* Re: [PATCH v4 0/3] OF-platform PATA driver
From: Anton Vorontsov @ 2008-01-16 5:47 UTC (permalink / raw)
To: Olof Johansson; +Cc: linuxppc-dev, Paul Mundt, Jeff Garzik, linux-ide
In-Reply-To: <20080115164022.GA24590@lixom.net>
On Tue, Jan 15, 2008 at 10:40:22AM -0600, Olof Johansson wrote:
> Hi,
>
> I've applied 1/3 and 2/3 together with my electra_ide move to pasemi.git
> for-2.6.25, and will ask Paul to pull that. Kumar said he'd take 3/3.
>
> I also added the const to the match table as spotted by Stephen.
Great news, thank you!
--
Anton Vorontsov
email: cbou@mail.ru
backup email: ya-cbou@yandex.ru
irc://irc.freenode.net/bd2
^ permalink raw reply
* Re: [PATCH 2/2] [POWERPC] 4xx: Add AMCC Haleakala (405EXr) dts
From: Stefan Roese @ 2008-01-16 5:04 UTC (permalink / raw)
To: David Gibson; +Cc: linuxppc-dev
In-Reply-To: <20080116004642.GD4283@localhost.localdomain>
On Wednesday 16 January 2008, David Gibson wrote:
> On Tue, Jan 15, 2008 at 08:09:25AM +0100, Stefan Roese wrote:
> > The patch adds the Haleakala dts. The Haleakala is a stripped down
> > version of the Kilauea (405EX) with only one EMAC and only one PCIe
> > interface.
>
> [snip]
>
> > + IIC0: i2c@ef600400 {
> > + device_type = "i2c";
>
> No device_type here.
Ok.
> > + compatible = "ibm,iic-405exr", "ibm,iic";
> > + reg = <ef600400 14>;
> > + interrupt-parent = <&UIC0>;
> > + interrupts = <2 4>;
> > + };
> > +
> > + IIC1: i2c@ef600500 {
> > + device_type = "i2c";
>
> Or here.
Ok.
> > + compatible = "ibm,iic-405exr", "ibm,iic";
> > + reg = <ef600500 14>;
> > + interrupt-parent = <&UIC0>;
> > + interrupts = <7 4>;
> > + };
> > +
> > +
> > + RGMII0: emac-rgmii@ef600b00 {
> > + device_type = "rgmii-interface";
>
> And especially not here.
Ok.
Your comments are valid for some of the other 4xx dts files too. Should I
create a patch that removes these device-types there too?
> > + compatible = "ibm,rgmii-405exr", "ibm,rgmii";
> > + reg = <ef600b00 104>;
> > + has-mdio;
> > + };
>
> [snip]
>
> > + PCIE0: pciex@0a0000000 {
> > + device_type = "pci";
> > + #interrupt-cells = <1>;
> > + #size-cells = <2>;
> > + #address-cells = <3>;
> > + compatible = "ibm,plb-pciex-405exr", "ibm,plb-pciex";
> > + primary;
> > + port = <0>; /* port number */
> > + reg = <a0000000 20000000 /* Config space access */
> > + ef000000 00001000>; /* Registers */
> > + dcr-reg = <040 020>;
> > + sdr-base = <400>;
>
> Oh, for crying out loud. They put dcrs on the bridge as well as MMIO
> registers. *facepalm*
Yep. PCIe on 4xx has DCR, SDR *and* MMIO registers.
Best regards,
Stefan
^ permalink raw reply
* Re: [PATCH] [POWERPC] Add of_find_matching_node() helper function
From: Stephen Rothwell @ 2008-01-16 4:49 UTC (permalink / raw)
To: Paul Mackerras; +Cc: linuxppc-dev
In-Reply-To: <18317.19252.530009.495865@cargo.ozlabs.ibm.com>
[-- Attachment #1: Type: text/plain, Size: 317 bytes --]
On Wed, 16 Jan 2008 11:09:24 +1100 Paul Mackerras <paulus@samba.org> wrote:
>
> Grant Likely writes:
>
> > Any comments/concerns on this patch?
>
> I'm about to throw it into my tree.
Fine by me.
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
http://www.canb.auug.org.au/~sfr/
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply
* Re: [PATCH 2/3] mtd: Factor out OF partition support from the NOR driver.
From: Stephen Rothwell @ 2008-01-16 4:41 UTC (permalink / raw)
To: Scott Wood; +Cc: linuxppc-dev, dwmw2, linux-mtd
In-Reply-To: <478D450A.8060802@freescale.com>
[-- Attachment #1: Type: text/plain, Size: 507 bytes --]
On Tue, 15 Jan 2008 17:43:06 -0600 Scott Wood <scottwood@freescale.com> wrote:
>
> Stephen Rothwell wrote:
> >> + nr_parts = 0;
> >> + for (pp = node->child; pp; pp = pp->sibling)
> >
> > for_each_child_of_node(node, pp)
>
> "for_each_child_of_node" is only in Paul's tree, but this has to go via mtd.
>
> Plus, I'm just moving the code; it's not new.
OK, we can change it later.
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
http://www.canb.auug.org.au/~sfr/
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply
* Re: [PATCH 2/2] mpc82xx: Embedded Planet EP8248E support
From: Stephen Rothwell @ 2008-01-16 4:40 UTC (permalink / raw)
To: Scott Wood; +Cc: linuxppc-dev
In-Reply-To: <20080115233047.GB21002@loki.buserror.net>
[-- Attachment #1: Type: text/plain, Size: 469 bytes --]
Hi Scott,
On Tue, 15 Jan 2008 17:30:47 -0600 Scott Wood <scottwood@freescale.com> wrote:
>
> +++ b/arch/powerpc/platforms/82xx/ep8248e.c
> +static __initdata const struct cpm_pin ep8248e_pins[] = {
Again, const doesn't mix with __initdata so just use __initdata.
> +static __initdata const struct of_device_id of_bus_ids[] = {
Here as well.
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
http://www.canb.auug.org.au/~sfr/
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply
* Re: [PATCH 1/2] 8xx: Analogue & Micro Adder875 board support.
From: Stephen Rothwell @ 2008-01-16 4:35 UTC (permalink / raw)
To: Scott Wood; +Cc: linuxppc-dev
In-Reply-To: <20080115233045.GA21002@loki.buserror.net>
[-- Attachment #1: Type: text/plain, Size: 544 bytes --]
Hi Scott,
On Tue, 15 Jan 2008 17:30:45 -0600 Scott Wood <scottwood@freescale.com> wrote:
>
> +++ b/arch/powerpc/platforms/8xx/adder875.c
> +static __initdata const struct cpm_pin adder875_pins[] = {
Sorry, but you can't have both const and __inittdata. The section
attributes that each use conflict. So just make it __initdata.
> +static __initdata const struct of_device_id __initdata of_bus_ids[] = {
Same here.
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
http://www.canb.auug.org.au/~sfr/
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply
* Re: [PATCH 3/8] pseries: phyp dump: reserve-release proof-of-concept
From: Paul Mackerras @ 2008-01-16 4:21 UTC (permalink / raw)
To: Manish Ahuja; +Cc: mahuja, linuxppc-dev, linasvepstas, lkessler, strosake
In-Reply-To: <4782C2FB.7020105@austin.ibm.com>
Manish Ahuja writes:
> Initial patch for reserving memory in early boot, and freeing it later.
> If the previous boot had ended with a crash, the reserved memory would contain
> a copy of the crashed kernel data.
The main problem I see here is that if this option is turned on, the
kernel now has only 256MB of memory from early boot until
subsys_initcalls are done -- on any machine, and whether or not there
is actually a dump. That means, for instance, that a machine running
bare-metal (such as a G5) might not be able to allocate the hash table
for the MMU. Also, any allocations made during that time won't be
able to be node-local.
So it will be necessary to read the flattened device tree early on to
see whether or not there is a dump, so that we don't reserve most of
memory in the cases where there isn't a dump.
Paul.
^ permalink raw reply
* RE: [PATCH 1/3] drivers/misc :UCC based TDM driver for MPC83xx platforms.
From: Aggrwal Poonam @ 2008-01-16 4:20 UTC (permalink / raw)
To: Andrew Morton
Cc: kumar.gala, Phillips Kim, Barkowski Michael, netdev, linux-kernel,
rubini, linuxppc-dev, Kalra Ashish, Cutler Richard
In-Reply-To: <20080114131441.878979d2.akpm@linux-foundation.org>
Thanks Morton for your comments,
I shall incorporate them and reesnd the patch.
With Regards
Poonam=20
=20
=20
-----Original Message-----
From: Andrew Morton [mailto:akpm@linux-foundation.org]=20
Sent: Tuesday, January 15, 2008 2:45 AM
To: Aggrwal Poonam
Cc: rubini@vision.unipv.it; linux-kernel@vger.kernel.org;
linuxppc-dev@ozlabs.org; netdev@vger.kernel.org;
kumar.gala@freescale.co; Barkowski Michael; Phillips Kim; Kalra Ashish;
Cutler Richard
Subject: Re: [PATCH 1/3] drivers/misc :UCC based TDM driver for MPC83xx
platforms.
On Mon, 10 Dec 2007 17:34:44 +0530 (IST)
Poonam_Aggrwal-b10812 <b10812@freescale.com> wrote:
> From: Poonam Aggrwal <b10812@freescale.com>
>=20
> The UCC TDM driver basically multiplexes and demultiplexes data from=20
> different channels. It can interface with for example SLIC kind of=20
> devices to receive TDM data demultiplex it and send to upper=20
> applications. At the transmit end it receives data for different=20
> channels multiplexes it and sends them on the TDM channel. It=20
> internally uses TSA( Time Slot Assigner) which does multiplexing and=20
> demultiplexing, UCC to perform SDMA between host buffers and the TSA,
CMX to connect TSA to UCC.
>=20
> This driver will run on MPC8323E-RDB platforms.
>=20
> ...
>
> +#define PREV_PHASE(x) ((x =3D=3D 0) ? MAX_PHASE : (x - 1)) #define=20
> +NEXT_PHASE(x) (((x + 1) > MAX_PHASE) ? 0 : (x + 1))
These macros can reference their arg more than once and are hence
dangerous. What does PREV_PHASE(foo++) do to foo?
And, in general: do not implement in cpp that which could have been
implemented in C.
> +static struct ucc_tdm_info utdm_primary_info =3D {
> + .uf_info =3D {
> + .tsa =3D 1,
> + .cdp =3D 1,
> + .cds =3D 1,
> + .ctsp =3D 1,
> + .ctss =3D 1,
> + .revd =3D 1,
> + .urfs =3D 0x128,
> + .utfs =3D 0x128,
> + .utfet =3D 0,
> + .utftt =3D 0x128,
> + .ufpt =3D 256,
> + .ttx_trx =3D
UCC_FAST_GUMR_TRANSPARENT_TTX_TRX_TRANSPARENT,
> + .tenc =3D UCC_FAST_TX_ENCODING_NRZ,
> + .renc =3D UCC_FAST_RX_ENCODING_NRZ,
> + .tcrc =3D UCC_FAST_16_BIT_CRC,
> + .synl =3D UCC_FAST_SYNC_LEN_NOT_USED,
> + },
> + .ucc_busy =3D 0,
> +};
> +
> +static struct ucc_tdm_info utdm_info[8];
> +
> +static void dump_siram(struct tdm_ctrl *tdm_c) { #if defined(DEBUG)
Microscopic note: kernel code tends to do
#ifdef FOO
if only one identifier is being tested and
#if defined(FOO) && defined(BAR)
if more than one is being tested.
There is no rational reason for this ;)
> + int i;
> + u16 phy_num_ts;
> +
> + phy_num_ts =3D tdm_c->physical_num_ts;
> +
> + pr_debug("SI TxRAM dump\n");
> + /* each slot entry in SI RAM is of 2 bytes */
> + for (i =3D 0; i < phy_num_ts * 2; i++)
> + pr_debug("%x ", in_8(&qe_immr->sir.tx[i]));
> + pr_debug("\nSI RxRAM dump\n");
> + for (i =3D 0; i < phy_num_ts * 2; i++)
> + pr_debug("%x ", in_8(&qe_immr->sir.rx[i]));
> + pr_debug("\n");
> +#endif
> +}
> +
> +/*
> + * converts u-law compressed samples to linear PCM
> + * If the CONFIG_TDM_LINEAR_PCM flag is not set the
> + * TDM driver receives u-law compressed data from the
> + * SLIC device. This function converts the compressed
> + * data to linear PCM and sends it to upper layers.
> + */
> +static inline int ulaw2int(unsigned char log) {
> + u32 sign, segment, temp, quant;
> + int val;
> +
> + temp =3D log ^ 0xFF;
> + sign =3D (temp & 0x80) >> 7;
> + segment =3D (temp & 0x70) >> 4;
> + quant =3D temp & 0x0F;
> + quant <<=3D 1;
> + quant +=3D 33;
> + quant <<=3D segment;
> + if (sign)
> + val =3D 33 - quant;
> + else
> + val =3D quant - 33;
> +
> + val *=3D 4;
> + return val;
> +}
> +
> +/*
> + * converts linear PCM samples to u-law compressed format.
> + * If the CONFIG_TDM_LINEAR_PCM flag is not set the
> + * TDM driver calls this function to convert the PCM samples
> + * to u-law compressed format before sending them to SLIC
> + * device.
> + */
> +static inline u8 int2ulaw(short linear) {
> + u8 quant, ret;
> + u16 output, absol, temp;
> + u32 i, sign;
> + char segment;
> +
> + ret =3D 0;
> + if (linear >=3D 0)
> + linear =3D (linear >> 2);
> + else
> + linear =3D (0xc000 | (linear >> 2));
> +
> + absol =3D abs(linear) + 33;
> + temp =3D absol;
> + sign =3D (linear >=3D 0) ? 1 : 0;
> + for (i =3D 0; i < 16; i++) {
> + output =3D temp & 0x8000;
> + if (output)
> + break;
> + temp <<=3D 1;
> + }
> + segment =3D 11 - i;
> + quant =3D (absol >> segment) & 0x0F;
> + segment--;
> + segment <<=3D 4;
> + output =3D segment + quant;
> + if (absol > 8191)
> + output =3D 0x7F;
> + if (sign)
> + ret ^=3D 0xFF;
> + else
> + ret ^=3D 0x7F;
> + return ret;
> +}
hrm, how many copies of ulaw/alaw conversion functions do we need in the
tree before someone writes a library function for it?
> + out_be16(&rx_bd->status, bd_status);
> + out_be32(&rx_bd->buf,
> + tdm_c->dma_input_addr + i * SAMPLE_DEPTH * act_num_ts);
> +
> + bd_status =3D (u16) ((T_R | T_CM | T_W) >> 16);
> + bd_len =3D SAMPLE_DEPTH * act_num_ts;
> + out_be16(&tx_bd->length, bd_len);
> + out_be16(&tx_bd->status, bd_status);
> + out_be32(&tx_bd->buf,
> + tdm_c->dma_output_addr + i * SAMPLE_DEPTH *
act_num_ts);
> +
> + config_si(tdm_c);
> +
> + setbits32(&qe_immr->ic.qimr, (0x80000000 >> ucc));
The compiler treats 0xNNN constants as unsigned so this works OK. I'd
have put a UL on the end of the constant to be sure ;)
> +static int tdm_start(struct tdm_ctrl *tdm_c) {
> + if (request_irq(tdm_c->ut_info->uf_info.irq, tdm_isr,
> + 0, "tdm", tdm_c)) {
> + printk(KERN_ERR "%s: request_irq for tdm_isr failed\n",
> + __FUNCTION__);
> + return -ENODEV;
> + }
> +
> + ucc_fast_enable(tdm_c->uf_private, COMM_DIR_RX | COMM_DIR_TX);
> +
> +#if !defined(CONFIG_TDM_LINEAR_PCM)
> + pr_info("%s 8-bit u-law compressed mode active\n",
__FUNCTION__);=20
> +#else
> + pr_info("%s 16-bit linear pcm mode active with"
> + " slots 0 & 2\n", __FUNCTION__);
> +#endif
Is this the sort of thing which should be controlled at compile-time?
I'd have thought that a runtime control would be more appropriate (a
sysfs knob or a module parameter). Or just work it out automagically?
> + dump_siram(tdm_c);
> + dump_ucc(tdm_c);
> +
> + setbits8(&(qe_immr->si1.siglmr1_h), (0x1 << tdm_c->tdm_port));
> + pr_info("%s UCC based TDM enabled\n", __FUNCTION__);
> +
> + return 0;
> +}
>
> ...
>
> +static void tdm_read(u32 driver_handle, short chn_id, short
*pcm_buffer,
> + short
len)
> +{
> + int i;
> + u32 phase_rx;
> + /* point to where to start for the current phase data processing
*/
> + u32 temp_rx;
> +
> + struct tdm_ctrl *tdm_c =3D (struct tdm_ctrl *)(driver_handle);
eek. What are we doing here, casting a 32-bit quantity to a kernel
pointer?
a) Seems to rule out ever using this driver on a 64-bit system
b) It's generally suspicious and indicates that some rethinking is
needed.
> +#if !defined(CONFIG_TDM_LINEAR_PCM)
> + u8 *input_tdm_buffer =3D tdm_c->tdm_input_data;
> +
> +#else
> + u16 *input_tdm_buffer =3D
> + (u16 *)tdm_c->tdm_input_data;
> +
> +#endif
> + phase_rx =3D tdm_c->phase_rx;
> + phase_rx =3D PREV_PHASE(phase_rx);
> +
> + temp_rx =3D phase_rx * SAMPLE_DEPTH * EFF_ACTIVE_CH;
> +
> +#if defined(UCC_CACHE_SNOOPING_DISABLED)
> + flush_dcache_range((size_t) &input_tdm_buffer[temp_rx],
> + (size_t) &input_tdm_buffer[temp_rx +
> + SAMPLE_DEPTH *
ACTIVE_CH]);
> +#endif
Again, is it appropriate that this behaviour be determined at
compile-time?
This is very user- and packager- and distributor-unfriendly.
> + for (i =3D 0; i < len; i++) {
> +#if !defined(CONFIG_TDM_LINEAR_PCM)
> + pcm_buffer[i] =3D
> + ulaw2int(input_tdm_buffer[i * EFF_ACTIVE_CH +
> + temp_rx + chn_id]);
> +#else
> + pcm_buffer[i] =3D
> + input_tdm_buffer[i * EFF_ACTIVE_CH + temp_rx +
chn_id]; #endif
> +
> + }
> +
> +}
> +
> +static int ucc_tdm_probe(struct of_device *ofdev,
> + const struct of_device_id *match) {
> + struct device_node *np =3D ofdev->node;
> + struct resource res;
> + const unsigned int *prop;
> + u32 ucc_num, device_num, err, ret =3D 0;
> + struct device_node *np_tmp =3D NULL;
> + dma_addr_t physaddr;
> + void *tdm_buff;
> + struct ucc_tdm_info *ut_info;
> +
> + prop =3D of_get_property(np, "device-id", NULL);
> + ucc_num =3D *prop - 1;
> + if ((ucc_num < 0) || (ucc_num > 7))
> + return -ENODEV;
> +
> + ut_info =3D &utdm_info[ucc_num];
> + if (ut_info =3D=3D NULL) {
> + printk(KERN_ERR "additional data missing\n");
> + return -ENODEV;
> + }
> + if (ut_info->ucc_busy) {
> + printk(KERN_ERR "UCC in use by another TDM driver
instance\n");
> + return -EBUSY;
> + }
> +
> + ut_info->ucc_busy =3D 1;
> + tdm_ctrl[num_tdm_devices++] =3D
> + kzalloc(sizeof(struct tdm_ctrl), GFP_KERNEL);
Shouldn't this check for (num_tdm_devices > MAX_NUM_TDM_DEVICES))?
> + if (!tdm_ctrl[num_tdm_devices - 1]) {
> + printk(KERN_ERR "%s: no memory to allocate for"
> + " tdm control structure\n", __FUNCTION__);
> + num_tdm_devices--;
> + return -ENOMEM;
> + }
> + device_num =3D num_tdm_devices - 1;
> +
> + tdm_ctrl[device_num]->device =3D &ofdev->dev;
> + tdm_ctrl[device_num]->ut_info =3D ut_info;
> +
> + tdm_ctrl[device_num]->ut_info->uf_info.ucc_num =3D ucc_num;
> +
> + prop =3D of_get_property(np, "fsl,tdm-num", NULL);
> + if (prop =3D=3D NULL) {
> + ret =3D -EINVAL;
> + goto get_property_error;
> + }
>
> ...
>
> +
> +#define SET_RX_SI_RAM(n, val) \
> + out_be16((u16 *)&qe_immr->sir.rx[(n)*2], (u16)(val))
> +
> +#define SET_TX_SI_RAM(n, val) \
> + out_be16((u16 *)&qe_immr->sir.tx[(n)*2], (u16)(val))
I don't think there's anything which requires that these be imlemented
in the preprocessor?
> +struct tdm_cfg {
> + u8 com_pin; /* Common receive and transmit pins
> + * 0 =3D separate pins
> + * 1 =3D common pins
> + */
> +
> + u8 fr_sync_level; /* SLx bit Frame Sync Polarity
> + * 0 =3D L1R/TSYNC active logic "1"
> + * 1 =3D L1R/TSYNC active logic "0"
> + */
> +
> + u8 clk_edge; /* CEx bit Tx Rx Clock Edge
> + * 0 =3D TX data on rising edge of clock
> + * RX data on falling edge
> + * 1 =3D TX data on falling edge of clock
> + * RX data on rising edge
> + */
> +
> + u8 fr_sync_edge; /* FEx bit Frame sync edge
> + * Determine when the sync pulses are
sampled
> + * 0 =3D Falling edge
> + * 1 =3D Rising edge
> + */
> +
> + u8 rx_fr_sync_delay; /* TFSDx/RFSDx bits Frame Sync Delay
> + * 00 =3D no bit delay
> + * 01 =3D 1 bit delay
> + * 10 =3D 2 bit delay
> + * 11 =3D 3 bit delay
> + */
> +
> + u8 tx_fr_sync_delay; /* TFSDx/RFSDx bits Frame Sync Delay
> + * 00 =3D no bit delay
> + * 01 =3D 1 bit delay
> + * 10 =3D 2 bit delay
> + * 11 =3D 3 bit delay
> + */
> +
> + u8 active_num_ts; /* Number of active time slots in TDM
> + * assume same active Rx/Tx time slots
> + */
> +};
Nice commenting.
^ permalink raw reply
* Re: [PATCH] [POWERPC] bootwrapper: Add find_node_by_alias and dt_fixup_mac_address_by_alias
From: Kumar Gala @ 2008-01-16 4:12 UTC (permalink / raw)
To: David Gibson; +Cc: linuxppc-dev
In-Reply-To: <20080116000915.GA4283@localhost.localdomain>
On Jan 15, 2008, at 6:09 PM, David Gibson wrote:
> On Tue, Jan 15, 2008 at 09:35:20AM -0600, Kumar Gala wrote:
>> Add the ability to set the mac address given the alias for the
>> device.
>> Removes the need for having a linux,network-index property.
>>
>> ---
>>
>> in my git tree.
>
> Missing a Signed-off-by. Otherwise looks good.
I'm not putting signed-off-by's on patches posted the list just for
review.. thus they will not get picked up by anyone :)
- k
^ permalink raw reply
* Re: [DTC PATCH] libfdt: Add ft_get_next_node(), ft_get_next_prop(), and ft_getprop_offset().
From: David Gibson @ 2008-01-16 3:49 UTC (permalink / raw)
To: Scott Wood; +Cc: linuxppc-dev, jdl
In-Reply-To: <20080115165230.GB10812@ld0162-tx32.am.freescale.net>
On Tue, Jan 15, 2008 at 10:52:30AM -0600, Scott Wood wrote:
> On Tue, Jan 15, 2008 at 11:16:57AM +1100, David Gibson wrote:
> > On Mon, Jan 14, 2008 at 10:30:04AM -0600, Scott Wood wrote:
> > > ft_get_next_node() enumerates children of a given node.
> > > ft_get_next_prop() enumerates propreties of a given node.
> > >
> > > ft_getprop_offset() is like ft_getprop(), but takes a property offset rather
> > > than a node offset and property name; it is primarily intended for use
> > > with ft_get_next_prop().
> >
> > Urg... this kind of serves me right for not getting my act together on
> > iterator functions yet. I really don't like this approach much. I'll
> > see if I can come up with something I prefer this afternoon.
>
> OK.
>
> > The biggest thing I dislike is that I've deliberately avoided having
> > any offsets-to-properties exposed to the library user. That's because
> > the whole offsets change when you write the tree problem is worse for
> > properties than nodes (in that likely idiomatic uses will be bitten by
> > changes in property offsets).
>
> We can drop the property iteration for now; I wrote it for an attempt at
> node merging which I postponed.
Heh.. and I spent most of yesterday working on a counter-proposal for
property iteration. Oh well, let's leave this for now and look at the
node iteration first.
> > > + if (depth != 0)
> > > + return -FDT_ERR_BADSTRUCTURE;
> >
> > I think this should be FDT_ERR_TRUNCATED.
>
> I'd expect TRUNCATED when we hit totalsize without an FDT_END, not when
> we hit FDT_END in an inappropriate context.
Well, TRUNCATED is valid for either situation, and fdt_next_tag() also
returns FDT_END if it reaches totalsize.
> > > + return -FDT_ERR_NOTFOUND;
> >
> > In fact, so should this. This function should never actually reach
> > the FDT_END tag.
>
> No, it's valid if you're iterating over all nodes (node -1, depth
> -1).
Uh.. yeah, I guess so.
> > > +#define FDT_ERR_BADDEPTH 8
> > > + /* FDT_ERR_BADDEPTH: Function was passed a negative
> > > + * (or otherwise invalid) depth. */
> >
> > You've added this error code, but you don't actually return it
> > anywhere...
>
> Oops, it must have been from the aforementioned node merging code, and I
> thought it was from fdt_get_next_node when splitting things up.
Ok.
> > This description is incorrect - you've copied the fdt_getprop()
> > description and forgotten to update it.
>
> /me hides in shame
:)
--
David Gibson | I'll have my music baroque, and my code
david AT gibson.dropbear.id.au | minimalist, thank you. NOT _the_ _other_
| _way_ _around_!
http://www.ozlabs.org/~dgibson
^ permalink raw reply
* Re: [PATCH 2/2] [POWERPC] 4xx: Add AMCC Haleakala (405EXr) dts
From: David Gibson @ 2008-01-16 0:46 UTC (permalink / raw)
To: Stefan Roese; +Cc: linuxppc-dev
In-Reply-To: <1200380965-10245-1-git-send-email-sr@denx.de>
On Tue, Jan 15, 2008 at 08:09:25AM +0100, Stefan Roese wrote:
> The patch adds the Haleakala dts. The Haleakala is a stripped down
> version of the Kilauea (405EX) with only one EMAC and only one PCIe
> interface.
[snip]
> + IIC0: i2c@ef600400 {
> + device_type = "i2c";
No device_type here.
> + compatible = "ibm,iic-405exr", "ibm,iic";
> + reg = <ef600400 14>;
> + interrupt-parent = <&UIC0>;
> + interrupts = <2 4>;
> + };
> +
> + IIC1: i2c@ef600500 {
> + device_type = "i2c";
Or here.
> + compatible = "ibm,iic-405exr", "ibm,iic";
> + reg = <ef600500 14>;
> + interrupt-parent = <&UIC0>;
> + interrupts = <7 4>;
> + };
> +
> +
> + RGMII0: emac-rgmii@ef600b00 {
> + device_type = "rgmii-interface";
And especially not here.
> + compatible = "ibm,rgmii-405exr", "ibm,rgmii";
> + reg = <ef600b00 104>;
> + has-mdio;
> + };
[snip]
> + PCIE0: pciex@0a0000000 {
> + device_type = "pci";
> + #interrupt-cells = <1>;
> + #size-cells = <2>;
> + #address-cells = <3>;
> + compatible = "ibm,plb-pciex-405exr", "ibm,plb-pciex";
> + primary;
> + port = <0>; /* port number */
> + reg = <a0000000 20000000 /* Config space access */
> + ef000000 00001000>; /* Registers */
> + dcr-reg = <040 020>;
> + sdr-base = <400>;
Oh, for crying out loud. They put dcrs on the bridge as well as MMIO
registers. *facepalm*
--
David Gibson | I'll have my music baroque, and my code
david AT gibson.dropbear.id.au | minimalist, thank you. NOT _the_ _other_
| _way_ _around_!
http://www.ozlabs.org/~dgibson
^ permalink raw reply
* Re: Driver - HDLC 83xx QUICC Engine??
From: Joakim Tjernlund @ 2008-01-16 0:34 UTC (permalink / raw)
To: rmcguire; +Cc: linuxppc-embedded
In-Reply-To: <000301c857d7$0195f890$6405a8c0@absolut>
> -----Ursprungligt meddelande-----
> Fr=E5n: Russell McGuire [mailto:rmcguire@videopresence.com]
> Skickat: den 16 januari 2008 01:31
> Till: 'Joakim Tjernlund'
> Kopia: linuxppc-embedded@ozlabs.org
> =C4mne: RE: Driver - HDLC 83xx QUICC Engine??
>=20
> Jocke,
>=20
> I'll let you know if I find any. For a starting point, I have an QE =
ATM
> driver, that is more than likely similar in design <though no Ethernet
> interface>, as it supports the QE engine, and just turns the UCC into =
ATM
> mode, as opposed to HDLC mode. Would imagine the buffering, IO, =
interrupts
> are similar. I am still in process of porting it up from the 82xx CPU.
>=20
> Although HDLC how it registers itself into the kernel is a mystery to =
me, I
> am having trouble finding any HDLC drivers to model this after. Know =
of any
> specs? API? Etc...
Sorry but I don't know. Luckily for me I don't have too either.
Jocke
^ permalink raw reply
* SV: Driver - HDLC 83xx QUICC Engine??
From: Joakim Tjernlund @ 2008-01-16 0:18 UTC (permalink / raw)
To: rmcguire, linuxppc-embedded
In-Reply-To: <000301c857b0$09f01a10$6405a8c0@absolut>
> -----Ursprungligt meddelande-----
> Fr=E5n: =
linuxppc-embedded-bounces+joakim.tjernlund=3Dlumentis.se@ozlabs.org =
[mailto:linuxppc-embedded-
> bounces+joakim.tjernlund=3Dlumentis.se@ozlabs.org] F=F6r Russell =
McGuire
> Skickat: den 15 januari 2008 20:52
> Till: linuxppc-embedded@ozlabs.org
> =C4mne: Driver - HDLC 83xx QUICC Engine??
>=20
> All,
>=20
> Does anyone know of a project or existing driver for supporting HDLC =
for the
>=20
> MPC83xx or MPC82XX Freescale CPUs?
>=20
> Looking to run raw HDLC over various Ethernet or T1 links.
>=20
> -Russ
Me too. Perhaps not, I will be looking at presenting a Ethernet i/f to =
the kernel but
sending out HDLC frames containing the Ethernet packet. If you find/have =
anything
that helps me do that, send it my way please.
Jocke
^ permalink raw reply
* RE: Driver - HDLC 83xx QUICC Engine??
From: Russell McGuire @ 2008-01-16 0:30 UTC (permalink / raw)
To: 'Joakim Tjernlund'; +Cc: linuxppc-embedded
In-Reply-To: <000001c857d5$6154b110$23fe1330$@tjernlund@transmode.se>
Jocke,
I'll let you know if I find any. For a starting point, I have an QE ATM
driver, that is more than likely similar in design <though no Ethernet
interface>, as it supports the QE engine, and just turns the UCC into =
ATM
mode, as opposed to HDLC mode. Would imagine the buffering, IO, =
interrupts
are similar. I am still in process of porting it up from the 82xx CPU.=20
Although HDLC how it registers itself into the kernel is a mystery to =
me, I
am having trouble finding any HDLC drivers to model this after. Know of =
any
specs? API? Etc...
-Russ
> -----Original Message-----
> From: Joakim Tjernlund [mailto:joakim.tjernlund@transmode.se]
> Sent: Tuesday, January 15, 2008 4:19 PM
> To: rmcguire@videopresence.com; linuxppc-embedded@ozlabs.org
> Subject: SV: Driver - HDLC 83xx QUICC Engine??
>=20
> > -----Ursprungligt meddelande-----
> > Fr=E5n: =
linuxppc-embedded-bounces+joakim.tjernlund=3Dlumentis.se@ozlabs.org
> [mailto:linuxppc-embedded-
> > bounces+joakim.tjernlund=3Dlumentis.se@ozlabs.org] F=F6r Russell =
McGuire
> > Skickat: den 15 januari 2008 20:52
> > Till: linuxppc-embedded@ozlabs.org
> > =C4mne: Driver - HDLC 83xx QUICC Engine??
> >
> > All,
> >
> > Does anyone know of a project or existing driver for supporting HDLC =
for
> the
> >
> > MPC83xx or MPC82XX Freescale CPUs?
> >
> > Looking to run raw HDLC over various Ethernet or T1 links.
> >
> > -Russ
>=20
> Me too. Perhaps not, I will be looking at presenting a Ethernet i/f to =
the
> kernel but
> sending out HDLC frames containing the Ethernet packet. If you =
find/have
> anything
> that helps me do that, send it my way please.
>=20
> Jocke
^ permalink raw reply
* Re: [PATCH 3/4] powerpc: Katana750i - Add DTS file
From: David Gibson @ 2008-01-16 0:22 UTC (permalink / raw)
To: Mark A. Greer; +Cc: linuxppc-dev
In-Reply-To: <20080115190806.GD26853@mag.az.mvista.com>
On Tue, Jan 15, 2008 at 12:08:06PM -0700, Mark A. Greer wrote:
> On Tue, Jan 15, 2008 at 10:34:06AM +1100, David Gibson wrote:
> > On Mon, Jan 14, 2008 at 03:59:26PM -0700, Mark A. Greer wrote:
> > > From: Mark A. Greer <mgreer@mvista.com>
>
> Hi David. Thanks for the review.
>
> > > Add DTS file for the Emerson Katana 750i & 752i platforms.
> >
> > [snip]
> > > +/dts-v1/;
> > > +
> > > +/ {
> > > + #address-cells = <1>;
> > > + #size-cells = <1>;
> > > + model = "Katana-75xi"; /* Default */
> > > + compatible = "emerson,katana-750i";
> > > + coherency-off;
> >
> > Where is this flag used from?
>
> Its used in the bootwrapper if & when you use the mv64x60 code to setup
> some of the windows to the I/O ctlrs. This port does use that code
> (because firmware doesn't do it properly) so I need the flag.
Hrm.. ok. I'm just wondering if a new flag is really the right
approach for this, or whether you should be basing the setup off the
compatible property, either for the board or for the main bridge.
> > > + mv64x60@f8100000 { /* Marvell Discovery */
> > > + #address-cells = <1>;
> > > + #size-cells = <1>;
> > > + model = "mv64360"; /* Default */
> > > + compatible = "marvell,mv64360";
> > > + clock-frequency = <133333333>;
> > > + hs_reg_valid;
> > > + reg = <0xf8100000 0x00010000>;
> > > + virtual-reg = <0xf8100000>;
> >
> > You seem to have virtual-reg properties on a *lot* of nodes, are they
> > really necessary?
>
> Actually, not all of them for this board. I copied them from prpmc2800
> which does need all the ones that are there. I'l remove the ones that
> aren't used.
Ok, good.
> > virtual-reg should be used *only* for things which
> > you need to access very early in the bootwrapper. Usually that's only
> > the serial port for the console. Come to that, the CPU is a 750 which
> > has a real mode, so it seems dubious that you would need any
> > virtual-reg values at all.
>
> Well, this came from a discussion about a year ago when we agreed that
> this is how it should be done. Just because MSR[IR,DR] can be cleared
> doesn't mean that they are cleared when the firmware jumps to the
> bootwraper (for all possible firmwares that are out there).
>
> To be able to eliminate virtual-reg, we'd have to add "mmu_off" code to
> the bootwrapper which isn't hard but its already in the kernel (for
> 32-bit anyway). So why duplicate?
Ok, that's a good enough reason for me.
> I'm not that attached to virtual-reg. In fact, I'd be happy to get rid
> of it but only if we can be sure it doesn't cause more mess down the
> road.
>
> > [snip]
> > > + flash@e8000000 {
> > > + #address-cells = <1>;
> > > + #size-cells = <1>;
> > > + compatible = "cfi-flash";
> > > + bank-width = <4>;
> > > + device-width = <2>;
> > > + reg = <0xe8000000 0x04000000>;
> > > + monitor@0 {
> > > + label = "Monitor";
> >
> > If you're using the "label" property, it would be normal to name the
> > nodes simply "partition@address".
>
> I'm using the partition names that were used in the equivalent code
> under arch/ppc. I'm trying to keep things looking the same as they used
> to as much as possible. Besides, I don't see any others doing it that
> way.
My point is that the partition code uses either "label" (if present)
or the node name for the partition name. If label properties are
present, the node name is redundant information, so it seems more
sensible to leave something generic there.
[snip]
> > > + CUNIT: cunit@f200 {
> >
> > What is this device? It needs some sort of "compatible" value.
>
> Does it? Its a separate block of regs but its only used in the mpsc
> node--its never looked up on its own by kernel code. Do all nodes need
> "compatible" even when it'll never be used? (Just want to know.)
Hrm.. if it's really just extra mpsc registers, should it be a
seperate device, or just another range in the mpsc's "reg" property?
[snip]
> > > + mpp@f000 {
> > > + compatible = "marvell,mv64360-mpp";
> > > + reg = <0xf000 0x10>;
> > > + };
> > > +
> > > + gpp@f100 {
> > > + compatible = "marvell,mv64360-gpp";
> > > + reg = <0xf100 0x20>;
> > > + };
> >
> > What are these two devices?
>
> mpp == multi-purpose pins
> gpp == general purpose pins
>
> They're really 2 separate reg blocks and are used for any number of
> things including incoming PCI interrupts. I'm not accessing them
> currently so I can eliminate them in this dts.
Hrm. The device tree should generally describe the hardware, even if
Linux doesn't use it yet. Are these basically some sort of GPIO
interface? If so you should look at the new GPIO binding which has
been proposed.
[snip]
> > > + chosen {
> > > + bootargs = "ip=on";
> >
> > The dts file should not include a "bootargs" value. The wrapper will
> > fill that in from the kernel config.
>
> Actually, the kernel .config CONFIG_CMDLINE is only used by the kernel
> when nothing is passed in from the bootwrapper. The bootwrapper gets
> the cmdline from either bootargs or from the __builtin_cmdline section.
>
> I prefer to not rely on CONFIG_CMDLINE because it doesn't afford the
> user a chance to edit or add to the cmdline when booting. You can always
> type in the whole thing at the "Linux/PowerPC load: " prompt but I'd rather
> see what is going to be used and then edit it if I want to. With
> CONFIG_CMDLINE, it just gets used if nothing was passed in from the
> bootwrapper.
>
> That raises an issue that I've for time time (I've tried to get rid of
> __builtin_cmdline before but was unsuccessful).
>
> We currently have 3 possible sources for a default cmdline--seems like
> at least one too many.
Yes :(. I've looked at this before, though obviously I never got to
figuring out what to do about it.
> IMHO we need a way to change the default cmdline in the field so
> sysadmins can change it per board and not have to type it in every time
> they boot. /chosen/bootargs and __builtin_cmdline can both do that.
> We don't need both, though. And, since bootargs is specified by OF
> and documented in booting-without-of.txt, can we finally get rid of
> __builtin_cmdline? I'd sure like to.
>
> We can probably get rid of CONFIG_CMDLINE too since everyone uses DTs
> now and they can have a /chosen/bootargs. Anyone have a reason to keep
> CONFIG_CMDLINE around?
>
> Would you mind elaborating on why you are opposed to /chosen/bootargs?
Just because it's nasty for people to have to go in and change the dts
just to change their default command line - which they might well want
to do for things as simple as setting a default root device.
--
David Gibson | I'll have my music baroque, and my code
david AT gibson.dropbear.id.au | minimalist, thank you. NOT _the_ _other_
| _way_ _around_!
http://www.ozlabs.org/~dgibson
^ permalink raw reply
* Re: [PATCH] [POWERPC] Add of_find_matching_node() helper function
From: Paul Mackerras @ 2008-01-16 0:09 UTC (permalink / raw)
To: Grant Likely; +Cc: linuxppc-dev, Stephen Rothwell
In-Reply-To: <fa686aa40801150709s31a1fc6eg751ecdc209a113d6@mail.gmail.com>
Grant Likely writes:
> Any comments/concerns on this patch?
I'm about to throw it into my tree.
Paul.
^ permalink raw reply
* Re: [PATCH] [POWERPC] bootwrapper: Add find_node_by_alias and dt_fixup_mac_address_by_alias
From: David Gibson @ 2008-01-16 0:09 UTC (permalink / raw)
To: Kumar Gala; +Cc: linuxppc-dev
In-Reply-To: <Pine.LNX.4.64.0801150934390.29314@blarg.am.freescale.net>
On Tue, Jan 15, 2008 at 09:35:20AM -0600, Kumar Gala wrote:
> Add the ability to set the mac address given the alias for the device.
> Removes the need for having a linux,network-index property.
>
> ---
>
> in my git tree.
Missing a Signed-off-by. Otherwise looks good.
--
David Gibson | I'll have my music baroque, and my code
david AT gibson.dropbear.id.au | minimalist, thank you. NOT _the_ _other_
| _way_ _around_!
http://www.ozlabs.org/~dgibson
^ permalink raw reply
* [PATCH 2/2] Freescale enhanced Local Bus Controller FCM NAND support.
From: Scott Wood @ 2008-01-15 23:54 UTC (permalink / raw)
To: dwmw2; +Cc: linuxppc-dev, linux-mtd
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
drivers/mtd/nand/Kconfig | 9 +
drivers/mtd/nand/Makefile | 1 +
drivers/mtd/nand/fsl_elbc_nand.c | 1245 ++++++++++++++++++++++++++++++++++++++
3 files changed, 1255 insertions(+), 0 deletions(-)
create mode 100644 drivers/mtd/nand/fsl_elbc_nand.c
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 0a840d5..4a3c675 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -321,4 +321,13 @@ config MTD_NAND_ORION
No board specific support is done by this driver, each board
must advertise a platform_device for the driver to attach.
+config MTD_NAND_FSL_ELBC
+ tristate "NAND support for Freescale eLBC controllers"
+ depends on MTD_NAND && PPC_OF
+ help
+ Various Freescale chips, including the 8313, include a NAND Flash
+ Controller Module with built-in hardware ECC capabilities.
+ Enabling this option will enable you to use this to control
+ external NAND devices.
+
endif # MTD_NAND
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index e35f5ea..80d575e 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -31,5 +31,6 @@ obj-$(CONFIG_MTD_NAND_PLATFORM) += plat_nand.o
obj-$(CONFIG_MTD_ALAUDA) += alauda.o
obj-$(CONFIG_MTD_NAND_PASEMI) += pasemi_nand.o
obj-$(CONFIG_MTD_NAND_ORION) += orion_nand.o
+obj-$(CONFIG_MTD_NAND_FSL_ELBC) += fsl_elbc_nand.o
nand-objs := nand_base.o nand_bbt.o
diff --git a/drivers/mtd/nand/fsl_elbc_nand.c b/drivers/mtd/nand/fsl_elbc_nand.c
new file mode 100644
index 0000000..5a927a1
--- /dev/null
+++ b/drivers/mtd/nand/fsl_elbc_nand.c
@@ -0,0 +1,1245 @@
+/* Freescale Enhanced Local Bus Controller NAND driver
+ *
+ * Copyright (c) 2006-2007 Freescale Semiconductor
+ *
+ * Authors: Nick Spence <nick.spence@freescale.com>,
+ * Scott Wood <scottwood@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/ioport.h>
+#include <linux/of_platform.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/nand_ecc.h>
+#include <linux/mtd/partitions.h>
+
+#include <asm/io.h>
+
+
+#define MAX_BANKS 8
+#define ERR_BYTE 0xFF /* Value returned for read bytes when read failed */
+#define FCM_TIMEOUT_MSECS 500 /* Maximum number of mSecs to wait for FCM */
+
+struct elbc_bank {
+ __be32 br; /**< Base Register */
+#define BR_BA 0xFFFF8000
+#define BR_BA_SHIFT 15
+#define BR_PS 0x00001800
+#define BR_PS_SHIFT 11
+#define BR_PS_8 0x00000800 /* Port Size 8 bit */
+#define BR_PS_16 0x00001000 /* Port Size 16 bit */
+#define BR_PS_32 0x00001800 /* Port Size 32 bit */
+#define BR_DECC 0x00000600
+#define BR_DECC_SHIFT 9
+#define BR_DECC_OFF 0x00000000 /* HW ECC checking and generation off */
+#define BR_DECC_CHK 0x00000200 /* HW ECC checking on, generation off */
+#define BR_DECC_CHK_GEN 0x00000400 /* HW ECC checking and generation on */
+#define BR_WP 0x00000100
+#define BR_WP_SHIFT 8
+#define BR_MSEL 0x000000E0
+#define BR_MSEL_SHIFT 5
+#define BR_MS_GPCM 0x00000000 /* GPCM */
+#define BR_MS_FCM 0x00000020 /* FCM */
+#define BR_MS_SDRAM 0x00000060 /* SDRAM */
+#define BR_MS_UPMA 0x00000080 /* UPMA */
+#define BR_MS_UPMB 0x000000A0 /* UPMB */
+#define BR_MS_UPMC 0x000000C0 /* UPMC */
+#define BR_V 0x00000001
+#define BR_V_SHIFT 0
+#define BR_RES ~(BR_BA|BR_PS|BR_DECC|BR_WP|BR_MSEL|BR_V)
+
+ __be32 or; /**< Base Register */
+#define OR0 0x5004
+#define OR1 0x500C
+#define OR2 0x5014
+#define OR3 0x501C
+#define OR4 0x5024
+#define OR5 0x502C
+#define OR6 0x5034
+#define OR7 0x503C
+
+#define OR_FCM_AM 0xFFFF8000
+#define OR_FCM_AM_SHIFT 15
+#define OR_FCM_BCTLD 0x00001000
+#define OR_FCM_BCTLD_SHIFT 12
+#define OR_FCM_PGS 0x00000400
+#define OR_FCM_PGS_SHIFT 10
+#define OR_FCM_CSCT 0x00000200
+#define OR_FCM_CSCT_SHIFT 9
+#define OR_FCM_CST 0x00000100
+#define OR_FCM_CST_SHIFT 8
+#define OR_FCM_CHT 0x00000080
+#define OR_FCM_CHT_SHIFT 7
+#define OR_FCM_SCY 0x00000070
+#define OR_FCM_SCY_SHIFT 4
+#define OR_FCM_SCY_1 0x00000010
+#define OR_FCM_SCY_2 0x00000020
+#define OR_FCM_SCY_3 0x00000030
+#define OR_FCM_SCY_4 0x00000040
+#define OR_FCM_SCY_5 0x00000050
+#define OR_FCM_SCY_6 0x00000060
+#define OR_FCM_SCY_7 0x00000070
+#define OR_FCM_RST 0x00000008
+#define OR_FCM_RST_SHIFT 3
+#define OR_FCM_TRLX 0x00000004
+#define OR_FCM_TRLX_SHIFT 2
+#define OR_FCM_EHTR 0x00000002
+#define OR_FCM_EHTR_SHIFT 1
+};
+
+struct elbc_regs {
+ struct elbc_bank bank[8];
+ u8 res0[0x28];
+ __be32 mar; /**< UPM Address Register */
+ u8 res1[0x4];
+ __be32 mamr; /**< UPMA Mode Register */
+ __be32 mbmr; /**< UPMB Mode Register */
+ __be32 mcmr; /**< UPMC Mode Register */
+ u8 res2[0x8];
+ __be32 mrtpr; /**< Memory Refresh Timer Prescaler Register */
+ __be32 mdr; /**< UPM Data Register */
+ u8 res3[0x4];
+ __be32 lsor; /**< Special Operation Initiation Register */
+ __be32 lsdmr; /**< SDRAM Mode Register */
+ u8 res4[0x8];
+ __be32 lurt; /**< UPM Refresh Timer */
+ __be32 lsrt; /**< SDRAM Refresh Timer */
+ u8 res5[0x8];
+ __be32 ltesr; /**< Transfer Error Status Register */
+#define LTESR_BM 0x80000000
+#define LTESR_FCT 0x40000000
+#define LTESR_PAR 0x20000000
+#define LTESR_WP 0x04000000
+#define LTESR_ATMW 0x00800000
+#define LTESR_ATMR 0x00400000
+#define LTESR_CS 0x00080000
+#define LTESR_CC 0x00000001
+#define LTESR_NAND_MASK (LTESR_FCT | LTESR_PAR | LTESR_CC)
+ __be32 ltedr; /**< Transfer Error Disable Register */
+ __be32 lteir; /**< Transfer Error Interrupt Register */
+ __be32 lteatr; /**< Transfer Error Attributes Register */
+ __be32 ltear; /**< Transfer Error Address Register */
+ u8 res6[0xC];
+ __be32 lbcr; /**< Configuration Register */
+#define LBCR_LDIS 0x80000000
+#define LBCR_LDIS_SHIFT 31
+#define LBCR_BCTLC 0x00C00000
+#define LBCR_BCTLC_SHIFT 22
+#define LBCR_AHD 0x00200000
+#define LBCR_LPBSE 0x00020000
+#define LBCR_LPBSE_SHIFT 17
+#define LBCR_EPAR 0x00010000
+#define LBCR_EPAR_SHIFT 16
+#define LBCR_BMT 0x0000FF00
+#define LBCR_BMT_SHIFT 8
+#define LBCR_INIT 0x00040000
+ __be32 lcrr; /**< Clock Ratio Register */
+#define LCRR_DBYP 0x80000000
+#define LCRR_DBYP_SHIFT 31
+#define LCRR_BUFCMDC 0x30000000
+#define LCRR_BUFCMDC_SHIFT 28
+#define LCRR_ECL 0x03000000
+#define LCRR_ECL_SHIFT 24
+#define LCRR_EADC 0x00030000
+#define LCRR_EADC_SHIFT 16
+#define LCRR_CLKDIV 0x0000000F
+#define LCRR_CLKDIV_SHIFT 0
+ u8 res7[0x8];
+ __be32 fmr; /**< Flash Mode Register */
+#define FMR_CWTO 0x0000F000
+#define FMR_CWTO_SHIFT 12
+#define FMR_BOOT 0x00000800
+#define FMR_ECCM 0x00000100
+#define FMR_AL 0x00000030
+#define FMR_AL_SHIFT 4
+#define FMR_OP 0x00000003
+#define FMR_OP_SHIFT 0
+ __be32 fir; /**< Flash Instruction Register */
+#define FIR_OP0 0xF0000000
+#define FIR_OP0_SHIFT 28
+#define FIR_OP1 0x0F000000
+#define FIR_OP1_SHIFT 24
+#define FIR_OP2 0x00F00000
+#define FIR_OP2_SHIFT 20
+#define FIR_OP3 0x000F0000
+#define FIR_OP3_SHIFT 16
+#define FIR_OP4 0x0000F000
+#define FIR_OP4_SHIFT 12
+#define FIR_OP5 0x00000F00
+#define FIR_OP5_SHIFT 8
+#define FIR_OP6 0x000000F0
+#define FIR_OP6_SHIFT 4
+#define FIR_OP7 0x0000000F
+#define FIR_OP7_SHIFT 0
+#define FIR_OP_NOP 0x0 /* No operation and end of sequence */
+#define FIR_OP_CA 0x1 /* Issue current column address */
+#define FIR_OP_PA 0x2 /* Issue current block+page address */
+#define FIR_OP_UA 0x3 /* Issue user defined address */
+#define FIR_OP_CM0 0x4 /* Issue command from FCR[CMD0] */
+#define FIR_OP_CM1 0x5 /* Issue command from FCR[CMD1] */
+#define FIR_OP_CM2 0x6 /* Issue command from FCR[CMD2] */
+#define FIR_OP_CM3 0x7 /* Issue command from FCR[CMD3] */
+#define FIR_OP_WB 0x8 /* Write FBCR bytes from FCM buffer */
+#define FIR_OP_WS 0x9 /* Write 1 or 2 bytes from MDR[AS] */
+#define FIR_OP_RB 0xA /* Read FBCR bytes to FCM buffer */
+#define FIR_OP_RS 0xB /* Read 1 or 2 bytes to MDR[AS] */
+#define FIR_OP_CW0 0xC /* Wait then issue FCR[CMD0] */
+#define FIR_OP_CW1 0xD /* Wait then issue FCR[CMD1] */
+#define FIR_OP_RBW 0xE /* Wait then read FBCR bytes */
+#define FIR_OP_RSW 0xE /* Wait then read 1 or 2 bytes */
+ __be32 fcr; /**< Flash Command Register */
+#define FCR_CMD0 0xFF000000
+#define FCR_CMD0_SHIFT 24
+#define FCR_CMD1 0x00FF0000
+#define FCR_CMD1_SHIFT 16
+#define FCR_CMD2 0x0000FF00
+#define FCR_CMD2_SHIFT 8
+#define FCR_CMD3 0x000000FF
+#define FCR_CMD3_SHIFT 0
+ __be32 fbar; /**< Flash Block Address Register */
+#define FBAR_BLK 0x00FFFFFF
+ __be32 fpar; /**< Flash Page Address Register */
+#define FPAR_SP_PI 0x00007C00
+#define FPAR_SP_PI_SHIFT 10
+#define FPAR_SP_MS 0x00000200
+#define FPAR_SP_CI 0x000001FF
+#define FPAR_SP_CI_SHIFT 0
+#define FPAR_LP_PI 0x0003F000
+#define FPAR_LP_PI_SHIFT 12
+#define FPAR_LP_MS 0x00000800
+#define FPAR_LP_CI 0x000007FF
+#define FPAR_LP_CI_SHIFT 0
+ __be32 fbcr; /**< Flash Byte Count Register */
+#define FBCR_BC 0x00000FFF
+ u8 res11[0x8];
+ u8 res8[0xF00];
+};
+
+struct fsl_elbc_ctrl;
+
+/* mtd information per set */
+
+struct fsl_elbc_mtd {
+ struct mtd_info mtd;
+ struct nand_chip chip;
+ struct fsl_elbc_ctrl *ctrl;
+
+ struct device *dev;
+ int bank; /* Chip select bank number */
+ u8 __iomem *vbase; /* Chip select base virtual address */
+ int page_size; /* NAND page size (0=512, 1=2048) */
+ unsigned int fmr; /* FCM Flash Mode Register value */
+};
+
+/* overview of the fsl elbc controller */
+
+struct fsl_elbc_ctrl {
+ struct nand_hw_control controller;
+ struct fsl_elbc_mtd *chips[MAX_BANKS];
+
+ /* device info */
+ struct device *dev;
+ struct elbc_regs __iomem *regs;
+ int irq;
+ wait_queue_head_t irq_wait;
+ unsigned int irq_status; /* status read from LTESR by irq handler */
+ u8 __iomem *addr; /* Address of assigned FCM buffer */
+ unsigned int page; /* Last page written to / read from */
+ unsigned int read_bytes; /* Number of bytes read during command */
+ unsigned int column; /* Saved column from SEQIN */
+ unsigned int index; /* Pointer to next byte to 'read' */
+ unsigned int status; /* status read from LTESR after last op */
+ unsigned int mdr; /* UPM/FCM Data Register value */
+ unsigned int use_mdr; /* Non zero if the MDR is to be set */
+ unsigned int oob; /* Non zero if operating on OOB data */
+ char *oob_poi; /* Place to write ECC after read back */
+};
+
+/* These map to the positions used by the FCM hardware ECC generator */
+
+/* Small Page FLASH with FMR[ECCM] = 0 */
+static struct nand_ecclayout fsl_elbc_oob_sp_eccm0 = {
+ .eccbytes = 3,
+ .eccpos = {6, 7, 8},
+ .oobfree = { {0, 5}, {9, 7} },
+ .oobavail = 12,
+};
+
+/* Small Page FLASH with FMR[ECCM] = 1 */
+static struct nand_ecclayout fsl_elbc_oob_sp_eccm1 = {
+ .eccbytes = 3,
+ .eccpos = {8, 9, 10},
+ .oobfree = { {0, 5}, {6, 2}, {11, 5} },
+ .oobavail = 12,
+};
+
+/* Large Page FLASH with FMR[ECCM] = 0 */
+static struct nand_ecclayout fsl_elbc_oob_lp_eccm0 = {
+ .eccbytes = 12,
+ .eccpos = {6, 7, 8, 22, 23, 24, 38, 39, 40, 54, 55, 56},
+ .oobfree = { {1, 5}, {9, 13}, {25, 13}, {41, 13}, {57, 7} },
+ .oobavail = 48,
+};
+
+/* Large Page FLASH with FMR[ECCM] = 1 */
+static struct nand_ecclayout fsl_elbc_oob_lp_eccm1 = {
+ .eccbytes = 12,
+ .eccpos = {8, 9, 10, 24, 25, 26, 40, 41, 42, 56, 57, 58},
+ .oobfree = { {1, 7}, {11, 13}, {27, 13}, {43, 13}, {59, 5} },
+ .oobavail = 48,
+};
+
+/*=================================*/
+
+/*
+ * Set up the FCM hardware block and page address fields, and the fcm
+ * structure addr field to point to the correct FCM buffer in memory
+ */
+static void set_addr(struct mtd_info *mtd, int column, int page_addr, int oob)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct fsl_elbc_mtd *priv = chip->priv;
+ struct fsl_elbc_ctrl *ctrl = priv->ctrl;
+ struct elbc_regs __iomem *lbc = ctrl->regs;
+ int buf_num;
+
+ ctrl->page = page_addr;
+
+ out_be32(&lbc->fbar,
+ page_addr >> (chip->phys_erase_shift - chip->page_shift));
+
+ if (priv->page_size) {
+ out_be32(&lbc->fpar,
+ ((page_addr << FPAR_LP_PI_SHIFT) & FPAR_LP_PI) |
+ (oob ? FPAR_LP_MS : 0) | column);
+ buf_num = (page_addr & 1) << 2;
+ } else {
+ out_be32(&lbc->fpar,
+ ((page_addr << FPAR_SP_PI_SHIFT) & FPAR_SP_PI) |
+ (oob ? FPAR_SP_MS : 0) | column);
+ buf_num = page_addr & 7;
+ }
+
+ ctrl->addr = priv->vbase + buf_num * 1024;
+ ctrl->index = column;
+
+ /* for OOB data point to the second half of the buffer */
+ if (oob)
+ ctrl->index += priv->page_size ? 2048 : 512;
+
+ dev_vdbg(ctrl->dev, "set_addr: bank=%d, ctrl->addr=0x%p (0x%p), "
+ "index %x, pes %d ps %d\n",
+ buf_num, ctrl->addr, priv->vbase, ctrl->index,
+ chip->phys_erase_shift, chip->page_shift);
+}
+
+/*
+ * execute FCM command and wait for it to complete
+ */
+static int fsl_elbc_run_command(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct fsl_elbc_mtd *priv = chip->priv;
+ struct fsl_elbc_ctrl *ctrl = priv->ctrl;
+ struct elbc_regs __iomem *lbc = ctrl->regs;
+
+ /* Setup the FMR[OP] to execute without write protection */
+ out_be32(&lbc->fmr, priv->fmr | 3);
+ if (ctrl->use_mdr)
+ out_be32(&lbc->mdr, ctrl->mdr);
+
+ dev_vdbg(ctrl->dev,
+ "fsl_elbc_run_command: fmr=%08x fir=%08x fcr=%08x\n",
+ in_be32(&lbc->fmr), in_be32(&lbc->fir), in_be32(&lbc->fcr));
+ dev_vdbg(ctrl->dev,
+ "fsl_elbc_run_command: fbar=%08x fpar=%08x "
+ "fbcr=%08x bank=%d\n",
+ in_be32(&lbc->fbar), in_be32(&lbc->fpar),
+ in_be32(&lbc->fbcr), priv->bank);
+
+ /* execute special operation */
+ out_be32(&lbc->lsor, priv->bank);
+
+ /* wait for FCM complete flag or timeout */
+ ctrl->irq_status = 0;
+ wait_event_timeout(ctrl->irq_wait, ctrl->irq_status,
+ FCM_TIMEOUT_MSECS * HZ/1000);
+ ctrl->status = ctrl->irq_status;
+
+ /* store mdr value in case it was needed */
+ if (ctrl->use_mdr)
+ ctrl->mdr = in_be32(&lbc->mdr);
+
+ ctrl->use_mdr = 0;
+
+ dev_vdbg(ctrl->dev,
+ "fsl_elbc_run_command: stat=%08x mdr=%08x fmr=%08x\n",
+ ctrl->status, ctrl->mdr, in_be32(&lbc->fmr));
+
+ /* returns 0 on success otherwise non-zero) */
+ return ctrl->status == LTESR_CC ? 0 : -EIO;
+}
+
+static void fsl_elbc_do_read(struct nand_chip *chip, int oob)
+{
+ struct fsl_elbc_mtd *priv = chip->priv;
+ struct fsl_elbc_ctrl *ctrl = priv->ctrl;
+ struct elbc_regs __iomem *lbc = ctrl->regs;
+
+ if (priv->page_size) {
+ out_be32(&lbc->fir,
+ (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ (FIR_OP_CA << FIR_OP1_SHIFT) |
+ (FIR_OP_PA << FIR_OP2_SHIFT) |
+ (FIR_OP_CW1 << FIR_OP3_SHIFT) |
+ (FIR_OP_RBW << FIR_OP4_SHIFT));
+
+ out_be32(&lbc->fcr, (NAND_CMD_READ0 << FCR_CMD0_SHIFT) |
+ (NAND_CMD_READSTART << FCR_CMD1_SHIFT));
+ } else {
+ out_be32(&lbc->fir,
+ (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ (FIR_OP_CA << FIR_OP1_SHIFT) |
+ (FIR_OP_PA << FIR_OP2_SHIFT) |
+ (FIR_OP_RBW << FIR_OP3_SHIFT));
+
+ if (oob)
+ out_be32(&lbc->fcr, NAND_CMD_READOOB << FCR_CMD0_SHIFT);
+ else
+ out_be32(&lbc->fcr, NAND_CMD_READ0 << FCR_CMD0_SHIFT);
+ }
+}
+
+/* cmdfunc send commands to the FCM */
+static void fsl_elbc_cmdfunc(struct mtd_info *mtd, unsigned int command,
+ int column, int page_addr)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct fsl_elbc_mtd *priv = chip->priv;
+ struct fsl_elbc_ctrl *ctrl = priv->ctrl;
+ struct elbc_regs __iomem *lbc = ctrl->regs;
+
+ ctrl->use_mdr = 0;
+
+ /* clear the read buffer */
+ ctrl->read_bytes = 0;
+ if (command != NAND_CMD_PAGEPROG)
+ ctrl->index = 0;
+
+ switch (command) {
+ /* READ0 and READ1 read the entire buffer to use hardware ECC. */
+ case NAND_CMD_READ1:
+ column += 256;
+
+ /* fall-through */
+ case NAND_CMD_READ0:
+ dev_dbg(ctrl->dev,
+ "fsl_elbc_cmdfunc: NAND_CMD_READ0, page_addr:"
+ " 0x%x, column: 0x%x.\n", page_addr, column);
+
+
+ out_be32(&lbc->fbcr, 0); /* read entire page to enable ECC */
+ set_addr(mtd, 0, page_addr, 0);
+
+ ctrl->read_bytes = mtd->writesize + mtd->oobsize;
+ ctrl->index += column;
+
+ fsl_elbc_do_read(chip, 0);
+ fsl_elbc_run_command(mtd);
+ return;
+
+ /* READOOB reads only the OOB because no ECC is performed. */
+ case NAND_CMD_READOOB:
+ dev_vdbg(ctrl->dev,
+ "fsl_elbc_cmdfunc: NAND_CMD_READOOB, page_addr:"
+ " 0x%x, column: 0x%x.\n", page_addr, column);
+
+ out_be32(&lbc->fbcr, mtd->oobsize - column);
+ set_addr(mtd, column, page_addr, 1);
+
+ ctrl->read_bytes = mtd->writesize + mtd->oobsize;
+
+ fsl_elbc_do_read(chip, 1);
+ fsl_elbc_run_command(mtd);
+ return;
+
+ /* READID must read all 5 possible bytes while CEB is active */
+ case NAND_CMD_READID:
+ dev_vdbg(ctrl->dev, "fsl_elbc_cmdfunc: NAND_CMD_READID.\n");
+
+ out_be32(&lbc->fir, (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ (FIR_OP_UA << FIR_OP1_SHIFT) |
+ (FIR_OP_RBW << FIR_OP2_SHIFT));
+ out_be32(&lbc->fcr, NAND_CMD_READID << FCR_CMD0_SHIFT);
+ /* 5 bytes for manuf, device and exts */
+ out_be32(&lbc->fbcr, 5);
+ ctrl->read_bytes = 5;
+ ctrl->use_mdr = 1;
+ ctrl->mdr = 0;
+
+ set_addr(mtd, 0, 0, 0);
+ fsl_elbc_run_command(mtd);
+ return;
+
+ /* ERASE1 stores the block and page address */
+ case NAND_CMD_ERASE1:
+ dev_vdbg(ctrl->dev,
+ "fsl_elbc_cmdfunc: NAND_CMD_ERASE1, "
+ "page_addr: 0x%x.\n", page_addr);
+ set_addr(mtd, 0, page_addr, 0);
+ return;
+
+ /* ERASE2 uses the block and page address from ERASE1 */
+ case NAND_CMD_ERASE2:
+ dev_vdbg(ctrl->dev, "fsl_elbc_cmdfunc: NAND_CMD_ERASE2.\n");
+
+ out_be32(&lbc->fir,
+ (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ (FIR_OP_PA << FIR_OP1_SHIFT) |
+ (FIR_OP_CM1 << FIR_OP2_SHIFT));
+
+ out_be32(&lbc->fcr,
+ (NAND_CMD_ERASE1 << FCR_CMD0_SHIFT) |
+ (NAND_CMD_ERASE2 << FCR_CMD1_SHIFT));
+
+ out_be32(&lbc->fbcr, 0);
+ ctrl->read_bytes = 0;
+
+ fsl_elbc_run_command(mtd);
+ return;
+
+ /* SEQIN sets up the addr buffer and all registers except the length */
+ case NAND_CMD_SEQIN: {
+ __be32 fcr;
+ dev_vdbg(ctrl->dev,
+ "fsl_elbc_cmdfunc: NAND_CMD_SEQIN/PAGE_PROG, "
+ "page_addr: 0x%x, column: 0x%x.\n",
+ page_addr, column);
+
+ ctrl->column = column;
+ ctrl->oob = 0;
+
+ fcr = (NAND_CMD_PAGEPROG << FCR_CMD1_SHIFT) |
+ (NAND_CMD_SEQIN << FCR_CMD2_SHIFT);
+
+ if (priv->page_size) {
+ out_be32(&lbc->fir,
+ (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ (FIR_OP_CA << FIR_OP1_SHIFT) |
+ (FIR_OP_PA << FIR_OP2_SHIFT) |
+ (FIR_OP_WB << FIR_OP3_SHIFT) |
+ (FIR_OP_CW1 << FIR_OP4_SHIFT));
+
+ fcr |= NAND_CMD_READ0 << FCR_CMD0_SHIFT;
+ } else {
+ out_be32(&lbc->fir,
+ (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ (FIR_OP_CM2 << FIR_OP1_SHIFT) |
+ (FIR_OP_CA << FIR_OP2_SHIFT) |
+ (FIR_OP_PA << FIR_OP3_SHIFT) |
+ (FIR_OP_WB << FIR_OP4_SHIFT) |
+ (FIR_OP_CW1 << FIR_OP5_SHIFT));
+
+ if (column >= mtd->writesize) {
+ /* OOB area --> READOOB */
+ column -= mtd->writesize;
+ fcr |= NAND_CMD_READOOB << FCR_CMD0_SHIFT;
+ ctrl->oob = 1;
+ } else if (column < 256) {
+ /* First 256 bytes --> READ0 */
+ fcr |= NAND_CMD_READ0 << FCR_CMD0_SHIFT;
+ } else {
+ /* Second 256 bytes --> READ1 */
+ fcr |= NAND_CMD_READ1 << FCR_CMD0_SHIFT;
+ }
+ }
+
+ out_be32(&lbc->fcr, fcr);
+ set_addr(mtd, column, page_addr, ctrl->oob);
+ return;
+ }
+
+ /* PAGEPROG reuses all of the setup from SEQIN and adds the length */
+ case NAND_CMD_PAGEPROG: {
+ int full_page;
+ dev_vdbg(ctrl->dev,
+ "fsl_elbc_cmdfunc: NAND_CMD_PAGEPROG "
+ "writing %d bytes.\n", ctrl->index);
+
+ /* if the write did not start at 0 or is not a full page
+ * then set the exact length, otherwise use a full page
+ * write so the HW generates the ECC.
+ */
+ if (ctrl->oob || ctrl->column != 0 ||
+ ctrl->index != mtd->writesize + mtd->oobsize) {
+ out_be32(&lbc->fbcr, ctrl->index);
+ full_page = 0;
+ } else {
+ out_be32(&lbc->fbcr, 0);
+ full_page = 1;
+ }
+
+ fsl_elbc_run_command(mtd);
+
+ /* Read back the page in order to fill in the ECC for the
+ * caller. Is this really needed?
+ */
+ if (full_page && ctrl->oob_poi) {
+ out_be32(&lbc->fbcr, 3);
+ set_addr(mtd, 6, page_addr, 1);
+
+ ctrl->read_bytes = mtd->writesize + 9;
+
+ fsl_elbc_do_read(chip, 1);
+ fsl_elbc_run_command(mtd);
+
+ memcpy_fromio(ctrl->oob_poi + 6,
+ &ctrl->addr[ctrl->index], 3);
+ ctrl->index += 3;
+ }
+
+ ctrl->oob_poi = NULL;
+ return;
+ }
+
+ /* CMD_STATUS must read the status byte while CEB is active */
+ /* Note - it does not wait for the ready line */
+ case NAND_CMD_STATUS:
+ out_be32(&lbc->fir,
+ (FIR_OP_CM0 << FIR_OP0_SHIFT) |
+ (FIR_OP_RBW << FIR_OP1_SHIFT));
+ out_be32(&lbc->fcr, NAND_CMD_STATUS << FCR_CMD0_SHIFT);
+ out_be32(&lbc->fbcr, 1);
+ set_addr(mtd, 0, 0, 0);
+ ctrl->read_bytes = 1;
+
+ fsl_elbc_run_command(mtd);
+
+ /* The chip always seems to report that it is
+ * write-protected, even when it is not.
+ */
+ setbits8(ctrl->addr, NAND_STATUS_WP);
+ return;
+
+ /* RESET without waiting for the ready line */
+ case NAND_CMD_RESET:
+ dev_dbg(ctrl->dev, "fsl_elbc_cmdfunc: NAND_CMD_RESET.\n");
+ out_be32(&lbc->fir, FIR_OP_CM0 << FIR_OP0_SHIFT);
+ out_be32(&lbc->fcr, NAND_CMD_RESET << FCR_CMD0_SHIFT);
+ fsl_elbc_run_command(mtd);
+ return;
+
+ default:
+ dev_err(ctrl->dev,
+ "fsl_elbc_cmdfunc: error, unsupported command 0x%x.\n",
+ command);
+ }
+}
+
+static void fsl_elbc_select_chip(struct mtd_info *mtd, int chip)
+{
+ /* The hardware does not seem to support multiple
+ * chips per bank.
+ */
+}
+
+/*
+ * Write buf to the FCM Controller Data Buffer
+ */
+static void fsl_elbc_write_buf(struct mtd_info *mtd, const u8 *buf, int len)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct fsl_elbc_mtd *priv = chip->priv;
+ struct fsl_elbc_ctrl *ctrl = priv->ctrl;
+ unsigned int bufsize = mtd->writesize + mtd->oobsize;
+
+ if (len < 0) {
+ dev_err(ctrl->dev, "write_buf of %d bytes", len);
+ ctrl->status = 0;
+ return;
+ }
+
+ if ((unsigned int)len > bufsize - ctrl->index) {
+ dev_err(ctrl->dev,
+ "write_buf beyond end of buffer "
+ "(%d requested, %u available)\n",
+ len, bufsize - ctrl->index);
+ len = bufsize - ctrl->index;
+ }
+
+ memcpy_toio(&ctrl->addr[ctrl->index], buf, len);
+ ctrl->index += len;
+}
+
+/*
+ * read a byte from either the FCM hardware buffer if it has any data left
+ * otherwise issue a command to read a single byte.
+ */
+static u8 fsl_elbc_read_byte(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct fsl_elbc_mtd *priv = chip->priv;
+ struct fsl_elbc_ctrl *ctrl = priv->ctrl;
+
+ /* If there are still bytes in the FCM, then use the next byte. */
+ if (ctrl->index < ctrl->read_bytes)
+ return in_8(&ctrl->addr[ctrl->index++]);
+
+ dev_err(ctrl->dev, "read_byte beyond end of buffer\n");
+ return ERR_BYTE;
+}
+
+/*
+ * Read from the FCM Controller Data Buffer
+ */
+static void fsl_elbc_read_buf(struct mtd_info *mtd, u8 *buf, int len)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct fsl_elbc_mtd *priv = chip->priv;
+ struct fsl_elbc_ctrl *ctrl = priv->ctrl;
+ int avail;
+
+ if (len < 0)
+ return;
+
+ avail = min((unsigned int)len, ctrl->read_bytes - ctrl->index);
+ memcpy_fromio(buf, &ctrl->addr[ctrl->index], avail);
+ ctrl->index += avail;
+
+ if (len > avail)
+ dev_err(ctrl->dev,
+ "read_buf beyond end of buffer "
+ "(%d requested, %d available)\n",
+ len, avail);
+}
+
+/*
+ * Verify buffer against the FCM Controller Data Buffer
+ */
+static int fsl_elbc_verify_buf(struct mtd_info *mtd, const u_char *buf, int len)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct fsl_elbc_mtd *priv = chip->priv;
+ struct fsl_elbc_ctrl *ctrl = priv->ctrl;
+ int i;
+
+ if (len < 0) {
+ dev_err(ctrl->dev, "write_buf of %d bytes", len);
+ return -EINVAL;
+ }
+
+ if ((unsigned int)len > ctrl->read_bytes - ctrl->index) {
+ dev_err(ctrl->dev,
+ "verify_buf beyond end of buffer "
+ "(%d requested, %u available)\n",
+ len, ctrl->read_bytes - ctrl->index);
+
+ ctrl->index = ctrl->read_bytes;
+ return -EINVAL;
+ }
+
+ for (i = 0; i < len; i++)
+ if (in_8(&ctrl->addr[ctrl->index + i]) != buf[i])
+ break;
+
+ ctrl->index += len;
+ return i == len && ctrl->status == LTESR_CC ? 0 : -EIO;
+}
+
+/* This function is called after Program and Erase Operations to
+ * check for success or failure.
+ */
+static int fsl_elbc_wait(struct mtd_info *mtd, struct nand_chip *chip)
+{
+ struct fsl_elbc_mtd *priv = chip->priv;
+ struct fsl_elbc_ctrl *ctrl = priv->ctrl;
+ struct elbc_regs __iomem *lbc = ctrl->regs;
+
+ if (ctrl->status != LTESR_CC)
+ return NAND_STATUS_FAIL;
+
+ /* Use READ_STATUS command, but wait for the device to be ready */
+ ctrl->use_mdr = 0;
+ out_be32(&lbc->fir,
+ (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ (FIR_OP_RBW << FIR_OP1_SHIFT));
+ out_be32(&lbc->fcr, NAND_CMD_STATUS << FCR_CMD0_SHIFT);
+ out_be32(&lbc->fbcr, 1);
+ set_addr(mtd, 0, 0, 0);
+ ctrl->read_bytes = 1;
+
+ fsl_elbc_run_command(mtd);
+
+ if (ctrl->status != LTESR_CC)
+ return NAND_STATUS_FAIL;
+
+ /* The chip always seems to report that it is
+ * write-protected, even when it is not.
+ */
+ setbits8(ctrl->addr, NAND_STATUS_WP);
+ return fsl_elbc_read_byte(mtd);
+}
+
+static int fsl_elbc_chip_init_tail(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct fsl_elbc_mtd *priv = chip->priv;
+ struct fsl_elbc_ctrl *ctrl = priv->ctrl;
+ struct elbc_regs __iomem *lbc = ctrl->regs;
+ unsigned int al;
+
+ /* calculate FMR Address Length field */
+ al = 0;
+ if (chip->pagemask & 0xffff0000)
+ al++;
+ if (chip->pagemask & 0xff000000)
+ al++;
+
+ /* add to ECCM mode set in fsl_elbc_init */
+ priv->fmr |= (12 << FMR_CWTO_SHIFT) | /* Timeout > 12 ms */
+ (al << FMR_AL_SHIFT);
+
+ dev_dbg(ctrl->dev, "fsl_elbc_init: nand->numchips = %d\n",
+ chip->numchips);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: nand->chipsize = %ld\n",
+ chip->chipsize);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: nand->pagemask = %8x\n",
+ chip->pagemask);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: nand->chip_delay = %d\n",
+ chip->chip_delay);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: nand->badblockpos = %d\n",
+ chip->badblockpos);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: nand->chip_shift = %d\n",
+ chip->chip_shift);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: nand->page_shift = %d\n",
+ chip->page_shift);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: nand->phys_erase_shift = %d\n",
+ chip->phys_erase_shift);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: nand->ecclayout = %p\n",
+ chip->ecclayout);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: nand->ecc.mode = %d\n",
+ chip->ecc.mode);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: nand->ecc.steps = %d\n",
+ chip->ecc.steps);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: nand->ecc.bytes = %d\n",
+ chip->ecc.bytes);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: nand->ecc.total = %d\n",
+ chip->ecc.total);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: nand->ecc.layout = %p\n",
+ chip->ecc.layout);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: mtd->flags = %08x\n", mtd->flags);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: mtd->size = %d\n", mtd->size);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: mtd->erasesize = %d\n",
+ mtd->erasesize);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: mtd->writesize = %d\n",
+ mtd->writesize);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: mtd->oobsize = %d\n",
+ mtd->oobsize);
+
+ /* adjust Option Register and ECC to match Flash page size */
+ if (mtd->writesize == 512) {
+ priv->page_size = 0;
+ clrbits32(&lbc->bank[priv->bank].or, ~OR_FCM_PGS);
+ } else if (mtd->writesize == 2048) {
+ priv->page_size = 1;
+ setbits32(&lbc->bank[priv->bank].or, OR_FCM_PGS);
+ /* adjust ecc setup if needed */
+ if ((in_be32(&lbc->bank[priv->bank].br) & BR_DECC) ==
+ BR_DECC_CHK_GEN) {
+ chip->ecc.size = 512;
+ chip->ecc.layout = (priv->fmr & FMR_ECCM) ?
+ &fsl_elbc_oob_lp_eccm1 :
+ &fsl_elbc_oob_lp_eccm0;
+ mtd->ecclayout = chip->ecc.layout;
+ mtd->oobavail = chip->ecc.layout->oobavail;
+ }
+ } else {
+ dev_err(ctrl->dev,
+ "fsl_elbc_init: page size %d is not supported\n",
+ mtd->writesize);
+ return -1;
+ }
+
+ /* The default u-boot configuration on MPC8313ERDB causes errors;
+ * more delay is needed. This should be safe for other boards
+ * as well.
+ */
+ setbits32(&lbc->bank[priv->bank].or, 0x70);
+ return 0;
+}
+
+static int fsl_elbc_read_page(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ uint8_t *buf)
+{
+ fsl_elbc_read_buf(mtd, buf, mtd->writesize);
+ fsl_elbc_read_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ if (fsl_elbc_wait(mtd, chip) & NAND_STATUS_FAIL)
+ mtd->ecc_stats.failed++;
+
+ return 0;
+}
+
+/* ECC will be calculated automatically, and errors will be detected in
+ * waitfunc.
+ */
+static void fsl_elbc_write_page(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ const uint8_t *buf)
+{
+ struct fsl_elbc_mtd *priv = chip->priv;
+ struct fsl_elbc_ctrl *ctrl = priv->ctrl;
+
+ fsl_elbc_write_buf(mtd, buf, mtd->writesize);
+ fsl_elbc_write_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ ctrl->oob_poi = chip->oob_poi;
+}
+
+static int fsl_elbc_chip_init(struct fsl_elbc_mtd *priv)
+{
+ struct fsl_elbc_ctrl *ctrl = priv->ctrl;
+ struct elbc_regs __iomem *lbc = ctrl->regs;
+ struct nand_chip *chip = &priv->chip;
+
+ dev_dbg(priv->dev, "eLBC Set Information for bank %d\n", priv->bank);
+
+ /* Fill in fsl_elbc_mtd structure */
+ priv->mtd.priv = chip;
+ priv->mtd.owner = THIS_MODULE;
+ priv->fmr = 0; /* rest filled in later */
+
+ /* fill in nand_chip structure */
+ /* set up function call table */
+ chip->read_byte = fsl_elbc_read_byte;
+ chip->write_buf = fsl_elbc_write_buf;
+ chip->read_buf = fsl_elbc_read_buf;
+ chip->verify_buf = fsl_elbc_verify_buf;
+ chip->select_chip = fsl_elbc_select_chip;
+ chip->cmdfunc = fsl_elbc_cmdfunc;
+ chip->waitfunc = fsl_elbc_wait;
+
+ /* set up nand options */
+ chip->options = NAND_NO_READRDY | NAND_NO_AUTOINCR;
+
+ chip->controller = &ctrl->controller;
+ chip->priv = priv;
+
+ chip->ecc.read_page = fsl_elbc_read_page;
+ chip->ecc.write_page = fsl_elbc_write_page;
+
+ /* If CS Base Register selects full hardware ECC then use it */
+ if ((in_be32(&lbc->bank[priv->bank].br) & BR_DECC) ==
+ BR_DECC_CHK_GEN) {
+ chip->ecc.mode = NAND_ECC_HW;
+ /* put in small page settings and adjust later if needed */
+ chip->ecc.layout = (priv->fmr & FMR_ECCM) ?
+ &fsl_elbc_oob_sp_eccm1 : &fsl_elbc_oob_sp_eccm0;
+ chip->ecc.size = 512;
+ chip->ecc.bytes = 3;
+ } else {
+ /* otherwise fall back to default software ECC */
+ chip->ecc.mode = NAND_ECC_SOFT;
+ }
+
+ return 0;
+}
+
+static int fsl_elbc_chip_remove(struct fsl_elbc_mtd *priv)
+{
+ struct fsl_elbc_ctrl *ctrl = priv->ctrl;
+
+ nand_release(&priv->mtd);
+
+ if (priv->vbase)
+ iounmap(priv->vbase);
+
+ ctrl->chips[priv->bank] = NULL;
+ kfree(priv);
+
+ return 0;
+}
+
+static int fsl_elbc_chip_probe(struct fsl_elbc_ctrl *ctrl,
+ struct device_node *node)
+{
+ struct elbc_regs __iomem *lbc = ctrl->regs;
+ struct fsl_elbc_mtd *priv;
+ struct resource res;
+#ifdef CONFIG_MTD_PARTITIONS
+ static const char *part_probe_types[]
+ = { "cmdlinepart", "RedBoot", NULL };
+ struct mtd_partition *parts;
+#endif
+ int ret;
+ int bank;
+
+ /* get, allocate and map the memory resource */
+ ret = of_address_to_resource(node, 0, &res);
+ if (ret) {
+ dev_err(ctrl->dev, "failed to get resource\n");
+ return ret;
+ }
+
+ /* find which chip select it is connected to */
+ for (bank = 0; bank < MAX_BANKS; bank++)
+ if ((in_be32(&lbc->bank[bank].br) & BR_V) &&
+ (in_be32(&lbc->bank[bank].br) & BR_MSEL) == BR_MS_FCM &&
+ (in_be32(&lbc->bank[bank].br) &
+ in_be32(&lbc->bank[bank].or) & BR_BA)
+ == res.start)
+ break;
+
+ if (bank >= MAX_BANKS) {
+ dev_err(ctrl->dev, "address did not match any chip selects\n");
+ return -ENODEV;
+ }
+
+ priv = kzalloc(sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ ctrl->chips[bank] = priv;
+ priv->bank = bank;
+ priv->ctrl = ctrl;
+ priv->dev = ctrl->dev;
+
+ priv->vbase = ioremap(res.start, res.end - res.start + 1);
+ if (!priv->vbase) {
+ dev_err(ctrl->dev, "failed to map chip region\n");
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ ret = fsl_elbc_chip_init(priv);
+ if (ret)
+ goto err;
+
+ ret = nand_scan_ident(&priv->mtd, 1);
+ if (ret)
+ goto err;
+
+ ret = fsl_elbc_chip_init_tail(&priv->mtd);
+ if (ret)
+ goto err;
+
+ ret = nand_scan_tail(&priv->mtd);
+ if (ret)
+ goto err;
+
+#ifdef CONFIG_MTD_PARTITIONS
+ /* First look for RedBoot table or partitions on the command
+ * line, these take precedence over device tree information */
+ ret = parse_mtd_partitions(&priv->mtd, part_probe_types, &parts, 0);
+ if (ret < 0)
+ goto err;
+
+#ifdef CONFIG_MTD_OF_PARTS
+ if (ret == 0) {
+ ret = of_mtd_parse_partitions(priv->dev, &priv->mtd,
+ node, &parts);
+ if (ret < 0)
+ goto err;
+ }
+#endif
+
+ if (ret > 0)
+ add_mtd_partitions(&priv->mtd, parts, ret);
+ else
+#endif
+ add_mtd_device(&priv->mtd);
+
+ printk(KERN_INFO "eLBC NAND device at 0x%zx, bank %d\n",
+ res.start, priv->bank);
+ return 0;
+
+err:
+ fsl_elbc_chip_remove(priv);
+ return ret;
+}
+
+static int __devinit fsl_elbc_ctrl_init(struct fsl_elbc_ctrl *ctrl)
+{
+ struct elbc_regs __iomem *lbc = ctrl->regs;
+
+ /* clear event registers */
+ setbits32(&lbc->ltesr, LTESR_NAND_MASK);
+ out_be32(&lbc->lteatr, 0);
+
+ /* Enable interrupts for any detected events */
+ out_be32(&lbc->lteir, LTESR_NAND_MASK);
+
+ ctrl->read_bytes = 0;
+ ctrl->index = 0;
+ ctrl->addr = NULL;
+
+ return 0;
+}
+
+static int __devexit fsl_elbc_ctrl_remove(struct of_device *ofdev)
+{
+ struct fsl_elbc_ctrl *ctrl = dev_get_drvdata(&ofdev->dev);
+ int i;
+
+ for (i = 0; i < MAX_BANKS; i++)
+ if (ctrl->chips[i])
+ fsl_elbc_chip_remove(ctrl->chips[i]);
+
+ if (ctrl->irq)
+ free_irq(ctrl->irq, ctrl);
+
+ if (ctrl->regs)
+ iounmap(ctrl->regs);
+
+ dev_set_drvdata(&ofdev->dev, NULL);
+ kfree(ctrl);
+ return 0;
+}
+
+/* NOTE: This interrupt is also used to report other localbus events,
+ * such as transaction errors on other chipselects. If we want to
+ * capture those, we'll need to move the IRQ code into a shared
+ * LBC driver.
+ */
+
+static irqreturn_t fsl_elbc_ctrl_irq(int irqno, void *data)
+{
+ struct fsl_elbc_ctrl *ctrl = data;
+ struct elbc_regs __iomem *lbc = ctrl->regs;
+ __be32 status = in_be32(&lbc->ltesr) & LTESR_NAND_MASK;
+
+ if (status) {
+ out_be32(&lbc->ltesr, status);
+ out_be32(&lbc->lteatr, 0);
+
+ ctrl->irq_status = status;
+ smp_wmb();
+ wake_up(&ctrl->irq_wait);
+
+ return IRQ_HANDLED;
+ }
+
+ return IRQ_NONE;
+}
+
+/* fsl_elbc_ctrl_probe
+ *
+ * called by device layer when it finds a device matching
+ * one our driver can handled. This code allocates all of
+ * the resources needed for the controller only. The
+ * resources for the NAND banks themselves are allocated
+ * in the chip probe function.
+*/
+
+static int __devinit fsl_elbc_ctrl_probe(struct of_device *ofdev,
+ const struct of_device_id *match)
+{
+ struct device_node *child;
+ struct fsl_elbc_ctrl *ctrl;
+ int ret;
+
+ ctrl = kzalloc(sizeof(*ctrl), GFP_KERNEL);
+ if (!ctrl)
+ return -ENOMEM;
+
+ dev_set_drvdata(&ofdev->dev, ctrl);
+
+ spin_lock_init(&ctrl->controller.lock);
+ init_waitqueue_head(&ctrl->controller.wq);
+ init_waitqueue_head(&ctrl->irq_wait);
+
+ ctrl->regs = of_iomap(ofdev->node, 0);
+ if (!ctrl->regs) {
+ dev_err(&ofdev->dev, "failed to get memory region\n");
+ ret = -ENODEV;
+ goto err;
+ }
+
+ ctrl->irq = of_irq_to_resource(ofdev->node, 0, NULL);
+ if (ctrl->irq == NO_IRQ) {
+ dev_err(&ofdev->dev, "failed to get irq resource\n");
+ ret = -ENODEV;
+ goto err;
+ }
+
+ ctrl->dev = &ofdev->dev;
+
+ ret = fsl_elbc_ctrl_init(ctrl);
+ if (ret < 0)
+ goto err;
+
+ ret = request_irq(ctrl->irq, fsl_elbc_ctrl_irq, 0, "fsl-elbc", ctrl);
+ if (ret != 0) {
+ dev_err(&ofdev->dev, "failed to install irq (%d)\n",
+ ctrl->irq);
+ ret = ctrl->irq;
+ goto err;
+ }
+
+ child = NULL;
+ while ((child = of_get_next_child(ofdev->node, child)))
+ if (of_device_is_compatible(child, "fsl,elbc-fcm-nand"))
+ fsl_elbc_chip_probe(ctrl, child);
+
+ return 0;
+
+err:
+ fsl_elbc_ctrl_remove(ofdev);
+ return ret;
+}
+
+static const struct of_device_id fsl_elbc_match[] = {
+ {
+ .compatible = "fsl,elbc",
+ },
+ {}
+};
+
+static struct of_platform_driver fsl_elbc_ctrl_driver = {
+ .driver = {
+ .name = "fsl-elbc",
+ },
+ .match_table = fsl_elbc_match,
+ .probe = fsl_elbc_ctrl_probe,
+ .remove = __devexit_p(fsl_elbc_ctrl_remove),
+};
+
+static int __init fsl_elbc_init(void)
+{
+ return of_register_platform_driver(&fsl_elbc_ctrl_driver);
+}
+
+static void __exit fsl_elbc_exit(void)
+{
+ of_unregister_platform_driver(&fsl_elbc_ctrl_driver);
+}
+
+module_init(fsl_elbc_init);
+module_exit(fsl_elbc_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Freescale");
+MODULE_DESCRIPTION("Freescale Enhanced Local Bus Controller MTD NAND driver");
--
1.5.3.8
^ permalink raw reply related
* [PATCH 1/2] mtd: Factor out OF partition support from the NOR driver.
From: Scott Wood @ 2008-01-15 23:54 UTC (permalink / raw)
To: dwmw2; +Cc: linuxppc-dev, linux-mtd
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
drivers/mtd/Kconfig | 8 ++++
drivers/mtd/Makefile | 1 +
drivers/mtd/maps/physmap_of.c | 89 ++++++++++++----------------------------
drivers/mtd/ofpart.c | 74 +++++++++++++++++++++++++++++++++
include/linux/mtd/partitions.h | 9 ++++-
5 files changed, 118 insertions(+), 63 deletions(-)
create mode 100644 drivers/mtd/ofpart.c
diff --git a/drivers/mtd/Kconfig b/drivers/mtd/Kconfig
index 661eac0..e850334 100644
--- a/drivers/mtd/Kconfig
+++ b/drivers/mtd/Kconfig
@@ -150,6 +150,14 @@ config MTD_AFS_PARTS
for your particular device. It won't happen automatically. The
'armflash' map driver (CONFIG_MTD_ARMFLASH) does this, for example.
+config MTD_OF_PARTS
+ tristate "Flash partition map based on OF description"
+ depends on PPC_OF && MTD_PARTITIONS
+ help
+ This provides a partition parsing function which derives
+ the partition map from the children of the flash node,
+ as described in Documentation/powerpc/booting-without-of.txt.
+
comment "User Modules And Translation Layers"
config MTD_CHAR
diff --git a/drivers/mtd/Makefile b/drivers/mtd/Makefile
index 7f0b04b..538e33d 100644
--- a/drivers/mtd/Makefile
+++ b/drivers/mtd/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_MTD_CONCAT) += mtdconcat.o
obj-$(CONFIG_MTD_REDBOOT_PARTS) += redboot.o
obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o
obj-$(CONFIG_MTD_AFS_PARTS) += afs.o
+obj-$(CONFIG_MTD_OF_PARTS) += ofpart.o
# 'Users' - code which presents functionality to userspace.
obj-$(CONFIG_MTD_CHAR) += mtdchar.o
diff --git a/drivers/mtd/maps/physmap_of.c b/drivers/mtd/maps/physmap_of.c
index d4bcd3f..49acd41 100644
--- a/drivers/mtd/maps/physmap_of.c
+++ b/drivers/mtd/maps/physmap_of.c
@@ -80,65 +80,6 @@ static int parse_obsolete_partitions(struct of_device *dev,
return nr_parts;
}
-
-static int __devinit parse_partitions(struct of_flash *info,
- struct of_device *dev)
-{
- const char *partname;
- static const char *part_probe_types[]
- = { "cmdlinepart", "RedBoot", NULL };
- struct device_node *dp = dev->node, *pp;
- int nr_parts, i;
-
- /* First look for RedBoot table or partitions on the command
- * line, these take precedence over device tree information */
- nr_parts = parse_mtd_partitions(info->mtd, part_probe_types,
- &info->parts, 0);
- if (nr_parts > 0)
- return nr_parts;
-
- /* First count the subnodes */
- nr_parts = 0;
- for (pp = of_get_next_child(dp, NULL); pp;
- pp = of_get_next_child(dp, pp))
- nr_parts++;
-
- if (nr_parts == 0)
- return parse_obsolete_partitions(dev, info, dp);
-
- info->parts = kzalloc(nr_parts * sizeof(*info->parts),
- GFP_KERNEL);
- if (!info->parts)
- return -ENOMEM;
-
- for (pp = of_get_next_child(dp, NULL), i = 0; pp;
- pp = of_get_next_child(dp, pp), i++) {
- const u32 *reg;
- int len;
-
- reg = of_get_property(pp, "reg", &len);
- if (!reg || (len != 2*sizeof(u32))) {
- of_node_put(pp);
- dev_err(&dev->dev, "Invalid 'reg' on %s\n",
- dp->full_name);
- kfree(info->parts);
- info->parts = NULL;
- return -EINVAL;
- }
- info->parts[i].offset = reg[0];
- info->parts[i].size = reg[1];
-
- partname = of_get_property(pp, "label", &len);
- if (!partname)
- partname = of_get_property(pp, "name", &len);
- info->parts[i].name = (char *)partname;
-
- if (of_get_property(pp, "read-only", &len))
- info->parts[i].mask_flags = MTD_WRITEABLE;
- }
-
- return nr_parts;
-}
#else /* MTD_PARTITIONS */
#define OF_FLASH_PARTS(info) (0)
#define parse_partitions(info, dev) (0)
@@ -213,6 +154,10 @@ static struct mtd_info * __devinit obsolete_probe(struct of_device *dev,
static int __devinit of_flash_probe(struct of_device *dev,
const struct of_device_id *match)
{
+#ifdef CONFIG_MTD_PARTITIONS
+ static const char *part_probe_types[]
+ = { "cmdlinepart", "RedBoot", NULL };
+#endif
struct device_node *dp = dev->node;
struct resource res;
struct of_flash *info;
@@ -275,13 +220,33 @@ static int __devinit of_flash_probe(struct of_device *dev,
}
info->mtd->owner = THIS_MODULE;
- err = parse_partitions(info, dev);
+#ifdef CONFIG_MTD_PARTITIONS
+ /* First look for RedBoot table or partitions on the command
+ * line, these take precedence over device tree information */
+ err = parse_mtd_partitions(info->mtd, part_probe_types,
+ &info->parts, 0);
if (err < 0)
- goto err_out;
+ return err;
+
+#ifdef CONFIG_MTD_OF_PARTS
+ if (err == 0) {
+ err = of_mtd_parse_partitions(&dev->dev, info->mtd,
+ dp, &info->parts);
+ if (err < 0)
+ return err;
+ }
+#endif
+
+ if (err == 0) {
+ err = parse_obsolete_partitions(dev, info, dp);
+ if (err < 0)
+ return err;
+ }
if (err > 0)
- add_mtd_partitions(info->mtd, OF_FLASH_PARTS(info), err);
+ add_mtd_partitions(info->mtd, info->parts, err);
else
+#endif
add_mtd_device(info->mtd);
return 0;
diff --git a/drivers/mtd/ofpart.c b/drivers/mtd/ofpart.c
new file mode 100644
index 0000000..f86e069
--- /dev/null
+++ b/drivers/mtd/ofpart.c
@@ -0,0 +1,74 @@
+/*
+ * Flash partitions described by the OF (or flattened) device tree
+ *
+ * Copyright (C) 2006 MontaVista Software Inc.
+ * Author: Vitaly Wool <vwool@ru.mvista.com>
+ *
+ * Revised to handle newer style flash binding by:
+ * Copyright (C) 2007 David Gibson, IBM Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/of.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+
+int __devinit of_mtd_parse_partitions(struct device *dev,
+ struct mtd_info *mtd,
+ struct device_node *node,
+ struct mtd_partition **pparts)
+{
+ const char *partname;
+ struct device_node *pp;
+ int nr_parts, i;
+
+ /* First count the subnodes */
+ pp = NULL;
+ nr_parts = 0;
+ while ((pp = of_get_next_child(node, pp)))
+ nr_parts++;
+
+ if (nr_parts == 0)
+ return 0;
+
+ *pparts = kzalloc(nr_parts * sizeof(**pparts), GFP_KERNEL);
+ if (!*pparts)
+ return -ENOMEM;
+
+ pp = NULL;
+ i = 0;
+ while ((pp = of_get_next_child(node, pp))) {
+ const u32 *reg;
+ int len;
+
+ reg = of_get_property(pp, "reg", &len);
+ if (!reg || (len != 2 * sizeof(u32))) {
+ of_node_put(pp);
+ dev_err(dev, "Invalid 'reg' on %s\n", node->full_name);
+ kfree(*pparts);
+ *pparts = NULL;
+ return -EINVAL;
+ }
+ (*pparts)[i].offset = reg[0];
+ (*pparts)[i].size = reg[1];
+
+ partname = of_get_property(pp, "label", &len);
+ if (!partname)
+ partname = of_get_property(pp, "name", &len);
+ (*pparts)[i].name = (char *)partname;
+
+ if (of_get_property(pp, "read-only", &len))
+ (*pparts)[i].mask_flags = MTD_WRITEABLE;
+
+ i++;
+ }
+
+ return nr_parts;
+}
+EXPORT_SYMBOL(of_mtd_parse_partitions);
diff --git a/include/linux/mtd/partitions.h b/include/linux/mtd/partitions.h
index da6b3d6..7c37d7e 100644
--- a/include/linux/mtd/partitions.h
+++ b/include/linux/mtd/partitions.h
@@ -71,5 +71,12 @@ extern int parse_mtd_partitions(struct mtd_info *master, const char **types,
#define put_partition_parser(p) do { module_put((p)->owner); } while(0)
-#endif
+struct device;
+struct device_node;
+
+int __devinit of_mtd_parse_partitions(struct device *dev,
+ struct mtd_info *mtd,
+ struct device_node *node,
+ struct mtd_partition **pparts);
+#endif
--
1.5.3.8
^ permalink raw reply related
* Re: [PATCH 2/3] mtd: Factor out OF partition support from the NOR driver.
From: Scott Wood @ 2008-01-15 23:43 UTC (permalink / raw)
To: Stephen Rothwell; +Cc: linuxppc-dev, dwmw2, linux-mtd
In-Reply-To: <20080114172116.a2e5aa18.sfr@canb.auug.org.au>
Stephen Rothwell wrote:
>> + nr_parts = 0;
>> + for (pp = node->child; pp; pp = pp->sibling)
>
> for_each_child_of_node(node, pp)
"for_each_child_of_node" is only in Paul's tree, but this has to go via mtd.
Plus, I'm just moving the code; it's not new.
-Scott
^ permalink raw reply
* [PATCH 2/2] mpc82xx: Embedded Planet EP8248E support
From: Scott Wood @ 2008-01-15 23:30 UTC (permalink / raw)
To: galak; +Cc: linuxppc-dev
This board is also resold by Freescale under the names
"QUICCStart MPC8248 Evaluation System" and "CWH-PPC-8248N-VE".
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
arch/powerpc/boot/Makefile | 3 +-
arch/powerpc/boot/dts/ep8248e.dts | 205 ++++++++
arch/powerpc/boot/ep8248e.c | 55 +++
arch/powerpc/boot/wrapper | 2 +-
arch/powerpc/configs/ep8248e_defconfig | 821 ++++++++++++++++++++++++++++++++
arch/powerpc/platforms/82xx/Kconfig | 13 +
arch/powerpc/platforms/82xx/Makefile | 1 +
arch/powerpc/platforms/82xx/ep8248e.c | 326 +++++++++++++
include/asm-powerpc/mpc8260.h | 1 +
9 files changed, 1425 insertions(+), 2 deletions(-)
create mode 100644 arch/powerpc/boot/dts/ep8248e.dts
create mode 100644 arch/powerpc/boot/ep8248e.c
create mode 100644 arch/powerpc/configs/ep8248e_defconfig
create mode 100644 arch/powerpc/platforms/82xx/ep8248e.c
diff --git a/arch/powerpc/boot/Makefile b/arch/powerpc/boot/Makefile
index 08bf7aa..fcca455 100644
--- a/arch/powerpc/boot/Makefile
+++ b/arch/powerpc/boot/Makefile
@@ -62,7 +62,7 @@ src-plat := of.c cuboot-52xx.c cuboot-83xx.c cuboot-85xx.c holly.c \
ps3-head.S ps3-hvcall.S ps3.c treeboot-bamboo.c cuboot-8xx.c \
cuboot-pq2.c cuboot-sequoia.c treeboot-walnut.c cuboot-bamboo.c \
fixed-head.S ep88xc.c cuboot-hpc2.c ep405.c cuboot-taishan.c \
- cuboot-katmai.c cuboot-rainier.c redboot-8xx.c
+ cuboot-katmai.c cuboot-rainier.c redboot-8xx.c ep8248e.c
src-boot := $(src-wlib) $(src-plat) empty.c
src-boot := $(addprefix $(obj)/, $(src-boot))
@@ -195,6 +195,7 @@ image-$(CONFIG_PPC_8xx) += cuImage.8xx
image-$(CONFIG_PPC_EP88XC) += zImage.ep88xc
image-$(CONFIG_EP405) += zImage.ep405
image-$(CONFIG_8260) += cuImage.pq2
+image-$(CONFIG_EP8248E) += zImage.ep8248e
image-$(CONFIG_PPC_MPC52xx) += cuImage.52xx
image-$(CONFIG_PPC_83xx) += cuImage.83xx
image-$(CONFIG_PPC_85xx) += cuImage.85xx
diff --git a/arch/powerpc/boot/dts/ep8248e.dts b/arch/powerpc/boot/dts/ep8248e.dts
new file mode 100644
index 0000000..9b8b258
--- /dev/null
+++ b/arch/powerpc/boot/dts/ep8248e.dts
@@ -0,0 +1,205 @@
+/*
+ * Device Tree for the Embedded Planet EP8248E board running PlanetCore.
+ *
+ * Copyright 2007 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+/ {
+ model = "EP8248E";
+ compatible = "fsl,ep8248e";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ aliases {
+ planetcore-SMC1 = &smc1;
+ planetcore-SCC1 = &scc1;
+ ethernet0 = ð0;
+ ethernet1 = ð1;
+ serial0 = &smc1;
+ serial1 = &scc1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,8248@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <32>;
+ i-cache-line-size = <32>;
+ d-cache-size = <16384>;
+ i-cache-size = <16384>;
+ timebase-frequency = <0>;
+ clock-frequency = <0>;
+ };
+ };
+
+ localbus {
+ compatible = "fsl,mpc8248-localbus",
+ "fsl,pq2-localbus",
+ "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <0xf0010100 0x40>;
+
+ ranges = <0 0 0xfc000000 0x04000000
+ 1 0 0xfa000000 0x00008000>;
+
+ flash@0,3800000 {
+ compatible = "cfi-flash";
+ reg = <0 0x3800000 0x800000>;
+ bank-width = <4>;
+ device-width = <2>;
+ };
+
+ bcsr@1,0 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <1 0 0x10>;
+ compatible = "fsl,ep8248e-bcsr";
+ ranges;
+
+ mdio {
+ device_type = "mdio";
+ compatible = "fsl,ep8248e-mdio-bitbang";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1 8 1>;
+
+ PHY0: ethernet-phy@0 {
+ interrupt-parent = <&PIC>;
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+
+ PHY1: ethernet-phy@1 {
+ interrupt-parent = <&PIC>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0>;
+ };
+
+ soc@f0000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "fsl,mpc8248", "fsl,pq2-soc", "simple-bus";
+ ranges = <0x00000000 0xf0000000 0x00053000>;
+
+ // Temporary -- will go away once kernel uses ranges for get_immrbase().
+ reg = <0xf0000000 0x00053000>;
+
+ cpm@119c0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #interrupt-cells = <2>;
+ compatible = "fsl,mpc8248-cpm", "fsl,cpm2",
+ "simple-bus";
+ reg = <0x119c0 0x30>;
+ ranges;
+
+ muram {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0x10000>;
+
+ data@0 {
+ compatible = "fsl,cpm-muram-data";
+ reg = <0 0x1100 0x1140
+ 0xec0 0x9800 0x800>;
+ };
+ };
+
+ brg@119f0 {
+ compatible = "fsl,mpc8248-brg",
+ "fsl,cpm2-brg",
+ "fsl,cpm-brg";
+ reg = <0x119f0 0x10 0x115f0 0x10>;
+ };
+
+ /* Monitor port/SMC1 */
+ smc1: serial@11a80 {
+ device_type = "serial";
+ compatible = "fsl,mpc8248-smc-uart",
+ "fsl,cpm2-smc-uart";
+ reg = <0x11a80 0x20 0x1100 0x40>;
+ interrupts = <4 8>;
+ interrupt-parent = <&PIC>;
+ fsl,cpm-brg = <7>;
+ fsl,cpm-command = <0x1d000000>;
+ linux,planetcore-label = "SMC1";
+ };
+
+ /* "Serial" port/SCC1 */
+ scc1: serial@11a00 {
+ device_type = "serial";
+ compatible = "fsl,mpc8248-scc-uart",
+ "fsl,cpm2-scc-uart";
+ reg = <0x11a00 0x20 0x8000 0x100>;
+ interrupts = <40 8>;
+ interrupt-parent = <&PIC>;
+ fsl,cpm-brg = <1>;
+ fsl,cpm-command = <0x00800000>;
+ linux,planetcore-label = "SCC1";
+ };
+
+ eth0: ethernet@11300 {
+ device_type = "network";
+ compatible = "fsl,mpc8248-fcc-enet",
+ "fsl,cpm2-fcc-enet";
+ reg = <0x11300 0x20 0x8400 0x100 0x11390 1>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <32 8>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY0>;
+ linux,network-index = <0>;
+ fsl,cpm-command = <0x12000300>;
+ };
+
+ eth1: ethernet@11320 {
+ device_type = "network";
+ compatible = "fsl,mpc8248-fcc-enet",
+ "fsl,cpm2-fcc-enet";
+ reg = <0x11320 0x20 0x8500 0x100 0x113b0 1>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <33 8>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY1>;
+ linux,network-index = <1>;
+ fsl,cpm-command = <0x16200300>;
+ };
+
+ usb@11b60 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc8248-usb",
+ "fsl,cpm2-usb";
+ reg = <0x11b60 0x18 0x8b00 0x100>;
+ interrupt-parent = <&PIC>;
+ interrupts = <11 8>;
+ fsl,cpm-command = <0x2e600000>;
+ };
+ };
+
+ PIC: interrupt-controller@10c00 {
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ reg = <0x10c00 0x80>;
+ compatible = "fsl,mpc8248-pic", "fsl,pq2-pic";
+ };
+ };
+};
diff --git a/arch/powerpc/boot/ep8248e.c b/arch/powerpc/boot/ep8248e.c
new file mode 100644
index 0000000..f57d14d
--- /dev/null
+++ b/arch/powerpc/boot/ep8248e.c
@@ -0,0 +1,55 @@
+/*
+ * Embedded Planet EP8248E with PlanetCore firmware
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "planetcore.h"
+#include "pq2.h"
+
+static char *table;
+static u64 mem_size;
+
+#include <io.h>
+
+static void platform_fixups(void)
+{
+ u64 val;
+
+ dt_fixup_memory(0, mem_size);
+ planetcore_set_mac_addrs(table);
+
+ if (!planetcore_get_decimal(table, PLANETCORE_KEY_CRYSTAL_HZ, &val)) {
+ printf("No PlanetCore crystal frequency key.\r\n");
+ return;
+ }
+
+ pq2_fixup_clocks(val);
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+ unsigned long r6, unsigned long r7)
+{
+ table = (char *)r3;
+ planetcore_prepare_table(table);
+
+ if (!planetcore_get_decimal(table, PLANETCORE_KEY_MB_RAM, &mem_size))
+ return;
+
+ mem_size *= 1024 * 1024;
+ simple_alloc_init(_end, mem_size - (unsigned long)_end, 32, 64);
+
+ fdt_init(_dtb_start);
+
+ planetcore_set_stdout_path(table);
+ serial_console_init();
+ platform_ops.fixups = platform_fixups;
+}
diff --git a/arch/powerpc/boot/wrapper b/arch/powerpc/boot/wrapper
index a7c4671..763a0c4 100755
--- a/arch/powerpc/boot/wrapper
+++ b/arch/powerpc/boot/wrapper
@@ -168,7 +168,7 @@ ps3)
ksection=.kernel:vmlinux.bin
isection=.kernel:initrd
;;
-ep88xc|ep405|redboot*)
+ep88xc|ep405|redboot*|ep8248e)
platformo="$object/fixed-head.o $object/$platform.o"
binary=y
;;
diff --git a/arch/powerpc/configs/ep8248e_defconfig b/arch/powerpc/configs/ep8248e_defconfig
new file mode 100644
index 0000000..01ad595
--- /dev/null
+++ b/arch/powerpc/configs/ep8248e_defconfig
@@ -0,0 +1,821 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.24-rc6
+# Fri Jan 11 14:02:06 2008
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+CONFIG_6xx=y
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_PPC_FPU=y
+CONFIG_PPC_STD_MMU=y
+CONFIG_PPC_STD_MMU_32=y
+# CONFIG_PPC_MM_SLICES is not set
+# CONFIG_SMP is not set
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+# CONFIG_PPC_UDBG_16550 is not set
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+# CONFIG_EXPERIMENTAL is not set
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+# CONFIG_BLK_DEV_INITRD is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+CONFIG_KALLSYMS_ALL=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+# CONFIG_MODULES is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_AS is not set
+CONFIG_IOSCHED_DEADLINE=y
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_DEFAULT_AS is not set
+CONFIG_DEFAULT_DEADLINE=y
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="deadline"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MULTIPLATFORM is not set
+CONFIG_PPC_82xx=y
+# CONFIG_PPC_83xx is not set
+# CONFIG_PPC_86xx is not set
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_MPC8272_ADS is not set
+# CONFIG_PQ2FADS is not set
+CONFIG_EP8248E=y
+# CONFIG_PQ2ADS is not set
+CONFIG_8260=y
+CONFIG_8272=y
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+CONFIG_CPM2=y
+CONFIG_PPC_CPM_NEW_BINDING=y
+# CONFIG_FSL_ULI1575 is not set
+CONFIG_CPM=y
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+CONFIG_BINFMT_MISC=y
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+CONFIG_PROC_DEVICETREE=y
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
+# CONFIG_SECCOMP is not set
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE="ep8248e.dts"
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_FSL_SOC=y
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0xc0000000
+CONFIG_BOOT_LOAD=0x00400000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+CONFIG_INET_TUNNEL=y
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_IP_VS is not set
+CONFIG_IPV6=y
+# CONFIG_IPV6_PRIVACY is not set
+# CONFIG_IPV6_ROUTER_PREF is not set
+# CONFIG_INET6_AH is not set
+# CONFIG_INET6_ESP is not set
+# CONFIG_INET6_IPCOMP is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+CONFIG_INET6_XFRM_MODE_TRANSPORT=y
+CONFIG_INET6_XFRM_MODE_TUNNEL=y
+CONFIG_INET6_XFRM_MODE_BEET=y
+CONFIG_IPV6_SIT=y
+# CONFIG_IPV6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+CONFIG_NETFILTER=y
+# CONFIG_NETFILTER_DEBUG is not set
+
+#
+# Core Netfilter Configuration
+#
+# CONFIG_NETFILTER_NETLINK is not set
+# CONFIG_NF_CONNTRACK_ENABLED is not set
+# CONFIG_NF_CONNTRACK is not set
+# CONFIG_NETFILTER_XTABLES is not set
+
+#
+# IP: Netfilter Configuration
+#
+# CONFIG_IP_NF_QUEUE is not set
+# CONFIG_IP_NF_IPTABLES is not set
+# CONFIG_IP_NF_ARPTABLES is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+# CONFIG_MTD_PARTITIONS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+CONFIG_MTD_CFI_NOSWAP=y
+# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set
+# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set
+CONFIG_MTD_CFI_GEOMETRY=y
+# CONFIG_MTD_MAP_BANK_WIDTH_1 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_2 is not set
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+# CONFIG_MTD_CFI_I1 is not set
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_OTP is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_RAM is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_MISC_DEVICES is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+CONFIG_DAVICOM_PHY=y
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_FIXED_PHY is not set
+CONFIG_MDIO_BITBANG=y
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_B44 is not set
+CONFIG_FS_ENET=y
+# CONFIG_FS_ENET_HAS_SCC is not set
+CONFIG_FS_ENET_HAS_FCC=y
+# CONFIG_FS_ENET_MDIO_FCC is not set
+CONFIG_NETDEV_1000=y
+CONFIG_NETDEV_10000=y
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_CPM=y
+CONFIG_SERIAL_CPM_CONSOLE=y
+CONFIG_SERIAL_CPM_SCC1=y
+# CONFIG_SERIAL_CPM_SCC2 is not set
+# CONFIG_SERIAL_CPM_SCC3 is not set
+CONFIG_SERIAL_CPM_SCC4=y
+# CONFIG_SERIAL_CPM_SMC1 is not set
+# CONFIG_SERIAL_CPM_SMC2 is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_NVRAM is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_JBD=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+CONFIG_AUTOFS4_FS=y
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_JFFS2_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=y
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+CONFIG_NLS_UTF8=y
+# CONFIG_UCC_SLOW is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+# CONFIG_CRC32 is not set
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_INSTRUMENTATION=y
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+# CONFIG_DETECT_SOFTLOCKUP is not set
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_KGDB_CONSOLE is not set
+CONFIG_BDI_SWITCH=y
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_MANAGER=y
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_WP512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=y
+# CONFIG_CRYPTO_CRYPTD is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_PPC_CLOCK is not set
+CONFIG_PPC_LIB_RHEAP=y
diff --git a/arch/powerpc/platforms/82xx/Kconfig b/arch/powerpc/platforms/82xx/Kconfig
index 541fbb8..4fad6c7 100644
--- a/arch/powerpc/platforms/82xx/Kconfig
+++ b/arch/powerpc/platforms/82xx/Kconfig
@@ -26,6 +26,19 @@ config PQ2FADS
help
This option enables support for the PQ2FADS board
+config EP8248E
+ bool "Embedded Planet EP8248E (a.k.a. CWH-PPC-8248N-VE)"
+ select 8272
+ select 8260
+ select FSL_SOC
+ select PPC_CPM_NEW_BINDING
+ select MDIO_BITBANG
+ help
+ This enables support for the Embedded Planet EP8248E board.
+
+ This board is also resold by Freescale as the QUICCStart
+ MPC8248 Evaluation System and/or the CWH-PPC-8248N-VE.
+
endchoice
config PQ2ADS
diff --git a/arch/powerpc/platforms/82xx/Makefile b/arch/powerpc/platforms/82xx/Makefile
index 68c8b0c..6cd5cd5 100644
--- a/arch/powerpc/platforms/82xx/Makefile
+++ b/arch/powerpc/platforms/82xx/Makefile
@@ -5,3 +5,4 @@ obj-$(CONFIG_MPC8272_ADS) += mpc8272_ads.o
obj-$(CONFIG_CPM2) += pq2.o
obj-$(CONFIG_PQ2_ADS_PCI_PIC) += pq2ads-pci-pic.o
obj-$(CONFIG_PQ2FADS) += pq2fads.o
+obj-$(CONFIG_EP8248E) += ep8248e.o
diff --git a/arch/powerpc/platforms/82xx/ep8248e.c b/arch/powerpc/platforms/82xx/ep8248e.c
new file mode 100644
index 0000000..2b4e87e
--- /dev/null
+++ b/arch/powerpc/platforms/82xx/ep8248e.c
@@ -0,0 +1,326 @@
+/*
+ * Embedded Planet EP8248E support
+ *
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/fsl_devices.h>
+#include <linux/mdio-bitbang.h>
+#include <linux/of_platform.h>
+
+#include <asm/io.h>
+#include <asm/cpm2.h>
+#include <asm/udbg.h>
+#include <asm/machdep.h>
+#include <asm/time.h>
+#include <asm/mpc8260.h>
+#include <asm/prom.h>
+
+#include <sysdev/fsl_soc.h>
+#include <sysdev/cpm2_pic.h>
+
+#include "pq2.h"
+
+static u8 __iomem *ep8248e_bcsr;
+static struct device_node *ep8248e_bcsr_node;
+
+#define BCSR7_SCC2_ENABLE 0x10
+
+#define BCSR8_PHY1_ENABLE 0x80
+#define BCSR8_PHY1_POWER 0x40
+#define BCSR8_PHY2_ENABLE 0x20
+#define BCSR8_PHY2_POWER 0x10
+#define BCSR8_MDIO_READ 0x04
+#define BCSR8_MDIO_CLOCK 0x02
+#define BCSR8_MDIO_DATA 0x01
+
+#define BCSR9_USB_ENABLE 0x80
+#define BCSR9_USB_POWER 0x40
+#define BCSR9_USB_HOST 0x20
+#define BCSR9_USB_FULL_SPEED_TARGET 0x10
+
+static void __init ep8248e_pic_init(void)
+{
+ struct device_node *np = of_find_compatible_node(NULL, NULL, "fsl,pq2-pic");
+ if (!np) {
+ printk(KERN_ERR "PIC init: can not find cpm-pic node\n");
+ return;
+ }
+
+ cpm2_pic_init(np);
+ of_node_put(np);
+}
+
+static void ep8248e_set_mdc(struct mdiobb_ctrl *ctrl, int level)
+{
+ if (level)
+ setbits8(&ep8248e_bcsr[8], BCSR8_MDIO_CLOCK);
+ else
+ clrbits8(&ep8248e_bcsr[8], BCSR8_MDIO_CLOCK);
+
+ /* Read back to flush the write. */
+ in_8(&ep8248e_bcsr[8]);
+}
+
+static void ep8248e_set_mdio_dir(struct mdiobb_ctrl *ctrl, int output)
+{
+ if (output)
+ clrbits8(&ep8248e_bcsr[8], BCSR8_MDIO_READ);
+ else
+ setbits8(&ep8248e_bcsr[8], BCSR8_MDIO_READ);
+
+ /* Read back to flush the write. */
+ in_8(&ep8248e_bcsr[8]);
+}
+
+static void ep8248e_set_mdio_data(struct mdiobb_ctrl *ctrl, int data)
+{
+ if (data)
+ setbits8(&ep8248e_bcsr[8], BCSR8_MDIO_DATA);
+ else
+ clrbits8(&ep8248e_bcsr[8], BCSR8_MDIO_DATA);
+
+ /* Read back to flush the write. */
+ in_8(&ep8248e_bcsr[8]);
+}
+
+static int ep8248e_get_mdio_data(struct mdiobb_ctrl *ctrl)
+{
+ return in_8(&ep8248e_bcsr[8]) & BCSR8_MDIO_DATA;
+}
+
+static const struct mdiobb_ops ep8248e_mdio_ops = {
+ .set_mdc = ep8248e_set_mdc,
+ .set_mdio_dir = ep8248e_set_mdio_dir,
+ .set_mdio_data = ep8248e_set_mdio_data,
+ .get_mdio_data = ep8248e_get_mdio_data,
+ .owner = THIS_MODULE,
+};
+
+static struct mdiobb_ctrl ep8248e_mdio_ctrl = {
+ .ops = &ep8248e_mdio_ops,
+};
+
+static int __devinit ep8248e_mdio_probe(struct of_device *ofdev,
+ const struct of_device_id *match)
+{
+ struct mii_bus *bus;
+ struct resource res;
+ struct device_node *node;
+ int ret, i;
+
+ node = of_get_parent(ofdev->node);
+ of_node_put(node);
+ if (node != ep8248e_bcsr_node)
+ return -ENODEV;
+
+ ret = of_address_to_resource(ofdev->node, 0, &res);
+ if (ret)
+ return ret;
+
+ bus = alloc_mdio_bitbang(&ep8248e_mdio_ctrl);
+ if (!bus)
+ return -ENOMEM;
+
+ bus->phy_mask = 0;
+ bus->irq = kmalloc(sizeof(int) * PHY_MAX_ADDR, GFP_KERNEL);
+
+ for (i = 0; i < PHY_MAX_ADDR; i++)
+ bus->irq[i] = -1;
+
+ bus->name = "ep8248e-mdio-bitbang";
+ bus->dev = &ofdev->dev;
+ bus->id = res.start;
+
+ return mdiobus_register(bus);
+}
+
+static int ep8248e_mdio_remove(struct of_device *ofdev)
+{
+ BUG();
+ return 0;
+}
+
+static const struct of_device_id ep8248e_mdio_match[] = {
+ {
+ .compatible = "fsl,ep8248e-mdio-bitbang",
+ },
+ {},
+};
+
+static struct of_platform_driver ep8248e_mdio_driver = {
+ .driver = {
+ .name = "ep8248e-mdio-bitbang",
+ },
+ .match_table = ep8248e_mdio_match,
+ .probe = ep8248e_mdio_probe,
+ .remove = ep8248e_mdio_remove,
+};
+
+struct cpm_pin {
+ int port, pin, flags;
+};
+
+static __initdata const struct cpm_pin ep8248e_pins[] = {
+ /* SMC1 */
+ {2, 4, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 5, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+
+ /* SCC1 */
+ {2, 14, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 15, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {3, 29, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {3, 30, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {3, 31, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+
+ /* FCC1 */
+ {0, 14, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 15, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 16, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 17, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 18, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 19, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 20, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 21, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 26, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {0, 27, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {0, 28, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {0, 29, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {0, 30, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {0, 31, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {2, 21, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 22, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+
+ /* FCC2 */
+ {1, 18, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 19, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 20, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 21, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 22, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {1, 23, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {1, 24, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {1, 25, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {1, 26, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 27, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 28, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 29, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {1, 30, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 31, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {2, 18, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 19, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+
+ /* I2C */
+ {4, 14, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {4, 15, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+
+ /* USB */
+ {2, 10, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 11, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 20, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {2, 24, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {3, 23, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {3, 24, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {3, 25, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+};
+
+static void __init init_ioports(void)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(ep8248e_pins); i++) {
+ const struct cpm_pin *pin = &ep8248e_pins[i];
+ cpm2_set_pin(pin->port, pin->pin, pin->flags);
+ }
+
+ cpm2_smc_clk_setup(CPM_CLK_SMC1, CPM_BRG7);
+ cpm2_clk_setup(CPM_CLK_SCC1, CPM_BRG1, CPM_CLK_RX);
+ cpm2_clk_setup(CPM_CLK_SCC1, CPM_BRG1, CPM_CLK_TX);
+ cpm2_clk_setup(CPM_CLK_SCC3, CPM_CLK8, CPM_CLK_TX); /* USB */
+ cpm2_clk_setup(CPM_CLK_FCC1, CPM_CLK11, CPM_CLK_RX);
+ cpm2_clk_setup(CPM_CLK_FCC1, CPM_CLK10, CPM_CLK_TX);
+ cpm2_clk_setup(CPM_CLK_FCC2, CPM_CLK13, CPM_CLK_RX);
+ cpm2_clk_setup(CPM_CLK_FCC2, CPM_CLK14, CPM_CLK_TX);
+}
+
+static void __init ep8248e_setup_arch(void)
+{
+ if (ppc_md.progress)
+ ppc_md.progress("ep8248e_setup_arch()", 0);
+
+ cpm2_reset();
+
+ /* When this is set, snooping CPM DMA from RAM causes
+ * machine checks. See erratum SIU18.
+ */
+ clrbits32(&cpm2_immr->im_siu_conf.siu_82xx.sc_bcr, MPC82XX_BCR_PLDP);
+
+ ep8248e_bcsr_node =
+ of_find_compatible_node(NULL, NULL, "fsl,ep8248e-bcsr");
+ if (!ep8248e_bcsr_node) {
+ printk(KERN_ERR "No bcsr in device tree\n");
+ return;
+ }
+
+ ep8248e_bcsr = of_iomap(ep8248e_bcsr_node, 0);
+ if (!ep8248e_bcsr) {
+ printk(KERN_ERR "Cannot map BCSR registers\n");
+ of_node_put(ep8248e_bcsr_node);
+ ep8248e_bcsr_node = NULL;
+ return;
+ }
+
+ setbits8(&ep8248e_bcsr[7], BCSR7_SCC2_ENABLE);
+ setbits8(&ep8248e_bcsr[8], BCSR8_PHY1_ENABLE | BCSR8_PHY1_POWER |
+ BCSR8_PHY2_ENABLE | BCSR8_PHY2_POWER);
+
+ init_ioports();
+
+ if (ppc_md.progress)
+ ppc_md.progress("ep8248e_setup_arch(), finish", 0);
+}
+
+static __initdata const struct of_device_id of_bus_ids[] = {
+ { .name = "soc", },
+ { .name = "cpm", },
+ { .name = "localbus", },
+ { .compatible = "fsl,ep8248e-bcsr", },
+ {},
+};
+
+static int __init declare_of_platform_devices(void)
+{
+ of_platform_bus_probe(NULL, of_bus_ids, NULL);
+ of_register_platform_driver(&ep8248e_mdio_driver);
+
+ return 0;
+}
+machine_device_initcall(ep8248e, declare_of_platform_devices);
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init ep8248e_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+ return of_flat_dt_is_compatible(root, "fsl,ep8248e");
+}
+
+define_machine(ep8248e)
+{
+ .name = "Embedded Planet EP8248E",
+ .probe = ep8248e_probe,
+ .setup_arch = ep8248e_setup_arch,
+ .init_IRQ = ep8248e_pic_init,
+ .get_irq = cpm2_get_irq,
+ .calibrate_decr = generic_calibrate_decr,
+ .restart = pq2_restart,
+ .progress = udbg_progress,
+};
diff --git a/include/asm-powerpc/mpc8260.h b/include/asm-powerpc/mpc8260.h
index e0d4807..03317e1 100644
--- a/include/asm-powerpc/mpc8260.h
+++ b/include/asm-powerpc/mpc8260.h
@@ -8,6 +8,7 @@
#ifndef __ASM_POWERPC_MPC8260_H__
#define __ASM_POWERPC_MPC8260_H__
+#define MPC82XX_BCR_PLDP 0x00800000 /* Pipeline Maximum Depth */
#ifdef CONFIG_8260
--
1.5.3.8
^ permalink raw reply related
* [PATCH 1/2] 8xx: Analogue & Micro Adder875 board support.
From: Scott Wood @ 2008-01-15 23:30 UTC (permalink / raw)
To: vitb, galak; +Cc: linuxppc-dev
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
arch/powerpc/Kconfig | 3 +
arch/powerpc/boot/.gitignore | 1 +
arch/powerpc/boot/Makefile | 6 +-
arch/powerpc/boot/dts/adder875-redboot.dts | 182 +++++
arch/powerpc/boot/dts/adder875-uboot.dts | 181 +++++
arch/powerpc/boot/redboot-8xx.c | 58 ++
arch/powerpc/boot/redboot.h | 56 ++
arch/powerpc/boot/wrapper | 2 +-
arch/powerpc/configs/adder875-redboot_defconfig | 798 +++++++++++++++++++++++
arch/powerpc/configs/adder875-uboot_defconfig | 798 +++++++++++++++++++++++
arch/powerpc/platforms/8xx/Kconfig | 9 +
arch/powerpc/platforms/8xx/Makefile | 1 +
arch/powerpc/platforms/8xx/adder875.c | 120 ++++
13 files changed, 2213 insertions(+), 2 deletions(-)
create mode 100644 arch/powerpc/boot/dts/adder875-redboot.dts
create mode 100644 arch/powerpc/boot/dts/adder875-uboot.dts
create mode 100644 arch/powerpc/boot/redboot-8xx.c
create mode 100644 arch/powerpc/boot/redboot.h
create mode 100644 arch/powerpc/configs/adder875-redboot_defconfig
create mode 100644 arch/powerpc/configs/adder875-uboot_defconfig
create mode 100644 arch/powerpc/platforms/8xx/adder875.c
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index 66a3d8c..47fe256 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -140,6 +140,9 @@ config DEFAULT_UIMAGE
Used to allow a board to specify it wants a uImage built by default
default n
+config REDBOOT
+ bool
+
config PPC64_SWSUSP
bool
depends on PPC64 && (BROKEN || (PPC_PMAC64 && EXPERIMENTAL))
diff --git a/arch/powerpc/boot/.gitignore b/arch/powerpc/boot/.gitignore
index 65f4118..a424be6 100644
--- a/arch/powerpc/boot/.gitignore
+++ b/arch/powerpc/boot/.gitignore
@@ -30,6 +30,7 @@ zImage.*lds
zImage.miboot
zImage.pmac
zImage.pseries
+zImage.redboot*
zImage.sandpoint
zImage.vmode
zconf.h
diff --git a/arch/powerpc/boot/Makefile b/arch/powerpc/boot/Makefile
index d1e625c..08bf7aa 100644
--- a/arch/powerpc/boot/Makefile
+++ b/arch/powerpc/boot/Makefile
@@ -62,7 +62,7 @@ src-plat := of.c cuboot-52xx.c cuboot-83xx.c cuboot-85xx.c holly.c \
ps3-head.S ps3-hvcall.S ps3.c treeboot-bamboo.c cuboot-8xx.c \
cuboot-pq2.c cuboot-sequoia.c treeboot-walnut.c cuboot-bamboo.c \
fixed-head.S ep88xc.c cuboot-hpc2.c ep405.c cuboot-taishan.c \
- cuboot-katmai.c cuboot-rainier.c
+ cuboot-katmai.c cuboot-rainier.c redboot-8xx.c
src-boot := $(src-wlib) $(src-plat) empty.c
src-boot := $(addprefix $(obj)/, $(src-boot))
@@ -208,6 +208,10 @@ image-$(CONFIG_TAISHAN) += cuImage.taishan
image-$(CONFIG_KATMAI) += cuImage.katmai
endif
+ifneq ($(CONFIG_REDBOOT),"")
+image-$(CONFIG_PPC_8xx) += zImage.redboot-8xx
+endif
+
# For 32-bit powermacs, build the COFF and miboot images
# as well as the ELF images.
ifeq ($(CONFIG_PPC32),y)
diff --git a/arch/powerpc/boot/dts/adder875-redboot.dts b/arch/powerpc/boot/dts/adder875-redboot.dts
new file mode 100644
index 0000000..e70db51
--- /dev/null
+++ b/arch/powerpc/boot/dts/adder875-redboot.dts
@@ -0,0 +1,182 @@
+/*
+ * Device Tree Source for MPC885 ADS running RedBoot
+ *
+ * Copyright 2006 MontaVista Software, Inc.
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+/ {
+ model = "Analogue & Micro Adder MPC875";
+ compatible = "analogue-and-micro,adder875";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ aliases {
+ console = &console;
+ ethernet0 = ð0;
+ ethernet1 = ð1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,875@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <16>;
+ i-cache-line-size = <16>;
+ d-cache-size = <8192>;
+ i-cache-size = <8192>;
+ timebase-frequency = <0>;
+ bus-frequency = <0>;
+ clock-frequency = <0>;
+ interrupts = <15 2>; // decrementer interrupt
+ interrupt-parent = <&PIC>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x01000000>;
+ };
+
+ localbus@fa200100 {
+ compatible = "fsl,mpc885-localbus", "fsl,pq1-localbus",
+ "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <0xfa200100 0x40>;
+
+ ranges = <
+ 0 0 0xfe000000 0x00800000
+ 2 0 0xfa100000 0x00008000
+ >;
+
+ flash@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 0x800000>;
+ bank-width = <4>;
+ device-width = <2>;
+ };
+ };
+
+ soc@fa200000 {
+ compatible = "fsl,mpc875", "fsl,pq1-soc", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ ranges = <0 0xfa200000 0x00004000>;
+
+ // Temporary until get_immrbase() is fixed.
+ reg = <0xfa200000 0x4000>;
+
+ mdio@e00 {
+ compatible = "fsl,mpc875-fec-mdio", "fsl,pq1-fec-mdio";
+ reg = <0xe00 0x188>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PHY0: ethernet-phy@0 {
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+
+ PHY1: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ eth0: ethernet@e00 {
+ device_type = "network";
+ compatible = "fsl,mpc875-fec-enet",
+ "fsl,pq1-fec-enet";
+ reg = <0xe00 0x188>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <3 1>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY0>;
+ linux,network-index = <0>;
+ };
+
+ eth1: ethernet@1e00 {
+ device_type = "network";
+ compatible = "fsl,mpc875-fec-enet",
+ "fsl,pq1-fec-enet";
+ reg = <0x1e00 0x188>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <7 1>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY1>;
+ linux,network-index = <1>;
+ };
+
+ PIC: interrupt-controller@0 {
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0 0x24>;
+ compatible = "fsl,mpc875-pic", "fsl,pq1-pic";
+ };
+
+ cpm@9c0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc875-cpm", "fsl,cpm1";
+ interrupts = <0>; // cpm error interrupt
+ interrupt-parent = <&CPM_PIC>;
+ reg = <0x9c0 0x40>;
+ ranges;
+
+ muram {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x2000 0x2000>;
+
+ data@0 {
+ compatible = "fsl,cpm-muram-data";
+ reg = <0 0x1c00>;
+ };
+ };
+
+ brg@9f0 {
+ compatible = "fsl,mpc875-brg",
+ "fsl,cpm1-brg",
+ "fsl,cpm-brg";
+ reg = <0x9f0 0x10>;
+ };
+
+ CPM_PIC: interrupt-controller@930 {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupts = <5 2 0 2>;
+ interrupt-parent = <&PIC>;
+ reg = <0x930 0x20>;
+ compatible = "fsl,mpc875-cpm-pic",
+ "fsl,cpm1-pic";
+ };
+
+ console: serial@a80 {
+ device_type = "serial";
+ compatible = "fsl,mpc875-smc-uart",
+ "fsl,cpm1-smc-uart";
+ reg = <0xa80 0x10 0x3e80 0x40>;
+ interrupts = <4>;
+ interrupt-parent = <&CPM_PIC>;
+ fsl,cpm-brg = <1>;
+ fsl,cpm-command = <0x0090>;
+ current-speed = <115200>;
+ };
+ };
+ };
+
+ chosen {
+ linux,stdout-path = &console;
+ };
+};
diff --git a/arch/powerpc/boot/dts/adder875-uboot.dts b/arch/powerpc/boot/dts/adder875-uboot.dts
new file mode 100644
index 0000000..983acf4
--- /dev/null
+++ b/arch/powerpc/boot/dts/adder875-uboot.dts
@@ -0,0 +1,181 @@
+/*
+ * Device Tree Source for MPC885 ADS running U-Boot
+ *
+ * Copyright 2006 MontaVista Software, Inc.
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+/ {
+ model = "Analogue & Micro Adder MPC875";
+ compatible = "analogue-and-micro,adder875";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ aliases {
+ console = &console;
+ ethernet0 = ð0;
+ ethernet1 = ð1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,875@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <16>;
+ i-cache-line-size = <16>;
+ d-cache-size = <8192>;
+ i-cache-size = <8192>;
+ timebase-frequency = <0>;
+ bus-frequency = <0>;
+ clock-frequency = <0>;
+ interrupts = <15 2>; // decrementer interrupt
+ interrupt-parent = <&PIC>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x01000000>;
+ };
+
+ localbus@ff000100 {
+ compatible = "fsl,mpc885-localbus", "fsl,pq1-localbus",
+ "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <0xff000100 0x40>;
+
+ ranges = <
+ 0 0 0xfe000000 0x01000000
+ >;
+
+ flash@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 0x800000>;
+ bank-width = <4>;
+ device-width = <2>;
+ };
+ };
+
+ soc@ff000000 {
+ compatible = "fsl,mpc875", "fsl,pq1-soc", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ ranges = <0 0xff000000 0x00004000>;
+
+ // Temporary until get_immrbase() is fixed.
+ reg = <0xff000000 0x4000>;
+
+ mdio@e00 {
+ compatible = "fsl,mpc875-fec-mdio", "fsl,pq1-fec-mdio";
+ reg = <0xe00 0x188>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PHY0: ethernet-phy@0 {
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+
+ PHY1: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ eth0: ethernet@e00 {
+ device_type = "network";
+ compatible = "fsl,mpc875-fec-enet",
+ "fsl,pq1-fec-enet";
+ reg = <0xe00 0x188>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <3 1>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY0>;
+ linux,network-index = <0>;
+ };
+
+ eth1: ethernet@1e00 {
+ device_type = "network";
+ compatible = "fsl,mpc875-fec-enet",
+ "fsl,pq1-fec-enet";
+ reg = <0x1e00 0x188>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <7 1>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY1>;
+ linux,network-index = <1>;
+ };
+
+ PIC: interrupt-controller@0 {
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0 0x24>;
+ compatible = "fsl,mpc875-pic", "fsl,pq1-pic";
+ };
+
+ cpm@9c0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc875-cpm", "fsl,cpm1";
+ interrupts = <0>; // cpm error interrupt
+ interrupt-parent = <&CPM_PIC>;
+ reg = <0x9c0 0x40>;
+ ranges;
+
+ muram {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x2000 0x2000>;
+
+ data@0 {
+ compatible = "fsl,cpm-muram-data";
+ reg = <0 0x1c00>;
+ };
+ };
+
+ brg@9f0 {
+ compatible = "fsl,mpc875-brg",
+ "fsl,cpm1-brg",
+ "fsl,cpm-brg";
+ reg = <0x9f0 0x10>;
+ };
+
+ CPM_PIC: interrupt-controller@930 {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupts = <5 2 0 2>;
+ interrupt-parent = <&PIC>;
+ reg = <0x930 0x20>;
+ compatible = "fsl,mpc875-cpm-pic",
+ "fsl,cpm1-pic";
+ };
+
+ console: serial@a80 {
+ device_type = "serial";
+ compatible = "fsl,mpc875-smc-uart",
+ "fsl,cpm1-smc-uart";
+ reg = <0xa80 0x10 0x3e80 0x40>;
+ interrupts = <4>;
+ interrupt-parent = <&CPM_PIC>;
+ fsl,cpm-brg = <1>;
+ fsl,cpm-command = <0x0090>;
+ current-speed = <115200>;
+ };
+ };
+ };
+
+ chosen {
+ linux,stdout-path = &console;
+ };
+};
diff --git a/arch/powerpc/boot/redboot-8xx.c b/arch/powerpc/boot/redboot-8xx.c
new file mode 100644
index 0000000..f7945ad
--- /dev/null
+++ b/arch/powerpc/boot/redboot-8xx.c
@@ -0,0 +1,58 @@
+/*
+ * RedBoot firmware support
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "redboot.h"
+#include "fsl-soc.h"
+#include "io.h"
+
+static bd_t bd;
+BSS_STACK(4096);
+
+#define MHZ(x) ((x + 500000) / 1000000)
+
+static void platform_fixups(void)
+{
+ void *node;
+
+ dt_fixup_memory(bd.bi_memstart, bd.bi_memsize);
+ dt_fixup_mac_addresses(bd.bi_enetaddr);
+ dt_fixup_cpu_clocks(bd.bi_intfreq, bd.bi_busfreq / 16, bd.bi_busfreq);
+
+ node = finddevice("/soc/cpm/brg");
+ if (node) {
+ printf("BRG clock-frequency <- 0x%x (%dMHz)\r\n",
+ bd.bi_busfreq, MHZ(bd.bi_busfreq));
+ setprop(node, "clock-frequency", &bd.bi_busfreq, 4);
+ }
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+ unsigned long r6, unsigned long r7)
+{
+ memcpy(&bd, (char *)r3, sizeof(bd));
+
+ if (bd.bi_tag != 0x42444944)
+ return;
+
+ simple_alloc_init(_end,
+ bd.bi_memstart + bd.bi_memsize - (unsigned long)_end,
+ 32, 64);
+
+ fdt_init(_dtb_start);
+ serial_console_init();
+ platform_ops.fixups = platform_fixups;
+
+ loader_info.cmdline = (char *)bd.bi_cmdline;
+ loader_info.cmdline_len = strlen((char *)bd.bi_cmdline);
+}
diff --git a/arch/powerpc/boot/redboot.h b/arch/powerpc/boot/redboot.h
new file mode 100644
index 0000000..ace0b7f
--- /dev/null
+++ b/arch/powerpc/boot/redboot.h
@@ -0,0 +1,56 @@
+#ifndef _PPC_REDBOOT_H
+#define _PPC_REDBOOT_H
+
+//=========================================================================
+// include/asm-ppc/redboot.h
+// Copyright (c) 2002, 2003 Gary Thomas (<gary@mlbassoc.com>
+// Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
+
+//
+// Board specific details, as provided by RedBoot
+//
+
+/* A Board Information structure that is given to a program when
+ * RedBoot starts it up. Note: not all fields make sense for all
+ * architectures and it's up to the platform specific code to fill
+ * in the details.
+ */
+typedef struct bd_info {
+ unsigned int bi_tag; /* Should be 0x42444944 "BDID" */
+ unsigned int bi_size; /* Size of this structure */
+ unsigned int bi_revision; /* revision of this structure */
+ unsigned int bi_bdate; /* bootstrap date, i.e. 0x19971106 */
+ unsigned int bi_memstart; /* Memory start address */
+ unsigned int bi_memsize; /* Memory (end) size in bytes */
+ unsigned int bi_intfreq; /* Internal Freq, in Hz */
+ unsigned int bi_busfreq; /* Bus Freq, in Hz */
+ unsigned int bi_cpmfreq; /* CPM Freq, in Hz */
+ unsigned int bi_brgfreq; /* BRG Freq, in Hz */
+ unsigned int bi_vco; /* VCO Out from PLL */
+ unsigned int bi_pci_freq; /* PCI Freq, in Hz */
+ unsigned int bi_baudrate; /* Default console baud rate */
+ unsigned int bi_immr; /* IMMR when called from boot rom */
+ unsigned char bi_enetaddr[6];
+ unsigned int bi_flashbase; /* Physical address of FLASH memory */
+ unsigned int bi_flashsize; /* Length of FLASH memory */
+ int bi_flashwidth; /* Width (8,16,32,64) */
+ unsigned char *bi_cmdline; /* Pointer to command line */
+ unsigned char bi_esa[3][6]; /* Ethernet station addresses */
+ unsigned int bi_ramdisk_begin, bi_ramdisk_end;
+ struct { /* Information about [main] video screen */
+ short x_res; /* Horizontal resolution in pixels */
+ short y_res; /* Vertical resolution in pixels */
+ short bpp; /* Bits/pixel */
+ short mode; /* Type of pixels (packed, indexed) */
+ unsigned long fb; /* Pointer to frame buffer (pixel) memory */
+ } bi_video;
+ void (*bi_cputc)(char); /* Write a character to the RedBoot console */
+ char (*bi_cgetc)(void); /* Read a character from the RedBoot console */
+ int (*bi_ctstc)(void); /* Test for input on the RedBoot console */
+} bd_t;
+
+#define BI_REV 0x0102 /* Version 1.02 */
+
+#define bi_pci_busfreq bi_pci_freq
+#define bi_immr_base bi_immr
+#endif
diff --git a/arch/powerpc/boot/wrapper b/arch/powerpc/boot/wrapper
index 154df05..a7c4671 100755
--- a/arch/powerpc/boot/wrapper
+++ b/arch/powerpc/boot/wrapper
@@ -168,7 +168,7 @@ ps3)
ksection=.kernel:vmlinux.bin
isection=.kernel:initrd
;;
-ep88xc|ep405)
+ep88xc|ep405|redboot*)
platformo="$object/fixed-head.o $object/$platform.o"
binary=y
;;
diff --git a/arch/powerpc/configs/adder875-redboot_defconfig b/arch/powerpc/configs/adder875-redboot_defconfig
new file mode 100644
index 0000000..ceda44d
--- /dev/null
+++ b/arch/powerpc/configs/adder875-redboot_defconfig
@@ -0,0 +1,798 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.24-rc3
+# Mon Dec 10 11:29:32 2007
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+# CONFIG_6xx is not set
+# CONFIG_PPC_85xx is not set
+CONFIG_PPC_8xx=y
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_8xx=y
+# CONFIG_PPC_MM_SLICES is not set
+CONFIG_NOT_COHERENT_CACHE=y
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+# CONFIG_PPC_UDBG_16550 is not set
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+CONFIG_REDBOOT=y
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+# CONFIG_BLK_DEV_INITRD is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+# CONFIG_SYSCTL_SYSCALL is not set
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+# CONFIG_ELF_CORE is not set
+# CONFIG_BASE_FULL is not set
+# CONFIG_FUTEX is not set
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+CONFIG_SLUB_DEBUG=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=1
+# CONFIG_MODULES is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_AS is not set
+CONFIG_IOSCHED_DEADLINE=y
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_DEFAULT_AS is not set
+CONFIG_DEFAULT_DEADLINE=y
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="deadline"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+CONFIG_CPM1=y
+# CONFIG_MPC8XXFADS is not set
+# CONFIG_MPC86XADS is not set
+# CONFIG_MPC885ADS is not set
+# CONFIG_PPC_EP88XC is not set
+CONFIG_PPC_ADDER875=y
+
+#
+# MPC8xx CPM Options
+#
+
+#
+# Generic MPC8xx Options
+#
+CONFIG_8xx_COPYBACK=y
+# CONFIG_8xx_CPU6 is not set
+CONFIG_8xx_CPU15=y
+CONFIG_NO_UCODE_PATCH v3=y
+# CONFIG_USB_SOF_UCODE_PATCH v3 is not set
+# CONFIG_I2C_SPI_UCODE_PATCH v3 is not set
+# CONFIG_I2C_SPI_SMC1_UCODE_PATCH v3 is not set
+# CONFIG_PQ2ADS is not set
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPM2 is not set
+CONFIG_PPC_CPM_NEW_BINDING=y
+# CONFIG_FSL_ULI1575 is not set
+CONFIG_CPM=y
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+# CONFIG_HZ_250 is not set
+# CONFIG_HZ_300 is not set
+CONFIG_HZ_1000=y
+CONFIG_HZ=1000
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_MATH_EMULATION is not set
+# CONFIG_8XX_MINIMAL_FPEMU is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+# CONFIG_PROC_DEVICETREE is not set
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
+# CONFIG_SECCOMP is not set
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE="adder875-redboot.dts"
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_FSL_SOC=y
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_PCI_QSPAN is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_START=0xfd000000
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_BOOT_LOAD=0x00400000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+# CONFIG_IP_PNP_DHCP is not set
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+# CONFIG_MTD_PARTITIONS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_CFI_FLAGADM is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+# CONFIG_BLK_DEV is not set
+# CONFIG_MISC_DEVICES is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+CONFIG_DAVICOM_PHY=y
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_B44 is not set
+CONFIG_FS_ENET=y
+# CONFIG_FS_ENET_HAS_SCC is not set
+CONFIG_FS_ENET_HAS_FEC=y
+CONFIG_FS_ENET_MDIO_FEC=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_KEYBOARD_ATKBD=y
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_LIFEBOOK=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_I8042=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_CPM=y
+CONFIG_SERIAL_CPM_CONSOLE=y
+# CONFIG_SERIAL_CPM_SCC1 is not set
+# CONFIG_SERIAL_CPM_SCC2 is not set
+# CONFIG_SERIAL_CPM_SCC3 is not set
+# CONFIG_SERIAL_CPM_SCC4 is not set
+CONFIG_SERIAL_CPM_SMC1=y
+CONFIG_SERIAL_CPM_SMC2=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=y
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+# CONFIG_EXT2_FS is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_INOTIFY is not set
+# CONFIG_QUOTA is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+# CONFIG_PROC_KCORE is not set
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS2_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+# CONFIG_NLS is not set
+# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+# CONFIG_CRC32 is not set
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_INSTRUMENTATION=y
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_BDI_SWITCH is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+# CONFIG_CRYPTO is not set
+# CONFIG_PPC_CLOCK is not set
+CONFIG_PPC_LIB_RHEAP=y
diff --git a/arch/powerpc/configs/adder875-uboot_defconfig b/arch/powerpc/configs/adder875-uboot_defconfig
new file mode 100644
index 0000000..bb97223
--- /dev/null
+++ b/arch/powerpc/configs/adder875-uboot_defconfig
@@ -0,0 +1,798 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.24-rc3
+# Mon Dec 10 11:29:32 2007
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+# CONFIG_6xx is not set
+# CONFIG_PPC_85xx is not set
+CONFIG_PPC_8xx=y
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_8xx=y
+# CONFIG_PPC_MM_SLICES is not set
+CONFIG_NOT_COHERENT_CACHE=y
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+# CONFIG_PPC_UDBG_16550 is not set
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+CONFIG_REDBOOT=y
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+# CONFIG_BLK_DEV_INITRD is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+# CONFIG_SYSCTL_SYSCALL is not set
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+# CONFIG_ELF_CORE is not set
+# CONFIG_BASE_FULL is not set
+# CONFIG_FUTEX is not set
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+CONFIG_SLUB_DEBUG=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=1
+# CONFIG_MODULES is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_AS is not set
+CONFIG_IOSCHED_DEADLINE=y
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_DEFAULT_AS is not set
+CONFIG_DEFAULT_DEADLINE=y
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="deadline"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+CONFIG_CPM1=y
+# CONFIG_MPC8XXFADS is not set
+# CONFIG_MPC86XADS is not set
+# CONFIG_MPC885ADS is not set
+# CONFIG_PPC_EP88XC is not set
+CONFIG_PPC_ADDER875=y
+
+#
+# MPC8xx CPM Options
+#
+
+#
+# Generic MPC8xx Options
+#
+CONFIG_8xx_COPYBACK=y
+# CONFIG_8xx_CPU6 is not set
+CONFIG_8xx_CPU15=y
+CONFIG_NO_UCODE_PATCH v3=y
+# CONFIG_USB_SOF_UCODE_PATCH v3 is not set
+# CONFIG_I2C_SPI_UCODE_PATCH v3 is not set
+# CONFIG_I2C_SPI_SMC1_UCODE_PATCH v3 is not set
+# CONFIG_PQ2ADS is not set
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPM2 is not set
+CONFIG_PPC_CPM_NEW_BINDING=y
+# CONFIG_FSL_ULI1575 is not set
+CONFIG_CPM=y
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+# CONFIG_HZ_250 is not set
+# CONFIG_HZ_300 is not set
+CONFIG_HZ_1000=y
+CONFIG_HZ=1000
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_MATH_EMULATION is not set
+# CONFIG_8XX_MINIMAL_FPEMU is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+# CONFIG_PROC_DEVICETREE is not set
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
+# CONFIG_SECCOMP is not set
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE="adder875-uboot.dts"
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_FSL_SOC=y
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_PCI_QSPAN is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_START=0xfd000000
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_BOOT_LOAD=0x00400000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+# CONFIG_IP_PNP_DHCP is not set
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+# CONFIG_MTD_PARTITIONS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_CFI_FLAGADM is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+# CONFIG_BLK_DEV is not set
+# CONFIG_MISC_DEVICES is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+CONFIG_DAVICOM_PHY=y
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_B44 is not set
+CONFIG_FS_ENET=y
+# CONFIG_FS_ENET_HAS_SCC is not set
+CONFIG_FS_ENET_HAS_FEC=y
+CONFIG_FS_ENET_MDIO_FEC=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_KEYBOARD_ATKBD=y
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_LIFEBOOK=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_I8042=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_CPM=y
+CONFIG_SERIAL_CPM_CONSOLE=y
+# CONFIG_SERIAL_CPM_SCC1 is not set
+# CONFIG_SERIAL_CPM_SCC2 is not set
+# CONFIG_SERIAL_CPM_SCC3 is not set
+# CONFIG_SERIAL_CPM_SCC4 is not set
+CONFIG_SERIAL_CPM_SMC1=y
+CONFIG_SERIAL_CPM_SMC2=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=y
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+# CONFIG_EXT2_FS is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_INOTIFY is not set
+# CONFIG_QUOTA is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+# CONFIG_PROC_KCORE is not set
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS2_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+# CONFIG_NLS is not set
+# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+# CONFIG_CRC32 is not set
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_INSTRUMENTATION=y
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_BDI_SWITCH is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+# CONFIG_CRYPTO is not set
+# CONFIG_PPC_CLOCK is not set
+CONFIG_PPC_LIB_RHEAP=y
diff --git a/arch/powerpc/platforms/8xx/Kconfig b/arch/powerpc/platforms/8xx/Kconfig
index 91fbe42..7fd224c 100644
--- a/arch/powerpc/platforms/8xx/Kconfig
+++ b/arch/powerpc/platforms/8xx/Kconfig
@@ -44,6 +44,15 @@ config PPC_EP88XC
This board is also resold by Freescale as the QUICCStart
MPC885 Evaluation System and/or the CWH-PPC-885XN-VE.
+config PPC_ADDER875
+ bool "Analogue & Micro Adder 875"
+ select CPM1
+ select PPC_CPM_NEW_BINDING
+ select REDBOOT
+ help
+ This enables support for the Analogue & Micro Adder 875
+ board.
+
endchoice
menu "Freescale Ethernet driver platform-specific options"
diff --git a/arch/powerpc/platforms/8xx/Makefile b/arch/powerpc/platforms/8xx/Makefile
index 8b70980..7b71d9c 100644
--- a/arch/powerpc/platforms/8xx/Makefile
+++ b/arch/powerpc/platforms/8xx/Makefile
@@ -5,3 +5,4 @@ obj-$(CONFIG_PPC_8xx) += m8xx_setup.o
obj-$(CONFIG_MPC885ADS) += mpc885ads_setup.o
obj-$(CONFIG_MPC86XADS) += mpc86xads_setup.o
obj-$(CONFIG_PPC_EP88XC) += ep88xc.o
+obj-$(CONFIG_PPC_ADDER875) += adder875.o
diff --git a/arch/powerpc/platforms/8xx/adder875.c b/arch/powerpc/platforms/8xx/adder875.c
new file mode 100644
index 0000000..73c22a4
--- /dev/null
+++ b/arch/powerpc/platforms/8xx/adder875.c
@@ -0,0 +1,120 @@
+/* Analogue & Micro Adder MPC875 board support
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/fs_enet_pd.h>
+#include <linux/of_platform.h>
+
+#include <asm/time.h>
+#include <asm/machdep.h>
+#include <asm/commproc.h>
+#include <asm/fs_pd.h>
+#include <asm/udbg.h>
+#include <asm/prom.h>
+
+#include <sysdev/commproc.h>
+
+struct cpm_pin {
+ int port, pin, flags;
+};
+
+static __initdata const struct cpm_pin adder875_pins[] = {
+ /* SMC1 */
+ {CPM_PORTB, 24, CPM_PIN_INPUT}, /* RX */
+ {CPM_PORTB, 25, CPM_PIN_INPUT | CPM_PIN_SECONDARY}, /* TX */
+
+ /* MII1 */
+ {CPM_PORTA, 0, CPM_PIN_INPUT},
+ {CPM_PORTA, 1, CPM_PIN_INPUT},
+ {CPM_PORTA, 2, CPM_PIN_INPUT},
+ {CPM_PORTA, 3, CPM_PIN_INPUT},
+ {CPM_PORTA, 4, CPM_PIN_OUTPUT},
+ {CPM_PORTA, 10, CPM_PIN_OUTPUT},
+ {CPM_PORTA, 11, CPM_PIN_OUTPUT},
+ {CPM_PORTB, 19, CPM_PIN_INPUT},
+ {CPM_PORTB, 31, CPM_PIN_INPUT},
+ {CPM_PORTC, 12, CPM_PIN_INPUT},
+ {CPM_PORTC, 13, CPM_PIN_INPUT},
+ {CPM_PORTE, 30, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 31, CPM_PIN_OUTPUT},
+
+ /* MII2 */
+ {CPM_PORTE, 14, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {CPM_PORTE, 15, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {CPM_PORTE, 16, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 17, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {CPM_PORTE, 18, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {CPM_PORTE, 19, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {CPM_PORTE, 20, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {CPM_PORTE, 21, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 22, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 23, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 24, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 25, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 26, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 27, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 28, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 29, CPM_PIN_OUTPUT},
+};
+
+static void __init init_ioports(void)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(adder875_pins); i++) {
+ const struct cpm_pin *pin = &adder875_pins[i];
+ cpm1_set_pin(pin->port, pin->pin, pin->flags);
+ }
+
+ cpm1_clk_setup(CPM_CLK_SMC1, CPM_BRG1, CPM_CLK_RTX);
+
+ /* Set FEC1 and FEC2 to MII mode */
+ clrbits32(&mpc8xx_immr->im_cpm.cp_cptr, 0x00000180);
+}
+
+static void __init adder875_setup(void)
+{
+ cpm_reset();
+ init_ioports();
+}
+
+static int __init adder875_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+ return of_flat_dt_is_compatible(root, "analogue-and-micro,adder875");
+}
+
+static __initdata const struct of_device_id __initdata of_bus_ids[] = {
+ { .name = "soc", },
+ { .name = "cpm", },
+ { .name = "localbus", },
+ {},
+};
+
+static int __init declare_of_platform_devices(void)
+{
+ of_platform_bus_probe(NULL, of_bus_ids, NULL);
+ return 0;
+}
+machine_device_initcall(adder875, declare_of_platform_devices);
+
+define_machine(adder875) {
+ .name = "Adder MPC875",
+ .probe = adder875_probe,
+ .setup_arch = adder875_setup,
+ .init_IRQ = m8xx_pic_init,
+ .get_irq = mpc8xx_get_irq,
+ .restart = mpc8xx_restart,
+ .calibrate_decr = generic_calibrate_decr,
+ .set_rtc_time = mpc8xx_set_rtc_time,
+ .get_rtc_time = mpc8xx_get_rtc_time,
+ .progress = udbg_progress,
+};
--
1.5.3.8
^ permalink raw reply related
* Re: [PATCH 1/3] 8xx: Analogue & Micro Adder875 board support.
From: Bryan O'Donoghue @ 2008-01-15 23:25 UTC (permalink / raw)
To: Scott Wood; +Cc: linuxppc-dev
In-Reply-To: <478BE6F2.4020207@freescale.com>
Greetings Scott.
I've tried both of the procedures you've outlined on the Adder875 with
the patches supplied against the paulus git tree to no avail.
Pass #1 :
Doing it safe with cuImage.8xx
Build system : Debian lenny, ELDK 4.1 uClibc
Kernel : Linux-2.6.24-rc6-g4f43143f-dirty - about two days old
Bootloader : U-Boot 1.3.1-g5c740711-dirty (Jan 15 2008 - 21:50)
#define CONFIG_OF_LIBFDT 1
#undef CONFIG_OF_FLAT_TREE
- So that U-Boot will understand the three parameter bootm.
dtc : DTC 1.1.0-rc1
I do
1. source /opt/eldk/eldk_init ppc_8xx
2. export ARCH=powerpc
3. cd linux-2.6-paulus
4. git branch adder875-patchset master
5. git checkout adder875-patchset
6. cat ../adder875_patches/adder875.patch | patch -p1
The patch applies almost perfectly - except for a minor conflict in
arch/powerpc/boot/Makefile - where I add redboot-8xx.c right after
cuboot-rainer.c manually.
7. make distclean && mrproper && clean
8. make adder875-uboot_defconfig
9. make zImage
That runs just fine - and just to prove to you I haven't done anything
funny here the last few lines of output are
HOSTLD arch/powerpc/boot/dtc
WRAP arch/powerpc/boot/cuImage.8xx
DTC: dts->dtb on file
"/home/deckard/Development/linux/linux-2.6-paulus/arch/powerpc/boot/dts/adder875-uboot.dts"
Image Name: Linux-2.6.24-rc6-g4f43143f-dirty
Created: Tue Jan 15 23:02:52 2008
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1032266 Bytes = 1008.07 kB = 0.98 MB
Load Address: 0x00400000
Entry Point: 0x00400554
WRAP arch/powerpc/boot/zImage.redboot-8xx
DTC: dts->dtb on file
"/home/deckard/Development/linux/linux-2.6-paulus/arch/powerpc/boot/dts/adder875-uboot.dts"
cp arch/powerpc/boot/ucImage.8xx /tftpboot
The U-Boot output is :
=> tftpboot 0x400000 cuImage.8xx
Using FEC ETHERNET device
TFTP from server 192.168.0.101; our IP address is 192.168.0.202
Filename 'cuImage.8xx'.
Load address: 0x400000
Loading:
#################################################################
#################################################################
#################################################################
#######
done
Bytes transferred = 1032330 (fc08a hex)
=> bootm 0x400000
## Booting image at 00400000 ...
Image Name: Linux-2.6.24-rc6-g4f43143f-dirty
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1032266 Bytes = 1008.1 kB
Load Address: 00400000
Entry Point: 00400554
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
I haven't as yet tried to single step through the bootup process - but,
just to say that assuming the above procedure isn't _too_ far wrong -
the stuff posted to the list agains the tree you've recommended doesn't
seem to work..
If you can point out a flaw in my usage of it - that'd help alot. I have
some code I'd love to be able to use with the Adder875+powerpc layer -
which is why I'm interested in this patchset...
Pass #2 :
Replace step 9 with.
9. make uImage
10 dtc -o ../adder875-uboot.dtb -O dtb
arch/powerpc/boot/dts/adder875-uboot.dts
cp arch/powerpc/boot/uImage /tftpboot
cp ../adder875-uboot.dtb /tftpboot
Finally in u-boot
=> tftpboot 0x400000 uImage
Using FEC ETHERNET device
TFTP from server 192.168.0.101; our IP address is 192.168.0.202
Filename 'uImage'.
Load address: 0x400000
Loading:
#################################################################
#################################################################
#################################################################
###
done
Bytes transferred = 1009496 (f6758 hex)
=> tftpboot 0x500000 adder875-uboot.dtb
Using FEC ETHERNET device
TFTP from server 192.168.0.101; our IP address is 192.168.0.202
Filename 'adder875-uboot.dtb'.
Load address: 0x500000
Loading: #
done
Bytes transferred = 3147 (c4b hex)
=> bootm 0x400000 - 0x500000
## Booting image at 00400000 ...
Image Name: Linux-2.6.24-rc6-g4f43143f-dirty
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1009432 Bytes = 985.8 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Booting using the fdt at 0x500000
Aside from the u-boot modification of including
#define CONFIG_OF_LIBFDT 1
The rest is a pristine version of Yuli Barchoen's original U-Boot Adder
stuff.
The uImage + dtb seems to get a good bit further in that it seems to get
stuck somewhere inside of some trampoline code in time.c
(gdb) bt
#0 0xc000ee30 in __div64_32 ()
#1 0xc01d71f4 in time_init () at arch/powerpc/kernel/time.c:940
I might have a go at some proper debugging tomorrow after work.
If you have any suggestions as to what's going wrong or what I've not
done right I'd appreciate the help.
Best Regards,
BOD
^ permalink raw reply
* Re: [PATCH] change where the kernel loads
From: Scott Wood @ 2008-01-15 21:09 UTC (permalink / raw)
To: mjw; +Cc: linuxppc-dev
In-Reply-To: <478D2038.4090205@linux.vnet.ibm.com>
Mike Wolf wrote:
> When netbooting a kernel with an initrd or initramfs that makes
> the image larger than 8 meg the firmware will kick out the kernel
> and go to the second boot device. However when the mkzimage
> script is used to create the image instead of 'make zImage' then
> the kernel/initrd will netboot. So this patch changes boot/zImage.lds
> to load the kernel at the same location that the mkzimage would set.
>
> This has been boot tested on POWER5, POWER5+, blades and POWER6
> systems successfully.
This will fail on any platform without a vmlinux_alloc(), as there will
be insufficient room for the kernel at address zero.
-Scott
^ permalink raw reply
* [PATCH] change where the kernel loads
From: Mike Wolf @ 2008-01-15 21:06 UTC (permalink / raw)
To: linuxppc-dev
When netbooting a kernel with an initrd or initramfs that makes
the image larger than 8 meg the firmware will kick out the kernel
and go to the second boot device. However when the mkzimage
script is used to create the image instead of 'make zImage' then
the kernel/initrd will netboot. So this patch changes boot/zImage.lds
to load the kernel at the same location that the mkzimage would set.
This has been boot tested on POWER5, POWER5+, blades and POWER6
systems successfully.
signed off by: Mike Wolf (mjw@us.ibm.com)
------
--- linux-2.6.16.46-0.12.orig/arch/powerpc/boot/zImage.lds 2008-01-07 14:51:05.000000000 -0600
+++ linux-2.6.16.46-0.12/arch/powerpc/boot/zImage.lds 2008-01-07 14:31:14.000000000 -0600
@@ -2,7 +2,7 @@
ENTRY(_zimage_start)
SECTIONS
{
- . = (4*1024*1024);
+ . = (64*1024);
_start = .;
.text :
{
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox