* [PATCH V3 0/4] mpc5200 audio rework for AC97
From: Jon Smirl @ 2009-05-25 1:38 UTC (permalink / raw)
To: grant.likely, linuxppc-dev, alsa-devel, broonie
The following series implements audio support for the mpc5200. It adds an AC97 driver and STAC9766 codec driver.
Board support for the Efika and Phytec pcm030 are also included.
I've tried to implement the feedback received on the previous two versions.
based on commit 0bc53a67ac831ec84f730a657dbcadd80a589ef5 on broonie/for-2.6.31 at
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6.git
---
Jon Smirl (4):
Fabric bindings for STAC9766 on the Efika
Support for AC97 on Phytec pmc030 base board.
AC97 driver for mpc5200
Main rewite of the mpc5200 audio DMA code
sound/soc/fsl/Kconfig | 27 ++
sound/soc/fsl/Makefile | 5
sound/soc/fsl/efika-audio-fabric.c | 95 +++++++
sound/soc/fsl/mpc5200_dma.c | 504 +++++++++++++++++++++++------------
sound/soc/fsl/mpc5200_dma.h | 33 +-
sound/soc/fsl/mpc5200_psc_ac97.c | 392 +++++++++++++++++++++++++++
sound/soc/fsl/mpc5200_psc_ac97.h | 15 +
sound/soc/fsl/mpc5200_psc_i2s.c | 247 +++--------------
sound/soc/fsl/mpc5200_psc_i2s.h | 12 +
sound/soc/fsl/pcm030-audio-fabric.c | 95 +++++++
10 files changed, 1036 insertions(+), 389 deletions(-)
create mode 100644 sound/soc/fsl/efika-audio-fabric.c
create mode 100644 sound/soc/fsl/mpc5200_psc_ac97.c
create mode 100644 sound/soc/fsl/mpc5200_psc_ac97.h
create mode 100644 sound/soc/fsl/mpc5200_psc_i2s.h
create mode 100644 sound/soc/fsl/pcm030-audio-fabric.c
--
Jon Smirl
jonsmirl@gmail.com
^ permalink raw reply
* [PATCH V3 1/4] Main rewite of the mpc5200 audio DMA code
From: Jon Smirl @ 2009-05-25 1:38 UTC (permalink / raw)
To: grant.likely, linuxppc-dev, alsa-devel, broonie
In-Reply-To: <20090525013606.3073.86753.stgit@terra>
Rewrite the mpc5200 audio DMA code to support both I2S and AC97.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
---
sound/soc/fsl/Kconfig | 1
sound/soc/fsl/mpc5200_dma.c | 504 ++++++++++++++++++++++++++-------------
sound/soc/fsl/mpc5200_dma.h | 33 +--
sound/soc/fsl/mpc5200_psc_i2s.c | 247 +++----------------
sound/soc/fsl/mpc5200_psc_i2s.h | 12 +
5 files changed, 408 insertions(+), 389 deletions(-)
create mode 100644 sound/soc/fsl/mpc5200_psc_i2s.h
diff --git a/sound/soc/fsl/Kconfig b/sound/soc/fsl/Kconfig
index dc79bdf..1918c78 100644
--- a/sound/soc/fsl/Kconfig
+++ b/sound/soc/fsl/Kconfig
@@ -25,7 +25,6 @@ config SND_SOC_MPC8610_HPCD
config SND_SOC_MPC5200_I2S
tristate "Freescale MPC5200 PSC in I2S mode driver"
depends on PPC_MPC52xx && PPC_BESTCOMM
- select SND_SOC_OF_SIMPLE
select SND_MPC52xx_DMA
select PPC_BESTCOMM_GEN_BD
help
diff --git a/sound/soc/fsl/mpc5200_dma.c b/sound/soc/fsl/mpc5200_dma.c
index 6850392..4e1f1f8 100644
--- a/sound/soc/fsl/mpc5200_dma.c
+++ b/sound/soc/fsl/mpc5200_dma.c
@@ -3,23 +3,13 @@
* ALSA SoC Platform driver
*
* Copyright (C) 2008 Secret Lab Technologies Ltd.
+ * Copyright (C) 2009 Jon Smirl, Digispeaker
*/
-#include <linux/init.h>
#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/device.h>
-#include <linux/delay.h>
#include <linux/of_device.h>
-#include <linux/of_platform.h>
-#include <linux/dma-mapping.h>
-#include <sound/core.h>
-#include <sound/pcm.h>
-#include <sound/pcm_params.h>
-#include <sound/initval.h>
#include <sound/soc.h>
-#include <sound/soc-of-simple.h>
#include <sysdev/bestcomm/bestcomm.h>
#include <sysdev/bestcomm/gen_bd.h>
@@ -27,10 +17,6 @@
#include "mpc5200_dma.h"
-MODULE_AUTHOR("Grant Likely <grant.likely@secretlab.ca>");
-MODULE_DESCRIPTION("Freescale MPC5200 PSC in DMA mode ASoC Driver");
-MODULE_LICENSE("GPL");
-
/*
* Interrupt handlers
*/
@@ -50,7 +36,7 @@ static irqreturn_t psc_dma_status_irq(int irq, void *_psc_dma)
if (psc_dma->capture.active && (isr & MPC52xx_PSC_IMR_ORERR))
psc_dma->stats.overrun_count++;
- out_8(®s->command, 4 << 4); /* reset the error status */
+ out_8(®s->command, MPC52xx_PSC_RST_ERR_STAT);
return IRQ_HANDLED;
}
@@ -81,8 +67,21 @@ static void psc_dma_bcom_enqueue_next_buffer(struct psc_dma_stream *s)
s->period_next_pt = s->period_start;
}
+static void psc_dma_bcom_enqueue_tx(struct psc_dma_stream *s)
+{
+ while (s->appl_ptr < s->runtime->control->appl_ptr) {
+
+ if (bcom_queue_full(s->bcom_task))
+ return;
+
+ s->appl_ptr += s->period_size;
+
+ psc_dma_bcom_enqueue_next_buffer(s);
+ }
+}
+
/* Bestcomm DMA irq handler */
-static irqreturn_t psc_dma_bcom_irq(int irq, void *_psc_dma_stream)
+static irqreturn_t psc_dma_bcom_irq_tx(int irq, void *_psc_dma_stream)
{
struct psc_dma_stream *s = _psc_dma_stream;
@@ -90,12 +89,12 @@ static irqreturn_t psc_dma_bcom_irq(int irq, void *_psc_dma_stream)
* and enqueue a new one in it's place. */
while (bcom_buffer_done(s->bcom_task)) {
bcom_retrieve_buffer(s->bcom_task, NULL, NULL);
+
s->period_current_pt += s->period_bytes;
if (s->period_current_pt >= s->period_end)
s->period_current_pt = s->period_start;
- psc_dma_bcom_enqueue_next_buffer(s);
- bcom_enable(s->bcom_task);
}
+ psc_dma_bcom_enqueue_tx(s);
/* If the stream is active, then also inform the PCM middle layer
* of the period finished event. */
@@ -105,49 +104,31 @@ static irqreturn_t psc_dma_bcom_irq(int irq, void *_psc_dma_stream)
return IRQ_HANDLED;
}
-/**
- * psc_dma_startup: create a new substream
- *
- * This is the first function called when a stream is opened.
- *
- * If this is the first stream open, then grab the IRQ and program most of
- * the PSC registers.
- */
-int psc_dma_startup(struct snd_pcm_substream *substream,
- struct snd_soc_dai *dai)
+static irqreturn_t psc_dma_bcom_irq_rx(int irq, void *_psc_dma_stream)
{
- struct snd_soc_pcm_runtime *rtd = substream->private_data;
- struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data;
- int rc;
+ struct psc_dma_stream *s = _psc_dma_stream;
- dev_dbg(psc_dma->dev, "psc_dma_startup(substream=%p)\n", substream);
+ /* For each finished period, dequeue the completed period buffer
+ * and enqueue a new one in it's place. */
+ while (bcom_buffer_done(s->bcom_task)) {
+ bcom_retrieve_buffer(s->bcom_task, NULL, NULL);
- if (!psc_dma->playback.active &&
- !psc_dma->capture.active) {
- /* Setup the IRQs */
- rc = request_irq(psc_dma->irq, &psc_dma_status_irq, IRQF_SHARED,
- "psc-dma-status", psc_dma);
- rc |= request_irq(psc_dma->capture.irq,
- &psc_dma_bcom_irq, IRQF_SHARED,
- "psc-dma-capture", &psc_dma->capture);
- rc |= request_irq(psc_dma->playback.irq,
- &psc_dma_bcom_irq, IRQF_SHARED,
- "psc-dma-playback", &psc_dma->playback);
- if (rc) {
- free_irq(psc_dma->irq, psc_dma);
- free_irq(psc_dma->capture.irq,
- &psc_dma->capture);
- free_irq(psc_dma->playback.irq,
- &psc_dma->playback);
- return -ENODEV;
- }
+ s->period_current_pt += s->period_bytes;
+ if (s->period_current_pt >= s->period_end)
+ s->period_current_pt = s->period_start;
+
+ psc_dma_bcom_enqueue_next_buffer(s);
}
- return 0;
+ /* If the stream is active, then also inform the PCM middle layer
+ * of the period finished event. */
+ if (s->active)
+ snd_pcm_period_elapsed(s->stream);
+
+ return IRQ_HANDLED;
}
-int psc_dma_hw_free(struct snd_pcm_substream *substream,
- struct snd_soc_dai *dai)
+static int psc_dma_hw_free(struct snd_pcm_substream *substream)
{
snd_pcm_set_runtime_buffer(substream, NULL);
return 0;
@@ -159,8 +140,7 @@ int psc_dma_hw_free(struct snd_pcm_substream *substream,
* This function is called by ALSA to start, stop, pause, and resume the DMA
* transfer of data.
*/
-int psc_dma_trigger(struct snd_pcm_substream *substream, int cmd,
- struct snd_soc_dai *dai)
+static int psc_dma_trigger(struct snd_pcm_substream *substream, int cmd)
{
struct snd_soc_pcm_runtime *rtd = substream->private_data;
struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data;
@@ -168,8 +148,8 @@ int psc_dma_trigger(struct snd_pcm_substream *substream, int cmd,
struct psc_dma_stream *s;
struct mpc52xx_psc __iomem *regs = psc_dma->psc_regs;
u16 imr;
- u8 psc_cmd;
unsigned long flags;
+ int i;
if (substream->pstr->stream == SNDRV_PCM_STREAM_CAPTURE)
s = &psc_dma->capture;
@@ -189,68 +169,45 @@ int psc_dma_trigger(struct snd_pcm_substream *substream, int cmd,
(s->period_bytes * runtime->periods);
s->period_next_pt = s->period_start;
s->period_current_pt = s->period_start;
+ s->period_size = runtime->period_size;
s->active = 1;
- /* First; reset everything */
+ /* track appl_ptr so that we have a better chance of detecting
+ * end of stream and not over running it.
+ */
+ s->runtime = runtime;
+ s->appl_ptr = s->runtime->control->appl_ptr -
+ (runtime->period_size * runtime->periods);
+
+ /* Fill up the bestcomm bd queue and enable DMA.
+ * This will begin filling the PSC's fifo.
+ */
if (substream->pstr->stream == SNDRV_PCM_STREAM_CAPTURE) {
- out_8(®s->command, MPC52xx_PSC_RST_RX);
- out_8(®s->command, MPC52xx_PSC_RST_ERR_STAT);
+ bcom_gen_bd_rx_reset(s->bcom_task);
+ for (i = 0; i < runtime->periods; i++)
+ if (!bcom_queue_full(s->bcom_task))
+ psc_dma_bcom_enqueue_next_buffer(s);
} else {
- out_8(®s->command, MPC52xx_PSC_RST_TX);
- out_8(®s->command, MPC52xx_PSC_RST_ERR_STAT);
+ bcom_gen_bd_tx_reset(s->bcom_task);
+ psc_dma_bcom_enqueue_tx(s);
}
- /* Next, fill up the bestcomm bd queue and enable DMA.
- * This will begin filling the PSC's fifo. */
- if (substream->pstr->stream == SNDRV_PCM_STREAM_CAPTURE)
- bcom_gen_bd_rx_reset(s->bcom_task);
- else
- bcom_gen_bd_tx_reset(s->bcom_task);
- while (!bcom_queue_full(s->bcom_task))
- psc_dma_bcom_enqueue_next_buffer(s);
bcom_enable(s->bcom_task);
- /* Due to errata in the dma mode; need to line up enabling
- * the transmitter with a transition on the frame sync
- * line */
-
spin_lock_irqsave(&psc_dma->lock, flags);
- /* first make sure it is low */
- while ((in_8(®s->ipcr_acr.ipcr) & 0x80) != 0)
- ;
- /* then wait for the transition to high */
- while ((in_8(®s->ipcr_acr.ipcr) & 0x80) == 0)
- ;
- /* Finally, enable the PSC.
- * Receiver must always be enabled; even when we only want
- * transmit. (see 15.3.2.3 of MPC5200B User's Guide) */
- psc_cmd = MPC52xx_PSC_RX_ENABLE;
- if (substream->pstr->stream == SNDRV_PCM_STREAM_PLAYBACK)
- psc_cmd |= MPC52xx_PSC_TX_ENABLE;
- out_8(®s->command, psc_cmd);
+ out_8(®s->command, MPC52xx_PSC_RST_ERR_STAT);
spin_unlock_irqrestore(&psc_dma->lock, flags);
break;
case SNDRV_PCM_TRIGGER_STOP:
- /* Turn off the PSC */
s->active = 0;
- if (substream->pstr->stream == SNDRV_PCM_STREAM_CAPTURE) {
- if (!psc_dma->playback.active) {
- out_8(®s->command, 2 << 4); /* reset rx */
- out_8(®s->command, 3 << 4); /* reset tx */
- out_8(®s->command, 4 << 4); /* reset err */
- }
- } else {
- out_8(®s->command, 3 << 4); /* reset tx */
- out_8(®s->command, 4 << 4); /* reset err */
- if (!psc_dma->capture.active)
- out_8(®s->command, 2 << 4); /* reset rx */
- }
bcom_disable(s->bcom_task);
- while (!bcom_queue_empty(s->bcom_task))
- bcom_retrieve_buffer(s->bcom_task, NULL, NULL);
+ if (substream->pstr->stream == SNDRV_PCM_STREAM_CAPTURE)
+ bcom_gen_bd_rx_reset(s->bcom_task);
+ else
+ bcom_gen_bd_tx_reset(s->bcom_task);
break;
@@ -265,44 +222,11 @@ int psc_dma_trigger(struct snd_pcm_substream *substream, int cmd,
imr |= MPC52xx_PSC_IMR_TXEMP;
if (psc_dma->capture.active)
imr |= MPC52xx_PSC_IMR_ORERR;
- out_be16(®s->isr_imr.imr, imr);
+ out_be16(®s->isr_imr.imr, psc_dma->imr | imr);
return 0;
}
-/**
- * psc_dma_shutdown: shutdown the data transfer on a stream
- *
- * Shutdown the PSC if there are no other substreams open.
- */
-void psc_dma_shutdown(struct snd_pcm_substream *substream,
- struct snd_soc_dai *dai)
-{
- struct snd_soc_pcm_runtime *rtd = substream->private_data;
- struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data;
-
- dev_dbg(psc_dma->dev, "psc_dma_shutdown(substream=%p)\n", substream);
-
- /*
- * If this is the last active substream, disable the PSC and release
- * the IRQ.
- */
- if (!psc_dma->playback.active &&
- !psc_dma->capture.active) {
-
- /* Disable all interrupts and reset the PSC */
- out_be16(&psc_dma->psc_regs->isr_imr.imr, 0);
- out_8(&psc_dma->psc_regs->command, 3 << 4); /* reset tx */
- out_8(&psc_dma->psc_regs->command, 2 << 4); /* reset rx */
- out_8(&psc_dma->psc_regs->command, 1 << 4); /* reset mode */
- out_8(&psc_dma->psc_regs->command, 4 << 4); /* reset error */
-
- /* Release irqs */
- free_irq(psc_dma->irq, psc_dma);
- free_irq(psc_dma->capture.irq, &psc_dma->capture);
- free_irq(psc_dma->playback.irq, &psc_dma->playback);
- }
-}
/* ---------------------------------------------------------------------
* The PSC DMA 'ASoC platform' driver
@@ -312,62 +236,78 @@ void psc_dma_shutdown(struct snd_pcm_substream *substream,
* interaction with the attached codec
*/
-static const struct snd_pcm_hardware psc_dma_pcm_hardware = {
+static const struct snd_pcm_hardware psc_dma_hardware = {
.info = SNDRV_PCM_INFO_MMAP | SNDRV_PCM_INFO_MMAP_VALID |
SNDRV_PCM_INFO_INTERLEAVED | SNDRV_PCM_INFO_BLOCK_TRANSFER |
SNDRV_PCM_INFO_BATCH,
.formats = SNDRV_PCM_FMTBIT_S8 | SNDRV_PCM_FMTBIT_S16_BE |
- SNDRV_PCM_FMTBIT_S24_BE | SNDRV_PCM_FMTBIT_S32_BE,
+ SNDRV_PCM_FMTBIT_S24_BE | SNDRV_PCM_FMTBIT_S32_BE,
.rate_min = 8000,
.rate_max = 48000,
- .channels_min = 2,
+ .channels_min = 1,
.channels_max = 2,
.period_bytes_max = 1024 * 1024,
.period_bytes_min = 32,
.periods_min = 2,
.periods_max = 256,
.buffer_bytes_max = 2 * 1024 * 1024,
- .fifo_size = 0,
+ .fifo_size = 512,
};
-static int psc_dma_pcm_open(struct snd_pcm_substream *substream)
+static int psc_dma_open(struct snd_pcm_substream *substream)
{
+ struct snd_pcm_runtime *runtime = substream->runtime;
struct snd_soc_pcm_runtime *rtd = substream->private_data;
struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data;
struct psc_dma_stream *s;
+ int rc;
- dev_dbg(psc_dma->dev, "psc_dma_pcm_open(substream=%p)\n", substream);
+ dev_dbg(psc_dma->dev, "psc_dma_open(substream=%p)\n", substream);
if (substream->pstr->stream == SNDRV_PCM_STREAM_CAPTURE)
s = &psc_dma->capture;
else
s = &psc_dma->playback;
- snd_soc_set_runtime_hwparams(substream, &psc_dma_pcm_hardware);
+ snd_soc_set_runtime_hwparams(substream, &psc_dma_hardware);
+
+ rc = snd_pcm_hw_constraint_integer(runtime,
+ SNDRV_PCM_HW_PARAM_PERIODS);
+ if (rc < 0) {
+ dev_err(substream->pcm->card->dev, "invalid buffer size\n");
+ return rc;
+ }
s->stream = substream;
return 0;
}
-static int psc_dma_pcm_close(struct snd_pcm_substream *substream)
+static int psc_dma_close(struct snd_pcm_substream *substream)
{
struct snd_soc_pcm_runtime *rtd = substream->private_data;
struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data;
struct psc_dma_stream *s;
- dev_dbg(psc_dma->dev, "psc_dma_pcm_close(substream=%p)\n", substream);
+ dev_dbg(psc_dma->dev, "psc_dma_close(substream=%p)\n", substream);
if (substream->pstr->stream == SNDRV_PCM_STREAM_CAPTURE)
s = &psc_dma->capture;
else
s = &psc_dma->playback;
+ if (!psc_dma->playback.active &&
+ !psc_dma->capture.active) {
+
+ /* Disable all interrupts and reset the PSC */
+ out_be16(&psc_dma->psc_regs->isr_imr.imr, psc_dma->imr);
+ out_8(&psc_dma->psc_regs->command, 4 << 4); /* reset error */
+ }
s->stream = NULL;
return 0;
}
static snd_pcm_uframes_t
-psc_dma_pcm_pointer(struct snd_pcm_substream *substream)
+psc_dma_pointer(struct snd_pcm_substream *substream)
{
struct snd_soc_pcm_runtime *rtd = substream->private_data;
struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data;
@@ -384,60 +324,78 @@ psc_dma_pcm_pointer(struct snd_pcm_substream *substream)
return bytes_to_frames(substream->runtime, count);
}
-static struct snd_pcm_ops psc_dma_pcm_ops = {
- .open = psc_dma_pcm_open,
- .close = psc_dma_pcm_close,
+static int
+psc_dma_hw_params(struct snd_pcm_substream *substream,
+ struct snd_pcm_hw_params *params)
+{
+ snd_pcm_set_runtime_buffer(substream, &substream->dma_buffer);
+
+ return 0;
+}
+
+static struct snd_pcm_ops psc_dma_ops = {
+ .open = psc_dma_open,
+ .close = psc_dma_close,
+ .hw_free = psc_dma_hw_free,
.ioctl = snd_pcm_lib_ioctl,
- .pointer = psc_dma_pcm_pointer,
+ .pointer = psc_dma_pointer,
+ .trigger = psc_dma_trigger,
+ .hw_params = psc_dma_hw_params,
};
-static u64 psc_dma_pcm_dmamask = 0xffffffff;
-static int psc_dma_pcm_new(struct snd_card *card, struct snd_soc_dai *dai,
+static u64 psc_dma_dmamask = 0xffffffff;
+static int psc_dma_new(struct snd_card *card, struct snd_soc_dai *dai,
struct snd_pcm *pcm)
{
struct snd_soc_pcm_runtime *rtd = pcm->private_data;
- size_t size = psc_dma_pcm_hardware.buffer_bytes_max;
+ struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data;
+ size_t size = psc_dma_hardware.buffer_bytes_max;
int rc = 0;
- dev_dbg(rtd->socdev->dev, "psc_dma_pcm_new(card=%p, dai=%p, pcm=%p)\n",
+ dev_dbg(rtd->socdev->dev, "psc_dma_new(card=%p, dai=%p, pcm=%p)\n",
card, dai, pcm);
if (!card->dev->dma_mask)
- card->dev->dma_mask = &psc_dma_pcm_dmamask;
+ card->dev->dma_mask = &psc_dma_dmamask;
if (!card->dev->coherent_dma_mask)
card->dev->coherent_dma_mask = 0xffffffff;
if (pcm->streams[0].substream) {
- rc = snd_dma_alloc_pages(SNDRV_DMA_TYPE_DEV, pcm->dev, size,
- &pcm->streams[0].substream->dma_buffer);
+ rc = snd_dma_alloc_pages(SNDRV_DMA_TYPE_DEV, pcm->card->dev,
+ size, &pcm->streams[0].substream->dma_buffer);
if (rc)
goto playback_alloc_err;
}
if (pcm->streams[1].substream) {
- rc = snd_dma_alloc_pages(SNDRV_DMA_TYPE_DEV, pcm->dev, size,
- &pcm->streams[1].substream->dma_buffer);
+ rc = snd_dma_alloc_pages(SNDRV_DMA_TYPE_DEV, pcm->card->dev,
+ size, &pcm->streams[1].substream->dma_buffer);
if (rc)
goto capture_alloc_err;
}
+ if (rtd->socdev->card->codec->ac97)
+ rtd->socdev->card->codec->ac97->private_data = psc_dma;
+
return 0;
capture_alloc_err:
if (pcm->streams[0].substream)
snd_dma_free_pages(&pcm->streams[0].substream->dma_buffer);
+
playback_alloc_err:
dev_err(card->dev, "Cannot allocate buffer(s)\n");
+
return -ENOMEM;
}
-static void psc_dma_pcm_free(struct snd_pcm *pcm)
+static void psc_dma_free(struct snd_pcm *pcm)
{
struct snd_soc_pcm_runtime *rtd = pcm->private_data;
struct snd_pcm_substream *substream;
int stream;
- dev_dbg(rtd->socdev->dev, "psc_dma_pcm_free(pcm=%p)\n", pcm);
+ dev_dbg(rtd->socdev->dev, "psc_dma_free(pcm=%p)\n", pcm);
for (stream = 0; stream < 2; stream++) {
substream = pcm->streams[stream].substream;
@@ -449,10 +407,224 @@ static void psc_dma_pcm_free(struct snd_pcm *pcm)
}
}
-struct snd_soc_platform psc_dma_pcm_soc_platform = {
+struct snd_soc_platform mpc5200_audio_dma_platform = {
.name = "mpc5200-psc-audio",
- .pcm_ops = &psc_dma_pcm_ops,
- .pcm_new = &psc_dma_pcm_new,
- .pcm_free = &psc_dma_pcm_free,
+ .pcm_ops = &psc_dma_ops,
+ .pcm_new = &psc_dma_new,
+ .pcm_free = &psc_dma_free,
};
+EXPORT_SYMBOL_GPL(mpc5200_audio_dma_platform);
+
+/* ---------------------------------------------------------------------
+ * Sysfs attributes for error monitoring
+ */
+
+static ssize_t psc_dma_status_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct psc_dma *psc_dma = dev_get_drvdata(dev);
+
+ return sprintf(buf, "status=%.4x sicr=%.8x rfnum=%i rfstat=0x%.4x "
+ "tfnum=%i tfstat=0x%.4x\n",
+ in_be16(&psc_dma->psc_regs->sr_csr.status),
+ in_be32(&psc_dma->psc_regs->sicr),
+ in_be16(&psc_dma->fifo_regs->rfnum) & 0x1ff,
+ in_be16(&psc_dma->fifo_regs->rfstat),
+ in_be16(&psc_dma->fifo_regs->tfnum) & 0x1ff,
+ in_be16(&psc_dma->fifo_regs->tfstat));
+}
+
+static unsigned long *psc_dma_get_stat_attr(struct psc_dma *psc_dma,
+ const char *name)
+{
+ if (strcmp(name, "playback_underrun") == 0)
+ return &psc_dma->stats.underrun_count;
+ if (strcmp(name, "capture_overrun") == 0)
+ return &psc_dma->stats.overrun_count;
+
+ return 0;
+}
+
+static ssize_t psc_dma_stat_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct psc_dma *psc_dma = dev_get_drvdata(dev);
+ unsigned long *attrib;
+
+ attrib = psc_dma_get_stat_attr(psc_dma, attr->attr.name);
+ if (!attrib)
+ return 0;
+
+ return sprintf(buf, "%lu\n", *attrib);
+}
+static ssize_t psc_dma_stat_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf,
+ size_t count)
+{
+ struct psc_dma *psc_dma = dev_get_drvdata(dev);
+ unsigned long *attrib;
+
+ attrib = psc_dma_get_stat_attr(psc_dma, attr->attr.name);
+ if (!attrib)
+ return 0;
+
+ strict_strtoul(buf, 10, attrib);
+ return count;
+}
+
+static DEVICE_ATTR(status, 0644, psc_dma_status_show, NULL);
+static DEVICE_ATTR(playback_underrun, 0644, psc_dma_stat_show,
+ psc_dma_stat_store);
+static DEVICE_ATTR(capture_overrun, 0644, psc_dma_stat_show,
+ psc_dma_stat_store);
+
+
+int mpc5200_audio_dma_create(struct of_device *op)
+{
+ phys_addr_t fifo;
+ struct psc_dma *psc_dma;
+ struct resource res;
+ int size, irq, rc;
+ const __be32 *prop;
+ void __iomem *regs;
+
+ /* Fetch the registers and IRQ of the PSC */
+ irq = irq_of_parse_and_map(op->node, 0);
+ if (of_address_to_resource(op->node, 0, &res)) {
+ dev_err(&op->dev, "Missing reg property\n");
+ return -ENODEV;
+ }
+ regs = ioremap(res.start, 1 + res.end - res.start);
+ if (!regs) {
+ dev_err(&op->dev, "Could not map registers\n");
+ return -ENODEV;
+ }
+
+ /* Allocate and initialize the driver private data */
+ psc_dma = kzalloc(sizeof *psc_dma, GFP_KERNEL);
+ if (!psc_dma) {
+ iounmap(regs);
+ return -ENOMEM;
+ }
+
+ /* Get the PSC ID */
+ prop = of_get_property(op->node, "cell-index", &size);
+ if (!prop || size < sizeof *prop)
+ return -ENODEV;
+
+ spin_lock_init(&psc_dma->lock);
+ psc_dma->id = be32_to_cpu(*prop);
+ psc_dma->irq = irq;
+ psc_dma->psc_regs = regs;
+ psc_dma->fifo_regs = regs + sizeof *psc_dma->psc_regs;
+ psc_dma->dev = &op->dev;
+ psc_dma->playback.psc_dma = psc_dma;
+ psc_dma->capture.psc_dma = psc_dma;
+ snprintf(psc_dma->name, sizeof psc_dma->name, "PSC%u", psc_dma->id);
+
+ /* Find the address of the fifo data registers and setup the
+ * DMA tasks */
+ fifo = res.start + offsetof(struct mpc52xx_psc, buffer.buffer_32);
+ psc_dma->capture.bcom_task =
+ bcom_psc_gen_bd_rx_init(psc_dma->id, 10, fifo, 512);
+ psc_dma->playback.bcom_task =
+ bcom_psc_gen_bd_tx_init(psc_dma->id, 10, fifo);
+ if (!psc_dma->capture.bcom_task ||
+ !psc_dma->playback.bcom_task) {
+ dev_err(&op->dev, "Could not allocate bestcomm tasks\n");
+ iounmap(regs);
+ kfree(psc_dma);
+ return -ENODEV;
+ }
+
+ /* Disable all interrupts and reset the PSC */
+ out_be16(&psc_dma->psc_regs->isr_imr.imr, psc_dma->imr);
+ /* reset receiver */
+ out_8(&psc_dma->psc_regs->command, MPC52xx_PSC_RST_RX);
+ /* reset transmitter */
+ out_8(&psc_dma->psc_regs->command, MPC52xx_PSC_RST_TX);
+ /* reset error */
+ out_8(&psc_dma->psc_regs->command, MPC52xx_PSC_RST_ERR_STAT);
+ /* reset mode */
+ out_8(&psc_dma->psc_regs->command, MPC52xx_PSC_SEL_MODE_REG_1);
+
+ /* Set up mode register;
+ * First write: RxRdy (FIFO Alarm) generates rx FIFO irq
+ * Second write: register Normal mode for non loopback
+ */
+ out_8(&psc_dma->psc_regs->mode, 0);
+ out_8(&psc_dma->psc_regs->mode, 0);
+
+ /* Set the TX and RX fifo alarm thresholds */
+ out_be16(&psc_dma->fifo_regs->rfalarm, 0x100);
+ out_8(&psc_dma->fifo_regs->rfcntl, 0x4);
+ out_be16(&psc_dma->fifo_regs->tfalarm, 0x100);
+ out_8(&psc_dma->fifo_regs->tfcntl, 0x7);
+
+ /* Lookup the IRQ numbers */
+ psc_dma->playback.irq =
+ bcom_get_task_irq(psc_dma->playback.bcom_task);
+ psc_dma->capture.irq =
+ bcom_get_task_irq(psc_dma->capture.bcom_task);
+
+ rc = request_irq(psc_dma->irq, &psc_dma_status_irq, IRQF_SHARED,
+ "psc-dma-status", psc_dma);
+ rc |= request_irq(psc_dma->capture.irq,
+ &psc_dma_bcom_irq_rx, IRQF_SHARED,
+ "psc-dma-capture", &psc_dma->capture);
+ rc |= request_irq(psc_dma->playback.irq,
+ &psc_dma_bcom_irq_tx, IRQF_SHARED,
+ "psc-dma-playback", &psc_dma->playback);
+ if (rc) {
+ free_irq(psc_dma->irq, psc_dma);
+ free_irq(psc_dma->capture.irq,
+ &psc_dma->capture);
+ free_irq(psc_dma->playback.irq,
+ &psc_dma->playback);
+ return -ENODEV;
+ }
+
+ /* Save what we've done so it can be found again later */
+ dev_set_drvdata(&op->dev, psc_dma);
+
+ /* Register the SYSFS files */
+ rc = device_create_file(psc_dma->dev, &dev_attr_status);
+ rc |= device_create_file(psc_dma->dev, &dev_attr_capture_overrun);
+ rc |= device_create_file(psc_dma->dev, &dev_attr_playback_underrun);
+ if (rc)
+ dev_info(psc_dma->dev, "error creating sysfs files\n");
+
+ /* Tell the ASoC OF helpers about it */
+ return snd_soc_register_platform(&mpc5200_audio_dma_platform);
+}
+EXPORT_SYMBOL_GPL(mpc5200_audio_dma_create);
+
+int mpc5200_audio_dma_destroy(struct of_device *op)
+{
+ struct psc_dma *psc_dma = dev_get_drvdata(&op->dev);
+
+ dev_dbg(&op->dev, "mpc5200_audio_dma_destroy()\n");
+
+ snd_soc_unregister_platform(&mpc5200_audio_dma_platform);
+
+ bcom_gen_bd_rx_release(psc_dma->capture.bcom_task);
+ bcom_gen_bd_tx_release(psc_dma->playback.bcom_task);
+
+ /* Release irqs */
+ free_irq(psc_dma->irq, psc_dma);
+ free_irq(psc_dma->capture.irq, &psc_dma->capture);
+ free_irq(psc_dma->playback.irq, &psc_dma->playback);
+
+ iounmap(psc_dma->psc_regs);
+ kfree(psc_dma);
+ dev_set_drvdata(&op->dev, NULL);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(mpc5200_audio_dma_destroy);
+
+MODULE_AUTHOR("Grant Likely <grant.likely@secretlab.ca>");
+MODULE_DESCRIPTION("Freescale MPC5200 PSC in DMA mode ASoC Driver");
+MODULE_LICENSE("GPL");
diff --git a/sound/soc/fsl/mpc5200_dma.h b/sound/soc/fsl/mpc5200_dma.h
index a33232c..2000803 100644
--- a/sound/soc/fsl/mpc5200_dma.h
+++ b/sound/soc/fsl/mpc5200_dma.h
@@ -5,8 +5,10 @@
#ifndef __SOUND_SOC_FSL_MPC5200_DMA_H__
#define __SOUND_SOC_FSL_MPC5200_DMA_H__
+#define PSC_STREAM_NAME_LEN 32
+
/**
- * psc_dma_stream - Data specific to a single stream (playback or capture)
+ * psc_ac97_stream - Data specific to a single stream (playback or capture)
* @active: flag indicating if the stream is active
* @psc_dma: pointer back to parent psc_dma data structure
* @bcom_task: bestcomm task structure
@@ -17,6 +19,9 @@
* @period_bytes: size of DMA period in bytes
*/
struct psc_dma_stream {
+ struct snd_pcm_runtime *runtime;
+ snd_pcm_uframes_t appl_ptr;
+
int active;
struct psc_dma *psc_dma;
struct bcom_task *bcom_task;
@@ -27,6 +32,7 @@ struct psc_dma_stream {
dma_addr_t period_next_pt;
dma_addr_t period_current_pt;
int period_bytes;
+ int period_size;
};
/**
@@ -48,9 +54,12 @@ struct psc_dma {
struct mpc52xx_psc_fifo __iomem *fifo_regs;
unsigned int irq;
struct device *dev;
- struct snd_soc_dai dai;
spinlock_t lock;
u32 sicr;
+ uint sysclk;
+ int imr;
+ int id;
+ unsigned int slots;
/* per-stream data */
struct psc_dma_stream playback;
@@ -58,24 +67,14 @@ struct psc_dma {
/* Statistics */
struct {
- int overrun_count;
- int underrun_count;
+ unsigned long overrun_count;
+ unsigned long underrun_count;
} stats;
};
+int mpc5200_audio_dma_create(struct of_device *op);
+int mpc5200_audio_dma_destroy(struct of_device *op);
-int psc_dma_startup(struct snd_pcm_substream *substream,
- struct snd_soc_dai *dai);
-
-int psc_dma_hw_free(struct snd_pcm_substream *substream,
- struct snd_soc_dai *dai);
-
-void psc_dma_shutdown(struct snd_pcm_substream *substream,
- struct snd_soc_dai *dai);
-
-int psc_dma_trigger(struct snd_pcm_substream *substream, int cmd,
- struct snd_soc_dai *dai);
-
-extern struct snd_soc_platform psc_dma_pcm_soc_platform;
+extern struct snd_soc_platform mpc5200_audio_dma_platform;
#endif /* __SOUND_SOC_FSL_MPC5200_DMA_H__ */
diff --git a/sound/soc/fsl/mpc5200_psc_i2s.c b/sound/soc/fsl/mpc5200_psc_i2s.c
index 12a7917..ce8de90 100644
--- a/sound/soc/fsl/mpc5200_psc_i2s.c
+++ b/sound/soc/fsl/mpc5200_psc_i2s.c
@@ -3,34 +3,22 @@
* ALSA SoC Digital Audio Interface (DAI) driver
*
* Copyright (C) 2008 Secret Lab Technologies Ltd.
+ * Copyright (C) 2009 Jon Smirl, Digispeaker
*/
-#include <linux/init.h>
#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/device.h>
-#include <linux/delay.h>
#include <linux/of_device.h>
#include <linux/of_platform.h>
-#include <linux/dma-mapping.h>
-#include <sound/core.h>
#include <sound/pcm.h>
#include <sound/pcm_params.h>
-#include <sound/initval.h>
#include <sound/soc.h>
-#include <sound/soc-of-simple.h>
-#include <sysdev/bestcomm/bestcomm.h>
-#include <sysdev/bestcomm/gen_bd.h>
#include <asm/mpc52xx_psc.h>
+#include "mpc5200_psc_i2s.h"
#include "mpc5200_dma.h"
-MODULE_AUTHOR("Grant Likely <grant.likely@secretlab.ca>");
-MODULE_DESCRIPTION("Freescale MPC5200 PSC in I2S mode ASoC Driver");
-MODULE_LICENSE("GPL");
-
/**
* PSC_I2S_RATES: sample rates supported by the I2S
*
@@ -46,8 +34,7 @@ MODULE_LICENSE("GPL");
* PSC_I2S_FORMATS: audio formats supported by the PSC I2S mode
*/
#define PSC_I2S_FORMATS (SNDRV_PCM_FMTBIT_S8 | SNDRV_PCM_FMTBIT_S16_BE | \
- SNDRV_PCM_FMTBIT_S24_BE | SNDRV_PCM_FMTBIT_S24_BE | \
- SNDRV_PCM_FMTBIT_S32_BE)
+ SNDRV_PCM_FMTBIT_S24_BE | SNDRV_PCM_FMTBIT_S32_BE)
static int psc_i2s_hw_params(struct snd_pcm_substream *substream,
struct snd_pcm_hw_params *params,
@@ -82,8 +69,6 @@ static int psc_i2s_hw_params(struct snd_pcm_substream *substream,
}
out_be32(&psc_dma->psc_regs->sicr, psc_dma->sicr | mode);
- snd_pcm_set_runtime_buffer(substream, &substream->dma_buffer);
-
return 0;
}
@@ -140,16 +125,13 @@ static int psc_i2s_set_fmt(struct snd_soc_dai *cpu_dai, unsigned int format)
* psc_i2s_dai_template: template CPU Digital Audio Interface
*/
static struct snd_soc_dai_ops psc_i2s_dai_ops = {
- .startup = psc_dma_startup,
.hw_params = psc_i2s_hw_params,
- .hw_free = psc_dma_hw_free,
- .shutdown = psc_dma_shutdown,
- .trigger = psc_dma_trigger,
.set_sysclk = psc_i2s_set_sysclk,
.set_fmt = psc_i2s_set_fmt,
};
-static struct snd_soc_dai psc_i2s_dai_template = {
+struct snd_soc_dai psc_i2s_dai[] = {{
+ .name = "I2S",
.playback = {
.channels_min = 2,
.channels_max = 2,
@@ -163,71 +145,8 @@ static struct snd_soc_dai psc_i2s_dai_template = {
.formats = PSC_I2S_FORMATS,
},
.ops = &psc_i2s_dai_ops,
-};
-
-/* ---------------------------------------------------------------------
- * Sysfs attributes for debugging
- */
-
-static ssize_t psc_i2s_status_show(struct device *dev,
- struct device_attribute *attr, char *buf)
-{
- struct psc_dma *psc_dma = dev_get_drvdata(dev);
-
- return sprintf(buf, "status=%.4x sicr=%.8x rfnum=%i rfstat=0x%.4x "
- "tfnum=%i tfstat=0x%.4x\n",
- in_be16(&psc_dma->psc_regs->sr_csr.status),
- in_be32(&psc_dma->psc_regs->sicr),
- in_be16(&psc_dma->fifo_regs->rfnum) & 0x1ff,
- in_be16(&psc_dma->fifo_regs->rfstat),
- in_be16(&psc_dma->fifo_regs->tfnum) & 0x1ff,
- in_be16(&psc_dma->fifo_regs->tfstat));
-}
-
-static int *psc_i2s_get_stat_attr(struct psc_dma *psc_dma, const char *name)
-{
- if (strcmp(name, "playback_underrun") == 0)
- return &psc_dma->stats.underrun_count;
- if (strcmp(name, "capture_overrun") == 0)
- return &psc_dma->stats.overrun_count;
-
- return NULL;
-}
-
-static ssize_t psc_i2s_stat_show(struct device *dev,
- struct device_attribute *attr, char *buf)
-{
- struct psc_dma *psc_dma = dev_get_drvdata(dev);
- int *attrib;
-
- attrib = psc_i2s_get_stat_attr(psc_dma, attr->attr.name);
- if (!attrib)
- return 0;
-
- return sprintf(buf, "%i\n", *attrib);
-}
-
-static ssize_t psc_i2s_stat_store(struct device *dev,
- struct device_attribute *attr,
- const char *buf,
- size_t count)
-{
- struct psc_dma *psc_dma = dev_get_drvdata(dev);
- int *attrib;
-
- attrib = psc_i2s_get_stat_attr(psc_dma, attr->attr.name);
- if (!attrib)
- return 0;
-
- *attrib = simple_strtoul(buf, NULL, 0);
- return count;
-}
-
-static DEVICE_ATTR(status, 0644, psc_i2s_status_show, NULL);
-static DEVICE_ATTR(playback_underrun, 0644, psc_i2s_stat_show,
- psc_i2s_stat_store);
-static DEVICE_ATTR(capture_overrun, 0644, psc_i2s_stat_show,
- psc_i2s_stat_store);
+} };
+EXPORT_SYMBOL_GPL(psc_i2s_dai);
/* ---------------------------------------------------------------------
* OF platform bus binding code:
@@ -237,82 +156,26 @@ static DEVICE_ATTR(capture_overrun, 0644, psc_i2s_stat_show,
static int __devinit psc_i2s_of_probe(struct of_device *op,
const struct of_device_id *match)
{
- phys_addr_t fifo;
+ int rc;
struct psc_dma *psc_dma;
- struct resource res;
- int size, psc_id, irq, rc;
- const __be32 *prop;
- void __iomem *regs;
-
- dev_dbg(&op->dev, "probing psc i2s device\n");
-
- /* Get the PSC ID */
- prop = of_get_property(op->node, "cell-index", &size);
- if (!prop || size < sizeof *prop)
- return -ENODEV;
- psc_id = be32_to_cpu(*prop);
-
- /* Fetch the registers and IRQ of the PSC */
- irq = irq_of_parse_and_map(op->node, 0);
- if (of_address_to_resource(op->node, 0, &res)) {
- dev_err(&op->dev, "Missing reg property\n");
- return -ENODEV;
- }
- regs = ioremap(res.start, 1 + res.end - res.start);
- if (!regs) {
- dev_err(&op->dev, "Could not map registers\n");
- return -ENODEV;
- }
+ struct mpc52xx_psc __iomem *regs;
- /* Allocate and initialize the driver private data */
- psc_dma = kzalloc(sizeof *psc_dma, GFP_KERNEL);
- if (!psc_dma) {
- iounmap(regs);
- return -ENOMEM;
- }
- spin_lock_init(&psc_dma->lock);
- psc_dma->irq = irq;
- psc_dma->psc_regs = regs;
- psc_dma->fifo_regs = regs + sizeof *psc_dma->psc_regs;
- psc_dma->dev = &op->dev;
- psc_dma->playback.psc_dma = psc_dma;
- psc_dma->capture.psc_dma = psc_dma;
- snprintf(psc_dma->name, sizeof psc_dma->name, "PSC%u", psc_id+1);
-
- /* Fill out the CPU DAI structure */
- memcpy(&psc_dma->dai, &psc_i2s_dai_template, sizeof psc_dma->dai);
- psc_dma->dai.private_data = psc_dma;
- psc_dma->dai.name = psc_dma->name;
- psc_dma->dai.id = psc_id;
-
- /* Find the address of the fifo data registers and setup the
- * DMA tasks */
- fifo = res.start + offsetof(struct mpc52xx_psc, buffer.buffer_32);
- psc_dma->capture.bcom_task =
- bcom_psc_gen_bd_rx_init(psc_id, 10, fifo, 512);
- psc_dma->playback.bcom_task =
- bcom_psc_gen_bd_tx_init(psc_id, 10, fifo);
- if (!psc_dma->capture.bcom_task ||
- !psc_dma->playback.bcom_task) {
- dev_err(&op->dev, "Could not allocate bestcomm tasks\n");
- iounmap(regs);
- kfree(psc_dma);
- return -ENODEV;
+ rc = mpc5200_audio_dma_create(op);
+ if (rc != 0)
+ return rc;
+
+ rc = snd_soc_register_dais(psc_i2s_dai, ARRAY_SIZE(psc_i2s_dai));
+ if (rc != 0) {
+ pr_err("Failed to register DAI\n");
+ return 0;
}
- /* Disable all interrupts and reset the PSC */
- out_be16(&psc_dma->psc_regs->isr_imr.imr, 0);
- out_8(&psc_dma->psc_regs->command, 3 << 4); /* reset transmitter */
- out_8(&psc_dma->psc_regs->command, 2 << 4); /* reset receiver */
- out_8(&psc_dma->psc_regs->command, 1 << 4); /* reset mode */
- out_8(&psc_dma->psc_regs->command, 4 << 4); /* reset error */
+ psc_dma = dev_get_drvdata(&op->dev);
+ regs = psc_dma->psc_regs;
/* Configure the serial interface mode; defaulting to CODEC8 mode */
psc_dma->sicr = MPC52xx_PSC_SICR_DTS1 | MPC52xx_PSC_SICR_I2S |
MPC52xx_PSC_SICR_CLKPOL;
- if (of_get_property(op->node, "fsl,cellslave", NULL))
- psc_dma->sicr |= MPC52xx_PSC_SICR_CELLSLAVE |
- MPC52xx_PSC_SICR_GENCLK;
out_be32(&psc_dma->psc_regs->sicr,
psc_dma->sicr | MPC52xx_PSC_SICR_SIM_CODEC_8);
@@ -321,66 +184,37 @@ static int __devinit psc_i2s_of_probe(struct of_device *op,
if (!of_get_property(op->node, "codec-handle", NULL))
return 0;
- /* Set up mode register;
- * First write: RxRdy (FIFO Alarm) generates rx FIFO irq
- * Second write: register Normal mode for non loopback
- */
- out_8(&psc_dma->psc_regs->mode, 0);
- out_8(&psc_dma->psc_regs->mode, 0);
-
- /* Set the TX and RX fifo alarm thresholds */
- out_be16(&psc_dma->fifo_regs->rfalarm, 0x100);
- out_8(&psc_dma->fifo_regs->rfcntl, 0x4);
- out_be16(&psc_dma->fifo_regs->tfalarm, 0x100);
- out_8(&psc_dma->fifo_regs->tfcntl, 0x7);
-
- /* Lookup the IRQ numbers */
- psc_dma->playback.irq =
- bcom_get_task_irq(psc_dma->playback.bcom_task);
- psc_dma->capture.irq =
- bcom_get_task_irq(psc_dma->capture.bcom_task);
-
- /* Save what we've done so it can be found again later */
- dev_set_drvdata(&op->dev, psc_dma);
-
- /* Register the SYSFS files */
- rc = device_create_file(psc_dma->dev, &dev_attr_status);
- rc |= device_create_file(psc_dma->dev, &dev_attr_capture_overrun);
- rc |= device_create_file(psc_dma->dev, &dev_attr_playback_underrun);
- if (rc)
- dev_info(psc_dma->dev, "error creating sysfs files\n");
-
- snd_soc_register_platform(&psc_dma_pcm_soc_platform);
-
- /* Tell the ASoC OF helpers about it */
- of_snd_soc_register_platform(&psc_dma_pcm_soc_platform, op->node,
- &psc_dma->dai);
+ /* Due to errata in the dma mode; need to line up enabling
+ * the transmitter with a transition on the frame sync
+ * line */
+
+ /* first make sure it is low */
+ while ((in_8(®s->ipcr_acr.ipcr) & 0x80) != 0)
+ ;
+ /* then wait for the transition to high */
+ while ((in_8(®s->ipcr_acr.ipcr) & 0x80) == 0)
+ ;
+ /* Finally, enable the PSC.
+ * Receiver must always be enabled; even when we only want
+ * transmit. (see 15.3.2.3 of MPC5200B User's Guide) */
+
+ /* Go */
+ out_8(&psc_dma->psc_regs->command,
+ MPC52xx_PSC_TX_ENABLE | MPC52xx_PSC_RX_ENABLE);
return 0;
+
}
static int __devexit psc_i2s_of_remove(struct of_device *op)
{
- struct psc_dma *psc_dma = dev_get_drvdata(&op->dev);
-
- dev_dbg(&op->dev, "psc_i2s_remove()\n");
-
- snd_soc_unregister_platform(&psc_dma_pcm_soc_platform);
-
- bcom_gen_bd_rx_release(psc_dma->capture.bcom_task);
- bcom_gen_bd_tx_release(psc_dma->playback.bcom_task);
-
- iounmap(psc_dma->psc_regs);
- iounmap(psc_dma->fifo_regs);
- kfree(psc_dma);
- dev_set_drvdata(&op->dev, NULL);
-
- return 0;
+ return mpc5200_audio_dma_destroy(op);
}
/* Match table for of_platform binding */
static struct of_device_id psc_i2s_match[] __devinitdata = {
{ .compatible = "fsl,mpc5200-psc-i2s", },
+ { .compatible = "fsl,mpc5200b-psc-i2s", },
{}
};
MODULE_DEVICE_TABLE(of, psc_i2s_match);
@@ -411,4 +245,7 @@ static void __exit psc_i2s_exit(void)
}
module_exit(psc_i2s_exit);
+MODULE_AUTHOR("Grant Likely <grant.likely@secretlab.ca>");
+MODULE_DESCRIPTION("Freescale MPC5200 PSC in I2S mode ASoC Driver");
+MODULE_LICENSE("GPL");
diff --git a/sound/soc/fsl/mpc5200_psc_i2s.h b/sound/soc/fsl/mpc5200_psc_i2s.h
new file mode 100644
index 0000000..ce55e07
--- /dev/null
+++ b/sound/soc/fsl/mpc5200_psc_i2s.h
@@ -0,0 +1,12 @@
+/*
+ * Freescale MPC5200 PSC in I2S mode
+ * ALSA SoC Digital Audio Interface (DAI) driver
+ *
+ */
+
+#ifndef __SOUND_SOC_FSL_MPC52xx_PSC_I2S_H__
+#define __SOUND_SOC_FSL_MPC52xx_PSC_I2S_H__
+
+extern struct snd_soc_dai psc_i2s_dai[];
+
+#endif /* __SOUND_SOC_FSL_MPC52xx_PSC_I2S_H__ */
^ permalink raw reply related
* [PATCH V3 2/4] AC97 driver for mpc5200
From: Jon Smirl @ 2009-05-25 1:38 UTC (permalink / raw)
To: grant.likely, linuxppc-dev, alsa-devel, broonie
In-Reply-To: <20090525013606.3073.86753.stgit@terra>
AC97 driver for mpc5200
I've implemented retries for when the AC97 hardware doesn't reset on
first try. About 10% of the time both the Efika and pcm030 AC97 codecs
don't reset on first try and need to be poked multiple times. Failure
is indicated by not having the link clock start ticking. Every once in
a while even five pokes won't get the link started and I have to power
cycle.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
---
sound/soc/fsl/Kconfig | 11 +
sound/soc/fsl/Makefile | 1
sound/soc/fsl/mpc5200_psc_ac97.c | 392 ++++++++++++++++++++++++++++++++++++++
sound/soc/fsl/mpc5200_psc_ac97.h | 15 +
4 files changed, 419 insertions(+), 0 deletions(-)
create mode 100644 sound/soc/fsl/mpc5200_psc_ac97.c
create mode 100644 sound/soc/fsl/mpc5200_psc_ac97.h
diff --git a/sound/soc/fsl/Kconfig b/sound/soc/fsl/Kconfig
index 1918c78..3bce952 100644
--- a/sound/soc/fsl/Kconfig
+++ b/sound/soc/fsl/Kconfig
@@ -29,3 +29,14 @@ config SND_SOC_MPC5200_I2S
select PPC_BESTCOMM_GEN_BD
help
Say Y here to support the MPC5200 PSCs in I2S mode.
+
+config SND_SOC_MPC5200_AC97
+ tristate "Freescale MPC5200 PSC in AC97 mode driver"
+ depends on PPC_MPC52xx && PPC_BESTCOMM
+ select AC97_BUS
+ select SND_MPC52xx_DMA
+ select PPC_BESTCOMM_GEN_BD
+ help
+ Say Y here to support the MPC5200 PSCs in AC97 mode.
+
+
diff --git a/sound/soc/fsl/Makefile b/sound/soc/fsl/Makefile
index 7731ef2..14631a1 100644
--- a/sound/soc/fsl/Makefile
+++ b/sound/soc/fsl/Makefile
@@ -13,4 +13,5 @@ obj-$(CONFIG_SND_SOC_MPC8610) += snd-soc-fsl-ssi.o snd-soc-fsl-dma.o
# MPC5200 Platform Support
obj-$(CONFIG_SND_MPC52xx_DMA) += mpc5200_dma.o
obj-$(CONFIG_SND_SOC_MPC5200_I2S) += mpc5200_psc_i2s.o
+obj-$(CONFIG_SND_SOC_MPC5200_AC97) += mpc5200_psc_ac97.o
diff --git a/sound/soc/fsl/mpc5200_psc_ac97.c b/sound/soc/fsl/mpc5200_psc_ac97.c
new file mode 100644
index 0000000..480b677
--- /dev/null
+++ b/sound/soc/fsl/mpc5200_psc_ac97.c
@@ -0,0 +1,392 @@
+/*
+ * linux/sound/mpc5200-ac97.c -- AC97 support for the Freescale MPC52xx chip.
+ *
+ * Copyright (C) 2009 Jon Smirl, Digispeaker
+ * Author: Jon Smirl <jonsmirl@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+
+#include <sound/pcm.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
+
+#include <asm/mpc52xx_psc.h>
+
+#include "mpc5200_dma.h"
+#include "mpc5200_psc_ac97.h"
+
+#define DRV_NAME "mpc5200-psc-ac97"
+
+/* ALSA only supports a single AC97 device so static is recommend here */
+static struct psc_dma *psc_dma;
+
+static unsigned short psc_ac97_read(struct snd_ac97 *ac97, unsigned short reg)
+{
+ int timeout;
+ unsigned int val;
+
+ spin_lock(&psc_dma->lock);
+
+ /* Wait for it to be ready */
+ timeout = 1000;
+ while ((--timeout) && (in_be16(&psc_dma->psc_regs->sr_csr.status) &
+ MPC52xx_PSC_SR_CMDSEND))
+ udelay(10);
+
+ if (!timeout) {
+ pr_err("timeout on ac97 bus (rdy)\n");
+ return 0xffff;
+ }
+
+ /* Do the read */
+ out_be32(&psc_dma->psc_regs->ac97_cmd, (1<<31) | ((reg & 0x7f) << 24));
+
+ /* Wait for the answer */
+ timeout = 1000;
+ while ((--timeout) && !(in_be16(&psc_dma->psc_regs->sr_csr.status) &
+ MPC52xx_PSC_SR_DATA_VAL))
+ udelay(10);
+
+ if (!timeout) {
+ pr_err("timeout on ac97 read (val) %x\n",
+ in_be16(&psc_dma->psc_regs->sr_csr.status));
+ return 0xffff;
+ }
+
+ /* Get the data */
+ val = in_be32(&psc_dma->psc_regs->ac97_data);
+ if (((val>>24) & 0x7f) != reg) {
+ pr_err("reg echo error on ac97 read\n");
+ return 0xffff;
+ }
+ val = (val >> 8) & 0xffff;
+
+ spin_unlock(&psc_dma->lock);
+ return (unsigned short) val;
+}
+
+static void psc_ac97_write(struct snd_ac97 *ac97,
+ unsigned short reg, unsigned short val)
+{
+ int timeout;
+
+ spin_lock(&psc_dma->lock);
+
+ /* Wait for it to be ready */
+ timeout = 1000;
+ while ((--timeout) && (in_be16(&psc_dma->psc_regs->sr_csr.status) &
+ MPC52xx_PSC_SR_CMDSEND))
+ udelay(10);
+
+ if (!timeout) {
+ pr_err("timeout on ac97 write\n");
+ return;
+ }
+
+ /* Write data */
+ out_be32(&psc_dma->psc_regs->ac97_cmd,
+ ((reg & 0x7f) << 24) | (val << 8));
+
+ spin_unlock(&psc_dma->lock);
+}
+
+static void psc_ac97_warm_reset(struct snd_ac97 *ac97)
+{
+ struct mpc52xx_psc __iomem *regs = psc_dma->psc_regs;
+
+ out_be32(®s->sicr, psc_dma->sicr | MPC52xx_PSC_SICR_AWR);
+ udelay(3);
+ out_be32(®s->sicr, psc_dma->sicr);
+}
+
+static int psc_ac97_cold_reset_check(struct snd_ac97 *ac97)
+{
+ int max_reset, timeout;
+ struct mpc52xx_psc __iomem *regs = psc_dma->psc_regs;
+
+ /* AC97 clock is generated by the codec.
+ * Ensure that it starts ticking after codec reset.
+ */
+ for (max_reset = 0; max_reset < 5; max_reset++) {
+
+ /* Do a cold reset */
+ out_8(®s->op1, MPC52xx_PSC_OP_RES);
+ udelay(10);
+ out_8(®s->op0, MPC52xx_PSC_OP_RES);
+ udelay(50);
+
+ /* PSC recover from cold reset
+ * (cfr user manual, not sure if useful)
+ */
+ out_be32(®s->sicr, in_be32(®s->sicr));
+
+ psc_ac97_warm_reset(ac97);
+
+ /* first make sure AC97 clock is low */
+ for (timeout = 0; ((in_8(®s->ipcr_acr.ipcr) & 0x80) != 0) &&
+ (timeout < 100); timeout++)
+ udelay(10);
+ if (timeout == 100)
+ continue;
+
+ /* then wait for the transition to high */
+ for (timeout = 0; ((in_8(®s->ipcr_acr.ipcr) & 0x80) == 0) &&
+ (timeout < 100); timeout++)
+ udelay(10);
+ if (timeout == 100)
+ continue;
+
+ break;
+ }
+ if (max_reset == 5)
+ return -ENODEV;
+ return 0;
+}
+
+static void psc_ac97_cold_reset(struct snd_ac97 *ac97)
+{
+ psc_ac97_cold_reset_check(ac97);
+
+}
+
+struct snd_ac97_bus_ops soc_ac97_ops = {
+ .read = psc_ac97_read,
+ .write = psc_ac97_write,
+ .reset = psc_ac97_cold_reset,
+ .warm_reset = psc_ac97_warm_reset,
+};
+EXPORT_SYMBOL_GPL(soc_ac97_ops);
+
+static int psc_ac97_hw_analog_params(struct snd_pcm_substream *substream,
+ struct snd_pcm_hw_params *params,
+ struct snd_soc_dai *cpu_dai)
+{
+ struct psc_dma *psc_dma = cpu_dai->private_data;
+
+ dev_dbg(psc_dma->dev, "%s(substream=%p) p_size=%i p_bytes=%i"
+ " periods=%i buffer_size=%i buffer_bytes=%i channels=%i"
+ " rate=%i format=%i\n",
+ __func__, substream, params_period_size(params),
+ params_period_bytes(params), params_periods(params),
+ params_buffer_size(params), params_buffer_bytes(params),
+ params_channels(params), params_rate(params),
+ params_format(params));
+
+
+ if (substream->pstr->stream == SNDRV_PCM_STREAM_CAPTURE) {
+ if (params_channels(params) == 1)
+ psc_dma->slots |= 0x00000100;
+ else
+ psc_dma->slots |= 0x00000300;
+ } else {
+ if (params_channels(params) == 1)
+ psc_dma->slots |= 0x01000000;
+ else
+ psc_dma->slots |= 0x03000000;
+ }
+
+ spin_lock(&psc_dma->lock);
+ out_be32(&psc_dma->psc_regs->ac97_slots, psc_dma->slots);
+ spin_unlock(&psc_dma->lock);
+
+ return 0;
+}
+
+static int psc_ac97_hw_digital_params(struct snd_pcm_substream *substream,
+ struct snd_pcm_hw_params *params,
+ struct snd_soc_dai *cpu_dai)
+{
+ struct psc_dma *psc_dma = cpu_dai->private_data;
+
+ spin_lock(&psc_dma->lock);
+ if (params_channels(params) == 1)
+ out_be32(&psc_dma->psc_regs->ac97_slots, 0x01000000);
+ else
+ out_be32(&psc_dma->psc_regs->ac97_slots, 0x03000000);
+ spin_unlock(&psc_dma->lock);
+
+ return 0;
+}
+
+static int psc_ac97_trigger(struct snd_pcm_substream *substream, int cmd,
+ struct snd_soc_dai *dai)
+{
+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
+ struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data;
+
+ switch (cmd) {
+ case SNDRV_PCM_TRIGGER_STOP:
+ if (substream->pstr->stream == SNDRV_PCM_STREAM_CAPTURE)
+ psc_dma->slots &= 0xFFFF0000;
+ else
+ psc_dma->slots &= 0x0000FFFF;
+
+ spin_lock(&psc_dma->lock);
+ out_be32(&psc_dma->psc_regs->ac97_slots, psc_dma->slots);
+ spin_unlock(&psc_dma->lock);
+ break;
+ }
+ return 0;
+}
+
+/* ---------------------------------------------------------------------
+ * ALSA SoC Bindings
+ *
+ * - Digital Audio Interface (DAI) template
+ * - create/destroy dai hooks
+ */
+
+/**
+ * psc_ac97_dai_template: template CPU Digital Audio Interface
+ */
+static struct snd_soc_dai_ops psc_ac97_analog_ops = {
+ .hw_params = psc_ac97_hw_analog_params,
+ .trigger = psc_ac97_trigger,
+};
+
+static struct snd_soc_dai_ops psc_ac97_digital_ops = {
+ .hw_params = psc_ac97_hw_digital_params,
+};
+
+struct snd_soc_dai psc_ac97_dai[] = {
+{
+ .name = "AC97",
+ .ac97_control = 1,
+ .playback = {
+ .channels_min = 1,
+ .channels_max = 6,
+ .rates = SNDRV_PCM_RATE_8000_48000,
+ .formats = SNDRV_PCM_FMTBIT_S32_BE,
+ },
+ .capture = {
+ .channels_min = 1,
+ .channels_max = 2,
+ .rates = SNDRV_PCM_RATE_8000_48000,
+ .formats = SNDRV_PCM_FMTBIT_S32_BE,
+ },
+ .ops = &psc_ac97_analog_ops,
+},
+{
+ .name = "SPDIF",
+ .ac97_control = 1,
+ .playback = {
+ .channels_min = 1,
+ .channels_max = 2,
+ .rates = SNDRV_PCM_RATE_32000 | \
+ SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000,
+ .formats = SNDRV_PCM_FMTBIT_IEC958_SUBFRAME_BE,
+ },
+ .ops = &psc_ac97_digital_ops,
+} };
+EXPORT_SYMBOL_GPL(psc_ac97_dai);
+
+
+
+/* ---------------------------------------------------------------------
+ * OF platform bus binding code:
+ * - Probe/remove operations
+ * - OF device match table
+ */
+static int __devinit psc_ac97_of_probe(struct of_device *op,
+ const struct of_device_id *match)
+{
+ int rc, i, id1, id2;
+ struct snd_ac97 ac97;
+ struct mpc52xx_psc __iomem *regs;
+
+ rc = mpc5200_audio_dma_create(op);
+ if (rc != 0)
+ return rc;
+
+ for (i = 0; i < ARRAY_SIZE(psc_ac97_dai); i++)
+ psc_ac97_dai[i].dev = &op->dev;
+
+ rc = snd_soc_register_dais(psc_ac97_dai, ARRAY_SIZE(psc_ac97_dai));
+ if (rc != 0) {
+ dev_err(&op->dev, "Failed to register DAI\n");
+ return rc;
+ }
+
+ psc_dma = dev_get_drvdata(&op->dev);
+ regs = psc_dma->psc_regs;
+ ac97.private_data = psc_dma;
+
+ for (i = 0; i < ARRAY_SIZE(psc_ac97_dai); i++)
+ psc_ac97_dai[i].private_data = psc_dma;
+
+ psc_dma->imr = 0;
+ out_be16(&psc_dma->psc_regs->isr_imr.imr, psc_dma->imr);
+
+ /* Configure the serial interface mode to AC97 */
+ psc_dma->sicr = MPC52xx_PSC_SICR_SIM_AC97 | MPC52xx_PSC_SICR_ENAC97;
+ out_be32(®s->sicr, psc_dma->sicr);
+
+ /* No slots active */
+ out_be32(®s->ac97_slots, 0x00000000);
+
+ /* AC97 clock is generated by the codec.
+ * Ensure that it starts ticking after codec reset.
+ */
+ rc = psc_ac97_cold_reset_check(&ac97);
+ if (rc != 0) {
+ dev_err(&op->dev, "AC97 codec failed to reset\n");
+ mpc5200_audio_dma_destroy(op);
+ return rc;
+ }
+
+ /* Go */
+ out_8(®s->command, MPC52xx_PSC_TX_ENABLE | MPC52xx_PSC_RX_ENABLE);
+
+ return 0;
+}
+
+static int __devexit psc_ac97_of_remove(struct of_device *op)
+{
+ return mpc5200_audio_dma_destroy(op);
+}
+
+/* Match table for of_platform binding */
+static struct of_device_id psc_ac97_match[] __devinitdata = {
+ { .compatible = "fsl,mpc5200-psc-ac97", },
+ { .compatible = "fsl,mpc5200b-psc-ac97", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, psc_ac97_match);
+
+static struct of_platform_driver psc_ac97_driver = {
+ .match_table = psc_ac97_match,
+ .probe = psc_ac97_of_probe,
+ .remove = __devexit_p(psc_ac97_of_remove),
+ .driver = {
+ .name = "mpc5200-psc-ac97",
+ .owner = THIS_MODULE,
+ },
+};
+
+/* ---------------------------------------------------------------------
+ * Module setup and teardown; simply register the of_platform driver
+ * for the PSC in AC97 mode.
+ */
+static int __init psc_ac97_init(void)
+{
+ return of_register_platform_driver(&psc_ac97_driver);
+}
+module_init(psc_ac97_init);
+
+static void __exit psc_ac97_exit(void)
+{
+ of_unregister_platform_driver(&psc_ac97_driver);
+}
+module_exit(psc_ac97_exit);
+
+MODULE_AUTHOR("Jon Smirl <jonsmirl@gmail.com>");
+MODULE_DESCRIPTION("mpc5200 AC97 module");
+MODULE_LICENSE("GPL");
+
diff --git a/sound/soc/fsl/mpc5200_psc_ac97.h b/sound/soc/fsl/mpc5200_psc_ac97.h
new file mode 100644
index 0000000..4bc18c3
--- /dev/null
+++ b/sound/soc/fsl/mpc5200_psc_ac97.h
@@ -0,0 +1,15 @@
+/*
+ * Freescale MPC5200 PSC in AC97 mode
+ * ALSA SoC Digital Audio Interface (DAI) driver
+ *
+ */
+
+#ifndef __SOUND_SOC_FSL_MPC52xx_PSC_AC97_H__
+#define __SOUND_SOC_FSL_MPC52xx_PSC_AC97_H__
+
+extern struct snd_soc_dai psc_ac97_dai[];
+
+#define MPC5200_AC97_NORMAL 0
+#define MPC5200_AC97_SPDIF 1
+
+#endif /* __SOUND_SOC_FSL_MPC52xx_PSC_AC97_H__ */
^ permalink raw reply related
* [PATCH V3 3/4] Support for AC97 on Phytec pmc030 base board.
From: Jon Smirl @ 2009-05-25 1:38 UTC (permalink / raw)
To: grant.likely, linuxppc-dev, alsa-devel, broonie
In-Reply-To: <20090525013606.3073.86753.stgit@terra>
Support for AC97 on Phytec pmc030 base board. A wm9712 AC97 codec is used.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
---
sound/soc/fsl/Kconfig | 7 +++
sound/soc/fsl/Makefile | 3 +
sound/soc/fsl/pcm030-audio-fabric.c | 95 +++++++++++++++++++++++++++++++++++
3 files changed, 105 insertions(+), 0 deletions(-)
create mode 100644 sound/soc/fsl/pcm030-audio-fabric.c
diff --git a/sound/soc/fsl/Kconfig b/sound/soc/fsl/Kconfig
index 3bce952..79579ae 100644
--- a/sound/soc/fsl/Kconfig
+++ b/sound/soc/fsl/Kconfig
@@ -39,4 +39,11 @@ config SND_SOC_MPC5200_AC97
help
Say Y here to support the MPC5200 PSCs in AC97 mode.
+config SND_MPC52xx_SOC_PCM030
+ tristate "SoC AC97 Audio support for Phytec pcm030 and WM9712"
+ depends on PPC_MPC5200_SIMPLE
+ select SND_SOC_MPC5200_AC97
+ select SND_SOC_WM9712
+ help
+ Say Y if you want to add support for sound on the Phytec pcm030 baseboard.
diff --git a/sound/soc/fsl/Makefile b/sound/soc/fsl/Makefile
index 14631a1..66d88c8 100644
--- a/sound/soc/fsl/Makefile
+++ b/sound/soc/fsl/Makefile
@@ -15,3 +15,6 @@ obj-$(CONFIG_SND_MPC52xx_DMA) += mpc5200_dma.o
obj-$(CONFIG_SND_SOC_MPC5200_I2S) += mpc5200_psc_i2s.o
obj-$(CONFIG_SND_SOC_MPC5200_AC97) += mpc5200_psc_ac97.o
+# MPC5200 Machine Support
+obj-$(CONFIG_SND_MPC52xx_SOC_PCM030) += pcm030-audio-fabric.o
+
diff --git a/sound/soc/fsl/pcm030-audio-fabric.c b/sound/soc/fsl/pcm030-audio-fabric.c
new file mode 100644
index 0000000..2c426d5
--- /dev/null
+++ b/sound/soc/fsl/pcm030-audio-fabric.c
@@ -0,0 +1,95 @@
+/*
+ * Phytec pcm030 driver for the PSC of the Freescale MPC52xx
+ * configured as AC97 interface
+ *
+ * Copyright 2008 Jon Smirl, Digispeaker
+ * Author: Jon Smirl <jonsmirl@gmail.com>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/device.h>
+#include <linux/delay.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+#include <linux/dma-mapping.h>
+
+#include <sound/core.h>
+#include <sound/pcm.h>
+#include <sound/pcm_params.h>
+#include <sound/initval.h>
+#include <sound/soc.h>
+#include <sound/soc-of-simple.h>
+
+#include "mpc5200_dma.h"
+#include "mpc5200_psc_ac97.h"
+#include "../codecs/wm9712.h"
+
+static struct snd_soc_device device;
+static struct snd_soc_card card;
+
+static struct snd_soc_dai_link pcm030_fabric_dai[] = {
+{
+ .name = "AC97",
+ .stream_name = "AC97 Analog",
+ .codec_dai = &wm9712_dai[WM9712_DAI_AC97_HIFI],
+ .cpu_dai = &psc_ac97_dai[MPC5200_AC97_NORMAL],
+},
+{
+ .name = "AC97",
+ .stream_name = "AC97 IEC958",
+ .codec_dai = &wm9712_dai[WM9712_DAI_AC97_AUX],
+ .cpu_dai = &psc_ac97_dai[MPC5200_AC97_SPDIF],
+},
+};
+
+static __init int pcm030_fabric_init(void)
+{
+ struct platform_device *pdev;
+ int rc;
+
+ if (!machine_is_compatible("phytec,pcm030"))
+ return -ENODEV;
+
+ card.platform = &mpc5200_audio_dma_platform;
+ card.name = "pcm030";
+ card.dai_link = pcm030_fabric_dai;
+ card.num_links = ARRAY_SIZE(pcm030_fabric_dai);
+
+ device.card = &card;
+ device.codec_dev = &soc_codec_dev_wm9712;
+
+ pdev = platform_device_alloc("soc-audio", 1);
+ if (!pdev) {
+ pr_err("pcm030_fabric_init: platform_device_alloc() failed\n");
+ return -ENODEV;
+ }
+
+ platform_set_drvdata(pdev, &device);
+ device.dev = &pdev->dev;
+
+ rc = platform_device_add(pdev);
+ if (rc) {
+ pr_err("pcm030_fabric_init: platform_device_add() failed\n");
+ return -ENODEV;
+ }
+ return 0;
+}
+
+static __exit void pcm030_fabric_exit(void)
+{
+}
+
+module_init(pcm030_fabric_init);
+module_exit(pcm030_fabric_exit);
+
+
+MODULE_AUTHOR("Jon Smirl <jonsmirl@gmail.com>");
+MODULE_DESCRIPTION(DRV_NAME ": mpc5200 pcm030 fabric driver");
+MODULE_LICENSE("GPL");
+
^ permalink raw reply related
* [PATCH V3 4/4] Fabric bindings for STAC9766 on the Efika
From: Jon Smirl @ 2009-05-25 1:38 UTC (permalink / raw)
To: grant.likely, linuxppc-dev, alsa-devel, broonie
In-Reply-To: <20090525013606.3073.86753.stgit@terra>
Fabric bindings for STAC9766 AC97 codec on the Efika.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
---
sound/soc/fsl/Kconfig | 8 +++
sound/soc/fsl/Makefile | 1
sound/soc/fsl/efika-audio-fabric.c | 95 ++++++++++++++++++++++++++++++++++++
3 files changed, 104 insertions(+), 0 deletions(-)
create mode 100644 sound/soc/fsl/efika-audio-fabric.c
diff --git a/sound/soc/fsl/Kconfig b/sound/soc/fsl/Kconfig
index 79579ae..f571c6e 100644
--- a/sound/soc/fsl/Kconfig
+++ b/sound/soc/fsl/Kconfig
@@ -47,3 +47,11 @@ config SND_MPC52xx_SOC_PCM030
help
Say Y if you want to add support for sound on the Phytec pcm030 baseboard.
+config SND_MPC52xx_SOC_EFIKA
+ tristate "SoC AC97 Audio support for bbplan Efika and STAC9766"
+ depends on PPC_EFIKA
+ select SND_SOC_MPC5200_AC97
+ select SND_SOC_STAC9766
+ help
+ Say Y if you want to add support for sound on the Efika.
+
diff --git a/sound/soc/fsl/Makefile b/sound/soc/fsl/Makefile
index 66d88c8..a83a739 100644
--- a/sound/soc/fsl/Makefile
+++ b/sound/soc/fsl/Makefile
@@ -17,4 +17,5 @@ obj-$(CONFIG_SND_SOC_MPC5200_AC97) += mpc5200_psc_ac97.o
# MPC5200 Machine Support
obj-$(CONFIG_SND_MPC52xx_SOC_PCM030) += pcm030-audio-fabric.o
+obj-$(CONFIG_SND_MPC52xx_SOC_EFIKA) += efika-audio-fabric.o
diff --git a/sound/soc/fsl/efika-audio-fabric.c b/sound/soc/fsl/efika-audio-fabric.c
new file mode 100644
index 0000000..4b7ed2b
--- /dev/null
+++ b/sound/soc/fsl/efika-audio-fabric.c
@@ -0,0 +1,95 @@
+/*
+ * Efika driver for the PSC of the Freescale MPC52xx
+ * configured as AC97 interface
+ *
+ * Copyright 2008 Jon Smirl, Digispeaker
+ * Author: Jon Smirl <jonsmirl@gmail.com>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/device.h>
+#include <linux/delay.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+#include <linux/dma-mapping.h>
+
+#include <sound/core.h>
+#include <sound/pcm.h>
+#include <sound/pcm_params.h>
+#include <sound/initval.h>
+#include <sound/soc.h>
+#include <sound/soc-of-simple.h>
+
+#include "mpc5200_dma.h"
+#include "mpc5200_psc_ac97.h"
+#include "../codecs/stac9766.h"
+
+static struct snd_soc_device device;
+static struct snd_soc_card card;
+
+static struct snd_soc_dai_link efika_fabric_dai[] = {
+{
+ .name = "AC97",
+ .stream_name = "AC97 Analog",
+ .codec_dai = &stac9766_dai[STAC9766_DAI_AC97_ANALOG],
+ .cpu_dai = &psc_ac97_dai[MPC5200_AC97_NORMAL],
+},
+{
+ .name = "AC97",
+ .stream_name = "AC97 IEC958",
+ .codec_dai = &stac9766_dai[STAC9766_DAI_AC97_DIGITAL],
+ .cpu_dai = &psc_ac97_dai[MPC5200_AC97_SPDIF],
+},
+};
+
+static __init int efika_fabric_init(void)
+{
+ struct platform_device *pdev;
+ int rc;
+
+ if (!machine_is_compatible("bplan,efika"))
+ return -ENODEV;
+
+ card.platform = &mpc5200_audio_dma_platform;
+ card.name = "Efika";
+ card.dai_link = efika_fabric_dai;
+ card.num_links = ARRAY_SIZE(efika_fabric_dai);
+
+ device.card = &card;
+ device.codec_dev = &soc_codec_dev_stac9766;
+
+ pdev = platform_device_alloc("soc-audio", 1);
+ if (!pdev) {
+ pr_err("efika_fabric_init: platform_device_alloc() failed\n");
+ return -ENODEV;
+ }
+
+ platform_set_drvdata(pdev, &device);
+ device.dev = &pdev->dev;
+
+ rc = platform_device_add(pdev);
+ if (rc) {
+ pr_err("efika_fabric_init: platform_device_add() failed\n");
+ return -ENODEV;
+ }
+ return 0;
+}
+
+static __exit void efika_fabric_exit(void)
+{
+}
+
+module_init(efika_fabric_init);
+module_exit(efika_fabric_exit);
+
+
+MODULE_AUTHOR("Jon Smirl <jonsmirl@gmail.com>");
+MODULE_DESCRIPTION(DRV_NAME ": mpc5200 Efika fabric driver");
+MODULE_LICENSE("GPL");
+
^ permalink raw reply related
* Re: powerpc: DMA coherent allocations broken for CONFIG_NOT_COHERENT_CACHE
From: Arnd Bergmann @ 2009-05-25 1:43 UTC (permalink / raw)
To: linuxppc-dev; +Cc: Albert Herranz, Ilya Yanok
In-Reply-To: <1243210914.24376.11.camel@pasglop>
On Monday 25 May 2009, Benjamin Herrenschmidt wrote:
> Note that I still think the right approach in the long run is to ban the
> consistent allocs from atomic contexts generically in linux, though that
> will be a hard nut to crack.
I might be missing too much context here, but can't we make drivers that
need this allocate an uncached memory range at setup time and call
dma_declare_coherent_memory() on that to make a later dma_alloc_coherent()
succeed without GFP_KERNEL?
If that is not enough, dma_alloc_coherent could be changed to
try dma_alloc_from_coherent() on the bridge device (PCI HB,
PLB4, ...), if we reserve a reasonably sized amount of uncached
memory for each bridge that has noncoherent devices.
Arnd <><
^ permalink raw reply
* can't flush tlb on e500
From: Hideo Saito @ 2009-05-25 1:33 UTC (permalink / raw)
To: linuxppc-dev; +Cc: hsaito.ppc
Hi all,
This report came from LKML, although I should post it here first,
the report said that there is a regression in linux-2.6.29 as to flushing a TLB entry that was going to be re-used when a context overflowed from the TLB.
On Fri, May 22, 2009 at 6:27 PM, Benjamin Herrenschmidt wrote:
> Have you verified that this change fixes your problem ?
I tested using "hackbench 100" and it was done successfully on my platform with e500(MPC8548).
>
> Can you re-submit to linuxppc-dev@ozlabs.org mailing list, along with
> proper changeset comment and signed-off-by: line ?
I am sorry I don't know as to the proper changeset comment.
Signed-off-by: Hideo Saito <hsaito.ppc@gmail.com>
---
--- arch/powerpc/mm/mmu_context_nohash.c.orig 2009-03-24 08:12:14.000000000 +0900
+++ arch/powerpc/mm/mmu_context_nohash.c 2009-05-20 18:33:53.000000000 +0900
@@ -122,22 +122,22 @@ static unsigned int steal_context_up(uns
struct mm_struct *mm;
int cpu = smp_processor_id();
/* Pick up the victim mm */
mm = context_mm[id];
pr_debug("[%d] steal context %d from mm @%p\n", cpu, id, mm);
- /* Mark this mm has having no context anymore */
- mm->context.id = MMU_NO_CONTEXT;
-
/* Flush the TLB for that context */
local_flush_tlb_mm(mm);
+ /* Mark this mm has having no context anymore */
+ mm->context.id = MMU_NO_CONTEXT;
+
/* XXX This clear should ultimately be part of local_flush_tlb_mm */
__clear_bit(id, stale_map[cpu]);
return id;
}
#ifdef DEBUG_MAP_CONSISTENCY
static void context_check_map(void)
^ permalink raw reply
* Re: can't flush tlb on e500
From: Benjamin Herrenschmidt @ 2009-05-25 4:20 UTC (permalink / raw)
To: Hideo Saito; +Cc: linuxppc-dev
In-Reply-To: <20090525.103334.68564567.saito@densan.co.jp>
On Mon, 2009-05-25 at 10:33 +0900, Hideo Saito wrote:
>
> This report came from LKML, although I should post it here first,
> the report said that there is a regression in linux-2.6.29 as to
> flushing a TLB entry that was going to be re-used when a context
> overflowed from the TLB.
>
> On Fri, May 22, 2009 at 6:27 PM, Benjamin Herrenschmidt wrote:
> > Have you verified that this change fixes your problem ?
>
> I tested using "hackbench 100" and it was done successfully on my
> platform with e500(MPC8548).
>
> >
> > Can you re-submit to linuxppc-dev@ozlabs.org mailing list, along
> with
> > proper changeset comment and signed-off-by: line ?
>
> I am sorry I don't know as to the proper changeset comment.
>
Well, that simply means a proper description of the bug and
the fix :-)
I'll cook up one.
Cheers,
Ben.
^ permalink raw reply
* Re: powerpc: DMA coherent allocations broken for CONFIG_NOT_COHERENT_CACHE
From: Benjamin Herrenschmidt @ 2009-05-25 4:19 UTC (permalink / raw)
To: Arnd Bergmann; +Cc: linuxppc-dev, Albert Herranz, Ilya Yanok
In-Reply-To: <200905250243.15436.arnd@arndb.de>
On Mon, 2009-05-25 at 02:43 +0100, Arnd Bergmann wrote:
> I might be missing too much context here, but can't we make drivers
> that
> need this allocate an uncached memory range at setup time and call
> dma_declare_coherent_memory() on that to make a later
> dma_alloc_coherent()
> succeed without GFP_KERNEL?
That isn't that much different, and still needs a dedicated allocator
which is pretty much what I'm trying to get rid of.
It would make everybody's life easier if we just banned those
allocations from atomic contexts :-)
Cheers,
Ben.
^ permalink raw reply
* Re: powerpc: DMA coherent allocations broken for CONFIG_NOT_COHERENT_CACHE
From: Benjamin Herrenschmidt @ 2009-05-25 4:33 UTC (permalink / raw)
To: linuxppc-dev list; +Cc: Kumar Gala, Albert Herranz, Ilya Yanok
In-Reply-To: <200905250243.15436.arnd@arndb.de>
(Please, Kumar, have a good look, especially my change to FIXMAP_TOP,
was there any reason it wasn't a constant in the first place ?)
This is going to .30 if nobody hollers. I've done some testing here
and it seems to be fine, but more eyes at this stage are much welcome.
From: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Date: Mon, 25 May 2009 14:24:43 +1000
Subject: [PATCH] Revert "powerpc: Rework dma-noncoherent to use generic vmalloc layer"
This reverts commit 33f00dcedb0e22cdb156a23632814fc580fcfcf8
... sort-of, the revived dma-noncoherent is modified from the
previous variant in a handful of ways, mostly because the
way we lay out our address space changed and I don't want
to revive a broken config option and try to find "safe"
values for all platforms (hint: there's none).
The result is a lot more invasive than I would have liked at this
stage, but I felt we had little choice here.
- We can no longer set the virtual address of the coherent mapping
(this was a big no-no) it's now fit between vmalloc/ioremap and
PKMAP (or 0xfe000000 for !CONFIG_HIGHMEM, this arbitrary limit
must die but that's work for a different patch)
- Due to the above, I had to do some small changes to various files
to make FIXADDR_TOP a compile time constant (why wasn't it so ?)
and cleaner definitions of where bits of the kernel address space
are located in pgtable_ppc32.h
- To ease debugging, we now print out the layout of the kernel
virtual address space at boot time on ppc32
- The code in dma-noncoherent.c was mostly lifted from ARM, though
the later had a few updates related to checking the DMA mask we
never brought over. This is now done.
- To avoid wasting a whole lot more address space than needed, rather
than keeping the old assumption that all PTEs for consistent memory
fit in a single PTE page and do PTE pointer manipulations, I instead
use our existing map_page() helper to create the mappings which is
also simpler. Thus, the consistent memory area has no limitations on
size and alignment now. This is a little bit slower but that shouldn't
matter as dma_alloc_coherent() shouldn't be a fast path. Similar fixes
went into the freeing path
- Finally, because it made more sense and because i wanted to include
headers local from that directory, I moved dma-noncoherent.c from
arch/powerpc/lib to arch/powerpc/mm
The reason for the revert is that while it was a good idea to try to
use the mm/vmalloc.c allocator instead of our own (in fact, ours is
itself a dup on an old variant of the vmalloc one), unfortunately,
the approach is terminally busted since dma_alloc_coherent() can be
called at interrupt time or in atomic contexts and there's little
chances we'll make the code in mm/vmalloc.c cope with that :-(
Until we can get the generic code to forbid that idiocy and fix all
drivers abusing it, we pretty much have no choice but revert to
our custom virtual space allocator.
There's also a problem with SMP safety since freeing such mapping
would require an IPI which cannot be done at interrupt time.
However, right now, I don't think we support any platform that is
both SMP and has non-coherent DMA (don't laugh, I know such things
do exist !) so we can sort that out later.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
arch/powerpc/Kconfig | 12 +
arch/powerpc/include/asm/dma-mapping.h | 6 +-
arch/powerpc/include/asm/fixmap.h | 4 +-
arch/powerpc/include/asm/pgtable-ppc32.h | 25 ++-
arch/powerpc/kernel/dma.c | 2 +-
arch/powerpc/lib/Makefile | 1 -
arch/powerpc/lib/dma-noncoherent.c | 237 ------------------
arch/powerpc/mm/Makefile | 1 +
arch/powerpc/mm/dma-noncoherent.c | 400 ++++++++++++++++++++++++++++++
arch/powerpc/mm/init_32.c | 8 +-
arch/powerpc/mm/mem.c | 19 ++
arch/powerpc/mm/pgtable_32.c | 2 -
12 files changed, 464 insertions(+), 253 deletions(-)
delete mode 100644 arch/powerpc/lib/dma-noncoherent.c
create mode 100644 arch/powerpc/mm/dma-noncoherent.c
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index a0d1146..cdc9a6f 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -868,6 +868,18 @@ config TASK_SIZE
default "0x80000000" if PPC_PREP || PPC_8xx
default "0xc0000000"
+config CONSISTENT_SIZE_BOOL
+ bool "Set custom consistent memory pool size"
+ depends on ADVANCED_OPTIONS && NOT_COHERENT_CACHE
+ help
+ This option allows you to set the size of the
+ consistent memory pool. This pool of virtual memory
+ is used to make consistent memory allocations.
+
+config CONSISTENT_SIZE
+ hex "Size of consistent memory pool" if CONSISTENT_SIZE_BOOL
+ default "0x00200000" if NOT_COHERENT_CACHE
+
config PIN_TLB
bool "Pinned Kernel TLBs (860 ONLY)"
depends on ADVANCED_OPTIONS && 8xx
diff --git a/arch/powerpc/include/asm/dma-mapping.h b/arch/powerpc/include/asm/dma-mapping.h
index c69f2b5..cb448d6 100644
--- a/arch/powerpc/include/asm/dma-mapping.h
+++ b/arch/powerpc/include/asm/dma-mapping.h
@@ -26,7 +26,9 @@
* allocate the space "normally" and use the cache management functions
* to ensure it is consistent.
*/
-extern void *__dma_alloc_coherent(size_t size, dma_addr_t *handle, gfp_t gfp);
+struct device;
+extern void *__dma_alloc_coherent(struct device *dev, size_t size,
+ dma_addr_t *handle, gfp_t gfp);
extern void __dma_free_coherent(size_t size, void *vaddr);
extern void __dma_sync(void *vaddr, size_t size, int direction);
extern void __dma_sync_page(struct page *page, unsigned long offset,
@@ -37,7 +39,7 @@ extern void __dma_sync_page(struct page *page, unsigned long offset,
* Cache coherent cores.
*/
-#define __dma_alloc_coherent(gfp, size, handle) NULL
+#define __dma_alloc_coherent(dev, gfp, size, handle) NULL
#define __dma_free_coherent(size, addr) ((void)0)
#define __dma_sync(addr, size, rw) ((void)0)
#define __dma_sync_page(pg, off, sz, rw) ((void)0)
diff --git a/arch/powerpc/include/asm/fixmap.h b/arch/powerpc/include/asm/fixmap.h
index d60fd18..f1f4e23 100644
--- a/arch/powerpc/include/asm/fixmap.h
+++ b/arch/powerpc/include/asm/fixmap.h
@@ -14,8 +14,6 @@
#ifndef _ASM_FIXMAP_H
#define _ASM_FIXMAP_H
-extern unsigned long FIXADDR_TOP;
-
#ifndef __ASSEMBLY__
#include <linux/kernel.h>
#include <asm/page.h>
@@ -24,6 +22,8 @@ extern unsigned long FIXADDR_TOP;
#include <asm/kmap_types.h>
#endif
+#define FIXADDR_TOP ((unsigned long)(-PAGE_SIZE))
+
/*
* Here we define all the compile-time 'special' virtual
* addresses. The point is to have a constant address at
diff --git a/arch/powerpc/include/asm/pgtable-ppc32.h b/arch/powerpc/include/asm/pgtable-ppc32.h
index ba45c99..4a0c08b 100644
--- a/arch/powerpc/include/asm/pgtable-ppc32.h
+++ b/arch/powerpc/include/asm/pgtable-ppc32.h
@@ -10,7 +10,7 @@
extern unsigned long va_to_phys(unsigned long address);
extern pte_t *va_to_pte(unsigned long address);
-extern unsigned long ioremap_bot, ioremap_base;
+extern unsigned long ioremap_bot;
#ifdef CONFIG_44x
extern int icache_44x_need_flush;
@@ -55,9 +55,30 @@ extern int icache_44x_need_flush;
#define pgd_ERROR(e) \
printk("%s:%d: bad pgd %08lx.\n", __FILE__, __LINE__, pgd_val(e))
+
+/*
+ * This is the bottom of the PKMAP area with HIGHMEM or an arbitrary
+ * value (for now) on others, from where we can start layout kernel
+ * virtual space that goes below PKMAP and FIXMAP
+ */
+#ifdef CONFIG_HIGHMEM
+#define KVIRT_TOP PKMAP_BASE
+#else
+#define KVIRT_TOP (0xfe000000UL) /* for now, could be FIXMAP_BASE ? */
+#endif
+
+/*
+ * This is the "top" of the ioremap space
+ */
+#ifdef CONFIG_NOT_COHERENT_CACHE
+#define IOREMAP_TOP ((KVIRT_TOP - CONFIG_CONSISTENT_SIZE) & PAGE_MASK)
+#else
+#define IOREMAP_TOP KVIRT_TOP
+#endif
+
/*
* Just any arbitrary offset to the start of the vmalloc VM area: the
- * current 64MB value just means that there will be a 64MB "hole" after the
+ * current 16MB value just means that there will be a 16MB "hole" after the
* physical memory until the kernel virtual memory starts. That means that
* any out-of-bounds memory accesses will hopefully be caught.
* The vmalloc() routines leaves a hole of 4kB between each vmalloced
diff --git a/arch/powerpc/kernel/dma.c b/arch/powerpc/kernel/dma.c
index 53c7788..6b02793 100644
--- a/arch/powerpc/kernel/dma.c
+++ b/arch/powerpc/kernel/dma.c
@@ -32,7 +32,7 @@ void *dma_direct_alloc_coherent(struct device *dev, size_t size,
{
void *ret;
#ifdef CONFIG_NOT_COHERENT_CACHE
- ret = __dma_alloc_coherent(size, dma_handle, flag);
+ ret = __dma_alloc_coherent(dev, size, dma_handle, flag);
if (ret == NULL)
return NULL;
*dma_handle += get_dma_direct_offset(dev);
diff --git a/arch/powerpc/lib/Makefile b/arch/powerpc/lib/Makefile
index 8db3527..29b742b 100644
--- a/arch/powerpc/lib/Makefile
+++ b/arch/powerpc/lib/Makefile
@@ -18,7 +18,6 @@ obj-$(CONFIG_PPC64) += copypage_64.o copyuser_64.o \
memcpy_64.o usercopy_64.o mem_64.o string.o
obj-$(CONFIG_XMON) += sstep.o
obj-$(CONFIG_KPROBES) += sstep.o
-obj-$(CONFIG_NOT_COHERENT_CACHE) += dma-noncoherent.o
ifeq ($(CONFIG_PPC64),y)
obj-$(CONFIG_SMP) += locks.o
diff --git a/arch/powerpc/lib/dma-noncoherent.c b/arch/powerpc/lib/dma-noncoherent.c
deleted file mode 100644
index 005a28d..0000000
--- a/arch/powerpc/lib/dma-noncoherent.c
+++ /dev/null
@@ -1,237 +0,0 @@
-/*
- * PowerPC version derived from arch/arm/mm/consistent.c
- * Copyright (C) 2001 Dan Malek (dmalek@jlc.net)
- *
- * Copyright (C) 2000 Russell King
- *
- * Consistent memory allocators. Used for DMA devices that want to
- * share uncached memory with the processor core. The function return
- * is the virtual address and 'dma_handle' is the physical address.
- * Mostly stolen from the ARM port, with some changes for PowerPC.
- * -- Dan
- *
- * Reorganized to get rid of the arch-specific consistent_* functions
- * and provide non-coherent implementations for the DMA API. -Matt
- *
- * Added in_interrupt() safe dma_alloc_coherent()/dma_free_coherent()
- * implementation. This is pulled straight from ARM and barely
- * modified. -Matt
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/sched.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/string.h>
-#include <linux/types.h>
-#include <linux/highmem.h>
-#include <linux/dma-mapping.h>
-#include <linux/vmalloc.h>
-
-#include <asm/tlbflush.h>
-
-/*
- * Allocate DMA-coherent memory space and return both the kernel remapped
- * virtual and bus address for that space.
- */
-void *
-__dma_alloc_coherent(size_t size, dma_addr_t *handle, gfp_t gfp)
-{
- struct page *page;
- unsigned long order;
- int i;
- unsigned int nr_pages = PAGE_ALIGN(size)>>PAGE_SHIFT;
- unsigned int array_size = nr_pages * sizeof(struct page *);
- struct page **pages;
- struct page *end;
- u64 mask = 0x00ffffff, limit; /* ISA default */
- struct vm_struct *area;
-
- BUG_ON(!mem_init_done);
- size = PAGE_ALIGN(size);
- limit = (mask + 1) & ~mask;
- if (limit && size >= limit) {
- printk(KERN_WARNING "coherent allocation too big (requested "
- "%#x mask %#Lx)\n", size, mask);
- return NULL;
- }
-
- order = get_order(size);
-
- if (mask != 0xffffffff)
- gfp |= GFP_DMA;
-
- page = alloc_pages(gfp, order);
- if (!page)
- goto no_page;
-
- end = page + (1 << order);
-
- /*
- * Invalidate any data that might be lurking in the
- * kernel direct-mapped region for device DMA.
- */
- {
- unsigned long kaddr = (unsigned long)page_address(page);
- memset(page_address(page), 0, size);
- flush_dcache_range(kaddr, kaddr + size);
- }
-
- split_page(page, order);
-
- /*
- * Set the "dma handle"
- */
- *handle = page_to_phys(page);
-
- area = get_vm_area_caller(size, VM_IOREMAP,
- __builtin_return_address(1));
- if (!area)
- goto out_free_pages;
-
- if (array_size > PAGE_SIZE) {
- pages = vmalloc(array_size);
- area->flags |= VM_VPAGES;
- } else {
- pages = kmalloc(array_size, GFP_KERNEL);
- }
- if (!pages)
- goto out_free_area;
-
- area->pages = pages;
- area->nr_pages = nr_pages;
-
- for (i = 0; i < nr_pages; i++)
- pages[i] = page + i;
-
- if (map_vm_area(area, pgprot_noncached(PAGE_KERNEL), &pages))
- goto out_unmap;
-
- /*
- * Free the otherwise unused pages.
- */
- page += nr_pages;
- while (page < end) {
- __free_page(page);
- page++;
- }
-
- return area->addr;
-out_unmap:
- vunmap(area->addr);
- if (array_size > PAGE_SIZE)
- vfree(pages);
- else
- kfree(pages);
- goto out_free_pages;
-out_free_area:
- free_vm_area(area);
-out_free_pages:
- if (page)
- __free_pages(page, order);
-no_page:
- return NULL;
-}
-EXPORT_SYMBOL(__dma_alloc_coherent);
-
-/*
- * free a page as defined by the above mapping.
- */
-void __dma_free_coherent(size_t size, void *vaddr)
-{
- vfree(vaddr);
-
-}
-EXPORT_SYMBOL(__dma_free_coherent);
-
-/*
- * make an area consistent.
- */
-void __dma_sync(void *vaddr, size_t size, int direction)
-{
- unsigned long start = (unsigned long)vaddr;
- unsigned long end = start + size;
-
- switch (direction) {
- case DMA_NONE:
- BUG();
- case DMA_FROM_DEVICE:
- /*
- * invalidate only when cache-line aligned otherwise there is
- * the potential for discarding uncommitted data from the cache
- */
- if ((start & (L1_CACHE_BYTES - 1)) || (size & (L1_CACHE_BYTES - 1)))
- flush_dcache_range(start, end);
- else
- invalidate_dcache_range(start, end);
- break;
- case DMA_TO_DEVICE: /* writeback only */
- clean_dcache_range(start, end);
- break;
- case DMA_BIDIRECTIONAL: /* writeback and invalidate */
- flush_dcache_range(start, end);
- break;
- }
-}
-EXPORT_SYMBOL(__dma_sync);
-
-#ifdef CONFIG_HIGHMEM
-/*
- * __dma_sync_page() implementation for systems using highmem.
- * In this case, each page of a buffer must be kmapped/kunmapped
- * in order to have a virtual address for __dma_sync(). This must
- * not sleep so kmap_atomic()/kunmap_atomic() are used.
- *
- * Note: yes, it is possible and correct to have a buffer extend
- * beyond the first page.
- */
-static inline void __dma_sync_page_highmem(struct page *page,
- unsigned long offset, size_t size, int direction)
-{
- size_t seg_size = min((size_t)(PAGE_SIZE - offset), size);
- size_t cur_size = seg_size;
- unsigned long flags, start, seg_offset = offset;
- int nr_segs = 1 + ((size - seg_size) + PAGE_SIZE - 1)/PAGE_SIZE;
- int seg_nr = 0;
-
- local_irq_save(flags);
-
- do {
- start = (unsigned long)kmap_atomic(page + seg_nr,
- KM_PPC_SYNC_PAGE) + seg_offset;
-
- /* Sync this buffer segment */
- __dma_sync((void *)start, seg_size, direction);
- kunmap_atomic((void *)start, KM_PPC_SYNC_PAGE);
- seg_nr++;
-
- /* Calculate next buffer segment size */
- seg_size = min((size_t)PAGE_SIZE, size - cur_size);
-
- /* Add the segment size to our running total */
- cur_size += seg_size;
- seg_offset = 0;
- } while (seg_nr < nr_segs);
-
- local_irq_restore(flags);
-}
-#endif /* CONFIG_HIGHMEM */
-
-/*
- * __dma_sync_page makes memory consistent. identical to __dma_sync, but
- * takes a struct page instead of a virtual address
- */
-void __dma_sync_page(struct page *page, unsigned long offset,
- size_t size, int direction)
-{
-#ifdef CONFIG_HIGHMEM
- __dma_sync_page_highmem(page, offset, size, direction);
-#else
- unsigned long start = (unsigned long)page_address(page) + offset;
- __dma_sync((void *)start, size, direction);
-#endif
-}
-EXPORT_SYMBOL(__dma_sync_page);
diff --git a/arch/powerpc/mm/Makefile b/arch/powerpc/mm/Makefile
index 17290bc..fc5c4c2 100644
--- a/arch/powerpc/mm/Makefile
+++ b/arch/powerpc/mm/Makefile
@@ -26,3 +26,4 @@ obj-$(CONFIG_NEED_MULTIPLE_NODES) += numa.o
obj-$(CONFIG_PPC_MM_SLICES) += slice.o
obj-$(CONFIG_HUGETLB_PAGE) += hugetlbpage.o
obj-$(CONFIG_PPC_SUBPAGE_PROT) += subpage-prot.o
+obj-$(CONFIG_NOT_COHERENT_CACHE) += dma-noncoherent.o
diff --git a/arch/powerpc/mm/dma-noncoherent.c b/arch/powerpc/mm/dma-noncoherent.c
new file mode 100644
index 0000000..36692f5
--- /dev/null
+++ b/arch/powerpc/mm/dma-noncoherent.c
@@ -0,0 +1,400 @@
+/*
+ * PowerPC version derived from arch/arm/mm/consistent.c
+ * Copyright (C) 2001 Dan Malek (dmalek@jlc.net)
+ *
+ * Copyright (C) 2000 Russell King
+ *
+ * Consistent memory allocators. Used for DMA devices that want to
+ * share uncached memory with the processor core. The function return
+ * is the virtual address and 'dma_handle' is the physical address.
+ * Mostly stolen from the ARM port, with some changes for PowerPC.
+ * -- Dan
+ *
+ * Reorganized to get rid of the arch-specific consistent_* functions
+ * and provide non-coherent implementations for the DMA API. -Matt
+ *
+ * Added in_interrupt() safe dma_alloc_coherent()/dma_free_coherent()
+ * implementation. This is pulled straight from ARM and barely
+ * modified. -Matt
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/sched.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/string.h>
+#include <linux/types.h>
+#include <linux/highmem.h>
+#include <linux/dma-mapping.h>
+
+#include <asm/tlbflush.h>
+
+#include "mmu_decl.h"
+
+/*
+ * This address range defaults to a value that is safe for all
+ * platforms which currently set CONFIG_NOT_COHERENT_CACHE. It
+ * can be further configured for specific applications under
+ * the "Advanced Setup" menu. -Matt
+ */
+#define CONSISTENT_BASE (IOREMAP_TOP)
+#define CONSISTENT_END (CONSISTENT_BASE + CONFIG_CONSISTENT_SIZE)
+#define CONSISTENT_OFFSET(x) (((unsigned long)(x) - CONSISTENT_BASE) >> PAGE_SHIFT)
+
+/*
+ * This is the page table (2MB) covering uncached, DMA consistent allocations
+ */
+static DEFINE_SPINLOCK(consistent_lock);
+
+/*
+ * VM region handling support.
+ *
+ * This should become something generic, handling VM region allocations for
+ * vmalloc and similar (ioremap, module space, etc).
+ *
+ * I envisage vmalloc()'s supporting vm_struct becoming:
+ *
+ * struct vm_struct {
+ * struct vm_region region;
+ * unsigned long flags;
+ * struct page **pages;
+ * unsigned int nr_pages;
+ * unsigned long phys_addr;
+ * };
+ *
+ * get_vm_area() would then call vm_region_alloc with an appropriate
+ * struct vm_region head (eg):
+ *
+ * struct vm_region vmalloc_head = {
+ * .vm_list = LIST_HEAD_INIT(vmalloc_head.vm_list),
+ * .vm_start = VMALLOC_START,
+ * .vm_end = VMALLOC_END,
+ * };
+ *
+ * However, vmalloc_head.vm_start is variable (typically, it is dependent on
+ * the amount of RAM found at boot time.) I would imagine that get_vm_area()
+ * would have to initialise this each time prior to calling vm_region_alloc().
+ */
+struct ppc_vm_region {
+ struct list_head vm_list;
+ unsigned long vm_start;
+ unsigned long vm_end;
+};
+
+static struct ppc_vm_region consistent_head = {
+ .vm_list = LIST_HEAD_INIT(consistent_head.vm_list),
+ .vm_start = CONSISTENT_BASE,
+ .vm_end = CONSISTENT_END,
+};
+
+static struct ppc_vm_region *
+ppc_vm_region_alloc(struct ppc_vm_region *head, size_t size, gfp_t gfp)
+{
+ unsigned long addr = head->vm_start, end = head->vm_end - size;
+ unsigned long flags;
+ struct ppc_vm_region *c, *new;
+
+ new = kmalloc(sizeof(struct ppc_vm_region), gfp);
+ if (!new)
+ goto out;
+
+ spin_lock_irqsave(&consistent_lock, flags);
+
+ list_for_each_entry(c, &head->vm_list, vm_list) {
+ if ((addr + size) < addr)
+ goto nospc;
+ if ((addr + size) <= c->vm_start)
+ goto found;
+ addr = c->vm_end;
+ if (addr > end)
+ goto nospc;
+ }
+
+ found:
+ /*
+ * Insert this entry _before_ the one we found.
+ */
+ list_add_tail(&new->vm_list, &c->vm_list);
+ new->vm_start = addr;
+ new->vm_end = addr + size;
+
+ spin_unlock_irqrestore(&consistent_lock, flags);
+ return new;
+
+ nospc:
+ spin_unlock_irqrestore(&consistent_lock, flags);
+ kfree(new);
+ out:
+ return NULL;
+}
+
+static struct ppc_vm_region *ppc_vm_region_find(struct ppc_vm_region *head, unsigned long addr)
+{
+ struct ppc_vm_region *c;
+
+ list_for_each_entry(c, &head->vm_list, vm_list) {
+ if (c->vm_start == addr)
+ goto out;
+ }
+ c = NULL;
+ out:
+ return c;
+}
+
+/*
+ * Allocate DMA-coherent memory space and return both the kernel remapped
+ * virtual and bus address for that space.
+ */
+void *
+__dma_alloc_coherent(struct device *dev, size_t size, dma_addr_t *handle, gfp_t gfp)
+{
+ struct page *page;
+ struct ppc_vm_region *c;
+ unsigned long order;
+ u64 mask = ISA_DMA_THRESHOLD, limit;
+
+ if (dev) {
+ mask = dev->coherent_dma_mask;
+
+ /*
+ * Sanity check the DMA mask - it must be non-zero, and
+ * must be able to be satisfied by a DMA allocation.
+ */
+ if (mask == 0) {
+ dev_warn(dev, "coherent DMA mask is unset\n");
+ goto no_page;
+ }
+
+ if ((~mask) & ISA_DMA_THRESHOLD) {
+ dev_warn(dev, "coherent DMA mask %#llx is smaller "
+ "than system GFP_DMA mask %#llx\n",
+ mask, (unsigned long long)ISA_DMA_THRESHOLD);
+ goto no_page;
+ }
+ }
+
+
+ size = PAGE_ALIGN(size);
+ limit = (mask + 1) & ~mask;
+ if ((limit && size >= limit) ||
+ size >= (CONSISTENT_END - CONSISTENT_BASE)) {
+ printk(KERN_WARNING "coherent allocation too big (requested %#x mask %#Lx)\n",
+ size, mask);
+ return NULL;
+ }
+
+ order = get_order(size);
+
+ /* Might be useful if we ever have a real legacy DMA zone... */
+ if (mask != 0xffffffff)
+ gfp |= GFP_DMA;
+
+ page = alloc_pages(gfp, order);
+ if (!page)
+ goto no_page;
+
+ /*
+ * Invalidate any data that might be lurking in the
+ * kernel direct-mapped region for device DMA.
+ */
+ {
+ unsigned long kaddr = (unsigned long)page_address(page);
+ memset(page_address(page), 0, size);
+ flush_dcache_range(kaddr, kaddr + size);
+ }
+
+ /*
+ * Allocate a virtual address in the consistent mapping region.
+ */
+ c = ppc_vm_region_alloc(&consistent_head, size,
+ gfp & ~(__GFP_DMA | __GFP_HIGHMEM));
+ if (c) {
+ unsigned long vaddr = c->vm_start;
+ struct page *end = page + (1 << order);
+
+ split_page(page, order);
+
+ /*
+ * Set the "dma handle"
+ */
+ *handle = page_to_phys(page);
+
+ do {
+ SetPageReserved(page);
+ map_page(vaddr, page_to_phys(page),
+ pgprot_noncached(PAGE_KERNEL));
+ page++;
+ vaddr += PAGE_SIZE;
+ } while (size -= PAGE_SIZE);
+
+ /*
+ * Free the otherwise unused pages.
+ */
+ while (page < end) {
+ __free_page(page);
+ page++;
+ }
+
+ return (void *)c->vm_start;
+ }
+
+ if (page)
+ __free_pages(page, order);
+ no_page:
+ return NULL;
+}
+EXPORT_SYMBOL(__dma_alloc_coherent);
+
+/*
+ * free a page as defined by the above mapping.
+ */
+void __dma_free_coherent(size_t size, void *vaddr)
+{
+ struct ppc_vm_region *c;
+ unsigned long flags, addr;
+
+ size = PAGE_ALIGN(size);
+
+ spin_lock_irqsave(&consistent_lock, flags);
+
+ c = ppc_vm_region_find(&consistent_head, (unsigned long)vaddr);
+ if (!c)
+ goto no_area;
+
+ if ((c->vm_end - c->vm_start) != size) {
+ printk(KERN_ERR "%s: freeing wrong coherent size (%ld != %d)\n",
+ __func__, c->vm_end - c->vm_start, size);
+ dump_stack();
+ size = c->vm_end - c->vm_start;
+ }
+
+ addr = c->vm_start;
+ do {
+ pte_t *ptep;
+ unsigned long pfn;
+
+ ptep = pte_offset_kernel(pmd_offset(pud_offset(pgd_offset_k(addr),
+ addr),
+ addr),
+ addr);
+ if (!pte_none(*ptep) && pte_present(*ptep)) {
+ pfn = pte_pfn(*ptep);
+ pte_clear(&init_mm, addr, ptep);
+ if (pfn_valid(pfn)) {
+ struct page *page = pfn_to_page(pfn);
+
+ ClearPageReserved(page);
+ __free_page(page);
+ }
+ }
+ addr += PAGE_SIZE;
+ } while (size -= PAGE_SIZE);
+
+ flush_tlb_kernel_range(c->vm_start, c->vm_end);
+
+ list_del(&c->vm_list);
+
+ spin_unlock_irqrestore(&consistent_lock, flags);
+
+ kfree(c);
+ return;
+
+ no_area:
+ spin_unlock_irqrestore(&consistent_lock, flags);
+ printk(KERN_ERR "%s: trying to free invalid coherent area: %p\n",
+ __func__, vaddr);
+ dump_stack();
+}
+EXPORT_SYMBOL(__dma_free_coherent);
+
+/*
+ * make an area consistent.
+ */
+void __dma_sync(void *vaddr, size_t size, int direction)
+{
+ unsigned long start = (unsigned long)vaddr;
+ unsigned long end = start + size;
+
+ switch (direction) {
+ case DMA_NONE:
+ BUG();
+ case DMA_FROM_DEVICE:
+ /*
+ * invalidate only when cache-line aligned otherwise there is
+ * the potential for discarding uncommitted data from the cache
+ */
+ if ((start & (L1_CACHE_BYTES - 1)) || (size & (L1_CACHE_BYTES - 1)))
+ flush_dcache_range(start, end);
+ else
+ invalidate_dcache_range(start, end);
+ break;
+ case DMA_TO_DEVICE: /* writeback only */
+ clean_dcache_range(start, end);
+ break;
+ case DMA_BIDIRECTIONAL: /* writeback and invalidate */
+ flush_dcache_range(start, end);
+ break;
+ }
+}
+EXPORT_SYMBOL(__dma_sync);
+
+#ifdef CONFIG_HIGHMEM
+/*
+ * __dma_sync_page() implementation for systems using highmem.
+ * In this case, each page of a buffer must be kmapped/kunmapped
+ * in order to have a virtual address for __dma_sync(). This must
+ * not sleep so kmap_atomic()/kunmap_atomic() are used.
+ *
+ * Note: yes, it is possible and correct to have a buffer extend
+ * beyond the first page.
+ */
+static inline void __dma_sync_page_highmem(struct page *page,
+ unsigned long offset, size_t size, int direction)
+{
+ size_t seg_size = min((size_t)(PAGE_SIZE - offset), size);
+ size_t cur_size = seg_size;
+ unsigned long flags, start, seg_offset = offset;
+ int nr_segs = 1 + ((size - seg_size) + PAGE_SIZE - 1)/PAGE_SIZE;
+ int seg_nr = 0;
+
+ local_irq_save(flags);
+
+ do {
+ start = (unsigned long)kmap_atomic(page + seg_nr,
+ KM_PPC_SYNC_PAGE) + seg_offset;
+
+ /* Sync this buffer segment */
+ __dma_sync((void *)start, seg_size, direction);
+ kunmap_atomic((void *)start, KM_PPC_SYNC_PAGE);
+ seg_nr++;
+
+ /* Calculate next buffer segment size */
+ seg_size = min((size_t)PAGE_SIZE, size - cur_size);
+
+ /* Add the segment size to our running total */
+ cur_size += seg_size;
+ seg_offset = 0;
+ } while (seg_nr < nr_segs);
+
+ local_irq_restore(flags);
+}
+#endif /* CONFIG_HIGHMEM */
+
+/*
+ * __dma_sync_page makes memory consistent. identical to __dma_sync, but
+ * takes a struct page instead of a virtual address
+ */
+void __dma_sync_page(struct page *page, unsigned long offset,
+ size_t size, int direction)
+{
+#ifdef CONFIG_HIGHMEM
+ __dma_sync_page_highmem(page, offset, size, direction);
+#else
+ unsigned long start = (unsigned long)page_address(page) + offset;
+ __dma_sync((void *)start, size, direction);
+#endif
+}
+EXPORT_SYMBOL(__dma_sync_page);
diff --git a/arch/powerpc/mm/init_32.c b/arch/powerpc/mm/init_32.c
index 666a5e8..3de6a0d 100644
--- a/arch/powerpc/mm/init_32.c
+++ b/arch/powerpc/mm/init_32.c
@@ -168,12 +168,8 @@ void __init MMU_init(void)
ppc_md.progress("MMU:mapin", 0x301);
mapin_ram();
-#ifdef CONFIG_HIGHMEM
- ioremap_base = PKMAP_BASE;
-#else
- ioremap_base = 0xfe000000UL; /* for now, could be 0xfffff000 */
-#endif /* CONFIG_HIGHMEM */
- ioremap_bot = ioremap_base;
+ /* Initialize early top-down ioremap allocator */
+ ioremap_bot = IOREMAP_TOP;
/* Map in I/O resources */
if (ppc_md.progress)
diff --git a/arch/powerpc/mm/mem.c b/arch/powerpc/mm/mem.c
index d0602a7..1435c4b 100644
--- a/arch/powerpc/mm/mem.c
+++ b/arch/powerpc/mm/mem.c
@@ -296,6 +296,7 @@ void __init paging_init(void)
(unsigned long long)top_of_ram, total_ram);
printk(KERN_DEBUG "Memory hole size: %ldMB\n",
(long int)((top_of_ram - total_ram) >> 20));
+
memset(max_zone_pfns, 0, sizeof(max_zone_pfns));
#ifdef CONFIG_HIGHMEM
max_zone_pfns[ZONE_DMA] = lowmem_end_addr >> PAGE_SHIFT;
@@ -380,6 +381,24 @@ void __init mem_init(void)
bsssize >> 10,
initsize >> 10);
+#ifdef CONFIG_PPC32
+ printk(KERN_INFO "Kernel virtual memory layout:\n");
+ printk(KERN_INFO " * 0x%08lx..0x%08lx : fixmap\n",
+ FIXADDR_START, FIXADDR_TOP);
+#ifdef CONFIG_HIGHMEM
+ printk(KERN_INFO " * 0x%08lx..0x%08lx : highmem PTEs\n",
+ PKMAP_BASE, PKMAP_ADDR(LAST_PKMAP));
+#endif /* CONFIG_HIGHMEM */
+#ifdef CONFIG_NOT_COHERENT_CACHE
+ printk(KERN_INFO " * 0x%08lx..0x%08lx : consistent mem\n",
+ IOREMAP_TOP, IOREMAP_TOP + CONFIG_CONSISTENT_SIZE);
+#endif /* CONFIG_NOT_COHERENT_CACHE */
+ printk(KERN_INFO " * 0x%08lx..0x%08lx : early ioremap\n",
+ ioremap_bot, IOREMAP_TOP);
+ printk(KERN_INFO " * 0x%08lx..0x%08lx : vmalloc & ioremap\n",
+ VMALLOC_START, VMALLOC_END);
+#endif /* CONFIG_PPC32 */
+
mem_init_done = 1;
}
diff --git a/arch/powerpc/mm/pgtable_32.c b/arch/powerpc/mm/pgtable_32.c
index 430d090..5422169 100644
--- a/arch/powerpc/mm/pgtable_32.c
+++ b/arch/powerpc/mm/pgtable_32.c
@@ -399,8 +399,6 @@ void kernel_map_pages(struct page *page, int numpages, int enable)
#endif /* CONFIG_DEBUG_PAGEALLOC */
static int fixmaps;
-unsigned long FIXADDR_TOP = (-PAGE_SIZE);
-EXPORT_SYMBOL(FIXADDR_TOP);
void __set_fixmap (enum fixed_addresses idx, phys_addr_t phys, pgprot_t flags)
{
--
1.6.1.2.14.gf26b5
^ permalink raw reply related
* Wrong looking statement in cpm_common.c
From: Benjamin Herrenschmidt @ 2009-05-25 4:00 UTC (permalink / raw)
To: Scott Wood; +Cc: linuxppc-dev list
Hi Scott !
There's this pearl in cpm_common.c :
void __init udbg_init_cpm(void)
{
if (cpm_udbg_txdesc) {
#ifdef CONFIG_CPM2
setbat(1, 0xf0000000, 0xf0000000, 1024*1024, PAGE_KERNEL_NCG);
#endif
udbg_putc = udbg_putc_cpm;
}
}
Now, last I looked, 0xf0000000 (virtual) lands about right in the middle
of the vmalloc space... so unless there's code somewhere that I missed
that reserves that region of virtual space for use by that crap above,
I think somebody is in trouble :-)
Additionally, that's the last user of setbat that I can find outside
of the linear mapping setup proper, so scott, once you've fixed that
I'll happily make setbat static once for all. We -can- still provide
a facility for using BATs for early ioremap's but that should be done
properly, not by whacking setbat with random hard wired virtual
addresses.
Cheers,
Ben.
^ permalink raw reply
* Re: powerpc: DMA coherent allocations broken for CONFIG_NOT_COHERENT_CACHE
From: Grant Likely @ 2009-05-25 5:50 UTC (permalink / raw)
To: Benjamin Herrenschmidt
Cc: linuxppc-dev list, Albert Herranz, Ilya Yanok, Kumar Gala
In-Reply-To: <1243226023.24376.23.camel@pasglop>
On Sun, May 24, 2009 at 10:33 PM, Benjamin Herrenschmidt
<benh@kernel.crashing.org> wrote:
> This is going to .30 if nobody hollers. I've done some testing here
> and it seems to be fine, but more eyes at this stage are much welcome.
Looks okay to me; but I'm not an expert in this area. Boots fine on
Xilinx Virtex 440 and MPC5200. One minor nit below.
Acked-by: Grant Likely <grant.likely@secretlab.ca>
> +#ifdef CONFIG_PPC32
> + =A0 =A0 =A0 printk(KERN_INFO "Kernel virtual memory layout:\n");
> + =A0 =A0 =A0 printk(KERN_INFO " =A0* 0x%08lx..0x%08lx =A0: fixmap\n",
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0FIXADDR_START, FIXADDR_TOP);
> +#ifdef CONFIG_HIGHMEM
> + =A0 =A0 =A0 printk(KERN_INFO " =A0* 0x%08lx..0x%08lx =A0: highmem PTEs\=
n",
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0PKMAP_BASE, PKMAP_ADDR(LAST_PKMAP));
> +#endif /* CONFIG_HIGHMEM */
> +#ifdef CONFIG_NOT_COHERENT_CACHE
> + =A0 =A0 =A0 printk(KERN_INFO " =A0* 0x%08lx..0x%08lx =A0: consistent me=
m\n",
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0IOREMAP_TOP, IOREMAP_TOP + CONFIG_CONSISTENT=
_SIZE);
> +#endif /* CONFIG_NOT_COHERENT_CACHE */
> + =A0 =A0 =A0 printk(KERN_INFO " =A0* 0x%08lx..0x%08lx =A0: early ioremap=
\n",
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0ioremap_bot, IOREMAP_TOP);
> + =A0 =A0 =A0 printk(KERN_INFO " =A0* 0x%08lx..0x%08lx =A0: vmalloc & ior=
emap\n",
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0VMALLOC_START, VMALLOC_END);
> +#endif /* CONFIG_PPC32 */
NIT: pr_info(). Same goes for other printk's in this patch.
It would also be nice for comprehension if the file move and the
modification were separate commits. As it is I had to generate the
diff manually, but I'm not concerned.
g.
--=20
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
^ permalink raw reply
* Re: AMCC 405ex memory size issue
From: konamo @ 2009-05-25 6:15 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <23631525.post@talk.nabble.com>
any ideas?
konamo wrote:
>
> Hi all,
> we are using AMCC 405ex kilauea eval board as a demo, not use any
> pci/nand function,
> the board configuration is below:
> u-boot 2009.01,
> linux-2.6.25-rc2,
> 1GB DDR2 memory(2Gbit * 4, 1 rank),
> AMCC powerpc 405ex,
> both 1G and 512MB memory works fine under u-boot, but linux boot fails in
> 1G memory, if we limit mem=512M, linux could boot over nfs. Could anyone
> pls help us how to find the root cause? thanks
>
--
View this message in context: http://www.nabble.com/AMCC-405ex-memory-size-issue-tp23631525p23701685.html
Sent from the linuxppc-dev mailing list archive at Nabble.com.
^ permalink raw reply
* Re: [PATCH V3 2/4] AC97 driver for mpc5200
From: Grant Likely @ 2009-05-25 6:16 UTC (permalink / raw)
To: Jon Smirl; +Cc: linuxppc-dev, alsa-devel, broonie
In-Reply-To: <20090525013849.3073.96729.stgit@terra>
On Sun, May 24, 2009 at 7:38 PM, Jon Smirl <jonsmirl@gmail.com> wrote:
> AC97 driver for mpc5200
>
> I've implemented retries for when the AC97 hardware doesn't reset on
> first try. About 10% of the time both the Efika and pcm030 AC97 codecs
> don't reset on first try and need to be poked multiple times. =A0Failure
> is indicated by not having the link clock start ticking. Every once in
> a while even five pokes won't get the link started and I have to power
> cycle.
>
> Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
> ---
> =A0sound/soc/fsl/Kconfig =A0 =A0 =A0 =A0 =A0 =A0| =A0 11 +
> =A0sound/soc/fsl/Makefile =A0 =A0 =A0 =A0 =A0 | =A0 =A01
> =A0sound/soc/fsl/mpc5200_psc_ac97.c | =A0392 ++++++++++++++++++++++++++++=
++++++++++
> =A0sound/soc/fsl/mpc5200_psc_ac97.h | =A0 15 +
> =A04 files changed, 419 insertions(+), 0 deletions(-)
> =A0create mode 100644 sound/soc/fsl/mpc5200_psc_ac97.c
> =A0create mode 100644 sound/soc/fsl/mpc5200_psc_ac97.h
>
> diff --git a/sound/soc/fsl/Kconfig b/sound/soc/fsl/Kconfig
> index 1918c78..3bce952 100644
> --- a/sound/soc/fsl/Kconfig
> +++ b/sound/soc/fsl/Kconfig
> @@ -29,3 +29,14 @@ config SND_SOC_MPC5200_I2S
> =A0 =A0 =A0 =A0select PPC_BESTCOMM_GEN_BD
> =A0 =A0 =A0 =A0help
> =A0 =A0 =A0 =A0 =A0Say Y here to support the MPC5200 PSCs in I2S mode.
> +
> +config SND_SOC_MPC5200_AC97
> + =A0 =A0 =A0 tristate "Freescale MPC5200 PSC in AC97 mode driver"
> + =A0 =A0 =A0 depends on PPC_MPC52xx && PPC_BESTCOMM
> + =A0 =A0 =A0 select AC97_BUS
> + =A0 =A0 =A0 select SND_MPC52xx_DMA
> + =A0 =A0 =A0 select PPC_BESTCOMM_GEN_BD
> + =A0 =A0 =A0 help
> + =A0 =A0 =A0 =A0 Say Y here to support the MPC5200 PSCs in AC97 mode.
> +
> +
> diff --git a/sound/soc/fsl/Makefile b/sound/soc/fsl/Makefile
> index 7731ef2..14631a1 100644
> --- a/sound/soc/fsl/Makefile
> +++ b/sound/soc/fsl/Makefile
> @@ -13,4 +13,5 @@ obj-$(CONFIG_SND_SOC_MPC8610) +=3D snd-soc-fsl-ssi.o sn=
d-soc-fsl-dma.o
> =A0# MPC5200 Platform Support
> =A0obj-$(CONFIG_SND_MPC52xx_DMA) +=3D mpc5200_dma.o
> =A0obj-$(CONFIG_SND_SOC_MPC5200_I2S) +=3D mpc5200_psc_i2s.o
> +obj-$(CONFIG_SND_SOC_MPC5200_AC97) +=3D mpc5200_psc_ac97.o
>
> diff --git a/sound/soc/fsl/mpc5200_psc_ac97.c b/sound/soc/fsl/mpc5200_psc=
_ac97.c
> new file mode 100644
> index 0000000..480b677
> --- /dev/null
> +++ b/sound/soc/fsl/mpc5200_psc_ac97.c
> @@ -0,0 +1,392 @@
> +/*
> + * linux/sound/mpc5200-ac97.c -- AC97 support for the Freescale MPC52xx =
chip.
> + *
> + * Copyright (C) 2009 Jon Smirl, Digispeaker
> + * Author: Jon Smirl <jonsmirl@gmail.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/of_platform.h>
> +
> +#include <sound/pcm.h>
> +#include <sound/pcm_params.h>
> +#include <sound/soc.h>
> +
> +#include <asm/mpc52xx_psc.h>
> +
> +#include "mpc5200_dma.h"
> +#include "mpc5200_psc_ac97.h"
> +
> +#define DRV_NAME "mpc5200-psc-ac97"
> +
> +/* ALSA only supports a single AC97 device so static is recommend here *=
/
> +static struct psc_dma *psc_dma;
> +
> +static unsigned short psc_ac97_read(struct snd_ac97 *ac97, unsigned shor=
t reg)
> +{
> + =A0 =A0 =A0 int timeout;
> + =A0 =A0 =A0 unsigned int val;
> +
> + =A0 =A0 =A0 spin_lock(&psc_dma->lock);
> +
> + =A0 =A0 =A0 /* Wait for it to be ready */
> + =A0 =A0 =A0 timeout =3D 1000;
> + =A0 =A0 =A0 while ((--timeout) && (in_be16(&psc_dma->psc_regs->sr_csr.s=
tatus) &
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0=
=A0 =A0 =A0 =A0 =A0 MPC52xx_PSC_SR_CMDSEND))
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 udelay(10);
Holy unbounded latency Batman! This code waits up to 10ms for a register r=
ead!
I hate spinning, but if it must be done; I'd like to see it small.
What is the worst case latency? 125us for 8000Hz bus speed? If you
must spin; can a cpu_relax() be used instead of the udelay() while
watch the timebase? Timur recently posted a patch which makes this
easier.
http://patchwork.ozlabs.org/patch/27414/
They *should* be appearing in Ben's -next branch soon.
> +
> + =A0 =A0 =A0 if (!timeout) {
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 pr_err("timeout on ac97 bus (rdy)\n");
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 return 0xffff;
> + =A0 =A0 =A0 }
> +
> + =A0 =A0 =A0 /* Do the read */
> + =A0 =A0 =A0 out_be32(&psc_dma->psc_regs->ac97_cmd, (1<<31) | ((reg & 0x=
7f) << 24));
> +
> + =A0 =A0 =A0 /* Wait for the answer */
> + =A0 =A0 =A0 timeout =3D 1000;
> + =A0 =A0 =A0 while ((--timeout) && !(in_be16(&psc_dma->psc_regs->sr_csr.=
status) &
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0=
=A0 =A0 =A0 =A0 =A0 MPC52xx_PSC_SR_DATA_VAL))
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 udelay(10);
ditto.
> +static int psc_ac97_cold_reset_check(struct snd_ac97 *ac97)
> +{
> + =A0 =A0 =A0 int max_reset, timeout;
> + =A0 =A0 =A0 struct mpc52xx_psc __iomem *regs =3D psc_dma->psc_regs;
> +
> + =A0 =A0 =A0 /* AC97 clock is generated by the codec.
> + =A0 =A0 =A0 =A0* Ensure that it starts ticking after codec reset.
> + =A0 =A0 =A0 =A0*/
> + =A0 =A0 =A0 for (max_reset =3D 0; max_reset < 5; max_reset++) {
> +
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 /* Do a cold reset */
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_8(®s->op1, MPC52xx_PSC_OP_RES);
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 udelay(10);
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_8(®s->op0, MPC52xx_PSC_OP_RES);
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 udelay(50);
:-/ Don't like, but don't know if there is an alternative.
> +
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 /* PSC recover from cold reset
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0* (cfr user manual, not sure if useful)
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0*/
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_be32(®s->sicr, in_be32(®s->sicr))=
;
> +
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 psc_ac97_warm_reset(ac97);
> +
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 /* first make sure AC97 clock is low */
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 for (timeout =3D 0; ((in_8(®s->ipcr_acr.=
ipcr) & 0x80) !=3D 0) &&
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 (timeout < =
100); timeout++)
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 udelay(10);
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 if (timeout =3D=3D 100)
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 continue;
> +
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 /* then wait for the transition to high */
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 for (timeout =3D 0; ((in_8(®s->ipcr_acr.=
ipcr) & 0x80) =3D=3D 0) &&
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 (timeout < =
100); timeout++)
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 udelay(10);
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 if (timeout =3D=3D 100)
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 continue;
Using udelay makes this less accurate. Only possible reason to use a
udelay is if the register cannot be polled at full speed (which is
possibly the case if it adds bus contention; but I don't think it is
an issue here).
g.
--=20
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
^ permalink raw reply
* Re: [PATCH V3 1/4] Main rewite of the mpc5200 audio DMA code
From: Grant Likely @ 2009-05-25 6:26 UTC (permalink / raw)
To: Jon Smirl; +Cc: linuxppc-dev, alsa-devel, broonie
In-Reply-To: <20090525013847.3073.55951.stgit@terra>
On Sun, May 24, 2009 at 7:38 PM, Jon Smirl <jonsmirl@gmail.com> wrote:
> Rewrite the mpc5200 audio DMA code to support both I2S and AC97.
>
> Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
> ---
> =A0sound/soc/fsl/Kconfig =A0 =A0 =A0 =A0 =A0 | =A0 =A01
> =A0sound/soc/fsl/mpc5200_dma.c =A0 =A0 | =A0504 +++++++++++++++++++++++++=
+-------------
> =A0sound/soc/fsl/mpc5200_dma.h =A0 =A0 | =A0 33 +--
> =A0sound/soc/fsl/mpc5200_psc_i2s.c | =A0247 +++----------------
> =A0sound/soc/fsl/mpc5200_psc_i2s.h | =A0 12 +
> =A05 files changed, 408 insertions(+), 389 deletions(-)
> =A0create mode 100644 sound/soc/fsl/mpc5200_psc_i2s.h
>
> diff --git a/sound/soc/fsl/Kconfig b/sound/soc/fsl/Kconfig
> index dc79bdf..1918c78 100644
> --- a/sound/soc/fsl/Kconfig
> +++ b/sound/soc/fsl/Kconfig
> @@ -25,7 +25,6 @@ config SND_SOC_MPC8610_HPCD
> =A0config SND_SOC_MPC5200_I2S
> =A0 =A0 =A0 =A0tristate "Freescale MPC5200 PSC in I2S mode driver"
> =A0 =A0 =A0 =A0depends on PPC_MPC52xx && PPC_BESTCOMM
> - =A0 =A0 =A0 select SND_SOC_OF_SIMPLE
> =A0 =A0 =A0 =A0select SND_MPC52xx_DMA
> =A0 =A0 =A0 =A0select PPC_BESTCOMM_GEN_BD
> =A0 =A0 =A0 =A0help
> diff --git a/sound/soc/fsl/mpc5200_dma.c b/sound/soc/fsl/mpc5200_dma.c
> index 6850392..4e1f1f8 100644
> --- a/sound/soc/fsl/mpc5200_dma.c
> +++ b/sound/soc/fsl/mpc5200_dma.c
> @@ -3,23 +3,13 @@
> =A0* ALSA SoC Platform driver
> =A0*
> =A0* Copyright (C) 2008 Secret Lab Technologies Ltd.
> + * Copyright (C) 2009 Jon Smirl, Digispeaker
> =A0*/
>
> -#include <linux/init.h>
> =A0#include <linux/module.h>
> -#include <linux/interrupt.h>
> -#include <linux/device.h>
> -#include <linux/delay.h>
> =A0#include <linux/of_device.h>
> -#include <linux/of_platform.h>
> -#include <linux/dma-mapping.h>
>
> -#include <sound/core.h>
> -#include <sound/pcm.h>
> -#include <sound/pcm_params.h>
> -#include <sound/initval.h>
> =A0#include <sound/soc.h>
> -#include <sound/soc-of-simple.h>
>
> =A0#include <sysdev/bestcomm/bestcomm.h>
> =A0#include <sysdev/bestcomm/gen_bd.h>
> @@ -27,10 +17,6 @@
>
> =A0#include "mpc5200_dma.h"
>
> -MODULE_AUTHOR("Grant Likely <grant.likely@secretlab.ca>");
> -MODULE_DESCRIPTION("Freescale MPC5200 PSC in DMA mode ASoC Driver");
> -MODULE_LICENSE("GPL");
> -
> =A0/*
> =A0* Interrupt handlers
> =A0*/
> @@ -50,7 +36,7 @@ static irqreturn_t psc_dma_status_irq(int irq, void *_p=
sc_dma)
> =A0 =A0 =A0 =A0if (psc_dma->capture.active && (isr & MPC52xx_PSC_IMR_ORER=
R))
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0psc_dma->stats.overrun_count++;
>
> - =A0 =A0 =A0 out_8(®s->command, 4 << 4); =A0/* reset the error status=
*/
> + =A0 =A0 =A0 out_8(®s->command, MPC52xx_PSC_RST_ERR_STAT);
>
> =A0 =A0 =A0 =A0return IRQ_HANDLED;
> =A0}
> @@ -81,8 +67,21 @@ static void psc_dma_bcom_enqueue_next_buffer(struct ps=
c_dma_stream *s)
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0s->period_next_pt =3D s->period_start;
> =A0}
>
> +static void psc_dma_bcom_enqueue_tx(struct psc_dma_stream *s)
> +{
> + =A0 =A0 =A0 while (s->appl_ptr < s->runtime->control->appl_ptr) {
> +
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 if (bcom_queue_full(s->bcom_task))
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 return;
> +
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 s->appl_ptr +=3D s->period_size;
> +
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 psc_dma_bcom_enqueue_next_buffer(s);
> + =A0 =A0 =A0 }
> +}
> +
> =A0/* Bestcomm DMA irq handler */
> -static irqreturn_t psc_dma_bcom_irq(int irq, void *_psc_dma_stream)
> +static irqreturn_t psc_dma_bcom_irq_tx(int irq, void *_psc_dma_stream)
> =A0{
> =A0 =A0 =A0 =A0struct psc_dma_stream *s =3D _psc_dma_stream;
>
> @@ -90,12 +89,12 @@ static irqreturn_t psc_dma_bcom_irq(int irq, void *_p=
sc_dma_stream)
> =A0 =A0 =A0 =A0 * and enqueue a new one in it's place. */
> =A0 =A0 =A0 =A0while (bcom_buffer_done(s->bcom_task)) {
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0bcom_retrieve_buffer(s->bcom_task, NULL, N=
ULL);
> +
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0s->period_current_pt +=3D s->period_bytes;
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0if (s->period_current_pt >=3D s->period_en=
d)
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0s->period_current_pt =3D s=
->period_start;
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 psc_dma_bcom_enqueue_next_buffer(s);
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 bcom_enable(s->bcom_task);
> =A0 =A0 =A0 =A0}
> + =A0 =A0 =A0 psc_dma_bcom_enqueue_tx(s);
>
> =A0 =A0 =A0 =A0/* If the stream is active, then also inform the PCM middl=
e layer
> =A0 =A0 =A0 =A0 * of the period finished event. */
> @@ -105,49 +104,31 @@ static irqreturn_t psc_dma_bcom_irq(int irq, void *=
_psc_dma_stream)
> =A0 =A0 =A0 =A0return IRQ_HANDLED;
> =A0}
>
> -/**
> - * psc_dma_startup: create a new substream
> - *
> - * This is the first function called when a stream is opened.
> - *
> - * If this is the first stream open, then grab the IRQ and program most =
of
> - * the PSC registers.
> - */
> -int psc_dma_startup(struct snd_pcm_substream *substream,
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0struct snd_soc_dai *=
dai)
> +static irqreturn_t psc_dma_bcom_irq_rx(int irq, void *_psc_dma_stream)
> =A0{
> - =A0 =A0 =A0 struct snd_soc_pcm_runtime *rtd =3D substream->private_data=
;
> - =A0 =A0 =A0 struct psc_dma *psc_dma =3D rtd->dai->cpu_dai->private_data=
;
> - =A0 =A0 =A0 int rc;
> + =A0 =A0 =A0 struct psc_dma_stream *s =3D _psc_dma_stream;
>
> - =A0 =A0 =A0 dev_dbg(psc_dma->dev, "psc_dma_startup(substream=3D%p)\n", =
substream);
> + =A0 =A0 =A0 /* For each finished period, dequeue the completed period b=
uffer
> + =A0 =A0 =A0 =A0* and enqueue a new one in it's place. */
> + =A0 =A0 =A0 while (bcom_buffer_done(s->bcom_task)) {
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 bcom_retrieve_buffer(s->bcom_task, NULL, NU=
LL);
>
> - =A0 =A0 =A0 if (!psc_dma->playback.active &&
> - =A0 =A0 =A0 =A0 =A0 !psc_dma->capture.active) {
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 /* Setup the IRQs */
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 rc =3D request_irq(psc_dma->irq, &psc_dma_s=
tatus_irq, IRQF_SHARED,
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0"psc-dma=
-status", psc_dma);
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 rc |=3D request_irq(psc_dma->capture.irq,
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 &psc_dm=
a_bcom_irq, IRQF_SHARED,
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 "psc-dm=
a-capture", &psc_dma->capture);
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 rc |=3D request_irq(psc_dma->playback.irq,
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 &psc_dm=
a_bcom_irq, IRQF_SHARED,
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 "psc-dm=
a-playback", &psc_dma->playback);
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 if (rc) {
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 free_irq(psc_dma->irq, psc_=
dma);
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 free_irq(psc_dma->capture.i=
rq,
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0&psc_dma=
->capture);
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 free_irq(psc_dma->playback.=
irq,
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0&psc_dma=
->playback);
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 return -ENODEV;
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 }
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 s->period_current_pt +=3D s->period_bytes;
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 if (s->period_current_pt >=3D s->period_end=
)
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 s->period_current_pt =3D s-=
>period_start;
> +
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 psc_dma_bcom_enqueue_next_buffer(s);
> =A0 =A0 =A0 =A0}
>
> - =A0 =A0 =A0 return 0;
> + =A0 =A0 =A0 /* If the stream is active, then also inform the PCM middle=
layer
> + =A0 =A0 =A0 =A0* of the period finished event. */
> + =A0 =A0 =A0 if (s->active)
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 snd_pcm_period_elapsed(s->stream);
> +
> + =A0 =A0 =A0 return IRQ_HANDLED;
> =A0}
>
> -int psc_dma_hw_free(struct snd_pcm_substream *substream,
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0struct snd_soc_dai *=
dai)
> +static int psc_dma_hw_free(struct snd_pcm_substream *substream)
> =A0{
> =A0 =A0 =A0 =A0snd_pcm_set_runtime_buffer(substream, NULL);
> =A0 =A0 =A0 =A0return 0;
> @@ -159,8 +140,7 @@ int psc_dma_hw_free(struct snd_pcm_substream *substre=
am,
> =A0* This function is called by ALSA to start, stop, pause, and resume th=
e DMA
> =A0* transfer of data.
> =A0*/
> -int psc_dma_trigger(struct snd_pcm_substream *substream, int cmd,
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0struct snd_soc_dai *=
dai)
> +static int psc_dma_trigger(struct snd_pcm_substream *substream, int cmd)
> =A0{
> =A0 =A0 =A0 =A0struct snd_soc_pcm_runtime *rtd =3D substream->private_dat=
a;
> =A0 =A0 =A0 =A0struct psc_dma *psc_dma =3D rtd->dai->cpu_dai->private_dat=
a;
> @@ -168,8 +148,8 @@ int psc_dma_trigger(struct snd_pcm_substream *substre=
am, int cmd,
> =A0 =A0 =A0 =A0struct psc_dma_stream *s;
> =A0 =A0 =A0 =A0struct mpc52xx_psc __iomem *regs =3D psc_dma->psc_regs;
> =A0 =A0 =A0 =A0u16 imr;
> - =A0 =A0 =A0 u8 psc_cmd;
> =A0 =A0 =A0 =A0unsigned long flags;
> + =A0 =A0 =A0 int i;
>
> =A0 =A0 =A0 =A0if (substream->pstr->stream =3D=3D SNDRV_PCM_STREAM_CAPTUR=
E)
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0s =3D &psc_dma->capture;
> @@ -189,68 +169,45 @@ int psc_dma_trigger(struct snd_pcm_substream *subst=
ream, int cmd,
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0(s->period=
_bytes * runtime->periods);
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0s->period_next_pt =3D s->period_start;
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0s->period_current_pt =3D s->period_start;
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 s->period_size =3D runtime->period_size;
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0s->active =3D 1;
>
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 /* First; reset everything */
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 /* track appl_ptr so that we have a better =
chance of detecting
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0* end of stream and not over running it.
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0*/
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 s->runtime =3D runtime;
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 s->appl_ptr =3D s->runtime->control->appl_p=
tr -
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 (runtime->p=
eriod_size * runtime->periods);
> +
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 /* Fill up the bestcomm bd queue and enable=
DMA.
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0* This will begin filling the PSC's fifo=
.
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0*/
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0if (substream->pstr->stream =3D=3D SNDRV_P=
CM_STREAM_CAPTURE) {
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_8(®s->command, MPC52=
xx_PSC_RST_RX);
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_8(®s->command, MPC52=
xx_PSC_RST_ERR_STAT);
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 bcom_gen_bd_rx_reset(s->bco=
m_task);
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 for (i =3D 0; i < runtime->=
periods; i++)
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 if (!bcom_q=
ueue_full(s->bcom_task))
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0=
=A0 psc_dma_bcom_enqueue_next_buffer(s);
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0} else {
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_8(®s->command, MPC52=
xx_PSC_RST_TX);
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_8(®s->command, MPC52=
xx_PSC_RST_ERR_STAT);
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 bcom_gen_bd_tx_reset(s->bco=
m_task);
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 psc_dma_bcom_enqueue_tx(s);
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0}
>
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 /* Next, fill up the bestcomm bd queue and =
enable DMA.
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0* This will begin filling the PSC's fifo=
. */
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 if (substream->pstr->stream =3D=3D SNDRV_PC=
M_STREAM_CAPTURE)
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 bcom_gen_bd_rx_reset(s->bco=
m_task);
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 else
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 bcom_gen_bd_tx_reset(s->bco=
m_task);
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 while (!bcom_queue_full(s->bcom_task))
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 psc_dma_bcom_enqueue_next_b=
uffer(s);
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0bcom_enable(s->bcom_task);
>
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 /* Due to errata in the dma mode; need to l=
ine up enabling
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0* the transmitter with a transition on t=
he frame sync
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0* line */
> -
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0spin_lock_irqsave(&psc_dma->lock, flags);
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 /* first make sure it is low */
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 while ((in_8(®s->ipcr_acr.ipcr) & 0x80) =
!=3D 0)
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 ;
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 /* then wait for the transition to high */
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 while ((in_8(®s->ipcr_acr.ipcr) & 0x80) =
=3D=3D 0)
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 ;
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 /* Finally, enable the PSC.
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0* Receiver must always be enabled; even =
when we only want
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0* transmit. =A0(see 15.3.2.3 of MPC5200B=
User's Guide) */
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 psc_cmd =3D MPC52xx_PSC_RX_ENABLE;
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 if (substream->pstr->stream =3D=3D SNDRV_PC=
M_STREAM_PLAYBACK)
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 psc_cmd |=3D MPC52xx_PSC_TX=
_ENABLE;
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_8(®s->command, psc_cmd);
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_8(®s->command, MPC52xx_PSC_RST_ERR_S=
TAT);
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0spin_unlock_irqrestore(&psc_dma->lock, fla=
gs);
>
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0break;
>
> =A0 =A0 =A0 =A0case SNDRV_PCM_TRIGGER_STOP:
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 /* Turn off the PSC */
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0s->active =3D 0;
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 if (substream->pstr->stream =3D=3D SNDRV_PC=
M_STREAM_CAPTURE) {
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 if (!psc_dma->playback.acti=
ve) {
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_8(®s=
->command, 2 << 4); =A0/* reset rx */
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_8(®s=
->command, 3 << 4); =A0/* reset tx */
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_8(®s=
->command, 4 << 4); =A0/* reset err */
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 }
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 } else {
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_8(®s->command, 3 << =
4); =A0/* reset tx */
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_8(®s->command, 4 << =
4); =A0/* reset err */
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 if (!psc_dma->capture.activ=
e)
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_8(®s=
->command, 2 << 4); =A0/* reset rx */
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 }
>
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0bcom_disable(s->bcom_task);
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 while (!bcom_queue_empty(s->bcom_task))
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 bcom_retrieve_buffer(s->bco=
m_task, NULL, NULL);
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 if (substream->pstr->stream =3D=3D SNDRV_PC=
M_STREAM_CAPTURE)
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 bcom_gen_bd_rx_reset(s->bco=
m_task);
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 else
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 bcom_gen_bd_tx_reset(s->bco=
m_task);
>
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0break;
>
> @@ -265,44 +222,11 @@ int psc_dma_trigger(struct snd_pcm_substream *subst=
ream, int cmd,
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0imr |=3D MPC52xx_PSC_IMR_TXEMP;
> =A0 =A0 =A0 =A0if (psc_dma->capture.active)
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0imr |=3D MPC52xx_PSC_IMR_ORERR;
> - =A0 =A0 =A0 out_be16(®s->isr_imr.imr, imr);
> + =A0 =A0 =A0 out_be16(®s->isr_imr.imr, psc_dma->imr | imr);
>
> =A0 =A0 =A0 =A0return 0;
> =A0}
>
> -/**
> - * psc_dma_shutdown: shutdown the data transfer on a stream
> - *
> - * Shutdown the PSC if there are no other substreams open.
> - */
> -void psc_dma_shutdown(struct snd_pcm_substream *substream,
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0struct snd_soc_d=
ai *dai)
> -{
> - =A0 =A0 =A0 struct snd_soc_pcm_runtime *rtd =3D substream->private_data=
;
> - =A0 =A0 =A0 struct psc_dma *psc_dma =3D rtd->dai->cpu_dai->private_data=
;
> -
> - =A0 =A0 =A0 dev_dbg(psc_dma->dev, "psc_dma_shutdown(substream=3D%p)\n",=
substream);
> -
> - =A0 =A0 =A0 /*
> - =A0 =A0 =A0 =A0* If this is the last active substream, disable the PSC =
and release
> - =A0 =A0 =A0 =A0* the IRQ.
> - =A0 =A0 =A0 =A0*/
> - =A0 =A0 =A0 if (!psc_dma->playback.active &&
> - =A0 =A0 =A0 =A0 =A0 !psc_dma->capture.active) {
> -
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 /* Disable all interrupts and reset the PSC=
*/
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_be16(&psc_dma->psc_regs->isr_imr.imr, 0=
);
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_8(&psc_dma->psc_regs->command, 3 << 4);=
/* reset tx */
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_8(&psc_dma->psc_regs->command, 2 << 4);=
/* reset rx */
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_8(&psc_dma->psc_regs->command, 1 << 4);=
/* reset mode */
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 out_8(&psc_dma->psc_regs->command, 4 << 4);=
/* reset error */
> -
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 /* Release irqs */
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 free_irq(psc_dma->irq, psc_dma);
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 free_irq(psc_dma->capture.irq, &psc_dma->ca=
pture);
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 free_irq(psc_dma->playback.irq, &psc_dma->p=
layback);
> - =A0 =A0 =A0 }
> -}
>
> =A0/* -------------------------------------------------------------------=
--
> =A0* The PSC DMA 'ASoC platform' driver
> @@ -312,62 +236,78 @@ void psc_dma_shutdown(struct snd_pcm_substream *sub=
stream,
> =A0* interaction with the attached codec
> =A0*/
>
> -static const struct snd_pcm_hardware psc_dma_pcm_hardware =3D {
> +static const struct snd_pcm_hardware psc_dma_hardware =3D {
> =A0 =A0 =A0 =A0.info =3D SNDRV_PCM_INFO_MMAP | SNDRV_PCM_INFO_MMAP_VALID =
|
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0SNDRV_PCM_INFO_INTERLEAVED | SNDRV_PCM_INF=
O_BLOCK_TRANSFER |
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0SNDRV_PCM_INFO_BATCH,
> =A0 =A0 =A0 =A0.formats =3D SNDRV_PCM_FMTBIT_S8 | SNDRV_PCM_FMTBIT_S16_BE=
|
> - =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0SNDRV_PCM_FMTBIT_S24_BE | SNDRV_PCM_=
FMTBIT_S32_BE,
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 SNDRV_PCM_FMTBIT_S24_BE | SNDRV_PCM_FMTBIT_=
S32_BE,
Unrelated whitespace changes?
> +/* ---------------------------------------------------------------------
> + * Sysfs attributes for error monitoring
> + */
All this sysfs stuff should be dropped from this patch. It is an
abuse of sysfs and I never should have written it this way. Feel free
to put it in a separate patch so others can use it if they really need
it, but I'd like it to not be kept in mainline.
g.
--=20
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
^ permalink raw reply
* Re: Initialize DBCR0 for PPC440 targets
From: srikanth krishnakar @ 2009-05-25 6:30 UTC (permalink / raw)
To: grant.likely; +Cc: Linuxppc-dev
In-Reply-To: <6213bc560905192250w4caa84aem9c0dedb2eed72fea@mail.gmail.com>
Hello Grant,
Is there any conclusion of the below discussion:
http://www.nabble.com/Question-about-DBCR0-initialization-for-440-td2304904=
4.html
Xilinx target (virtex5) hangs (while running GDBServer & KGDB) without
the DBCR0 initialization.
Can you please comment on this ?
Thanks,
-Srikanth
On Wed, May 20, 2009 at 11:20 AM, srikanth krishnakar
<skrishnakar@gmail.com> wrote:
> Hi David,
>
> I am not sure how the IDM behaves on few of PPC440 targets which don't
> have boot loaders. I have a reference for your question:
>
> http://www.nabble.com/Question-about-DBCR0-initialization-for-440-td23049=
044.html
>
> Without this fix (given patch) I am facing problems with GDB, and
> further target hangs while running gdbserver !
>
> Thanks,
> Srikanth
>
> On Wed, May 20, 2009 at 5:23 AM, David Gibson
> <david@gibson.dropbear.id.au> wrote:
>> On Tue, May 19, 2009 at 06:38:53PM +0530, srikanth krishnakar wrote:
>>> Hi,
>>>
>>> kernel- 2.6.29
>>> Debug technique: KGDB
>>>
>>> The PowerPC kernel does not initialize the PPC440 DBCR0 register. This
>>> prevents the use of software breakpoints in case of internal debug
>>> mode. Looking into head_fsl_booke.S for initialization of DBCR0 is
>>> used by boot-loaders.
>>> It seems head_44x.S lacks this step of DBCR0 register initialization.
>>> So fixing this with initializing the DBCR0 register as shown below :
>>>
>>> Subject: [PATCH] powerpc: 44x: Initialize DBCR0 for targets not having
>>> bootloader
>>>
>>> The kernel does not initialize the PPC440 DBCR0 register.
>>> This prevents (among other things) the use of software
>>> breakpoints with GDB. The boot loaders probably do initialize
>>> this but few targets run without a boot loader
>>
>> Um.. how does this prevent the use of software breakpoints with gdb?
>> The trap instructions still work with IDM=3D=3D0.
>>
>> --
>> David Gibson =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0| I'll have my music=
baroque, and my code
>> david AT gibson.dropbear.id.au =A0| minimalist, thank you. =A0NOT _the_ =
_other_
>> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0| _way_ _=
around_!
>> http://www.ozlabs.org/~dgibson
>>
>
>
>
> --
> "The Good You Do, The Best You GET"
>
> Regards
> Srikanth Krishnakar
> **********************
>
--=20
"The Good You Do, The Best You GET"
Regards
Srikanth Krishnakar
**********************
^ permalink raw reply
* [PATCH] powerpc/pmac: Update PowerMac 32-bit defconfig
From: Benjamin Herrenschmidt @ 2009-05-25 6:34 UTC (permalink / raw)
To: linuxppc-dev
This mostly adds back AppleTouch support and adds CONFIG_HIGHMEM
by default.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
arch/powerpc/configs/pmac32_defconfig | 278 +++++++++++++++++++++++-----------
1 file changed, 195 insertions(+), 83 deletions(-)
--- linux-work.orig/arch/powerpc/configs/pmac32_defconfig 2009-05-25 14:54:05.000000000 +1000
+++ linux-work/arch/powerpc/configs/pmac32_defconfig 2009-05-25 14:54:08.000000000 +1000
@@ -1,7 +1,7 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.28-rc3
-# Tue Nov 11 19:36:51 2008
+# Linux kernel version: 2.6.30-rc7
+# Mon May 25 14:53:25 2009
#
# CONFIG_PPC64 is not set
@@ -14,6 +14,7 @@ CONFIG_6xx=y
# CONFIG_40x is not set
# CONFIG_44x is not set
# CONFIG_E200 is not set
+CONFIG_PPC_BOOK3S=y
CONFIG_PPC_FPU=y
CONFIG_ALTIVEC=y
CONFIG_PPC_STD_MMU=y
@@ -43,7 +44,7 @@ CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_PPC=y
CONFIG_EARLY_PRINTK=y
CONFIG_GENERIC_NVRAM=y
-CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_SCHED_OMIT_FRAME_POINTER=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_PPC_OF=y
CONFIG_OF=y
@@ -52,12 +53,14 @@ CONFIG_OF=y
CONFIG_AUDIT_ARCH=y
CONFIG_GENERIC_BUG=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_DTC=y
# CONFIG_DEFAULT_UIMAGE is not set
CONFIG_HIBERNATE_32=y
CONFIG_ARCH_HIBERNATION_POSSIBLE=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
# CONFIG_PPC_DCR_NATIVE is not set
# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
@@ -72,14 +75,24 @@ CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
+CONFIG_POSIX_MQUEUE_SYSCTL=y
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_CLASSIC_RCU=y
+# CONFIG_TREE_RCU is not set
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
-# CONFIG_CGROUPS is not set
# CONFIG_GROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
CONFIG_SYSFS_DEPRECATED=y
CONFIG_SYSFS_DEPRECATED_V2=y
# CONFIG_RELAY is not set
@@ -88,23 +101,27 @@ CONFIG_NAMESPACES=y
# CONFIG_IPC_NS is not set
# CONFIG_USER_NS is not set
# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+CONFIG_RD_BZIP2=y
+CONFIG_RD_LZMA=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
# CONFIG_EMBEDDED is not set
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
+# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
-# CONFIG_COMPAT_BRK is not set
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
@@ -114,10 +131,12 @@ CONFIG_AIO=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
CONFIG_SLUB_DEBUG=y
+# CONFIG_COMPAT_BRK is not set
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
+CONFIG_TRACEPOINTS=y
# CONFIG_MARKERS is not set
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
@@ -127,10 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
+# CONFIG_SLOW_WORK is not set
# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
# CONFIG_MODULE_FORCE_LOAD is not set
@@ -138,11 +157,8 @@ CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
-CONFIG_KMOD=y
CONFIG_BLOCK=y
CONFIG_LBD=y
-# CONFIG_BLK_DEV_IO_TRACE is not set
-CONFIG_LSF=y
CONFIG_BLK_DEV_BSG=y
# CONFIG_BLK_DEV_INTEGRITY is not set
@@ -158,14 +174,11 @@ CONFIG_DEFAULT_AS=y
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
-CONFIG_CLASSIC_RCU=y
CONFIG_FREEZER=y
#
# Platform support
#
-CONFIG_PPC_MULTIPLATFORM=y
-CONFIG_CLASSIC32=y
# CONFIG_PPC_CHRP is not set
# CONFIG_MPC5121_ADS is not set
# CONFIG_MPC5121_GENERIC is not set
@@ -178,7 +191,9 @@ CONFIG_PPC_PMAC=y
# CONFIG_PPC_83xx is not set
# CONFIG_PPC_86xx is not set
# CONFIG_EMBEDDED6xx is not set
+# CONFIG_AMIGAONE is not set
CONFIG_PPC_NATIVE=y
+CONFIG_PPC_OF_BOOT_TRAMPOLINE=y
# CONFIG_IPIC is not set
CONFIG_MPIC=y
# CONFIG_MPIC_WEIRD is not set
@@ -212,11 +227,12 @@ CONFIG_CPU_FREQ_PMAC=y
CONFIG_PPC601_SYNC_FIX=y
# CONFIG_TAU is not set
# CONFIG_FSL_ULI1575 is not set
+# CONFIG_SIMPLE_GPIO is not set
#
# Kernel options
#
-# CONFIG_HIGHMEM is not set
+CONFIG_HIGHMEM=y
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
@@ -239,6 +255,7 @@ CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
CONFIG_ARCH_HAS_WALK_MEMORY=y
CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
# CONFIG_KEXEC is not set
+# CONFIG_CRASH_DUMP is not set
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_SELECT_MEMORY_MODEL=y
@@ -250,12 +267,17 @@ CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_MIGRATION is not set
-# CONFIG_RESOURCES_64BIT is not set
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_VIRT_TO_BUS=y
CONFIG_UNEVICTABLE_LRU=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_PPC_4K_PAGES=y
+# CONFIG_PPC_16K_PAGES is not set
+# CONFIG_PPC_64K_PAGES is not set
+# CONFIG_PPC_256K_PAGES is not set
CONFIG_FORCE_MAX_ZONEORDER=11
CONFIG_PROC_DEVICETREE=y
# CONFIG_CMDLINE_BOOL is not set
@@ -288,6 +310,8 @@ CONFIG_ARCH_SUPPORTS_MSI=y
# CONFIG_PCI_MSI is not set
# CONFIG_PCI_LEGACY is not set
# CONFIG_PCI_DEBUG is not set
+# CONFIG_PCI_STUB is not set
+# CONFIG_PCI_IOV is not set
CONFIG_PCCARD=m
# CONFIG_PCMCIA_DEBUG is not set
CONFIG_PCMCIA=m
@@ -397,6 +421,8 @@ CONFIG_NETFILTER_XTABLES=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
# CONFIG_NETFILTER_XT_TARGET_CONNMARK is not set
# CONFIG_NETFILTER_XT_TARGET_DSCP is not set
+CONFIG_NETFILTER_XT_TARGET_HL=m
+# CONFIG_NETFILTER_XT_TARGET_LED is not set
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
@@ -405,6 +431,7 @@ CONFIG_NETFILTER_XT_TARGET_RATEEST=m
CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+# CONFIG_NETFILTER_XT_MATCH_CLUSTER is not set
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
# CONFIG_NETFILTER_XT_MATCH_CONNBYTES is not set
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
@@ -415,6 +442,7 @@ CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set
CONFIG_NETFILTER_XT_MATCH_HELPER=m
+CONFIG_NETFILTER_XT_MATCH_HL=m
CONFIG_NETFILTER_XT_MATCH_IPRANGE=m
CONFIG_NETFILTER_XT_MATCH_LENGTH=m
CONFIG_NETFILTER_XT_MATCH_LIMIT=m
@@ -478,17 +506,15 @@ CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
CONFIG_IP_DCCP=m
CONFIG_INET_DCCP_DIAG=m
-CONFIG_IP_DCCP_ACKVEC=y
#
# DCCP CCIDs Configuration (EXPERIMENTAL)
#
-CONFIG_IP_DCCP_CCID2=m
# CONFIG_IP_DCCP_CCID2_DEBUG is not set
-CONFIG_IP_DCCP_CCID3=m
+CONFIG_IP_DCCP_CCID3=y
# CONFIG_IP_DCCP_CCID3_DEBUG is not set
CONFIG_IP_DCCP_CCID3_RTO=100
-CONFIG_IP_DCCP_TFRC_LIB=m
+CONFIG_IP_DCCP_TFRC_LIB=y
#
# DCCP Kernel Hacking
@@ -508,13 +534,16 @@ CONFIG_IP_DCCP_TFRC_LIB=m
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
# CONFIG_NET_SCHED is not set
CONFIG_NET_CLS_ROUTE=y
+# CONFIG_DCB is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
+# CONFIG_NET_DROP_MONITOR is not set
# CONFIG_HAMRADIO is not set
# CONFIG_CAN is not set
CONFIG_IRDA=m
@@ -577,8 +606,6 @@ CONFIG_BT_HIDP=m
#
# Bluetooth device drivers
#
-CONFIG_BT_HCIUSB=m
-# CONFIG_BT_HCIUSB_SCO is not set
# CONFIG_BT_HCIBTUSB is not set
# CONFIG_BT_HCIUART is not set
CONFIG_BT_HCIBCM203X=m
@@ -590,31 +617,27 @@ CONFIG_BT_HCIBFUSB=m
# CONFIG_BT_HCIBTUART is not set
# CONFIG_BT_HCIVHCI is not set
# CONFIG_AF_RXRPC is not set
-# CONFIG_PHONET is not set
CONFIG_WIRELESS=y
CONFIG_CFG80211=m
-CONFIG_NL80211=y
+# CONFIG_CFG80211_REG_DEBUG is not set
CONFIG_WIRELESS_OLD_REGULATORY=y
CONFIG_WIRELESS_EXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
+# CONFIG_LIB80211 is not set
CONFIG_MAC80211=m
#
# Rate control algorithm selection
#
-CONFIG_MAC80211_RC_PID=y
-# CONFIG_MAC80211_RC_MINSTREL is not set
-CONFIG_MAC80211_RC_DEFAULT_PID=y
-# CONFIG_MAC80211_RC_DEFAULT_MINSTREL is not set
-CONFIG_MAC80211_RC_DEFAULT="pid"
+CONFIG_MAC80211_RC_MINSTREL=y
+# CONFIG_MAC80211_RC_DEFAULT_PID is not set
+CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y
+CONFIG_MAC80211_RC_DEFAULT="minstrel"
# CONFIG_MAC80211_MESH is not set
CONFIG_MAC80211_LEDS=y
+# CONFIG_MAC80211_DEBUGFS is not set
# CONFIG_MAC80211_DEBUG_MENU is not set
-CONFIG_IEEE80211=m
-# CONFIG_IEEE80211_DEBUG is not set
-CONFIG_IEEE80211_CRYPT_WEP=m
-CONFIG_IEEE80211_CRYPT_CCMP=m
-CONFIG_IEEE80211_CRYPT_TKIP=m
+# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
@@ -662,17 +685,27 @@ CONFIG_BLK_DEV_RAM_SIZE=4096
# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_PHANTOM is not set
-# CONFIG_EEPROM_93CX6 is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
+# CONFIG_ICS932S401 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
# CONFIG_HP_ILO is not set
+# CONFIG_ISL29003 is not set
+# CONFIG_C2PORT is not set
+
+#
+# EEPROM support
+#
+# CONFIG_EEPROM_AT24 is not set
+# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_93CX6 is not set
CONFIG_HAVE_IDE=y
CONFIG_IDE=y
#
# Please see Documentation/ide/ide.txt for help/info on IDE drives
#
+CONFIG_IDE_XFER_MODE=y
CONFIG_IDE_TIMINGS=y
CONFIG_IDE_ATAPI=y
# CONFIG_BLK_DEV_IDE_SATA is not set
@@ -684,7 +717,6 @@ CONFIG_BLK_DEV_IDECS=m
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y
# CONFIG_BLK_DEV_IDETAPE is not set
-CONFIG_BLK_DEV_IDESCSI=y
# CONFIG_IDE_TASK_IOCTL is not set
CONFIG_IDE_PROC_FS=y
@@ -714,6 +746,7 @@ CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT8172 is not set
# CONFIG_BLK_DEV_IT8213 is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
@@ -728,7 +761,6 @@ CONFIG_BLK_DEV_SL82C105=y
# CONFIG_BLK_DEV_TC86C001 is not set
CONFIG_BLK_DEV_IDE_PMAC=y
CONFIG_BLK_DEV_IDE_PMAC_ATA100FIRST=y
-CONFIG_BLK_DEV_IDEDMA_PMAC=y
CONFIG_BLK_DEV_IDEDMA=y
#
@@ -772,6 +804,7 @@ CONFIG_SCSI_FC_ATTRS=y
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
+# CONFIG_SCSI_CXGB3_ISCSI is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
@@ -791,8 +824,12 @@ CONFIG_SCSI_AIC7XXX_OLD=m
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
+# CONFIG_SCSI_MPT2SAS is not set
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_SCSI_BUSLOGIC is not set
+# CONFIG_LIBFC is not set
+# CONFIG_LIBFCOE is not set
+# CONFIG_FCOE is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
@@ -822,6 +859,7 @@ CONFIG_SCSI_MAC53C94=y
# CONFIG_SCSI_SRP is not set
# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set
# CONFIG_SCSI_DH is not set
+# CONFIG_SCSI_OSD_INITIATOR is not set
# CONFIG_ATA is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
@@ -881,6 +919,7 @@ CONFIG_THERM_ADT746X=m
# CONFIG_ANSLCD is not set
CONFIG_PMAC_RACKMETER=m
CONFIG_NETDEVICES=y
+CONFIG_COMPAT_NET_DEV_OPS=y
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
@@ -898,6 +937,8 @@ CONFIG_BMAC=y
CONFIG_SUNGEM=y
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_ETHOC is not set
+# CONFIG_DNET is not set
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
@@ -913,7 +954,6 @@ CONFIG_PCNET32=y
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_B44 is not set
# CONFIG_FORCEDETH is not set
-# CONFIG_EEPRO100 is not set
# CONFIG_E100 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
@@ -923,6 +963,7 @@ CONFIG_PCNET32=y
# CONFIG_R6040 is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
+# CONFIG_SMSC9420 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
@@ -935,6 +976,7 @@ CONFIG_NETDEV_1000=y
# CONFIG_E1000E is not set
# CONFIG_IP1000 is not set
# CONFIG_IGB is not set
+# CONFIG_IGBVF is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
@@ -945,18 +987,20 @@ CONFIG_NETDEV_1000=y
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
-# CONFIG_MV643XX_ETH is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_ATL1E is not set
+# CONFIG_ATL1C is not set
# CONFIG_JME is not set
CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
+CONFIG_CHELSIO_T3_DEPENDS=y
# CONFIG_CHELSIO_T3 is not set
# CONFIG_ENIC is not set
# CONFIG_IXGBE is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
+# CONFIG_VXGE is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
# CONFIG_NIU is not set
@@ -966,6 +1010,7 @@ CONFIG_NETDEV_10000=y
# CONFIG_BNX2X is not set
# CONFIG_QLGE is not set
# CONFIG_SFC is not set
+# CONFIG_BE2NET is not set
# CONFIG_TR is not set
#
@@ -974,20 +1019,11 @@ CONFIG_NETDEV_10000=y
# CONFIG_WLAN_PRE80211 is not set
CONFIG_WLAN_80211=y
# CONFIG_PCMCIA_RAYCS is not set
-# CONFIG_IPW2100 is not set
-# CONFIG_IPW2200 is not set
# CONFIG_LIBERTAS is not set
# CONFIG_LIBERTAS_THINFIRM is not set
# CONFIG_AIRO is not set
-CONFIG_HERMES=m
-CONFIG_APPLE_AIRPORT=m
-# CONFIG_PLX_HERMES is not set
-# CONFIG_TMD_HERMES is not set
-# CONFIG_NORTEL_HERMES is not set
-CONFIG_PCI_HERMES=m
-CONFIG_PCMCIA_HERMES=m
-# CONFIG_PCMCIA_SPECTRUM is not set
# CONFIG_ATMEL is not set
+# CONFIG_AT76C50X_USB is not set
# CONFIG_AIRO_CS is not set
# CONFIG_PCMCIA_WL3501 is not set
CONFIG_PRISM54=m
@@ -997,15 +1033,17 @@ CONFIG_PRISM54=m
# CONFIG_RTL8187 is not set
# CONFIG_ADM8211 is not set
# CONFIG_MAC80211_HWSIM is not set
+# CONFIG_MWL8K is not set
CONFIG_P54_COMMON=m
# CONFIG_P54_USB is not set
# CONFIG_P54_PCI is not set
+CONFIG_P54_LEDS=y
# CONFIG_ATH5K is not set
# CONFIG_ATH9K is not set
-# CONFIG_IWLCORE is not set
-# CONFIG_IWLWIFI_LEDS is not set
-# CONFIG_IWLAGN is not set
-# CONFIG_IWL3945 is not set
+# CONFIG_AR9170_USB is not set
+# CONFIG_IPW2100 is not set
+# CONFIG_IPW2200 is not set
+# CONFIG_IWLWIFI is not set
# CONFIG_HOSTAP is not set
CONFIG_B43=m
CONFIG_B43_PCI_AUTOSELECT=y
@@ -1025,6 +1063,19 @@ CONFIG_B43LEGACY_DMA_AND_PIO_MODE=y
# CONFIG_B43LEGACY_PIO_MODE is not set
# CONFIG_ZD1211RW is not set
# CONFIG_RT2X00 is not set
+CONFIG_HERMES=m
+CONFIG_HERMES_CACHE_FW_ON_INIT=y
+CONFIG_APPLE_AIRPORT=m
+# CONFIG_PLX_HERMES is not set
+# CONFIG_TMD_HERMES is not set
+# CONFIG_NORTEL_HERMES is not set
+CONFIG_PCI_HERMES=m
+CONFIG_PCMCIA_HERMES=m
+# CONFIG_PCMCIA_SPECTRUM is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
#
# USB Network Adapters
@@ -1036,6 +1087,7 @@ CONFIG_B43LEGACY_DMA_AND_PIO_MODE=y
CONFIG_USB_USBNET=m
CONFIG_USB_NET_AX8817X=m
CONFIG_USB_NET_CDCETHER=m
+# CONFIG_USB_NET_CDC_EEM is not set
# CONFIG_USB_NET_DM9601 is not set
# CONFIG_USB_NET_SMSC95XX is not set
# CONFIG_USB_NET_GL620A is not set
@@ -1099,7 +1151,7 @@ CONFIG_INPUT_KEYBOARD=y
CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_PS2 is not set
# CONFIG_MOUSE_SERIAL is not set
-# CONFIG_MOUSE_APPLETOUCH is not set
+CONFIG_MOUSE_APPLETOUCH=y
# CONFIG_MOUSE_BCM5974 is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
@@ -1150,10 +1202,13 @@ CONFIG_SERIAL_PMACZILOG_TTYS=y
# CONFIG_SERIAL_JSM is not set
# CONFIG_SERIAL_OF_PLATFORM is not set
CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_HVC_UDBG is not set
# CONFIG_IPMI_HANDLER is not set
CONFIG_HW_RANDOM=m
+# CONFIG_HW_RANDOM_TIMERIOMEM is not set
CONFIG_NVRAM=y
CONFIG_GEN_RTC=y
# CONFIG_GEN_RTC_X is not set
@@ -1232,12 +1287,9 @@ CONFIG_I2C_POWERMAC=y
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_EEPROM_AT24 is not set
-# CONFIG_EEPROM_LEGACY is not set
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_PCF8575 is not set
# CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
@@ -1259,11 +1311,11 @@ CONFIG_BATTERY_PMU=y
# CONFIG_THERMAL is not set
# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
#
# Sonics Silicon Backplane
#
-CONFIG_SSB_POSSIBLE=y
CONFIG_SSB=m
CONFIG_SSB_SPROM=y
CONFIG_SSB_PCIHOST_POSSIBLE=y
@@ -1281,18 +1333,13 @@ CONFIG_SSB_DRIVER_PCICORE=y
# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TWL4030_CORE is not set
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
# CONFIG_MFD_WM8350_I2C is not set
-
-#
-# Voltage and Current regulators
-#
+# CONFIG_MFD_PCF50633 is not set
# CONFIG_REGULATOR is not set
-# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
-# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
-# CONFIG_REGULATOR_BQ24022 is not set
#
# Multimedia devices
@@ -1390,6 +1437,7 @@ CONFIG_FB_ATY_BACKLIGHT=y
# CONFIG_FB_KYRO is not set
CONFIG_FB_3DFX=y
# CONFIG_FB_3DFX_ACCEL is not set
+CONFIG_FB_3DFX_I2C=y
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_VT8623 is not set
# CONFIG_FB_TRIDENT is not set
@@ -1399,12 +1447,14 @@ CONFIG_FB_3DFX=y
# CONFIG_FB_IBM_GXT4500 is not set
# CONFIG_FB_VIRTUAL is not set
# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=m
# CONFIG_LCD_ILI9320 is not set
# CONFIG_LCD_PLATFORM is not set
CONFIG_BACKLIGHT_CLASS_DEVICE=y
-# CONFIG_BACKLIGHT_CORGI is not set
+CONFIG_BACKLIGHT_GENERIC=y
#
# Display device support
@@ -1444,11 +1494,13 @@ CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_PCM_OSS_PLUGINS=y
CONFIG_SND_SEQUENCER_OSS=y
+# CONFIG_SND_HRTIMER is not set
# CONFIG_SND_DYNAMIC_MINORS is not set
CONFIG_SND_SUPPORT_OLD_API=y
CONFIG_SND_VERBOSE_PROCFS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
+CONFIG_SND_VMASTER=y
CONFIG_SND_DRIVERS=y
CONFIG_SND_DUMMY=m
# CONFIG_SND_VIRMIDI is not set
@@ -1486,6 +1538,8 @@ CONFIG_SND_PCI=y
# CONFIG_SND_INDIGO is not set
# CONFIG_SND_INDIGOIO is not set
# CONFIG_SND_INDIGODJ is not set
+# CONFIG_SND_INDIGOIOX is not set
+# CONFIG_SND_INDIGODJX is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_ENS1370 is not set
@@ -1551,28 +1605,31 @@ CONFIG_USB_HID=y
#
# Special HID drivers
#
-CONFIG_HID_COMPAT=y
CONFIG_HID_A4TECH=y
CONFIG_HID_APPLE=y
CONFIG_HID_BELKIN=y
-CONFIG_HID_BRIGHT=y
CONFIG_HID_CHERRY=y
CONFIG_HID_CHICONY=y
CONFIG_HID_CYPRESS=y
-CONFIG_HID_DELL=y
+# CONFIG_DRAGONRISE_FF is not set
CONFIG_HID_EZKEY=y
+CONFIG_HID_KYE=y
CONFIG_HID_GYRATION=y
+CONFIG_HID_KENSINGTON=y
CONFIG_HID_LOGITECH=y
# CONFIG_LOGITECH_FF is not set
# CONFIG_LOGIRUMBLEPAD2_FF is not set
CONFIG_HID_MICROSOFT=y
CONFIG_HID_MONTEREY=y
+CONFIG_HID_NTRIG=y
CONFIG_HID_PANTHERLORD=y
# CONFIG_PANTHERLORD_FF is not set
CONFIG_HID_PETALYNX=y
CONFIG_HID_SAMSUNG=y
CONFIG_HID_SONY=y
CONFIG_HID_SUNPLUS=y
+# CONFIG_GREENASIA_FF is not set
+CONFIG_HID_TOPSEED=y
# CONFIG_THRUSTMASTER_FF is not set
# CONFIG_ZEROPLUS_FF is not set
CONFIG_USB_SUPPORT=y
@@ -1603,6 +1660,7 @@ CONFIG_USB_EHCI_HCD=m
CONFIG_USB_EHCI_ROOT_HUB_TT=y
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
# CONFIG_USB_EHCI_HCD_PPC_OF is not set
+# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
CONFIG_USB_OHCI_HCD=y
@@ -1625,24 +1683,23 @@ CONFIG_USB_PRINTER=m
# CONFIG_USB_TMC is not set
#
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
#
#
-# may also be needed; see USB_STORAGE Help for more information
+# also be needed; see USB_STORAGE Help for more info
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
-# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_USBAT is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
-CONFIG_USB_STORAGE_ONETOUCH=y
+CONFIG_USB_STORAGE_ONETOUCH=m
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
# CONFIG_USB_LIBUSUAL is not set
@@ -1665,7 +1722,7 @@ CONFIG_USB_EZUSB=y
# CONFIG_USB_SERIAL_CH341 is not set
# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
-# CONFIG_USB_SERIAL_CP2101 is not set
+# CONFIG_USB_SERIAL_CP210X is not set
# CONFIG_USB_SERIAL_CYPRESS_M8 is not set
# CONFIG_USB_SERIAL_EMPEG is not set
# CONFIG_USB_SERIAL_FTDI_SIO is not set
@@ -1701,15 +1758,19 @@ CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
# CONFIG_USB_SERIAL_NAVMAN is not set
# CONFIG_USB_SERIAL_PL2303 is not set
# CONFIG_USB_SERIAL_OTI6858 is not set
+# CONFIG_USB_SERIAL_QUALCOMM is not set
# CONFIG_USB_SERIAL_SPCP8X5 is not set
# CONFIG_USB_SERIAL_HP4X is not set
# CONFIG_USB_SERIAL_SAFE is not set
+# CONFIG_USB_SERIAL_SIEMENS_MPI is not set
# CONFIG_USB_SERIAL_SIERRAWIRELESS is not set
+# CONFIG_USB_SERIAL_SYMBOL is not set
# CONFIG_USB_SERIAL_TI is not set
# CONFIG_USB_SERIAL_CYBERJACK is not set
# CONFIG_USB_SERIAL_XIRCOM is not set
# CONFIG_USB_SERIAL_OPTION is not set
# CONFIG_USB_SERIAL_OMNINET is not set
+# CONFIG_USB_SERIAL_OPTICON is not set
# CONFIG_USB_SERIAL_DEBUG is not set
#
@@ -1726,7 +1787,6 @@ CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
-# CONFIG_USB_PHIDGET is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_FTDI_ELAN is not set
CONFIG_USB_APPLEDISPLAY=m
@@ -1738,6 +1798,11 @@ CONFIG_USB_APPLEDISPLAY=m
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_VST is not set
# CONFIG_USB_GADGET is not set
+
+#
+# OTG and related infrastructure
+#
+# CONFIG_NOP_USB_XCEIV is not set
# CONFIG_UWB is not set
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not set
@@ -1748,7 +1813,9 @@ CONFIG_LEDS_CLASS=y
# LED drivers
#
# CONFIG_LEDS_PCA9532 is not set
+# CONFIG_LEDS_LP5521 is not set
# CONFIG_LEDS_PCA955X is not set
+# CONFIG_LEDS_BD2802 is not set
#
# LED Triggers
@@ -1759,11 +1826,16 @@ CONFIG_LEDS_TRIGGER_IDE_DISK=y
# CONFIG_LEDS_TRIGGER_HEARTBEAT is not set
# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+
+#
+# iptables trigger is under Netfilter config (LED target)
+#
# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
# CONFIG_RTC_CLASS is not set
# CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
# CONFIG_UIO is not set
# CONFIG_STAGING is not set
@@ -1774,6 +1846,7 @@ CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
# CONFIG_EXT3_FS_SECURITY is not set
@@ -1783,7 +1856,9 @@ CONFIG_EXT4_FS_XATTR=y
# CONFIG_EXT4_FS_POSIX_ACL is not set
# CONFIG_EXT4_FS_SECURITY is not set
CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
CONFIG_JBD2=y
+# CONFIG_JBD2_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
@@ -1792,6 +1867,7 @@ CONFIG_FILE_LOCKING=y
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
@@ -1801,6 +1877,11 @@ CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m
#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
@@ -1831,10 +1912,7 @@ CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
+CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
CONFIG_HFS_FS=m
@@ -1843,6 +1921,7 @@ CONFIG_HFSPLUS_FS=m
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
+# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_OMFS_FS is not set
@@ -1851,6 +1930,7 @@ CONFIG_HFSPLUS_FS=m
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
@@ -1868,7 +1948,6 @@ CONFIG_NFS_ACL_SUPPORT=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
-# CONFIG_SUNRPC_REGISTER_V4 is not set
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
@@ -1940,11 +2019,13 @@ CONFIG_NLS_ISO8859_1=m
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=m
# CONFIG_DLM is not set
+CONFIG_BINARY_PRINTF=y
#
# Library routines
#
CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
CONFIG_CRC_CCITT=y
CONFIG_CRC16=y
CONFIG_CRC_T10DIF=y
@@ -1954,15 +2035,18 @@ CONFIG_CRC32=y
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_DECOMPRESS_BZIP2=y
+CONFIG_DECOMPRESS_LZMA=y
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_TEXTSEARCH_BM=m
CONFIG_TEXTSEARCH_FSM=m
-CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
CONFIG_HAVE_LMB=y
+CONFIG_NLATTR=y
#
# Kernel hacking
@@ -1973,13 +2057,16 @@ CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
+CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
CONFIG_SCHED_DEBUG=y
CONFIG_SCHEDSTATS=y
# CONFIG_TIMER_STATS is not set
@@ -1994,6 +2081,7 @@ CONFIG_SCHEDSTATS=y
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
CONFIG_STACKTRACE=y
# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_HIGHMEM is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_VM is not set
@@ -2001,6 +2089,7 @@ CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_MEMORY_INIT=y
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
@@ -2009,7 +2098,14 @@ CONFIG_DEBUG_MEMORY_INIT=y
# CONFIG_FAULT_INJECTION is not set
CONFIG_LATENCYTOP=y
CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_RING_BUFFER=y
+CONFIG_TRACING=y
+CONFIG_TRACING_SUPPORT=y
#
# Tracers
@@ -2017,12 +2113,19 @@ CONFIG_HAVE_FUNCTION_TRACER=y
# CONFIG_FUNCTION_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_CONTEXT_SWITCH_TRACER is not set
+# CONFIG_EVENT_TRACER is not set
# CONFIG_BOOT_TRACER is not set
+# CONFIG_TRACE_BRANCH_PROFILING is not set
# CONFIG_STACK_TRACER is not set
-# CONFIG_DYNAMIC_PRINTK_DEBUG is not set
+# CONFIG_KMEMTRACE is not set
+# CONFIG_WORKQUEUE_TRACER is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE_STARTUP_TEST is not set
+# CONFIG_DYNAMIC_DEBUG is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
+CONFIG_PRINT_STACK_DEPTH=64
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_CODE_PATCHING_SELFTEST is not set
@@ -2033,6 +2136,7 @@ CONFIG_XMON_DEFAULT=y
CONFIG_XMON_DISASSEMBLY=y
CONFIG_DEBUGGER=y
CONFIG_IRQSTACKS=y
+# CONFIG_VIRQ_DEBUG is not set
# CONFIG_BDI_SWITCH is not set
CONFIG_BOOTX_TEXT=y
# CONFIG_PPC_EARLY_DEBUG is not set
@@ -2051,13 +2155,20 @@ CONFIG_CRYPTO=y
#
# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD=y
+CONFIG_CRYPTO_AEAD2=y
CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
CONFIG_CRYPTO_HASH=y
-CONFIG_CRYPTO_RNG=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_PCOMP=y
CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
# CONFIG_CRYPTO_GF128MUL is not set
CONFIG_CRYPTO_NULL=m
+CONFIG_CRYPTO_WORKQUEUE=y
# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_AUTHENC=y
# CONFIG_CRYPTO_TEST is not set
@@ -2127,6 +2238,7 @@ CONFIG_CRYPTO_TWOFISH_COMMON=m
# Compression
#
CONFIG_CRYPTO_DEFLATE=m
+# CONFIG_CRYPTO_ZLIB is not set
# CONFIG_CRYPTO_LZO is not set
#
^ permalink raw reply
* Re: [PATCH V3 3/4] Support for AC97 on Phytec pmc030 base board.
From: Grant Likely @ 2009-05-25 6:34 UTC (permalink / raw)
To: Jon Smirl; +Cc: linuxppc-dev, alsa-devel, broonie
In-Reply-To: <20090525013851.3073.79847.stgit@terra>
On Sun, May 24, 2009 at 7:38 PM, Jon Smirl <jonsmirl@gmail.com> wrote:
> Support for AC97 on Phytec pmc030 base board. A wm9712 AC97 codec is used=
.
>
> Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
> ---
> =A0sound/soc/fsl/Kconfig =A0 =A0 =A0 =A0 =A0 =A0 =A0 | =A0 =A07 +++
> =A0sound/soc/fsl/Makefile =A0 =A0 =A0 =A0 =A0 =A0 =A0| =A0 =A03 +
> =A0sound/soc/fsl/pcm030-audio-fabric.c | =A0 95 +++++++++++++++++++++++++=
++++++++++
> =A03 files changed, 105 insertions(+), 0 deletions(-)
> =A0create mode 100644 sound/soc/fsl/pcm030-audio-fabric.c
>
> diff --git a/sound/soc/fsl/Kconfig b/sound/soc/fsl/Kconfig
> index 3bce952..79579ae 100644
> --- a/sound/soc/fsl/Kconfig
> +++ b/sound/soc/fsl/Kconfig
> @@ -39,4 +39,11 @@ config SND_SOC_MPC5200_AC97
> =A0 =A0 =A0 =A0help
> =A0 =A0 =A0 =A0 =A0Say Y here to support the MPC5200 PSCs in AC97 mode.
>
> +config SND_MPC52xx_SOC_PCM030
> + =A0 =A0 =A0 tristate "SoC AC97 Audio support for Phytec pcm030 and WM97=
12"
> + =A0 =A0 =A0 depends on PPC_MPC5200_SIMPLE
> + =A0 =A0 =A0 select SND_SOC_MPC5200_AC97
> + =A0 =A0 =A0 select SND_SOC_WM9712
> + =A0 =A0 =A0 help
> + =A0 =A0 =A0 =A0 Say Y if you want to add support for sound on the Phyte=
c pcm030 baseboard.
>
> diff --git a/sound/soc/fsl/Makefile b/sound/soc/fsl/Makefile
> index 14631a1..66d88c8 100644
> --- a/sound/soc/fsl/Makefile
> +++ b/sound/soc/fsl/Makefile
> @@ -15,3 +15,6 @@ obj-$(CONFIG_SND_MPC52xx_DMA) +=3D mpc5200_dma.o
> =A0obj-$(CONFIG_SND_SOC_MPC5200_I2S) +=3D mpc5200_psc_i2s.o
> =A0obj-$(CONFIG_SND_SOC_MPC5200_AC97) +=3D mpc5200_psc_ac97.o
>
> +# MPC5200 Machine Support
> +obj-$(CONFIG_SND_MPC52xx_SOC_PCM030) +=3D pcm030-audio-fabric.o
> +
> diff --git a/sound/soc/fsl/pcm030-audio-fabric.c b/sound/soc/fsl/pcm030-a=
udio-fabric.c
> new file mode 100644
> index 0000000..2c426d5
> --- /dev/null
> +++ b/sound/soc/fsl/pcm030-audio-fabric.c
> @@ -0,0 +1,95 @@
> +/*
> + * Phytec pcm030 driver for the PSC of the Freescale MPC52xx
> + * configured as AC97 interface
> + *
> + * Copyright 2008 Jon Smirl, Digispeaker
> + * Author: Jon Smirl <jonsmirl@gmail.com>
> + *
> + * This file is licensed under the terms of the GNU General Public Licen=
se
> + * version 2. This program is licensed "as is" without any warranty of a=
ny
> + * kind, whether express or implied.
> + */
> +
> +#include <linux/init.h>
> +#include <linux/module.h>
> +#include <linux/interrupt.h>
> +#include <linux/device.h>
> +#include <linux/delay.h>
> +#include <linux/of_device.h>
> +#include <linux/of_platform.h>
> +#include <linux/dma-mapping.h>
> +
> +#include <sound/core.h>
> +#include <sound/pcm.h>
> +#include <sound/pcm_params.h>
> +#include <sound/initval.h>
> +#include <sound/soc.h>
> +#include <sound/soc-of-simple.h>
> +
> +#include "mpc5200_dma.h"
> +#include "mpc5200_psc_ac97.h"
> +#include "../codecs/wm9712.h"
> +
> +static struct snd_soc_device device;
> +static struct snd_soc_card card;
> +
> +static struct snd_soc_dai_link pcm030_fabric_dai[] =3D {
> +{
> + =A0 =A0 =A0 .name =3D "AC97",
> + =A0 =A0 =A0 .stream_name =3D "AC97 Analog",
> + =A0 =A0 =A0 .codec_dai =3D &wm9712_dai[WM9712_DAI_AC97_HIFI],
> + =A0 =A0 =A0 .cpu_dai =3D &psc_ac97_dai[MPC5200_AC97_NORMAL],
> +},
> +{
> + =A0 =A0 =A0 .name =3D "AC97",
> + =A0 =A0 =A0 .stream_name =3D "AC97 IEC958",
> + =A0 =A0 =A0 .codec_dai =3D &wm9712_dai[WM9712_DAI_AC97_AUX],
> + =A0 =A0 =A0 .cpu_dai =3D &psc_ac97_dai[MPC5200_AC97_SPDIF],
> +},
> +};
> +
> +static __init int pcm030_fabric_init(void)
> +{
> + =A0 =A0 =A0 struct platform_device *pdev;
> + =A0 =A0 =A0 int rc;
> +
> + =A0 =A0 =A0 if (!machine_is_compatible("phytec,pcm030"))
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 return -ENODEV;
> +
> + =A0 =A0 =A0 card.platform =3D &mpc5200_audio_dma_platform;
> + =A0 =A0 =A0 card.name =3D "pcm030";
> + =A0 =A0 =A0 card.dai_link =3D pcm030_fabric_dai;
> + =A0 =A0 =A0 card.num_links =3D ARRAY_SIZE(pcm030_fabric_dai);
> +
> + =A0 =A0 =A0 device.card =3D &card;
> + =A0 =A0 =A0 device.codec_dev =3D &soc_codec_dev_wm9712;
> +
> + =A0 =A0 =A0 pdev =3D platform_device_alloc("soc-audio", 1);
> + =A0 =A0 =A0 if (!pdev) {
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 pr_err("pcm030_fabric_init: platform_device=
_alloc() failed\n");
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 return -ENODEV;
> + =A0 =A0 =A0 }
> +
> + =A0 =A0 =A0 platform_set_drvdata(pdev, &device);
> + =A0 =A0 =A0 device.dev =3D &pdev->dev;
> +
> + =A0 =A0 =A0 rc =3D platform_device_add(pdev);
> + =A0 =A0 =A0 if (rc) {
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 pr_err("pcm030_fabric_init: platform_device=
_add() failed\n");
> + =A0 =A0 =A0 =A0 =A0 =A0 =A0 return -ENODEV;
> + =A0 =A0 =A0 }
> + =A0 =A0 =A0 return 0;
> +}
This is ugly. I'd really rather have a generic mechanism for creating
a fabric driver based on the OF data. But failing that, it seems to
me that this platform device registration should be done in the
platform code (arch/powerpc/platforms/52xx). Doing it in a module
init looks wrong.
I was trying to do a sort of generic matching mechanism with the of
simple stuff; but admittedly it was hacky and half-assed. However, I
do still think it is viable to have OF hooks that kick in when codec
and machine drivers are registered. If linkage data is encoded in the
device tree, then generic code should be able to hook them up; pulling
additional data out of the device tree as needed to configure the
coded.
g.
--=20
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
^ permalink raw reply
* Re: Initialize DBCR0 for PPC440 targets
From: Grant Likely @ 2009-05-25 6:39 UTC (permalink / raw)
To: srikanth krishnakar; +Cc: Linuxppc-dev, John Linn
In-Reply-To: <6213bc560905242330j31c14d22pabb67174e105d68c@mail.gmail.com>
On Mon, May 25, 2009 at 12:30 AM, srikanth krishnakar
<skrishnakar@gmail.com> wrote:
> Hello Grant,
>
> Is there any conclusion of the below discussion:
>
> http://www.nabble.com/Question-about-DBCR0-initialization-for-440-td23049044.html
>
> Xilinx target (virtex5) hangs (while running GDBServer & KGDB) without
> the DBCR0 initialization.
>
> Can you please comment on this ?
IIRC, John Linn was hacking on a patch. Search the mailing list
archives for DBCR0.
g.
--
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
^ permalink raw reply
* Re: powerpc: DMA coherent allocations broken for CONFIG_NOT_COHERENT_CACHE
From: Benjamin Herrenschmidt @ 2009-05-25 6:49 UTC (permalink / raw)
To: Grant Likely; +Cc: linuxppc-dev list, Albert Herranz, Ilya Yanok, Kumar Gala
In-Reply-To: <fa686aa40905242250g2a627c32s2b4c2ed06abd5dc4@mail.gmail.com>
On Sun, 2009-05-24 at 23:50 -0600, Grant Likely wrote:
> It would also be nice for comprehension if the file move and the
> modification were separate commits. As it is I had to generate the
> diff manually, but I'm not concerned.
Right, I though about that... too late :-) might break it up tomorrow
morning, I don't have time to fix that up right now. Hopefully Kumar
and Ilya will manage to do the same you did to diff it :-)
Cheers,
Ben.
^ permalink raw reply
* Re: Initialize DBCR0 for PPC440 targets
From: srikanth krishnakar @ 2009-05-25 6:51 UTC (permalink / raw)
To: John Linn; +Cc: Linuxppc-dev
In-Reply-To: <fa686aa40905242339l51ee5656ue388cde6da253287@mail.gmail.com>
Hi John,
I am not finding any conclusion of the plan to add DBCR0
initialization code to head_44x.S after this discussion :
http://www.nabble.com/Question-about-DBCR0-initialization-for-440-td2304904=
4.html#a23049044
Can you please comment ?
Thanks,
-Srikanth Krishnakar
On Mon, May 25, 2009 at 12:09 PM, Grant Likely
<grant.likely@secretlab.ca> wrote:
> On Mon, May 25, 2009 at 12:30 AM, srikanth krishnakar
> <skrishnakar@gmail.com> wrote:
>> Hello Grant,
>>
>> Is there any conclusion of the below discussion:
>>
>> http://www.nabble.com/Question-about-DBCR0-initialization-for-440-td2304=
9044.html
>>
>> Xilinx target (virtex5) hangs (while running GDBServer & KGDB) without
>> the DBCR0 initialization.
>>
>> Can you please comment on this ?
>
> IIRC, John Linn was hacking on a patch. =A0Search the mailing list
> archives for DBCR0.
>
> g.
>
> --
> Grant Likely, B.Sc., P.Eng.
> Secret Lab Technologies Ltd.
>
--=20
"The Good You Do, The Best You GET"
Regards
Srikanth Krishnakar
**********************
^ permalink raw reply
* Re: [net-next-2.6 PATCH v2] can: SJA1000: generic OF platform bus driver
From: Grant Likely @ 2009-05-25 6:53 UTC (permalink / raw)
To: Wolfgang Grandegger, Segher Boessenkool
Cc: Linux Netdev List, devicetree-discuss, linuxppc-dev
In-Reply-To: <4A182800.2090204@grandegger.com>
On Sat, May 23, 2009 at 10:44 AM, Wolfgang Grandegger <wg@grandegger.com> w=
rote:
> Wolfgang Grandegger wrote:
>> Grant Likely wrote:
>>>> +- clock-frequency : CAN system clock frequency in Hz, which is normal=
ly
>>>> + =A0 =A0 =A0 half of the oscillator clock frequency. If not specified=
, a
>>>> + =A0 =A0 =A0 default value of 8000000 (8 MHz) is used.
>>> A clock-frequency property typically refers to the bus clock
>>> frequency. =A0Something like can-frequency would be better.
>>
>> Ah, right, but I'm also not happy with "can-frequency". The manual
>> speaks about the "internal clock", which is half of the external
>> oscillator frequency. Maybe "internal-clock-frequency" might be better.
Would it be better to specify the external clock frequency, and the
driver know that internal freq is half that? I ask because external
clock freq is a value the HW designer actually has control over.
>>>> +- cdr-reg : value of the SJA1000 clock divider register according to
>>>> + =A0 =A0 =A0 the SJA1000 data sheet. If not specified, a default valu=
e of
>>>> + =A0 =A0 =A0 0x48 is used.
>>> Ewh. =A0The driver should be clueful enough to derive the clock divider
>>> value given both the bus and can frequencies. =A0I don't like this
>>> property.
>>
>> The clock divider register controls the CLKOUT frequency for the
>> microcontroller another CAN controller and allows to deactivate the
>> CLKOUT pin. It's not used to configure the CAN bus frequency.
>>
>>>> +- ocr-reg : value of the SJA1000 output control register according to
>>>> + =A0 =A0 =A0 the SJA1000 data sheet. If not specified, a default valu=
e of
>>>> + =A0 =A0 =A0 0x0a is used.
>>> Ditto here; the binding should describe the usage mode; not the
>>> register settings to get the usage mode. =A0What sort of settings will
>>> the .dts author be writing here?
>>
>> Unfortunately, there are many:
>>
>> clkout-frequency
>> bypass-comperator
>> tx1-output-on-rx-irq
>>
>> #define OCR_MODE_BIPHASE =A00x00
>> #define OCR_MODE_TEST =A0 =A0 0x01
>> #define OCR_MODE_NORMAL =A0 0x02
>> #define OCR_MODE_CLOCK =A0 =A00x03
>>
>> #define OCR_TX0_INVERT =A0 =A00x04
>> #define OCR_TX0_PULLDOWN =A00x08
>> #define OCR_TX0_PULLUP =A0 =A00x10
>> #define OCR_TX0_PUSHPULL =A00x18
>> #define OCR_TX1_INVERT =A0 =A00x20
>> #define OCR_TX1_PULLDOWN =A00x40
>> #define OCR_TX1_PULLUP =A0 =A00x80
>> #define OCR_TX1_PUSHPULL =A00xc0
>>
>> I think implementing properties for each option is overkill.
Ugh, I see what you mean.
> Would the following more descriptive properties be OK?
>
> =A0clock-out-frequency =3D <0>, // CLKOUT pin clock off
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0=3D <4000000>; // frequency on=
CLKOUT pin
Or how about CLKOUT pin off if the property isn't present? Otherwise,
this looks okay. BTW, I'd consider prefixing this with 'nxp,' or
'sja1000,' to protect the namespace. clock-out-frequency sounds like
one of those names which could be commonly used in the future. I'd so
the same for the other chip-specific properties too.
Segher, what's your opinion on this?
> =A0bypass-input-comparator; // allows to bypass the CAN input comparator.
>
> =A0tx1-output-on-rx-irq; =A0 =A0// allows the TX1 output to be used as a
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 // dedicated RX inter=
rupt output.
>
> =A0output-control-mode =3D <0x0> // bi-phase output mode
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0<0x1> // test output mode
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0<0x2> // normal output mod=
e (default)
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0<0x3> // clock output mode
>
> =A0output-pin-config =3D <0x01> // TX0 invert
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0<0x02> // TX0 pull-down
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0<0x04> // TX0 pull-up
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0<0x06> // TX0 push-pull
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0<0x08> // TX1 invert
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0<0x10> // TX1 pull-down
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0<0x20> // TX1 pull-up
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0<0x30> // TX1 push-pull
hmmm; It is very chip specific and it is a lot of mucking around. If
you prefix the property with the manufacturer name, then perhaps the
explicit register setting is okay.
Are TX0 & TX1 protocol pins or GPIOs? If gpio, then maybe it is worth
the mucking about to then use the gpios binding to specify the pin
mode.
g.
--=20
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
^ permalink raw reply
* Re: [net-next-2.6 PATCH v2] can: SJA1000: generic OF platform bus driver
From: Wolfgang Grandegger @ 2009-05-25 6:58 UTC (permalink / raw)
To: Arnd Bergmann; +Cc: linuxppc-dev, devicetree-discuss, Linux Netdev List
In-Reply-To: <200905242327.15139.arnd@arndb.de>
Arnd Bergmann wrote:
> On Saturday 23 May 2009, Wolfgang Grandegger wrote:
>> Arnd Bergmann wrote:
>>> Minor nitpicking: dev->base_addr should be defined as an __iomem pointer
>>> so you can avoid the cast here and in the ioremap/iounmap path.
>> Here the member "base_addr" of "struct net_device" is used and it's not
>> up to me to change the type.
>
> Right, that makes sense. However, most drivers use the field to store the
> physical address, not the iomap token. Maybe there should be a new field
> in struct sja1000_priv for the virtual address, but that would be a change
> to the base driver, not just to the OF portion.
Is that common practice? If yes, I will add a member to store the
virtual address to struct sja1000_priv.
Wolfgang.
^ permalink raw reply
* Re: Initialize DBCR0 for PPC440 targets
From: Benjamin Herrenschmidt @ 2009-05-25 7:04 UTC (permalink / raw)
To: David Gibson; +Cc: srikanth krishnakar, Linuxppc-dev
In-Reply-To: <20090520060014.GL6333@yookeroo.seuss>
On Wed, 2009-05-20 at 16:00 +1000, David Gibson wrote:
> On Wed, May 20, 2009 at 11:20:46AM +0530, srikanth krishnakar wrote:
> > Hi David,
> >
> > I am not sure how the IDM behaves on few of PPC440 targets which don't
> > have boot loaders. I have a reference for your question:
> >
> > http://www.nabble.com/Question-about-DBCR0-initialization-for-440-td23049044.html
> >
> > Without this fix (given patch) I am facing problems with GDB, and
> > further target hangs while running gdbserver !
>
> That doesn't answer my question. It's not enough to say "this fixes a
> problem" you need to explain *how* it fixes the problem.
>
> And I don't see why IDM would have any effect on *software*
> breakpoints.
No but gdb can use the DABR emulation and single step would be busted
too. GDB internally heavily uses single step in places you wouldn't
expect it to :-) Like I think when breaking on main, it sometimes single
step the whole init process of the executable until it hits it. At least
I've seen it do that when I was debugging the debug support for 64-bit
Book3E.
Cheers,
Ben.
> > On Wed, May 20, 2009 at 5:23 AM, David Gibson
> > <david@gibson.dropbear.id.au> wrote:
> > > On Tue, May 19, 2009 at 06:38:53PM +0530, srikanth krishnakar wrote:
> > >> Hi,
> > >>
> > >> kernel- 2.6.29
> > >> Debug technique: KGDB
> > >>
> > >> The PowerPC kernel does not initialize the PPC440 DBCR0 register. This
> > >> prevents the use of software breakpoints in case of internal debug
> > >> mode. Looking into head_fsl_booke.S for initialization of DBCR0 is
> > >> used by boot-loaders.
> > >> It seems head_44x.S lacks this step of DBCR0 register initialization.
> > >> So fixing this with initializing the DBCR0 register as shown below :
> > >>
> > >> Subject: [PATCH] powerpc: 44x: Initialize DBCR0 for targets not having
> > >> bootloader
> > >>
> > >> The kernel does not initialize the PPC440 DBCR0 register.
> > >> This prevents (among other things) the use of software
> > >> breakpoints with GDB. The boot loaders probably do initialize
> > >> this but few targets run without a boot loader
> > >
> > > Um.. how does this prevent the use of software breakpoints with gdb?
> > > The trap instructions still work with IDM==0.
>
^ permalink raw reply
* Re: [PATCH V2 5/9] Main rewite of the mpc5200 audio DMA code
From: Juergen Beisert @ 2009-05-25 7:56 UTC (permalink / raw)
To: linuxppc-dev; +Cc: alsa-devel, broonie
In-Reply-To: <9e4733910905241310n59952fd2oaafd7f1363db324@mail.gmail.com>
Jon,
On Sonntag, 24. Mai 2009, Jon Smirl wrote:
> On Sun, May 24, 2009 at 2:55 PM, Wolfram Sang <w.sang@pengutronix.de> wrote:
> >> Rewrite the mpc5200 audio DMA code to support both I2S and AC97. Make it
> >> more robust.
> >
> > Why is it more robust?
>
> I've implemented retries for when the AC97 hardware doesn't reset on
> first try. About 10% of the time both the Efika and pcm030 AC97 codecs
> don't reset on first try and need to be poked multiple times. Failure
> is indicated by not having the link clock start ticking. Every once in
> a while even five pokes won't get the link started and I have to power
> cycle.
Do you know this (from our website)?
"The AC97 mixer needs a hardware patch to make it wake up from power down
mode. Download here the instruction how to do so."
http://www.pengutronix.de/oselas/bsp/phytec/download/phyCORE-MPC5200B-tiny/TN-015e_1.pdf
jbe
--
Pengutronix e.K. | Juergen Beisert |
Linux Solutions for Science and Industry | Phone: +49-8766-939 228 |
Vertretung Sued/Muenchen, Germany | Fax: +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de/ |
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox