Re: [PATCH V19 22/22] mmc: sdhci-pci-gli: enable UHS-II mode for GL9767

[Adrian Hunter <adrian.hunter@intel.com>]

On 29/08/24 13:15, Victor Shih wrote:
> From: Victor Shih <victor.shih@genesyslogic.com.tw>
> 
> Changes are:
>  * Enable the internal clock when do reset on UHS-II mode.
>  * Increase timeout value before detecting UHS-II interface.
>  * Add vendor settings for UHS-II mode.
> 
> Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
> Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
> Signed-off-by: Lucas Lai <lucas.lai@genesyslogic.com.tw>
> ---
> 
> Updates in V19:
>  - Use sdhci_gli_enable_internal_clock() to simplify the code
>    in the sdhci_gl9767_reset().
>  - Directly reading the SDHCI_PRESENT_STATE register to replace
>    the get_cd() avoids the possibility of the get_cd() sleeping
>    in the sdhci_gl9767_set_card_detect_debounce_time().
>  - Refine the position of gli_set_9767() in the sdhci_gl9767_reset().
> 
> Updates in V18:
>  - Add new register settings for gl9767.
>  - Add card_event in the sdhci_ops for gl9767.
>  - Add sdhci_gl9767_set_card_detect_debounce_time()
>    to configure the gl9767.
>  - Adjust the sdhci_gl9767_reset() process for gl9767.
> 
> Updates in V17:
>  - Use mmc_card_uhs2() to simplify the code in the sdhci_gl9767_reset().
>  - Use mmc_card_uhs2() to simplify the code in the
>    sdhci_gl9767_set_power().
>  - Add sdhci_gli_overcurrent_event_enable() to sdhci_gl9767_set_power().
> 
> Updates in V15:
>  - Add gl9767 to support uhs2 function.
> 
> ---
> 
>  drivers/mmc/host/sdhci-pci-gli.c | 211 ++++++++++++++++++++++++++++++-
>  1 file changed, 210 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/mmc/host/sdhci-pci-gli.c b/drivers/mmc/host/sdhci-pci-gli.c
> index e826e02a0d52..2375a810c2b8 100644
> --- a/drivers/mmc/host/sdhci-pci-gli.c
> +++ b/drivers/mmc/host/sdhci-pci-gli.c
> @@ -174,6 +174,15 @@
>  #define PCI_GLI_9755_MISC	    0x78
>  #define   PCI_GLI_9755_MISC_SSC_OFF    BIT(26)
>  
> +#define SDHCI_GLI_9767_SD_HOST_OPERATION_CTL				0x508
> +#define   SDHCI_GLI_9767_SD_HOST_OPERATION_CTL_CMD_CONFLICT_CHECK	  BIT(0)
> +#define   SDHCI_GLI_9767_SD_HOST_OPERATION_CTL_DEBOUNCE			  GENMASK(21, 16)
> +#define   SDHCI_GLI_9767_SD_HOST_OPERATION_CTL_DEBOUNCE_PLUG_IN_VALUE	  0x05
> +#define   SDHCI_GLI_9767_SD_HOST_OPERATION_CTL_DEBOUNCE_PLUG_OUT_VALUE	  0x3F
> +#define   SDHCI_GLI_9767_SD_HOST_OPERATION_CTL_DEBOUNCE_SCALE		  GENMASK(23, 22)
> +#define   SDHCI_GLI_9767_SD_HOST_OPERATION_CTL_DEBOUNCE_SCALE_1MS	  0x2
> +#define   SDHCI_GLI_9767_SD_HOST_OPERATION_CTL_DEBOUNCE_SCALE_10MS	  0x3
> +
>  #define SDHCI_GLI_9767_GM_BURST_SIZE			0x510
>  #define   SDHCI_GLI_9767_GM_BURST_SIZE_AXI_ALWAYS_SET	  BIT(8)
>  
> @@ -210,6 +219,13 @@
>  #define   PCIE_GLI_9767_SCR_CORE_PWR_D3_OFF		  BIT(21)
>  #define   PCIE_GLI_9767_SCR_CFG_RST_DATA_LINK_DOWN	  BIT(30)
>  
> +#define PCIE_GLI_9767_RESET_REG				0x8E4
> +#define   PCIE_GLI_9767_RESET_REG_SD_HOST_SW_RESET	  BIT(0)
> +
> +#define PCIE_GLI_9767_UHS2_PHY_SET_REG1				0x90C
> +#define   PCIE_GLI_9767_UHS2_PHY_SET_REG1_SERDES_INTR		  GENMASK(31, 29)
> +#define   PCIE_GLI_9767_UHS2_PHY_SET_REG1_SERDES_INTR_VALUE	  0x3
> +
>  #define PCIE_GLI_9767_SDHC_CAP			0x91C
>  #define   PCIE_GLI_9767_SDHC_CAP_SDEI_RESULT	  BIT(5)
>  
> @@ -228,9 +244,15 @@
>  #define   PCIE_GLI_9767_SD_EXPRESS_CTL_SD_EXPRESS_MODE	  BIT(1)
>  
>  #define PCIE_GLI_9767_SD_DATA_MULTI_CTL				0x944
> +#define   PCIE_GLI_9767_SD_DATA_MULTI_CTL_SELECT_UHS2		  BIT(5)
> +#define   PCIE_GLI_9767_SD_DATA_MULTI_CTL_UHS2_SWITCH_CTL	  BIT(8)
>  #define   PCIE_GLI_9767_SD_DATA_MULTI_CTL_DISCONNECT_TIME	  GENMASK(23, 16)
>  #define   PCIE_GLI_9767_SD_DATA_MULTI_CTL_DISCONNECT_TIME_VALUE	  0x64
>  
> +#define PCIE_GLI_9767_UHS2_PHY_SET_REG2					0x948
> +#define   PCIE_GLI_9767_UHS2_PHY_SET_REG2_SSC_PPM_SETTING		  GENMASK(22, 21)
> +#define   PCIE_GLI_9767_UHS2_PHY_SET_REG2_SSC_PPM_SETTING_VALUE		  0x0
> +
>  #define PCIE_GLI_9767_NORMAL_ERR_INT_STATUS_REG2			0x950
>  #define   PCIE_GLI_9767_NORMAL_ERR_INT_STATUS_REG2_SDEI_COMPLETE	  BIT(0)
>  
> @@ -240,6 +262,28 @@
>  #define PCIE_GLI_9767_NORMAL_ERR_INT_SIGNAL_EN_REG2				0x958
>  #define   PCIE_GLI_9767_NORMAL_ERR_INT_SIGNAL_EN_REG2_SDEI_COMPLETE_SIGNAL_EN	  BIT(0)
>  
> +#define PCIE_GLI_9767_UHS2_CTL1				0x95C
> +#define   PCIE_GLI_9767_UHS2_CTL1_TRANS_PASS		  BIT(5)
> +#define   PCIE_GLI_9767_UHS2_CTL1_TRANS_PASS_VALUE	  0x1
> +#define   PCIE_GLI_9767_UHS2_CTL1_DECODING_CTL		  BIT(6)
> +#define   PCIE_GLI_9767_UHS2_CTL1_DECODING_CTL_VALUE	  0x1
> +#define   PCIE_GLI_9767_UHS2_CTL1_SERDES_TRAN		  GENMASK(10, 7)
> +#define   PCIE_GLI_9767_UHS2_CTL1_SERDES_TRAN_VALUE	  0x3
> +#define   PCIE_GLI_9767_UHS2_CTL1_SERDES_RECV		  GENMASK(14, 11)
> +#define   PCIE_GLI_9767_UHS2_CTL1_SERDES_RECV_VALUE	  0xf
> +#define   PCIE_GLI_9767_UHS2_CTL1_DIR_TRANS		  GENMASK(16, 15)
> +#define   PCIE_GLI_9767_UHS2_CTL1_DIR_TRANS_VALUE	  0x0
> +#define   PCIE_GLI_9767_UHS2_CTL1_DIR_RECV		  GENMASK(18, 17)
> +#define   PCIE_GLI_9767_UHS2_CTL1_DIR_RECV_VALUE	  0x0
> +#define   PCIE_GLI_9767_UHS2_CTL1_PDRST			  BIT(25)
> +#define   PCIE_GLI_9767_UHS2_CTL1_PDRST_VALUE		  0x1
> +
> +#define PCIE_GLI_9767_UHS2_CTL2			0x964
> +#define   PCIE_GLI_9767_UHS2_CTL2_ZC		  GENMASK(3, 0)
> +#define   PCIE_GLI_9767_UHS2_CTL2_ZC_VALUE	  0xb
> +#define   PCIE_GLI_9767_UHS2_CTL2_ZC_CTL	  BIT(6)
> +#define   PCIE_GLI_9767_UHS2_CTL2_ZC_CTL_VALUE	  0x1
> +
>  #define GLI_MAX_TUNING_LOOP 40
>  
>  /* Genesys Logic chipset */
> @@ -1150,6 +1194,31 @@ static void sdhci_gl9767_set_clock(struct sdhci_host *host, unsigned int clock)
>  	gl9767_vhs_read(pdev);
>  }
>  
> +static void sdhci_gl9767_set_card_detect_debounce_time(struct sdhci_host *host)
> +{
> +	u32 value;
> +
> +	value = sdhci_readl(host, SDHCI_GLI_9767_SD_HOST_OPERATION_CTL);
> +	value &= ~(SDHCI_GLI_9767_SD_HOST_OPERATION_CTL_DEBOUNCE |
> +		   SDHCI_GLI_9767_SD_HOST_OPERATION_CTL_DEBOUNCE_SCALE);
> +	if (sdhci_readl(host, SDHCI_PRESENT_STATE) & SDHCI_CARD_PRESENT)
> +		value |= FIELD_PREP(SDHCI_GLI_9767_SD_HOST_OPERATION_CTL_DEBOUNCE,
> +				    SDHCI_GLI_9767_SD_HOST_OPERATION_CTL_DEBOUNCE_PLUG_IN_VALUE) |
> +			 FIELD_PREP(SDHCI_GLI_9767_SD_HOST_OPERATION_CTL_DEBOUNCE_SCALE,
> +				    SDHCI_GLI_9767_SD_HOST_OPERATION_CTL_DEBOUNCE_SCALE_1MS);
> +	else
> +		value |= FIELD_PREP(SDHCI_GLI_9767_SD_HOST_OPERATION_CTL_DEBOUNCE,
> +				    SDHCI_GLI_9767_SD_HOST_OPERATION_CTL_DEBOUNCE_PLUG_OUT_VALUE) |
> +			 FIELD_PREP(SDHCI_GLI_9767_SD_HOST_OPERATION_CTL_DEBOUNCE_SCALE,
> +				    SDHCI_GLI_9767_SD_HOST_OPERATION_CTL_DEBOUNCE_SCALE_10MS);
> +	sdhci_writel(host, value, SDHCI_GLI_9767_SD_HOST_OPERATION_CTL);
> +}
> +
> +static void sdhci_gl9767_card_event(struct sdhci_host *host)
> +{
> +	sdhci_gl9767_set_card_detect_debounce_time(host);
> +}
> +
>  static void gli_set_9767(struct sdhci_host *host)
>  {
>  	u32 value;
> @@ -1157,6 +1226,12 @@ static void gli_set_9767(struct sdhci_host *host)
>  	value = sdhci_readl(host, SDHCI_GLI_9767_GM_BURST_SIZE);
>  	value &= ~SDHCI_GLI_9767_GM_BURST_SIZE_AXI_ALWAYS_SET;
>  	sdhci_writel(host, value, SDHCI_GLI_9767_GM_BURST_SIZE);
> +
> +	value = sdhci_readl(host, SDHCI_GLI_9767_SD_HOST_OPERATION_CTL);
> +	value &= ~SDHCI_GLI_9767_SD_HOST_OPERATION_CTL_CMD_CONFLICT_CHECK;
> +	sdhci_writel(host, value, SDHCI_GLI_9767_SD_HOST_OPERATION_CTL);
> +
> +	sdhci_gl9767_set_card_detect_debounce_time(host);
>  }
>  
>  static void gl9767_hw_setting(struct sdhci_pci_slot *slot)
> @@ -1195,7 +1270,52 @@ static void gl9767_hw_setting(struct sdhci_pci_slot *slot)
>  
>  static void sdhci_gl9767_reset(struct sdhci_host *host, u8 mask)
>  {
> -	sdhci_reset(host, mask);
> +	struct sdhci_pci_slot *slot = sdhci_priv(host);
> +	struct pci_dev *pdev = slot->chip->pdev;
> +	u32 value;
> +	u8 rst;
> +
> +	/* need internal clock */
> +	if (mask & SDHCI_RESET_ALL) {
> +		sdhci_gli_enable_internal_clock(host);
> +
> +		gl9767_vhs_write(pdev);
> +
> +		pci_read_config_dword(pdev, PCIE_GLI_9767_RESET_REG, &value);
> +		value &= ~PCIE_GLI_9767_RESET_REG_SD_HOST_SW_RESET;
> +		pci_write_config_dword(pdev, PCIE_GLI_9767_RESET_REG, value);
> +
> +		if (read_poll_timeout_atomic(pci_read_config_dword, value,
> +					     !(value & PCIE_GLI_9767_RESET_REG_SD_HOST_SW_RESET),
> +					     1, 5, true, pdev, PCIE_GLI_9767_RESET_REG, &value)) {
> +			pr_warn("%s: %s: Reset SDHC AHB and TL-AMBA failure.\n",
> +				__func__, mmc_hostname(host->mmc));
> +			gl9767_vhs_read(pdev);
> +			return;
> +		}
> +		gl9767_vhs_read(pdev);
> +	}
> +
> +	if (mmc_card_uhs2(host->mmc)) {
> +		if (mask & (SDHCI_RESET_CMD | SDHCI_RESET_DATA)) {
> +			sdhci_writeb(host, mask, SDHCI_SOFTWARE_RESET);
> +			sdhci_gli_uhs2_reset_sd_tran(host);
> +			if (read_poll_timeout_atomic(sdhci_readb, rst, !(rst & mask), 10, 100000,
> +						     false, host, SDHCI_SOFTWARE_RESET)) {
> +				pr_err("%s: Reset 0x%x never completed.\n",
> +				       mmc_hostname(host->mmc), (int)mask);
> +				sdhci_dumpregs(host);
> +				/* manual clear */
> +				sdhci_writeb(host, 0, SDHCI_SOFTWARE_RESET);
> +				return;
> +			}

Same code in sdhci_gl9755_reset().  Might as well make it a separate
function so it can be shared.

> +		} else {
> +			sdhci_uhs2_reset(host, mask);
> +		}
> +	} else {
> +		sdhci_reset(host, mask);
> +	}
> +
>  	gli_set_9767(host);
>  }
>  
> @@ -1286,6 +1406,86 @@ static int gl9767_init_sd_express(struct mmc_host *mmc, struct mmc_ios *ios)
>  	return 0;
>  }
>  
> +static void gl9767_vendor_init(struct sdhci_host *host)
> +{
> +	struct sdhci_pci_slot *slot = sdhci_priv(host);
> +	struct pci_dev *pdev = slot->chip->pdev;
> +	u32 value;
> +
> +	gl9767_vhs_write(pdev);
> +
> +	pci_read_config_dword(pdev, PCIE_GLI_9767_UHS2_PHY_SET_REG1, &value);
> +	value |= FIELD_PREP(PCIE_GLI_9767_UHS2_PHY_SET_REG1_SERDES_INTR,
> +			    PCIE_GLI_9767_UHS2_PHY_SET_REG1_SERDES_INTR_VALUE);
> +	pci_write_config_dword(pdev, PCIE_GLI_9767_UHS2_PHY_SET_REG1, value);
> +
> +	pci_read_config_dword(pdev, PCIE_GLI_9767_UHS2_PHY_SET_REG2, &value);
> +	value |= FIELD_PREP(PCIE_GLI_9767_UHS2_PHY_SET_REG2_SSC_PPM_SETTING,
> +			    PCIE_GLI_9767_UHS2_PHY_SET_REG2_SSC_PPM_SETTING_VALUE);
> +	pci_write_config_dword(pdev, PCIE_GLI_9767_UHS2_PHY_SET_REG2, value);
> +
> +	pci_read_config_dword(pdev, PCIE_GLI_9767_UHS2_CTL1, &value);
> +	value |= FIELD_PREP(PCIE_GLI_9767_UHS2_CTL1_TRANS_PASS,
> +			    PCIE_GLI_9767_UHS2_CTL1_TRANS_PASS_VALUE) |
> +		 FIELD_PREP(PCIE_GLI_9767_UHS2_CTL1_DECODING_CTL,
> +			    PCIE_GLI_9767_UHS2_CTL1_DECODING_CTL_VALUE) |
> +		 FIELD_PREP(PCIE_GLI_9767_UHS2_CTL1_SERDES_TRAN,
> +			    PCIE_GLI_9767_UHS2_CTL1_SERDES_TRAN_VALUE) |
> +		 FIELD_PREP(PCIE_GLI_9767_UHS2_CTL1_SERDES_RECV,
> +			    PCIE_GLI_9767_UHS2_CTL1_SERDES_RECV_VALUE) |
> +		 FIELD_PREP(PCIE_GLI_9767_UHS2_CTL1_DIR_TRANS,
> +			    PCIE_GLI_9767_UHS2_CTL1_DIR_TRANS_VALUE) |
> +		 FIELD_PREP(PCIE_GLI_9767_UHS2_CTL1_DIR_RECV,
> +			    PCIE_GLI_9767_UHS2_CTL1_DIR_RECV_VALUE) |
> +		 FIELD_PREP(PCIE_GLI_9767_UHS2_CTL1_PDRST,
> +			    PCIE_GLI_9767_UHS2_CTL1_PDRST_VALUE);
> +	pci_write_config_dword(pdev, PCIE_GLI_9767_UHS2_CTL1, value);
> +
> +	pci_read_config_dword(pdev, PCIE_GLI_9767_UHS2_CTL2, &value);
> +	value |= FIELD_PREP(PCIE_GLI_9767_UHS2_CTL2_ZC,
> +			    PCIE_GLI_9767_UHS2_CTL2_ZC_VALUE) |
> +		 FIELD_PREP(PCIE_GLI_9767_UHS2_CTL2_ZC_CTL,
> +			    PCIE_GLI_9767_UHS2_CTL2_ZC_CTL_VALUE);
> +	pci_write_config_dword(pdev, PCIE_GLI_9767_UHS2_CTL2, value);
> +
> +	gl9767_vhs_read(pdev);
> +}
> +
> +static void sdhci_gl9767_set_power(struct sdhci_host *host, unsigned char mode,	unsigned short vdd)
> +{
> +	struct sdhci_pci_slot *slot = sdhci_priv(host);
> +	struct pci_dev *pdev = slot->chip->pdev;
> +	u32 value;
> +
> +	if (mmc_card_uhs2(host->mmc)) {
> +		gl9767_vhs_write(pdev);
> +
> +		pci_read_config_dword(pdev, PCIE_GLI_9767_SD_DATA_MULTI_CTL, &value);
> +		value |= PCIE_GLI_9767_SD_DATA_MULTI_CTL_SELECT_UHS2 |
> +			 PCIE_GLI_9767_SD_DATA_MULTI_CTL_UHS2_SWITCH_CTL;
> +		pci_write_config_dword(pdev, PCIE_GLI_9767_SD_DATA_MULTI_CTL, value);
> +
> +		gl9767_vhs_read(pdev);
> +
> +		sdhci_gli_overcurrent_event_enable(host, false);
> +		sdhci_uhs2_set_power(host, mode, vdd);
> +		sdhci_gli_overcurrent_event_enable(host, true);
> +	} else {
> +		gl9767_vhs_write(pdev);
> +
> +		pci_read_config_dword(pdev, PCIE_GLI_9767_SD_DATA_MULTI_CTL, &value);
> +		value &= ~(PCIE_GLI_9767_SD_DATA_MULTI_CTL_SELECT_UHS2 |
> +			   PCIE_GLI_9767_SD_DATA_MULTI_CTL_UHS2_SWITCH_CTL);
> +		pci_write_config_dword(pdev, PCIE_GLI_9767_SD_DATA_MULTI_CTL, value);
> +
> +		gl9767_vhs_read(pdev);
> +
> +		sdhci_gli_overcurrent_event_enable(host, false);
> +		sdhci_set_power(host, mode, vdd);
> +		sdhci_gli_overcurrent_event_enable(host, true);
> +	}
> +}
> +
>  static int gli_probe_slot_gl9750(struct sdhci_pci_slot *slot)
>  {
>  	struct sdhci_host *host = slot->host;
> @@ -1322,6 +1522,7 @@ static int gli_probe_slot_gl9767(struct sdhci_pci_slot *slot)
>  	host->mmc->caps2 |= MMC_CAP2_SD_EXP;
>  	host->mmc_host_ops.init_sd_express = gl9767_init_sd_express;
>  	sdhci_enable_v4_mode(host);
> +	gl9767_vendor_init(host);
>  
>  	return 0;
>  }
> @@ -1825,12 +2026,20 @@ static const struct sdhci_ops sdhci_gl9767_ops = {
>  	.reset			 = sdhci_gl9767_reset,
>  	.set_uhs_signaling	 = sdhci_set_uhs_signaling,
>  	.voltage_switch		 = sdhci_gl9767_voltage_switch,
> +	.dump_uhs2_regs		 = sdhci_uhs2_dump_regs,
> +	.set_timeout		 = sdhci_uhs2_set_timeout,
> +	.irq			 = sdhci_uhs2_irq,
> +	.set_power		 = sdhci_gl9767_set_power,
> +	.uhs2_pre_detect_init	 = sdhci_gli_pre_detect_init,
> +	.card_event		 = sdhci_gl9767_card_event,
>  };
>  
>  const struct sdhci_pci_fixes sdhci_gl9767 = {
>  	.quirks		= SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
>  	.quirks2	= SDHCI_QUIRK2_BROKEN_DDR50,
>  	.probe_slot	= gli_probe_slot_gl9767,
> +	.add_host	= sdhci_pci_uhs2_add_host,
> +	.remove_host	= sdhci_pci_uhs2_remove_host,
>  	.ops		= &sdhci_gl9767_ops,
>  #ifdef CONFIG_PM_SLEEP
>  	.resume		= sdhci_pci_gli_resume,