* RE: x86/non-x86: percpu, node ids, apic ids x86.git fixup
From: Luck, Tony @ 2008-01-31 18:34 UTC (permalink / raw)
To: Ingo Molnar
Cc: sparclinux, linux-ia64, Linux Kernel Development, Mike Travis,
Linux/PPC Development, Geert Uytterhoeven, Thomas Gleixner,
Linus Torvalds
In-Reply-To: <20080131090642.GA5688@elte.hu>
> hm, as far as i could check, on ia64 UP the .percpu section link=20
> difference was the only ia64 difference i could find out of those=20
> changes. Could you try to copy a 2.6.24 include/asm-generic/percpu.h,=20
> include/asm-ia64.h and include/linux/percpu.h into your current tree,=20
> and see whether that boots? If yes, then it's the percpu changes. The=20
> patch below does this ontop of very latest -git - and it builds fine=20
> with your UP config with a crosscompiler.
Applied that patch and UP kernel built ok, and then crashed in the
same place with the memset() to a user-looking address from =
kmem_cache_alloc()
So the percpu changes are innocent ... something else since 2.6.24 is
to blame. Only 5749 commits :-) I'll start bisecting.
-Tony
^ permalink raw reply
* Re: [RFC] [POWERPC] bootwrapper: build multiple cuImages
From: Grant Likely @ 2008-01-31 17:22 UTC (permalink / raw)
To: Scott Wood; +Cc: linuxppc-dev
In-Reply-To: <20080131160042.GA24370@ld0162-tx32.am.freescale.net>
On 1/31/08, Scott Wood <scottwood@freescale.com> wrote:
> On Wed, Jan 30, 2008 at 07:40:28PM -0700, Grant Likely wrote:
> > mpc866ads, mpc885ads and ep88xc are oddities in that they build
> > zImages with embedded device tree blobs.
>
> What about ep8248e? And the mpc8xxads boards use cuImage, not zImage.
Oops, those are just mistakes. I can fix them
>
> > One option would be to add two new targets: zImage.dtb.% and
> > zImage.initrd.dtb.%, but I'm not sure if it is a good idea.
>
> I'd much prefer that over having several lines per board in the makefile.
Okay, I can change that.
Another option is to modify the wrapper to specifically look for
targets which need the dtb. At the moment, that list includes ps3,
ep8248e, mpc885ads and ep88xc. All four could be using a common build
target.
Cheers,
g.
--
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
^ permalink raw reply
* [PATCH] adder875, ep88xc: fix to match recent 8xx cleanups.
From: Scott Wood @ 2008-01-31 17:36 UTC (permalink / raw)
To: galak; +Cc: linuxppc-dev
asm/commproc.h was renamed to asm/cpm1.h
sysdev/commproc.h was renamed to platforms/8xx/mpc8xx.h
m8xx_pic_init was renamed to mpc8xx_pics_init
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
arch/powerpc/platforms/8xx/adder875.c | 6 +++---
arch/powerpc/platforms/8xx/ep88xc.c | 1 -
2 files changed, 3 insertions(+), 4 deletions(-)
diff --git a/arch/powerpc/platforms/8xx/adder875.c b/arch/powerpc/platforms/8xx/adder875.c
index c6bc078..82363e9 100644
--- a/arch/powerpc/platforms/8xx/adder875.c
+++ b/arch/powerpc/platforms/8xx/adder875.c
@@ -15,12 +15,12 @@
#include <asm/time.h>
#include <asm/machdep.h>
-#include <asm/commproc.h>
+#include <asm/cpm1.h>
#include <asm/fs_pd.h>
#include <asm/udbg.h>
#include <asm/prom.h>
-#include <sysdev/commproc.h>
+#include "mpc8xx.h"
struct cpm_pin {
int port, pin, flags;
@@ -108,7 +108,7 @@ define_machine(adder875) {
.name = "Adder MPC875",
.probe = adder875_probe,
.setup_arch = adder875_setup,
- .init_IRQ = m8xx_pic_init,
+ .init_IRQ = mpc8xx_pics_init,
.get_irq = mpc8xx_get_irq,
.restart = mpc8xx_restart,
.calibrate_decr = generic_calibrate_decr,
diff --git a/arch/powerpc/platforms/8xx/ep88xc.c b/arch/powerpc/platforms/8xx/ep88xc.c
index a8dffa0..7d9ac60 100644
--- a/arch/powerpc/platforms/8xx/ep88xc.c
+++ b/arch/powerpc/platforms/8xx/ep88xc.c
@@ -15,7 +15,6 @@
#include <asm/machdep.h>
#include <asm/io.h>
#include <asm/udbg.h>
-#include <asm/commproc.h>
#include <asm/cpm1.h>
#include "mpc8xx.h"
--
1.5.3.8
^ permalink raw reply related
* Re: [PATCH 1/2] Add RapidIO node into MPC8641HPCN dts file
From: Jon Loeliger @ 2008-01-31 17:00 UTC (permalink / raw)
To: Zhang Wei; +Cc: linuxppc-dev
In-Reply-To: <12017656032841-git-send-email-wei.zhang@freescale.com>
Zhang Wei wrote:
> Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
> ---
> arch/powerpc/boot/dts/mpc8641_hpcn.dts | 13 +++++++++++++
> 1 files changed, 13 insertions(+), 0 deletions(-)
>
> diff --git a/arch/powerpc/boot/dts/mpc8641_hpcn.dts b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
> index 556a9ca..1a0fce5 100644
> --- a/arch/powerpc/boot/dts/mpc8641_hpcn.dts
> +++ b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
> @@ -499,4 +500,16 @@
> 0 00100000>;
> };
> };
> +
> + rapidio0: rapidio@f80c0000 {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + compatible = "fsl,rapidio-delta";
> + reg = <f80c0000 20000>;
> + ranges = <0 0 c0000000 0 20000000>;
> + interrupt-parent = <&mpic>;
> + /* err_irq bell_outb_irq bell_inb_irq
> + msg1_tx_irq msg1_rx_irq msg2_tx_irq msg2_rx_irq */
> + interrupts = <30 2 31 2 32 2 35 2 36 2 37 2 38 2>;
> + };
> };
Have updates to the booting-without-of.txt file for
been made or proposed for the RapidIO node definition?
jdl
^ permalink raw reply
* RE: Kernel oops while duming user core.
From: Rune Torgersen @ 2008-01-31 17:40 UTC (permalink / raw)
To: Nathan Lynch; +Cc: linuxppc-dev
In-Reply-To: <DCEAAC0833DD314AB0B58112AD99B93B03EE46B8@ismail.innsys.innovsys.com>
Rune Torgersen wrote:
> I was going to test HEAD of powerpc.git to see if it is still there.
Still there. Also used GDB on the vmlinux image to get source and
dissasembly of the ooops:
Unable to handle kernel paging request for data at address 0x48024000
Faulting instruction address: 0xc000f0a0
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT Innovative Systems ApMax
Modules linked in: drv_wd(P) drv_scc devcom drv_pcir tipc drv_ss7
drv_auxcpu drv_leds(P) drv_ethsw proc_sysinfo(P) i2c_8266(P)
NIP: c000f0a0 LR: c0011fec CTR: 00000080
REGS: eebe9b70 TRAP: 0300 Tainted: P (2.6.24-test)
MSR: 00009032 <EE,ME,IR,DR> CR: 24004442 XER: 00000000
DAR: 48024000, DSISR: 20000000
TASK =3D eeba9780[2554] 'armd_crash' THREAD: eebe8000
GPR00: eea44d00 eebe9c20 eeba9780 48024000 00000080 37a56181 48024000
00000000
GPR08: 37a56181 eea44d00 00000000 c2000000 44004422 10100f38 ef336600
bfffffff
GPR16: eeff0300 00000030 eea44d00 00000000 eebe9cdc 00000011 eebe9cd8
eebca480
GPR24: eea44d00 37a56181 48024000 eebad580 eebad580 37a56181 48024000
c26f4ac0
NIP [c000f0a0] __flush_dcache_icache+0x14/0x40
LR [c0011fec] update_mmu_cache+0x74/0x114
Call Trace:
[eebe9c20] [eebe8000] 0xeebe8000 (unreliable)
[eebe9c40] [c005cfd0] handle_mm_fault+0x630/0xbc0
[eebe9c80] [c005d954] get_user_pages+0x3f4/0x4fc
[eebe9cd0] [c00aa730] elf_core_dump+0x9a4/0xc5c
[eebe9d60] [c0077954] do_coredump+0x6e0/0x748
[eebe9e50] [c002a520] get_signal_to_deliver+0x40c/0x45c
[eebe9e80] [c0008cec] do_signal+0x50/0x294
[eebe9f40] [c000fc9c] do_user_signal+0x74/0xc4
--- Exception: 300 at 0x10044efc
LR =3D 0x10044ec0
Instruction dump:
4d820020 7c8903a6 7c001bac 38630020 4200fff8 7c0004ac 4e800020 60000000
54630026 38800080 7c8903a6 7c661b78 <7c00186c> 38630020 4200fff8
7c0004ac
---[ end trace 37755b0fb9e79677 ]---
note: armd_crash[2554] exited with preempt_count 2
backtrace using gdb on vmlinux image:
0xc00aa730 is in elf_core_dump (fs/binfmt_elf.c:1762).
1757
1758 for (addr =3D vma->vm_start; addr < end; addr =
+=3D
PAGE_SIZE) {
1759 struct page *page;
1760 struct vm_area_struct *vma;
1761
1762 if (get_user_pages(current, current->mm,
addr, 1, 0, 1,
1763 &page, &vma) =
<=3D
0) {
1764 DUMP_SEEK(PAGE_SIZE);
1765 } else {
1766 if (page =3D=3D ZERO_PAGE(0)) {
(gdb) list *0xc005d954
0xc005d954 is in get_user_pages (mm/memory.c:1072).
1067 cond_resched();
1068 while (!(page =3D follow_page(vma, =
start,
foll_flags))) {
1069 int ret;
1070 ret =3D handle_mm_fault(mm, vma,
start,
1071 foll_flags &
FOLL_WRITE);
1072 if (ret & VM_FAULT_ERROR) {
1073 if (ret & VM_FAULT_OOM)
1074 return i ? i :
-ENOMEM;
1075 else if (ret &
VM_FAULT_SIGBUS)
1076 return i ? i :
-EFAULT;
(gdb) list *0xc005cfd0
0xc005cfd0 is in handle_mm_fault (include/asm/thread_info.h:99).
94 {
95 register unsigned long sp asm("r1");
96
97 /* gcc4, at least, is smart enough to turn this into a
single
98 * rlwinm for ppc32 and clrrdi for ppc64 */
99 return (struct thread_info *)(sp & ~(THREAD_SIZE-1));
100 }
101
102 #endif /* __ASSEMBLY__ */
103
(gdb) =20
(gdb) list *0xc0011fec
0xc0011fec is in update_mmu_cache (arch/powerpc/mm/mem.c:489).
484 _tlbie(address, 0 /* 8xx doesn't care about PID
*/);
485 #endif
486 if (!PageReserved(page)
487 && !test_bit(PG_arch_1, &page->flags)) {
488 if (vma->vm_mm =3D=3D =
current->active_mm) {
489 __flush_dcache_icache((void *)
address);
490 } else
491 flush_dcache_icache_page(page);
492 set_bit(PG_arch_1, &page->flags);
493 }
(gdb) list *0xc000f0a0
No source file for address 0xc000f0a0.
(gdb) disassemble 0xc000f0a0
Dump of assembler code for function __flush_dcache_icache:
0xc000f08c <__flush_dcache_icache+0>: dec %esi
0xc000f08d <__flush_dcache_icache+1>: addb $0x20,(%eax)
0xc000f090 <__flush_dcache_icache+4>: push %esp
0xc000f091 <__flush_dcache_icache+5>: arpl %ax,(%eax)
0xc000f093 <__flush_dcache_icache+7>: cmp %al,%es:0x897c8000(%eax)
0xc000f09a <__flush_dcache_icache+14>: add 0x781b667c(%esi),%esp
0xc000f0a0 <__flush_dcache_icache+20>: jl 0xc000f0a2
<__flush_dcache_icache+22>
0xc000f0a2 <__flush_dcache_icache+22>: sbb %ch,0x63(%eax,%edi,1)
0xc000f0a6 <__flush_dcache_icache+26>: add %ah,(%eax)
0xc000f0a8 <__flush_dcache_icache+28>: inc %edx
0xc000f0a9 <__flush_dcache_icache+29>: add %bh,%bh
0xc000f0ab <__flush_dcache_icache+31>: clc
0xc000f0ac <__flush_dcache_icache+32>: jl 0xc000f0ae
<__flush_dcache_icache+34>
0xc000f0ae <__flush_dcache_icache+34>: add $0xac,%al
0xc000f0b0 <__flush_dcache_icache+36>: jl 0xc000f03b
<flush_dcache_range+15>
0xc000f0b2 <__flush_dcache_icache+38>: add 0xac37007c(%esi),%esp
0xc000f0b8 <__flush_dcache_icache+44>: cmp %al,%dh
0xc000f0ba <__flush_dcache_icache+46>: add %ah,(%eax)
0xc000f0bc <__flush_dcache_icache+48>: inc %edx
0xc000f0bd <__flush_dcache_icache+49>: add %bh,%bh
0xc000f0bf <__flush_dcache_icache+51>: clc
0xc000f0c0 <__flush_dcache_icache+52>: jl 0xc000f0c2
<__flush_dcache_icache+54>
0xc000f0c2 <__flush_dcache_icache+54>: add $0xac,%al
0xc000f0c4 <__flush_dcache_icache+56>: dec %esp
0xc000f0c5 <__flush_dcache_icache+57>: add %al,(%ecx)
0xc000f0c7 <__flush_dcache_icache+59>: sub $0x4e,%al
0xc000f0c9 <__flush_dcache_icache+61>: addb $0x20,(%eax)
End of assembler dump.
(gdb) =20
^ permalink raw reply
* Re: Configuring Freecale ucc_geth without a PHY
From: Jon Loeliger @ 2008-01-31 16:51 UTC (permalink / raw)
To: Steven Hein; +Cc: linuxppc-embedded
In-Reply-To: <47A1CF43.8070107@sgi.com>
Steven Hein wrote:
> Is there a document anywhere that describes how to submit
> patches for the powerpc kernel? Or do I just create the patch
> (I'm learning about git right now...) again the paulus/powerpc.git
> tree, and send it to this list?
>
Correct. Don't just lean toward git, actually use it.
And paulus/powerpc.git is the right basis.
Send it to the linuxppc-dev@ozlabs.org list, not here.
jdl
^ permalink raw reply
* Re: [PATCH] [POWERPC] Set dma_data correctly for direct_ops on pasemi
From: Olof Johansson @ 2008-01-31 16:18 UTC (permalink / raw)
To: Michael Ellerman; +Cc: torvalds, Paul Mackerras, linuxppc-dev
In-Reply-To: <1201783096.4147.3.camel@concordia>
On Thu, Jan 31, 2008 at 11:38:16PM +1100, Michael Ellerman wrote:
> On Thu, 2008-01-31 at 00:41 -0600, Olof Johansson wrote:
> > More late-caught fallout from the mainline merge. The patch:
> >
> > [POWERPC] Use archdata.dma_data in dma_direct_ops and add the offset
> >
> > "Now that all platforms using dma_direct_offset setup the
> > archdata.dma_data correctly, ..."
> >
> > Nope -- the pasemi iommu setup code that disables translation on the
> > DMA pci device didn't set dma_data correctly.
> >
> > The below patch is needed, please merge as soon as practical. Thanks!
>
> Sorry about that.
>
> I'm confused though, didn't your device come from alloc_pci_dev() which
> kzalloc()s the pci_dev which contains the archdata which contains the
> dma_data, ie. dma_data will already be 0?
Yeah, I don't see how my patch could work (but it did), since the code
falls through and overwrites dma_data with the pointer to the table,
just as before. Weird, I did test it last night. See new patch.
-Olof
^ permalink raw reply
* [PATCH v2] [POWERPC] Set dma_data correctly for direct_ops on pasemi
From: Olof Johansson @ 2008-01-31 16:25 UTC (permalink / raw)
To: Paul Mackerras; +Cc: linuxppc-dev, torvalds
In-Reply-To: <20080131064130.GA32344@lixom.net>
More fallout from the merge:
[POWERPC] Use archdata.dma_data in dma_direct_ops and add the offset
"Now that all platforms using dma_direct_offset setup the
archdata.dma_data correctly, ..."
Nope -- the pasemi iommu setup code that disables translation on the DMA
pci device still set dma_data to point at the table. The below patch is
needed, please merge asap.
Signed-off-by: Olof Johansson <olof@lixom.net>
diff --git a/arch/powerpc/platforms/pasemi/iommu.c b/arch/powerpc/platforms/pasemi/iommu.c
index 9916a0f..5803f11 100644
--- a/arch/powerpc/platforms/pasemi/iommu.c
+++ b/arch/powerpc/platforms/pasemi/iommu.c
@@ -182,8 +182,10 @@ static void pci_dma_dev_setup_pasemi(struct pci_dev *dev)
* CONFIG_PPC_PASEMI_IOMMU_DMA_FORCE at build time.
*/
if (dev->vendor == 0x1959 && dev->device == 0xa007 &&
- !firmware_has_feature(FW_FEATURE_LPAR))
+ !firmware_has_feature(FW_FEATURE_LPAR)) {
dev->dev.archdata.dma_ops = &dma_direct_ops;
+ return;
+ }
#endif
dev->dev.archdata.dma_data = &iommu_table_iobmap;
^ permalink raw reply related
* RE: Kernel oops while duming user core.
From: Rune Torgersen @ 2008-01-31 16:26 UTC (permalink / raw)
To: Nathan Lynch; +Cc: linuxppc-dev
In-Reply-To: <20080131161527.GT14201@localdomain>
Nathan Lynch wrote:
> Hmm, this is the second report of 2.6.24 crashing in
> __flush_dcache_icache during a core dump; see:
> http://ozlabs.org/pipermail/linuxppc-dev/2007-December/048662.html
>=20
> Is this easily recreatable?
Yes. I have a binary that will do this every time it is started (on this
particular system),=20
only takes about 10 seconds before it dumps.
I was going to test HEAD of powerpc.git to see if it is still there.
I cannot test any earlier versions as our board port was done on 2.6.24.
Our older kernel port is 2.6.18 on arch/ppc, and it works just fine.
One potential clue:
> Unable to handle kernel paging request for data at address 0x48024000
this adddress is beyond our physical memory. We have 1GB of mem=20
(CONFIG_HIGH_MEM enabled) so 0x3fff_ffff is the last valid address.
0x4000_0000 to 0x7fff_ffff are unused, 0x8000_0000 to 0x9fff_ffff is
used by PCI.
^ permalink raw reply
* Re: [RFC] [POWERPC] bootwrapper: build multiple cuImages
From: Scott Wood @ 2008-01-31 16:00 UTC (permalink / raw)
To: Grant Likely; +Cc: linuxppc-dev
In-Reply-To: <fa686aa40801301840k3d9a9ba2n251d2cdb9e659748@mail.gmail.com>
On Wed, Jan 30, 2008 at 07:40:28PM -0700, Grant Likely wrote:
> mpc866ads, mpc885ads and ep88xc are oddities in that they build
> zImages with embedded device tree blobs.
What about ep8248e? And the mpc8xxads boards use cuImage, not zImage.
> One option would be to add two new targets: zImage.dtb.% and
> zImage.initrd.dtb.%, but I'm not sure if it is a good idea.
I'd much prefer that over having several lines per board in the makefile.
-Scott
^ permalink raw reply
* build fails for adder875 for new pulls of powerpc.git
From: Rognlien Dag Kristian @ 2008-01-31 14:18 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <mailman.1812.1201784040.6908.linuxppc-dev@ozlabs.org>
[-- Attachment #1: Type: text/plain, Size: 186 bytes --]
The latest commits to powerpc.git removes commproc.h files used by arch/powerpc/platforms/8xx/adder875.c
The kernel fails to build for the adder configs.
Regards,
Dag Rognlien
[-- Attachment #2: winmail.dat --]
[-- Type: application/ms-tnef, Size: 2642 bytes --]
^ permalink raw reply
* [PATCH v7] [POWERPC] Add LED driver for Promess Motion-PRO board.
From: Marian Balakowicz @ 2008-01-31 13:49 UTC (permalink / raw)
To: linuxppc-dev
Add support for two Motion-PRO board custom LEDs:
- motionpro-statusled
- motionpro-readyled
Signed-off-by: Jan Wrobel <wrr@semihalf.com>
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
---
Update since v6:
- fix error handling for null label proper
drivers/leds/Kconfig | 7 +
drivers/leds/Makefile | 3
drivers/leds/leds-motionpro.c | 250 +++++++++++++++++++++++++++++++++++++++++
include/asm-powerpc/mpc52xx.h | 5 +
4 files changed, 264 insertions(+), 1 deletions(-)
create mode 100644 drivers/leds/leds-motionpro.c
diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index ec568fa..1567ed6 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -55,6 +55,13 @@ config LEDS_TOSA
This option enables support for the LEDs on Sharp Zaurus
SL-6000 series.
+config LEDS_MOTIONPRO
+ tristate "Motion-PRO LEDs Support"
+ depends on LEDS_CLASS && PPC_MPC5200
+ help
+ This option enables support for status and ready LEDs connected
+ to GPIO lines on Motion-PRO board.
+
config LEDS_S3C24XX
tristate "LED Support for Samsung S3C24XX GPIO LEDs"
depends on LEDS_CLASS && ARCH_S3C2410
diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
index a60de1b..a56d399 100644
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -18,7 +18,8 @@ obj-$(CONFIG_LEDS_H1940) += leds-h1940.o
obj-$(CONFIG_LEDS_COBALT_QUBE) += leds-cobalt-qube.o
obj-$(CONFIG_LEDS_COBALT_RAQ) += leds-cobalt-raq.o
obj-$(CONFIG_LEDS_GPIO) += leds-gpio.o
-obj-$(CONFIG_LEDS_CM_X270) += leds-cm-x270.o
+obj-$(CONFIG_LEDS_CM_X270) += leds-cm-x270.o
+obj-$(CONFIG_LEDS_MOTIONPRO) += leds-motionpro.o
# LED Triggers
obj-$(CONFIG_LEDS_TRIGGER_TIMER) += ledtrig-timer.o
diff --git a/drivers/leds/leds-motionpro.c b/drivers/leds/leds-motionpro.c
new file mode 100644
index 0000000..b8dfa8a
--- /dev/null
+++ b/drivers/leds/leds-motionpro.c
@@ -0,0 +1,250 @@
+/*
+ * LEDs driver for the Motion-PRO board.
+ *
+ * Copyright (C) 2007 Semihalf
+ * Jan Wrobel <wrr@semihalf.com>
+ * Marian Balakowicz <m8@semihalf.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc., 51
+ * Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ *
+ *
+ * Decription:
+ * This driver enables control over Motion-PRO status and ready LEDs through
+ * sysfs. LEDs can be controlled by writing to sysfs files:
+ * class/leds/<led-name>/(brightness|delay_off|delay_on).
+ * See Documentation/leds-class.txt for more details.
+ * <led-name> is the set to the value of 'label' property of the
+ * corresponding GPT node.
+ *
+ * Before user issues first control command via sysfs, LED blinking is
+ * controlled by the kernel ('blink-delay' property of the GPT node
+ * in the device tree blob).
+ *
+ */
+
+#define DEBUG
+
+#include <linux/module.h>
+#include <linux/leds.h>
+#include <linux/of_platform.h>
+#include <asm/mpc52xx.h>
+
+/* LED control bits */
+#define LED_ON MPC52xx_GPT_OUTPUT_1
+
+/* LED mode */
+#define LED_MODE_KERNEL 1
+#define LED_MODE_USER 2
+
+struct motionpro_led {
+ spinlock_t led_lock; /* Protects the LED data */
+ struct mpc52xx_gpt __iomem *gpt;/* LED registers */
+ struct timer_list blink_timer; /* Used if blink_delay is nonzero */
+ unsigned int blink_delay; /* [ms], if set to 0 blinking is off */
+ unsigned int mode; /* kernel/user */
+ struct led_classdev mpled_cdev; /* LED class */
+};
+
+/*
+ * Timer event - blinks LED before user takes control over it
+ * with the first access via sysfs.
+ */
+static void mpled_timer_toggle(unsigned long data)
+{
+ struct motionpro_led *mpled = (struct motionpro_led *)data;
+
+ spin_lock_bh(&mpled->led_lock);
+ if (mpled->mode == LED_MODE_KERNEL) {
+ u32 val = in_be32(&mpled->gpt->mode);
+ val ^= LED_ON;
+ out_be32(&mpled->gpt->mode, val);
+
+ mod_timer(&mpled->blink_timer,
+ jiffies + msecs_to_jiffies(mpled->blink_delay));
+ }
+ spin_unlock_bh(&mpled->led_lock);
+}
+
+/*
+ * Turn on/off led according to user settings in sysfs.
+ * First call to this function disables kernel blinking.
+ */
+static void mpled_set(struct led_classdev *led_cdev,
+ enum led_brightness brightness)
+{
+ struct motionpro_led *mpled;
+ int old_mode;
+ u32 val;
+
+ mpled = container_of(led_cdev, struct motionpro_led, mpled_cdev);
+
+ spin_lock_bh(&mpled->led_lock);
+ /* disable kernel controll */
+ old_mode = mpled->mode;
+ if (old_mode == LED_MODE_KERNEL)
+ mpled->mode = LED_MODE_USER;
+
+ val = in_be32(&mpled->gpt->mode);
+ if (brightness)
+ val |= LED_ON;
+ else
+ val &= ~LED_ON;
+ out_be32(&mpled->gpt->mode, val);
+ spin_unlock_bh(&mpled->led_lock);
+
+ /* delete kernel mode blink timer, not needed anymore */
+ if ((old_mode == LED_MODE_KERNEL) && mpled->blink_delay)
+ del_timer(&mpled->blink_timer);
+}
+
+static void mpled_init_led(void __iomem *gpt_mode)
+{
+ u32 val = in_be32(gpt_mode);
+ val |= MPC52xx_GPT_ENABLE_OUTPUT;
+ val &= ~LED_ON;
+ out_be32(gpt_mode, val);
+}
+
+static int __devinit mpled_probe(struct of_device *op,
+ const struct of_device_id *match)
+{
+ struct motionpro_led *mpled;
+ const unsigned int *of_blink_delay;
+ const char *label;
+ int err;
+
+ dev_dbg(&op->dev, "mpled_probe: node=%s (op=%p, match=%p)\n",
+ op->node->name, op, match);
+
+ mpled = kzalloc(sizeof(*mpled), GFP_KERNEL);
+ if (!mpled)
+ return -ENOMEM;
+
+ mpled->gpt = of_iomap(op->node, 0);
+ if (!mpled->gpt) {
+ printk(KERN_ERR __FILE__ ": "
+ "Error mapping GPT registers for LED %s\n",
+ op->node->full_name);
+ err = -EIO;
+ goto err_free;
+ }
+
+ /* initialize GPT for LED use */
+ mpled_init_led(&mpled->gpt->mode);
+
+ spin_lock_init(&mpled->led_lock);
+ mpled->mode = LED_MODE_KERNEL;
+
+ /* get LED label, used to register led classdev */
+ label = of_get_property(op->node, "label", NULL);
+ if (label == NULL) {
+ printk(KERN_ERR __FILE__ ": "
+ "No label property provided for LED %s\n",
+ op->node->full_name);
+ err = -EINVAL;
+ goto err;
+ }
+ dev_dbg(&op->dev, "mpled_probe: label = '%s'\n", label);
+
+ /* get 'blink-delay' property if present */
+ of_blink_delay = of_get_property(op->node, "blink-delay", NULL);
+ mpled->blink_delay = of_blink_delay ? *of_blink_delay : 0;
+ dev_dbg(&op->dev, "mpled_probe: blink_delay = %d msec\n",
+ mpled->blink_delay);
+
+ /* initialize kernel blink_timer if blink_delay was provided */
+ if (mpled->blink_delay) {
+ init_timer(&mpled->blink_timer);
+ mpled->blink_timer.function = mpled_timer_toggle;
+ mpled->blink_timer.data = (unsigned long)mpled;
+
+ mod_timer(&mpled->blink_timer,
+ jiffies + msecs_to_jiffies(mpled->blink_delay));
+ }
+
+ /* register LED classdev */
+ mpled->mpled_cdev.name = label;
+ mpled->mpled_cdev.brightness_set = mpled_set;
+ mpled->mpled_cdev.default_trigger = "timer";
+
+ err = led_classdev_register(NULL, &mpled->mpled_cdev);
+ if (err) {
+ printk(KERN_ERR __FILE__ ": "
+ "Error registering class device for LED %s\n",
+ op->node->full_name);
+ goto err;
+ }
+
+ dev_set_drvdata(&op->dev, mpled);
+ return 0;
+
+err:
+ if (mpled->blink_delay)
+ del_timer(&mpled->blink_timer);
+ iounmap(mpled->gpt);
+err_free:
+ kfree(mpled);
+
+ return err;
+}
+
+static int mpled_remove(struct of_device *op)
+{
+ struct motionpro_led *mpled = dev_get_drvdata(&op->dev);
+
+ dev_dbg(&op->dev, "mpled_remove: (%p)\n", op);
+
+ if (mpled->blink_delay && (mpled->mode == LED_MODE_KERNEL))
+ del_timer(&mpled->blink_timer);
+
+ led_classdev_unregister(&mpled->mpled_cdev);
+
+ iounmap(mpled->gpt);
+ kfree(mpled);
+
+ return 0;
+}
+
+static const struct of_device_id mpled_match[] = {
+ { .compatible = "promess,motionpro-led", },
+ {},
+};
+
+static struct of_platform_driver mpled_driver = {
+ .match_table = mpled_match,
+ .probe = mpled_probe,
+ .remove = mpled_remove,
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "leds-motionpro",
+ },
+};
+
+static int __init mpled_init(void)
+{
+ return of_register_platform_driver(&mpled_driver);
+}
+
+static void __exit mpled_exit(void)
+{
+ of_unregister_platform_driver(&mpled_driver);
+}
+
+module_init(mpled_init);
+module_exit(mpled_exit);
+
+MODULE_LICENSE("GPL")
+MODULE_DESCRIPTION("Motion-PRO LED driver");
+MODULE_AUTHOR("Jan Wrobel <wrr@semihalf.com>");
+MODULE_AUTHOR("Marian Balakowicz <m8@semihalf.com>");
diff --git a/include/asm-powerpc/mpc52xx.h b/include/asm-powerpc/mpc52xx.h
index 1c48c6d..de869ee 100644
--- a/include/asm-powerpc/mpc52xx.h
+++ b/include/asm-powerpc/mpc52xx.h
@@ -147,6 +147,11 @@ struct mpc52xx_gpio {
#define MPC52xx_GPIO_PSC_CONFIG_UART_WITH_CD 5
#define MPC52xx_GPIO_PCI_DIS (1<<15)
+/* Enables GPT register to operate as simple GPIO output register */
+#define MPC52xx_GPT_ENABLE_OUTPUT 0x00000024
+/* Puts 1 on GPT output pin */
+#define MPC52xx_GPT_OUTPUT_1 0x00000010
+
/* GPIO with WakeUp*/
struct mpc52xx_gpio_wkup {
u8 wkup_gpioe; /* GPIO_WKUP + 0x00 */
^ permalink raw reply related
* Kernel oops while duming user core.
From: Rune Torgersen @ 2008-01-31 13:45 UTC (permalink / raw)
To: linuxppc-dev
Hi
I get the following kernel core while a user program I have is dumping
core.
Any DIeas at what to look for? (this is runnign 2.6.24, arch/powerpc on
a 8280)
When runnign the program on 2.6.18 arch/ppc, the program gets a sig 11
and dumps core.
On 2.6.24, I ghet the kernel oops, and then the program hangs sround
forever and is unkillable.
Unable to handle kernel paging request for data at address 0x48024000
Faulting instruction address: 0xc000ef88
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT Innovative Systems ApMax
Modules linked in: drv_wd(P) drv_scc devcom drv_pcir tipc drv_ss7
drv_auxcpu drv_leds(P) drv_ethsw proc_sysinfo(P) i2c_8266(P)
NIP: c000ef88 LR: c0012180 CTR: 00000080
REGS: eebc9b70 TRAP: 0300 Tainted: P (2.6.24)
MSR: 00009032 <EE,ME,IR,DR> CR: 24004442 XER: 00000000
DAR: 48024000, DSISR: 20000000
TASK =3D eebac3c0[3131] 'armd' THREAD: eebc8000
GPR00: ee9b7d00 eebc9c20 eebac3c0 48024000 00000080 399a4181 48024000
00000000
GPR08: 399a4181 ee9b7d00 00000000 c2000000 44004422 10100f38 ee82fc00
bfffffff
GPR16: ef377060 00000030 ee9b7d00 00000000 eebc9cdc 00000011 eebc9cd8
eeb96480
GPR24: ee9b7d00 399a4181 48024000 eeb9a370 eeb9a370 399a4181 48024000
c2733480
NIP [c000ef88] __flush_dcache_icache+0x14/0x40
LR [c0012180] update_mmu_cache+0x74/0x114
Call Trace:
[eebc9c20] [eebc8000] 0xeebc8000 (unreliable)
[eebc9c40] [c005d060] handle_mm_fault+0x630/0xbc0
[eebc9c80] [c005d9e4] get_user_pages+0x3f4/0x4fc
[eebc9cd0] [c00aa7c4] elf_core_dump+0x9a4/0xc5c
[eebc9d60] [c00779e4] do_coredump+0x6e0/0x748
[eebc9e50] [c002a5b0] get_signal_to_deliver+0x40c/0x45c
[eebc9e80] [c0008ce8] do_signal+0x50/0x294
[eebc9f40] [c000fb98] do_user_signal+0x74/0xc4
--- Exception: 300 at 0x10044efc
LR =3D 0x10044ec0
Instruction dump:
4d820020 7c8903a6 7c001bac 38630020 4200fff8 7c0004ac 4e800020 60000000
54630026 38800080 7c8903a6 7c661b78 <7c00186c> 38630020 4200fff8
7c0004ac
---[ end trace 97db37eaf213da3c ]---
note: armd[3131] exited with preempt_count 2
=20
^ permalink raw reply
* Re: Configuring Freecale ucc_geth without a PHY
From: Steven Hein @ 2008-01-31 13:38 UTC (permalink / raw)
To: Kim Phillips; +Cc: linuxppc-embedded
In-Reply-To: <20080129114310.3109caaa.kim.phillips@freescale.com>
Kim Phillips wrote:
> On Tue, 29 Jan 2008 11:08:43 -0600
> Steven Hein <ssh@sgi.com> wrote:
>
>
>> Hi all,
>>
>> I have a custom board with an MPC8358 (our board is based
>> off of the MPC8360E-MDS development board) that has its eth's
>> directly connected (GMII) to a Broadcom network switch
>> part on the same board, with no PHYs between them.
>> We've have been using a 2.6.16.18 kernel (from TimeSys) up
>> until now, and I hacked in some crude support for no-phy
>> configs forced to 100Mbit and 1Gbit speeds. Now I'm
>> moving to 2.6.22 (with 8360 the patches from bitshrine.org),
>> and I'm trying to understand how I should do this with
>> device trees, the new PHY infrastructure, etc. Has anyone
>> else needed this support? Does anyone have any suggestions
>> as to how to tackle it?
>>
>
> check out the "fixed-link" property and associated code. This
> implementation came about after 2.6.22 though (it's commit-ish
> v2.6.23-10096-ga21e282).
>
> Kim
>
Thanks for the pointer Kim! Using the "fixed-link" property
code already in the tree, and adding the glue in ucc_geth.c to
use it (modeled after the code in gianfar fix-link support
in fsl_soc.c), I was able to get this working with me 8360 board.
Is there a document anywhere that describes how to submit
patches for the powerpc kernel? Or do I just create the patch
(I'm learning about git right now...) again the paulus/powerpc.git
tree, and send it to this list?
Thanks,
Steve
--
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Steve Hein (ssh@sgi.com) Engineering Diagnostics/Software
Silicon Graphics, Inc.
1168 Industrial Blvd. Phone: (715) 726-8410
Chippewa Falls, WI 54729 Fax: (715) 726-6715
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
^ permalink raw reply
* [PATCH/RFC] [POWERPC] Add i2c pins to dts and board setup
From: Jochen Friedrich @ 2008-01-31 12:54 UTC (permalink / raw)
To: Scott Wood; +Cc: linuxppc-dev list
Add CPM i2c support for mpc8272, mpc866 and mpc885 boards.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
---
arch/powerpc/boot/dts/mpc8272ads.dts | 10 ++++++++++
arch/powerpc/boot/dts/mpc866ads.dts | 10 ++++++++++
arch/powerpc/boot/dts/mpc885ads.dts | 10 ++++++++++
arch/powerpc/platforms/82xx/mpc8272_ads.c | 5 +++++
arch/powerpc/platforms/8xx/mpc86xads_setup.c | 4 ++++
arch/powerpc/platforms/8xx/mpc885ads_setup.c | 3 +++
6 files changed, 42 insertions(+), 0 deletions(-)
diff --git a/arch/powerpc/boot/dts/mpc8272ads.dts b/arch/powerpc/boot/dts/mpc8272ads.dts
index 7285ca1..7273996 100644
--- a/arch/powerpc/boot/dts/mpc8272ads.dts
+++ b/arch/powerpc/boot/dts/mpc8272ads.dts
@@ -215,6 +215,16 @@
linux,network-index = <1>;
fsl,cpm-command = <16200300>;
};
+
+ i2c@11860 {
+ compatible = "fsl,mpc8248-i2c",
+ "fsl,cpm2-i2c",
+ "fsl,cpm-i2c";
+ reg = <11860 20 8afc 2>;
+ interrupts = <1 8>;
+ interrupt-parent = <&PIC>;
+ fsl,cpm-command = <29600000>;
+ };
};
PIC: interrupt-controller@10c00 {
diff --git a/arch/powerpc/boot/dts/mpc866ads.dts b/arch/powerpc/boot/dts/mpc866ads.dts
index daf9433..d669049 100644
--- a/arch/powerpc/boot/dts/mpc866ads.dts
+++ b/arch/powerpc/boot/dts/mpc866ads.dts
@@ -169,6 +169,16 @@
fsl,cpm-command = <0000>;
linux,network-index = <1>;
};
+
+ i2c@860 {
+ compatible = "fsl,mpc866-i2c",
+ "fsl,cpm1-i2c",
+ "fsl,cpm-i2c";
+ reg = <860 20 3c80 30>;
+ interrupts = <10>;
+ interrupt-parent = <&CPM_PIC>;
+ fsl,cpm-command = <0010>;
+ };
};
};
diff --git a/arch/powerpc/boot/dts/mpc885ads.dts b/arch/powerpc/boot/dts/mpc885ads.dts
index 8848e63..fd9c9d7 100644
--- a/arch/powerpc/boot/dts/mpc885ads.dts
+++ b/arch/powerpc/boot/dts/mpc885ads.dts
@@ -213,6 +213,16 @@
fsl,cpm-command = <0080>;
linux,network-index = <2>;
};
+
+ i2c@860 {
+ compatible = "fsl,mpc885-i2c",
+ "fsl,cpm1-i2c",
+ "fsl,cpm-i2c";
+ reg = <860 20 3c80 30>;
+ interrupts = <10>;
+ interrupt-parent = <&CPM_PIC>;
+ fsl,cpm-command = <0010>;
+ };
};
};
diff --git a/arch/powerpc/platforms/82xx/mpc8272_ads.c b/arch/powerpc/platforms/82xx/mpc8272_ads.c
index 3fce6b3..8f1862a 100644
--- a/arch/powerpc/platforms/82xx/mpc8272_ads.c
+++ b/arch/powerpc/platforms/82xx/mpc8272_ads.c
@@ -96,6 +96,11 @@ static struct cpm_pin mpc8272_ads_pins[] = {
{1, 31, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
{2, 16, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
{2, 17, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+
+ /* I2C */
+ {3, 26, CPM_PIN_INPUT | CPM_PIN_SECONDARY | CPM_PIN_OPENDRAIN},
+ {3, 27, CPM_PIN_INPUT | CPM_PIN_SECONDARY | CPM_PIN_OPENDRAIN},
+
};
static void __init init_ioports(void)
diff --git a/arch/powerpc/platforms/8xx/mpc86xads_setup.c b/arch/powerpc/platforms/8xx/mpc86xads_setup.c
index c028a5b..caaec29 100644
--- a/arch/powerpc/platforms/8xx/mpc86xads_setup.c
+++ b/arch/powerpc/platforms/8xx/mpc86xads_setup.c
@@ -65,6 +65,10 @@ static struct cpm_pin mpc866ads_pins[] = {
{CPM_PORTD, 13, CPM_PIN_OUTPUT},
{CPM_PORTD, 14, CPM_PIN_OUTPUT},
{CPM_PORTD, 15, CPM_PIN_OUTPUT},
+
+ /* I2C */
+ {CPM_PORTB, 26, CPM_PIN_INPUT | CPM_PIN_OPENDRAIN},
+ {CPM_PORTB, 27, CPM_PIN_INPUT | CPM_PIN_OPENDRAIN},
};
static void __init init_ioports(void)
diff --git a/arch/powerpc/platforms/8xx/mpc885ads_setup.c b/arch/powerpc/platforms/8xx/mpc885ads_setup.c
index 6e7ded0..45ed6cd 100644
--- a/arch/powerpc/platforms/8xx/mpc885ads_setup.c
+++ b/arch/powerpc/platforms/8xx/mpc885ads_setup.c
@@ -158,6 +158,9 @@ static struct cpm_pin mpc885ads_pins[] = {
{CPM_PORTE, 28, CPM_PIN_OUTPUT},
{CPM_PORTE, 29, CPM_PIN_OUTPUT},
#endif
+ /* I2C */
+ {CPM_PORTB, 26, CPM_PIN_INPUT | CPM_PIN_OPENDRAIN},
+ {CPM_PORTB, 27, CPM_PIN_INPUT | CPM_PIN_OPENDRAIN},
};
static void __init init_ioports(void)
--
1.5.3.8
^ permalink raw reply related
* [PATCHv4 2.6.25] i2c: adds support for i2c bus on Freescale CPM1/CPM2 controllers
From: Jochen Friedrich @ 2008-01-31 12:54 UTC (permalink / raw)
To: Scott Wood; +Cc: linux-kernel, linuxppc-dev list, i2c, Jean Delvare
Using the port of 2.4 code from Vitaly Bordug <vitb@kernel.crashing.org>
and the actual algorithm used by the i2c driver of the DBox code on
cvs.tuxboc.org from Tmbinc, Gillem (htoa@gmx.net). Renamed i2c-rpx.c and
i2c-algo-8xx.c to i2c-cpm.c and converted the driver to an
of_platform_driver.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
---
drivers/i2c/busses/Kconfig | 10 +
drivers/i2c/busses/Makefile | 1 +
drivers/i2c/busses/i2c-cpm.c | 759 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 770 insertions(+), 0 deletions(-)
create mode 100644 drivers/i2c/busses/i2c-cpm.c
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index b61f56b..1d18db7 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -114,6 +114,16 @@ config I2C_BLACKFIN_TWI_CLK_KHZ
help
The unit of the TWI clock is kHz.
+config I2C_CPM
+ tristate "Freescale CPM1 or CPM2 (MPC8xx/826x)"
+ depends on (CPM1 || CPM2) && I2C && PPC_OF
+ help
+ This supports the use of the I2C interface on Freescale
+ processors with CPM1 or CPM2.
+
+ This driver can also be built as a module. If so, the module
+ will be called i2c-cpm.
+
config I2C_DAVINCI
tristate "DaVinci I2C driver"
depends on ARCH_DAVINCI
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index ea7068f..1291e2b 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_I2C_AMD8111) += i2c-amd8111.o
obj-$(CONFIG_I2C_AT91) += i2c-at91.o
obj-$(CONFIG_I2C_AU1550) += i2c-au1550.o
obj-$(CONFIG_I2C_BLACKFIN_TWI) += i2c-bfin-twi.o
+obj-$(CONFIG_I2C_CPM) += i2c-cpm.o
obj-$(CONFIG_I2C_DAVINCI) += i2c-davinci.o
obj-$(CONFIG_I2C_ELEKTOR) += i2c-elektor.o
obj-$(CONFIG_I2C_GPIO) += i2c-gpio.o
diff --git a/drivers/i2c/busses/i2c-cpm.c b/drivers/i2c/busses/i2c-cpm.c
new file mode 100644
index 0000000..7191427
--- /dev/null
+++ b/drivers/i2c/busses/i2c-cpm.c
@@ -0,0 +1,759 @@
+/*
+ * Freescale CPM1/CPM2 I2C interface.
+ * Copyright (c) 1999 Dan Malek (dmalek@jlc.net).
+ *
+ * moved into proper i2c interface;
+ * Brad Parker (brad@heeltoe.com)
+ *
+ * (C) 2007 Montavista Software, Inc.
+ * Vitaly Bordug <vitb@kernel.crashing.org>
+ *
+ * RPX lite specific parts of the i2c interface
+ * Update: There actually isn't anything RPXLite-specific about this module.
+ * This should work for most any CPM board. The console messages have been
+ * changed to eliminate RPXLite references.
+ *
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; if not, write to the Free Software
+ Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ * moved into proper i2c interface; separated out platform specific
+ * parts into i2c-8xx.c
+ * Brad Parker (brad@heeltoe.com)
+ *
+ * Parts from dbox2_i2c.c (cvs.tuxbox.org)
+ * (C) 2000-2001 Tmbinc, Gillem (htoa@gmx.net)
+ *
+ * (C) 2007 Montavista Software, Inc.
+ * Vitaly Bordug <vitb@kernel.crashing.org>
+ *
+ * Converted to of_platform_device. Renamed to i2c-cpm.c.
+ * (C) 2007 Jochen Friedrich <jochen@scram.de>
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/errno.h>
+#include <linux/sched.h>
+#include <linux/stddef.h>
+#include <linux/i2c.h>
+#include <linux/io.h>
+#include <linux/time.h>
+#include <linux/dma-mapping.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+#include <sysdev/fsl_soc.h>
+#include <asm/cpm.h>
+
+/*
+ * Wait for patch from Jon Smirl
+ * #include "powerpc-common.h"
+ */
+
+/* Try to define this if you have an older CPU (earlier than rev D4) */
+/* However, better use a GPIO based bitbang driver in this case :/ */
+#undef I2C_CHIP_ERRATA
+
+#define CPM_MAX_READ 513
+#define CPM_MAXBD 4
+
+#define CPM_CR_INIT_TRX (0x00)
+#define CPM_CR_CLOSE_RXBD (0x07)
+
+#define I2C_EB (0x10) /* Big endian mode */
+
+/* I2C parameter RAM. */
+struct i2c_ram {
+ ushort rbase; /* Rx Buffer descriptor base address */
+ ushort tbase; /* Tx Buffer descriptor base address */
+ u_char rfcr; /* Rx function code */
+ u_char tfcr; /* Tx function code */
+ ushort mrblr; /* Max receive buffer length */
+ uint rstate; /* Internal */
+ uint rdp; /* Internal */
+ ushort rbptr; /* Rx Buffer descriptor pointer */
+ ushort rbc; /* Internal */
+ uint rxtmp; /* Internal */
+ uint tstate; /* Internal */
+ uint tdp; /* Internal */
+ ushort tbptr; /* Tx Buffer descriptor pointer */
+ ushort tbc; /* Internal */
+ uint txtmp; /* Internal */
+ char res1[4]; /* Reserved */
+ ushort rpbase; /* Relocation pointer */
+ char res2[2]; /* Reserved */
+};
+
+/* I2C Registers */
+struct i2c_reg {
+ u8 i2mod;
+ u8 res1[3];
+ u8 i2add;
+ u8 res2[3];
+ u8 i2brg;
+ u8 res3[3];
+ u8 i2com;
+ u8 res4[3];
+ u8 i2cer;
+ u8 res5[3];
+ u8 i2cmr;
+};
+
+struct cpm_i2c {
+ char *base;
+ struct of_device *ofdev;
+ struct i2c_adapter adap;
+ uint dp_addr;
+ int version; /* CPM1=1, CPM2=2 */
+ int irq;
+ int cp_command;
+ struct i2c_reg __iomem *i2c_reg;
+ struct i2c_ram __iomem *i2c_ram;
+ u16 i2c_addr;
+ wait_queue_head_t i2c_wait;
+ struct mutex i2c_mutex; /* Protects I2C CPM */
+ u_char *txbuf[CPM_MAXBD];
+ u_char *rxbuf[CPM_MAXBD];
+ u32 txdma[CPM_MAXBD];
+ u32 rxdma[CPM_MAXBD];
+};
+
+static irqreturn_t cpm_i2c_interrupt(int irq, void *dev_id)
+{
+ struct cpm_i2c *cpm;
+ struct i2c_reg __iomem *i2c_reg;
+ struct i2c_adapter *adap = dev_id;
+ int i;
+
+ cpm = i2c_get_adapdata(dev_id);
+ i2c_reg = cpm->i2c_reg;
+
+ /* Clear interrupt. */
+ i = in_8(&i2c_reg->i2cer);
+ out_8(&i2c_reg->i2cer, i);
+
+ dev_dbg(&adap->dev, "Interrupt: %x\n", i);
+
+ /* Get 'me going again. */
+ wake_up_interruptible(&cpm->i2c_wait);
+
+ return i ? IRQ_HANDLED : IRQ_NONE;
+}
+
+static void cpm_reset_i2c_params(struct cpm_i2c *cpm)
+{
+ struct i2c_ram __iomem *i2c_ram = cpm->i2c_ram;
+
+ /* Set up the IIC parameters in the parameter ram. */
+ out_be16(&i2c_ram->tbase, cpm->dp_addr);
+ out_be16(&i2c_ram->rbase, cpm->dp_addr + sizeof(cbd_t) * CPM_MAXBD);
+
+ out_8(&i2c_ram->tfcr, I2C_EB);
+ out_8(&i2c_ram->rfcr, I2C_EB);
+
+ out_be16(&i2c_ram->mrblr, CPM_MAX_READ);
+
+ out_be32(&i2c_ram->rstate, 0);
+ out_be32(&i2c_ram->rdp, 0);
+ out_be16(&i2c_ram->rbptr, in_be16(&i2c_ram->rbase));
+ out_be16(&i2c_ram->rbc, 0);
+ out_be32(&i2c_ram->rxtmp, 0);
+ out_be32(&i2c_ram->tstate, 0);
+ out_be32(&i2c_ram->tdp, 0);
+ out_be16(&i2c_ram->tbptr, in_be16(&i2c_ram->tbase));
+ out_be16(&i2c_ram->tbc, 0);
+ out_be32(&i2c_ram->txtmp, 0);
+}
+
+static void cpm_i2c_force_close(struct i2c_adapter *adap)
+{
+ struct cpm_i2c *cpm = i2c_get_adapdata(adap);
+ struct i2c_reg __iomem *i2c_reg = cpm->i2c_reg;
+
+ dev_dbg(&adap->dev, "cpm_i2c_force_close()\n");
+
+ cpm_command(cpm->cp_command, CPM_CR_CLOSE_RXBD);
+
+ out_8(&i2c_reg->i2cmr, 0x00); /* Disable all interrupts */
+ out_8(&i2c_reg->i2cer, 0xff);
+}
+
+static void cpm_i2c_parse_message(struct i2c_adapter *adap,
+ struct i2c_msg *pmsg, int num, int tx, int rx)
+{
+ cbd_t *tbdf, *rbdf;
+ u_char addr;
+ u_char *tb;
+ u_char *rb;
+ struct cpm_i2c *cpm = i2c_get_adapdata(adap);
+ struct i2c_ram __iomem *i2c_ram = cpm->i2c_ram;
+ int i, dscan;
+
+ tbdf = (cbd_t *) cpm_muram_addr(in_be16(&i2c_ram->tbase));
+ rbdf = (cbd_t *) cpm_muram_addr(in_be16(&i2c_ram->rbase));
+
+ /*
+ * This chip can't do zero length writes. However, the i2c core uses
+ * them to scan for devices. The best we can do is to convert them
+ * into 1 byte reads
+ */
+
+ dscan = ((pmsg->len == 0) && (num == 1));
+
+ addr = pmsg->addr << 1;
+ if ((pmsg->flags & I2C_M_RD) || dscan)
+ addr |= 1;
+
+ tb = cpm->txbuf[tx];
+ rb = cpm->rxbuf[rx];
+
+ /* Align read buffer */
+ rb = (u_char *) (((ulong) rb + 1) & ~1);
+
+ if ((pmsg->flags & I2C_M_RD) || dscan) {
+ /*
+ * To read, we need an empty buffer of the proper length.
+ * All that is used is the first byte for address, the remainder
+ * is just used for timing (and doesn't really have to exist).
+ */
+ tb[0] = addr; /* Device address byte w/rw flag */
+
+ dev_dbg(&adap->dev, "cpm_i2c_read(abyte=0x%x)\n", addr);
+
+ if (dscan)
+ tbdf[tx].cbd_datlen = 2;
+ else
+ tbdf[tx].cbd_datlen = pmsg->len + 1;
+
+ tbdf[tx].cbd_sc = 0;
+
+ if (!(pmsg->flags & I2C_M_NOSTART))
+ tbdf[tx].cbd_sc |= BD_I2C_START;
+ if (tx + 1 == num)
+ tbdf[tx].cbd_sc |= BD_SC_LAST | BD_SC_WRAP;
+
+ rbdf[rx].cbd_datlen = 0;
+ rbdf[rx].cbd_sc = BD_SC_EMPTY | BD_SC_INTRPT;
+
+ if (rx + 1 == CPM_MAXBD)
+ tbdf[rx].cbd_sc |= BD_SC_WRAP;
+
+ eieio();
+ tbdf[tx].cbd_sc |= BD_SC_READY;
+ } else {
+ tb[0] = addr; /* Device address byte w/rw flag */
+ for (i = 0; i < pmsg->len; i++)
+ tb[i+1] = pmsg->buf[i];
+
+ dev_dbg(&adap->dev, "cpm_iic_write(abyte=0x%x)\n", addr);
+
+ tbdf[tx].cbd_datlen = pmsg->len + 1;
+ tbdf[tx].cbd_sc = 0;
+
+ if (!(pmsg->flags & I2C_M_NOSTART))
+ tbdf[tx].cbd_sc |= BD_I2C_START;
+
+ if (tx + 1 == num)
+ tbdf[tx].cbd_sc |= BD_SC_LAST | BD_SC_WRAP;
+
+ eieio();
+ tbdf[tx].cbd_sc |= BD_SC_READY | BD_SC_INTRPT;
+
+ dev_dbg(&adap->dev, "tx sc %d %04x\n",
+ tx, tbdf[tx].cbd_sc);
+ }
+}
+
+static int cpm_i2c_check_message(struct i2c_adapter *adap,
+ struct i2c_msg *pmsg, int tx, int rx)
+{
+ cbd_t *tbdf, *rbdf;
+ u_char *tb;
+ u_char *rb;
+ struct cpm_i2c *cpm = i2c_get_adapdata(adap);
+ struct i2c_ram __iomem *i2c_ram = cpm->i2c_ram;
+ int i;
+
+ tbdf = (cbd_t *) cpm_muram_addr(in_be16(&i2c_ram->tbase));
+ rbdf = (cbd_t *) cpm_muram_addr(in_be16(&i2c_ram->rbase));
+
+ tb = cpm->txbuf[tx];
+ rb = cpm->rxbuf[rx];
+
+ /* Align read buffer */
+ rb = (u_char *) (((uint) rb + 1) & ~1);
+
+ if (pmsg->flags & I2C_M_RD) {
+ dev_dbg(&adap->dev, "rx sc %04x, rx sc %04x\n",
+ tbdf[tx].cbd_sc, rbdf[rx].cbd_sc);
+
+ if (tbdf[tx].cbd_sc & BD_SC_NAK) {
+ dev_dbg(&adap->dev, "IIC read; No ack\n");
+
+ if (pmsg->flags & I2C_M_IGNORE_NAK)
+ return 0;
+ else
+ return -EIO;
+ }
+ if (rbdf[rx].cbd_sc & BD_SC_EMPTY) {
+ dev_dbg(&adap->dev,
+ "IIC read; complete but rbuf empty\n");
+ return -EREMOTEIO;
+ }
+ if (rbdf[rx].cbd_sc & BD_SC_OV) {
+ dev_dbg(&adap->dev, "IIC read; Overrun\n");
+ return -EREMOTEIO;
+ }
+ for (i = 0; i < pmsg->len; i++)
+ pmsg->buf[i] = rb[i];
+ } else {
+ dev_dbg(&adap->dev, "tx sc %d %04x\n", tx, tbdf[tx].cbd_sc);
+
+ if (tbdf[tx].cbd_sc & BD_SC_NAK) {
+ dev_dbg(&adap->dev, "IIC write; No ack\n");
+
+ if (pmsg->flags & I2C_M_IGNORE_NAK)
+ return 0;
+ else
+ return -EIO;
+ }
+ if (tbdf[tx].cbd_sc & BD_SC_UN) {
+ dev_dbg(&adap->dev, "IIC write; Underrun\n");
+ return -EIO;
+ }
+ if (tbdf[tx].cbd_sc & BD_SC_CL) {
+ dev_dbg(&adap->dev, "IIC write; Collision\n");
+ return -EIO;
+ }
+ }
+ return 0;
+}
+
+static int cpm_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
+{
+ struct cpm_i2c *cpm = i2c_get_adapdata(adap);
+ struct i2c_reg __iomem *i2c_reg = cpm->i2c_reg;
+ struct i2c_ram __iomem *i2c_ram = cpm->i2c_ram;
+ struct i2c_msg *pmsg, *rmsg;
+ int ret, i;
+ int tptr;
+ int rptr;
+ cbd_t *tbdf, *rbdf;
+
+ if (num > CPM_MAXBD)
+ return -EINVAL;
+
+ /* Check if we have any oversized READ requests */
+ for (i = 0; i < num; i++) {
+ pmsg = &msgs[i];
+ if (pmsg->len >= CPM_MAX_READ)
+ return -EINVAL;
+ }
+
+ mutex_lock(&cpm->i2c_mutex);
+
+ /* Reset to use first buffer */
+ out_be16(&i2c_ram->rbptr, in_be16(&i2c_ram->rbase));
+ out_be16(&i2c_ram->tbptr, in_be16(&i2c_ram->tbase));
+
+ tbdf = (cbd_t *) cpm_muram_addr(in_be16(&i2c_ram->tbase));
+ rbdf = (cbd_t *) cpm_muram_addr(in_be16(&i2c_ram->rbase));
+
+ tptr = 0;
+ rptr = 0;
+
+ while (tptr < num) {
+ pmsg = &msgs[tptr];
+ dev_dbg(&adap->dev, "i2c-algo-cpm.o: " "R: %d T: %d\n",
+ rptr, tptr);
+
+ cpm_i2c_parse_message(adap, pmsg, num, tptr, rptr);
+ if (pmsg->flags & I2C_M_RD)
+ rptr++;
+ tptr++;
+ }
+ /* Start transfer now */
+ /* Chip bug, set enable here */
+ out_8(&i2c_reg->i2cmr, 0x13); /* Enable RX/TX/Error interupts */
+ out_8(&i2c_reg->i2cer, 0xff); /* Clear interrupt status */
+ out_8(&i2c_reg->i2mod, in_8(&i2c_reg->i2mod) | 1); /* Enable */
+ /* Begin transmission */
+ out_8(&i2c_reg->i2com, in_8(&i2c_reg->i2com) | 0x80);
+
+ tptr = 0;
+ rptr = 0;
+
+ while (tptr < num) {
+ /* Check for outstanding messages */
+ dev_dbg(&adap->dev, "test ready.\n");
+ if (!(tbdf[tptr].cbd_sc & BD_SC_READY)) {
+ dev_dbg(&adap->dev, "ready.\n");
+ rmsg = &msgs[tptr];
+ ret = cpm_i2c_check_message(adap, rmsg, tptr, rptr);
+ tptr++;
+ if (rmsg->flags & I2C_M_RD)
+ rptr++;
+ if (ret)
+ goto out_err;
+ } else {
+ dev_dbg(&adap->dev, "not ready.\n");
+ ret = wait_event_interruptible_timeout(cpm->i2c_wait,
+ !(tbdf[tptr].cbd_sc & BD_SC_READY), 1 * HZ);
+ if (ret == 0) {
+ ret = -EREMOTEIO;
+ dev_dbg(&adap->dev, "I2C read: timeout!\n");
+ goto out_err;
+ }
+ }
+ }
+#ifdef I2C_CHIP_ERRATA
+ /*
+ * Chip errata, clear enable. This is not needed on rev D4 CPUs.
+ * Disabling I2C too early may cause too short stop condition
+ */
+ udelay(4);
+ out_8(&i2c_reg->i2mod, in_8(&i2c_reg->i2mod) | ~1);
+#endif
+ mutex_unlock(&cpm->i2c_mutex);
+ return (num);
+
+out_err:
+ cpm_i2c_force_close(adap);
+#ifdef I2C_CHIP_ERRATA
+ /*
+ * Chip errata, clear enable. This is not needed on rev D4 CPUs.
+ */
+ out_8(&i2c_reg->i2mod, in_8(&i2c_reg->i2mod) | ~1);
+#endif
+ mutex_unlock(&cpm->i2c_mutex);
+ return ret;
+}
+
+static u32 cpm_i2c_func(struct i2c_adapter *adap)
+{
+ return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+}
+
+/* -----exported algorithm data: ------------------------------------- */
+
+static const struct i2c_algorithm cpm_i2c_algo = {
+ .master_xfer = cpm_i2c_xfer,
+ .functionality = cpm_i2c_func,
+};
+
+static const struct i2c_adapter cpm_ops = {
+ .owner = THIS_MODULE,
+ .name = "i2c-cpm",
+ .id = I2C_HW_MPC8XX_EPON,
+ .algo = &cpm_i2c_algo,
+ .class = I2C_CLASS_HWMON,
+};
+
+static int cpm_i2c_setup(struct cpm_i2c *cpm)
+{
+ struct of_device *ofdev = cpm->ofdev;
+ const u32 *data;
+ int len, ret, i;
+ void __iomem *i2c_base;
+ cbd_t *tbdf, *rbdf;
+ unsigned char brg;
+
+ pr_debug("i2c-cpm: cpm_i2c_setup()\n");
+
+ init_waitqueue_head(&cpm->i2c_wait);
+ mutex_init(&cpm->i2c_mutex);
+
+ cpm->irq = of_irq_to_resource(ofdev->node, 0, NULL);
+ if (cpm->irq == NO_IRQ)
+ return -EINVAL;
+
+ /* Install interrupt handler. */
+ ret = request_irq(cpm->irq, cpm_i2c_interrupt, 0, "cpm_i2c",
+ &cpm->adap);
+ if (ret)
+ goto out_irq;
+
+ /* IIC parameter RAM */
+ i2c_base = of_iomap(ofdev->node, 1);
+ if (i2c_base == NULL) {
+ ret = -EINVAL;
+ goto out_irq;
+ }
+
+ if (of_device_is_compatible(ofdev->node, "fsl,cpm1-i2c")) {
+
+ /* Check for and use a microcode relocation patch. */
+ cpm->i2c_ram = i2c_base;
+ cpm->i2c_addr = in_be16(&cpm->i2c_ram->rpbase);
+
+ /*
+ * Maybe should use cpm_muram_alloc instead of hardcoding
+ * this in micropatch.c
+ */
+ if (cpm->i2c_addr) {
+ cpm->i2c_ram = cpm_muram_addr(cpm->i2c_addr);
+ iounmap(i2c_base);
+ }
+
+ cpm->version = 1;
+
+ } else if (of_device_is_compatible(ofdev->node, "fsl,cpm2-i2c")) {
+ cpm->i2c_addr = cpm_muram_alloc(sizeof(struct i2c_ram), 64);
+ cpm->i2c_ram = cpm_muram_addr(cpm->i2c_addr);
+ out_be16(i2c_base, cpm->i2c_addr);
+ iounmap(i2c_base);
+
+ cpm->version = 2;
+
+ } else {
+ iounmap(i2c_base);
+ ret = -EINVAL;
+ goto out_irq;
+ }
+
+ /* I2C control/status registers */
+ cpm->i2c_reg = of_iomap(ofdev->node, 0);
+ if (cpm->i2c_reg == NULL) {
+ ret = -EINVAL;
+ goto out_ram;
+ }
+
+ data = of_get_property(ofdev->node, "fsl,cpm-command", &len);
+ if (!data || len != 4) {
+ ret = -EINVAL;
+ goto out_reg;
+ }
+ cpm->cp_command = *data;
+
+ data = of_get_property(ofdev->node, "linux,i2c-class", &len);
+ if (data && len == 4)
+ cpm->adap.class = *data;
+
+ /*
+ * Allocate space for CPM_MAXBD transmit and receive buffer
+ * descriptors in the DP ram.
+ */
+ cpm->dp_addr = cpm_muram_alloc(sizeof(cbd_t) * 2 * CPM_MAXBD, 8);
+ if (!cpm->dp_addr) {
+ ret = -ENOMEM;
+ goto out_reg;
+ }
+
+ /* Initialize Tx/Rx parameters. */
+
+ cpm_reset_i2c_params(cpm);
+
+ pr_debug("i2c-cpm: i2c_ram %x, dp_addr 0x%x\n", (uint) cpm->i2c_ram,
+ cpm->dp_addr);
+ pr_debug("i2c-cpm: tbase %d, rbase %d\n",
+ in_be16(&cpm->i2c_ram->tbase), in_be16(&cpm->i2c_ram->rbase));
+
+ tbdf = (cbd_t *) cpm_muram_addr(in_be16(&cpm->i2c_ram->tbase));
+ rbdf = (cbd_t *) cpm_muram_addr(in_be16(&cpm->i2c_ram->rbase));
+
+ /* Allocate TX and RX buffers */
+
+ for (i = 0; i < CPM_MAXBD; i++) {
+ cpm->rxbuf[i] = dma_alloc_coherent(
+ NULL, CPM_MAX_READ + 1, &cpm->rxdma[i], GFP_KERNEL);
+ if (!cpm->rxbuf[i]) {
+ ret = -ENOMEM;
+ goto out_muram;
+ }
+ rbdf[i].cbd_bufaddr = ((cpm->rxdma[i] + 1) & ~1);
+ cpm->txbuf[i] = (unsigned char *)dma_alloc_coherent(
+ NULL, CPM_MAX_READ + 1, &cpm->txdma[i], GFP_KERNEL);
+ if (!cpm->txbuf[i]) {
+ ret = -ENOMEM;
+ goto out_muram;
+ }
+ tbdf[i].cbd_bufaddr = cpm->txdma[i];
+ }
+
+ cpm_command(cpm->cp_command, CPM_CR_INIT_TRX);
+
+ /*
+ * Select an invalid address. Just make sure we don't use loopback mode
+ */
+ out_8(&cpm->i2c_reg->i2add, 0xfe);
+
+ /* Make clock run at 60 kHz. */
+
+ brg = get_brgfreq() / (32 * 2 * 60000) - 3;
+ out_8(&cpm->i2c_reg->i2brg, brg);
+
+ out_8(&cpm->i2c_reg->i2mod, 0x00);
+ out_8(&cpm->i2c_reg->i2com, 0x01); /* Master mode */
+
+ /* Disable interrupts. */
+ out_8(&cpm->i2c_reg->i2cmr, 0);
+ out_8(&cpm->i2c_reg->i2cer, 0xff);
+
+ return 0;
+
+out_muram:
+ for (i = 0; i < CPM_MAXBD; i++) {
+ if (cpm->rxbuf[i])
+ dma_free_coherent(NULL, CPM_MAX_READ + 1,
+ cpm->rxbuf[i], cpm->rxdma[i]);
+ if (cpm->txbuf[i])
+ dma_free_coherent(NULL, CPM_MAX_READ + 1,
+ cpm->txbuf[i], cpm->txdma[i]);
+ }
+ cpm_muram_free(cpm->dp_addr);
+out_reg:
+ iounmap(cpm->i2c_reg);
+out_ram:
+ if ((cpm->version == 1) && (!cpm->i2c_addr))
+ iounmap(cpm->i2c_ram);
+ if (cpm->version == 2)
+ cpm_muram_free(cpm->i2c_addr);
+out_irq:
+ free_irq(cpm->irq, &cpm->adap);
+ return ret;
+}
+
+static void cpm_i2c_shutdown(struct cpm_i2c *cpm)
+{
+ int i;
+
+ /* Shut down I2C. */
+ out_8(&cpm->i2c_reg->i2mod, in_8(&cpm->i2c_reg->i2mod) | ~1);
+
+ /* Disable interrupts */
+ out_8(&cpm->i2c_reg->i2cmr, 0);
+ out_8(&cpm->i2c_reg->i2cer, 0xff);
+
+ free_irq(cpm->irq, &cpm->adap);
+
+ /* Free all memory */
+ for (i = 0; i < CPM_MAXBD; i++) {
+ dma_free_coherent(NULL, CPM_MAX_READ + 1,
+ cpm->rxbuf[i], cpm->rxdma[i]);
+ dma_free_coherent(NULL, CPM_MAX_READ + 1,
+ cpm->txbuf[i], cpm->txdma[i]);
+ }
+
+ cpm_muram_free(cpm->dp_addr);
+ iounmap(cpm->i2c_reg);
+
+ if ((cpm->version == 1) && (!cpm->i2c_addr))
+ iounmap(cpm->i2c_ram);
+ if (cpm->version == 2)
+ cpm_muram_free(cpm->i2c_addr);
+
+ return;
+}
+
+static int __devinit cpm_i2c_probe(struct of_device *ofdev,
+ const struct of_device_id *match)
+{
+ int result;
+ struct cpm_i2c *cpm;
+
+ cpm = kzalloc(sizeof(struct cpm_i2c), GFP_KERNEL);
+ if (!cpm)
+ return -ENOMEM;
+
+ cpm->ofdev = ofdev;
+
+ dev_set_drvdata(&ofdev->dev, cpm);
+
+ cpm->adap = cpm_ops;
+ i2c_set_adapdata(&cpm->adap, cpm);
+ cpm->adap.dev.parent = &ofdev->dev;
+
+ result = cpm_i2c_setup(cpm);
+ if (result) {
+ printk(KERN_ERR "i2c-cpm: Unable to init hardware\n");
+ goto out;
+ }
+
+ /* register new adapter to i2c module... */
+
+ result = i2c_add_adapter(&cpm->adap);
+ if (result < 0) {
+ printk(KERN_ERR "i2c-cpm: Unable to register with I2C\n");
+ goto out2;
+ }
+
+ pr_debug("i2c-cpm: hw routines for %s registered.\n", cpm->adap.name);
+
+ /*
+ * Wait for patch from Jon Smirl
+ * of_register_i2c_devices(&cpm->adap, ofdev->node);
+ */
+
+ return 0;
+out2:
+ cpm_i2c_shutdown(cpm);
+out:
+ dev_set_drvdata(&ofdev->dev, NULL);
+ kfree(cpm);
+
+ return result;
+}
+
+static int __devexit cpm_i2c_remove(struct of_device *ofdev)
+{
+ struct cpm_i2c *cpm = dev_get_drvdata(&ofdev->dev);
+
+ i2c_del_adapter(&cpm->adap);
+
+ cpm_i2c_shutdown(cpm);
+
+ dev_set_drvdata(&ofdev->dev, NULL);
+ kfree(cpm);
+
+ return 0;
+}
+
+static const struct of_device_id cpm_i2c_match[] = {
+ {
+ .compatible = "fsl,cpm-i2c",
+ },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, cpm_i2c_match);
+
+static struct of_platform_driver cpm_i2c_driver = {
+ .match_table = cpm_i2c_match,
+ .probe = cpm_i2c_probe,
+ .remove = __devexit_p(cpm_i2c_remove),
+ .driver = {
+ .name = "fsl-i2c-cpm",
+ .owner = THIS_MODULE,
+ }
+};
+
+static int __init cpm_i2c_init(void)
+{
+ return of_register_platform_driver(&cpm_i2c_driver);
+}
+
+static void __exit cpm_i2c_exit(void)
+{
+ of_unregister_platform_driver(&cpm_i2c_driver);
+}
+
+module_init(cpm_i2c_init);
+module_exit(cpm_i2c_exit);
+
+MODULE_AUTHOR("Dan Malek <dmalek@jlc.net>");
+MODULE_DESCRIPTION("I2C-Bus adapter routines for CPM boards");
+MODULE_LICENSE("GPL");
--
1.5.3.8
^ permalink raw reply related
* Re: [PATCH] [POWERPC] Set dma_data correctly for direct_ops on pasemi
From: Michael Ellerman @ 2008-01-31 12:38 UTC (permalink / raw)
To: Olof Johansson; +Cc: torvalds, Paul Mackerras, linuxppc-dev
In-Reply-To: <20080131064130.GA32344@lixom.net>
[-- Attachment #1: Type: text/plain, Size: 973 bytes --]
On Thu, 2008-01-31 at 00:41 -0600, Olof Johansson wrote:
> More late-caught fallout from the mainline merge. The patch:
>
> [POWERPC] Use archdata.dma_data in dma_direct_ops and add the offset
>
> "Now that all platforms using dma_direct_offset setup the
> archdata.dma_data correctly, ..."
>
> Nope -- the pasemi iommu setup code that disables translation on the
> DMA pci device didn't set dma_data correctly.
>
> The below patch is needed, please merge as soon as practical. Thanks!
Sorry about that.
I'm confused though, didn't your device come from alloc_pci_dev() which
kzalloc()s the pci_dev which contains the archdata which contains the
dma_data, ie. dma_data will already be 0?
cheers
--
Michael Ellerman
OzLabs, IBM Australia Development Lab
wwweb: http://michael.ellerman.id.au
phone: +61 2 6212 1183 (tie line 70 21183)
We do not inherit the earth from our ancestors,
we borrow it from our children. - S.M.A.R.T Person
[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply
* Re: x86/non-x86: percpu, node ids, apic ids x86.git fixup
From: Adrian Bunk @ 2008-01-31 10:47 UTC (permalink / raw)
To: Luck, Tony
Cc: sparclinux, linux-ia64, Linux Kernel Development, Mike Travis,
Linux/PPC Development, Ivan Kokshaysky, Geert Uytterhoeven,
Ingo Molnar, Linus Torvalds, Thomas Gleixner
In-Reply-To: <1FE6DD409037234FAB833C420AA843EC757F12@orsmsx424.amr.corp.intel.com>
On Wed, Jan 30, 2008 at 11:33:29AM -0800, Luck, Tony wrote:
> > I'm having trouble replicating this error. With the latest linux-2.6.git
> > plus the patch I just sent, I get the following errors:
> >
> > drivers/input/mouse/psmouse-base.c:45: error: __param_proto causes a section type conflict
> > drivers/md/md.c:5881: error: __param_start_ro causes a section type conflict
>
> Weird. psmouse-base.c builds ok for me. Perhaps there is a compiler
> version difference? I'm running a rather old 3.4.6 that came with
> my RHEL 4.5 release.
>...
It depends on the compiler version.
And you were in the Cc of Ivan's patch that fixes it... [1]
> -Tony
cu
Adrian
[1] http://lkml.org/lkml/2007/12/27/29
--
"Is there not promise of rain?" Ling Tan asked suddenly out
of the darkness. There had been need of rain for many days.
"Only a promise," Lao Er said.
Pearl S. Buck - Dragon Seed
^ permalink raw reply
* Re: [RFC] [POWERPC] bootwrapper: build multiple cuImages
From: Jochen Friedrich @ 2008-01-31 10:21 UTC (permalink / raw)
To: Grant Likely; +Cc: scottwood, linuxppc-dev, Arnd Bergmann
In-Reply-To: <20080131003347.5779.96112.stgit@trillian.secretlab.ca>
Hi Grant,
> Currently, the kernel uses CONFIG_DEVICE_TREE to wrap a kernel image
> with a fdt blob which means for any given configuration only one dts
> file can be selected and so support for only one board can be built
>
> This patch moves the selection of the default .dts file out of the kernel
> config and into the bootwrapper makefile. The makefile chooses which
> images to build based on the kernel config and the dts source file
> name is taken directly from the image name. For example "cuImage.ebony"
> will use "ebony.dts" as the device tree source file.
Cool stuff. This should be the last step to enable multiplatform builds on
8xx etc. as Arndt asked a few days ago ;)
Thanks,
Jochen
^ permalink raw reply
* Re: x86/non-x86: percpu, node ids, apic ids x86.git fixup
From: Ingo Molnar @ 2008-01-31 9:06 UTC (permalink / raw)
To: Luck, Tony
Cc: sparclinux, linux-ia64, Linux Kernel Development, Mike Travis,
Linux/PPC Development, Geert Uytterhoeven, Thomas Gleixner,
Linus Torvalds
In-Reply-To: <1FE6DD409037234FAB833C420AA843EC78C219@orsmsx424.amr.corp.intel.com>
* Luck, Tony <tony.luck@intel.com> wrote:
> > I'll start digging on why this doesn't boot ... but you might as well
> > send the fixes so far upstream to Linus so that the SMP fix is available
>
> Well a pure 2.6.24 version compiled with CONFIG_SMP=n booted just
> fine, so the breakage is recent ... and more than likely related to
> this change.
>
> I've only had a casual dig at the failing case ... kernel dies in
> memset() as called from kmem_cache_alloc() with the address being
> written as 0x4000000000117b48 (which is off in the virtual address
> space range used by users ... not a kernel address).
hm, as far as i could check, on ia64 UP the .percpu section link
difference was the only ia64 difference i could find out of those
changes. Could you try to copy a 2.6.24 include/asm-generic/percpu.h,
include/asm-ia64.h and include/linux/percpu.h into your current tree,
and see whether that boots? If yes, then it's the percpu changes. The
patch below does this ontop of very latest -git - and it builds fine
with your UP config with a crosscompiler.
> I'll dig some more tomorrow.
thanks.
Ingo
---
include/asm-generic/percpu.h | 99 ++++++++++++++++---------------------------
include/asm-ia64/percpu.h | 57 +++++++++++++++++++-----
include/linux/percpu.h | 20 --------
3 files changed, 82 insertions(+), 94 deletions(-)
Index: linux-x86.q/include/asm-generic/percpu.h
===================================================================
--- linux-x86.q.orig/include/asm-generic/percpu.h
+++ linux-x86.q/include/asm-generic/percpu.h
@@ -3,79 +3,54 @@
#include <linux/compiler.h>
#include <linux/threads.h>
-/*
- * Determine the real variable name from the name visible in the
- * kernel sources.
- */
-#define per_cpu_var(var) per_cpu__##var
-
+#define __GENERIC_PER_CPU
#ifdef CONFIG_SMP
-/*
- * per_cpu_offset() is the offset that has to be added to a
- * percpu variable to get to the instance for a certain processor.
- *
- * Most arches use the __per_cpu_offset array for those offsets but
- * some arches have their own ways of determining the offset (x86_64, s390).
- */
-#ifndef __per_cpu_offset
extern unsigned long __per_cpu_offset[NR_CPUS];
#define per_cpu_offset(x) (__per_cpu_offset[x])
-#endif
-
-/*
- * Determine the offset for the currently active processor.
- * An arch may define __my_cpu_offset to provide a more effective
- * means of obtaining the offset to the per cpu variables of the
- * current processor.
- */
-#ifndef __my_cpu_offset
-#define __my_cpu_offset per_cpu_offset(raw_smp_processor_id())
-#define my_cpu_offset per_cpu_offset(smp_processor_id())
-#else
-#define my_cpu_offset __my_cpu_offset
-#endif
-
-/*
- * Add a offset to a pointer but keep the pointer as is.
- *
- * Only S390 provides its own means of moving the pointer.
- */
-#ifndef SHIFT_PERCPU_PTR
-#define SHIFT_PERCPU_PTR(__p, __offset) RELOC_HIDE((__p), (__offset))
-#endif
-
-/*
- * A percpu variable may point to a discarded regions. The following are
- * established ways to produce a usable pointer from the percpu variable
- * offset.
- */
-#define per_cpu(var, cpu) \
- (*SHIFT_PERCPU_PTR(&per_cpu_var(var), per_cpu_offset(cpu)))
-#define __get_cpu_var(var) \
- (*SHIFT_PERCPU_PTR(&per_cpu_var(var), my_cpu_offset))
-#define __raw_get_cpu_var(var) \
- (*SHIFT_PERCPU_PTR(&per_cpu_var(var), __my_cpu_offset))
-
-
-#ifdef CONFIG_HAVE_SETUP_PER_CPU_AREA
-extern void setup_per_cpu_areas(void);
-#endif
+/* Separate out the type, so (int[3], foo) works. */
+#define DEFINE_PER_CPU(type, name) \
+ __attribute__((__section__(".data.percpu"))) __typeof__(type) per_cpu__##name
+
+#define DEFINE_PER_CPU_SHARED_ALIGNED(type, name) \
+ __attribute__((__section__(".data.percpu.shared_aligned"))) \
+ __typeof__(type) per_cpu__##name \
+ ____cacheline_aligned_in_smp
+
+/* var is in discarded region: offset to particular copy we want */
+#define per_cpu(var, cpu) (*({ \
+ extern int simple_identifier_##var(void); \
+ RELOC_HIDE(&per_cpu__##var, __per_cpu_offset[cpu]); }))
+#define __get_cpu_var(var) per_cpu(var, smp_processor_id())
+#define __raw_get_cpu_var(var) per_cpu(var, raw_smp_processor_id())
+
+/* A macro to avoid #include hell... */
+#define percpu_modcopy(pcpudst, src, size) \
+do { \
+ unsigned int __i; \
+ for_each_possible_cpu(__i) \
+ memcpy((pcpudst)+__per_cpu_offset[__i], \
+ (src), (size)); \
+} while (0)
#else /* ! SMP */
-#define per_cpu(var, cpu) (*((void)(cpu), &per_cpu_var(var)))
-#define __get_cpu_var(var) per_cpu_var(var)
-#define __raw_get_cpu_var(var) per_cpu_var(var)
+#define DEFINE_PER_CPU(type, name) \
+ __typeof__(type) per_cpu__##name
+
+#define DEFINE_PER_CPU_SHARED_ALIGNED(type, name) \
+ DEFINE_PER_CPU(type, name)
+
+#define per_cpu(var, cpu) (*((void)(cpu), &per_cpu__##var))
+#define __get_cpu_var(var) per_cpu__##var
+#define __raw_get_cpu_var(var) per_cpu__##var
#endif /* SMP */
-#ifndef PER_CPU_ATTRIBUTES
-#define PER_CPU_ATTRIBUTES
-#endif
+#define DECLARE_PER_CPU(type, name) extern __typeof__(type) per_cpu__##name
-#define DECLARE_PER_CPU(type, name) extern PER_CPU_ATTRIBUTES \
- __typeof__(type) per_cpu_var(name)
+#define EXPORT_PER_CPU_SYMBOL(var) EXPORT_SYMBOL(per_cpu__##var)
+#define EXPORT_PER_CPU_SYMBOL_GPL(var) EXPORT_SYMBOL_GPL(per_cpu__##var)
#endif /* _ASM_GENERIC_PERCPU_H_ */
Index: linux-x86.q/include/asm-ia64/percpu.h
===================================================================
--- linux-x86.q.orig/include/asm-ia64/percpu.h
+++ linux-x86.q/include/asm-ia64/percpu.h
@@ -15,36 +15,69 @@
#include <linux/threads.h>
-#ifdef CONFIG_SMP
-
#ifdef HAVE_MODEL_SMALL_ATTRIBUTE
-# define PER_CPU_ATTRIBUTES __attribute__((__model__ (__small__)))
+# define __SMALL_ADDR_AREA __attribute__((__model__ (__small__)))
+#else
+# define __SMALL_ADDR_AREA
#endif
-#define __my_cpu_offset __ia64_per_cpu_var(local_per_cpu_offset)
+#define DECLARE_PER_CPU(type, name) \
+ extern __SMALL_ADDR_AREA __typeof__(type) per_cpu__##name
+
+/* Separate out the type, so (int[3], foo) works. */
+#define DEFINE_PER_CPU(type, name) \
+ __attribute__((__section__(".data.percpu"))) \
+ __SMALL_ADDR_AREA __typeof__(type) per_cpu__##name
+
+#ifdef CONFIG_SMP
+#define DEFINE_PER_CPU_SHARED_ALIGNED(type, name) \
+ __attribute__((__section__(".data.percpu.shared_aligned"))) \
+ __SMALL_ADDR_AREA __typeof__(type) per_cpu__##name \
+ ____cacheline_aligned_in_smp
+#else
+#define DEFINE_PER_CPU_SHARED_ALIGNED(type, name) \
+ DEFINE_PER_CPU(type, name)
+#endif
+
+/*
+ * Pretty much a literal copy of asm-generic/percpu.h, except that percpu_modcopy() is an
+ * external routine, to avoid include-hell.
+ */
+#ifdef CONFIG_SMP
+
+extern unsigned long __per_cpu_offset[NR_CPUS];
+#define per_cpu_offset(x) (__per_cpu_offset[x])
+/* Equal to __per_cpu_offset[smp_processor_id()], but faster to access: */
+DECLARE_PER_CPU(unsigned long, local_per_cpu_offset);
+
+#define per_cpu(var, cpu) (*RELOC_HIDE(&per_cpu__##var, __per_cpu_offset[cpu]))
+#define __get_cpu_var(var) (*RELOC_HIDE(&per_cpu__##var, __ia64_per_cpu_var(local_per_cpu_offset)))
+#define __raw_get_cpu_var(var) (*RELOC_HIDE(&per_cpu__##var, __ia64_per_cpu_var(local_per_cpu_offset)))
+
+extern void percpu_modcopy(void *pcpudst, const void *src, unsigned long size);
+extern void setup_per_cpu_areas (void);
extern void *per_cpu_init(void);
#else /* ! SMP */
-#define PER_CPU_ATTRIBUTES __attribute__((__section__(".data.percpu")))
-
+#define per_cpu(var, cpu) (*((void)(cpu), &per_cpu__##var))
+#define __get_cpu_var(var) per_cpu__##var
+#define __raw_get_cpu_var(var) per_cpu__##var
#define per_cpu_init() (__phys_per_cpu_start)
#endif /* SMP */
+#define EXPORT_PER_CPU_SYMBOL(var) EXPORT_SYMBOL(per_cpu__##var)
+#define EXPORT_PER_CPU_SYMBOL_GPL(var) EXPORT_SYMBOL_GPL(per_cpu__##var)
+
/*
* Be extremely careful when taking the address of this variable! Due to virtual
* remapping, it is different from the canonical address returned by __get_cpu_var(var)!
* On the positive side, using __ia64_per_cpu_var() instead of __get_cpu_var() is slightly
* more efficient.
*/
-#define __ia64_per_cpu_var(var) per_cpu__##var
-
-#include <asm-generic/percpu.h>
-
-/* Equal to __per_cpu_offset[smp_processor_id()], but faster to access: */
-DECLARE_PER_CPU(unsigned long, local_per_cpu_offset);
+#define __ia64_per_cpu_var(var) (per_cpu__##var)
#endif /* !__ASSEMBLY__ */
Index: linux-x86.q/include/linux/percpu.h
===================================================================
--- linux-x86.q.orig/include/linux/percpu.h
+++ linux-x86.q/include/linux/percpu.h
@@ -9,26 +9,6 @@
#include <asm/percpu.h>
-#ifdef CONFIG_SMP
-#define DEFINE_PER_CPU(type, name) \
- __attribute__((__section__(".data.percpu"))) \
- PER_CPU_ATTRIBUTES __typeof__(type) per_cpu__##name
-
-#define DEFINE_PER_CPU_SHARED_ALIGNED(type, name) \
- __attribute__((__section__(".data.percpu.shared_aligned"))) \
- PER_CPU_ATTRIBUTES __typeof__(type) per_cpu__##name \
- ____cacheline_aligned_in_smp
-#else
-#define DEFINE_PER_CPU(type, name) \
- PER_CPU_ATTRIBUTES __typeof__(type) per_cpu__##name
-
-#define DEFINE_PER_CPU_SHARED_ALIGNED(type, name) \
- DEFINE_PER_CPU(type, name)
-#endif
-
-#define EXPORT_PER_CPU_SYMBOL(var) EXPORT_SYMBOL(per_cpu__##var)
-#define EXPORT_PER_CPU_SYMBOL_GPL(var) EXPORT_SYMBOL_GPL(per_cpu__##var)
-
/* Enough to cover all DEFINE_PER_CPUs in kernel, including modules. */
#ifndef PERCPU_ENOUGH_ROOM
#ifdef CONFIG_MODULES
^ permalink raw reply
* RE: [PATCH 1/2] Add RapidIO node into MPC8641HPCN dts file
From: Zhang Wei @ 2008-01-31 7:36 UTC (permalink / raw)
To: galak; +Cc: linuxppc-dev
In-Reply-To: <12017655292517-git-send-email-y>
Sorry for wrong sending name of this and next email.
Best Regards,
Wei.=20
> -----Original Message-----
> From: y [mailto:y]=20
> Sent: Thursday, January 31, 2008 3:45 PM
> To: galak@kernel.crashing.org
> Cc: linuxppc-dev@ozlabs.org; Zhang Wei
> Subject: [PATCH 1/2] Add RapidIO node into MPC8641HPCN dts file
>=20
> From: Zhang Wei <wei.zhang@freescale.com>
>=20
> Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
> ---
> arch/powerpc/boot/dts/mpc8641_hpcn.dts | 13 +++++++++++++
> 1 files changed, 13 insertions(+), 0 deletions(-)
>=20
> diff --git a/arch/powerpc/boot/dts/mpc8641_hpcn.dts=20
> b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
> index 556a9ca..1a0fce5 100644
> --- a/arch/powerpc/boot/dts/mpc8641_hpcn.dts
> +++ b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
> @@ -25,6 +25,7 @@
> serial1 =3D &serial1;
> pci0 =3D &pci0;
> pci1 =3D &pci1;
> + rapidio0 =3D &rapidio0;
> };
> =20
> cpus {
> @@ -499,4 +500,16 @@
> 0 00100000>;
> };
> };
> +
> + rapidio0: rapidio@f80c0000 {
> + #address-cells =3D <2>;
> + #size-cells =3D <2>;
> + compatible =3D "fsl,rapidio-delta";
> + reg =3D <f80c0000 20000>;
> + ranges =3D <0 0 c0000000 0 20000000>;
> + interrupt-parent =3D <&mpic>;
> + /* err_irq bell_outb_irq bell_inb_irq
> + msg1_tx_irq msg1_rx_irq msg2_tx_irq=20
> msg2_rx_irq */
> + interrupts =3D <30 2 31 2 32 2 35 2 36 2 37 2 38 2>;
> + };
> };
> --=20
> 1.5.2
>=20
>=20
^ permalink raw reply
* [PATCH 2/2] Add RapidIO node probing into MPC86xx_HPCN board id table.
From: Zhang Wei @ 2008-01-31 7:46 UTC (permalink / raw)
To: galak; +Cc: linuxppc-dev
In-Reply-To: <12017656032841-git-send-email-wei.zhang@freescale.com>
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
---
arch/powerpc/platforms/86xx/mpc86xx_hpcn.c | 1 +
1 files changed, 1 insertions(+), 0 deletions(-)
diff --git a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
index cfbe8c5..4a3e421 100644
--- a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
+++ b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
@@ -215,6 +215,7 @@ mpc86xx_time_init(void)
static __initdata struct of_device_id of_bus_ids[] = {
{ .compatible = "simple-bus", },
+ { .compatible = "fsl,rapidio-delta", },
{},
};
--
1.5.2
^ permalink raw reply related
* [PATCH 1/2] Add RapidIO node into MPC8641HPCN dts file
From: Zhang Wei @ 2008-01-31 7:46 UTC (permalink / raw)
To: galak; +Cc: linuxppc-dev
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
---
arch/powerpc/boot/dts/mpc8641_hpcn.dts | 13 +++++++++++++
1 files changed, 13 insertions(+), 0 deletions(-)
diff --git a/arch/powerpc/boot/dts/mpc8641_hpcn.dts b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
index 556a9ca..1a0fce5 100644
--- a/arch/powerpc/boot/dts/mpc8641_hpcn.dts
+++ b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
@@ -25,6 +25,7 @@
serial1 = &serial1;
pci0 = &pci0;
pci1 = &pci1;
+ rapidio0 = &rapidio0;
};
cpus {
@@ -499,4 +500,16 @@
0 00100000>;
};
};
+
+ rapidio0: rapidio@f80c0000 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "fsl,rapidio-delta";
+ reg = <f80c0000 20000>;
+ ranges = <0 0 c0000000 0 20000000>;
+ interrupt-parent = <&mpic>;
+ /* err_irq bell_outb_irq bell_inb_irq
+ msg1_tx_irq msg1_rx_irq msg2_tx_irq msg2_rx_irq */
+ interrupts = <30 2 31 2 32 2 35 2 36 2 37 2 38 2>;
+ };
};
--
1.5.2
^ permalink raw reply related
* [PATCH 2/2] Add RapidIO node probing into MPC86xx_HPCN board id table.
From: y @ 2008-01-31 7:45 UTC (permalink / raw)
To: galak; +Cc: linuxppc-dev
In-Reply-To: <12017655292517-git-send-email-y>
From: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
---
arch/powerpc/platforms/86xx/mpc86xx_hpcn.c | 1 +
1 files changed, 1 insertions(+), 0 deletions(-)
diff --git a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
index cfbe8c5..4a3e421 100644
--- a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
+++ b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
@@ -215,6 +215,7 @@ mpc86xx_time_init(void)
static __initdata struct of_device_id of_bus_ids[] = {
{ .compatible = "simple-bus", },
+ { .compatible = "fsl,rapidio-delta", },
{},
};
--
1.5.2
^ permalink raw reply related
* [PATCH 1/2] Add RapidIO node into MPC8641HPCN dts file
From: y @ 2008-01-31 7:45 UTC (permalink / raw)
To: galak; +Cc: linuxppc-dev
From: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
---
arch/powerpc/boot/dts/mpc8641_hpcn.dts | 13 +++++++++++++
1 files changed, 13 insertions(+), 0 deletions(-)
diff --git a/arch/powerpc/boot/dts/mpc8641_hpcn.dts b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
index 556a9ca..1a0fce5 100644
--- a/arch/powerpc/boot/dts/mpc8641_hpcn.dts
+++ b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
@@ -25,6 +25,7 @@
serial1 = &serial1;
pci0 = &pci0;
pci1 = &pci1;
+ rapidio0 = &rapidio0;
};
cpus {
@@ -499,4 +500,16 @@
0 00100000>;
};
};
+
+ rapidio0: rapidio@f80c0000 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "fsl,rapidio-delta";
+ reg = <f80c0000 20000>;
+ ranges = <0 0 c0000000 0 20000000>;
+ interrupt-parent = <&mpic>;
+ /* err_irq bell_outb_irq bell_inb_irq
+ msg1_tx_irq msg1_rx_irq msg2_tx_irq msg2_rx_irq */
+ interrupts = <30 2 31 2 32 2 35 2 36 2 37 2 38 2>;
+ };
};
--
1.5.2
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox