+ PIC: interrupt-controller@0 {
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0 24>;
+ compatible = "fsl,mpc875-pic", "fsl,pq1-pic";
+ };
+
+ cpm@9c0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc875-cpm", "fsl,cpm1";
+ command-proc = <9c0>;
+ interrupts = <0>; // cpm error interrupt
+ interrupt-parent = <&CPM_PIC>;
+ reg = <9c0 40 2000 1c00>;
+ ranges;
+
+ brg@9f0 {
+ compatible = "fsl,mpc875-brg",
+ "fsl,cpm1-brg",
+ "fsl,cpm-brg";
+ reg = <9f0 10>;
+ };
+
+ CPM_PIC: interrupt-controller@930 {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupts = <5 2 0 2>;
+ interrupt-parent = <&PIC>;
+ reg = <930 20>;
+ compatible = "fsl,mpc875-cpm-pic",
+ "fsl,cpm1-pic";
+ };
+
+ serial@a80 {
+ device_type = "serial";
+ compatible = "fsl,mpc875-smc-uart",
+ "fsl,cpm1-smc-uart";
+ reg = <a80 10 3e80 40>;
+ interrupts = <4>;
+ interrupt-parent = <&CPM_PIC>;
+ fsl,cpm-brg = <1>;
+ fsl,cpm-command = <0090>;
+ current-speed = <115200>;
+ };
+ };
+ };
+
+ chosen {
+ linux,stdout-path = "/soc/cpm/serial@a80";
+ };
+};
diff --git a/arch/powerpc/boot/dts/adder875-uboot.dts b/arch/powerpc/boot/dts/adder875-uboot.dts
new file mode 100644
index 0000000..33d198c
--- /dev/null
+++ b/arch/powerpc/boot/dts/adder875-uboot.dts
@@ -0,0 +1,175 @@
+/*
+ * Device Tree Source for MPC885 ADS running U-Boot
+ *
+ * Copyright 2006 MontaVista Software, Inc.
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+
+/ {
+ model = "Analogue & Micro Adder MPC875";
+ compatible = "analogue-and-micro,adder875";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,875@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <d#16>;
+ i-cache-line-size = <d#16>;
+ d-cache-size = <d#8192>;
+ i-cache-size = <d#8192>;
+ timebase-frequency = <0>;
+ bus-frequency = <0>;
+ clock-frequency = <0>;
+ interrupts = <f 2>; // decrementer interrupt
+ interrupt-parent = <&PIC>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 01000000>;
+ };
+
+ localbus@ff000100 {
+ compatible = "fsl,mpc885-localbus", "fsl,pq1-localbus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <ff000100 40>;
+
+ ranges = <
+ 0 0 fe000000 01000000
+ >;
+
+ flash@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 800000>;
+ bank-width = <4>;
+ device-width = <2>;
+ };
+ };
+
+ soc@ff000000 {
+ compatible = "fsl,mpc875", "fsl,pq1-soc";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ ranges = <0 ff000000 00004000>;
+
+ // Temporary until get_immrbase() is fixed.
+ reg = <ff000000 4000>;
+
+ mdio@e00 {
+ compatible = "fsl,mpc875-fec-mdio", "fsl,pq1-fec-mdio";
+ reg = <e00 188>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PHY0: ethernet-phy@0 {
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+
+ PHY1: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ ethernet@e00 {
+ device_type = "network";
+ compatible = "fsl,mpc875-fec-enet",
+ "fsl,pq1-fec-enet";
+ reg = <e00 188>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <3 1>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY0>;
+ linux,network-index = <0>;
+ };
+
+ ethernet@1e00 {
+ device_type = "network";
+ compatible = "fsl,mpc875-fec-enet",
+ "fsl,pq1-fec-enet";
+ reg = <1e00 188>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <7 1>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY1>;
+ linux,network-index = <1>;
+ };
+
+ PIC: interrupt-controller@0 {
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0 24>;
+ compatible = "fsl,mpc875-pic", "fsl,pq1-pic";
+ };
+
+ cpm@9c0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc875-cpm", "fsl,cpm1";
+ command-proc = <9c0>;
+ interrupts = <0>; // cpm error interrupt
+ interrupt-parent = <&CPM_PIC>;
+ reg = <9c0 40>;
+ ranges;
+
+ muram {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 2000 2000>;
+
+ data@0 {
+ compatible = "fsl,cpm-muram-data";
+ reg = <0 1c00>;
+ };
+ };
+
+ brg@9f0 {
+ compatible = "fsl,mpc875-brg",
+ "fsl,cpm1-brg",
+ "fsl,cpm-brg";
+ reg = <9f0 10>;
+ };
+
+ CPM_PIC: interrupt-controller@930 {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupts = <5 2 0 2>;
+ interrupt-parent = <&PIC>;
+ reg = <930 20>;
+ compatible = "fsl,mpc875-cpm-pic",
+ "fsl,cpm1-pic";
+ };
+
+ serial@a80 {
+ device_type = "serial";
+ compatible = "fsl,mpc875-smc-uart",
+ "fsl,cpm1-smc-uart";
+ reg = <a80 10 3e80 40>;
+ interrupts = <4>;
+ interrupt-parent = <&CPM_PIC>;
+ fsl,cpm-brg = <1>;
+ fsl,cpm-command = <0090>;
+ current-speed = <115200>;
+ };
+ };
+ };
+
+ chosen {
+ linux,stdout-path = "/soc/cpm/serial@a80";
+ };
+};
diff --git a/arch/powerpc/boot/redboot-8xx.c b/arch/powerpc/boot/redboot-8xx.c
new file mode 100644
index 0000000..f7945ad
--- /dev/null
+++ b/arch/powerpc/boot/redboot-8xx.c
@@ -0,0 +1,58 @@
+/*
+ * RedBoot firmware support
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "redboot.h"
+#include "fsl-soc.h"
+#include "io.h"
+
+static bd_t bd;
+BSS_STACK(4096);
+
+#define MHZ(x) ((x + 500000) / 1000000)
+
+static void platform_fixups(void)
+{
+ void *node;
+
+ dt_fixup_memory(bd.bi_memstart, bd.bi_memsize);
+ dt_fixup_mac_addresses(bd.bi_enetaddr);
+ dt_fixup_cpu_clocks(bd.bi_intfreq, bd.bi_busfreq / 16, bd.bi_busfreq);
+
+ node = finddevice("/soc/cpm/brg");
+ if (node) {
+ printf("BRG clock-frequency <- 0x%x (%dMHz)\r\n",
+ bd.bi_busfreq, MHZ(bd.bi_busfreq));
+ setprop(node, "clock-frequency", &bd.bi_busfreq, 4);
+ }
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+ unsigned long r6, unsigned long r7)
+{
+ memcpy(&bd, (char *)r3, sizeof(bd));
+
+ if (bd.bi_tag != 0x42444944)
+ return;
+
+ simple_alloc_init(_end,
+ bd.bi_memstart + bd.bi_memsize - (unsigned long)_end,
+ 32, 64);
+
+ fdt_init(_dtb_start);
+ serial_console_init();
+ platform_ops.fixups = platform_fixups;
+
+ loader_info.cmdline = (char *)bd.bi_cmdline;
+ loader_info.cmdline_len = strlen((char *)bd.bi_cmdline);
+}
diff --git a/arch/powerpc/boot/redboot.h b/arch/powerpc/boot/redboot.h
new file mode 100644
index 0000000..ace0b7f
--- /dev/null
+++ b/arch/powerpc/boot/redboot.h
@@ -0,0 +1,56 @@
+#ifndef _PPC_REDBOOT_H
+#define _PPC_REDBOOT_H
+
+//=========================================================================
+// include/asm-ppc/redboot.h
+// Copyright (c) 2002, 2003 Gary Thomas (<gary@mlbassoc.com>
+// Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
+
+//
+// Board specific details, as provided by RedBoot
+//
+
+/* A Board Information structure that is given to a program when
+ * RedBoot starts it up. Note: not all fields make sense for all
+ * architectures and it's up to the platform specific code to fill
+ * in the details.
+ */
+typedef struct bd_info {
+ unsigned int bi_tag; /* Should be 0x42444944 "BDID" */
+ unsigned int bi_size; /* Size of this structure */
+ unsigned int bi_revision; /* revision of this structure */
+ unsigned int bi_bdate; /* bootstrap date, i.e. 0x19971106 */
+ unsigned int bi_memstart; /* Memory start address */
+ unsigned int bi_memsize; /* Memory (end) size in bytes */
+ unsigned int bi_intfreq; /* Internal Freq, in Hz */
+ unsigned int bi_busfreq; /* Bus Freq, in Hz */
+ unsigned int bi_cpmfreq; /* CPM Freq, in Hz */
+ unsigned int bi_brgfreq; /* BRG Freq, in Hz */
+ unsigned int bi_vco; /* VCO Out from PLL */
+ unsigned int bi_pci_freq; /* PCI Freq, in Hz */
+ unsigned int bi_baudrate; /* Default console baud rate */
+ unsigned int bi_immr; /* IMMR when called from boot rom */
+ unsigned char bi_enetaddr[6];
+ unsigned int bi_flashbase; /* Physical address of FLASH memory */
+ unsigned int bi_flashsize; /* Length of FLASH memory */
+ int bi_flashwidth; /* Width (8,16,32,64) */
+ unsigned char *bi_cmdline; /* Pointer to command line */
+ unsigned char bi_esa[3][6]; /* Ethernet station addresses */
+ unsigned int bi_ramdisk_begin, bi_ramdisk_end;
+ struct { /* Information about [main] video screen */
+ short x_res; /* Horizontal resolution in pixels */
+ short y_res; /* Vertical resolution in pixels */
+ short bpp; /* Bits/pixel */
+ short mode; /* Type of pixels (packed, indexed) */
+ unsigned long fb; /* Pointer to frame buffer (pixel) memory */
+ } bi_video;
+ void (*bi_cputc)(char); /* Write a character to the RedBoot console */
+ char (*bi_cgetc)(void); /* Read a character from the RedBoot console */
+ int (*bi_ctstc)(void); /* Test for input on the RedBoot console */
+} bd_t;
+
+#define BI_REV 0x0102 /* Version 1.02 */
+
+#define bi_pci_busfreq bi_pci_freq
+#define bi_immr_base bi_immr
+#endif
diff --git a/arch/powerpc/boot/wrapper b/arch/powerpc/boot/wrapper
index a591ced..68fde3d 100755
--- a/arch/powerpc/boot/wrapper
+++ b/arch/powerpc/boot/wrapper
@@ -168,7 +168,7 @@ ps3)
ksection=.kernel:vmlinux.bin
isection=.kernel:initrd
;;
-ep88xc)
+ep88xc|redboot*)
platformo="$object/fixed-head.o $object/$platform.o"
binary=y
;;
diff --git a/arch/powerpc/configs/adder875-redboot_defconfig b/arch/powerpc/configs/adder875-redboot_defconfig
new file mode 100644
index 0000000..74fd6a4
--- /dev/null
+++ b/arch/powerpc/configs/adder875-redboot_defconfig
@@ -0,0 +1,798 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.24-rc3
+# Mon Dec 10 11:29:32 2007
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+# CONFIG_6xx is not set
+# CONFIG_PPC_85xx is not set
+CONFIG_PPC_8xx=y
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_8xx=y
+# CONFIG_PPC_MM_SLICES is not set
+CONFIG_NOT_COHERENT_CACHE=y
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+# CONFIG_PPC_UDBG_16550 is not set
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+CONFIG_REDBOOT=y
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+# CONFIG_BLK_DEV_INITRD is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+# CONFIG_SYSCTL_SYSCALL is not set
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+# CONFIG_ELF_CORE is not set
+# CONFIG_BASE_FULL is not set
+# CONFIG_FUTEX is not set
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+CONFIG_SLUB_DEBUG=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=1
+# CONFIG_MODULES is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_AS is not set
+CONFIG_IOSCHED_DEADLINE=y
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_DEFAULT_AS is not set
+CONFIG_DEFAULT_DEADLINE=y
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="deadline"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+CONFIG_CPM1=y
+# CONFIG_MPC8XXFADS is not set
+# CONFIG_MPC86XADS is not set
+# CONFIG_MPC885ADS is not set
+# CONFIG_PPC_EP88XC is not set
+CONFIG_PPC_ADDER875=y
+
+#
+# MPC8xx CPM Options
+#
+
+#
+# Generic MPC8xx Options
+#
+CONFIG_8xx_COPYBACK=y
+# CONFIG_8xx_CPU6 is not set
+CONFIG_8xx_CPU15=y
+CONFIG_NO_UCODE_PATCH=y
+# CONFIG_USB_SOF_UCODE_PATCH is not set
+# CONFIG_I2C_SPI_UCODE_PATCH is not set
+# CONFIG_I2C_SPI_SMC1_UCODE_PATCH is not set
+# CONFIG_PQ2ADS is not set
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPM2 is not set
+CONFIG_PPC_CPM_NEW_BINDING=y
+# CONFIG_FSL_ULI1575 is not set
+CONFIG_CPM=y
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+# CONFIG_HZ_250 is not set
+# CONFIG_HZ_300 is not set
+CONFIG_HZ_1000=y
+CONFIG_HZ=1000
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_MATH_EMULATION is not set
+# CONFIG_8XX_MINIMAL_FPEMU is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+# CONFIG_PROC_DEVICETREE is not set
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
+# CONFIG_SECCOMP is not set
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE="adder875-redboot.dts"
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_FSL_SOC=y
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_PCI_QSPAN is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_START=0xfd000000
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_BOOT_LOAD=0x00400000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+# CONFIG_IP_PNP_DHCP is not set
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+# CONFIG_MTD_PARTITIONS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_CFI_FLAGADM is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+# CONFIG_BLK_DEV is not set
+# CONFIG_MISC_DEVICES is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+CONFIG_DAVICOM_PHY=y
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_B44 is not set
+CONFIG_FS_ENET=y
+# CONFIG_FS_ENET_HAS_SCC is not set
+CONFIG_FS_ENET_HAS_FEC=y
+CONFIG_FS_ENET_MDIO_FEC=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_KEYBOARD_ATKBD=y
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_LIFEBOOK=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_I8042=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_CPM=y
+CONFIG_SERIAL_CPM_CONSOLE=y
+# CONFIG_SERIAL_CPM_SCC1 is not set
+# CONFIG_SERIAL_CPM_SCC2 is not set
+# CONFIG_SERIAL_CPM_SCC3 is not set
+# CONFIG_SERIAL_CPM_SCC4 is not set
+CONFIG_SERIAL_CPM_SMC1=y
+CONFIG_SERIAL_CPM_SMC2=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=y
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+# CONFIG_EXT2_FS is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_INOTIFY is not set
+# CONFIG_QUOTA is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+# CONFIG_PROC_KCORE is not set
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS2_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+# CONFIG_NLS is not set
+# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+# CONFIG_CRC32 is not set
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_INSTRUMENTATION=y
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_BDI_SWITCH is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+# CONFIG_CRYPTO is not set
+# CONFIG_PPC_CLOCK is not set
+CONFIG_PPC_LIB_RHEAP=y
diff --git a/arch/powerpc/configs/adder875-uboot_defconfig b/arch/powerpc/configs/adder875-uboot_defconfig
new file mode 100644
index 0000000..d5ebb25
--- /dev/null
+++ b/arch/powerpc/configs/adder875-uboot_defconfig
@@ -0,0 +1,798 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.24-rc3
+# Mon Dec 10 11:29:32 2007
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+# CONFIG_6xx is not set
+# CONFIG_PPC_85xx is not set
+CONFIG_PPC_8xx=y
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_8xx=y
+# CONFIG_PPC_MM_SLICES is not set
+CONFIG_NOT_COHERENT_CACHE=y
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+# CONFIG_PPC_UDBG_16550 is not set
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+CONFIG_REDBOOT=y
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+# CONFIG_BLK_DEV_INITRD is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+# CONFIG_SYSCTL_SYSCALL is not set
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+# CONFIG_ELF_CORE is not set
+# CONFIG_BASE_FULL is not set
+# CONFIG_FUTEX is not set
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+CONFIG_SLUB_DEBUG=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=1
+# CONFIG_MODULES is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_AS is not set
+CONFIG_IOSCHED_DEADLINE=y
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_DEFAULT_AS is not set
+CONFIG_DEFAULT_DEADLINE=y
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="deadline"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+CONFIG_CPM1=y
+# CONFIG_MPC8XXFADS is not set
+# CONFIG_MPC86XADS is not set
+# CONFIG_MPC885ADS is not set
+# CONFIG_PPC_EP88XC is not set
+CONFIG_PPC_ADDER875=y
+
+#
+# MPC8xx CPM Options
+#
+
+#
+# Generic MPC8xx Options
+#
+CONFIG_8xx_COPYBACK=y
+# CONFIG_8xx_CPU6 is not set
+CONFIG_8xx_CPU15=y
+CONFIG_NO_UCODE_PATCH=y
+# CONFIG_USB_SOF_UCODE_PATCH is not set
+# CONFIG_I2C_SPI_UCODE_PATCH is not set
+# CONFIG_I2C_SPI_SMC1_UCODE_PATCH is not set
+# CONFIG_PQ2ADS is not set
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPM2 is not set
+CONFIG_PPC_CPM_NEW_BINDING=y
+# CONFIG_FSL_ULI1575 is not set
+CONFIG_CPM=y
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+# CONFIG_HZ_250 is not set
+# CONFIG_HZ_300 is not set
+CONFIG_HZ_1000=y
+CONFIG_HZ=1000
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_MATH_EMULATION is not set
+# CONFIG_8XX_MINIMAL_FPEMU is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+# CONFIG_PROC_DEVICETREE is not set
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
+# CONFIG_SECCOMP is not set
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE="adder875-uboot.dts"
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_FSL_SOC=y
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_PCI_QSPAN is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_START=0xfd000000
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_BOOT_LOAD=0x00400000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+# CONFIG_IP_PNP_DHCP is not set
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+# CONFIG_MTD_PARTITIONS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_CFI_FLAGADM is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+# CONFIG_BLK_DEV is not set
+# CONFIG_MISC_DEVICES is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+CONFIG_DAVICOM_PHY=y
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_B44 is not set
+CONFIG_FS_ENET=y
+# CONFIG_FS_ENET_HAS_SCC is not set
+CONFIG_FS_ENET_HAS_FEC=y
+CONFIG_FS_ENET_MDIO_FEC=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_KEYBOARD_ATKBD=y
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_LIFEBOOK=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_I8042=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_CPM=y
+CONFIG_SERIAL_CPM_CONSOLE=y
+# CONFIG_SERIAL_CPM_SCC1 is not set
+# CONFIG_SERIAL_CPM_SCC2 is not set
+# CONFIG_SERIAL_CPM_SCC3 is not set
+# CONFIG_SERIAL_CPM_SCC4 is not set
+CONFIG_SERIAL_CPM_SMC1=y
+CONFIG_SERIAL_CPM_SMC2=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=y
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+# CONFIG_EXT2_FS is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_INOTIFY is not set
+# CONFIG_QUOTA is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+# CONFIG_PROC_KCORE is not set
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS2_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+# CONFIG_NLS is not set
+# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+# CONFIG_CRC32 is not set
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_INSTRUMENTATION=y
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_BDI_SWITCH is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+# CONFIG_CRYPTO is not set
+# CONFIG_PPC_CLOCK is not set
+CONFIG_PPC_LIB_RHEAP=y
diff --git a/arch/powerpc/platforms/8xx/Kconfig b/arch/powerpc/platforms/8xx/Kconfig
index bd28655..cfa0001 100644
--- a/arch/powerpc/platforms/8xx/Kconfig
+++ b/arch/powerpc/platforms/8xx/Kconfig
@@ -43,6 +43,15 @@ config PPC_EP88XC
This board is also resold by Freescale as the QUICCStart
MPC885 Evaluation System and/or the CWH-PPC-885XN-VE.
+config PPC_ADDER875
+ bool "Analogue & Micro Adder 875"
+ select CPM1
+ select PPC_CPM_NEW_BINDING
+ select REDBOOT
+ help
+ This enables support for the Analogue & Micro Adder 875
+ board.
+
endchoice
menu "Freescale Ethernet driver platform-specific options"
diff --git a/arch/powerpc/platforms/8xx/Makefile b/arch/powerpc/platforms/8xx/Makefile
index 8b70980..7b71d9c 100644
--- a/arch/powerpc/platforms/8xx/Makefile
+++ b/arch/powerpc/platforms/8xx/Makefile
@@ -5,3 +5,4 @@ obj-$(CONFIG_PPC_8xx) += m8xx_setup.o
obj-$(CONFIG_MPC885ADS) += mpc885ads_setup.o
obj-$(CONFIG_MPC86XADS) += mpc86xads_setup.o
obj-$(CONFIG_PPC_EP88XC) += ep88xc.o
+obj-$(CONFIG_PPC_ADDER875) += adder875.o
diff --git a/arch/powerpc/platforms/8xx/adder875.c b/arch/powerpc/platforms/8xx/adder875.c
new file mode 100644
index 0000000..3a3bb2b
--- /dev/null
+++ b/arch/powerpc/platforms/8xx/adder875.c
@@ -0,0 +1,123 @@
+/* Analogue & Micro Adder MPC875 board support
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/fs_enet_pd.h>
+#include <linux/of_platform.h>
+
+#include <asm/time.h>
+#include <asm/machdep.h>
+#include <asm/commproc.h>
+#include <asm/fs_pd.h>
+#include <asm/udbg.h>
+#include <asm/prom.h>
+
+#include <sysdev/commproc.h>
+
+struct cpm_pin {
+ int port, pin, flags;
+};
+
+static const struct cpm_pin adder875_pins[] = {
+ /* SMC1 */
+ {CPM_PORTB, 24, CPM_PIN_INPUT}, /* RX */
+ {CPM_PORTB, 25, CPM_PIN_INPUT | CPM_PIN_SECONDARY}, /* TX */
+
+ /* MII1 */
+ {CPM_PORTA, 0, CPM_PIN_INPUT},
+ {CPM_PORTA, 1, CPM_PIN_INPUT},
+ {CPM_PORTA, 2, CPM_PIN_INPUT},
+ {CPM_PORTA, 3, CPM_PIN_INPUT},
+ {CPM_PORTA, 4, CPM_PIN_OUTPUT},
+ {CPM_PORTA, 10, CPM_PIN_OUTPUT},
+ {CPM_PORTA, 11, CPM_PIN_OUTPUT},
+ {CPM_PORTB, 19, CPM_PIN_INPUT},
+ {CPM_PORTB, 31, CPM_PIN_INPUT},
+ {CPM_PORTC, 12, CPM_PIN_INPUT},
+ {CPM_PORTC, 13, CPM_PIN_INPUT},
+ {CPM_PORTE, 30, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 31, CPM_PIN_OUTPUT},
+
+ /* MII2 */
+ {CPM_PORTE, 14, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {CPM_PORTE, 15, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {CPM_PORTE, 16, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 17, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {CPM_PORTE, 18, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {CPM_PORTE, 19, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {CPM_PORTE, 20, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {CPM_PORTE, 21, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 22, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 23, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 24, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 25, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 26, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 27, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 28, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 29, CPM_PIN_OUTPUT},
+};
+
+static void __init init_ioports(void)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(adder875_pins); i++) {
+ const struct cpm_pin *pin = &adder875_pins[i];
+ cpm1_set_pin(pin->port, pin->pin, pin->flags);
+ }
+
+ cpm1_clk_setup(CPM_CLK_SMC1, CPM_BRG1, CPM_CLK_RTX);
+
+ /* Set FEC1 and FEC2 to MII mode */
+ clrbits32(&mpc8xx_immr->im_cpm.cp_cptr, 0x00000180);
+}
+
+static void __init adder875_setup(void)
+{
+ cpm_reset();
+ init_ioports();
+}
+
+static int __init adder875_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+ return of_flat_dt_is_compatible(root, "analogue-and-micro,adder875");
+}
+
+static struct of_device_id __initdata of_bus_ids[] = {
+ { .name = "soc", },
+ { .name = "cpm", },
+ { .name = "localbus", },
+ {},
+};
+
+static int __init declare_of_platform_devices(void)
+{
+ /* Publish the QE devices */
+ if (machine_is(adder875))
+ of_platform_bus_probe(NULL, of_bus_ids, NULL);
+
+ return 0;
+}
+device_initcall(declare_of_platform_devices);
+
+define_machine(adder875) {
+ .name = "Adder MPC875",
+ .probe = adder875_probe,
+ .setup_arch = adder875_setup,
+ .init_IRQ = m8xx_pic_init,
+ .get_irq = mpc8xx_get_irq,
+ .restart = mpc8xx_restart,
+ .calibrate_decr = generic_calibrate_decr,
+ .set_rtc_time = mpc8xx_set_rtc_time,
+ .get_rtc_time = mpc8xx_get_rtc_time,
+ .progress = udbg_progress,
+};
--
1.5.3.7
^ permalink raw reply related
* Re: [PATCH 1/2] Make setjmp/longjmp code generic
From: Michael Ellerman @ 2007-12-12 22:56 UTC (permalink / raw)
To: Michael Neuling; +Cc: linuxppc-dev, RAISCH, Paul Mackerras, THEMANN
In-Reply-To: <20071212054512.882AC62C070@localhost.localdomain>
[-- Attachment #1: Type: text/plain, Size: 3401 bytes --]
On Wed, 2007-12-12 at 16:45 +1100, Michael Neuling wrote:
> This makes the setjmp/longjmp code used by xmon, generically available
> to other code. It also removes the requirement for debugger hooks to
> be only called on 0x300 (data storage) exception.
>
> Signed-off-by: Michael Neuling <mikey@neuling.org>
> ---
>
> arch/powerpc/kernel/misc_64.S | 124 ++++++++++++++++++++++++++++++++++++++
> arch/powerpc/mm/fault.c | 6 -
> arch/powerpc/xmon/Makefile | 2
> arch/powerpc/xmon/setjmp.S | 135 ------------------------------------------
> arch/powerpc/xmon/xmon.c | 10 ---
> include/asm-powerpc/setjmp.h | 12 +++
> 6 files changed, 142 insertions(+), 147 deletions(-)
>
> Index: linux-2.6-ozlabs/arch/powerpc/kernel/misc_64.S
> ===================================================================
> --- linux-2.6-ozlabs.orig/arch/powerpc/kernel/misc_64.S
> +++ linux-2.6-ozlabs/arch/powerpc/kernel/misc_64.S
> @@ -518,6 +518,130 @@ _GLOBAL(giveup_altivec)
>
> #endif /* CONFIG_ALTIVEC */
>
> +_GLOBAL(setjmp)
> + mflr r0
> + PPC_STL r0,0(r3)
> + PPC_STL r1,SZL(r3)
> + PPC_STL r2,2*SZL(r3)
> + mfcr r0
> + PPC_STL r0,3*SZL(r3)
> + PPC_STL r13,4*SZL(r3)
> + PPC_STL r14,5*SZL(r3)
> + PPC_STL r15,6*SZL(r3)
> + PPC_STL r16,7*SZL(r3)
> + PPC_STL r17,8*SZL(r3)
> + PPC_STL r18,9*SZL(r3)
> + PPC_STL r19,10*SZL(r3)
> + PPC_STL r20,11*SZL(r3)
> + PPC_STL r21,12*SZL(r3)
> + PPC_STL r22,13*SZL(r3)
> + PPC_STL r23,14*SZL(r3)
> + PPC_STL r24,15*SZL(r3)
> + PPC_STL r25,16*SZL(r3)
> + PPC_STL r26,17*SZL(r3)
> + PPC_STL r27,18*SZL(r3)
> + PPC_STL r28,19*SZL(r3)
> + PPC_STL r29,20*SZL(r3)
> + PPC_STL r30,21*SZL(r3)
> + PPC_STL r31,22*SZL(r3)
> + li r3,0
> + blr
> +
> +_GLOBAL(longjmp)
> + PPC_LCMPI r4,0
> + bne 1f
> + li r4,1
> +1: PPC_LL r13,4*SZL(r3)
> + PPC_LL r14,5*SZL(r3)
> + PPC_LL r15,6*SZL(r3)
> + PPC_LL r16,7*SZL(r3)
> + PPC_LL r17,8*SZL(r3)
> + PPC_LL r18,9*SZL(r3)
> + PPC_LL r19,10*SZL(r3)
> + PPC_LL r20,11*SZL(r3)
> + PPC_LL r21,12*SZL(r3)
> + PPC_LL r22,13*SZL(r3)
> + PPC_LL r23,14*SZL(r3)
> + PPC_LL r24,15*SZL(r3)
> + PPC_LL r25,16*SZL(r3)
> + PPC_LL r26,17*SZL(r3)
> + PPC_LL r27,18*SZL(r3)
> + PPC_LL r28,19*SZL(r3)
> + PPC_LL r29,20*SZL(r3)
> + PPC_LL r30,21*SZL(r3)
> + PPC_LL r31,22*SZL(r3)
> + PPC_LL r0,3*SZL(r3)
> + mtcrf 0x38,r0
> + PPC_LL r0,0(r3)
> + PPC_LL r1,SZL(r3)
> + PPC_LL r2,2*SZL(r3)
> + mtlr r0
> + mr r3,r4
> + blr
> +
> +#ifdef CONFIG_XMON
> +/*
> + * Grab the register values as they are now.
> + * This won't do a particularily good job because we really
> + * want our caller's caller's registers, and our caller has
> + * already executed its prologue.
> + * ToDo: We could reach back into the caller's save area to do
> + * a better job of representing the caller's state (note that
> + * that will be different for 32-bit and 64-bit, because of the
> + * different ABIs, though).
> + */
> +_GLOBAL(xmon_save_regs)
> + PPC_STL r0,0*SZL(r3)
> + PPC_STL r2,2*SZL(r3)
> + PPC_STL r3,3*SZL(r3)
> + PPC_STL r4,4*SZL(r3)
Does xmon_save_regs belong here?
cheers
--
Michael Ellerman
OzLabs, IBM Australia Development Lab
wwweb: http://michael.ellerman.id.au
phone: +61 2 6212 1183 (tie line 70 21183)
We do not inherit the earth from our ancestors,
we borrow it from our children. - S.M.A.R.T Person
[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply
* Re: [PATCH 4/8] fsl_soc: Factor fsl_get_sys_freq() out of the wdt init.
From: Stephen Rothwell @ 2007-12-12 23:01 UTC (permalink / raw)
To: Scott Wood; +Cc: linuxppc-dev, paulus
In-Reply-To: <20071212173601.GC5596@loki.buserror.net>
[-- Attachment #1: Type: text/plain, Size: 457 bytes --]
Hi Scott,
Just one little nit ...
On Wed, 12 Dec 2007 11:36:01 -0600 Scott Wood <scottwood@freescale.com> wrote:
>
> - ret = platform_device_add_data(dev, freq, sizeof(int));
> + ret = platform_device_add_data(dev, &freq, sizeof(int));
^^^
Surely you want "u32" or "freg" here?
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
http://www.canb.auug.org.au/~sfr/
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply
* Re: [PATCH 2/2] kdump shutdown hook support
From: Michael Ellerman @ 2007-12-12 23:07 UTC (permalink / raw)
To: Michael Neuling; +Cc: linuxppc-dev, RAISCH, Paul Mackerras, THEMANN
In-Reply-To: <20071212054512.A02B062C153@localhost.localdomain>
[-- Attachment #1: Type: text/plain, Size: 4958 bytes --]
On Wed, 2007-12-12 at 16:45 +1100, Michael Neuling wrote:
> This adds hooks into the default_machine_crash_shutdown so drivers can
> register a function to be run in the first kernel before we hand off
> to the second kernel. This should only be used in exceptional
> circumstances, like where the device can't be reset in the second
> kernel alone (as is the case with eHEA). To emphasize this, the
> number of handles allowed to be registered is currently #def to 1.
>
> This uses the setjmp/longjmp code to call out to the registered hooks,
> so any bogus exceptions we encounter will hopefully be recoverable.
>
> I've tested with bogus data and instruction exceptions.
>
> Signed-off-by: Michael Neuling <mikey@neuling.org>
> ---
>
> arch/powerpc/kernel/crash.c | 90 +++++++++++++++++++++++++++++++++++++++++---
> include/asm-powerpc/kexec.h | 3 +
> 2 files changed, 88 insertions(+), 5 deletions(-)
>
> Index: linux-2.6-ozlabs/arch/powerpc/kernel/crash.c
> ===================================================================
> --- linux-2.6-ozlabs.orig/arch/powerpc/kernel/crash.c
> +++ linux-2.6-ozlabs/arch/powerpc/kernel/crash.c
> @@ -32,6 +32,8 @@
> #include <asm/lmb.h>
> #include <asm/firmware.h>
> #include <asm/smp.h>
> +#include <asm/system.h>
> +#include <asm/setjmp.h>
>
> #ifdef DEBUG
> #include <asm/udbg.h>
> @@ -45,6 +47,11 @@ int crashing_cpu = -1;
> static cpumask_t cpus_in_crash = CPU_MASK_NONE;
> cpumask_t cpus_in_sr = CPU_MASK_NONE;
>
> +#define CRASH_SHUTDOWN_HANDLES_NUM 1
CRASH_HANDLER_MAX ?
> +/* NULL terminated list of shutdown handles */
> +static crash_shutdown_t crash_shutdown_handles[CRASH_SHUTDOWN_HANDLES_NUM+1];
> +static DEFINE_SPINLOCK(crash_handles_lock);
> +
> #ifdef CONFIG_SMP
> static atomic_t enter_on_soft_reset = ATOMIC_INIT(0);
>
> @@ -285,9 +292,69 @@ static inline void crash_kexec_stop_spus
> }
> #endif /* CONFIG_SPU_BASE */
>
> +/*
> + * Register a function to be called on shutdown. Only use this if you
> + * can't reset your device in the second kernel.
> + */
> +int crash_shutdown_register(crash_shutdown_t handler)
> +{
> + unsigned int i, rc;
> +
> + spin_lock(&crash_handles_lock);
> + for(i = 0 ; i <= CRASH_SHUTDOWN_HANDLES_NUM; i++) {
> + if (!crash_shutdown_handles[i]) {
> + /* Insert handle at end */
> + crash_shutdown_handles[i] = handler;
> + rc = 0;
> + break;
> + }
> + }
>
> + if (i == CRASH_SHUTDOWN_HANDLES_NUM){
> + printk(KERN_ERR "Crash shutdown handles full, "
> + "not registered.\n");
> + rc = 1;
> + }
> +
> + spin_unlock(&crash_handles_lock);
Perhaps?
> + return rc;
> +}
> +EXPORT_SYMBOL(crash_shutdown_register);
> +
> +int crash_shutdown_unregister(crash_shutdown_t handler)
> +{
> + unsigned int i;
> +
> + spin_lock(&crash_handles_lock);
> + for(i = 0 ; i <= CRASH_SHUTDOWN_HANDLES_NUM; i++)
> + if (crash_shutdown_handles[i] == handler)
> + break;
> +
> + if (i == CRASH_SHUTDOWN_HANDLES_NUM){
> + printk(KERN_ERR "Crash shutdown handle not found\n");
> + spin_unlock(&crash_handles_lock);
> + return 1;
> + }
> +
> + /* Shift handles down */
> + while(crash_shutdown_handles[i]) {
> + crash_shutdown_handles[i] = crash_shutdown_handles[i+1];
> + i++;
> + }
> + spin_unlock(&crash_handles_lock);
> + return 0;
> +}
> +EXPORT_SYMBOL(crash_shutdown_unregister);
> +
> +static long crash_shutdown_buf[SETJMP_BUF_LEN];
unsigned long?
> +
> +static int handle_fault(struct pt_regs *regs)
> +{
> + longjmp(crash_shutdown_buf, 1);
> + return 0;
> +}
> +
> void default_machine_crash_shutdown(struct pt_regs *regs)
> {
> - unsigned int irq;
> + unsigned int i;
>
> /*
> * This function is only called after the system
> @@ -301,14 +368,27 @@ void default_machine_crash_shutdown(stru
> */
> hard_irq_disable();
>
> - for_each_irq(irq) {
> - struct irq_desc *desc = irq_desc + irq;
> + for_each_irq(i) {
> + struct irq_desc *desc = irq_desc + i;
>
> if (desc->status & IRQ_INPROGRESS)
> - desc->chip->eoi(irq);
> + desc->chip->eoi(i);
>
> if (!(desc->status & IRQ_DISABLED))
> - desc->chip->disable(irq);
> + desc->chip->disable(i);
> + }
> +
> + /* Call registered shutdown routines */
> + __debugger_fault_handler = handle_fault;
> + i = 0;
> + while(crash_shutdown_handles[i]){
> + if (setjmp(crash_shutdown_buf) == 0) {
> + asm volatile("sync; isync");
> + crash_shutdown_handles[i]();
> + asm volatile("sync; isync");
> + __delay(200);
> + }
> + i++;
> }
You should probably reset __debugger_fault_handler, just to be safe.
cheers
--
Michael Ellerman
OzLabs, IBM Australia Development Lab
wwweb: http://michael.ellerman.id.au
phone: +61 2 6212 1183 (tie line 70 21183)
We do not inherit the earth from our ancestors,
we borrow it from our children. - S.M.A.R.T Person
[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply
* Re: [PATCH v2] [POWERPC] pasemi: Implement MSI support
From: Michael Ellerman @ 2007-12-12 23:18 UTC (permalink / raw)
To: Olof Johansson; +Cc: linuxppc-dev
In-Reply-To: <1197499871.7695.9.camel@concordia>
[-- Attachment #1: Type: text/plain, Size: 526 bytes --]
On Thu, 2007-12-13 at 09:51 +1100, Michael Ellerman wrote:
> On Wed, 2007-12-12 at 01:23 -0600, Olof Johansson wrote:
>
> Patch looks good otherwise.
By which I mean:
Acked-by: Michael Ellerman <michael@ellerman.id.au>
This patch is double-plus-good!
cheers
--
Michael Ellerman
OzLabs, IBM Australia Development Lab
wwweb: http://michael.ellerman.id.au
phone: +61 2 6212 1183 (tie line 70 21183)
We do not inherit the earth from our ancestors,
we borrow it from our children. - S.M.A.R.T Person
[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply
* Re: [PATCH 1/2] Make setjmp/longjmp code generic
From: Michael Neuling @ 2007-12-12 23:40 UTC (permalink / raw)
To: michael; +Cc: linuxppc-dev, RAISCH, Paul Mackerras, THEMANN
In-Reply-To: <1197500215.7695.11.camel@concordia>
> > arch/powerpc/xmon/setjmp.S | 135 ------------------------------------------
<snip>
> > +#ifdef CONFIG_XMON
> > +/*
> > + * Grab the register values as they are now.
> > + * This won't do a particularily good job because we really
> > + * want our caller's caller's registers, and our caller has
> > + * already executed its prologue.
> > + * ToDo: We could reach back into the caller's save area to do
> > + * a better job of representing the caller's state (note that
> > + * that will be different for 32-bit and 64-bit, because of the
> > + * different ABIs, though).
> > + */
> > +_GLOBAL(xmon_save_regs)
> > + PPC_STL r0,0*SZL(r3)
> > + PPC_STL r2,2*SZL(r3)
> > + PPC_STL r3,3*SZL(r3)
> > + PPC_STL r4,4*SZL(r3)
>
> Does xmon_save_regs belong here?
This was the only function left in xmon/setjmp.S. So rather than rename
the whole file to reflect it no longer has anything to do with setjmp, I
moved it out to misc.S
I'm not fussed what we end up doing.
Mikey
^ permalink raw reply
* Re: [PATCH 2/2] kdump shutdown hook support
From: Michael Neuling @ 2007-12-13 0:04 UTC (permalink / raw)
To: michael; +Cc: linuxppc-dev, RAISCH, Paul Mackerras, THEMANN
In-Reply-To: <1197500839.7695.19.camel@concordia>
In message <1197500839.7695.19.camel@concordia> you wrote:
>
> --=-Kza0KCx0MG8nsjfq7kOz
> Content-Type: text/plain
> Content-Transfer-Encoding: quoted-printable
>
> On Wed, 2007-12-12 at 16:45 +1100, Michael Neuling wrote:
> > This adds hooks into the default_machine_crash_shutdown so drivers can
> > register a function to be run in the first kernel before we hand off
> > to the second kernel. This should only be used in exceptional
> > circumstances, like where the device can't be reset in the second
> > kernel alone (as is the case with eHEA). To emphasize this, the
> > number of handles allowed to be registered is currently #def to 1.
> >=20
> > This uses the setjmp/longjmp code to call out to the registered hooks,
> > so any bogus exceptions we encounter will hopefully be recoverable. =20
> >=20
> > I've tested with bogus data and instruction exceptions.
> >=20
> > Signed-off-by: Michael Neuling <mikey@neuling.org>
> > ---
> >=20
> > arch/powerpc/kernel/crash.c | 90 +++++++++++++++++++++++++++++++++++++=
> ++++---
> > include/asm-powerpc/kexec.h | 3 +
> > 2 files changed, 88 insertions(+), 5 deletions(-)
> >=20
> > Index: linux-2.6-ozlabs/arch/powerpc/kernel/crash.c
> > =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
> =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
> =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
> > --- linux-2.6-ozlabs.orig/arch/powerpc/kernel/crash.c
> > +++ linux-2.6-ozlabs/arch/powerpc/kernel/crash.c
> > @@ -32,6 +32,8 @@
> > #include <asm/lmb.h>
> > #include <asm/firmware.h>
> > #include <asm/smp.h>
> > +#include <asm/system.h>
> > +#include <asm/setjmp.h>
> > =20
> > #ifdef DEBUG
> > #include <asm/udbg.h>
> > @@ -45,6 +47,11 @@ int crashing_cpu =3D -1;
> > static cpumask_t cpus_in_crash =3D CPU_MASK_NONE;
> > cpumask_t cpus_in_sr =3D CPU_MASK_NONE;
> > =20
> > +#define CRASH_SHUTDOWN_HANDLES_NUM 1
>
> CRASH_HANDLER_MAX ?
yep, MAX is probably a more representative name
>
> > +/* NULL terminated list of shutdown handles */
> > +static crash_shutdown_t crash_shutdown_handles[CRASH_SHUTDOWN_HANDLES_NU=
> M+1];
> > +static DEFINE_SPINLOCK(crash_handles_lock);
> > +
> > #ifdef CONFIG_SMP
> > static atomic_t enter_on_soft_reset =3D ATOMIC_INIT(0);
> > =20
> > @@ -285,9 +292,69 @@ static inline void crash_kexec_stop_spus
> > }
> > #endif /* CONFIG_SPU_BASE */
> > =20
> > +/*=20
> > + * Register a function to be called on shutdown. Only use this if you
> > + * can't reset your device in the second kernel.
> > + */
> > +int crash_shutdown_register(crash_shutdown_t handler)
> > +{
> > + unsigned int i, rc;
> > +
> > + spin_lock(&crash_handles_lock);
>
> > + for(i =3D 0 ; i <=3D CRASH_SHUTDOWN_HANDLES_NUM; i++) {
> > + if (!crash_shutdown_handles[i]) {
> > + /* Insert handle at end */
> > + crash_shutdown_handles[i] =3D handler;
> > + rc =3D 0;
> > + break;
> > + }
> > + }
> >=20
> > + if (i =3D=3D CRASH_SHUTDOWN_HANDLES_NUM){
> > + printk(KERN_ERR "Crash shutdown handles full, "
> > + "not registered.\n");
> > + rc =3D 1;
> > + }
> > +
> > + spin_unlock(&crash_handles_lock);
>
> Perhaps?
Yep, looks nicer. I'll fix the one below too.
>
> > + return rc;
> > +}
> > +EXPORT_SYMBOL(crash_shutdown_register);
> > +
> > +int crash_shutdown_unregister(crash_shutdown_t handler)
> > +{
> > + unsigned int i;
> > +
> > + spin_lock(&crash_handles_lock);
> > + for(i =3D 0 ; i <=3D CRASH_SHUTDOWN_HANDLES_NUM; i++)
> > + if (crash_shutdown_handles[i] =3D=3D handler)
> > + break;
> > +
> > + if (i =3D=3D CRASH_SHUTDOWN_HANDLES_NUM){
> > + printk(KERN_ERR "Crash shutdown handle not found\n");
> > + spin_unlock(&crash_handles_lock);
> > + return 1;
> > + }
> > +
> > + /* Shift handles down */
> > + while(crash_shutdown_handles[i]) {
> > + crash_shutdown_handles[i] =3D crash_shutdown_handles[i+1];
> > + i++;
> > + }
> > + spin_unlock(&crash_handles_lock);
> > + return 0;
> > +}
> > +EXPORT_SYMBOL(crash_shutdown_unregister);
> > +
> > +static long crash_shutdown_buf[SETJMP_BUF_LEN];
>
> unsigned long?
yep
>
> > +
> > +static int handle_fault(struct pt_regs *regs)
> > +{
> > + longjmp(crash_shutdown_buf, 1);
> > + return 0;
> > +}
> > +
> > void default_machine_crash_shutdown(struct pt_regs *regs)
> > {
> > - unsigned int irq;
> > + unsigned int i;
> > =20
> > /*
> > * This function is only called after the system
> > @@ -301,14 +368,27 @@ void default_machine_crash_shutdown(stru
> > */
> > hard_irq_disable();
> > =20
> > - for_each_irq(irq) {
> > - struct irq_desc *desc =3D irq_desc + irq;
> > + for_each_irq(i) {
> > + struct irq_desc *desc =3D irq_desc + i;
> > =20
> > if (desc->status & IRQ_INPROGRESS)
> > - desc->chip->eoi(irq);
> > + desc->chip->eoi(i);
> > =20
> > if (!(desc->status & IRQ_DISABLED))
> > - desc->chip->disable(irq);
> > + desc->chip->disable(i);
> > + }
> > +
> > + /* Call registered shutdown routines */
> > + __debugger_fault_handler =3D handle_fault;
> > + i =3D 0;
> > + while(crash_shutdown_handles[i]){
> > + if (setjmp(crash_shutdown_buf) =3D=3D 0) {
> > + asm volatile("sync; isync");
> > + crash_shutdown_handles[i]();
> > + asm volatile("sync; isync");
> > + __delay(200);
> > + }
> > + i++;
> > }
>
> You should probably reset __debugger_fault_handler, just to be safe.
Agreed.
Mikey
^ permalink raw reply
* Re: [PATCH 6/8] mpc83xx: timer driver for PM wakeup
From: Stephen Rothwell @ 2007-12-13 0:14 UTC (permalink / raw)
To: Scott Wood; +Cc: linuxppc-dev, paulus
In-Reply-To: <20071212173604.GE5596@loki.buserror.net>
[-- Attachment #1: Type: text/plain, Size: 487 bytes --]
Hi Scott,
On Wed, 12 Dec 2007 11:36:04 -0600 Scott Wood <scottwood@freescale.com> wrote:
>
> +static int __devinit gtm_probe(struct of_device *dev,
> + const struct of_device_id *match)
> +{
.
.
.
> +out:
Just for consistency, you probably want
dev_set_drvdata(&dev->dev, NULL);
here
> + kfree(priv);
> + return ret;
> +}
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
http://www.canb.auug.org.au/~sfr/
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply
* [PATCH 1/3] ps3: vuart: fix error path locking
From: Daniel Walker @ 2007-12-12 8:00 UTC (permalink / raw)
To: akpm
Cc: matthias.kaehlcke, linux-kernel, linux, linuxppc-dev, mingo,
kjwinchester
This stray down would cause a permanent sleep which doesn't seem correct.
The other uses of this semaphore appear fairly mutex like it's even initialized
with init_MUTEX() .. So here a patch for removing this one down().
Signed-off-by: Daniel Walker <dwalker@mvista.com>
---
drivers/ps3/ps3-vuart.c | 1 -
1 file changed, 1 deletion(-)
Index: linux-2.6.23/drivers/ps3/ps3-vuart.c
===================================================================
--- linux-2.6.23.orig/drivers/ps3/ps3-vuart.c
+++ linux-2.6.23/drivers/ps3/ps3-vuart.c
@@ -1072,7 +1072,6 @@ static int ps3_vuart_probe(struct ps3_sy
if (result) {
dev_dbg(&dev->core, "%s:%d: drv->probe failed\n",
__func__, __LINE__);
- down(&vuart_bus_priv.probe_mutex);
goto fail_probe;
}
--
^ permalink raw reply
* Re: [PATCH 2/2] kdump shutdown hook support
From: Michael Neuling @ 2007-12-13 0:53 UTC (permalink / raw)
To: Olof Johansson; +Cc: linuxppc-dev, RAISCH, Paul Mackerras, THEMANN
In-Reply-To: <20071212070150.GC786@lixom.net>
>
> > + if (setjmp(crash_shutdown_buf) == 0) {
> > + asm volatile("sync; isync");
> > + crash_shutdown_handles[i]();
> > + asm volatile("sync; isync");
> > + __delay(200);
>
> This looks a bit random. Why the handcoded barriers, and why the delay?
> I don't see a need for the barriers at all here?
I was following the bouncing ball here from the xmon code. We don't
want the hardware executing any of potentially dangerous hooks before
we've setup the setjmp save buffer. Similar, any code past the
dangerous hooks shouldn't be executed before we take a machine check.
It's definitely not a fast path so.... :-)
> At least comment why the delay is needed (and why just 200 is
> sufficient).
xmon.c says:
/* wait a little while to see if we get a machine check */
I'll update the "200" with a #define SETJMP_MACHINE_CHECK_DELAY and push
the same change into the xmon code. This delay in the machine check is
apparently required on 601 machines.
All you other comments I agree with.
Mikey
^ permalink raw reply
* Re: [PATCH 2/3] mpc82xx: Embedded Planet EP8248E support
From: Stephen Rothwell @ 2007-12-13 0:55 UTC (permalink / raw)
To: Scott Wood; +Cc: linuxppc-dev
In-Reply-To: <47606538.2090605@freescale.com>
[-- Attachment #1: Type: text/plain, Size: 713 bytes --]
On Wed, 12 Dec 2007 16:48:24 -0600 Scott Wood <scottwood@freescale.com> wrote:
>
> Stephen Rothwell wrote:
> >> + ep8248e_bcsr = of_iomap(ep8248e_bcsr_node, 0);
> >
> > of_node_put(ep8248e_bcsr_node;
>
> No, because we hold on to the node for later use in ep8248e_mdio_probe().
Sorry, you are right, I didn't notice that it was global ...
> BTW, is there any actual node removal done that justifies dealing with
> refcounts everywhere?
In the hotplug code. So I guess it is not very relevant to you, but it
is a pain to retrofit this stuff if it does become important more widely.
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
http://www.canb.auug.org.au/~sfr/
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply
* Re: [PATCH/RFC] CPM1: implement GPIO API
From: Anton Vorontsov @ 2007-12-13 0:53 UTC (permalink / raw)
To: Arnd Bergmann; +Cc: linuxppc-dev
In-Reply-To: <200712122316.34354.arnd@arndb.de>
On Wed, Dec 12, 2007 at 11:16:33PM +0100, Arnd Bergmann wrote:
> On Wednesday 12 December 2007, Jochen Friedrich wrote:
>
> > +static spinlock_t *cpm1_port_locks;
> > +static int cpm1_num_ports;
>
> Having an array of spinlocks is rather unusual and normally not necessary.
> Did you measure a significant performance impact by using a global lock
> for all ports?
> If not, I would recommend simplifying this.
I disagree. Why should we force bank A to stomp on bank B, if we can
prevent this in few lines of trivial code? It doesn't need any measuring
or simplifying IMO, what's so complexing in array of spinlocks guarding
array of banks?
But, you can repeat that you really want to get rid of this array --
and I'll silently remove it. Not because I gave up, but mostly because
with gpiolib we'll able to embed spinlock into per-bank gpio_chip
structure, thus eventually they will come back. :-))
> > +EXPORT_SYMBOL_GPL(gpio_request);
> > +EXPORT_SYMBOL_GPL(gpio_direction_input);
> > +EXPORT_SYMBOL_GPL(gpio_direction_output);
> > +EXPORT_SYMBOL_GPL(gpio_get_value);
> > +EXPORT_SYMBOL_GPL(gpio_set_value);
>
> All these function names are rather generic identifiers, but you export them
> from a platform specific file. I'd say they should either have a more specific
> name space (e.g. cpm1_gpio_request), or should be implemented in a more
> generic way.
No. This is how gpio api is working currently. With gpiolib[1], most of
these functions will be controller-specific. IIRC, gpiolib is still in
early development stage, so, for now, we have to limit us to one gpio
chip controller.
This works great for us: CPM, CPM2 and QE shouldn't appear on the single
crystal.
I'm not sure if gpiolib will hit 2.6.25, really. Maybe not. So I'd rather
stick with limited gpio api, and later convert it to gpiolib -- it will be
really trivial. Just rename functions and wrap them around gpio_chip
structure.
The bright side of smooth transition is that API itself isn't changing,
GPIO API/GPIOLIB API is fully interchangeable, their differences are
in implementation details.
[1] http://www.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.24-rc4/2.6.24-rc4-mm1/broken-out/generic-gpio-gpio_chip-support.patch
Thanks,
--
Anton Vorontsov
email: cbou@mail.ru
backup email: ya-cbou@yandex.ru
irc://irc.freenode.net/bd2
^ permalink raw reply
* Re: [PATCH 1/3] ps3: vuart: fix error path locking
From: Geoff Levand @ 2007-12-13 2:00 UTC (permalink / raw)
To: akpm
Cc: Daniel Walker, matthias.kaehlcke, linux-kernel, linux,
linuxppc-dev, mingo, kjwinchester
In-Reply-To: <20071213003028.676998182@mvista.com>
> This stray down would cause a permanent sleep which doesn't seem correct.
> The other uses of this semaphore appear fairly mutex like it's even initialized
> with init_MUTEX() .. So here a patch for removing this one down().
>
> Signed-off-by: Daniel Walker <dwalker@mvista.com>
>
> ---
> drivers/ps3/ps3-vuart.c | 1 -
> 1 file changed, 1 deletion(-)
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Looks, good.
Andrew, Please apply.
-Geoff
^ permalink raw reply
* RE: initrd - console
From: Siva Prasad @ 2007-12-13 2:06 UTC (permalink / raw)
To: michael; +Cc: linuxppc-dev, linuxppc-embedded
In-Reply-To: <1197336860.7378.29.camel@concordia>
Thanks for the response Michael.
Yes!... I do have /dev/console
I also have the following line in /etc/inittab (::respawn:/sbin/getty -L
ttyS0 115200 VT100)
Still it does not print any thing from the user land. All the kernel
printk's are working fine.
I tried to print the arguments and environment variables for getty and
echo /dev/console. Below is the info.
sys_execve - filename=3D/sbin/getty.
copy_strings: kaddr =3D /sbin/getty.
copy_strings: kaddr =3D USER=3Droot.
copy_strings: kaddr =3D SHELL=3D/bin/sh.
copy_strings: kaddr =3D PATH=3D/usr/bin:/bin:/usr/sbin:/sbin.
copy_strings: kaddr =3D TERM=3Dvt102.
copy_strings: kaddr =3D HOME=3D/.
copy_strings: kaddr =3D VT100.
copy_strings: kaddr =3D 115200.
copy_strings: kaddr =3D ttyS0.
copy_strings: kaddr =3D -L.
copy_strings: kaddr =3D /sbin/getty.
sys_execve - filename=3D/bin/echo.
copy_strings: kaddr =3D /bin/echo.
copy_strings: kaddr =3D GATEWAY0=3D172.27.255.254.
copy_strings: kaddr =3D NETMASK0=3D255.255.0.0.
copy_strings: kaddr =3D PWD=3D/.
copy_strings: kaddr =3D SMBD_ARGS=3D.
copy_strings: kaddr =3D NAMESERVER0=3D172.27.0.1.
copy_strings: kaddr =3D NTP_SERVER=3D.
copy_strings: kaddr =3D SHELL=3D/bin/sh.
copy_strings: kaddr =3D INETD_ARGS=3D.
copy_strings: kaddr =3D BOA_ARGS=3D.
copy_strings: kaddr =3D NMBD_ARGS=3D.
copy_strings: kaddr =3D TMPFS=3Dtmpfs.
copy_strings: kaddr =3D PATH=3D/usr/bin:/bin:/usr/sbin:/sbin.
copy_strings: kaddr =3D READONLY_FS=3D.
copy_strings: kaddr =3D TERM=3Dvt102.
copy_strings: kaddr =3D MODLIST=3D.
copy_strings: kaddr =3D SYSCFG_IFACE0=3Dy.
copy_strings: kaddr =3D IPADDR0=3D172.27.180.41.
copy_strings: kaddr =3D DEPLOYMENT_STYLE=3DRAMDISK.
copy_strings: kaddr =3D SYSCFG_DHCPC_CMD=3Dudhcpc -b -i .
copy_strings: kaddr =3D DHCP_ARG=3D.
copy_strings: kaddr =3D RAMDIRS=3D.
copy_strings: kaddr =3D BROADCAST0=3D172.27.255.255.
copy_strings: kaddr =3D HOME=3D/.
copy_strings: kaddr =3D HOSTNAME=3Dmpc8641hpcn.
copy_strings: kaddr =3D USER=3Droot.
copy_strings: kaddr =3D INTERFACE0=3Deth0.
copy_strings: kaddr =3D /dev/console.
copy_strings: kaddr =3D echo.
Thanks
Siva
-----Original Message-----
From: Michael Ellerman [mailto:michael@ellerman.id.au]=20
Sent: Monday, December 10, 2007 5:34 PM
To: Siva Prasad
Cc: linuxppc-dev@ozlabs.org; linuxppc-embedded@ozlabs.org
Subject: Re: initrd - console
On Mon, 2007-12-10 at 17:26 -0800, Siva Prasad wrote:
> Hi,
>=20
> I am trying to boot kernel with initrd. However, it hangs in
> run_init_process("/sbin/init"). I went into the system calls to see
what
> it is doing.=20
>=20
> As part of debugging, I ended up adding a printk statement in
> arch/powerpc/kernel/process.c:sys_execve() routine. Noticed that all
the
> calls are coming here, however nothing is printed on the screen. I
think
> initrd is executing fine (unless one of you says otherwise). See the
> capture below for boot log.
>=20
> Question 1: how come nothing is printed from ramdisk (userland
programs)
> to the serial console, while all the kernel printk's are working
> perfectly?
Do you have a /dev/console etc. in your initrd?
> Question 2: How important is to have interrupts working for just
> printing. I know that interrupts are must to enter input.
Depends on what your console is, but if it's something simple then you
should be able to write to it without taking interrupts.
cheers
--=20
Michael Ellerman
OzLabs, IBM Australia Development Lab
wwweb: http://michael.ellerman.id.au
phone: +61 2 6212 1183 (tie line 70 21183)
We do not inherit the earth from our ancestors,
we borrow it from our children. - S.M.A.R.T Person
^ permalink raw reply
* RE: Xilinx devicetrees
From: Koss, Mike (Mission Systems) @ 2007-12-13 2:40 UTC (permalink / raw)
To: Stephen Neuendorffer, David H. Lynch Jr., Grant Likely,
linuxppc-embedded
In-Reply-To: <20071125235855.95B9999804D@mail138-cpk.bigfish.com>
[-- Attachment #1: Type: text/plain, Size: 7713 bytes --]
Time for my $.02, since I am heavily weighting my future designs on the
use of the device trees. :) (and b/c I don't check my work e-mail from
home ;P)
________________________________
From: Stephen Neuendorffer [mailto:stephen.neuendorffer@xilinx.com]
Sent: Sunday, November 25, 2007 6:59 PM
To: David H. Lynch Jr.; Grant Likely; linuxppc-embedded
Subject: RE: Xilinx devicetrees
DL> I am not expert on this, but at Pico we already store our boot
monitor in the .bit files in BRAM.
DL> But that is not free. It is one of the reasons we do not use
u-boot. Our boot monitor must fit into 16K of BRAM.
DL> Must be able to perform selftests on critical hardware, support
a flash file system, load bit files from flash to the FGA, load and
exectute elf files, allow a small set of user commands,
DL> and handle hosted vs. standalone operation.
DL> And aparently extract the devicetree from a bit file and pass it
to a linux kernel.
SN> Once you can load a bitstream from flash, loading the device tree
from flash
SN> should be practically free. In any event, why do you do this rather
than just run out of the flash (or a ram copy of the flash?)
This is the approach that I am currently taking with our future design.
In our system, we actually have 2 physical systems running Linux inside
the V4 (that's why there are 2 PowerPCs :) ). My current plan would be
to have the device trees stored in FLASH along w/ a single linux image.
Our bootloader on the board would then copy that information from FLASH
to RAM for both systems. This allows us to have two physically different
systems setup with different hardware, but have one linux image with two
different device trees. With a standard linux kernel weighing it at ~
3-5MB (including initramfs) that's a hefty savings in FLASH for us. Plus
it can considerably lower boot time instead of having to verify multiple
large images.
DL> In static or fairly static hardware, that's fine. Even in somewhat
dynamic hardware with large quantities of startup resources - like a PC.
DL> But in highly dynamic hardware with fairly limited resources it
starts to become an issue.
SN> As Grant says, the dynamic detection doesn't have to be done in the
boot loader, it could be done in the platform code. You can largely
ignore
SN> the device trees, or always boot with a core device tree and figure
it all out later (perhaps using version registers). I anticipate that
SN> the 'standard flow' will have standard platform code for any board
that uses a complete device tree. If you have the need to do something
SN> extraordinary, then you should feel free to hack away... However,
It doesn't seem to me to be really necessary in your case, assuming that
SN> the device tree is packaged (somehow, TBD) along with the bitstream.
I don't know if packaging the device tree with the bitstream is the best
way to go. It's possible that it could lead to headaches for certain
systems that have security restrictions. The same could be said for
using it w/ the SystemACE to load it into RAM after the image. (which is
what I'm currently doing for my 2 linux images in lieu of a true on-chip
bootloader). I am already taking the security concerns into account for
future revisions of the hardware wrt to using a SystemACE, and am
planning on moving the device trees into NV storage like FLASH.
GL> No, unfortunately they don't deal with the problem you're facing
GL> (which I'm facing also). But it will be solved if we figure out a
GL> sane way to bind the device tree up with the FPGA bitstream without
GL> consuming FPGA resources.
DL> Note to Xilinx:
DL> There MUST be some way of binding a device description to a
bit file.
DL> neither building it into the FPGA fabric nor appending it to the
end
DL> of the bit file are perfect solutions,
DL> The former is more powerfull and flexible but wastes precious
DL> resources. The later is more complex and puts more burdens on
DL> software developers, and may be completely unfeasible in some
DL> environments - not mine fortunately.
SN> I don't understand the 'burden on software developers'. The code to
do this will just be standard code. The worst that one can say is:
SN> 1) I need several KB additional non volatile storage. Given the
size of the FPGA bitstream, this can't be a huge constraint.
SN> 2) I can't use compile time optimization based on xparameters as
easily. Anyone want to implement the alternatives mechanism on ppc and
microblaze?
SN> 3) Some additional boot time. However, again, this seems marginal.
I do agree that using more FPGA resources is not a solution to the
problem. I'm already hitting 80% usage on a FX60 and trying to squeeze
more real estate for storage of the device tree seems silly. Especially
since that would require that every image have this extra hardware built
into it just to support booting a Linux kernel. Why should I have to
have different hardware to boot linux, versus non-kernel, xilkernel, or
other (GHS, LynxOS, etc..)?
DL> Regardless, something must be done. An odd collection of
devicetree
DL> files co-mingled with a collection of bit files, is little better
than
DL> xparameter files all over the place.
SN> Certainly.. But in a sense, these are all intermediate files on the
path to the image on the board. That
SN> (and how it is interpreted by the platform code) should be generated
in a consistent fashion by EDK.
SN> See my other email for some of the possibilities. Are there
specific reasons why you think those
SN> proposals are inadequate? Now is the time when we can take
criticism, with the goal towards making
SN> a good end solution.
One solution I've been thinking through (in lieu of direct support from
EDK) is to use a tcl script with xps to traverse the hardware tree and
generate the device tree. It seems like it should be relatively trivial
to obtain the information. It's just going to be a pain to write all the
handlers for each different linux driver: temac, interrupt controller,
DMA controller, etc.
In reality the best way to handle this would be to have EDK generate the
device tree as part of the library/bsp build process. Now, what I'd like
to see with regards to this is the ability to change the handler for the
generating a specific device information. An example could be the temac.
If at some point in the future the temac needs new/more information to
support its configuration/run-time then having to get a patch from
Xilinx for a EDK is way too slow. The developers should be giving the
opportunity to inject a new handler into the various parts of the device
tree generation. That way when the kernel patch is submitted, an EDK
device generator patch will be submitted at the same time to keep
everything in sync.
DL> And once again a plea to ALWAYS make version/capabilities
registers
DL> atleast an optional part of every design.
DL> Embeddeding a device tree into a design might be fairly
expensive. a
DL> pair of read only 32 bit registers is damn near free - basically the
DL> FPGA equivalent of atmost 64 diodes or resistors.
SN> Actually, device trees actually seem to be cheaper (in the whole
system sense) than such registers. Unless there is something I don't
understand?
The issue here is that the hardware changed and the driver doesn't
support it. I think this would be fixed by having information passed to
the driver in the platform_device struct to specify information, since
its not able to be discerned by the physical hardware information:
version registers, etc.
[-- Attachment #2: Type: text/html, Size: 11617 bytes --]
^ permalink raw reply
* Re: [PATCH RFC 0/7] "NAND on UPM" and related patches
From: Chris Fester @ 2007-12-13 3:01 UTC (permalink / raw)
To: avorontsov; +Cc: linuxppc-dev
In-Reply-To: <20071210204705.GA31263@localhost.localdomain>
On Mon, 2007-12-10 at 23:47 +0300, Anton Vorontsov wrote:
> Hi all,
>
> Here are patches to support NAND on UPM. That driver is generic for
> all processors with FSL UPMs. And because of that, few more patches are
> needed -- GPIO API and generic FSL UPM functions.
> I would appreciate any comments and suggestions, thanks!
Hi Anton,
Apologies for not getting back sooner to comment...
We've been using a home-brewed UPM driver for our NAND for a while now.
There's several issues we've hit that I figured I would share. The
issues involve deficiencies of both the UPM and the NAND part itself.
We modeled our driver loosely after the suggestions in this white paper:
http://www.freescale.com/files/32bit/doc/white_paper/NANDFLASHWP.pdf?fpsp=1&WT_TYPE=WhitePapers&WT_VENDOR=FREESCALE&WT_FILE_FORMAT=pdf&WT_ASSET=Documentation
We also connected the NAND according to the suggestions in the above
document.
Something that you should be made aware of right away about the UPM -
you do not have control of the logic lines all of the time. You only
can control them during a transaction (in our case, a byte transaction).
In other words, the time that is between reading/writing bytes, or
putting the address on the bus, or asserting commands you are not able
to hold the lines to a certain state. Most of the control lines coming
from the UPM default to a logic 1 when unused (I believe only one
defaults to a logic 0).
The first issue is timings between versions of processors. We've got
one board using an MPC8349 running a 1Gb ST micro part (NAND01G-B).
Another board is an MPC8347 using the same 1Gb ST micro part. After
much time analyzing logic analyzer captures we found that write pulses
with the 8349 had to be shifted to the left a half clock in order to
properly latch the data on the bus. This was unexpected given the two
boards are very similar and the processors are in the same family. I
suppose the fix was easy enough, we just had to make a new version of
the microcode. What's interesting is that Freescale said that there's
nothing different between the two processors' UPMs. Yet there is a
distinct difference between local bus behavior on the 2 cpus, our LA
captures prove it.
The second issue was with interrupts during reads. We noticed that some
of our boards experienced ECC errors while reading the NAND. Logic
analyzer captures and debugging revealed that when an interrupt happened
while the driver's read code was executing, the UPM went into an idle
state, and the chip select of the part went high. This may not be a
problem for other NAND parts, but for our ST Micro parts, the spec says
that if CS is held high for more than 100us, the part will exit page
read mode. The default state of the UPM pins are high, so when the UPM
is idle all the signals are at logic 1.
Anyways, when the interrupt had completed, or driver wasn't aware that
an interrupt had occurred, so it continued to do it's read loop. The ST
Micro part was now in an undefined state. The page read appeared to
continue just fine, but we almost always had one or more bits corrupted
for the very first resuming data byte.
The fix that we ultimately did was to move the chip select control from
the UPM to a GPIO from the processor. This forced the chip to never
"sleep" during an interrupt, because we could keep the chip select low
for the entire page read transaction. This brought up other minor
issues. You must make sure that your boot loader (U-Boot in our case)
sets the GPIO data BEFORE it sets the GPIO direction. Otherwise the
NAND will automatically enter a start up read condition that will drive
the local bus, causing anything else on the local bus (such as a NOR
flash) to be useless...
The latest version of the app note online (link above) does not mention
the problem you may experience with interrupts. I requested from our
Freescale support contact that Freescale document this fact and make it
available to others such that they won't bump into the same problems we
did!
The THIRD issue we had (actually, are having) is very related to our
second issue. Our customer now wants a 2Gb NAND on our board. We
swapped the chip out. We included one more address byte transaction
that is needed with the larger part in the driver. And it doesn't work.
The part is considered to be the "bigger brother" to the 1Gb part, but
apparently enough of it's state machine has changed that it doesn't
tolerate the AL and CL lines going high while chip select is low.
Incidentally, when debugging our second issue we were told by ST Micro
support that the only time AL and CL were sampled by the NAND was when
W# and R# were driven low. Had we known that the 2Gb part wouldn't have
worked, we would have done much more major reworking to the NAND
subsystem when we respun our board.
This mail isn't meant to be a rant. Everyone knows that this kind of
low-level hardware/software work is difficult. This mail is meant to
caution you against using the NAND with the UPM. Freescale may say that
it works, and present you a pretty looking white paper, but it's really
kludgy and you are pretty guaranteed to have problems. Please encourage
your board designers to hook the NAND to some sort of CPLD device rather
than the UPM. At least with a CPLD you have some real control over the
state of the control lines.
If you for whatever reason are stuck with the UPM...
1.) Get your hardware people to stick inverters on the AL and CL lines.
Adjust your UPM microcode accordingly.
2.) Put your CS under control of a GPIO pin.
3.) Buy a nice logic analyzer, because you're going to need it!!!
I hope this helps someone out there... I've been spending a lot of time
on-and-off on this. Every time we think we have it right one little
seemingly benign change throws the whole thing out the window...
Okie, happy coding,
Chris Fester
^ permalink raw reply
* [PATCH] Convert media-bay.c to use the kthread API
From: Paul Mackerras @ 2007-12-13 3:12 UTC (permalink / raw)
To: linuxppc-dev
We aren't supposed to use kernel_thread directly in drivers any more,
and in fact using kthread_run is a bit simpler.
Signed-off-by: Paul Mackerras <paulus@samba.org>
---
diff --git a/drivers/macintosh/mediabay.c b/drivers/macintosh/mediabay.c
index 48d647a..080844b 100644
--- a/drivers/macintosh/mediabay.c
+++ b/drivers/macintosh/mediabay.c
@@ -20,6 +20,7 @@
#include <linux/stddef.h>
#include <linux/init.h>
#include <linux/ide.h>
+#include <linux/kthread.h>
#include <asm/prom.h>
#include <asm/pgtable.h>
#include <asm/io.h>
@@ -35,7 +36,6 @@
#define MB_DEBUG
-#define MB_IGNORE_SIGNALS
#ifdef MB_DEBUG
#define MBDBG(fmt, arg...) printk(KERN_INFO fmt , ## arg)
@@ -622,12 +622,7 @@ static int media_bay_task(void *x)
{
int i;
- strcpy(current->comm, "media-bay");
-#ifdef MB_IGNORE_SIGNALS
- sigfillset(¤t->blocked);
-#endif
-
- for (;;) {
+ while (!kthread_should_stop()) {
for (i = 0; i < media_bay_count; ++i) {
down(&media_bays[i].lock);
if (!media_bays[i].sleeping)
@@ -636,8 +631,6 @@ static int media_bay_task(void *x)
}
msleep_interruptible(MB_POLL_DELAY);
- if (signal_pending(current))
- return 0;
}
}
@@ -699,7 +692,7 @@ static int __devinit media_bay_attach(struct macio_dev *mdev, const struct of_de
/* Startup kernel thread */
if (i == 0)
- kernel_thread(media_bay_task, NULL, CLONE_KERNEL);
+ kthread_run(media_bay_task, NULL, "media-bay");
return 0;
^ permalink raw reply related
* [PATCH 0/2] Add crashdump shutdown hooks
From: Michael Neuling @ 2007-12-13 3:16 UTC (permalink / raw)
To: Paul Mackerras; +Cc: linuxppc-dev, Michael Neuling, RAISCH, THEMANN
In-Reply-To: <20071212054512.A02B062C153@localhost.localdomain>
The following patches add crashdump shutdown hooks for POWERPC.
Signed-off-by: Michael Neuling <mikey@neuling.org>
---
This is an updated series following comments from the first post.
Adds some documentation, better code flow, fixes 32 bit compiles and
other updates based on feedback
Again these are based on paulus' for 2.6.25 tree.
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox