* [RFC PATCH v2 2/4] cpuidle: (POWER) cpuidle driver for pSeries
From: Deepthi Dharwar @ 2011-11-17 11:28 UTC (permalink / raw)
To: linuxppc-dev, linux-pm, linux-pm; +Cc: linux-kernel
In-Reply-To: <20111117112815.9191.2322.stgit@localhost6.localdomain6>
This patch implements a backhand cpuidle driver for pSeries
based on pseries_dedicated_idle_loop and pseries_shared_idle_loop
routines. The driver is built only if CONFIG_CPU_IDLE is set. This
cpuidle driver uses global registration of idle states and
not per-cpu.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com>
Signed-off-by: Arun R Bharadwaj <arun.r.bharadwaj@gmail.com>
---
arch/powerpc/include/asm/system.h | 8 +
arch/powerpc/kernel/sysfs.c | 2
arch/powerpc/platforms/pseries/Kconfig | 9 +
arch/powerpc/platforms/pseries/Makefile | 1
arch/powerpc/platforms/pseries/processor_idle.c | 317 +++++++++++++++++++++++
arch/powerpc/platforms/pseries/pseries.h | 3
arch/powerpc/platforms/pseries/setup.c | 3
arch/powerpc/platforms/pseries/smp.c | 1
8 files changed, 341 insertions(+), 3 deletions(-)
create mode 100644 arch/powerpc/platforms/pseries/processor_idle.c
diff --git a/arch/powerpc/include/asm/system.h b/arch/powerpc/include/asm/system.h
index ff66680..f56a0a7 100644
--- a/arch/powerpc/include/asm/system.h
+++ b/arch/powerpc/include/asm/system.h
@@ -223,6 +223,14 @@ extern void *zalloc_maybe_bootmem(size_t size, gfp_t mask);
extern int powersave_nap; /* set if nap mode can be used in idle loop */
void cpu_idle_wait(void);
+#ifdef CONFIG_PSERIES_IDLE
+extern void update_smt_snooze_delay(int snooze);
+extern int pseries_notify_cpuidle_add_cpu(int cpu);
+#else
+static inline void update_smt_snooze_delay(int snooze) {}
+static inline int pseries_notify_cpuidle_add_cpu(int cpu) { return 0; }
+#endif
+
/*
* Atomic exchange
*
diff --git a/arch/powerpc/kernel/sysfs.c b/arch/powerpc/kernel/sysfs.c
index ce035c1..ebe5d78 100644
--- a/arch/powerpc/kernel/sysfs.c
+++ b/arch/powerpc/kernel/sysfs.c
@@ -18,6 +18,7 @@
#include <asm/machdep.h>
#include <asm/smp.h>
#include <asm/pmc.h>
+#include <asm/system.h>
#include "cacheinfo.h"
@@ -51,6 +52,7 @@ static ssize_t store_smt_snooze_delay(struct sys_device *dev,
return -EINVAL;
per_cpu(smt_snooze_delay, cpu->sysdev.id) = snooze;
+ update_smt_snooze_delay(snooze);
return count;
}
diff --git a/arch/powerpc/platforms/pseries/Kconfig b/arch/powerpc/platforms/pseries/Kconfig
index c81f6bb..ae7b6d4 100644
--- a/arch/powerpc/platforms/pseries/Kconfig
+++ b/arch/powerpc/platforms/pseries/Kconfig
@@ -120,3 +120,12 @@ config DTL
which are accessible through a debugfs file.
Say N if you are unsure.
+
+config PSERIES_IDLE
+ tristate "Cpuidle driver for pSeries platforms"
+ depends on CPU_IDLE
+ depends on PPC_PSERIES
+ default y
+ help
+ Select this option to enable processor idle state management
+ through cpuidle subsystem.
diff --git a/arch/powerpc/platforms/pseries/Makefile b/arch/powerpc/platforms/pseries/Makefile
index 3556e40..236db46 100644
--- a/arch/powerpc/platforms/pseries/Makefile
+++ b/arch/powerpc/platforms/pseries/Makefile
@@ -22,6 +22,7 @@ obj-$(CONFIG_PHYP_DUMP) += phyp_dump.o
obj-$(CONFIG_CMM) += cmm.o
obj-$(CONFIG_DTL) += dtl.o
obj-$(CONFIG_IO_EVENT_IRQ) += io_event_irq.o
+obj-$(CONFIG_PSERIES_IDLE) += processor_idle.o
ifeq ($(CONFIG_PPC_PSERIES),y)
obj-$(CONFIG_SUSPEND) += suspend.o
diff --git a/arch/powerpc/platforms/pseries/processor_idle.c b/arch/powerpc/platforms/pseries/processor_idle.c
new file mode 100644
index 0000000..b5addd7
--- /dev/null
+++ b/arch/powerpc/platforms/pseries/processor_idle.c
@@ -0,0 +1,317 @@
+/*
+ * processor_idle - idle state cpuidle driver.
+ * Adapted from drivers/idle/intel_idle.c and
+ * drivers/acpi/processor_idle.c
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/moduleparam.h>
+#include <linux/cpuidle.h>
+#include <linux/cpu.h>
+
+#include <asm/paca.h>
+#include <asm/reg.h>
+#include <asm/system.h>
+#include <asm/machdep.h>
+#include <asm/firmware.h>
+
+#include "plpar_wrappers.h"
+#include "pseries.h"
+
+struct cpuidle_driver pseries_idle_driver = {
+ .name = "pseries_idle",
+ .owner = THIS_MODULE,
+};
+
+#define MAX_IDLE_STATE_COUNT 2
+
+static int max_cstate = MAX_IDLE_STATE_COUNT - 1;
+static struct cpuidle_device __percpu *pseries_idle_cpuidle_devices;
+static struct cpuidle_state *cpuidle_state_table;
+
+void update_smt_snooze_delay(int snooze)
+{
+ struct cpuidle_driver *drv = cpuidle_get_driver();
+ if (drv)
+ drv->states[0].target_residency = snooze;
+}
+
+static inline void idle_loop_prolog(unsigned long *in_purr, ktime_t *kt_before)
+{
+
+ *kt_before = ktime_get_real();
+ *in_purr = mfspr(SPRN_PURR);
+ /*
+ * Indicate to the HV that we are idle. Now would be
+ * a good time to find other work to dispatch.
+ */
+ get_lppaca()->idle = 1;
+ get_lppaca()->donate_dedicated_cpu = 1;
+}
+
+static inline s64 idle_loop_epilog(unsigned long in_purr, ktime_t kt_before)
+{
+ get_lppaca()->wait_state_cycles += mfspr(SPRN_PURR) - in_purr;
+ get_lppaca()->donate_dedicated_cpu = 0;
+ get_lppaca()->idle = 0;
+
+ return ktime_to_us(ktime_sub(ktime_get_real(), kt_before));
+}
+
+
+static int snooze_loop(struct cpuidle_device *dev,
+ struct cpuidle_driver *drv,
+ int index)
+{
+ unsigned long in_purr;
+ ktime_t kt_before;
+
+ idle_loop_prolog(&in_purr, &kt_before);
+
+ local_irq_enable();
+ set_thread_flag(TIF_POLLING_NRFLAG);
+ while (!need_resched()) {
+ ppc64_runlatch_off();
+ HMT_low();
+ HMT_very_low();
+ }
+ HMT_medium();
+ clear_thread_flag(TIF_POLLING_NRFLAG);
+ smp_mb();
+ local_irq_disable();
+
+ dev->last_residency =
+ (int)idle_loop_epilog(in_purr, kt_before);
+ return index;
+}
+
+static int dedicated_cede_loop(struct cpuidle_device *dev,
+ struct cpuidle_driver *drv,
+ int index)
+{
+ unsigned long in_purr;
+ ktime_t kt_before;
+
+ idle_loop_prolog(&in_purr, &kt_before);
+
+ ppc64_runlatch_off();
+ HMT_medium();
+ cede_processor();
+
+ dev->last_residency =
+ (int)idle_loop_epilog(in_purr, kt_before);
+ return index;
+}
+
+static int shared_cede_loop(struct cpuidle_device *dev,
+ struct cpuidle_driver *drv,
+ int index)
+{
+ unsigned long in_purr;
+ ktime_t kt_before;
+
+ idle_loop_prolog(&in_purr, &kt_before);
+
+ /*
+ * Yield the processor to the hypervisor. We return if
+ * an external interrupt occurs (which are driven prior
+ * to returning here) or if a prod occurs from another
+ * processor. When returning here, external interrupts
+ * are enabled.
+ */
+ cede_processor();
+
+ dev->last_residency =
+ (int)idle_loop_epilog(in_purr, kt_before);
+ return index;
+}
+
+/*
+ * States for dedicated partition case.
+ */
+static struct cpuidle_state dedicated_states[MAX_IDLE_STATE_COUNT] = {
+ { /* Snooze */
+ .name = "snooze",
+ .desc = "snooze",
+ .flags = CPUIDLE_FLAG_TIME_VALID,
+ .exit_latency = 0,
+ .target_residency = 0,
+ .enter = &snooze_loop },
+ { /* CEDE */
+ .name = "CEDE",
+ .desc = "CEDE",
+ .flags = CPUIDLE_FLAG_TIME_VALID,
+ .exit_latency = 1,
+ .target_residency = 10,
+ .enter = &dedicated_cede_loop },
+};
+
+/*
+ * States for shared partition case.
+ */
+static struct cpuidle_state shared_states[MAX_IDLE_STATE_COUNT] = {
+ { /* Shared Cede */
+ .name = "Shared Cede",
+ .desc = "Shared Cede",
+ .flags = CPUIDLE_FLAG_TIME_VALID,
+ .exit_latency = 0,
+ .target_residency = 0,
+ .enter = &shared_cede_loop },
+};
+
+int pseries_notify_cpuidle_add_cpu(int cpu)
+{
+ struct cpuidle_device *dev =
+ per_cpu_ptr(pseries_idle_cpuidle_devices, cpu);
+ if (dev && cpuidle_get_driver()) {
+ cpuidle_disable_device(dev);
+ cpuidle_enable_device(dev);
+ }
+ return 0;
+}
+
+/*
+ * pseries_idle_cpuidle_driver_init()
+ */
+static int pseries_idle_cpuidle_driver_init(void)
+{
+ int cstate;
+ struct cpuidle_driver *drv = &pseries_idle_driver;
+
+ drv->state_count = 0;
+
+ for (cstate = 0; cstate < MAX_IDLE_STATE_COUNT; ++cstate) {
+
+ if (cstate > max_cstate)
+ break;
+
+ /* is the state not enabled? */
+ if (cpuidle_state_table[cstate].enter == NULL)
+ continue;
+
+ drv->states[drv->state_count] = /* structure copy */
+ cpuidle_state_table[cstate];
+
+ if (cpuidle_state_table == dedicated_states)
+ drv->states[drv->state_count].target_residency =
+ __get_cpu_var(smt_snooze_delay);
+
+ drv->state_count += 1;
+ }
+
+ return 0;
+}
+
+/* pseries_idle_devices_uninit(void)
+ * unregister cpuidle devices and de-allocate memory
+ */
+static void pseries_idle_devices_uninit(void)
+{
+ int i;
+ struct cpuidle_device *dev;
+
+ for_each_possible_cpu(i) {
+ dev = per_cpu_ptr(pseries_idle_cpuidle_devices, i);
+ cpuidle_unregister_device(dev);
+ }
+
+ free_percpu(pseries_idle_cpuidle_devices);
+ return;
+}
+
+/* pseries_idle_devices_init()
+ * allocate, initialize and register cpuidle device
+ */
+static int pseries_idle_devices_init(void)
+{
+ int i;
+ struct cpuidle_driver *drv = &pseries_idle_driver;
+ struct cpuidle_device *dev;
+
+ pseries_idle_cpuidle_devices = alloc_percpu(struct cpuidle_device);
+ if (pseries_idle_cpuidle_devices == NULL)
+ return -ENOMEM;
+
+ for_each_possible_cpu(i) {
+ dev = per_cpu_ptr(pseries_idle_cpuidle_devices, i);
+ dev->state_count = drv->state_count;
+ dev->cpu = i;
+ if (cpuidle_register_device(dev)) {
+ printk(KERN_DEBUG \
+ "cpuidle_register_device %d failed!\n", i);
+ return -EIO;
+ }
+ }
+
+ return 0;
+}
+
+/*
+ * pseries_idle_probe()
+ * Choose state table for shared versus dedicated partition
+ */
+static int pseries_idle_probe(void)
+{
+ if (max_cstate == 0) {
+ printk(KERN_DEBUG "pseries processor idle disabled.\n");
+ return -EPERM;
+ }
+
+ if (!firmware_has_feature(FW_FEATURE_SPLPAR)) {
+ printk(KERN_DEBUG "Using default idle\n");
+ return -ENODEV;
+ }
+
+ if (get_lppaca()->shared_proc)
+ cpuidle_state_table = shared_states;
+ else
+ cpuidle_state_table = dedicated_states;
+
+ return 0;
+}
+
+static int __init pseries_processor_idle_init(void)
+{
+ int retval;
+
+ retval = pseries_idle_probe();
+ if (retval)
+ return retval;
+
+ pseries_idle_cpuidle_driver_init();
+ retval = cpuidle_register_driver(&pseries_idle_driver);
+ if (retval) {
+ printk(KERN_DEBUG "Registration of pseries driver failed.\n");
+ return retval;
+ }
+
+ retval = pseries_idle_devices_init();
+ if (retval) {
+ pseries_idle_devices_uninit();
+ cpuidle_unregister_driver(&pseries_idle_driver);
+ return retval;
+ }
+
+ printk(KERN_DEBUG "pseries_idle_driver registered\n");
+
+ return 0;
+}
+
+static void __exit pseries_processor_idle_exit(void)
+{
+
+ pseries_idle_devices_uninit();
+ cpuidle_unregister_driver(&pseries_idle_driver);
+
+ return;
+}
+
+module_init(pseries_processor_idle_init);
+module_exit(pseries_processor_idle_exit);
+
+MODULE_AUTHOR("Deepthi Dharwar <deepthi@linux.vnet.ibm.com>");
+MODULE_DESCRIPTION("Cpuidle driver for POWER");
+MODULE_LICENSE("GPL");
diff --git a/arch/powerpc/platforms/pseries/pseries.h b/arch/powerpc/platforms/pseries/pseries.h
index 24c7162..9a3dda0 100644
--- a/arch/powerpc/platforms/pseries/pseries.h
+++ b/arch/powerpc/platforms/pseries/pseries.h
@@ -57,4 +57,7 @@ extern struct device_node *dlpar_configure_connector(u32);
extern int dlpar_attach_node(struct device_node *);
extern int dlpar_detach_node(struct device_node *);
+/* Snooze Delay, pseries_idle */
+DECLARE_PER_CPU(long, smt_snooze_delay);
+
#endif /* _PSERIES_PSERIES_H */
diff --git a/arch/powerpc/platforms/pseries/setup.c b/arch/powerpc/platforms/pseries/setup.c
index c3408ca..9c6716a 100644
--- a/arch/powerpc/platforms/pseries/setup.c
+++ b/arch/powerpc/platforms/pseries/setup.c
@@ -586,9 +586,6 @@ static int __init pSeries_probe(void)
return 1;
}
-
-DECLARE_PER_CPU(long, smt_snooze_delay);
-
static void pseries_dedicated_idle_sleep(void)
{
unsigned int cpu = smp_processor_id();
diff --git a/arch/powerpc/platforms/pseries/smp.c b/arch/powerpc/platforms/pseries/smp.c
index 26e93fd..bbc3c42 100644
--- a/arch/powerpc/platforms/pseries/smp.c
+++ b/arch/powerpc/platforms/pseries/smp.c
@@ -148,6 +148,7 @@ static void __devinit smp_xics_setup_cpu(int cpu)
set_cpu_current_state(cpu, CPU_STATE_ONLINE);
set_default_offline_state(cpu);
#endif
+ pseries_notify_cpuidle_add_cpu(cpu);
}
static int __devinit smp_pSeries_kick_cpu(int nr)
^ permalink raw reply related
* [RFC PATCH v2 1/4] cpuidle: (powerpc) Add cpu_idle_wait() to allow switching of idle routines
From: Deepthi Dharwar @ 2011-11-17 11:28 UTC (permalink / raw)
To: linuxppc-dev, linux-pm, linux-pm; +Cc: linux-kernel
In-Reply-To: <20111117112815.9191.2322.stgit@localhost6.localdomain6>
This patch provides cpu_idle_wait() routine for the powerpc
platform which is required by the cpuidle subsystem. This
routine is requied to change the idle handler on SMP systems.
The equivalent routine for x86 is in arch/x86/kernel/process.c
but the powerpc implementation is different.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com>
Signed-off-by: Arun R Bharadwaj <arun.r.bharadwaj@gmail.com>
---
arch/powerpc/Kconfig | 4 ++++
arch/powerpc/include/asm/processor.h | 2 ++
arch/powerpc/include/asm/system.h | 1 +
arch/powerpc/kernel/idle.c | 26 ++++++++++++++++++++++++++
4 files changed, 33 insertions(+), 0 deletions(-)
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index b177caa..87f8604 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -87,6 +87,10 @@ config ARCH_HAS_ILOG2_U64
bool
default y if 64BIT
+config ARCH_HAS_CPU_IDLE_WAIT
+ bool
+ default y
+
config GENERIC_HWEIGHT
bool
default y
diff --git a/arch/powerpc/include/asm/processor.h b/arch/powerpc/include/asm/processor.h
index eb11a44..811b7e7 100644
--- a/arch/powerpc/include/asm/processor.h
+++ b/arch/powerpc/include/asm/processor.h
@@ -382,6 +382,8 @@ static inline unsigned long get_clean_sp(struct pt_regs *regs, int is_32)
}
#endif
+enum idle_boot_override {IDLE_NO_OVERRIDE = 0, IDLE_POWERSAVE_OFF};
+
#endif /* __KERNEL__ */
#endif /* __ASSEMBLY__ */
#endif /* _ASM_POWERPC_PROCESSOR_H */
diff --git a/arch/powerpc/include/asm/system.h b/arch/powerpc/include/asm/system.h
index e30a13d..ff66680 100644
--- a/arch/powerpc/include/asm/system.h
+++ b/arch/powerpc/include/asm/system.h
@@ -221,6 +221,7 @@ extern unsigned long klimit;
extern void *zalloc_maybe_bootmem(size_t size, gfp_t mask);
extern int powersave_nap; /* set if nap mode can be used in idle loop */
+void cpu_idle_wait(void);
/*
* Atomic exchange
diff --git a/arch/powerpc/kernel/idle.c b/arch/powerpc/kernel/idle.c
index 39a2baa..b478c72 100644
--- a/arch/powerpc/kernel/idle.c
+++ b/arch/powerpc/kernel/idle.c
@@ -39,9 +39,13 @@
#define cpu_should_die() 0
#endif
+unsigned long boot_option_idle_override = IDLE_NO_OVERRIDE;
+EXPORT_SYMBOL(boot_option_idle_override);
+
static int __init powersave_off(char *arg)
{
ppc_md.power_save = NULL;
+ boot_option_idle_override = IDLE_POWERSAVE_OFF;
return 0;
}
__setup("powersave=off", powersave_off);
@@ -102,6 +106,28 @@ void cpu_idle(void)
}
}
+
+/*
+ * cpu_idle_wait - Used to ensure that all the CPUs come out of the old
+ * idle loop and start using the new idle loop.
+ * Required while changing idle handler on SMP systems.
+ * Caller must have changed idle handler to the new value before the call.
+ */
+void cpu_idle_wait(void)
+{
+ int cpu;
+ smp_mb();
+
+ /* kick all the CPUs so that they exit out of old idle routine */
+ get_online_cpus();
+ for_each_online_cpu(cpu) {
+ if (cpu != smp_processor_id())
+ smp_send_reschedule(cpu);
+ }
+ put_online_cpus();
+}
+EXPORT_SYMBOL_GPL(cpu_idle_wait);
+
int powersave_nap;
#ifdef CONFIG_SYSCTL
^ permalink raw reply related
* RE: [PATCH v2 2/7] powerpc/85xx: add HOTPLUG_CPU support
From: Li Yang-R58472 @ 2011-11-17 11:16 UTC (permalink / raw)
To: Wood Scott-B07421, Zhao Chenhui-B35336; +Cc: linuxppc-dev@lists.ozlabs.org
In-Reply-To: <4EC408C1.1040400@freescale.com>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^ permalink raw reply
* [PATCH v2 7/7] gianfar: add support for wake-on-packet
From: Zhao Chenhui @ 2011-11-17 11:10 UTC (permalink / raw)
To: linuxppc-dev; +Cc: netdev, afleming
On certain chip like MPC8536 and P1022, system can be waked up from
sleep by user-defined packet and Magic Patcket.(The eTSEC cannot
supports both types of wake-up event simultaneously.) This patch
implements wake-up on user-defined patcket including ARP request
packet and unicast patcket to this station.
When entering suspend state, the gianfar driver sets receive queue
filer table to filter all of packets except ARP request packet and
unicast patcket to this station. The driver temporarily uses the last
receive queue to receive the user defined packet.
In suspend state, the receive part of eTSEC keeps working. When
receiving a user defined packet, it generates an interrupt to
wake up the system.
The rule of the filer table is as below.
if (arp request to local ip address)
accept it to the last queue
elif (unicast packet to local mac address)
accept it to the last queue
else
reject it
endif
Note: The local ip/mac address is the ethernet primary IP/MAC address of
the station. Do not support multiple IP/MAC addresses.
Here is an example of enabling and testing wake up on user defined packet.
ifconfig eth0 10.193.20.169
ethtool -s eth0 wol a
echo standby > /sys/power/state or echo mem > /sys/power/state
Ping from PC host to wake up the station:
ping 10.193.20.169
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
---
Changes for v2:
- rework gfar_get_ip(), gfar_config_filer_table(), gfar_suspend() and gfar_resume()
- add support unicast wakeup
- add supported in struct gfar_private
.../devicetree/bindings/net/fsl-tsec-phy.txt | 3 +
drivers/net/ethernet/freescale/gianfar.c | 362 +++++++++++++++++---
drivers/net/ethernet/freescale/gianfar.h | 33 ++-
drivers/net/ethernet/freescale/gianfar_ethtool.c | 52 ++-
4 files changed, 372 insertions(+), 78 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
index 2c6be03..543e36c 100644
--- a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
+++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
@@ -56,6 +56,9 @@ Properties:
hardware.
- fsl,magic-packet : If present, indicates that the hardware supports
waking up via magic packet.
+ - fsl,wake-on-filer : If present, indicates that the hardware supports
+ waking up via arp request to local ip address or unicast packet to
+ local mac address.
- bd-stash : If present, indicates that the hardware supports stashing
buffer descriptors in the L2.
- rx-stash-len : Denotes the number of bytes of a received buffer to stash
diff --git a/drivers/net/ethernet/freescale/gianfar.c b/drivers/net/ethernet/freescale/gianfar.c
index 83199fd..991bd47 100644
--- a/drivers/net/ethernet/freescale/gianfar.c
+++ b/drivers/net/ethernet/freescale/gianfar.c
@@ -85,6 +85,8 @@
#include <linux/tcp.h>
#include <linux/udp.h>
#include <linux/in.h>
+#include <linux/inetdevice.h>
+#include <sysdev/fsl_soc.h>
#include <linux/net_tstamp.h>
#include <asm/io.h>
@@ -147,6 +149,17 @@ static void gfar_clear_exact_match(struct net_device *dev);
static void gfar_set_mac_for_addr(struct net_device *dev, int num,
const u8 *addr);
static int gfar_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
+static void gfar_schedule_cleanup(struct gfar_priv_grp *gfargrp);
+
+#ifdef CONFIG_PM
+static void gfar_halt_rx(struct net_device *dev);
+static void gfar_rx_start(struct net_device *dev);
+static void gfar_enable_filer(struct net_device *dev);
+static void gfar_disable_filer(struct net_device *dev);
+static void gfar_config_filer_table(struct net_device *dev);
+static void gfar_restore_filer_table(struct net_device *dev);
+static int gfar_get_ip(struct net_device *dev);
+#endif
MODULE_AUTHOR("Freescale Semiconductor, Inc");
MODULE_DESCRIPTION("Gianfar Ethernet Driver");
@@ -751,7 +764,6 @@ static int gfar_of_init(struct platform_device *ofdev, struct net_device **pdev)
FSL_GIANFAR_DEV_HAS_PADDING |
FSL_GIANFAR_DEV_HAS_CSUM |
FSL_GIANFAR_DEV_HAS_VLAN |
- FSL_GIANFAR_DEV_HAS_MAGIC_PACKET |
FSL_GIANFAR_DEV_HAS_EXTENDED_HASH |
FSL_GIANFAR_DEV_HAS_TIMER;
@@ -763,8 +775,19 @@ static int gfar_of_init(struct platform_device *ofdev, struct net_device **pdev)
else
priv->interface = PHY_INTERFACE_MODE_MII;
- if (of_get_property(np, "fsl,magic-packet", NULL))
+ /* Init Wake-on-LAN */
+ priv->wol_opts = 0;
+ priv->wol_supported = 0;
+ if (of_get_property(np, "fsl,magic-packet", NULL)) {
priv->device_flags |= FSL_GIANFAR_DEV_HAS_MAGIC_PACKET;
+ priv->wol_supported |= GIANFAR_WOL_MAGIC;
+ }
+
+ if (of_get_property(np, "fsl,wake-on-filer", NULL)) {
+ priv->device_flags |= FSL_GIANFAR_DEV_HAS_WAKE_ON_FILER;
+ priv->wol_supported |= GIANFAR_WOL_ARP;
+ priv->wol_supported |= GIANFAR_WOL_UCAST;
+ }
priv->phy_node = of_parse_phandle(np, "phy-handle", 0);
@@ -1168,8 +1191,10 @@ static int gfar_probe(struct platform_device *ofdev)
goto register_fail;
}
- device_init_wakeup(&dev->dev,
- priv->device_flags & FSL_GIANFAR_DEV_HAS_MAGIC_PACKET);
+ if (priv->wol_supported) {
+ device_set_wakeup_capable(&ofdev->dev, true);
+ device_set_wakeup_enable(&ofdev->dev, false);
+ }
/* fill out IRQ number and name fields */
len_devname = strlen(dev->name);
@@ -1260,6 +1285,143 @@ static int gfar_remove(struct platform_device *ofdev)
}
#ifdef CONFIG_PM
+static void gfar_enable_filer(struct net_device *dev)
+{
+ struct gfar_private *priv = netdev_priv(dev);
+ struct gfar __iomem *regs = priv->gfargrp[0].regs;
+ u32 temp;
+
+ lock_rx_qs(priv);
+
+ temp = gfar_read(®s->rctrl);
+ temp &= ~(RCTRL_FSQEN | RCTRL_PRSDEP_MASK);
+ temp |= RCTRL_FILREN | RCTRL_PRSDEP_L2L3;
+ gfar_write(®s->rctrl, temp);
+
+ unlock_rx_qs(priv);
+}
+
+static void gfar_disable_filer(struct net_device *dev)
+{
+ struct gfar_private *priv = netdev_priv(dev);
+ struct gfar __iomem *regs = priv->gfargrp[0].regs;
+ u32 temp;
+
+ lock_rx_qs(priv);
+
+ temp = gfar_read(®s->rctrl);
+ temp &= ~RCTRL_FILREN;
+ gfar_write(®s->rctrl, temp);
+
+ unlock_rx_qs(priv);
+}
+
+static int gfar_get_ip(struct net_device *dev)
+{
+ struct gfar_private *priv = netdev_priv(dev);
+ struct in_device *in_dev;
+ int ret = -ENOENT;
+
+ in_dev = in_dev_get(dev);
+ if (!in_dev)
+ return ret;
+
+ /* Get the primary IP address */
+ for_primary_ifa(in_dev) {
+ priv->ip_addr = ifa->ifa_address;
+ ret = 0;
+ break;
+ } endfor_ifa(in_dev);
+
+ in_dev_put(in_dev);
+ return ret;
+}
+
+static void gfar_restore_filer_table(struct net_device *dev)
+{
+ struct gfar_private *priv = netdev_priv(dev);
+ u32 rqfcr, rqfpr;
+ int i;
+
+ lock_rx_qs(priv);
+
+ for (i = 0; i <= MAX_FILER_IDX; i++) {
+ rqfcr = priv->ftp_rqfcr[i];
+ rqfpr = priv->ftp_rqfpr[i];
+ gfar_write_filer(priv, i, rqfcr, rqfpr);
+ }
+
+ unlock_rx_qs(priv);
+}
+
+static void gfar_config_filer_table(struct net_device *dev)
+{
+ struct gfar_private *priv = netdev_priv(dev);
+ u32 dest_mac_addr;
+ u32 rqfcr, rqfpr;
+ u8 rqfcr_queue = priv->num_rx_queues - 1;
+ unsigned int index;
+
+ if (gfar_get_ip(dev)) {
+ netif_err(priv, wol, dev, "WOL: get the ip address error\n");
+ return;
+ }
+
+ lock_rx_qs(priv);
+
+ /* init filer table */
+ rqfcr = RQFCR_RJE | RQFCR_CMP_MATCH;
+ rqfpr = 0x0;
+ for (index = 0; index <= MAX_FILER_IDX; index++)
+ gfar_write_filer(priv, index, rqfcr, rqfpr);
+
+ index = 0;
+ if (priv->wol_opts & GIANFAR_WOL_ARP) {
+ /* ARP request filer, filling the packet to the last queue */
+ rqfcr = (rqfcr_queue << 10) | RQFCR_AND |
+ RQFCR_CMP_EXACT | RQFCR_PID_MASK;
+ rqfpr = RQFPR_ARQ;
+ gfar_write_filer(priv, index++, rqfcr, rqfpr);
+
+ rqfcr = (rqfcr_queue << 10) | RQFCR_AND |
+ RQFCR_CMP_EXACT | RQFCR_PID_PARSE;
+ rqfpr = RQFPR_ARQ;
+ gfar_write_filer(priv, index++, rqfcr, rqfpr);
+
+ /*
+ * DEST_IP address in ARP packet,
+ * filling it to the last queue.
+ */
+ rqfcr = (rqfcr_queue << 10) | RQFCR_AND |
+ RQFCR_CMP_EXACT | RQFCR_PID_MASK;
+ rqfpr = FPR_FILER_MASK;
+ gfar_write_filer(priv, index++, rqfcr, rqfpr);
+
+ rqfcr = (rqfcr_queue << 10) | RQFCR_GPI |
+ RQFCR_CMP_EXACT | RQFCR_PID_DIA;
+ rqfpr = priv->ip_addr;
+ gfar_write_filer(priv, index++, rqfcr, rqfpr);
+ }
+
+ if (priv->wol_opts & GIANFAR_WOL_UCAST) {
+ /* Unicast packet, filling it to the last queue */
+ dest_mac_addr = (dev->dev_addr[0] << 16) |
+ (dev->dev_addr[1] << 8) | dev->dev_addr[2];
+ rqfcr = (rqfcr_queue << 10) | RQFCR_AND |
+ RQFCR_CMP_EXACT | RQFCR_PID_DAH;
+ rqfpr = dest_mac_addr;
+ gfar_write_filer(priv, index++, rqfcr, rqfpr);
+
+ dest_mac_addr = (dev->dev_addr[3] << 16) |
+ (dev->dev_addr[4] << 8) | dev->dev_addr[5];
+ rqfcr = (rqfcr_queue << 10) | RQFCR_GPI |
+ RQFCR_CMP_EXACT | RQFCR_PID_DAL;
+ rqfpr = dest_mac_addr;
+ gfar_write_filer(priv, index++, rqfcr, rqfpr);
+ }
+
+ unlock_rx_qs(priv);
+}
static int gfar_suspend(struct device *dev)
{
@@ -1269,48 +1431,43 @@ static int gfar_suspend(struct device *dev)
unsigned long flags;
u32 tempval;
- int magic_packet = priv->wol_en &&
- (priv->device_flags & FSL_GIANFAR_DEV_HAS_MAGIC_PACKET);
-
netif_device_detach(ndev);
- if (netif_running(ndev)) {
-
- local_irq_save(flags);
- lock_tx_qs(priv);
- lock_rx_qs(priv);
-
- gfar_halt_nodisable(ndev);
-
- /* Disable Tx, and Rx if wake-on-LAN is disabled. */
- tempval = gfar_read(®s->maccfg1);
-
- tempval &= ~MACCFG1_TX_EN;
+ if (!netif_running(ndev))
+ return 0;
- if (!magic_packet)
- tempval &= ~MACCFG1_RX_EN;
+ local_irq_save(flags);
+ lock_tx_qs(priv);
+ lock_rx_qs(priv);
- gfar_write(®s->maccfg1, tempval);
+ gfar_halt(ndev);
- unlock_rx_qs(priv);
- unlock_tx_qs(priv);
- local_irq_restore(flags);
+ unlock_rx_qs(priv);
+ unlock_tx_qs(priv);
+ local_irq_restore(flags);
- disable_napi(priv);
+ disable_napi(priv);
- if (magic_packet) {
- /* Enable interrupt on Magic Packet */
- gfar_write(®s->imask, IMASK_MAG);
+ if (!priv->wol_opts && priv->phydev) {
+ phy_stop(priv->phydev);
+ return 0;
+ }
- /* Enable Magic Packet mode */
- tempval = gfar_read(®s->maccfg2);
- tempval |= MACCFG2_MPEN;
- gfar_write(®s->maccfg2, tempval);
- } else {
- phy_stop(priv->phydev);
- }
+ mpc85xx_pmc_set_wake(priv->ofdev, 1);
+ if (priv->wol_opts & GIANFAR_WOL_MAGIC) {
+ /* Enable Magic Packet mode */
+ tempval = gfar_read(®s->maccfg2);
+ tempval |= MACCFG2_MPEN;
+ gfar_write(®s->maccfg2, tempval);
}
+ if (priv->wol_opts & (GIANFAR_WOL_ARP | GIANFAR_WOL_UCAST)) {
+ mpc85xx_pmc_set_lossless_ethernet(1);
+ gfar_disable_filer(ndev);
+ gfar_config_filer_table(ndev);
+ gfar_enable_filer(ndev);
+ }
+ gfar_rx_start(ndev);
return 0;
}
@@ -1320,39 +1477,49 @@ static int gfar_resume(struct device *dev)
struct net_device *ndev = priv->ndev;
struct gfar __iomem *regs = priv->gfargrp[0].regs;
unsigned long flags;
- u32 tempval;
- int magic_packet = priv->wol_en &&
- (priv->device_flags & FSL_GIANFAR_DEV_HAS_MAGIC_PACKET);
+ u32 tempval, i;
if (!netif_running(ndev)) {
netif_device_attach(ndev);
return 0;
}
- if (!magic_packet && priv->phydev)
+ if (!priv->wol_opts && priv->phydev) {
phy_start(priv->phydev);
+ goto out;
+ }
+
+ mpc85xx_pmc_set_wake(priv->ofdev, 0);
- /* Disable Magic Packet mode, in case something
- * else woke us up.
- */
local_irq_save(flags);
- lock_tx_qs(priv);
lock_rx_qs(priv);
-
- tempval = gfar_read(®s->maccfg2);
- tempval &= ~MACCFG2_MPEN;
- gfar_write(®s->maccfg2, tempval);
-
- gfar_start(ndev);
-
+ gfar_halt_rx(ndev);
unlock_rx_qs(priv);
- unlock_tx_qs(priv);
local_irq_restore(flags);
- netif_device_attach(ndev);
+ if (priv->wol_opts & (GIANFAR_WOL_ARP | GIANFAR_WOL_UCAST)) {
+ mpc85xx_pmc_set_lossless_ethernet(0);
+ gfar_disable_filer(ndev);
+ gfar_restore_filer_table(ndev);
+ }
+
+ if (priv->wol_opts & GIANFAR_WOL_MAGIC) {
+ /* Disable Magic Packet mode */
+ tempval = gfar_read(®s->maccfg2);
+ tempval &= ~MACCFG2_MPEN;
+ gfar_write(®s->maccfg2, tempval);
+ }
+out:
+ gfar_start(ndev);
+ netif_device_attach(ndev);
enable_napi(priv);
+ if (priv->wol_opts & (GIANFAR_WOL_ARP | GIANFAR_WOL_UCAST)) {
+ /* send requests to process the received packets */
+ for (i = 0; i < priv->num_grps; i++)
+ gfar_schedule_cleanup(&priv->gfargrp[i]);
+ }
return 0;
}
@@ -1602,6 +1769,48 @@ static int __gfar_is_rx_idle(struct gfar_private *priv)
return 0;
}
+#ifdef CONFIG_PM
+/* Halt the receive queues */
+static void gfar_halt_rx(struct net_device *dev)
+{
+ struct gfar_private *priv = netdev_priv(dev);
+ struct gfar __iomem *regs = priv->gfargrp[0].regs;
+ u32 tempval;
+ int i = 0;
+
+ for (i = 0; i < priv->num_grps; i++) {
+ regs = priv->gfargrp[i].regs;
+ /* Mask all interrupts */
+ gfar_write(®s->imask, IMASK_INIT_CLEAR);
+
+ /* Clear all interrupts */
+ gfar_write(®s->ievent, IEVENT_INIT_CLEAR);
+ }
+
+ regs = priv->gfargrp[0].regs;
+ /* Stop the DMA, and wait for it to stop */
+ tempval = gfar_read(®s->dmactrl);
+ if ((tempval & DMACTRL_GRS) != DMACTRL_GRS) {
+ int ret;
+
+ tempval |= DMACTRL_GRS;
+ gfar_write(®s->dmactrl, tempval);
+
+ do {
+ ret = spin_event_timeout(((gfar_read(®s->ievent) &
+ IEVENT_GRSC) == IEVENT_GRSC), 1000000, 0);
+ if (!ret && !(gfar_read(®s->ievent) & IEVENT_GRSC))
+ ret = __gfar_is_rx_idle(priv);
+ } while (!ret);
+ }
+
+ /* Disable Rx in MACCFG1 */
+ tempval = gfar_read(®s->maccfg1);
+ tempval &= ~MACCFG1_RX_EN;
+ gfar_write(®s->maccfg1, tempval);
+}
+#endif
+
/* Halt the receive and transmit queues */
static void gfar_halt_nodisable(struct net_device *dev)
{
@@ -1808,6 +2017,40 @@ void gfar_start(struct net_device *dev)
dev->trans_start = jiffies; /* prevent tx timeout */
}
+#ifdef CONFIG_PM
+void gfar_rx_start(struct net_device *dev)
+{
+ struct gfar_private *priv = netdev_priv(dev);
+ struct gfar __iomem *regs = priv->gfargrp[0].regs;
+ u32 tempval;
+ int i = 0;
+
+ /* Enable Rx in MACCFG1 */
+ tempval = gfar_read(®s->maccfg1);
+ tempval |= MACCFG1_RX_EN;
+ gfar_write(®s->maccfg1, tempval);
+
+ /* Initialize DMACTRL to have WWR and WOP */
+ tempval = gfar_read(®s->dmactrl);
+ tempval |= DMACTRL_INIT_SETTINGS;
+ gfar_write(®s->dmactrl, tempval);
+
+ /* Make sure we aren't stopped */
+ tempval = gfar_read(®s->dmactrl);
+ tempval &= ~DMACTRL_GRS;
+ gfar_write(®s->dmactrl, tempval);
+
+ for (i = 0; i < priv->num_grps; i++) {
+ regs = priv->gfargrp[i].regs;
+ /* Clear RHLT, so that the DMA starts polling now */
+ gfar_write(®s->rstat, priv->gfargrp[i].rstat);
+
+ /* Unmask the interrupts we look for */
+ gfar_write(®s->imask, IMASK_DEFAULT);
+ }
+}
+#endif
+
void gfar_configure_coalescing(struct gfar_private *priv,
unsigned long tx_mask, unsigned long rx_mask)
{
@@ -1970,7 +2213,7 @@ static int gfar_enet_open(struct net_device *dev)
netif_tx_start_all_queues(dev);
- device_set_wakeup_enable(&dev->dev, priv->wol_en);
+ device_set_wakeup_enable(&priv->ofdev->dev, priv->wol_opts);
return err;
}
@@ -2657,6 +2900,17 @@ static inline void count_errors(unsigned short status, struct net_device *dev)
irqreturn_t gfar_receive(int irq, void *grp_id)
{
+ struct gfar_priv_grp *gfargrp = grp_id;
+ struct gfar __iomem *regs = gfargrp->regs;
+ u32 ievent;
+
+ ievent = gfar_read(®s->ievent);
+
+ if ((ievent & IEVENT_FGPI) == IEVENT_FGPI) {
+ gfar_write(®s->ievent, ievent & IEVENT_RX_MASK);
+ return IRQ_HANDLED;
+ }
+
gfar_schedule_cleanup((struct gfar_priv_grp *)grp_id);
return IRQ_HANDLED;
}
diff --git a/drivers/net/ethernet/freescale/gianfar.h b/drivers/net/ethernet/freescale/gianfar.h
index 9aa4377..1abebc4 100644
--- a/drivers/net/ethernet/freescale/gianfar.h
+++ b/drivers/net/ethernet/freescale/gianfar.h
@@ -232,6 +232,13 @@ extern const char gfar_driver_version[];
#define RQUEUE_EN7 0x00000001
#define RQUEUE_EN_ALL 0x000000FF
+/* Wake-On-Lan options */
+#define GIANFAR_WOL_UCAST 0x00000001 /* Unicast wakeup */
+#define GIANFAR_WOL_MCAST 0x00000002 /* Multicast wakeup */
+#define GIANFAR_WOL_BCAST 0x00000004 /* Broadcase wakeup */
+#define GIANFAR_WOL_ARP 0x00000008 /* ARP request wakeup */
+#define GIANFAR_WOL_MAGIC 0x00000010 /* Magic packet wakeup */
+
/* Init to do tx snooping for buffers and descriptors */
#define DMACTRL_INIT_SETTINGS 0x000000c3
#define DMACTRL_GRS 0x00000010
@@ -277,11 +284,15 @@ extern const char gfar_driver_version[];
#define RCTRL_PAL_MASK 0x001f0000
#define RCTRL_VLEX 0x00002000
#define RCTRL_FILREN 0x00001000
+#define RCTRL_FSQEN 0x00000800
#define RCTRL_GHTX 0x00000400
#define RCTRL_IPCSEN 0x00000200
#define RCTRL_TUCSEN 0x00000100
#define RCTRL_PRSDEP_MASK 0x000000c0
#define RCTRL_PRSDEP_INIT 0x000000c0
+#define RCTRL_PRSDEP_L2 0x00000040
+#define RCTRL_PRSDEP_L2L3 0x00000080
+#define RCTRL_PRSDEP_L2L3L4 0x000000c0
#define RCTRL_PRSFM 0x00000020
#define RCTRL_PROM 0x00000008
#define RCTRL_EMEN 0x00000002
@@ -327,18 +338,20 @@ extern const char gfar_driver_version[];
#define IEVENT_MAG 0x00000800
#define IEVENT_GRSC 0x00000100
#define IEVENT_RXF0 0x00000080
+#define IEVENT_FGPI 0x00000010
#define IEVENT_FIR 0x00000008
#define IEVENT_FIQ 0x00000004
#define IEVENT_DPE 0x00000002
#define IEVENT_PERR 0x00000001
-#define IEVENT_RX_MASK (IEVENT_RXB0 | IEVENT_RXF0 | IEVENT_BSY)
+#define IEVENT_RX_MASK (IEVENT_RXB0 | IEVENT_RXF0 | \
+ IEVENT_FGPI | IEVENT_BSY)
#define IEVENT_TX_MASK (IEVENT_TXB | IEVENT_TXF)
#define IEVENT_RTX_MASK (IEVENT_RX_MASK | IEVENT_TX_MASK)
#define IEVENT_ERR_MASK \
-(IEVENT_RXC | IEVENT_BSY | IEVENT_EBERR | IEVENT_MSRO | \
- IEVENT_BABT | IEVENT_TXC | IEVENT_TXE | IEVENT_LC \
- | IEVENT_CRL | IEVENT_XFUN | IEVENT_DPE | IEVENT_PERR \
- | IEVENT_MAG | IEVENT_BABR)
+ (IEVENT_RXC | IEVENT_BSY | IEVENT_EBERR | IEVENT_MSRO | \
+ IEVENT_BABT | IEVENT_TXC | IEVENT_TXE | IEVENT_LC | \
+ IEVENT_CRL | IEVENT_XFUN | IEVENT_FIR | IEVENT_FIQ | \
+ IEVENT_DPE | IEVENT_PERR | IEVENT_MAG | IEVENT_BABR)
#define IMASK_INIT_CLEAR 0x00000000
#define IMASK_BABR 0x80000000
@@ -359,14 +372,15 @@ extern const char gfar_driver_version[];
#define IMASK_MAG 0x00000800
#define IMASK_GRSC 0x00000100
#define IMASK_RXFEN0 0x00000080
+#define IMASK_FGPI 0x00000010
#define IMASK_FIR 0x00000008
#define IMASK_FIQ 0x00000004
#define IMASK_DPE 0x00000002
#define IMASK_PERR 0x00000001
#define IMASK_DEFAULT (IMASK_TXEEN | IMASK_TXFEN | IMASK_TXBEN | \
IMASK_RXFEN0 | IMASK_BSY | IMASK_EBERR | IMASK_BABR | \
- IMASK_XFUN | IMASK_RXC | IMASK_BABT | IMASK_DPE \
- | IMASK_PERR)
+ IMASK_XFUN | IMASK_RXC | IMASK_BABT | IMASK_FGPI | \
+ IMASK_FIR | IMASK_FIQ | IMASK_DPE | IMASK_PERR | IMASK_MAG)
#define IMASK_RTX_DISABLED ((~(IMASK_RXFEN0 | IMASK_TXFEN | IMASK_BSY)) \
& IMASK_DEFAULT)
@@ -883,6 +897,7 @@ struct gfar {
#define FSL_GIANFAR_DEV_HAS_BD_STASHING 0x00000200
#define FSL_GIANFAR_DEV_HAS_BUF_STASHING 0x00000400
#define FSL_GIANFAR_DEV_HAS_TIMER 0x00000800
+#define FSL_GIANFAR_DEV_HAS_WAKE_ON_FILER 0x00001000
#if (MAXGROUPS == 2)
#define DEFAULT_MAPPING 0xAA
@@ -1115,6 +1130,10 @@ struct gfar_private {
struct work_struct reset_task;
+ u32 ip_addr;
+ u32 wol_opts;
+ u32 wol_supported;
+
/* Network Statistics */
struct gfar_extra_stats extra_stats;
diff --git a/drivers/net/ethernet/freescale/gianfar_ethtool.c b/drivers/net/ethernet/freescale/gianfar_ethtool.c
index 212736b..296e762 100644
--- a/drivers/net/ethernet/freescale/gianfar_ethtool.c
+++ b/drivers/net/ethernet/freescale/gianfar_ethtool.c
@@ -29,6 +29,7 @@
#include <linux/skbuff.h>
#include <linux/spinlock.h>
#include <linux/mm.h>
+#include <linux/platform_device.h>
#include <asm/io.h>
#include <asm/irq.h>
@@ -577,32 +578,49 @@ static void gfar_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
{
struct gfar_private *priv = netdev_priv(dev);
- if (priv->device_flags & FSL_GIANFAR_DEV_HAS_MAGIC_PACKET) {
- wol->supported = WAKE_MAGIC;
- wol->wolopts = priv->wol_en ? WAKE_MAGIC : 0;
- } else {
- wol->supported = wol->wolopts = 0;
- }
+ wol->supported = 0;
+ wol->wolopts = 0;
+
+ if (!priv->wol_supported || !device_can_wakeup(&priv->ofdev->dev))
+ return;
+
+ if (priv->wol_supported & GIANFAR_WOL_MAGIC)
+ wol->supported |= WAKE_MAGIC;
+
+ if (priv->wol_supported & GIANFAR_WOL_ARP)
+ wol->supported |= WAKE_ARP;
+
+ if (priv->wol_supported & GIANFAR_WOL_UCAST)
+ wol->supported |= WAKE_UCAST;
+
+ if (priv->wol_opts & GIANFAR_WOL_MAGIC)
+ wol->wolopts |= WAKE_MAGIC;
+
+ if (priv->wol_opts & GIANFAR_WOL_ARP)
+ wol->wolopts |= WAKE_ARP;
+
+ if (priv->wol_opts & GIANFAR_WOL_UCAST)
+ wol->wolopts |= WAKE_UCAST;
}
static int gfar_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
{
struct gfar_private *priv = netdev_priv(dev);
- unsigned long flags;
- if (!(priv->device_flags & FSL_GIANFAR_DEV_HAS_MAGIC_PACKET) &&
- wol->wolopts != 0)
- return -EINVAL;
-
- if (wol->wolopts & ~WAKE_MAGIC)
- return -EINVAL;
+ if (!priv->wol_supported || !device_can_wakeup(&priv->ofdev->dev) ||
+ (wol->wolopts & ~(WAKE_MAGIC | WAKE_ARP | WAKE_UCAST)))
+ return -EOPNOTSUPP;
- device_set_wakeup_enable(&dev->dev, wol->wolopts & WAKE_MAGIC);
+ priv->wol_opts = 0;
- spin_lock_irqsave(&priv->bflock, flags);
- priv->wol_en = !!device_may_wakeup(&dev->dev);
- spin_unlock_irqrestore(&priv->bflock, flags);
+ if (wol->wolopts & WAKE_MAGIC)
+ priv->wol_opts |= GIANFAR_WOL_MAGIC;
+ if (wol->wolopts & WAKE_ARP)
+ priv->wol_opts |= GIANFAR_WOL_ARP;
+ if (wol->wolopts & WAKE_UCAST)
+ priv->wol_opts |= GIANFAR_WOL_UCAST;
+ device_set_wakeup_enable(&priv->ofdev->dev, (u32)priv->wol_opts);
return 0;
}
#endif
--
1.6.4.1
^ permalink raw reply related
* [PATCH 29/29] powerpc/85xx: Rework P5020DS device tree
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-28-git-send-email-galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p5020-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/fsl/p5020si-post.dtsi | 335 +++++++++++++
arch/powerpc/boot/dts/fsl/p5020si-pre.dtsi | 96 ++++
arch/powerpc/boot/dts/p5020ds.dts | 13 +-
arch/powerpc/boot/dts/p5020si.dtsi | 716 ---------------------------
4 files changed, 441 insertions(+), 719 deletions(-)
create mode 100644 arch/powerpc/boot/dts/fsl/p5020si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/p5020si-pre.dtsi
delete mode 100644 arch/powerpc/boot/dts/p5020si.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/p5020si-post.dtsi b/arch/powerpc/boot/dts/fsl/p5020si-post.dtsi
new file mode 100644
index 0000000..7135c67
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p5020si-post.dtsi
@@ -0,0 +1,335 @@
+/*
+ * P5020/5010 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ compatible = "fsl,p5020-elbc", "fsl,elbc", "simple-bus";
+ interrupts = <25 2 0 0>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+};
+
+/* controller at 0x200000 */
+&pci0 {
+ compatible = "fsl,p5020-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 1 15>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 15>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 40 1 0 0
+ 0000 0 0 2 &mpic 1 1 0 0
+ 0000 0 0 3 &mpic 2 1 0 0
+ 0000 0 0 4 &mpic 3 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x201000 */
+&pci1 {
+ compatible = "fsl,p5020-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 1 14>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 14>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 41 1 0 0
+ 0000 0 0 2 &mpic 5 1 0 0
+ 0000 0 0 3 &mpic 6 1 0 0
+ 0000 0 0 4 &mpic 7 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x202000 */
+&pci2 {
+ compatible = "fsl,p5020-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 1 13>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 13>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 42 1 0 0
+ 0000 0 0 2 &mpic 9 1 0 0
+ 0000 0 0 3 &mpic 10 1 0 0
+ 0000 0 0 4 &mpic 11 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x203000 */
+&pci3 {
+ compatible = "fsl,p5020-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 1 12>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 12>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 43 1 0 0
+ 0000 0 0 2 &mpic 0 1 0 0
+ 0000 0 0 3 &mpic 4 1 0 0
+ 0000 0 0 4 &mpic 8 1 0 0
+ >;
+ };
+};
+
+&dcsr {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,dcsr", "simple-bus";
+
+ dcsr-epu@0 {
+ compatible = "fsl,dcsr-epu";
+ interrupts = <52 2 0 0
+ 84 2 0 0
+ 85 2 0 0>;
+ reg = <0x0 0x1000>;
+ };
+ dcsr-npc {
+ compatible = "fsl,dcsr-npc";
+ reg = <0x1000 0x1000 0x1000000 0x8000>;
+ };
+ dcsr-nxc@2000 {
+ compatible = "fsl,dcsr-nxc";
+ reg = <0x2000 0x1000>;
+ };
+ dcsr-corenet {
+ compatible = "fsl,dcsr-corenet";
+ reg = <0x8000 0x1000 0xB0000 0x1000>;
+ };
+ dcsr-dpaa@9000 {
+ compatible = "fsl,p5020-dcsr-dpaa", "fsl,dcsr-dpaa";
+ reg = <0x9000 0x1000>;
+ };
+ dcsr-ocn@11000 {
+ compatible = "fsl,p5020-dcsr-ocn", "fsl,dcsr-ocn";
+ reg = <0x11000 0x1000>;
+ };
+ dcsr-ddr@12000 {
+ compatible = "fsl,dcsr-ddr";
+ dev-handle = <&ddr1>;
+ reg = <0x12000 0x1000>;
+ };
+ dcsr-ddr@13000 {
+ compatible = "fsl,dcsr-ddr";
+ dev-handle = <&ddr2>;
+ reg = <0x13000 0x1000>;
+ };
+ dcsr-nal@18000 {
+ compatible = "fsl,p5020-dcsr-nal", "fsl,dcsr-nal";
+ reg = <0x18000 0x1000>;
+ };
+ dcsr-rcpm@22000 {
+ compatible = "fsl,p5020-dcsr-rcpm", "fsl,dcsr-rcpm";
+ reg = <0x22000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@40000 {
+ compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu0>;
+ reg = <0x40000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@41000 {
+ compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu1>;
+ reg = <0x41000 0x1000>;
+ };
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "simple-bus";
+
+ soc-sram-error {
+ compatible = "fsl,soc-sram-error";
+ interrupts = <16 2 1 29>;
+ };
+
+ corenet-law@0 {
+ compatible = "fsl,corenet-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <32>;
+ };
+
+ ddr1: memory-controller@8000 {
+ compatible = "fsl,qoriq-memory-controller-v4.5", "fsl,qoriq-memory-controller";
+ reg = <0x8000 0x1000>;
+ interrupts = <16 2 1 23>;
+ };
+
+ ddr2: memory-controller@9000 {
+ compatible = "fsl,qoriq-memory-controller-v4.5","fsl,qoriq-memory-controller";
+ reg = <0x9000 0x1000>;
+ interrupts = <16 2 1 22>;
+ };
+
+ cpc: l3-cache-controller@10000 {
+ compatible = "fsl,p5020-l3-cache-controller", "fsl,p4080-l3-cache-controller", "cache";
+ reg = <0x10000 0x1000
+ 0x11000 0x1000>;
+ interrupts = <16 2 1 27
+ 16 2 1 26>;
+ };
+
+ corenet-cf@18000 {
+ compatible = "fsl,corenet-cf";
+ reg = <0x18000 0x1000>;
+ interrupts = <16 2 1 31>;
+ fsl,ccf-num-csdids = <32>;
+ fsl,ccf-num-snoopids = <32>;
+ };
+
+ iommu@20000 {
+ compatible = "fsl,pamu-v1.0", "fsl,pamu";
+ reg = <0x20000 0x4000>;
+ interrupts = <
+ 24 2 0 0
+ 16 2 1 30>;
+ };
+
+/include/ "qoriq-mpic.dtsi"
+
+ guts: global-utilities@e0000 {
+ compatible = "fsl,qoriq-device-config-1.0";
+ reg = <0xe0000 0xe00>;
+ fsl,has-rstcr;
+ #sleep-cells = <1>;
+ fsl,liodn-bits = <12>;
+ };
+
+ pins: global-utilities@e0e00 {
+ compatible = "fsl,qoriq-pin-control-1.0";
+ reg = <0xe0e00 0x200>;
+ #sleep-cells = <2>;
+ };
+
+ clockgen: global-utilities@e1000 {
+ compatible = "fsl,p5020-clockgen", "fsl,qoriq-clockgen-1.0";
+ reg = <0xe1000 0x1000>;
+ clock-frequency = <0>;
+ };
+
+ rcpm: global-utilities@e2000 {
+ compatible = "fsl,qoriq-rcpm-1.0";
+ reg = <0xe2000 0x1000>;
+ #sleep-cells = <1>;
+ };
+
+ sfp: sfp@e8000 {
+ compatible = "fsl,p5020-sfp", "fsl,qoriq-sfp-1.0";
+ reg = <0xe8000 0x1000>;
+ };
+
+ serdes: serdes@ea000 {
+ compatible = "fsl,p5020-serdes";
+ reg = <0xea000 0x1000>;
+ };
+
+/include/ "qoriq-dma-0.dtsi"
+/include/ "qoriq-dma-1.dtsi"
+/include/ "qoriq-espi-0.dtsi"
+ spi@110000 {
+ fsl,espi-num-chipselects = <4>;
+ };
+
+/include/ "qoriq-esdhc-0.dtsi"
+ sdhc@114000 {
+ sdhci,auto-cmd12;
+ };
+
+/include/ "qoriq-i2c-0.dtsi"
+/include/ "qoriq-i2c-1.dtsi"
+/include/ "qoriq-duart-0.dtsi"
+/include/ "qoriq-duart-1.dtsi"
+/include/ "qoriq-gpio-0.dtsi"
+/include/ "qoriq-usb2-mph-0.dtsi"
+ usb0: usb@210000 {
+ phy_type = "utmi";
+ port0;
+ };
+
+/include/ "qoriq-usb2-dr-0.dtsi"
+ usb1: usb@211000 {
+ dr_mode = "host";
+ phy_type = "utmi";
+ };
+
+/include/ "qoriq-sata2-0.dtsi"
+/include/ "qoriq-sata2-1.dtsi"
+/include/ "qoriq-sec4.2-0.dtsi"
+};
diff --git a/arch/powerpc/boot/dts/fsl/p5020si-pre.dtsi b/arch/powerpc/boot/dts/fsl/p5020si-pre.dtsi
new file mode 100644
index 0000000..ae823a4
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p5020si-pre.dtsi
@@ -0,0 +1,96 @@
+/*
+ * P5020/P5010 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+ compatible = "fsl,P5020";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ ccsr = &soc;
+ dcsr = &dcsr;
+
+ serial0 = &serial0;
+ serial1 = &serial1;
+ serial2 = &serial2;
+ serial3 = &serial3;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
+ pci3 = &pci3;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ dma0 = &dma0;
+ dma1 = &dma1;
+ sdhc = &sdhc;
+ msi0 = &msi0;
+ msi1 = &msi1;
+ msi2 = &msi2;
+
+ crypto = &crypto;
+ sec_jr0 = &sec_jr0;
+ sec_jr1 = &sec_jr1;
+ sec_jr2 = &sec_jr2;
+ sec_jr3 = &sec_jr3;
+ rtic_a = &rtic_a;
+ rtic_b = &rtic_b;
+ rtic_c = &rtic_c;
+ rtic_d = &rtic_d;
+ sec_mon = &sec_mon;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: PowerPC,e5500@0 {
+ device_type = "cpu";
+ reg = <0>;
+ next-level-cache = <&L2_0>;
+ L2_0: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu1: PowerPC,e5500@1 {
+ device_type = "cpu";
+ reg = <1>;
+ next-level-cache = <&L2_1>;
+ L2_1: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p5020ds.dts b/arch/powerpc/boot/dts/p5020ds.dts
index e6d4099..ceee4f5 100644
--- a/arch/powerpc/boot/dts/p5020ds.dts
+++ b/arch/powerpc/boot/dts/p5020ds.dts
@@ -32,7 +32,7 @@
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
-/include/ "p5020si.dtsi"
+/include/ "fsl/p5020si-pre.dtsi"
/ {
model = "fsl,P5020DS";
@@ -50,6 +50,8 @@
};
soc: soc@ffe000000 {
+ ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+ reg = <0xf 0xfe000000 0 0x00001000>;
spi@110000 {
flash@0 {
#address-cells = <1>;
@@ -99,7 +101,7 @@
};
};
- localbus@ffe124000 {
+ lbc: localbus@ffe124000 {
reg = <0xf 0xfe124000 0 0x1000>;
ranges = <0 0 0xf 0xe8000000 0x08000000
2 0 0xf 0xffa00000 0x00040000
@@ -160,7 +162,7 @@
reg = <0xf 0xfe200000 0 0x1000>;
ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0x0 0x20000000
0x01000000 0 0x00000000 0xf 0xf8000000 0x0 0x00010000>;
-
+ fsl,msi = <&msi0>;
pcie@0 {
ranges = <0x02000000 0 0xe0000000
0x02000000 0 0xe0000000
@@ -176,6 +178,7 @@
reg = <0xf 0xfe201000 0 0x1000>;
ranges = <0x02000000 0x0 0xe0000000 0xc 0x20000000 0x0 0x20000000
0x01000000 0x0 0x00000000 0xf 0xf8010000 0x0 0x00010000>;
+ fsl,msi = <&msi1>;
pcie@0 {
ranges = <0x02000000 0 0xe0000000
0x02000000 0 0xe0000000
@@ -191,6 +194,7 @@
reg = <0xf 0xfe202000 0 0x1000>;
ranges = <0x02000000 0 0xe0000000 0xc 0x40000000 0 0x20000000
0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+ fsl,msi = <&msi2>;
pcie@0 {
ranges = <0x02000000 0 0xe0000000
0x02000000 0 0xe0000000
@@ -206,6 +210,7 @@
reg = <0xf 0xfe203000 0 0x1000>;
ranges = <0x02000000 0 0xe0000000 0xc 0x60000000 0 0x20000000
0x01000000 0 0x00000000 0xf 0xf8030000 0 0x00010000>;
+ fsl,msi = <&msi2>;
pcie@0 {
ranges = <0x02000000 0 0xe0000000
0x02000000 0 0xe0000000
@@ -217,3 +222,5 @@
};
};
};
+
+/include/ "fsl/p5020si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p5020si.dtsi b/arch/powerpc/boot/dts/p5020si.dtsi
deleted file mode 100644
index e7948ad..0000000
--- a/arch/powerpc/boot/dts/p5020si.dtsi
+++ /dev/null
@@ -1,716 +0,0 @@
-/*
- * P5020 Silicon Device Tree Source
- *
- * Copyright 2010-2011 Freescale Semiconductor Inc.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- * * Redistributions of source code must retain the above copyright
- * notice, this list of conditions and the following disclaimer.
- * * Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- * * Neither the name of Freescale Semiconductor nor the
- * names of its contributors may be used to endorse or promote products
- * derived from this software without specific prior written permission.
- *
- *
- * ALTERNATIVELY, this software may be distributed under the terms of the
- * GNU General Public License ("GPL") as published by the Free Software
- * Foundation, either version 2 of that License or (at your option) any
- * later version.
- *
- * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
- * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
- * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
- * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
- * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
- * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
- * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- */
-
-/dts-v1/;
-
-/ {
- compatible = "fsl,P5020";
- #address-cells = <2>;
- #size-cells = <2>;
- interrupt-parent = <&mpic>;
-
- aliases {
- ccsr = &soc;
- dcsr = &dcsr;
-
- serial0 = &serial0;
- serial1 = &serial1;
- serial2 = &serial2;
- serial3 = &serial3;
- pci0 = &pci0;
- pci1 = &pci1;
- pci2 = &pci2;
- pci3 = &pci3;
- usb0 = &usb0;
- usb1 = &usb1;
- dma0 = &dma0;
- dma1 = &dma1;
- sdhc = &sdhc;
- msi0 = &msi0;
- msi1 = &msi1;
- msi2 = &msi2;
-
- crypto = &crypto;
- sec_jr0 = &sec_jr0;
- sec_jr1 = &sec_jr1;
- sec_jr2 = &sec_jr2;
- sec_jr3 = &sec_jr3;
- rtic_a = &rtic_a;
- rtic_b = &rtic_b;
- rtic_c = &rtic_c;
- rtic_d = &rtic_d;
- sec_mon = &sec_mon;
-
-/*
- rio0 = &rapidio0;
- */
- };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu0: PowerPC,e5500@0 {
- device_type = "cpu";
- reg = <0>;
- next-level-cache = <&L2_0>;
- L2_0: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- cpu1: PowerPC,e5500@1 {
- device_type = "cpu";
- reg = <1>;
- next-level-cache = <&L2_1>;
- L2_1: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- };
-
- dcsr: dcsr@f00000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,dcsr", "simple-bus";
-
- dcsr-epu@0 {
- compatible = "fsl,dcsr-epu";
- interrupts = <52 2 0 0
- 84 2 0 0
- 85 2 0 0>;
- interrupt-parent = <&mpic>;
- reg = <0x0 0x1000>;
- };
- dcsr-npc {
- compatible = "fsl,dcsr-npc";
- reg = <0x1000 0x1000 0x1000000 0x8000>;
- };
- dcsr-nxc@2000 {
- compatible = "fsl,dcsr-nxc";
- reg = <0x2000 0x1000>;
- };
- dcsr-corenet {
- compatible = "fsl,dcsr-corenet";
- reg = <0x8000 0x1000 0xB0000 0x1000>;
- };
- dcsr-dpaa@9000 {
- compatible = "fsl,p5020-dcsr-dpaa", "fsl,dcsr-dpaa";
- reg = <0x9000 0x1000>;
- };
- dcsr-ocn@11000 {
- compatible = "fsl,p5020-dcsr-ocn", "fsl,dcsr-ocn";
- reg = <0x11000 0x1000>;
- };
- dcsr-ddr@12000 {
- compatible = "fsl,dcsr-ddr";
- dev-handle = <&ddr1>;
- reg = <0x12000 0x1000>;
- };
- dcsr-ddr@13000 {
- compatible = "fsl,dcsr-ddr";
- dev-handle = <&ddr2>;
- reg = <0x13000 0x1000>;
- };
- dcsr-nal@18000 {
- compatible = "fsl,p5020-dcsr-nal", "fsl,dcsr-nal";
- reg = <0x18000 0x1000>;
- };
- dcsr-rcpm@22000 {
- compatible = "fsl,p5020-dcsr-rcpm", "fsl,dcsr-rcpm";
- reg = <0x22000 0x1000>;
- };
- dcsr-cpu-sb-proxy@40000 {
- compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu0>;
- reg = <0x40000 0x1000>;
- };
- dcsr-cpu-sb-proxy@41000 {
- compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu1>;
- reg = <0x41000 0x1000>;
- };
- };
-
- soc: soc@ffe000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "soc";
- compatible = "simple-bus";
- ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
- reg = <0xf 0xfe000000 0 0x00001000>;
-
- soc-sram-error {
- compatible = "fsl,soc-sram-error";
- interrupts = <16 2 1 29>;
- };
-
- corenet-law@0 {
- compatible = "fsl,corenet-law";
- reg = <0x0 0x1000>;
- fsl,num-laws = <32>;
- };
-
- ddr1: memory-controller@8000 {
- compatible = "fsl,qoriq-memory-controller-v4.5", "fsl,qoriq-memory-controller";
- reg = <0x8000 0x1000>;
- interrupts = <16 2 1 23>;
- };
-
- ddr2: memory-controller@9000 {
- compatible = "fsl,qoriq-memory-controller-v4.5", "fsl,qoriq-memory-controller";
- reg = <0x9000 0x1000>;
- interrupts = <16 2 1 22>;
- };
-
- cpc: l3-cache-controller@10000 {
- compatible = "fsl,p5020-l3-cache-controller", "fsl,p4080-l3-cache-controller", "cache";
- reg = <0x10000 0x1000
- 0x11000 0x1000>;
- interrupts = <16 2 1 27
- 16 2 1 26>;
- };
-
- corenet-cf@18000 {
- compatible = "fsl,corenet-cf";
- reg = <0x18000 0x1000>;
- interrupts = <16 2 1 31>;
- fsl,ccf-num-csdids = <32>;
- fsl,ccf-num-snoopids = <32>;
- };
-
- iommu@20000 {
- compatible = "fsl,pamu-v1.0", "fsl,pamu";
- reg = <0x20000 0x4000>;
- interrupts = <
- 24 2 0 0
- 16 2 1 30>;
- };
-
- mpic: pic@40000 {
- clock-frequency = <0>;
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <4>;
- reg = <0x40000 0x40000>;
- compatible = "fsl,mpic", "chrp,open-pic";
- device_type = "open-pic";
- };
-
- msi0: msi@41600 {
- compatible = "fsl,mpic-msi";
- reg = <0x41600 0x200>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe0 0 0 0
- 0xe1 0 0 0
- 0xe2 0 0 0
- 0xe3 0 0 0
- 0xe4 0 0 0
- 0xe5 0 0 0
- 0xe6 0 0 0
- 0xe7 0 0 0>;
- };
-
- msi1: msi@41800 {
- compatible = "fsl,mpic-msi";
- reg = <0x41800 0x200>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe8 0 0 0
- 0xe9 0 0 0
- 0xea 0 0 0
- 0xeb 0 0 0
- 0xec 0 0 0
- 0xed 0 0 0
- 0xee 0 0 0
- 0xef 0 0 0>;
- };
-
- msi2: msi@41a00 {
- compatible = "fsl,mpic-msi";
- reg = <0x41a00 0x200>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xf0 0 0 0
- 0xf1 0 0 0
- 0xf2 0 0 0
- 0xf3 0 0 0
- 0xf4 0 0 0
- 0xf5 0 0 0
- 0xf6 0 0 0
- 0xf7 0 0 0>;
- };
-
- guts: global-utilities@e0000 {
- compatible = "fsl,qoriq-device-config-1.0";
- reg = <0xe0000 0xe00>;
- fsl,has-rstcr;
- #sleep-cells = <1>;
- fsl,liodn-bits = <12>;
- };
-
- pins: global-utilities@e0e00 {
- compatible = "fsl,qoriq-pin-control-1.0";
- reg = <0xe0e00 0x200>;
- #sleep-cells = <2>;
- };
-
- clockgen: global-utilities@e1000 {
- compatible = "fsl,p5020-clockgen", "fsl,qoriq-clockgen-1.0";
- reg = <0xe1000 0x1000>;
- clock-frequency = <0>;
- };
-
- rcpm: global-utilities@e2000 {
- compatible = "fsl,qoriq-rcpm-1.0";
- reg = <0xe2000 0x1000>;
- #sleep-cells = <1>;
- };
-
- sfp: sfp@e8000 {
- compatible = "fsl,p5020-sfp", "fsl,qoriq-sfp-1.0";
- reg = <0xe8000 0x1000>;
- };
-
- serdes: serdes@ea000 {
- compatible = "fsl,p5020-serdes";
- reg = <0xea000 0x1000>;
- };
-
- dma0: dma@100300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,p5020-dma", "fsl,eloplus-dma";
- reg = <0x100300 0x4>;
- ranges = <0x0 0x100100 0x200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,p5020-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupts = <28 2 0 0>;
- };
- dma-channel@80 {
- compatible = "fsl,p5020-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupts = <29 2 0 0>;
- };
- dma-channel@100 {
- compatible = "fsl,p5020-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupts = <30 2 0 0>;
- };
- dma-channel@180 {
- compatible = "fsl,p5020-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupts = <31 2 0 0>;
- };
- };
-
- dma1: dma@101300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,p5020-dma", "fsl,eloplus-dma";
- reg = <0x101300 0x4>;
- ranges = <0x0 0x101100 0x200>;
- cell-index = <1>;
- dma-channel@0 {
- compatible = "fsl,p5020-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupts = <32 2 0 0>;
- };
- dma-channel@80 {
- compatible = "fsl,p5020-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupts = <33 2 0 0>;
- };
- dma-channel@100 {
- compatible = "fsl,p5020-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupts = <34 2 0 0>;
- };
- dma-channel@180 {
- compatible = "fsl,p5020-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupts = <35 2 0 0>;
- };
- };
-
- spi@110000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,p5020-espi", "fsl,mpc8536-espi";
- reg = <0x110000 0x1000>;
- interrupts = <53 0x2 0 0>;
- fsl,espi-num-chipselects = <4>;
- };
-
- sdhc: sdhc@114000 {
- compatible = "fsl,p5020-esdhc", "fsl,esdhc";
- reg = <0x114000 0x1000>;
- interrupts = <48 2 0 0>;
- sdhci,auto-cmd12;
- clock-frequency = <0>;
- };
-
- i2c@118000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x118000 0x100>;
- interrupts = <38 2 0 0>;
- dfsrr;
- };
-
- i2c@118100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- compatible = "fsl-i2c";
- reg = <0x118100 0x100>;
- interrupts = <38 2 0 0>;
- dfsrr;
- };
-
- i2c@119000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <2>;
- compatible = "fsl-i2c";
- reg = <0x119000 0x100>;
- interrupts = <39 2 0 0>;
- dfsrr;
- };
-
- i2c@119100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <3>;
- compatible = "fsl-i2c";
- reg = <0x119100 0x100>;
- interrupts = <39 2 0 0>;
- dfsrr;
- };
-
- serial0: serial@11c500 {
- cell-index = <0>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x11c500 0x100>;
- clock-frequency = <0>;
- interrupts = <36 2 0 0>;
- };
-
- serial1: serial@11c600 {
- cell-index = <1>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x11c600 0x100>;
- clock-frequency = <0>;
- interrupts = <36 2 0 0>;
- };
-
- serial2: serial@11d500 {
- cell-index = <2>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x11d500 0x100>;
- clock-frequency = <0>;
- interrupts = <37 2 0 0>;
- };
-
- serial3: serial@11d600 {
- cell-index = <3>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x11d600 0x100>;
- clock-frequency = <0>;
- interrupts = <37 2 0 0>;
- };
-
- gpio0: gpio@130000 {
- compatible = "fsl,p5020-gpio", "fsl,qoriq-gpio";
- reg = <0x130000 0x1000>;
- interrupts = <55 2 0 0>;
- #gpio-cells = <2>;
- gpio-controller;
- };
-
- usb0: usb@210000 {
- compatible = "fsl,p5020-usb2-mph",
- "fsl,mpc85xx-usb2-mph", "fsl-usb2-mph";
- reg = <0x210000 0x1000>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <44 0x2 0 0>;
- phy_type = "utmi";
- port0;
- };
-
- usb1: usb@211000 {
- compatible = "fsl,p5020-usb2-dr",
- "fsl,mpc85xx-usb2-dr", "fsl-usb2-dr";
- reg = <0x211000 0x1000>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <45 0x2 0 0>;
- dr_mode = "host";
- phy_type = "utmi";
- };
-
- sata@220000 {
- compatible = "fsl,p5020-sata", "fsl,pq-sata-v2";
- reg = <0x220000 0x1000>;
- interrupts = <68 0x2 0 0>;
- };
-
- sata@221000 {
- compatible = "fsl,p5020-sata", "fsl,pq-sata-v2";
- reg = <0x221000 0x1000>;
- interrupts = <69 0x2 0 0>;
- };
-
- crypto: crypto@300000 {
- compatible = "fsl,sec-v4.2", "fsl,sec-v4.0";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x300000 0x10000>;
- ranges = <0 0x300000 0x10000>;
- interrupts = <92 2 0 0>;
-
- sec_jr0: jr@1000 {
- compatible = "fsl,sec-v4.2-job-ring",
- "fsl,sec-v4.0-job-ring";
- reg = <0x1000 0x1000>;
- interrupts = <88 2 0 0>;
- };
-
- sec_jr1: jr@2000 {
- compatible = "fsl,sec-v4.2-job-ring",
- "fsl,sec-v4.0-job-ring";
- reg = <0x2000 0x1000>;
- interrupts = <89 2 0 0>;
- };
-
- sec_jr2: jr@3000 {
- compatible = "fsl,sec-v4.2-job-ring",
- "fsl,sec-v4.0-job-ring";
- reg = <0x3000 0x1000>;
- interrupts = <90 2 0 0>;
- };
-
- sec_jr3: jr@4000 {
- compatible = "fsl,sec-v4.2-job-ring",
- "fsl,sec-v4.0-job-ring";
- reg = <0x4000 0x1000>;
- interrupts = <91 2 0 0>;
- };
-
- rtic@6000 {
- compatible = "fsl,sec-v4.2-rtic",
- "fsl,sec-v4.0-rtic";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x6000 0x100>;
- ranges = <0x0 0x6100 0xe00>;
-
- rtic_a: rtic-a@0 {
- compatible = "fsl,sec-v4.2-rtic-memory",
- "fsl,sec-v4.0-rtic-memory";
- reg = <0x00 0x20 0x100 0x80>;
- };
-
- rtic_b: rtic-b@20 {
- compatible = "fsl,sec-v4.2-rtic-memory",
- "fsl,sec-v4.0-rtic-memory";
- reg = <0x20 0x20 0x200 0x80>;
- };
-
- rtic_c: rtic-c@40 {
- compatible = "fsl,sec-v4.2-rtic-memory",
- "fsl,sec-v4.0-rtic-memory";
- reg = <0x40 0x20 0x300 0x80>;
- };
-
- rtic_d: rtic-d@60 {
- compatible = "fsl,sec-v4.2-rtic-memory",
- "fsl,sec-v4.0-rtic-memory";
- reg = <0x60 0x20 0x500 0x80>;
- };
- };
- };
-
- sec_mon: sec_mon@314000 {
- compatible = "fsl,sec-v4.2-mon", "fsl,sec-v4.0-mon";
- reg = <0x314000 0x1000>;
- interrupts = <93 2 0 0>;
- };
- };
-
-/*
- rapidio0: rapidio@ffe0c0000
-*/
-
- localbus@ffe124000 {
- compatible = "fsl,p5020-elbc", "fsl,elbc", "simple-bus";
- interrupts = <25 2 0 0>;
- #address-cells = <2>;
- #size-cells = <1>;
- };
-
- pci0: pcie@ffe200000 {
- compatible = "fsl,p5020-pcie", "fsl,qoriq-pcie-v2.2";
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
- bus-range = <0x0 0xff>;
- clock-frequency = <0x1fca055>;
- fsl,msi = <&msi0>;
- interrupts = <16 2 1 15>;
-
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupts = <16 2 1 15>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0 0 1 &mpic 40 1 0 0
- 0000 0 0 2 &mpic 1 1 0 0
- 0000 0 0 3 &mpic 2 1 0 0
- 0000 0 0 4 &mpic 3 1 0 0
- >;
- };
- };
-
- pci1: pcie@ffe201000 {
- compatible = "fsl,p5020-pcie", "fsl,qoriq-pcie-v2.2";
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
- bus-range = <0 0xff>;
- clock-frequency = <0x1fca055>;
- fsl,msi = <&msi1>;
- interrupts = <16 2 1 14>;
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupts = <16 2 1 14>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0 0 1 &mpic 41 1 0 0
- 0000 0 0 2 &mpic 5 1 0 0
- 0000 0 0 3 &mpic 6 1 0 0
- 0000 0 0 4 &mpic 7 1 0 0
- >;
- };
- };
-
- pci2: pcie@ffe202000 {
- compatible = "fsl,p5020-pcie", "fsl,qoriq-pcie-v2.2";
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
- bus-range = <0x0 0xff>;
- clock-frequency = <0x1fca055>;
- fsl,msi = <&msi2>;
- interrupts = <16 2 1 13>;
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupts = <16 2 1 13>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0 0 1 &mpic 42 1 0 0
- 0000 0 0 2 &mpic 9 1 0 0
- 0000 0 0 3 &mpic 10 1 0 0
- 0000 0 0 4 &mpic 11 1 0 0
- >;
- };
- };
-
- pci3: pcie@ffe203000 {
- compatible = "fsl,p5020-pcie", "fsl,qoriq-pcie-v2.2";
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
- bus-range = <0x0 0xff>;
- clock-frequency = <0x1fca055>;
- fsl,msi = <&msi2>;
- interrupts = <16 2 1 12>;
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupts = <16 2 1 12>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0 0 1 &mpic 43 1 0 0
- 0000 0 0 2 &mpic 0 1 0 0
- 0000 0 0 3 &mpic 4 1 0 0
- 0000 0 0 4 &mpic 8 1 0 0
- >;
- };
- };
-};
--
1.7.3.4
^ permalink raw reply related
* oprofile callgraph support missing for common cpus
From: Joakim Tjernlund @ 2011-11-17 8:38 UTC (permalink / raw)
To: linuxppc-dev; +Cc: oprofile-list
arch/powerpc/oprofile/common.c has this init code:
int __init oprofile_arch_init(struct oprofile_operations *ops)
{
if (!cur_cpu_spec->oprofile_cpu_type)
return -ENODEV;
if (firmware_has_feature(FW_FEATURE_ISERIES))
return -ENODEV;
switch (cur_cpu_spec->oprofile_type) {
#ifdef CONFIG_PPC_BOOK3S_64
#ifdef CONFIG_OPROFILE_CELL
case PPC_OPROFILE_CELL:
if (firmware_has_feature(FW_FEATURE_LPAR))
return -ENODEV;
model = &op_model_cell;
ops->sync_start = model->sync_start;
ops->sync_stop = model->sync_stop;
break;
#endif
case PPC_OPROFILE_RS64:
model = &op_model_rs64;
break;
case PPC_OPROFILE_POWER4:
model = &op_model_power4;
break;
case PPC_OPROFILE_PA6T:
model = &op_model_pa6t;
break;
#endif
#ifdef CONFIG_6xx
case PPC_OPROFILE_G4:
model = &op_model_7450;
break;
#endif
#if defined(CONFIG_FSL_EMB_PERFMON)
case PPC_OPROFILE_FSL_EMB:
model = &op_model_fsl_emb;
break;
#endif
default:
return -ENODEV;
}
model->num_counters = cur_cpu_spec->num_pmcs;
ops->cpu_type = cur_cpu_spec->oprofile_cpu_type;
ops->create_files = op_powerpc_create_files;
ops->setup = op_powerpc_setup;
ops->shutdown = op_powerpc_shutdown;
ops->start = op_powerpc_start;
ops->stop = op_powerpc_stop;
ops->backtrace = op_powerpc_backtrace;
}
Notice the first
if (!cur_cpu_spec->oprofile_cpu_type)
return -ENODEV;
if (firmware_has_feature(FW_FEATURE_ISERIES))
return -ENODEV;
For my e300c2 cpu both if's are false and I don't get support for callgraph/backtrace
support. Moving the ops->backtrace = op_powerpc_backtrace; to the top
enables backtrace for me.
This function needs fixing so its not all or nothing but I cannot make out
what is what so please, could someone look at this?
I am somewhat behind mainline so I will just use my hack for now.
Jocke
^ permalink raw reply
* AFDX Support in Linux
From: Vineeth @ 2011-11-17 8:00 UTC (permalink / raw)
To: linuxppc-dev, linux-embedded
[-- Attachment #1: Type: text/plain, Size: 89 bytes --]
Do we have AFDX support in Linux/Rt-Linux ?
tried grep.couldnt find any.
Thanks
Vineeth
[-- Attachment #2: Type: text/html, Size: 105 bytes --]
^ permalink raw reply
* [PATCH 28/29] powerpc/85xx: Rework P4080DS device trees
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-27-git-send-email-galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p4080-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/fsl/p4080si-post.dtsi | 342 ++++++++++++
arch/powerpc/boot/dts/fsl/p4080si-pre.dtsi | 145 +++++
arch/powerpc/boot/dts/p4080ds.dts | 14 +-
arch/powerpc/boot/dts/p4080si.dtsi | 755 ---------------------------
4 files changed, 498 insertions(+), 758 deletions(-)
create mode 100644 arch/powerpc/boot/dts/fsl/p4080si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/p4080si-pre.dtsi
delete mode 100644 arch/powerpc/boot/dts/p4080si.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/p4080si-post.dtsi b/arch/powerpc/boot/dts/fsl/p4080si-post.dtsi
new file mode 100644
index 0000000..1510991
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p4080si-post.dtsi
@@ -0,0 +1,342 @@
+/*
+ * P4080/P4040 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ compatible = "fsl,p4080-elbc", "fsl,elbc", "simple-bus";
+ interrupts = <25 2 0 0>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+};
+
+/* controller at 0x200000 */
+&pci0 {
+ compatible = "fsl,p4080-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 1 15>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 15>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 40 1 0 0
+ 0000 0 0 2 &mpic 1 1 0 0
+ 0000 0 0 3 &mpic 2 1 0 0
+ 0000 0 0 4 &mpic 3 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x201000 */
+&pci1 {
+ compatible = "fsl,p4080-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 1 14>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 14>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 41 1 0 0
+ 0000 0 0 2 &mpic 5 1 0 0
+ 0000 0 0 3 &mpic 6 1 0 0
+ 0000 0 0 4 &mpic 7 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x202000 */
+&pci2 {
+ compatible = "fsl,p4080-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 1 13>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 13>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 42 1 0 0
+ 0000 0 0 2 &mpic 9 1 0 0
+ 0000 0 0 3 &mpic 10 1 0 0
+ 0000 0 0 4 &mpic 11 1 0 0
+ >;
+ };
+};
+
+&rio {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "fsl,rapidio-delta";
+ interrupts = <
+ 16 2 1 11 /* err_irq */
+ 56 2 0 0 /* bell_outb_irq */
+ 57 2 0 0 /* bell_inb_irq */
+ 60 2 0 0 /* msg1_tx_irq */
+ 61 2 0 0 /* msg1_rx_irq */
+ 62 2 0 0 /* msg2_tx_irq */
+ 63 2 0 0>; /* msg2_rx_irq */
+};
+
+&dcsr {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,dcsr", "simple-bus";
+
+ dcsr-epu@0 {
+ compatible = "fsl,dcsr-epu";
+ interrupts = <52 2 0 0
+ 84 2 0 0
+ 85 2 0 0>;
+ reg = <0x0 0x1000>;
+ };
+ dcsr-npc {
+ compatible = "fsl,dcsr-npc";
+ reg = <0x1000 0x1000 0x1000000 0x8000>;
+ };
+ dcsr-nxc@2000 {
+ compatible = "fsl,dcsr-nxc";
+ reg = <0x2000 0x1000>;
+ };
+ dcsr-corenet {
+ compatible = "fsl,dcsr-corenet";
+ reg = <0x8000 0x1000 0xB0000 0x1000>;
+ };
+ dcsr-dpaa@9000 {
+ compatible = "fsl,p4080-dcsr-dpaa", "fsl,dcsr-dpaa";
+ reg = <0x9000 0x1000>;
+ };
+ dcsr-ocn@11000 {
+ compatible = "fsl,p4080-dcsr-ocn", "fsl,dcsr-ocn";
+ reg = <0x11000 0x1000>;
+ };
+ dcsr-ddr@12000 {
+ compatible = "fsl,dcsr-ddr";
+ dev-handle = <&ddr1>;
+ reg = <0x12000 0x1000>;
+ };
+ dcsr-ddr@13000 {
+ compatible = "fsl,dcsr-ddr";
+ dev-handle = <&ddr2>;
+ reg = <0x13000 0x1000>;
+ };
+ dcsr-nal@18000 {
+ compatible = "fsl,p4080-dcsr-nal", "fsl,dcsr-nal";
+ reg = <0x18000 0x1000>;
+ };
+ dcsr-rcpm@22000 {
+ compatible = "fsl,p4080-dcsr-rcpm", "fsl,dcsr-rcpm";
+ reg = <0x22000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@40000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu0>;
+ reg = <0x40000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@41000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu1>;
+ reg = <0x41000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@42000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu2>;
+ reg = <0x42000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@43000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu3>;
+ reg = <0x43000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@44000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu4>;
+ reg = <0x44000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@45000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu5>;
+ reg = <0x45000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@46000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu6>;
+ reg = <0x46000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@47000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu7>;
+ reg = <0x47000 0x1000>;
+ };
+
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "simple-bus";
+
+ soc-sram-error {
+ compatible = "fsl,soc-sram-error";
+ interrupts = <16 2 1 29>;
+ };
+
+ corenet-law@0 {
+ compatible = "fsl,corenet-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <32>;
+ };
+
+ ddr1: memory-controller@8000 {
+ compatible = "fsl,qoriq-memory-controller-v4.4", "fsl,qoriq-memory-controller";
+ reg = <0x8000 0x1000>;
+ interrupts = <16 2 1 23>;
+ };
+
+ ddr2: memory-controller@9000 {
+ compatible = "fsl,qoriq-memory-controller-v4.4","fsl,qoriq-memory-controller";
+ reg = <0x9000 0x1000>;
+ interrupts = <16 2 1 22>;
+ };
+
+ cpc: l3-cache-controller@10000 {
+ compatible = "fsl,p4080-l3-cache-controller", "cache";
+ reg = <0x10000 0x1000
+ 0x11000 0x1000>;
+ interrupts = <16 2 1 27
+ 16 2 1 26>;
+ };
+
+ corenet-cf@18000 {
+ compatible = "fsl,corenet-cf";
+ reg = <0x18000 0x1000>;
+ interrupts = <16 2 1 31>;
+ fsl,ccf-num-csdids = <32>;
+ fsl,ccf-num-snoopids = <32>;
+ };
+
+ iommu@20000 {
+ compatible = "fsl,pamu-v1.0", "fsl,pamu";
+ reg = <0x20000 0x5000>;
+ interrupts = <
+ 24 2 0 0
+ 16 2 1 30>;
+ };
+
+/include/ "qoriq-mpic.dtsi"
+
+ guts: global-utilities@e0000 {
+ compatible = "fsl,qoriq-device-config-1.0";
+ reg = <0xe0000 0xe00>;
+ fsl,has-rstcr;
+ #sleep-cells = <1>;
+ fsl,liodn-bits = <12>;
+ };
+
+ pins: global-utilities@e0e00 {
+ compatible = "fsl,qoriq-pin-control-1.0";
+ reg = <0xe0e00 0x200>;
+ #sleep-cells = <2>;
+ };
+
+ clockgen: global-utilities@e1000 {
+ compatible = "fsl,p4080-clockgen", "fsl,qoriq-clockgen-1.0";
+ reg = <0xe1000 0x1000>;
+ clock-frequency = <0>;
+ };
+
+ rcpm: global-utilities@e2000 {
+ compatible = "fsl,qoriq-rcpm-1.0";
+ reg = <0xe2000 0x1000>;
+ #sleep-cells = <1>;
+ };
+
+ sfp: sfp@e8000 {
+ compatible = "fsl,p4080-sfp", "fsl,qoriq-sfp-1.0";
+ reg = <0xe8000 0x1000>;
+ };
+
+ serdes: serdes@ea000 {
+ compatible = "fsl,p4080-serdes";
+ reg = <0xea000 0x1000>;
+ };
+
+/include/ "qoriq-dma-0.dtsi"
+/include/ "qoriq-dma-1.dtsi"
+/include/ "qoriq-espi-0.dtsi"
+ spi@110000 {
+ fsl,espi-num-chipselects = <4>;
+ };
+
+/include/ "qoriq-esdhc-0.dtsi"
+ sdhc@114000 {
+ voltage-ranges = <3300 3300>;
+ sdhci,auto-cmd12;
+ };
+
+/include/ "qoriq-i2c-0.dtsi"
+/include/ "qoriq-i2c-1.dtsi"
+/include/ "qoriq-duart-0.dtsi"
+/include/ "qoriq-duart-1.dtsi"
+/include/ "qoriq-gpio-0.dtsi"
+/include/ "qoriq-usb2-mph-0.dtsi"
+/include/ "qoriq-usb2-dr-0.dtsi"
+/include/ "qoriq-sec4.0-0.dtsi"
+};
diff --git a/arch/powerpc/boot/dts/fsl/p4080si-pre.dtsi b/arch/powerpc/boot/dts/fsl/p4080si-pre.dtsi
new file mode 100644
index 0000000..b353ac9
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p4080si-pre.dtsi
@@ -0,0 +1,145 @@
+/*
+ * P4080/P4040 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+ compatible = "fsl,P4080";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ ccsr = &soc;
+ dcsr = &dcsr;
+
+ serial0 = &serial0;
+ serial1 = &serial1;
+ serial2 = &serial2;
+ serial3 = &serial3;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ dma0 = &dma0;
+ dma1 = &dma1;
+ sdhc = &sdhc;
+ msi0 = &msi0;
+ msi1 = &msi1;
+ msi2 = &msi2;
+
+ crypto = &crypto;
+ sec_jr0 = &sec_jr0;
+ sec_jr1 = &sec_jr1;
+ sec_jr2 = &sec_jr2;
+ sec_jr3 = &sec_jr3;
+ rtic_a = &rtic_a;
+ rtic_b = &rtic_b;
+ rtic_c = &rtic_c;
+ rtic_d = &rtic_d;
+ sec_mon = &sec_mon;
+
+ rio0 = &rapidio0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: PowerPC,e500mc@0 {
+ device_type = "cpu";
+ reg = <0>;
+ next-level-cache = <&L2_0>;
+ L2_0: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu1: PowerPC,e500mc@1 {
+ device_type = "cpu";
+ reg = <1>;
+ next-level-cache = <&L2_1>;
+ L2_1: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu2: PowerPC,e500mc@2 {
+ device_type = "cpu";
+ reg = <2>;
+ next-level-cache = <&L2_2>;
+ L2_2: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu3: PowerPC,e500mc@3 {
+ device_type = "cpu";
+ reg = <3>;
+ next-level-cache = <&L2_3>;
+ L2_3: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu4: PowerPC,e500mc@4 {
+ device_type = "cpu";
+ reg = <4>;
+ next-level-cache = <&L2_4>;
+ L2_4: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu5: PowerPC,e500mc@5 {
+ device_type = "cpu";
+ reg = <5>;
+ next-level-cache = <&L2_5>;
+ L2_5: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu6: PowerPC,e500mc@6 {
+ device_type = "cpu";
+ reg = <6>;
+ next-level-cache = <&L2_6>;
+ L2_6: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu7: PowerPC,e500mc@7 {
+ device_type = "cpu";
+ reg = <7>;
+ next-level-cache = <&L2_7>;
+ L2_7: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p4080ds.dts b/arch/powerpc/boot/dts/p4080ds.dts
index c7916dc..8ea1ae9 100644
--- a/arch/powerpc/boot/dts/p4080ds.dts
+++ b/arch/powerpc/boot/dts/p4080ds.dts
@@ -32,7 +32,7 @@
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
-/include/ "p4080si.dtsi"
+/include/ "fsl/p4080si-pre.dtsi"
/ {
model = "fsl,P4080DS";
@@ -50,6 +50,9 @@
};
soc: soc@ffe000000 {
+ ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+ reg = <0xf 0xfe000000 0 0x00001000>;
+
spi@110000 {
flash@0 {
#address-cells = <1>;
@@ -105,12 +108,12 @@
};
};
- rapidio0: rapidio@ffe0c0000 {
+ rio: rapidio0: rapidio@ffe0c0000 {
reg = <0xf 0xfe0c0000 0 0x20000>;
ranges = <0 0 0xc 0x20000000 0 0x01000000>;
};
- localbus@ffe124000 {
+ lbc: localbus@ffe124000 {
reg = <0xf 0xfe124000 0 0x1000>;
ranges = <0 0 0xf 0xe8000000 0x08000000
3 0 0xf 0xffdf0000 0x00008000>;
@@ -132,6 +135,7 @@
reg = <0xf 0xfe200000 0 0x1000>;
ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0x0 0x20000000
0x01000000 0 0x00000000 0xf 0xf8000000 0x0 0x00010000>;
+ fsl,msi = <&msi0>;
pcie@0 {
ranges = <0x02000000 0 0xe0000000
0x02000000 0 0xe0000000
@@ -147,6 +151,7 @@
reg = <0xf 0xfe201000 0 0x1000>;
ranges = <0x02000000 0x0 0xe0000000 0xc 0x20000000 0x0 0x20000000
0x01000000 0x0 0x00000000 0xf 0xf8010000 0x0 0x00010000>;
+ fsl,msi = <&msi1>;
pcie@0 {
ranges = <0x02000000 0 0xe0000000
0x02000000 0 0xe0000000
@@ -162,6 +167,7 @@
reg = <0xf 0xfe202000 0 0x1000>;
ranges = <0x02000000 0 0xe0000000 0xc 0x40000000 0 0x20000000
0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+ fsl,msi = <&msi2>;
pcie@0 {
ranges = <0x02000000 0 0xe0000000
0x02000000 0 0xe0000000
@@ -174,3 +180,5 @@
};
};
+
+/include/ "fsl/p4080si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p4080si.dtsi b/arch/powerpc/boot/dts/p4080si.dtsi
deleted file mode 100644
index f20c01a..0000000
--- a/arch/powerpc/boot/dts/p4080si.dtsi
+++ /dev/null
@@ -1,755 +0,0 @@
-/*
- * P4080 Silicon Device Tree Source
- *
- * Copyright 2009-2011 Freescale Semiconductor Inc.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- * * Redistributions of source code must retain the above copyright
- * notice, this list of conditions and the following disclaimer.
- * * Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- * * Neither the name of Freescale Semiconductor nor the
- * names of its contributors may be used to endorse or promote products
- * derived from this software without specific prior written permission.
- *
- *
- * ALTERNATIVELY, this software may be distributed under the terms of the
- * GNU General Public License ("GPL") as published by the Free Software
- * Foundation, either version 2 of that License or (at your option) any
- * later version.
- *
- * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
- * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
- * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
- * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
- * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
- * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
- * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- */
-
-/dts-v1/;
-
-/ {
- compatible = "fsl,P4080";
- #address-cells = <2>;
- #size-cells = <2>;
- interrupt-parent = <&mpic>;
-
- aliases {
- ccsr = &soc;
- dcsr = &dcsr;
-
- serial0 = &serial0;
- serial1 = &serial1;
- serial2 = &serial2;
- serial3 = &serial3;
- pci0 = &pci0;
- pci1 = &pci1;
- pci2 = &pci2;
- usb0 = &usb0;
- usb1 = &usb1;
- dma0 = &dma0;
- dma1 = &dma1;
- sdhc = &sdhc;
- msi0 = &msi0;
- msi1 = &msi1;
- msi2 = &msi2;
-
- crypto = &crypto;
- sec_jr0 = &sec_jr0;
- sec_jr1 = &sec_jr1;
- sec_jr2 = &sec_jr2;
- sec_jr3 = &sec_jr3;
- rtic_a = &rtic_a;
- rtic_b = &rtic_b;
- rtic_c = &rtic_c;
- rtic_d = &rtic_d;
- sec_mon = &sec_mon;
-
- rio0 = &rapidio0;
- };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu0: PowerPC,e500mc@0 {
- device_type = "cpu";
- reg = <0>;
- next-level-cache = <&L2_0>;
- L2_0: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- cpu1: PowerPC,e500mc@1 {
- device_type = "cpu";
- reg = <1>;
- next-level-cache = <&L2_1>;
- L2_1: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- cpu2: PowerPC,e500mc@2 {
- device_type = "cpu";
- reg = <2>;
- next-level-cache = <&L2_2>;
- L2_2: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- cpu3: PowerPC,e500mc@3 {
- device_type = "cpu";
- reg = <3>;
- next-level-cache = <&L2_3>;
- L2_3: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- cpu4: PowerPC,e500mc@4 {
- device_type = "cpu";
- reg = <4>;
- next-level-cache = <&L2_4>;
- L2_4: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- cpu5: PowerPC,e500mc@5 {
- device_type = "cpu";
- reg = <5>;
- next-level-cache = <&L2_5>;
- L2_5: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- cpu6: PowerPC,e500mc@6 {
- device_type = "cpu";
- reg = <6>;
- next-level-cache = <&L2_6>;
- L2_6: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- cpu7: PowerPC,e500mc@7 {
- device_type = "cpu";
- reg = <7>;
- next-level-cache = <&L2_7>;
- L2_7: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- };
-
- dcsr: dcsr@f00000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,dcsr", "simple-bus";
-
- dcsr-epu@0 {
- compatible = "fsl,dcsr-epu";
- interrupts = <52 2 0 0
- 84 2 0 0
- 85 2 0 0>;
- interrupt-parent = <&mpic>;
- reg = <0x0 0x1000>;
- };
- dcsr-npc {
- compatible = "fsl,dcsr-npc";
- reg = <0x1000 0x1000 0x1000000 0x8000>;
- };
- dcsr-nxc@2000 {
- compatible = "fsl,dcsr-nxc";
- reg = <0x2000 0x1000>;
- };
- dcsr-corenet {
- compatible = "fsl,dcsr-corenet";
- reg = <0x8000 0x1000 0xB0000 0x1000>;
- };
- dcsr-dpaa@9000 {
- compatible = "fsl,p4080-dcsr-dpaa", "fsl,dcsr-dpaa";
- reg = <0x9000 0x1000>;
- };
- dcsr-ocn@11000 {
- compatible = "fsl,p4080-dcsr-ocn", "fsl,dcsr-ocn";
- reg = <0x11000 0x1000>;
- };
- dcsr-ddr@12000 {
- compatible = "fsl,dcsr-ddr";
- dev-handle = <&ddr1>;
- reg = <0x12000 0x1000>;
- };
- dcsr-ddr@13000 {
- compatible = "fsl,dcsr-ddr";
- dev-handle = <&ddr2>;
- reg = <0x13000 0x1000>;
- };
- dcsr-nal@18000 {
- compatible = "fsl,p4080-dcsr-nal", "fsl,dcsr-nal";
- reg = <0x18000 0x1000>;
- };
- dcsr-rcpm@22000 {
- compatible = "fsl,p4080-dcsr-rcpm", "fsl,dcsr-rcpm";
- reg = <0x22000 0x1000>;
- };
- dcsr-cpu-sb-proxy@40000 {
- compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu0>;
- reg = <0x40000 0x1000>;
- };
- dcsr-cpu-sb-proxy@41000 {
- compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu1>;
- reg = <0x41000 0x1000>;
- };
- dcsr-cpu-sb-proxy@42000 {
- compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu2>;
- reg = <0x42000 0x1000>;
- };
- dcsr-cpu-sb-proxy@43000 {
- compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu3>;
- reg = <0x43000 0x1000>;
- };
- dcsr-cpu-sb-proxy@44000 {
- compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu4>;
- reg = <0x44000 0x1000>;
- };
- dcsr-cpu-sb-proxy@45000 {
- compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu5>;
- reg = <0x45000 0x1000>;
- };
- dcsr-cpu-sb-proxy@46000 {
- compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu6>;
- reg = <0x46000 0x1000>;
- };
- dcsr-cpu-sb-proxy@47000 {
- compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu7>;
- reg = <0x47000 0x1000>;
- };
- };
-
- soc: soc@ffe000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "soc";
- compatible = "simple-bus";
- ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
- reg = <0xf 0xfe000000 0 0x00001000>;
-
- soc-sram-error {
- compatible = "fsl,soc-sram-error";
- interrupts = <16 2 1 29>;
- };
-
- corenet-law@0 {
- compatible = "fsl,corenet-law";
- reg = <0x0 0x1000>;
- fsl,num-laws = <32>;
- };
-
- ddr1: memory-controller@8000 {
- compatible = "fsl,qoriq-memory-controller-v4.4", "fsl,qoriq-memory-controller";
- reg = <0x8000 0x1000>;
- interrupts = <16 2 1 23>;
- };
-
- ddr2: memory-controller@9000 {
- compatible = "fsl,qoriq-memory-controller-v4.4","fsl,qoriq-memory-controller";
- reg = <0x9000 0x1000>;
- interrupts = <16 2 1 22>;
- };
-
- cpc: l3-cache-controller@10000 {
- compatible = "fsl,p4080-l3-cache-controller", "cache";
- reg = <0x10000 0x1000
- 0x11000 0x1000>;
- interrupts = <16 2 1 27
- 16 2 1 26>;
- };
-
- corenet-cf@18000 {
- compatible = "fsl,corenet-cf";
- reg = <0x18000 0x1000>;
- interrupts = <16 2 1 31>;
- fsl,ccf-num-csdids = <32>;
- fsl,ccf-num-snoopids = <32>;
- };
-
- iommu@20000 {
- compatible = "fsl,pamu-v1.0", "fsl,pamu";
- reg = <0x20000 0x5000>;
- interrupts = <
- 24 2 0 0
- 16 2 1 30>;
- };
-
- mpic: pic@40000 {
- clock-frequency = <0>;
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <4>;
- reg = <0x40000 0x40000>;
- compatible = "fsl,mpic", "chrp,open-pic";
- device_type = "open-pic";
- };
-
- msi0: msi@41600 {
- compatible = "fsl,mpic-msi";
- reg = <0x41600 0x200>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe0 0 0 0
- 0xe1 0 0 0
- 0xe2 0 0 0
- 0xe3 0 0 0
- 0xe4 0 0 0
- 0xe5 0 0 0
- 0xe6 0 0 0
- 0xe7 0 0 0>;
- };
-
- msi1: msi@41800 {
- compatible = "fsl,mpic-msi";
- reg = <0x41800 0x200>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe8 0 0 0
- 0xe9 0 0 0
- 0xea 0 0 0
- 0xeb 0 0 0
- 0xec 0 0 0
- 0xed 0 0 0
- 0xee 0 0 0
- 0xef 0 0 0>;
- };
-
- msi2: msi@41a00 {
- compatible = "fsl,mpic-msi";
- reg = <0x41a00 0x200>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xf0 0 0 0
- 0xf1 0 0 0
- 0xf2 0 0 0
- 0xf3 0 0 0
- 0xf4 0 0 0
- 0xf5 0 0 0
- 0xf6 0 0 0
- 0xf7 0 0 0>;
- };
-
- guts: global-utilities@e0000 {
- compatible = "fsl,qoriq-device-config-1.0";
- reg = <0xe0000 0xe00>;
- fsl,has-rstcr;
- #sleep-cells = <1>;
- fsl,liodn-bits = <12>;
- };
-
- pins: global-utilities@e0e00 {
- compatible = "fsl,qoriq-pin-control-1.0";
- reg = <0xe0e00 0x200>;
- #sleep-cells = <2>;
- };
-
- clockgen: global-utilities@e1000 {
- compatible = "fsl,p4080-clockgen", "fsl,qoriq-clockgen-1.0";
- reg = <0xe1000 0x1000>;
- clock-frequency = <0>;
- };
-
- rcpm: global-utilities@e2000 {
- compatible = "fsl,qoriq-rcpm-1.0";
- reg = <0xe2000 0x1000>;
- #sleep-cells = <1>;
- };
-
- sfp: sfp@e8000 {
- compatible = "fsl,p4080-sfp", "fsl,qoriq-sfp-1.0";
- reg = <0xe8000 0x1000>;
- };
-
- serdes: serdes@ea000 {
- compatible = "fsl,p4080-serdes";
- reg = <0xea000 0x1000>;
- };
-
- dma0: dma@100300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,p4080-dma", "fsl,eloplus-dma";
- reg = <0x100300 0x4>;
- ranges = <0x0 0x100100 0x200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,p4080-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupts = <28 2 0 0>;
- };
- dma-channel@80 {
- compatible = "fsl,p4080-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupts = <29 2 0 0>;
- };
- dma-channel@100 {
- compatible = "fsl,p4080-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupts = <30 2 0 0>;
- };
- dma-channel@180 {
- compatible = "fsl,p4080-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupts = <31 2 0 0>;
- };
- };
-
- dma1: dma@101300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,p4080-dma", "fsl,eloplus-dma";
- reg = <0x101300 0x4>;
- ranges = <0x0 0x101100 0x200>;
- cell-index = <1>;
- dma-channel@0 {
- compatible = "fsl,p4080-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupts = <32 2 0 0>;
- };
- dma-channel@80 {
- compatible = "fsl,p4080-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupts = <33 2 0 0>;
- };
- dma-channel@100 {
- compatible = "fsl,p4080-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupts = <34 2 0 0>;
- };
- dma-channel@180 {
- compatible = "fsl,p4080-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupts = <35 2 0 0>;
- };
- };
-
- spi@110000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,p4080-espi", "fsl,mpc8536-espi";
- reg = <0x110000 0x1000>;
- interrupts = <53 0x2 0 0>;
- fsl,espi-num-chipselects = <4>;
- };
-
- sdhc: sdhc@114000 {
- compatible = "fsl,p4080-esdhc", "fsl,esdhc";
- reg = <0x114000 0x1000>;
- interrupts = <48 2 0 0>;
- voltage-ranges = <3300 3300>;
- sdhci,auto-cmd12;
- clock-frequency = <0>;
- };
-
- i2c@118000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x118000 0x100>;
- interrupts = <38 2 0 0>;
- dfsrr;
- };
-
- i2c@118100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- compatible = "fsl-i2c";
- reg = <0x118100 0x100>;
- interrupts = <38 2 0 0>;
- dfsrr;
- };
-
- i2c@119000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <2>;
- compatible = "fsl-i2c";
- reg = <0x119000 0x100>;
- interrupts = <39 2 0 0>;
- dfsrr;
- };
-
- i2c@119100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <3>;
- compatible = "fsl-i2c";
- reg = <0x119100 0x100>;
- interrupts = <39 2 0 0>;
- dfsrr;
- };
-
- serial0: serial@11c500 {
- cell-index = <0>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x11c500 0x100>;
- clock-frequency = <0>;
- interrupts = <36 2 0 0>;
- };
-
- serial1: serial@11c600 {
- cell-index = <1>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x11c600 0x100>;
- clock-frequency = <0>;
- interrupts = <36 2 0 0>;
- };
-
- serial2: serial@11d500 {
- cell-index = <2>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x11d500 0x100>;
- clock-frequency = <0>;
- interrupts = <37 2 0 0>;
- };
-
- serial3: serial@11d600 {
- cell-index = <3>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x11d600 0x100>;
- clock-frequency = <0>;
- interrupts = <37 2 0 0>;
- };
-
- gpio0: gpio@130000 {
- compatible = "fsl,p4080-gpio", "fsl,qoriq-gpio";
- reg = <0x130000 0x1000>;
- interrupts = <55 2 0 0>;
- #gpio-cells = <2>;
- gpio-controller;
- };
-
- usb0: usb@210000 {
- compatible = "fsl,p4080-usb2-mph",
- "fsl,mpc85xx-usb2-mph", "fsl-usb2-mph";
- reg = <0x210000 0x1000>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <44 0x2 0 0>;
- };
-
- usb1: usb@211000 {
- compatible = "fsl,p4080-usb2-dr",
- "fsl,mpc85xx-usb2-dr", "fsl-usb2-dr";
- reg = <0x211000 0x1000>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <45 0x2 0 0>;
- };
-
- crypto: crypto@300000 {
- compatible = "fsl,sec-v4.0";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x300000 0x10000>;
- ranges = <0 0x300000 0x10000>;
- interrupt-parent = <&mpic>;
- interrupts = <92 2 0 0>;
-
- sec_jr0: jr@1000 {
- compatible = "fsl,sec-v4.0-job-ring";
- reg = <0x1000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <88 2 0 0>;
- };
-
- sec_jr1: jr@2000 {
- compatible = "fsl,sec-v4.0-job-ring";
- reg = <0x2000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <89 2 0 0>;
- };
-
- sec_jr2: jr@3000 {
- compatible = "fsl,sec-v4.0-job-ring";
- reg = <0x3000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <90 2 0 0>;
- };
-
- sec_jr3: jr@4000 {
- compatible = "fsl,sec-v4.0-job-ring";
- reg = <0x4000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <91 2 0 0>;
- };
-
- rtic@6000 {
- compatible = "fsl,sec-v4.0-rtic";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x6000 0x100>;
- ranges = <0x0 0x6100 0xe00>;
-
- rtic_a: rtic-a@0 {
- compatible = "fsl,sec-v4.0-rtic-memory";
- reg = <0x00 0x20 0x100 0x80>;
- };
-
- rtic_b: rtic-b@20 {
- compatible = "fsl,sec-v4.0-rtic-memory";
- reg = <0x20 0x20 0x200 0x80>;
- };
-
- rtic_c: rtic-c@40 {
- compatible = "fsl,sec-v4.0-rtic-memory";
- reg = <0x40 0x20 0x300 0x80>;
- };
-
- rtic_d: rtic-d@60 {
- compatible = "fsl,sec-v4.0-rtic-memory";
- reg = <0x60 0x20 0x500 0x80>;
- };
- };
- };
-
- sec_mon: sec_mon@314000 {
- compatible = "fsl,sec-v4.0-mon";
- reg = <0x314000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <93 2 0 0>;
- };
- };
-
- rapidio0: rapidio@ffe0c0000 {
- #address-cells = <2>;
- #size-cells = <2>;
- compatible = "fsl,rapidio-delta";
- interrupts = <
- 16 2 1 11 /* err_irq */
- 56 2 0 0 /* bell_outb_irq */
- 57 2 0 0 /* bell_inb_irq */
- 60 2 0 0 /* msg1_tx_irq */
- 61 2 0 0 /* msg1_rx_irq */
- 62 2 0 0 /* msg2_tx_irq */
- 63 2 0 0>; /* msg2_rx_irq */
- };
-
- localbus@ffe124000 {
- compatible = "fsl,p4080-elbc", "fsl,elbc", "simple-bus";
- interrupts = <25 2 0 0>;
- #address-cells = <2>;
- #size-cells = <1>;
- };
-
- pci0: pcie@ffe200000 {
- compatible = "fsl,p4080-pcie";
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
- bus-range = <0x0 0xff>;
- clock-frequency = <0x1fca055>;
- fsl,msi = <&msi0>;
- interrupts = <16 2 1 15>;
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupts = <16 2 1 15>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0 0 1 &mpic 40 1 0 0
- 0000 0 0 2 &mpic 1 1 0 0
- 0000 0 0 3 &mpic 2 1 0 0
- 0000 0 0 4 &mpic 3 1 0 0
- >;
- };
- };
-
- pci1: pcie@ffe201000 {
- compatible = "fsl,p4080-pcie";
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
- bus-range = <0 0xff>;
- clock-frequency = <0x1fca055>;
- fsl,msi = <&msi1>;
- interrupts = <16 2 1 14>;
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupts = <16 2 1 14>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0 0 1 &mpic 41 1 0 0
- 0000 0 0 2 &mpic 5 1 0 0
- 0000 0 0 3 &mpic 6 1 0 0
- 0000 0 0 4 &mpic 7 1 0 0
- >;
- };
- };
-
- pci2: pcie@ffe202000 {
- compatible = "fsl,p4080-pcie";
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
- bus-range = <0x0 0xff>;
- clock-frequency = <0x1fca055>;
- fsl,msi = <&msi2>;
- interrupts = <16 2 1 13>;
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupts = <16 2 1 13>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0 0 1 &mpic 42 1 0 0
- 0000 0 0 2 &mpic 9 1 0 0
- 0000 0 0 3 &mpic 10 1 0 0
- 0000 0 0 4 &mpic 11 1 0 0
- >;
- };
- };
-};
--
1.7.3.4
^ permalink raw reply related
* [PATCH 26/29] powerpc/85xx: Rework P3041DS device tree
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-25-git-send-email-galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p3041-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Fixed some dcsr compatiable typo's from 'p43041' to 'p3041'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/fsl/p3041si-post.dtsi | 332 ++++++++++++
arch/powerpc/boot/dts/fsl/p3041si-pre.dtsi | 112 ++++
arch/powerpc/boot/dts/p3041ds.dts | 12 +-
arch/powerpc/boot/dts/p3041si.dtsi | 729 ---------------------------
4 files changed, 454 insertions(+), 731 deletions(-)
create mode 100644 arch/powerpc/boot/dts/fsl/p3041si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/p3041si-pre.dtsi
delete mode 100644 arch/powerpc/boot/dts/p3041si.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/p3041si-post.dtsi b/arch/powerpc/boot/dts/fsl/p3041si-post.dtsi
new file mode 100644
index 0000000..9cda481
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p3041si-post.dtsi
@@ -0,0 +1,332 @@
+/*
+ * P3041 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ compatible = "fsl,p3041-elbc", "fsl,elbc", "simple-bus";
+ interrupts = <25 2 0 0>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+};
+
+/* controller at 0x200000 */
+&pci0 {
+ compatible = "fsl,p3041-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 1 15>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 15>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 40 1 0 0
+ 0000 0 0 2 &mpic 1 1 0 0
+ 0000 0 0 3 &mpic 2 1 0 0
+ 0000 0 0 4 &mpic 3 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x201000 */
+&pci1 {
+ compatible = "fsl,p3041-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 1 14>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 14>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 41 1 0 0
+ 0000 0 0 2 &mpic 5 1 0 0
+ 0000 0 0 3 &mpic 6 1 0 0
+ 0000 0 0 4 &mpic 7 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x202000 */
+&pci2 {
+ compatible = "fsl,p3041-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 1 13>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 13>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 42 1 0 0
+ 0000 0 0 2 &mpic 9 1 0 0
+ 0000 0 0 3 &mpic 10 1 0 0
+ 0000 0 0 4 &mpic 11 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x203000 */
+&pci3 {
+ compatible = "fsl,p3041-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 1 12>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 12>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 43 1 0 0
+ 0000 0 0 2 &mpic 0 1 0 0
+ 0000 0 0 3 &mpic 4 1 0 0
+ 0000 0 0 4 &mpic 8 1 0 0
+ >;
+ };
+};
+
+&dcsr {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,dcsr", "simple-bus";
+
+ dcsr-epu@0 {
+ compatible = "fsl,dcsr-epu";
+ interrupts = <52 2 0 0
+ 84 2 0 0
+ 85 2 0 0>;
+ reg = <0x0 0x1000>;
+ };
+ dcsr-npc {
+ compatible = "fsl,dcsr-npc";
+ reg = <0x1000 0x1000 0x1000000 0x8000>;
+ };
+ dcsr-nxc@2000 {
+ compatible = "fsl,dcsr-nxc";
+ reg = <0x2000 0x1000>;
+ };
+ dcsr-corenet {
+ compatible = "fsl,dcsr-corenet";
+ reg = <0x8000 0x1000 0xB0000 0x1000>;
+ };
+ dcsr-dpaa@9000 {
+ compatible = "fsl,p3041-dcsr-dpaa", "fsl,dcsr-dpaa";
+ reg = <0x9000 0x1000>;
+ };
+ dcsr-ocn@11000 {
+ compatible = "fsl,p3041-dcsr-ocn", "fsl,dcsr-ocn";
+ reg = <0x11000 0x1000>;
+ };
+ dcsr-ddr@12000 {
+ compatible = "fsl,dcsr-ddr";
+ dev-handle = <&ddr1>;
+ reg = <0x12000 0x1000>;
+ };
+ dcsr-nal@18000 {
+ compatible = "fsl,p3041-dcsr-nal", "fsl,dcsr-nal";
+ reg = <0x18000 0x1000>;
+ };
+ dcsr-rcpm@22000 {
+ compatible = "fsl,p3041-dcsr-rcpm", "fsl,dcsr-rcpm";
+ reg = <0x22000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@40000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu0>;
+ reg = <0x40000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@41000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu1>;
+ reg = <0x41000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@42000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu2>;
+ reg = <0x42000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@43000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu3>;
+ reg = <0x43000 0x1000>;
+ };
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "simple-bus";
+
+ soc-sram-error {
+ compatible = "fsl,soc-sram-error";
+ interrupts = <16 2 1 29>;
+ };
+
+ corenet-law@0 {
+ compatible = "fsl,corenet-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <32>;
+ };
+
+ ddr1: memory-controller@8000 {
+ compatible = "fsl,qoriq-memory-controller-v4.5", "fsl,qoriq-memory-controller";
+ reg = <0x8000 0x1000>;
+ interrupts = <16 2 1 23>;
+ };
+
+ cpc: l3-cache-controller@10000 {
+ compatible = "fsl,p3041-l3-cache-controller", "fsl,p4080-l3-cache-controller", "cache";
+ reg = <0x10000 0x1000>;
+ interrupts = <16 2 1 27>;
+ };
+
+ corenet-cf@18000 {
+ compatible = "fsl,corenet-cf";
+ reg = <0x18000 0x1000>;
+ interrupts = <16 2 1 31>;
+ fsl,ccf-num-csdids = <32>;
+ fsl,ccf-num-snoopids = <32>;
+ };
+
+ iommu@20000 {
+ compatible = "fsl,pamu-v1.0", "fsl,pamu";
+ reg = <0x20000 0x4000>;
+ interrupts = <
+ 24 2 0 0
+ 16 2 1 30>;
+ };
+
+/include/ "qoriq-mpic.dtsi"
+
+ guts: global-utilities@e0000 {
+ compatible = "fsl,qoriq-device-config-1.0";
+ reg = <0xe0000 0xe00>;
+ fsl,has-rstcr;
+ #sleep-cells = <1>;
+ fsl,liodn-bits = <12>;
+ };
+
+ pins: global-utilities@e0e00 {
+ compatible = "fsl,qoriq-pin-control-1.0";
+ reg = <0xe0e00 0x200>;
+ #sleep-cells = <2>;
+ };
+
+ clockgen: global-utilities@e1000 {
+ compatible = "fsl,p3041-clockgen", "fsl,qoriq-clockgen-1.0";
+ reg = <0xe1000 0x1000>;
+ clock-frequency = <0>;
+ };
+
+ rcpm: global-utilities@e2000 {
+ compatible = "fsl,qoriq-rcpm-1.0";
+ reg = <0xe2000 0x1000>;
+ #sleep-cells = <1>;
+ };
+
+ sfp: sfp@e8000 {
+ compatible = "fsl,p3041-sfp", "fsl,qoriq-sfp-1.0";
+ reg = <0xe8000 0x1000>;
+ };
+
+ serdes: serdes@ea000 {
+ compatible = "fsl,p3041-serdes";
+ reg = <0xea000 0x1000>;
+ };
+
+/include/ "qoriq-dma-0.dtsi"
+/include/ "qoriq-dma-1.dtsi"
+/include/ "qoriq-espi-0.dtsi"
+ spi@110000 {
+ fsl,espi-num-chipselects = <4>;
+ };
+
+/include/ "qoriq-esdhc-0.dtsi"
+ sdhc@114000 {
+ sdhci,auto-cmd12;
+ };
+
+/include/ "qoriq-i2c-0.dtsi"
+/include/ "qoriq-i2c-1.dtsi"
+/include/ "qoriq-duart-0.dtsi"
+/include/ "qoriq-duart-1.dtsi"
+/include/ "qoriq-gpio-0.dtsi"
+/include/ "qoriq-usb2-mph-0.dtsi"
+ usb0: usb@210000 {
+ phy_type = "utmi";
+ port0;
+ };
+
+/include/ "qoriq-usb2-dr-0.dtsi"
+ usb1: usb@211000 {
+ dr_mode = "host";
+ phy_type = "utmi";
+ };
+
+/include/ "qoriq-sata2-0.dtsi"
+/include/ "qoriq-sata2-1.dtsi"
+/include/ "qoriq-sec4.2-0.dtsi"
+};
diff --git a/arch/powerpc/boot/dts/fsl/p3041si-pre.dtsi b/arch/powerpc/boot/dts/fsl/p3041si-pre.dtsi
new file mode 100644
index 0000000..136def3
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p3041si-pre.dtsi
@@ -0,0 +1,112 @@
+/*
+ * P3041 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+ compatible = "fsl,P3041";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ ccsr = &soc;
+ dcsr = &dcsr;
+
+ serial0 = &serial0;
+ serial1 = &serial1;
+ serial2 = &serial2;
+ serial3 = &serial3;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
+ pci3 = &pci3;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ dma0 = &dma0;
+ dma1 = &dma1;
+ sdhc = &sdhc;
+ msi0 = &msi0;
+ msi1 = &msi1;
+ msi2 = &msi2;
+
+ crypto = &crypto;
+ sec_jr0 = &sec_jr0;
+ sec_jr1 = &sec_jr1;
+ sec_jr2 = &sec_jr2;
+ sec_jr3 = &sec_jr3;
+ rtic_a = &rtic_a;
+ rtic_b = &rtic_b;
+ rtic_c = &rtic_c;
+ rtic_d = &rtic_d;
+ sec_mon = &sec_mon;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: PowerPC,e500mc@0 {
+ device_type = "cpu";
+ reg = <0>;
+ next-level-cache = <&L2_0>;
+ L2_0: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu1: PowerPC,e500mc@1 {
+ device_type = "cpu";
+ reg = <1>;
+ next-level-cache = <&L2_1>;
+ L2_1: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu2: PowerPC,e500mc@2 {
+ device_type = "cpu";
+ reg = <2>;
+ next-level-cache = <&L2_2>;
+ L2_2: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu3: PowerPC,e500mc@3 {
+ device_type = "cpu";
+ reg = <3>;
+ next-level-cache = <&L2_3>;
+ L2_3: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p3041ds.dts b/arch/powerpc/boot/dts/p3041ds.dts
index bbd113b..1053d69 100644
--- a/arch/powerpc/boot/dts/p3041ds.dts
+++ b/arch/powerpc/boot/dts/p3041ds.dts
@@ -32,7 +32,7 @@
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
-/include/ "p3041si.dtsi"
+/include/ "fsl/p3041si-pre.dtsi"
/ {
model = "fsl,P3041DS";
@@ -50,6 +50,8 @@
};
soc: soc@ffe000000 {
+ ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+ reg = <0xf 0xfe000000 0 0x00001000>;
spi@110000 {
flash@0 {
#address-cells = <1>;
@@ -99,7 +101,7 @@
};
};
- localbus@ffe124000 {
+ lbc: localbus@ffe124000 {
reg = <0xf 0xfe124000 0 0x1000>;
ranges = <0 0 0xf 0xe8000000 0x08000000
2 0 0xf 0xffa00000 0x00040000
@@ -160,6 +162,7 @@
reg = <0xf 0xfe200000 0 0x1000>;
ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0x0 0x20000000
0x01000000 0 0x00000000 0xf 0xf8000000 0x0 0x00010000>;
+ fsl,msi = <&msi0>;
pcie@0 {
ranges = <0x02000000 0 0xe0000000
0x02000000 0 0xe0000000
@@ -175,6 +178,7 @@
reg = <0xf 0xfe201000 0 0x1000>;
ranges = <0x02000000 0x0 0xe0000000 0xc 0x20000000 0x0 0x20000000
0x01000000 0x0 0x00000000 0xf 0xf8010000 0x0 0x00010000>;
+ fsl,msi = <&msi1>;
pcie@0 {
ranges = <0x02000000 0 0xe0000000
0x02000000 0 0xe0000000
@@ -190,6 +194,7 @@
reg = <0xf 0xfe202000 0 0x1000>;
ranges = <0x02000000 0 0xe0000000 0xc 0x40000000 0 0x20000000
0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+ fsl,msi = <&msi2>;
pcie@0 {
ranges = <0x02000000 0 0xe0000000
0x02000000 0 0xe0000000
@@ -205,6 +210,7 @@
reg = <0xf 0xfe203000 0 0x1000>;
ranges = <0x02000000 0 0xe0000000 0xc 0x60000000 0 0x20000000
0x01000000 0 0x00000000 0xf 0xf8030000 0 0x00010000>;
+ fsl,msi = <&msi2>;
pcie@0 {
ranges = <0x02000000 0 0xe0000000
0x02000000 0 0xe0000000
@@ -216,3 +222,5 @@
};
};
};
+
+/include/ "fsl/p3041si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p3041si.dtsi b/arch/powerpc/boot/dts/p3041si.dtsi
deleted file mode 100644
index 87130b7..0000000
--- a/arch/powerpc/boot/dts/p3041si.dtsi
+++ /dev/null
@@ -1,729 +0,0 @@
-/*
- * P3041 Silicon Device Tree Source
- *
- * Copyright 2010-2011 Freescale Semiconductor Inc.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- * * Redistributions of source code must retain the above copyright
- * notice, this list of conditions and the following disclaimer.
- * * Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- * * Neither the name of Freescale Semiconductor nor the
- * names of its contributors may be used to endorse or promote products
- * derived from this software without specific prior written permission.
- *
- *
- * ALTERNATIVELY, this software may be distributed under the terms of the
- * GNU General Public License ("GPL") as published by the Free Software
- * Foundation, either version 2 of that License or (at your option) any
- * later version.
- *
- * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
- * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
- * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
- * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
- * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
- * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
- * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- */
-
-/dts-v1/;
-
-/ {
- compatible = "fsl,P3041";
- #address-cells = <2>;
- #size-cells = <2>;
- interrupt-parent = <&mpic>;
-
- aliases {
- ccsr = &soc;
- dcsr = &dcsr;
-
- serial0 = &serial0;
- serial1 = &serial1;
- serial2 = &serial2;
- serial3 = &serial3;
- pci0 = &pci0;
- pci1 = &pci1;
- pci2 = &pci2;
- pci3 = &pci3;
- usb0 = &usb0;
- usb1 = &usb1;
- dma0 = &dma0;
- dma1 = &dma1;
- sdhc = &sdhc;
- msi0 = &msi0;
- msi1 = &msi1;
- msi2 = &msi2;
-
- crypto = &crypto;
- sec_jr0 = &sec_jr0;
- sec_jr1 = &sec_jr1;
- sec_jr2 = &sec_jr2;
- sec_jr3 = &sec_jr3;
- rtic_a = &rtic_a;
- rtic_b = &rtic_b;
- rtic_c = &rtic_c;
- rtic_d = &rtic_d;
- sec_mon = &sec_mon;
-
-/*
- rio0 = &rapidio0;
- */
- };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu0: PowerPC,e500mc@0 {
- device_type = "cpu";
- reg = <0>;
- next-level-cache = <&L2_0>;
- L2_0: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- cpu1: PowerPC,e500mc@1 {
- device_type = "cpu";
- reg = <1>;
- next-level-cache = <&L2_1>;
- L2_1: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- cpu2: PowerPC,e500mc@2 {
- device_type = "cpu";
- reg = <2>;
- next-level-cache = <&L2_2>;
- L2_2: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- cpu3: PowerPC,e500mc@3 {
- device_type = "cpu";
- reg = <3>;
- next-level-cache = <&L2_3>;
- L2_3: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- };
-
- dcsr: dcsr@f00000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,dcsr", "simple-bus";
-
- dcsr-epu@0 {
- compatible = "fsl,dcsr-epu";
- interrupts = <52 2 0 0
- 84 2 0 0
- 85 2 0 0>;
- interrupt-parent = <&mpic>;
- reg = <0x0 0x1000>;
- };
- dcsr-npc {
- compatible = "fsl,dcsr-npc";
- reg = <0x1000 0x1000 0x1000000 0x8000>;
- };
- dcsr-nxc@2000 {
- compatible = "fsl,dcsr-nxc";
- reg = <0x2000 0x1000>;
- };
- dcsr-corenet {
- compatible = "fsl,dcsr-corenet";
- reg = <0x8000 0x1000 0xB0000 0x1000>;
- };
- dcsr-dpaa@9000 {
- compatible = "fsl,p43041-dcsr-dpaa", "fsl,dcsr-dpaa";
- reg = <0x9000 0x1000>;
- };
- dcsr-ocn@11000 {
- compatible = "fsl,p43041-dcsr-ocn", "fsl,dcsr-ocn";
- reg = <0x11000 0x1000>;
- };
- dcsr-ddr@12000 {
- compatible = "fsl,dcsr-ddr";
- dev-handle = <&ddr>;
- reg = <0x12000 0x1000>;
- };
- dcsr-nal@18000 {
- compatible = "fsl,p43041-dcsr-nal", "fsl,dcsr-nal";
- reg = <0x18000 0x1000>;
- };
- dcsr-rcpm@22000 {
- compatible = "fsl,p43041-dcsr-rcpm", "fsl,dcsr-rcpm";
- reg = <0x22000 0x1000>;
- };
- dcsr-cpu-sb-proxy@40000 {
- compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu0>;
- reg = <0x40000 0x1000>;
- };
- dcsr-cpu-sb-proxy@41000 {
- compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu1>;
- reg = <0x41000 0x1000>;
- };
- dcsr-cpu-sb-proxy@42000 {
- compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu2>;
- reg = <0x42000 0x1000>;
- };
- dcsr-cpu-sb-proxy@43000 {
- compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu3>;
- reg = <0x43000 0x1000>;
- };
- };
-
- soc: soc@ffe000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "soc";
- compatible = "simple-bus";
- ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
- reg = <0xf 0xfe000000 0 0x00001000>;
-
- soc-sram-error {
- compatible = "fsl,soc-sram-error";
- interrupts = <16 2 1 29>;
- };
-
- corenet-law@0 {
- compatible = "fsl,corenet-law";
- reg = <0x0 0x1000>;
- fsl,num-laws = <32>;
- };
-
- ddr: memory-controller@8000 {
- compatible = "fsl,qoriq-memory-controller-v4.5", "fsl,qoriq-memory-controller";
- reg = <0x8000 0x1000>;
- interrupts = <16 2 1 23>;
- };
-
- cpc: l3-cache-controller@10000 {
- compatible = "fsl,p3041-l3-cache-controller", "fsl,p4080-l3-cache-controller", "cache";
- reg = <0x10000 0x1000>;
- interrupts = <16 2 1 27>;
- };
-
- corenet-cf@18000 {
- compatible = "fsl,corenet-cf";
- reg = <0x18000 0x1000>;
- interrupts = <16 2 1 31>;
- fsl,ccf-num-csdids = <32>;
- fsl,ccf-num-snoopids = <32>;
- };
-
- iommu@20000 {
- compatible = "fsl,pamu-v1.0", "fsl,pamu";
- reg = <0x20000 0x4000>;
- interrupts = <
- 24 2 0 0
- 16 2 1 30>;
- };
-
- mpic: pic@40000 {
- clock-frequency = <0>;
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <4>;
- reg = <0x40000 0x40000>;
- compatible = "fsl,mpic", "chrp,open-pic";
- device_type = "open-pic";
- };
-
- msi0: msi@41600 {
- compatible = "fsl,mpic-msi";
- reg = <0x41600 0x200>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe0 0 0 0
- 0xe1 0 0 0
- 0xe2 0 0 0
- 0xe3 0 0 0
- 0xe4 0 0 0
- 0xe5 0 0 0
- 0xe6 0 0 0
- 0xe7 0 0 0>;
- };
-
- msi1: msi@41800 {
- compatible = "fsl,mpic-msi";
- reg = <0x41800 0x200>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe8 0 0 0
- 0xe9 0 0 0
- 0xea 0 0 0
- 0xeb 0 0 0
- 0xec 0 0 0
- 0xed 0 0 0
- 0xee 0 0 0
- 0xef 0 0 0>;
- };
-
- msi2: msi@41a00 {
- compatible = "fsl,mpic-msi";
- reg = <0x41a00 0x200>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xf0 0 0 0
- 0xf1 0 0 0
- 0xf2 0 0 0
- 0xf3 0 0 0
- 0xf4 0 0 0
- 0xf5 0 0 0
- 0xf6 0 0 0
- 0xf7 0 0 0>;
- };
-
- guts: global-utilities@e0000 {
- compatible = "fsl,qoriq-device-config-1.0";
- reg = <0xe0000 0xe00>;
- fsl,has-rstcr;
- #sleep-cells = <1>;
- fsl,liodn-bits = <12>;
- };
-
- pins: global-utilities@e0e00 {
- compatible = "fsl,qoriq-pin-control-1.0";
- reg = <0xe0e00 0x200>;
- #sleep-cells = <2>;
- };
-
- clockgen: global-utilities@e1000 {
- compatible = "fsl,p3041-clockgen", "fsl,qoriq-clockgen-1.0";
- reg = <0xe1000 0x1000>;
- clock-frequency = <0>;
- };
-
- rcpm: global-utilities@e2000 {
- compatible = "fsl,qoriq-rcpm-1.0";
- reg = <0xe2000 0x1000>;
- #sleep-cells = <1>;
- };
-
- sfp: sfp@e8000 {
- compatible = "fsl,p3041-sfp", "fsl,qoriq-sfp-1.0";
- reg = <0xe8000 0x1000>;
- };
-
- serdes: serdes@ea000 {
- compatible = "fsl,p3041-serdes";
- reg = <0xea000 0x1000>;
- };
-
- dma0: dma@100300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,p3041-dma", "fsl,eloplus-dma";
- reg = <0x100300 0x4>;
- ranges = <0x0 0x100100 0x200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,p3041-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupts = <28 2 0 0>;
- };
- dma-channel@80 {
- compatible = "fsl,p3041-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupts = <29 2 0 0>;
- };
- dma-channel@100 {
- compatible = "fsl,p3041-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupts = <30 2 0 0>;
- };
- dma-channel@180 {
- compatible = "fsl,p3041-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupts = <31 2 0 0>;
- };
- };
-
- dma1: dma@101300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,p3041-dma", "fsl,eloplus-dma";
- reg = <0x101300 0x4>;
- ranges = <0x0 0x101100 0x200>;
- cell-index = <1>;
- dma-channel@0 {
- compatible = "fsl,p3041-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupts = <32 2 0 0>;
- };
- dma-channel@80 {
- compatible = "fsl,p3041-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupts = <33 2 0 0>;
- };
- dma-channel@100 {
- compatible = "fsl,p3041-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupts = <34 2 0 0>;
- };
- dma-channel@180 {
- compatible = "fsl,p3041-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupts = <35 2 0 0>;
- };
- };
-
- spi@110000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,p3041-espi", "fsl,mpc8536-espi";
- reg = <0x110000 0x1000>;
- interrupts = <53 0x2 0 0>;
- fsl,espi-num-chipselects = <4>;
- };
-
- sdhc: sdhc@114000 {
- compatible = "fsl,p3041-esdhc", "fsl,esdhc";
- reg = <0x114000 0x1000>;
- interrupts = <48 2 0 0>;
- sdhci,auto-cmd12;
- clock-frequency = <0>;
- };
-
- i2c@118000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x118000 0x100>;
- interrupts = <38 2 0 0>;
- dfsrr;
- };
-
- i2c@118100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- compatible = "fsl-i2c";
- reg = <0x118100 0x100>;
- interrupts = <38 2 0 0>;
- dfsrr;
- };
-
- i2c@119000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <2>;
- compatible = "fsl-i2c";
- reg = <0x119000 0x100>;
- interrupts = <39 2 0 0>;
- dfsrr;
- };
-
- i2c@119100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <3>;
- compatible = "fsl-i2c";
- reg = <0x119100 0x100>;
- interrupts = <39 2 0 0>;
- dfsrr;
- };
-
- serial0: serial@11c500 {
- cell-index = <0>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x11c500 0x100>;
- clock-frequency = <0>;
- interrupts = <36 2 0 0>;
- };
-
- serial1: serial@11c600 {
- cell-index = <1>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x11c600 0x100>;
- clock-frequency = <0>;
- interrupts = <36 2 0 0>;
- };
-
- serial2: serial@11d500 {
- cell-index = <2>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x11d500 0x100>;
- clock-frequency = <0>;
- interrupts = <37 2 0 0>;
- };
-
- serial3: serial@11d600 {
- cell-index = <3>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x11d600 0x100>;
- clock-frequency = <0>;
- interrupts = <37 2 0 0>;
- };
-
- gpio0: gpio@130000 {
- compatible = "fsl,p3041-gpio", "fsl,qoriq-gpio";
- reg = <0x130000 0x1000>;
- interrupts = <55 2 0 0>;
- #gpio-cells = <2>;
- gpio-controller;
- };
-
- usb0: usb@210000 {
- compatible = "fsl,p3041-usb2-mph",
- "fsl,mpc85xx-usb2-mph", "fsl-usb2-mph";
- reg = <0x210000 0x1000>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <44 0x2 0 0>;
- phy_type = "utmi";
- port0;
- };
-
- usb1: usb@211000 {
- compatible = "fsl,p3041-usb2-dr",
- "fsl,mpc85xx-usb2-dr", "fsl-usb2-dr";
- reg = <0x211000 0x1000>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <45 0x2 0 0>;
- dr_mode = "host";
- phy_type = "utmi";
- };
-
- sata@220000 {
- compatible = "fsl,p3041-sata", "fsl,pq-sata-v2";
- reg = <0x220000 0x1000>;
- interrupts = <68 0x2 0 0>;
- };
-
- sata@221000 {
- compatible = "fsl,p3041-sata", "fsl,pq-sata-v2";
- reg = <0x221000 0x1000>;
- interrupts = <69 0x2 0 0>;
- };
-
- crypto: crypto@300000 {
- compatible = "fsl,sec-v4.2", "fsl,sec-v4.0";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x300000 0x10000>;
- ranges = <0 0x300000 0x10000>;
- interrupts = <92 2 0 0>;
-
- sec_jr0: jr@1000 {
- compatible = "fsl,sec-v4.2-job-ring",
- "fsl,sec-v4.0-job-ring";
- reg = <0x1000 0x1000>;
- interrupts = <88 2 0 0>;
- };
-
- sec_jr1: jr@2000 {
- compatible = "fsl,sec-v4.2-job-ring",
- "fsl,sec-v4.0-job-ring";
- reg = <0x2000 0x1000>;
- interrupts = <89 2 0 0>;
- };
-
- sec_jr2: jr@3000 {
- compatible = "fsl,sec-v4.2-job-ring",
- "fsl,sec-v4.0-job-ring";
- reg = <0x3000 0x1000>;
- interrupts = <90 2 0 0>;
- };
-
- sec_jr3: jr@4000 {
- compatible = "fsl,sec-v4.2-job-ring",
- "fsl,sec-v4.0-job-ring";
- reg = <0x4000 0x1000>;
- interrupts = <91 2 0 0>;
- };
-
- rtic@6000 {
- compatible = "fsl,sec-v4.2-rtic",
- "fsl,sec-v4.0-rtic";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x6000 0x100>;
- ranges = <0x0 0x6100 0xe00>;
-
- rtic_a: rtic-a@0 {
- compatible = "fsl,sec-v4.2-rtic-memory",
- "fsl,sec-v4.0-rtic-memory";
- reg = <0x00 0x20 0x100 0x80>;
- };
-
- rtic_b: rtic-b@20 {
- compatible = "fsl,sec-v4.2-rtic-memory",
- "fsl,sec-v4.0-rtic-memory";
- reg = <0x20 0x20 0x200 0x80>;
- };
-
- rtic_c: rtic-c@40 {
- compatible = "fsl,sec-v4.2-rtic-memory",
- "fsl,sec-v4.0-rtic-memory";
- reg = <0x40 0x20 0x300 0x80>;
- };
-
- rtic_d: rtic-d@60 {
- compatible = "fsl,sec-v4.2-rtic-memory",
- "fsl,sec-v4.0-rtic-memory";
- reg = <0x60 0x20 0x500 0x80>;
- };
- };
- };
-
- sec_mon: sec_mon@314000 {
- compatible = "fsl,sec-v4.2-mon", "fsl,sec-v4.0-mon";
- reg = <0x314000 0x1000>;
- interrupts = <93 2 0 0>;
- };
- };
-
-/*
- rapidio0: rapidio@ffe0c0000
-*/
-
- localbus@ffe124000 {
- compatible = "fsl,p3041-elbc", "fsl,elbc", "simple-bus";
- interrupts = <25 2 0 0>;
- #address-cells = <2>;
- #size-cells = <1>;
- };
-
- pci0: pcie@ffe200000 {
- compatible = "fsl,p3041-pcie", "fsl,qoriq-pcie-v2.2";
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
- bus-range = <0x0 0xff>;
- clock-frequency = <0x1fca055>;
- fsl,msi = <&msi0>;
- interrupts = <16 2 1 15>;
-
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupts = <16 2 1 15>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0 0 1 &mpic 40 1 0 0
- 0000 0 0 2 &mpic 1 1 0 0
- 0000 0 0 3 &mpic 2 1 0 0
- 0000 0 0 4 &mpic 3 1 0 0
- >;
- };
- };
-
- pci1: pcie@ffe201000 {
- compatible = "fsl,p3041-pcie", "fsl,qoriq-pcie-v2.2";
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
- bus-range = <0 0xff>;
- clock-frequency = <0x1fca055>;
- fsl,msi = <&msi1>;
- interrupts = <16 2 1 14>;
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupts = <16 2 1 14>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0 0 1 &mpic 41 1 0 0
- 0000 0 0 2 &mpic 5 1 0 0
- 0000 0 0 3 &mpic 6 1 0 0
- 0000 0 0 4 &mpic 7 1 0 0
- >;
- };
- };
-
- pci2: pcie@ffe202000 {
- compatible = "fsl,p3041-pcie", "fsl,qoriq-pcie-v2.2";
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
- bus-range = <0x0 0xff>;
- clock-frequency = <0x1fca055>;
- fsl,msi = <&msi2>;
- interrupts = <16 2 1 13>;
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupts = <16 2 1 13>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0 0 1 &mpic 42 1 0 0
- 0000 0 0 2 &mpic 9 1 0 0
- 0000 0 0 3 &mpic 10 1 0 0
- 0000 0 0 4 &mpic 11 1 0 0
- >;
- };
- };
-
- pci3: pcie@ffe203000 {
- compatible = "fsl,p3041-pcie", "fsl,qoriq-pcie-v2.2";
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
- bus-range = <0x0 0xff>;
- clock-frequency = <0x1fca055>;
- fsl,msi = <&msi2>;
- interrupts = <16 2 1 12>;
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupts = <16 2 1 12>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0 0 1 &mpic 43 1 0 0
- 0000 0 0 2 &mpic 0 1 0 0
- 0000 0 0 3 &mpic 4 1 0 0
- 0000 0 0 4 &mpic 8 1 0 0
- >;
- };
- };
-};
--
1.7.3.4
^ permalink raw reply related
* [PATCH 27/29] powerpc/85xx: Rework P3060QDS device tree
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-26-git-send-email-galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p3060-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
* Fixed l3-cache IRQs, we have 2 CPCs, so we should have IRQs for both
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/fsl/p3060si-post.dtsi | 296 +++++++++++
arch/powerpc/boot/dts/fsl/p3060si-pre.dtsi | 125 +++++
arch/powerpc/boot/dts/p3060qds.dts | 12 +-
arch/powerpc/boot/dts/p3060si.dtsi | 719 ---------------------------
4 files changed, 430 insertions(+), 722 deletions(-)
create mode 100644 arch/powerpc/boot/dts/fsl/p3060si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/p3060si-pre.dtsi
delete mode 100644 arch/powerpc/boot/dts/p3060si.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/p3060si-post.dtsi b/arch/powerpc/boot/dts/fsl/p3060si-post.dtsi
new file mode 100644
index 0000000..a63edd1
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p3060si-post.dtsi
@@ -0,0 +1,296 @@
+/*
+ * P3060 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ compatible = "fsl,p3060-elbc", "fsl,elbc", "simple-bus";
+ interrupts = <25 2 0 0>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+};
+
+/* controller at 0x200000 */
+&pci0 {
+ compatible = "fsl,p3060-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 1 15>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 15>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 40 1 0 0
+ 0000 0 0 2 &mpic 1 1 0 0
+ 0000 0 0 3 &mpic 2 1 0 0
+ 0000 0 0 4 &mpic 3 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x201000 */
+&pci1 {
+ compatible = "fsl,p3060-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 1 14>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 14>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 41 1 0 0
+ 0000 0 0 2 &mpic 5 1 0 0
+ 0000 0 0 3 &mpic 6 1 0 0
+ 0000 0 0 4 &mpic 7 1 0 0
+ >;
+ };
+};
+
+&rio {
+ compatible = "fsl,srio";
+ interrupts = <16 2 1 11>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ fsl,srio-rmu-handle = <&rmu>;
+ ranges;
+
+ port1 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ cell-index = <1>;
+ };
+
+ port2 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ cell-index = <2>;
+ };
+};
+
+&dcsr {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,dcsr", "simple-bus";
+
+ dcsr-epu@0 {
+ compatible = "fsl,dcsr-epu";
+ interrupts = <52 2 0 0
+ 84 2 0 0
+ 85 2 0 0>;
+ reg = <0x0 0x1000>;
+ };
+ dcsr-npc {
+ compatible = "fsl,dcsr-npc";
+ reg = <0x1000 0x1000 0x1000000 0x8000>;
+ };
+ dcsr-nxc@2000 {
+ compatible = "fsl,dcsr-nxc";
+ reg = <0x2000 0x1000>;
+ };
+ dcsr-corenet {
+ compatible = "fsl,dcsr-corenet";
+ reg = <0x8000 0x1000 0xB0000 0x1000>;
+ };
+ dcsr-dpaa@9000 {
+ compatible = "fsl,p3060-dcsr-dpaa", "fsl,dcsr-dpaa";
+ reg = <0x9000 0x1000>;
+ };
+ dcsr-ocn@11000 {
+ compatible = "fsl,p3060-dcsr-ocn", "fsl,dcsr-ocn";
+ reg = <0x11000 0x1000>;
+ };
+ dcsr-ddr@12000 {
+ compatible = "fsl,dcsr-ddr";
+ dev-handle = <&ddr1>;
+ reg = <0x12000 0x1000>;
+ };
+ dcsr-nal@18000 {
+ compatible = "fsl,p3060-dcsr-nal", "fsl,dcsr-nal";
+ reg = <0x18000 0x1000>;
+ };
+ dcsr-rcpm@22000 {
+ compatible = "fsl,p3060-dcsr-rcpm", "fsl,dcsr-rcpm";
+ reg = <0x22000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@40000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu0>;
+ reg = <0x40000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@41000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu1>;
+ reg = <0x41000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@44000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu4>;
+ reg = <0x44000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@45000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu5>;
+ reg = <0x45000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@46000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu6>;
+ reg = <0x46000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@47000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu7>;
+ reg = <0x47000 0x1000>;
+ };
+
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "simple-bus";
+
+ soc-sram-error {
+ compatible = "fsl,soc-sram-error";
+ interrupts = <16 2 1 29>;
+ };
+
+ corenet-law@0 {
+ compatible = "fsl,corenet-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <32>;
+ };
+
+ ddr1: memory-controller@8000 {
+ compatible = "fsl,qoriq-memory-controller-v4.4", "fsl,qoriq-memory-controller";
+ reg = <0x8000 0x1000>;
+ interrupts = <16 2 1 23>;
+ };
+
+ cpc: l3-cache-controller@10000 {
+ compatible = "fsl,p3060-l3-cache-controller", "cache";
+ reg = <0x10000 0x1000
+ 0x11000 0x1000>;
+ interrupts = <16 2 1 27
+ 16 2 1 26>;
+ };
+
+ corenet-cf@18000 {
+ compatible = "fsl,corenet-cf";
+ reg = <0x18000 0x1000>;
+ interrupts = <16 2 1 31>;
+ fsl,ccf-num-csdids = <32>;
+ fsl,ccf-num-snoopids = <32>;
+ };
+
+ iommu@20000 {
+ compatible = "fsl,pamu-v1.0", "fsl,pamu";
+ reg = <0x20000 0x5000>;
+ interrupts = <
+ 24 2 0 0
+ 16 2 1 30>;
+ };
+
+/include/ "qoriq-rmu-0.dtsi"
+/include/ "qoriq-mpic.dtsi"
+
+ guts: global-utilities@e0000 {
+ compatible = "fsl,qoriq-device-config-1.0";
+ reg = <0xe0000 0xe00>;
+ fsl,has-rstcr;
+ #sleep-cells = <1>;
+ fsl,liodn-bits = <12>;
+ };
+
+ pins: global-utilities@e0e00 {
+ compatible = "fsl,qoriq-pin-control-1.0";
+ reg = <0xe0e00 0x200>;
+ #sleep-cells = <2>;
+ };
+
+ clockgen: global-utilities@e1000 {
+ compatible = "fsl,p3060-clockgen", "fsl,qoriq-clockgen-1.0";
+ reg = <0xe1000 0x1000>;
+ clock-frequency = <0>;
+ };
+
+ rcpm: global-utilities@e2000 {
+ compatible = "fsl,qoriq-rcpm-1.0";
+ reg = <0xe2000 0x1000>;
+ #sleep-cells = <1>;
+ };
+
+ sfp: sfp@e8000 {
+ compatible = "fsl,p3060-sfp", "fsl,qoriq-sfp-1.0";
+ reg = <0xe8000 0x1000>;
+ };
+
+ serdes: serdes@ea000 {
+ compatible = "fsl,p3060-serdes";
+ reg = <0xea000 0x1000>;
+ };
+
+/include/ "qoriq-dma-0.dtsi"
+/include/ "qoriq-dma-1.dtsi"
+/include/ "qoriq-espi-0.dtsi"
+ spi@110000 {
+ fsl,espi-num-chipselects = <4>;
+ };
+
+/include/ "qoriq-i2c-0.dtsi"
+/include/ "qoriq-i2c-1.dtsi"
+/include/ "qoriq-duart-0.dtsi"
+/include/ "qoriq-duart-1.dtsi"
+/include/ "qoriq-gpio-0.dtsi"
+/include/ "qoriq-usb2-mph-0.dtsi"
+/include/ "qoriq-usb2-dr-0.dtsi"
+/include/ "qoriq-sec4.1-0.dtsi"
+};
diff --git a/arch/powerpc/boot/dts/fsl/p3060si-pre.dtsi b/arch/powerpc/boot/dts/fsl/p3060si-pre.dtsi
new file mode 100644
index 0000000..00c8e70
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p3060si-pre.dtsi
@@ -0,0 +1,125 @@
+/*
+ * P3060 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+ compatible = "fsl,P3060";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ ccsr = &soc;
+ dcsr = &dcsr;
+
+ serial0 = &serial0;
+ serial1 = &serial1;
+ serial2 = &serial2;
+ serial3 = &serial3;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ dma0 = &dma0;
+ dma1 = &dma1;
+ msi0 = &msi0;
+ msi1 = &msi1;
+ msi2 = &msi2;
+
+ crypto = &crypto;
+ sec_jr0 = &sec_jr0;
+ sec_jr1 = &sec_jr1;
+ sec_jr2 = &sec_jr2;
+ sec_jr3 = &sec_jr3;
+ rtic_a = &rtic_a;
+ rtic_b = &rtic_b;
+ rtic_c = &rtic_c;
+ rtic_d = &rtic_d;
+ sec_mon = &sec_mon;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: PowerPC,e500mc@0 {
+ device_type = "cpu";
+ reg = <0>;
+ next-level-cache = <&L2_0>;
+ L2_0: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu1: PowerPC,e500mc@1 {
+ device_type = "cpu";
+ reg = <1>;
+ next-level-cache = <&L2_1>;
+ L2_1: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu4: PowerPC,e500mc@4 {
+ device_type = "cpu";
+ reg = <4>;
+ next-level-cache = <&L2_4>;
+ L2_4: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu5: PowerPC,e500mc@5 {
+ device_type = "cpu";
+ reg = <5>;
+ next-level-cache = <&L2_5>;
+ L2_5: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu6: PowerPC,e500mc@6 {
+ device_type = "cpu";
+ reg = <6>;
+ next-level-cache = <&L2_6>;
+ L2_6: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu7: PowerPC,e500mc@7 {
+ device_type = "cpu";
+ reg = <7>;
+ next-level-cache = <&L2_7>;
+ L2_7: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p3060qds.dts b/arch/powerpc/boot/dts/p3060qds.dts
index 08b9193..529042e 100644
--- a/arch/powerpc/boot/dts/p3060qds.dts
+++ b/arch/powerpc/boot/dts/p3060qds.dts
@@ -32,7 +32,7 @@
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
-/include/ "p3060si.dtsi"
+/include/ "fsl/p3060si-pre.dtsi"
/ {
model = "fsl,P3060QDS";
@@ -50,6 +50,8 @@
};
soc: soc@ffe000000 {
+ ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+ reg = <0xf 0xfe000000 0 0x00001000>;
spi@110000 {
flash@0 {
#address-cells = <1>;
@@ -138,7 +140,7 @@
};
};
- rapidio@ffe0c0000 {
+ rio: rapidio@ffe0c0000 {
reg = <0xf 0xfe0c0000 0 0x11000>;
port1 {
@@ -149,7 +151,7 @@
};
};
- localbus@ffe124000 {
+ lbc: localbus@ffe124000 {
reg = <0xf 0xfe124000 0 0x1000>;
ranges = <0 0 0xf 0xe8000000 0x08000000
2 0 0xf 0xffa00000 0x00040000
@@ -210,6 +212,7 @@
reg = <0xf 0xfe200000 0 0x1000>;
ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0x0 0x20000000
0x01000000 0 0x00000000 0xf 0xf8000000 0x0 0x00010000>;
+ fsl,msi = <&msi0>;
pcie@0 {
ranges = <0x02000000 0 0xe0000000
0x02000000 0 0xe0000000
@@ -225,6 +228,7 @@
reg = <0xf 0xfe201000 0 0x1000>;
ranges = <0x02000000 0x0 0xe0000000 0xc 0x20000000 0x0 0x20000000
0x01000000 0x0 0x00000000 0xf 0xf8010000 0x0 0x00010000>;
+ fsl,msi = <&msi1>;
pcie@0 {
ranges = <0x02000000 0 0xe0000000
0x02000000 0 0xe0000000
@@ -236,3 +240,5 @@
};
};
};
+
+/include/ "fsl/p3060si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p3060si.dtsi b/arch/powerpc/boot/dts/p3060si.dtsi
deleted file mode 100644
index 68947e1..0000000
--- a/arch/powerpc/boot/dts/p3060si.dtsi
+++ /dev/null
@@ -1,719 +0,0 @@
-/*
- * P3060 Silicon Device Tree Source
- *
- * Copyright 2011 Freescale Semiconductor Inc.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- * * Redistributions of source code must retain the above copyright
- * notice, this list of conditions and the following disclaimer.
- * * Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- * * Neither the name of Freescale Semiconductor nor the
- * names of its contributors may be used to endorse or promote products
- * derived from this software without specific prior written permission.
- *
- *
- * ALTERNATIVELY, this software may be distributed under the terms of the
- * GNU General Public License ("GPL") as published by the Free Software
- * Foundation, either version 2 of that License or (at your option) any
- * later version.
- *
- * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
- * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
- * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
- * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
- * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
- * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
- * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- */
-
-/dts-v1/;
-
-/ {
- compatible = "fsl,P3060";
- #address-cells = <2>;
- #size-cells = <2>;
- interrupt-parent = <&mpic>;
-
- aliases {
- ccsr = &soc;
- dcsr = &dcsr;
-
- serial0 = &serial0;
- serial1 = &serial1;
- serial2 = &serial2;
- serial3 = &serial3;
- pci0 = &pci0;
- pci1 = &pci1;
- usb0 = &usb0;
- usb1 = &usb1;
- dma0 = &dma0;
- dma1 = &dma1;
- msi0 = &msi0;
- msi1 = &msi1;
- msi2 = &msi2;
-
- crypto = &crypto;
- sec_jr0 = &sec_jr0;
- sec_jr1 = &sec_jr1;
- sec_jr2 = &sec_jr2;
- sec_jr3 = &sec_jr3;
- rtic_a = &rtic_a;
- rtic_b = &rtic_b;
- rtic_c = &rtic_c;
- rtic_d = &rtic_d;
- sec_mon = &sec_mon;
- };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu0: PowerPC,e500mc@0 {
- device_type = "cpu";
- reg = <0>;
- next-level-cache = <&L2_0>;
- L2_0: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- cpu1: PowerPC,e500mc@1 {
- device_type = "cpu";
- reg = <1>;
- next-level-cache = <&L2_1>;
- L2_1: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- cpu4: PowerPC,e500mc@4 {
- device_type = "cpu";
- reg = <4>;
- next-level-cache = <&L2_4>;
- L2_4: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- cpu5: PowerPC,e500mc@5 {
- device_type = "cpu";
- reg = <5>;
- next-level-cache = <&L2_5>;
- L2_5: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- cpu6: PowerPC,e500mc@6 {
- device_type = "cpu";
- reg = <6>;
- next-level-cache = <&L2_6>;
- L2_6: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- cpu7: PowerPC,e500mc@7 {
- device_type = "cpu";
- reg = <7>;
- next-level-cache = <&L2_7>;
- L2_7: l2-cache {
- next-level-cache = <&cpc>;
- };
- };
- };
-
- dcsr: dcsr@f00000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,dcsr", "simple-bus";
-
- dcsr-epu@0 {
- compatible = "fsl,dcsr-epu";
- interrupts = <52 2 0 0
- 84 2 0 0
- 85 2 0 0>;
- interrupt-parent = <&mpic>;
- reg = <0x0 0x1000>;
- };
- dcsr-npc {
- compatible = "fsl,dcsr-npc";
- reg = <0x1000 0x1000 0x1000000 0x8000>;
- };
- dcsr-nxc@2000 {
- compatible = "fsl,dcsr-nxc";
- reg = <0x2000 0x1000>;
- };
- dcsr-corenet {
- compatible = "fsl,dcsr-corenet";
- reg = <0x8000 0x1000 0xB0000 0x1000>;
- };
- dcsr-dpaa@9000 {
- compatible = "fsl,p3060-dcsr-dpaa", "fsl,dcsr-dpaa";
- reg = <0x9000 0x1000>;
- };
- dcsr-ocn@11000 {
- compatible = "fsl,p3060-dcsr-ocn", "fsl,dcsr-ocn";
- reg = <0x11000 0x1000>;
- };
- dcsr-ddr@12000 {
- compatible = "fsl,dcsr-ddr";
- dev-handle = <&ddr>;
- reg = <0x12000 0x1000>;
- };
- dcsr-nal@18000 {
- compatible = "fsl,p3060-dcsr-nal", "fsl,dcsr-nal";
- reg = <0x18000 0x1000>;
- };
- dcsr-rcpm@22000 {
- compatible = "fsl,p3060-dcsr-rcpm", "fsl,dcsr-rcpm";
- reg = <0x22000 0x1000>;
- };
- dcsr-cpu-sb-proxy@40000 {
- compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu0>;
- reg = <0x40000 0x1000>;
- };
- dcsr-cpu-sb-proxy@41000 {
- compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu1>;
- reg = <0x41000 0x1000>;
- };
- dcsr-cpu-sb-proxy@44000 {
- compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu4>;
- reg = <0x44000 0x1000>;
- };
- dcsr-cpu-sb-proxy@45000 {
- compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu5>;
- reg = <0x45000 0x1000>;
- };
- dcsr-cpu-sb-proxy@46000 {
- compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu6>;
- reg = <0x46000 0x1000>;
- };
- dcsr-cpu-sb-proxy@47000 {
- compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
- cpu-handle = <&cpu7>;
- reg = <0x47000 0x1000>;
- };
- };
-
- soc: soc@ffe000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "soc";
- compatible = "simple-bus";
- ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
- reg = <0xf 0xfe000000 0 0x00001000>;
-
- soc-sram-error {
- compatible = "fsl,soc-sram-error";
- interrupts = <16 2 1 29>;
- };
-
- corenet-law@0 {
- compatible = "fsl,corenet-law";
- reg = <0x0 0x1000>;
- fsl,num-laws = <32>;
- };
-
- ddr: memory-controller@8000 {
- compatible = "fsl,qoriq-memory-controller-v4.4", "fsl,qoriq-memory-controller";
- reg = <0x8000 0x1000>;
- interrupts = <16 2 1 23>;
- };
-
- cpc: l3-cache-controller@10000 {
- compatible = "fsl,p3060-l3-cache-controller", "cache";
- reg = <0x10000 0x1000
- 0x11000 0x1000>;
- interrupts = <16 2 1 27>;
- };
-
- corenet-cf@18000 {
- compatible = "fsl,corenet-cf";
- reg = <0x18000 0x1000>;
- interrupts = <16 2 1 31>;
- fsl,ccf-num-csdids = <32>;
- fsl,ccf-num-snoopids = <32>;
- };
-
- iommu@20000 {
- compatible = "fsl,pamu-v1.0", "fsl,pamu";
- reg = <0x20000 0x5000>;
- interrupts = <
- 24 2 0 0
- 16 2 1 30>;
- };
-
- mpic: pic@40000 {
- clock-frequency = <0>;
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <4>;
- reg = <0x40000 0x40000>;
- compatible = "fsl,mpic", "chrp,open-pic";
- device_type = "open-pic";
- };
-
- msi0: msi@41600 {
- compatible = "fsl,mpic-msi";
- reg = <0x41600 0x200>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe0 0 0 0
- 0xe1 0 0 0
- 0xe2 0 0 0
- 0xe3 0 0 0
- 0xe4 0 0 0
- 0xe5 0 0 0
- 0xe6 0 0 0
- 0xe7 0 0 0>;
- };
-
- msi1: msi@41800 {
- compatible = "fsl,mpic-msi";
- reg = <0x41800 0x200>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe8 0 0 0
- 0xe9 0 0 0
- 0xea 0 0 0
- 0xeb 0 0 0
- 0xec 0 0 0
- 0xed 0 0 0
- 0xee 0 0 0
- 0xef 0 0 0>;
- };
-
- msi2: msi@41a00 {
- compatible = "fsl,mpic-msi";
- reg = <0x41a00 0x200>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xf0 0 0 0
- 0xf1 0 0 0
- 0xf2 0 0 0
- 0xf3 0 0 0
- 0xf4 0 0 0
- 0xf5 0 0 0
- 0xf6 0 0 0
- 0xf7 0 0 0>;
- };
-
- rmu: rmu@d3000 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,srio-rmu";
- reg = <0xd3000 0x500>;
- ranges = <0x0 0xd3000 0x500>;
-
- message-unit@0 {
- compatible = "fsl,srio-msg-unit";
- reg = <0x0 0x100>;
- interrupts = <
- 60 2 0 0 /* msg1_tx_irq */
- 61 2 0 0>;/* msg1_rx_irq */
- };
- message-unit@100 {
- compatible = "fsl,srio-msg-unit";
- reg = <0x100 0x100>;
- interrupts = <
- 62 2 0 0 /* msg2_tx_irq */
- 63 2 0 0>;/* msg2_rx_irq */
- };
- doorbell-unit@400 {
- compatible = "fsl,srio-dbell-unit";
- reg = <0x400 0x80>;
- interrupts = <
- 56 2 0 0 /* bell_outb_irq */
- 57 2 0 0>;/* bell_inb_irq */
- };
- port-write-unit@4e0 {
- compatible = "fsl,srio-port-write-unit";
- reg = <0x4e0 0x20>;
- interrupts = <16 2 1 11>;
- };
- };
-
- guts: global-utilities@e0000 {
- compatible = "fsl,qoriq-device-config-1.0";
- reg = <0xe0000 0xe00>;
- fsl,has-rstcr;
- #sleep-cells = <1>;
- fsl,liodn-bits = <12>;
- };
-
- pins: global-utilities@e0e00 {
- compatible = "fsl,qoriq-pin-control-1.0";
- reg = <0xe0e00 0x200>;
- #sleep-cells = <2>;
- };
-
- clockgen: global-utilities@e1000 {
- compatible = "fsl,p3060-clockgen", "fsl,qoriq-clockgen-1.0";
- reg = <0xe1000 0x1000>;
- clock-frequency = <0>;
- };
-
- rcpm: global-utilities@e2000 {
- compatible = "fsl,qoriq-rcpm-1.0";
- reg = <0xe2000 0x1000>;
- #sleep-cells = <1>;
- };
-
- sfp: sfp@e8000 {
- compatible = "fsl,p3060-sfp", "fsl,qoriq-sfp-1.0";
- reg = <0xe8000 0x1000>;
- };
-
- serdes: serdes@ea000 {
- compatible = "fsl,p3060-serdes";
- reg = <0xea000 0x1000>;
- };
-
- dma0: dma@100300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,p3060-dma", "fsl,eloplus-dma";
- reg = <0x100300 0x4>;
- ranges = <0x0 0x100100 0x200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,p3060-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupts = <28 2 0 0>;
- };
- dma-channel@80 {
- compatible = "fsl,p3060-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupts = <29 2 0 0>;
- };
- dma-channel@100 {
- compatible = "fsl,p3060-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupts = <30 2 0 0>;
- };
- dma-channel@180 {
- compatible = "fsl,p3060-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupts = <31 2 0 0>;
- };
- };
-
- dma1: dma@101300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,p3060-dma", "fsl,eloplus-dma";
- reg = <0x101300 0x4>;
- ranges = <0x0 0x101100 0x200>;
- cell-index = <1>;
- dma-channel@0 {
- compatible = "fsl,p3060-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupts = <32 2 0 0>;
- };
- dma-channel@80 {
- compatible = "fsl,p3060-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupts = <33 2 0 0>;
- };
- dma-channel@100 {
- compatible = "fsl,p3060-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupts = <34 2 0 0>;
- };
- dma-channel@180 {
- compatible = "fsl,p3060-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupts = <35 2 0 0>;
- };
- };
-
- spi@110000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,p3060-espi", "fsl,mpc8536-espi";
- reg = <0x110000 0x1000>;
- interrupts = <53 0x2 0 0>;
- fsl,espi-num-chipselects = <4>;
- };
-
- i2c@118000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x118000 0x100>;
- interrupts = <38 2 0 0>;
- dfsrr;
- };
-
- i2c@118100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- compatible = "fsl-i2c";
- reg = <0x118100 0x100>;
- interrupts = <38 2 0 0>;
- dfsrr;
- };
-
- i2c@119000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <2>;
- compatible = "fsl-i2c";
- reg = <0x119000 0x100>;
- interrupts = <39 2 0 0>;
- dfsrr;
- };
-
- i2c@119100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <3>;
- compatible = "fsl-i2c";
- reg = <0x119100 0x100>;
- interrupts = <39 2 0 0>;
- dfsrr;
- };
-
- serial0: serial@11c500 {
- cell-index = <0>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x11c500 0x100>;
- clock-frequency = <0>;
- interrupts = <36 2 0 0>;
- };
-
- serial1: serial@11c600 {
- cell-index = <1>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x11c600 0x100>;
- clock-frequency = <0>;
- interrupts = <36 2 0 0>;
- };
-
- serial2: serial@11d500 {
- cell-index = <2>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x11d500 0x100>;
- clock-frequency = <0>;
- interrupts = <37 2 0 0>;
- };
-
- serial3: serial@11d600 {
- cell-index = <3>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x11d600 0x100>;
- clock-frequency = <0>;
- interrupts = <37 2 0 0>;
- };
-
- gpio0: gpio@130000 {
- compatible = "fsl,p3060-gpio", "fsl,qoriq-gpio";
- reg = <0x130000 0x1000>;
- interrupts = <55 2 0 0>;
- #gpio-cells = <2>;
- gpio-controller;
- };
-
- usb0: usb@210000 {
- compatible = "fsl,p3060-usb2-mph",
- "fsl,mpc85xx-usb2-mph", "fsl-usb2-mph";
- reg = <0x210000 0x1000>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <44 0x2 0 0>;
- };
-
- usb1: usb@211000 {
- compatible = "fsl,p3060-usb2-dr",
- "fsl,mpc85xx-usb2-dr", "fsl-usb2-dr";
- reg = <0x211000 0x1000>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <45 0x2 0 0>;
- };
-
- crypto: crypto@300000 {
- compatible = "fsl,sec-v4.1", "fsl,sec-v4.0";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x300000 0x10000>;
- ranges = <0 0x300000 0x10000>;
- interrupt-parent = <&mpic>;
- interrupts = <92 2 0 0>;
-
- sec_jr0: jr@1000 {
- compatible = "fsl,sec-v4.1-job-ring", "fsl,sec-v4.0-job-ring";
- reg = <0x1000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <88 2 0 0>;
- };
-
- sec_jr1: jr@2000 {
- compatible = "fsl,sec-v4.1-job-ring", "fsl,sec-v4.0-job-ring";
- reg = <0x2000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <89 2 0 0>;
- };
-
- sec_jr2: jr@3000 {
- compatible = "fsl,sec-v4.1-job-ring", "fsl,sec-v4.0-job-ring";
- reg = <0x3000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <90 2 0 0>;
- };
-
- sec_jr3: jr@4000 {
- compatible = "fsl,sec-v4.1-job-ring", "fsl,sec-v4.0-job-ring";
- reg = <0x4000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <91 2 0 0>;
- };
-
- rtic@6000 {
- compatible = "fsl,sec-v4.1-rtic", "fsl,sec-v4.0-rtic";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x6000 0x100>;
- ranges = <0x0 0x6100 0xe00>;
-
- rtic_a: rtic-a@0 {
- compatible = "fsl,sec-v4.1-rtic-memory", "fsl,sec-v4.0-rtic-memory";
- reg = <0x00 0x20 0x100 0x80>;
- };
-
- rtic_b: rtic-b@20 {
- compatible = "fsl,sec-v4.1-rtic-memory", "fsl,sec-v4.0-rtic-memory";
- reg = <0x20 0x20 0x200 0x80>;
- };
-
- rtic_c: rtic-c@40 {
- compatible = "fsl,sec-v4.1-rtic-memory", "fsl,sec-v4.0-rtic-memory";
- reg = <0x40 0x20 0x300 0x80>;
- };
-
- rtic_d: rtic-d@60 {
- compatible = "fsl,sec-v4.1-rtic-memory", "fsl,sec-v4.0-rtic-memory";
- reg = <0x60 0x20 0x500 0x80>;
- };
- };
- };
-
- sec_mon: sec_mon@314000 {
- compatible = "fsl,sec-v4.1-mon", "fsl,sec-v4.0-mon";
- reg = <0x314000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <93 2 0 0>;
- };
- };
-
- rapidio@ffe0c0000 {
- compatible = "fsl,srio";
- interrupts = <16 2 1 11>;
- #address-cells = <2>;
- #size-cells = <2>;
- fsl,srio-rmu-handle = <&rmu>;
- ranges;
-
- port1 {
- #address-cells = <2>;
- #size-cells = <2>;
- cell-index = <1>;
- };
-
- port2 {
- #address-cells = <2>;
- #size-cells = <2>;
- cell-index = <2>;
- };
- };
-
- localbus@ffe124000 {
- compatible = "fsl,p3060-elbc", "fsl,elbc", "simple-bus";
- interrupts = <25 2 0 0>;
- #address-cells = <2>;
- #size-cells = <1>;
- };
-
- pci0: pcie@ffe200000 {
- compatible = "fsl,p3060-pcie", "fsl,qoriq-pcie-v2.2";
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
- bus-range = <0x0 0xff>;
- clock-frequency = <33333333>;
- fsl,msi = <&msi0>;
- interrupts = <16 2 1 15>;
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupts = <16 2 1 15>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0 0 1 &mpic 40 1 0 0
- 0000 0 0 2 &mpic 1 1 0 0
- 0000 0 0 3 &mpic 2 1 0 0
- 0000 0 0 4 &mpic 3 1 0 0
- >;
- };
- };
-
- pci1: pcie@ffe201000 {
- compatible = "fsl,p3060-pcie", "fsl,qoriq-pcie-v2.2";
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
- bus-range = <0 0xff>;
- clock-frequency = <33333333>;
- fsl,msi = <&msi1>;
- interrupts = <16 2 1 14>;
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupts = <16 2 1 14>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0 0 1 &mpic 41 1 0 0
- 0000 0 0 2 &mpic 5 1 0 0
- 0000 0 0 3 &mpic 6 1 0 0
- 0000 0 0 4 &mpic 7 1 0 0
- >;
- };
- };
-};
--
1.7.3.4
^ permalink raw reply related
* [PATCH 25/29] powerpc/85xx: Rework P2041RDB device tree
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-24-git-send-email-galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p2041-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/fsl/p2041si-post.dtsi | 305 +++++++++++++++++++++++++++
arch/powerpc/boot/dts/fsl/p2041si-pre.dtsi | 111 ++++++++++
arch/powerpc/boot/dts/p2041rdb.dts | 11 +-
3 files changed, 425 insertions(+), 2 deletions(-)
create mode 100644 arch/powerpc/boot/dts/fsl/p2041si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/p2041si-pre.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/p2041si-post.dtsi b/arch/powerpc/boot/dts/fsl/p2041si-post.dtsi
new file mode 100644
index 0000000..8d037cf
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p2041si-post.dtsi
@@ -0,0 +1,305 @@
+/*
+ * P2041/P2040 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ compatible = "fsl,p2041-elbc", "fsl,elbc", "simple-bus";
+ interrupts = <25 2 0 0>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+};
+
+/* controller at 0x200000 */
+&pci0 {
+ compatible = "fsl,p2041-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 1 15>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 15>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 40 1 0 0
+ 0000 0 0 2 &mpic 1 1 0 0
+ 0000 0 0 3 &mpic 2 1 0 0
+ 0000 0 0 4 &mpic 3 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x201000 */
+&pci1 {
+ compatible = "fsl,p2041-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 1 14>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 14>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 41 1 0 0
+ 0000 0 0 2 &mpic 5 1 0 0
+ 0000 0 0 3 &mpic 6 1 0 0
+ 0000 0 0 4 &mpic 7 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x202000 */
+&pci2 {
+ compatible = "fsl,p2041-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 1 13>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 13>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 42 1 0 0
+ 0000 0 0 2 &mpic 9 1 0 0
+ 0000 0 0 3 &mpic 10 1 0 0
+ 0000 0 0 4 &mpic 11 1 0 0
+ >;
+ };
+};
+
+&dcsr {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,dcsr", "simple-bus";
+
+ dcsr-epu@0 {
+ compatible = "fsl,dcsr-epu";
+ interrupts = <52 2 0 0
+ 84 2 0 0
+ 85 2 0 0>;
+ reg = <0x0 0x1000>;
+ };
+ dcsr-npc {
+ compatible = "fsl,dcsr-npc";
+ reg = <0x1000 0x1000 0x1000000 0x8000>;
+ };
+ dcsr-nxc@2000 {
+ compatible = "fsl,dcsr-nxc";
+ reg = <0x2000 0x1000>;
+ };
+ dcsr-corenet {
+ compatible = "fsl,dcsr-corenet";
+ reg = <0x8000 0x1000 0xB0000 0x1000>;
+ };
+ dcsr-dpaa@9000 {
+ compatible = "fsl,p2041-dcsr-dpaa", "fsl,dcsr-dpaa";
+ reg = <0x9000 0x1000>;
+ };
+ dcsr-ocn@11000 {
+ compatible = "fsl,p2041-dcsr-ocn", "fsl,dcsr-ocn";
+ reg = <0x11000 0x1000>;
+ };
+ dcsr-ddr@12000 {
+ compatible = "fsl,dcsr-ddr";
+ dev-handle = <&ddr1>;
+ reg = <0x12000 0x1000>;
+ };
+ dcsr-nal@18000 {
+ compatible = "fsl,p2041-dcsr-nal", "fsl,dcsr-nal";
+ reg = <0x18000 0x1000>;
+ };
+ dcsr-rcpm@22000 {
+ compatible = "fsl,p2041-dcsr-rcpm", "fsl,dcsr-rcpm";
+ reg = <0x22000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@40000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu0>;
+ reg = <0x40000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@41000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu1>;
+ reg = <0x41000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@42000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu2>;
+ reg = <0x42000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@43000 {
+ compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu3>;
+ reg = <0x43000 0x1000>;
+ };
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "simple-bus";
+
+ soc-sram-error {
+ compatible = "fsl,soc-sram-error";
+ interrupts = <16 2 1 29>;
+ };
+
+ corenet-law@0 {
+ compatible = "fsl,corenet-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <32>;
+ };
+
+ ddr1: memory-controller@8000 {
+ compatible = "fsl,qoriq-memory-controller-v4.5", "fsl,qoriq-memory-controller";
+ reg = <0x8000 0x1000>;
+ interrupts = <16 2 1 23>;
+ };
+
+ cpc: l3-cache-controller@10000 {
+ compatible = "fsl,p2041-l3-cache-controller", "fsl,p4080-l3-cache-controller", "cache";
+ reg = <0x10000 0x1000>;
+ interrupts = <16 2 1 27>;
+ };
+
+ corenet-cf@18000 {
+ compatible = "fsl,corenet-cf";
+ reg = <0x18000 0x1000>;
+ interrupts = <16 2 1 31>;
+ fsl,ccf-num-csdids = <32>;
+ fsl,ccf-num-snoopids = <32>;
+ };
+
+ iommu@20000 {
+ compatible = "fsl,pamu-v1.0", "fsl,pamu";
+ reg = <0x20000 0x4000>;
+ interrupts = <
+ 24 2 0 0
+ 16 2 1 30>;
+ };
+
+/include/ "qoriq-mpic.dtsi"
+
+ guts: global-utilities@e0000 {
+ compatible = "fsl,qoriq-device-config-1.0";
+ reg = <0xe0000 0xe00>;
+ fsl,has-rstcr;
+ #sleep-cells = <1>;
+ fsl,liodn-bits = <12>;
+ };
+
+ pins: global-utilities@e0e00 {
+ compatible = "fsl,qoriq-pin-control-1.0";
+ reg = <0xe0e00 0x200>;
+ #sleep-cells = <2>;
+ };
+
+ clockgen: global-utilities@e1000 {
+ compatible = "fsl,p2041-clockgen", "fsl,qoriq-clockgen-1.0";
+ reg = <0xe1000 0x1000>;
+ clock-frequency = <0>;
+ };
+
+ rcpm: global-utilities@e2000 {
+ compatible = "fsl,qoriq-rcpm-1.0";
+ reg = <0xe2000 0x1000>;
+ #sleep-cells = <1>;
+ };
+
+ sfp: sfp@e8000 {
+ compatible = "fsl,p2041-sfp", "fsl,qoriq-sfp-1.0";
+ reg = <0xe8000 0x1000>;
+ };
+
+ serdes: serdes@ea000 {
+ compatible = "fsl,p2041-serdes";
+ reg = <0xea000 0x1000>;
+ };
+
+/include/ "qoriq-dma-0.dtsi"
+/include/ "qoriq-dma-1.dtsi"
+/include/ "qoriq-espi-0.dtsi"
+ spi@110000 {
+ fsl,espi-num-chipselects = <4>;
+ };
+
+/include/ "qoriq-esdhc-0.dtsi"
+ sdhc@114000 {
+ sdhci,auto-cmd12;
+ };
+
+/include/ "qoriq-i2c-0.dtsi"
+/include/ "qoriq-i2c-1.dtsi"
+/include/ "qoriq-duart-0.dtsi"
+/include/ "qoriq-duart-1.dtsi"
+/include/ "qoriq-gpio-0.dtsi"
+/include/ "qoriq-usb2-mph-0.dtsi"
+ usb0: usb@210000 {
+ phy_type = "utmi";
+ port0;
+ };
+
+/include/ "qoriq-usb2-dr-0.dtsi"
+ usb1: usb@211000 {
+ dr_mode = "host";
+ phy_type = "utmi";
+ };
+
+/include/ "qoriq-sata2-0.dtsi"
+/include/ "qoriq-sata2-1.dtsi"
+/include/ "qoriq-sec4.2-0.dtsi"
+};
diff --git a/arch/powerpc/boot/dts/fsl/p2041si-pre.dtsi b/arch/powerpc/boot/dts/fsl/p2041si-pre.dtsi
new file mode 100644
index 0000000..2d0a40d
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p2041si-pre.dtsi
@@ -0,0 +1,111 @@
+/*
+ * P2041 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+ compatible = "fsl,P2041";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ ccsr = &soc;
+ dcsr = &dcsr;
+
+ serial0 = &serial0;
+ serial1 = &serial1;
+ serial2 = &serial2;
+ serial3 = &serial3;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ dma0 = &dma0;
+ dma1 = &dma1;
+ sdhc = &sdhc;
+ msi0 = &msi0;
+ msi1 = &msi1;
+ msi2 = &msi2;
+
+ crypto = &crypto;
+ sec_jr0 = &sec_jr0;
+ sec_jr1 = &sec_jr1;
+ sec_jr2 = &sec_jr2;
+ sec_jr3 = &sec_jr3;
+ rtic_a = &rtic_a;
+ rtic_b = &rtic_b;
+ rtic_c = &rtic_c;
+ rtic_d = &rtic_d;
+ sec_mon = &sec_mon;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: PowerPC,e500mc@0 {
+ device_type = "cpu";
+ reg = <0>;
+ next-level-cache = <&L2_0>;
+ L2_0: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu1: PowerPC,e500mc@1 {
+ device_type = "cpu";
+ reg = <1>;
+ next-level-cache = <&L2_1>;
+ L2_1: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu2: PowerPC,e500mc@2 {
+ device_type = "cpu";
+ reg = <2>;
+ next-level-cache = <&L2_2>;
+ L2_2: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu3: PowerPC,e500mc@3 {
+ device_type = "cpu";
+ reg = <3>;
+ next-level-cache = <&L2_3>;
+ L2_3: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p2041rdb.dts b/arch/powerpc/boot/dts/p2041rdb.dts
index 79b6895..d6ea24d 100644
--- a/arch/powerpc/boot/dts/p2041rdb.dts
+++ b/arch/powerpc/boot/dts/p2041rdb.dts
@@ -32,7 +32,7 @@
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
-/include/ "p2041si.dtsi"
+/include/ "fsl/p2041si-pre.dtsi"
/ {
model = "fsl,P2041RDB";
@@ -50,6 +50,8 @@
};
soc: soc@ffe000000 {
+ ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+ reg = <0xf 0xfe000000 0 0x00001000>;
spi@110000 {
flash@0 {
#address-cells = <1>;
@@ -106,7 +108,7 @@
};
};
- localbus@ffe124000 {
+ lbc: localbus@ffe124000 {
reg = <0xf 0xfe124000 0 0x1000>;
ranges = <0 0 0xf 0xe8000000 0x08000000>;
@@ -122,6 +124,7 @@
reg = <0xf 0xfe200000 0 0x1000>;
ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0x0 0x20000000
0x01000000 0 0x00000000 0xf 0xf8000000 0x0 0x00010000>;
+ fsl,msi = <&msi0>;
pcie@0 {
ranges = <0x02000000 0 0xe0000000
0x02000000 0 0xe0000000
@@ -137,6 +140,7 @@
reg = <0xf 0xfe201000 0 0x1000>;
ranges = <0x02000000 0x0 0xe0000000 0xc 0x20000000 0x0 0x20000000
0x01000000 0x0 0x00000000 0xf 0xf8010000 0x0 0x00010000>;
+ fsl,msi = <&msi1>;
pcie@0 {
ranges = <0x02000000 0 0xe0000000
0x02000000 0 0xe0000000
@@ -152,6 +156,7 @@
reg = <0xf 0xfe202000 0 0x1000>;
ranges = <0x02000000 0 0xe0000000 0xc 0x40000000 0 0x20000000
0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+ fsl,msi = <&msi2>;
pcie@0 {
ranges = <0x02000000 0 0xe0000000
0x02000000 0 0xe0000000
@@ -163,3 +168,5 @@
};
};
};
+
+/include/ "fsl/p2041si-post.dtsi"
--
1.7.3.4
^ permalink raw reply related
* [PATCH 24/29] powerpc/85xx: Rework P2020RDB device tree
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-23-git-send-email-galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
moved PCI device IRQs down to virtual bridge level
* Updated spi node to new espi binding specification
* Renamed 'sdhci' node to 'sdhc'
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Fixed wrong reg offsets for mdio nodes associated with etsec2 &
* etsec3
* Dropping "fsl,p2020-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/p2020rdb.dts | 63 ++---
arch/powerpc/boot/dts/p2020rdb_camp_core0.dts | 141 +----------
arch/powerpc/boot/dts/p2020rdb_camp_core1.dts | 107 +--------
arch/powerpc/boot/dts/p2020si.dtsi | 355 -------------------------
4 files changed, 22 insertions(+), 644 deletions(-)
delete mode 100644 arch/powerpc/boot/dts/p2020si.dtsi
diff --git a/arch/powerpc/boot/dts/p2020rdb.dts b/arch/powerpc/boot/dts/p2020rdb.dts
index 1d7a05f..fd42712 100644
--- a/arch/powerpc/boot/dts/p2020rdb.dts
+++ b/arch/powerpc/boot/dts/p2020rdb.dts
@@ -9,7 +9,7 @@
* option) any later version.
*/
-/include/ "p2020si.dtsi"
+/include/ "fsl/p2020si-pre.dtsi"
/ {
model = "fsl,P2020RDB";
@@ -29,7 +29,8 @@
device_type = "memory";
};
- localbus@ffe05000 {
+ lbc: localbus@ffe05000 {
+ reg = <0 0xffe05000 0 0x1000>;
/* NOR and NAND Flashes */
ranges = <0x0 0x0 0x0 0xef000000 0x01000000
@@ -140,7 +141,9 @@
};
- soc@ffe00000 {
+ soc: soc@ffe00000 {
+ ranges = <0x0 0x0 0xffe00000 0x100000>;
+
i2c@3000 {
rtc@68 {
compatible = "dallas,ds1339";
@@ -148,17 +151,13 @@
};
};
- spi@7000 {
-
- fsl_m25p80@0 {
+ spi@7000 {
+ flash@0 {
#address-cells = <1>;
#size-cells = <1>;
- compatible = "fsl,espi-flash";
+ compatible = "spansion,s25sl12801";
reg = <0>;
- linux,modalias = "fsl_m25p80";
- modal = "s25sl128b";
spi-max-frequency = <50000000>;
- mode = <0>;
partition@0 {
/* 512KB for u-boot Bootloader Image */
@@ -202,13 +201,11 @@
mdio@24520 {
phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <3 1>;
+ interrupts = <3 1 0 0>;
reg = <0x0>;
};
phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <3 1>;
+ interrupts = <3 1 0 0>;
reg = <0x1>;
};
};
@@ -224,11 +221,7 @@
status = "disabled";
};
- ptp_clock@24E00 {
- compatible = "fsl,etsec-ptp";
- reg = <0x24E00 0xB0>;
- interrupts = <68 2 69 2 70 2>;
- interrupt-parent = < &mpic >;
+ ptp_clock@24e00 {
fsl,tclk-period = <5>;
fsl,tmr-prsc = <200>;
fsl,tmr-add = <0xCCCCCCCD>;
@@ -252,29 +245,18 @@
phy-handle = <&phy1>;
phy-connection-type = "rgmii-id";
};
-
};
pci0: pcie@ffe08000 {
+ reg = <0 0xffe08000 0 0x1000>;
status = "disabled";
};
pci1: pcie@ffe09000 {
+ reg = <0 0xffe09000 0 0x1000>;
ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0x0 0x0 0x1 &mpic 0x4 0x1
- 0000 0x0 0x0 0x2 &mpic 0x5 0x1
- 0000 0x0 0x0 0x3 &mpic 0x6 0x1
- 0000 0x0 0x0 0x4 &mpic 0x7 0x1
- >;
- pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
+ pcie@0 {
ranges = <0x2000000 0x0 0xa0000000
0x2000000 0x0 0xa0000000
0x0 0x20000000
@@ -286,21 +268,10 @@
};
pci2: pcie@ffe0a000 {
+ reg = <0 0xffe0a000 0 0x1000>;
ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0x0 0x0 0x1 &mpic 0x0 0x1
- 0000 0x0 0x0 0x2 &mpic 0x1 0x1
- 0000 0x0 0x0 0x3 &mpic 0x2 0x1
- 0000 0x0 0x0 0x4 &mpic 0x3 0x1
- >;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
ranges = <0x2000000 0x0 0x80000000
0x2000000 0x0 0x80000000
0x0 0x20000000
@@ -311,3 +282,5 @@
};
};
};
+
+/include/ "fsl/p2020si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p2020rdb_camp_core0.dts b/arch/powerpc/boot/dts/p2020rdb_camp_core0.dts
index fc8dddd..66aac86 100644
--- a/arch/powerpc/boot/dts/p2020rdb_camp_core0.dts
+++ b/arch/powerpc/boot/dts/p2020rdb_camp_core0.dts
@@ -14,28 +14,16 @@
* option) any later version.
*/
-/include/ "p2020si.dtsi"
+/include/ "p2020rdb.dts"
/ {
model = "fsl,P2020RDB";
compatible = "fsl,P2020RDB", "fsl,MPC85XXRDB-CAMP";
- aliases {
- ethernet1 = &enet1;
- ethernet2 = &enet2;
- serial0 = &serial0;
- pci0 = &pci0;
- };
-
cpus {
PowerPC,P2020@1 {
- status = "disabled";
+ status = "disabled";
};
-
- };
-
- memory {
- device_type = "memory";
};
localbus@ffe05000 {
@@ -43,115 +31,18 @@
};
soc@ffe00000 {
- i2c@3000 {
- rtc@68 {
- compatible = "dallas,ds1339";
- reg = <0x68>;
- };
- };
-
serial1: serial@4600 {
status = "disabled";
};
- spi@7000 {
-
- fsl_m25p80@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,espi-flash";
- reg = <0>;
- linux,modalias = "fsl_m25p80";
- modal = "s25sl128b";
- spi-max-frequency = <50000000>;
- mode = <0>;
-
- partition@0 {
- /* 512KB for u-boot Bootloader Image */
- reg = <0x0 0x00080000>;
- label = "SPI (RO) U-Boot Image";
- read-only;
- };
-
- partition@80000 {
- /* 512KB for DTB Image */
- reg = <0x00080000 0x00080000>;
- label = "SPI (RO) DTB Image";
- read-only;
- };
-
- partition@100000 {
- /* 4MB for Linux Kernel Image */
- reg = <0x00100000 0x00400000>;
- label = "SPI (RO) Linux Kernel Image";
- read-only;
- };
-
- partition@500000 {
- /* 4MB for Compressed RFS Image */
- reg = <0x00500000 0x00400000>;
- label = "SPI (RO) Compressed RFS Image";
- read-only;
- };
-
- partition@900000 {
- /* 7MB for JFFS2 based RFS */
- reg = <0x00900000 0x00700000>;
- label = "SPI (RW) JFFS2 RFS";
- };
- };
- };
-
dma@c300 {
status = "disabled";
};
- usb@22000 {
- phy_type = "ulpi";
- };
-
- mdio@24520 {
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <3 1>;
- reg = <0x0>;
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <3 1>;
- reg = <0x1>;
- };
- };
-
- mdio@25520 {
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@26520 {
- status = "disabled";
- };
-
enet0: ethernet@24000 {
status = "disabled";
};
- enet1: ethernet@25000 {
- tbi-handle = <&tbi0>;
- phy-handle = <&phy0>;
- phy-connection-type = "sgmii";
-
- };
-
- enet2: ethernet@26000 {
- phy-handle = <&phy1>;
- phy-connection-type = "rgmii-id";
- };
-
-
mpic: pic@40000 {
protected-sources = <
42 76 77 78 79 /* serial1 , dma2 */
@@ -164,40 +55,12 @@
msi@41600 {
status = "disabled";
};
-
-
};
pci0: pcie@ffe08000 {
status = "disabled";
};
- pci1: pcie@ffe09000 {
- ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
- 0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0x0 0x0 0x1 &mpic 0x4 0x1
- 0000 0x0 0x0 0x2 &mpic 0x5 0x1
- 0000 0x0 0x0 0x3 &mpic 0x6 0x1
- 0000 0x0 0x0 0x4 &mpic 0x7 0x1
- >;
- pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- ranges = <0x2000000 0x0 0xa0000000
- 0x2000000 0x0 0xa0000000
- 0x0 0x20000000
-
- 0x1000000 0x0 0x0
- 0x1000000 0x0 0x0
- 0x0 0x100000>;
- };
- };
-
pci2: pcie@ffe0a000 {
status = "disabled";
};
diff --git a/arch/powerpc/boot/dts/p2020rdb_camp_core1.dts b/arch/powerpc/boot/dts/p2020rdb_camp_core1.dts
index 261c34b..9bd8ef4 100644
--- a/arch/powerpc/boot/dts/p2020rdb_camp_core1.dts
+++ b/arch/powerpc/boot/dts/p2020rdb_camp_core1.dts
@@ -15,28 +15,18 @@
* option) any later version.
*/
-/include/ "p2020si.dtsi"
+/include/ "p2020rdb.dts"
/ {
model = "fsl,P2020RDB";
compatible = "fsl,P2020RDB", "fsl,MPC85XXRDB-CAMP";
- aliases {
- ethernet0 = &enet0;
- serial0 = &serial1;
- pci1 = &pci1;
- };
-
cpus {
PowerPC,P2020@0 {
- status = "disabled";
+ status = "disabled";
};
};
- memory {
- device_type = "memory";
- };
-
localbus@ffe05000 {
status = "disabled";
};
@@ -70,55 +60,10 @@
status = "disabled";
};
- dma@c300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,eloplus-dma";
- reg = <0xc300 0x4>;
- ranges = <0x0 0xc100 0x200>;
- cell-index = <1>;
- dma-channel@0 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <76 2>;
- };
- dma-channel@80 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupt-parent = <&mpic>;
- interrupts = <77 2>;
- };
- dma-channel@100 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupt-parent = <&mpic>;
- interrupts = <78 2>;
- };
- dma-channel@180 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupt-parent = <&mpic>;
- interrupts = <79 2>;
- };
- };
-
gpio: gpio-controller@f000 {
status = "disabled";
};
- L2: l2-cache-controller@20000 {
- compatible = "fsl,p2020-l2-cache-controller";
- reg = <0x20000 0x1000>;
- cache-line-size = <32>; // 32 bytes
- cache-size = <0x80000>; // L2,512K
- interrupt-parent = <&mpic>;
- };
-
dma@21300 {
status = "disabled";
};
@@ -139,12 +84,6 @@
status = "disabled";
};
- enet0: ethernet@24000 {
- fixed-link = <1 1 1000 0 0>;
- phy-connection-type = "rgmii-id";
-
- };
-
enet1: ethernet@25000 {
status = "disabled";
};
@@ -170,22 +109,6 @@
>;
};
- msi@41600 {
- compatible = "fsl,p2020-msi", "fsl,mpic-msi";
- reg = <0x41600 0x80>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe0 0
- 0xe1 0
- 0xe2 0
- 0xe3 0
- 0xe4 0
- 0xe5 0
- 0xe6 0
- 0xe7 0>;
- interrupt-parent = <&mpic>;
- };
-
global-utilities@e0000 { //global utilities block
status = "disabled";
};
@@ -199,30 +122,4 @@
pci1: pcie@ffe09000 {
status = "disabled";
};
-
- pci2: pcie@ffe0a000 {
- ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
- 0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0x0 0x0 0x1 &mpic 0x0 0x1
- 0000 0x0 0x0 0x2 &mpic 0x1 0x1
- 0000 0x0 0x0 0x3 &mpic 0x2 0x1
- 0000 0x0 0x0 0x4 &mpic 0x3 0x1
- >;
- pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- ranges = <0x2000000 0x0 0x80000000
- 0x2000000 0x0 0x80000000
- 0x0 0x20000000
-
- 0x1000000 0x0 0x0
- 0x1000000 0x0 0x0
- 0x0 0x100000>;
- };
- };
};
diff --git a/arch/powerpc/boot/dts/p2020si.dtsi b/arch/powerpc/boot/dts/p2020si.dtsi
deleted file mode 100644
index 37f7194..0000000
--- a/arch/powerpc/boot/dts/p2020si.dtsi
+++ /dev/null
@@ -1,355 +0,0 @@
-/*
- * P2020 Device Tree Source
- *
- * Copyright 2011 Freescale Semiconductor Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-/dts-v1/;
-/ {
- compatible = "fsl,P2020";
- #address-cells = <2>;
- #size-cells = <2>;
- interrupt-parent = <&mpic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- PowerPC,P2020@0 {
- device_type = "cpu";
- reg = <0x0>;
- next-level-cache = <&L2>;
- };
-
- PowerPC,P2020@1 {
- device_type = "cpu";
- reg = <0x1>;
- next-level-cache = <&L2>;
- };
- };
-
- localbus@ffe05000 {
- #address-cells = <2>;
- #size-cells = <1>;
- compatible = "fsl,p2020-elbc", "fsl,elbc", "simple-bus";
- reg = <0 0xffe05000 0 0x1000>;
- interrupts = <19 2 0 0>;
- };
-
- soc@ffe00000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "soc";
- compatible = "fsl,p2020-immr", "simple-bus";
- ranges = <0x0 0x0 0xffe00000 0x100000>;
- bus-frequency = <0>; // Filled out by uboot.
-
- ecm-law@0 {
- compatible = "fsl,ecm-law";
- reg = <0x0 0x1000>;
- fsl,num-laws = <12>;
- };
-
- ecm@1000 {
- compatible = "fsl,p2020-ecm", "fsl,ecm";
- reg = <0x1000 0x1000>;
- interrupts = <17 2 0 0>;
- };
-
- memory-controller@2000 {
- compatible = "fsl,p2020-memory-controller";
- reg = <0x2000 0x1000>;
- interrupts = <18 2 0 0>;
- };
-
- i2c@3000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x3000 0x100>;
- interrupts = <43 2 0 0>;
- dfsrr;
- };
-
- i2c@3100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- compatible = "fsl-i2c";
- reg = <0x3100 0x100>;
- interrupts = <43 2 0 0>;
- dfsrr;
- };
-
- serial0: serial@4500 {
- cell-index = <0>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4500 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2 0 0>;
- };
-
- serial1: serial@4600 {
- cell-index = <1>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4600 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2 0 0>;
- };
-
- spi@7000 {
- cell-index = <0>;
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,espi";
- reg = <0x7000 0x1000>;
- interrupts = <59 0x2 0 0>;
- mode = "cpu";
- };
-
- dma@c300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,eloplus-dma";
- reg = <0xc300 0x4>;
- ranges = <0x0 0xc100 0x200>;
- cell-index = <1>;
- dma-channel@0 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupts = <76 2 0 0>;
- };
- dma-channel@80 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupts = <77 2 0 0>;
- };
- dma-channel@100 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupts = <78 2 0 0>;
- };
- dma-channel@180 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupts = <79 2 0 0>;
- };
- };
-
- gpio: gpio-controller@f000 {
- #gpio-cells = <2>;
- compatible = "fsl,mpc8572-gpio";
- reg = <0xf000 0x100>;
- interrupts = <47 0x2 0 0>;
- gpio-controller;
- };
-
- L2: l2-cache-controller@20000 {
- compatible = "fsl,p2020-l2-cache-controller";
- reg = <0x20000 0x1000>;
- cache-line-size = <32>; // 32 bytes
- cache-size = <0x80000>; // L2,512K
- interrupts = <16 2 0 0>;
- };
-
- dma@21300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,eloplus-dma";
- reg = <0x21300 0x4>;
- ranges = <0x0 0x21100 0x200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupts = <20 2 0 0>;
- };
- dma-channel@80 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupts = <21 2 0 0>;
- };
- dma-channel@100 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupts = <22 2 0 0>;
- };
- dma-channel@180 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupts = <23 2 0 0>;
- };
- };
-
- usb@22000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl-usb2-dr";
- reg = <0x22000 0x1000>;
- interrupts = <28 0x2 0 0>;
- };
-
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x26520 0x20>;
- };
-
- mdio@26520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x520 0x20>;
- };
-
- enet0: ethernet@24000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <0>;
- device_type = "network";
- model = "eTSEC";
- compatible = "gianfar";
- reg = <0x24000 0x1000>;
- ranges = <0x0 0x24000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <29 2 0 0 30 2 0 0 34 2 0 0>;
- };
-
- enet1: ethernet@25000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <1>;
- device_type = "network";
- model = "eTSEC";
- compatible = "gianfar";
- reg = <0x25000 0x1000>;
- ranges = <0x0 0x25000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <35 2 0 0 36 2 0 0 40 2 0 0>;
-
- };
-
- enet2: ethernet@26000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <2>;
- device_type = "network";
- model = "eTSEC";
- compatible = "gianfar";
- reg = <0x26000 0x1000>;
- ranges = <0x0 0x26000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <31 2 0 0 32 2 0 0 33 2 0 0>;
-
- };
-
- sdhci@2e000 {
- compatible = "fsl,p2020-esdhc", "fsl,esdhc";
- reg = <0x2e000 0x1000>;
- interrupts = <72 0x2 0 0>;
- /* Filled in by U-Boot */
- clock-frequency = <0>;
- };
-
- crypto@30000 {
- compatible = "fsl,sec3.1", "fsl,sec3.0", "fsl,sec2.4",
- "fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0";
- reg = <0x30000 0x10000>;
- interrupts = <45 2 0 0 58 2 0 0>;
- fsl,num-channels = <4>;
- fsl,channel-fifo-len = <24>;
- fsl,exec-units-mask = <0xbfe>;
- fsl,descriptor-types-mask = <0x3ab0ebf>;
- };
-
- mpic: pic@40000 {
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <2>;
- reg = <0x40000 0x40000>;
- compatible = "chrp,open-pic";
- device_type = "open-pic";
- };
-
- msi@41600 {
- compatible = "fsl,p2020-msi", "fsl,mpic-msi";
- reg = <0x41600 0x80>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe0 0 0 0
- 0xe1 0 0 0
- 0xe2 0 0 0
- 0xe3 0 0 0
- 0xe4 0 0 0
- 0xe5 0 0 0
- 0xe6 0 0 0
- 0xe7 0 0 0>;
- };
-
- global-utilities@e0000 { //global utilities block
- compatible = "fsl,p2020-guts";
- reg = <0xe0000 0x1000>;
- fsl,has-rstcr;
- };
- };
-
- pci0: pcie@ffe08000 {
- compatible = "fsl,mpc8548-pcie";
- device_type = "pci";
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- reg = <0 0xffe08000 0 0x1000>;
- bus-range = <0 255>;
- clock-frequency = <33333333>;
- interrupts = <24 2 0 0>;
- };
-
- pci1: pcie@ffe09000 {
- compatible = "fsl,mpc8548-pcie";
- device_type = "pci";
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- reg = <0 0xffe09000 0 0x1000>;
- bus-range = <0 255>;
- clock-frequency = <33333333>;
- interrupts = <25 2 0 0>;
- };
-
- pci2: pcie@ffe0a000 {
- compatible = "fsl,mpc8548-pcie";
- device_type = "pci";
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- reg = <0 0xffe0a000 0 0x1000>;
- bus-range = <0 255>;
- clock-frequency = <33333333>;
- interrupts = <26 2 0 0>;
- };
-};
--
1.7.3.4
^ permalink raw reply related
* [PATCH 23/29] powerpc/85xx: Rework P2020DS device tree
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-22-git-send-email-galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Updated spi node to new espi binding specification
* Renamed 'sdhci' node to 'sdhc'
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Fixed wrong reg offsets for mdio nodes associated with etsec2 & etsec3
* Dropping "fsl,p2020-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/fsl/p2020si-post.dtsi | 194 +++++++++++++++
arch/powerpc/boot/dts/fsl/p2020si-pre.dtsi | 69 ++++++
arch/powerpc/boot/dts/p2020ds.dts | 353 ++-------------------------
arch/powerpc/boot/dts/p2020ds.dtsi | 316 ++++++++++++++++++++++++
arch/powerpc/boot/dts/p2020si.dtsi | 99 +++-----
5 files changed, 634 insertions(+), 397 deletions(-)
create mode 100644 arch/powerpc/boot/dts/fsl/p2020si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/p2020si-pre.dtsi
create mode 100644 arch/powerpc/boot/dts/p2020ds.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/p2020si-post.dtsi b/arch/powerpc/boot/dts/fsl/p2020si-post.dtsi
new file mode 100644
index 0000000..c041050
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p2020si-post.dtsi
@@ -0,0 +1,194 @@
+/*
+ * P2020/P2010 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,p2020-elbc", "fsl,elbc", "simple-bus";
+ interrupts = <19 2 0 0>;
+};
+
+/* controller at 0xa000 */
+&pci0 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <26 2 0 0>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <26 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+ >;
+ };
+};
+
+/* controller at 0x9000 */
+&pci1 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <25 2 0 0>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <25 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x4 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x5 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0x6 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0x7 0x1 0x0 0x0
+ >;
+ };
+};
+
+/* controller at 0x8000 */
+&pci2 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <24 2 0 0>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <24 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x8 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x9 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0xa 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0xb 0x1 0x0 0x0
+ >;
+ };
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "fsl,p2020-immr", "simple-bus";
+ bus-frequency = <0>; // Filled out by uboot.
+
+ ecm-law@0 {
+ compatible = "fsl,ecm-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <12>;
+ };
+
+ ecm@1000 {
+ compatible = "fsl,p2020-ecm", "fsl,ecm";
+ reg = <0x1000 0x1000>;
+ interrupts = <17 2 0 0>;
+ };
+
+ memory-controller@2000 {
+ compatible = "fsl,p2020-memory-controller";
+ reg = <0x2000 0x1000>;
+ interrupts = <18 2 0 0>;
+ };
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-duart-0.dtsi"
+/include/ "pq3-espi-0.dtsi"
+ spi0: spi@7000 {
+ fsl,espi-num-chipselects = <4>;
+ };
+
+/include/ "pq3-dma-1.dtsi"
+/include/ "pq3-gpio-0.dtsi"
+
+ L2: l2-cache-controller@20000 {
+ compatible = "fsl,p2020-l2-cache-controller";
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x80000>; // L2,512K
+ interrupts = <16 2 0 0>;
+ };
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-usb2-dr-0.dtsi"
+/include/ "pq3-etsec1-0.dtsi"
+/include/ "pq3-etsec1-timer-0.dtsi"
+
+ ptp_clock@24e00 {
+ interrupts = <68 2 0 0 69 2 0 0 70 2 0 0>;
+ };
+
+
+/include/ "pq3-etsec1-1.dtsi"
+/include/ "pq3-etsec1-2.dtsi"
+/include/ "pq3-esdhc-0.dtsi"
+/include/ "pq3-sec3.1-0.dtsi"
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-mpic-timer-B.dtsi"
+
+ global-utilities@e0000 {
+ compatible = "fsl,p2020-guts";
+ reg = <0xe0000 0x1000>;
+ fsl,has-rstcr;
+ };
+};
diff --git a/arch/powerpc/boot/dts/fsl/p2020si-pre.dtsi b/arch/powerpc/boot/dts/fsl/p2020si-pre.dtsi
new file mode 100644
index 0000000..3213288
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p2020si-pre.dtsi
@@ -0,0 +1,69 @@
+/*
+ * P2020/P2010 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+ compatible = "fsl,P2020";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,P2020@0 {
+ device_type = "cpu";
+ reg = <0x0>;
+ next-level-cache = <&L2>;
+ };
+
+ PowerPC,P2020@1 {
+ device_type = "cpu";
+ reg = <0x1>;
+ next-level-cache = <&L2>;
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p2020ds.dts b/arch/powerpc/boot/dts/p2020ds.dts
index 66f03d6..237310c 100644
--- a/arch/powerpc/boot/dts/p2020ds.dts
+++ b/arch/powerpc/boot/dts/p2020ds.dts
@@ -9,30 +9,17 @@
* option) any later version.
*/
-/include/ "p2020si.dtsi"
+/include/ "fsl/p2020si-pre.dtsi"
/ {
model = "fsl,P2020DS";
compatible = "fsl,P2020DS";
- aliases {
- ethernet0 = &enet0;
- ethernet1 = &enet1;
- ethernet2 = &enet2;
- serial0 = &serial0;
- serial1 = &serial1;
- pci0 = &pci0;
- pci1 = &pci1;
- pci2 = &pci2;
- };
-
-
memory {
device_type = "memory";
};
- localbus@ffe05000 {
- compatible = "fsl,elbc", "simple-bus";
+ board_lbc: lbc: localbus@ffe05000 {
ranges = <0x0 0x0 0x0 0xe8000000 0x08000000
0x1 0x0 0x0 0xe0000000 0x08000000
0x2 0x0 0x0 0xffa00000 0x00040000
@@ -40,203 +27,18 @@
0x4 0x0 0x0 0xffa40000 0x00040000
0x5 0x0 0x0 0xffa80000 0x00040000
0x6 0x0 0x0 0xffac0000 0x00040000>;
-
- nor@0,0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "cfi-flash";
- reg = <0x0 0x0 0x8000000>;
- bank-width = <2>;
- device-width = <1>;
-
- ramdisk@0 {
- reg = <0x0 0x03000000>;
- read-only;
- };
-
- diagnostic@3000000 {
- reg = <0x03000000 0x00e00000>;
- read-only;
- };
-
- dink@3e00000 {
- reg = <0x03e00000 0x00200000>;
- read-only;
- };
-
- kernel@4000000 {
- reg = <0x04000000 0x00400000>;
- read-only;
- };
-
- jffs2@4400000 {
- reg = <0x04400000 0x03b00000>;
- };
-
- dtb@7f00000 {
- reg = <0x07f00000 0x00080000>;
- read-only;
- };
-
- u-boot@7f80000 {
- reg = <0x07f80000 0x00080000>;
- read-only;
- };
- };
-
- nand@2,0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,elbc-fcm-nand";
- reg = <0x2 0x0 0x40000>;
-
- u-boot@0 {
- reg = <0x0 0x02000000>;
- read-only;
- };
-
- jffs2@2000000 {
- reg = <0x02000000 0x10000000>;
- };
-
- ramdisk@12000000 {
- reg = <0x12000000 0x08000000>;
- read-only;
- };
-
- kernel@1a000000 {
- reg = <0x1a000000 0x04000000>;
- };
-
- dtb@1e000000 {
- reg = <0x1e000000 0x01000000>;
- read-only;
- };
-
- empty@1f000000 {
- reg = <0x1f000000 0x21000000>;
- };
- };
-
- board-control@3,0 {
- compatible = "fsl,p2020ds-fpga", "fsl,fpga-ngpixis";
- reg = <0x3 0x0 0x30>;
- };
-
- nand@4,0 {
- compatible = "fsl,elbc-fcm-nand";
- reg = <0x4 0x0 0x40000>;
- };
-
- nand@5,0 {
- compatible = "fsl,elbc-fcm-nand";
- reg = <0x5 0x0 0x40000>;
- };
-
- nand@6,0 {
- compatible = "fsl,elbc-fcm-nand";
- reg = <0x6 0x0 0x40000>;
- };
+ reg = <0 0xffe05000 0 0x1000>;
};
- soc@ffe00000 {
-
- usb@22000 {
- phy_type = "ulpi";
- };
-
- mdio@24520 {
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <3 1>;
- reg = <0x0>;
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <3 1>;
- reg = <0x1>;
- };
- phy2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- interrupts = <3 1>;
- reg = <0x2>;
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
-
- };
-
- mdio@25520 {
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@26520 {
- tbi2: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
-
- };
-
- ptp_clock@24E00 {
- compatible = "fsl,etsec-ptp";
- reg = <0x24E00 0xB0>;
- interrupts = <68 2 69 2 70 2>;
- interrupt-parent = < &mpic >;
- fsl,tclk-period = <5>;
- fsl,tmr-prsc = <200>;
- fsl,tmr-add = <0xCCCCCCCD>;
- fsl,tmr-fiper1 = <0x3B9AC9FB>;
- fsl,tmr-fiper2 = <0x0001869B>;
- fsl,max-adj = <249999999>;
- };
-
- enet0: ethernet@24000 {
- tbi-handle = <&tbi0>;
- phy-handle = <&phy0>;
- phy-connection-type = "rgmii-id";
- };
-
- enet1: ethernet@25000 {
- tbi-handle = <&tbi1>;
- phy-handle = <&phy1>;
- phy-connection-type = "rgmii-id";
-
- };
-
- enet2: ethernet@26000 {
- tbi-handle = <&tbi2>;
- phy-handle = <&phy2>;
- phy-connection-type = "rgmii-id";
- };
-
-
- msi@41600 {
- compatible = "fsl,mpic-msi";
- };
+ board_soc: soc: soc@ffe00000 {
+ ranges = <0x0 0x0 0xffe00000 0x100000>;
};
- pci0: pcie@ffe08000 {
+ pci2: pcie@ffe08000 {
ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0x0 0x0 0x1 &mpic 0x8 0x1
- 0000 0x0 0x0 0x2 &mpic 0x9 0x1
- 0000 0x0 0x0 0x3 &mpic 0xa 0x1
- 0000 0x0 0x0 0x4 &mpic 0xb 0x1
- >;
+ reg = <0 0xffe08000 0 0x1000>;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
ranges = <0x2000000 0x0 0x80000000
0x2000000 0x0 0x80000000
0x0 0x20000000
@@ -247,61 +49,11 @@
};
};
- pci1: pcie@ffe09000 {
+ board_pci1: pci1: pcie@ffe09000 {
ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
- interrupt-map-mask = <0xff00 0x0 0x0 0x7>;
- interrupt-map = <
-
- // IDSEL 0x11 func 0 - PCI slot 1
- 0x8800 0x0 0x0 0x1 &i8259 0x9 0x2
- 0x8800 0x0 0x0 0x2 &i8259 0xa 0x2
-
- // IDSEL 0x11 func 1 - PCI slot 1
- 0x8900 0x0 0x0 0x1 &i8259 0x9 0x2
- 0x8900 0x0 0x0 0x2 &i8259 0xa 0x2
-
- // IDSEL 0x11 func 2 - PCI slot 1
- 0x8a00 0x0 0x0 0x1 &i8259 0x9 0x2
- 0x8a00 0x0 0x0 0x2 &i8259 0xa 0x2
-
- // IDSEL 0x11 func 3 - PCI slot 1
- 0x8b00 0x0 0x0 0x1 &i8259 0x9 0x2
- 0x8b00 0x0 0x0 0x2 &i8259 0xa 0x2
-
- // IDSEL 0x11 func 4 - PCI slot 1
- 0x8c00 0x0 0x0 0x1 &i8259 0x9 0x2
- 0x8c00 0x0 0x0 0x2 &i8259 0xa 0x2
-
- // IDSEL 0x11 func 5 - PCI slot 1
- 0x8d00 0x0 0x0 0x1 &i8259 0x9 0x2
- 0x8d00 0x0 0x0 0x2 &i8259 0xa 0x2
-
- // IDSEL 0x11 func 6 - PCI slot 1
- 0x8e00 0x0 0x0 0x1 &i8259 0x9 0x2
- 0x8e00 0x0 0x0 0x2 &i8259 0xa 0x2
-
- // IDSEL 0x11 func 7 - PCI slot 1
- 0x8f00 0x0 0x0 0x1 &i8259 0x9 0x2
- 0x8f00 0x0 0x0 0x2 &i8259 0xa 0x2
-
- // IDSEL 0x1d Audio
- 0xe800 0x0 0x0 0x1 &i8259 0x6 0x2
-
- // IDSEL 0x1e Legacy
- 0xf000 0x0 0x0 0x1 &i8259 0x7 0x2
- 0xf100 0x0 0x0 0x1 &i8259 0x7 0x2
-
- // IDSEL 0x1f IDE/SATA
- 0xf800 0x0 0x0 0x1 &i8259 0xe 0x2
- 0xf900 0x0 0x0 0x1 &i8259 0x5 0x2
- >;
-
+ reg = <0 0xffe09000 0 0x1000>;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
ranges = <0x2000000 0x0 0xa0000000
0x2000000 0x0 0xa0000000
0x0 0x20000000
@@ -309,89 +61,14 @@
0x1000000 0x0 0x0
0x1000000 0x0 0x0
0x0 0x10000>;
- uli1575@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- ranges = <0x2000000 0x0 0xa0000000
- 0x2000000 0x0 0xa0000000
- 0x0 0x20000000
-
- 0x1000000 0x0 0x0
- 0x1000000 0x0 0x0
- 0x0 0x10000>;
- isa@1e {
- device_type = "isa";
- #interrupt-cells = <2>;
- #size-cells = <1>;
- #address-cells = <2>;
- reg = <0xf000 0x0 0x0 0x0 0x0>;
- ranges = <0x1 0x0 0x1000000 0x0 0x0
- 0x1000>;
- interrupt-parent = <&i8259>;
-
- i8259: interrupt-controller@20 {
- reg = <0x1 0x20 0x2
- 0x1 0xa0 0x2
- 0x1 0x4d0 0x2>;
- interrupt-controller;
- device_type = "interrupt-controller";
- #address-cells = <0>;
- #interrupt-cells = <2>;
- compatible = "chrp,iic";
- interrupts = <4 1>;
- interrupt-parent = <&mpic>;
- };
-
- i8042@60 {
- #size-cells = <0>;
- #address-cells = <1>;
- reg = <0x1 0x60 0x1 0x1 0x64 0x1>;
- interrupts = <1 3 12 3>;
- interrupt-parent =
- <&i8259>;
-
- keyboard@0 {
- reg = <0x0>;
- compatible = "pnpPNP,303";
- };
-
- mouse@1 {
- reg = <0x1>;
- compatible = "pnpPNP,f03";
- };
- };
-
- rtc@70 {
- compatible = "pnpPNP,b00";
- reg = <0x1 0x70 0x2>;
- };
-
- gpio@400 {
- reg = <0x1 0x400 0x80>;
- };
- };
- };
};
-
};
- pci2: pcie@ffe0a000 {
+ pci0: pcie@ffe0a000 {
ranges = <0x2000000 0x0 0xc0000000 0 0xc0000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc20000 0x0 0x10000>;
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0x0 0x0 0x1 &mpic 0x0 0x1
- 0000 0x0 0x0 0x2 &mpic 0x1 0x1
- 0000 0x0 0x0 0x3 &mpic 0x2 0x1
- 0000 0x0 0x0 0x4 &mpic 0x3 0x1
- >;
+ reg = <0 0xffe0a000 0 0x1000>;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
ranges = <0x2000000 0x0 0xc0000000
0x2000000 0x0 0xc0000000
0x0 0x20000000
@@ -402,3 +79,11 @@
};
};
};
+
+/*
+ * p2020ds.dtsi must be last to ensure board_pci0 overrides pci0 settings
+ * for interrupt-map & interrupt-map-mask
+ */
+
+/include/ "fsl/p2020si-post.dtsi"
+/include/ "p2020ds.dtsi"
diff --git a/arch/powerpc/boot/dts/p2020ds.dtsi b/arch/powerpc/boot/dts/p2020ds.dtsi
new file mode 100644
index 0000000..c1cf6ce
--- /dev/null
+++ b/arch/powerpc/boot/dts/p2020ds.dtsi
@@ -0,0 +1,316 @@
+/*
+ * P2020DS Device Tree Source stub (no addresses or top-level ranges)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&board_lbc {
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x8000000>;
+ bank-width = <2>;
+ device-width = <1>;
+
+ ramdisk@0 {
+ reg = <0x0 0x03000000>;
+ read-only;
+ };
+
+ diagnostic@3000000 {
+ reg = <0x03000000 0x00e00000>;
+ read-only;
+ };
+
+ dink@3e00000 {
+ reg = <0x03e00000 0x00200000>;
+ read-only;
+ };
+
+ kernel@4000000 {
+ reg = <0x04000000 0x00400000>;
+ read-only;
+ };
+
+ jffs2@4400000 {
+ reg = <0x04400000 0x03b00000>;
+ };
+
+ dtb@7f00000 {
+ reg = <0x07f00000 0x00080000>;
+ read-only;
+ };
+
+ u-boot@7f80000 {
+ reg = <0x07f80000 0x00080000>;
+ read-only;
+ };
+ };
+
+ nand@2,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,elbc-fcm-nand";
+ reg = <0x2 0x0 0x40000>;
+
+ u-boot@0 {
+ reg = <0x0 0x02000000>;
+ read-only;
+ };
+
+ jffs2@2000000 {
+ reg = <0x02000000 0x10000000>;
+ };
+
+ ramdisk@12000000 {
+ reg = <0x12000000 0x08000000>;
+ read-only;
+ };
+
+ kernel@1a000000 {
+ reg = <0x1a000000 0x04000000>;
+ };
+
+ dtb@1e000000 {
+ reg = <0x1e000000 0x01000000>;
+ read-only;
+ };
+
+ empty@1f000000 {
+ reg = <0x1f000000 0x21000000>;
+ };
+ };
+
+ board-control@3,0 {
+ compatible = "fsl,p2020ds-fpga", "fsl,fpga-ngpixis";
+ reg = <0x3 0x0 0x30>;
+ };
+
+ nand@4,0 {
+ compatible = "fsl,elbc-fcm-nand";
+ reg = <0x4 0x0 0x40000>;
+ };
+
+ nand@5,0 {
+ compatible = "fsl,elbc-fcm-nand";
+ reg = <0x5 0x0 0x40000>;
+ };
+
+ nand@6,0 {
+ compatible = "fsl,elbc-fcm-nand";
+ reg = <0x6 0x0 0x40000>;
+ };
+};
+
+&board_soc {
+ usb@22000 {
+ phy_type = "ulpi";
+ };
+
+ mdio@24520 {
+ phy0: ethernet-phy@0 {
+ interrupts = <3 1 0 0>;
+ reg = <0x0>;
+ };
+ phy1: ethernet-phy@1 {
+ interrupts = <3 1 0 0>;
+ reg = <0x1>;
+ };
+ phy2: ethernet-phy@2 {
+ interrupts = <3 1 0 0>;
+ reg = <0x2>;
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+
+ };
+
+ mdio@25520 {
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ mdio@26520 {
+ tbi2: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+
+ };
+
+ ptp_clock@24e00 {
+ fsl,tclk-period = <5>;
+ fsl,tmr-prsc = <200>;
+ fsl,tmr-add = <0xCCCCCCCD>;
+ fsl,tmr-fiper1 = <0x3B9AC9FB>;
+ fsl,tmr-fiper2 = <0x0001869B>;
+ fsl,max-adj = <249999999>;
+ };
+
+ enet0: ethernet@24000 {
+ tbi-handle = <&tbi0>;
+ phy-handle = <&phy0>;
+ phy-connection-type = "rgmii-id";
+ };
+
+ enet1: ethernet@25000 {
+ tbi-handle = <&tbi1>;
+ phy-handle = <&phy1>;
+ phy-connection-type = "rgmii-id";
+
+ };
+
+ enet2: ethernet@26000 {
+ tbi-handle = <&tbi2>;
+ phy-handle = <&phy2>;
+ phy-connection-type = "rgmii-id";
+ };
+};
+
+&board_pci1 {
+ pcie@0 {
+ interrupt-map-mask = <0xff00 0x0 0x0 0x7>;
+ interrupt-map = <
+
+ // IDSEL 0x11 func 0 - PCI slot 1
+ 0x8800 0x0 0x0 0x1 &i8259 0x9 0x2
+ 0x8800 0x0 0x0 0x2 &i8259 0xa 0x2
+
+ // IDSEL 0x11 func 1 - PCI slot 1
+ 0x8900 0x0 0x0 0x1 &i8259 0x9 0x2
+ 0x8900 0x0 0x0 0x2 &i8259 0xa 0x2
+
+ // IDSEL 0x11 func 2 - PCI slot 1
+ 0x8a00 0x0 0x0 0x1 &i8259 0x9 0x2
+ 0x8a00 0x0 0x0 0x2 &i8259 0xa 0x2
+
+ // IDSEL 0x11 func 3 - PCI slot 1
+ 0x8b00 0x0 0x0 0x1 &i8259 0x9 0x2
+ 0x8b00 0x0 0x0 0x2 &i8259 0xa 0x2
+
+ // IDSEL 0x11 func 4 - PCI slot 1
+ 0x8c00 0x0 0x0 0x1 &i8259 0x9 0x2
+ 0x8c00 0x0 0x0 0x2 &i8259 0xa 0x2
+
+ // IDSEL 0x11 func 5 - PCI slot 1
+ 0x8d00 0x0 0x0 0x1 &i8259 0x9 0x2
+ 0x8d00 0x0 0x0 0x2 &i8259 0xa 0x2
+
+ // IDSEL 0x11 func 6 - PCI slot 1
+ 0x8e00 0x0 0x0 0x1 &i8259 0x9 0x2
+ 0x8e00 0x0 0x0 0x2 &i8259 0xa 0x2
+
+ // IDSEL 0x11 func 7 - PCI slot 1
+ 0x8f00 0x0 0x0 0x1 &i8259 0x9 0x2
+ 0x8f00 0x0 0x0 0x2 &i8259 0xa 0x2
+
+ // IDSEL 0x1d Audio
+ 0xe800 0x0 0x0 0x1 &i8259 0x6 0x2
+
+ // IDSEL 0x1e Legacy
+ 0xf000 0x0 0x0 0x1 &i8259 0x7 0x2
+ 0xf100 0x0 0x0 0x1 &i8259 0x7 0x2
+
+ // IDSEL 0x1f IDE/SATA
+ 0xf800 0x0 0x0 0x1 &i8259 0xe 0x2
+ 0xf900 0x0 0x0 0x1 &i8259 0x5 0x2
+ >;
+
+ uli1575@0 {
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ ranges = <0x2000000 0x0 0xa0000000
+ 0x2000000 0x0 0xa0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x10000>;
+ isa@1e {
+ device_type = "isa";
+ #interrupt-cells = <2>;
+ #size-cells = <1>;
+ #address-cells = <2>;
+ reg = <0xf000 0x0 0x0 0x0 0x0>;
+ ranges = <0x1 0x0 0x1000000 0x0 0x0
+ 0x1000>;
+ interrupt-parent = <&i8259>;
+
+ i8259: interrupt-controller@20 {
+ reg = <0x1 0x20 0x2
+ 0x1 0xa0 0x2
+ 0x1 0x4d0 0x2>;
+ interrupt-controller;
+ device_type = "interrupt-controller";
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ compatible = "chrp,iic";
+ interrupts = <4 1 0 0>;
+ interrupt-parent = <&mpic>;
+ };
+
+ i8042@60 {
+ #size-cells = <0>;
+ #address-cells = <1>;
+ reg = <0x1 0x60 0x1 0x1 0x64 0x1>;
+ interrupts = <1 3 12 3>;
+ interrupt-parent =
+ <&i8259>;
+
+ keyboard@0 {
+ reg = <0x0>;
+ compatible = "pnpPNP,303";
+ };
+
+ mouse@1 {
+ reg = <0x1>;
+ compatible = "pnpPNP,f03";
+ };
+ };
+
+ rtc@70 {
+ compatible = "pnpPNP,b00";
+ reg = <0x1 0x70 0x2>;
+ };
+
+ gpio@400 {
+ reg = <0x1 0x400 0x80>;
+ };
+ };
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p2020si.dtsi b/arch/powerpc/boot/dts/p2020si.dtsi
index 6def17f..37f7194 100644
--- a/arch/powerpc/boot/dts/p2020si.dtsi
+++ b/arch/powerpc/boot/dts/p2020si.dtsi
@@ -14,6 +14,7 @@
compatible = "fsl,P2020";
#address-cells = <2>;
#size-cells = <2>;
+ interrupt-parent = <&mpic>;
cpus {
#address-cells = <1>;
@@ -37,8 +38,7 @@
#size-cells = <1>;
compatible = "fsl,p2020-elbc", "fsl,elbc", "simple-bus";
reg = <0 0xffe05000 0 0x1000>;
- interrupts = <19 2>;
- interrupt-parent = <&mpic>;
+ interrupts = <19 2 0 0>;
};
soc@ffe00000 {
@@ -58,15 +58,13 @@
ecm@1000 {
compatible = "fsl,p2020-ecm", "fsl,ecm";
reg = <0x1000 0x1000>;
- interrupts = <17 2>;
- interrupt-parent = <&mpic>;
+ interrupts = <17 2 0 0>;
};
memory-controller@2000 {
compatible = "fsl,p2020-memory-controller";
reg = <0x2000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <18 2>;
+ interrupts = <18 2 0 0>;
};
i2c@3000 {
@@ -75,8 +73,7 @@
cell-index = <0>;
compatible = "fsl-i2c";
reg = <0x3000 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
+ interrupts = <43 2 0 0>;
dfsrr;
};
@@ -86,8 +83,7 @@
cell-index = <1>;
compatible = "fsl-i2c";
reg = <0x3100 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
+ interrupts = <43 2 0 0>;
dfsrr;
};
@@ -97,8 +93,7 @@
compatible = "ns16550";
reg = <0x4500 0x100>;
clock-frequency = <0>;
- interrupts = <42 2>;
- interrupt-parent = <&mpic>;
+ interrupts = <42 2 0 0>;
};
serial1: serial@4600 {
@@ -107,8 +102,7 @@
compatible = "ns16550";
reg = <0x4600 0x100>;
clock-frequency = <0>;
- interrupts = <42 2>;
- interrupt-parent = <&mpic>;
+ interrupts = <42 2 0 0>;
};
spi@7000 {
@@ -117,8 +111,7 @@
#size-cells = <0>;
compatible = "fsl,espi";
reg = <0x7000 0x1000>;
- interrupts = <59 0x2>;
- interrupt-parent = <&mpic>;
+ interrupts = <59 0x2 0 0>;
mode = "cpu";
};
@@ -133,29 +126,25 @@
compatible = "fsl,eloplus-dma-channel";
reg = <0x0 0x80>;
cell-index = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <76 2>;
+ interrupts = <76 2 0 0>;
};
dma-channel@80 {
compatible = "fsl,eloplus-dma-channel";
reg = <0x80 0x80>;
cell-index = <1>;
- interrupt-parent = <&mpic>;
- interrupts = <77 2>;
+ interrupts = <77 2 0 0>;
};
dma-channel@100 {
compatible = "fsl,eloplus-dma-channel";
reg = <0x100 0x80>;
cell-index = <2>;
- interrupt-parent = <&mpic>;
- interrupts = <78 2>;
+ interrupts = <78 2 0 0>;
};
dma-channel@180 {
compatible = "fsl,eloplus-dma-channel";
reg = <0x180 0x80>;
cell-index = <3>;
- interrupt-parent = <&mpic>;
- interrupts = <79 2>;
+ interrupts = <79 2 0 0>;
};
};
@@ -163,8 +152,7 @@
#gpio-cells = <2>;
compatible = "fsl,mpc8572-gpio";
reg = <0xf000 0x100>;
- interrupts = <47 0x2>;
- interrupt-parent = <&mpic>;
+ interrupts = <47 0x2 0 0>;
gpio-controller;
};
@@ -173,8 +161,7 @@
reg = <0x20000 0x1000>;
cache-line-size = <32>; // 32 bytes
cache-size = <0x80000>; // L2,512K
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
+ interrupts = <16 2 0 0>;
};
dma@21300 {
@@ -188,29 +175,25 @@
compatible = "fsl,eloplus-dma-channel";
reg = <0x0 0x80>;
cell-index = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <20 2>;
+ interrupts = <20 2 0 0>;
};
dma-channel@80 {
compatible = "fsl,eloplus-dma-channel";
reg = <0x80 0x80>;
cell-index = <1>;
- interrupt-parent = <&mpic>;
- interrupts = <21 2>;
+ interrupts = <21 2 0 0>;
};
dma-channel@100 {
compatible = "fsl,eloplus-dma-channel";
reg = <0x100 0x80>;
cell-index = <2>;
- interrupt-parent = <&mpic>;
- interrupts = <22 2>;
+ interrupts = <22 2 0 0>;
};
dma-channel@180 {
compatible = "fsl,eloplus-dma-channel";
reg = <0x180 0x80>;
cell-index = <3>;
- interrupt-parent = <&mpic>;
- interrupts = <23 2>;
+ interrupts = <23 2 0 0>;
};
};
@@ -219,8 +202,7 @@
#size-cells = <0>;
compatible = "fsl-usb2-dr";
reg = <0x22000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <28 0x2>;
+ interrupts = <28 0x2 0 0>;
};
mdio@24520 {
@@ -254,8 +236,7 @@
reg = <0x24000 0x1000>;
ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <29 2 30 2 34 2>;
- interrupt-parent = <&mpic>;
+ interrupts = <29 2 0 0 30 2 0 0 34 2 0 0>;
};
enet1: ethernet@25000 {
@@ -268,8 +249,7 @@
reg = <0x25000 0x1000>;
ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <35 2 36 2 40 2>;
- interrupt-parent = <&mpic>;
+ interrupts = <35 2 0 0 36 2 0 0 40 2 0 0>;
};
@@ -283,16 +263,14 @@
reg = <0x26000 0x1000>;
ranges = <0x0 0x26000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <31 2 32 2 33 2>;
- interrupt-parent = <&mpic>;
+ interrupts = <31 2 0 0 32 2 0 0 33 2 0 0>;
};
sdhci@2e000 {
compatible = "fsl,p2020-esdhc", "fsl,esdhc";
reg = <0x2e000 0x1000>;
- interrupts = <72 0x2>;
- interrupt-parent = <&mpic>;
+ interrupts = <72 0x2 0 0>;
/* Filled in by U-Boot */
clock-frequency = <0>;
};
@@ -301,8 +279,7 @@
compatible = "fsl,sec3.1", "fsl,sec3.0", "fsl,sec2.4",
"fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0";
reg = <0x30000 0x10000>;
- interrupts = <45 2 58 2>;
- interrupt-parent = <&mpic>;
+ interrupts = <45 2 0 0 58 2 0 0>;
fsl,num-channels = <4>;
fsl,channel-fifo-len = <24>;
fsl,exec-units-mask = <0xbfe>;
@@ -323,15 +300,14 @@
reg = <0x41600 0x80>;
msi-available-ranges = <0 0x100>;
interrupts = <
- 0xe0 0
- 0xe1 0
- 0xe2 0
- 0xe3 0
- 0xe4 0
- 0xe5 0
- 0xe6 0
- 0xe7 0>;
- interrupt-parent = <&mpic>;
+ 0xe0 0 0 0
+ 0xe1 0 0 0
+ 0xe2 0 0 0
+ 0xe3 0 0 0
+ 0xe4 0 0 0
+ 0xe5 0 0 0
+ 0xe6 0 0 0
+ 0xe7 0 0 0>;
};
global-utilities@e0000 { //global utilities block
@@ -350,8 +326,7 @@
reg = <0 0xffe08000 0 0x1000>;
bus-range = <0 255>;
clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <24 2>;
+ interrupts = <24 2 0 0>;
};
pci1: pcie@ffe09000 {
@@ -363,8 +338,7 @@
reg = <0 0xffe09000 0 0x1000>;
bus-range = <0 255>;
clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <25 2>;
+ interrupts = <25 2 0 0>;
};
pci2: pcie@ffe0a000 {
@@ -376,7 +350,6 @@
reg = <0 0xffe0a000 0 0x1000>;
bus-range = <0 255>;
clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <26 2>;
+ interrupts = <26 2 0 0>;
};
};
--
1.7.3.4
^ permalink raw reply related
* [PATCH 22/29] powerpc/85xx: Rework P1023RDS device tree
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-21-git-send-email-galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Dropping "fsl,p1023-IP..." from compatibles for standard blocks
* Removed incorrect power/pmc node, there are no etsec on P1023
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/fsl/p1023si-post.dtsi | 224 ++++++++++++++++
arch/powerpc/boot/dts/fsl/p1023si-pre.dtsi | 76 ++++++
arch/powerpc/boot/dts/p1023rds.dts | 380 ++-------------------------
3 files changed, 322 insertions(+), 358 deletions(-)
create mode 100644 arch/powerpc/boot/dts/fsl/p1023si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/p1023si-pre.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/p1023si-post.dtsi b/arch/powerpc/boot/dts/fsl/p1023si-post.dtsi
new file mode 100644
index 0000000..b06bb4c
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p1023si-post.dtsi
@@ -0,0 +1,224 @@
+/*
+ * P1023/P1017 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,p1023-elbc", "fsl,elbc", "simple-bus";
+ interrupts = <19 2 0 0>;
+};
+
+/* controller at 0xa000 */
+&pci0 {
+ compatible = "fsl,p1023-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 0 0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 0 0>;
+ };
+};
+
+/* controller at 0x9000 */
+&pci1 {
+ compatible = "fsl,p1023-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 0 0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 0 0>;
+ };
+};
+
+/* controller at 0xb000 */
+&pci2 {
+ compatible = "fsl,p1023-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 0 0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 0 0>;
+ };
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "fsl,p1023-immr", "simple-bus";
+ bus-frequency = <0>; // Filled out by uboot.
+
+ ecm-law@0 {
+ compatible = "fsl,ecm-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <12>;
+ };
+
+ ecm@1000 {
+ compatible = "fsl,p1023-ecm", "fsl,ecm";
+ reg = <0x1000 0x1000>;
+ interrupts = <16 2 0 0>;
+ };
+
+ memory-controller@2000 {
+ compatible = "fsl,p1023-memory-controller";
+ reg = <0x2000 0x1000>;
+ interrupts = <16 2 0 0>;
+ };
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-duart-0.dtsi"
+
+/include/ "pq3-espi-0.dtsi"
+ spi@7000 {
+ fsl,espi-num-chipselects = <4>;
+ };
+
+/include/ "pq3-gpio-0.dtsi"
+
+ L2: l2-cache-controller@20000 {
+ compatible = "fsl,p1023-l2-cache-controller";
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x40000>; // L2,256K
+ interrupts = <16 2 0 0>;
+ };
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-usb2-dr-0.dtsi"
+
+ crypto: crypto@300000 {
+ compatible = "fsl,sec-v4.2", "fsl,sec-v4.0";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x30000 0x10000>;
+ ranges = <0 0x30000 0x10000>;
+ interrupts = <58 2 0 0>;
+
+ sec_jr0: jr@1000 {
+ compatible = "fsl,sec-v4.2-job-ring",
+ "fsl,sec-v4.0-job-ring";
+ reg = <0x1000 0x1000>;
+ interrupts = <45 2 0 0>;
+ };
+
+ sec_jr1: jr@2000 {
+ compatible = "fsl,sec-v4.2-job-ring",
+ "fsl,sec-v4.0-job-ring";
+ reg = <0x2000 0x1000>;
+ interrupts = <45 2 0 0>;
+ };
+
+ sec_jr2: jr@3000 {
+ compatible = "fsl,sec-v4.2-job-ring",
+ "fsl,sec-v4.0-job-ring";
+ reg = <0x3000 0x1000>;
+ interrupts = <57 2 0 0>;
+ };
+
+ sec_jr3: jr@4000 {
+ compatible = "fsl,sec-v4.2-job-ring",
+ "fsl,sec-v4.0-job-ring";
+ reg = <0x4000 0x1000>;
+ interrupts = <57 2 0 0>;
+ };
+
+ rtic@6000 {
+ compatible = "fsl,sec-v4.2-rtic",
+ "fsl,sec-v4.0-rtic";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x6000 0x100>;
+ ranges = <0x0 0x6100 0xe00>;
+
+ rtic_a: rtic-a@0 {
+ compatible = "fsl,sec-v4.2-rtic-memory",
+ "fsl,sec-v4.0-rtic-memory";
+ reg = <0x00 0x20 0x100 0x80>;
+ };
+
+ rtic_b: rtic-b@20 {
+ compatible = "fsl,sec-v4.2-rtic-memory",
+ "fsl,sec-v4.0-rtic-memory";
+ reg = <0x20 0x20 0x200 0x80>;
+ };
+
+ rtic_c: rtic-c@40 {
+ compatible = "fsl,sec-v4.2-rtic-memory",
+ "fsl,sec-v4.0-rtic-memory";
+ reg = <0x40 0x20 0x300 0x80>;
+ };
+
+ rtic_d: rtic-d@60 {
+ compatible = "fsl,sec-v4.2-rtic-memory",
+ "fsl,sec-v4.0-rtic-memory";
+ reg = <0x60 0x20 0x500 0x80>;
+ };
+ };
+ };
+
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-mpic-timer-B.dtsi"
+
+ global-utilities@e0000 {
+ compatible = "fsl,p1023-guts";
+ reg = <0xe0000 0x1000>;
+ fsl,has-rstcr;
+ };
+};
diff --git a/arch/powerpc/boot/dts/fsl/p1023si-pre.dtsi b/arch/powerpc/boot/dts/fsl/p1023si-pre.dtsi
new file mode 100644
index 0000000..ac45f6d
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p1023si-pre.dtsi
@@ -0,0 +1,76 @@
+/*
+ * P1023/P1017 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+ compatible = "fsl,P1023";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
+
+ crypto = &crypto;
+ sec_jr0 = &sec_jr0;
+ sec_jr1 = &sec_jr1;
+ sec_jr2 = &sec_jr2;
+ sec_jr3 = &sec_jr3;
+ rtic_a = &rtic_a;
+ rtic_b = &rtic_b;
+ rtic_c = &rtic_c;
+ rtic_d = &rtic_d;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,P1023@0 {
+ device_type = "cpu";
+ reg = <0x0>;
+ next-level-cache = <&L2>;
+ };
+
+ PowerPC,P1023@1 {
+ device_type = "cpu";
+ reg = <0x1>;
+ next-level-cache = <&L2>;
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p1023rds.dts b/arch/powerpc/boot/dts/p1023rds.dts
index d3b4782..beb6cb1 100644
--- a/arch/powerpc/boot/dts/p1023rds.dts
+++ b/arch/powerpc/boot/dts/p1023rds.dts
@@ -34,137 +34,30 @@
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
-/dts-v1/;
+/include/ "fsl/p1023si-pre.dtsi"
/ {
model = "fsl,P1023";
compatible = "fsl,P1023RDS";
#address-cells = <2>;
#size-cells = <2>;
-
- aliases {
- serial0 = &serial0;
- serial1 = &serial1;
- pci0 = &pci0;
- pci1 = &pci1;
- pci2 = &pci2;
-
- crypto = &crypto;
- sec_jr0 = &sec_jr0;
- sec_jr1 = &sec_jr1;
- sec_jr2 = &sec_jr2;
- sec_jr3 = &sec_jr3;
- rtic_a = &rtic_a;
- rtic_b = &rtic_b;
- rtic_c = &rtic_c;
- rtic_d = &rtic_d;
- };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu0: PowerPC,P1023@0 {
- device_type = "cpu";
- reg = <0x0>;
- next-level-cache = <&L2>;
- };
-
- cpu1: PowerPC,P1023@1 {
- device_type = "cpu";
- reg = <0x1>;
- next-level-cache = <&L2>;
- };
- };
+ interrupt-parent = <&mpic>;
memory {
device_type = "memory";
};
- soc@ff600000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "soc";
- compatible = "fsl,p1023-immr", "simple-bus";
+ soc: soc@ff600000 {
ranges = <0x0 0x0 0xff600000 0x200000>;
- bus-frequency = <0>; // Filled out by uboot.
-
- ecm-law@0 {
- compatible = "fsl,ecm-law";
- reg = <0x0 0x1000>;
- fsl,num-laws = <12>;
- };
-
- ecm@1000 {
- compatible = "fsl,p1023-ecm", "fsl,ecm";
- reg = <0x1000 0x1000>;
- interrupts = <16 2>;
- interrupt-parent = <&mpic>;
- };
-
- memory-controller@2000 {
- compatible = "fsl,p1023-memory-controller";
- reg = <0x2000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- };
i2c@3000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x3000 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
- dfsrr;
rtc@68 {
compatible = "dallas,ds1374";
reg = <0x68>;
};
};
- i2c@3100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- compatible = "fsl-i2c";
- reg = <0x3100 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
- dfsrr;
- };
-
- serial0: serial@4500 {
- cell-index = <0>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4500 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2>;
- interrupt-parent = <&mpic>;
- };
-
- serial1: serial@4600 {
- cell-index = <1>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4600 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2>;
- interrupt-parent = <&mpic>;
- };
-
spi@7000 {
- cell-index = <0>;
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,p1023-espi", "fsl,mpc8536-espi";
- reg = <0x7000 0x1000>;
- interrupts = <59 0x2>;
- interrupt-parent = <&mpic>;
- fsl,espi-num-chipselects = <4>;
-
fsl_dataflash@0 {
#address-cells = <1>;
#size-cells = <1>;
@@ -186,197 +79,14 @@
};
};
- gpio: gpio-controller@f000 {
- #gpio-cells = <2>;
- compatible = "fsl,qoriq-gpio";
- reg = <0xf000 0x100>;
- interrupts = <47 0x2>;
- interrupt-parent = <&mpic>;
- gpio-controller;
- };
-
- L2: l2-cache-controller@20000 {
- compatible = "fsl,p1023-l2-cache-controller";
- reg = <0x20000 0x1000>;
- cache-line-size = <32>; // 32 bytes
- cache-size = <0x40000>; // L2,256K
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- };
-
- dma@21300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,eloplus-dma";
- reg = <0x21300 0x4>;
- ranges = <0x0 0x21100 0x200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <20 2>;
- };
- dma-channel@80 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupt-parent = <&mpic>;
- interrupts = <21 2>;
- };
- dma-channel@100 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupt-parent = <&mpic>;
- interrupts = <22 2>;
- };
- dma-channel@180 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupt-parent = <&mpic>;
- interrupts = <23 2>;
- };
- };
-
usb@22000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl-usb2-dr";
- reg = <0x22000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <28 0x2>;
dr_mode = "host";
phy_type = "ulpi";
};
-
- crypto: crypto@300000 {
- compatible = "fsl,sec-v4.2", "fsl,sec-v4.0";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x30000 0x10000>;
- ranges = <0 0x30000 0x10000>;
- interrupt-parent = <&mpic>;
- interrupts = <58 2>;
-
- sec_jr0: jr@1000 {
- compatible = "fsl,sec-v4.2-job-ring",
- "fsl,sec-v4.0-job-ring";
- reg = <0x1000 0x1000>;
- interrupts = <45 2>;
- };
-
- sec_jr1: jr@2000 {
- compatible = "fsl,sec-v4.2-job-ring",
- "fsl,sec-v4.0-job-ring";
- reg = <0x2000 0x1000>;
- interrupts = <45 2>;
- };
-
- sec_jr2: jr@3000 {
- compatible = "fsl,sec-v4.2-job-ring",
- "fsl,sec-v4.0-job-ring";
- reg = <0x3000 0x1000>;
- interrupts = <57 2>;
- };
-
- sec_jr3: jr@4000 {
- compatible = "fsl,sec-v4.2-job-ring",
- "fsl,sec-v4.0-job-ring";
- reg = <0x4000 0x1000>;
- interrupts = <57 2>;
- };
-
- rtic@6000 {
- compatible = "fsl,sec-v4.2-rtic",
- "fsl,sec-v4.0-rtic";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x6000 0x100>;
- ranges = <0x0 0x6100 0xe00>;
-
- rtic_a: rtic-a@0 {
- compatible = "fsl,sec-v4.2-rtic-memory",
- "fsl,sec-v4.0-rtic-memory";
- reg = <0x00 0x20 0x100 0x80>;
- };
-
- rtic_b: rtic-b@20 {
- compatible = "fsl,sec-v4.2-rtic-memory",
- "fsl,sec-v4.0-rtic-memory";
- reg = <0x20 0x20 0x200 0x80>;
- };
-
- rtic_c: rtic-c@40 {
- compatible = "fsl,sec-v4.2-rtic-memory",
- "fsl,sec-v4.0-rtic-memory";
- reg = <0x40 0x20 0x300 0x80>;
- };
-
- rtic_d: rtic-d@60 {
- compatible = "fsl,sec-v4.2-rtic-memory",
- "fsl,sec-v4.0-rtic-memory";
- reg = <0x60 0x20 0x500 0x80>;
- };
- };
- };
-
- power@e0070{
- compatible = "fsl,mpc8536-pmc", "fsl,mpc8548-pmc",
- "fsl,p1022-pmc";
- reg = <0xe0070 0x20>;
- etsec1_clk: soc-clk@B0{
- fsl,pmcdr-mask = <0x00000080>;
- };
- etsec2_clk: soc-clk@B1{
- fsl,pmcdr-mask = <0x00000040>;
- };
- etsec3_clk: soc-clk@B2{
- fsl,pmcdr-mask = <0x00000020>;
- };
- };
-
- mpic: pic@40000 {
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <2>;
- reg = <0x40000 0x40000>;
- compatible = "chrp,open-pic";
- device_type = "open-pic";
- };
-
- msi@41600 {
- compatible = "fsl,p1023-msi", "fsl,mpic-msi";
- reg = <0x41600 0x80>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe0 0
- 0xe1 0
- 0xe2 0
- 0xe3 0
- 0xe4 0
- 0xe5 0
- 0xe6 0
- 0xe7 0>;
- interrupt-parent = <&mpic>;
- };
-
- global-utilities@e0000 { //global utilities block
- compatible = "fsl,p1023-guts";
- reg = <0xe0000 0x1000>;
- fsl,has-rstcr;
- };
};
- localbus@ff605000 {
- #address-cells = <2>;
- #size-cells = <1>;
- compatible = "fsl,p1023-elbc", "fsl,elbc", "simple-bus";
+ lbc: localbus@ff605000 {
reg = <0 0xff605000 0 0x1000>;
- interrupts = <19 2>;
- interrupt-parent = <&mpic>;
/* NOR Flash, BCSR */
ranges = <0x0 0x0 0x0 0xee000000 0x02000000
@@ -428,34 +138,18 @@
};
pci0: pcie@ff60a000 {
- compatible = "fsl,p1023-pcie", "fsl,qoriq-pcie-v2.2";
- cell-index = <1>;
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
reg = <0 0xff60a000 0 0x1000>;
- bus-range = <0 255>;
ranges = <0x2000000 0x0 0xc0000000 0 0xc0000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc20000 0x0 0x10000>;
- clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- interrupt-map-mask = <0xf800 0 0 7>;
/* IRQ[0:3] are pulled up on board, set to active-low */
+ interrupt-map-mask = <0xf800 0 0 7>;
interrupt-map = <
/* IDSEL 0x0 */
- 0000 0 0 1 &mpic 0 1
- 0000 0 0 2 &mpic 1 1
- 0000 0 0 3 &mpic 2 1
- 0000 0 0 4 &mpic 3 1
+ 0000 0 0 1 &mpic 0 1 0 0
+ 0000 0 0 2 &mpic 1 1 0 0
+ 0000 0 0 3 &mpic 2 1 0 0
+ 0000 0 0 4 &mpic 3 1 0 0
>;
ranges = <0x2000000 0x0 0xc0000000
0x2000000 0x0 0xc0000000
@@ -467,38 +161,22 @@
};
};
- pci1: pcie@ff609000 {
- compatible = "fsl,p1023-pcie", "fsl,qoriq-pcie-v2.2";
- cell-index = <2>;
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
+ board_pci1: pci1: pcie@ff609000 {
reg = <0 0xff609000 0 0x1000>;
- bus-range = <0 255>;
ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
- clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- interrupt-map-mask = <0xf800 0 0 7>;
/*
* IRQ[4:6] only for PCIe, set to active-high,
* IRQ[7] is pulled up on board, set to active-low
*/
+ interrupt-map-mask = <0xf800 0 0 7>;
interrupt-map = <
/* IDSEL 0x0 */
- 0000 0 0 1 &mpic 4 2
- 0000 0 0 2 &mpic 5 2
- 0000 0 0 3 &mpic 6 2
- 0000 0 0 4 &mpic 7 1
+ 0000 0 0 1 &mpic 4 2 0 0
+ 0000 0 0 2 &mpic 5 2 0 0
+ 0000 0 0 3 &mpic 6 2 0 0
+ 0000 0 0 4 &mpic 7 1 0 0
>;
ranges = <0x2000000 0x0 0xa0000000
0x2000000 0x0 0xa0000000
@@ -511,37 +189,21 @@
};
pci2: pcie@ff60b000 {
- cell-index = <3>;
- compatible = "fsl,p1023-pcie", "fsl,qoriq-pcie-v2.2";
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
reg = <0 0xff60b000 0 0x1000>;
- bus-range = <0 255>;
ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
- clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- interrupt-map-mask = <0xf800 0 0 7>;
/*
* IRQ[8:10] are pulled up on board, set to active-low
* IRQ[11] only for PCIe, set to active-high,
*/
+ interrupt-map-mask = <0xf800 0 0 7>;
interrupt-map = <
/* IDSEL 0x0 */
- 0000 0 0 1 &mpic 8 1
- 0000 0 0 2 &mpic 9 1
- 0000 0 0 3 &mpic 10 1
- 0000 0 0 4 &mpic 11 2
+ 0000 0 0 1 &mpic 8 1 0 0
+ 0000 0 0 2 &mpic 9 1 0 0
+ 0000 0 0 3 &mpic 10 1 0 0
+ 0000 0 0 4 &mpic 11 2 0 0
>;
ranges = <0x2000000 0x0 0x80000000
0x2000000 0x0 0x80000000
@@ -553,3 +215,5 @@
};
};
};
+
+/include/ "fsl/p1023si-post.dtsi"
--
1.7.3.4
^ permalink raw reply related
* [PATCH 21/29] powerpc/85xx: Rework P1022DS device tree
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-20-git-send-email-galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Updated spi node to new espi binding specification
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Added usb node for 2nd usb controller
* Dropping "fsl,p1022-IP..." from compatibles for standard blocks
* Fixed bug in local bus range node for CS2, was maping to
0x0 0x0xffa00000 instead of 0xf 0xffa00000
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/fsl/p1022si-post.dtsi | 235 +++++++++++++++
arch/powerpc/boot/dts/fsl/p1022si-pre.dtsi | 68 +++++
arch/powerpc/boot/dts/p1022ds.dts | 433 +--------------------------
3 files changed, 319 insertions(+), 417 deletions(-)
create mode 100644 arch/powerpc/boot/dts/fsl/p1022si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/p1022si-pre.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/p1022si-post.dtsi b/arch/powerpc/boot/dts/fsl/p1022si-post.dtsi
new file mode 100644
index 0000000..16239b1
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p1022si-post.dtsi
@@ -0,0 +1,235 @@
+/*
+ * P1022/P1013 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,p1022-elbc", "fsl,elbc", "simple-bus";
+ interrupts = <19 2 0 0>;
+};
+
+/* controller at 0x9000 */
+&pci0 {
+ compatible = "fsl,p1022-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 0 0>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x4 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x5 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0x6 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0x7 0x1 0x0 0x0
+ >;
+ };
+};
+
+/* controller at 0xa000 */
+&pci1 {
+ compatible = "fsl,p1022-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 0 0>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+ >;
+ };
+};
+
+/* controller at 0xb000 */
+&pci2 {
+ compatible = "fsl,p1022-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 0 0>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x8 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x9 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0xa 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0xb 0x1 0x0 0x0
+ >;
+ };
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "fsl,p1022-immr", "simple-bus";
+ bus-frequency = <0>; // Filled out by uboot.
+
+ ecm-law@0 {
+ compatible = "fsl,ecm-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <12>;
+ };
+
+ ecm@1000 {
+ compatible = "fsl,p1022-ecm", "fsl,ecm";
+ reg = <0x1000 0x1000>;
+ interrupts = <16 2 0 0>;
+ };
+
+ memory-controller@2000 {
+ compatible = "fsl,p1022-memory-controller";
+ reg = <0x2000 0x1000>;
+ interrupts = <16 2 0 0>;
+ };
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-duart-0.dtsi"
+/include/ "pq3-espi-0.dtsi"
+ spi@7000 {
+ fsl,espi-num-chipselects = <4>;
+ };
+
+/include/ "pq3-dma-1.dtsi"
+ dma@c300 {
+ dma00: dma-channel@0 {
+ compatible = "fsl,ssi-dma-channel";
+ };
+ dma01: dma-channel@80 {
+ compatible = "fsl,ssi-dma-channel";
+ };
+ };
+
+/include/ "pq3-gpio-0.dtsi"
+
+ display@10000 {
+ compatible = "fsl,diu", "fsl,p1022-diu";
+ reg = <0x10000 1000>;
+ interrupts = <64 2 0 0>;
+ };
+
+ ssi@15000 {
+ compatible = "fsl,mpc8610-ssi";
+ cell-index = <0>;
+ reg = <0x15000 0x100>;
+ interrupts = <75 2 0 0>;
+ fsl,playback-dma = <&dma00>;
+ fsl,capture-dma = <&dma01>;
+ fsl,fifo-depth = <15>;
+ };
+
+/include/ "pq3-sata2-0.dtsi"
+/include/ "pq3-sata2-1.dtsi"
+
+ L2: l2-cache-controller@20000 {
+ compatible = "fsl,p1022-l2-cache-controller";
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x40000>; // L2,256K
+ interrupts = <16 2 0 0>;
+ };
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-usb2-dr-0.dtsi"
+/include/ "pq3-usb2-dr-1.dtsi"
+
+/include/ "pq3-esdhc-0.dtsi"
+ sdhc@2e000 {
+ fsl,sdhci-auto-cmd12;
+ };
+
+/include/ "pq3-sec3.3-0.dtsi"
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-mpic-timer-B.dtsi"
+
+/include/ "pq3-etsec2-0.dtsi"
+ enet0: enet0_grp2: ethernet@b0000 {
+ };
+
+/include/ "pq3-etsec2-1.dtsi"
+ enet1: enet1_grp2: ethernet@b1000 {
+ };
+
+ global-utilities@e0000 {
+ compatible = "fsl,p1022-guts";
+ reg = <0xe0000 0x1000>;
+ fsl,has-rstcr;
+ };
+
+ power@e0070{
+ compatible = "fsl,mpc8536-pmc", "fsl,mpc8548-pmc";
+ reg = <0xe0070 0x20>;
+ };
+
+};
+
+/include/ "pq3-etsec2-grp2-0.dtsi"
+/include/ "pq3-etsec2-grp2-1.dtsi"
diff --git a/arch/powerpc/boot/dts/fsl/p1022si-pre.dtsi b/arch/powerpc/boot/dts/fsl/p1022si-pre.dtsi
new file mode 100644
index 0000000..e930f4f
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p1022si-pre.dtsi
@@ -0,0 +1,68 @@
+/*
+ * P1022/P1013 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+ compatible = "fsl,P1022";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,P1022@0 {
+ device_type = "cpu";
+ reg = <0x0>;
+ next-level-cache = <&L2>;
+ };
+
+ PowerPC,P1022@1 {
+ device_type = "cpu";
+ reg = <0x1>;
+ next-level-cache = <&L2>;
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p1022ds.dts b/arch/powerpc/boot/dts/p1022ds.dts
index b9b8719..35e0eee 100644
--- a/arch/powerpc/boot/dts/p1022ds.dts
+++ b/arch/powerpc/boot/dts/p1022ds.dts
@@ -8,55 +8,20 @@
* kind, whether express or implied.
*/
-/dts-v1/;
+/include/ "fsl/p1022si-pre.dtsi"
/ {
- model = "fsl,P1022";
+ model = "fsl,P1022DS";
compatible = "fsl,P1022DS";
- #address-cells = <2>;
- #size-cells = <2>;
- interrupt-parent = <&mpic>;
-
- aliases {
- ethernet0 = &enet0;
- ethernet1 = &enet1;
- serial0 = &serial0;
- serial1 = &serial1;
- pci0 = &pci0;
- pci1 = &pci1;
- pci2 = &pci2;
- };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- PowerPC,P1022@0 {
- device_type = "cpu";
- reg = <0x0>;
- next-level-cache = <&L2>;
- };
-
- PowerPC,P1022@1 {
- device_type = "cpu";
- reg = <0x1>;
- next-level-cache = <&L2>;
- };
- };
memory {
device_type = "memory";
};
- localbus@fffe05000 {
- #address-cells = <2>;
- #size-cells = <1>;
- compatible = "fsl,p1022-elbc", "fsl,elbc", "simple-bus";
+ lbc: localbus@fffe05000 {
reg = <0 0xffe05000 0 0x1000>;
- interrupts = <19 2 0 0>;
-
ranges = <0x0 0x0 0xf 0xe8000000 0x08000000
0x1 0x0 0xf 0xe0000000 0x08000000
- 0x2 0x0 0x0 0xffa00000 0x00040000
+ 0x2 0x0 0xf 0xffa00000 0x00040000
0x3 0x0 0xf 0xffdf0000 0x00008000>;
nor@0,0 {
@@ -161,51 +126,10 @@
};
};
- soc@fffe00000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "soc";
- compatible = "fsl,p1022-immr", "simple-bus";
+ soc: soc@fffe00000 {
ranges = <0x0 0xf 0xffe00000 0x100000>;
- bus-frequency = <0>; // Filled out by uboot.
-
- ecm-law@0 {
- compatible = "fsl,ecm-law";
- reg = <0x0 0x1000>;
- fsl,num-laws = <12>;
- };
-
- ecm@1000 {
- compatible = "fsl,p1022-ecm", "fsl,ecm";
- reg = <0x1000 0x1000>;
- interrupts = <16 2 0 0>;
- };
-
- memory-controller@2000 {
- compatible = "fsl,p1022-memory-controller";
- reg = <0x2000 0x1000>;
- interrupts = <16 2 0 0>;
- };
-
- i2c@3000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x3000 0x100>;
- interrupts = <43 2 0 0>;
- dfsrr;
- };
i2c@3100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- compatible = "fsl-i2c";
- reg = <0x3100 0x100>;
- interrupts = <43 2 0 0>;
- dfsrr;
-
wm8776:codec@1a {
compatible = "wlf,wm8776";
reg = <0x1a>;
@@ -216,41 +140,14 @@
};
};
- serial0: serial@4500 {
- cell-index = <0>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4500 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2 0 0>;
- };
-
- serial1: serial@4600 {
- cell-index = <1>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4600 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2 0 0>;
- };
-
spi@7000 {
- cell-index = <0>;
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,espi";
- reg = <0x7000 0x1000>;
- interrupts = <59 0x2 0 0>;
- espi,num-ss-bits = <4>;
- mode = "cpu";
-
- fsl_m25p80@0 {
+ flash@0 {
#address-cells = <1>;
#size-cells = <1>;
- compatible = "fsl,espi-flash";
+ compatible = "spansion,s25sl12801";
reg = <0>;
- linux,modalias = "fsl_m25p80";
spi-max-frequency = <40000000>; /* input clock */
+
partition@0 {
label = "u-boot-spi";
reg = <0x00000000 0x00100000>;
@@ -274,115 +171,20 @@
};
ssi@15000 {
- compatible = "fsl,mpc8610-ssi";
- cell-index = <0>;
- reg = <0x15000 0x100>;
- interrupts = <75 2 0 0>;
fsl,mode = "i2s-slave";
codec-handle = <&wm8776>;
- fsl,playback-dma = <&dma00>;
- fsl,capture-dma = <&dma01>;
- fsl,fifo-depth = <15>;
fsl,ssi-asynchronous;
};
- dma@c300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,eloplus-dma";
- reg = <0xc300 0x4>;
- ranges = <0x0 0xc100 0x200>;
- cell-index = <1>;
- dma00: dma-channel@0 {
- compatible = "fsl,ssi-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupts = <76 2 0 0>;
- };
- dma01: dma-channel@80 {
- compatible = "fsl,ssi-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupts = <77 2 0 0>;
- };
- dma-channel@100 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupts = <78 2 0 0>;
- };
- dma-channel@180 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupts = <79 2 0 0>;
- };
- };
-
- gpio: gpio-controller@f000 {
- #gpio-cells = <2>;
- compatible = "fsl,mpc8572-gpio";
- reg = <0xf000 0x100>;
- interrupts = <47 0x2 0 0>;
- gpio-controller;
- };
-
- L2: l2-cache-controller@20000 {
- compatible = "fsl,p1022-l2-cache-controller";
- reg = <0x20000 0x1000>;
- cache-line-size = <32>; // 32 bytes
- cache-size = <0x40000>; // L2, 256K
- interrupts = <16 2 0 0>;
- };
-
- dma@21300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,eloplus-dma";
- reg = <0x21300 0x4>;
- ranges = <0x0 0x21100 0x200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupts = <20 2 0 0>;
- };
- dma-channel@80 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupts = <21 2 0 0>;
- };
- dma-channel@100 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupts = <22 2 0 0>;
- };
- dma-channel@180 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupts = <23 2 0 0>;
- };
- };
-
usb@22000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl-usb2-dr";
- reg = <0x22000 0x1000>;
- interrupts = <28 0x2 0 0>;
phy_type = "ulpi";
};
- mdio@24000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,etsec2-mdio";
- reg = <0x24000 0x1000 0xb0030 0x4>;
+ usb@23000 {
+ status = "disabled";
+ };
+ mdio@24000 {
phy0: ethernet-phy@0 {
interrupts = <3 1 0 0>;
reg = <0x1>;
@@ -393,187 +195,22 @@
};
};
- mdio@25000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,etsec2-mdio";
- reg = <0x25000 0x1000 0xb1030 0x4>;
- };
-
- enet0: ethernet@B0000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <0>;
- device_type = "network";
- model = "eTSEC";
- compatible = "fsl,etsec2";
- fsl,num_rx_queues = <0x8>;
- fsl,num_tx_queues = <0x8>;
- fsl,magic-packet;
- fsl,wake-on-filer;
- local-mac-address = [ 00 00 00 00 00 00 ];
+ ethernet@b0000 {
phy-handle = <&phy0>;
phy-connection-type = "rgmii-id";
- queue-group@0{
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xB0000 0x1000>;
- interrupts = <29 2 0 0 30 2 0 0 34 2 0 0>;
- };
- queue-group@1{
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xB4000 0x1000>;
- interrupts = <17 2 0 0 18 2 0 0 24 2 0 0>;
- };
};
- enet1: ethernet@B1000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <0>;
- device_type = "network";
- model = "eTSEC";
- compatible = "fsl,etsec2";
- fsl,num_rx_queues = <0x8>;
- fsl,num_tx_queues = <0x8>;
- local-mac-address = [ 00 00 00 00 00 00 ];
+ ethernet@b1000 {
phy-handle = <&phy1>;
phy-connection-type = "rgmii-id";
- queue-group@0{
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xB1000 0x1000>;
- interrupts = <35 2 0 0 36 2 0 0 40 2 0 0>;
- };
- queue-group@1{
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xB5000 0x1000>;
- interrupts = <51 2 0 0 52 2 0 0 67 2 0 0>;
- };
- };
-
- sdhci@2e000 {
- compatible = "fsl,p1022-esdhc", "fsl,esdhc";
- reg = <0x2e000 0x1000>;
- interrupts = <72 0x2 0 0>;
- fsl,sdhci-auto-cmd12;
- /* Filled in by U-Boot */
- clock-frequency = <0>;
- };
-
- crypto@30000 {
- compatible = "fsl,sec3.3", "fsl,sec3.1", "fsl,sec3.0",
- "fsl,sec2.4", "fsl,sec2.2", "fsl,sec2.1",
- "fsl,sec2.0";
- reg = <0x30000 0x10000>;
- interrupts = <45 2 0 0 58 2 0 0>;
- fsl,num-channels = <4>;
- fsl,channel-fifo-len = <24>;
- fsl,exec-units-mask = <0x97c>;
- fsl,descriptor-types-mask = <0x3a30abf>;
- };
-
- sata@18000 {
- compatible = "fsl,p1022-sata", "fsl,pq-sata-v2";
- reg = <0x18000 0x1000>;
- cell-index = <1>;
- interrupts = <74 0x2 0 0>;
- };
-
- sata@19000 {
- compatible = "fsl,p1022-sata", "fsl,pq-sata-v2";
- reg = <0x19000 0x1000>;
- cell-index = <2>;
- interrupts = <41 0x2 0 0>;
- };
-
- power@e0070{
- compatible = "fsl,mpc8536-pmc", "fsl,mpc8548-pmc";
- reg = <0xe0070 0x20>;
- };
-
- display@10000 {
- compatible = "fsl,diu", "fsl,p1022-diu";
- reg = <0x10000 1000>;
- interrupts = <64 2 0 0>;
- };
-
- timer@41100 {
- compatible = "fsl,mpic-global-timer";
- reg = <0x41100 0x100 0x41300 4>;
- interrupts = <0 0 3 0
- 1 0 3 0
- 2 0 3 0
- 3 0 3 0>;
- };
-
- timer@42100 {
- compatible = "fsl,mpic-global-timer";
- reg = <0x42100 0x100 0x42300 4>;
- interrupts = <4 0 3 0
- 5 0 3 0
- 6 0 3 0
- 7 0 3 0>;
- };
-
- mpic: pic@40000 {
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <4>;
- reg = <0x40000 0x40000>;
- compatible = "fsl,mpic";
- device_type = "open-pic";
- };
-
- msi@41600 {
- compatible = "fsl,p1022-msi", "fsl,mpic-msi";
- reg = <0x41600 0x80>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe0 0 0 0
- 0xe1 0 0 0
- 0xe2 0 0 0
- 0xe3 0 0 0
- 0xe4 0 0 0
- 0xe5 0 0 0
- 0xe6 0 0 0
- 0xe7 0 0 0>;
- };
-
- global-utilities@e0000 { //global utilities block
- compatible = "fsl,p1022-guts";
- reg = <0xe0000 0x1000>;
- fsl,has-rstcr;
};
};
pci0: pcie@fffe09000 {
- compatible = "fsl,p1022-pcie";
- device_type = "pci";
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
reg = <0xf 0xffe09000 0 0x1000>;
- bus-range = <0 255>;
ranges = <0x2000000 0x0 0xa0000000 0xc 0x20000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0xf 0xffc10000 0x0 0x10000>;
- clock-frequency = <33333333>;
- interrupts = <16 2 0 0>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0 0 1 &mpic 4 1
- 0000 0 0 2 &mpic 5 1
- 0000 0 0 3 &mpic 6 1
- 0000 0 0 4 &mpic 7 1
- >;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
ranges = <0x2000000 0x0 0xe0000000
0x2000000 0x0 0xe0000000
0x0 0x20000000
@@ -585,30 +222,11 @@
};
pci1: pcie@fffe0a000 {
- compatible = "fsl,p1022-pcie";
- device_type = "pci";
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
reg = <0xf 0xffe0a000 0 0x1000>;
- bus-range = <0 255>;
ranges = <0x2000000 0x0 0xc0000000 0xc 0x40000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0xf 0xffc20000 0x0 0x10000>;
- clock-frequency = <33333333>;
- interrupts = <16 2 0 0>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0 0 1 &mpic 0 1
- 0000 0 0 2 &mpic 1 1
- 0000 0 0 3 &mpic 2 1
- 0000 0 0 4 &mpic 3 1
- >;
pcie@0 {
reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
ranges = <0x2000000 0x0 0xe0000000
0x2000000 0x0 0xe0000000
0x0 0x20000000
@@ -619,32 +237,11 @@
};
};
-
pci2: pcie@fffe0b000 {
- compatible = "fsl,p1022-pcie";
- device_type = "pci";
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
reg = <0xf 0xffe0b000 0 0x1000>;
- bus-range = <0 255>;
ranges = <0x2000000 0x0 0x80000000 0xc 0x00000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0xf 0xffc00000 0x0 0x10000>;
- clock-frequency = <33333333>;
- interrupts = <16 2 0 0>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0 0 1 &mpic 8 1
- 0000 0 0 2 &mpic 9 1
- 0000 0 0 3 &mpic 10 1
- 0000 0 0 4 &mpic 11 1
- >;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
ranges = <0x2000000 0x0 0xe0000000
0x2000000 0x0 0xe0000000
0x0 0x20000000
@@ -655,3 +252,5 @@
};
};
};
+
+/include/ "fsl/p1022si-post.dtsi"
--
1.7.3.4
^ permalink raw reply related
* [PATCH 20/29] powerpc/85xx: Rework P1021MDS device tree
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-19-git-send-email-galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
moved PCI device IRQs down to virtual bridge level
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Added usb node for 2nd usb controller
* Dropping "fsl,p1021-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/fsl/p1021si-post.dtsi | 225 ++++++++++++++
arch/powerpc/boot/dts/fsl/p1021si-pre.dtsi | 68 +++++
arch/powerpc/boot/dts/p1021mds.dts | 421 ++-------------------------
3 files changed, 314 insertions(+), 400 deletions(-)
create mode 100644 arch/powerpc/boot/dts/fsl/p1021si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/p1021si-pre.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/p1021si-post.dtsi b/arch/powerpc/boot/dts/fsl/p1021si-post.dtsi
new file mode 100644
index 0000000..38ba54d
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p1021si-post.dtsi
@@ -0,0 +1,225 @@
+/*
+ * P1021/P1012 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,p1021-elbc", "fsl,elbc", "simple-bus";
+ interrupts = <19 2 0 0>;
+};
+
+/* controller at 0x9000 */
+&pci0 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 0 0>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x4 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x5 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0x6 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0x7 0x1 0x0 0x0
+ >;
+ };
+};
+
+/* controller at 0xa000 */
+&pci1 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 0 0>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+ >;
+ };
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "fsl,p1021-immr", "simple-bus";
+ bus-frequency = <0>; // Filled out by uboot.
+
+ ecm-law@0 {
+ compatible = "fsl,ecm-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <12>;
+ };
+
+ ecm@1000 {
+ compatible = "fsl,p1021-ecm", "fsl,ecm";
+ reg = <0x1000 0x1000>;
+ interrupts = <16 2 0 0>;
+ };
+
+ memory-controller@2000 {
+ compatible = "fsl,p1021-memory-controller";
+ reg = <0x2000 0x1000>;
+ interrupts = <16 2 0 0>;
+ };
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-duart-0.dtsi"
+
+/include/ "pq3-espi-0.dtsi"
+ spi@7000 {
+ fsl,espi-num-chipselects = <4>;
+ };
+
+/include/ "pq3-gpio-0.dtsi"
+
+ L2: l2-cache-controller@20000 {
+ compatible = "fsl,p1021-l2-cache-controller";
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x40000>; // L2,256K
+ interrupts = <16 2 0 0>;
+ };
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-usb2-dr-0.dtsi"
+
+/include/ "pq3-esdhc-0.dtsi"
+/include/ "pq3-sec3.3-0.dtsi"
+
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-mpic-timer-B.dtsi"
+
+/include/ "pq3-etsec2-0.dtsi"
+ enet0: enet0_grp2: ethernet@b0000 {
+ };
+
+/include/ "pq3-etsec2-1.dtsi"
+ enet1: enet1_grp2: ethernet@b1000 {
+ };
+
+/include/ "pq3-etsec2-2.dtsi"
+ enet2: enet2_grp2: ethernet@b2000 {
+ };
+
+ global-utilities@e0000 {
+ compatible = "fsl,p1021-guts";
+ reg = <0xe0000 0x1000>;
+ fsl,has-rstcr;
+ };
+};
+
+&qe {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "qe";
+ compatible = "fsl,qe";
+ fsl,qe-num-riscs = <1>;
+ fsl,qe-num-snums = <28>;
+
+ qeic: interrupt-controller@80 {
+ interrupt-controller;
+ compatible = "fsl,qe-ic";
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ reg = <0x80 0x80>;
+ interrupts = <63 2 0 0 60 2 0 0>; //high:47 low:44
+ };
+
+ ucc@2000 {
+ cell-index = <1>;
+ reg = <0x2000 0x200>;
+ interrupts = <32>;
+ interrupt-parent = <&qeic>;
+ };
+
+ mdio@2120 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2120 0x18>;
+ compatible = "fsl,ucc-mdio";
+ };
+
+ ucc@2400 {
+ cell-index = <5>;
+ reg = <0x2400 0x200>;
+ interrupts = <40>;
+ interrupt-parent = <&qeic>;
+ };
+
+ muram@10000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,qe-muram", "fsl,cpm-muram";
+ ranges = <0x0 0x10000 0x6000>;
+
+ data-only@0 {
+ compatible = "fsl,qe-muram-data",
+ "fsl,cpm-muram-data";
+ reg = <0x0 0x6000>;
+ };
+ };
+};
+
+/include/ "pq3-etsec2-grp2-0.dtsi"
+/include/ "pq3-etsec2-grp2-1.dtsi"
+/include/ "pq3-etsec2-grp2-2.dtsi"
diff --git a/arch/powerpc/boot/dts/fsl/p1021si-pre.dtsi b/arch/powerpc/boot/dts/fsl/p1021si-pre.dtsi
new file mode 100644
index 0000000..4abd54b
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p1021si-pre.dtsi
@@ -0,0 +1,68 @@
+/*
+ * P1021/P1012 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+ compatible = "fsl,P1021";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,P1021@0 {
+ device_type = "cpu";
+ reg = <0x0>;
+ next-level-cache = <&L2>;
+ };
+
+ PowerPC,P1021@1 {
+ device_type = "cpu";
+ reg = <0x1>;
+ next-level-cache = <&L2>;
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p1021mds.dts b/arch/powerpc/boot/dts/p1021mds.dts
index ad5b852..b1bef1f 100644
--- a/arch/powerpc/boot/dts/p1021mds.dts
+++ b/arch/powerpc/boot/dts/p1021mds.dts
@@ -9,53 +9,22 @@
* option) any later version.
*/
-/dts-v1/;
+/include/ "fsl/p1021si-pre.dtsi"
/ {
model = "fsl,P1021";
compatible = "fsl,P1021MDS";
- #address-cells = <2>;
- #size-cells = <2>;
aliases {
- serial0 = &serial0;
- serial1 = &serial1;
- ethernet0 = &enet0;
- ethernet1 = &enet1;
- ethernet2 = &enet2;
ethernet3 = &enet3;
ethernet4 = &enet4;
- pci0 = &pci0;
- pci1 = &pci1;
- };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- PowerPC,P1021@0 {
- device_type = "cpu";
- reg = <0x0>;
- next-level-cache = <&L2>;
- };
-
- PowerPC,P1021@1 {
- device_type = "cpu";
- reg = <0x1>;
- next-level-cache = <&L2>;
- };
};
memory {
device_type = "memory";
};
- localbus@ffe05000 {
- #address-cells = <2>;
- #size-cells = <1>;
- compatible = "fsl,p1021-elbc", "fsl,elbc", "simple-bus";
- reg = <0 0xffe05000 0 0x1000>;
- interrupts = <19 2>;
- interrupt-parent = <&mpic>;
+ lbc: localbus@ffe05000 {
+ reg = <0x0 0xffe05000 0x0 0x1000>;
/* NAND Flash, BCSR, PMC0/1*/
ranges = <0x0 0x0 0x0 0xfc000000 0x02000000
@@ -138,99 +107,26 @@
};
};
- soc@ffe00000 {
-
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "soc";
+ soc: soc@ffe00000 {
compatible = "fsl,p1021-immr", "simple-bus";
- ranges = <0x0 0x0 0xffe00000 0x100000>;
- bus-frequency = <0>; // Filled out by uboot.
-
- ecm-law@0 {
- compatible = "fsl,ecm-law";
- reg = <0x0 0x1000>;
- fsl,num-laws = <12>;
- };
-
- ecm@1000 {
- compatible = "fsl,p1021-ecm", "fsl,ecm";
- reg = <0x1000 0x1000>;
- interrupts = <16 2>;
- interrupt-parent = <&mpic>;
- };
-
- memory-controller@2000 {
- compatible = "fsl,p1021-memory-controller";
- reg = <0x2000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- };
+ ranges = <0x0 0x0 0xffe00000 0x100000>;
i2c@3000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x3000 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
- dfsrr;
rtc@68 {
compatible = "dallas,ds1374";
reg = <0x68>;
};
};
- i2c@3100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- compatible = "fsl-i2c";
- reg = <0x3100 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
- dfsrr;
- };
-
- serial0: serial@4500 {
- cell-index = <0>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4500 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2>;
- interrupt-parent = <&mpic>;
- };
-
- serial1: serial@4600 {
- cell-index = <1>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4600 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2>;
- interrupt-parent = <&mpic>;
- };
-
spi@7000 {
- cell-index = <0>;
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,espi";
- reg = <0x7000 0x1000>;
- interrupts = <59 0x2>;
- interrupt-parent = <&mpic>;
- espi,num-ss-bits = <4>;
- mode = "cpu";
-
- fsl_m25p80@0 {
+
+ flash@0 {
#address-cells = <1>;
#size-cells = <1>;
- compatible = "fsl,espi-flash";
+ compatible = "spansion,s25sl12801";
reg = <0>;
- linux,modalias = "fsl_m25p80";
spi-max-frequency = <40000000>; /* input clock */
+
partition@u-boot {
label = "u-boot-spi";
reg = <0x00000000 0x00100000>;
@@ -253,237 +149,45 @@
};
};
- gpio: gpio-controller@f000 {
- #gpio-cells = <2>;
- compatible = "fsl,mpc8572-gpio";
- reg = <0xf000 0x100>;
- interrupts = <47 0x2>;
- interrupt-parent = <&mpic>;
- gpio-controller;
- };
-
- L2: l2-cache-controller@20000 {
- compatible = "fsl,p1021-l2-cache-controller";
- reg = <0x20000 0x1000>;
- cache-line-size = <32>; // 32 bytes
- cache-size = <0x40000>; // L2,256K
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- };
-
- dma@21300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,eloplus-dma";
- reg = <0x21300 0x4>;
- ranges = <0x0 0x21100 0x200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <20 2>;
- };
- dma-channel@80 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupt-parent = <&mpic>;
- interrupts = <21 2>;
- };
- dma-channel@100 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupt-parent = <&mpic>;
- interrupts = <22 2>;
- };
- dma-channel@180 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupt-parent = <&mpic>;
- interrupts = <23 2>;
- };
- };
-
usb@22000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl-usb2-dr";
- reg = <0x22000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <28 0x2>;
phy_type = "ulpi";
};
- mdio@24000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,etsec2-mdio";
- reg = <0x24000 0x1000 0xb0030 0x4>;
-
+ mdio@24000 {
phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <1 1>;
+ interrupts = <1 1 0 0>;
reg = <0x0>;
};
phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <2 1>;
+ interrupts = <2 1 0 0>;
reg = <0x1>;
};
phy4: ethernet-phy@4 {
- interrupt-parent = <&mpic>;
reg = <0x4>;
};
};
mdio@25000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,etsec2-tbi";
- reg = <0x25000 0x1000 0xb1030 0x4>;
tbi0: tbi-phy@11 {
reg = <0x11>;
device_type = "tbi-phy";
};
};
- enet0: ethernet@B0000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <0>;
- device_type = "network";
- model = "eTSEC";
- compatible = "fsl,etsec2";
- fsl,num_rx_queues = <0x8>;
- fsl,num_tx_queues = <0x8>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupt-parent = <&mpic>;
+ ethernet@b0000 {
phy-handle = <&phy0>;
phy-connection-type = "rgmii-id";
- queue-group@0{
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xB0000 0x1000>;
- interrupts = <29 2 30 2 34 2>;
- };
- queue-group@1{
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xB4000 0x1000>;
- interrupts = <17 2 18 2 24 2>;
- };
};
- enet1: ethernet@B1000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <0>;
- device_type = "network";
- model = "eTSEC";
- compatible = "fsl,etsec2";
- fsl,num_rx_queues = <0x8>;
- fsl,num_tx_queues = <0x8>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupt-parent = <&mpic>;
+ ethernet@b1000 {
phy-handle = <&phy4>;
tbi-handle = <&tbi0>;
phy-connection-type = "sgmii";
- queue-group@0{
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xB1000 0x1000>;
- interrupts = <35 2 36 2 40 2>;
- };
- queue-group@1{
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xB5000 0x1000>;
- interrupts = <51 2 52 2 67 2>;
- };
};
- enet2: ethernet@B2000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <0>;
- device_type = "network";
- model = "eTSEC";
- compatible = "fsl,etsec2";
- fsl,num_rx_queues = <0x8>;
- fsl,num_tx_queues = <0x8>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupt-parent = <&mpic>;
+ ethernet@b2000 {
phy-handle = <&phy1>;
phy-connection-type = "rgmii-id";
- queue-group@0{
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xB2000 0x1000>;
- interrupts = <31 2 32 2 33 2>;
- };
- queue-group@1{
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xB6000 0x1000>;
- interrupts = <25 2 26 2 27 2>;
- };
- };
-
- sdhci@2e000 {
- compatible = "fsl,p1021-esdhc", "fsl,esdhc";
- reg = <0x2e000 0x1000>;
- interrupts = <72 0x2>;
- interrupt-parent = <&mpic>;
- /* Filled in by U-Boot */
- clock-frequency = <0>;
- };
-
- crypto@30000 {
- compatible = "fsl,sec3.3", "fsl,sec3.1",
- "fsl,sec3.0", "fsl,sec2.4",
- "fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0";
- reg = <0x30000 0x10000>;
- interrupts = <45 2 58 2>;
- interrupt-parent = <&mpic>;
- fsl,num-channels = <4>;
- fsl,channel-fifo-len = <24>;
- fsl,exec-units-mask = <0x97c>;
- fsl,descriptor-types-mask = <0x3a30abf>;
- };
-
- mpic: pic@40000 {
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <2>;
- reg = <0x40000 0x40000>;
- compatible = "chrp,open-pic";
- device_type = "open-pic";
- };
-
- msi@41600 {
- compatible = "fsl,p1021-msi", "fsl,mpic-msi";
- reg = <0x41600 0x80>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe0 0
- 0xe1 0
- 0xe2 0
- 0xe3 0
- 0xe4 0
- 0xe5 0
- 0xe6 0
- 0xe7 0>;
- interrupt-parent = <&mpic>;
- };
-
- global-utilities@e0000 { //global utilities block
- compatible = "fsl,p1021-guts";
- reg = <0xe0000 0x1000>;
- fsl,has-rstcr;
};
par_io@e0100 {
@@ -499,8 +203,7 @@
0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */
0x0 0x17 0x2 0x0 0x2 0x0 /* CLK12 */
- 0x0 0x18 0x2 0x0 0x1 0x0 /* CLK9
-*/
+ 0x0 0x18 0x2 0x0 0x1 0x0 /* CLK9 */
0x0 0x7 0x1 0x0 0x2 0x0 /* ENET1_TXD0_SER1_TXD0 */
0x0 0x9 0x1 0x0 0x2 0x0 /* ENET1_TXD1_SER1_TXD1 */
0x0 0xb 0x1 0x0 0x2 0x0 /* ENET1_TXD2_SER1_TXD2 */
@@ -535,31 +238,10 @@
};
pci0: pcie@ffe09000 {
- compatible = "fsl,mpc8548-pcie";
- device_type = "pci";
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
reg = <0 0xffe09000 0 0x1000>;
- bus-range = <0 255>;
ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
- clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0 0 1 &mpic 4 1
- 0000 0 0 2 &mpic 5 1
- 0000 0 0 3 &mpic 6 1
- 0000 0 0 4 &mpic 7 1
- >;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
ranges = <0x2000000 0x0 0xa0000000
0x2000000 0x0 0xa0000000
0x0 0x20000000
@@ -571,31 +253,10 @@
};
pci1: pcie@ffe0a000 {
- compatible = "fsl,mpc8548-pcie";
- device_type = "pci";
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
reg = <0 0xffe0a000 0 0x1000>;
- bus-range = <0 255>;
ranges = <0x2000000 0x0 0xc0000000 0 0xc0000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc20000 0x0 0x10000>;
- clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0 0 1 &mpic 0 1
- 0000 0 0 2 &mpic 1 1
- 0000 0 0 3 &mpic 2 1
- 0000 0 0 4 &mpic 3 1
- >;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
ranges = <0x2000000 0x0 0xc0000000
0x2000000 0x0 0xc0000000
0x0 0x20000000
@@ -606,36 +267,16 @@
};
};
- qe@ffe80000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "qe";
- compatible = "fsl,qe";
+ qe: qe@ffe80000 {
ranges = <0x0 0x0 0xffe80000 0x40000>;
reg = <0 0xffe80000 0 0x480>;
brg-frequency = <0>;
bus-frequency = <0>;
- fsl,qe-num-riscs = <1>;
- fsl,qe-num-snums = <28>;
status = "disabled"; /* no firmware loaded */
- qeic: interrupt-controller@80 {
- interrupt-controller;
- compatible = "fsl,qe-ic";
- #address-cells = <0>;
- #interrupt-cells = <1>;
- reg = <0x80 0x80>;
- interrupts = <63 2 60 2>; //high:47 low:44
- interrupt-parent = <&mpic>;
- };
-
enet3: ucc@2000 {
device_type = "network";
compatible = "ucc_geth";
- cell-index = <1>;
- reg = <0x2000 0x200>;
- interrupts = <32>;
- interrupt-parent = <&qeic>;
local-mac-address = [ 00 00 00 00 00 00 ];
rx-clock-name = "clk12";
tx-clock-name = "clk9";
@@ -645,20 +286,15 @@
};
mdio@2120 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x2120 0x18>;
- compatible = "fsl,ucc-mdio";
-
qe_phy0: ethernet-phy@0 {
interrupt-parent = <&mpic>;
- interrupts = <4 1>;
+ interrupts = <4 1 0 0>;
reg = <0x0>;
device_type = "ethernet-phy";
};
qe_phy1: ethernet-phy@03 {
interrupt-parent = <&mpic>;
- interrupts = <5 1>;
+ interrupts = <5 1 0 0>;
reg = <0x3>;
device_type = "ethernet-phy";
};
@@ -671,10 +307,6 @@
enet4: ucc@2400 {
device_type = "network";
compatible = "ucc_geth";
- cell-index = <5>;
- reg = <0x2400 0x200>;
- interrupts = <40>;
- interrupt-parent = <&qeic>;
local-mac-address = [ 00 00 00 00 00 00 ];
rx-clock-name = "none";
tx-clock-name = "clk13";
@@ -682,18 +314,7 @@
phy-handle = <&qe_phy1>;
phy-connection-type = "rmii";
};
-
- muram@10000 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,qe-muram", "fsl,cpm-muram";
- ranges = <0x0 0x10000 0x6000>;
-
- data-only@0 {
- compatible = "fsl,qe-muram-data",
- "fsl,cpm-muram-data";
- reg = <0x0 0x6000>;
- };
- };
};
};
+
+/include/ "fsl/p1021si-post.dtsi"
--
1.7.3.4
^ permalink raw reply related
* [PATCH 19/29] powerpc/85xx: Add P1020RDB 36-bit address map device tree
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-18-git-send-email-galak@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/p1020rdb_36b.dts | 66 ++++++++++++++++++++++++++++++++
1 files changed, 66 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/boot/dts/p1020rdb_36b.dts
diff --git a/arch/powerpc/boot/dts/p1020rdb_36b.dts b/arch/powerpc/boot/dts/p1020rdb_36b.dts
new file mode 100644
index 0000000..bdbdb60
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020rdb_36b.dts
@@ -0,0 +1,66 @@
+/*
+ * P1020 RDB Device Tree Source (36-bit address map)
+ *
+ * Copyright 2009-2011 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/include/ "fsl/p1020si-pre.dtsi"
+/ {
+ model = "fsl,P1020RDB";
+ compatible = "fsl,P1020RDB";
+
+ memory {
+ device_type = "memory";
+ };
+
+ board_lbc: lbc: localbus@fffe05000 {
+ reg = <0xf 0xffe05000 0 0x1000>;
+
+ /* NOR, NAND Flashes and Vitesse 5 port L2 switch */
+ ranges = <0x0 0x0 0xf 0xef000000 0x01000000
+ 0x1 0x0 0xf 0xffa00000 0x00040000
+ 0x2 0x0 0xf 0xffb00000 0x00020000>;
+ };
+
+ board_soc: soc: soc@fffe00000 {
+ ranges = <0x0 0xf 0xffe00000 0x100000>;
+ };
+
+ pci0: pcie@fffe09000 {
+ reg = <0xf 0xffe09000 0 0x1000>;
+ ranges = <0x2000000 0x0 0xc0000000 0xc 0x20000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0xf 0xffc10000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0xc0000000
+ 0x2000000 0x0 0xc0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci1: pcie@fffe0a000 {
+ reg = <0xf 0xffe0a000 0 0x1000>;
+ ranges = <0x2000000 0x0 0x80000000 0xc 0x00000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0xf 0xffc00000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0x80000000
+ 0x2000000 0x0 0x80000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+};
+
+/include/ "p1020rdb.dtsi"
+/include/ "fsl/p1020si-post.dtsi"
--
1.7.3.4
^ permalink raw reply related
* [PATCH 18/29] powerpc/85xx: Rework P1020RDB device tree
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-17-git-send-email-galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Dropping "fsl,p1020-IP..." from compatibles for standard blocks
* Fixed PCIe interrupt-maps to have proper number of cells
* Added mdio node for etsec@26000
* Added usb node for 2nd usb controller
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/fsl/p1020si-post.dtsi | 174 ++++++++++++
arch/powerpc/boot/dts/fsl/p1020si-pre.dtsi | 68 +++++
arch/powerpc/boot/dts/p1020rdb.dts | 232 +---------------
arch/powerpc/boot/dts/p1020rdb.dtsi | 242 ++++++++++++++++
arch/powerpc/boot/dts/p1020si.dtsi | 407 ---------------------------
5 files changed, 492 insertions(+), 631 deletions(-)
create mode 100644 arch/powerpc/boot/dts/fsl/p1020si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/p1020si-pre.dtsi
create mode 100644 arch/powerpc/boot/dts/p1020rdb.dtsi
delete mode 100644 arch/powerpc/boot/dts/p1020si.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/p1020si-post.dtsi b/arch/powerpc/boot/dts/fsl/p1020si-post.dtsi
new file mode 100644
index 0000000..fc924c5
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p1020si-post.dtsi
@@ -0,0 +1,174 @@
+/*
+ * P1020/P1011 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,p1020-elbc", "fsl,elbc", "simple-bus";
+ interrupts = <19 2 0 0>;
+};
+
+/* controller at 0x9000 */
+&pci0 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 0 0>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x4 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x5 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0x6 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0x7 0x1 0x0 0x0
+ >;
+ };
+};
+
+/* controller at 0xa000 */
+&pci1 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 0 0>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+ >;
+ };
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "fsl,p1020-immr", "simple-bus";
+ bus-frequency = <0>; // Filled out by uboot.
+
+ ecm-law@0 {
+ compatible = "fsl,ecm-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <12>;
+ };
+
+ ecm@1000 {
+ compatible = "fsl,p1020-ecm", "fsl,ecm";
+ reg = <0x1000 0x1000>;
+ interrupts = <16 2 0 0>;
+ };
+
+ memory-controller@2000 {
+ compatible = "fsl,p1020-memory-controller";
+ reg = <0x2000 0x1000>;
+ interrupts = <16 2 0 0>;
+ };
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-duart-0.dtsi"
+
+/include/ "pq3-espi-0.dtsi"
+ spi@7000 {
+ fsl,espi-num-chipselects = <4>;
+ };
+
+/include/ "pq3-gpio-0.dtsi"
+
+ L2: l2-cache-controller@20000 {
+ compatible = "fsl,p1020-l2-cache-controller";
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x40000>; // L2,256K
+ interrupts = <16 2 0 0>;
+ };
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-usb2-dr-0.dtsi"
+/include/ "pq3-usb2-dr-1.dtsi"
+
+/include/ "pq3-esdhc-0.dtsi"
+/include/ "pq3-sec3.3-0.dtsi"
+
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-mpic-timer-B.dtsi"
+
+/include/ "pq3-etsec2-0.dtsi"
+ enet0: enet0_grp2: ethernet@b0000 {
+ };
+
+/include/ "pq3-etsec2-1.dtsi"
+ enet1: enet1_grp2: ethernet@b1000 {
+ };
+
+/include/ "pq3-etsec2-2.dtsi"
+ enet2: enet2_grp2: ethernet@b2000 {
+ };
+
+ global-utilities@e0000 {
+ compatible = "fsl,p1020-guts";
+ reg = <0xe0000 0x1000>;
+ fsl,has-rstcr;
+ };
+};
+
+/include/ "pq3-etsec2-grp2-0.dtsi"
+/include/ "pq3-etsec2-grp2-1.dtsi"
+/include/ "pq3-etsec2-grp2-2.dtsi"
diff --git a/arch/powerpc/boot/dts/fsl/p1020si-pre.dtsi b/arch/powerpc/boot/dts/fsl/p1020si-pre.dtsi
new file mode 100644
index 0000000..6f0376e
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p1020si-pre.dtsi
@@ -0,0 +1,68 @@
+/*
+ * P1020/P1011 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+ compatible = "fsl,P1020";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,P1020@0 {
+ device_type = "cpu";
+ reg = <0x0>;
+ next-level-cache = <&L2>;
+ };
+
+ PowerPC,P1020@1 {
+ device_type = "cpu";
+ reg = <0x1>;
+ next-level-cache = <&L2>;
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p1020rdb.dts b/arch/powerpc/boot/dts/p1020rdb.dts
index b31e7ec..518bf99 100644
--- a/arch/powerpc/boot/dts/p1020rdb.dts
+++ b/arch/powerpc/boot/dts/p1020rdb.dts
@@ -9,245 +9,26 @@
* option) any later version.
*/
-/include/ "p1020si.dtsi"
-
+/include/ "fsl/p1020si-pre.dtsi"
/ {
model = "fsl,P1020RDB";
compatible = "fsl,P1020RDB";
- aliases {
- serial0 = &serial0;
- serial1 = &serial1;
- ethernet0 = &enet0;
- ethernet1 = &enet1;
- ethernet2 = &enet2;
- pci0 = &pci0;
- pci1 = &pci1;
- };
-
memory {
device_type = "memory";
};
- localbus@ffe05000 {
+ board_lbc: lbc: localbus@ffe05000 {
+ reg = <0 0xffe05000 0 0x1000>;
/* NOR, NAND Flashes and Vitesse 5 port L2 switch */
ranges = <0x0 0x0 0x0 0xef000000 0x01000000
0x1 0x0 0x0 0xffa00000 0x00040000
0x2 0x0 0x0 0xffb00000 0x00020000>;
-
- nor@0,0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "cfi-flash";
- reg = <0x0 0x0 0x1000000>;
- bank-width = <2>;
- device-width = <1>;
-
- partition@0 {
- /* This location must not be altered */
- /* 256KB for Vitesse 7385 Switch firmware */
- reg = <0x0 0x00040000>;
- label = "NOR (RO) Vitesse-7385 Firmware";
- read-only;
- };
-
- partition@40000 {
- /* 256KB for DTB Image */
- reg = <0x00040000 0x00040000>;
- label = "NOR (RO) DTB Image";
- read-only;
- };
-
- partition@80000 {
- /* 3.5 MB for Linux Kernel Image */
- reg = <0x00080000 0x00380000>;
- label = "NOR (RO) Linux Kernel Image";
- read-only;
- };
-
- partition@400000 {
- /* 11MB for JFFS2 based Root file System */
- reg = <0x00400000 0x00b00000>;
- label = "NOR (RW) JFFS2 Root File System";
- };
-
- partition@f00000 {
- /* This location must not be altered */
- /* 512KB for u-boot Bootloader Image */
- /* 512KB for u-boot Environment Variables */
- reg = <0x00f00000 0x00100000>;
- label = "NOR (RO) U-Boot Image";
- read-only;
- };
- };
-
- nand@1,0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,p1020-fcm-nand",
- "fsl,elbc-fcm-nand";
- reg = <0x1 0x0 0x40000>;
-
- partition@0 {
- /* This location must not be altered */
- /* 1MB for u-boot Bootloader Image */
- reg = <0x0 0x00100000>;
- label = "NAND (RO) U-Boot Image";
- read-only;
- };
-
- partition@100000 {
- /* 1MB for DTB Image */
- reg = <0x00100000 0x00100000>;
- label = "NAND (RO) DTB Image";
- read-only;
- };
-
- partition@200000 {
- /* 4MB for Linux Kernel Image */
- reg = <0x00200000 0x00400000>;
- label = "NAND (RO) Linux Kernel Image";
- read-only;
- };
-
- partition@600000 {
- /* 4MB for Compressed Root file System Image */
- reg = <0x00600000 0x00400000>;
- label = "NAND (RO) Compressed RFS Image";
- read-only;
- };
-
- partition@a00000 {
- /* 7MB for JFFS2 based Root file System */
- reg = <0x00a00000 0x00700000>;
- label = "NAND (RW) JFFS2 Root File System";
- };
-
- partition@1100000 {
- /* 15MB for JFFS2 based Root file System */
- reg = <0x01100000 0x00f00000>;
- label = "NAND (RW) Writable User area";
- };
- };
-
- L2switch@2,0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "vitesse-7385";
- reg = <0x2 0x0 0x20000>;
- };
-
};
- soc@ffe00000 {
- i2c@3000 {
- rtc@68 {
- compatible = "dallas,ds1339";
- reg = <0x68>;
- };
- };
-
- spi@7000 {
- flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "spansion,s25sl12801";
- reg = <0>;
- spi-max-frequency = <40000000>; /* input clock */
-
- partition@u-boot {
- /* 512KB for u-boot Bootloader Image */
- reg = <0x0 0x00080000>;
- label = "u-boot";
- read-only;
- };
-
- partition@dtb {
- /* 512KB for DTB Image */
- reg = <0x00080000 0x00080000>;
- label = "dtb";
- read-only;
- };
-
- partition@kernel {
- /* 4MB for Linux Kernel Image */
- reg = <0x00100000 0x00400000>;
- label = "kernel";
- read-only;
- };
-
- partition@fs {
- /* 4MB for Compressed RFS Image */
- reg = <0x00500000 0x00400000>;
- label = "file system";
- read-only;
- };
-
- partition@jffs-fs {
- /* 7MB for JFFS2 based RFS */
- reg = <0x00900000 0x00700000>;
- label = "file system jffs2";
- };
- };
- };
-
- mdio@24000 {
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <3 1>;
- reg = <0x0>;
- };
-
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <2 1>;
- reg = <0x1>;
- };
- };
-
- mdio@25000 {
-
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- enet0: ethernet@b0000 {
- fixed-link = <1 1 1000 0 0>;
- phy-connection-type = "rgmii-id";
-
- };
-
- enet1: ethernet@b1000 {
- phy-handle = <&phy0>;
- tbi-handle = <&tbi0>;
- phy-connection-type = "sgmii";
-
- };
-
- enet2: ethernet@b2000 {
- phy-handle = <&phy1>;
- phy-connection-type = "rgmii-id";
-
- };
-
- usb@22000 {
- phy_type = "ulpi";
- };
-
- /* USB2 is shared with localbus, so it must be disabled
- by default. We can't put 'status = "disabled";' here
- since U-Boot doesn't clear the status property when
- it enables USB2. OTOH, U-Boot does create a new node
- when there isn't any. So, just comment it out.
- usb@23000 {
- phy_type = "ulpi";
- };
- */
-
+ board_soc: soc: soc@ffe00000 {
+ ranges = <0x0 0x0 0xffe00000 0x100000>;
};
pci0: pcie@ffe09000 {
@@ -280,3 +61,6 @@
};
};
};
+
+/include/ "p1020rdb.dtsi"
+/include/ "fsl/p1020si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p1020rdb.dtsi b/arch/powerpc/boot/dts/p1020rdb.dtsi
new file mode 100644
index 0000000..3738946
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020rdb.dtsi
@@ -0,0 +1,242 @@
+/*
+ * P1020 RDB Device Tree Source stub (no addresses or top-level ranges)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&board_lbc {
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x1000000>;
+ bank-width = <2>;
+ device-width = <1>;
+
+ partition@0 {
+ /* This location must not be altered */
+ /* 256KB for Vitesse 7385 Switch firmware */
+ reg = <0x0 0x00040000>;
+ label = "NOR (RO) Vitesse-7385 Firmware";
+ read-only;
+ };
+
+ partition@40000 {
+ /* 256KB for DTB Image */
+ reg = <0x00040000 0x00040000>;
+ label = "NOR (RO) DTB Image";
+ read-only;
+ };
+
+ partition@80000 {
+ /* 3.5 MB for Linux Kernel Image */
+ reg = <0x00080000 0x00380000>;
+ label = "NOR (RO) Linux Kernel Image";
+ read-only;
+ };
+
+ partition@400000 {
+ /* 11MB for JFFS2 based Root file System */
+ reg = <0x00400000 0x00b00000>;
+ label = "NOR (RW) JFFS2 Root File System";
+ };
+
+ partition@f00000 {
+ /* This location must not be altered */
+ /* 512KB for u-boot Bootloader Image */
+ /* 512KB for u-boot Environment Variables */
+ reg = <0x00f00000 0x00100000>;
+ label = "NOR (RO) U-Boot Image";
+ read-only;
+ };
+ };
+
+ nand@1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,p1020-fcm-nand",
+ "fsl,elbc-fcm-nand";
+ reg = <0x1 0x0 0x40000>;
+
+ partition@0 {
+ /* This location must not be altered */
+ /* 1MB for u-boot Bootloader Image */
+ reg = <0x0 0x00100000>;
+ label = "NAND (RO) U-Boot Image";
+ read-only;
+ };
+
+ partition@100000 {
+ /* 1MB for DTB Image */
+ reg = <0x00100000 0x00100000>;
+ label = "NAND (RO) DTB Image";
+ read-only;
+ };
+
+ partition@200000 {
+ /* 4MB for Linux Kernel Image */
+ reg = <0x00200000 0x00400000>;
+ label = "NAND (RO) Linux Kernel Image";
+ read-only;
+ };
+
+ partition@600000 {
+ /* 4MB for Compressed Root file System Image */
+ reg = <0x00600000 0x00400000>;
+ label = "NAND (RO) Compressed RFS Image";
+ read-only;
+ };
+
+ partition@a00000 {
+ /* 7MB for JFFS2 based Root file System */
+ reg = <0x00a00000 0x00700000>;
+ label = "NAND (RW) JFFS2 Root File System";
+ };
+
+ partition@1100000 {
+ /* 15MB for JFFS2 based Root file System */
+ reg = <0x01100000 0x00f00000>;
+ label = "NAND (RW) Writable User area";
+ };
+ };
+
+ L2switch@2,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "vitesse-7385";
+ reg = <0x2 0x0 0x20000>;
+ };
+};
+
+&board_soc {
+ i2c@3000 {
+ rtc@68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ };
+ };
+
+ spi@7000 {
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25sl12801";
+ reg = <0>;
+ spi-max-frequency = <40000000>; /* input clock */
+
+ partition@u-boot {
+ /* 512KB for u-boot Bootloader Image */
+ reg = <0x0 0x00080000>;
+ label = "u-boot";
+ read-only;
+ };
+
+ partition@dtb {
+ /* 512KB for DTB Image */
+ reg = <0x00080000 0x00080000>;
+ label = "dtb";
+ read-only;
+ };
+
+ partition@kernel {
+ /* 4MB for Linux Kernel Image */
+ reg = <0x00100000 0x00400000>;
+ label = "kernel";
+ read-only;
+ };
+
+ partition@fs {
+ /* 4MB for Compressed RFS Image */
+ reg = <0x00500000 0x00400000>;
+ label = "file system";
+ read-only;
+ };
+
+ partition@jffs-fs {
+ /* 7MB for JFFS2 based RFS */
+ reg = <0x00900000 0x00700000>;
+ label = "file system jffs2";
+ };
+ };
+ };
+
+ usb@22000 {
+ phy_type = "ulpi";
+ };
+
+ /* USB2 is shared with localbus, so it must be disabled
+ by default. We can't put 'status = "disabled";' here
+ since U-Boot doesn't clear the status property when
+ it enables USB2. OTOH, U-Boot does create a new node
+ when there isn't any. So, just comment it out.
+ usb@23000 {
+ phy_type = "ulpi";
+ };
+ */
+
+ mdio@24000 {
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <3 1>;
+ reg = <0x0>;
+ };
+
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <2 1>;
+ reg = <0x1>;
+ };
+ };
+
+ mdio@25000 {
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet0: ethernet@b0000 {
+ fixed-link = <1 1 1000 0 0>;
+ phy-connection-type = "rgmii-id";
+
+ };
+
+ enet1: ethernet@b1000 {
+ phy-handle = <&phy0>;
+ tbi-handle = <&tbi0>;
+ phy-connection-type = "sgmii";
+ };
+
+ enet2: ethernet@b2000 {
+ phy-handle = <&phy1>;
+ phy-connection-type = "rgmii-id";
+ };
+};
diff --git a/arch/powerpc/boot/dts/p1020si.dtsi b/arch/powerpc/boot/dts/p1020si.dtsi
deleted file mode 100644
index b08c848..0000000
--- a/arch/powerpc/boot/dts/p1020si.dtsi
+++ /dev/null
@@ -1,407 +0,0 @@
-/*
- * P1020si Device Tree Source
- *
- * Copyright 2011 Freescale Semiconductor Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-/dts-v1/;
-/ {
- compatible = "fsl,P1020";
- #address-cells = <2>;
- #size-cells = <2>;
- interrupt-parent = <&mpic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- PowerPC,P1020@0 {
- device_type = "cpu";
- reg = <0x0>;
- next-level-cache = <&L2>;
- };
-
- PowerPC,P1020@1 {
- device_type = "cpu";
- reg = <0x1>;
- next-level-cache = <&L2>;
- };
- };
-
- localbus@ffe05000 {
- #address-cells = <2>;
- #size-cells = <1>;
- compatible = "fsl,p1020-elbc", "fsl,elbc", "simple-bus";
- reg = <0 0xffe05000 0 0x1000>;
- interrupts = <19 2 0 0>;
- };
-
- soc@ffe00000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "soc";
- compatible = "fsl,p1020-immr", "simple-bus";
- ranges = <0x0 0x0 0xffe00000 0x100000>;
- bus-frequency = <0>; // Filled out by uboot.
-
- ecm-law@0 {
- compatible = "fsl,ecm-law";
- reg = <0x0 0x1000>;
- fsl,num-laws = <12>;
- };
-
- ecm@1000 {
- compatible = "fsl,p1020-ecm", "fsl,ecm";
- reg = <0x1000 0x1000>;
- interrupts = <16 2 0 0>;
- };
-
- memory-controller@2000 {
- compatible = "fsl,p1020-memory-controller";
- reg = <0x2000 0x1000>;
- interrupts = <16 2 0 0>;
- };
-
- i2c@3000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x3000 0x100>;
- interrupts = <43 2 0 0>;
- dfsrr;
- };
-
- i2c@3100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- compatible = "fsl-i2c";
- reg = <0x3100 0x100>;
- interrupts = <43 2 0 0>;
- dfsrr;
- };
-
- serial0: serial@4500 {
- cell-index = <0>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4500 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2 0 0>;
- };
-
- serial1: serial@4600 {
- cell-index = <1>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4600 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2 0 0>;
- };
-
- spi@7000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,p1020-espi", "fsl,mpc8536-espi";
- reg = <0x7000 0x1000>;
- interrupts = <59 0x2 0 0>;
- fsl,espi-num-chipselects = <4>;
- };
-
- gpio: gpio-controller@f000 {
- #gpio-cells = <2>;
- compatible = "fsl,mpc8572-gpio";
- reg = <0xf000 0x100>;
- interrupts = <47 0x2 0 0>;
- gpio-controller;
- };
-
- L2: l2-cache-controller@20000 {
- compatible = "fsl,p1020-l2-cache-controller";
- reg = <0x20000 0x1000>;
- cache-line-size = <32>; // 32 bytes
- cache-size = <0x40000>; // L2,256K
- interrupts = <16 2 0 0>;
- };
-
- dma@21300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,eloplus-dma";
- reg = <0x21300 0x4>;
- ranges = <0x0 0x21100 0x200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupts = <20 2 0 0>;
- };
- dma-channel@80 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupts = <21 2 0 0>;
- };
- dma-channel@100 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupts = <22 2 0 0>;
- };
- dma-channel@180 {
- compatible = "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupts = <23 2 0 0>;
- };
- };
-
- mdio@24000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,etsec2-mdio";
- reg = <0x24000 0x1000 0xb0030 0x4>;
-
- };
-
- mdio@25000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,etsec2-tbi";
- reg = <0x25000 0x1000 0xb1030 0x4>;
-
- };
-
- enet0: ethernet@b0000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "network";
- model = "eTSEC";
- compatible = "fsl,etsec2";
- fsl,num_rx_queues = <0x8>;
- fsl,num_tx_queues = <0x8>;
- fsl,magic-packet;
- local-mac-address = [ 00 00 00 00 00 00 ];
-
- queue-group@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xb0000 0x1000>;
- interrupts = <29 2 0 0 30 2 0 0 34 2 0 0>;
- };
-
- queue-group@1 {
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xb4000 0x1000>;
- interrupts = <17 2 0 0 18 2 0 0 24 2 0 0>;
- };
- };
-
- enet1: ethernet@b1000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "network";
- model = "eTSEC";
- compatible = "fsl,etsec2";
- fsl,num_rx_queues = <0x8>;
- fsl,num_tx_queues = <0x8>;
- fsl,magic-packet;
- local-mac-address = [ 00 00 00 00 00 00 ];
-
- queue-group@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xb1000 0x1000>;
- interrupts = <35 2 0 0 36 2 0 0 40 2 0 0>;
- };
-
- queue-group@1 {
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xb5000 0x1000>;
- interrupts = <51 2 0 0 52 2 0 0 67 2 0 0>;
- };
- };
-
- enet2: ethernet@b2000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "network";
- model = "eTSEC";
- compatible = "fsl,etsec2";
- fsl,num_rx_queues = <0x8>;
- fsl,num_tx_queues = <0x8>;
- fsl,magic-packet;
- local-mac-address = [ 00 00 00 00 00 00 ];
-
- queue-group@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xb2000 0x1000>;
- interrupts = <31 2 0 0 32 2 0 0 33 2 0 0>;
- };
-
- queue-group@1 {
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xb6000 0x1000>;
- interrupts = <25 2 0 0 26 2 0 0 27 2 0 0>;
- };
- };
-
- usb@22000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl-usb2-dr";
- reg = <0x22000 0x1000>;
- interrupts = <28 0x2 0 0>;
- };
-
- /* USB2 is shared with localbus, so it must be disabled
- by default. We can't put 'status = "disabled";' here
- since U-Boot doesn't clear the status property when
- it enables USB2. OTOH, U-Boot does create a new node
- when there isn't any. So, just comment it out.
- usb@23000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl-usb2-dr";
- reg = <0x23000 0x1000>;
- interrupts = <46 0x2 0 0>;
- phy_type = "ulpi";
- };
- */
-
- sdhci@2e000 {
- compatible = "fsl,p1020-esdhc", "fsl,esdhc";
- reg = <0x2e000 0x1000>;
- interrupts = <72 0x2 0 0>;
- /* Filled in by U-Boot */
- clock-frequency = <0>;
- };
-
- crypto@30000 {
- compatible = "fsl,sec3.3", "fsl,sec3.1", "fsl,sec3.0",
- "fsl,sec2.4", "fsl,sec2.2", "fsl,sec2.1",
- "fsl,sec2.0";
- reg = <0x30000 0x10000>;
- interrupts = <45 2 0 0 58 2 0 0>;
- fsl,num-channels = <4>;
- fsl,channel-fifo-len = <24>;
- fsl,exec-units-mask = <0x97c>;
- fsl,descriptor-types-mask = <0x3a30abf>;
- };
-
- mpic: pic@40000 {
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <4>;
- reg = <0x40000 0x40000>;
- compatible = "chrp,open-pic";
- device_type = "open-pic";
- };
-
- timer@41100 {
- compatible = "fsl,mpic-global-timer";
- reg = <0x41100 0x100 0x41300 4>;
- interrupts = <0 0 3 0
- 1 0 3 0
- 2 0 3 0
- 3 0 3 0>;
- };
-
- timer@42100 {
- compatible = "fsl,mpic-global-timer";
- reg = <0x42100 0x100 0x42300 4>;
- interrupts = <4 0 3 0
- 5 0 3 0
- 6 0 3 0
- 7 0 3 0>;
- };
-
- msi@41600 {
- compatible = "fsl,p1020-msi", "fsl,mpic-msi";
- reg = <0x41600 0x80>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe0 0 0 0
- 0xe1 0 0 0
- 0xe2 0 0 0
- 0xe3 0 0 0
- 0xe4 0 0 0
- 0xe5 0 0 0
- 0xe6 0 0 0
- 0xe7 0 0 0>;
- };
-
- global-utilities@e0000 { //global utilities block
- compatible = "fsl,p1020-guts","fsl,p2020-guts";
- reg = <0xe0000 0x1000>;
- fsl,has-rstcr;
- };
- };
-
- pci0: pcie@ffe09000 {
- compatible = "fsl,mpc8548-pcie";
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
- bus-range = <0 255>;
- clock-frequency = <33333333>;
- interrupts = <16 2 0 0>;
-
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupts = <16 2 0 0>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0x0 0x0 0x1 &mpic 0x4 0x1
- 0000 0x0 0x0 0x2 &mpic 0x5 0x1
- 0000 0x0 0x0 0x3 &mpic 0x6 0x1
- 0000 0x0 0x0 0x4 &mpic 0x7 0x1
- >;
- };
-
- };
-
- pci1: pcie@ffe0a000 {
- compatible = "fsl,mpc8548-pcie";
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
- bus-range = <0 255>;
- clock-frequency = <33333333>;
- interrupts = <16 2 0 0>;
-
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupts = <16 2 0 0>;
- interrupt-map-mask = <0xf800 0 0 7>;
-
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0x0 0x0 0x1 &mpic 0x0 0x1
- 0000 0x0 0x0 0x2 &mpic 0x1 0x1
- 0000 0x0 0x0 0x3 &mpic 0x2 0x1
- 0000 0x0 0x0 0x4 &mpic 0x3 0x1
- >;
- };
- };
-};
--
1.7.3.4
^ permalink raw reply related
* [PATCH 17/29] powerpc/85xx: Add a P1010RDB 36-bit address map device tree
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-16-git-send-email-galak@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/p1010rdb_36b.dts | 89 ++++++++++++++++++++++++++++++++
1 files changed, 89 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/boot/dts/p1010rdb_36b.dts
diff --git a/arch/powerpc/boot/dts/p1010rdb_36b.dts b/arch/powerpc/boot/dts/p1010rdb_36b.dts
new file mode 100644
index 0000000..64776f4
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1010rdb_36b.dts
@@ -0,0 +1,89 @@
+/*
+ * P1010 RDB Device Tree Source (36-bit address map)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/p1010si-pre.dtsi"
+
+/ {
+ model = "fsl,P1010RDB";
+ compatible = "fsl,P1010RDB";
+
+ memory {
+ device_type = "memory";
+ };
+
+ board_ifc: ifc: ifc@fffe1e000 {
+ /* NOR, NAND Flashes and CPLD on board */
+ ranges = <0x0 0x0 0xf 0xee000000 0x02000000
+ 0x1 0x0 0xf 0xff800000 0x00010000
+ 0x3 0x0 0xf 0xffb00000 0x00000020>;
+ reg = <0xf 0xffe1e000 0 0x2000>;
+ };
+
+ board_soc: soc: soc@fffe00000 {
+ ranges = <0x0 0xf 0xffe00000 0x100000>;
+ };
+
+ pci0: pcie@fffe09000 {
+ reg = <0xf 0xffe09000 0 0x1000>;
+ ranges = <0x2000000 0x0 0xc0000000 0xc 0x20000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0xf 0xffc10000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0xc0000000
+ 0x2000000 0x0 0xc0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci1: pcie@fffe0a000 {
+ reg = <0xf 0xffe0a000 0 0x1000>;
+ ranges = <0x2000000 0x0 0xc0000000 0xc 0x20000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0xf 0xffc10000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0xc0000000
+ 0x2000000 0x0 0xc0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+};
+
+/include/ "p1010rdb.dtsi"
+/include/ "fsl/p1010si-post.dtsi"
--
1.7.3.4
^ permalink raw reply related
* [PATCH 16/29] powerpc/85xx: Add crypto engine to P1010 SoC device tree
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-15-git-send-email-galak@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/fsl/p1010si-post.dtsi | 1 +
1 files changed, 1 insertions(+), 0 deletions(-)
diff --git a/arch/powerpc/boot/dts/fsl/p1010si-post.dtsi b/arch/powerpc/boot/dts/fsl/p1010si-post.dtsi
index 75eb921..bd9e163 100644
--- a/arch/powerpc/boot/dts/fsl/p1010si-post.dtsi
+++ b/arch/powerpc/boot/dts/fsl/p1010si-post.dtsi
@@ -161,6 +161,7 @@
fsl,sdhci-auto-cmd12;
};
+/include/ "pq3-sec4.4-0.dtsi"
/include/ "pq3-mpic.dtsi"
/include/ "pq3-mpic-timer-B.dtsi"
--
1.7.3.4
^ permalink raw reply related
* [PATCH 14/29] powerpc/85xx: Rework P1010RDB and P1010 device tree
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-13-git-send-email-galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Dropping "fsl,p1010-IP..." from compatibles for standard blocks
* PCI interrupt map - wrong IRQs for PCI-0 controller
* SDHC interrupt sense was wrong
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/fsl/p1010si-post.dtsi | 197 ++++++++++++++
arch/powerpc/boot/dts/fsl/p1010si-pre.dtsi | 64 +++++
arch/powerpc/boot/dts/p1010rdb.dts | 228 +----------------
arch/powerpc/boot/dts/p1010rdb.dtsi | 222 ++++++++++++++++
arch/powerpc/boot/dts/p1010si.dtsi | 374 ---------------------------
5 files changed, 493 insertions(+), 592 deletions(-)
create mode 100644 arch/powerpc/boot/dts/fsl/p1010si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/p1010si-pre.dtsi
create mode 100644 arch/powerpc/boot/dts/p1010rdb.dtsi
delete mode 100644 arch/powerpc/boot/dts/p1010si.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/p1010si-post.dtsi b/arch/powerpc/boot/dts/fsl/p1010si-post.dtsi
new file mode 100644
index 0000000..75eb921
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p1010si-post.dtsi
@@ -0,0 +1,197 @@
+/*
+ * P1010/P1014 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&ifc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc", "simple-bus";
+ interrupts = <16 2 0 0 19 2 0 0>;
+};
+
+/* controller at 0x9000 */
+&pci0 {
+ compatible = "fsl,p1010-pcie", "fsl,qoriq-pcie-v2.3", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 0 0>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x4 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x5 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0x6 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0x7 0x1 0x0 0x0
+ >;
+ };
+};
+
+/* controller at 0xa000 */
+&pci1 {
+ compatible = "fsl,p1010-pcie", "fsl,qoriq-pcie-v2.3", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 0 0>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+ >;
+ };
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "fsl,p1010-immr", "simple-bus";
+ bus-frequency = <0>; // Filled out by uboot.
+
+ ecm-law@0 {
+ compatible = "fsl,ecm-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <12>;
+ };
+
+ ecm@1000 {
+ compatible = "fsl,p1010-ecm", "fsl,ecm";
+ reg = <0x1000 0x1000>;
+ interrupts = <16 2 0 0>;
+ };
+
+ memory-controller@2000 {
+ compatible = "fsl,p1010-memory-controller";
+ reg = <0x2000 0x1000>;
+ interrupts = <16 2 0 0>;
+ };
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-duart-0.dtsi"
+/include/ "pq3-espi-0.dtsi"
+ spi0: spi@7000 {
+ fsl,espi-num-chipselects = <1>;
+ };
+
+/include/ "pq3-gpio-0.dtsi"
+/include/ "pq3-sata2-0.dtsi"
+/include/ "pq3-sata2-1.dtsi"
+
+ can0: can@1c000 {
+ compatible = "fsl,p1010-flexcan";
+ reg = <0x1c000 0x1000>;
+ interrupts = <48 0x2 0 0>;
+ };
+
+ can1: can@1d000 {
+ compatible = "fsl,p1010-flexcan";
+ reg = <0x1d000 0x1000>;
+ interrupts = <61 0x2 0 0>;
+ };
+
+ L2: l2-cache-controller@20000 {
+ compatible = "fsl,p1010-l2-cache-controller",
+ "fsl,p1014-l2-cache-controller";
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x40000>; // L2,256K
+ interrupts = <16 2 0 0>;
+ };
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-usb2-dr-0.dtsi"
+/include/ "pq3-esdhc-0.dtsi"
+ sdhc@2e000 {
+ fsl,sdhci-auto-cmd12;
+ };
+
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-mpic-timer-B.dtsi"
+
+/include/ "pq3-etsec2-0.dtsi"
+ enet0: ethernet@b0000 {
+ queue-group@b0000 {
+ fsl,rx-bit-map = <0xff>;
+ fsl,tx-bit-map = <0xff>;
+ };
+ };
+
+/include/ "pq3-etsec2-1.dtsi"
+ enet1: ethernet@b1000 {
+ queue-group@b1000 {
+ fsl,rx-bit-map = <0xff>;
+ fsl,tx-bit-map = <0xff>;
+ };
+ };
+
+/include/ "pq3-etsec2-2.dtsi"
+ enet2: ethernet@b2000 {
+ queue-group@b2000 {
+ fsl,rx-bit-map = <0xff>;
+ fsl,tx-bit-map = <0xff>;
+ };
+
+ };
+
+ global-utilities@e0000 {
+ compatible = "fsl,p1010-guts";
+ reg = <0xe0000 0x1000>;
+ fsl,has-rstcr;
+ };
+};
diff --git a/arch/powerpc/boot/dts/fsl/p1010si-pre.dtsi b/arch/powerpc/boot/dts/fsl/p1010si-pre.dtsi
new file mode 100644
index 0000000..7354a8f
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p1010si-pre.dtsi
@@ -0,0 +1,64 @@
+/*
+ * P1010/P1014 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+ compatible = "fsl,P1010";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ can0 = &can0;
+ can1 = &can1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,P1010@0 {
+ device_type = "cpu";
+ reg = <0x0>;
+ next-level-cache = <&L2>;
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p1010rdb.dts b/arch/powerpc/boot/dts/p1010rdb.dts
index d6c669c..b868d22 100644
--- a/arch/powerpc/boot/dts/p1010rdb.dts
+++ b/arch/powerpc/boot/dts/p1010rdb.dts
@@ -9,230 +9,33 @@
* option) any later version.
*/
-/include/ "p1010si.dtsi"
+/include/ "fsl/p1010si-pre.dtsi"
/ {
model = "fsl,P1010RDB";
compatible = "fsl,P1010RDB";
- aliases {
- serial0 = &serial0;
- serial1 = &serial1;
- ethernet0 = &enet0;
- ethernet1 = &enet1;
- ethernet2 = &enet2;
- pci0 = &pci0;
- pci1 = &pci1;
- can0 = &can0;
- can1 = &can1;
- };
-
memory {
device_type = "memory";
};
- ifc@ffe1e000 {
+ board_ifc: ifc: ifc@ffe1e000 {
/* NOR, NAND Flashes and CPLD on board */
ranges = <0x0 0x0 0x0 0xee000000 0x02000000
0x1 0x0 0x0 0xff800000 0x00010000
0x3 0x0 0x0 0xffb00000 0x00000020>;
-
- nor@0,0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "cfi-flash";
- reg = <0x0 0x0 0x2000000>;
- bank-width = <2>;
- device-width = <1>;
-
- partition@40000 {
- /* 256KB for DTB Image */
- reg = <0x00040000 0x00040000>;
- label = "NOR DTB Image";
- };
-
- partition@80000 {
- /* 7 MB for Linux Kernel Image */
- reg = <0x00080000 0x00700000>;
- label = "NOR Linux Kernel Image";
- };
-
- partition@800000 {
- /* 20MB for JFFS2 based Root file System */
- reg = <0x00800000 0x01400000>;
- label = "NOR JFFS2 Root File System";
- };
-
- partition@1f00000 {
- /* This location must not be altered */
- /* 512KB for u-boot Bootloader Image */
- /* 512KB for u-boot Environment Variables */
- reg = <0x01f00000 0x00100000>;
- label = "NOR U-Boot Image";
- read-only;
- };
- };
-
- nand@1,0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,ifc-nand";
- reg = <0x1 0x0 0x10000>;
-
- partition@0 {
- /* This location must not be altered */
- /* 1MB for u-boot Bootloader Image */
- reg = <0x0 0x00100000>;
- label = "NAND U-Boot Image";
- read-only;
- };
-
- partition@100000 {
- /* 1MB for DTB Image */
- reg = <0x00100000 0x00100000>;
- label = "NAND DTB Image";
- };
-
- partition@200000 {
- /* 4MB for Linux Kernel Image */
- reg = <0x00200000 0x00400000>;
- label = "NAND Linux Kernel Image";
- };
-
- partition@600000 {
- /* 4MB for Compressed Root file System Image */
- reg = <0x00600000 0x00400000>;
- label = "NAND Compressed RFS Image";
- };
-
- partition@a00000 {
- /* 15MB for JFFS2 based Root file System */
- reg = <0x00a00000 0x00f00000>;
- label = "NAND JFFS2 Root File System";
- };
-
- partition@1900000 {
- /* 7MB for User Area */
- reg = <0x01900000 0x00700000>;
- label = "NAND User area";
- };
- };
-
- cpld@3,0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,p1010rdb-cpld";
- reg = <0x3 0x0 0x0000020>;
- bank-width = <1>;
- device-width = <1>;
- };
+ reg = <0x0 0xffe1e000 0 0x2000>;
};
- soc@ffe00000 {
- spi@7000 {
- flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "spansion,s25sl12801";
- reg = <0>;
- spi-max-frequency = <50000000>;
-
- partition@0 {
- /* 1MB for u-boot Bootloader Image */
- /* 1MB for Environment */
- reg = <0x0 0x00100000>;
- label = "SPI Flash U-Boot Image";
- read-only;
- };
-
- partition@100000 {
- /* 512KB for DTB Image */
- reg = <0x00100000 0x00080000>;
- label = "SPI Flash DTB Image";
- };
-
- partition@180000 {
- /* 4MB for Linux Kernel Image */
- reg = <0x00180000 0x00400000>;
- label = "SPI Flash Linux Kernel Image";
- };
-
- partition@580000 {
- /* 4MB for Compressed RFS Image */
- reg = <0x00580000 0x00400000>;
- label = "SPI Flash Compressed RFSImage";
- };
-
- partition@980000 {
- /* 6.5MB for JFFS2 based RFS */
- reg = <0x00980000 0x00680000>;
- label = "SPI Flash JFFS2 RFS";
- };
- };
- };
-
- usb@22000 {
- phy_type = "utmi";
- };
-
- mdio@24000 {
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <3 1>;
- reg = <0x1>;
- };
-
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <2 1>;
- reg = <0x0>;
- };
-
- phy2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- interrupts = <2 1>;
- reg = <0x2>;
- };
- };
-
- enet0: ethernet@b0000 {
- phy-handle = <&phy0>;
- phy-connection-type = "rgmii-id";
- };
-
- enet1: ethernet@b1000 {
- phy-handle = <&phy1>;
- tbi-handle = <&tbi0>;
- phy-connection-type = "sgmii";
- };
-
- enet2: ethernet@b2000 {
- phy-handle = <&phy2>;
- tbi-handle = <&tbi1>;
- phy-connection-type = "sgmii";
- };
+ board_soc: soc: soc@ffe00000 {
+ ranges = <0x0 0x0 0xffe00000 0x100000>;
};
pci0: pcie@ffe09000 {
+ reg = <0 0xffe09000 0 0x1000>;
ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0x0 0x0 0x1 &mpic 0x4 0x1
- 0000 0x0 0x0 0x2 &mpic 0x5 0x1
- 0000 0x0 0x0 0x3 &mpic 0x6 0x1
- 0000 0x0 0x0 0x4 &mpic 0x7 0x1
- >;
-
ranges = <0x2000000 0x0 0xa0000000
0x2000000 0x0 0xa0000000
0x0 0x20000000
@@ -244,24 +47,10 @@
};
pci1: pcie@ffe0a000 {
+ reg = <0 0xffe0a000 0 0x1000>;
ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0x0 0x0 0x1 &mpic 0x4 0x1
- 0000 0x0 0x0 0x2 &mpic 0x5 0x1
- 0000 0x0 0x0 0x3 &mpic 0x6 0x1
- 0000 0x0 0x0 0x4 &mpic 0x7 0x1
- >;
ranges = <0x2000000 0x0 0x80000000
0x2000000 0x0 0x80000000
0x0 0x20000000
@@ -272,3 +61,6 @@
};
};
};
+
+/include/ "p1010rdb.dtsi"
+/include/ "fsl/p1010si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p1010rdb.dtsi b/arch/powerpc/boot/dts/p1010rdb.dtsi
new file mode 100644
index 0000000..149d196
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1010rdb.dtsi
@@ -0,0 +1,222 @@
+/*
+ * P1010 RDB Device Tree Source stub (no addresses or top-level ranges)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&board_ifc {
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x2000000>;
+ bank-width = <2>;
+ device-width = <1>;
+
+ partition@40000 {
+ /* 256KB for DTB Image */
+ reg = <0x00040000 0x00040000>;
+ label = "NOR DTB Image";
+ };
+
+ partition@80000 {
+ /* 7 MB for Linux Kernel Image */
+ reg = <0x00080000 0x00700000>;
+ label = "NOR Linux Kernel Image";
+ };
+
+ partition@800000 {
+ /* 20MB for JFFS2 based Root file System */
+ reg = <0x00800000 0x01400000>;
+ label = "NOR JFFS2 Root File System";
+ };
+
+ partition@1f00000 {
+ /* This location must not be altered */
+ /* 512KB for u-boot Bootloader Image */
+ /* 512KB for u-boot Environment Variables */
+ reg = <0x01f00000 0x00100000>;
+ label = "NOR U-Boot Image";
+ read-only;
+ };
+ };
+
+ nand@1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc-nand";
+ reg = <0x1 0x0 0x10000>;
+
+ partition@0 {
+ /* This location must not be altered */
+ /* 1MB for u-boot Bootloader Image */
+ reg = <0x0 0x00100000>;
+ label = "NAND U-Boot Image";
+ read-only;
+ };
+
+ partition@100000 {
+ /* 1MB for DTB Image */
+ reg = <0x00100000 0x00100000>;
+ label = "NAND DTB Image";
+ };
+
+ partition@200000 {
+ /* 4MB for Linux Kernel Image */
+ reg = <0x00200000 0x00400000>;
+ label = "NAND Linux Kernel Image";
+ };
+
+ partition@600000 {
+ /* 4MB for Compressed Root file System Image */
+ reg = <0x00600000 0x00400000>;
+ label = "NAND Compressed RFS Image";
+ };
+
+ partition@a00000 {
+ /* 15MB for JFFS2 based Root file System */
+ reg = <0x00a00000 0x00f00000>;
+ label = "NAND JFFS2 Root File System";
+ };
+
+ partition@1900000 {
+ /* 7MB for User Area */
+ reg = <0x01900000 0x00700000>;
+ label = "NAND User area";
+ };
+ };
+
+ cpld@3,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,p1010rdb-cpld";
+ reg = <0x3 0x0 0x0000020>;
+ bank-width = <1>;
+ device-width = <1>;
+ };
+};
+
+&board_soc {
+ spi@7000 {
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25sl12801";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+
+ partition@0 {
+ /* 1MB for u-boot Bootloader Image */
+ /* 1MB for Environment */
+ reg = <0x0 0x00100000>;
+ label = "SPI Flash U-Boot Image";
+ read-only;
+ };
+
+ partition@100000 {
+ /* 512KB for DTB Image */
+ reg = <0x00100000 0x00080000>;
+ label = "SPI Flash DTB Image";
+ };
+
+ partition@180000 {
+ /* 4MB for Linux Kernel Image */
+ reg = <0x00180000 0x00400000>;
+ label = "SPI Flash Linux Kernel Image";
+ };
+
+ partition@580000 {
+ /* 4MB for Compressed RFS Image */
+ reg = <0x00580000 0x00400000>;
+ label = "SPI Flash Compressed RFSImage";
+ };
+
+ partition@980000 {
+ /* 6.5MB for JFFS2 based RFS */
+ reg = <0x00980000 0x00680000>;
+ label = "SPI Flash JFFS2 RFS";
+ };
+ };
+ };
+
+ usb@22000 {
+ phy_type = "utmi";
+ dr_mode = "host";
+ };
+
+ mdio@24000 {
+ phy0: ethernet-phy@0 {
+ interrupts = <3 1 0 0>;
+ reg = <0x1>;
+ };
+
+ phy1: ethernet-phy@1 {
+ interrupts = <2 1 0 0>;
+ reg = <0x0>;
+ };
+
+ phy2: ethernet-phy@2 {
+ interrupts = <2 1 0 0>;
+ reg = <0x2>;
+ };
+ };
+
+ mdio@25000 {
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ mdio@26000 {
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet0: ethernet@b0000 {
+ phy-handle = <&phy0>;
+ phy-connection-type = "rgmii-id";
+ };
+
+ enet1: ethernet@b1000 {
+ phy-handle = <&phy1>;
+ tbi-handle = <&tbi0>;
+ phy-connection-type = "sgmii";
+ };
+
+ enet2: ethernet@b2000 {
+ phy-handle = <&phy2>;
+ tbi-handle = <&tbi1>;
+ phy-connection-type = "sgmii";
+ };
+};
diff --git a/arch/powerpc/boot/dts/p1010si.dtsi b/arch/powerpc/boot/dts/p1010si.dtsi
deleted file mode 100644
index cabe0a4..0000000
--- a/arch/powerpc/boot/dts/p1010si.dtsi
+++ /dev/null
@@ -1,374 +0,0 @@
-/*
- * P1010si Device Tree Source
- *
- * Copyright 2011 Freescale Semiconductor Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-/dts-v1/;
-/ {
- compatible = "fsl,P1010";
- #address-cells = <2>;
- #size-cells = <2>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- PowerPC,P1010@0 {
- device_type = "cpu";
- reg = <0x0>;
- next-level-cache = <&L2>;
- };
- };
-
- ifc@ffe1e000 {
- #address-cells = <2>;
- #size-cells = <1>;
- compatible = "fsl,ifc", "simple-bus";
- reg = <0x0 0xffe1e000 0 0x2000>;
- interrupts = <16 2 19 2>;
- interrupt-parent = <&mpic>;
- };
-
- soc@ffe00000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "soc";
- compatible = "fsl,p1010-immr", "simple-bus";
- ranges = <0x0 0x0 0xffe00000 0x100000>;
- bus-frequency = <0>; // Filled out by uboot.
-
- ecm-law@0 {
- compatible = "fsl,ecm-law";
- reg = <0x0 0x1000>;
- fsl,num-laws = <12>;
- };
-
- ecm@1000 {
- compatible = "fsl,p1010-ecm", "fsl,ecm";
- reg = <0x1000 0x1000>;
- interrupts = <16 2>;
- interrupt-parent = <&mpic>;
- };
-
- memory-controller@2000 {
- compatible = "fsl,p1010-memory-controller";
- reg = <0x2000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- };
-
- i2c@3000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x3000 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
- dfsrr;
- };
-
- i2c@3100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- compatible = "fsl-i2c";
- reg = <0x3100 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
- dfsrr;
- };
-
- serial0: serial@4500 {
- cell-index = <0>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4500 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2>;
- interrupt-parent = <&mpic>;
- };
-
- serial1: serial@4600 {
- cell-index = <1>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4600 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2>;
- interrupt-parent = <&mpic>;
- };
-
- spi@7000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,mpc8536-espi";
- reg = <0x7000 0x1000>;
- interrupts = <59 0x2>;
- interrupt-parent = <&mpic>;
- fsl,espi-num-chipselects = <1>;
- };
-
- gpio: gpio-controller@f000 {
- #gpio-cells = <2>;
- compatible = "fsl,mpc8572-gpio";
- reg = <0xf000 0x100>;
- interrupts = <47 0x2>;
- interrupt-parent = <&mpic>;
- gpio-controller;
- };
-
- sata@18000 {
- compatible = "fsl,pq-sata-v2";
- reg = <0x18000 0x1000>;
- cell-index = <1>;
- interrupts = <74 0x2>;
- interrupt-parent = <&mpic>;
- };
-
- sata@19000 {
- compatible = "fsl,pq-sata-v2";
- reg = <0x19000 0x1000>;
- cell-index = <2>;
- interrupts = <41 0x2>;
- interrupt-parent = <&mpic>;
- };
-
- can0: can@1c000 {
- compatible = "fsl,p1010-flexcan";
- reg = <0x1c000 0x1000>;
- interrupts = <48 0x2>;
- interrupt-parent = <&mpic>;
- };
-
- can1: can@1d000 {
- compatible = "fsl,p1010-flexcan";
- reg = <0x1d000 0x1000>;
- interrupts = <61 0x2>;
- interrupt-parent = <&mpic>;
- };
-
- L2: l2-cache-controller@20000 {
- compatible = "fsl,p1010-l2-cache-controller",
- "fsl,p1014-l2-cache-controller";
- reg = <0x20000 0x1000>;
- cache-line-size = <32>; // 32 bytes
- cache-size = <0x40000>; // L2,256K
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- };
-
- dma@21300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,p1010-dma", "fsl,eloplus-dma";
- reg = <0x21300 0x4>;
- ranges = <0x0 0x21100 0x200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,p1010-dma-channel", "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <20 2>;
- };
- dma-channel@80 {
- compatible = "fsl,p1010-dma-channel", "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupt-parent = <&mpic>;
- interrupts = <21 2>;
- };
- dma-channel@100 {
- compatible = "fsl,p1010-dma-channel", "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupt-parent = <&mpic>;
- interrupts = <22 2>;
- };
- dma-channel@180 {
- compatible = "fsl,p1010-dma-channel", "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupt-parent = <&mpic>;
- interrupts = <23 2>;
- };
- };
-
- usb@22000 {
- compatible = "fsl-usb2-dr";
- reg = <0x22000 0x1000>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <28 0x2>;
- dr_mode = "host";
- };
-
- mdio@24000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,etsec2-mdio";
- reg = <0x24000 0x1000 0xb0030 0x4>;
- };
-
- mdio@25000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,etsec2-tbi";
- reg = <0x25000 0x1000 0xb1030 0x4>;
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@26000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,etsec2-tbi";
- reg = <0x26000 0x1000 0xb1030 0x4>;
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- sdhci@2e000 {
- compatible = "fsl,esdhc";
- reg = <0x2e000 0x1000>;
- interrupts = <72 0x8>;
- interrupt-parent = <&mpic>;
- /* Filled in by U-Boot */
- clock-frequency = <0>;
- fsl,sdhci-auto-cmd12;
- };
-
- enet0: ethernet@b0000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "network";
- model = "eTSEC";
- compatible = "fsl,etsec2";
- fsl,num_rx_queues = <0x8>;
- fsl,num_tx_queues = <0x8>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupt-parent = <&mpic>;
-
- queue-group@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xb0000 0x1000>;
- fsl,rx-bit-map = <0xff>;
- fsl,tx-bit-map = <0xff>;
- interrupts = <29 2 30 2 34 2>;
- };
-
- };
-
- enet1: ethernet@b1000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "network";
- model = "eTSEC";
- compatible = "fsl,etsec2";
- fsl,num_rx_queues = <0x8>;
- fsl,num_tx_queues = <0x8>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupt-parent = <&mpic>;
-
- queue-group@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xb1000 0x1000>;
- fsl,rx-bit-map = <0xff>;
- fsl,tx-bit-map = <0xff>;
- interrupts = <35 2 36 2 40 2>;
- };
-
- };
-
- enet2: ethernet@b2000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "network";
- model = "eTSEC";
- compatible = "fsl,etsec2";
- fsl,num_rx_queues = <0x8>;
- fsl,num_tx_queues = <0x8>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupt-parent = <&mpic>;
-
- queue-group@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xb2000 0x1000>;
- fsl,rx-bit-map = <0xff>;
- fsl,tx-bit-map = <0xff>;
- interrupts = <31 2 32 2 33 2>;
- };
-
- };
-
- mpic: pic@40000 {
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <2>;
- reg = <0x40000 0x40000>;
- compatible = "chrp,open-pic";
- device_type = "open-pic";
- };
-
- msi@41600 {
- compatible = "fsl,p1010-msi", "fsl,mpic-msi";
- reg = <0x41600 0x80>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe0 0
- 0xe1 0
- 0xe2 0
- 0xe3 0
- 0xe4 0
- 0xe5 0
- 0xe6 0
- 0xe7 0>;
- interrupt-parent = <&mpic>;
- };
-
- global-utilities@e0000 { //global utilities block
- compatible = "fsl,p1010-guts";
- reg = <0xe0000 0x1000>;
- fsl,has-rstcr;
- };
- };
-
- pci0: pcie@ffe09000 {
- compatible = "fsl,p1010-pcie", "fsl,qoriq-pcie-v2.3", "fsl,qoriq-pcie-v2.2";
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
- reg = <0 0xffe09000 0 0x1000>;
- bus-range = <0 255>;
- clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- };
-
- pci1: pcie@ffe0a000 {
- compatible = "fsl,p1010-pcie", "fsl,qoriq-pcie-v2.3", "fsl,qoriq-pcie-v2.2";
- device_type = "pci";
- #size-cells = <2>;
- #address-cells = <3>;
- reg = <0 0xffe0a000 0 0x1000>;
- bus-range = <0 255>;
- clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- };
-};
--
1.7.3.4
^ permalink raw reply related
* [PATCH 15/29] powerpc/85xx: Add RTC to P1010RDB device tree
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-14-git-send-email-galak@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/p1010rdb.dtsi | 7 +++++++
1 files changed, 7 insertions(+), 0 deletions(-)
diff --git a/arch/powerpc/boot/dts/p1010rdb.dtsi b/arch/powerpc/boot/dts/p1010rdb.dtsi
index 149d196..3aa2b82 100644
--- a/arch/powerpc/boot/dts/p1010rdb.dtsi
+++ b/arch/powerpc/boot/dts/p1010rdb.dtsi
@@ -125,6 +125,13 @@
};
&board_soc {
+ i2c@3000 {
+ rtc@68 {
+ compatible = "pericom,pt7c4338";
+ reg = <0x68>;
+ };
+ };
+
spi@7000 {
flash@0 {
#address-cells = <1>;
--
1.7.3.4
^ permalink raw reply related
* [PATCH 13/29] powerpc/85xx: Rework MPC8572DS device tree
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-12-git-send-email-galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
moved PCI device IRQs down to virtual bridge level
* Moved mdio nodes up one level instead of under tsec nodes
* Added GPIO controller node to MPC8572 SoC template
* Dropping "fsl,mpc8572-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/fsl/mpc8572si-post.dtsi | 196 ++++++
arch/powerpc/boot/dts/fsl/mpc8572si-pre.dtsi | 70 +++
arch/powerpc/boot/dts/mpc8572ds.dts | 757 +-----------------------
arch/powerpc/boot/dts/mpc8572ds.dtsi | 397 +++++++++++++
arch/powerpc/boot/dts/mpc8572ds_36b.dts | 746 +-----------------------
arch/powerpc/boot/dts/mpc8572ds_camp_core0.dts | 487 +--------------
arch/powerpc/boot/dts/mpc8572ds_camp_core1.dts | 245 +++------
7 files changed, 788 insertions(+), 2110 deletions(-)
create mode 100644 arch/powerpc/boot/dts/fsl/mpc8572si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/mpc8572si-pre.dtsi
create mode 100644 arch/powerpc/boot/dts/mpc8572ds.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/mpc8572si-post.dtsi b/arch/powerpc/boot/dts/fsl/mpc8572si-post.dtsi
new file mode 100644
index 0000000..d44e25a
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/mpc8572si-post.dtsi
@@ -0,0 +1,196 @@
+/*
+ * MPC8572 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8572-elbc", "fsl,elbc", "simple-bus";
+ interrupts = <19 2 0 0>;
+};
+
+/* controller at 0x8000 */
+&pci0 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <24 2 0 0>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <24 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x8 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x9 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0xa 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0xb 0x1 0x0 0x0
+ >;
+ };
+};
+
+/* controller at 0x9000 */
+&pci1 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <25 2 0 0>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <25 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x4 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x5 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0x6 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0x7 0x1 0x0 0x0
+ >;
+ };
+};
+
+/* controller at 0xa000 */
+&pci2 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <26 2 0 0>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <26 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+ >;
+ };
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "fsl,mpc8572-immr", "simple-bus";
+ bus-frequency = <0>; // Filled out by uboot.
+
+ ecm-law@0 {
+ compatible = "fsl,ecm-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <12>;
+ };
+
+ ecm@1000 {
+ compatible = "fsl,mpc8572-ecm", "fsl,ecm";
+ reg = <0x1000 0x1000>;
+ interrupts = <17 2 0 0>;
+ };
+
+ memory-controller@2000 {
+ compatible = "fsl,mpc8572-memory-controller";
+ reg = <0x2000 0x1000>;
+ interrupts = <18 2 0 0>;
+ };
+
+ memory-controller@6000 {
+ compatible = "fsl,mpc8572-memory-controller";
+ reg = <0x6000 0x1000>;
+ interrupts = <18 2 0 0>;
+ };
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-duart-0.dtsi"
+/include/ "pq3-dma-1.dtsi"
+/include/ "pq3-gpio-0.dtsi"
+ gpio-controller@f000 {
+ compatible = "fsl,mpc8572-gpio", "fsl,pq3-gpio";
+ };
+
+ L2: l2-cache-controller@20000 {
+ compatible = "fsl,mpc8572-l2-cache-controller";
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x100000>; // L2,1M
+ interrupts = <16 2 0 0>;
+ };
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-etsec1-0.dtsi"
+/include/ "pq3-etsec1-timer-0.dtsi"
+
+ ptp_clock@24e00 {
+ interrupts = <68 2 0 0 69 2 0 0 70 2 0 0 71 2 0 0>;
+ };
+
+/include/ "pq3-etsec1-1.dtsi"
+/include/ "pq3-etsec1-2.dtsi"
+/include/ "pq3-etsec1-3.dtsi"
+/include/ "pq3-sec3.0-0.dtsi"
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-mpic-timer-B.dtsi"
+
+ global-utilities@e0000 {
+ compatible = "fsl,mpc8572-guts";
+ reg = <0xe0000 0x1000>;
+ fsl,has-rstcr;
+ };
+};
diff --git a/arch/powerpc/boot/dts/fsl/mpc8572si-pre.dtsi b/arch/powerpc/boot/dts/fsl/mpc8572si-pre.dtsi
new file mode 100644
index 0000000..ca18832
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/mpc8572si-pre.dtsi
@@ -0,0 +1,70 @@
+/*
+ * MPC8572 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+ compatible = "fsl,MPC8572";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ ethernet3 = &enet3;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,8572@0 {
+ device_type = "cpu";
+ reg = <0x0>;
+ next-level-cache = <&L2>;
+ };
+
+ PowerPC,8572@1 {
+ device_type = "cpu";
+ reg = <0x1>;
+ next-level-cache = <&L2>;
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/mpc8572ds.dts b/arch/powerpc/boot/dts/mpc8572ds.dts
index f6c04d2..0c9f295 100644
--- a/arch/powerpc/boot/dts/mpc8572ds.dts
+++ b/arch/powerpc/boot/dts/mpc8572ds.dts
@@ -9,67 +9,18 @@
* option) any later version.
*/
-/dts-v1/;
+/include/ "fsl/mpc8572si-pre.dtsi"
+
/ {
model = "fsl,MPC8572DS";
compatible = "fsl,MPC8572DS";
- #address-cells = <2>;
- #size-cells = <2>;
-
- aliases {
- ethernet0 = &enet0;
- ethernet1 = &enet1;
- ethernet2 = &enet2;
- ethernet3 = &enet3;
- serial0 = &serial0;
- serial1 = &serial1;
- pci0 = &pci0;
- pci1 = &pci1;
- pci2 = &pci2;
- };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- PowerPC,8572@0 {
- device_type = "cpu";
- reg = <0x0>;
- d-cache-line-size = <32>; // 32 bytes
- i-cache-line-size = <32>; // 32 bytes
- d-cache-size = <0x8000>; // L1, 32K
- i-cache-size = <0x8000>; // L1, 32K
- timebase-frequency = <0>;
- bus-frequency = <0>;
- clock-frequency = <0>;
- next-level-cache = <&L2>;
- };
-
- PowerPC,8572@1 {
- device_type = "cpu";
- reg = <0x1>;
- d-cache-line-size = <32>; // 32 bytes
- i-cache-line-size = <32>; // 32 bytes
- d-cache-size = <0x8000>; // L1, 32K
- i-cache-size = <0x8000>; // L1, 32K
- timebase-frequency = <0>;
- bus-frequency = <0>;
- clock-frequency = <0>;
- next-level-cache = <&L2>;
- };
- };
memory {
device_type = "memory";
};
- localbus@ffe05000 {
- #address-cells = <2>;
- #size-cells = <1>;
- compatible = "fsl,mpc8572-elbc", "fsl,elbc", "simple-bus";
+ board_lbc: lbc: localbus@ffe05000 {
reg = <0 0xffe05000 0 0x1000>;
- interrupts = <19 2>;
- interrupt-parent = <&mpic>;
ranges = <0x0 0x0 0x0 0xe8000000 0x08000000
0x1 0x0 0x0 0xe0000000 0x08000000
@@ -78,601 +29,17 @@
0x4 0x0 0x0 0xffa40000 0x00040000
0x5 0x0 0x0 0xffa80000 0x00040000
0x6 0x0 0x0 0xffac0000 0x00040000>;
-
- nor@0,0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "cfi-flash";
- reg = <0x0 0x0 0x8000000>;
- bank-width = <2>;
- device-width = <1>;
-
- ramdisk@0 {
- reg = <0x0 0x03000000>;
- read-only;
- };
-
- diagnostic@3000000 {
- reg = <0x03000000 0x00e00000>;
- read-only;
- };
-
- dink@3e00000 {
- reg = <0x03e00000 0x00200000>;
- read-only;
- };
-
- kernel@4000000 {
- reg = <0x04000000 0x00400000>;
- read-only;
- };
-
- jffs2@4400000 {
- reg = <0x04400000 0x03b00000>;
- };
-
- dtb@7f00000 {
- reg = <0x07f00000 0x00080000>;
- read-only;
- };
-
- u-boot@7f80000 {
- reg = <0x07f80000 0x00080000>;
- read-only;
- };
- };
-
- nand@2,0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8572-fcm-nand",
- "fsl,elbc-fcm-nand";
- reg = <0x2 0x0 0x40000>;
-
- u-boot@0 {
- reg = <0x0 0x02000000>;
- read-only;
- };
-
- jffs2@2000000 {
- reg = <0x02000000 0x10000000>;
- };
-
- ramdisk@12000000 {
- reg = <0x12000000 0x08000000>;
- read-only;
- };
-
- kernel@1a000000 {
- reg = <0x1a000000 0x04000000>;
- };
-
- dtb@1e000000 {
- reg = <0x1e000000 0x01000000>;
- read-only;
- };
-
- empty@1f000000 {
- reg = <0x1f000000 0x21000000>;
- };
- };
-
- nand@4,0 {
- compatible = "fsl,mpc8572-fcm-nand",
- "fsl,elbc-fcm-nand";
- reg = <0x4 0x0 0x40000>;
- };
-
- nand@5,0 {
- compatible = "fsl,mpc8572-fcm-nand",
- "fsl,elbc-fcm-nand";
- reg = <0x5 0x0 0x40000>;
- };
-
- nand@6,0 {
- compatible = "fsl,mpc8572-fcm-nand",
- "fsl,elbc-fcm-nand";
- reg = <0x6 0x0 0x40000>;
- };
};
- soc8572@ffe00000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "soc";
- compatible = "simple-bus";
+ board_soc: soc: soc8572@ffe00000 {
ranges = <0x0 0 0xffe00000 0x100000>;
- bus-frequency = <0>; // Filled out by uboot.
-
- ecm-law@0 {
- compatible = "fsl,ecm-law";
- reg = <0x0 0x1000>;
- fsl,num-laws = <12>;
- };
-
- ecm@1000 {
- compatible = "fsl,mpc8572-ecm", "fsl,ecm";
- reg = <0x1000 0x1000>;
- interrupts = <17 2>;
- interrupt-parent = <&mpic>;
- };
-
- memory-controller@2000 {
- compatible = "fsl,mpc8572-memory-controller";
- reg = <0x2000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <18 2>;
- };
-
- memory-controller@6000 {
- compatible = "fsl,mpc8572-memory-controller";
- reg = <0x6000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <18 2>;
- };
-
- L2: l2-cache-controller@20000 {
- compatible = "fsl,mpc8572-l2-cache-controller";
- reg = <0x20000 0x1000>;
- cache-line-size = <32>; // 32 bytes
- cache-size = <0x100000>; // L2, 1M
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- };
-
- i2c@3000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x3000 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
- dfsrr;
- };
-
- i2c@3100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- compatible = "fsl-i2c";
- reg = <0x3100 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
- dfsrr;
- };
-
- dma@c300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8572-dma", "fsl,eloplus-dma";
- reg = <0xc300 0x4>;
- ranges = <0x0 0xc100 0x200>;
- cell-index = <1>;
- dma-channel@0 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <76 2>;
- };
- dma-channel@80 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupt-parent = <&mpic>;
- interrupts = <77 2>;
- };
- dma-channel@100 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupt-parent = <&mpic>;
- interrupts = <78 2>;
- };
- dma-channel@180 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupt-parent = <&mpic>;
- interrupts = <79 2>;
- };
- };
-
- dma@21300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8572-dma", "fsl,eloplus-dma";
- reg = <0x21300 0x4>;
- ranges = <0x0 0x21100 0x200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <20 2>;
- };
- dma-channel@80 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupt-parent = <&mpic>;
- interrupts = <21 2>;
- };
- dma-channel@100 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupt-parent = <&mpic>;
- interrupts = <22 2>;
- };
- dma-channel@180 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupt-parent = <&mpic>;
- interrupts = <23 2>;
- };
- };
-
- ptp_clock@24E00 {
- compatible = "fsl,etsec-ptp";
- reg = <0x24E00 0xB0>;
- interrupts = <68 2 69 2 70 2 71 2>;
- interrupt-parent = < &mpic >;
- fsl,tclk-period = <5>;
- fsl,tmr-prsc = <200>;
- fsl,tmr-add = <0xAAAAAAAB>;
- fsl,tmr-fiper1 = <0x3B9AC9FB>;
- fsl,tmr-fiper2 = <0x3B9AC9FB>;
- fsl,max-adj = <499999999>;
- };
-
- enet0: ethernet@24000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <0>;
- device_type = "network";
- model = "eTSEC";
- compatible = "gianfar";
- reg = <0x24000 0x1000>;
- ranges = <0x0 0x24000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <29 2 30 2 34 2>;
- interrupt-parent = <&mpic>;
- tbi-handle = <&tbi0>;
- phy-handle = <&phy0>;
- phy-connection-type = "rgmii-id";
-
- mdio@520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x0>;
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x1>;
- };
- phy2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x2>;
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x3>;
- };
-
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
- };
-
- enet1: ethernet@25000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <1>;
- device_type = "network";
- model = "eTSEC";
- compatible = "gianfar";
- reg = <0x25000 0x1000>;
- ranges = <0x0 0x25000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <35 2 36 2 40 2>;
- interrupt-parent = <&mpic>;
- tbi-handle = <&tbi1>;
- phy-handle = <&phy1>;
- phy-connection-type = "rgmii-id";
-
- mdio@520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
- };
-
- enet2: ethernet@26000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <2>;
- device_type = "network";
- model = "eTSEC";
- compatible = "gianfar";
- reg = <0x26000 0x1000>;
- ranges = <0x0 0x26000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <31 2 32 2 33 2>;
- interrupt-parent = <&mpic>;
- tbi-handle = <&tbi2>;
- phy-handle = <&phy2>;
- phy-connection-type = "rgmii-id";
-
- mdio@520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x520 0x20>;
-
- tbi2: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
- };
-
- enet3: ethernet@27000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <3>;
- device_type = "network";
- model = "eTSEC";
- compatible = "gianfar";
- reg = <0x27000 0x1000>;
- ranges = <0x0 0x27000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <37 2 38 2 39 2>;
- interrupt-parent = <&mpic>;
- tbi-handle = <&tbi3>;
- phy-handle = <&phy3>;
- phy-connection-type = "rgmii-id";
-
- mdio@520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x520 0x20>;
-
- tbi3: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
- };
-
- serial0: serial@4500 {
- cell-index = <0>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4500 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2>;
- interrupt-parent = <&mpic>;
- };
-
- serial1: serial@4600 {
- cell-index = <1>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4600 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2>;
- interrupt-parent = <&mpic>;
- };
-
- global-utilities@e0000 { //global utilities block
- compatible = "fsl,mpc8572-guts";
- reg = <0xe0000 0x1000>;
- fsl,has-rstcr;
- };
-
- msi@41600 {
- compatible = "fsl,mpc8572-msi", "fsl,mpic-msi";
- reg = <0x41600 0x80>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe0 0
- 0xe1 0
- 0xe2 0
- 0xe3 0
- 0xe4 0
- 0xe5 0
- 0xe6 0
- 0xe7 0>;
- interrupt-parent = <&mpic>;
- };
-
- crypto@30000 {
- compatible = "fsl,sec3.0", "fsl,sec2.4", "fsl,sec2.2",
- "fsl,sec2.1", "fsl,sec2.0";
- reg = <0x30000 0x10000>;
- interrupts = <45 2 58 2>;
- interrupt-parent = <&mpic>;
- fsl,num-channels = <4>;
- fsl,channel-fifo-len = <24>;
- fsl,exec-units-mask = <0x9fe>;
- fsl,descriptor-types-mask = <0x3ab0ebf>;
- };
-
- mpic: pic@40000 {
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <2>;
- reg = <0x40000 0x40000>;
- compatible = "chrp,open-pic";
- device_type = "open-pic";
- };
};
- pci0: pcie@ffe08000 {
- compatible = "fsl,mpc8548-pcie";
- device_type = "pci";
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
+ board_pci0: pci0: pcie@ffe08000 {
reg = <0 0xffe08000 0 0x1000>;
- bus-range = <0 255>;
ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x00010000>;
- clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <24 2>;
- interrupt-map-mask = <0xff00 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x11 func 0 - PCI slot 1 */
- 0x8800 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8800 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8800 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8800 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 1 - PCI slot 1 */
- 0x8900 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8900 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8900 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8900 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 2 - PCI slot 1 */
- 0x8a00 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8a00 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8a00 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8a00 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 3 - PCI slot 1 */
- 0x8b00 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8b00 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8b00 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8b00 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 4 - PCI slot 1 */
- 0x8c00 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8c00 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8c00 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8c00 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 5 - PCI slot 1 */
- 0x8d00 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8d00 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8d00 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8d00 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 6 - PCI slot 1 */
- 0x8e00 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8e00 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8e00 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8e00 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 7 - PCI slot 1 */
- 0x8f00 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8f00 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8f00 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8f00 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x12 func 0 - PCI slot 2 */
- 0x9000 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9000 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9000 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9000 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 1 - PCI slot 2 */
- 0x9100 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9100 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9100 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9100 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 2 - PCI slot 2 */
- 0x9200 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9200 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9200 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9200 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 3 - PCI slot 2 */
- 0x9300 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9300 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9300 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9300 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 4 - PCI slot 2 */
- 0x9400 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9400 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9400 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9400 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 5 - PCI slot 2 */
- 0x9500 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9500 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9500 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9500 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 6 - PCI slot 2 */
- 0x9600 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9600 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9600 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9600 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 7 - PCI slot 2 */
- 0x9700 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9700 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9700 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9700 0x0 0x0 0x4 &mpic 0x2 0x1
-
- // IDSEL 0x1c USB
- 0xe000 0x0 0x0 0x1 &i8259 0xc 0x2
- 0xe100 0x0 0x0 0x2 &i8259 0x9 0x2
- 0xe200 0x0 0x0 0x3 &i8259 0xa 0x2
- 0xe300 0x0 0x0 0x4 &i8259 0xb 0x2
-
- // IDSEL 0x1d Audio
- 0xe800 0x0 0x0 0x1 &i8259 0x6 0x2
-
- // IDSEL 0x1e Legacy
- 0xf000 0x0 0x0 0x1 &i8259 0x7 0x2
- 0xf100 0x0 0x0 0x1 &i8259 0x7 0x2
-
- // IDSEL 0x1f IDE/SATA
- 0xf800 0x0 0x0 0x1 &i8259 0xe 0x2
- 0xf900 0x0 0x0 0x1 &i8259 0x5 0x2
-
- >;
-
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
ranges = <0x2000000 0x0 0x80000000
0x2000000 0x0 0x80000000
0x0 0x20000000
@@ -680,99 +47,14 @@
0x1000000 0x0 0x0
0x1000000 0x0 0x0
0x0 0x10000>;
- uli1575@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- ranges = <0x2000000 0x0 0x80000000
- 0x2000000 0x0 0x80000000
- 0x0 0x20000000
-
- 0x1000000 0x0 0x0
- 0x1000000 0x0 0x0
- 0x0 0x10000>;
- isa@1e {
- device_type = "isa";
- #interrupt-cells = <2>;
- #size-cells = <1>;
- #address-cells = <2>;
- reg = <0xf000 0x0 0x0 0x0 0x0>;
- ranges = <0x1 0x0 0x1000000 0x0 0x0
- 0x1000>;
- interrupt-parent = <&i8259>;
-
- i8259: interrupt-controller@20 {
- reg = <0x1 0x20 0x2
- 0x1 0xa0 0x2
- 0x1 0x4d0 0x2>;
- interrupt-controller;
- device_type = "interrupt-controller";
- #address-cells = <0>;
- #interrupt-cells = <2>;
- compatible = "chrp,iic";
- interrupts = <9 2>;
- interrupt-parent = <&mpic>;
- };
-
- i8042@60 {
- #size-cells = <0>;
- #address-cells = <1>;
- reg = <0x1 0x60 0x1 0x1 0x64 0x1>;
- interrupts = <1 3 12 3>;
- interrupt-parent =
- <&i8259>;
-
- keyboard@0 {
- reg = <0x0>;
- compatible = "pnpPNP,303";
- };
-
- mouse@1 {
- reg = <0x1>;
- compatible = "pnpPNP,f03";
- };
- };
-
- rtc@70 {
- compatible = "pnpPNP,b00";
- reg = <0x1 0x70 0x2>;
- };
-
- gpio@400 {
- reg = <0x1 0x400 0x80>;
- };
- };
- };
};
-
};
pci1: pcie@ffe09000 {
- compatible = "fsl,mpc8548-pcie";
- device_type = "pci";
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
reg = <0 0xffe09000 0 0x1000>;
- bus-range = <0 255>;
ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x00010000>;
- clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <25 2>;
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0x0 0x0 0x1 &mpic 0x4 0x1
- 0000 0x0 0x0 0x2 &mpic 0x5 0x1
- 0000 0x0 0x0 0x3 &mpic 0x6 0x1
- 0000 0x0 0x0 0x4 &mpic 0x7 0x1
- >;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
ranges = <0x2000000 0x0 0xa0000000
0x2000000 0x0 0xa0000000
0x0 0x20000000
@@ -784,31 +66,10 @@
};
pci2: pcie@ffe0a000 {
- compatible = "fsl,mpc8548-pcie";
- device_type = "pci";
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
reg = <0 0xffe0a000 0 0x1000>;
- bus-range = <0 255>;
ranges = <0x2000000 0x0 0xc0000000 0 0xc0000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc20000 0x0 0x00010000>;
- clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <26 2>;
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0x0 0x0 0x1 &mpic 0x0 0x1
- 0000 0x0 0x0 0x2 &mpic 0x1 0x1
- 0000 0x0 0x0 0x3 &mpic 0x2 0x1
- 0000 0x0 0x0 0x4 &mpic 0x3 0x1
- >;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
ranges = <0x2000000 0x0 0xc0000000
0x2000000 0x0 0xc0000000
0x0 0x20000000
@@ -819,3 +80,11 @@
};
};
};
+
+/*
+ * mpc8572ds.dtsi must be last to ensure board_pci0 overrides pci0 settings
+ * for interrupt-map & interrupt-map-mask
+ */
+
+/include/ "fsl/mpc8572si-post.dtsi"
+/include/ "mpc8572ds.dtsi"
diff --git a/arch/powerpc/boot/dts/mpc8572ds.dtsi b/arch/powerpc/boot/dts/mpc8572ds.dtsi
new file mode 100644
index 0000000..c3d4fac
--- /dev/null
+++ b/arch/powerpc/boot/dts/mpc8572ds.dtsi
@@ -0,0 +1,397 @@
+/*
+ * MPC8572DS Device Tree Source stub (no addresses or top-level ranges)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&board_lbc {
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x8000000>;
+ bank-width = <2>;
+ device-width = <1>;
+
+ ramdisk@0 {
+ reg = <0x0 0x03000000>;
+ read-only;
+ };
+
+ diagnostic@3000000 {
+ reg = <0x03000000 0x00e00000>;
+ read-only;
+ };
+
+ dink@3e00000 {
+ reg = <0x03e00000 0x00200000>;
+ read-only;
+ };
+
+ kernel@4000000 {
+ reg = <0x04000000 0x00400000>;
+ read-only;
+ };
+
+ jffs2@4400000 {
+ reg = <0x04400000 0x03b00000>;
+ };
+
+ dtb@7f00000 {
+ reg = <0x07f00000 0x00080000>;
+ read-only;
+ };
+
+ u-boot@7f80000 {
+ reg = <0x07f80000 0x00080000>;
+ read-only;
+ };
+ };
+
+ nand@2,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8572-fcm-nand",
+ "fsl,elbc-fcm-nand";
+ reg = <0x2 0x0 0x40000>;
+
+ u-boot@0 {
+ reg = <0x0 0x02000000>;
+ read-only;
+ };
+
+ jffs2@2000000 {
+ reg = <0x02000000 0x10000000>;
+ };
+
+ ramdisk@12000000 {
+ reg = <0x12000000 0x08000000>;
+ read-only;
+ };
+
+ kernel@1a000000 {
+ reg = <0x1a000000 0x04000000>;
+ };
+
+ dtb@1e000000 {
+ reg = <0x1e000000 0x01000000>;
+ read-only;
+ };
+
+ empty@1f000000 {
+ reg = <0x1f000000 0x21000000>;
+ };
+ };
+
+ nand@4,0 {
+ compatible = "fsl,mpc8572-fcm-nand",
+ "fsl,elbc-fcm-nand";
+ reg = <0x4 0x0 0x40000>;
+ };
+
+ nand@5,0 {
+ compatible = "fsl,mpc8572-fcm-nand",
+ "fsl,elbc-fcm-nand";
+ reg = <0x5 0x0 0x40000>;
+ };
+
+ nand@6,0 {
+ compatible = "fsl,mpc8572-fcm-nand",
+ "fsl,elbc-fcm-nand";
+ reg = <0x6 0x0 0x40000>;
+ };
+};
+
+&board_soc {
+ enet0: ethernet@24000 {
+ tbi-handle = <&tbi0>;
+ phy-handle = <&phy0>;
+ phy-connection-type = "rgmii-id";
+ };
+
+ mdio@24520 {
+ phy0: ethernet-phy@0 {
+ interrupts = <10 1 0 0>;
+ reg = <0x0>;
+ };
+ phy1: ethernet-phy@1 {
+ interrupts = <10 1 0 0>;
+ reg = <0x1>;
+ };
+ phy2: ethernet-phy@2 {
+ interrupts = <10 1 0 0>;
+ reg = <0x2>;
+ };
+ phy3: ethernet-phy@3 {
+ interrupts = <10 1 0 0>;
+ reg = <0x3>;
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ ptp_clock@24e00 {
+ fsl,tclk-period = <5>;
+ fsl,tmr-prsc = <200>;
+ fsl,tmr-add = <0xAAAAAAAB>;
+ fsl,tmr-fiper1 = <0x3B9AC9FB>;
+ fsl,tmr-fiper2 = <0x3B9AC9FB>;
+ fsl,max-adj = <499999999>;
+ };
+
+ enet1: ethernet@25000 {
+ tbi-handle = <&tbi1>;
+ phy-handle = <&phy1>;
+ phy-connection-type = "rgmii-id";
+
+ };
+
+ mdio@25520 {
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet2: ethernet@26000 {
+ tbi-handle = <&tbi2>;
+ phy-handle = <&phy2>;
+ phy-connection-type = "rgmii-id";
+
+ };
+ mdio@26520 {
+ tbi2: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet3: ethernet@27000 {
+ tbi-handle = <&tbi3>;
+ phy-handle = <&phy3>;
+ phy-connection-type = "rgmii-id";
+ };
+
+ mdio@27520 {
+ tbi3: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+};
+
+&board_pci0 {
+ pcie@0 {
+ interrupt-map-mask = <0xff00 0x0 0x0 0x7>;
+ interrupt-map = <
+ /* IDSEL 0x11 func 0 - PCI slot 1 */
+ 0x8800 0x0 0x0 0x1 &mpic 0x2 0x1 0 0
+ 0x8800 0x0 0x0 0x2 &mpic 0x3 0x1 0 0
+ 0x8800 0x0 0x0 0x3 &mpic 0x4 0x1 0 0
+ 0x8800 0x0 0x0 0x4 &mpic 0x1 0x1 0 0
+
+ /* IDSEL 0x11 func 1 - PCI slot 1 */
+ 0x8900 0x0 0x0 0x1 &mpic 0x2 0x1 0 0
+ 0x8900 0x0 0x0 0x2 &mpic 0x3 0x1 0 0
+ 0x8900 0x0 0x0 0x3 &mpic 0x4 0x1 0 0
+ 0x8900 0x0 0x0 0x4 &mpic 0x1 0x1 0 0
+
+ /* IDSEL 0x11 func 2 - PCI slot 1 */
+ 0x8a00 0x0 0x0 0x1 &mpic 0x2 0x1 0 0
+ 0x8a00 0x0 0x0 0x2 &mpic 0x3 0x1 0 0
+ 0x8a00 0x0 0x0 0x3 &mpic 0x4 0x1 0 0
+ 0x8a00 0x0 0x0 0x4 &mpic 0x1 0x1 0 0
+
+ /* IDSEL 0x11 func 3 - PCI slot 1 */
+ 0x8b00 0x0 0x0 0x1 &mpic 0x2 0x1 0 0
+ 0x8b00 0x0 0x0 0x2 &mpic 0x3 0x1 0 0
+ 0x8b00 0x0 0x0 0x3 &mpic 0x4 0x1 0 0
+ 0x8b00 0x0 0x0 0x4 &mpic 0x1 0x1 0 0
+
+ /* IDSEL 0x11 func 4 - PCI slot 1 */
+ 0x8c00 0x0 0x0 0x1 &mpic 0x2 0x1 0 0
+ 0x8c00 0x0 0x0 0x2 &mpic 0x3 0x1 0 0
+ 0x8c00 0x0 0x0 0x3 &mpic 0x4 0x1 0 0
+ 0x8c00 0x0 0x0 0x4 &mpic 0x1 0x1 0 0
+
+ /* IDSEL 0x11 func 5 - PCI slot 1 */
+ 0x8d00 0x0 0x0 0x1 &mpic 0x2 0x1 0 0
+ 0x8d00 0x0 0x0 0x2 &mpic 0x3 0x1 0 0
+ 0x8d00 0x0 0x0 0x3 &mpic 0x4 0x1 0 0
+ 0x8d00 0x0 0x0 0x4 &mpic 0x1 0x1 0 0
+
+ /* IDSEL 0x11 func 6 - PCI slot 1 */
+ 0x8e00 0x0 0x0 0x1 &mpic 0x2 0x1 0 0
+ 0x8e00 0x0 0x0 0x2 &mpic 0x3 0x1 0 0
+ 0x8e00 0x0 0x0 0x3 &mpic 0x4 0x1 0 0
+ 0x8e00 0x0 0x0 0x4 &mpic 0x1 0x1 0 0
+
+ /* IDSEL 0x11 func 7 - PCI slot 1 */
+ 0x8f00 0x0 0x0 0x1 &mpic 0x2 0x1 0 0
+ 0x8f00 0x0 0x0 0x2 &mpic 0x3 0x1 0 0
+ 0x8f00 0x0 0x0 0x3 &mpic 0x4 0x1 0 0
+ 0x8f00 0x0 0x0 0x4 &mpic 0x1 0x1 0 0
+
+ /* IDSEL 0x12 func 0 - PCI slot 2 */
+ 0x9000 0x0 0x0 0x1 &mpic 0x3 0x1 0 0
+ 0x9000 0x0 0x0 0x2 &mpic 0x4 0x1 0 0
+ 0x9000 0x0 0x0 0x3 &mpic 0x1 0x1 0 0
+ 0x9000 0x0 0x0 0x4 &mpic 0x2 0x1 0 0
+
+ /* IDSEL 0x12 func 1 - PCI slot 2 */
+ 0x9100 0x0 0x0 0x1 &mpic 0x3 0x1 0 0
+ 0x9100 0x0 0x0 0x2 &mpic 0x4 0x1 0 0
+ 0x9100 0x0 0x0 0x3 &mpic 0x1 0x1 0 0
+ 0x9100 0x0 0x0 0x4 &mpic 0x2 0x1 0 0
+
+ /* IDSEL 0x12 func 2 - PCI slot 2 */
+ 0x9200 0x0 0x0 0x1 &mpic 0x3 0x1 0 0
+ 0x9200 0x0 0x0 0x2 &mpic 0x4 0x1 0 0
+ 0x9200 0x0 0x0 0x3 &mpic 0x1 0x1 0 0
+ 0x9200 0x0 0x0 0x4 &mpic 0x2 0x1 0 0
+
+ /* IDSEL 0x12 func 3 - PCI slot 2 */
+ 0x9300 0x0 0x0 0x1 &mpic 0x3 0x1 0 0
+ 0x9300 0x0 0x0 0x2 &mpic 0x4 0x1 0 0
+ 0x9300 0x0 0x0 0x3 &mpic 0x1 0x1 0 0
+ 0x9300 0x0 0x0 0x4 &mpic 0x2 0x1 0 0
+
+ /* IDSEL 0x12 func 4 - PCI slot 2 */
+ 0x9400 0x0 0x0 0x1 &mpic 0x3 0x1 0 0
+ 0x9400 0x0 0x0 0x2 &mpic 0x4 0x1 0 0
+ 0x9400 0x0 0x0 0x3 &mpic 0x1 0x1 0 0
+ 0x9400 0x0 0x0 0x4 &mpic 0x2 0x1 0 0
+
+ /* IDSEL 0x12 func 5 - PCI slot 2 */
+ 0x9500 0x0 0x0 0x1 &mpic 0x3 0x1 0 0
+ 0x9500 0x0 0x0 0x2 &mpic 0x4 0x1 0 0
+ 0x9500 0x0 0x0 0x3 &mpic 0x1 0x1 0 0
+ 0x9500 0x0 0x0 0x4 &mpic 0x2 0x1 0 0
+
+ /* IDSEL 0x12 func 6 - PCI slot 2 */
+ 0x9600 0x0 0x0 0x1 &mpic 0x3 0x1 0 0
+ 0x9600 0x0 0x0 0x2 &mpic 0x4 0x1 0 0
+ 0x9600 0x0 0x0 0x3 &mpic 0x1 0x1 0 0
+ 0x9600 0x0 0x0 0x4 &mpic 0x2 0x1 0 0
+
+ /* IDSEL 0x12 func 7 - PCI slot 2 */
+ 0x9700 0x0 0x0 0x1 &mpic 0x3 0x1 0 0
+ 0x9700 0x0 0x0 0x2 &mpic 0x4 0x1 0 0
+ 0x9700 0x0 0x0 0x3 &mpic 0x1 0x1 0 0
+ 0x9700 0x0 0x0 0x4 &mpic 0x2 0x1 0 0
+
+ // IDSEL 0x1c USB
+ 0xe000 0x0 0x0 0x1 &i8259 0xc 0x2
+ 0xe100 0x0 0x0 0x2 &i8259 0x9 0x2
+ 0xe200 0x0 0x0 0x3 &i8259 0xa 0x2
+ 0xe300 0x0 0x0 0x4 &i8259 0xb 0x2
+
+ // IDSEL 0x1d Audio
+ 0xe800 0x0 0x0 0x1 &i8259 0x6 0x2
+
+ // IDSEL 0x1e Legacy
+ 0xf000 0x0 0x0 0x1 &i8259 0x7 0x2
+ 0xf100 0x0 0x0 0x1 &i8259 0x7 0x2
+
+ // IDSEL 0x1f IDE/SATA
+ 0xf800 0x0 0x0 0x1 &i8259 0xe 0x2
+ 0xf900 0x0 0x0 0x1 &i8259 0x5 0x2
+ >;
+
+
+ uli1575@0 {
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ ranges = <0x2000000 0x0 0x80000000
+ 0x2000000 0x0 0x80000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x10000>;
+ isa@1e {
+ device_type = "isa";
+ #interrupt-cells = <2>;
+ #size-cells = <1>;
+ #address-cells = <2>;
+ reg = <0xf000 0x0 0x0 0x0 0x0>;
+ ranges = <0x1 0x0 0x1000000 0x0 0x0
+ 0x1000>;
+ interrupt-parent = <&i8259>;
+
+ i8259: interrupt-controller@20 {
+ reg = <0x1 0x20 0x2
+ 0x1 0xa0 0x2
+ 0x1 0x4d0 0x2>;
+ interrupt-controller;
+ device_type = "interrupt-controller";
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ compatible = "chrp,iic";
+ interrupts = <9 2 0 0>;
+ interrupt-parent = <&mpic>;
+ };
+
+ i8042@60 {
+ #size-cells = <0>;
+ #address-cells = <1>;
+ reg = <0x1 0x60 0x1 0x1 0x64 0x1>;
+ interrupts = <1 3 12 3>;
+ interrupt-parent =
+ <&i8259>;
+
+ keyboard@0 {
+ reg = <0x0>;
+ compatible = "pnpPNP,303";
+ };
+
+ mouse@1 {
+ reg = <0x1>;
+ compatible = "pnpPNP,f03";
+ };
+ };
+
+ rtc@70 {
+ compatible = "pnpPNP,b00";
+ reg = <0x1 0x70 0x2>;
+ };
+
+ gpio@400 {
+ reg = <0x1 0x400 0x80>;
+ };
+ };
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/mpc8572ds_36b.dts b/arch/powerpc/boot/dts/mpc8572ds_36b.dts
index f6365db..6c3d0b3 100644
--- a/arch/powerpc/boot/dts/mpc8572ds_36b.dts
+++ b/arch/powerpc/boot/dts/mpc8572ds_36b.dts
@@ -1,5 +1,5 @@
/*
- * MPC8572 DS Device Tree Source
+ * MPC8572DS Device Tree Source (36-bit address map)
*
* Copyright 2007-2009 Freescale Semiconductor Inc.
*
@@ -9,67 +9,18 @@
* option) any later version.
*/
-/dts-v1/;
+/include/ "fsl/mpc8572si-pre.dtsi"
+
/ {
model = "fsl,MPC8572DS";
compatible = "fsl,MPC8572DS";
- #address-cells = <2>;
- #size-cells = <2>;
-
- aliases {
- ethernet0 = &enet0;
- ethernet1 = &enet1;
- ethernet2 = &enet2;
- ethernet3 = &enet3;
- serial0 = &serial0;
- serial1 = &serial1;
- pci0 = &pci0;
- pci1 = &pci1;
- pci2 = &pci2;
- };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- PowerPC,8572@0 {
- device_type = "cpu";
- reg = <0x0>;
- d-cache-line-size = <32>; // 32 bytes
- i-cache-line-size = <32>; // 32 bytes
- d-cache-size = <0x8000>; // L1, 32K
- i-cache-size = <0x8000>; // L1, 32K
- timebase-frequency = <0>;
- bus-frequency = <0>;
- clock-frequency = <0>;
- next-level-cache = <&L2>;
- };
-
- PowerPC,8572@1 {
- device_type = "cpu";
- reg = <0x1>;
- d-cache-line-size = <32>; // 32 bytes
- i-cache-line-size = <32>; // 32 bytes
- d-cache-size = <0x8000>; // L1, 32K
- i-cache-size = <0x8000>; // L1, 32K
- timebase-frequency = <0>;
- bus-frequency = <0>;
- clock-frequency = <0>;
- next-level-cache = <&L2>;
- };
- };
memory {
device_type = "memory";
};
- localbus@fffe05000 {
- #address-cells = <2>;
- #size-cells = <1>;
- compatible = "fsl,mpc8572-elbc", "fsl,elbc", "simple-bus";
+ board_lbc: lbc: localbus@fffe05000 {
reg = <0xf 0xffe05000 0 0x1000>;
- interrupts = <19 2>;
- interrupt-parent = <&mpic>;
ranges = <0x0 0x0 0xf 0xe8000000 0x08000000
0x1 0x0 0xf 0xe0000000 0x08000000
@@ -78,588 +29,17 @@
0x4 0x0 0xf 0xffa40000 0x00040000
0x5 0x0 0xf 0xffa80000 0x00040000
0x6 0x0 0xf 0xffac0000 0x00040000>;
-
- nor@0,0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "cfi-flash";
- reg = <0x0 0x0 0x8000000>;
- bank-width = <2>;
- device-width = <1>;
-
- ramdisk@0 {
- reg = <0x0 0x03000000>;
- read-only;
- };
-
- diagnostic@3000000 {
- reg = <0x03000000 0x00e00000>;
- read-only;
- };
-
- dink@3e00000 {
- reg = <0x03e00000 0x00200000>;
- read-only;
- };
-
- kernel@4000000 {
- reg = <0x04000000 0x00400000>;
- read-only;
- };
-
- jffs2@4400000 {
- reg = <0x04400000 0x03b00000>;
- };
-
- dtb@7f00000 {
- reg = <0x07f00000 0x00080000>;
- read-only;
- };
-
- u-boot@7f80000 {
- reg = <0x07f80000 0x00080000>;
- read-only;
- };
- };
-
- nand@2,0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8572-fcm-nand",
- "fsl,elbc-fcm-nand";
- reg = <0x2 0x0 0x40000>;
-
- u-boot@0 {
- reg = <0x0 0x02000000>;
- read-only;
- };
-
- jffs2@2000000 {
- reg = <0x02000000 0x10000000>;
- };
-
- ramdisk@12000000 {
- reg = <0x12000000 0x08000000>;
- read-only;
- };
-
- kernel@1a000000 {
- reg = <0x1a000000 0x04000000>;
- };
-
- dtb@1e000000 {
- reg = <0x1e000000 0x01000000>;
- read-only;
- };
-
- empty@1f000000 {
- reg = <0x1f000000 0x21000000>;
- };
- };
-
- nand@4,0 {
- compatible = "fsl,mpc8572-fcm-nand",
- "fsl,elbc-fcm-nand";
- reg = <0x4 0x0 0x40000>;
- };
-
- nand@5,0 {
- compatible = "fsl,mpc8572-fcm-nand",
- "fsl,elbc-fcm-nand";
- reg = <0x5 0x0 0x40000>;
- };
-
- nand@6,0 {
- compatible = "fsl,mpc8572-fcm-nand",
- "fsl,elbc-fcm-nand";
- reg = <0x6 0x0 0x40000>;
- };
};
- soc8572@fffe00000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "soc";
- compatible = "simple-bus";
+ board_soc: soc: soc8572@fffe00000 {
ranges = <0x0 0xf 0xffe00000 0x100000>;
- bus-frequency = <0>; // Filled out by uboot.
-
- ecm-law@0 {
- compatible = "fsl,ecm-law";
- reg = <0x0 0x1000>;
- fsl,num-laws = <12>;
- };
-
- ecm@1000 {
- compatible = "fsl,mpc8572-ecm", "fsl,ecm";
- reg = <0x1000 0x1000>;
- interrupts = <17 2>;
- interrupt-parent = <&mpic>;
- };
-
- memory-controller@2000 {
- compatible = "fsl,mpc8572-memory-controller";
- reg = <0x2000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <18 2>;
- };
-
- memory-controller@6000 {
- compatible = "fsl,mpc8572-memory-controller";
- reg = <0x6000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <18 2>;
- };
-
- L2: l2-cache-controller@20000 {
- compatible = "fsl,mpc8572-l2-cache-controller";
- reg = <0x20000 0x1000>;
- cache-line-size = <32>; // 32 bytes
- cache-size = <0x100000>; // L2, 1M
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- };
-
- i2c@3000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x3000 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
- dfsrr;
- };
-
- i2c@3100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- compatible = "fsl-i2c";
- reg = <0x3100 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
- dfsrr;
- };
-
- dma@c300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8572-dma", "fsl,eloplus-dma";
- reg = <0xc300 0x4>;
- ranges = <0x0 0xc100 0x200>;
- cell-index = <1>;
- dma-channel@0 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <76 2>;
- };
- dma-channel@80 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupt-parent = <&mpic>;
- interrupts = <77 2>;
- };
- dma-channel@100 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupt-parent = <&mpic>;
- interrupts = <78 2>;
- };
- dma-channel@180 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupt-parent = <&mpic>;
- interrupts = <79 2>;
- };
- };
-
- dma@21300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8572-dma", "fsl,eloplus-dma";
- reg = <0x21300 0x4>;
- ranges = <0x0 0x21100 0x200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <20 2>;
- };
- dma-channel@80 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupt-parent = <&mpic>;
- interrupts = <21 2>;
- };
- dma-channel@100 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupt-parent = <&mpic>;
- interrupts = <22 2>;
- };
- dma-channel@180 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupt-parent = <&mpic>;
- interrupts = <23 2>;
- };
- };
-
- enet0: ethernet@24000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <0>;
- device_type = "network";
- model = "eTSEC";
- compatible = "gianfar";
- reg = <0x24000 0x1000>;
- ranges = <0x0 0x24000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <29 2 30 2 34 2>;
- interrupt-parent = <&mpic>;
- tbi-handle = <&tbi0>;
- phy-handle = <&phy0>;
- phy-connection-type = "rgmii-id";
-
- mdio@520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x0>;
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x1>;
- };
- phy2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x2>;
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x3>;
- };
-
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
- };
-
- enet1: ethernet@25000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <1>;
- device_type = "network";
- model = "eTSEC";
- compatible = "gianfar";
- reg = <0x25000 0x1000>;
- ranges = <0x0 0x25000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <35 2 36 2 40 2>;
- interrupt-parent = <&mpic>;
- tbi-handle = <&tbi1>;
- phy-handle = <&phy1>;
- phy-connection-type = "rgmii-id";
-
- mdio@520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
- };
-
- enet2: ethernet@26000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <2>;
- device_type = "network";
- model = "eTSEC";
- compatible = "gianfar";
- reg = <0x26000 0x1000>;
- ranges = <0x0 0x26000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <31 2 32 2 33 2>;
- interrupt-parent = <&mpic>;
- tbi-handle = <&tbi2>;
- phy-handle = <&phy2>;
- phy-connection-type = "rgmii-id";
-
- mdio@520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x520 0x20>;
-
- tbi2: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
- };
-
- enet3: ethernet@27000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <3>;
- device_type = "network";
- model = "eTSEC";
- compatible = "gianfar";
- reg = <0x27000 0x1000>;
- ranges = <0x0 0x27000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <37 2 38 2 39 2>;
- interrupt-parent = <&mpic>;
- tbi-handle = <&tbi3>;
- phy-handle = <&phy3>;
- phy-connection-type = "rgmii-id";
-
- mdio@520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x520 0x20>;
-
- tbi3: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
- };
-
- serial0: serial@4500 {
- cell-index = <0>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4500 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2>;
- interrupt-parent = <&mpic>;
- };
-
- serial1: serial@4600 {
- cell-index = <1>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4600 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2>;
- interrupt-parent = <&mpic>;
- };
-
- global-utilities@e0000 { //global utilities block
- compatible = "fsl,mpc8572-guts";
- reg = <0xe0000 0x1000>;
- fsl,has-rstcr;
- };
-
- msi@41600 {
- compatible = "fsl,mpc8572-msi", "fsl,mpic-msi";
- reg = <0x41600 0x80>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe0 0
- 0xe1 0
- 0xe2 0
- 0xe3 0
- 0xe4 0
- 0xe5 0
- 0xe6 0
- 0xe7 0>;
- interrupt-parent = <&mpic>;
- };
-
- crypto@30000 {
- compatible = "fsl,sec3.0", "fsl,sec2.4", "fsl,sec2.2",
- "fsl,sec2.1", "fsl,sec2.0";
- reg = <0x30000 0x10000>;
- interrupts = <45 2 58 2>;
- interrupt-parent = <&mpic>;
- fsl,num-channels = <4>;
- fsl,channel-fifo-len = <24>;
- fsl,exec-units-mask = <0x9fe>;
- fsl,descriptor-types-mask = <0x3ab0ebf>;
- };
-
- mpic: pic@40000 {
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <2>;
- reg = <0x40000 0x40000>;
- compatible = "chrp,open-pic";
- device_type = "open-pic";
- };
};
- pci0: pcie@fffe08000 {
- compatible = "fsl,mpc8548-pcie";
- device_type = "pci";
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
+ board_pci0: pci0: pcie@fffe08000 {
reg = <0xf 0xffe08000 0 0x1000>;
- bus-range = <0 255>;
ranges = <0x2000000 0x0 0xe0000000 0xc 0x00000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0xf 0xffc00000 0x0 0x00010000>;
- clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <24 2>;
- interrupt-map-mask = <0xff00 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x11 func 0 - PCI slot 1 */
- 0x8800 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8800 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8800 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8800 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 1 - PCI slot 1 */
- 0x8900 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8900 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8900 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8900 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 2 - PCI slot 1 */
- 0x8a00 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8a00 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8a00 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8a00 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 3 - PCI slot 1 */
- 0x8b00 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8b00 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8b00 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8b00 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 4 - PCI slot 1 */
- 0x8c00 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8c00 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8c00 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8c00 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 5 - PCI slot 1 */
- 0x8d00 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8d00 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8d00 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8d00 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 6 - PCI slot 1 */
- 0x8e00 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8e00 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8e00 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8e00 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 7 - PCI slot 1 */
- 0x8f00 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8f00 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8f00 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8f00 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x12 func 0 - PCI slot 2 */
- 0x9000 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9000 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9000 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9000 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 1 - PCI slot 2 */
- 0x9100 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9100 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9100 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9100 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 2 - PCI slot 2 */
- 0x9200 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9200 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9200 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9200 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 3 - PCI slot 2 */
- 0x9300 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9300 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9300 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9300 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 4 - PCI slot 2 */
- 0x9400 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9400 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9400 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9400 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 5 - PCI slot 2 */
- 0x9500 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9500 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9500 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9500 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 6 - PCI slot 2 */
- 0x9600 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9600 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9600 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9600 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 7 - PCI slot 2 */
- 0x9700 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9700 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9700 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9700 0x0 0x0 0x4 &mpic 0x2 0x1
-
- // IDSEL 0x1c USB
- 0xe000 0x0 0x0 0x1 &i8259 0xc 0x2
- 0xe100 0x0 0x0 0x2 &i8259 0x9 0x2
- 0xe200 0x0 0x0 0x3 &i8259 0xa 0x2
- 0xe300 0x0 0x0 0x4 &i8259 0xb 0x2
-
- // IDSEL 0x1d Audio
- 0xe800 0x0 0x0 0x1 &i8259 0x6 0x2
-
- // IDSEL 0x1e Legacy
- 0xf000 0x0 0x0 0x1 &i8259 0x7 0x2
- 0xf100 0x0 0x0 0x1 &i8259 0x7 0x2
-
- // IDSEL 0x1f IDE/SATA
- 0xf800 0x0 0x0 0x1 &i8259 0xe 0x2
- 0xf900 0x0 0x0 0x1 &i8259 0x5 0x2
-
- >;
-
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
ranges = <0x2000000 0x0 0xe0000000
0x2000000 0x0 0xe0000000
0x0 0x20000000
@@ -667,99 +47,14 @@
0x1000000 0x0 0x0
0x1000000 0x0 0x0
0x0 0x10000>;
- uli1575@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- ranges = <0x2000000 0x0 0xe0000000
- 0x2000000 0x0 0xe0000000
- 0x0 0x20000000
-
- 0x1000000 0x0 0x0
- 0x1000000 0x0 0x0
- 0x0 0x10000>;
- isa@1e {
- device_type = "isa";
- #interrupt-cells = <2>;
- #size-cells = <1>;
- #address-cells = <2>;
- reg = <0xf000 0x0 0x0 0x0 0x0>;
- ranges = <0x1 0x0 0x1000000 0x0 0x0
- 0x1000>;
- interrupt-parent = <&i8259>;
-
- i8259: interrupt-controller@20 {
- reg = <0x1 0x20 0x2
- 0x1 0xa0 0x2
- 0x1 0x4d0 0x2>;
- interrupt-controller;
- device_type = "interrupt-controller";
- #address-cells = <0>;
- #interrupt-cells = <2>;
- compatible = "chrp,iic";
- interrupts = <9 2>;
- interrupt-parent = <&mpic>;
- };
-
- i8042@60 {
- #size-cells = <0>;
- #address-cells = <1>;
- reg = <0x1 0x60 0x1 0x1 0x64 0x1>;
- interrupts = <1 3 12 3>;
- interrupt-parent =
- <&i8259>;
-
- keyboard@0 {
- reg = <0x0>;
- compatible = "pnpPNP,303";
- };
-
- mouse@1 {
- reg = <0x1>;
- compatible = "pnpPNP,f03";
- };
- };
-
- rtc@70 {
- compatible = "pnpPNP,b00";
- reg = <0x1 0x70 0x2>;
- };
-
- gpio@400 {
- reg = <0x1 0x400 0x80>;
- };
- };
- };
};
-
};
pci1: pcie@fffe09000 {
- compatible = "fsl,mpc8548-pcie";
- device_type = "pci";
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
reg = <0xf 0xffe09000 0 0x1000>;
- bus-range = <0 255>;
ranges = <0x2000000 0x0 0xe0000000 0xc 0x20000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0xf 0xffc10000 0x0 0x00010000>;
- clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <25 2>;
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0x0 0x0 0x1 &mpic 0x4 0x1
- 0000 0x0 0x0 0x2 &mpic 0x5 0x1
- 0000 0x0 0x0 0x3 &mpic 0x6 0x1
- 0000 0x0 0x0 0x4 &mpic 0x7 0x1
- >;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
ranges = <0x2000000 0x0 0xe0000000
0x2000000 0x0 0xe0000000
0x0 0x20000000
@@ -771,31 +66,10 @@
};
pci2: pcie@fffe0a000 {
- compatible = "fsl,mpc8548-pcie";
- device_type = "pci";
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
reg = <0xf 0xffe0a000 0 0x1000>;
- bus-range = <0 255>;
ranges = <0x2000000 0x0 0xe0000000 0xc 0x40000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0xf 0xffc20000 0x0 0x00010000>;
- clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <26 2>;
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0x0 0x0 0x1 &mpic 0x0 0x1
- 0000 0x0 0x0 0x2 &mpic 0x1 0x1
- 0000 0x0 0x0 0x3 &mpic 0x2 0x1
- 0000 0x0 0x0 0x4 &mpic 0x3 0x1
- >;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
ranges = <0x2000000 0x0 0xe0000000
0x2000000 0x0 0xe0000000
0x0 0x20000000
@@ -806,3 +80,11 @@
};
};
};
+
+/*
+ * mpc8572ds.dtsi must be last to ensure board_pci0 overrides pci0 settings
+ * for interrupt-map & interrupt-map-mask
+ */
+
+/include/ "fsl/mpc8572si-post.dtsi"
+/include/ "mpc8572ds.dtsi"
diff --git a/arch/powerpc/boot/dts/mpc8572ds_camp_core0.dts b/arch/powerpc/boot/dts/mpc8572ds_camp_core0.dts
index 3375c2a..d34d127 100644
--- a/arch/powerpc/boot/dts/mpc8572ds_camp_core0.dts
+++ b/arch/powerpc/boot/dts/mpc8572ds_camp_core0.dts
@@ -14,494 +14,69 @@
* option) any later version.
*/
-/dts-v1/;
+/include/ "mpc8572ds.dts"
+
/ {
model = "fsl,MPC8572DS";
compatible = "fsl,MPC8572DS", "fsl,MPC8572DS-CAMP";
- #address-cells = <1>;
- #size-cells = <1>;
-
- aliases {
- ethernet0 = &enet0;
- ethernet1 = &enet1;
- serial0 = &serial0;
- pci0 = &pci0;
- pci1 = &pci1;
- };
cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
PowerPC,8572@0 {
- device_type = "cpu";
- reg = <0x0>;
- d-cache-line-size = <32>; // 32 bytes
- i-cache-line-size = <32>; // 32 bytes
- d-cache-size = <0x8000>; // L1, 32K
- i-cache-size = <0x8000>; // L1, 32K
- timebase-frequency = <0>;
- bus-frequency = <0>;
- clock-frequency = <0>;
- next-level-cache = <&L2>;
};
-
+ PowerPC,8572@1 {
+ status = "disabled";
+ };
};
- memory {
- device_type = "memory";
- reg = <0x0 0x0>; // Filled by U-Boot
+ localbus@ffe05000 {
+ status = "disabled";
};
soc8572@ffe00000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "soc";
- compatible = "simple-bus";
- ranges = <0x0 0xffe00000 0x100000>;
- bus-frequency = <0>; // Filled out by uboot.
-
- ecm-law@0 {
- compatible = "fsl,ecm-law";
- reg = <0x0 0x1000>;
- fsl,num-laws = <12>;
+ serial@4600 {
+ status = "disabled";
};
-
- ecm@1000 {
- compatible = "fsl,mpc8572-ecm", "fsl,ecm";
- reg = <0x1000 0x1000>;
- interrupts = <17 2>;
- interrupt-parent = <&mpic>;
+ dma@c300 {
+ status = "disabled";
};
-
- memory-controller@2000 {
- compatible = "fsl,mpc8572-memory-controller";
- reg = <0x2000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <18 2>;
+ gpio-controller@f000 {
};
-
- memory-controller@6000 {
- compatible = "fsl,mpc8572-memory-controller";
- reg = <0x6000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <18 2>;
- };
-
- L2: l2-cache-controller@20000 {
- compatible = "fsl,mpc8572-l2-cache-controller";
- reg = <0x20000 0x1000>;
- cache-line-size = <32>; // 32 bytes
+ l2-cache-controller@20000 {
cache-size = <0x80000>; // L2, 512K
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
};
-
- i2c@3000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x3000 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
- dfsrr;
+ ethernet@26000 {
+ status = "disabled";
};
-
- i2c@3100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- compatible = "fsl-i2c";
- reg = <0x3100 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
- dfsrr;
+ mdio@26520 {
+ status = "disabled";
};
-
- dma@21300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8572-dma", "fsl,eloplus-dma";
- reg = <0x21300 0x4>;
- ranges = <0x0 0x21100 0x200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <20 2>;
- };
- dma-channel@80 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupt-parent = <&mpic>;
- interrupts = <21 2>;
- };
- dma-channel@100 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupt-parent = <&mpic>;
- interrupts = <22 2>;
- };
- dma-channel@180 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupt-parent = <&mpic>;
- interrupts = <23 2>;
- };
+ ethernet@27000 {
+ status = "disabled";
};
-
- enet0: ethernet@24000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <0>;
- device_type = "network";
- model = "eTSEC";
- compatible = "gianfar";
- reg = <0x24000 0x1000>;
- ranges = <0x0 0x24000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <29 2 30 2 34 2>;
- interrupt-parent = <&mpic>;
- phy-handle = <&phy0>;
- phy-connection-type = "rgmii-id";
-
- mdio@520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x0>;
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x1>;
- };
- };
+ mdio@27520 {
+ status = "disabled";
};
-
- enet1: ethernet@25000 {
- cell-index = <1>;
- device_type = "network";
- model = "eTSEC";
- compatible = "gianfar";
- reg = <0x25000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <35 2 36 2 40 2>;
- interrupt-parent = <&mpic>;
- phy-handle = <&phy1>;
- phy-connection-type = "rgmii-id";
- };
-
- serial0: serial@4500 {
- cell-index = <0>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4500 0x100>;
- clock-frequency = <0>;
+ pic@40000 {
+ protected-sources = <
+ 31 32 33 37 38 39 /* enet2 enet3 */
+ 76 77 78 79 26 42 /* dma2 pci2 serial*/
+ 0xe4 0xe5 0xe6 0xe7 /* msi */
+ >;
};
msi@41600 {
- compatible = "fsl,mpc8572-msi", "fsl,mpic-msi";
- reg = <0x41600 0x80>;
msi-available-ranges = <0 0x80>;
interrupts = <
0xe0 0
0xe1 0
0xe2 0
0xe3 0>;
- interrupt-parent = <&mpic>;
- };
-
- global-utilities@e0000 { //global utilities block
- compatible = "fsl,mpc8572-guts";
- reg = <0xe0000 0x1000>;
- fsl,has-rstcr;
- };
-
- crypto@30000 {
- compatible = "fsl,sec3.0", "fsl,sec2.4", "fsl,sec2.2",
- "fsl,sec2.1", "fsl,sec2.0";
- reg = <0x30000 0x10000>;
- interrupts = <45 2 58 2>;
- interrupt-parent = <&mpic>;
- fsl,num-channels = <4>;
- fsl,channel-fifo-len = <24>;
- fsl,exec-units-mask = <0x9fe>;
- fsl,descriptor-types-mask = <0x3ab0ebf>;
- };
-
- mpic: pic@40000 {
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <2>;
- reg = <0x40000 0x40000>;
- compatible = "chrp,open-pic";
- device_type = "open-pic";
- protected-sources = <
- 31 32 33 37 38 39 /* enet2 enet3 */
- 76 77 78 79 26 42 /* dma2 pci2 serial*/
- 0xe4 0xe5 0xe6 0xe7 /* msi */
- >;
};
- };
-
- pci0: pcie@ffe08000 {
- compatible = "fsl,mpc8548-pcie";
- device_type = "pci";
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- reg = <0xffe08000 0x1000>;
- bus-range = <0 255>;
- ranges = <0x2000000 0x0 0x80000000 0x80000000 0x0 0x20000000
- 0x1000000 0x0 0x0 0xffc00000 0x0 0x10000>;
- clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <24 2>;
- interrupt-map-mask = <0xff00 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x11 func 0 - PCI slot 1 */
- 0x8800 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8800 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8800 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8800 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 1 - PCI slot 1 */
- 0x8900 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8900 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8900 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8900 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 2 - PCI slot 1 */
- 0x8a00 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8a00 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8a00 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8a00 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 3 - PCI slot 1 */
- 0x8b00 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8b00 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8b00 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8b00 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 4 - PCI slot 1 */
- 0x8c00 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8c00 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8c00 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8c00 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 5 - PCI slot 1 */
- 0x8d00 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8d00 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8d00 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8d00 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 6 - PCI slot 1 */
- 0x8e00 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8e00 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8e00 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8e00 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x11 func 7 - PCI slot 1 */
- 0x8f00 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x8f00 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x8f00 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x8f00 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x12 func 0 - PCI slot 2 */
- 0x9000 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9000 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9000 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9000 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 1 - PCI slot 2 */
- 0x9100 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9100 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9100 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9100 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 2 - PCI slot 2 */
- 0x9200 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9200 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9200 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9200 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 3 - PCI slot 2 */
- 0x9300 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9300 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9300 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9300 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 4 - PCI slot 2 */
- 0x9400 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9400 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9400 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9400 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 5 - PCI slot 2 */
- 0x9500 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9500 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9500 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9500 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 6 - PCI slot 2 */
- 0x9600 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9600 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9600 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9600 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x12 func 7 - PCI slot 2 */
- 0x9700 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x9700 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x9700 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x9700 0x0 0x0 0x4 &mpic 0x2 0x1
-
- // IDSEL 0x1c USB
- 0xe000 0x0 0x0 0x1 &i8259 0xc 0x2
- 0xe100 0x0 0x0 0x2 &i8259 0x9 0x2
- 0xe200 0x0 0x0 0x3 &i8259 0xa 0x2
- 0xe300 0x0 0x0 0x4 &i8259 0xb 0x2
-
- // IDSEL 0x1d Audio
- 0xe800 0x0 0x0 0x1 &i8259 0x6 0x2
-
- // IDSEL 0x1e Legacy
- 0xf000 0x0 0x0 0x1 &i8259 0x7 0x2
- 0xf100 0x0 0x0 0x1 &i8259 0x7 0x2
-
- // IDSEL 0x1f IDE/SATA
- 0xf800 0x0 0x0 0x1 &i8259 0xe 0x2
- 0xf900 0x0 0x0 0x1 &i8259 0x5 0x2
-
- >;
-
- pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- ranges = <0x2000000 0x0 0x80000000
- 0x2000000 0x0 0x80000000
- 0x0 0x20000000
-
- 0x1000000 0x0 0x0
- 0x1000000 0x0 0x0
- 0x0 0x10000>;
- uli1575@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- ranges = <0x2000000 0x0 0x80000000
- 0x2000000 0x0 0x80000000
- 0x0 0x20000000
-
- 0x1000000 0x0 0x0
- 0x1000000 0x0 0x0
- 0x0 0x10000>;
- isa@1e {
- device_type = "isa";
- #interrupt-cells = <2>;
- #size-cells = <1>;
- #address-cells = <2>;
- reg = <0xf000 0x0 0x0 0x0 0x0>;
- ranges = <0x1 0x0 0x1000000 0x0 0x0
- 0x1000>;
- interrupt-parent = <&i8259>;
-
- i8259: interrupt-controller@20 {
- reg = <0x1 0x20 0x2
- 0x1 0xa0 0x2
- 0x1 0x4d0 0x2>;
- interrupt-controller;
- device_type = "interrupt-controller";
- #address-cells = <0>;
- #interrupt-cells = <2>;
- compatible = "chrp,iic";
- interrupts = <9 2>;
- interrupt-parent = <&mpic>;
- };
-
- i8042@60 {
- #size-cells = <0>;
- #address-cells = <1>;
- reg = <0x1 0x60 0x1 0x1 0x64 0x1>;
- interrupts = <1 3 12 3>;
- interrupt-parent =
- <&i8259>;
-
- keyboard@0 {
- reg = <0x0>;
- compatible = "pnpPNP,303";
- };
-
- mouse@1 {
- reg = <0x1>;
- compatible = "pnpPNP,f03";
- };
- };
-
- rtc@70 {
- compatible = "pnpPNP,b00";
- reg = <0x1 0x70 0x2>;
- };
-
- gpio@400 {
- reg = <0x1 0x400 0x80>;
- };
- };
- };
+ timer@42100 {
+ status = "disabled";
};
-
};
-
- pci1: pcie@ffe09000 {
- compatible = "fsl,mpc8548-pcie";
- device_type = "pci";
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- reg = <0xffe09000 0x1000>;
- bus-range = <0 255>;
- ranges = <0x2000000 0x0 0xa0000000 0xa0000000 0x0 0x20000000
- 0x1000000 0x0 0x0 0xffc10000 0x0 0x10000>;
- clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <25 2>;
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0x0 0x0 0x1 &mpic 0x4 0x1
- 0000 0x0 0x0 0x2 &mpic 0x5 0x1
- 0000 0x0 0x0 0x3 &mpic 0x6 0x1
- 0000 0x0 0x0 0x4 &mpic 0x7 0x1
- >;
- pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- ranges = <0x2000000 0x0 0xa0000000
- 0x2000000 0x0 0xa0000000
- 0x0 0x20000000
-
- 0x1000000 0x0 0x0
- 0x1000000 0x0 0x0
- 0x0 0x10000>;
- };
+ pcie@ffe0a000 {
+ status = "disabled";
};
};
diff --git a/arch/powerpc/boot/dts/mpc8572ds_camp_core1.dts b/arch/powerpc/boot/dts/mpc8572ds_camp_core1.dts
index e7b477f..d6a8faf 100644
--- a/arch/powerpc/boot/dts/mpc8572ds_camp_core1.dts
+++ b/arch/powerpc/boot/dts/mpc8572ds_camp_core1.dts
@@ -15,169 +15,74 @@
* option) any later version.
*/
-/dts-v1/;
+/include/ "mpc8572ds.dts"
+
/ {
model = "fsl,MPC8572DS";
compatible = "fsl,MPC8572DS", "fsl,MPC8572DS-CAMP";
- #address-cells = <1>;
- #size-cells = <1>;
-
- aliases {
- ethernet2 = &enet2;
- ethernet3 = &enet3;
- serial0 = &serial0;
- pci2 = &pci2;
- };
cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
+ PowerPC,8572@0 {
+ status = "disabled";
+ };
PowerPC,8572@1 {
- device_type = "cpu";
- reg = <0x1>;
- d-cache-line-size = <32>; // 32 bytes
- i-cache-line-size = <32>; // 32 bytes
- d-cache-size = <0x8000>; // L1, 32K
- i-cache-size = <0x8000>; // L1, 32K
- timebase-frequency = <0>;
- bus-frequency = <0>;
- clock-frequency = <0>;
- next-level-cache = <&L2>;
};
};
- memory {
- device_type = "memory";
- reg = <0x0 0x0>; // Filled by U-Boot
+ localbus@ffe05000 {
+ status = "disabled";
};
soc8572@ffe00000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "soc";
- compatible = "simple-bus";
- ranges = <0x0 0xffe00000 0x100000>;
- bus-frequency = <0>; // Filled out by uboot.
-
- L2: l2-cache-controller@20000 {
- compatible = "fsl,mpc8572-l2-cache-controller";
- reg = <0x20000 0x1000>;
- cache-line-size = <32>; // 32 bytes
- cache-size = <0x80000>; // L2, 512K
- interrupt-parent = <&mpic>;
+ ecm-law@0 {
+ status = "disabled";
};
-
- dma@c300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8572-dma", "fsl,eloplus-dma";
- reg = <0xc300 0x4>;
- ranges = <0x0 0xc100 0x200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <76 2>;
- };
- dma-channel@80 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupt-parent = <&mpic>;
- interrupts = <77 2>;
- };
- dma-channel@100 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupt-parent = <&mpic>;
- interrupts = <78 2>;
- };
- dma-channel@180 {
- compatible = "fsl,mpc8572-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupt-parent = <&mpic>;
- interrupts = <79 2>;
- };
+ ecm@1000 {
+ status = "disabled";
+ };
+ memory-controller@2000 {
+ status = "disabled";
+ };
+ memory-controller@6000 {
+ status = "disabled";
+ };
+ i2c@3000 {
+ status = "disabled";
+ };
+ i2c@3100 {
+ status = "disabled";
+ };
+ serial@4500 {
+ status = "disabled";
+ };
+ gpio-controller@f000 {
+ status = "disabled";
+ };
+ l2-cache-controller@20000 {
+ cache-size = <0x80000>; // L2, 512K
+ };
+ dma@21300 {
+ status = "disabled";
+ };
+ ethernet@24000 {
+ status = "disabled";
};
-
mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- reg = <0x2>;
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- reg = <0x3>;
- };
+ status = "disabled";
};
-
- enet2: ethernet@26000 {
- cell-index = <2>;
- device_type = "network";
- model = "eTSEC";
- compatible = "gianfar";
- reg = <0x26000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <31 2 32 2 33 2>;
- interrupt-parent = <&mpic>;
- phy-handle = <&phy2>;
- phy-connection-type = "rgmii-id";
+ ptp_clock@24e00 {
+ status = "disabled";
};
-
- enet3: ethernet@27000 {
- cell-index = <3>;
- device_type = "network";
- model = "eTSEC";
- compatible = "gianfar";
- reg = <0x27000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <37 2 38 2 39 2>;
- interrupt-parent = <&mpic>;
- phy-handle = <&phy3>;
- phy-connection-type = "rgmii-id";
+ ethernet@25000 {
+ status = "disabled";
};
-
- msi@41600 {
- compatible = "fsl,mpc8572-msi", "fsl,mpic-msi";
- reg = <0x41600 0x80>;
- msi-available-ranges = <0x80 0x80>;
- interrupts = <
- 0xe4 0
- 0xe5 0
- 0xe6 0
- 0xe7 0>;
- interrupt-parent = <&mpic>;
+ mdio@25520 {
+ status = "disabled";
};
-
- serial0: serial@4600 {
- cell-index = <1>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4600 0x100>;
- clock-frequency = <0>;
+ crypto@30000 {
+ status = "disabled";
};
-
- mpic: pic@40000 {
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <2>;
- reg = <0x40000 0x40000>;
- compatible = "chrp,open-pic";
- device_type = "open-pic";
+ pic@40000 {
protected-sources = <
18 16 10 42 45 58 /* MEM L2 mdio serial crypto */
29 30 34 35 36 40 /* enet0 enet1 */
@@ -189,41 +94,25 @@
0xe0 0xe1 0xe2 0xe3 /* msi */
>;
};
- };
-
- pci2: pcie@ffe0a000 {
- compatible = "fsl,mpc8548-pcie";
- device_type = "pci";
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- reg = <0xffe0a000 0x1000>;
- bus-range = <0 255>;
- ranges = <0x2000000 0x0 0xc0000000 0xc0000000 0x0 0x20000000
- 0x1000000 0x0 0x0 0xffc20000 0x0 0x10000>;
- clock-frequency = <33333333>;
- interrupt-parent = <&mpic>;
- interrupts = <26 2>;
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x0 */
- 0000 0x0 0x0 0x1 &mpic 0x0 0x1
- 0000 0x0 0x0 0x2 &mpic 0x1 0x1
- 0000 0x0 0x0 0x3 &mpic 0x2 0x1
- 0000 0x0 0x0 0x4 &mpic 0x3 0x1
- >;
- pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- ranges = <0x2000000 0x0 0xc0000000
- 0x2000000 0x0 0xc0000000
- 0x0 0x20000000
-
- 0x1000000 0x0 0x0
- 0x1000000 0x0 0x0
- 0x0 0x10000>;
+ timer@41100 {
+ status = "disabled";
};
+ msi@41600 {
+ msi-available-ranges = <0x80 0x80>;
+ interrupts = <
+ 0xe4 0
+ 0xe5 0
+ 0xe6 0
+ 0xe7 0>;
+ };
+ global-utilities@e0000 {
+ status = "disabled";
+ };
+ };
+ pcie@ffe08000 {
+ status = "disabled";
+ };
+ pcie@ffe09000 {
+ status = "disabled";
};
};
--
1.7.3.4
^ permalink raw reply related
* [PATCH 12/29] powerpc/85xx: Rework MPC8569MDS device tree
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-11-git-send-email-galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Dropping "fsl,mpc8569-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/fsl/mpc8569si-post.dtsi | 292 ++++++++++++++++++
arch/powerpc/boot/dts/fsl/mpc8569si-pre.dtsi | 64 ++++
arch/powerpc/boot/dts/mpc8569mds.dts | 409 ++-----------------------
3 files changed, 389 insertions(+), 376 deletions(-)
create mode 100644 arch/powerpc/boot/dts/fsl/mpc8569si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/mpc8569si-pre.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/mpc8569si-post.dtsi b/arch/powerpc/boot/dts/fsl/mpc8569si-post.dtsi
new file mode 100644
index 0000000..eb75a18
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/mpc8569si-post.dtsi
@@ -0,0 +1,292 @@
+/*
+ * MPC8569 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8569-elbc", "fsl,elbc", "simple-bus";
+ interrupts = <19 2 0 0>;
+ sleep = <&pmc 0x08000000>;
+};
+
+/* controller at 0xa000 */
+&pci1 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <26 2 0 0>;
+ sleep = <&pmc 0x20000000>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <26 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+ >;
+ };
+};
+
+&rio {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "fsl,mpc8569-rapidio", "fsl,rapidio-delta";
+ interrupts = <48 2 0 0 /* error */
+ 49 2 0 0 /* bell_outb */
+ 50 2 0 0 /* bell_inb */
+ 53 2 0 0 /* msg1_tx */
+ 54 2 0 0 /* msg1_rx */
+ 55 2 0 0 /* msg2_tx */
+ 56 2 0 0 /* msg2_rx */>;
+ sleep = <&pmc 0x00080000>;
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "fsl,mpc8569-immr", "simple-bus";
+ bus-frequency = <0>; // Filled out by uboot.
+
+ ecm-law@0 {
+ compatible = "fsl,ecm-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <10>;
+ };
+
+ ecm@1000 {
+ compatible = "fsl,mpc8569-ecm", "fsl,ecm";
+ reg = <0x1000 0x1000>;
+ interrupts = <17 2 0 0>;
+ };
+
+ memory-controller@2000 {
+ compatible = "fsl,mpc8569-memory-controller";
+ reg = <0x2000 0x1000>;
+ interrupts = <18 2 0 0>;
+ };
+
+ i2c-sleep-nexus {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ sleep = <&pmc 0x00000004>;
+ ranges;
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+
+ };
+
+ duart-sleep-nexus {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ sleep = <&pmc 0x00000002>;
+ ranges;
+
+/include/ "pq3-duart-0.dtsi"
+
+ };
+
+ L2: l2-cache-controller@20000 {
+ compatible = "fsl,mpc8569-l2-cache-controller";
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x80000>; // L2, 512K
+ interrupts = <16 2 0 0>;
+ };
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-esdhc-0.dtsi"
+ sdhc@2e000 {
+ sleep = <&pmc 0x00200000>;
+ };
+
+ par_io@e0100 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xe0100 0x100>;
+ ranges = <0x0 0xe0100 0x100>;
+ device_type = "par_io";
+ };
+
+/include/ "pq3-sec3.1-0.dtsi"
+ crypto@30000 {
+ sleep = <&pmc 0x01000000>;
+ };
+
+/include/ "pq3-mpic.dtsi"
+
+ global-utilities@e0000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8569-guts", "fsl,mpc8548-guts";
+ reg = <0xe0000 0x1000>;
+ ranges = <0 0xe0000 0x1000>;
+ fsl,has-rstcr;
+
+ pmc: power@70 {
+ compatible = "fsl,mpc8569-pmc",
+ "fsl,mpc8548-pmc";
+ reg = <0x70 0x20>;
+ };
+ };
+};
+
+&qe {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "qe";
+ compatible = "fsl,qe";
+ sleep = <&pmc 0x00000800>;
+ brg-frequency = <0>;
+ bus-frequency = <0>;
+ fsl,qe-num-riscs = <4>;
+ fsl,qe-num-snums = <46>;
+
+ qeic: interrupt-controller@80 {
+ interrupt-controller;
+ compatible = "fsl,qe-ic";
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ reg = <0x80 0x80>;
+ interrupts = <46 2 0 0 46 2 0 0>; //high:30 low:30
+ interrupt-parent = <&mpic>;
+ };
+
+ timer@440 {
+ compatible = "fsl,mpc8569-qe-gtm",
+ "fsl,qe-gtm", "fsl,gtm";
+ reg = <0x440 0x40>;
+ interrupts = <12 13 14 15>;
+ interrupt-parent = <&qeic>;
+ /* Filled in by U-Boot */
+ clock-frequency = <0>;
+ };
+
+ spi@4c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc8569-qe-spi", "fsl,spi";
+ reg = <0x4c0 0x40>;
+ cell-index = <0>;
+ interrupts = <2>;
+ interrupt-parent = <&qeic>;
+ };
+
+ spi@500 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ compatible = "fsl,spi";
+ reg = <0x500 0x40>;
+ interrupts = <1>;
+ interrupt-parent = <&qeic>;
+ };
+
+ usb@6c0 {
+ compatible = "fsl,mpc8569-qe-usb",
+ "fsl,mpc8323-qe-usb";
+ reg = <0x6c0 0x40 0x8b00 0x100>;
+ interrupts = <11>;
+ interrupt-parent = <&qeic>;
+ };
+
+ ucc@2000 {
+ cell-index = <1>;
+ reg = <0x2000 0x200>;
+ interrupts = <32>;
+ interrupt-parent = <&qeic>;
+ };
+
+ ucc@2200 {
+ cell-index = <3>;
+ reg = <0x2200 0x200>;
+ interrupts = <34>;
+ interrupt-parent = <&qeic>;
+ };
+
+ ucc@3000 {
+ cell-index = <2>;
+ reg = <0x3000 0x200>;
+ interrupts = <33>;
+ interrupt-parent = <&qeic>;
+ };
+
+ ucc@3200 {
+ cell-index = <4>;
+ reg = <0x3200 0x200>;
+ interrupts = <35>;
+ interrupt-parent = <&qeic>;
+ };
+
+ ucc@3400 {
+ cell-index = <6>;
+ reg = <0x3400 0x200>;
+ interrupts = <41>;
+ interrupt-parent = <&qeic>;
+ };
+
+ ucc@3600 {
+ cell-index = <8>;
+ reg = <0x3600 0x200>;
+ interrupts = <43>;
+ interrupt-parent = <&qeic>;
+ };
+
+ muram@10000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,qe-muram", "fsl,cpm-muram";
+ ranges = <0x0 0x10000 0x20000>;
+
+ data-only@0 {
+ compatible = "fsl,qe-muram-data",
+ "fsl,cpm-muram-data";
+ reg = <0x0 0x20000>;
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/fsl/mpc8569si-pre.dtsi b/arch/powerpc/boot/dts/fsl/mpc8569si-pre.dtsi
new file mode 100644
index 0000000..b07064d
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/mpc8569si-pre.dtsi
@@ -0,0 +1,64 @@
+/*
+ * MPC8569 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+ compatible = "fsl,MPC8569";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ ethernet3 = &enet3;
+ pci1 = &pci1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,8569@0 {
+ device_type = "cpu";
+ reg = <0x0>;
+ next-level-cache = <&L2>;
+ sleep = <&pmc 0x00008000 // core
+ &pmc 0x00004000>; // timebase
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/mpc8569mds.dts b/arch/powerpc/boot/dts/mpc8569mds.dts
index 8b72eaf..976a7f9 100644
--- a/arch/powerpc/boot/dts/mpc8569mds.dts
+++ b/arch/powerpc/boot/dts/mpc8569mds.dts
@@ -9,66 +9,36 @@
* option) any later version.
*/
-/dts-v1/;
+/include/ "fsl/mpc8569si-pre.dtsi"
/ {
model = "MPC8569EMDS";
compatible = "fsl,MPC8569EMDS";
- #address-cells = <1>;
- #size-cells = <1>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
aliases {
- serial0 = &serial0;
- serial1 = &serial1;
- ethernet0 = &enet0;
- ethernet1 = &enet1;
ethernet2 = &enet2;
ethernet3 = &enet3;
ethernet5 = &enet5;
ethernet7 = &enet7;
- pci1 = &pci1;
- rapidio0 = &rio0;
- };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- PowerPC,8569@0 {
- device_type = "cpu";
- reg = <0x0>;
- d-cache-line-size = <32>; // 32 bytes
- i-cache-line-size = <32>; // 32 bytes
- d-cache-size = <0x8000>; // L1, 32K
- i-cache-size = <0x8000>; // L1, 32K
- sleep = <&pmc 0x00008000 // core
- &pmc 0x00004000>; // timebase
- timebase-frequency = <0>;
- bus-frequency = <0>;
- clock-frequency = <0>;
- next-level-cache = <&L2>;
- };
+ rapidio0 = &rio;
};
memory {
device_type = "memory";
};
- localbus@e0005000 {
- #address-cells = <2>;
- #size-cells = <1>;
- compatible = "fsl,mpc8569-elbc", "fsl,elbc", "simple-bus";
- reg = <0xe0005000 0x1000>;
- interrupts = <19 2>;
- interrupt-parent = <&mpic>;
- sleep = <&pmc 0x08000000>;
-
- ranges = <0x0 0x0 0xfe000000 0x02000000
- 0x1 0x0 0xf8000000 0x00008000
- 0x2 0x0 0xf0000000 0x04000000
- 0x3 0x0 0xfc000000 0x00008000
- 0x4 0x0 0xf8008000 0x00008000
- 0x5 0x0 0xf8010000 0x00008000>;
+ lbc: localbus@e0005000 {
+ reg = <0x0 0xe0005000 0x0 0x1000>;
+
+ ranges = <0x0 0x0 0x0 0xfe000000 0x02000000
+ 0x1 0x0 0x0 0xf8000000 0x00008000
+ 0x2 0x0 0x0 0xf0000000 0x04000000
+ 0x3 0x0 0x0 0xfc000000 0x00008000
+ 0x4 0x0 0x0 0xf8008000 0x00008000
+ 0x5 0x0 0x0 0xf8010000 0x00008000>;
nor@0,0 {
#address-cells = <1>;
@@ -133,220 +103,25 @@
};
};
- soc@e0000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "soc";
- compatible = "fsl,mpc8569-immr", "simple-bus";
- ranges = <0x0 0xe0000000 0x100000>;
- bus-frequency = <0>;
-
- ecm-law@0 {
- compatible = "fsl,ecm-law";
- reg = <0x0 0x1000>;
- fsl,num-laws = <10>;
- };
-
- ecm@1000 {
- compatible = "fsl,mpc8569-ecm", "fsl,ecm";
- reg = <0x1000 0x1000>;
- interrupts = <17 2>;
- interrupt-parent = <&mpic>;
- };
-
- memory-controller@2000 {
- compatible = "fsl,mpc8569-memory-controller";
- reg = <0x2000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <18 2>;
- };
+ soc: soc@e0000000 {
+ ranges = <0x0 0x0 0xe0000000 0x100000>;
i2c-sleep-nexus {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "simple-bus";
- sleep = <&pmc 0x00000004>;
- ranges;
-
i2c@3000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x3000 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
- dfsrr;
-
rtc@68 {
compatible = "dallas,ds1374";
reg = <0x68>;
- interrupts = <3 1>;
- interrupt-parent = <&mpic>;
+ interrupts = <3 1 0 0>;
};
};
-
- i2c@3100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- compatible = "fsl-i2c";
- reg = <0x3100 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
- dfsrr;
- };
- };
-
- duart-sleep-nexus {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "simple-bus";
- sleep = <&pmc 0x00000002>;
- ranges;
-
- serial0: serial@4500 {
- cell-index = <0>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4500 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2>;
- interrupt-parent = <&mpic>;
- };
-
- serial1: serial@4600 {
- cell-index = <1>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4600 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2>;
- interrupt-parent = <&mpic>;
- };
- };
-
- L2: l2-cache-controller@20000 {
- compatible = "fsl,mpc8569-l2-cache-controller";
- reg = <0x20000 0x1000>;
- cache-line-size = <32>; // 32 bytes
- cache-size = <0x80000>; // L2, 512K
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- };
-
- dma@21300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8569-dma", "fsl,eloplus-dma";
- reg = <0x21300 0x4>;
- ranges = <0x0 0x21100 0x200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,mpc8569-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <20 2>;
- };
- dma-channel@80 {
- compatible = "fsl,mpc8569-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupt-parent = <&mpic>;
- interrupts = <21 2>;
- };
- dma-channel@100 {
- compatible = "fsl,mpc8569-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupt-parent = <&mpic>;
- interrupts = <22 2>;
- };
- dma-channel@180 {
- compatible = "fsl,mpc8569-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupt-parent = <&mpic>;
- interrupts = <23 2>;
- };
};
- sdhci@2e000 {
- compatible = "fsl,mpc8569-esdhc", "fsl,esdhc";
- reg = <0x2e000 0x1000>;
- interrupts = <72 0x8>;
- interrupt-parent = <&mpic>;
- sleep = <&pmc 0x00200000>;
- /* Filled in by U-Boot */
- clock-frequency = <0>;
+ sdhc@2e000 {
status = "disabled";
sdhci,1-bit-only;
};
- crypto@30000 {
- compatible = "fsl,sec3.1", "fsl,sec3.0", "fsl,sec2.4",
- "fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0";
- reg = <0x30000 0x10000>;
- interrupts = <45 2 58 2>;
- interrupt-parent = <&mpic>;
- fsl,num-channels = <4>;
- fsl,channel-fifo-len = <24>;
- fsl,exec-units-mask = <0xbfe>;
- fsl,descriptor-types-mask = <0x3ab0ebf>;
- sleep = <&pmc 0x01000000>;
- };
-
- mpic: pic@40000 {
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <2>;
- reg = <0x40000 0x40000>;
- compatible = "chrp,open-pic";
- device_type = "open-pic";
- };
-
- msi@41600 {
- compatible = "fsl,mpc8568-msi", "fsl,mpic-msi";
- reg = <0x41600 0x80>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe0 0
- 0xe1 0
- 0xe2 0
- 0xe3 0
- 0xe4 0
- 0xe5 0
- 0xe6 0
- 0xe7 0>;
- interrupt-parent = <&mpic>;
- };
-
- global-utilities@e0000 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8569-guts", "fsl,mpc8548-guts";
- reg = <0xe0000 0x1000>;
- ranges = <0 0xe0000 0x1000>;
- fsl,has-rstcr;
-
- pmc: power@70 {
- compatible = "fsl,mpc8569-pmc",
- "fsl,mpc8548-pmc";
- reg = <0x70 0x20>;
- };
- };
-
par_io@e0100 {
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0xe0100 0x100>;
- ranges = <0x0 0xe0100 0x100>;
- device_type = "par_io";
num-ports = <7>;
qe_pio_e: gpio-controller@80 {
@@ -447,47 +222,11 @@
};
};
- qe@e0080000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "qe";
- compatible = "fsl,qe";
- ranges = <0x0 0xe0080000 0x40000>;
- reg = <0xe0080000 0x480>;
- sleep = <&pmc 0x00000800>;
- brg-frequency = <0>;
- bus-frequency = <0>;
- fsl,qe-num-riscs = <4>;
- fsl,qe-num-snums = <46>;
-
- qeic: interrupt-controller@80 {
- interrupt-controller;
- compatible = "fsl,qe-ic";
- #address-cells = <0>;
- #interrupt-cells = <1>;
- reg = <0x80 0x80>;
- interrupts = <46 2 46 2>; //high:30 low:30
- interrupt-parent = <&mpic>;
- };
-
- timer@440 {
- compatible = "fsl,mpc8569-qe-gtm",
- "fsl,qe-gtm", "fsl,gtm";
- reg = <0x440 0x40>;
- interrupts = <12 13 14 15>;
- interrupt-parent = <&qeic>;
- /* Filled in by U-Boot */
- clock-frequency = <0>;
- };
+ qe: qe@e0080000 {
+ ranges = <0x0 0x0 0xe0080000 0x40000>;
+ reg = <0x0 0xe0080000 0x0 0x480>;
spi@4c0 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,mpc8569-qe-spi", "fsl,spi";
- reg = <0x4c0 0x40>;
- cell-index = <0>;
- interrupts = <2>;
- interrupt-parent = <&qeic>;
gpios = <&qe_pio_e 30 0>;
mode = "cpu-qe";
@@ -499,20 +238,10 @@
};
spi@500 {
- cell-index = <1>;
- compatible = "fsl,spi";
- reg = <0x500 0x40>;
- interrupts = <1>;
- interrupt-parent = <&qeic>;
mode = "cpu";
};
usb@6c0 {
- compatible = "fsl,mpc8569-qe-usb",
- "fsl,mpc8323-qe-usb";
- reg = <0x6c0 0x40 0x8b00 0x100>;
- interrupts = <11>;
- interrupt-parent = <&qeic>;
fsl,fullspeed-clock = "clk5";
fsl,lowspeed-clock = "brg10";
gpios = <&qe_pio_f 3 0 /* USBOE */
@@ -527,10 +256,6 @@
enet0: ucc@2000 {
device_type = "network";
compatible = "ucc_geth";
- cell-index = <1>;
- reg = <0x2000 0x200>;
- interrupts = <32>;
- interrupt-parent = <&qeic>;
local-mac-address = [ 00 00 00 00 00 00 ];
rx-clock-name = "none";
tx-clock-name = "clk12";
@@ -548,35 +273,33 @@
qe_phy0: ethernet-phy@07 {
interrupt-parent = <&mpic>;
- interrupts = <1 1>;
+ interrupts = <1 1 0 0>;
reg = <0x7>;
device_type = "ethernet-phy";
};
qe_phy1: ethernet-phy@01 {
interrupt-parent = <&mpic>;
- interrupts = <2 1>;
+ interrupts = <2 1 0 0>;
reg = <0x1>;
device_type = "ethernet-phy";
};
qe_phy2: ethernet-phy@02 {
interrupt-parent = <&mpic>;
- interrupts = <3 1>;
+ interrupts = <3 1 0 0>;
reg = <0x2>;
device_type = "ethernet-phy";
};
qe_phy3: ethernet-phy@03 {
interrupt-parent = <&mpic>;
- interrupts = <4 1>;
+ interrupts = <4 1 0 0>;
reg = <0x3>;
device_type = "ethernet-phy";
};
qe_phy5: ethernet-phy@04 {
- interrupt-parent = <&mpic>;
reg = <0x04>;
device_type = "ethernet-phy";
};
qe_phy7: ethernet-phy@06 {
- interrupt-parent = <&mpic>;
reg = <0x6>;
device_type = "ethernet-phy";
};
@@ -610,10 +333,6 @@
enet2: ucc@2200 {
device_type = "network";
compatible = "ucc_geth";
- cell-index = <3>;
- reg = <0x2200 0x200>;
- interrupts = <34>;
- interrupt-parent = <&qeic>;
local-mac-address = [ 00 00 00 00 00 00 ];
rx-clock-name = "none";
tx-clock-name = "clk12";
@@ -637,10 +356,6 @@
enet1: ucc@3000 {
device_type = "network";
compatible = "ucc_geth";
- cell-index = <2>;
- reg = <0x3000 0x200>;
- interrupts = <33>;
- interrupt-parent = <&qeic>;
local-mac-address = [ 00 00 00 00 00 00 ];
rx-clock-name = "none";
tx-clock-name = "clk17";
@@ -664,10 +379,6 @@
enet3: ucc@3200 {
device_type = "network";
compatible = "ucc_geth";
- cell-index = <4>;
- reg = <0x3200 0x200>;
- interrupts = <35>;
- interrupt-parent = <&qeic>;
local-mac-address = [ 00 00 00 00 00 00 ];
rx-clock-name = "none";
tx-clock-name = "clk17";
@@ -691,10 +402,6 @@
enet5: ucc@3400 {
device_type = "network";
compatible = "ucc_geth";
- cell-index = <6>;
- reg = <0x3400 0x200>;
- interrupts = <41>;
- interrupt-parent = <&qeic>;
local-mac-address = [ 00 00 00 00 00 00 ];
rx-clock-name = "none";
tx-clock-name = "none";
@@ -706,10 +413,6 @@
enet7: ucc@3600 {
device_type = "network";
compatible = "ucc_geth";
- cell-index = <8>;
- reg = <0x3600 0x200>;
- interrupts = <43>;
- interrupt-parent = <&qeic>;
local-mac-address = [ 00 00 00 00 00 00 ];
rx-clock-name = "none";
tx-clock-name = "none";
@@ -717,50 +420,14 @@
phy-handle = <&qe_phy7>;
phy-connection-type = "sgmii";
};
-
- muram@10000 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,qe-muram", "fsl,cpm-muram";
- ranges = <0x0 0x10000 0x20000>;
-
- data-only@0 {
- compatible = "fsl,qe-muram-data",
- "fsl,cpm-muram-data";
- reg = <0x0 0x20000>;
- };
- };
-
};
/* PCI Express */
pci1: pcie@e000a000 {
- compatible = "fsl,mpc8548-pcie";
- device_type = "pci";
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- reg = <0xe000a000 0x1000>;
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x0 (PEX) */
- 00000 0x0 0x0 0x1 &mpic 0x0 0x1
- 00000 0x0 0x0 0x2 &mpic 0x1 0x1
- 00000 0x0 0x0 0x3 &mpic 0x2 0x1
- 00000 0x0 0x0 0x4 &mpic 0x3 0x1>;
-
- interrupt-parent = <&mpic>;
- interrupts = <26 2>;
- bus-range = <0 255>;
- ranges = <0x2000000 0x0 0xa0000000 0xa0000000 0x0 0x10000000
- 0x1000000 0x0 0x00000000 0xe2800000 0x0 0x00800000>;
- sleep = <&pmc 0x20000000>;
- clock-frequency = <33333333>;
+ reg = <0x0 0xe000a000 0x0 0x1000>;
+ ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x10000000
+ 0x1000000 0x0 0x00000000 0 0xe2800000 0x0 0x00800000>;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
ranges = <0x2000000 0x0 0xa0000000
0x2000000 0x0 0xa0000000
0x0 0x10000000
@@ -771,20 +438,10 @@
};
};
- rio0: rapidio@e00c00000 {
- #address-cells = <2>;
- #size-cells = <2>;
- compatible = "fsl,mpc8569-rapidio", "fsl,rapidio-delta";
- reg = <0xe00c0000 0x20000>;
- ranges = <0x0 0x0 0xc0000000 0x0 0x20000000>;
- interrupts = <48 2 /* error */
- 49 2 /* bell_outb */
- 50 2 /* bell_inb */
- 53 2 /* msg1_tx */
- 54 2 /* msg1_rx */
- 55 2 /* msg2_tx */
- 56 2 /* msg2_rx */>;
- interrupt-parent = <&mpic>;
- sleep = <&pmc 0x00080000>;
+ rio: rapidio@e00c00000 {
+ reg = <0x0 0xe00c0000 0x0 0x20000>;
+ ranges = <0x0 0x0 0x0 0xc0000000 0x0 0x20000000>;
};
};
+
+/include/ "fsl/mpc8569si-post.dtsi"
--
1.7.3.4
^ permalink raw reply related
* [PATCH 11/29] powerpc/85xx: Rework MPC8568MDS device tree
From: Kumar Gala @ 2011-11-17 7:16 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1321514181-28897-10-git-send-email-galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Dropping "fsl,mpc8568-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/fsl/mpc8568si-post.dtsi | 265 ++++++++++++++
arch/powerpc/boot/dts/fsl/mpc8568si-pre.dtsi | 65 ++++
arch/powerpc/boot/dts/mpc8568mds.dts | 480 ++++---------------------
3 files changed, 393 insertions(+), 417 deletions(-)
create mode 100644 arch/powerpc/boot/dts/fsl/mpc8568si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/mpc8568si-pre.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/mpc8568si-post.dtsi b/arch/powerpc/boot/dts/fsl/mpc8568si-post.dtsi
new file mode 100644
index 0000000..6a9cca8
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/mpc8568si-post.dtsi
@@ -0,0 +1,265 @@
+/*
+ * MPC8568 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8568-localbus", "fsl,pq3-localbus", "simple-bus";
+ interrupts = <19 2 0 0>;
+ sleep = <&pmc 0x08000000>;
+};
+
+/* controller at 0x8000 */
+&pci0 {
+ compatible = "fsl,mpc8540-pci";
+ device_type = "pci";
+ interrupts = <24 0x2 0 0>;
+ bus-range = <0 0xff>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ sleep = <&pmc 0x80000000>;
+};
+
+/* controller at 0xa000 */
+&pci1 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <26 2 0 0>;
+ sleep = <&pmc 0x20000000>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <26 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+ >;
+ };
+};
+
+&rio {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "fsl,mpc8568-rapidio", "fsl,rapidio-delta";
+ interrupts = <48 2 0 0 /* error */
+ 49 2 0 0 /* bell_outb */
+ 50 2 0 0 /* bell_inb */
+ 53 2 0 0 /* msg1_tx */
+ 54 2 0 0 /* msg1_rx */
+ 55 2 0 0 /* msg2_tx */
+ 56 2 0 0 /* msg2_rx */>;
+ sleep = <&pmc 0x00080000 /* controller */
+ &pmc 0x00040000>; /* message unit */
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "fsl,mpc8568-immr", "simple-bus";
+ bus-frequency = <0>; // Filled out by uboot.
+
+ ecm-law@0 {
+ compatible = "fsl,ecm-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <10>;
+ };
+
+ ecm@1000 {
+ compatible = "fsl,mpc8568-ecm", "fsl,ecm";
+ reg = <0x1000 0x1000>;
+ interrupts = <17 2 0 0>;
+ };
+
+ memory-controller@2000 {
+ compatible = "fsl,mpc8568-memory-controller";
+ reg = <0x2000 0x1000>;
+ interrupts = <18 2 0 0>;
+ };
+
+ i2c-sleep-nexus {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ sleep = <&pmc 0x00000004>;
+ ranges;
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+
+ };
+
+ duart-sleep-nexus {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ sleep = <&pmc 0x00000002>;
+ ranges;
+
+/include/ "pq3-duart-0.dtsi"
+
+ };
+
+ L2: l2-cache-controller@20000 {
+ compatible = "fsl,mpc8568-l2-cache-controller";
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x80000>; // L2, 512K
+ interrupts = <16 2 0 0>;
+ };
+
+/include/ "pq3-dma-0.dtsi"
+ dma@21300 {
+ sleep = <&pmc 0x00000400>;
+ };
+
+/include/ "pq3-etsec1-0.dtsi"
+ ethernet@24000 {
+ sleep = <&pmc 0x00000080>;
+ };
+
+/include/ "pq3-etsec1-1.dtsi"
+ ethernet@25000 {
+ sleep = <&pmc 0x00000040>;
+ };
+
+ par_io@e0100 {
+ reg = <0xe0100 0x100>;
+ device_type = "par_io";
+ };
+
+/include/ "pq3-sec2.1-0.dtsi"
+ crypto@30000 {
+ sleep = <&pmc 0x01000000>;
+ };
+
+/include/ "pq3-mpic.dtsi"
+
+ global-utilities@e0000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8568-guts", "fsl,mpc8548-guts";
+ reg = <0xe0000 0x1000>;
+ ranges = <0 0xe0000 0x1000>;
+ fsl,has-rstcr;
+
+ pmc: power@70 {
+ compatible = "fsl,mpc8568-pmc",
+ "fsl,mpc8548-pmc";
+ reg = <0x70 0x20>;
+ };
+ };
+};
+
+&qe {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "qe";
+ compatible = "fsl,qe";
+ sleep = <&pmc 0x00000800>;
+ brg-frequency = <0>;
+ bus-frequency = <396000000>;
+ fsl,qe-num-riscs = <2>;
+ fsl,qe-num-snums = <28>;
+
+ qeic: interrupt-controller@80 {
+ interrupt-controller;
+ compatible = "fsl,qe-ic";
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ reg = <0x80 0x80>;
+ interrupts = <46 2 0 0 46 2 0 0>; //high:30 low:30
+ interrupt-parent = <&mpic>;
+ };
+
+ spi@4c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,spi";
+ reg = <0x4c0 0x40>;
+ cell-index = <0>;
+ interrupts = <2>;
+ interrupt-parent = <&qeic>;
+ };
+
+ spi@500 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ compatible = "fsl,spi";
+ reg = <0x500 0x40>;
+ interrupts = <1>;
+ interrupt-parent = <&qeic>;
+ };
+
+ ucc@2000 {
+ cell-index = <1>;
+ reg = <0x2000 0x200>;
+ interrupts = <32>;
+ interrupt-parent = <&qeic>;
+ };
+
+ ucc@3000 {
+ cell-index = <2>;
+ reg = <0x3000 0x200>;
+ interrupts = <33>;
+ interrupt-parent = <&qeic>;
+ };
+
+ muram@10000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,qe-muram", "fsl,cpm-muram";
+ ranges = <0x0 0x10000 0x10000>;
+
+ data-only@0 {
+ compatible = "fsl,qe-muram-data",
+ "fsl,cpm-muram-data";
+ reg = <0x0 0x10000>;
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/fsl/mpc8568si-pre.dtsi b/arch/powerpc/boot/dts/fsl/mpc8568si-pre.dtsi
new file mode 100644
index 0000000..eacd62c
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/mpc8568si-pre.dtsi
@@ -0,0 +1,65 @@
+/*
+ * MPC8568 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+ compatible = "fsl,MPC8568";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ ethernet3 = &enet3;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,8568@0 {
+ device_type = "cpu";
+ reg = <0x0>;
+ next-level-cache = <&L2>;
+ sleep = <&pmc 0x00008000 // core
+ &pmc 0x00004000>; // timebase
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/mpc8568mds.dts b/arch/powerpc/boot/dts/mpc8568mds.dts
index 647daf8..02eaad3 100644
--- a/arch/powerpc/boot/dts/mpc8568mds.dts
+++ b/arch/powerpc/boot/dts/mpc8568mds.dts
@@ -9,60 +9,25 @@
* option) any later version.
*/
-/dts-v1/;
+/include/ "fsl/mpc8568si-pre.dtsi"
/ {
model = "MPC8568EMDS";
compatible = "MPC8568EMDS", "MPC85xxMDS";
- #address-cells = <1>;
- #size-cells = <1>;
aliases {
- ethernet0 = &enet0;
- ethernet1 = &enet1;
- ethernet2 = &enet2;
- ethernet3 = &enet3;
- serial0 = &serial0;
- serial1 = &serial1;
pci0 = &pci0;
pci1 = &pci1;
- rapidio0 = &rio0;
- };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- PowerPC,8568@0 {
- device_type = "cpu";
- reg = <0x0>;
- d-cache-line-size = <32>; // 32 bytes
- i-cache-line-size = <32>; // 32 bytes
- d-cache-size = <0x8000>; // L1, 32K
- i-cache-size = <0x8000>; // L1, 32K
- sleep = <&pmc 0x00008000 // core
- &pmc 0x00004000>; // timebase
- timebase-frequency = <0>;
- bus-frequency = <0>;
- clock-frequency = <0>;
- next-level-cache = <&L2>;
- };
+ rapidio0 = &rio;
};
memory {
device_type = "memory";
- reg = <0x0 0x10000000>;
+ reg = <0x0 0x0 0x0 0x0>;
};
- localbus@e0005000 {
- #address-cells = <2>;
- #size-cells = <1>;
- compatible = "fsl,mpc8568-localbus", "fsl,pq3-localbus",
- "simple-bus";
- reg = <0xe0005000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <19 2>;
-
+ lbc: localbus@e0005000 {
+ reg = <0x0 0xe0005000 0x0 0x1000>;
ranges = <0x0 0x0 0xfe000000 0x02000000
0x1 0x0 0xf8000000 0x00008000
0x2 0x0 0xf0000000 0x04000000
@@ -104,288 +69,65 @@
};
};
- soc8568@e0000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "soc";
- compatible = "simple-bus";
- ranges = <0x0 0xe0000000 0x100000>;
- bus-frequency = <0>;
-
- ecm-law@0 {
- compatible = "fsl,ecm-law";
- reg = <0x0 0x1000>;
- fsl,num-laws = <10>;
- };
-
- ecm@1000 {
- compatible = "fsl,mpc8568-ecm", "fsl,ecm";
- reg = <0x1000 0x1000>;
- interrupts = <17 2>;
- interrupt-parent = <&mpic>;
- };
-
- memory-controller@2000 {
- compatible = "fsl,mpc8568-memory-controller";
- reg = <0x2000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <18 2>;
- };
-
- L2: l2-cache-controller@20000 {
- compatible = "fsl,mpc8568-l2-cache-controller";
- reg = <0x20000 0x1000>;
- cache-line-size = <32>; // 32 bytes
- cache-size = <0x80000>; // L2, 512K
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- };
+ soc: soc8568@e0000000 {
+ ranges = <0x0 0x0 0xe0000000 0x100000>;
i2c-sleep-nexus {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "simple-bus";
- sleep = <&pmc 0x00000004>;
- ranges;
-
i2c@3000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x3000 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
- dfsrr;
-
rtc@68 {
compatible = "dallas,ds1374";
reg = <0x68>;
- interrupts = <3 1>;
- interrupt-parent = <&mpic>;
+ interrupts = <3 1 0 0>;
};
};
+ };
- i2c@3100 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- compatible = "fsl-i2c";
- reg = <0x3100 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
- dfsrr;
- };
+ enet0: ethernet@24000 {
+ tbi-handle = <&tbi0>;
+ phy-handle = <&phy2>;
};
- dma@21300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8568-dma", "fsl,eloplus-dma";
- reg = <0x21300 0x4>;
- ranges = <0x0 0x21100 0x200>;
- cell-index = <0>;
- sleep = <&pmc 0x00000400>;
-
- dma-channel@0 {
- compatible = "fsl,mpc8568-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <20 2>;
+ mdio@24520 {
+ phy0: ethernet-phy@7 {
+ interrupts = <1 1 0 0>;
+ reg = <0x7>;
+ device_type = "ethernet-phy";
};
- dma-channel@80 {
- compatible = "fsl,mpc8568-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupt-parent = <&mpic>;
- interrupts = <21 2>;
+ phy1: ethernet-phy@1 {
+ interrupts = <2 1 0 0>;
+ reg = <0x1>;
+ device_type = "ethernet-phy";
};
- dma-channel@100 {
- compatible = "fsl,mpc8568-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupt-parent = <&mpic>;
- interrupts = <22 2>;
+ phy2: ethernet-phy@2 {
+ interrupts = <1 1 0 0>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
};
- dma-channel@180 {
- compatible = "fsl,mpc8568-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupt-parent = <&mpic>;
- interrupts = <23 2>;
+ phy3: ethernet-phy@3 {
+ interrupts = <2 1 0 0>;
+ reg = <0x3>;
+ device_type = "ethernet-phy";
};
- };
-
- enet0: ethernet@24000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <0>;
- device_type = "network";
- model = "eTSEC";
- compatible = "gianfar";
- reg = <0x24000 0x1000>;
- ranges = <0x0 0x24000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <29 2 30 2 34 2>;
- interrupt-parent = <&mpic>;
- tbi-handle = <&tbi0>;
- phy-handle = <&phy2>;
- sleep = <&pmc 0x00000080>;
-
- mdio@520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x520 0x20>;
-
- phy0: ethernet-phy@7 {
- interrupt-parent = <&mpic>;
- interrupts = <1 1>;
- reg = <0x7>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <2 1>;
- reg = <0x1>;
- device_type = "ethernet-phy";
- };
- phy2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- interrupts = <1 1>;
- reg = <0x2>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- interrupts = <2 1>;
- reg = <0x3>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
};
};
enet1: ethernet@25000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <1>;
- device_type = "network";
- model = "eTSEC";
- compatible = "gianfar";
- reg = <0x25000 0x1000>;
- ranges = <0x0 0x25000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <35 2 36 2 40 2>;
- interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy3>;
sleep = <&pmc 0x00000040>;
-
- mdio@520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
};
- duart-sleep-nexus {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "simple-bus";
- sleep = <&pmc 0x00000002>;
- ranges;
-
- serial0: serial@4500 {
- cell-index = <0>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4500 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2>;
- interrupt-parent = <&mpic>;
- };
-
- serial1: serial@4600 {
- cell-index = <1>;
- device_type = "serial";
- compatible = "ns16550";
- reg = <0x4600 0x100>;
- clock-frequency = <0>;
- interrupts = <42 2>;
- interrupt-parent = <&mpic>;
+ mdio@25520 {
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
};
};
- global-utilities@e0000 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8568-guts", "fsl,mpc8548-guts";
- reg = <0xe0000 0x1000>;
- ranges = <0 0xe0000 0x1000>;
- fsl,has-rstcr;
-
- pmc: power@70 {
- compatible = "fsl,mpc8568-pmc",
- "fsl,mpc8548-pmc";
- reg = <0x70 0x20>;
- };
- };
-
- crypto@30000 {
- compatible = "fsl,sec2.1", "fsl,sec2.0";
- reg = <0x30000 0x10000>;
- interrupts = <45 2>;
- interrupt-parent = <&mpic>;
- fsl,num-channels = <4>;
- fsl,channel-fifo-len = <24>;
- fsl,exec-units-mask = <0xfe>;
- fsl,descriptor-types-mask = <0x12b0ebf>;
- sleep = <&pmc 0x01000000>;
- };
-
- mpic: pic@40000 {
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <2>;
- reg = <0x40000 0x40000>;
- compatible = "chrp,open-pic";
- device_type = "open-pic";
- };
-
- msi@41600 {
- compatible = "fsl,mpc8568-msi", "fsl,mpic-msi";
- reg = <0x41600 0x80>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe0 0
- 0xe1 0
- 0xe2 0
- 0xe3 0
- 0xe4 0
- 0xe5 0
- 0xe6 0
- 0xe7 0>;
- interrupt-parent = <&mpic>;
- };
-
par_io@e0100 {
- reg = <0xe0100 0x100>;
- device_type = "par_io";
num-ports = <7>;
pio1: ucc_pin@01 {
@@ -448,57 +190,21 @@
};
};
- qe@e0080000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "qe";
- compatible = "fsl,qe";
- ranges = <0x0 0xe0080000 0x40000>;
- reg = <0xe0080000 0x480>;
- sleep = <&pmc 0x00000800>;
- brg-frequency = <0>;
- bus-frequency = <396000000>;
- fsl,qe-num-riscs = <2>;
- fsl,qe-num-snums = <28>;
-
- muram@10000 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,qe-muram", "fsl,cpm-muram";
- ranges = <0x0 0x10000 0x10000>;
-
- data-only@0 {
- compatible = "fsl,qe-muram-data",
- "fsl,cpm-muram-data";
- reg = <0x0 0x10000>;
- };
- };
+ qe: qe@e0080000 {
+ ranges = <0x0 0x0 0xe0080000 0x40000>;
+ reg = <0x0 0xe0080000 0x0 0x480>;
spi@4c0 {
- cell-index = <0>;
- compatible = "fsl,spi";
- reg = <0x4c0 0x40>;
- interrupts = <2>;
- interrupt-parent = <&qeic>;
mode = "cpu";
};
spi@500 {
- cell-index = <1>;
- compatible = "fsl,spi";
- reg = <0x500 0x40>;
- interrupts = <1>;
- interrupt-parent = <&qeic>;
mode = "cpu";
};
enet2: ucc@2000 {
device_type = "network";
compatible = "ucc_geth";
- cell-index = <1>;
- reg = <0x2000 0x200>;
- interrupts = <32>;
- interrupt-parent = <&qeic>;
local-mac-address = [ 00 00 00 00 00 00 ];
rx-clock-name = "none";
tx-clock-name = "clk16";
@@ -510,10 +216,6 @@
enet3: ucc@3000 {
device_type = "network";
compatible = "ucc_geth";
- cell-index = <2>;
- reg = <0x3000 0x200>;
- interrupts = <33>;
- interrupt-parent = <&qeic>;
local-mac-address = [ 00 00 00 00 00 00 ];
rx-clock-name = "none";
tx-clock-name = "clk16";
@@ -532,102 +234,57 @@
* gianfar's MDIO bus */
qe_phy0: ethernet-phy@07 {
interrupt-parent = <&mpic>;
- interrupts = <1 1>;
+ interrupts = <1 1 0 0>;
reg = <0x7>;
device_type = "ethernet-phy";
};
qe_phy1: ethernet-phy@01 {
interrupt-parent = <&mpic>;
- interrupts = <2 1>;
+ interrupts = <2 1 0 0>;
reg = <0x1>;
device_type = "ethernet-phy";
};
qe_phy2: ethernet-phy@02 {
interrupt-parent = <&mpic>;
- interrupts = <1 1>;
+ interrupts = <1 1 0 0>;
reg = <0x2>;
device_type = "ethernet-phy";
};
qe_phy3: ethernet-phy@03 {
interrupt-parent = <&mpic>;
- interrupts = <2 1>;
+ interrupts = <2 1 0 0>;
reg = <0x3>;
device_type = "ethernet-phy";
};
};
-
- qeic: interrupt-controller@80 {
- interrupt-controller;
- compatible = "fsl,qe-ic";
- #address-cells = <0>;
- #interrupt-cells = <1>;
- reg = <0x80 0x80>;
- big-endian;
- interrupts = <46 2 46 2>; //high:30 low:30
- interrupt-parent = <&mpic>;
- };
-
};
pci0: pci@e0008000 {
+ reg = <0x0 0xe0008000 0x0 0x1000>;
+ ranges = <0x2000000 0x0 0x80000000 0x0 0x80000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0x0 0xe2000000 0x0 0x800000>;
+ clock-frequency = <66666666>;
interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x12 AD18 */
- 0x9000 0x0 0x0 0x1 &mpic 0x5 0x1
- 0x9000 0x0 0x0 0x2 &mpic 0x6 0x1
- 0x9000 0x0 0x0 0x3 &mpic 0x7 0x1
- 0x9000 0x0 0x0 0x4 &mpic 0x4 0x1
+ 0x9000 0x0 0x0 0x1 &mpic 0x5 0x1 0 0
+ 0x9000 0x0 0x0 0x2 &mpic 0x6 0x1 0 0
+ 0x9000 0x0 0x0 0x3 &mpic 0x7 0x1 0 0
+ 0x9000 0x0 0x0 0x4 &mpic 0x4 0x1 0 0
/* IDSEL 0x13 AD19 */
- 0x9800 0x0 0x0 0x1 &mpic 0x6 0x1
- 0x9800 0x0 0x0 0x2 &mpic 0x7 0x1
- 0x9800 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x9800 0x0 0x0 0x4 &mpic 0x5 0x1>;
-
- interrupt-parent = <&mpic>;
- interrupts = <24 2>;
- bus-range = <0 255>;
- ranges = <0x2000000 0x0 0x80000000 0x80000000 0x0 0x20000000
- 0x1000000 0x0 0x0 0xe2000000 0x0 0x800000>;
- sleep = <&pmc 0x80000000>;
- clock-frequency = <66666666>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- reg = <0xe0008000 0x1000>;
- compatible = "fsl,mpc8540-pci";
- device_type = "pci";
+ 0x9800 0x0 0x0 0x1 &mpic 0x6 0x1 0 0
+ 0x9800 0x0 0x0 0x2 &mpic 0x7 0x1 0 0
+ 0x9800 0x0 0x0 0x3 &mpic 0x4 0x1 0 0
+ 0x9800 0x0 0x0 0x4 &mpic 0x5 0x1 0 0>;
};
/* PCI Express */
pci1: pcie@e000a000 {
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
-
- /* IDSEL 0x0 (PEX) */
- 00000 0x0 0x0 0x1 &mpic 0x0 0x1
- 00000 0x0 0x0 0x2 &mpic 0x1 0x1
- 00000 0x0 0x0 0x3 &mpic 0x2 0x1
- 00000 0x0 0x0 0x4 &mpic 0x3 0x1>;
-
- interrupt-parent = <&mpic>;
- interrupts = <26 2>;
- bus-range = <0 255>;
- ranges = <0x2000000 0x0 0xa0000000 0xa0000000 0x0 0x10000000
- 0x1000000 0x0 0x0 0xe2800000 0x0 0x800000>;
- sleep = <&pmc 0x20000000>;
- clock-frequency = <33333333>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- reg = <0xe000a000 0x1000>;
- compatible = "fsl,mpc8548-pcie";
- device_type = "pci";
+ ranges = <0x2000000 0x0 0xa0000000 0x0 0xa0000000 0x0 0x10000000
+ 0x1000000 0x0 0x00000000 0x0 0xe2800000 0x0 0x800000>;
+ reg = <0x0 0xe000a000 0x0 0x1000>;
pcie@0 {
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
ranges = <0x2000000 0x0 0xa0000000
0x2000000 0x0 0xa0000000
0x0 0x10000000
@@ -638,22 +295,9 @@
};
};
- rio0: rapidio@e00c00000 {
- #address-cells = <2>;
- #size-cells = <2>;
- compatible = "fsl,mpc8568-rapidio", "fsl,rapidio-delta";
- reg = <0xe00c0000 0x20000>;
- ranges = <0x0 0x0 0xc0000000 0x0 0x20000000>;
- interrupts = <48 2 /* error */
- 49 2 /* bell_outb */
- 50 2 /* bell_inb */
- 53 2 /* msg1_tx */
- 54 2 /* msg1_rx */
- 55 2 /* msg2_tx */
- 56 2 /* msg2_rx */>;
- interrupt-parent = <&mpic>;
- sleep = <&pmc 0x00080000 /* controller */
- &pmc 0x00040000>; /* message unit */
+ rio: rapidio@e00c00000 {
+ reg = <0x0 0xe00c0000 0x0 0x20000>;
+ ranges = <0x0 0x0 0x0 0xc0000000 0x0 0x20000000>;
};
leds {
@@ -672,3 +316,5 @@
};
};
};
+
+/include/ "fsl/mpc8568si-post.dtsi"
--
1.7.3.4
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox