From: Brendan Pike <spike@superweb.ca>
To: linux-kernel@vger.kernel.org
Subject: Re: IDE Harddrive Performance
Date: Thu, 20 Dec 2001 09:12:28 -0400 [thread overview]
Message-ID: <01122009122800.27161@spikes> (raw)
Well i really cant explain this,
[root@spikes spike]# /sbin/hdparm -t /dev/hda
/dev/hda:
Timing buffered disk reads: 64 MB in 6.65 seconds = 9.62 MB/sec
[root@spikes spike]# cat /proc/ide/via
----------VIA BusMastering IDE Configuration----------------
Driver Version: 3.29
South Bridge: VIA vt82c586b
Revision: ISA 0x47 IDE 0x6
Highest DMA rate: UDMA33
BM-DMA base: 0xe000
PCI clock: 33MHz
Master Read Cycle IRDY: 1ws
Master Write Cycle IRDY: 1ws
BM IDE Status Register Read Retry: yes
Max DRDY Pulse Width: No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush: yes yes
End Sector FIFO flush: no no
Prefetch Buffer: yes yes
Post Write Buffer: yes no
Enabled: yes yes
Simplex only: no no
Cable Type: 40w 40w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode: UDMA PIO UDMA PIO
Address Setup: 30ns 120ns 30ns 120ns
Cmd Active: 90ns 90ns 90ns 90ns
Cmd Recovery: 30ns 30ns 30ns 30ns
Data Active: 90ns 330ns 90ns 330ns
Data Recovery: 30ns 270ns 30ns 270ns
Cycle Time: 60ns 600ns 60ns 600ns
Transfer Rate: 33.0MB/s 3.3MB/s 33.0MB/s 3.3MB/s
[root@spikes spike]# /sbin/hdparm -i /dev/hda
/dev/hda:
Model=FUJITSU MPG3409AT E, FwRev=82B9, SerialNo=VH06T1408HST
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=80063424
IORDY=yes, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
[root@spikes spike]# /sbin/hdparm /dev/hda
/dev/hda:
multcount = 16 (on)
I/O support = 3 (32-bit w/sync)
unmaskirq = 1 (on)
using_dma = 1 (on)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 4983/255/63, sectors = 80063424, start = 0
Kernel 2.4.16 without patches.
next reply other threads:[~2001-12-20 13:12 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2001-12-20 13:12 Brendan Pike [this message]
-- strict thread matches above, loose matches on Subject: below --
2001-12-23 17:55 IDE Harddrive Performance Wayne Whitney
2001-12-23 18:37 ` Mark Hahn
2001-12-22 18:20 Jim Radford
2001-12-22 21:36 ` Craig Knox
2001-12-23 8:11 ` Adam Keys
[not found] <Pine.LNX.4.33.0112201307120.9437-100000@coffee.psychology.mcmaster.ca>
2001-12-20 19:33 ` Brendan Pike
2001-12-20 19:25 Brendan Pike
2001-12-20 17:10 Brendan Pike
2001-12-20 17:22 ` Ryan Cumming
2001-12-20 17:41 ` Sebastian Dröge
2001-12-19 15:32 Thomas Deselaers
2001-12-19 15:44 ` Brendan Pike
2001-12-19 15:55 ` Lee Packham
2001-12-19 16:01 ` Jan Niehusmann
2001-12-19 16:18 ` Brendan Pike
2001-12-19 16:28 ` Oleg Artamonov
2001-12-19 16:44 ` Vojtech Pavlik
2001-12-19 16:59 ` Dmitry Pogosyan
[not found] ` <Pine.LNX.4.33.0112191101230.4575-100000@coffee.psychology.mcmaster.ca>
2001-12-19 16:37 ` Thomas Deselaers
2001-12-19 17:34 ` Mike Dresser
2001-12-19 15:55 ` Oleg Artamonov
2001-12-19 16:05 ` Thomas Deselaers
2001-12-19 16:15 ` Oleg Artamonov
2001-12-19 16:32 ` Thomas Deselaers
2001-12-19 16:38 ` Holger Lubitz
2001-12-22 8:21 ` Adam Keys
2001-12-22 8:56 ` Alan Cox
2001-12-22 10:10 ` Adam Keys
[not found] ` <01122215090500.01870@manta>
2001-12-22 13:23 ` Thomas Deselaers
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=01122009122800.27161@spikes \
--to=spike@superweb.ca \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox