* Re: [PATCH] powerpc/gpio: Fix the wrong GPIO input data on MPC8572/MPC8536
From: Liu Gang @ 2013-11-22 4:47 UTC (permalink / raw)
To: Scott Wood; +Cc: linux-gpio, linus.walleij, linuxppc-dev, r61911, b07421
In-Reply-To: <1384993966.1403.466.camel@snotra.buserror.net>
On Wed, 2013-11-20 at 18:32 -0600, Scott Wood wrote:
> For userspace value setting, it looks like gpiolib blocks the write if
> the pin if FLAG_IS_OUT is set. This suggests that this is an error
> condition for other uses as well. Though, I notice that
> mpc8xxx_gpio_dir_out() calls gpio_set() before actually changing the
> direction. So it may be useful to avoid races where the wrong value is
> output briefly after the direction is changed (especially in open drain
> situations, where the signal could have a meaningful default even before
> we begin outputting). But that raises the question of how you'd do that
> from userspace, and it also renders the to-be-output value as write-only
> data (until the direction is actually changed), since a readback would
> get the input value instead.
>
> > So maybe it's better to eliminate the effects of the ->data to the
> > input pins when reading the status, regardless of the possible changes
> > of the pins and the data.
> > Do you think so?
>
> Perhaps, but that doesn't require you to modify ->data in the get()
> function.
>
> -Scott
>
I think you considered about this more comprehensive.
I'll update the code without the modification of ->data in the get()
function, and also with the comments from Anatolij.
Best Regards,
Liu Gang
^ permalink raw reply
* [PATCH 2/2] powerpc/eeh: Output PHB diag-data
From: Gavin Shan @ 2013-11-22 8:28 UTC (permalink / raw)
To: linuxppc-dev; +Cc: Gavin Shan
In-Reply-To: <1385108926-10817-1-git-send-email-shangw@linux.vnet.ibm.com>
When hitting frozen PE or fenced PHB, it's always indicative to
have dumped PHB diag-data for further analysis and diagnosis.
However, we never dump that for the cases. The patch intends to
dump PHB diag-data at the backend of eeh_ops::get_log() for PowerNV
platform.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
---
arch/powerpc/platforms/powernv/eeh-ioda.c | 7 ++-----
1 file changed, 2 insertions(+), 5 deletions(-)
diff --git a/arch/powerpc/platforms/powernv/eeh-ioda.c b/arch/powerpc/platforms/powernv/eeh-ioda.c
index be33a16..31320c6 100644
--- a/arch/powerpc/platforms/powernv/eeh-ioda.c
+++ b/arch/powerpc/platforms/powernv/eeh-ioda.c
@@ -588,11 +588,8 @@ static int ioda_eeh_get_log(struct eeh_pe *pe, int severity,
return -EIO;
}
- /*
- * FIXME: We probably need log the error in somewhere.
- * Lets make it up in future.
- */
- /* pr_info("%s", phb->diag.blob); */
+ /* The PHB diag-data is always indicative */
+ pnv_pci_dump_phb_diag_data(hose, phb->diag.blob);
spin_unlock_irqrestore(&phb->lock, flags);
--
1.7.9.5
^ permalink raw reply related
* [PATCH 1/2] powerpc/powernv: Move PHB-diag dump functions around
From: Gavin Shan @ 2013-11-22 8:28 UTC (permalink / raw)
To: linuxppc-dev; +Cc: Gavin Shan
Prior to the completion of PCI enumeration, we actively detects
EEH errors on PCI config cycles and dump PHB diag-data if necessary.
The EEH backend also dumps PHB diag-data in case of frozen PE or
fenced PHB. However, we are using different functions to dump the
PHB diag-data for those 2 cases.
The patch merges the functions for dumping PHB diag-data to one so
that we can avoid duplicate code. Also, we never dump PHB3 diag-data
during PCI config cycles with frozen PE. The patch fixes it as well.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
---
arch/powerpc/platforms/powernv/eeh-ioda.c | 150 +---------------------
arch/powerpc/platforms/powernv/pci.c | 196 ++++++++++++++++++++---------
arch/powerpc/platforms/powernv/pci.h | 3 +
3 files changed, 144 insertions(+), 205 deletions(-)
diff --git a/arch/powerpc/platforms/powernv/eeh-ioda.c b/arch/powerpc/platforms/powernv/eeh-ioda.c
index 02245ce..be33a16 100644
--- a/arch/powerpc/platforms/powernv/eeh-ioda.c
+++ b/arch/powerpc/platforms/powernv/eeh-ioda.c
@@ -681,164 +681,20 @@ static void ioda_eeh_hub_diag(struct pci_controller *hose)
}
}
-static void ioda_eeh_p7ioc_phb_diag(struct pci_controller *hose,
- struct OpalIoPhbErrorCommon *common)
-{
- struct OpalIoP7IOCPhbErrorData *data;
- int i;
-
- data = (struct OpalIoP7IOCPhbErrorData *)common;
-
- pr_info("P7IOC PHB#%x Diag-data (Version: %d)\n\n",
- hose->global_number, common->version);
-
- pr_info(" brdgCtl: %08x\n", data->brdgCtl);
-
- pr_info(" portStatusReg: %08x\n", data->portStatusReg);
- pr_info(" rootCmplxStatus: %08x\n", data->rootCmplxStatus);
- pr_info(" busAgentStatus: %08x\n", data->busAgentStatus);
-
- pr_info(" deviceStatus: %08x\n", data->deviceStatus);
- pr_info(" slotStatus: %08x\n", data->slotStatus);
- pr_info(" linkStatus: %08x\n", data->linkStatus);
- pr_info(" devCmdStatus: %08x\n", data->devCmdStatus);
- pr_info(" devSecStatus: %08x\n", data->devSecStatus);
-
- pr_info(" rootErrorStatus: %08x\n", data->rootErrorStatus);
- pr_info(" uncorrErrorStatus: %08x\n", data->uncorrErrorStatus);
- pr_info(" corrErrorStatus: %08x\n", data->corrErrorStatus);
- pr_info(" tlpHdr1: %08x\n", data->tlpHdr1);
- pr_info(" tlpHdr2: %08x\n", data->tlpHdr2);
- pr_info(" tlpHdr3: %08x\n", data->tlpHdr3);
- pr_info(" tlpHdr4: %08x\n", data->tlpHdr4);
- pr_info(" sourceId: %08x\n", data->sourceId);
-
- pr_info(" errorClass: %016llx\n", data->errorClass);
- pr_info(" correlator: %016llx\n", data->correlator);
- pr_info(" p7iocPlssr: %016llx\n", data->p7iocPlssr);
- pr_info(" p7iocCsr: %016llx\n", data->p7iocCsr);
- pr_info(" lemFir: %016llx\n", data->lemFir);
- pr_info(" lemErrorMask: %016llx\n", data->lemErrorMask);
- pr_info(" lemWOF: %016llx\n", data->lemWOF);
- pr_info(" phbErrorStatus: %016llx\n", data->phbErrorStatus);
- pr_info(" phbFirstErrorStatus: %016llx\n", data->phbFirstErrorStatus);
- pr_info(" phbErrorLog0: %016llx\n", data->phbErrorLog0);
- pr_info(" phbErrorLog1: %016llx\n", data->phbErrorLog1);
- pr_info(" mmioErrorStatus: %016llx\n", data->mmioErrorStatus);
- pr_info(" mmioFirstErrorStatus: %016llx\n", data->mmioFirstErrorStatus);
- pr_info(" mmioErrorLog0: %016llx\n", data->mmioErrorLog0);
- pr_info(" mmioErrorLog1: %016llx\n", data->mmioErrorLog1);
- pr_info(" dma0ErrorStatus: %016llx\n", data->dma0ErrorStatus);
- pr_info(" dma0FirstErrorStatus: %016llx\n", data->dma0FirstErrorStatus);
- pr_info(" dma0ErrorLog0: %016llx\n", data->dma0ErrorLog0);
- pr_info(" dma0ErrorLog1: %016llx\n", data->dma0ErrorLog1);
- pr_info(" dma1ErrorStatus: %016llx\n", data->dma1ErrorStatus);
- pr_info(" dma1FirstErrorStatus: %016llx\n", data->dma1FirstErrorStatus);
- pr_info(" dma1ErrorLog0: %016llx\n", data->dma1ErrorLog0);
- pr_info(" dma1ErrorLog1: %016llx\n", data->dma1ErrorLog1);
-
- for (i = 0; i < OPAL_P7IOC_NUM_PEST_REGS; i++) {
- if ((data->pestA[i] >> 63) == 0 &&
- (data->pestB[i] >> 63) == 0)
- continue;
-
- pr_info(" PE[%3d] PESTA: %016llx\n", i, data->pestA[i]);
- pr_info(" PESTB: %016llx\n", data->pestB[i]);
- }
-}
-
-static void ioda_eeh_phb3_phb_diag(struct pci_controller *hose,
- struct OpalIoPhbErrorCommon *common)
-{
- struct OpalIoPhb3ErrorData *data;
- int i;
-
- data = (struct OpalIoPhb3ErrorData*)common;
- pr_info("PHB3 PHB#%x Diag-data (Version: %d)\n\n",
- hose->global_number, common->version);
-
- pr_info(" brdgCtl: %08x\n", data->brdgCtl);
-
- pr_info(" portStatusReg: %08x\n", data->portStatusReg);
- pr_info(" rootCmplxStatus: %08x\n", data->rootCmplxStatus);
- pr_info(" busAgentStatus: %08x\n", data->busAgentStatus);
-
- pr_info(" deviceStatus: %08x\n", data->deviceStatus);
- pr_info(" slotStatus: %08x\n", data->slotStatus);
- pr_info(" linkStatus: %08x\n", data->linkStatus);
- pr_info(" devCmdStatus: %08x\n", data->devCmdStatus);
- pr_info(" devSecStatus: %08x\n", data->devSecStatus);
-
- pr_info(" rootErrorStatus: %08x\n", data->rootErrorStatus);
- pr_info(" uncorrErrorStatus: %08x\n", data->uncorrErrorStatus);
- pr_info(" corrErrorStatus: %08x\n", data->corrErrorStatus);
- pr_info(" tlpHdr1: %08x\n", data->tlpHdr1);
- pr_info(" tlpHdr2: %08x\n", data->tlpHdr2);
- pr_info(" tlpHdr3: %08x\n", data->tlpHdr3);
- pr_info(" tlpHdr4: %08x\n", data->tlpHdr4);
- pr_info(" sourceId: %08x\n", data->sourceId);
- pr_info(" errorClass: %016llx\n", data->errorClass);
- pr_info(" correlator: %016llx\n", data->correlator);
- pr_info(" nFir: %016llx\n", data->nFir);
- pr_info(" nFirMask: %016llx\n", data->nFirMask);
- pr_info(" nFirWOF: %016llx\n", data->nFirWOF);
- pr_info(" PhbPlssr: %016llx\n", data->phbPlssr);
- pr_info(" PhbCsr: %016llx\n", data->phbCsr);
- pr_info(" lemFir: %016llx\n", data->lemFir);
- pr_info(" lemErrorMask: %016llx\n", data->lemErrorMask);
- pr_info(" lemWOF: %016llx\n", data->lemWOF);
- pr_info(" phbErrorStatus: %016llx\n", data->phbErrorStatus);
- pr_info(" phbFirstErrorStatus: %016llx\n", data->phbFirstErrorStatus);
- pr_info(" phbErrorLog0: %016llx\n", data->phbErrorLog0);
- pr_info(" phbErrorLog1: %016llx\n", data->phbErrorLog1);
- pr_info(" mmioErrorStatus: %016llx\n", data->mmioErrorStatus);
- pr_info(" mmioFirstErrorStatus: %016llx\n", data->mmioFirstErrorStatus);
- pr_info(" mmioErrorLog0: %016llx\n", data->mmioErrorLog0);
- pr_info(" mmioErrorLog1: %016llx\n", data->mmioErrorLog1);
- pr_info(" dma0ErrorStatus: %016llx\n", data->dma0ErrorStatus);
- pr_info(" dma0FirstErrorStatus: %016llx\n", data->dma0FirstErrorStatus);
- pr_info(" dma0ErrorLog0: %016llx\n", data->dma0ErrorLog0);
- pr_info(" dma0ErrorLog1: %016llx\n", data->dma0ErrorLog1);
- pr_info(" dma1ErrorStatus: %016llx\n", data->dma1ErrorStatus);
- pr_info(" dma1FirstErrorStatus: %016llx\n", data->dma1FirstErrorStatus);
- pr_info(" dma1ErrorLog0: %016llx\n", data->dma1ErrorLog0);
- pr_info(" dma1ErrorLog1: %016llx\n", data->dma1ErrorLog1);
-
- for (i = 0; i < OPAL_PHB3_NUM_PEST_REGS; i++) {
- if ((data->pestA[i] >> 63) == 0 &&
- (data->pestB[i] >> 63) == 0)
- continue;
-
- pr_info(" PE[%3d] PESTA: %016llx\n", i, data->pestA[i]);
- pr_info(" PESTB: %016llx\n", data->pestB[i]);
- }
-}
-
static void ioda_eeh_phb_diag(struct pci_controller *hose)
{
struct pnv_phb *phb = hose->private_data;
- struct OpalIoPhbErrorCommon *common;
long rc;
- common = (struct OpalIoPhbErrorCommon *)phb->diag.blob;
- rc = opal_pci_get_phb_diag_data2(phb->opal_id, common, PAGE_SIZE);
+ rc = opal_pci_get_phb_diag_data2(phb->opal_id, phb->diag.blob,
+ PNV_PCI_DIAG_BUF_SIZE);
if (rc != OPAL_SUCCESS) {
pr_warning("%s: Failed to get diag-data for PHB#%x (%ld)\n",
__func__, hose->global_number, rc);
return;
}
- switch (common->ioType) {
- case OPAL_PHB_ERROR_DATA_TYPE_P7IOC:
- ioda_eeh_p7ioc_phb_diag(hose, common);
- break;
- case OPAL_PHB_ERROR_DATA_TYPE_PHB3:
- ioda_eeh_phb3_phb_diag(hose, common);
- break;
- default:
- pr_warning("%s: Unrecognized I/O chip %d\n",
- __func__, common->ioType);
- }
+ pnv_pci_dump_phb_diag_data(hose, phb->diag.blob);
}
static int ioda_eeh_get_phb_pe(struct pci_controller *hose,
diff --git a/arch/powerpc/platforms/powernv/pci.c b/arch/powerpc/platforms/powernv/pci.c
index 4eb33a9..f519cef 100644
--- a/arch/powerpc/platforms/powernv/pci.c
+++ b/arch/powerpc/platforms/powernv/pci.c
@@ -124,77 +124,157 @@ static void pnv_teardown_msi_irqs(struct pci_dev *pdev)
}
#endif /* CONFIG_PCI_MSI */
-static void pnv_pci_dump_p7ioc_diag_data(struct pnv_phb *phb)
+static void pnv_pci_dump_p7ioc_diag_data(struct pci_controller *hose,
+ struct OpalIoPhbErrorCommon *common)
{
- struct OpalIoP7IOCPhbErrorData *data = &phb->diag.p7ioc;
+ struct OpalIoP7IOCPhbErrorData *data;
int i;
- pr_info("PHB %d diagnostic data:\n", phb->hose->global_number);
-
- pr_info(" brdgCtl = 0x%08x\n", data->brdgCtl);
-
- pr_info(" portStatusReg = 0x%08x\n", data->portStatusReg);
- pr_info(" rootCmplxStatus = 0x%08x\n", data->rootCmplxStatus);
- pr_info(" busAgentStatus = 0x%08x\n", data->busAgentStatus);
-
- pr_info(" deviceStatus = 0x%08x\n", data->deviceStatus);
- pr_info(" slotStatus = 0x%08x\n", data->slotStatus);
- pr_info(" linkStatus = 0x%08x\n", data->linkStatus);
- pr_info(" devCmdStatus = 0x%08x\n", data->devCmdStatus);
- pr_info(" devSecStatus = 0x%08x\n", data->devSecStatus);
-
- pr_info(" rootErrorStatus = 0x%08x\n", data->rootErrorStatus);
- pr_info(" uncorrErrorStatus = 0x%08x\n", data->uncorrErrorStatus);
- pr_info(" corrErrorStatus = 0x%08x\n", data->corrErrorStatus);
- pr_info(" tlpHdr1 = 0x%08x\n", data->tlpHdr1);
- pr_info(" tlpHdr2 = 0x%08x\n", data->tlpHdr2);
- pr_info(" tlpHdr3 = 0x%08x\n", data->tlpHdr3);
- pr_info(" tlpHdr4 = 0x%08x\n", data->tlpHdr4);
- pr_info(" sourceId = 0x%08x\n", data->sourceId);
-
- pr_info(" errorClass = 0x%016llx\n", data->errorClass);
- pr_info(" correlator = 0x%016llx\n", data->correlator);
-
- pr_info(" p7iocPlssr = 0x%016llx\n", data->p7iocPlssr);
- pr_info(" p7iocCsr = 0x%016llx\n", data->p7iocCsr);
- pr_info(" lemFir = 0x%016llx\n", data->lemFir);
- pr_info(" lemErrorMask = 0x%016llx\n", data->lemErrorMask);
- pr_info(" lemWOF = 0x%016llx\n", data->lemWOF);
- pr_info(" phbErrorStatus = 0x%016llx\n", data->phbErrorStatus);
- pr_info(" phbFirstErrorStatus = 0x%016llx\n", data->phbFirstErrorStatus);
- pr_info(" phbErrorLog0 = 0x%016llx\n", data->phbErrorLog0);
- pr_info(" phbErrorLog1 = 0x%016llx\n", data->phbErrorLog1);
- pr_info(" mmioErrorStatus = 0x%016llx\n", data->mmioErrorStatus);
- pr_info(" mmioFirstErrorStatus = 0x%016llx\n", data->mmioFirstErrorStatus);
- pr_info(" mmioErrorLog0 = 0x%016llx\n", data->mmioErrorLog0);
- pr_info(" mmioErrorLog1 = 0x%016llx\n", data->mmioErrorLog1);
- pr_info(" dma0ErrorStatus = 0x%016llx\n", data->dma0ErrorStatus);
- pr_info(" dma0FirstErrorStatus = 0x%016llx\n", data->dma0FirstErrorStatus);
- pr_info(" dma0ErrorLog0 = 0x%016llx\n", data->dma0ErrorLog0);
- pr_info(" dma0ErrorLog1 = 0x%016llx\n", data->dma0ErrorLog1);
- pr_info(" dma1ErrorStatus = 0x%016llx\n", data->dma1ErrorStatus);
- pr_info(" dma1FirstErrorStatus = 0x%016llx\n", data->dma1FirstErrorStatus);
- pr_info(" dma1ErrorLog0 = 0x%016llx\n", data->dma1ErrorLog0);
- pr_info(" dma1ErrorLog1 = 0x%016llx\n", data->dma1ErrorLog1);
+ data = (struct OpalIoP7IOCPhbErrorData *)common;
+ pr_info("P7IOC PHB#%d Diag-data (Version: %d)\n\n",
+ hose->global_number, common->version);
+
+ pr_info(" brdgCtl: %08x\n", data->brdgCtl);
+
+ pr_info(" portStatusReg: %08x\n", data->portStatusReg);
+ pr_info(" rootCmplxStatus: %08x\n", data->rootCmplxStatus);
+ pr_info(" busAgentStatus: %08x\n", data->busAgentStatus);
+
+ pr_info(" deviceStatus: %08x\n", data->deviceStatus);
+ pr_info(" slotStatus: %08x\n", data->slotStatus);
+ pr_info(" linkStatus: %08x\n", data->linkStatus);
+ pr_info(" devCmdStatus: %08x\n", data->devCmdStatus);
+ pr_info(" devSecStatus: %08x\n", data->devSecStatus);
+
+ pr_info(" rootErrorStatus: %08x\n", data->rootErrorStatus);
+ pr_info(" uncorrErrorStatus: %08x\n", data->uncorrErrorStatus);
+ pr_info(" corrErrorStatus: %08x\n", data->corrErrorStatus);
+ pr_info(" tlpHdr1: %08x\n", data->tlpHdr1);
+ pr_info(" tlpHdr2: %08x\n", data->tlpHdr2);
+ pr_info(" tlpHdr3: %08x\n", data->tlpHdr3);
+ pr_info(" tlpHdr4: %08x\n", data->tlpHdr4);
+ pr_info(" sourceId: %08x\n", data->sourceId);
+ pr_info(" errorClass: %016llx\n", data->errorClass);
+ pr_info(" correlator: %016llx\n", data->correlator);
+ pr_info(" p7iocPlssr: %016llx\n", data->p7iocPlssr);
+ pr_info(" p7iocCsr: %016llx\n", data->p7iocCsr);
+ pr_info(" lemFir: %016llx\n", data->lemFir);
+ pr_info(" lemErrorMask: %016llx\n", data->lemErrorMask);
+ pr_info(" lemWOF: %016llx\n", data->lemWOF);
+ pr_info(" phbErrorStatus: %016llx\n", data->phbErrorStatus);
+ pr_info(" phbFirstErrorStatus: %016llx\n", data->phbFirstErrorStatus);
+ pr_info(" phbErrorLog0: %016llx\n", data->phbErrorLog0);
+ pr_info(" phbErrorLog1: %016llx\n", data->phbErrorLog1);
+ pr_info(" mmioErrorStatus: %016llx\n", data->mmioErrorStatus);
+ pr_info(" mmioFirstErrorStatus: %016llx\n", data->mmioFirstErrorStatus);
+ pr_info(" mmioErrorLog0: %016llx\n", data->mmioErrorLog0);
+ pr_info(" mmioErrorLog1: %016llx\n", data->mmioErrorLog1);
+ pr_info(" dma0ErrorStatus: %016llx\n", data->dma0ErrorStatus);
+ pr_info(" dma0FirstErrorStatus: %016llx\n", data->dma0FirstErrorStatus);
+ pr_info(" dma0ErrorLog0: %016llx\n", data->dma0ErrorLog0);
+ pr_info(" dma0ErrorLog1: %016llx\n", data->dma0ErrorLog1);
+ pr_info(" dma1ErrorStatus: %016llx\n", data->dma1ErrorStatus);
+ pr_info(" dma1FirstErrorStatus: %016llx\n", data->dma1FirstErrorStatus);
+ pr_info(" dma1ErrorLog0: %016llx\n", data->dma1ErrorLog0);
+ pr_info(" dma1ErrorLog1: %016llx\n", data->dma1ErrorLog1);
for (i = 0; i < OPAL_P7IOC_NUM_PEST_REGS; i++) {
if ((data->pestA[i] >> 63) == 0 &&
(data->pestB[i] >> 63) == 0)
continue;
- pr_info(" PE[%3d] PESTA = 0x%016llx\n", i, data->pestA[i]);
- pr_info(" PESTB = 0x%016llx\n", data->pestB[i]);
+
+ pr_info(" PE[%3d] PESTA: %016llx\n", i, data->pestA[i]);
+ pr_info(" PESTB: %016llx\n", data->pestB[i]);
}
}
-static void pnv_pci_dump_phb_diag_data(struct pnv_phb *phb)
+static void pnv_pci_dump_phb3_diag_data(struct pci_controller *hose,
+ struct OpalIoPhbErrorCommon *common)
{
- switch(phb->model) {
- case PNV_PHB_MODEL_P7IOC:
- pnv_pci_dump_p7ioc_diag_data(phb);
+ struct OpalIoPhb3ErrorData *data;
+ int i;
+
+ data = (struct OpalIoPhb3ErrorData*)common;
+ pr_info("PHB3 PHB#%d Diag-data (Version: %d)\n\n",
+ hose->global_number, common->version);
+
+ pr_info(" brdgCtl: %08x\n", data->brdgCtl);
+
+ pr_info(" portStatusReg: %08x\n", data->portStatusReg);
+ pr_info(" rootCmplxStatus: %08x\n", data->rootCmplxStatus);
+ pr_info(" busAgentStatus: %08x\n", data->busAgentStatus);
+
+ pr_info(" deviceStatus: %08x\n", data->deviceStatus);
+ pr_info(" slotStatus: %08x\n", data->slotStatus);
+ pr_info(" linkStatus: %08x\n", data->linkStatus);
+ pr_info(" devCmdStatus: %08x\n", data->devCmdStatus);
+ pr_info(" devSecStatus: %08x\n", data->devSecStatus);
+
+ pr_info(" rootErrorStatus: %08x\n", data->rootErrorStatus);
+ pr_info(" uncorrErrorStatus: %08x\n", data->uncorrErrorStatus);
+ pr_info(" corrErrorStatus: %08x\n", data->corrErrorStatus);
+ pr_info(" tlpHdr1: %08x\n", data->tlpHdr1);
+ pr_info(" tlpHdr2: %08x\n", data->tlpHdr2);
+ pr_info(" tlpHdr3: %08x\n", data->tlpHdr3);
+ pr_info(" tlpHdr4: %08x\n", data->tlpHdr4);
+ pr_info(" sourceId: %08x\n", data->sourceId);
+ pr_info(" errorClass: %016llx\n", data->errorClass);
+ pr_info(" correlator: %016llx\n", data->correlator);
+
+ pr_info(" nFir: %016llx\n", data->nFir);
+ pr_info(" nFirMask: %016llx\n", data->nFirMask);
+ pr_info(" nFirWOF: %016llx\n", data->nFirWOF);
+ pr_info(" PhbPlssr: %016llx\n", data->phbPlssr);
+ pr_info(" PhbCsr: %016llx\n", data->phbCsr);
+ pr_info(" lemFir: %016llx\n", data->lemFir);
+ pr_info(" lemErrorMask: %016llx\n", data->lemErrorMask);
+ pr_info(" lemWOF: %016llx\n", data->lemWOF);
+ pr_info(" phbErrorStatus: %016llx\n", data->phbErrorStatus);
+ pr_info(" phbFirstErrorStatus: %016llx\n", data->phbFirstErrorStatus);
+ pr_info(" phbErrorLog0: %016llx\n", data->phbErrorLog0);
+ pr_info(" phbErrorLog1: %016llx\n", data->phbErrorLog1);
+ pr_info(" mmioErrorStatus: %016llx\n", data->mmioErrorStatus);
+ pr_info(" mmioFirstErrorStatus: %016llx\n", data->mmioFirstErrorStatus);
+ pr_info(" mmioErrorLog0: %016llx\n", data->mmioErrorLog0);
+ pr_info(" mmioErrorLog1: %016llx\n", data->mmioErrorLog1);
+ pr_info(" dma0ErrorStatus: %016llx\n", data->dma0ErrorStatus);
+ pr_info(" dma0FirstErrorStatus: %016llx\n", data->dma0FirstErrorStatus);
+ pr_info(" dma0ErrorLog0: %016llx\n", data->dma0ErrorLog0);
+ pr_info(" dma0ErrorLog1: %016llx\n", data->dma0ErrorLog1);
+ pr_info(" dma1ErrorStatus: %016llx\n", data->dma1ErrorStatus);
+ pr_info(" dma1FirstErrorStatus: %016llx\n", data->dma1FirstErrorStatus);
+ pr_info(" dma1ErrorLog0: %016llx\n", data->dma1ErrorLog0);
+ pr_info(" dma1ErrorLog1: %016llx\n", data->dma1ErrorLog1);
+
+ for (i = 0; i < OPAL_PHB3_NUM_PEST_REGS; i++) {
+ if ((data->pestA[i] >> 63) == 0 &&
+ (data->pestB[i] >> 63) == 0)
+ continue;
+
+ pr_info(" PE[%3d] PESTA: %016llx\n", i, data->pestA[i]);
+ pr_info(" PESTB: %016llx\n", data->pestB[i]);
+ }
+}
+
+void pnv_pci_dump_phb_diag_data(struct pci_controller *hose,
+ unsigned char *log_buff)
+{
+ struct OpalIoPhbErrorCommon *common;
+
+ if (!hose || !log_buff)
+ return;
+
+ common = (struct OpalIoPhbErrorCommon *)log_buff;
+ switch (common->ioType) {
+ case OPAL_PHB_ERROR_DATA_TYPE_P7IOC:
+ pnv_pci_dump_p7ioc_diag_data(hose, common);
+ break;
+ case OPAL_PHB_ERROR_DATA_TYPE_PHB3:
+ pnv_pci_dump_phb3_diag_data(hose, common);
break;
default:
- pr_warning("PCI %d: Can't decode this PHB diag data\n",
- phb->hose->global_number);
+ pr_warn("%s: Unrecognized ioType %d\n",
+ __func__, common->ioType);
}
}
@@ -222,7 +302,7 @@ static void pnv_pci_handle_eeh_config(struct pnv_phb *phb, u32 pe_no)
* with the normal errors generated when probing empty slots
*/
if (has_diag)
- pnv_pci_dump_phb_diag_data(phb);
+ pnv_pci_dump_phb_diag_data(phb->hose, phb->diag.blob);
else
pr_warning("PCI %d: No diag data available\n",
phb->hose->global_number);
diff --git a/arch/powerpc/platforms/powernv/pci.h b/arch/powerpc/platforms/powernv/pci.h
index 911c24e..9a11ff0 100644
--- a/arch/powerpc/platforms/powernv/pci.h
+++ b/arch/powerpc/platforms/powernv/pci.h
@@ -176,6 +176,7 @@ struct pnv_phb {
union {
unsigned char blob[PNV_PCI_DIAG_BUF_SIZE];
struct OpalIoP7IOCPhbErrorData p7ioc;
+ struct OpalIoPhb3ErrorData phb3;
} diag;
};
@@ -184,6 +185,8 @@ extern struct pci_ops pnv_pci_ops;
extern struct pnv_eeh_ops ioda_eeh_ops;
#endif
+void pnv_pci_dump_phb_diag_data(struct pci_controller *hose,
+ unsigned char *log_buff);
int pnv_pci_cfg_read(struct device_node *dn,
int where, int size, u32 *val);
int pnv_pci_cfg_write(struct device_node *dn,
--
1.7.9.5
^ permalink raw reply related
* [PATCH v2] powerpc/gpio: Fix the wrong GPIO input data on MPC8572/MPC8536
From: Liu Gang @ 2013-11-22 8:12 UTC (permalink / raw)
To: linuxppc-dev, linux-gpio, agust, b07421, linus.walleij; +Cc: Liu Gang, r61911
For MPC8572/MPC8536, the status of GPIOs defined as output
cannot be determined by reading GPDAT register, so the code
use shadow data register instead. But the code may give the
wrong status of GPIOs defined as input under some scenarios:
1. If some pins were configured as inputs and were asserted
high before booting the kernel, the shadow data has been
initialized with those pin values.
2. Some pins have been configured as output first and have
been set to the high value, then reconfigured as input.
The above cases will make the shadow data for those input
pins to be set to high. Then reading the pin status will
always return high even if the actual pin status is low.
The code should eliminate the effects of the shadow data to
the input pins, and the status of those pins should be
read directly from GPDAT.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
---
changes in v2:
- Added more description of the problem.
- Reduced one in_be32() call.
- Do not modify the shadow data.
drivers/gpio/gpio-mpc8xxx.c | 8 ++++++--
1 file changed, 6 insertions(+), 2 deletions(-)
diff --git a/drivers/gpio/gpio-mpc8xxx.c b/drivers/gpio/gpio-mpc8xxx.c
index 914e859..d7d6d72 100644
--- a/drivers/gpio/gpio-mpc8xxx.c
+++ b/drivers/gpio/gpio-mpc8xxx.c
@@ -70,10 +70,14 @@ static int mpc8572_gpio_get(struct gpio_chip *gc, unsigned int gpio)
u32 val;
struct of_mm_gpio_chip *mm = to_of_mm_gpio_chip(gc);
struct mpc8xxx_gpio_chip *mpc8xxx_gc = to_mpc8xxx_gpio_chip(mm);
+ u32 out_mask, out_shadow;
- val = in_be32(mm->regs + GPIO_DAT) & ~in_be32(mm->regs + GPIO_DIR);
+ out_mask = in_be32(mm->regs + GPIO_DIR);
- return (val | mpc8xxx_gc->data) & mpc8xxx_gpio2mask(gpio);
+ val = in_be32(mm->regs + GPIO_DAT) & ~out_mask;
+ out_shadow = mpc8xxx_gc->data & out_mask;
+
+ return (val | out_shadow) & mpc8xxx_gpio2mask(gpio);
}
static int mpc8xxx_gpio_get(struct gpio_chip *gc, unsigned int gpio)
--
1.8.4.1
^ permalink raw reply related
* [PATCH 1/4 v2] powerpc/85xx/dts: add third elo3 dma component
From: Shengzhou Liu @ 2013-11-22 11:12 UTC (permalink / raw)
To: linuxppc-dev, scottwood; +Cc: Liu Gang, Shengzhou Liu
Add elo3-dma-2.dtsi to support the third DMA controller.
This is used on T2080, T4240, etc.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
---
v2: no change
arch/powerpc/boot/dts/fsl/elo3-dma-2.dtsi | 82 +++++++++++++++++++++++++++++++
1 file changed, 82 insertions(+)
create mode 100644 arch/powerpc/boot/dts/fsl/elo3-dma-2.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/elo3-dma-2.dtsi b/arch/powerpc/boot/dts/fsl/elo3-dma-2.dtsi
new file mode 100644
index 0000000..b89d816
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/elo3-dma-2.dtsi
@@ -0,0 +1,82 @@
+/*
+ * QorIQ Elo3 DMA device tree stub [ controller @ offset 0x102300 ]
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+dma2: dma@102300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,elo3-dma";
+ reg = <0x102300 0x4>,
+ <0x102600 0x4>;
+ ranges = <0x0 0x102100 0x500>;
+ dma-channel@0 {
+ compatible = "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ interrupts = <256 2 0 0>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ interrupts = <257 2 0 0>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ interrupts = <258 2 0 0>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ interrupts = <259 2 0 0>;
+ };
+ dma-channel@300 {
+ compatible = "fsl,eloplus-dma-channel";
+ reg = <0x300 0x80>;
+ interrupts = <260 2 0 0>;
+ };
+ dma-channel@380 {
+ compatible = "fsl,eloplus-dma-channel";
+ reg = <0x380 0x80>;
+ interrupts = <261 2 0 0>;
+ };
+ dma-channel@400 {
+ compatible = "fsl,eloplus-dma-channel";
+ reg = <0x400 0x80>;
+ interrupts = <262 2 0 0>;
+ };
+ dma-channel@480 {
+ compatible = "fsl,eloplus-dma-channel";
+ reg = <0x480 0x80>;
+ interrupts = <263 2 0 0>;
+ };
+};
--
1.8.0
^ permalink raw reply related
* [PATCH 3/4 v2] powerpc/fsl-booke: Add initial T208x QDS board support
From: Shengzhou Liu @ 2013-11-22 11:12 UTC (permalink / raw)
To: linuxppc-dev, scottwood; +Cc: Shengzhou Liu
In-Reply-To: <1385118772-15126-1-git-send-email-Shengzhou.Liu@freescale.com>
Add support for Freescale T2080/T2081 QDS Development System Board.
T2081QDS board shares the same PCB with T1040QDS with some differences.
The T2080QDS Development System is a high-performance computing,
evaluation, and development platform that supports T2080 QorIQ
Power Architecture processor, with following major features:
T2080QDS feature overview:
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LV devices
- Two DDR3 memory, 4GB, Dual rank @ 1866 Mbps data rate, and ECC support
Ethernet interfaces:
- Two 1Gbps RGMII on-board ports
- Four 10Gbps XFI on-board cages
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes:
- 16 lanes up to 10.3125GHz
- Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
IFC:
- 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
eSPI:
- Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB)
PCIE:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0)
SATA:
- Two SATA 2.0 ports on-board
SRIO:
- Two Serial RapidIO 2.0 ports up to 5 GHz
eSDHC:
- Supports SD/MMC/eMMC Card
DMA:
- Three 8-channels DMA controllers
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
System Logic:
- QIXIS-II FPGA system controll
Differences between T2080 and T2081:
Feature T2080 T2081
1G Ethernet numbers: 8 6
10G Ethernet numbers: 4 2
SerDes lanes: 16 8
Serial RapidIO,RMan: 2 no
SATA Controller: 2 no
Aurora: yes no
SoC Package: 896-pins 780-pins
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
v2: separate patches per board-related.
arch/powerpc/boot/dts/t2080qds.dts | 57 ++++++++
arch/powerpc/boot/dts/t2081qds.dts | 46 +++++++
arch/powerpc/boot/dts/t208xqds.dtsi | 259 ++++++++++++++++++++++++++++++++++++
arch/powerpc/include/asm/mpc85xx.h | 2 +
4 files changed, 364 insertions(+)
create mode 100644 arch/powerpc/boot/dts/t2080qds.dts
create mode 100644 arch/powerpc/boot/dts/t2081qds.dts
create mode 100644 arch/powerpc/boot/dts/t208xqds.dtsi
diff --git a/arch/powerpc/boot/dts/t2080qds.dts b/arch/powerpc/boot/dts/t2080qds.dts
new file mode 100644
index 0000000..aa1d6d8
--- /dev/null
+++ b/arch/powerpc/boot/dts/t2080qds.dts
@@ -0,0 +1,57 @@
+/*
+ * T2080QDS Device Tree Source
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t208xsi-pre.dtsi"
+/include/ "t208xqds.dtsi"
+
+/ {
+ model = "fsl,T2080QDS";
+ compatible = "fsl,T2080QDS";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ rio: rapidio@ffe0c0000 {
+ reg = <0xf 0xfe0c0000 0 0x11000>;
+
+ port1 {
+ ranges = <0 0 0xc 0x20000000 0 0x10000000>;
+ };
+ port2 {
+ ranges = <0 0 0xc 0x30000000 0 0x10000000>;
+ };
+ };
+};
+
+/include/ "fsl/t2080si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/t2081qds.dts b/arch/powerpc/boot/dts/t2081qds.dts
new file mode 100644
index 0000000..8ec80a7
--- /dev/null
+++ b/arch/powerpc/boot/dts/t2081qds.dts
@@ -0,0 +1,46 @@
+/*
+ * T2081QDS Device Tree Source
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t208xsi-pre.dtsi"
+/include/ "t208xqds.dtsi"
+
+/ {
+ model = "fsl,T2081QDS";
+ compatible = "fsl,T2081QDS";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+};
+
+/include/ "fsl/t2081si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/t208xqds.dtsi b/arch/powerpc/boot/dts/t208xqds.dtsi
new file mode 100644
index 0000000..e5d5930
--- /dev/null
+++ b/arch/powerpc/boot/dts/t208xqds.dtsi
@@ -0,0 +1,259 @@
+/*
+ * T2080/T2081 QDS Device Tree Source
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/ {
+ model = "fsl,T2080QDS";
+ compatible = "fsl,T2080QDS";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ ifc: localbus@ffe124000 {
+ reg = <0xf 0xfe124000 0 0x2000>;
+ ranges = <0 0 0xf 0xe8000000 0x08000000
+ 2 0 0xf 0xff800000 0x00010000
+ 3 0 0xf 0xffdf0000 0x00008000>;
+
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x8000000>;
+
+ bank-width = <2>;
+ device-width = <1>;
+ };
+
+ nand@2,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc-nand";
+ reg = <0x2 0x0 0x10000>;
+
+ partition@0 {
+ /* This location must not be altered */
+ /* 1MB for u-boot Bootloader Image */
+ reg = <0x0 0x00100000>;
+ label = "NAND U-Boot Image";
+ read-only;
+ };
+
+ partition@100000 {
+ /* 1MB for DTB Image */
+ reg = <0x00100000 0x00100000>;
+ label = "NAND DTB Image";
+ };
+
+ partition@200000 {
+ /* 10MB for Linux Kernel Image */
+ reg = <0x00200000 0x00A00000>;
+ label = "NAND Linux Kernel Image";
+ };
+
+ partition@C00000 {
+ /* 500MB for Root file System Image */
+ reg = <0x00c00000 0x1F400000>;
+ label = "NAND RFS Image";
+ };
+ };
+
+ boardctrl: board-control@3,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,paragon-fpga", "fsl,fpga-qixis";
+ reg = <3 0 0x300>;
+ ranges = <0 3 0 0x300>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ dcsr: dcsr@f00000000 {
+ ranges = <0x00000000 0xf 0x00000000 0x01072000>;
+ };
+
+ soc: soc@ffe000000 {
+ ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+ reg = <0xf 0xfe000000 0 0x00001000>;
+ spi@110000 {
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25sl12801";
+ reg = <0>;
+ spi-max-frequency = <40000000>; /* input clock */
+ partition@u-boot {
+ label = "SPI U-Boot";
+ reg = <0x00000000 0x00100000>;
+ read-only;
+ };
+ partition@kernel {
+ label = "SPI Kernel";
+ reg = <0x00100000 0x00500000>;
+ read-only;
+ };
+ partition@dtb {
+ label = "SPI DTB";
+ reg = <0x00600000 0x00100000>;
+ read-only;
+ };
+ partition@fs {
+ label = "SPI File System";
+ reg = <0x00700000 0x00900000>;
+ };
+ };
+
+ flash@1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "sst,sst25wf040";
+ reg = <1>;
+ spi-max-frequency = <40000000>; /* input clock */
+ };
+ };
+
+ i2c@118000 {
+ pca9547@77 {
+ compatible = "nxp,pca9547";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0>;
+
+ eeprom@50 {
+ compatible = "at24,24c256";
+ reg = <0x50>;
+ };
+
+ eeprom@51 {
+ compatible = "at24,24c02";
+ reg = <0x51>;
+ };
+
+ eeprom@57 {
+ compatible = "at24,24c02";
+ reg = <0x57>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds3232";
+ reg = <0x68>;
+ interrupts = <0x1 0x1 0 0>;
+ };
+ };
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x1>;
+
+ eeprom@55 {
+ compatible = "at24,24c02";
+ reg = <0x55>;
+ };
+ };
+ };
+ };
+
+ sdhc@114000 {
+ voltage-ranges = <1800 1800 3300 3300>;
+ };
+ };
+
+ pci0: pcie@ffe240000 {
+ reg = <0xf 0xfe240000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0x0 0x20000000
+ 0x01000000 0 0x00000000 0xf 0xf8000000 0x0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci1: pcie@ffe250000 {
+ reg = <0xf 0xfe250000 0 0x10000>;
+ ranges = <0x02000000 0x0 0xe0000000 0xc 0x20000000 0x0 0x10000000
+ 0x01000000 0x0 0x00000000 0xf 0xf8010000 0x0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci2: pcie@ffe260000 {
+ reg = <0xf 0xfe260000 0 0x1000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x30000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci3: pcie@ffe270000 {
+ reg = <0xf 0xfe270000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x40000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8030000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+};
diff --git a/arch/powerpc/include/asm/mpc85xx.h b/arch/powerpc/include/asm/mpc85xx.h
index 736d4ac..3bef74a 100644
--- a/arch/powerpc/include/asm/mpc85xx.h
+++ b/arch/powerpc/include/asm/mpc85xx.h
@@ -77,6 +77,8 @@
#define SVR_T1020 0x852100
#define SVR_T1021 0x852101
#define SVR_T1022 0x852102
+#define SVR_T2080 0x853000
+#define SVR_T2081 0x853100
#define SVR_8610 0x80A000
#define SVR_8641 0x809000
--
1.8.0
^ permalink raw reply related
* [PATCH 2/4 v2] powerpc/fsl-booke: Add initial device tree support for T2080/T2081
From: Shengzhou Liu @ 2013-11-22 11:12 UTC (permalink / raw)
To: linuxppc-dev, scottwood; +Cc: Shengzhou Liu
In-Reply-To: <1385118772-15126-1-git-send-email-Shengzhou.Liu@freescale.com>
Add initial device tree for T2080/T2081 without DPAA components.
The T2080 SoC includes the following function and features:
- Four dual-threaded 64-bit Power architecture e6500 cores, up to 1.8GHz
- 2MB L2 cache and 512KB CoreNet platform cache (CPC)
- Hierarchical interconnect fabric
- One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- 16 SerDes lanes up to 10.3125 GHz
- 8 Ethernet interfaces (multiple 1G/2.5G/10G MACs)
- High-speed peripheral interfaces
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0)
- Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
- Additional peripheral interfaces
- Two serial ATA (SATA 2.0) controllers
- Two high-speed USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/SDXC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Three eight-channel DMA engines
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
T2081 personality is a reduced personality of T2080 without SATA, sRIO, RMan,
Aurora, and with less SerDes lanes and ethernet interfaces.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
v2: separate patches per silicon-related.
arch/powerpc/boot/dts/fsl/t2080si-post.dtsi | 406 ++++++++++++++++++++++++++++
arch/powerpc/boot/dts/fsl/t2081si-post.dtsi | 384 ++++++++++++++++++++++++++
arch/powerpc/boot/dts/fsl/t208xsi-pre.dtsi | 100 +++++++
3 files changed, 890 insertions(+)
create mode 100644 arch/powerpc/boot/dts/fsl/t2080si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/t2081si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/t208xsi-pre.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/t2080si-post.dtsi b/arch/powerpc/boot/dts/fsl/t2080si-post.dtsi
new file mode 100644
index 0000000..be3d8de
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t2080si-post.dtsi
@@ -0,0 +1,406 @@
+/*
+ * T2080 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&ifc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc", "simple-bus";
+ interrupts = <25 2 0 0>;
+};
+
+/* controller at 0x240000 */
+&pci0 {
+ compatible = "fsl,t2080-pcie", "fsl,qoriq-pcie-v3.0", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <20 2 0 0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <20 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 40 1 0 0
+ 0000 0 0 2 &mpic 1 1 0 0
+ 0000 0 0 3 &mpic 2 1 0 0
+ 0000 0 0 4 &mpic 3 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x250000 */
+&pci1 {
+ compatible = "fsl,t2080-pcie", "fsl,qoriq-pcie-v3.0", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 0xff>;
+ interrupts = <21 2 0 0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <21 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 41 1 0 0
+ 0000 0 0 2 &mpic 5 1 0 0
+ 0000 0 0 3 &mpic 6 1 0 0
+ 0000 0 0 4 &mpic 7 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x260000 */
+&pci2 {
+ compatible = "fsl,t2080-pcie", "fsl,qoriq-pcie-v3.0", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <22 2 0 0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <22 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 42 1 0 0
+ 0000 0 0 2 &mpic 9 1 0 0
+ 0000 0 0 3 &mpic 10 1 0 0
+ 0000 0 0 4 &mpic 11 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x270000 */
+&pci3 {
+ compatible = "fsl,t2080-pcie", "fsl,qoriq-pcie-v3.0", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <23 2 0 0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <23 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 43 1 0 0
+ 0000 0 0 2 &mpic 0 1 0 0
+ 0000 0 0 3 &mpic 4 1 0 0
+ 0000 0 0 4 &mpic 8 1 0 0
+ >;
+ };
+};
+
+&rio {
+ compatible = "fsl,srio";
+ interrupts = <16 2 1 11>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ port1 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ cell-index = <1>;
+ };
+
+ port2 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ cell-index = <2>;
+ };
+};
+
+&dcsr {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,dcsr", "simple-bus";
+
+ dcsr-epu@0 {
+ compatible = "fsl,t2080-dcsr-epu", "fsl,dcsr-epu";
+ interrupts = <52 2 0 0
+ 84 2 0 0
+ 85 2 0 0
+ 94 2 0 0
+ 95 2 0 0>;
+ reg = <0x0 0x1000>;
+ };
+ dcsr-npc {
+ compatible = "fsl,t2080-dcsr-cnpc", "fsl,dcsr-cnpc";
+ reg = <0x1000 0x1000 0x1002000 0x10000>;
+ };
+ dcsr-nxc@2000 {
+ compatible = "fsl,dcsr-nxc";
+ reg = <0x2000 0x1000>;
+ };
+ dcsr-corenet {
+ compatible = "fsl,dcsr-corenet";
+ reg = <0x8000 0x1000 0x1A000 0x1000>;
+ };
+ dcsr-ocn@11000 {
+ compatible = "fsl,t2080-dcsr-ocn", "fsl,dcsr-ocn";
+ reg = <0x11000 0x1000>;
+ };
+ dcsr-ddr@12000 {
+ compatible = "fsl,dcsr-ddr";
+ dev-handle = <&ddr1>;
+ reg = <0x12000 0x1000>;
+ };
+ dcsr-nal@18000 {
+ compatible = "fsl,t2080-dcsr-nal", "fsl,dcsr-nal";
+ reg = <0x18000 0x1000>;
+ };
+ dcsr-rcpm@22000 {
+ compatible = "fsl,t2080-dcsr-rcpm", "fsl,dcsr-rcpm";
+ reg = <0x22000 0x1000>;
+ };
+ dcsr-snpc@30000 {
+ compatible = "fsl,t2080-dcsr-snpc", "fsl,dcsr-snpc";
+ reg = <0x30000 0x1000 0x1022000 0x10000>;
+ };
+ dcsr-snpc@31000 {
+ compatible = "fsl,t2080-dcsr-snpc", "fsl,dcsr-snpc";
+ reg = <0x31000 0x1000 0x1042000 0x10000>;
+ };
+ dcsr-snpc@32000 {
+ compatible = "fsl,t2080-dcsr-snpc", "fsl,dcsr-snpc";
+ reg = <0x32000 0x1000 0x1062000 0x10000>;
+ };
+ dcsr-cpu-sb-proxy@100000 {
+ compatible = "fsl,dcsr-e6500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu0>;
+ reg = <0x100000 0x1000 0x101000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@108000 {
+ compatible = "fsl,dcsr-e6500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu1>;
+ reg = <0x108000 0x1000 0x109000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@110000 {
+ compatible = "fsl,dcsr-e6500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu2>;
+ reg = <0x110000 0x1000 0x111000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@118000 {
+ compatible = "fsl,dcsr-e6500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu3>;
+ reg = <0x118000 0x1000 0x119000 0x1000>;
+ };
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "simple-bus";
+
+ soc-sram-error {
+ compatible = "fsl,soc-sram-error";
+ interrupts = <16 2 1 29>;
+ };
+
+ corenet-law@0 {
+ compatible = "fsl,corenet-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <32>;
+ };
+
+ ddr1: memory-controller@8000 {
+ compatible = "fsl,qoriq-memory-controller-v4.7",
+ "fsl,qoriq-memory-controller";
+ reg = <0x8000 0x1000>;
+ interrupts = <16 2 1 23>;
+ };
+
+ cpc: l3-cache-controller@10000 {
+ compatible = "fsl,t2080-l3-cache-controller", "cache";
+ reg = <0x10000 0x1000
+ 0x11000 0x1000
+ 0x12000 0x1000>;
+ interrupts = <16 2 1 27
+ 16 2 1 26
+ 16 2 1 25>;
+ };
+
+ corenet-cf@18000 {
+ compatible = "fsl,corenet2-cf";
+ reg = <0x18000 0x1000>;
+ interrupts = <16 2 1 31>;
+ fsl,ccf-num-csdids = <32>;
+ fsl,ccf-num-snoopids = <32>;
+ };
+
+ iommu@20000 {
+ compatible = "fsl,pamu-v1.0", "fsl,pamu";
+ reg = <0x20000 0x6000>;
+ interrupts = <
+ 24 2 0 0
+ 16 2 1 30>;
+ };
+
+/include/ "qoriq-mpic.dtsi"
+
+ guts: global-utilities@e0000 {
+ compatible = "fsl,t2080-device-config", "fsl,qoriq-device-config-2.0";
+ reg = <0xe0000 0xe00>;
+ fsl,has-rstcr;
+ fsl,liodn-bits = <12>;
+ };
+
+ clockgen: global-utilities@e1000 {
+ compatible = "fsl,t2080-clockgen", "fsl,qoriq-clockgen-2.0",
+ "fixed-clock";
+ reg = <0xe1000 0x1000>;
+ clock-output-names = "sysclk";
+ #clock-cells = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pll0: pll0@800 {
+ #clock-cells = <1>;
+ reg = <0x800>;
+ compatible = "fsl,core-pll-clock";
+ clocks = <&clockgen>;
+ clock-output-names = "pll0", "pll0-div2", "pll0-div4";
+ };
+ pll1: pll1@820 {
+ #clock-cells = <1>;
+ reg = <0x820>;
+ compatible = "fsl,core-pll-clock";
+ clocks = <&clockgen>;
+ clock-output-names = "pll1", "pll1-div2", "pll1-div4";
+ };
+ mux0: mux0@0 {
+ #clock-cells = <0>;
+ reg = <0x0>;
+ compatible = "fsl,core-mux-clock";
+ clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
+ <&pll1 0>, <&pll1 1>, <&pll1 2>;
+ clock-names = "pll0_0", "pll0_1", "pll0_2",
+ "pll1_0", "pll1_1", "pll1_2";
+ clock-output-names = "cmux0";
+ };
+ mux1: mux1@20 {
+ #clock-cells = <0>;
+ reg = <0x20>;
+ compatible = "fsl,core-mux-clock";
+ clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
+ <&pll1 0>, <&pll1 1>, <&pll1 2>;
+ clock-names = "pll0_0", "pll0_1", "pll0_2",
+ "pll1_0", "pll1_1", "pll1_2";
+ clock-output-names = "cmux1";
+ };
+ };
+
+ rcpm: global-utilities@e2000 {
+ compatible = "fsl,t2080-rcpm", "fsl,qoriq-rcpm-2.0";
+ reg = <0xe2000 0x1000>;
+ };
+
+ sfp: sfp@e8000 {
+ compatible = "fsl,t2080-sfp";
+ reg = <0xe8000 0x1000>;
+ };
+
+ serdes: serdes@ea000 {
+ compatible = "fsl,t2080-serdes";
+ reg = <0xea000 0x4000>;
+ };
+
+/include/ "elo3-dma-0.dtsi"
+/include/ "elo3-dma-1.dtsi"
+/include/ "elo3-dma-2.dtsi"
+
+/include/ "qoriq-espi-0.dtsi"
+ spi@110000 {
+ fsl,espi-num-chipselects = <4>;
+ };
+
+/include/ "qoriq-esdhc-0.dtsi"
+ sdhc@114000 {
+ compatible = "fsl,t2080-esdhc", "fsl,esdhc";
+ sdhci,auto-cmd12;
+ };
+/include/ "qoriq-i2c-0.dtsi"
+/include/ "qoriq-i2c-1.dtsi"
+/include/ "qoriq-duart-0.dtsi"
+/include/ "qoriq-duart-1.dtsi"
+/include/ "qoriq-gpio-0.dtsi"
+/include/ "qoriq-gpio-1.dtsi"
+/include/ "qoriq-gpio-2.dtsi"
+/include/ "qoriq-gpio-3.dtsi"
+/include/ "qoriq-usb2-mph-0.dtsi"
+ usb0: usb@210000 {
+ compatible = "fsl-usb2-mph-v2.4", "fsl-usb2-mph";
+ phy_type = "utmi";
+ port0;
+ };
+/include/ "qoriq-usb2-dr-0.dtsi"
+ usb1: usb@211000 {
+ compatible = "fsl-usb2-dr-v2.4", "fsl-usb2-dr";
+ dr_mode = "host";
+ phy_type = "utmi";
+ };
+/include/ "qoriq-sata2-0.dtsi"
+/include/ "qoriq-sata2-1.dtsi"
+/include/ "qoriq-sec5.2-0.dtsi"
+
+ L2_1: l2-cache-controller@c20000 {
+ /* Cluster 0 L2 cache */
+ compatible = "fsl,t2080-l2-cache-controller";
+ reg = <0xc20000 0x40000>;
+ next-level-cache = <&cpc>;
+ };
+};
diff --git a/arch/powerpc/boot/dts/fsl/t2081si-post.dtsi b/arch/powerpc/boot/dts/fsl/t2081si-post.dtsi
new file mode 100644
index 0000000..1bd1bb7
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t2081si-post.dtsi
@@ -0,0 +1,384 @@
+/*
+ * T2081 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&ifc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc", "simple-bus";
+ interrupts = <25 2 0 0>;
+};
+
+/* controller at 0x240000 */
+&pci0 {
+ compatible = "fsl,t2081-pcie", "fsl,qoriq-pcie-v3.0", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <20 2 0 0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <20 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 40 1 0 0
+ 0000 0 0 2 &mpic 1 1 0 0
+ 0000 0 0 3 &mpic 2 1 0 0
+ 0000 0 0 4 &mpic 3 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x250000 */
+&pci1 {
+ compatible = "fsl,t2081-pcie", "fsl,qoriq-pcie-v3.0", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 0xff>;
+ interrupts = <21 2 0 0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <21 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 41 1 0 0
+ 0000 0 0 2 &mpic 5 1 0 0
+ 0000 0 0 3 &mpic 6 1 0 0
+ 0000 0 0 4 &mpic 7 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x260000 */
+&pci2 {
+ compatible = "fsl,t2081-pcie", "fsl,qoriq-pcie-v3.0", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <22 2 0 0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <22 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 42 1 0 0
+ 0000 0 0 2 &mpic 9 1 0 0
+ 0000 0 0 3 &mpic 10 1 0 0
+ 0000 0 0 4 &mpic 11 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x270000 */
+&pci3 {
+ compatible = "fsl,t2081-pcie", "fsl,qoriq-pcie-v3.0", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <23 2 0 0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <23 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 43 1 0 0
+ 0000 0 0 2 &mpic 0 1 0 0
+ 0000 0 0 3 &mpic 4 1 0 0
+ 0000 0 0 4 &mpic 8 1 0 0
+ >;
+ };
+};
+
+&dcsr {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,dcsr", "simple-bus";
+
+ dcsr-epu@0 {
+ compatible = "fsl,t2081-dcsr-epu", "fsl,dcsr-epu";
+ interrupts = <52 2 0 0
+ 84 2 0 0
+ 85 2 0 0
+ 94 2 0 0
+ 95 2 0 0>;
+ reg = <0x0 0x1000>;
+ };
+ dcsr-npc {
+ compatible = "fsl,t2081-dcsr-cnpc", "fsl,dcsr-cnpc";
+ reg = <0x1000 0x1000 0x1002000 0x10000>;
+ };
+ dcsr-nxc@2000 {
+ compatible = "fsl,dcsr-nxc";
+ reg = <0x2000 0x1000>;
+ };
+ dcsr-corenet {
+ compatible = "fsl,dcsr-corenet";
+ reg = <0x8000 0x1000 0x1A000 0x1000>;
+ };
+ dcsr-ocn@11000 {
+ compatible = "fsl,t2081-dcsr-ocn", "fsl,dcsr-ocn";
+ reg = <0x11000 0x1000>;
+ };
+ dcsr-ddr@12000 {
+ compatible = "fsl,dcsr-ddr";
+ dev-handle = <&ddr1>;
+ reg = <0x12000 0x1000>;
+ };
+ dcsr-nal@18000 {
+ compatible = "fsl,t2081-dcsr-nal", "fsl,dcsr-nal";
+ reg = <0x18000 0x1000>;
+ };
+ dcsr-rcpm@22000 {
+ compatible = "fsl,t2081-dcsr-rcpm", "fsl,dcsr-rcpm";
+ reg = <0x22000 0x1000>;
+ };
+ dcsr-snpc@30000 {
+ compatible = "fsl,t2081-dcsr-snpc", "fsl,dcsr-snpc";
+ reg = <0x30000 0x1000 0x1022000 0x10000>;
+ };
+ dcsr-snpc@31000 {
+ compatible = "fsl,t2081-dcsr-snpc", "fsl,dcsr-snpc";
+ reg = <0x31000 0x1000 0x1042000 0x10000>;
+ };
+ dcsr-snpc@32000 {
+ compatible = "fsl,t2081-dcsr-snpc", "fsl,dcsr-snpc";
+ reg = <0x32000 0x1000 0x1062000 0x10000>;
+ };
+ dcsr-cpu-sb-proxy@100000 {
+ compatible = "fsl,dcsr-e6500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu0>;
+ reg = <0x100000 0x1000 0x101000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@108000 {
+ compatible = "fsl,dcsr-e6500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu1>;
+ reg = <0x108000 0x1000 0x109000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@110000 {
+ compatible = "fsl,dcsr-e6500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu2>;
+ reg = <0x110000 0x1000 0x111000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@118000 {
+ compatible = "fsl,dcsr-e6500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu3>;
+ reg = <0x118000 0x1000 0x119000 0x1000>;
+ };
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "simple-bus";
+
+ soc-sram-error {
+ compatible = "fsl,soc-sram-error";
+ interrupts = <16 2 1 29>;
+ };
+
+ corenet-law@0 {
+ compatible = "fsl,corenet-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <32>;
+ };
+
+ ddr1: memory-controller@8000 {
+ compatible = "fsl,qoriq-memory-controller-v4.7",
+ "fsl,qoriq-memory-controller";
+ reg = <0x8000 0x1000>;
+ interrupts = <16 2 1 23>;
+ };
+
+ cpc: l3-cache-controller@10000 {
+ compatible = "fsl,t2081-l3-cache-controller", "cache";
+ reg = <0x10000 0x1000
+ 0x11000 0x1000
+ 0x12000 0x1000>;
+ interrupts = <16 2 1 27
+ 16 2 1 26
+ 16 2 1 25>;
+ };
+
+ corenet-cf@18000 {
+ compatible = "fsl,corenet2-cf";
+ reg = <0x18000 0x1000>;
+ interrupts = <16 2 1 31>;
+ fsl,ccf-num-csdids = <32>;
+ fsl,ccf-num-snoopids = <32>;
+ };
+
+ iommu@20000 {
+ compatible = "fsl,pamu-v1.0", "fsl,pamu";
+ reg = <0x20000 0x6000>;
+ interrupts = <
+ 24 2 0 0
+ 16 2 1 30>;
+ };
+
+/include/ "qoriq-mpic.dtsi"
+
+ guts: global-utilities@e0000 {
+ compatible = "fsl,t2081-device-config", "fsl,qoriq-device-config-2.0";
+ reg = <0xe0000 0xe00>;
+ fsl,has-rstcr;
+ fsl,liodn-bits = <12>;
+ };
+
+ clockgen: global-utilities@e1000 {
+ compatible = "fsl,t2081-clockgen", "fsl,qoriq-clockgen-2.0",
+ "fixed-clock";
+ reg = <0xe1000 0x1000>;
+ clock-output-names = "sysclk";
+ #clock-cells = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pll0: pll0@800 {
+ #clock-cells = <1>;
+ reg = <0x800>;
+ compatible = "fsl,core-pll-clock";
+ clocks = <&clockgen>;
+ clock-output-names = "pll0", "pll0-div2", "pll0-div4";
+ };
+ pll1: pll1@820 {
+ #clock-cells = <1>;
+ reg = <0x820>;
+ compatible = "fsl,core-pll-clock";
+ clocks = <&clockgen>;
+ clock-output-names = "pll1", "pll1-div2", "pll1-div4";
+ };
+ mux0: mux0@0 {
+ #clock-cells = <0>;
+ reg = <0x0>;
+ compatible = "fsl,core-mux-clock";
+ clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
+ <&pll1 0>, <&pll1 1>, <&pll1 2>;
+ clock-names = "pll0_0", "pll0_1", "pll0_2",
+ "pll1_0", "pll1_1", "pll1_2";
+ clock-output-names = "cmux0";
+ };
+ mux1: mux1@20 {
+ #clock-cells = <0>;
+ reg = <0x20>;
+ compatible = "fsl,core-mux-clock";
+ clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
+ <&pll1 0>, <&pll1 1>, <&pll1 2>;
+ clock-names = "pll0_0", "pll0_1", "pll0_2",
+ "pll1_0", "pll1_1", "pll1_2";
+ clock-output-names = "cmux1";
+ };
+ };
+
+ rcpm: global-utilities@e2000 {
+ compatible = "fsl,t2081-rcpm", "fsl,qoriq-rcpm-2.0";
+ reg = <0xe2000 0x1000>;
+ };
+
+ sfp: sfp@e8000 {
+ compatible = "fsl,t2081-sfp";
+ reg = <0xe8000 0x1000>;
+ };
+
+ serdes: serdes@ea000 {
+ compatible = "fsl,t2081-serdes";
+ reg = <0xea000 0x4000>;
+ };
+
+/include/ "elo3-dma-0.dtsi"
+/include/ "elo3-dma-1.dtsi"
+/include/ "elo3-dma-2.dtsi"
+
+/include/ "qoriq-espi-0.dtsi"
+ spi@110000 {
+ fsl,espi-num-chipselects = <4>;
+ };
+
+/include/ "qoriq-esdhc-0.dtsi"
+ sdhc@114000 {
+ compatible = "fsl,t2081-esdhc", "fsl,esdhc";
+ sdhci,auto-cmd12;
+ };
+/include/ "qoriq-i2c-0.dtsi"
+/include/ "qoriq-i2c-1.dtsi"
+/include/ "qoriq-duart-0.dtsi"
+/include/ "qoriq-duart-1.dtsi"
+/include/ "qoriq-gpio-0.dtsi"
+/include/ "qoriq-gpio-1.dtsi"
+/include/ "qoriq-gpio-2.dtsi"
+/include/ "qoriq-gpio-3.dtsi"
+/include/ "qoriq-usb2-mph-0.dtsi"
+ usb0: usb@210000 {
+ compatible = "fsl-usb2-mph-v2.4", "fsl-usb2-mph";
+ phy_type = "utmi";
+ port0;
+ };
+/include/ "qoriq-usb2-dr-0.dtsi"
+ usb1: usb@211000 {
+ compatible = "fsl-usb2-dr-v2.4", "fsl-usb2-dr";
+ dr_mode = "host";
+ phy_type = "utmi";
+ };
+/include/ "qoriq-sec5.2-0.dtsi"
+
+ L2_1: l2-cache-controller@c20000 {
+ /* Cluster 0 L2 cache */
+ compatible = "fsl,t2081-l2-cache-controller";
+ reg = <0xc20000 0x40000>;
+ next-level-cache = <&cpc>;
+ };
+};
diff --git a/arch/powerpc/boot/dts/fsl/t208xsi-pre.dtsi b/arch/powerpc/boot/dts/fsl/t208xsi-pre.dtsi
new file mode 100644
index 0000000..1e5d1a4
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t208xsi-pre.dtsi
@@ -0,0 +1,100 @@
+/*
+ * T2080/T2081 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+/include/ "e6500_power_isa.dtsi"
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ ccsr = &soc;
+ dcsr = &dcsr;
+
+ serial0 = &serial0;
+ serial1 = &serial1;
+ serial2 = &serial2;
+ serial3 = &serial3;
+
+ crypto = &crypto;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
+ pci3 = &pci3;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ dma0 = &dma0;
+ dma1 = &dma1;
+ dma2 = &dma2;
+ sdhc = &sdhc;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /*
+ * Temporarily add next-level-cache info in each cpu node so
+ * that uboot can do L2 cache fixup. This can be removed once
+ * u-boot can create cpu node with cache info.
+ */
+ cpu0: PowerPC,e6500@0 {
+ device_type = "cpu";
+ reg = <0 1>;
+ clocks = <&mux0>;
+ next-level-cache = <&L2_1>;
+ };
+ cpu1: PowerPC,e6500@2 {
+ device_type = "cpu";
+ reg = <2 3>;
+ clocks = <&mux0>;
+ next-level-cache = <&L2_1>;
+ };
+ cpu2: PowerPC,e6500@4 {
+ device_type = "cpu";
+ reg = <4 5>;
+ clocks = <&mux0>;
+ next-level-cache = <&L2_1>;
+ };
+ cpu3: PowerPC,e6500@6 {
+ device_type = "cpu";
+ reg = <6 7>;
+ clocks = <&mux0>;
+ next-level-cache = <&L2_1>;
+ };
+ };
+};
--
1.8.0
^ permalink raw reply related
* [PATCH 4/4 v2] powerpc/fsl-booke: Enable T208xQDS board
From: Shengzhou Liu @ 2013-11-22 11:12 UTC (permalink / raw)
To: linuxppc-dev, scottwood; +Cc: Shengzhou Liu
In-Reply-To: <1385118772-15126-1-git-send-email-Shengzhou.Liu@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
v2: add T2081QDS compatible.
arch/powerpc/platforms/85xx/Kconfig | 2 +-
arch/powerpc/platforms/85xx/corenet_generic.c | 4 ++++
2 files changed, 5 insertions(+), 1 deletion(-)
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index 4d46349..b3436f8 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -259,7 +259,7 @@ config CORENET_GENERIC
For 32bit kernel, the following boards are supported:
P2041 RDB, P3041 DS and P4080 DS
For 64bit kernel, the following boards are supported:
- T4240 QDS and B4 QDS
+ T208x QDS, T4240 QDS and B4 QDS
The following boards are supported for both 32bit and 64bit kernel:
P5020 DS and P5040 DS
diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
index fbd871e..77fd71f 100644
--- a/arch/powerpc/platforms/85xx/corenet_generic.c
+++ b/arch/powerpc/platforms/85xx/corenet_generic.c
@@ -102,6 +102,8 @@ static const char * const boards[] __initconst = {
"fsl,P4080DS",
"fsl,P5020DS",
"fsl,P5040DS",
+ "fsl,T2080QDS",
+ "fsl,T2081QDS",
"fsl,T4240QDS",
"fsl,B4860QDS",
"fsl,B4420QDS",
@@ -115,6 +117,8 @@ static const char * const hv_boards[] __initconst = {
"fsl,P4080DS-hv",
"fsl,P5020DS-hv",
"fsl,P5040DS-hv",
+ "fsl,T2080QDS-hv",
+ "fsl,T2081QDS-hv"
"fsl,T4240QDS-hv",
"fsl,B4860QDS-hv",
"fsl,B4420QDS-hv",
--
1.8.0
^ permalink raw reply related
* Re: [PATCH v7 0/4] Add dual-fifo mode support of i.MX ssi
From: Nicolin Chen @ 2013-11-22 16:31 UTC (permalink / raw)
To: vinod.koul, dan.j.williams, s.hauer, timur, shawn.guo, broonie
Cc: mark.rutland, devicetree, alsa-devel, pawel.moll, swarren,
linux-doc, linux-kernel, rob.herring, dmaengine, ijc+devicetree,
linuxppc-dev, linux-arm-kernel
In-Reply-To: <cover.1384352281.git.b42378@freescale.com>
Hi all,
I'm sorry to push this. But this series has been an orphan for a while.
Could any one please receive and foster it?
Thank you.
Nicolin Chen
On Wed, Nov 13, 2013 at 10:55:23PM +0800, Nicolin Chen wrote:
> * ! This series of patches has a direct dependency between them. When
> * ! applying them, we need to apply to one single branch. Otherwise,
> * ! it would break currect branches.
>
> Changelog
> v7:
> * Appended missing Acked-by to all four patches.
> * Sorry that I didn't add them at the first place.
> v6:
> * PATCH-1: Use goto err_firmware instead of return directly.
> *
> * Nothing changes for the other three ack-ed patches
> v5:
> * PATCH-3: Add period size constraint when using dual fifo mode
> *
> * Nothing changes for the other three patches
> v4:
> * PATCH-3: Drop useless register configuration.
> *
> * Nothing changes for the other three patches
> v3:
> * PATCH-1: Add comments to indicate the end of v1 and v2 array.
> * PATCH-3: Use better way to keep watermark as even number.
> *
> * Nothing changes for PATCH-2 and PATCH-4
> v2:
> * Instead of adding rogue scripts to current SDMA driver based on firmware
> * V1, we define the new SDMA firmware as version 2 and bisect the PATCH-1
> * to two patches: The first is to add version check code to the SDMA driver;
> * And the second is to add SSI dual FIFO DMATYPE.
> *
> * Nothing changes for the last two patches.
> v1:
> * SSI can reduce hardware overrun/underrun possibility when using dual
> * fifo mode. To support this mode, we need to first update sdma sciprt
> * list, and then enable dual fifo BIT in SSI driver, and last update DT
> * bindings of i.MX series.
>
> Nicolin Chen (4):
> dma: imx-sdma: Add sdma firmware version 2 support
> dma: imx-sdma: Add new dma type for ssi dual fifo script
> ASoC: fsl_ssi: Add dual fifo mode support
> ARM: dts: imx: use dual-fifo sdma script for ssi
>
> .../devicetree/bindings/dma/fsl-imx-sdma.txt | 1 +
> arch/arm/boot/dts/imx51.dtsi | 4 ++--
> arch/arm/boot/dts/imx53.dtsi | 4 ++--
> arch/arm/boot/dts/imx6qdl.dtsi | 12 +++++-----
> arch/arm/boot/dts/imx6sl.dtsi | 12 +++++-----
> drivers/dma/imx-sdma.c | 19 ++++++++++++++-
> include/linux/platform_data/dma-imx-sdma.h | 5 ++++
> include/linux/platform_data/dma-imx.h | 1 +
> sound/soc/fsl/fsl_ssi.c | 27 +++++++++++++++++++++-
> 9 files changed, 67 insertions(+), 18 deletions(-)
>
> --
> 1.8.4
>
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
^ permalink raw reply
* [PATCH] powerpc 8xx: mfspr SPRN_TBRx in lieu of mftb/mftbu is not supported
From: Christophe Leroy @ 2013-11-22 16:57 UTC (permalink / raw)
To: Benjamin Herrenschmidt, Paul Mackerras
Cc: scottwood, linuxppc-dev, linux-kernel
Commit beb2dc0a7a84be003ce54e98b95d65cc66e6e536 breaks the MPC8xx which seems
to not support using mfspr SPRN_TBRx instead of mftb/mftbu despite
what is written in the reference manual
This patchs revert to the use of mftb/mftbu when CONFIG_8xx is selected
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
diff -ur a/arch/powerpc/boot/util.S b/arch/powerpc/boot/util.S
--- a/arch/powerpc/boot/util.S 2013-11-20 21:54:45.000000000 +0100
+++ b/arch/powerpc/boot/util.S 2013-11-22 17:19:51.880386544 +0100
@@ -71,18 +71,32 @@
add r4,r4,r5
addi r4,r4,-1
divw r4,r4,r5 /* BUS ticks */
+#ifdef CONFIG_8xx
+1: mftbu r5
+ mftb r6
+ mftbu r7
+#else
1: mfspr r5, SPRN_TBRU
mfspr r6, SPRN_TBRL
mfspr r7, SPRN_TBRU
+#endif
cmpw 0,r5,r7
bne 1b /* Get [synced] base time */
addc r9,r6,r4 /* Compute end time */
addze r8,r5
+#ifdef CONFIG_8xx
+2: mftbu r5
+#else
2: mfspr r5, SPRN_TBRU
+#endif
cmpw 0,r5,r8
blt 2b
bgt 3f
+#ifdef CONFIG_8xx
+ mftb r6
+#else
mfspr r6, SPRN_TBRL
+#endif
cmpw 0,r6,r9
blt 2b
3: blr
diff -ur a/arch/powerpc/include/asm/ppc_asm.h b/arch/powerpc/include/asm/ppc_asm.h
--- a/arch/powerpc/include/asm/ppc_asm.h 2013-11-20 21:54:45.000000000 +0100
+++ b/arch/powerpc/include/asm/ppc_asm.h 2013-11-22 17:24:57.839272480 +0100
@@ -438,6 +438,8 @@
cmpwi dest,0; \
beq- 90b; \
END_FTR_SECTION_NESTED(CPU_FTR_CELL_TB_BUG, CPU_FTR_CELL_TB_BUG, 96)
+#elif defined(CONFIG_8xx)
+#define MFTB(dest) mftb dest
#else
#define MFTB(dest) mfspr dest, SPRN_TBRL
#endif
diff -ur a/arch/powerpc/include/asm/reg.h b/arch/powerpc/include/asm/reg.h
--- a/arch/powerpc/include/asm/reg.h 2013-11-20 21:54:45.000000000 +0100
+++ b/arch/powerpc/include/asm/reg.h 2013-11-22 17:27:44.009391916 +0100
@@ -1154,12 +1154,19 @@
#else /* __powerpc64__ */
+#if defined(CONFIG_8xx)
+#define mftbl() ({unsigned long rval; \
+ asm volatile("mftbl %0" : "=r" (rval)); rval;})
+#define mftbu() ({unsigned long rval; \
+ asm volatile("mftbu %0" : "=r" (rval)); rval;})
+#else
#define mftbl() ({unsigned long rval; \
asm volatile("mfspr %0, %1" : "=r" (rval) : \
"i" (SPRN_TBRL)); rval;})
#define mftbu() ({unsigned long rval; \
asm volatile("mfspr %0, %1" : "=r" (rval) : \
"i" (SPRN_TBRU)); rval;})
+#endif
#endif /* !__powerpc64__ */
#define mttbl(v) asm volatile("mttbl %0":: "r"(v))
diff -ur a/arch/powerpc/include/asm/timex.h b/arch/powerpc/include/asm/timex.h
--- a/arch/powerpc/include/asm/timex.h 2013-11-20 21:54:45.000000000 +0100
+++ b/arch/powerpc/include/asm/timex.h 2013-11-22 17:29:31.207016228 +0100
@@ -29,7 +29,11 @@
ret = 0;
__asm__ __volatile__(
+#ifdef CONFIG_8xx
+ "97: mftb %0\n"
+#else
"97: mfspr %0, %2\n"
+#endif
"99:\n"
".section __ftr_fixup,\"a\"\n"
".align 2\n"
@@ -41,7 +45,11 @@
" .long 0\n"
" .long 0\n"
".previous"
+#ifdef CONFIG_8xx
+ : "=r" (ret) : "i" (CPU_FTR_601));
+#else
: "=r" (ret) : "i" (CPU_FTR_601), "i" (SPRN_TBRL));
+#endif
return ret;
#endif
}
diff -ur a/arch/powerpc/kernel/vdso32/gettimeofday.S b/arch/powerpc/kernel/vdso32/gettimeofday.S
--- a/arch/powerpc/kernel/vdso32/gettimeofday.S 2013-11-20 21:54:46.000000000 +0100
+++ b/arch/powerpc/kernel/vdso32/gettimeofday.S 2013-11-22 17:30:53.646493897 +0100
@@ -232,9 +232,15 @@
lwz r6,(CFG_TB_ORIG_STAMP+4)(r9)
/* Get a stable TB value */
+#ifdef CONFIG_8xx
+2: mftbu r3
+ mftbl r4
+ mftbu r0
+#else
2: mfspr r3, SPRN_TBRU
mfspr r4, SPRN_TBRL
mfspr r0, SPRN_TBRU
+#endif
cmplw cr0,r3,r0
bne- 2b
^ permalink raw reply
* [PATCH v2] powerpc 8xx: defconfig: slice by 4 is more efficient than the default slice by 8 on Powerpc 8xx.
From: Christophe Leroy @ 2013-11-22 17:28 UTC (permalink / raw)
To: Benjamin Herrenschmidt, Paul Mackerras
Cc: scottwood, linuxppc-dev, linux-kernel
On PPC_8xx, CRC32_SLICEBY4 is more efficient (almost twice) than CRC32_SLICEBY8,
as shown below:
With CRC32_SLICEBY8:
[ 1.109204] crc32: CRC_LE_BITS = 64, CRC_BE BITS = 64
[ 1.114401] crc32: self tests passed, processed 225944 bytes in 15118910 nsec
[ 1.130655] crc32c: CRC_LE_BITS = 64
[ 1.134235] crc32c: self tests passed, processed 225944 bytes in 4479879 nsec
With CRC32_SLICEBY4:
[ 1.097129] crc32: CRC_LE_BITS = 32, CRC_BE BITS = 32
[ 1.101878] crc32: self tests passed, processed 225944 bytes in 8616242 nsec
[ 1.116298] crc32c: CRC_LE_BITS = 32
[ 1.119607] crc32c: self tests passed, processed 225944 bytes in 3289576 nsec
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
diff -ur a/arch/powerpc/configs/adder875_defconfig b/arch/powerpc/configs.new/adder875_defconfig
--- a/arch/powerpc/configs/adder875_defconfig 2013-11-22 18:20:10.342968268 +0100
+++ b/arch/powerpc/configs.new/adder875_defconfig 2013-11-22 18:17:46.499686457 +0100
@@ -70,3 +70,4 @@
CONFIG_DETECT_HUNG_TASK=y
CONFIG_DEBUG_INFO=y
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+CONFIG_CRC32_SLICEBY4=y
diff -ur a/arch/powerpc/configs/ep88xc_defconfig b/arch/powerpc/configs.new/ep88xc_defconfig
--- a/arch/powerpc/configs/ep88xc_defconfig 2013-11-22 18:20:10.286961148 +0100
+++ b/arch/powerpc/configs.new/ep88xc_defconfig 2013-11-22 18:17:41.992113565 +0100
@@ -72,3 +72,4 @@
CONFIG_DETECT_HUNG_TASK=y
CONFIG_DEBUG_INFO=y
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+CONFIG_CRC32_SLICEBY4=y
diff -ur a/arch/powerpc/configs/mpc866_ads_defconfig b/arch/powerpc/configs.new/mpc866_ads_defconfig
--- a/arch/powerpc/configs/mpc866_ads_defconfig 2013-11-22 18:20:10.323965853 +0100
+++ b/arch/powerpc/configs.new/mpc866_ads_defconfig 2013-11-22 18:17:32.480904735 +0100
@@ -55,3 +55,4 @@
CONFIG_CRC_CCITT=y
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRC32_SLICEBY4=y
diff -ur a/arch/powerpc/configs/mpc885_ads_defconfig b/arch/powerpc/configs.new/mpc885_ads_defconfig
--- a/arch/powerpc/configs/mpc885_ads_defconfig 2013-11-22 18:20:10.326966235 +0100
+++ b/arch/powerpc/configs.new/mpc885_ads_defconfig 2013-11-22 18:17:25.760050546 +0100
@@ -78,3 +78,4 @@
CONFIG_DETECT_HUNG_TASK=y
CONFIG_DEBUG_INFO=y
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+CONFIG_CRC32_SLICEBY4=y
diff -ur a/arch/powerpc/configs/tqm8xx_defconfig b/arch/powerpc/configs.new/tqm8xx_defconfig
--- a/arch/powerpc/configs/tqm8xx_defconfig 2013-11-22 18:20:10.317965090 +0100
+++ b/arch/powerpc/configs.new/tqm8xx_defconfig 2013-11-22 18:17:14.926673681 +0100
@@ -84,3 +84,4 @@
CONFIG_DETECT_HUNG_TASK=y
CONFIG_DEBUG_INFO=y
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+CONFIG_CRC32_SLICEBY4=y
^ permalink raw reply
* Re: [PATCH v2] powerpc/gpio: Fix the wrong GPIO input data on MPC8572/MPC8536
From: Scott Wood @ 2013-11-22 18:39 UTC (permalink / raw)
To: Liu Gang; +Cc: b07421, linus.walleij, r61911, linux-gpio, agust, linuxppc-dev
In-Reply-To: <1385107960-373-1-git-send-email-Gang.Liu@freescale.com>
On Fri, 2013-11-22 at 16:12 +0800, Liu Gang wrote:
> For MPC8572/MPC8536, the status of GPIOs defined as output
> cannot be determined by reading GPDAT register, so the code
> use shadow data register instead. But the code may give the
> wrong status of GPIOs defined as input under some scenarios:
>
> 1. If some pins were configured as inputs and were asserted
> high before booting the kernel, the shadow data has been
> initialized with those pin values.
> 2. Some pins have been configured as output first and have
> been set to the high value, then reconfigured as input.
>
> The above cases will make the shadow data for those input
> pins to be set to high. Then reading the pin status will
> always return high even if the actual pin status is low.
>
> The code should eliminate the effects of the shadow data to
> the input pins, and the status of those pins should be
> read directly from GPDAT.
>
> Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
> ---
> changes in v2:
> - Added more description of the problem.
> - Reduced one in_be32() call.
> - Do not modify the shadow data.
>
> drivers/gpio/gpio-mpc8xxx.c | 8 ++++++--
> 1 file changed, 6 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/gpio/gpio-mpc8xxx.c b/drivers/gpio/gpio-mpc8xxx.c
> index 914e859..d7d6d72 100644
> --- a/drivers/gpio/gpio-mpc8xxx.c
> +++ b/drivers/gpio/gpio-mpc8xxx.c
> @@ -70,10 +70,14 @@ static int mpc8572_gpio_get(struct gpio_chip *gc, unsigned int gpio)
> u32 val;
> struct of_mm_gpio_chip *mm = to_of_mm_gpio_chip(gc);
> struct mpc8xxx_gpio_chip *mpc8xxx_gc = to_mpc8xxx_gpio_chip(mm);
> + u32 out_mask, out_shadow;
>
> - val = in_be32(mm->regs + GPIO_DAT) & ~in_be32(mm->regs + GPIO_DIR);
> + out_mask = in_be32(mm->regs + GPIO_DIR);
>
> - return (val | mpc8xxx_gc->data) & mpc8xxx_gpio2mask(gpio);
> + val = in_be32(mm->regs + GPIO_DAT) & ~out_mask;
> + out_shadow = mpc8xxx_gc->data & out_mask;
> +
> + return (val | out_shadow) & mpc8xxx_gpio2mask(gpio);
> }
>
> static int mpc8xxx_gpio_get(struct gpio_chip *gc, unsigned int gpio)
Acked-by: Scott Wood <scottwood@freescale.com>
-Scott
^ permalink raw reply
* Re: [PATCH v2] powerpc/gpio: Fix the wrong GPIO input data on MPC8572/MPC8536
From: Kumar Gala @ 2013-11-22 20:51 UTC (permalink / raw)
To: Liu Gang; +Cc: b07421, linus.walleij, r61911, linux-gpio, agust, linuxppc-dev
In-Reply-To: <1385107960-373-1-git-send-email-Gang.Liu@freescale.com>
On Nov 22, 2013, at 2:12 AM, Liu Gang <Gang.Liu@freescale.com> wrote:
> For MPC8572/MPC8536, the status of GPIOs defined as output
> cannot be determined by reading GPDAT register, so the code
> use shadow data register instead. But the code may give the
> wrong status of GPIOs defined as input under some scenarios:
>=20
> 1. If some pins were configured as inputs and were asserted
> high before booting the kernel, the shadow data has been
> initialized with those pin values.
> 2. Some pins have been configured as output first and have
> been set to the high value, then reconfigured as input.
>=20
> The above cases will make the shadow data for those input
> pins to be set to high. Then reading the pin status will
> always return high even if the actual pin status is low.
>=20
> The code should eliminate the effects of the shadow data to
> the input pins, and the status of those pins should be
> read directly from GPDAT.
>=20
> Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
> ---
> changes in v2:
> - Added more description of the problem.
> - Reduced one in_be32() call.
> - Do not modify the shadow data.
>=20
> drivers/gpio/gpio-mpc8xxx.c | 8 ++++++--
> 1 file changed, 6 insertions(+), 2 deletions(-)
>=20
> diff --git a/drivers/gpio/gpio-mpc8xxx.c b/drivers/gpio/gpio-mpc8xxx.c
> index 914e859..d7d6d72 100644
> --- a/drivers/gpio/gpio-mpc8xxx.c
> +++ b/drivers/gpio/gpio-mpc8xxx.c
> @@ -70,10 +70,14 @@ static int mpc8572_gpio_get(struct gpio_chip *gc, =
unsigned int gpio)
> u32 val;
> struct of_mm_gpio_chip *mm =3D to_of_mm_gpio_chip(gc);
> struct mpc8xxx_gpio_chip *mpc8xxx_gc =3D =
to_mpc8xxx_gpio_chip(mm);
> + u32 out_mask, out_shadow;
>=20
> - val =3D in_be32(mm->regs + GPIO_DAT) & ~in_be32(mm->regs + =
GPIO_DIR);
> + out_mask =3D in_be32(mm->regs + GPIO_DIR);
>=20
> - return (val | mpc8xxx_gc->data) & mpc8xxx_gpio2mask(gpio);
> + val =3D in_be32(mm->regs + GPIO_DAT) & ~out_mask;
> + out_shadow =3D mpc8xxx_gc->data & out_mask;
> +
> + return (val | out_shadow) & mpc8xxx_gpio2mask(gpio);
> }
I really think a comment is worth adding here about why we do this.
- k
>=20
> static int mpc8xxx_gpio_get(struct gpio_chip *gc, unsigned int gpio)
> --=20
> 1.8.4.1
>=20
>=20
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@lists.ozlabs.org
> https://lists.ozlabs.org/listinfo/linuxppc-dev
^ permalink raw reply
* Windfarm's max6690 sensor driver was not included in makefile
From: Stanislav Ponomarev @ 2013-11-22 21:09 UTC (permalink / raw)
To: linuxppc-dev
[-- Attachment #1.1: Type: text/plain, Size: 1042 bytes --]
Hello, I had problems with fan speed in my XServe G5. It turned out
drivers/macintosh/Makefile has a max6690 module missing from compilation
list. I was advised to mail the patch to you guys.
I'm not sure what's the proper format of the patch to be submitten (this is
my first time). So I'm including it into the message body, and as an
attached file.
diff --git a/drivers/macintosh/Makefile b/drivers/macintosh/Makefile
index 6753b65..d2f0120 100644
--- a/drivers/macintosh/Makefile
+++ b/drivers/macintosh/Makefile
@@ -40,6 +40,7 @@ obj-$(CONFIG_WINDFARM_RM31) +=
windfarm_fcu_controls.o \
windfarm_ad7417_sensor.o \
windfarm_lm75_sensor.o \
windfarm_lm87_sensor.o \
+ windfarm_max6690_sensor.o \
windfarm_pid.o \
windfarm_cpufreq_clamp.o \
windfarm_rm31.o
Thank you.
Stanislav Ponomarev.
[-- Attachment #1.2: Type: text/html, Size: 1189 bytes --]
[-- Attachment #2: Makefile.patch --]
[-- Type: text/x-patch, Size: 585 bytes --]
index 6753b65..d2f0120 100644
--- a/drivers/macintosh/Makefile
+++ b/drivers/macintosh/Makefile
@@ -40,6 +40,7 @@ obj-$(CONFIG_WINDFARM_RM31) += windfarm_fcu_controls.o \
windfarm_ad7417_sensor.o \
windfarm_lm75_sensor.o \
windfarm_lm87_sensor.o \
+ windfarm_max6690_sensor.o \
windfarm_pid.o \
windfarm_cpufreq_clamp.o \
windfarm_rm31.o
^ permalink raw reply related
* Re: [PATCH 1/8] IBM Akebono: Add support to AHCI platform driver
From: Tejun Heo @ 2013-11-22 22:24 UTC (permalink / raw)
To: Alistair Popple; +Cc: linux-ide, linuxppc-dev
In-Reply-To: <1385086116-10972-1-git-send-email-alistair@popple.id.au>
Hello,
On Thu, Nov 21, 2013 at 9:08 PM, Alistair Popple <alistair@popple.id.au> wrote:
> The new IBM Akebono board has a PPC476GTR SoC with an AHCI compliant
> SATA controller. This patch adds a compatible property for the new SoC
> to the AHCI platform driver.
>
> Signed-off-by: Alistair Popple <alistair@popple.id.au>
Applied to libata/for-3.13-fixes w/ stable cc'd.
Thanks.
--
tejun
^ permalink raw reply
* Re: [PATCH 1/6] powerpc: fix exception clearing in e500 SPE float emulation
From: Scott Wood @ 2013-11-22 22:34 UTC (permalink / raw)
To: Joseph S. Myers; +Cc: Liu Yu, linuxppc-dev, linux-kernel, Shan Hai
In-Reply-To: <Pine.LNX.4.64.1311041651390.4290@digraph.polyomino.org.uk>
On Mon, 2013-11-04 at 16:52 +0000, Joseph S. Myers wrote:
> From: Joseph Myers <joseph@codesourcery.com>
>
> The e500 SPE floating-point emulation code clears existing exceptions
> (__FPU_FPSCR &= ~FP_EX_MASK;) before ORing in the exceptions from the
> emulated operation. However, these exception bits are the "sticky",
> cumulative exception bits, and should only be cleared by the user
> program setting SPEFSCR, not implicitly by any floating-point
> instruction (whether executed purely by the hardware or emulated).
> The spurious clearing of these bits shows up as missing exceptions in
> glibc testing.
>
> Fixing this, however, is not as simple as just not clearing the bits,
> because while the bits may be from previous floating-point operations
> (in which case they should not be cleared), the processor can also set
> the sticky bits itself before the interrupt for an exception occurs,
> and this can happen in cases when IEEE 754 semantics are that the
> sticky bit should not be set. Specifically, the "invalid" sticky bit
> is set in various cases with non-finite operands, where IEEE 754
> semantics do not involve raising such an exception, and the
> "underflow" sticky bit is set in cases of exact underflow, whereas
> IEEE 754 semantics are that this flag is set only for inexact
> underflow. Thus, for correct emulation the kernel needs to know the
> setting of these two sticky bits before the instruction being
> emulated.
>
> When a floating-point operation raises an exception, the kernel can
> note the state of the sticky bits immediately afterwards. Some
> <fenv.h> functions that affect the state of these bits, such as
> fesetenv and feholdexcept, need to use prctl with PR_GET_FPEXC and
> PR_SET_FPEXC anyway, and so it is natural to record the state of those
> bits during that call into the kernel and so avoid any need for a
> separate call into the kernel to inform it of a change to those bits.
> Thus, the interface I chose to use (in this patch and the glibc port)
> is that one of those prctl calls must be made after any userspace
> change to those sticky bits, other than through a floating-point
> operation that traps into the kernel anyway.
This sounds like an incompatible change to userspace API. What about
older glibc? What about user code that directly manipulates these bits
rather than going through libc, or uses a libc other than glibc? Where
is this API requirement documented?
I think the impact of this could be reduced by using this mechanism only
to clear bits, rather than set them. That is, if the exception bit is
unset, don't set it just because it's set in spefscr_last -- but if it's
not set in spefscr_last, and the emulation code doesn't want to set it,
then clear it.
Are there any cases where the exception bit can be set without the
kernel taking a trap, or is userspace manipulation limited to clearing
the bits?
-Scott
^ permalink raw reply
* Pull request: scottwood/linux.git
From: Scott Wood @ 2013-11-22 23:21 UTC (permalink / raw)
To: benh; +Cc: linuxppc-dev
The corenet64 patch fixes a regression introduced in 3.13-rc1 (commit
ef1313deafb7baa6d3382044e962d5ad5e8c8dd6, "powerpc: Add VMX optimised xor
for RAID5").
The 8xx patch fixes a regression introduced in 3.12 (commit
beb2dc0a7a84be003ce54e98b95d65cc66e6e536, "powerpc: Convert some
mftb/mftbu into mfspr").
The other two patches are fixes for minor, long standing bugs.
The following changes since commit 6ce4eac1f600b34f2f7f58f9cd8f0503d79e42ae:
Linux 3.13-rc1 (2013-11-22 11:30:55 -0800)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/scottwood/linux.git
for you to fetch changes up to d742aa152f27448d39ce65fb829e396d10cd63a9:
powerpc/booke: Only check for hugetlb in flush if vma != NULL (2013-11-22 16:57:29 -0600)
----------------------------------------------------------------
Adam Borowski (1):
powerpc/85xx: typo in dts: "interupt" (four devices)
LEROY Christophe (1):
powerpc/8xx: mfspr SPRN_TBRx in lieu of mftb/mftbu is not supported
Scott Wood (1):
powerpc/booke: Only check for hugetlb in flush if vma != NULL
Tiejun Chen (1):
powerpc/corenet64: compile with CONFIG_E{5,6}500_CPU well
arch/powerpc/Makefile | 5 +++++
arch/powerpc/boot/dts/xcalibur1501.dts | 4 ++--
arch/powerpc/boot/dts/xpedite5301.dts | 4 ++--
arch/powerpc/boot/dts/xpedite5330.dts | 4 ++--
arch/powerpc/boot/dts/xpedite5370.dts | 4 ++--
arch/powerpc/boot/util.S | 14 ++++++++++++++
arch/powerpc/include/asm/ppc_asm.h | 2 ++
arch/powerpc/include/asm/reg.h | 7 +++++++
arch/powerpc/include/asm/timex.h | 8 ++++++++
arch/powerpc/kernel/vdso32/gettimeofday.S | 6 ++++++
arch/powerpc/mm/hugetlbpage-book3e.c | 3 +--
arch/powerpc/mm/tlb_nohash.c | 2 +-
12 files changed, 52 insertions(+), 11 deletions(-)
^ permalink raw reply
* eth0: hw csum failure
From: Andreas Schwab @ 2013-11-23 0:44 UTC (permalink / raw)
To: linuxppc-dev
I get a lot of "eth0: hw csum failure" with 3.13-rc1 on my G5.
eth0: hw csum failure
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.13.0-rc1 #1
Call Trace:
[c00000000ffef1d0] [c00000000000f97c] .show_stack+0x60/0x14c (unreliable)
[c00000000ffef2a0] [c00000000069fad8] .dump_stack+0x80/0xa0
[c00000000ffef320] [c000000000552bc0] .netdev_rx_csum_fault+0x4c/0x58
[c00000000ffef3a0] [c000000000546f88] .__skb_checksum_complete_head+0x54/0x78
[c00000000ffef420] [c0000000005f1118] .nf_ip_checksum+0xf4/0x100
[c00000000ffef4b0] [c00000000058e520] .udp_error+0x198/0x210
[c00000000ffef560] [c000000000587694] .nf_conntrack_in+0x14c/0xa20
[c00000000ffef690] [c0000000005f195c] .ipv4_conntrack_in+0x24/0x38
[c00000000ffef700] [c00000000058343c] .nf_iterate+0x64/0xb4
[c00000000ffef7c0] [c00000000058353c] .nf_hook_slow+0xb0/0x188
[c00000000ffef890] [c00000000059ea9c] .ip_rcv+0x390/0x3f0
[c00000000ffef930] [c000000000551578] .__netif_receive_skb_core+0x8c4/0x964
[c00000000ffefa30] [c000000000551c38] .netif_receive_skb+0xb0/0x130
[c00000000ffefae0] [c000000000552740] .napi_gro_receive+0x50/0xc0
[c00000000ffefb60] [c000000000447754] .gem_poll+0x10f0/0x1328
[c00000000ffefcc0] [c000000000552418] .net_rx_action+0xd8/0x240
[c00000000ffefd90] [c00000000004dfc4] .__do_softirq+0x158/0x2c0
[c00000000ffefea0] [c00000000004e448] .irq_exit+0x6c/0xc4
[c00000000ffeff10] [c00000000000ce14] .__do_irq+0xec/0xf8
[c00000000ffeff90] [c000000000019474] .call_do_irq+0x14/0x24
[c0000001f615ba30] [c00000000000cea0] .do_IRQ+0x80/0xc0
[c0000001f615bac0] [c0000000000024b8] hardware_interrupt_common+0x138/0x180
--- Exception: 501 at .arch_cpu_idle+0x78/0x124
LR = .arch_cpu_idle+0x78/0x124
[c0000001f615bdb0] [c0000000000a3af4] .rcu_idle_enter+0x98/0xb8 (unreliable)
[c0000001f615be30] [c00000000009a978] .cpu_startup_entry+0x110/0x1a0
[c0000001f615bee0] [c00000000001f14c] .start_secondary+0x288/0x290
[c0000001f615bf90] [c0000000000087fc] .start_secondary_prolog+0x10/0x14
Andreas.
--
Andreas Schwab, schwab@linux-m68k.org
GPG Key fingerprint = 58CA 54C7 6D53 942B 1756 01D3 44D5 214B 8276 4ED5
"And now for something completely different."
^ permalink raw reply
* Re: [PATCH 1/6] powerpc: fix exception clearing in e500 SPE float emulation
From: Joseph S. Myers @ 2013-11-23 1:22 UTC (permalink / raw)
To: Scott Wood; +Cc: Liu Yu, linuxppc-dev, linux-kernel, Shan Hai
In-Reply-To: <1385159644.1403.532.camel@snotra.buserror.net>
On Fri, 22 Nov 2013, Scott Wood wrote:
> This sounds like an incompatible change to userspace API. What about
> older glibc? What about user code that directly manipulates these bits
> rather than going through libc, or uses a libc other than glibc? Where
> is this API requirement documented?
The previous EGLIBC port, and the uClibc code copied from it, is
fundamentally broken as regards any use of prctl for floating-point
exceptions because it didn't use the PR_FP_EXC_SW_ENABLE bit in its prctl
calls (and did various worse things, such as passing a pointer when prctl
expected an integer). If you avoid anything where prctl is used, the
clearing of sticky bits still means it will never give anything
approximating correct exception semantics with existing kernels. I don't
believe the patch makes things any worse for existing code that doesn't
try to inform the kernel of changes to sticky bits - such code may get
incorrect exceptions in some cases, but it would have done so anyway in
other cases.
This is the best API I could come up with to fix the fundamentally broken
nature of what came before, taking into account that in many cases a prctl
call is already needed along with userspace manipulation of exception
bits. I'm not aware of any kernel documentation where this sort of
subarchitecture-specific API detail is documented. (The API also includes
such things as needing to leave the spefscr trap-enable bits set and use
prctl to control whether SIGFPE results from exceptions.)
> I think the impact of this could be reduced by using this mechanism only
> to clear bits, rather than set them. That is, if the exception bit is
> unset, don't set it just because it's set in spefscr_last -- but if it's
> not set in spefscr_last, and the emulation code doesn't want to set it,
> then clear it.
It should already be the case in this patch that if a bit is clear in
spefscr, and set in spefscr_last (i.e. userspace did not inform the kernel
of clearing the bit, and no traps since then have resulted in the kernel
noticing it was cleared), it won't get set unless the emulation code wants
to set it. The sole place spefscr_last is read is in the statement
"__FPU_FPSCR &= ~(FP_EX_INVALID | FP_EX_UNDERFLOW) |
current->thread.spefscr_last;" - if the bit is already clear in spefscr,
this statement has no effect on it.
> Are there any cases where the exception bit can be set without the
> kernel taking a trap, or is userspace manipulation limited to clearing
> the bits?
Userspace can both set and clear the bits without a trap. For example,
fesetenv restores a saved value of spefscr which may both set and clear
bits (and then it calls prctl because it needs to do so anyway to restore
the saved state for which exceptions were enabled). fesetexceptflag
restores saved state of particular exceptions without a trap (so needs to
call prctl specially to inform the kernel of a change).
--
Joseph S. Myers
joseph@codesourcery.com
^ permalink raw reply
* [RFC,PATCH] powerpc/powernv: Add iommu DMA bypass support for IODA2
From: Benjamin Herrenschmidt @ 2013-11-23 8:36 UTC (permalink / raw)
To: linuxppc-dev list; +Cc: Anton Blanchard
This patch adds the support for to create a direct iommu "bypass"
window on IODA2 bridges (such as Power8) allowing to bypass iommu
page translation completely for 64-bit DMA capable devices.
This is currently enabled unconditionally for any 64-bit device,
we *may* want to make it conditional to a command line argument.
Additionally, this adds a hook to the struct iommu_table so that
the IOMMU API / VFIO can disable the bypass when external ownership
is requested, since in that case, the device will be used by an
environment such as userspace or a KVM guest which must not be
allowed to bypass translations.
It should be possible to do something similar for IODA1 (Power7)
though not all versions of OPALv2/v3 out there support that properly
so for now I won't bother.
Not-yet-signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
diff --git a/arch/powerpc/include/asm/dma-mapping.h b/arch/powerpc/include/asm/dma-mapping.h
index e27e9ad..150866b 100644
--- a/arch/powerpc/include/asm/dma-mapping.h
+++ b/arch/powerpc/include/asm/dma-mapping.h
@@ -134,6 +134,7 @@ static inline int dma_supported(struct device *dev, u64 mask)
}
extern int dma_set_mask(struct device *dev, u64 dma_mask);
+extern int __dma_set_mask(struct device *dev, u64 dma_mask);
#define dma_alloc_coherent(d,s,h,f) dma_alloc_attrs(d,s,h,f,NULL)
diff --git a/arch/powerpc/include/asm/iommu.h b/arch/powerpc/include/asm/iommu.h
index c34656a..ed2e582 100644
--- a/arch/powerpc/include/asm/iommu.h
+++ b/arch/powerpc/include/asm/iommu.h
@@ -79,6 +79,7 @@ struct iommu_table {
#ifdef CONFIG_IOMMU_API
struct iommu_group *it_group;
#endif
+ void (*set_bypass)(struct iommu_table *tbl, bool enable);
};
struct scatterlist;
diff --git a/arch/powerpc/kernel/dma.c b/arch/powerpc/kernel/dma.c
index 8032b97..ee78f6e 100644
--- a/arch/powerpc/kernel/dma.c
+++ b/arch/powerpc/kernel/dma.c
@@ -191,12 +191,10 @@ EXPORT_SYMBOL(dma_direct_ops);
#define PREALLOC_DMA_DEBUG_ENTRIES (1 << 16)
-int dma_set_mask(struct device *dev, u64 dma_mask)
+int __dma_set_mask(struct device *dev, u64 dma_mask)
{
struct dma_map_ops *dma_ops = get_dma_ops(dev);
- if (ppc_md.dma_set_mask)
- return ppc_md.dma_set_mask(dev, dma_mask);
if ((dma_ops != NULL) && (dma_ops->set_dma_mask != NULL))
return dma_ops->set_dma_mask(dev, dma_mask);
if (!dev->dma_mask || !dma_supported(dev, dma_mask))
@@ -204,6 +202,12 @@ int dma_set_mask(struct device *dev, u64 dma_mask)
*dev->dma_mask = dma_mask;
return 0;
}
+int dma_set_mask(struct device *dev, u64 dma_mask)
+{
+ if (ppc_md.dma_set_mask)
+ return ppc_md.dma_set_mask(dev, dma_mask);
+ return __dma_set_mask(dev, dma_mask);
+}
EXPORT_SYMBOL(dma_set_mask);
u64 dma_get_required_mask(struct device *dev)
diff --git a/arch/powerpc/platforms/powernv/pci-ioda.c b/arch/powerpc/platforms/powernv/pci-ioda.c
index 084cdfa..0425a2e 100644
--- a/arch/powerpc/platforms/powernv/pci-ioda.c
+++ b/arch/powerpc/platforms/powernv/pci-ioda.c
@@ -21,6 +21,7 @@
#include <linux/irq.h>
#include <linux/io.h>
#include <linux/msi.h>
+#include <linux/memblock.h>
#include <asm/sections.h>
#include <asm/io.h>
@@ -460,7 +461,38 @@ static void pnv_pci_ioda_dma_dev_setup(struct pnv_phb *phb, struct pci_dev *pdev
return;
pe = &phb->ioda.pe_array[pdn->pe_number];
- set_iommu_table_base(&pdev->dev, &pe->tce32_table);
+ if (get_dma_ops(&pdev->dev) == &dma_direct_ops)
+ set_dma_offset(&pdev->dev, pe->tce_bypass_base);
+ else
+ set_iommu_table_base(&pdev->dev, &pe->tce32_table);
+}
+
+static int pnv_pci_ioda_dma_set_mask(struct pnv_phb *phb,
+ struct pci_dev *pdev, u64 dma_mask)
+{
+ struct pci_dn *pdn = pci_get_pdn(pdev);
+ struct pnv_ioda_pe *pe;
+ uint64_t top;
+ bool bypass = false;
+
+ if (!WARN_ON(!pdn || pdn->pe_number == IODA_INVALID_PE)) {
+ pe = &phb->ioda.pe_array[pdn->pe_number];
+ if (pe->tce_bypass_enabled) {
+ top = pe->tce_bypass_base + memblock_end_of_DRAM() - 1;
+ bypass = (dma_mask >= top);
+ }
+ }
+
+ if (bypass) {
+ dev_info(&pdev->dev, "Using 64-bit DMA iommu bypass\n");
+ set_dma_ops(&pdev->dev, &dma_direct_ops);
+ } else {
+ dev_info(&pdev->dev, "Using 32-bit DMA via iommu\n");
+ set_dma_ops(&pdev->dev, &dma_iommu_ops);
+ }
+ pnv_pci_ioda_dma_dev_setup(phb, pdev);
+
+ return 0;
}
static void pnv_ioda_setup_bus_dma(struct pnv_ioda_pe *pe, struct pci_bus *bus)
@@ -657,6 +689,56 @@ static void pnv_pci_ioda_setup_dma_pe(struct pnv_phb *phb,
__free_pages(tce_mem, get_order(TCE32_TABLE_SIZE * segs));
}
+static void pnv_pci_ioda2_set_bypass(struct iommu_table *tbl, bool enable)
+{
+ struct pnv_ioda_pe *pe = container_of(tbl, struct pnv_ioda_pe,
+ tce32_table);
+ uint16_t window_id = (pe->pe_number << 1 ) + 1;
+ int64_t rc;
+
+ pe_info(pe, "%sabling 64-bit DMA bypass\n", enable ? "En" : "Dis");
+ if (enable) {
+ phys_addr_t top = memblock_end_of_DRAM();
+
+ top = roundup_pow_of_two(top);
+ rc = opal_pci_map_pe_dma_window_real(pe->phb->opal_id,
+ pe->pe_number,
+ window_id,
+ pe->tce_bypass_base,
+ top);
+ } else {
+ rc = opal_pci_map_pe_dma_window_real(pe->phb->opal_id,
+ pe->pe_number,
+ window_id,
+ pe->tce_bypass_base,
+ 0);
+
+ /*
+ * We might want to reset the DMA ops of all devices on
+ * this PE. However in theory, that shouldn't be necessary
+ * as this is used for VFIO/KVM pass-through and the device
+ * hasn't yet been returned to its kernel driver
+ */
+ }
+ if (rc)
+ pe_err(pe, "OPAL error %lld configuring bypass window\n", rc);
+ else
+ pe->tce_bypass_enabled = enable;
+}
+
+static void pnv_pci_ioda2_setup_bypass_pe(struct pnv_phb *phb,
+ struct pnv_ioda_pe *pe)
+{
+ /* TVE #1 is selected by PCI address bit 59 */
+ pe->tce_bypass_base = 1ull << 59;
+
+ /* Install set_bypass callback for VFIO */
+ pe->tce32_table.set_bypass = pnv_pci_ioda2_set_bypass;
+
+ /* Enable bypass by default */
+ pnv_pci_ioda2_set_bypass(&pe->tce32_table, true);
+}
+
static void pnv_pci_ioda2_setup_dma_pe(struct pnv_phb *phb,
struct pnv_ioda_pe *pe)
{
@@ -726,6 +808,8 @@ static void pnv_pci_ioda2_setup_dma_pe(struct pnv_phb *phb,
else
pnv_ioda_setup_bus_dma(pe, pe->pbus);
+ /* Also create a bypass window */
+ pnv_pci_ioda2_setup_bypass_pe(phb, pe);
return;
fail:
if (pe->tce32_seg >= 0)
@@ -1286,6 +1370,7 @@ void __init pnv_pci_init_ioda_phb(struct device_node *np,
/* Setup TCEs */
phb->dma_dev_setup = pnv_pci_ioda_dma_dev_setup;
+ phb->dma_set_mask = pnv_pci_ioda_dma_set_mask;
/* Setup shutdown function for kexec */
phb->shutdown = pnv_pci_ioda_shutdown;
diff --git a/arch/powerpc/platforms/powernv/pci.c b/arch/powerpc/platforms/powernv/pci.c
index 4eb33a9..e96af77 100644
--- a/arch/powerpc/platforms/powernv/pci.c
+++ b/arch/powerpc/platforms/powernv/pci.c
@@ -553,6 +553,16 @@ static void pnv_pci_dma_dev_setup(struct pci_dev *pdev)
pnv_pci_dma_fallback_setup(hose, pdev);
}
+int pnv_pci_dma_set_mask(struct pci_dev *pdev, u64 dma_mask)
+{
+ struct pci_controller *hose = pci_bus_to_host(pdev->bus);
+ struct pnv_phb *phb = hose->private_data;
+
+ if (phb && phb->dma_set_mask)
+ return phb->dma_set_mask(phb, pdev, dma_mask);
+ return __dma_set_mask(&pdev->dev, dma_mask);
+}
+
void pnv_pci_shutdown(void)
{
struct pci_controller *hose;
diff --git a/arch/powerpc/platforms/powernv/pci.h b/arch/powerpc/platforms/powernv/pci.h
index 911c24e..62ac4ef 100644
--- a/arch/powerpc/platforms/powernv/pci.h
+++ b/arch/powerpc/platforms/powernv/pci.h
@@ -54,7 +54,9 @@ struct pnv_ioda_pe {
struct iommu_table tce32_table;
phys_addr_t tce_inval_reg_phys;
- /* XXX TODO: Add support for additional 64-bit iommus */
+ /* 64-bit TCE bypass region */
+ bool tce_bypass_enabled;
+ uint64_t tce_bypass_base;
/* MSIs. MVE index is identical for for 32 and 64 bit MSI
* and -1 if not supported. (It's actually identical to the
@@ -113,6 +115,8 @@ struct pnv_phb {
unsigned int hwirq, unsigned int virq,
unsigned int is_64, struct msi_msg *msg);
void (*dma_dev_setup)(struct pnv_phb *phb, struct pci_dev *pdev);
+ int (*dma_set_mask)(struct pnv_phb *phb, struct pci_dev *pdev,
+ u64 dma_mask);
void (*fixup_phb)(struct pci_controller *hose);
u32 (*bdfn_to_pe)(struct pnv_phb *phb, struct pci_bus *bus, u32 devfn);
void (*shutdown)(struct pnv_phb *phb);
diff --git a/arch/powerpc/platforms/powernv/powernv.h b/arch/powerpc/platforms/powernv/powernv.h
index de6819b..213887a 100644
--- a/arch/powerpc/platforms/powernv/powernv.h
+++ b/arch/powerpc/platforms/powernv/powernv.h
@@ -7,12 +7,16 @@ extern void pnv_smp_init(void);
static inline void pnv_smp_init(void) { }
#endif
+struct pci_dev;
+
#ifdef CONFIG_PCI
extern void pnv_pci_init(void);
extern void pnv_pci_shutdown(void);
+extern int pnv_pci_dma_set_mask(struct pci_dev *pdev, u64 dma_mask);
#else
static inline void pnv_pci_init(void) { }
static inline void pnv_pci_shutdown(void) { }
+static inline int pnv_pci_dma_set_mask(struct pci_dev *pdev, u64 dma_mask) { }
#endif
extern void pnv_lpc_init(void);
diff --git a/arch/powerpc/platforms/powernv/setup.c b/arch/powerpc/platforms/powernv/setup.c
index 19884b2..f519f55 100644
--- a/arch/powerpc/platforms/powernv/setup.c
+++ b/arch/powerpc/platforms/powernv/setup.c
@@ -26,6 +26,7 @@
#include <linux/of_fdt.h>
#include <linux/interrupt.h>
#include <linux/bug.h>
+#include <linux/pci.h>
#include <asm/machdep.h>
#include <asm/firmware.h>
@@ -140,6 +141,13 @@ static void pnv_progress(char *s, unsigned short hex)
{
}
+static int pnv_dma_set_mask(struct device *dev, u64 dma_mask)
+{
+ if (dev_is_pci(dev))
+ return pnv_pci_dma_set_mask(to_pci_dev(dev), dma_mask);
+ return __dma_set_mask(dev, dma_mask);
+}
+
static void pnv_shutdown(void)
{
/* Let the PCI code clear up IODA tables */
@@ -223,6 +231,7 @@ define_machine(powernv) {
.show_cpuinfo = pnv_show_cpuinfo,
.progress = pnv_progress,
.machine_shutdown = pnv_shutdown,
+ .dma_set_mask = pnv_dma_set_mask,
.power_save = power7_idle,
.calibrate_decr = generic_calibrate_decr,
#ifdef CONFIG_KEXEC
^ permalink raw reply related
* Re: [PATCH v2] offb: make the screen properties endian safe
From: Cedric Le Goater @ 2013-11-23 17:38 UTC (permalink / raw)
To: Benjamin Herrenschmidt; +Cc: linuxppc-dev
In-Reply-To: <1385063848.4882.6.camel@pasglop>
On 11/21/2013 08:57 PM, Benjamin Herrenschmidt wrote:
> On Thu, 2013-11-21 at 16:45 +0100, Cedric Le Goater wrote:
>>> - fbdev *generally* assume native endian framebuffer, but of course
>>> under qemu today, the adapter will use a big endian frame buffer
>>> aperture. You can compile in support for foreign endian but I don't know
>>> how that actually works.
>>
>> OK. I will see how I can extend the tests. But, are you suggesting I should
>> be using the foreign endian framework for the frame buffer ?
>
> Well, if it works ... did you try 16 and 32bpp ?
So, 32bpp "works" but 16 is broken ... I guess my palette fix is just a lucky
hack and I need to dig deeper in fb code to have a better understanding of
the color map.
I should have provided you two patches in the first place. Do you want the
device tree data fixes for the frame buffer screen properties ? It helps to
have a display for little endian guests even if the colors are wrong.
Thanks,
C.
^ permalink raw reply
* Re: [PATCH v2] offb: make the screen properties endian safe
From: Benjamin Herrenschmidt @ 2013-11-23 21:04 UTC (permalink / raw)
To: Cedric Le Goater; +Cc: linuxppc-dev
In-Reply-To: <5290E820.2080809@fr.ibm.com>
On Sat, 2013-11-23 at 18:38 +0100, Cedric Le Goater wrote:
> So, 32bpp "works" but 16 is broken ... I guess my palette fix is just a lucky
> hack and I need to dig deeper in fb code to have a better understanding of
> the color map.
>
> I should have provided you two patches in the first place. Do you want the
> device tree data fixes for the frame buffer screen properties ? It helps to
> have a display for little endian guests even if the colors are wrong.
Before you pull your hair out, check if it works in BE :-)
Cheers,
Ben.
^ permalink raw reply
* Re: eth0: hw csum failure
From: Benjamin Herrenschmidt @ 2013-11-23 21:17 UTC (permalink / raw)
To: Andreas Schwab; +Cc: linuxppc-dev
In-Reply-To: <87d2ls54mn.fsf@igel.home>
On Sat, 2013-11-23 at 01:44 +0100, Andreas Schwab wrote:
> I get a lot of "eth0: hw csum failure" with 3.13-rc1 on my G5.
Alex Graf already reported that, we're looking into it.
Cheers,
Ben.
> eth0: hw csum failure
> CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.13.0-rc1 #1
> Call Trace:
> [c00000000ffef1d0] [c00000000000f97c] .show_stack+0x60/0x14c (unreliable)
> [c00000000ffef2a0] [c00000000069fad8] .dump_stack+0x80/0xa0
> [c00000000ffef320] [c000000000552bc0] .netdev_rx_csum_fault+0x4c/0x58
> [c00000000ffef3a0] [c000000000546f88] .__skb_checksum_complete_head+0x54/0x78
> [c00000000ffef420] [c0000000005f1118] .nf_ip_checksum+0xf4/0x100
> [c00000000ffef4b0] [c00000000058e520] .udp_error+0x198/0x210
> [c00000000ffef560] [c000000000587694] .nf_conntrack_in+0x14c/0xa20
> [c00000000ffef690] [c0000000005f195c] .ipv4_conntrack_in+0x24/0x38
> [c00000000ffef700] [c00000000058343c] .nf_iterate+0x64/0xb4
> [c00000000ffef7c0] [c00000000058353c] .nf_hook_slow+0xb0/0x188
> [c00000000ffef890] [c00000000059ea9c] .ip_rcv+0x390/0x3f0
> [c00000000ffef930] [c000000000551578] .__netif_receive_skb_core+0x8c4/0x964
> [c00000000ffefa30] [c000000000551c38] .netif_receive_skb+0xb0/0x130
> [c00000000ffefae0] [c000000000552740] .napi_gro_receive+0x50/0xc0
> [c00000000ffefb60] [c000000000447754] .gem_poll+0x10f0/0x1328
> [c00000000ffefcc0] [c000000000552418] .net_rx_action+0xd8/0x240
> [c00000000ffefd90] [c00000000004dfc4] .__do_softirq+0x158/0x2c0
> [c00000000ffefea0] [c00000000004e448] .irq_exit+0x6c/0xc4
> [c00000000ffeff10] [c00000000000ce14] .__do_irq+0xec/0xf8
> [c00000000ffeff90] [c000000000019474] .call_do_irq+0x14/0x24
> [c0000001f615ba30] [c00000000000cea0] .do_IRQ+0x80/0xc0
> [c0000001f615bac0] [c0000000000024b8] hardware_interrupt_common+0x138/0x180
> --- Exception: 501 at .arch_cpu_idle+0x78/0x124
> LR = .arch_cpu_idle+0x78/0x124
> [c0000001f615bdb0] [c0000000000a3af4] .rcu_idle_enter+0x98/0xb8 (unreliable)
> [c0000001f615be30] [c00000000009a978] .cpu_startup_entry+0x110/0x1a0
> [c0000001f615bee0] [c00000000001f14c] .start_secondary+0x288/0x290
> [c0000001f615bf90] [c0000000000087fc] .start_secondary_prolog+0x10/0x14
>
> Andreas.
>
^ permalink raw reply
* Re: Windfarm's max6690 sensor driver was not included in makefile
From: Benjamin Herrenschmidt @ 2013-11-23 21:18 UTC (permalink / raw)
To: Stanislav Ponomarev; +Cc: linuxppc-dev
In-Reply-To: <CA+2fWjZRw7zdCACXXSTPN4QVeuXN5CLOZSOJJiGuP4UBcS2aMA@mail.gmail.com>
On Fri, 2013-11-22 at 15:09 -0600, Stanislav Ponomarev wrote:
> Hello, I had problems with fan speed in my XServe G5. It turned out
> drivers/macintosh/Makefile has a max6690 module missing from
> compilation list. I was advised to mail the patch to you guys.
>
>
> I'm not sure what's the proper format of the patch to be submitten
> (this is my first time). So I'm including it into the message body,
> and as an attached file.
So make sure you send it as plain text in a form that preserves tabs and
space (I don't now if gmail allows that). Also please include a
"Signed-off-by:" line.
Cheers,
Ben.
> diff --git a/drivers/macintosh/Makefile b/drivers/macintosh/Makefile
> index 6753b65..d2f0120 100644
> --- a/drivers/macintosh/Makefile
> +++ b/drivers/macintosh/Makefile
> @@ -40,6 +40,7 @@ obj-$(CONFIG_WINDFARM_RM31) +=
> windfarm_fcu_controls.o \
> windfarm_ad7417_sensor.o \
> windfarm_lm75_sensor.o \
> windfarm_lm87_sensor.o \
> + windfarm_max6690_sensor.o \
> windfarm_pid.o \
> windfarm_cpufreq_clamp.o \
> windfarm_rm31.o
>
>
>
> Thank you.
>
> Stanislav Ponomarev.
>
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@lists.ozlabs.org
> https://lists.ozlabs.org/listinfo/linuxppc-dev
^ permalink raw reply
* Re: Build regressions/improvements in v3.13-rc1
From: Geert Uytterhoeven @ 2013-11-24 9:17 UTC (permalink / raw)
To: linux-kernel@vger.kernel.org
Cc: sparclinux, linux-xtensa@linux-xtensa.org,
linuxppc-dev@lists.ozlabs.org
In-Reply-To: <1385233105-20026-1-git-send-email-geert@linux-m68k.org>
On Sat, Nov 23, 2013 at 7:58 PM, Geert Uytterhoeven
<geert@linux-m68k.org> wrote:
> 8 regressions:
> + /scratch/kisskb/src/arch/sparc/kernel/kgdb_64.c: error: implicit declaration of function 'exception_enter' [-Werror=implicit-function-declaration]: => 162:7
> + /scratch/kisskb/src/arch/sparc/kernel/kgdb_64.c: error: implicit declaration of function 'exception_exit' [-Werror=implicit-function-declaration]: => 176:2
sparc64-allmodconfig
> + /scratch/kisskb/src/kernel/bounds.c: error: -mcall-aixdesc must be big endian: => 1:0
> + /scratch/kisskb/src/scripts/mod/devicetable-offsets.c: error: -mcall-aixdesc must be big endian: => 1:0
> + /scratch/kisskb/src/scripts/mod/empty.c: error: -mcall-aixdesc must be big endian: => 1:0
> + <stdin>: error: -mcall-aixdesc must be big endian: => 1:0
powerpc-allmodconfig
powerpc-allyesconfig
> + error: drivers/built-in.o: undefined reference to `i2c_register_driver': => .init.literal+0xd88)
> + error: sram.c: undefined reference to `devm_regmap_init_i2c': => .text+0x58ef8)
xtensa-allmodconfig
sparc-allmodconfig
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox