* Hang with Promise Ultra100 TX2 (kernel 2.4.18)
@ 2004-01-15 9:17 Cheng Huang
2004-01-15 11:49 ` Pasi Kärkkäinen
0 siblings, 1 reply; 6+ messages in thread
From: Cheng Huang @ 2004-01-15 9:17 UTC (permalink / raw)
To: linux-kernel; +Cc: cheng
I have to use kernel 2.4.18 because I need to install KURT (realtime
linux) with it. However, my system hangs on boot with the following
message:
PDC20268: not 100% native mode: will probe irqs later
PDC20268: ROM enabled at 0xff900000
ide2: BM-DMA at 0xfcc0-0xfcc7, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xfcc8-0xfccf, BIOS settings: hdg:pio, hdh:pio
I have tried tricks I could find in through google, like setting boot
parameters "hde=4866,255,63 hde=noprobe hdg=24321,255,163 hdg=noprobe".
But it didn't work.
Could anybody provide some clue about how to fix this problem? Thanks
very much.
-- Cheng
^ permalink raw reply [flat|nested] 6+ messages in thread* Re: Hang with Promise Ultra100 TX2 (kernel 2.4.18)
2004-01-15 9:17 Hang with Promise Ultra100 TX2 (kernel 2.4.18) Cheng Huang
@ 2004-01-15 11:49 ` Pasi Kärkkäinen
2004-01-15 15:42 ` Nerijus Baliunas
2004-01-16 21:02 ` Cheng Huang
0 siblings, 2 replies; 6+ messages in thread
From: Pasi Kärkkäinen @ 2004-01-15 11:49 UTC (permalink / raw)
To: Cheng Huang; +Cc: linux-kernel, cheng
On Thu, Jan 15, 2004 at 03:17:12AM -0600, Cheng Huang wrote:
> I have to use kernel 2.4.18 because I need to install KURT (realtime
> linux) with it. However, my system hangs on boot with the following
> message:
>
> PDC20268: not 100% native mode: will probe irqs later
> PDC20268: ROM enabled at 0xff900000
> ide2: BM-DMA at 0xfcc0-0xfcc7, BIOS settings: hde:pio, hdf:pio
> ide3: BM-DMA at 0xfcc8-0xfccf, BIOS settings: hdg:pio, hdh:pio
>
> I have tried tricks I could find in through google, like setting boot
> parameters "hde=4866,255,63 hde=noprobe hdg=24321,255,163 hdg=noprobe".
> But it didn't work.
>
> Could anybody provide some clue about how to fix this problem? Thanks
> very much.
>
I think there has been a lot of bug fixes in the latest 2.4 kernels for
promise cards.
I'm running promise ultra133-tx2 successfully with 2.4.22 kernel.
Merge the promise driver from later 2.4.x kernels to 2.4.18 and recompile?
-- Pasi Kärkkäinen
^
. .
Linux
/ - \
Choice.of.the
.Next.Generation.
^ permalink raw reply [flat|nested] 6+ messages in thread* Re: Hang with Promise Ultra100 TX2 (kernel 2.4.18)
2004-01-15 11:49 ` Pasi Kärkkäinen
@ 2004-01-15 15:42 ` Nerijus Baliunas
2004-01-16 21:02 ` Cheng Huang
1 sibling, 0 replies; 6+ messages in thread
From: Nerijus Baliunas @ 2004-01-15 15:42 UTC (permalink / raw)
To: linux-kernel; +Cc: Cheng Huang
On Thu, 15 Jan 2004 13:49:22 +0200 Pasi Kärkkäinen <pasik@iki.fi> wrote:
> On Thu, Jan 15, 2004 at 03:17:12AM -0600, Cheng Huang wrote:
> > I have to use kernel 2.4.18 because I need to install KURT (realtime
> > linux) with it. However, my system hangs on boot with the following
> > message:
>
> I think there has been a lot of bug fixes in the latest 2.4 kernels for
> promise cards.
>
> I'm running promise ultra133-tx2 successfully with 2.4.22 kernel.
>
> Merge the promise driver from later 2.4.x kernels to 2.4.18 and recompile?
When I used 2.4.18 I had Andre's ide.2.4.18-rc1.02152002.patch.bz2
applied.
Regards,
Nerijus
^ permalink raw reply [flat|nested] 6+ messages in thread
* RE: Hang with Promise Ultra100 TX2 (kernel 2.4.18)
2004-01-15 11:49 ` Pasi Kärkkäinen
2004-01-15 15:42 ` Nerijus Baliunas
@ 2004-01-16 21:02 ` Cheng Huang
2004-01-17 9:51 ` Pasi Kärkkäinen
1 sibling, 1 reply; 6+ messages in thread
From: Cheng Huang @ 2004-01-16 21:02 UTC (permalink / raw)
To: 'Pasi K鋜kk鋓nen'; +Cc: linux-kernel
Thanks for replying. Can you explain a little bit where to get the driver for latest versions? Thanks.
-- Cheng
-----Original Message-----
From: Pasi K鋜kk鋓nen [mailto:pasik@iki.fi]
Sent: Thursday, January 15, 2004 5:49 AM
To: Cheng Huang
Cc: linux-kernel@vger.kernel.org; cheng@cse.wustl.edu
Subject: Re: Hang with Promise Ultra100 TX2 (kernel 2.4.18)
On Thu, Jan 15, 2004 at 03:17:12AM -0600, Cheng Huang wrote:
> I have to use kernel 2.4.18 because I need to install KURT (realtime
> linux) with it. However, my system hangs on boot with the following
> message:
>
> PDC20268: not 100% native mode: will probe irqs later
> PDC20268: ROM enabled at 0xff900000
> ide2: BM-DMA at 0xfcc0-0xfcc7, BIOS settings: hde:pio, hdf:pio
> ide3: BM-DMA at 0xfcc8-0xfccf, BIOS settings: hdg:pio, hdh:pio
>
> I have tried tricks I could find in through google, like setting boot
> parameters "hde=4866,255,63 hde=noprobe hdg=24321,255,163 hdg=noprobe".
> But it didn't work.
>
> Could anybody provide some clue about how to fix this problem? Thanks
> very much.
>
I think there has been a lot of bug fixes in the latest 2.4 kernels for
promise cards.
I'm running promise ultra133-tx2 successfully with 2.4.22 kernel.
Merge the promise driver from later 2.4.x kernels to 2.4.18 and recompile?
-- Pasi Kärkkäinen
^
. .
Linux
/ - \
Choice.of.the
.Next.Generation.
^ permalink raw reply [flat|nested] 6+ messages in thread* Re: Hang with Promise Ultra100 TX2 (kernel 2.4.18)
2004-01-16 21:02 ` Cheng Huang
@ 2004-01-17 9:51 ` Pasi Kärkkäinen
0 siblings, 0 replies; 6+ messages in thread
From: Pasi Kärkkäinen @ 2004-01-17 9:51 UTC (permalink / raw)
To: Cheng Huang; +Cc: linux-kernel
On Fri, Jan 16, 2004 at 03:02:44PM -0600, Cheng Huang wrote:
> Thanks for replying. Can you explain a little bit where to get the driver for latest versions? Thanks.
>
Copy the promise driver from 2.4.24 kernel to 2.4.18 kernel, and hope it
works :)
- Pasi Kärkkäinen
> -----Original Message-----
> From: Pasi K???kk???nen [mailto:pasik@iki.fi]
> Sent: Thursday, January 15, 2004 5:49 AM
> To: Cheng Huang
> Cc: linux-kernel@vger.kernel.org; cheng@cse.wustl.edu
> Subject: Re: Hang with Promise Ultra100 TX2 (kernel 2.4.18)
>
> On Thu, Jan 15, 2004 at 03:17:12AM -0600, Cheng Huang wrote:
> > I have to use kernel 2.4.18 because I need to install KURT (realtime
> > linux) with it. However, my system hangs on boot with the following
> > message:
> >
> > PDC20268: not 100% native mode: will probe irqs later
> > PDC20268: ROM enabled at 0xff900000
> > ide2: BM-DMA at 0xfcc0-0xfcc7, BIOS settings: hde:pio, hdf:pio
> > ide3: BM-DMA at 0xfcc8-0xfccf, BIOS settings: hdg:pio, hdh:pio
> >
> > I have tried tricks I could find in through google, like setting boot
> > parameters "hde=4866,255,63 hde=noprobe hdg=24321,255,163 hdg=noprobe".
> > But it didn't work.
> >
> > Could anybody provide some clue about how to fix this problem? Thanks
> > very much.
> >
>
> I think there has been a lot of bug fixes in the latest 2.4 kernels for
> promise cards.
>
> I'm running promise ultra133-tx2 successfully with 2.4.22 kernel.
>
> Merge the promise driver from later 2.4.x kernels to 2.4.18 and recompile?
>
> -- Pasi Kärkkäinen
>
> ^
> . .
> Linux
> / - \
> Choice.of.the
> .Next.Generation.
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
^ permalink raw reply [flat|nested] 6+ messages in thread
[parent not found: <20040115154755.CE15E5DA0@mx.ktv.lt>]
* RE: Hang with Promise Ultra100 TX2 (kernel 2.4.18)
[not found] <20040115154755.CE15E5DA0@mx.ktv.lt>
@ 2004-01-16 21:04 ` Cheng Huang
0 siblings, 0 replies; 6+ messages in thread
From: Cheng Huang @ 2004-01-16 21:04 UTC (permalink / raw)
To: 'Nerijus Baliunas'; +Cc: linux-kernel
Sorry not to mention. I have already applied the patch before I asked
this question. Any further suggestions? Thanks.
-- Cheng
-----Original Message-----
From: Nerijus Baliunas [mailto:nerijus@users.sourceforge.net]
Sent: Thursday, January 15, 2004 9:43 AM
To: linux-kernel@vger.kernel.org
Cc: Cheng Huang
Subject: Re: Hang with Promise Ultra100 TX2 (kernel 2.4.18)
On Thu, 15 Jan 2004 13:49:22 +0200 Pasi Kärkkäinen <pasik@iki.fi> wrote:
> On Thu, Jan 15, 2004 at 03:17:12AM -0600, Cheng Huang wrote:
> > I have to use kernel 2.4.18 because I need to install KURT (realtime
> > linux) with it. However, my system hangs on boot with the following
> > message:
>
> I think there has been a lot of bug fixes in the latest 2.4 kernels
for
> promise cards.
>
> I'm running promise ultra133-tx2 successfully with 2.4.22 kernel.
>
> Merge the promise driver from later 2.4.x kernels to 2.4.18 and
recompile?
When I used 2.4.18 I had Andre's ide.2.4.18-rc1.02152002.patch.bz2
applied.
Regards,
Nerijus
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2004-01-17 9:51 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2004-01-15 9:17 Hang with Promise Ultra100 TX2 (kernel 2.4.18) Cheng Huang
2004-01-15 11:49 ` Pasi Kärkkäinen
2004-01-15 15:42 ` Nerijus Baliunas
2004-01-16 21:02 ` Cheng Huang
2004-01-17 9:51 ` Pasi Kärkkäinen
[not found] <20040115154755.CE15E5DA0@mx.ktv.lt>
2004-01-16 21:04 ` Cheng Huang
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox